From 37b12dd2b07b4d7dc222a5f7f88b25cec532b2aa Mon Sep 17 00:00:00 2001 From: Larry Finger Date: Wed, 4 Nov 2009 00:00:25 -0600 Subject: rtl8187: Fix kernel oops when device is removed when LEDS enabled As reported by Rick Farina (sidhayn@gmail.com), removing the RTL8187 USB stick, or unloading the driver rtl8187 using rmmod will cause a kernel oops. There are at least two forms of the failure, (1) BUG: Scheduling while atomic, and (2) a fatal kernel page fault. This problem is reported in Bugzilla #14539. This problem does not occur for kernel 2.6.31, but does for 2.6.32-rc2, thus it is technically a regression; however, bisection did not locate any faulty patch. The fix was found by comparing the faulty code in rtl8187 with p54usb. My interpretation is that the handling of work queues in mac80211 changed enough to the LEDs to be unregistered before tasks on the work queues are cancelled. Previously, these actions could be done in either order. (Herton Ronaldo Krzesinski reports that the code is the same in 2.6.31, so this may be a candidate for 2.6.31.x. -- JWL) Signed-off-by: Larry Finger Reported-by: Rick Farina Tested-by: Rick Farina Cc: stable@kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/rtl818x/rtl8187_leds.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/rtl818x/rtl8187_leds.c b/drivers/net/wireless/rtl818x/rtl8187_leds.c index a1c670fc155..cf8a4a40fdf 100644 --- a/drivers/net/wireless/rtl818x/rtl8187_leds.c +++ b/drivers/net/wireless/rtl818x/rtl8187_leds.c @@ -210,10 +210,10 @@ void rtl8187_leds_exit(struct ieee80211_hw *dev) /* turn the LED off before exiting */ ieee80211_queue_delayed_work(dev, &priv->led_off, 0); - cancel_delayed_work_sync(&priv->led_off); - cancel_delayed_work_sync(&priv->led_on); rtl8187_unregister_led(&priv->led_rx); rtl8187_unregister_led(&priv->led_tx); + cancel_delayed_work_sync(&priv->led_off); + cancel_delayed_work_sync(&priv->led_on); } #endif /* def CONFIG_RTL8187_LED */ -- cgit v1.2.3 From 143d40f3ab8fbd8ca2fe712ec8e072d687142804 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Fri, 6 Nov 2009 12:58:20 -0500 Subject: Revert "ipw2200: fix oops on missing firmware" This reverts commit e6c5fc53d0f44a772398402ee8a1879818e42b4e. Based on this regression report: Date: Thu, 05 Nov 2009 15:59:16 +0100 From: Holger Schurig To: linux-wireless@vger.kernel.org Subject: BUG: oops when "rmmod ipw2200" This happened on wireless-testing v2.6.32-rc6-41575-g5e68bfb. I modprobed ipw2200, put it into monitor mode, used tshark a while to monitor, then I stopped tshark, "ifconfig eth2 down" and finally "rmmod ipw2200", and voila: [ 917.189620] ------------[ cut here ]------------ [ 917.189717] kernel BUG at net/wireless/core.c:543! [ 917.189805] invalid opcode: 0000 [#1] PREEMPT SMP [ 917.190002] last sysfs file: /sys/devices/pci0000:00/0000:00:1e.0/0000:02:0d.0/firmware/0000:02:0d.0/loading [ 917.190136] Modules linked in: lib80211_crypt_wep ipw2200(-) libipw lib80211 ath5k mac80211 ath cfg80211 psmouse uhci_hcd [ 917.190680] [ 917.190759] Pid: 1763, comm: rmmod Not tainted (2.6.32-rc6-wl #26) Amilo M1425 [ 917.190886] EIP: 0060:[] EFLAGS: 00010202 CPU: 0 [ 917.190992] EIP is at wiphy_unregister+0xd3/0x175 [cfg80211] [ 917.191083] EAX: f601d4c4 EBX: 00000000 ECX: 00000000 EDX: f79e8600 [ 917.191176] ESI: f601d400 EDI: f95b4350 EBP: f6009eb4 ESP: f6009e8c [ 917.191269] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 917.191360] Process rmmod (pid: 1763, ti=f6008000 task=f79e8130 task.ti=f6008000) [ 917.191486] Stack: [ 917.191562] f601d5a0 f601d484 f6460e98 f6009ea0 c01407ee f6009eb8 00000246 f64604c0 [ 917.191916] <0> f6460e5c f95b4350 f6009ec0 f94fd030 f6460e98 f6009edc f95a9d4f f787bc00 [ 917.192100] <0> f787bc58 f787bc00 f95b4350 f95b4350 f6009ee8 c0207fca f787bc58 f6009ef8 [ 917.192100] Call Trace: [ 917.192100] [] ? trace_hardirqs_on+0xb/0xd [ 917.192100] [] ? unregister_ieee80211+0xe/0x27 [libipw] [ 917.192100] [] ? ipw_pci_remove+0x59/0x227 [ipw2200] [ 917.192100] [] ? pci_device_remove+0x19/0x39 [ 917.192100] [] ? __device_release_driver+0x59/0x9d [ 917.192100] [] ? driver_detach+0x67/0x85 [ 917.192100] [] ? bus_remove_driver+0x69/0x85 [ 917.192100] [] ? driver_unregister+0x4d/0x54 [ 917.192100] [] ? pci_unregister_driver+0x28/0x71 [ 917.192100] [] ? ipw_exit+0x1c/0x1e [ipw2200] [ 917.192100] [] ? sys_delete_module+0x192/0x1ef [ 917.192100] [] ? remove_vma+0x52/0x58 [ 917.192100] [] ? sysenter_exit+0xf/0x18 [ 917.192100] [] ? sysenter_do_call+0x12/0x36 [ 917.192100] Code: 74 07 e8 81 bc 8c c7 eb c8 8d 55 e0 89 f8 e8 d6 6d 66 c7 8b 45 dc 31 d2 e8 81 cc 8c c7 8d 86 c4 00 00 00 39 86 c4 00 00 00 74 04 <0f> 0b eb fe 8b 45 dc 8d 5e 0c e8 5a cc 8c c7 8b 86 94 03 00 00 [ 917.192100] EIP: [] wiphy_unregister+0xd3/0x175 [cfg80211] SS:ESP 0068:f6009e8c [ 917.203718] ---[ end trace bcaaf449945a5100 ]--- Signed-off-by: John W. Linville --- drivers/net/wireless/ipw2x00/ipw2100.c | 5 +---- drivers/net/wireless/ipw2x00/ipw2200.c | 2 -- drivers/net/wireless/ipw2x00/libipw.h | 1 - drivers/net/wireless/ipw2x00/libipw_module.c | 14 +++++--------- 4 files changed, 6 insertions(+), 16 deletions(-) diff --git a/drivers/net/wireless/ipw2x00/ipw2100.c b/drivers/net/wireless/ipw2x00/ipw2100.c index a741d37fd96..240cff1e697 100644 --- a/drivers/net/wireless/ipw2x00/ipw2100.c +++ b/drivers/net/wireless/ipw2x00/ipw2100.c @@ -6325,10 +6325,8 @@ static int ipw2100_pci_init_one(struct pci_dev *pci_dev, fail: if (dev) { - if (registered) { - unregister_ieee80211(priv->ieee); + if (registered) unregister_netdev(dev); - } ipw2100_hw_stop_adapter(priv); @@ -6385,7 +6383,6 @@ static void __devexit ipw2100_pci_remove_one(struct pci_dev *pci_dev) /* Unregister the device first - this results in close() * being called if the device is open. If we free storage * first, then close() will crash. */ - unregister_ieee80211(priv->ieee); unregister_netdev(dev); /* ipw2100_down will ensure that there is no more pending work diff --git a/drivers/net/wireless/ipw2x00/ipw2200.c b/drivers/net/wireless/ipw2x00/ipw2200.c index 04341a2a619..8d58e6ed4e7 100644 --- a/drivers/net/wireless/ipw2x00/ipw2200.c +++ b/drivers/net/wireless/ipw2x00/ipw2200.c @@ -11821,7 +11821,6 @@ static int __devinit ipw_pci_probe(struct pci_dev *pdev, if (err) { IPW_ERROR("Failed to register promiscuous network " "device (error %d).\n", err); - unregister_ieee80211(priv->ieee); unregister_netdev(priv->net_dev); goto out_remove_sysfs; } @@ -11872,7 +11871,6 @@ static void __devexit ipw_pci_remove(struct pci_dev *pdev) mutex_unlock(&priv->mutex); - unregister_ieee80211(priv->ieee); unregister_netdev(priv->net_dev); if (priv->rxq) { diff --git a/drivers/net/wireless/ipw2x00/libipw.h b/drivers/net/wireless/ipw2x00/libipw.h index f42ade6c2d3..bf45391172f 100644 --- a/drivers/net/wireless/ipw2x00/libipw.h +++ b/drivers/net/wireless/ipw2x00/libipw.h @@ -1020,7 +1020,6 @@ static inline int libipw_is_cck_rate(u8 rate) /* ieee80211.c */ extern void free_ieee80211(struct net_device *dev, int monitor); extern struct net_device *alloc_ieee80211(int sizeof_priv, int monitor); -extern void unregister_ieee80211(struct libipw_device *ieee); extern int libipw_change_mtu(struct net_device *dev, int new_mtu); extern void libipw_networks_age(struct libipw_device *ieee, diff --git a/drivers/net/wireless/ipw2x00/libipw_module.c b/drivers/net/wireless/ipw2x00/libipw_module.c index be5b809ec97..a0e9f6aed7d 100644 --- a/drivers/net/wireless/ipw2x00/libipw_module.c +++ b/drivers/net/wireless/ipw2x00/libipw_module.c @@ -235,19 +235,16 @@ void free_ieee80211(struct net_device *dev, int monitor) libipw_networks_free(ieee); /* free cfg80211 resources */ - if (!monitor) + if (!monitor) { + wiphy_unregister(ieee->wdev.wiphy); + kfree(ieee->a_band.channels); + kfree(ieee->bg_band.channels); wiphy_free(ieee->wdev.wiphy); + } free_netdev(dev); } -void unregister_ieee80211(struct libipw_device *ieee) -{ - wiphy_unregister(ieee->wdev.wiphy); - kfree(ieee->a_band.channels); - kfree(ieee->bg_band.channels); -} - #ifdef CONFIG_LIBIPW_DEBUG static int debug = 0; @@ -333,4 +330,3 @@ module_init(libipw_init); EXPORT_SYMBOL(alloc_ieee80211); EXPORT_SYMBOL(free_ieee80211); -EXPORT_SYMBOL(unregister_ieee80211); -- cgit v1.2.3 From 66f84d6594729c866c0c03fe97159a987dad7d84 Mon Sep 17 00:00:00 2001 From: Sean Cross Date: Thu, 5 Nov 2009 20:22:03 +0100 Subject: rt2x00: Don't queue ieee80211 work after USB removal MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This prevents the rt2x00 driver from queueing ieee80211 work after the   USB card has been removed, preventing a kernel panic. Signed-off-by: Sean Cross Signed-off-by: Ivo van Doorn Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2x00dev.c | 4 ++-- drivers/net/wireless/rt2x00/rt2x00link.c | 11 +++++++---- drivers/net/wireless/rt2x00/rt2x00usb.c | 9 ++++++++- 3 files changed, 17 insertions(+), 7 deletions(-) diff --git a/drivers/net/wireless/rt2x00/rt2x00dev.c b/drivers/net/wireless/rt2x00/rt2x00dev.c index 71761b34383..73bbec58341 100644 --- a/drivers/net/wireless/rt2x00/rt2x00dev.c +++ b/drivers/net/wireless/rt2x00/rt2x00dev.c @@ -815,6 +815,8 @@ int rt2x00lib_probe_dev(struct rt2x00_dev *rt2x00dev) mutex_init(&rt2x00dev->csr_mutex); + set_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags); + /* * Make room for rt2x00_intf inside the per-interface * structure ieee80211_vif. @@ -871,8 +873,6 @@ int rt2x00lib_probe_dev(struct rt2x00_dev *rt2x00dev) rt2x00leds_register(rt2x00dev); rt2x00debug_register(rt2x00dev); - set_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags); - return 0; exit: diff --git a/drivers/net/wireless/rt2x00/rt2x00link.c b/drivers/net/wireless/rt2x00/rt2x00link.c index c64db0ba7f4..c708d0be915 100644 --- a/drivers/net/wireless/rt2x00/rt2x00link.c +++ b/drivers/net/wireless/rt2x00/rt2x00link.c @@ -362,8 +362,9 @@ void rt2x00link_start_tuner(struct rt2x00_dev *rt2x00dev) rt2x00link_reset_tuner(rt2x00dev, false); - ieee80211_queue_delayed_work(rt2x00dev->hw, - &link->work, LINK_TUNE_INTERVAL); + if (test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) + ieee80211_queue_delayed_work(rt2x00dev->hw, + &link->work, LINK_TUNE_INTERVAL); } void rt2x00link_stop_tuner(struct rt2x00_dev *rt2x00dev) @@ -469,8 +470,10 @@ static void rt2x00link_tuner(struct work_struct *work) * Increase tuner counter, and reschedule the next link tuner run. */ link->count++; - ieee80211_queue_delayed_work(rt2x00dev->hw, - &link->work, LINK_TUNE_INTERVAL); + + if (test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) + ieee80211_queue_delayed_work(rt2x00dev->hw, + &link->work, LINK_TUNE_INTERVAL); } void rt2x00link_register(struct rt2x00_dev *rt2x00dev) diff --git a/drivers/net/wireless/rt2x00/rt2x00usb.c b/drivers/net/wireless/rt2x00/rt2x00usb.c index 501544882c2..f02b48a9059 100644 --- a/drivers/net/wireless/rt2x00/rt2x00usb.c +++ b/drivers/net/wireless/rt2x00/rt2x00usb.c @@ -47,6 +47,8 @@ int rt2x00usb_vendor_request(struct rt2x00_dev *rt2x00dev, (requesttype == USB_VENDOR_REQUEST_IN) ? usb_rcvctrlpipe(usb_dev, 0) : usb_sndctrlpipe(usb_dev, 0); + if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) + return -ENODEV; for (i = 0; i < REGISTER_BUSY_COUNT; i++) { status = usb_control_msg(usb_dev, pipe, request, requesttype, @@ -60,8 +62,10 @@ int rt2x00usb_vendor_request(struct rt2x00_dev *rt2x00dev, * -ENODEV: Device has disappeared, no point continuing. * All other errors: Try again. */ - else if (status == -ENODEV) + else if (status == -ENODEV) { + clear_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags); break; + } } ERROR(rt2x00dev, @@ -161,6 +165,9 @@ int rt2x00usb_regbusy_read(struct rt2x00_dev *rt2x00dev, { unsigned int i; + if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) + return -ENODEV; + for (i = 0; i < REGISTER_BUSY_COUNT; i++) { rt2x00usb_register_read_lock(rt2x00dev, offset, reg); if (!rt2x00_get_field32(*reg, field)) -- cgit v1.2.3 From 539054a8fa5141c9a4e9ac6a86d249e3f2bdef45 Mon Sep 17 00:00:00 2001 From: Jan Engelhardt Date: Fri, 6 Nov 2009 18:08:32 -0800 Subject: netfilter: xt_connlimit: fix regression caused by zero family value Commit v2.6.28-rc1~717^2~109^2~2 was slightly incomplete; not all instances of par->match->family were changed to par->family. References: http://bugzilla.netfilter.org/show_bug.cgi?id=610 Signed-off-by: Jan Engelhardt Signed-off-by: Patrick McHardy Signed-off-by: David S. Miller --- net/netfilter/xt_connlimit.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) diff --git a/net/netfilter/xt_connlimit.c b/net/netfilter/xt_connlimit.c index 68098095439..38f03f75a63 100644 --- a/net/netfilter/xt_connlimit.c +++ b/net/netfilter/xt_connlimit.c @@ -103,7 +103,7 @@ static int count_them(struct xt_connlimit_data *data, const struct nf_conntrack_tuple *tuple, const union nf_inet_addr *addr, const union nf_inet_addr *mask, - const struct xt_match *match) + u_int8_t family) { const struct nf_conntrack_tuple_hash *found; struct xt_connlimit_conn *conn; @@ -113,8 +113,7 @@ static int count_them(struct xt_connlimit_data *data, bool addit = true; int matches = 0; - - if (match->family == NFPROTO_IPV6) + if (family == NFPROTO_IPV6) hash = &data->iphash[connlimit_iphash6(addr, mask)]; else hash = &data->iphash[connlimit_iphash(addr->ip & mask->ip)]; @@ -157,8 +156,7 @@ static int count_them(struct xt_connlimit_data *data, continue; } - if (same_source_net(addr, mask, &conn->tuple.src.u3, - match->family)) + if (same_source_net(addr, mask, &conn->tuple.src.u3, family)) /* same source network -> be counted! */ ++matches; nf_ct_put(found_ct); @@ -207,7 +205,7 @@ connlimit_mt(const struct sk_buff *skb, const struct xt_match_param *par) spin_lock_bh(&info->data->lock); connections = count_them(info->data, tuple_ptr, &addr, - &info->mask, par->match); + &info->mask, par->family); spin_unlock_bh(&info->data->lock); if (connections < 0) { -- cgit v1.2.3 From 9e90c961134929678022aee0c68b16c1ed520614 Mon Sep 17 00:00:00 2001 From: Ajit Khaparde Date: Fri, 6 Nov 2009 02:06:59 +0000 Subject: be2net: fix to set proper flow control on resume If be2 goes into suspend after a user changes the flow control settings, we are not programming them back after resume. This patch takes care of it. We now get the flow control settings before going to suspend mode and then apply them during resume. Signed-off-by: Ajit Khaparde Signed-off-by: David S. Miller --- drivers/net/benet/be.h | 2 ++ drivers/net/benet/be_ethtool.c | 8 +++++--- drivers/net/benet/be_main.c | 8 +++++++- 3 files changed, 14 insertions(+), 4 deletions(-) diff --git a/drivers/net/benet/be.h b/drivers/net/benet/be.h index a80da0e14a5..3b79a225628 100644 --- a/drivers/net/benet/be.h +++ b/drivers/net/benet/be.h @@ -259,6 +259,8 @@ struct be_adapter { u32 port_num; bool promiscuous; u32 cap; + u32 rx_fc; /* Rx flow control */ + u32 tx_fc; /* Tx flow control */ }; extern const struct ethtool_ops be_ethtool_ops; diff --git a/drivers/net/benet/be_ethtool.c b/drivers/net/benet/be_ethtool.c index cda5bf2fc50..f0fd95b43c0 100644 --- a/drivers/net/benet/be_ethtool.c +++ b/drivers/net/benet/be_ethtool.c @@ -323,10 +323,12 @@ be_set_pauseparam(struct net_device *netdev, struct ethtool_pauseparam *ecmd) if (ecmd->autoneg != 0) return -EINVAL; + adapter->tx_fc = ecmd->tx_pause; + adapter->rx_fc = ecmd->rx_pause; - status = be_cmd_set_flow_control(adapter, ecmd->tx_pause, - ecmd->rx_pause); - if (!status) + status = be_cmd_set_flow_control(adapter, + adapter->tx_fc, adapter->rx_fc); + if (status) dev_warn(&adapter->pdev->dev, "Pause param set failed.\n"); return status; diff --git a/drivers/net/benet/be_main.c b/drivers/net/benet/be_main.c index 1f941f02771..4a7a4527182 100644 --- a/drivers/net/benet/be_main.c +++ b/drivers/net/benet/be_main.c @@ -1652,7 +1652,8 @@ static int be_setup(struct be_adapter *adapter) if (status != 0) goto mccqs_destroy; - status = be_cmd_set_flow_control(adapter, true, true); + status = be_cmd_set_flow_control(adapter, + adapter->tx_fc, adapter->rx_fc); if (status != 0) goto mccqs_destroy; return 0; @@ -1909,6 +1910,10 @@ static void be_netdev_init(struct net_device *netdev) adapter->rx_csum = true; + /* Default settings for Rx and Tx flow control */ + adapter->rx_fc = true; + adapter->tx_fc = true; + netif_set_gso_max_size(netdev, 65535); BE_SET_NETDEV_OPS(netdev, &be_netdev_ops); @@ -2171,6 +2176,7 @@ static int be_suspend(struct pci_dev *pdev, pm_message_t state) be_close(netdev); rtnl_unlock(); } + be_cmd_get_flow_control(adapter, &adapter->tx_fc, &adapter->rx_fc); be_clear(adapter); pci_save_state(pdev); -- cgit v1.2.3 From 4f2aa89cd263932d61f286307771996df76bf63e Mon Sep 17 00:00:00 2001 From: Ajit Khaparde Date: Fri, 6 Nov 2009 02:07:32 +0000 Subject: be2net: Bug fix to send config commands to hardware after netdev_register Sending config commands to be2 hardware before netdev_register is completed, is sometimes causing the async link notification to arrive even before the driver is ready to handle it. The commands for vlan config and flow control settings can infact wait till be_open. This patch takes care of that. Signed-off-by: Ajit Khaparde Signed-off-by: David S. Miller --- drivers/net/benet/be_main.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) diff --git a/drivers/net/benet/be_main.c b/drivers/net/benet/be_main.c index 4a7a4527182..876b357101f 100644 --- a/drivers/net/benet/be_main.c +++ b/drivers/net/benet/be_main.c @@ -1610,11 +1610,21 @@ static int be_open(struct net_device *netdev) status = be_cmd_link_status_query(adapter, &link_up); if (status) - return status; + goto ret_sts; be_link_status_update(adapter, link_up); + status = be_vid_config(adapter); + if (status) + goto ret_sts; + + status = be_cmd_set_flow_control(adapter, + adapter->tx_fc, adapter->rx_fc); + if (status) + goto ret_sts; + schedule_delayed_work(&adapter->work, msecs_to_jiffies(100)); - return 0; +ret_sts: + return status; } static int be_setup(struct be_adapter *adapter) @@ -1648,18 +1658,8 @@ static int be_setup(struct be_adapter *adapter) if (status != 0) goto rx_qs_destroy; - status = be_vid_config(adapter); - if (status != 0) - goto mccqs_destroy; - - status = be_cmd_set_flow_control(adapter, - adapter->tx_fc, adapter->rx_fc); - if (status != 0) - goto mccqs_destroy; return 0; -mccqs_destroy: - be_mcc_queues_destroy(adapter); rx_qs_destroy: be_rx_queues_destroy(adapter); tx_qs_destroy: -- cgit v1.2.3 From 2b2072e902848a63168570f500a5726744b3873a Mon Sep 17 00:00:00 2001 From: Sebastian Haas Date: Wed, 4 Nov 2009 05:48:33 +0000 Subject: ems_usb: Fix byte order issues on big endian machines CPC-USB is using a ARM7 core with little endian byte order. The "id" field in can_msg needs byte order conversion from/to CPU byte order. Signed-off-by: Sebastian Haas Signed-off-by: David S. Miller --- drivers/net/can/usb/ems_usb.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/net/can/usb/ems_usb.c b/drivers/net/can/usb/ems_usb.c index 9012e0abc62..abdbd9c2b78 100644 --- a/drivers/net/can/usb/ems_usb.c +++ b/drivers/net/can/usb/ems_usb.c @@ -319,7 +319,7 @@ static void ems_usb_rx_can_msg(struct ems_usb *dev, struct ems_cpc_msg *msg) cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame)); - cf->can_id = msg->msg.can_msg.id; + cf->can_id = le32_to_cpu(msg->msg.can_msg.id); cf->can_dlc = min_t(u8, msg->msg.can_msg.length, 8); if (msg->type == CPC_MSG_TYPE_EXT_CAN_FRAME @@ -813,6 +813,9 @@ static netdev_tx_t ems_usb_start_xmit(struct sk_buff *skb, struct net_device *ne msg->length = CPC_CAN_MSG_MIN_SIZE + cf->can_dlc; } + /* Respect byte order */ + msg->msg.can_msg.id = cpu_to_le32(msg->msg.can_msg.id); + for (i = 0; i < MAX_TX_URBS; i++) { if (dev->tx_contexts[i].echo_index == MAX_TX_URBS) { context = &dev->tx_contexts[i]; -- cgit v1.2.3 From 87d75b52414a22c54cf8382bcdd329376b1bce78 Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Thu, 5 Nov 2009 23:14:29 +0000 Subject: NET: cassini, fix lock imbalance Stanse found that one error path in cas_open omits to unlock pm_mutex. Fix that. Signed-off-by: Jiri Slaby Signed-off-by: David S. Miller --- drivers/net/cassini.