aboutsummaryrefslogtreecommitdiff
path: root/arch/powerpc/boot
AgeCommit message (Collapse)Author
2009-11-11powerpc/85xx: Add power management support for MPC85xxMDS boardsAnton Vorontsov
- Add power management controller nodes; - Add interrupts for RTC nodes, the RTC interrupt may be used as a wakeup source; - Add sleep properties (DEVDISR bit mask) and sleep-nexus nodes. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-11-11powerpc/85xx: Added P1020RDB Platform support.Poonam Aggrwal
P1020 is another member of Freescale QorIQ series of processors. It is an e500 based dual core SOC. Being a scaled down version of P2020 it has following differences from P2020: - 533MHz - 800MHz core frequency. - 256Kbyte L2 cache - Ethernet controllers with classification capabilities(new controller). From board perspective P1020RDB is same as P2020RDB. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-11-11powerpc/85xx: Create dts for each core in CAMP mode for P2020RDBPoonam Aggrwal
This patch creates the dts files for each core and splits the devices between the two cores for P2020RDB. core0 has memory, L2, i2c, spi, dma1, usb, eth0, eth1, crypto, global-util, pci0, core1 has L2, dma2, eth0, pci1, msi. MPIC is shared between two cores but each core will protect its interrupts from other core by using "protected-sources" of mpic. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-11-05powerpc/83xx: Fix u-boot partion size for MPC8377E-WLAN boardsAnton Vorontsov
u-boot partition size should be 0x80000 (512 KB), not 0x8000 (32 KB). Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-11-05powerpc/85xx: Fix USB GPIOs for MPC8569E-MDS boardsAnton Vorontsov
This patch fixes USB GPIOs numbers for MPC8569E-MDS boards, plus according to the latest HW Getting Started Guide (rev 3.3, pilot boards), USB "POWER" GPIO polarity has changed, it is no longer inverted. This patch makes USB Host somewhat work on pilot boards, though there are still some problems with determining devices speed and long bulk transfers. Reported-by: Liu Yu <Yu.Liu@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-11-05powerpc/85xx: sbc8548 - fixup of PCI-e related DTS fieldsPaul Gortmaker
The PCI-e addressing was originally patterned of the MPC8548CDS which has PCI1, PCI2, and PCI-e. Since this board only has PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS board. This does that by cutting the PCI/PCI-e I/O sizes from 16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000 (the hole where PCI2 I/O would have been). This also fixes a typo where an extra zero made an 8MB range a 128MB range, removes the hole left by PCI2 from the aliases, and sets the clocks to match the oscillators that are actually on the board. With accompanying u-boot updates, PCI-e has been validated with both a sky2 card (1148:9e00) and an e1000 card (8086:108b). Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-11-04powerpc/44x: Enable 64bit (>= 4GB) memory size in Katmai dtsStefan Roese
Additionally to increasing #size-cells to in the root node, we also need to explicitly define the ranges property in the plb node, because of the different #size-cells between child and parent. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-11-04powerpc/4xx: Add 16K FIFO size DTS entries on supported platformsDave Mitchell
Adding tx/rx-fifo-size-gige to EMAC fields for evaluation kit DTS files where appropriate. Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com> Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com> Acked-by: Victor Gallardo <vgallardo@appliedmicro.com> Acked-by: Loc Ho <lho@appliedmicro.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-10-15powerpc/boot/dts: drop obsolete 'fsl5200-clocking'Wolfram Sang
The 'fsl5200-clocking'-property was dropped since 0d1cde235874b00905bce23f659690d060ebf475. Remove all occurences in dts-files. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-10-15mpc5200: support for the MAN mpc5200 based board mucmc52Heiko Schocher
- serial Console on PSC1 - 64MB SDRAM - MTD CFI Flash - Ethernet FEC - IDE support Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-10-15mpc5200: support for the MAN mpc5200 based board uc101Heiko Schocher
