From 48773e685b118ef56dcf5258ef7388a4bea16137 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sat, 25 Mar 2006 09:21:43 -0300 Subject: V4L/DVB (3599c): Whitespace cleanups under Documentation/video4linux Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CQcam.txt | 182 +++++++++++++-------------- Documentation/video4linux/README.cpia | 4 +- Documentation/video4linux/Zoran | 108 ++++++++-------- Documentation/video4linux/bttv/ICs | 4 +- Documentation/video4linux/bttv/PROBLEMS | 16 +-- Documentation/video4linux/bttv/README.quirks | 4 +- Documentation/video4linux/bttv/THANKS | 4 +- Documentation/video4linux/radiotrack.txt | 16 +-- Documentation/video4linux/w9966.txt | 2 +- Documentation/video4linux/zr36120.txt | 4 +- 10 files changed, 172 insertions(+), 172 deletions(-) diff --git a/Documentation/video4linux/CQcam.txt b/Documentation/video4linux/CQcam.txt index e415e360453..464e4cec94c 100644 --- a/Documentation/video4linux/CQcam.txt +++ b/Documentation/video4linux/CQcam.txt @@ -1,7 +1,7 @@ c-qcam - Connectix Color QuickCam video4linux kernel driver Copyright (C) 1999 Dave Forrest - released under GNU GPL. + released under GNU GPL. 1999-12-08 Dave Forrest, written with kernel version 2.2.12 in mind @@ -45,21 +45,21 @@ configuration. The appropriate flags are: CONFIG_PNP_PARPORT M for autoprobe.o IEEE1284 readback module CONFIG_PRINTER_READBACK M for parport_probe.o IEEE1284 readback module CONFIG_VIDEO_DEV M for videodev.o video4linux module - CONFIG_VIDEO_CQCAM M for c-qcam.o Color Quickcam module + CONFIG_VIDEO_CQCAM M for c-qcam.o Color Quickcam module With these flags, the kernel should compile and install the modules. To record and monitor the compilation, I use: (make zlilo ; \ make modules; \ - make modules_install ; + make modules_install ; depmod -a ) &>log & less log # then a capital 'F' to watch the progress - + But that is my personal preference. 2.2 Configuration - + The configuration requires module configuration and device configuration. I like kmod or kerneld process with the /etc/modprobe.conf file so the modules can automatically load/unload as @@ -68,7 +68,7 @@ using MAKEDEV, or need to be created. The following sections detail these procedures. -2.1 Module Configuration +2.1 Module Configuration Using modules requires a bit of work to install and pass the parameters. Understand that entries in /etc/modprobe.conf of: @@ -128,9 +128,9 @@ system (CONFIG_PROC_FS), the parallel printer support (CONFIG_PRINTER), the IEEE 1284 system,(CONFIG_PRINTER_READBACK), you should be able to read some identification from your quickcam with - modprobe -v parport - modprobe -v parport_probe - cat /proc/parport/PORTNUMBER/autoprobe + modprobe -v parport + modprobe -v parport_probe + cat /proc/parport/PORTNUMBER/autoprobe Returns: CLASS:MEDIA; MODEL:Color QuickCam 2.0; @@ -140,7 +140,7 @@ Returns: and well. A common problem is that the current driver does not reliably detect a c-qcam, even though one is attached. In this case, - modprobe -v c-qcam + modprobe -v c-qcam or insmod -v c-qcam @@ -152,16 +152,16 @@ video4linux mailing list and archive for more current information. 3.1 Checklist: Can you get an image? - v4lgrab >qcam.ppm ; wc qcam.ppm ; xv qcam.ppm + v4lgrab >qcam.ppm ; wc qcam.ppm ; xv qcam.ppm - Is a working c-qcam connected to the port? - grep ^ /proc/parport/?/autoprobe + Is a working c-qcam connected to the port? + grep ^ /proc/parport/?