aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-07-02netxen: avoid frequent firmware resetDhananjay Phadke
Restrict firmware reset to following cases - o chip rev is NX2031 (firmare doesn't support heartbit). o firmware is dead. o previous attempt to init firmware had failed. o we have got newer file firmware. This speeds up module load tremendously (by upto 8 sec), also avoids downtime for NCSI (management) pass-thru traffic. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02netxen: fix the version code macroDhananjay Phadke
Correct firmware encoding is 8 bit major, 8 bit minor and 16 bit subversion. Flash has sizes rightly set, but original driver submission messed it leaving 16 bit major and 8 bit subversion. Also fix a infinite loop when cut-thru file firmware is invalid. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02gigaset: drop pointless checkTilman Schmidt
Drop a sanity check which doesn't serve any useful purpose anymore. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02gigaset: accept connection establishment messages in any orderTilman Schmidt
ISDN connection setup failed if the "connection active" and "B channel up" messages from the device arrived in a different order than expected. Modify the state machine to accept them in any order. Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> CC: stable <stable@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30Revert "ipv4: arp announce, arp_proxy and windows ip conflict verification"Eric W. Biederman
This reverts commit 73ce7b01b4496a5fbf9caf63033c874be692333f. After discovering that we don't listen to gratuitious arps in 2.6.30 I tracked the failure down to this commit. The patch makes absolutely no sense. RFC2131 RFC3927 and RFC5227. are all in agreement that an arp request with sip == 0 should be used for the probe (to prevent learning) and an arp request with sip == tip should be used for the gratitous announcement that people can learn from. It appears the author of the broken patch got those two cases confused and modified the code to drop all gratuitous arp traffic. Ouch! Cc: stable@kernel.org Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30igb: return PCI_ERS_RESULT_DISCONNECT on permanent errorAlexander Duyck
PCI drivers that implement the io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for igb. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30e1000e: io_error_detected callback should return PCI_ERS_RESULT_DISCONNECTMike Mason
on permanent failure PCI drivers that implement the io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This state is not checked in many of the network drivers. This patch fixes the omission in the e1000e driver. Signed-off-by: Mike Mason <mmlnx@us.ibm.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30e1000: return PCI_ERS_RESULT_DISCONNECT on permanent errorAndre Detsch
PCI drivers that implement the io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This state is not checked in many of the network drivers. The patch fixes the omission in the e1000 driver. Based on Mike Mason's similar patch for e1000e. Signed-off-by: Andre Detsch <adetsch@br.ibm.com> CC: Mike Mason <mmlnx@us.ibm.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30e1000: fix unmap bugJesse Brandeburg
as reported by kerneloops.org [ 121.781161] ------------[ cut here ]------------ [ 121.781171] WARNING: at lib/dma-debug.c:793 check_unmap+0x14e/0x577() [ 121.781173] Hardware name: S5520HC [ 121.781177] e1000 0000:0a:00.0: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x00000001d688b0fa] [size=1522 bytes] [ 121.781180] Modules linked in: e1000 mdio dca [last unloaded: ixgbe] [ 121.781187] Pid: 4793, comm: bash Tainted: P 2.6.30-master-06161113 #3 [ 121.781190] Call Trace: [ 121.781195] [<ffffffff8123056f>] ? check_unmap+0x14e/0x577 [ 121.781201] [<ffffffff81057a19>] warn_slowpath_common+0x77/0x8f [ 121.781205] [<ffffffff81057ae1>] warn_slowpath_fmt+0x9f/0xa1 [ 121.781212] [<ffffffff81477ce2>] ? _spin_lock_irqsave+0x3f/0x49 [ 121.781216] [<ffffffff8122fa97>] ? get_hash_bucket+0x28/0x33 [ 121.781220] [<ffffffff8123056f>] check_unmap+0x14e/0x577 [ 121.781225] [<ffffffff810e4f48>] ? check_bytes_and_report+0x38/0xcb [ 121.781230] [<ffffffff81230bbf>] debug_dma_unmap_page+0x80/0x92 [ 121.781234] [<ffffffff8122e549>] ? unmap_single+0x1a/0x4e [ 121.781239] [<ffffffff813901e1>] ? __kfree_skb+0x74/0x78 [ 121.781250] [<ffffffffa00662ef>] pci_unmap_single+0x64/0x6d [e1000] [ 121.781259] [<ffffffffa0066344>] e1000_clean_rx_ring+0x4c/0xbf [e1000] [ 121.781268] [<ffffffffa00663df>] e1000_clean_all_rx_rings+0x28/0x36 [e1000] [ 121.781277] [<ffffffffa0067464>] e1000_down+0x138/0x141 [e1000] [ 121.781286] [<ffffffffa00681c2>] __e1000_shutdown+0x6b/0x198 [e1000] [ 121.781296] [<ffffffffa0068405>] e1000_suspend+0x17/0x50 [e1000] [ 121.781301] [<ffffffff81237665>] pci_legacy_suspend+0x3b/0xbe [ 121.781305] [<ffffffff81237bc6>] pci_pm_suspend+0x3e/0xf1 [ 121.781310] [<ffffffff812eaf1c>] pm_op+0x57/0xde [ 121.781314] [<ffffffff812eb444>] dpm_suspend_start+0x31e/0x470 [ 121.781319] [<ffffffff810877da>] suspend_devices_and_enter+0x3e/0x1a2 [ 121.781323] [<ffffffff81087a0f>] enter_state+0xd1/0x127 [ 121.781327] [<ffffffff8108717a>] state_store+0xa7/0xc9 [ 121.781332] [<ffffffff81221843>] kobj_attr_store+0x17/0x19 [ 121.781336] [<ffffffff8113c01e>] sysfs_write_file+0xe5/0x121 [ 121.781341] [<ffffffff810ed165>] vfs_write+0xab/0x105 [ 121.781344] [<ffffffff810ed279>] sys_write+0x47/0x6d [ 121.781349] [<ffffffff81027aab>] system_call_fastpath+0x16/0x1b [ 121.781352] ---[ end trace 97bacaaac2ed7786 ]--- Fix is to correctly zero out internal ->dma value when unmapping and make sure never to unmap unless there specifically was a mapping done. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30igb: fix unmap length bugJesse Brandeburg
driver was mixing NET_IP_ALIGN count bytes in map/unmap calls unevenly. Only map the bytes that the hardware might dma into also fix unmap related bug where ->dma was not being cleared after unmap Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30ixgbe: fix unmap length bugJesse Brandeburg
This patch addresses three WARN_ON statements from DMA-API debug code ixgbe is mapping more than it unmaps, reduce the length of the map call and remove the "used once" local variable. found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate for -stable. in addition, fix missing ->dma = 0 after unmap to prevent double free with pci_unmap_single and lastly, don't unmap (half) pages that aren't mapped. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30ixgbe: Fix link capabilities during adapter resetsMallikarjuna R Chilakala
Adapter link advertisement capabilities were not persistent during adapter resets. While configuring multispeed fiber link check for phy autoneg_advertised settings before overwriting with default link capabilities Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30ixgbe: Fix device capabilities of 82599 single speed fiber NICs.Mallikarjuna R Chilakala
82599 single speed fiber modules only support 10G/Full. Return proper device capabilities while querrying the adapter and error while changing device advertisement/speed/duplex capabilities. Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30ixgbe: Fix SFP log messagesDon Skidmore
We had a wide range of log messages for the same sort of SFP failure. This patch makes them all more similar and less confusing along with converting them to dev_err. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30usbnet: Remove private stats structureHerbert Xu
Now that nothing uses the private stats structure we can remove it. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30usbnet: Use netdev stats structureHerbert Xu
Now that netdev has its own stats structure we should use that instead. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30smsc95xx: Use netdev stats structureHerbert Xu
Now that netdev has its own stats structure we should use that instead. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30rndis_host: Use netdev stats structureHerbert Xu
Now that netdev has its own stats structure we should use that instead. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30net1080: Use netdev stats structureHerbert Xu
Now that netdev has its own stats structure we should use that instead. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30dm9601: Use netdev stats structureHerbert Xu
Now that netdev has its own stats structure we should use that instead. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30cdc_eem: Use netdev stats structureHerbert Xu
Now that netdev has its own stats structure we should use that instead. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30ipv4: Fix fib_trie rebalancing, part 3Jarek Poplawski
Alas current delaying of freeing old tnodes by RCU in trie_rebalance is still not enough because we can free a top tnode before updating a t->trie pointer. Reported-by: Pawel Staszewski <pstaszewski@itcare.pl> Tested-by: Pawel Staszewski <pstaszewski@itcare.pl> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30bnx2x: Fix the behavior of ethtool when ONBOOT=noNaohiro Ooiwa
This is the same fix as commit 7959ea254ed18faee41160b1c50b3c9664735967 ("bnx2: Fix the behavior of ethtool when ONBOOT=no"), but for bnx2x: -------------------- When configure in ifcfg-eth* is ONBOOT=no, the behavior of ethtool command is wrong. # grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2 ONBOOT=no # ethtool eth2 | tail -n1 Link detected: yes I think "Link detected" should be "no". -------------------- Signed-off-by: Naohiro Ooiwa <nooiwa@miraclelinux.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29sctp: xmit sctp packet always return no route errorWei Yongjun