- serial Console on PSC1 - 64MB SDRAM - MTD CFI Flash - Ethernet FEC - I2C with PCF8563 and Temp. Sensor ADM9240 - IDE support Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-09-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-nextLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (30 commits) Use macros for .data.page_aligned section. Use macros for .bss.page_aligned section. Use new __init_task_data macro in arch init_task.c files. kbuild: Don't define ALIGN and ENTRY when preprocessing linker scripts. arm, cris, mips, sparc, powerpc, um, xtensa: fix build with bash 4.0 kbuild: add static to prototypes kbuild: fail build if recordmcount.pl fails kbuild: set -fconserve-stack option for gcc 4.5 kbuild: echo the record_mcount command gconfig: disable "typeahead find" search in treeviews kbuild: fix cc1 options check to ensure we do not use -fPIC when compiling checkincludes.pl: add option to remove duplicates in place markup_oops: use modinfo to avoid confusion with underscored module names checkincludes.pl: provide usage helper checkincludes.pl: close file as soon as we're done with it ctags: usability fix kernel hacking: move STRIP_ASM_SYMS from General gitignore usr/initramfs_data.cpio.bz2 and usr/initramfs_data.cpio.lzma kbuild: Check if linker supports the -X option kbuild: introduce ld-option ... Fix trivial conflict in scripts/basic/fixdep.c
2009-09-23powerpc: introduce and document sdhci,wp-inverted property for eSDHCAnton Vorontsov
eSDHC block in MPC837x SOCs reports inverted write-protect state, soon sdhci-of driver will look for sdhci,wp-inverted properties to decide whether apply a specific quirk. So, document the property and add it to device tree source files. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Pierre Ossman <pierre@ossman.eu> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: David Vrabel <david.vrabel@csr.com> Cc: Ben Dooks <ben@fluff.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-20kbuild: use INSTALLKERNEL to select customized installkernel scriptSam Ravnborg
Replace the use of CROSS_COMPILE to select a customized installkernel script with the possibility to set INSTALLKERNEL to select a custom installkernel script when running make: make INSTALLKERNEL=arm-installkernel install With this patch we are now more consistent across different architectures - they did not all support use of CROSS_COMPILE. The use of CROSS_COMPILE was a hack as this really belongs to gcc/binutils and the installkernel script does not change just because we change toolchain. The use of CROSS_COMPILE caused troubles with an upcoming patch that saves CROSS_COMPILE when a kernel is built - it would no longer be installable. [Thanks to Peter Z. for this hint] This patch undos what Ian did in commit: 0f8e2d62fa04441cd12c08ce521e84e5bd3f8a46 ("use ${CROSS_COMPILE}installkernel in arch/*/boot/install.sh") The patch has been lightly tested on x86 only - but all changes looks obvious. Acked-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Mike Frysinger <vapier@gentoo.org> [blackfin] Acked-by: Russell King <linux@arm.linux.org.uk> [arm] Acked-by: Paul Mundt <lethal@linux-sh.org> [sh] Acked-by: "H. Peter Anvin" <hpa@zytor.com> [x86] Cc: Ian Campbell <icampbell@arcom.com> Cc: Tony Luck <tony.luck@intel.com> [ia64] Cc: Fenghua Yu <fenghua.yu@intel.com> [ia64] Cc: Hirokazu Takata <takata@linux-m32r.org> [m32r] Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k] Cc: Kyle McMartin <kyle@mcmartin.ca> [parisc] Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> [powerpc] Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390] Cc: Thomas Gleixner <tglx@linutronix.de> [x86] Cc: Ingo Molnar <mingo@redhat.com> [x86] Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2009-08-31powerpc/405ex: support cuImage via included dtbTiejun Chen
To support cuImage, we need to initialize the required sections and ensure that it is built. Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-08-31powerpc/405ex: provide necessary fixup function to support cuImageTiejun Chen
For cuImage format it's necessary to provide clock fixups since u-boot will not pass necessary clock frequency into the dtb included into cuImage so we implement the clock fixups as defined in the technical documentation for the board and update header file with the basic register definitions. Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-08-31powerpc/40x: Add support for the ESTeem 195E (PPC405EP) SBCSolomon Peachy
