diff options
| -rw-r--r-- | Documentation/cciss.txt | 21 | ||||
| -rw-r--r-- | drivers/block/cciss.c | 748 | ||||
| -rw-r--r-- | drivers/block/cciss.h | 2 | ||||
| -rw-r--r-- | drivers/block/cciss_scsi.c | 195 | ||||
| -rw-r--r-- | drivers/block/xen-blkfront.c | 4 | ||||
| -rw-r--r-- | fs/bio.c | 9 |
6 files changed, 522 insertions, 457 deletions
diff --git a/Documentation/cciss.txt b/Documentation/cciss.txt index 63e59b8847c..8244c6442fa 100644 --- a/Documentation/cciss.txt +++ b/Documentation/cciss.txt @@ -112,27 +112,18 @@ Hot plug support for SCSI tape drives Hot plugging of SCSI tape drives is supported, with some caveats. The cciss driver must be informed that changes to the SCSI bus -have been made, in addition to and prior to informing the SCSI -mid layer. This may be done via the /proc filesystem. For example: +have been made. This may be done via the /proc filesystem. +For example: echo "rescan" > /proc/scsi/cciss0/1 -This causes the adapter to query the adapter about changes to the -physical SCSI buses and/or fibre channel arbitrated loop and the +This causes the driver to query the adapter about changes to the +physical SCSI buses and/or fibre channel arbitrated loop and the driver to make note of any new or removed sequential access devices or medium changers. The driver will output messages indicating what devices have been added or removed and the controller, bus, target and -lun used to address the device. Once this is done, the SCSI mid layer -can be informed of changes to the virtual SCSI bus which the driver -presents to it in the usual way. For example: - - echo scsi add-single-device 3 2 1 0 > /proc/scsi/scsi - -to add a device on controller 3, bus 2, target 1, lun 0. Note that -the driver makes an effort to preserve the devices positions -in the virtual SCSI bus, so if you are only moving tape drives -around on the same adapter and not adding or removing tape drives -from the adapter, informing the SCSI mid layer may not be necessary. +lun used to address the device. It then notifies the SCSI mid layer +of these changes. Note that the naming convention of the /proc filesystem entries contains a number in addition to the driver name. (E.g. "cciss0" diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c index 0ce0c279aab..b73116ef923 100644 --- a/drivers/block/cciss.c +++ b/drivers/block/cciss.c @@ -159,7 +159,7 @@ static int cciss_ioctl(struct inode *inode, struct file *filep, static int cciss_getgeo(struct block_device *bdev, struct hd_geometry *geo); static int cciss_revalidate(struct gendisk *disk); -static int rebuild_lun_table(ctlr_info_t *h, struct gendisk *del_disk); +static int rebuild_lun_table(ctlr_info_t *h, int first_time); static int deregister_disk(struct gendisk *disk, drive_info_struct *drv, int clear_all); @@ -171,7 +171,6 @@ static void cciss_geometry_inquiry(int ctlr, int logvol, int withirq, sector_t total_size, unsigned int block_size, InquiryData_struct *inq_buff, drive_info_struct *drv); -static void cciss_getgeometry(int cntl_num); static void __devinit cciss_interrupt_mode(ctlr_info_t *, struct pci_dev *, __u32); static void start_io(ctlr_info_t *h); @@ -929,8 +928,10 @@ static int cciss_ioctl(struct inode *inode, struct file *filep, return 0; } + case CCISS_DEREGDISK: + case CCISS_REGNEWD: case CCISS_REVALIDVOLS: - return rebuild_lun_table(host, NULL); + return rebuild_lun_table(host, 0); case CCISS_GETLUNINFO:{ LogvolInfo_struct luninfo; @@ -943,12 +944,6 @@ static int cciss_ioctl(struct inode *inode, struct file *filep, return -EFAULT; return 0; } - case CCISS_DEREGDISK: - return rebuild_lun_table(host, disk); - - case CCISS_REGNEWD: - return rebuild_lun_table(host, NULL); - case CCISS_PASSTHRU: { IOCTL_Command_struct iocommand; @@ -1134,7 +1129,7 @@ static int cciss_ioctl(struct inode *inode, struct file *filep, if (ioc->Request.Type.Direction == XFER_WRITE) { if (copy_from_user (buff[sg_used], data_ptr, sz)) { - status = -ENOMEM; + status = -EFAULT; goto cleanup1; } } else { @@ -1330,15 +1325,84 @@ static void cciss_softirq_done(struct request *rq) spin_unlock_irqrestore(&h->lock, flags); } +/* This function gets the serial number of a logical drive via + * inquiry page 0x83. Serial no. is 16 bytes. If the serial + * number cannot be had, for whatever reason, 16 bytes of 0xff + * are returned instead. + */ +static void cciss_get_serial_no(int ctlr, int logvol, int withirq, + unsigned char *serial_no, int buflen) +{ +#define PAGE_83_INQ_BYTES 64 + int rc; + unsigned char *buf; + + if (buflen > 16) + buflen = 16; + memset(serial_no, 0xff, buflen); + buf = kzalloc(PAGE_83_INQ_BYTES, GFP_KERNEL); + if (!buf) + return; + memset(serial_no, 0, buflen); + if (withirq) + rc = sendcmd_withirq(CISS_INQUIRY, ctlr, buf, + PAGE_83_INQ_BYTES, 1, logvol, 0x83, TYPE_CMD); + else + rc = sendcmd(CISS_INQUIRY, ctlr, buf, + PAGE_83_INQ_BYTES, 1, logvol, 0x83, NULL, TYPE_CMD); + if (rc == IO_OK) + memcpy(serial_no, &buf[8], buflen); + kfree(buf); + return; +} + +static void cciss_add_disk(ctlr_info_t *h, struct gendisk *disk, + int drv_index) +{ + disk->queue = blk_init_queue(do_cciss_request, &h->lock); + sprintf(disk->disk_name, "cciss/c%dd%d", h->ctlr, drv_index); + disk->major = h->major; + disk->first_minor = drv_index << NWD_SHIFT; + disk->fops = &cciss_fops; + disk->private_data = &h->drv[drv_index]; + + /* Set up