/autoprobe - Do the /dev/video* files exist? - ls -lad /dev/video + Do the /dev/video* files exist? + ls -lad /dev/video - Is the c-qcam module loaded? - modprobe -v c-qcam ; lsmod + Is the c-qcam module loaded? + modprobe -v c-qcam ; lsmod Does the camera work with alternate programs? cqcam, etc? @@ -174,7 +174,7 @@ video4linux mailing list and archive for more current information. isn't, you might try patching the c-qcam module to add a parport=xxx option as in the bw-qcam module so you can specify the parallel port: - insmod -v c-qcam parport=0 + insmod -v c-qcam parport=0 And bypass the detection code, see ../../drivers/char/c-qcam.c and look for the 'qc_detect' code and call. @@ -183,12 +183,12 @@ look for the 'qc_detect' code and call. this work is documented at the video4linux2 site listed below. -9.0 --- A sample program using v4lgrabber, +9.0 --- A sample program using v4lgrabber, This program is a simple image grabber that will copy a frame from the first video device, /dev/video0 to standard output in portable pixmap format (.ppm) Using this like: 'v4lgrab | convert - c-qcam.jpg' -produced this picture of me at +produced this picture of me at http://mug.sys.virginia.edu/~drf5n/extras/c-qcam.jpg -------------------- 8< ---------------- 8< ----------------------------- @@ -202,8 +202,8 @@ produced this picture of me at * Use as: * v4lgrab >image.ppm * - * Copyright (C) 1998-05-03, Phil Blundell - * Copied from http://www.tazenda.demon.co.uk/phil/vgrabber.c + * Copyright (C) 1998-05-03, Phil Blundell + * Copied from http://www.tazenda.demon.co.uk/phil/vgrabber.c * with minor modifications (Dave Forrest, drf5n@virginia.edu). * */ @@ -225,55 +225,55 @@ produced this picture of me at #define READ_VIDEO_PIXEL(buf, format, depth, r, g, b) \ { \ - switch (format) \ - { \ - case VIDEO_PALETTE_GREY: \ - switch (depth) \ - { \ - case 4: \ - case 6: \ - case 8: \ - (r) = (g) = (b) = (*buf++ << 8);\ - break; \ - \ - case 16: \ - (r) = (g) = (b) = \ - *((unsigned short *) buf); \ - buf += 2; \ - break; \ - } \ - break; \ - \ - \ - case VIDEO_PALETTE_RGB565: \ - { \ - unsigned short tmp = *(unsigned short *)buf; \ - (r) = tmp&0xF800; \ - (g) = (tmp<<5)&0xFC00; \ - (b) = (tmp<<11)&0xF800; \ - buf += 2; \ - } \ - break; \ - \ - case VIDEO_PALETTE_RGB555: \ - (r) = (buf[0]&0xF8)<<8; \ - (g) = ((buf[0] << 5 | buf[1] >> 3)&0xF8)<<8; \ - (b) = ((buf[1] << 2 ) & 0xF8)<<8; \ - buf += 2; \ - break; \ - \ - case VIDEO_PALETTE_RGB24: \ - (r) = buf[0] << 8; (g) = buf[1] << 8; \ - (b) = buf[2] << 8; \ - buf += 3; \ - break; \ - \ - default: \ - fprintf(stderr, \ - "Format %d not yet supported\n", \ - format); \ - } \ -} + switch (format) \ + { \ + case VIDEO_PALETTE_GREY: \ + switch (depth) \ + { \ + case 4: \ + case 6: \ + case 8: \ + (r) = (g) = (b) = (*buf++ << 8);\ + break; \ + \ + case 16: \ + (r) = (g) = (b) = \ + *((unsigned short *) buf); \ + buf += 2; \ + break; \ + } \ + break; \ + \ + \ + case VIDEO_PALETTE_RGB565: \ + { \ + unsigned short tmp = *(unsigned short *)buf; \ + (r) = tmp&0xF800; \ + (g) = (tmp<<5)&0xFC00; \ + (b) = (tmp<<11)&0xF800; \ + buf += 2; \ + } \ + break; \ + \ + case VIDEO_PALETTE_RGB555: \ + (r) = (buf[0]&0xF8)<<8; \ + (g) = ((buf[0] << 5 | buf[1] >> 3)&0xF8)<<8; \ + (b) = ((buf[1] << 2 ) & 0xF8)<<8; \ + buf += 2; \ + break; \ + \ + case VIDEO_PALETTE_RGB24: \ + (r) = buf[0] << 8; (g) = buf[1] << 8; \ + (b) = buf[2] << 8; \ + buf += 3; \ + break; \ + \ + default: \ + fprintf(stderr, \ + "Format %d not yet supported\n", \ + format); \ + } \ +} int get_brightness_adj(unsigned char *image, long size, int *brightness) { long i, tot = 0; @@ -324,40 +324,40 @@ int main(int argc, char ** argv) if(ioctl(fd, VIDIOCSPICT, &vpic) < 0) { vpic.depth=6; if(ioctl(fd, VIDIOCSPICT, &vpic) < 0) { - vpic.depth=4; - if(ioctl(fd, VIDIOCSPICT, &vpic) < 0) { - fprintf(stderr, "Unable to find a supported capture format.