aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-03-21atm: convert mpc device to using netdev_opsStephen Hemminger
This converts the mpc device to using new netdevice_ops. Compile tested only, needs more than usual review since device was swaping pointers around etc. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21sfc: Implement adaptive IRQ moderationBen Hutchings
Calculate a score for each 1000 IRQs: - TX completions are worth 1 point - RX completions are worth 4 if merged using LRO or 2 otherwise Reduce moderation if the score is less than 10000, down to a minimum of 5 us. Increase moderation if the score is more than 20000, up to the specified maximum. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21sfc: Optimise falcon_writel_page_locked() for page > 0Ben Hutchings
The bug this function works around only applies to the first set of page-mapped registers; other pages can be written without locking. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21sfc: Remove unused private PCI register definitionsBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21sfc: Work around unreliable legacy interrupt statusBen Hutchings
In rare cases, reading the legacy interrupt status register can acknowledge an event queue whose attention flag has not yet been set in the register. Until we service this event queue it will not generate any more interrupts. Therefore, as a secondary check, poll the next slot in each active event queue whose flag is not set. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21sfc: Pad packets to 33 bytes to prevent TX packet parser lockupBen Hutchings
The packet parser used in the TX data path for locating checksum fields can lose synchronisation with the TX queue manager when handling packets that look like IPv4 but are too short (17-32 bytes). Work around this by padding to 33 bytes. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21dsa: add switch chip cascading supportLennert Buytenhek
The initial version of the DSA driver only supported a single switch chip per network interface, while DSA-capable switch chips can be interconnected to form a tree of switch chips. This patch adds support for multiple switch chips on a network interface. An example topology for a 16-port device with an embedded CPU is as follows: +-----+ +--------+ +--------+ | |eth0 10| switch |9 10| switch | | CPU +----------+ +-------+ | | | | chip 0 | | chip 1 | +-----+ +---++---+ +---++---+ || || || || ||1000baseT ||1000baseT ||ports 1-8 ||ports 9-16 This requires a couple of interdependent changes in the DSA layer: - The dsa platform driver data needs to be extended: there is still only one netdevice per DSA driver instance (eth0 in the example above), but each of the switch chips in the tree needs its own mii_bus device pointer, MII management bus address, and port name array. (include/net/dsa.h) The existing in-tree dsa users need some small changes to deal with this. (arch/arm) - The DSA and Ethertype DSA tagging modules need to be extended to use the DSA device ID field on receive and demultiplex the packet accordingly, and fill in the DSA device ID field on transmit according to which switch chip the packet is heading to. (net/dsa/tag_{dsa,edsa}.c) - The concept of "CPU port", which is the switch chip port that the CPU is connected to (port 10 on switch chip 0 in the example), needs to be extended with the concept of "upstream port", which is the port on the switch chip that will bring us one hop closer to the CPU (port 10 for both switch chips in the example above). - The dsa platform data needs to specify which ports on which switch chips are links to other switch chips, so that we can enable DSA tagging mode on them. (For inter-switch links, we always use non-EtherType DSA tagging, since it has lower overhead. The CPU link uses dsa or edsa tagging depending on what the 'root' switch chip supports.) This is done by specifying "dsa" for the given port in the port array. - The dsa platform data needs to be extended with information on via which port to reach any given switch chip from any given switch chip. This info is specified via the per-switch chip data struct ->rtable[] array, which gives the nexthop ports for each of the other switches in the tree. For the example topology above, the dsa platform data would look something like this: static struct dsa_chip_data sw[2] = { { .mii_bus = &foo, .sw_addr = 1, .port_names[0] = "p1", .port_names[1] = "p2", .port_names[2] = "p3", .port_names[3] = "p4", .port_names[4] = "p5", .port_names[5] = "p6", .port_names[6] = "p7", .port_names[7] = "p8", .port_names[9] = "dsa", .port_names[10] = "cpu", .rtable = (s8 []){ -1, 9, }, }, { .mii_bus = &foo, .sw_addr = 2, .port_names[0] = "p9", .port_names[1] = "p10", .port_names[2] = "p11", .port_names[3] = "p12", .port_names[4] = "p13", .port_names[5] = "p14", .port_names[6] = "p15", .port_names[7] = "p16", .port_names[10] = "dsa", .rtable = (s8 []){ 10, -1, }, }, }, static struct dsa_platform_data pd = { .netdev = &foo, .nr_switches = 2, .sw = sw, }; Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Gary Thomas <gary@mlbassoc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21dsa: add support for the Marvell 88E6095/6095F switch chipsLennert Buytenhek