queue information */ + blk_queue_bounce_limit(disk->queue, h->pdev->dma_mask); + + /* This is a hardware imposed limit. */ + blk_queue_max_hw_segments(disk->queue, MAXSGENTRIES); + + /* This is a limit in the driver and could be eliminated. */ + blk_queue_max_phys_segments(disk->queue, MAXSGENTRIES); + + blk_queue_max_sectors(disk->queue, h->cciss_max_sectors); + + blk_queue_softirq_done(disk->queue, cciss_softirq_done); + + disk->queue->queuedata = h; + + blk_queue_hardsect_size(disk->queue, + h->drv[drv_index].block_size); + + /* Make sure all queue data is written out before */ + /* setting h->drv[drv_index].queue, as setting this */ + /* allows the interrupt handler to start the queue */ + wmb(); + h->drv[drv_index].queue = disk->queue; + add_disk(disk); +} + /* This function will check the usage_count of the drive to be updated/added. - * If the usage_count is zero then the drive information will be updated and - * the disk will be re-registered with the kernel. If not then it will be - * left alone for the next reboot. The exception to this is disk 0 which - * will always be left registered with the kernel since it is also the - * controller node. Any changes to disk 0 will show up on the next - * reboot. + * If the usage_count is zero and it is a heretofore unknown drive, or, + * the drive's capacity, geometry, or serial number has changed, + * then the drive information will be updated and the disk will be + * re-registered with the kernel. If these conditions don't hold, + * then it will be left alone for the next reboot. The exception to this + * is disk 0 which will always be left registered with the kernel since it + * is also the controller node. Any changes to disk 0 will show up on + * the next reboot. */ -static void cciss_update_drive_info(int ctlr, int drv_index) +static void cciss_update_drive_info(int ctlr, int drv_index, int first_time) { ctlr_info_t *h = hba[ctlr]; struct gendisk *disk; @@ -1347,16 +1411,81 @@ static void cciss_update_drive_info(int ctlr, int drv_index) sector_t total_size; unsigned long flags = 0; int ret = 0; + drive_info_struct *drvinfo; + int was_only_controller_node; + + /* Get information about the disk and modify the driver structure */ + inq_buff = kmalloc(sizeof(InquiryData_struct), GFP_KERNEL); + drvinfo = kmalloc(sizeof(*drvinfo), GFP_KERNEL); + if (inq_buff == NULL || drvinfo == NULL) + goto mem_msg; + + /* See if we're trying to update the "controller node" + * this will happen the when the first logical drive gets + * created by ACU. + */ + was_only_controller_node = (drv_index == 0 && + h->drv[0].raid_level == -1); - /* if the disk already exists then deregister it before proceeding */ - if (h->drv[drv_index].raid_level != -1) { + /* testing to see if 16-byte CDBs are already being used */ + if (h->cciss_read == CCISS_READ_16) { + cciss_read_capacity_16(h->ctlr, drv_index, 1, + &total_size, &block_size); + + } else { + cciss_read_capacity(ctlr, drv_index, 1, + &total_size, &block_size); + + /* if read_capacity returns all F's this volume is >2TB */ + /* in size so we switch to 16-byte CDB's for all */ + /* read/write ops */ + if (total_size == 0xFFFFFFFFULL) { + cciss_read_capacity_16(ctlr, drv_index, 1, + &total_size, &block_size); + h->cciss_read = CCISS_READ_16; + h->cciss_write = CCISS_WRITE_16; + } else { + h->cciss_read = CCISS_READ_10; + h->cciss_write = CCISS_WRITE_10; + } + } + + cciss_geometry_inquiry(ctlr, drv_index, 1, total_size, block_size, + inq_buff, drvinfo); + drvinfo->block_size = block_size; + drvinfo->nr_blocks = total_size + 1; + + cciss_get_serial_no(ctlr, drv_index, 1, drvinfo->serial_no, + sizeof(drvinfo->serial_no)); + + /* Is it the same disk we already know, and nothing's changed? */ + if (h->drv[drv_index].raid_level != -1 && + ((memcmp(drvinfo->serial_no, + h->drv[drv_index].serial_no, 16) == 0) && + drvinfo->block_size == h->drv[drv_index].block_size && + drvinfo->nr_blocks == h->drv[drv_index].nr_blocks && + drvinfo->heads == h->drv[drv_index].heads && + drvinfo->sectors == h->drv[drv_index].sectors && + drvinfo->cylinders == h->drv[drv_index].cylinders)) + /* The disk is unchanged, nothing to update */ + goto freeret; + + /* If we get here it's not the same disk, or something's changed, + * so we need to * deregister it, and re-register it, if it's not + * in use. + * If the disk already exists then deregister it before proceeding + * (unless it's the first disk (for the controller node). + */ + if (h->drv[drv_index].raid_level != -1 && drv_index != 0) { + printk(KERN_WARNING "disk %d has changed.