This patch adds support for the ESTeem 195E Hotfoot SBC. There are several variants of the SBC deployed, single/dual ethernet+serial, and also 4MB/8MB flash variations. In the interest of having a single kernel image boot on all boards, the cuboot shim detects the differences and mangles the DTS tree appropriately. With the exception of the CF interface that was never populated on production boards, this code/DTS supports all boardpop options. Signed-off-by: Solomon Peachy <solomon@linux-wlan.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-08-31powerpc/44x: Add Eiger AMCC (AppliedMicro) PPC460SX evaluation board support.fkan@amcc.com
This patch adds support for the AMCC (AppliedMicro) PPC460SX Eiger evaluation board. Signed-off-by: Tai Tri Nguyen <ttnguyen@amcc.com> Acked-by: Feng Kan <fkan@amcc.com> Acked-by: Tirumala Marri <tmarri@amcc.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-08-31powerpc/44x: Update Arches dtsStefan Roese
This patch adds some nodes to the AMCC Arches dts: - L2 cache support - NOR FLASH mapping with default partitioning - I2C HWMON device (AD7414) Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-08-25powerpc/85xx: Add QE USB support for MPC8569E-MDS boardsAnton Vorontsov
- Add gpio-controller node for BCSR17, it is used to control USB speed and VBUS; - Add timer node for QE GTM, needed for USB host; - Add usb node itself; - Add some probing code for BCSR GPIOs. NOTE: QE USB doesn't work on prototype boards, but should work on pilot boards if specs and schematics are correct, though we don't have the pilot boards to actually test it. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-25powerpc/82xx: Add CPM USB Gadget support for MPC8272ADS boardsAnton Vorontsov
- Add usb node; - Configure pins and clocks; - Enable USB function in BCSR. The support was successfully tested using serial and ethernet gadget drivers. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-25powerpc/85xx: Add eSDHC support for MPC8536DS boardsAnton Vorontsov
This patch simply adds sdhci node to the device tree. We specify clock-frequency manually, so that eSDHC will work without upgrading U-Boot. Though, that'll only work for default setup (1500 MHz) on new board revisions. For non-default setups, it's recommended to upgrade U-Boot, since it will fixup clock-frequency automatically. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-24powerpc/85xx: sbc8560 - remove "has-rstcr" from global utilities blockPaul Gortmaker
The earlier mpc8560 CPUs don't have the RSTCR at 0xe00b0 in the GUTS. The generic reboot code uses this tag to determine if it should be using the RSTCR for reboot, so remove it from the board definition. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-24powerpc/83xx: Fix incorrect PCI interrupt map in SBC834x DTSLiang Li
Allows interrupts to occur on the sbc834x. Currently PCI devices get assigned an incorrect IRQ and so the interrupt count never increases. This was tested with the 82546GB based dual port E1000 PCI-X NIC which uses two distinct IRQ lines on the one card. root@localhost:/root> cat /proc/interrupts | grep eth 17: 78 IPIC Level eth1 48: 27121 IPIC Level eth0 Signed-off-by: Liang Li <liang.li@windriver.com> Signed-off-by: Yang Shi <yang.shi@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-24powerpc/83xx: Add localbus node and MTD partitions for SBC834xLiang Li
There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x local bus, so add a localbus node in DTS with MTD partitions. The recent U-boot commit fe613cdd4eb moves u-boot to the beginning of flash, hence the legacy label on the partition at the end of flash. Signed-off-by: Liang Li <liang.li@windriver.com> Signed-off-by: Yang Shi <yang.shi@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-24powerpc/83xx: Remove second USB node from SBC834x DTSLiang Li
Since only one of the SoC USB devices is brought out to a physical connector on the board, remove the 2nd (USB-DR) node from the DTS. Having it present and USB enabled will cause a hang at boot. Signed-off-by: Liang Li <liang.li@windriver.com> Signed-off-by: Yang Shi <yang.shi@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-24powerpc/85xx: Add support for P2020RDB boardPoonam Aggrwal
