| Age | Commit message (Collapse) | Author |
|---|
|
Enabling power fault detected event notification in current pciehp
might cause power fault interrupt storm on some machines. On those
machines. On those machines, power fault detected bit in the slot
status register was set again immediately when it is cleared in the
interrupt service routine, and next power fault detected interrupt was
notified again. Therefore, disable power fault detected event
notification for now.
This patch also removes unnecessary handling for power fault cleared
event because this event is not supported by PCIe spec.
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in pciehp driver. This avoids unnecessary search in PCI
configuration space. This patch also removes 'cap_base' field in
struct controller, that was used to hold PCIe capability offset by
pciehp itself.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp returns successfully on read/write failure with dummy
state values. It should return error instead.
With this patch, pciehp no longer uses hotplug_slot_info data
structure. So this also removes hotplug_slot_info related code. But
note that it still allocates hotplug_slot_info because it is required
by pci hotplug core.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Remove wrong workaround for BAD DLLP error, which confused surprise
down error with DLL errors.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp doesn't handle Data Link Layer State Changed Event
notification. So it needs to be disabled at initialization time,
otherwise other event notifications are not generated.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since slot_cap field in struct controller contains physical slot
number informationq, we don't need number field in struct slot.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The struct hpc_ops seems a set of hooks to controller specific
routines. But, it is meaningless because no hotplug controller driver
follows this framework.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since we have a pointer to pcie_device in struct controller, we don't
need a pointer to pci_dev.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The crit_sect mutex defined in struct controller is to serialize
hot-plug operations against multiple slots under the same bus. But,
since PCIe doesnstream port has only one slot at most, it is
meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The slot number can be calculated only by physical slot number field
in the slot capabilities register. So the first_slot field in struct
controller is meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since the device number of the hot-slot under the PCIe downstream port
is always 0, the slot_device_offset field in the slot is meaningless
and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The hp_slot field is to identify the slot under the same
controller. But, since PCIe downstream port has only one slot at most,
it is meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The device field in the struct slot is not necessary because it is
always 0 in pciehp driver.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The bus field in struct slot is not necessary.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since PCIe downstream port has only one slot at most, we don't need
num_slots field in struct controller. Note that struct controller
itself doesn't exist if PCIe downstream port has no slot.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since PCIe downstream port has only one slot at most, we don't need
'slot_list' linked list to manage multiple slots under the port.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Add support for PCI-E 5.0 GT/s in max_bus_speed and cur_bus_speed.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The EMI support in pciehp is obviously broken. It is implemented using
struct hotplug_slot_attribute, but sysfs_ops for pci_slot_ktype is NOT
for struct hotplug_slot_attribute, but for struct pci_slot_attribute.
This bug had been there for a long time, maybe it was introduced when
PCI slot framework was introduced. The reason why this bug didn't
cause any problem is maybe the EMI support is not tested at all
because of lack of test environment.
As described above, the EMI support in pciehp seems not to be tested
at all. So this patch removes EMI support from pciehp, instead of
fixing the bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp disables software notification of adapter presence
changed event and MRL changed event when slot is turned off. Because
of this, there is no way to detect those events on empty slots in the
current pciehp implementation.
According to the past discussion(*), this behavior was introduced to
prevent endless loop that could happen if pcie_isr() runs after power
fault is detected on a certain platform whose stickey power-fault bit
remains on till the slot is powered on again.
(*) http://sourceforge.net/mailarchive/message.php?msg_id=20051130135409.A14918%40unix-os.sc.intel.com
I think this endless loop can be avoided using one bit flag that
indicates power fault had been detected, instead of disabling software
notification of adapter present changed event and MRL changed event.
With this patch, we can enable software notification mechanism of
presence changed and MRL changed event on the empty slots again.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix possible endless loop in pcie_isr.
Currently, pcie_isr() (interrupt service routine of pciehp) can end up in an
endless loop if the Slot Status register is set again immediately after being
cleared. According to the past discussion (see below URL) this case can happen
if the power fault detected bit is set during handling.
http://sourceforge.net/mailarchive/message.php?msg_id=20051130135409.A14918%40unix-os.sc.intel.com
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Move the enabling of interrupts after all of the data structures
are setup so that we can safely run the interrupt handler as
soon as it is registered.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
|
|
Clean up register definitions related to PCI Express Hot plug.
- Add register definitions into include/linux/pci_regs.h, and use
them instead of pciehp's locally definied register definitions.
- Remove pciehp's locally defined register definitions
- Remove unused register definitions in pciehp.