\n"); - close(fd); - exit(1); - } + vpic.depth=4; + if(ioctl(fd, VIDIOCSPICT, &vpic) < 0) { + fprintf(stderr, "Unable to find a supported capture format.\n"); + close(fd); + exit(1); + } } } } else { vpic.depth=24; vpic.palette=VIDEO_PALETTE_RGB24; - + if(ioctl(fd, VIDIOCSPICT, &vpic) < 0) { vpic.palette=VIDEO_PALETTE_RGB565; vpic.depth=16; - + if(ioctl(fd, VIDIOCSPICT, &vpic)==-1) { - vpic.palette=VIDEO_PALETTE_RGB555; - vpic.depth=15; - - if(ioctl(fd, VIDIOCSPICT, &vpic)==-1) { - fprintf(stderr, "Unable to find a supported capture format.\n"); - return -1; - } + vpic.palette=VIDEO_PALETTE_RGB555; + vpic.depth=15; + + if(ioctl(fd, VIDIOCSPICT, &vpic)==-1) { + fprintf(stderr, "Unable to find a supported capture format.\n"); + return -1; + } } } } - + buffer = malloc(win.width * win.height * bpp); if (!buffer) { fprintf(stderr, "Out of memory.\n"); exit(1); } - + do { int newbright; read(fd, buffer, win.width * win.height * bpp); @@ -365,8 +365,8 @@ int main(int argc, char ** argv) if (f) { vpic.brightness += (newbright << 8); if(ioctl(fd, VIDIOCSPICT, &vpic)==-1) { - perror("VIDIOSPICT"); - break; + perror("VIDIOSPICT"); + break; } } } while (f); @@ -381,7 +381,7 @@ int main(int argc, char ** argv) fputc(g>>8, stdout); fputc(b>>8, stdout); } - + close(fd); return 0; } diff --git a/Documentation/video4linux/README.cpia b/Documentation/video4linux/README.cpia index c95e7bbc0fd..19cd3bf2498 100644 --- a/Documentation/video4linux/README.cpia +++ b/Documentation/video4linux/README.cpia @@ -87,7 +87,7 @@ hardware configuration of the parport. You can give the boot-parameter at the LILO-prompt or specify it in lilo.conf. I use the following append-line in lilo.conf: - append="parport=0x378,7,3" + append="parport=0x378,7,3" See Documentation/parport.txt for more information about the configuration of the parport and the values given above. Do not simply @@ -175,7 +175,7 @@ THANKS (in no particular order): - Manuel J. Petit de Gabriel for providing help with Isabel (http://isabel.dit.upm.es/) - Bas Huisman for writing the initial parport code -- Jarl Totland for setting up the mailing list +- Jarl Totland for setting up the mailing list and maintaining the web-server[3] - Chris Whiteford for fixes related to the 1.02 firmware diff --git a/Documentation/video4linux/Zoran b/Documentation/video4linux/Zoran index 52c94bd7dca..be9f21b8455 100644 --- a/Documentation/video4linux/Zoran +++ b/Documentation/video4linux/Zoran @@ -28,7 +28,7 @@ Iomega Buz: * Philips saa7111 TV decoder * Philips saa7185 TV encoder Drivers to use: videodev, i2c-core, i2c-algo-bit, - videocodec, saa7111, saa7185, zr36060, zr36067 + videocodec, saa7111, saa7185, zr36060, zr36067 Inputs/outputs: Composite and S-video Norms: PAL, SECAM (720x576 @ 25 fps), NTSC (720x480 @ 29.97 fps) Card number: 7 @@ -39,7 +39,7 @@ Linux Media Labs LML33: * Brooktree bt819 TV decoder * Brooktree bt856 TV encoder Drivers to use: videodev, i2c-core, i2c-algo-bit, - videocodec, bt819, bt856, zr36060, zr36067 + videocodec, bt819, bt856, zr36060, zr36067 Inputs/outputs: Composite and S-video Norms: PAL (720x576 @ 25 fps), NTSC (720x480 @ 29.97 fps) Card number: 5 @@ -50,7 +50,7 @@ Linux Media Labs LML33R10: * Philips saa7114 TV decoder * Analog Devices adv7170 TV encoder Drivers to use: videodev, i2c-core, i2c-algo-bit, - videocodec, saa7114, adv7170, zr36060, zr36067 + videocodec, saa7114, adv7170, zr36060, zr36067 Inputs/outputs: Composite and S-video Norms: PAL (720x576 @ 25 fps), NTSC (720x480 @ 29.97 fps) Card number: 6 @@ -61,7 +61,7 @@ Pinnacle/Miro DC10(new): * Philips saa7110a TV decoder * Analog Devices adv7176 TV encoder Drivers to use: videodev, i2c-core, i2c-algo-bit, - videocodec, saa7110, adv7175, zr36060, zr36067 + videocodec, saa7110, adv7175, zr36060, zr36067 Inputs/outputs: Composite, S-video and Internal Norms: PAL, SECAM (768x576 @ 25 fps), NTSC (640x480 @ 29.97 fps) Card number: 1 @@ -84,7 +84,7 @@ Pinnacle/Miro DC10(old): * * Micronas vpx3220a TV decoder * mse3000 TV encoder or Analog Devices adv7176 TV encoder * Drivers to use: videodev, i2c-core, i2c-algo-bit, - videocodec, vpx3220, mse3000/adv7175, zr36050, zr36016, zr36067 + videocodec, vpx3220, mse3000/adv7175, zr36050, zr36016, zr36067 Inputs/outputs: Composite, S-video and Internal Norms: PAL, SECAM (768x576 @ 25 fps), NTSC (640x480 @ 29.97 fps) Card number: 0 @@ -96,7 +96,7 @@ Pinnacle/Miro DC30: * * Micronas vpx3225d/vpx3220a/vpx3216b TV decoder * Analog Devices adv7176 TV encoder Drivers to use: videodev, i2c-core, i2c-algo-bit, - videocodec, vpx3220/vpx3224, adv7175, zr36050, zr36016, zr36067 + videocodec, vpx3220/vpx3224, adv7175, zr36050, zr36016, zr36067 Inputs/outputs: Composite, S-video and Internal Norms: PAL, SECAM (768x576 @ 25 fps), NTSC (640x480 @ 29.97 fps) Card number: 3 @@ -123,11 +123,11 @@ Note: use encoder=X or decoder=X for non-default i2c chips (see i2c-id.h) The best know TV standards are NTSC/PAL/SECAM. but for decoding a frame that information is not enough. There are several formats of the TV standards. -And not every TV decoder is able to handle every format. Also the every -combination is supported by the driver. There are currently 11 different -tv broadcast formats all aver the world. +And not every TV decoder is able to handle every format. Also the every +combination is supported by the driver. There are currently 11 different +tv broadcast formats all aver the world. -The CCIR defines parameters needed for broadcasting the signal. +The CCIR defines parameters needed for broadcasting the signal. The CCIR has defined different standards: A,B,D,E,F,G,D,H,I,K,K1,L,M,N,... The CCIR says not much about about the colorsystem used !!! And talking about a colorsystem says not to much about how it is broadcast. @@ -136,18 +136,18 @@ The CCIR standards A,E,F are not used any more. When you speak about NTSC, you usually mean the standard: CCIR - M using the NTSC colorsystem which is used in the USA, Japan, Mexico, Canada -and a few others. +and a few others. When you talk about PAL, you usually mean: CCIR - B/G using the PAL -colorsystem which is used in many Countries. +colorsystem which is used in many Countries. -When you talk about SECAM, you mean: CCIR - L using the SECAM Colorsystem +When you talk about SECAM, you mean: CCIR - L using the SECAM Colorsystem which is used in France, and a few others. There the other version of SECAM, CCIR - D/K is used in Bulgaria, China, -Slovakai, Hungary, Korea (Rep.), Poland, Rumania and a others. +Slovakai, Hungary, Korea (Rep.), Poland, Rumania and a others. -The CCIR - H uses the PAL colorsystem (sometimes SECAM) and is used in +The CCIR - H uses the PAL colorsystem (sometimes SECAM) and is used in Egypt, Libya, Sri Lanka, Syrain Arab. Rep. The CCIR - I uses the PAL colorsystem, and is used in Great Britain, Hong Kong, @@ -158,30 +158,30 @@ and is used in Argentinia, Uruguay, an a few