\n", drv_index); spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags); h->drv[drv_index].busy_configuring = 1; spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags); - /* deregister_disk sets h->drv[drv_index].queue = NULL */ - /* which keeps the interrupt handler from starting */ - /* the queue. */ + /* deregister_disk sets h->drv[drv_index].queue = NULL + * which keeps the interrupt handler from starting + * the queue. + */ ret = deregister_disk(h->gendisk[drv_index], &h->drv[drv_index], 0); h->drv[drv_index].busy_configuring = 0; @@ -1364,81 +1493,37 @@ static void cciss_update_drive_info(int ctlr, int drv_index) /* If the disk is in use return */ if (ret) - return; + goto freeret; - /* Get information about the disk and modify the driver structure */ - inq_buff = kmalloc(sizeof(InquiryData_struct), GFP_KERNEL); - if (inq_buff == NULL) - goto mem_msg; - - /* testing to see if 16-byte CDBs are already being used */ - if (h->cciss_read == CCISS_READ_16) { - cciss_read_capacity_16(h->ctlr, drv_index, 1, - &total_size, &block_size); - goto geo_inq; - } - - cciss_read_capacity(ctlr, drv_index, 1, - &total_size, &block_size); - - /* if read_capacity returns all F's this volume is >2TB in size */ - /* so we switch to 16-byte CDB's for all read/write ops */ - if (total_size == 0xFFFFFFFFULL) { - cciss_read_capacity_16(ctlr, drv_index, 1, - &total_size, &block_size); - h->cciss_read = CCISS_READ_16; - h->cciss_write = CCISS_WRITE_16; - } else { - h->cciss_read = CCISS_READ_10; - h->cciss_write = CCISS_WRITE_10; - } -geo_inq: - cciss_geometry_inquiry(ctlr, drv_index, 1, total_size, block_size, - inq_buff, &h->drv[drv_index]); + /* Save the new information from cciss_geometry_inquiry + * and serial number inquiry. + */ + h->drv[drv_index].block_size = drvinfo->block_size; + h->drv[drv_index].nr_blocks = drvinfo->nr_blocks; + h->drv[drv_index].heads = drvinfo->heads; + h->drv[drv_index].sectors = drvinfo->sectors; + h->drv[drv_index].cylinders = drvinfo->cylinders; + h->drv[drv_index].raid_level = drvinfo->raid_level; + memcpy(h->drv[drv_index].serial_no, drvinfo->serial_no, 16); ++h->num_luns; disk = h->gendisk[drv_index]; set_capacity(disk, h->drv[drv_index].nr_blocks); - /* if it's the controller it's already added */ - if (drv_index) { - disk->queue = blk_init_queue(do_cciss_request, &h->lock); - sprintf(disk->disk_name, "cciss/c%dd%d", ctlr, drv_index); - disk->major = h->major; - disk->first_minor = drv_index << NWD_SHIFT; - disk->fops = &cciss_fops; - disk->private_data = &h->drv[drv_index]; - - /* Set up queue information */ - blk_queue_bounce_limit(disk->queue, hba[ctlr]->pdev->dma_mask); - - /* This is a hardware imposed limit. */ - blk_queue_max_hw_segments(disk->queue, MAXSGENTRIES); - - /* This is a limit in the driver and could be eliminated. */ - blk_queue_max_phys_segments(disk->queue, MAXSGENTRIES); - - blk_queue_max_sectors(disk->queue, h->cciss_max_sectors); - - blk_queue_softirq_done(disk->queue, cciss_softirq_done); - - disk->queue->queuedata = hba[ctlr]; - - blk_queue_hardsect_size(disk->queue, - hba[ctlr]->drv[drv_index].block_size); - - /* Make sure all queue data is written out before */ - /* setting h->drv[drv_index].queue, as setting this */ - /* allows the interrupt handler to start the queue */ - wmb(); - h->drv[drv_index].queue = disk->queue; - add_disk(disk); - } + /* If it's not disk 0 (drv_index != 0) + * or if it was disk 0, but there was previously + * no actual corresponding configured logical drive + * (raid_leve == -1) then we want to update the + * logical drive's information. + */ + if (drv_index || first_time) + cciss_add_disk(h, disk, drv_index); - freeret: +freeret: kfree(inq_buff); + kfree(drvinfo); return; - mem_msg: +mem_msg: printk(KERN_ERR "cciss: out of memory\n"); goto freeret; } @@ -1448,21 +1533,91 @@ geo_inq: * where new drives will be added. If the index to be returned is greater * than the highest_lun index for the controller then highest_lun is set * to this new index. If there are no available indexes then -1 is returned. + * "controller_node" is used to know if this is a real logical drive, or just + * the controller node, which determines if this counts towards highest_lun. */ -static int cciss_find_free_drive_index(int ctlr) +static int cciss_find_free_drive_index(int ctlr, int controller_node) { int i; for (i = 0; i < CISS_MAX_LUN; i++) { if (hba[ctlr]->drv[i].raid_level == -1) { if (i > hba[ctlr]->highest_lun) - hba[ctlr]->highest_lun = i; + if (!controller_node) + hba[ctlr]->highest_lun = i; return i; } } return -1; } +/* cciss_add_gendisk finds a free hba[]->drv structure + * and allocates a gendisk if needed, and sets the lunid + * in the drvinfo structure. It returns the index into + * the ->drv[] array, or -1 if none are free. + * is_controller_node indicates whether highest_lun should + * count this disk, or if it's only being added to provide + * a means to talk to the controller in case no logical + * drives have yet been configured. + */ +static int cciss_add_gendisk(ctlr_info_t *h, __u32 lunid, int controller_node) +{ + int drv_index; + + drv_index = cciss_find_free_drive_index(h->ctlr, controller_node); + if (drv_index == -1) + return -1; + /*Check if the gendisk needs to be allocated */ + if (!h->gendisk[drv_index]) { + h->gendisk[drv_index] = + alloc_disk(1 << NWD_SHIFT); + if (!h->gendisk[drv_index]) { + printk(KERN_ERR "cciss%d: could not " + "allocate a new disk %d\n", + h->ctlr, drv_index); + return -1; + } + } + h->drv[drv_index].LunID = lunid; + + /* Don't need to mark this busy because nobody */ + /* else knows about this disk yet to contend */ + /* for access to it. */ + h->drv[drv_index].busy_configuring = 0; + wmb(); + return drv_index; +} + +/* This is for the special case of a controller which + * has no logical drives. In this case, we still need + * to register a disk so the controller can be accessed + * by the Array Config Utility. + */ +static void cciss_add_controller_node(ctlr_info_t *h) +{ + struct gendisk *disk; + int drv_index; + + if (h->gendisk[0] != NULL) /* already did this? Then bail. */ + return; + + drv_index = cciss_add_gendisk(h, 0, 1); + if (drv_index == -1) { + printk(KERN_WARNING "cciss%d: could not " + "add disk 0.