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/net/cassini.c b/drivers/net/cassini.c index 05916aafa4f..f857afe8e48 100644 --- a/drivers/net/cassini.c +++ b/drivers/net/cassini.c @@ -4342,11 +4342,11 @@ static int cas_open(struct net_device *dev) cas_unlock_all_restore(cp, flags); } + err = -ENOMEM; if (cas_tx_tiny_alloc(cp) < 0) - return -ENOMEM; + goto err_unlock; /* alloc rx descriptors */ - err = -ENOMEM; if (cas_alloc_rxds(cp) < 0) goto err_tx_tiny; @@ -4386,6 +4386,7 @@ err_spare: cas_free_rxds(cp); err_tx_tiny: cas_tx_tiny_free(cp); +err_unlock: mutex_unlock(&cp->pm_mutex); return err; } -- cgit v1.2.3 From dcaa6a9414cdc767c0afba4705c25ae9cf6096b5 Mon Sep 17 00:00:00 2001 From: Finn Thain Date: Tue, 3 Nov 2009 03:42:40 +0000 Subject: macsonic: fix crash on PowerBook 520 No-one seems to know where the PowerBook 500 series store their ethernet MAC addresses. So, rather than crash, use a MAC address from the SONIC CAM. Failing that, generate a random one. Signed-off-by: Finn Thain Signed-off-by: David S. Miller --- drivers/net/macsonic.c | 117 +++++++++++++++++++++++++------------------------ 1 file changed, 60 insertions(+), 57 deletions(-) diff --git a/drivers/net/macsonic.c b/drivers/net/macsonic.c index 61eabcac734..b3d7d8d77f4 100644 --- a/drivers/net/macsonic.c +++ b/drivers/net/macsonic.c @@ -223,69 +223,73 @@ static int __devinit macsonic_init(struct net_device *dev) return 0; } -static int __devinit mac_onboard_sonic_ethernet_addr(struct net_device *dev) +#define INVALID_MAC(mac) (memcmp(mac, "\x08\x00\x07", 3) && \ + memcmp(mac, "\x00\xA0\x40", 3) && \ + memcmp(mac, "\x00\x80\x19", 3) && \ + memcmp(mac, "\x00\x05\x02", 3)) + +static void __devinit mac_onboard_sonic_ethernet_addr(struct net_device *dev) { struct sonic_local *lp = netdev_priv(dev); const int prom_addr = ONBOARD_SONIC_PROM_BASE; - int i; + unsigned short val; - /* On NuBus boards we can sometimes look in the ROM resources. - No such luck for comm-slot/onboard. */ - for(i = 0; i < 6; i++) - dev->dev_addr[i] = SONIC_READ_PROM(i); + /* + * On NuBus boards we can sometimes look in the ROM resources. + * No such luck for comm-slot/onboard. + * On the PowerBook 520, the PROM base address is a mystery. + */ + if (hwreg_present((void *)prom_addr)) { + int i; + + for (i = 0; i < 6; i++) + dev->dev_addr[i] = SONIC_READ_PROM(i); + if (!INVALID_MAC(dev->dev_addr)) + return; - /* Most of the time, the address is bit-reversed. The NetBSD - source has a rather long and detailed historical account of - why this is so. */ - if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) && - memcmp(dev->dev_addr, "\x00\xA0\x40", 3) && - memcmp(dev->dev_addr, "\x00\x80\x19", 3) && - memcmp(dev->dev_addr, "\x00\x05\x02", 3)) + /* + * Most of the time, the address is bit-reversed. The NetBSD + * source has a rather long and detailed historical account of + * why this is so. + */ bit_reverse_addr(dev->dev_addr); - else - return 0; - - /* If we still have what seems to be a bogus address, we'll - look in the CAM. The top entry should be ours. */ - /* Danger! This only works if MacOS has already initialized - the card... */ - if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) && - memcmp(dev->dev_addr, "\x00\xA0\x40", 3) && - memcmp(dev->dev_addr, "\x00\x80\x19", 3) && - memcmp(dev->dev_addr, "\x00\x05\x02", 3)) - { - unsigned short val; - - printk(KERN_INFO "macsonic: PROM seems to be wrong, trying CAM entry 15\n"); - - SONIC_WRITE(SONIC_CMD, SONIC_CR_RST); - SONIC_WRITE(SONIC_CEP, 15); - - val = SONIC_READ(SONIC_CAP2); - dev->dev_addr[5] = val >> 8; - dev->dev_addr[4] = val & 0xff; - val = SONIC_READ(SONIC_CAP1); - dev->dev_addr[3] = val >> 8; - dev->dev_addr[2] = val & 0xff; - val = SONIC_READ(SONIC_CAP0); - dev->dev_addr[1] = val >> 8; - dev->dev_addr[0] = val & 0xff; - - printk(KERN_INFO "HW Address from CAM 15: %pM\n", - dev->dev_addr); - } else return 0; - - if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) && - memcmp(dev->dev_addr, "\x00\xA0\x40", 3) && - memcmp(dev->dev_addr, "\x00\x80\x19", 3) && - memcmp(dev->dev_addr, "\x00\x05\x02", 3)) - { + if (!INVALID_MAC(dev->dev_addr)) + return; + /* - * Still nonsense ... messed up someplace! + * If we still have what seems to be a bogus address, we'll + * look in the CAM. The top entry should be ours. */ - printk(KERN_ERR "macsonic: ERROR (INVALID MAC)\n"); - return -EIO; - } else return 0; + printk(KERN_WARNING "macsonic: MAC address in PROM seems " + "to be invalid, trying CAM\n"); + } else { + printk(KERN_WARNING "macsonic: cannot read MAC address from " + "PROM, trying CAM\n"); + } + + /* This only works if MacOS has already initialized the card. */ + + SONIC_WRITE(SONIC_CMD, SONIC_CR_RST); + SONIC_WRITE(SONIC_CEP, 15); + + val = SONIC_READ(SONIC_CAP2); + dev->dev_addr[5] = val >> 8; + dev->dev_addr[4] = val & 0xff; + val = SONIC_READ(SONIC_CAP1); + dev->dev_addr[3] = val >> 8; + dev->dev_addr[2] = val & 0xff; + val = SONIC_READ(SONIC_CAP0); + dev->dev_addr[1] = val >> 8; + dev->dev_addr[0] = val & 0xff; + + if (!INVALID_MAC(dev->dev_addr)) + return; + + /* Still nonsense ... messed up someplace! */ + + printk(KERN_WARNING "macsonic: MAC address in CAM entry 15 " + "seems invalid, will use a random MAC\n"); + random_ether_addr(dev->dev_addr); } static int __devinit mac_onboard_sonic_probe(struct net_device *dev) @@ -402,8 +406,7 @@ static int __devinit mac_onboard_sonic_probe(struct net_device *dev) SONIC_WRITE(SONIC_ISR, 0x7fff); /* Now look for the MAC address. */ - if (mac_onboard_sonic_ethernet_addr(dev) != 0) - return -ENODEV; + mac_onboard_sonic_ethernet_addr(dev); /* Shared init code */ return macsonic_init(dev); -- cgit v1.2.3 From b352e40da8977253f49850a24f6448653a459ac0 Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Fri, 6 Nov 2009 12:55:38 +0000 Subject: ixgbe: Fix gso_max_size for 82599 when DCB is enabled The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599. Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index cbb143ca1eb..26fc1df2b2e 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -2471,7 +2471,10 @@ static void ixgbe_configure(struct ixgbe_adapter *adapter) ixgbe_restore_vlan(adapter); #ifdef CONFIG_IXGBE_DCB if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { - netif_set_gso_max_size(netdev, 32768); + if (hw->mac.type == ixgbe_mac_82598EB) + netif_set_gso_max_size(netdev, 32768); + else + netif_set_gso_max_size(netdev, 65536); ixgbe_configure_dcb(adapter); } else { netif_set_gso_max_size(netdev, 65536); -- cgit v1.2.3 From 26f23d82dd8eae6dcc2ab99c04a9256089576a73 Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Fri, 6 Nov 2009 12:56:00 +0000 Subject: ixgbe: Fix checking TFCS register for TXOFF status when DCB is enabled When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a function to map from the tx_ring hw reg_idx to the correspodning TC and read TFCS accordingly. Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 52 +++++++++++++++++++++++++++++++++++++++++- 1 file changed, 51 insertions(+), 1 deletion(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 26fc1df2b2e..2d0f618b4a9 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -226,6 +226,56 @@ static void ixgbe_unmap_and_free_tx_resource(struct ixgbe_adapter *adapter, /* tx_buffer_info must be completely set up in the transmit path */ } +/** + * ixgbe_tx_is_paused - check if the tx ring is paused + * @adapter: the ixgbe adapter + * @tx_ring: the corresponding tx_ring + * + * If not in DCB mode, checks TFCS.TXOFF, otherwise, find out the + * corresponding TC of this tx_ring when checking TFCS. + * + * Returns : true if paused + */ +static inline bool ixgbe_tx_is_paused(struct ixgbe_adapter *adapter, + struct ixgbe_ring *tx_ring) +{ + int tc; + u32 txoff = IXGBE_TFCS_TXOFF; + +#ifdef CONFIG_IXGBE_DCB + if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { + int reg_idx = tx_ring->reg_idx; + int dcb_i = adapter->ring_feature[RING_F_DCB].indices; + + if (adapter->hw.mac.type == ixgbe_mac_82598EB) { + tc = reg_idx >> 2; + txoff = IXGBE_TFCS_TXOFF0; + } else if (adapter->hw.mac.type == ixgbe_mac_82599EB) { + tc = 0; + txoff = IXGBE_TFCS_TXOFF; + if (dcb_i == 8) { + /* TC0, TC1 */ + tc = reg_idx >> 5; + if (tc == 2) /* TC2, TC3 */ + tc += (reg_idx - 64) >> 4; + else if (tc == 3) /* TC4, TC5, TC6, TC7 */ + tc += 1 + ((reg_idx - 96) >> 3); + } else if (dcb_i == 4) { + /* TC0, TC1 */ + tc = reg_idx >> 6; + if (tc == 1) { + tc += (reg_idx - 64) >> 5; + if (tc == 2) /* TC2, TC3 */ + tc += (reg_idx - 96) >> 4; + } + } + } + txoff <<= tc; + } +#endif + return IXGBE_READ_REG(&adapter->hw, IXGBE_TFCS) & txoff; +} + static inline bool ixgbe_check_tx_hang(struct ixgbe_adapter *adapter, struct ixgbe_ring *tx_ring, unsigned int eop) @@ -237,7 +287,7 @@ static inline bool ixgbe_check_tx_hang(struct ixgbe_adapter *adapter, adapter->detect_tx_hung = false; if (tx_ring->tx_buffer_info[eop].time_stamp && time_after(jiffies, tx_ring->tx_buffer_info[eop].time_stamp + HZ) && - !(IXGBE_READ_REG(&adapter->hw, IXGBE_TFCS) & IXGBE_TFCS_TXOFF)) { + !ixgbe_tx_is_paused(adapter, tx_ring)) { /* detected Tx unit hang */ union ixgbe_adv_tx_desc *tx_desc; tx_desc = IXGBE_TX_DESC_ADV(*tx_ring, eop); -- cgit v1.2.3 From ee5f784a2d48cdacf561e99b2d01b23364189474 Mon Sep 17 00:00:00 2001 From: Don Skidmore Date: Fri, 6 Nov 2009 12:56:20 +0000 Subject: ixgbe: fix traffic hangs on Tx with ioatdma loaded When ioatdma was loaded we we were unable to transmit traffic. We weren't using the correct registers in ixgbe_update_tx_dca for 82599 systems. Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before modifying MTQC. Signed-off-by: Don Skidmore Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 27 +++++++++++++++++++++++---- 1 file changed, 23 insertions(+), 4 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 2d0f618b4a9..5bd9e6bf6f2 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -44,6 +44,7 @@ #include "ixgbe.h" #include "ixgbe_common.h" +#include "ixgbe_dcb_82599.h" char ixgbe_driver_name[] = "ixgbe"; static const char ixgbe_driver_string[] = @@ -462,19 +463,23 @@ static void ixgbe_update_tx_dca(struct ixgbe_adapter *adapter, u32 txctrl; int cpu = get_cpu(); int q = tx_ring - adapter->tx_ring; + struct ixgbe_hw *hw = &adapter->hw; if (tx_ring->cpu != cpu) { - txctrl = IXGBE_READ_REG(&adapter->hw, IXGBE_DCA_TXCTRL(q)); if (adapter->hw.mac.type == ixgbe_mac_82598EB) { + txctrl = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL(q)); txctrl &= ~IXGBE_DCA_TXCTRL_CPUID_MASK; txctrl |= dca3_get_tag(&adapter->pdev->dev, cpu); + txctrl |= IXGBE_DCA_TXCTRL_DESC_DCA_EN; + IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL(q), txctrl); } else if (adapter->hw.mac.type == ixgbe_mac_82599EB) { + txctrl = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL_82599(q)); txctrl &= ~IXGBE_DCA_TXCTRL_CPUID_MASK_82599; txctrl |= (dca3_get_tag(&adapter->pdev->dev, cpu) << - IXGBE_DCA_TXCTRL_CPUID_SHIFT_82599); + IXGBE_DCA_TXCTRL_CPUID_SHIFT_82599); + txctrl |= IXGBE_DCA_TXCTRL_DESC_DCA_EN; + IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL_82599(q), txctrl); } - txctrl |= IXGBE_DCA_TXCTRL_DESC_DCA_EN; - IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_TXCTRL(q), txctrl); tx_ring->cpu = cpu; } put_cpu(); @@ -1963,11 +1968,25 @@ static void ixgbe_configure_tx(struct ixgbe_adapter *adapter) break; } } + if (hw->mac.type == ixgbe_mac_82599EB) { + u32 rttdcs; + + /* disable the arbiter while setting MTQC */ + rttdcs = IXGBE_READ_REG(hw, IXGBE_RTTDCS); + rttdcs |= IXGBE_RTTDCS_ARBDIS; + IXGBE_WRITE_REG(hw, IXGBE_RTTDCS, rttdcs); + /* We enable 8 traffic classes, DCB only */ if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) IXGBE_WRITE_REG(hw, IXGBE_MTQC, (IXGBE_MTQC_RT_ENA | IXGBE_MTQC_8TC_8TQ)); + else + IXGBE_WRITE_REG(hw, IXGBE_MTQC, IXGBE_MTQC_64Q_1PB); + + /* re-eable the arbiter */ + rttdcs &= ~IXGBE_RTTDCS_ARBDIS; + IXGBE_WRITE_REG(hw, IXGBE_RTTDCS, rttdcs); } } -- cgit v1.2.3 From 60fa6c374e7efcbed04bc6d11d3b35645c523b2f Mon Sep 17 00:00:00 2001 From: Ron Mercer Date: Fri, 6 Nov 2009 07:44:57 +0000 Subject: qlge: Fix early exit from mbox cmd complete wait. This line was accidentally left out of the previous commit # da03945140a035a2962f7f93e359085596f20499 ("qlge: Fix firmware mailbox command timeout."). Signed-off-by: Ron Mercer Signed-off-by: David S. Miller --- drivers/net/qlge/qlge_mpi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/qlge/qlge_mpi.c b/drivers/net/qlge/qlge_mpi.c index bcf13c96f73..aec05f26610 100644 --- a/drivers/net/qlge/qlge_mpi.c +++ b/drivers/net/qlge/qlge_mpi.c @@ -499,7 +499,7 @@ static int ql_mailbox_command(struct ql_adapter *qdev, struct mbox_params *mbcp) /* Wait for the interrupt to come in. */ status = ql_wait_mbx_cmd_cmplt(qdev); if (status) - goto end; + continue; /* Process the event. If it's an AEN, it * will be handled in-line or a worker -- cgit v1.2.3 From 73475339005dc68eb0bd2f6b1e93a3a39b628410 Mon Sep 17 00:00:00 2001 From: Ron Mercer Date: Fri, 6 Nov 2009 07:44:58 +0000 Subject: qlge: Set PCIe reset type for EEH to fundamental. This device requires a fundamental reset when recovering from EEH. Signed-off-by: Ron Mercer Signed-off-by: David S. Miller --- drivers/net/qlge/qlge_main.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/net/qlge/qlge_main.c b/drivers/net/qlge/qlge_main.c index cea7531f4f4..a2fc70a0d0c 100644 --- a/drivers/net/qlge/qlge_main.c +++ b/drivers/net/qlge/qlge_main.c @@ -3916,6 +3916,8 @@ static int __devinit ql_init_device(struct pci_dev *pdev, goto err_out; } + /* Set PCIe reset type for EEH to fundamental. */ + pdev->needs_freset = 1; pci_save_state(pdev); qdev->reg_base = ioremap_nocache(pci_resource_start(pdev, 1), -- cgit v1.2.3 From 23ca0c989e46924393f1d54bec84801d035dd28e Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Fri, 6 Nov 2009 10:37:41 +0000 Subject: ipip: Fix handling of DF packets when pmtudisc is OFF RFC 2003 requires the outer header to have DF set if DF is set on the inner header, even when PMTU discovery is off for the tunnel. Our implementation does exactly that. For this to work properly the IPIP gateway also needs to engate in PMTU when the inner DF bit is set. As otherwise the original host would not be able to carry out