others We do not talk about how the audio is broadcast ! -A rather good sites about the TV standards are: +A rather good sites about the TV standards are: http://www.sony.jp/ServiceArea/Voltage_map/ http://info.electronicwerkstatt.de/bereiche/fernsehtechnik/frequenzen_und_normen/Fernsehnormen/ and http://www.cabl.com/restaurant/channel.html Other weird things around: NTSC 4.43 is a modificated NTSC, which is mainly used in PAL VCR's that are able to play back NTSC. PAL 60 seems to be the same -as NTSC 4.43 . The Datasheets also talk about NTSC 44, It seems as if it would -be the same as NTSC 4.43. +as NTSC 4.43 . The Datasheets also talk about NTSC 44, It seems as if it would +be the same as NTSC 4.43. NTSC Combs seems to be a decoder mode where the decoder uses a comb filter to split coma and luma instead of a Delay line. But I did not defiantly find out what NTSC Comb is. Philips saa7111 TV decoder -was introduced in 1997, is used in the BUZ and -can handle: PAL B/G/H/I, PAL N, PAL M, NTSC M, NTSC N, NTSC 4.43 and SECAM +was introduced in 1997, is used in the BUZ and +can handle: PAL B/G/H/I, PAL N, PAL M, NTSC M, NTSC N, NTSC 4.43 and SECAM Philips saa7110a TV decoder was introduced in 1995, is used in the Pinnacle/Miro DC10(new), DC10+ and -can handle: PAL B/G, NTSC M and SECAM +can handle: PAL B/G, NTSC M and SECAM Philips saa7114 TV decoder -was introduced in 2000, is used in the LML33R10 and +was introduced in 2000, is used in the LML33R10 and can handle: PAL B/G/D/H/I/N, PAL N, PAL M, NTSC M, NTSC 4.43 and SECAM Brooktree bt819 TV decoder @@ -206,7 +206,7 @@ was introduced in 1996, is used in the BUZ can generate: PAL B/G, NTSC M Brooktree bt856 TV Encoder -was introduced in 1994, is used in the LML33 +was introduced in 1994, is used in the LML33 can generate: PAL B/D/G/H/I/N, PAL M, NTSC M, PAL-N (Argentina) Analog Devices adv7170 TV Encoder @@ -221,9 +221,9 @@ ITT mse3000 TV encoder was introduced in 1991, is used in the DC10 old can generate: PAL , NTSC , SECAM -The adv717x, should be able to produce PAL N. But you find nothing PAL N +The adv717x, should be able to produce PAL N. But you find nothing PAL N specific in the registers. Seem that you have to reuse a other standard -to generate PAL N, maybe it would work if you use the PAL M settings. +to generate PAL N, maybe it would work if you use the PAL M settings. ========================== @@ -261,7 +261,7 @@ Here's my experience of using LML33 and Buz on various motherboards: VIA MVP3 Forget it. Pointless. Doesn't work. -Intel 430FX (Pentium 200) +Intel 430FX (Pentium 200) LML33 perfect, Buz tolerable (3 or 4 frames dropped per movie) Intel 440BX (early stepping) LML33 tolerable. Buz starting to get annoying (6-10 frames/hour) @@ -438,52 +438,52 @@ importance of buffer sizes: > -q 25 -b 128 : 24.655.992 > -q 25 -b 256 : 25.859.820 -I woke up, and can't go to sleep again. I'll kill some time explaining why +I woke up, and can't go to sleep again. I'll kill some time explaining why this doesn't look strange to me. -Let's do some math using a width of 704 pixels. I'm not sure whether the Buz +Let's do some math using a width of 704 pixels. I'm not sure whether the Buz actually use that number or not, but that's not too important right now. -704x288 pixels, one field, is 202752 pixels. Divided by 64 pixels per block; -3168 blocks per field. Each pixel consist of two bytes; 128 bytes per block; -1024 bits per block. 