\n", h->ctlr); + return; + } + h->drv[drv_index].block_size = 512; + h->drv[drv_index].nr_blocks = 0; + h->drv[drv_index].heads = 0; + h->drv[drv_index].sectors = 0; + h->drv[drv_index].cylinders = 0; + h->drv[drv_index].raid_level = -1; + memset(h->drv[drv_index].serial_no, 0, 16); + disk = h->gendisk[drv_index]; + cciss_add_disk(h, disk, drv_index); +} + /* This function will add and remove logical drives from the Logical * drive array of the controller and maintain persistency of ordering * so that mount points are preserved until the next reboot. This allows @@ -1470,15 +1625,12 @@ static int cciss_find_free_drive_index(int ctlr) * without a re-ordering of those drives. * INPUT * h = The controller to perform the operations on - * del_disk = The disk to remove if specified. If the value given - * is NULL then no disk is removed. */ -static int rebuild_lun_table(ctlr_info_t *h, struct gendisk *del_disk) +static int rebuild_lun_table(ctlr_info_t *h, int first_time) { int ctlr = h->ctlr; int num_luns; ReportLunData_struct *ld_buff = NULL; - drive_info_struct *drv = NULL; int return_code; int listlength = 0; int i; @@ -1487,6 +1639,9 @@ static int rebuild_lun_table(ctlr_info_t *h, struct gendisk *del_disk) __u32 lunid = 0; unsigned long flags; + if (!capable(CAP_SYS_RAWIO)) + return -EPERM; + /* Set busy_configuring flag for this operation */ spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags); if (h->busy_configuring) { @@ -1494,100 +1649,100 @@ static int rebuild_lun_table(ctlr_info_t *h, struct gendisk *del_disk) return -EBUSY; } h->busy_configuring = 1; + spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags); - /* if del_disk is NULL then we are being called to add a new disk - * and update the logical drive table. If it is not NULL then - * we will check if the disk is in use or not. - */ - if (del_disk != NULL) { - drv = get_drv(del_disk); - drv->busy_configuring = 1; - spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags); - return_code = deregister_disk(del_disk, drv, 1); - drv->busy_configuring = 0; - h->busy_configuring = 0; - return return_code; - } else { - spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags); - if (!capable(CAP_SYS_RAWIO)) - return -EPERM; + ld_buff = kzalloc(sizeof(ReportLunData_struct), GFP_KERNEL); + if (ld_buff == NULL) + goto mem_msg; - ld_buff = kzalloc(sizeof(ReportLunData_struct), GFP_KERNEL); - if (ld_buff == NULL) - goto mem_msg; - - return_code = sendcmd_withirq(CISS_REPORT_LOG, ctlr, ld_buff, - sizeof(ReportLunData_struct), 0, - 0, 0, TYPE_CMD); - - if (return_code == IO_OK) { - listlength = - be32_to_cpu(*(__be32 *) ld_buff->LUNListLength); - } else { /* reading number of logical volumes failed */ - printk(KERN_WARNING "cciss: report logical volume" - " command failed\n"); - listlength = 0; - goto freeret; - } + return_code = sendcmd_withirq(CISS_REPORT_LOG, ctlr, ld_buff, + sizeof(ReportLunData_struct), 0, + 0, 0, TYPE_CMD); - num_luns = listlength / 8; /* 8 bytes per entry */ - if (num_luns > CISS_MAX_LUN) { - num_luns = CISS_MAX_LUN; - printk(KERN_WARNING "cciss: more luns configured" - " on controller than can be handled by" - " this driver.\n"); + if (return_code == IO_OK) + listlength = be32_to_cpu(*(__be32 *) ld_buff->LUNListLength); + else { /* reading number of logical volumes failed */ + printk(KERN_WARNING "cciss: report logical volume" + " command failed\n"); + listlength = 0; + goto freeret; + } + + num_luns = listlength / 8; /* 8 bytes per entry */ + if (num_luns > CISS_MAX_LUN) { + num_luns = CISS_MAX_LUN; + printk(KERN_WARNING "cciss: more luns configured" + " on controller than can be handled by" + " this driver.\n"); + } + + if (num_luns == 0) + cciss_add_controller_node(h); + + /* Compare controller drive array to driver's drive array + * to see if any drives are missing on the controller due + * to action of Array Config Utility (user deletes drive) + * and deregister logical drives which have disappeared. + */ + for (i = 0; i <= h->highest_lun; i++) { + int j; + drv_found = 0; + for (j = 0; j < num_luns; j++) { + memcpy(&lunid, &ld_buff->LUN[j][0], 4); + lunid = le32_to_cpu(lunid); + if (h->drv[i].LunID == lunid) { + drv_found = 1; + break; + } } + if (!drv_found) { + /* Deregister it from the OS, it's gone. */ + spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags); + h->drv[i].busy_configuring = 1; + spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags); + return_code = deregister_disk(h->gendisk[i], + &h->drv[i], 1); + h->drv[i].busy_configuring = 0; + } + } + + /* Compare controller drive array to driver's drive array. + * Check for updates in the drive information and any new drives + * on the controller due to ACU adding logical drives, or changing + * a logical drive's size, etc. Reregister any new/changed drives + */ + for (i = 0; i < num_luns; i++) { + int j; - /* Compare controller drive array to drivers drive array. - * Check for updates in the drive information and any new drives - * on the controller. + drv_found = 0; + + memcpy(&lunid, &ld_buff->LUN[i][0], 4); + lunid = le32_to_cpu(lunid); + + /* Find if the LUN is already in the drive array + * of the driver. If so then update its info + * if not in use. If it does not exist then find + * the