| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
* 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: add hardware handshake support to atmel_serial
avr32: add RTS/CTS/CLK pin selection for the USARTs
Add RTC support for Merisc boards
avr32: at32ap700x: setup DMA for AC97C in the machine code
avr32: at32ap700x: setup DMA for ABDAC in the machine code
Add Merisc board support
avr32: use gpio_is_valid() to check USBA vbus_pin I/O line
atmel-usba-udc: use gpio_is_valid() to check vbus_pin I/O line
avr32: fix timing LCD parameters for EVKLCD10X boards
avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
avr32: configure MCI detect and write protect pins for EVKLCD10x boards
avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
avr32: add pin mask for 18-bit color on the LCD controller
avr32: fix 15-bit LCDC pin mask to use MSB lines
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (41 commits)
m68knommu: improve compile arch switch settings
m68knommu: fix 5407 ColdFire UART vector setup
m68knommu: fix 5307 ColdFire UART vector setup
m68knommu: fix 5249 ColdFire UART vector setup
m68knommu: fix 5249 ColdFire UART setup
m68knommu: fix end of uart table marker
m68knommu: switch to using generic_handle_irq()
m68k: merge the mmu and non-mmu versions of tlbflush.h
m68knommu: introduce basic clk infrastructure
m68k: merge the mmu and non-mmu versions of module.h
m68knommu: add missing interrupt line definition for UART 2
m68k: merge the mmu and non-mmu versions of mmu_context.h
m68k: merge the mmu and non-mmu versions of current.h
m68k: merge the mmu and non-mmu versions of div64.h
m68k: merge the mmu and non-mmu versions of bugs.h
m68k: merge the mmu and non-mmu versions of bug.h
m68k: use the mmu version of cache.h for m68knommu as well
m68k: use the mmu version of bootinfo.h for m68knommu as well
m68k: merge the mmu and non-mmu versions of fb.h
m68k: merge the mmu and non-mmu versions of segment.h
...
|
|
"struct tty_driver *" lies in m->private not in v which is
SEQ_TOKEN_START which is 1 which is enough to trigger NULL dereference
next line:
BUG: unable to handle kernel NULL pointer dereference at 000000ad
IP: [<c040d689>] uart_proc_show+0xe/0x2b0
Noticed by Linus.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adds Hardware Handshake (aka RTS/CTS flow-control) support to
atmel_serial driver, as a termios flag.
For this to actually work, the platform code needs to configure the RTS
and CTS pins for use by the USART. This has been done for AVR32 as a
separate patch.
Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
|
|
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Manual merge of:
arch/powerpc/include/asm/elf.h
drivers/i2c/busses/i2c-mpc.c
|
|
Conflicts:
sound/soc/pxa/pxa2xx-i2s.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (61 commits)
Dynamic debug: fix pr_fmt() build error
Dynamic debug: allow simple quoting of words
dynamic debug: update docs
dynamic debug: combine dprintk and dynamic printk
sysfs: fix some bin_vm_ops errors
kobject: don't block for each kobject_uevent
sysfs: only allow one scheduled removal callback per kobj
Driver core: Fix device_move() vs. dpm list ordering, v2
Driver core: some cleanup on drivers/base/sys.c
Driver core: implement uevent suppress in kobject
vcs: hook sysfs devices into object lifetime instead of "binding"
driver core: fix passing platform_data
driver core: move platform_data into platform_device
sysfs: don't block indefinitely for unmapped files.
driver core: move knode_bus into private structure
driver core: move knode_driver into private structure
driver core: move klist_children into private structure
driver core: create a private portion of struct device
driver core: remove polling for driver_probe_done(v5)
sysfs: reference sysfs_dirent from sysfs inodes
...
Fixed conflicts in drivers/sh/maple/maple.c manually
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Cc: davem@davemloft.net
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel
|
|
Due to a case of backwards logic, mfc.c always makes the console port be
ttyS0 even when you ask for another port.
This patch fixes this issue.
Only when the requested port is NOT in the range 0 to MAXPORTS-1 do we
force it to be treated as if port 0 was requested. Forcing the port to
0 when it is in fact in the range 0 to MAXPORTS is not helpful.
Tested with working console on ttyS2 on a 5271evb.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
Conflicts:
arch/arm/mach-at91/gpio.c
|
|
The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
After UART interrupt handler is installed and rx is enabled, if an rx
interrupt comes before hardware init, rx->cur will be updated. Then the
hardware init will reset BD and make rx->cur out of sync, move the hardware
init code before request_irq.
Signed-off-by: Xiaotian Feng <xiaotian.feng@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The only things prevent drivers/serial/pxa.c from being generic enough
are:
1. IER_UUE which can be safely replaced by UART_IER_UUE as defined in
serial_reg.h for PXA
2. __PREG() and FFUART/BTUART/STUART definitions to decide the UART
port name
And removed the un-necessary #include of <mach/...> and <asm/...> headers.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
This adds preliminary support for the SH7786 CPU subtype.
While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.