100% in the new driver mean 1:2 compression; the maximum -output becomes 512 bits per block. Actually 510, but 512 is simpler to use +704x288 pixels, one field, is 202752 pixels. Divided by 64 pixels per block; +3168 blocks per field. Each pixel consist of two bytes; 128 bytes per block; +1024 bits per block. 100% in the new driver mean 1:2 compression; the maximum +output becomes 512 bits per block. Actually 510, but 512 is simpler to use for calculations. -Let's say that we specify d1q50. We thus want 256 bits per block; times 3168 -becomes 811008 bits; 101376 bytes per field. We're talking raw bits and bytes -here, so we don't need to do any fancy corrections for bits-per-pixel or such +Let's say that we specify d1q50. We thus want 256 bits per block; times 3168 +becomes 811008 bits; 101376 bytes per field. We're talking raw bits and bytes +here, so we don't need to do any fancy corrections for bits-per-pixel or such things. 101376 bytes per field. -d1 video contains two fields per frame. Those sum up to 202752 bytes per +d1 video contains two fields per frame. Those sum up to 202752 bytes per frame, and one of those frames goes into each buffer. -But wait a second! -b128 gives 128kB buffers! It's not possible to cram +But wait a second! -b128 gives 128kB buffers! It's not possible to cram 202752 bytes of JPEG data into 128kB! -This is what the driver notice and automatically compensate for in your +This is what the driver notice and automatically compensate for in your examples. Let's do some math using this information: -128kB is 131072 bytes. In this buffer, we want to store two fields, which -leaves 65536 bytes for each field. Using 3168 blocks per field, we get -20.68686868... available bytes per block; 165 bits. We can't allow the -request for 256 bits per block when there's only 165 bits available! The -q50 -option is silently overridden, and the -b128 option takes precedence, leaving +128kB is 131072 bytes. In this buffer, we want to store two fields, which +leaves 65536 bytes for each field. Using 3168 blocks per field, we get +20.68686868... available bytes per block; 165 bits. We can't allow the +request for 256 bits per block when there's only 165 bits available! The -q50 +option is silently overridden, and the -b128 option takes precedence, leaving us with the equivalence of -q32. -This gives us a data rate of 165 bits per block, which, times 3168, sums up -to 65340 bytes per field, out of the allowed 65536. The current driver has -another level of rate limiting; it won't accept -q values that fill more than -6/8 of the specified buffers. (I'm not sure why. "Playing it safe" seem to be -a safe bet. Personally, I think I would have lowered requested-bits-per-block -by one, or something like that.) We can't use 165 bits per block, but have to -lower it again, to 6/8 of the available buffer space: We end up with 124 bits -per block, the equivalence of -q24. With 128kB buffers, you can't use greater +This gives us a data rate of 165 bits per block, which, times 3168, sums up +to 65340 bytes per field, out of the allowed 65536. The current driver has +another level of rate limiting; it won't accept -q values that fill more than +6/8 of the specified buffers. (I'm not sure why. "Playing it safe" seem to be +a safe bet. Personally, I think I would have lowered requested-bits-per-block +by one, or something like that.) We can't use 165 bits per block, but have to +lower it again, to 6/8 of the available buffer space: We end up with 124 bits +per block, the equivalence of -q24. With 128kB buffers, you can't use greater than -q24 at -d1. (And PAL, and 704 pixels width...) -The third example