diff options
| -rw-r--r-- | drivers/usb/gadget/inode.c | 60 |
1 files changed, 12 insertions, 48 deletions
diff --git a/drivers/usb/gadget/inode.c b/drivers/usb/gadget/inode.c index 10a5f7a164d..0f00249720b 100644 --- a/drivers/usb/gadget/inode.c +++ b/drivers/usb/gadget/inode.c @@ -59,11 +59,11 @@ * may serve as a source of device events, used to handle all control * requests other than basic enumeration. * - * - Then either immediately, or after a SET_CONFIGURATION control request, - * ep_config() is called when each /dev/gadget/ep* file is configured - * (by writing endpoint descriptors). Afterwards these files are used - * to write() IN data or to read() OUT data. To halt the endpoint, a - * "wrong direction" request is issued (like reading an IN endpoint). + * - Then, after a SET_CONFIGURATION control request, ep_config() is + * called when each /dev/gadget/ep* file is configured (by writing + * endpoint descriptors). Afterwards these files are used to write() + * IN data or to read() OUT data. To halt the endpoint, a "wrong + * direction" request is issued (like reading an IN endpoint). * * Unlike "usbfs" the only ioctl()s are for things that are rare, and maybe * not possible on all hardware. For example, precise fault handling with @@ -188,7 +188,6 @@ static struct dev_data *dev_new (void) enum ep_state { STATE_EP_DISABLED = 0, STATE_EP_READY, - STATE_EP_DEFER_ENABLE, STATE_EP_ENABLED, STATE_EP_UNBOUND, }; @@ -313,18 +312,10 @@ nonblock: if ((val = down_interruptible (&epdata->lock)) < 0) return val; -newstate: + switch (epdata->state) { case STATE_EP_ENABLED: break; - case STATE_EP_DEFER_ENABLE: - DBG (epdata->dev, "%s wait for host\n", epdata->name); - if ((val = wait_event_interruptible (epdata->wait, - epdata->state != STATE_EP_DEFER_ENABLE - || epdata->dev->state == STATE_DEV_UNBOUND - )) < 0) - goto fail; - goto newstate; // case STATE_EP_DISABLED: /* "can't happen" */ // case STATE_EP_READY: /* "can't happen" */ default: /* error! */ @@ -333,7 +324,6 @@ newstate: // FALLTHROUGH case STATE_EP_UNBOUND: /* clean disconnect */ val = -ENODEV; -fail: up (&epdata->lock); } return val; @@ -852,9 +842,9 @@ ep_config (struct file *fd, const char __user *buf, size_t len, loff_t *ptr) break; #endif default: - DBG (data->dev, "unconnected, %s init deferred\n", + DBG(data->dev, "unconnected, %s init abandoned\n", data->name); - data->state = STATE_EP_DEFER_ENABLE; + value = -EINVAL; } if (value == 0) { fd->f_op = &ep_io_operations; @@ -1393,8 +1383,6 @@ gadgetfs_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl) spin_lock (&dev->lock); dev->setup_abort = 0; if (dev->state == STATE_UNCONNECTED) { - struct usb_ep *ep; - struct ep_data *data; dev->state = STATE_CONNECTED; dev->dev->bMaxPacketSize0 = gadget->ep0->maxpacket; @@ -1411,27 +1399,6 @@ gadgetfs_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl) event->u.speed = gadget->speed; ep0_readable (dev); - list_for_each_entry (ep, &gadget->ep_list, ep_list) { - data = ep->driver_data; - /* ... down_trylock (&data->lock) ... */ - if (data->state != STATE_EP_DEFER_ENABLE) - continue; -#ifdef CONFIG_USB_GADGET_DUALSPEED - if (gadget->speed == USB_SPEED_HIGH) - value = usb_ep_enable (ep, &data->hs_desc); - else -#endif /* CONFIG_USB_GADGET_DUALSPEED */ - value = usb_ep_enable (ep, &data->desc); - if (value) { - ERROR (dev, "deferred %s enable --> %d\n", - data->name, value); - continue; - } - data->state = STATE_EP_ENABLED; - wake_up (&data->wait); - DBG (dev, "woke up %s waiters\n", data->name); - } - /* host may have given up waiting for response. we can miss control * requests handled lower down (device/endpoint status and features); * then ep0_{read,write} will report the wrong status. controller @@ -1852,16 +1819,13 @@ static struct usb_gadget_driver probe_driver = { * this one's optional except for high-speed hardware * . device descriptor * - * Endpoints are not yet enabled. Drivers may want to immediately - * initialize them, using the /dev/gadget/ep* files that are available - * as soon as the kernel sees the configuration, or they can wait - * until device configuration and interface altsetting changes create + * Endpoints are not yet enabled. Drivers must wait until device + * configuration and interface altsetting changes create * the need to configure (or unconfigure) them. * * After initialization, the device stays active for as long as that - * $CHIP file is open. Events may then be read from that descriptor, - * such as configuration notifications. More complex drivers will handle - * some control requests in user space. + * $CHIP file is open. Events must then be read from that descriptor, + * such as configuration notifications. */ static int is_valid_config (struct usb_config_descriptor *config) |