| Age | Commit message (Collapse) | Author |
|---|
|
|
|
* Allow multiple boards to be selected in a single build
* Removed Kconfig option '85xx' which existed only for compat with arch/ppc
* Added a multiplatform 85xx defconfig (mpc85xx_defconfig). This builds
all 85xx boards except sbc8560 and stx_gp3 since these to boards have
board specific ifdef in driver code that may break all other boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The mpc8315 shares the same SATA controller as the mpc837x,
and likelihood is that future SoCs from Freescale will also.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
In case of QE we can use brg-frequency (which is qeclk/2).
Thus no need to divide sysclk in the spi_mpc83xx.
This patch also adds code to use get_brgfreq() on QE chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
device_type property is bogus, thus use proper compatible.
Also change compatible property to "fsl,ucc-mdio".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Rename commproc.[ch] to cpm1.[ch] to be more consistent with cpm2. Also
rename cpm2_common.c to cpm2.c as suggested by Scott Wood. Adjust the
includes accordingly.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The common arch/powerpc code calls in to functions in setup-bus.c
so some builds of ppc32 would fail.
Note, ppc32 usage of setup-irq.c is limited to arch/ppc and should be
removed when arch/ppc goes away.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It is dangerous for an mpc52xx device driver to modify the port_config
register. If the driver is probed incorrectly, it will change the pin
IO configuration in ways which may not be compatible with the board.
port_config should be set up by the bootloader, or failing that, in
the platform setup code in arch/powerpc/platforms/52xx.
Also, modifying CDM registers directly can cause a race condition with
other drivers. Instead call a common routine to modify CDM settings.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Dragos Carp <dragos.carp@toptica.com>
|
|
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
A general housekeeping change of the PS3 vuart variable
vuart_bus_priv.probe_mutex from semaphore to mutex.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add PS3 logical performance monitor (lpm) device driver.
The PS3's LV1 hypervisor provides a Logical Performance Monitor that
abstracts the Cell processor's performance monitor features for use
by guest operating systems.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Cleanup coding errors in drivers/ps3/ps3-vuart.c as reported by
checkpatch.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Cleanup coding errors in drivers/ps3/ps3-sys-manager.c as reported
by checkpatch.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Change the PS3 bus_id and dev_id from type unsigned int to u64. These
IDs are 64-bit in the repository, and the special storage notification
device has a device ID of ULONG_MAX.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into for-2.6.25
|
|
This patch adds support to use the fixed-link property of an ethernet node
to fs_enet for the CONFIG_PPC_CPM_NEW_BINDING case.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Vitali Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
cpmux is need in all cases, having wrapped by the ifndef CONFIG_STX_GP3
was causing a compile error.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
drivers/rapidio/rio.c: In function 'rio_get_asm':
drivers/rapidio/rio.c:413: error: implicit declaration of function 'in_interrupt'
drivers/rapidio/rio.c: In function 'rio_init_mports':
drivers/rapidio/rio.c:480: warning: format '%8.8lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
drivers/rapidio/rio.c:480: warning: format '%8.8lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add file ucc_uart.c, a serial device driver for the Freescale QUICCEngine.
Update the Kconfig and Makefile accordingly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
With that patch fixed.c now fully emulates MDIO bus, thus no need
to duplicate PHY layer functionality. That, in turn, drastically
simplifies the code, and drops down line count.
As an additional bonus, now there is no need to register MDIO bus
for each PHY, all emulated PHYs placed on the platform fixed MDIO bus.
There is also no more need to pre-allocate PHYs via .config option,
this is all now handled dynamically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.
README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (it87) request only Environment Controller ports
|
|
The extra rom[0] check is flagging valid temperatures as invalid when
there is already a CRC data transmission check.
w1_therm_read_bin()
if (rom[8] == crc && rom[0])
verdict = 1;
Requiring rom[0] to be non-zero will flag as invalid temperature
conversions when the low byte is zero, specifically the temperatures 0C,
16C, 32C, 48C, -16C, -32C, and -48C.
The CRC check is produced on the device for the previous 8 bytes and is
required to ensure the data integrity in transmission. I don't see why the
extra check for rom[0] being non-zero is in there. Evgeniy Polyakov didn't
know either. Just for a check I unplugged the sensor, executed a
temperature conversion, and read the results. The read was all ff's, which
also failed the CRC, so it doesn't need to protect against a disconnected
sensor.
