From f68d9320cd06fdec19735143b42e5197b63165b4 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Mon, 26 Mar 2007 23:03:18 +0200 Subject: ide: revert "ide: fix drive side 80c cable check, take 2" for now "ide: fix drive side 80c cable check, take 2" patch from Tejun Heo (commit fab59375b9543f84d1714f7dd00f5d11e531bd3e) fixed 80c bit test (bit13 of word93) but we also need to fix master/slave IDENTIFY order (slave device should be probed first in order to make it release PDIAG- signal) and we should also check for pre-ATA3 slave devices (which may not release PDIAG- signal). [ Unfortunately the fact that IDE driver doesn't reset devices itself helps only a bit as it seems that some BIOS-es reset ATA devices after programming the chipset, some BIOS-es can be set to not probe/configure selected devices, there may be no BIOS in case of add-on cards etc. ] Since we are quite late in the release cycle and the required changes will affect a lot of systems just revert the fix for now. [ Please also see libata commit f31f0cc2f0b7527072d94d02da332d9bb8d7d94c. ] Thanks goes out to Fernando Mitio Yamada for reporting the problem and patiently testing patches. Acked-by: Tejun Heo Cc: Alan Cox Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/ide-iops.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c index bd513f5a232..5523c52fee7 100644 --- a/drivers/ide/ide-iops.c +++ b/drivers/ide/ide-iops.c @@ -583,8 +583,12 @@ u8 eighty_ninty_three (ide_drive_t *drive) if(!(drive->id->hw_config & 0x4000)) return 0; #endif /* CONFIG_IDEDMA_IVB */ - if (!(drive->id->hw_config & 0x2000)) - return 0; + /* + * FIXME: + * - change master/slave IDENTIFY order + * - force bit13 (80c cable present) check + * (unless the slave device is pre-ATA3) + */ return 1; } -- cgit v1.2.3 From 8799620400b0b1a4729d8be828b5bfb3d2a8db1a Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Mon, 26 Mar 2007 23:03:19 +0200 Subject: ide: fix locking for manual DMA enable/disable ("hdparm -d") Since hwif->ide_dma_check and hwif->ide_dma_on never queue any commands (ide_config_drive_speed() sets transfer mode using polling and has no error recovery) we are safe with setting hwgroup->busy for the time while DMA setting for a drive is changed (so it won't race against I/O commands in fly). I audited briefly all ->ide_dma_check/->ide_dma_on/->tuneproc/->speedproc implementations and they all look OK wrt to this change. This patch finally allowed me to close kernel bugzilla bug #8169 (once again thanks to Patrick Horn for reporting the issue & testing patches). Cc: Sergei Shtylyov Cc: Alan Cox Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/ide.c | 37 ++++++++++++++++++++++++++++++------- 1 file changed, 30 insertions(+), 7 deletions(-) diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c index 695610f0e3e..a6f098fda88 100644 --- a/drivers/ide/ide.c +++ b/drivers/ide/ide.c @@ -1124,17 +1124,40 @@ static int set_io_32bit(ide_drive_t *drive, int arg) static int set_using_dma (ide_drive_t *drive, int arg) { #ifdef CONFIG_BLK_DEV_IDEDMA + ide_hwif_t *hwif = drive->hwif; + int err = -EPERM; + if (!drive->id || !