- Some minor cleanups.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Bit 10 in Link Status register used to be defined as Training Error in
the PCI Express 1.0a specification. But it was removed by Training Error
ECN and is no longer defined. So pciehp must ignore the value read from
it.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch refines messages in pciehp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch adds polling mechanism for Data Link Layer Link Active bit
after turning power on, instead of waiting for 1000 msec. This reduces
reduce the unnecessary long wait.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the error paths in pcie_init to avoid leaking memory.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We do not need to manage our own name parameter, especially since
the PCI core can change it on our behalf, in the case of duplicate
slot names.
Remove 'name' from pciehp's version of struct slot, and remove
unused 'task_list' as well.
Cc: kristen.c.accardi@intel.com
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch replaces printks within pciehp module with dev_printks.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp driver gets irq number from pci_dev->irq. But because
pciehp driver is a pci express port service driver, it should get irq
number from pcie_device->irq.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch fixes an obvious bug (loop was never entered) caused by
commit 820943b6fc4781621dee52ba026106758a727dd3
(pciehp: cleanup pcie_poll_cmd).
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Commit 3800345f723fd130d50434d4717b99d4a9f383c8 (pciehp: fix slot name)
introduces the pciehp_slot_with_bus module parameter, which was intended
to help work around broken firmware that assigns the same name to multiple
slots.
Commit 9e4f2e8d4ddb04ad16a3828cd9a369a5a5287009 (pciehp: add message about
pciehp_slot_with_bus option) tells the user to use the above parameter
in the event of a name collision.
This approach is sub-optimal because it requires too much work from
the user.
Instead, let's rename the slot on behalf of the user. If firmware
assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
The Mth registered slot becomes N-M
In the event we overflow the slot->name parameter, we report an
error to the user.
This is a temporary fix until the entire PCI core can be reworked
such that individual drivers no longer have to manage their own
slot names.
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Comamnd->Command
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Currently, pciehp driver enables command completed interrupt as follows.
(1) Don't enable at initialization.
(2) Enable command completed interrupt whenever pciehp issues a
command, if the command doesn't attempt to disable the interrupt.
(3) Disable command completed interrupt at driver unloading.
Once we enable command completed interrupt, we don't need to re-enable
it for every command. So we can simplify above steps as follows:
(1) Enable command completed interrupt at initialization.
(2) No special sequence for command completed interrupt.
(3) Disable command completed interrupt at driver unloading.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp driver's intialization sequence is as follows:
(1) initialize controller data structure
(2) install interrupt handler
(3) enable software notification
(4) initialize controller specific slot data structure
(5) initialize generic slot data structure and register it to pci hotplug core
The interrupt handler of pciehp assumes that controller specific slot
data structure is already initialized. However, it is installed at (2)
before initializing controller specific slot data structure at
(4). Because of this, pciehp driver cannot handle the following cases
properly.
- If devices that shares IRQ with pciehp raise interrupts between (2) and (4).
- If hotplug events (e.g. MRL open) happen between (3) and (4).
We already have a workaround for this problem ("pciehp: fix NULL
dereference in interrupt handler: dbd79aed1aea2bece0bf43cc2ff3b2f9baf48a08).
But we still need fundamental fix.
This patch fix the problem by changing the initilization sequence as follows:
(1) initialize controller data structure
(2) initialize controller specific slot data structure
(3) install interrupt handler
(4) enable software notification
(5) initialize generic slot data structure and register it to pci hotplug core
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The pcie_poll_cmd() and pcie_wait_cmd() are too large to be
inlined.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Change command polling frequency to 100Hz from 10Hz in order to reduce
the delay in the common case of a command completing quickly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanup pcie_poll_cmd(): check the slot status once before entering our
completion test loop and convert the loop to a simpler while() block.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the typo in hpc_release_ctlr().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanup to remove a redundant NULL write to SLOTSTATUS.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fixup a typo in dbg_ctrl(); it was fetching SLOTSTATUS twice.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the following problems of shpchp driver about getting hotplug
control from firmware.
- The shpchp driver must not control the hotplug controller if it
fails to get control from the firmware. But current shpchp
controls the hotplug controller regardless the result, because it
doesn't check the return value of get_hp_hw_control_from_firmware().
- Current shpchp driver doesn't support _OSC.
The pciehp driver already have the code for evaluating _OSC and OSHP
and shpchp and pciehp can share it. So this patch move that code from
pciehp to acpi_pcihp.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since we need to wait for command completion for muximum 1sec, waiting
command should not be interrupted by a signal.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp evaluates _OSC/OSHP method after some controller
initialization is done. So if evaluating _OSC/OSHP is failed, we need
to cleanup already initialized data structures or hardware. This
clearly is not robust way. With this patch, _OSC/OSHP evaluation is
done first.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix improper long wait for command completion in pciehp probing.
As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.
This patch changes the pciehp driver to take such command into
account.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).
The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.