Add support for the Marvell 88E6095/6095F switch chips. These chips are similar to the 88e6131, so we can add the support to mv88e6131.c easily. Thanks to Gary Thomas <gary@mlbassoc.com> and Jesper Dangaard Brouer <hawk@diku.dk> for testing various patches. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Gary Thomas <gary@mlbassoc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21dsa: set ->iflink on slave interfaces to the ifindex of the parentLennert Buytenhek
..so that we can parse the DSA topology from 'ip link' output: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 4: lan1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue 5: lan2@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue 6: lan3@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue 7: lan4@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21eql: fix non-constant printk warningStephen Hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21atm: fix non-const printk argumentStephen Hemminger
Change printk() argument to fix compiler warning. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21ipx: use constant for strings and desciptorStephen Hemminger
Fix compiler warning about non-const format string. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21snap: use const for descriptorStephen Hemminger
Protocols should be able to use constant value for the descriptor. Minor whitespace cleanup as well Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21igb: cleanup tx dma so map & unmap use matching callsAlexander Duyck
The igb driver was using map_single to map the skbs and then unmap_page to unmap them. This update changes that so instead uses skb_dma_map and skb_dma_unmap. In addition the next_to_watch member of the buffer_info struct was being set uneccesarily. I removed the spots where it was set without being needed. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21igb: rework igb_set_multi so that vfs are properly updatedAlexander Duyck
Currently if there are no multicast addresses programmed into the PF then the VFs cannot have their multicast filters reset. This change makes it so the code path that updates vf multicast is always called along with the pf updates. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21igb: update driver to use setup_timer functionAlexander Duyck
igb was previously setting up all of the timer members itself. It is easier to just call setup_timer and reduce the calls to one line. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21igb: remove IGB_DESC_UNUSED since it is better handled by a function callAlexander Duyck
This patch removes IGB_DESC_UNUSED and replaces it with a function call instead in order to cleanup some of the ugliness introduced by the macro. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21igb: allow tx of pre-formatted vlan tagged packetsArthur Jones
When the 82575 is fed 802.1q packets, it chokes with an error of the form: igb 0000:08:00.1 partial checksum but proto=81! As the logic there was not smart enough to look into the vlan header to pick out the encapsulated protocol. There are times when we'd like to send these packets out without having to configure a vlan on the interface. Here we check for the vlan tag and allow the packet to go out with the correct hardware checksum. Thanks to Kand Ly <kand@riverbed.com> for discovering the issue and the coming up with a solution. This patch is based upon his work. Signed-off-by: Arthur Jones <ajones@riverbed.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21spider_net: Convert to net_device_ops.Yang Hongyang
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21powerpc 4xx EMAC driver: device name reported on timeout is not correctMikhail Zolotaryov
Hi, IBM EMAC driver performs device reset (drivers/net/ibm_newemac/core.c: emac_probe() -> emac_init_phy() -> emac_reset()) before registering appropriate net_device (emac_probe() -> register_netdev()), so net_device name contains raw format string during EMAC reset ("eth%d"). If the case of reset timeout, emac_report_timeout_error() function is called to report an error. The problem is this function uses net_device name to report device related, which is not correct, as a result in the kernel log buffer we see: eth%d: reset timeout The solution is to print device_node full_name instead. After applying the patch proposed, error string is like the following: /plb/opb/ethernet@ef600e00: reset timeout Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21net: remove useless prefetch() callEric Dumazet
There is no gain using prefetch() in dev_hard_start_xmit(), since we already had to read ops->ndo_select_queue pointer in dev_pick_tx(), and both pointers are probably located in the same cache line. This prefetch call slows down fast path because of a stall in address computation. Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21sctp: Clean up TEST_FRAME hacks.Vlad Yasevich