Add support for the P2020RDB reference board from Freescale. Overview of P2020RDB platform - DDR DDR2 1G - NOR Flash 16MByte - NAND Flash 32MByte - 3 Ethernet interfaces 1) etSEC1 - RGMII - connected to a 5 port Vitesse Switch(VSC7385) - Switch is memory mapped through eLBC interface(CS#2) - IRQ1 2) etSEC2 - SGMII - connected to VSC8221 - IRQ2 3) etSEC3 - RGMII - connected to VSC8641 - IRQ3 - 2 1X PCIe interfaces - SD/MMC ,USB - SPI EEPROM - Serial I2C EEPROM Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-20powerpc: use consistent types in mktreeStephen Rothwell
gcc v4.4 currently produces this build warning: arch/powerpc/boot/mktree.c: In function 'main': arch/powerpc/boot/mktree.c:104: warning: dereferencing type-punned pointer will break strict-aliasing rules tmpbuf is only used as an array of unsigned ints, so declare it that way. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/86xx: Update GE Fanuc sbc310 DTSMartyn Welch
Update GE Fanuc DTS to match the alterations suggested during the merge of the ppc9a DTS in commit 740d36ae6344f38c4da64c2ede765d7d2dd1f132 Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/86xx: Enable XMC site on GE Fanuc SBC310Martyn Welch
This patch enables the XMC (PCIe daughter card) site on the SBC310. STG enter the description for the patch above. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/83xx: Add eSDHC support for MPC837xE-RDB/WLAN boardsAnton Vorontsov
Actually, the support is already there, but it requires newer U-Boots (to fill-in clock-frequency, and setup pin multiplexing). Though, it appears that on RDB boards USBB pins aren't multiplexed between USB and eSDHC (unlike MDS boards, where USB and eSDHC share pctl and pwrfault pins). So, for RDB boards we can safely setup pinmux and manually fill-in clock-frequency, thus making eSDHC work even with older u-boots. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/85xx: Add support for I2C EEPROMs on MPC8548CDS boardsAnton Vorontsov
This patch simply adds four eeprom nodes to MPC8548CDS' device tree. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/83xx: Add support for MPC8377E-WLAN boardsAnton Vorontsov
MPC8377E-WLAN are basically RDB boards except: - RAM extended to 512 MB; - NAND flash removed, NOR flash extended to 64 MB; - Vitesse VSC7385 5-port switch removed, RTL8211B PHY added; - Power management MCU removed; - PCI slot removed, another mini-PCI slot added (IRQ routing changed); - USB3300 PHY's ID pin grounded, thus USB port is host-only. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/82xx: mgcoge - updates for 2.6.32Heiko Schocher
- add I2C support - add FCC1 and FCC2 support - fix bogus gpio numbering in plattform code Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/85xx: Added 36-bit physical device tree for mpc8536ds boardKumar Gala
Added a device tree that should be similiar to mpc8536ds.dtb except the physical addresses for all IO are above the 4G boundary. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/85xx: Move mpc8536ds.dts to address-cells/size-cells = <2>Kumar Gala
Change the top-level #address-cells and #size-cells to <2> so the mpc8536ds.dts is easier to deal with both a true 32-bit physical or 36-bit physical address space. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/40x: Update Kilauea dts to support NAND, RTC and HWMONStefan Roese
This patch adds support for the following devices to the Kilauea dts: - PPC4xx NAND controller (NDFC) - I2C RTC (Dallas DS1338) - I2C HWMON (Dallas DS1775) Additionally the partitioning of the NOR FLASH is changed. The dtb partition has been missing. Fixed in this patch. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc/44x: Add NAND support to Canyonlands dtsStefan Roese
Also some whitespace cleanup in the USB device nodes. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20powerpc: Update boot wrapper script with the new location of dtcLucian Adrian Grijincu
dtc was moved in 9fffb55f66127b52c937ede5196ebfa0c0d50bce from arch/powerpc/boot/ to scripts/dtc/ This patch updates the wrapper script to point to the new location of dtc. Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-07-29powerpc/83xx: Fix PCI IO base address on MPC837xE-RDB boardsAnton Vorontsov