(drive->id->capability & 1)) - return -EPERM; - if (HWIF(drive)->ide_dma_check == NULL) - return -EPERM; + goto out; + + if (hwif->ide_dma_check == NULL) + goto out; + + err = -EBUSY; + if (ide_spin_wait_hwgroup(drive)) + goto out; + /* + * set ->busy flag, unlock and let it ride + */ + hwif->hwgroup->busy = 1; + spin_unlock_irq(&ide_lock); + + err = 0; + if (arg) { - if (ide_set_dma(drive)) - return -EIO; - if (HWIF(drive)->ide_dma_on(drive)) return -EIO; + if (ide_set_dma(drive) || hwif->ide_dma_on(drive)) + err = -EIO; } else ide_dma_off(drive); - return 0; + + /* + * lock, clear ->busy flag and unlock before leaving + */ + spin_lock_irq(&ide_lock); + hwif->hwgroup->busy = 0; + spin_unlock_irq(&ide_lock); +out: + return err; #else return -EPERM; #endif -- cgit v1.2.3 From b43c5f3dbe0c93dc205a7c69f892b94b7037d862 Mon Sep 17 00:00:00 2001 From: Patrick Ringl Date: Mon, 26 Mar 2007 23:03:19 +0200 Subject: ide: cosmetic adaption of drivers/ide/Kconfig concerning SATA Since especially Serial ATA has it's own menu point now, I guess we can change the description of the deprecated SATA driver as well, since the new libATA subsystem is not configured through a SCSI low-level driver anymore, but has it's own menu point. From: Patrick Ringl Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/Kconfig | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index 8f1fd017679..ca2e4f830c3 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -103,8 +103,10 @@ config BLK_DEV_IDE_SATA ---help--- There are two drivers for Serial ATA controllers. - The main driver, "libata", exists inside the SCSI subsystem - and supports most modern SATA controllers. + The main driver, "libata", uses the SCSI subsystem + and supports most modern SATA controllers. In order to use it + you may take a look at "Serial ATA (prod) and Parallel ATA + (experimental) drivers". The IDE driver (which you are currently configuring) supports a few first-generation SATA controllers. -- cgit v1.2.3 From 362ebd83adb4ff2761b6f49a3570f501c3c7e467 Mon Sep 17 00:00:00 2001 From: Albert Lee Date: Mon, 26 Mar 2007 23:03:19 +0200 Subject: pdc202xx_new: Enable ATAPI DMA [ bart: the ressurection of 2 years old patch which slipped thru the cracks (thanks to Sergei Shtylyov for finding it) ] These is the patch to turn on pdc202xx_new for ATAPI DMA. When testing, it works fine without the (request_bufflen % 256) workaround as needed in libata. ide-scsi filters out (pc->request_transfer % 1024) and use PIO, so the pdc202xx ATAPI DMA problem is avoid. Both ide-cd and ide-scsi won't hit the ATAPI DMA problem on pdc202xx_new. Signed-off-by: Albert Lee Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/pci/pdc202xx_new.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c index 6ceb25bc5a7..ace98929cc3 100644 --- a/drivers/ide/pci/pdc202xx_new.c +++ b/drivers/ide/pci/pdc202xx_new.c @@ -255,7 +255,7 @@ static int config_chipset_for_dma(ide_drive_t *drive) printk(KERN_WARNING "%s reduced to Ultra33 mode.\n", drive->name); } - if (drive->media != ide_disk) + if (drive->media != ide_disk && drive->media != ide_cdrom) return 0; if (id->capability & 4) { @@ -545,6 +545,7 @@ static void __devinit init_hwif_pdc202new(ide_hwif_t *hwif) hwif->drives[0].autotune = hwif->drives[1].autotune = 1; + hwif->atapi_dma = 1; hwif->ultra_mask = 0x7f; hwif->mwdma_mask = 0x07; -- cgit v1.2.3 From 513daadd152ddbf32cb6d0447ddba3427ce5b8e8 Mon Sep 17 00:00:00 2001 From: Suleiman Souhlal Date: Mon, 26 Mar 2007 23:03:20 +0200 Subject: ide: use correct IDE error recovery MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set. This violates the ATA spec (can only send IDLE IMMEDIATE when drive is not busy) and really hoses up some drives (modern drives will not be able to recover using this error handling). The correct thing to do is issue a SRST followed by a SET FEATURES command. This is what Western Digital recommends for error recovery and what Western Digital says Windows does.  