diff options
Diffstat (limited to 'drivers/ide/pci')
| -rw-r--r-- | drivers/ide/pci/cmd640.c | 2 | ||||
| -rw-r--r-- | drivers/ide/pci/delkin_cb.c | 28 | ||||
| -rw-r--r-- | drivers/ide/pci/it8213.c | 3 | ||||
| -rw-r--r-- | drivers/ide/pci/ns87415.c | 6 | ||||
| -rw-r--r-- | drivers/ide/pci/opti621.c | 221 | ||||
| -rw-r--r-- | drivers/ide/pci/sis5513.c | 5 |
6 files changed, 59 insertions, 206 deletions
diff --git a/drivers/ide/pci/cmd640.c b/drivers/ide/pci/cmd640.c index aaf38109eae..b38a1980dcd 100644 --- a/drivers/ide/pci/cmd640.c +++ b/drivers/ide/pci/cmd640.c @@ -747,9 +747,11 @@ static int __init cmd640x_init(void) ide_std_init_ports(&hw[0], 0x1f0, 0x3f6); hw[0].irq = 14; + hw[0].chipset = ide_cmd640; ide_std_init_ports(&hw[1], 0x170, 0x376); hw[1].irq = 15; + hw[1].chipset = ide_cmd640; printk(KERN_INFO "cmd640: buggy cmd640%c interface on %s, config=0x%02x" "\n", 'a' + cmd640_chip_version - 1, bus_type, cfr); diff --git a/drivers/ide/pci/delkin_cb.c b/drivers/ide/pci/delkin_cb.c index b9e457996d0..af0f30051d5 100644 --- a/drivers/ide/pci/delkin_cb.c +++ b/drivers/ide/pci/delkin_cb.c @@ -47,13 +47,18 @@ static const struct ide_port_ops delkin_cb_port_ops = { .quirkproc = ide_undecoded_slave, }; +static const struct ide_port_info delkin_cb_port_info = { + .port_ops = &delkin_cb_port_ops, + .host_flags = IDE_HFLAG_IO_32BIT | IDE_HFLAG_UNMASK_IRQS | + IDE_HFLAG_NO_DMA, +}; + static int __devinit delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id) { unsigned long base; hw_regs_t hw; ide_hwif_t *hwif = NULL; - ide_drive_t *drive; int i, rc; u8 idx[4] = { 0xff, 0xff, 0xff, 0xff }; @@ -79,6 +84,7 @@ delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id) memset(&hw, 0, sizeof(hw)); ide_std_init_ports(&hw, base + 0x10, base + 0x1e); hw.irq = dev->irq; + hw.dev = &dev->dev; hw.chipset = ide_pci; /* this enables IRQ sharing */ hwif = ide_find_port(); @@ -89,26 +95,16 @@ delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id) ide_init_port_data(hwif, i); ide_init_port_hw(hwif, &hw); - hwif->port_ops = &delkin_cb_port_ops; idx[0] = i; - ide_device_add(idx, NULL); - - if (!hwif->present) - goto out_disable; + ide_device_add(idx, &delkin_cb_port_info); pci_set_drvdata(dev, hwif); - hwif->dev = &dev->dev; - drive = &hwif->drives[0]; - if (drive->present) { - drive->io_32bit = 1; - drive->unmask = 1; - } + return 0; out_disable: - printk(KERN_ERR "delkin_cb: no IDE devices found\n"); pci_release_regions(dev); pci_disable_device(dev); return -ENODEV; @@ -139,14 +135,12 @@ static struct pci_driver driver = { .remove = delkin_cb_remove, }; -static int -delkin_cb_init (void) +static int __init delkin_cb_init(void) { return pci_register_driver(&driver); } -static void -delkin_cb_exit (void) +static void __exit delkin_cb_exit(void) { pci_unregister_driver(&driver); } diff --git a/drivers/ide/pci/it8213.c b/drivers/ide/pci/it8213.c index 9053c8771e6..2b71bdf74e7 100644 --- a/drivers/ide/pci/it8213.c +++ b/drivers/ide/pci/it8213.c @@ -184,8 +184,7 @@ static const struct ide_port_info it8213_chipsets[] __devinitdata = { static int __devinit it8213_init_one(struct pci_dev *dev, const struct pci_device_id *id) { - ide_setup_pci_device(dev, &it8213_chipsets[id->driver_data]); - return 0; + return ide_setup_pci_device(dev, &it8213_chipsets[id->driver_data]); } static const struct