first free index and add it. */ - for (i = 0; i < num_luns; i++) { - int j; - - drv_found = 0; - - lunid = (0xff & - (unsigned int)(ld_buff->LUN[i][3])) << 24; - lunid |= (0xff & - (unsigned int)(ld_buff->LUN[i][2])) << 16; - lunid |= (0xff & - (unsigned int)(ld_buff->LUN[i][1])) << 8; - lunid |= 0xff & (unsigned int)(ld_buff->LUN[i][0]); - - /* Find if the LUN is already in the drive array - * of the controller. If so then update its info - * if not is use. If it does not exist then find - * the first free index and add it. - */ - for (j = 0; j <= h->highest_lun; j++) { - if (h->drv[j].LunID == lunid) { - drv_index = j; - drv_found = 1; - } + for (j = 0; j <= h->highest_lun; j++) { + if (h->drv[j].raid_level != -1 && + h->drv[j].LunID == lunid) { + drv_index = j; + drv_found = 1; + break; } + } - /* check if the drive was found already in the array */ - if (!drv_found) { - drv_index = cciss_find_free_drive_index(ctlr); - if (drv_index == -1) - goto freeret; - - /*Check if the gendisk needs to be allocated */ - if (!h->gendisk[drv_index]){ - h->gendisk[drv_index] = alloc_disk(1 << NWD_SHIFT); - if (!h->gendisk[drv_index]){ - printk(KERN_ERR "cciss: could not allocate new disk %d\n", drv_index); - goto mem_msg; - } - } - } - h->drv[drv_index].LunID = lunid; - cciss_update_drive_info(ctlr, drv_index); - } /* end for */ - } /* end else */ + /* check if the drive was found already in the array */ + if (!drv_found) { + drv_index = cciss_add_gendisk(h, lunid, 0); + if (drv_index == -1) + goto freeret; + } + cciss_update_drive_info(ctlr, drv_index, first_time); + } /* end for */ - freeret: +freeret: kfree(ld_buff); h->busy_configuring = 0; /* We return -1 here to tell the ACU that we have registered/updated @@ -1595,8 +1750,9 @@ static int rebuild_lun_table(ctlr_info_t *h, struct gendisk *del_disk) * additional times. */ return -1; - mem_msg: +mem_msg: printk(KERN_ERR "cciss: out of memory\n"); + h->busy_configuring = 0; goto freeret; } @@ -1652,15 +1808,15 @@ static int deregister_disk(struct gendisk *disk, drive_info_struct *drv, * other than disk 0 we will call put_disk. We do not * do this for disk 0 as we need it to be able to * configure the controller. - */ + */ if (clear_all){ /* This isn't pretty, but we need to find the * disk in our array and NULL our the pointer. * This is so that we will call alloc_disk if * this index is used again later. - */ + */ for (i=0; i < CISS_MAX_LUN; i++){ - if(h->gendisk[i] == disk){ + if (h->gendisk[i] == disk) { h->gendisk[i] = NULL; break; } @@ -1688,7 +1844,7 @@ static int deregister_disk(struct gendisk *disk, drive_info_struct *drv, if (drv == h->drv + h->highest_lun) { /* if so, find the new hightest lun */ int i, newhighest = -1; - for (i = 0; i < h->highest_lun; i++) { + for (i = 0; i <= h->highest_lun; i++) { /* if the disk has size > 0, it is available */ if (h->drv[i].heads) newhighest = i; @@ -3199,136 +3355,9 @@ err_out_free_res: return err; } -/* - * Gets information about the local volumes attached to the controller. +/* Function to find the first free pointer into our hba[] array + * Returns -1 if no free entries are left. */ -static void cciss_getgeometry(int cntl_num) -{ - ReportLunData_struct *ld_buff; - InquiryData_struct *inq_buff; - int return_code; - int i; - int listlength = 0; - __u32 lunid = 0; - unsigned block_size; - sector_t total_size; - - ld_buff = kzalloc(sizeof(ReportLunData_struct), GFP_KERNEL); - if (ld_buff == NULL) { - printk(KERN_ERR "cciss: out of memory\n"); - return; - } - inq_buff = kmalloc(sizeof(InquiryData_struct), GFP_KERNEL); - if (inq_buff == NULL) { - printk(KERN_ERR "cciss: out of memory\n"); - kfree(ld_buff); - return; - } - /* Get the firmware version */ - return_code = sendcmd(CISS_INQUIRY, cntl_num, inq_buff, - sizeof(InquiryData_struct), 0, 0, 0, NULL, - TYPE_CMD); - if (return_code == IO_OK) { - hba[cntl_num]->firm_ver[0] = inq_buff->data_byte[32]; - hba[cntl_num]->firm_ver[1] = inq_buff->data_byte[33]; - hba[cntl_num]->firm_ver[2] = inq_buff->data_byte[34]; - hba[cntl_num]->firm_ver[3] = inq_buff->data_byte[35]; - } else { /* send command failed */ - - printk(KERN_WARNING "cciss: unable to determine firmware" - " version of controller\n"); - } - /* Get the number of logical volumes */ - return_code = sendcmd(CISS_REPORT_LOG, cntl_num, ld_buff, - sizeof(ReportLunData_struct), 0, 0, 0, NULL, - TYPE_CMD); - - if (return_code == IO_OK) { -#ifdef CCISS_DEBUG - printk("LUN Data\n--------------------------\n"); -#endif /* CCISS_DEBUG */ - - listlength |= - (0xff & (unsigned int)(ld_buff->LUNListLength[0])) << 24; - listlength |= - (0xff & (unsigned int)(ld_buff->LUNListLength[1])) << 16; - listlength |= - (0xff & (unsigned int)(ld_buff->LUNListLength[2])) << 8; - listlength |= 0xff & (unsigned int)(ld_buff->LUNListLength[3]); - } else { /* reading number of logical volumes failed */ - - printk(KERN_WARNING "cciss: report logical volume" - " command failed\n"); - listlength = 0; - } - hba[cntl_num]->num_luns = listlength / 8; // 8 bytes pre entry - if (hba[cntl_num]->num_luns > CISS_MAX_LUN) { - printk(KERN_ERR - "ciss: only %d number of logical volumes supported\n", - CISS_MAX_LUN); - hba[cntl_num]->num_luns = CISS_MAX_LUN; - } -#ifdef CCISS_DEBUG - printk(KERN_DEBUG "Length = %x %x %x %x = %d\n", - ld_buff->LUNListLength[0], ld_buff->LUNListLength[1], - ld_buff->LUNListLength[2], ld_buff->LUNListLength[3], - hba[cntl_num]->num_luns); -#endif /* CCISS_DEBUG */ - - hba[cntl_num]->highest_lun = hba[cntl_num]->num_luns - 1; - for (i = 0; i < CISS_MAX_LUN; i++) { - if (i < hba[cntl_num]->num_luns) { - lunid = (0xff & (unsigned int)(ld_buff->LUN[i][3])) - << 24; - lunid |= (0xff & (unsigned int)(ld_buff->LUN[i][2])) - << 16; - lunid |= (0xff & (unsigned int)(ld_buff->LUN[i][1])) - << 8; - lunid |= 0xff & (unsigned int)(ld_buff->LUN[i][0]); - - hba[cntl_num]->drv[i].LunID = lunid; - -#ifdef CCISS_DEBUG - printk(KERN_DEBUG "LUN[%d]: %x %x %x %x = %x\n", i, - ld_buff->LUN[i][0], ld_buff->LUN[i][1], - ld_buff->LUN[i][2], ld_buff->LUN[i][3], - hba[cntl_num]->drv[i].LunID); -#endif /* CCISS_DEBUG */ - - /* testing to see if 16-byte CDBs are already being used */ - if(hba[cntl_num]->cciss_read == CCISS_READ_16) { - cciss_read_capacity_16(cntl_num, i, 0, - &total_size, &block_size); - goto geo_inq; - } - cciss_read_capacity(cntl_num, i, 0, &total_size, &block_size); - - /* If read_capacity returns all F's the logical is >2TB */ - /* so we switch to 16-byte CDBs for all read/write ops */ - if(total_size == 0xFFFFFFFFULL) { - cciss_read_capacity_16(cntl_num, i, 0, - &total_size, &block_size); - hba[cntl_num]->cciss_read = CCISS_READ_16; - hba[cntl_num]->cciss_write = CCISS_WRITE_16; - } else { - hba[cntl_num]->cciss_read = CCISS_READ_10; - hba[cntl_num]->cciss_write = CCISS_WRITE_10; - } -geo_inq: - cciss_geometry_inquiry(cntl_num, i, 0, total_size, - block_size, inq_buff, - &hba[cntl_num]->drv[i]); - } else { - /* initialize raid_level to indicate a free space */ - hba[cntl_num]->drv[i].raid_level = -1; - } - } - kfree(ld_buff); - kfree(inq_buff); -} - -/* Function to find the first free pointer into our hba[] array */ -/* Returns -1 if no free entries are left. */ static int alloc_cciss_hba(void) { int i; @@ -3340,11 +3369,6 @@ static int alloc_cciss_hba(void) p = kzalloc(sizeof(ctlr_info_t), GFP_KERNEL); if (!p) goto Enomem; - p->gendisk[0] = alloc_disk(1 << NWD_SHIFT); - if (!p->gendisk[0]) { - kfree(p); - goto Enomem; - } hba[i] = p; return i; } @@ -3472,11 +3496,13 @@ static int __devinit cciss_init_one(struct pci_dev *pdev, ((hba[i]->nr_cmds + BITS_PER_LONG - 1) / BITS_PER_LONG) * sizeof(unsigned long)); -#ifdef CCISS_DEBUG - printk(KERN_DEBUG "Scanning for drives on controller cciss%d\n", i); -#endif /* CCISS_DEBUG */ - - cciss_getgeometry(i); + hba[i]->num_luns = 0; + hba[i]->highest_lun = -1; + for (j = 0; j < CISS_MAX_LUN; j++) { + hba[i]->drv[j].raid_level = -1; + hba[i]->drv[j].queue = NULL; + hba[i]->gendisk[j] = NULL; + } cciss_scsi_setup(i); @@ -3489,76 +3515,10 @@ static int __devinit cciss_init_one(struct pci_dev *pdev, hba[i]->busy_initializing = 0; - do { - drive_info_struct *drv = &(hba[i]->drv[j]); - struct gendisk *disk = hba[i]->gendisk[j]; - struct request_queue *q; - - /* Check if the disk was allocated already */ - if (!disk){ - hba[i]->gendisk[j] = alloc_disk(1 << NWD_SHIFT); - disk = hba[i]->gendisk[j]; - } - - /* Check that the disk was able to be allocated */ - if (!disk) { - printk(KERN_ERR "cciss: unable to allocate memory for disk %d\n", j); - goto clean4; - } - - q = blk_init_queue(do_cciss_request, &hba[i]->lock); - if (!q) { - printk(KERN_ERR - "cciss: unable to allocate queue for disk %d\n", - j); - goto clean4; - } - drv->queue = q; - - blk_queue_bounce_limit(q, hba[i]->pdev->dma_mask); - - /* This is a hardware imposed limit. */ - blk_queue_max_hw_segments(q, MAXSGENTRIES); - - /* This is a limit in the driver and could be eliminated. */ - blk_queue_max_phys_segments(q, MAXSGENTRIES); - - blk_queue_max_sectors(q, hba[i]->cciss_max_sectors); - - blk_queue_softirq_done(q, cciss_softirq_done); - - q->queuedata = hba[i]; - sprintf(disk->disk_name, "cciss/c%dd%d", i, j); - disk->major = hba[i]->major; - disk->first_minor = j << NWD_SHIFT; - disk->fops = &cciss_fops; - disk->queue = q; - disk->private_data = drv; - disk->driverfs_dev = &pdev->dev; - /* we must register the controller even if no disks exist */ - /* this is for the online array utilities */ - if (!drv->heads && j) - continue; - blk_queue_hardsect_size(q, drv->block_size); - set_capacity(disk, drv->nr_blocks); - j++; - } while (j <= hba[i]->highest_lun); - - /* Make sure all queue data is written out before */ - /* interrupt handler, triggered by add_disk, */ - /* is allowed to start them. */ - wmb(); - - for (j = 0; j <= hba[i]->highest_lun; j++) - add_disk(hba[i]->gendisk[j]); - - /* we must register the controller even if no disks exist */ - if (hba[i]->highest_lun == -1) - add_disk(hba[i]->gendisk[0]); - + rebuild_lun_table(hba[i], 1); return 1; - clean4: +clean4: #ifdef CONFIG_CISS_SCSI_TAPE kfree(hba[i]->scsi_rejects.complete); #endif @@ -3573,9 +3533,9 @@ static int __devinit cciss_init_one(struct pci_dev *pdev, hba[i]->errinfo_pool, hba[i]->errinfo_pool_dhandle); free_irq(hba[i]->intr[SIMPLE_MODE_INT], hba[i]); - clean2: +clean2: unregister_blkdev(hba[i]->major, hba[i]->devname); - clean1: +clean1: hba[i]->busy_initializing = 0; /* cleanup any queues that may have been initialized */ for (j=0; j <= hba[i]->highest_lun; j++){ @@ -3654,7 +3614,9 @@ static void __devexit cciss_remove_one(struct pci_dev *pdev) } } +#ifdef CONFIG_CISS_SCSI_TAPE cciss_unregister_scsi(i); /* unhook from SCSI subsystem */ +#endif cciss_shutdown(pdev); diff --git a/drivers/block/cciss.h b/drivers/block/cciss.h index b70988dd33e..24a7efa993a 100644 --- a/drivers/block/cciss.h +++ b/drivers/block/cciss.h @@ -39,6 +39,8 @@ typedef struct _drive_info_struct *to prevent it from being opened or it's queue *from being started. */ + __u8 serial_no[16]; /* from inquiry page 0x83, */ + /* not necc. null terminated. */ } drive_info_struct; #ifdef CONFIG_CISS_SCSI_TAPE diff --git a/drivers/block/cciss_scsi.c b/drivers/block/cciss_scsi.c index e4bf9a11ca0..e1233aabda7 100644 --- a/drivers/block/cciss_scsi.c +++ b/drivers/block/cciss_scsi.c @@ -358,23 +358,68 @@ find_bus_target_lun(int ctlr, int *bus, int *target, int *lun) } return (!found); } +struct scsi2map { + char scsi3addr[8]; + int bus, target, lun; +}; static int cciss_scsi_add_entry(int ctlr, int hostno, - unsigned char *scsi3addr, int devtype) + unsigned char *scsi3addr, int devtype, + struct scsi2map *added, int *nadded) { /* assumes hba[ctlr]->scsi_ctlr->lock is held */ int n = ccissscsi[ctlr].ndevices; struct cciss_scsi_dev_t *sd; + int i, bus, target, lun; + unsigned char addr1[8], addr2[8]; if (n >= CCISS_MAX_SCSI_DEVS_PER_HBA) { printk("cciss%d: Too many devices, " "some will be inaccessible.\n", ctlr); return -1; } + + bus = target = -1; + lun = 0; + /* Is this device a non-zero lun of a multi-lun device */ + /* byte 4 of the 8-byte LUN addr will contain the logical unit no. */ + if (scsi3addr[4] != 0) { + /* Search through our list and find the device which */ + /* has the same 8 byte LUN address, excepting byte 4. */ + /* Assign the same bus and target for this new LUN. */ + /* Use the logical unit number from the firmware. */ + memcpy(addr1, scsi3addr, 8); + addr1[4] = 0; + for (i = 0; i < n; i++) { + sd = &ccissscsi[ctlr].dev[i]; + memcpy(addr2, sd->scsi3addr, 8); + addr2[4] = 0; + /* differ only in byte 4? */ + if (memcmp(addr1, addr2, 8) == 0) { + bus = sd->bus; + target = sd->target; + lun = scsi3addr[4]; + break; + } + } + } + sd = &ccissscsi[ctlr].dev[n]; - if (find_bus_target_lun(ctlr, &sd->bus, &sd->target, &sd->lun) != 0) - return -1; + if (lun == 0) { + if (find_bus_target_lun(ctlr, + &sd->bus, &sd->target, &sd->lun) != 0) + return -1; + } else { + sd->bus = bus; + sd->target = target; + sd->lun = lun; + } + added[*nadded].bus = sd->bus; + added[*nadded].target = sd->target; + added[*nadded].lun = sd->lun; + (*nadded)++; + memcpy(&sd->scsi3addr[0], scsi3addr, 8); sd->devtype = devtype; ccissscsi[ctlr].ndevices++; @@ -390,7 +435,8 @@ cciss_scsi_add_entry(int ctlr, int hostno, } static void -cciss_scsi_remove_entry(int ctlr, int hostno, int entry) +cciss_scsi_remove_entry(int ctlr, int hostno, int entry, + struct scsi2map *removed, int *nremoved) { /* assumes hba[ctlr]->scsi_ctlr->lock is held */ int i; @@ -398,6 +444,10 @@ cciss_scsi_remove_entry(int ctlr, int hostno, int entry) if (entry < 0 || entry >= CCISS_MAX_SCSI_DEVS_PER_HBA) return; sd = ccissscsi[ctlr].dev[entry]; + removed[*nremoved].bus = sd.bus; + removed[*nremoved].target = sd.target; + removed[*nremoved].lun = sd.lun; + (*nremoved)++; for (i=entry;i<ccissscsi[ctlr].ndevices-1;i++) ccissscsi[ctlr].dev[i] = ccissscsi[ctlr].dev[i+1]; ccissscsi[ctlr].ndevices--; @@ -417,6 +467,26 @@ cciss_scsi_remove_entry(int ctlr, int hostno, int entry) (a)[1] == (b)[1] && \ (a)[0] == (b)[0]) +static void fixup_botched_add(int ctlr, char *scsi3addr) +{ + /* called when scsi_add_device fails in order to re-adjust */ + /* ccissscsi[] to match the mid layer's view. */ + unsigned long flags; + int i, j; + CPQ_TAPE_LOCK(ctlr, flags); + for (i = 0; i < ccissscsi[ctlr].ndevices; i++) { + if (memcmp(scsi3addr, + ccissscsi[ctlr].dev[i].scsi3addr, 8) == 0) { + for (j = i; j < ccissscsi[ctlr].ndevices-1; j++) + ccissscsi[ctlr].dev[j] = + ccissscsi[ctlr].dev[j+1]; + ccissscsi[ctlr].ndevices--; + break; + } + } + CPQ_TAPE_UNLOCK(ctlr, flags); +} + static int adjust_cciss_scsi_table(int ctlr, int hostno, struct cciss_scsi_dev_t sd[], int nsds) @@ -429,13 +499,33 @@ adjust_cciss_scsi_table(int ctlr, int hostno, int i,j, found, changes=0; struct cciss_scsi_dev_t *csd; unsigned long flags; + struct scsi2map *added, *removed; + int nadded, nremoved; + struct Scsi_Host *sh = NULL; + + added = kzalloc(sizeof(*added) * CCISS_MAX_SCSI_DEVS_PER_HBA, + GFP_KERNEL); + removed = kzalloc(sizeof(*removed) * CCISS_MAX_SCSI_DEVS_PER_HBA, + GFP_KERNEL); + + if (!added || !removed) { + printk(KERN_WARNING "cciss%d: Out of memory in " + "adjust_cciss_scsi_table\n", ctlr); + goto free_and_out; + } CPQ_TAPE_LOCK(ctlr, flags); + if (hostno != -1) /* if it's not the first time... */ + sh = ((struct cciss_scsi_adapter_data_t *) + hba[ctlr]->scsi_ctlr)->scsi_host; + /* find any devices in ccissscsi[] that are not in sd[] and remove them from ccissscsi[] */ i = 0; + nremoved = 0; + nadded = 0; while(i<ccissscsi[ctlr].ndevices) { csd = &ccissscsi[ctlr].dev[i]; found=0; @@ -455,8 +545,9 @@ adjust_cciss_scsi_table(int ctlr, int hostno, /* printk("cciss%d: %s device c%db%dt%dl%d removed.\n", ctlr, scsi_device_type(csd->devtype), hostno, csd->bus, csd->target, csd->lun); */ - cciss_scsi_remove_entry(ctlr, hostno, i); - /* note, i not incremented */ + cciss_scsi_remove_entry(ctlr, hostno, i, + removed, &nremoved); + /* remove ^^^, hence i not incremented */ } else if (found == 1) { /* device is different kind */ changes++; @@ -464,8 +555,15 @@ adjust_cciss_scsi_table(int ctlr, int hostno, "(device type now %s).