More information on this particular CPU subtype is available at:
http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: ap325rxa: Revert ov772x support.
serial: sh-sci: fix overrun error handling for SH7785 SCIF.
sh: Storage class should be before const qualifier
|
|
Modify the serial console code to wait for the transmit FIFO,
make sure all bits have been put on the wire before returning.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Intel 8257x Ethernet boards have a feature called Serial Over Lan.
This feature works by emulating a serial port, and it is detected by
kernel as a normal 8250 port. However, this emulation is not perfect, as
also noticed on changeset 7500b1f602aad75901774a67a687ee985d85893f.
Before this patch, the kernel were trying to check if the serial TX is
capable of work using IRQ's.
This were done with a code similar this:
serial_outp(up, UART_IER, UART_IER_THRI);
lsr = serial_in(up, UART_LSR);
iir = serial_in(up, UART_IIR);
serial_outp(up, UART_IER, 0);
if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
up->bugs |= UART_BUG_TXEN;
This works fine for other 8250 ports, but, on 8250-emulated SoL port, the
chip is a little lazy to down UART_IIR_NO_INT at UART_IIR register.
Due to that, UART_BUG_TXEN is sometimes enabled. However, as TX IRQ keeps
working, and the TX polling is now enabled, the driver miss-interprets the
IRQ received later, hanging up the machine until a key is pressed at the
serial console.
This is the 6 version of this patch. Previous versions were trying to
introduce a large enough delay between serial_outp and serial_in(up,
UART_IIR), but not taking forever. However, the needed delay couldn't be
safely determined.
At the experimental tests, a delay of 1us solves most of the cases, but
still hangs sometimes. Increasing the delay to 5us was better, but still
doesn't solve. A very high delay of 50 ms seemed to work every time.
However, poking around with delays and pray for it to be enough doesn't
seem to be a good approach, even for a quirk.
So, instead of playing with random large arbitrary delays, let's just
disable UART_BUG_TXEN for all SoL ports.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I have a Digi Neo 8 PCI card (114f:00b1) Serial controller: Digi
International Digi Neo 8 (rev 05)
that works with the jsm driver after using the following patch.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: Scott H Kilau <Scott_Kilau@digi.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I found a problem of handling of modem status of atmel_serial driver.
With the commit 1ecc26 ("atmel_serial: split the interrupt handler"),
handling of modem status signal was splitted into two parts. The
atmel_tasklet_func() compares new status with irq_status_prev, but
irq_status_prev is not correct if signal status was changed while the port
is closed.
Here is a sequence to cause problem:
1. Remote side sets CTS (and DSR).
2. Local side close the port.
3. Local side clears RTS and DTR.
4. Remote side clears CTS and DSR.
5. Local side reopen the port. hw_stopped becomes 1.
6. Local side sets RTS and DTR.
7. Remote side sets CTS and DSR.
Then CTS change interrupt can be received, but since CTS bit in
irq_status_prev and new status is same, uart_handle_cts_change() will not
be called (so hw_stopped will not be cleared, i.e. cannot send any data).
I suppose irq_status_prev should be initialized at somewhere in open
sequence.
Itai Levi pointed out that we need to initialize atmel_port->irq_status
as well here. His analysis is as follows:
> Regarding the second part of the patch (which resets irq_status_prev),
> it turns out that both versions of the patch (mine and Atsushi's)
> still leave enough room for faulty behavior when opening the port.
>
> This is because we are not resetting both irq_status_prev and
> irq_status in atmel_startup() to CSR, which leads faulty behavior in
> the following sequences:
>
> First case:
> 1. closing the port while CTS line = 1 (TX not allowed)
> 2. setting CTS line = 0 (TX allowed)
> 3. opening the port
> 4. transmitting one char
> 5. Cannot transmit more chars, although CTS line is 0
>
> Second case:
> 1. closing the port while CTS line = 0 (TX allowed)
> 2. setting CTS line = 1 (TX not allowed)
> 3. opening the port
> 4. receiving some chars
> 5. Now we can transmit, although CTS line is 1
>
> This reason for this is that the tasklet is scheduled as a result of
> TX or RX interrupts (not a status change!), in steps 4 above. Inside
> the tasklet, the atmel_port->irq_status (which holds the value from
> the previous session) is compared to atmel_port->irq_status_prev.
> Hence, a status-change of the CTS line is faultily detected.
>
> Both cases were verified on 9260 hardware.
[haavard.skinnemoen@atmel.com: folded with patch from Itai Levi]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: Itai Levi <itai.levi.devel@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
There was a typo for the overrun bit definition, causing it not to be
handled correctly on SH7785, fix it up.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The MPC5200 PSC device is wired up to a dedicated interrupt line
which is never shared. This patch removes the IRQF_SHARED flag
from the request_irq() call which eliminates the "IRQF_DISABLED
is not guaranteed on shared IRQs" warning message from the console
output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
There is no reason for the PSC UART driver or the Ethernet driver
to require a device_type property. The compatible value is sufficient
to uniquely identify the device. Remove it from the driver.