pci_device_id it8213_pci_tbl[] = { diff --git a/drivers/ide/pci/ns87415.c b/drivers/ide/pci/ns87415.c index fec4955f449..a7a41bb8277 100644 --- a/drivers/ide/pci/ns87415.c +++ b/drivers/ide/pci/ns87415.c @@ -225,10 +225,6 @@ static int ns87415_dma_setup(ide_drive_t *drive) return 1; } -#ifndef ide_default_irq -#define ide_default_irq(irq) 0 -#endif - static void __devinit init_hwif_ns87415 (ide_hwif_t *hwif) { struct pci_dev *dev = to_pci_dev(hwif->dev); @@ -288,7 +284,7 @@ static void __devinit init_hwif_ns87415 (ide_hwif_t *hwif) } if (!using_inta) - hwif->irq = ide_default_irq(hwif->io_ports.data_addr); + hwif->irq = __ide_default_irq(hwif->io_ports.data_addr); else if (!hwif->irq && hwif->mate && hwif->mate->irq) hwif->irq = hwif->mate->irq; /* share IRQ with mate */ diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c index 6e99080497b..725c80508d9 100644 --- a/drivers/ide/pci/opti621.c +++ b/drivers/ide/pci/opti621.c @@ -81,8 +81,6 @@ * 0.5 doesn't work. */ -#define OPTI621_DEBUG /* define for debug messages */ - #include <linux/types.h> #include <linux/module.h> #include <linux/kernel.h> @@ -92,28 +90,6 @@ #include <asm/io.h> -//#define OPTI621_MAX_PIO 3 -/* In fact, I do not have any PIO 4 drive - * (address: 25 ns, data: 70 ns, recovery: 35 ns), - * but OPTi 82C621 is programmable and it can do (minimal values): - * on 40MHz PCI bus (pulse 25 ns): - * address: 25 ns, data: 25 ns, recovery: 50 ns; - * on 20MHz PCI bus (pulse 50 ns): - * address: 50 ns, data: 50 ns, recovery: 100 ns. - */ - -/* #define READ_PREFETCH 0 */ -/* Uncomment for disable read prefetch. - * There is some readprefetch capatibility in hdparm, - * but when I type hdparm -P 1 /dev/hda, I got errors - * and till reset drive is inaccessible. - * This (hw) read prefetch is safe on my drive. - */ - -#ifndef READ_PREFETCH -#define READ_PREFETCH 0x40 /* read prefetch is enabled */ -#endif /* else read prefetch is disabled */ - #define READ_REG 0 /* index of Read cycle timing register */ #define WRITE_REG 1 /* index of Write cycle timing register */ #define CNTRL_REG 3 /* index of Control register */ @@ -122,51 +98,8 @@ static int reg_base; -#define PIO_NOT_EXIST 254 -#define PIO_DONT_KNOW 255 - static DEFINE_SPINLOCK(opti621_lock); -/* there are stored pio numbers from other calls of opti621_set_pio_mode */ -static void compute_pios(ide_drive_t *drive, const u8 pio) -/* Store values into drive->drive_data - * second_contr - 0 for primary controller, 1 for secondary - * slave_drive - 0 -> pio is for master, 1 -> pio is for slave - * pio - PIO mode for selected drive (for other we don't know) - */ -{ - int d; - ide_hwif_t *hwif = HWIF(drive); - - drive->drive_data = pio; - - for (d = 0; d < 2; ++d) { - drive = &hwif->drives[d]; - if (drive->present) { - if (drive->drive_data == PIO_DONT_KNOW) - drive->drive_data = ide_get_best_pio_mode(drive, 255, 3); -#ifdef OPTI621_DEBUG - printk("%s: Selected PIO mode %d\n", - drive->name, drive->drive_data); -#endif - } else { - drive->drive_data = PIO_NOT_EXIST; - } - } -} - -static int cmpt_clk(int time, int bus_speed) -/* Returns (rounded up) time in clocks for time in ns, - * with bus_speed in MHz. - * Example: bus_speed = 40 MHz, time = 80 ns - * 1000/40 = 25 ns (clk value), - * 80/25 = 3.2, rounded up to 4 (I hope ;-)). - * Use idebus=xx to select right frequency. - */ -{ - return ((time*bus_speed+999)/1000); -} - /* Write value to register reg, base of register * is at reg_base (0x1f0 primary, 0x170 secondary, * if not changed by PCI configuration). @@ -199,83 +132,29 @@ static u8 read_reg(int reg) return ret; } -typedef struct pio_clocks_s { - int address_time; /* Address setup (clocks) */ - int data_time; /* Active/data pulse (clocks) */ - int recovery_time; /* Recovery time (clocks) */ -} pio_clocks_t; - -static void compute_clocks(int pio, pio_clocks_t *clks) -{ - if (pio != PIO_NOT_EXIST) { - int adr_setup, data_pls; - int bus_speed = ide_pci_clk ? ide_pci_clk : system_bus_clock(); - - adr_setup = ide_pio_timings[pio].setup_time; - data_pls = ide_pio_timings[pio].active_time; - clks->address_time = cmpt_clk(adr_setup, bus_speed); - clks->data_time = cmpt_clk(data_pls, bus_speed); - clks->recovery_time = cmpt_clk(ide_pio_timings[pio].cycle_time - - adr_setup-data_pls, bus_speed); - if (clks->address_time < 1) - clks->address_time = 1; - if (clks->address_time > 4) - clks->address_time = 4; - if (clks->data_time < 1) - clks->data_time = 1; - if (clks->data_time > 16) - clks->data_time = 16; - if (clks->recovery_time < 2) - clks->recovery_time = 2; - if (clks->recovery_time > 17) - clks->recovery_time = 17; - } else { - clks->address_time = 1; - clks->data_time = 1; - clks->recovery_time = 2; - /* minimal values */ - } -} - static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio) { - /* primary and secondary drives share some registers, - * so we have to program both drives - */ + ide_hwif_t *hwif = drive->hwif; + ide_drive_t *pair = ide_get_paired_drive(drive); unsigned long flags; - u8 pio1 = 0, pio2 = 0; - pio_clocks_t first, second; - int ax, drdy; - u8 cycle1, cycle2, misc; - ide_hwif_t *hwif = HWIF(drive); - - /* sets drive->drive_data for both drives */ - compute_pios(drive, pio); - pio1 = hwif->drives[0].drive_data; - pio2 = hwif->drives[1].drive_data; - - compute_clocks(pio1, &first); - compute_clocks(pio2, &second); - - /* ax = max(a1,a2) */ - ax = (first.address_time < second.address_time) ? second.address_time : first.address_time; - - drdy = 2; /* DRDY is default 2 (by OPTi Databook) */ - - cycle1 = ((first.data_time-1)<<4) | (first.recovery_time-2); - cycle2 = ((second.data_time-1)<<4) | (second.recovery_time-2); - misc = READ_PREFETCH | ((ax-1)<<4) | ((drdy-2)<<1); - -#ifdef OPTI621_DEBUG - printk("%s: master: address: %d, data: %d, " - "recovery: %d, drdy: %d [clk]\n", - hwif->name, ax, first.data_time, - first.recovery_time, drdy); - printk("%s: slave: address: %d, data: %d, " - "recovery: %d, drdy: %d [clk]\n", - hwif->name, ax, second.data_time, - second.recovery_time, drdy); -#endif + u8 tim, misc, addr_pio = pio, clk; + + /* DRDY is default 2 (by OPTi Databook) */ + static const u8 addr_timings[2][5] = { + { 0x20, 0x10, 0x00, 0x00, 0x00 }, /* 33 MHz */ + { 0x10, 0x10, 0x00, 0x00, 0x00 }, /* 25 MHz */ + }; + static const u8 data_rec_timings[2][5] = { + { 0x5b, 0x45, 0x32, 0x21, 0x20 }, /* 33 MHz */ + { 0x48, 0x34, 0x21, 0x10, 0x10 } /* 25 MHz */ + }; + + drive->drive_data = XFER_PIO_0 + pio; + + if (pair->present) { + if (pair->drive_data && pair->drive_data < drive->drive_data) + addr_pio = pair->drive_data - XFER_PIO_0; + } spin_lock_irqsave(&opti621_lock, flags); @@ -289,24 +168,21 @@ static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio) (void)inb(reg_base + CNTRL_REG); /* if reads 0xc0, no interface exist? */ read_reg(CNTRL_REG); - /* read version, probably 0 */ - read_reg(STRAP_REG); - /* program primary drive */ - /* select Index-0 for Register-A */ - write_reg(0, MISC_REG); - /* set read cycle timings */ - write_reg(cycle1, READ_REG); - /* set write cycle timings */ - write_reg(cycle1, WRITE_REG); + /* check CLK speed */ + clk = read_reg(STRAP_REG) & 1; + + printk(KERN_INFO "%s: CLK = %d MHz\n", hwif->name, clk ? 25 : 33); - /* program secondary drive */ - /* select Index-1 for Register-B */ - write_reg(1, MISC_REG); + tim = data_rec_timings[clk][pio]; + misc = addr_timings[clk][addr_pio]; + + /* select Index-0/1 for Register-A/B */ + write_reg(drive->select.b.unit, MISC_REG); /* set read cycle timings */ - write_reg(cycle2, READ_REG); + write_reg(tim, READ_REG); /* set write cycle timings */ - write_reg(cycle2, WRITE_REG); + write_reg(tim, WRITE_REG); /* use Register-A for drive 0 */ /* use Register-B for drive 1 */ @@ -319,45 +195,26 @@ static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio) spin_unlock_irqrestore(&opti621_lock, flags); } -static void __devinit opti621_port_init_devs(ide_hwif_t *hwif) -{ - hwif->drives[0].drive_data = PIO_DONT_KNOW; - hwif->drives[1].drive_data = PIO_DONT_KNOW; -} - static const struct ide_port_ops opti621_port_ops = { - .port_init_devs = opti621_port_init_devs, .set_pio_mode = opti621_set_pio_mode, }; -static const struct ide_port_info opti621_chipsets[] __devinitdata = { - { /* 0 */ - .name = "OPTI621", - .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} }, - .port_ops = &opti621_port_ops, - .host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA, - .pio_mask = ATA_PIO3, - .swdma_mask = ATA_SWDMA2, - .mwdma_mask = ATA_MWDMA2, - }, { /* 1 */ - .name = "OPTI621X", - .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} }, - .port_ops = &opti621_port_ops, - .host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA, - .pio_mask = ATA_PIO3, - .swdma_mask = ATA_SWDMA2, - .mwdma_mask = ATA_MWDMA2, - } +static const struct ide_port_info opti621_chipset __devinitdata = { + .name = "OPTI621/X", + .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} }, + .port_ops = &opti621_port_ops, + .host_flags = IDE_HFLAG_NO_DMA, + .pio_mask = ATA_PIO4, }; static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_device_id *id) { - return ide_setup_pci_device(dev, &opti621_chipsets[id->driver_data]); + return ide_setup_pci_device(dev, &opti621_chipset); } static const struct pci_device_id opti621_pci_tbl[] = { { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 }, - { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 }, + { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 0 }, { 0, }, }; MODULE_DEVICE_TABLE(pci, opti621_pci_tbl); diff --git a/drivers/ide/pci/sis5513.c b/drivers/ide/pci/sis5513.c index 4b0b85d8faf..e127eb25ab6 100644 --- a/drivers/ide/pci/sis5513.c +++ b/drivers/ide/pci/sis5513.c @@ -569,6 +569,11 @@ static int __devinit sis5513_init_one(struct pci_dev *dev, const struct pci_devi { struct ide_port_info d = sis5513_chipset; u8 udma_rates[] = { 0x00, 0x00, 0x07, 0x1f, 0x3f, 0x3f, 0x7f, 0x7f }; + int rc; + + rc = pci_enable_device(dev); + if (rc) + return rc; if (sis_find_family(dev) == 0) return -ENOTSUPP; |