Remove 2 TEST_FRAME hacks that are no longer needed. These allowed sctp regression tests to compile before, but are no longer needed. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21ixgbe: fix select_queue managementStephen Hemminger
Convert ixgbe to use net_device_ops properly. Rather than changing the select_queue function pointer just check the flag. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21skb: expose and constify hash primitivesStephen Hemminger
Some minor changes to queue hashing: 1. Use const on accessor functions 2. Export skb_tx_hash for use in drivers (see ixgbe) Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21atm: lec use dev_change_mtuStephen Hemminger
Rather than calling device pointer directly (which is incorrect with net_device_ops), use the standard dev_change_mtu. Compile tested only. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21net/*: use linux/kernel.h swap()Ilpo Järvinen
tcp_sack_swap seems unnecessary so I pushed swap to the caller. Also removed comment that seemed then pointless, and added include when not already there. Compile tested. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21netrom: zero length frame filtering in NetRomBernard Pidoux
A zero length frame filter was recently introduced in ROSE protocole. Previous commit makes the same at AX25 protocole level. This patch has the same purpose for NetRom protocole. The reason is that empty frames have no meaning in NetRom protocole. Signed-off-by: Bernard Pidoux <f6bvp@amsat.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21ax25: zero length frame filtering in AX25Bernard Pidoux
In previous commit 244f46ae6e9e18f6fc0be7d1f49febde4762c34b was introduced a zero length frame filter for ROSE protocole. This patch has the same purpose at AX25 frame level for the same reason. Empty frames have no meaning in AX25 protocole. Signed-off-by: Bernard Pidoux <f6bvp@amsat.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21ax25: SOCK_DEBUG message simplificationBernard Pidoux
This patch condenses two debug messages in one. Signed-off-by: Bernard Pidoux <f6bvp@amsat.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21fsl_pq_mdio: Revive Gianfar TBI PHY supportAnton Vorontsov
commit 1577ecef766650a57fceb171acee2b13cbfaf1d3 ("netdev: Merge UCC and gianfar MDIO bus drivers") broke the TSEC TBI PHY support: the driver now refuses to probe TBI MDIO buses as it doesn't know about "fsl,gianfar-tbi" compatible entry, and thus _probe() fails with -ENODEV status. Fix this by adding "fsl,gianfar-tbi" to the list of known Gianfar MDIO buses. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21ipv6: reorder struct inet6_ifaddr to remove padding on 64 bit buildsRichard Kennedy
reorder struct inet6_ifaddr to remove padding on 64 bit builds remove 8 bytes of padding so inet6_ifaddr becomes 192 bytes & fits into a smaller slab. Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21gianfar: Fix build with CONFIG_PM enabledAnton Vorontsov
commit 4826857f1bf07f9c0f1495e9b05d125552c88a85 ("gianfar: pass the proper dev to DMA ops") introduced this build breakage: CC drivers/net/gianfar.o drivers/net/gianfar.c: In function 'gfar_suspend': drivers/net/gianfar.c:552: error: 'struct gfar_private' has no member named 'dev' drivers/net/gianfar.c: In function 'gfar_resume': drivers/net/gianfar.c:601: error: 'struct gfar_private' has no member named 'dev' make[2]: *** [drivers/net/gianfar.o] Error 1 Fix this by converting suspend and resume routines to use gfar_private->ndev. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21e100: add support for 82552 10/100 adapterBruce Allan
This patch enables support for the new Intel 82552 adapter (new PHY paired with the existing MAC in the ICH7 chipset). No new features are added to the driver, however there are minor changes due to updated registers and a few workarounds for hardware errata. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21Merge branch 'master' of git://git.infradead.org/~dwmw2/solos-2.6David S. Miller
2009-03-20e1000e: fixup merge errorArthur Jones
When merging into Jeff's tree: commit 5f66f208064f083aab5e55935d0575892e033b59 Author: Arthur Jones <ajones@riverbed.com> Date: Thu Mar 19 01:13:08 2009 +0000 e1000e: allow tx of pre-formatted vlan tagged packets We lost one line, this fixes that missing piece... Signed-off-by: Arthur Jones <ajones@riverbed.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/virtio_net.c
2009-03-20net: reorder struct Qdisc for better SMP performanceEric Dumazet