Commit 'net: skb->dst accessors'(adf30907d63893e4208dfe3f5c88ae12bc2f25d5) broken the sctp protocol stack, the sctp packet can never be sent out after Eric Dumazet's patch, which have typo in the sctp code. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Vlad Yasevich <vladisalv.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29net/irda: convert bfin_sir to net_device_opsGraf Yang
Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29xfrm: use xfrm_addr_cmp() instead of compare addresses directlyWei Yongjun
Clean up to use xfrm_addr_cmp() instead of compare addresses directly. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29tcp: Do not tack on TSO data to non-TSO packetHerbert Xu
If a socket starts out on a non-TSO route, and then switches to a TSO route, then we will tack on data to the tail of the tx queue even if it started out life as non-TSO. This is suboptimal because all of it will then be copied and checksummed unnecessarily. This patch fixes this by ensuring that skb->ip_summed is set to CHECKSUM_PARTIAL before appending extra data beyond the MSS. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29tcp: Stop non-TSO packets morphing into TSOHerbert Xu
If a socket starts out on a non-TSO route, and then switches to a TSO route, then the tail on the tx queue can morph into a TSO packet, causing mischief because the rest of the stack does not expect a partially linear TSO packet. This patch fixes this by ensuring that skb->ip_summed is set to CHECKSUM_PARTIAL before declaring a packet as TSO. Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29Merge branch 'for-linus' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/lowpan/lowpan
2009-06-29Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
2009-06-29nl802154: add module license and descriptionDmitry Eremin-Solenikov
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
2009-06-29nl802154: fix Oops in ieee802154_nl_get_devDmitry Eremin-Solenikov
ieee802154_nl_get_dev() lacks check for the existance of the device that was returned by dev_get_XXX, thus resulting in Oops for non-existing devices. Fix it. Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
2009-06-29MAINTAINERS: ieee802154 lists are moderated for non-subscribers.Dmitry Eremin-Solenikov
Note that our mailing list is moderated for non-subscribers. Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
2009-06-29netfilter: xtables: conntrack match revision 2Jan Engelhardt
As reported by Philip, the UNTRACKED state bit does not fit within the 8-bit state_mask member. Enlarge state_mask and give status_mask a few more bits too. Reported-by: Philip Craig <philipc@snapgear.com> References: http://markmail.org/thread/b7eg6aovfh4agyz7 Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Patrick McHardy <kaber@trash.net>
2009-06-29netfilter: headers_check fix: linux/netfilter/xt_osf.hJaswinder Singh Rajput
fix the following 'make headers_check' warnings: usr/include/linux/netfilter/xt_osf.h:40: found __[us]{8,16,32,64} type without #include <linux/types.h> Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
2009-06-29netfilter: tcp conntrack: fix unacknowledged data detection with NATPatrick McHardy
When NAT helpers change the TCP packet size, the highest seen sequence number needs to be corrected. This is currently only done upwards, when the packet size is reduced the sequence number is unchanged. This causes TCP conntrack to falsely detect unacknowledged data and decrease the timeout. Fix by updating the highest seen sequence number in both directions after packet mangling. Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl> Signed-off-by: Patrick McHardy <kaber@trash.net>
2009-06-28be2net: Fix to avoid a crash seen on PPC with LRO and Jumbo frames.Ajit Khaparde
While testing the driver on PPC, we ran into a crash with LRO, Jumbo frames. With CONFIG_PPC_64K_PAGES configured (a default in PPC), MAX_SKB_FRAGS drops to 3 and we were crossing the array limits on skb_shinfo(skb)->frags[]. Now we coalesce the frags from the same physical page into one slot in skb_shinfo(skb)->frags[] and go to the next index when the frag is from different physical page. This patch is against the net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26gro: Flush GRO packets in napi_disable_pending pathHerbert Xu
When NAPI is disabled while we're in net_rx_action, we end up calling __napi_complete without flushing GRO packets. This is a bug as it would cause the GRO packets to linger, of course it also literally BUGs to catch error like this :) This patch changes it to napi_complete, with the obligatory IRQ reenabling. This should be safe because we've only just disabled IRQs and it does not materially affect the test conditions in between. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26inet: Call skb_orphan before tproxy activatesHerbert Xu