This problem seems to be revealed by the commit
c27fb883dffe11aa4cb35ecea1fa1832ba45d4da that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix the following NULL dereference problem reported from Pierre Ossman
and Ingo Molnar.
pciehp: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0
pciehp: pciehp_find_slot: slot (device=0x0) not found
BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
IP: [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
PGD 0
Oops: 0000 [1]
CPU 0
Modules linked in:
Pid: 1, comm: swapper Tainted: G W 2.6.26-rc3-sched-devel.git-00001-g2b99b26-dirty #170
RIP: 0010:[<ffffffff80494a8b>] [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
RSP: 0000:ffff81003f83fbb0 EFLAGS: 00010046
RAX: 0000000000000039 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000046
RBP: ffff81003f83fbd0 R08: 0000000000000001 R09: ffffffff80245103
R10: 0000000000000020 R11: 0000000000000000 R12: ffff81003ea53a30
R13: 0000000000000000 R14: 0000000000000011 R15: ffffffff80495926
FS: 0000000000000000(0000) GS:ffffffff80be7400(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000070 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff81003f83e000, task ffff81003f840000)
Stack: 0000000000000008 ffff81003f83fbf6 ffff81003ea53a30 0000000000000008
ffff81003f83fc10 ffffffff80495ab4 0000000000000011 0000000000000002
0000000000000202 0000000000000202 00000000fffffff4 ffff81003ea53a30
Call Trace:
[<ffffffff80495ab4>] pcie_isr+0x18e/0x1bc
[<ffffffff80260831>] request_irq+0x106/0x12f
[<ffffffff80495fb6>] pcie_init+0x15e/0x6cc
[<ffffffff804933a3>] pciehp_probe+0x64/0x541
[<ffffffff8048f4e7>] pcie_port_probe_service+0x4c/0x76
[<ffffffff8054af70>] driver_probe_device+0xd4/0x1f0
[<ffffffff8054b108>] __driver_attach+0x7c/0x7e
[<ffffffff8054b08c>] ? __driver_attach+0x0/0x7e
[<ffffffff8054a4b6>] bus_for_each_dev+0x53/0x7d
[<ffffffff8054ad3c>] driver_attach+0x1c/0x1e
[<ffffffff8054a9c2>] bus_add_driver+0xdd/0x25b
[<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
[<ffffffff8054b288>] driver_register+0x5f/0x13e
[<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
[<ffffffff8048f441>] pcie_port_service_register+0x47/0x49
[<ffffffff80c09d52>] pcied_init+0x15/0x8b
[<ffffffff80bf3938>] kernel_init+0x75/0x243
[<ffffffff808639d2>] ? _spin_unlock_irq+0x2b/0x3a
[<ffffffff80228d1f>] ? finish_task_switch+0x57/0x9a
[<ffffffff8020c258>] child_rip+0xa/0x12
[<ffffffff8020bcec>] ? restore_args+0x0/0x30
[<ffffffff80bf38c3>] ? kernel_init+0x0/0x243
[<ffffffff8020c24e>] ? child_rip+0x0/0x12
Code: 83 80 00 00 00 48 39 f0 75 e1 0f b6 c9 48 c7 c2 00 0e 8d 80 48 c7 c6 8a 60 a6 80 48 c7 c7 10 db a8 80 31 c0 e8 3f 8d d9 ff 31 db <48> 8b 43 70 48 8d 75 ef 48 89 df ff 50 30 80 7d ef 00 74 37 48
RIP [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
RSP <ffff81003f83fbb0>
CR2: 0000000000000070
Kernel panic - not syncing: Fatal exception
The situation under which it occurs is hw and timing related: it appears
to happen on a system that has PCI hotplug hardware but with no active
hotplug cards, and another interrupt in the same (shared) IRQ line
arrives too early, before the hotplug-slot entry has been set up - as
triggered by CONFIG_DEBUG_SHIRQ=y:
This patch contains the following two fixes.
(1) Clear all events bits in Slot Status register to prevent the pciehp
driver from detecting the spurious events that would have been occur
before pciehp loading.
(2) Add check whether slot initialization had been already done.
This is short term fix. We need more structural fixes to install
interrupt handler after slot initialization is done.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
People are confused by the following error message that actually is
not for indicating a error.
Cannot get control of hotplug hardware for pci %s
This patch changes this message to debug message.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
|
|
Current implementation of pciehp_write_cmd() always enables command
completed interrupt. But pciehp_write_cmd() is also used for clearing
command completed interrupt enable bit. In this case, we must not set
the command completed interrupt enable bit. To fix this bug, this
patch add the check to see if caller wants to change command complete
interrupt enable bit.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
this_patch_makes_the_needlessly_global_pciehp_acpi_get_hp_hw_control_from_firmware_static
;)
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