dev_queue_xmit() needs to dirty fields "state", "q", "bstats" and "qstats" On x86_64 arch, they currently span three cache lines, involving more cache line ping pongs than necessary, making longer holding of queue spinlock. We can reduce this to one cache line, by grouping all read-mostly fields at the beginning of structure. (Or should I say, all highly modified fields at the end :) ) Before patch : offsetof(struct Qdisc, state)=0x38 offsetof(struct Qdisc, q)=0x48 offsetof(struct Qdisc, bstats)=0x80 offsetof(struct Qdisc, qstats)=0x90 sizeof(struct Qdisc)=0xc8 After patch : offsetof(struct Qdisc, state)=0x80 offsetof(struct Qdisc, q)=0x88 offsetof(struct Qdisc, bstats)=0xa0 offsetof(struct Qdisc, qstats)=0xac sizeof(struct Qdisc)=0xc0 Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20dnet: remove duplicated #includeHuang Weiyi
Removed duplicated #include in drivers/net/dnet.c. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20ixgbe: Fixup the watchdog interrupt scheduling on 82599Jesse Brandeburg
The watchdog will schedule an interrupt to help make sure queues are cleaned in the case when an interrupt is missed, most likely due to very high load. On 82599, there are extra interrupt registers to account for the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for 82598). These must be taken into account when performing this operation in the watchdog. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20ixgbe: Correctly report Wake On LAN for 82599 KX4 devicesPJ Waskiewicz
ethtool isn't reporting the support level of WoL for 82599 KX4 devices. While the device does support WoL, ethtool was never updated to properly report the level of support, nor will it allow ethtool to modify the type of packets to listen for. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20ixgbe: Fix PCI bus reporting on driver load for 82598 after 82599 mergePJ Waskiewicz
82598's PCI bus reporting on driver load was broken after 82599 merged. This results in incorrect reporting, and an erroneous warning message that the 82598 is in a PCIe slot that isn't fast enough to run 10GbE. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20ixgb: refactor tx path to use skb_dma_map/unmapAlexander Duyck
This code updates ixgb so that it can use the skb_dma_map/unmap functions to map the buffers. In addition it also updates the tx hang logic to use time_stamp instead of dma to determine if it has detected a tx hang. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20e1000e: allow tx of pre-formatted vlan tagged packetsArthur Jones
As with igb, when the e1000e driver is fed 802.1q packets with hardware checksum on, it chokes with an error of the form: checksum_partial proto=81! As the logic there was not smart enough to look into the vlan header to pick out the encapsulated protocol. There are times when we'd like to send these packets out without having to configure a vlan on the interface. Here we check for the vlan tag and allow the packet to go out wiht the correct hardware checksum. Thanks to Kand Ly <kand@riverbed.com> for discovering the issue and the coming up with a solution. This patch is based upon his work. Fixups from Stephen Hemminger <shemminger@vyatta.com> and Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Arthur Jones <ajones@riverbed.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Stephen Hemminger <shemminger@vyatta.com> CC: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20e1000e: fix dma error handling issuesAlexander Duyck
There were a few issues I noticed in e1000e. These include a double free of the skb if mapping fails, and the fact that context descriptors appear to be left in the descriptor ring after the failure. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20e1000e: add support for 82583 device idAlexander Duyck
Add device ID and related support for 82583 mac. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Radheka Godse <radheka.godse@intel.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20smsc9420: fix big endian rx checksum offloadSteve Glendinning
The cpu_to_le16 here looks suspicious to me, I don't think we need it because put_unaligned_le16 also does this. I don't currently have any big endian hardware with a PCI bus available to test on, so I haven't been able to verify this. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20sunvnet: Convert to net_device_ops.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19smsc911x: allow setting of mac addressSteve Glendinning
This patch replaces the generic eth_mac_addr function with one that also updates the hardware mac address registers. It also renames the existing smsc911x_set_mac_address function to smsc911x_hw_set_mac_address for clarity. Newer LAN911x and all LAN921x devices also support changing the mac address while the device is running, which is useful for some bonding modes. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19smsc911x: replace print_mac with %pMSteve Glendinning
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19smsc911x: define status word positions as constantsSteve Glendinning
The vast majority of bit constants in this driver are defined in the header file, but TX and RX status word bits are not. This patch (which should make no functional change) defines these, to make the driver slightly more readable. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-23 22:33:41 +0000