is limited to -q24 through the same process. The second -example, using very similar calculations, is limited to -q48. The only -example that actually grab at the specified -q value is the last one, which +The third example is limited to -q24 through the same process. The second +example, using very similar calculations, is limited to -q48. The only +example that actually grab at the specified -q value is the last one, which is clearly visible, looking at the file size. -- diff --git a/Documentation/video4linux/bttv/ICs b/Documentation/video4linux/bttv/ICs index 6b749133696..611315f87c3 100644 --- a/Documentation/video4linux/bttv/ICs +++ b/Documentation/video4linux/bttv/ICs @@ -14,13 +14,13 @@ Hauppauge Win/TV pci (version 405): Microchip 24LC02B or Philips 8582E2Y: 256 Byte EEPROM with configuration information - I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf) + I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf) Philips SAA5246AGP/E: Videotext decoder chip, I2C 0x22-0x23 TDA9800: sound decoder Winbond W24257AS-35: 32Kx8 CMOS static RAM (Videotext buffer mem) 14052B: analog switch for selection of sound source -PAL: +PAL: TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3 diff --git a/Documentation/video4linux/bttv/PROBLEMS b/Documentation/video4linux/bttv/PROBLEMS index 8e31e9e36bf..2b8b0079f7c 100644 --- a/Documentation/video4linux/bttv/PROBLEMS +++ b/Documentation/video4linux/bttv/PROBLEMS @@ -3,7 +3,7 @@ - Start capturing by pressing "c" or by selecting it via a menu!!! - The memory of some S3 cards is not recognized right: - + First of all, if you are not using XFree-3.2 or newer, upgrade AT LEAST to XFree-3.2A! This solved the problem for most people. @@ -31,23 +31,23 @@ (mostly with Trio 64 but also with some others) Get the free demo version of Accelerated X from www.xinside.com and try bttv with it. bttv seems to work with most S3 cards with Accelerated X. - + Since I do not know much (better make that almost nothing) about VGA card programming I do not know the reason for this. Looks like XFree does something different when setting up the video memory? - Maybe somebody can enlighten me? - Would be nice if somebody could get this to work with XFree since - Accelerated X costs more than some of the grabber cards ... - + Maybe somebody can enlighten me? + Would be nice if somebody could get this to work with XFree since + Accelerated X costs more than some of the grabber cards ... + Better linear frame buffer support for S3 cards will probably be in XFree 4.0. - + - Grabbing is not switched off when changing consoles with XFree. That's because XFree and some AcceleratedX versions do not send unmap events. - Some popup windows (e.g. of the window manager) are not refreshed. - + Disable backing store by starting X with the option "-bs" - When using 32 bpp in XFree or 24+8bpp mode in AccelX 3.1 the system diff --git a/Documentation/video4linux/bttv/README.quirks b/Documentation/video4linux/bttv/README.quirks index e8edb87df71..92e03929a6b 100644 --- a/Documentation/video4linux/bttv/README.quirks +++ b/Documentation/video4linux/bttv/README.quirks @@ -38,9 +38,9 @@ tolerate. ------------------------ When using the 430FX PCI, the following rules will ensure -compatibility: +compatibility: - (1) Deassert REQ at the same time as asserting FRAME. + (1) Deassert REQ at the same time as asserting FRAME. (2) Do not reassert REQ to request another bus transaction until after finish-ing the previous transaction. diff --git a/Documentation/video4linux/bttv/THANKS