As transparent proxying looks up the socket early and assigns it to the skb for later processing, we must drop any existing socket ownership prior to that in order to distinguish between the case where tproxy is active and where it is not. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26mac80211: Use rcu_barrier() on unload.Jesper Dangaard Brouer
The mac80211 module uses rcu_call() thus it should use rcu_barrier() on module unload. The rcu_barrier() is placed in mech.c ieee80211_stop_mesh() which is invoked from ieee80211_stop() in case vif.type == NL80211_IFTYPE_MESH_POINT. Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26sunrpc: Use rcu_barrier() on unload.Jesper Dangaard Brouer
The sunrpc module uses rcu_call() thus it should use rcu_barrier() on module unload. Have not verified that the possibility for new call_rcu() callbacks has been disabled. As a hint for checking, the functions calling call_rcu() (unx_destroy_cred and generic_destroy_cred) are registered as crdestroy function pointer in struct rpc_credops. Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26bridge: Use rcu_barrier() instead of syncronize_net() on unload.Jesper Dangaard Brouer
When unloading modules that uses call_rcu() callbacks, then we must use rcu_barrier(). This module uses syncronize_net() which is not enough to be sure that all callback has been completed. Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26ipv6: Use rcu_barrier() on module unload.Jesper Dangaard Brouer
The ipv6 module uses rcu_call() thus it should use rcu_barrier() on module unload. Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26decnet: Use rcu_barrier() on module unload.Jesper Dangaard Brouer
The decnet module unloading as been disabled with a '#if 0' statement, because it have had issues. We add a rcu_barrier() anyhow for correctness. The maintainer (Chrissie Caulfield) will look into the unload issue when time permits. Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Chrissie Caulfield <christine.caulfield@googlemail.com> Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26sky2: Fix checksum endiannessAnton Vorontsov
sky2 driver on PowerPC targets floods kernel log with following errors: eth1: hw csum failure. Call Trace: [ef84b8a0] [c00075e4] show_stack+0x50/0x160 (unreliable) [ef84b8d0] [c02fa178] netdev_rx_csum_fault+0x3c/0x5c [ef84b8f0] [c02f6920] __skb_checksum_complete_head+0x7c/0x84 [ef84b900] [c02f693c] __skb_checksum_complete+0x14/0x24 [ef84b910] [c0337e08] tcp_v4_rcv+0x4c8/0x6f8 [ef84b940] [c031a9c8] ip_local_deliver+0x98/0x210 [ef84b960] [c031a788] ip_rcv+0x38c/0x534 [ef84b990] [c0300338] netif_receive_skb+0x260/0x36c [ef84b9c0] [c025de00] sky2_poll+0x5dc/0xcf8 [ef84ba20] [c02fb7fc] net_rx_action+0xc0/0x144 The NIC is Yukon-2 EC chip revision 1. Converting checksum field from le16 to CPU byte order fixes the issue. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25mdio add missing GPL flagNicolas Reinecke
Add missing GPL flag and description. mdio: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint Signed-off-by: Nicolas Reinecke <nr <at> das-labor.org> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25sh_eth: remove redundant test on unsignedroel kluin
Unsigned boguscnt cannot be less than 0. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25fsl_pq_mdio: Fix fsl_pq_mdio to work with modulesIonut Nicu
This patch fixes the case when ucc_geth or gianfar are compiled as modules. Without this patch the call to phy_connect() fails. Signed-off-by: Ionut Nicu <ionut.nicu@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25ipv6: avoid wraparound for expired preferred lifetimeJens Rosenboom
Avoid showing wrong high values when the preferred lifetime of an address is expired. Signed-off-by: Jens Rosenboom <me@jayr.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25tcp: missing check ACK flag of received segment in FIN-WAIT-2 stateWei Yongjun
RFC0793 defined that in FIN-WAIT-2 state if the ACK bit is off drop the segment and return[Page 72]. But this check is missing in function tcp_timewait_state_process(). This cause the segment with FIN flag but no ACK has two diffent action: Case 1: Node A Node B <------------- FIN,ACK (enter FIN-WAIT-1) ACK -------------> (enter FIN-WAIT-2) FIN -------------> discard (move sk to tw list) Case 2: Node A Node B <------------- FIN,ACK (enter FIN-WAIT-1) ACK -------------> (enter FIN-WAIT-2) (move sk to tw list) FIN -------------> <------------- ACK This patch fixed the problem. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-14 23:19:10 +0000