\n", ctlr, hostno, csd->bus, csd->target, csd->lun, scsi_device_type(csd->devtype)); + cciss_scsi_remove_entry(ctlr, hostno, i, + removed, &nremoved); + /* remove ^^^, hence i not incremented */ + if (cciss_scsi_add_entry(ctlr, hostno, + &sd[j].scsi3addr[0], sd[j].devtype, + added, &nadded) != 0) + /* we just removed one, so add can't fail. */ + BUG(); csd->devtype = sd[j].devtype; - i++; /* so just move along. */ } else /* device is same as it ever was, */ i++; /* so just move along. */ } @@ -489,7 +587,9 @@ adjust_cciss_scsi_table(int ctlr, int hostno, if (!found) { changes++; if (cciss_scsi_add_entry(ctlr, hostno, - &sd[i].scsi3addr[0], sd[i].devtype) != 0) + + &sd[i].scsi3addr[0], sd[i].devtype, + added, &nadded) != 0) break; } else if (found == 1) { /* should never happen... */ @@ -501,9 +601,50 @@ adjust_cciss_scsi_table(int ctlr, int hostno, } CPQ_TAPE_UNLOCK(ctlr, flags); - if (!changes) - printk("cciss%d: No device changes detected.\n", ctlr); + /* Don't notify scsi mid layer of any changes the first time through */ + /* (or if there are no changes) scsi_scan_host will do it later the */ + /* first time through. */ + if (hostno == -1 || !changes) + goto free_and_out; + + /* Notify scsi mid layer of any removed devices */ + for (i = 0; i < nremoved; i++) { + struct scsi_device *sdev = + scsi_device_lookup(sh, removed[i].bus, + removed[i].target, removed[i].lun); + if (sdev != NULL) { + scsi_remove_device(sdev); + scsi_device_put(sdev); + } else { + /* We don't expect to get here. */ + /* future cmds to this device will get selection */ + /* timeout as if the device was gone. */ + printk(KERN_WARNING "cciss%d: didn't find " + "c%db%dt%dl%d\n for removal.", + ctlr, hostno, removed[i].bus, + removed[i].target, removed[i].lun); + } + } + + /* Notify scsi mid layer of any added devices */ + for (i = 0; i < nadded; i++) { + int rc; + rc = scsi_add_device(sh, added[i].bus, + added[i].target, added[i].lun); + if (rc == 0) + continue; + printk(KERN_WARNING "cciss%d: scsi_add_device " + "c%db%dt%dl%d failed, device not added.\n", + ctlr, hostno, + added[i].bus, added[i].target, added[i].lun); + /* now we have to remove it from ccissscsi, */ + /* since it didn't get added to scsi mid layer */ + fixup_botched_add(ctlr, added[i].scsi3addr); + } +free_and_out: + kfree(added); + kfree(removed); return 0; } @@ -1355,32 +1496,6 @@ cciss_unregister_scsi(int ctlr) } static int -cciss_register_scsi(int ctlr) -{ - unsigned long flags; - - CPQ_TAPE_LOCK(ctlr, flags); - - /* Since this is really a block driver, the SCSI core may not be - initialized at init time, in which case, calling scsi_register_host - would hang. Instead, we do it later, via /proc filesystem - and rc scripts, when we know SCSI core is good to go. */ - - /* Only register if SCSI devices are detected. */ - if (ccissscsi[ctlr].ndevices != 0) { - ((struct cciss_scsi_adapter_data_t *) - hba[ctlr]->scsi_ctlr)->registered = 1; - CPQ_TAPE_UNLOCK(ctlr, flags); - return cciss_scsi_detect(ctlr); - } - CPQ_TAPE_UNLOCK(ctlr, flags); - printk(KERN_INFO - "cciss%d: No appropriate SCSI device detected, " - "SCSI subsystem not engaged.\n", ctlr); - return 0; -} - -static int cciss_engage_scsi(int ctlr) { struct cciss_scsi_adapter_data_t *sa; @@ -1391,15 +1506,15 @@ cciss_engage_scsi(int ctlr) sa = (struct cciss_scsi_adapter_data_t *) hba[ctlr]->scsi_ctlr; stk = &sa->cmd_stack; - if (((struct cciss_scsi_adapter_data_t *) - hba[ctlr]->scsi_ctlr)->registered) { + if (sa->registered) { printk("cciss%d: SCSI subsystem already engaged.\n", ctlr); spin_unlock_irqrestore(CCISS_LOCK(ctlr), flags); return ENXIO; } + sa->registered = 1; spin_unlock_irqrestore(CCISS_LOCK(ctlr), flags); cciss_update_non_disk_devices(ctlr, -1); - cciss_register_scsi(ctlr); + cciss_scsi_detect(ctlr); return 0; } @@ -1493,7 +1608,5 @@ static int cciss_eh_abort_handler(struct scsi_cmnd *scsicmd) /* If no tape support, then these become defined out of existence */ #define cciss_scsi_setup(cntl_num) -#define cciss_unregister_scsi(ctlr) -#define cciss_register_scsi(ctlr) #endif /* CONFIG_CISS_SCSI_TAPE */ diff --git a/drivers/block/xen-blkfront.c b/drivers/block/xen-blkfront.c index 9ae05c58423..3ca643cafcc 100644 --- a/drivers/block/xen-blkfront.c +++ b/drivers/block/xen-blkfront.c @@ -154,8 +154,8 @@ static int blkif_getgeo(struct block_device *bd, struct hd_geometry *hg) return 0; } -int blkif_ioctl(struct inode *inode, struct file *filep, - unsigned command, unsigned long argument) +static int blkif_ioctl(struct inode *inode, struct file *filep, + unsigned command, unsigned long argument) { struct blkfront_info *info = inode->i_bdev->bd_disk->private_data; @@ -77,11 +77,8 @@ struct bio_vec *bvec_alloc_bs(gfp_t gfp_mask, int nr, unsigned long *idx, struct */ bvl = mempool_alloc(bs->bvec_pools[*idx], gfp_mask); - if (bvl) { - struct biovec_slab *bp = bvec_slabs + *idx; - - memset(bvl, 0, bp->nr_vecs * sizeof(struct bio_vec)); - } + if (bvl) + memset(bvl, 0, bvec_nr_vecs(*idx) * sizeof(struct bio_vec)); return bvl; } @@ -149,7 +146,7 @@ struct bio *bio_alloc_bioset(gfp_t gfp_mask, int nr_iovecs, struct bio_set *bs) goto out; } bio->bi_flags |= idx << BIO_POOL_OFFSET; - bio->bi_max_vecs = bvec_slabs[idx].nr_vecs; + bio->bi_max_vecs = bvec_nr_vecs(idx); } bio->bi_io_vec = bvl; } |