I have more extensive patches in the work, but these two trivial ones will
do for today. I would like to hear from people who use the ds2490 USB to
one wire dongle. 1 if you would be willing to test the patches as I
currently only have the one sensor on a short parisite powered wire, 2 if
there is any cheap sources for the ds2490.
Signed-off-by: David Fries <david@fries.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Correct the decoding of negative C temperatures. The code did a binary OR
of two bytes to make a 16 bit value, but assignd it to an integer. This
caused the value to not be sign extended and to loose that it was a
negative number in the assignment.
Before the patch (in my freezer),
w1_slave
ed fe 4b 46 7f ff 03 10 e4 : crc=e4 YES
ed fe 4b 46 7f ff 03 10 e4 t=4078
With the patch,
e3 fe 4b 46 7f ff 0d 10 81 : crc=81 YES
e3 fe 4b 46 7f ff 0d 10 81 t=-17
Signed-off-by: David Fries <david@fries.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The IT8705F and related parts are Super I/O controllers that contain
many separate devices.
Some BIOSes describe IT8705F I/O port usage under a motherboard device
(PNP0C02) with overlapping regions, e.g., 0x290-0x29f and 0x290-0x294.
The it87 driver supports only the Environment Controller, which requires
only two ISA ports, but it used to request an eight-port range. If that
range exceeds a range reported by the BIOS, as 0x290-0x297 would, the
request fails, and the it87 driver cannot claim the device.
This patch makes the it87 driver request only the two ports used for the
Environment Controller device.
Systems where this problem has been reported:
Gigabyte GA-K8N Ultra 9
Gigabyte M56S-S3
Gigabyte GA-965G-DS3
Kernel bug reports:
http://bugzilla.kernel.org/show_bug.cgi?id=9514
http://lkml.org/lkml/2007/12/4/466
Related change:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=a7839e960675b549f06209d18283d5cee2ce9261
The patch above increases the number of PNP port resources we support.
Prior to this patch, we ignored some port resources, which masked the
it87 problem.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[ICMP]: ICMP_MIB_OUTMSGS increment duplicated
[IPV6]: RFC 2011 compatibility broken
[IPV6]: ICMP6_MIB_OUTMSGS increment duplicated
[NET]: rtnl_link: fix use-after-free
[AF_KEY]: Fix skb leak on pfkey_send_migrate() error
[ATM] atm/suni.c: Fix section mismatch.
[ATM] atm/idt77105.c: Fix section mismatch.
[IrDA]: af_irda memory leak fixes
[NEIGH]: Revert 'Fix race between neigh_parms_release and neightbl_fill_parms'
[NETFILTER]: bridge-netfilter: fix net_device refcnt leaks
[IPV6] ROUTE: Make sending algorithm more friendly with RFC 4861.
[IPV4] FIB_HASH : Avoid unecessary loop in fn_hash_dump_zone()
[NET]: Fix interrupt semaphore corruption in Intel drivers.
[IPV4] fib_trie: fix duplicated route issue
[IPV4] fib_hash: fix duplicated route issue
[IPV6]: Mischecked tw match in __inet6_check_established.
rfkill: call rfkill_led_trigger_unregister() on error
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
tc35815: Use irq number for tc35815-mac platform device id
[MIPS] Malta: Fix reading the PCI clock frequency on big-endian
[MIPS] SMTC: Fix build error.
|
|
Fix line length calculation. var->width is the size of the display in mm. We
like to use the pixel size.
Without this fix, dynamic (fbset) based resolution and depths changes with
s3c2410_fb don't work at all.
Spotted by john cass <johnpcass@yahoo.com>
Signed-off-by: Stefan Schmidt <stefan@openmoko.org>
Signed-off-by: Harald Welte <laforge@openmoko.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
|
|
If we get a data URB back from the hardware after we have put the tty to
bed we go kaboom. Fortunately all we need to do is process the URB without
trying to ram its contents down the throat of an ex-tty.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
|
|
The tc35815-mac platform device used a pci bus number and a devfn to
identify its target device, but the pci bus number may vary if some
bus-bridges are found. Use irq number which is be unique for embedded
controllers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In preparation of adding MPC5121 support
cleanup some things that checkpatch.pl complains
about also some minor fixes suggested by
Stephen Rothwell.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This is in preparation for the addition of MPC512x
PSC support. The main difference in the 512x is
in the fifo registers.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
When unregistering the rtnl_link_ops, all existing devices using
the ops are destroyed. With nested devices this may lead to a
use-after-free despite the use of for_each_netdev_safe() in case
the upper device is next in the device list and is destroyed
by the NETDEV_UNREGISTER notifier.