It also does not violate the ATA spec as far as I can tell. Bart: * port the patch over the current tree * undo the recalibration code removal * send SET FEATURES command after checking for good drive status * don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK} type because we need to send SET FEATURES before handling any requests * some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before other commands (except IDENTIFY) so send SET FEATURES only if there are no pending drive->special requests * update comments and patch description * any bugs introduced by this patch are mine and not Suleiman's :-) Signed-off-by: Suleiman Souhlal Acked-by: Alan Cox Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/ide-io.c | 32 +++++++++++++++++++++----------- drivers/ide/ide-iops.c | 3 +++ include/linux/ide.h | 1 + 3 files changed, 25 insertions(+), 11 deletions(-) diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c index c193553f6fe..0e0280076fc 100644 --- a/drivers/ide/ide-io.c +++ b/drivers/ide/ide-io.c @@ -519,21 +519,24 @@ static ide_startstop_t ide_ata_error(ide_drive_t *drive, struct request *rq, u8 if ((stat & DRQ_STAT) && rq_data_dir(rq) == READ && hwif->err_stops_fifo == 0) try_to_flush_leftover_data(drive); + if (rq->errors >= ERROR_MAX || blk_noretry_request(rq)) { + ide_kill_rq(drive, rq); + return ide_stopped; + } + if (hwif->INB(IDE_STATUS_REG) & (BUSY_STAT|DRQ_STAT)) - /* force an abort */ - hwif->OUTB(WIN_IDLEIMMEDIATE, IDE_COMMAND_REG); + rq->errors |= ERROR_RESET; - if (rq->errors >= ERROR_MAX || blk_noretry_request(rq)) - ide_kill_rq(drive, rq); - else { - if ((rq->errors & ERROR_RESET) == ERROR_RESET) { - ++rq->errors; - return ide_do_reset(drive); - } - if ((rq->errors & ERROR_RECAL) == ERROR_RECAL) - drive->special.b.recalibrate = 1; + if ((rq->errors & ERROR_RESET) == ERROR_RESET) { ++rq->errors; + return ide_do_reset(drive); } + + if ((rq->errors & ERROR_RECAL) == ERROR_RECAL) + drive->special.b.recalibrate = 1; + + ++rq->errors; + return ide_stopped; } @@ -1025,6 +1028,13 @@ static ide_startstop_t start_request (ide_drive_t *drive, struct request *rq) if (!drive->special.all) { ide_driver_t *drv; + /* + * We reset the drive so we need to issue a SETFEATURES. + * Do it _after_ do_special() restored device parameters. + */ + if (drive->current_speed == 0xff) + ide_config_drive_speed(drive, drive->desired_speed); + if (rq->cmd_type == REQ_TYPE_ATA_CMD || rq->cmd_type == REQ_TYPE_ATA_TASK || rq->cmd_type == REQ_TYPE_ATA_TASKFILE) diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c index 5523c52fee7..1ee53a551c3 100644 --- a/drivers/ide/ide-iops.c +++ b/drivers/ide/ide-iops.c @@ -1094,6 +1094,9 @@ static void pre_reset(ide_drive_t *drive) if (HWIF(drive)->pre_reset != NULL) HWIF(drive)->pre_reset(drive); + if (drive->current_speed != 0xff) + drive->desired_speed = drive->current_speed; + drive->current_speed = 0xff; } /* diff --git a/include/linux/ide.h b/include/linux/ide.h index 34f2676b3c6..58564a19986 100644 --- a/include/linux/ide.h +++ b/include/linux/ide.h @@ -615,6 +615,7 @@ typedef struct ide_drive_s { u8 init_speed; /* transfer rate set at boot */ u8 pio_speed; /* unused by core, used by some drivers for fallback from DMA */ u8 current_speed; /* current transfer rate set */ + u8 desired_speed; /* desired transfer rate set */ u8 dn; /* now wide spread use */ u8 wcache; /* status of write cache */ u8 acoustic; /* acoustic management */ -- cgit v1.2.3