The whole 'port-number' scheme for assigning numbers to PSC uarts was
always rather half baked and just adds complexity. Remove it from the
driver. After this patch is applied, PSC UART numbers are simply
assigned from the order they are found in the device tree (just like
all the other devices). Userspace can query sysfs to determine what
ttyPSC number is assigned to each PSC instance.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
This fixes a crash observed when non-existant enable_ms function is
called for jsm driver.
Signed-off-by: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
|
|
This Patch add the device information for the
MIC-3620 8-port RS-232 cPCI card from Advantech Co. Ltd.
Signed-off-by: Michael Bramer <grisu@deb-support.de>
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The function jsm_remove_one is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Enabled serial UART driver for PNX833X devices.
Signed-off-by: Ihar Hrachyshka <ihar.hrachyshka@gmail.com>
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I noticed (the hard way) that the mcf.c driver doesn't support the fractional precision register on the MCF5272. This makes the console dicey at 115200 baud and a system clock of 66.0 MHz. On the other hand, if your hardware is running at 66.666 MHz, it probably isn't a problem.
Patch submitted by John Adamson <jadamson@allen-organ.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds the SCSPTR register to the sh-sci driver in
the case of sh7723 to make sure early printk builds properly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Missing definitions for PORT_xxx defs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds support for "ns16850" as supported value
of the compatible node in flat device tree uart descriptions.
This is needed for example when you have a XR16C2850 uart
connected to a PPC405's external bus controller.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fix the following problem, related to hardware flow control (CTS/RTS):
Transmitting while CTS line is asserted in DMA mode, due to not checking
for tx-stopped condition.
We found these problems while testing the UARTs with hardware
flow-control.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: "Andrew Victor" <avictor.za@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was not implemented correctly for the pnx8xxx_uart driver.
[From further discussion:
Correct, you can look to it as two separate bugs:
a) the next character is not ignored while it should;
b) the status bits 31-8 are copied to the 'ch' variable while they shouldn't.
Both bugs prevent correct break signal handling (and therefore correct
behaviour of the magic SysRq key). Bug b didn't cause too much trouble
earlier because in most situations the status bits are all zero; for
this case they unfortunately aren't.
]
Signed-off-by: Mischa Jonker <mischa.jonker@nxp.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add SupraExpress 336i PnP Voice Modem
Tested and working with the following device: (output from lspnp -v)
01:01.00 SUP1381 (unknown)
state = active
io 0x2f8-0x2ff
irq 3
Signed-off-by: Daniel Gagnon <daniel.gagnon@yahoo.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Most of netmos 9835 hardware is handled by parport-serial. IBM introduces
a device which doesn't have any parallel ports and have screwed subdevice
PCI id (not corresponding to port numbers).
Handle this device (9710:9835 1014:0299) properly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit b430428a188e8a434325e251d0704af4b88b4711 ("8250: Don't clobber
spinlocks.") introduced a regression on the parisc architecture, which
broke the handover to the serial port at boottime.
early_serial_setup() was changed to only copy a subset of the uart_port
fields, and sadly the "type" and "line" fields were forgotten and thus
the serial port was not initialized and could not be used for a
handover. This patch fixes this by copying the missing fields.
As this change to early_serial_setup() doesn't need an initialized
spinlock in the uart_port struct any longer, we can drop the spinlock
initialization in the superio driver.
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Julia Lawall found an un-needed check in the neo driver. Her patch moves
the check to cover the code dereferencing it, however it cannot be NULL
anyway so remove the NULL check instead.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
[ARM] fix pxa930_trkball build errors
[ARM] fix netx
[ARM] fix pnx4008
[ARM] fix pxa
[ARM] remove missed CLPS7500 defconfig
[ARM] clps711x: fix warning in edb7211-mm.c
[ARM] clps711x: fix warning in fortunet
[ARM] fix AT91, davinci, h720x, ks8695, msm, mx2, mx3, netx, omap1, omap2, pxa, s3c
[ARM] Fix realview build
[ARM] 5357/1: Kirkwood: add missing ge01 tclk initialization
[ARM] 5358/1: AT2440EVB: Use new include path of mci.h
[ARM] 5361/1: mv78xx0: fix compilation error
[ARM] 5360/1: Orion: fix compilation error
[ARM] 5359/1: Kirkwood: fix compilation error
[ARM] S3C64XX: Fix EINT group macro definition
[ARM] Ensure CONFIG_SERIAL_SAMSUNG_UARTS is always set.
[ARM] S3C24XX: Add gpio_to_irq implementation
[ARM] S3C24XX: Add gpio_to_irq() facility
[ARM] footbridge: dc21285.c warning fixes
[ARM] footbridge: add isa_init_irq() to common header
...
|
|
Always set CONFIG_SERIAL_SAMSUNG_UARTS when building any
of the S3C platforms as even if the driver is not selected
there it is still the facility for the machine files to
register configuration data for the possibility of the
driver being built.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