The easy fix is to restart scanning the device list after removing
a device. Alternatively we could add new devices to the front of
the list to avoid having dependant devices follow the device they
depend on. A third option would be to only restart scanning if
dev->iflink of the next device matches dev->ifindex of the current
one. For now this seems like the safest solution.
With this patch, the veth rtnl_link_ops unregistration can use
rtnl_link_unregister() directly since it now also handles destruction
of multiple devices at once.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EXPORT_SYMBOL'ed code mustn't be __*init.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EXPORT_SYMBOL'ed code mustn't be __*init.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several of the Intel ethernet drivers keep an atomic counter used to
manage when to actually hit the hardware with a disable or an enable.
The way the net_rx_work() breakout logic works during a pending
napi_disable() is that it simply unschedules the poll even if it
still has work.
This can potentially leave interrupts disabled, but that is OK
because all of the drivers are about to disable interrupts
anyways in all such code paths that do a napi_disable().
Unfortunately, this trips up the semaphore used here in the Intel
drivers. If you hit this case, when you try to bring the interface
back up it won't enable interrupts. A reload of the driver module
fixes it of course.
So what we do is make sure all the sequences now go:
napi_disable();
atomic_set(&adapter->irq_sem, 0);
*_irq_disable();
which makes sure the counter is always in the correct state.
Reported by Robert Olsson.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was moved to arch/x86/lguest/Kconfig, but I lost the deletion part in a
patch suffle. My confused one-liner "fix" to turn it on is also reverted:
84f7466ee20cc094aa38617abfa2f3834871f054
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The PDC202xx older devices do not support ATAPI DMA via the usual
interfaces. What documentation I have isn't sufficient to support DMA and
it isn't clear if the Windows drivers do this or it is possible at all.
(Neither do the drivers/ide old drivers)
So turn it ATAPI DMA off, these are disk optimised controllers.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: Fix receiving UD messages with immediate data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (31 commits)
Replace cpmac fix
dl2k: the rest
dl2k: MSCR, MSSR, ESR, PHY_SCR fixes
dl2k: BMSR fixes
dl2k: ANAR, ANLPAR fixes
dl2k: BMCR_t fixes
3c574, 3c515 bitfields abuse
sbni endian fixes
wan/lmc bitfields fixes
dscc4 endian fixes
S2io: Fixed synchronization between scheduling of napi with card reset and close
atl1: fix frame length bug
Documentation: add a guideline for hard_start_xmit method
Revert "sky2: remove check for PCI wakeup setting from BIOS"
e1000e Kconfig: remove ref to nonexistant docs
bonding: Don't hold lock when calling rtnl_unlock
bonding: fix lock ordering for rtnl and bonding_rwsem
bonding: Fix up parameter parsing
bonding: release slaves when master removed via sysfs
bonding: fix locking during alb failover and slave removal
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] clarify watchdog operation in documentation
[WATCHDOG] Revert "Stop looking for device as soon as one is found"
|
|
There's currently no way to turn on Lguest guest support; the planned
Kconfig virtualization reorg didn't get into 2.6.25.
This was unnoticed because if you already had CONFIG_LGUEST_GUEST=y in
your config, it worked. Too bad about new users...
Also, the Kconfig help was wrong now the virtio drivers are merged.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 3ff6eb4a2fe5757cbe7c5d57c8eb60ab0775f2f0.
the !found check in the for loop allready made sure that only one
device was found.
Signed-Off-By: Pádraig Brady <P@draigBrady.com>
Signed-Off-By: Wim Van Sebroeck <wim@iguana.be>
|
|
Please apply this patch since i reverted by mistake
the commit 4e3ab47a547616e583c7a5458beced6aa34c8ef3
in 6cd043d99dcf5d252fcc682958541f449113f7b3
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
remove an unused union-with-bitfield of the same sort,
add missing conversions in debugging printk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
same story, different registers...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
broken use of bitfields; FUBAR on big-endian (and not valid C,
strictly speaking).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