b/Documentation/video4linux/bttv/THANKS index 2085399da7d..950aa781c2e 100644 --- a/Documentation/video4linux/bttv/THANKS +++ b/Documentation/video4linux/bttv/THANKS @@ -1,6 +1,6 @@ Many thanks to: -- Markus Schroeder for information on the Bt848 +- Markus Schroeder for information on the Bt848 and tuner programming and his control program xtvc. - Martin Buck for his great Videotext @@ -16,7 +16,7 @@ Many thanks to: - MIRO for providing a free PCTV card and detailed information about the components on their cards. (E.g. how the tuner type is detected) Without their card I could not have debugged the NTSC mode. - + - Hauppauge for telling how the sound input is selected and what components they do and will use on their radio cards. Also many thanks for faxing me the FM1216 data sheet. diff --git a/Documentation/video4linux/radiotrack.txt b/Documentation/video4linux/radiotrack.txt index 2b75345f13e..d1f3ed19918 100644 --- a/Documentation/video4linux/radiotrack.txt +++ b/Documentation/video4linux/radiotrack.txt @@ -131,17 +131,17 @@ Check Stereo: BASE <-- 0xd8 (current volume, stereo detect, x=0xff ==> "not stereo", x=0xfd ==> "stereo detected" Set Frequency: code = (freq*40) + 10486188 - foreach of the 24 bits in code, - (from Least to Most Significant): - to write a "zero" bit, - BASE <-- 0x01 (audio mute, no stereo detect, radio + foreach of the 24 bits in code, + (from Least to Most Significant): + to write a "zero" bit, + BASE <-- 0x01 (audio mute, no stereo detect, radio disable, "zero" bit phase 1, tuner adjust) - BASE <-- 0x03 (audio mute, no stereo detect, radio + BASE <-- 0x03 (audio mute, no stereo detect, radio disable, "zero" bit phase 2, tuner adjust) - to write a "one" bit, - BASE <-- 0x05 (audio mute, no stereo detect, radio + to write a "one" bit, + BASE <-- 0x05 (audio mute, no stereo detect, radio disable, "one" bit phase 1, tuner adjust) - BASE <-- 0x07 (audio mute, no stereo detect, radio + BASE <-- 0x07 (audio mute, no stereo detect, radio disable, "one" bit phase 2, tuner adjust) ---------------------------------------------------------------------------- diff --git a/Documentation/video4linux/w9966.txt b/Documentation/video4linux/w9966.txt index e7ac33a7eb0..78a651254b8 100644 --- a/Documentation/video4linux/w9966.txt +++ b/Documentation/video4linux/w9966.txt @@ -26,7 +26,7 @@ is called VIDEO_PALETTE_YUV422 (16 bpp). A minimal test application (with source) is available from: http://hem.fyristorg.com/mogul/w9966.html -The slow framerate is due to missing DMA ECP read support in the +The slow framerate is due to missing DMA ECP read support in the parport drivers. I might add working EPP support later. Good luck! diff --git a/Documentation/video4linux/zr36120.txt b/Documentation/video4linux/zr36120.txt index 5d6357eefde..ac6d92d0194 100644 --- a/Documentation/video4linux/zr36120.txt +++ b/Documentation/video4linux/zr36120.txt @@ -2,7 +2,7 @@ Driver for Trust Computer Products Framegrabber, version 0.6.1 ------ --- ----- -------- -------- ------------ ------- - - - - ZORAN ------------------------------------------------------ - Author: Pauline Middelink + Author: Pauline Middelink Date: 18 September 1999 Version: 0.6.1 @@ -115,7 +115,7 @@ After making/checking the devices do: is the cardtype of the card you have. The cardnumber can be found in the source of zr36120. Look for tvcards. If your card is not there, please try if any other card gives some -response, and mail me if you got a working tvcard addition. +response, and mail me if you got a working tvcard addition. PS.