U-Boot maps PCI IO at 0xe0300000, while current dts files specify 0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y. 8139too Fast Ethernet driver 0.9.28 Machine check in kernel mode. Caused by (from SRR1=41000): Transfer error ack signal Oops: Machine check, sig: 7 [#1] MPC837x RDB [...] NIP [00000900] 0x900 LR [c0439df8] rtl8139_init_board+0x238/0x524 Call Trace: [cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable) [cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c [cf831e40] [c0235250] pci_call_probe+0x20/0x30 [...] This patch fixes the issue by specifying the correct PCI IO base address. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-29powerpc/85xx: Don't scan for TBI PHY addresses on MPC8569E-MDS boardsAnton Vorontsov
Sometimes (e.g. when there are no UEMs attached to a board) fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY, this is because get_phy_id() returns bogus 0x0000ffff values (0xffffffff is expected), and therefore mdio bus probing fails with the following message: fsl-pq_mdio: probe of e0082120.mdio failed with error -16 And obviously ethernet doesn't work after this. This patch solves the problem by adding tbi-phy node into mdio node, so that we won't scan for spare addresses, we'll just use a fixed one. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-06powerpc/4xx: Have Warp take advantage of GPIO LEDs default-state = keepSean MacLennan
The GPIO LEDS driver now has a default state of "keep". Update the Warp DTS and platform file to take advantage of this new state. This removes the hardcoding of the two LEDs on the Warp. Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-06-26Merge commit 'kumar/next' into mergeBenjamin Herrenschmidt
2009-06-26powerpc/amigaone: Limit ISA I/O range to 4k in the device treeGerhard Pircher
The kernel reserves the I/O address space from 0x0 to 0xfff for legacy ISA devices. Change the ranges property for the PCI2ISA bridge to match the kernels behavior, even if the ranges property isn't used for now. Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-06-26powerpc: Have git ignore generated files from dtc compileJon Smirl
Have git ignore generated files from dtc compile Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-06-23powerpc/85xx: Make eSDHC 1-bit only transfer mode default for MPC8569E-MDSAnton Vorontsov
For yet unknown reason 4-bit mode doesn't work on MPC8569E-MDS boards, so make 1-bit mode default. When we resolve the issue, u-boot will remove sdhci,1-bit-only property from the device tree, while SDHCI will still work with older u-boots. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-19Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (35 commits) powerpc/5121: make clock debug output more readable powerpc/5xxx: Add common mpc5xxx_get_bus_frequency() function powerpc/5200: Update pcm030.dts to add i2c eeprom and delete cruft powerpc/5200: convert mpc52xx_psc_spi to use cs_control callback fbdev/xilinxfb: Fix improper casting and tighen up probe path usb/ps3: Add missing annotations powerpc: Add memory clobber to mtspr() powerpc: Fix invalid construct in our CPU selection Kconfig ps3rom: Use ps3_system_bus_[gs]et_drvdata() instead of direct access powerpc: Add configurable -Werror for arch/powerpc of_serial: Add UPF_FIXED_TYPE flag drivers/hvc: Add missing __devexit_p() net/ps3: gelic - Add missing annotations powerpc: Introduce macro spin_event_timeout() powerpc/warp: Fix ISA_DMA_THRESHOLD default powerpc/bootwrapper: Custom build options for XPedite52xx targets powerpc/85xx: Add defconfig for X-ES MPC85xx boards powerpc/85xx: Add dts files for X-ES MPC85xx boards powerpc/85xx: Add platform support for X-ES MPC85xx boards 83xx: add support for the kmeter1 board. ...
2009-06-19powerpc/86xx: add MMC SPI support for MPC8610HPCD boardsAnton Vorontsov
This patch adds spi and mmc-spi-slot nodes, plus a gpio-controller for PIXIS' sdcsr bank that is used for managing SPI chip-select and for reading card's states. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-17powerpc/5200: Update pcm030.dts to add i2c eeprom and delete cruftWolfram Sang
Add a node for the i2c eeprom and delete the superflous gpio-example. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-06-15powerpc/bootwrapper: Custom build options for XPedite52xx targetsNate Case
Some XPedite52xx boards have a legacy boot loader requiring some special care in the boot wrapper. The use of cuboot-85xx is needed to fix up embedded device trees, and a custom link address is specified to accommodate the boot loader and larger kernel image sizes used on X-ES MPC85xx platforms. Signed-off-by: Nate Case <ncase@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>