its PMTU successfully since part of the path is only visible to the gateway. Unfortunately when the tunnel PMTU discovery setting is off, we do not collect the necessary soft state, resulting in blackholes when the original host tries to perform PMTU discovery. This problem is not reproducible on the IPIP gateway itself as the inner packet usually has skb->local_df set. This is not correctly cleared (an unrelated bug) when the packet passes through the tunnel, which allows fragmentation to occur. For hosts behind the IPIP gateway it is readily visible with a simple ping. This patch fixes the problem by performing PMTU discovery for all packets with the inner DF bit set, regardless of the PMTU discovery setting on the tunnel itself. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- net/ipv4/ipip.c | 32 +++++++++++++++++--------------- 1 file changed, 17 insertions(+), 15 deletions(-) diff --git a/net/ipv4/ipip.c b/net/ipv4/ipip.c index 08ccd344de7..ae40ed1ba56 100644 --- a/net/ipv4/ipip.c +++ b/net/ipv4/ipip.c @@ -438,25 +438,27 @@ static netdev_tx_t ipip_tunnel_xmit(struct sk_buff *skb, struct net_device *dev) goto tx_error; } - if (tiph->frag_off) + df |= old_iph->frag_off & htons(IP_DF); + + if (df) { mtu = dst_mtu(&rt->u.dst) - sizeof(struct iphdr); - else - mtu = skb_dst(skb) ? dst_mtu(skb_dst(skb)) : dev->mtu; - if (mtu < 68) { - stats->collisions++; - ip_rt_put(rt); - goto tx_error; - } - if (skb_dst(skb)) - skb_dst(skb)->ops->update_pmtu(skb_dst(skb), mtu); + if (mtu < 68) { + stats->collisions++; + ip_rt_put(rt); + goto tx_error; + } - df |= (old_iph->frag_off&htons(IP_DF)); + if (skb_dst(skb)) + skb_dst(skb)->ops->update_pmtu(skb_dst(skb), mtu); - if ((old_iph->frag_off&htons(IP_DF)) && mtu < ntohs(old_iph->tot_len)) { - icmp_send(skb, ICMP_DEST_UNREACH, ICMP_FRAG_NEEDED, htonl(mtu)); - ip_rt_put(rt); - goto tx_error; + if ((old_iph->frag_off & htons(IP_DF)) && + mtu < ntohs(old_iph->tot_len)) { + icmp_send(skb, ICMP_DEST_UNREACH, ICMP_FRAG_NEEDED, + htonl(mtu)); + ip_rt_put(rt); + goto tx_error; + } } if (tunnel->err_count > 0) { -- cgit v1.2.3 From cc05368c52fed7d9efa0f56c5270e95bb569713e Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Fri, 6 Nov 2009 14:52:34 +0000 Subject: hisax: remove bad udelay call to fix build error on ARM The hisax ISDN driver fails to build on ARM with CONFIG_HISAX_ELSA: | drivers/built-in.o: In function `modem_set_dial': | drivers/isdn/hisax/elsa_ser.c:535: undefined reference to `__bad_udelay' | drivers/isdn/hisax/elsa_ser.c:544: undefined reference to `__bad_udelay' | drivers/built-in.o: In function `modem_set_init': | drivers/isdn/hisax/elsa_ser.c:486: undefined reference to `__bad_udelay' | [...] According to the comment in arch/arm/include/asm/delay.h, __bad_udelay is specifically designed on ARM to produce a build failure when udelay is called with a value > 2000. Signed-off-by: Martin Michlmayr Signed-off-by: David S. Miller --- drivers/isdn/hisax/elsa_ser.c | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-) diff --git a/drivers/isdn/hisax/elsa_ser.c b/drivers/isdn/hisax/elsa_ser.c index f181db46439..1657bba7879 100644 --- a/drivers/isdn/hisax/elsa_ser.c +++ b/drivers/isdn/hisax/elsa_ser.c @@ -477,62 +477,62 @@ static void modem_set_init(struct IsdnCardState *cs) { int timeout; -#define RCV_DELAY 20000 +#define RCV_DELAY 20 modem_write_cmd(cs, MInit_1, strlen(MInit_1)); timeout = 1000; while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY); + mdelay(RCV_DELAY); modem_write_cmd(cs, MInit_2, strlen(MInit_2)); timeout = 1000; while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY); + mdelay(RCV_DELAY); modem_write_cmd(cs, MInit_3, strlen(MInit_3)); timeout = 1000; while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY); + mdelay(RCV_DELAY); modem_write_cmd(cs, MInit_4, strlen(MInit_4)); timeout = 1000; while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY ); + mdelay(RCV_DELAY); modem_write_cmd(cs, MInit_5, strlen(MInit_5)); timeout = 1000; while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY); + mdelay(RCV_DELAY); modem_write_cmd(cs, MInit_6, strlen(MInit_6)); timeout = 1000; while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY); + mdelay(RCV_DELAY); modem_write_cmd(cs, MInit_7, strlen(MInit_7)); timeout = 1000; while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY); + mdelay(RCV_DELAY); } static void modem_set_dial(struct IsdnCardState *cs, int outgoing) { int timeout; -#define RCV_DELAY 20000 +#define RCV_DELAY 20 modem_write_cmd(cs, MInit_speed28800, strlen(MInit_speed28800)); timeout = 1000; while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY); + mdelay(RCV_DELAY); if (outgoing) modem_write_cmd(cs, MInit_dialout, strlen(MInit_dialout)); else @@ -541,7 +541,7 @@ modem_set_dial(struct IsdnCardState *cs, int outgoing) { while(timeout-- && cs->hw.elsa.transcnt) udelay(1000); debugl1(cs, "msi tout=%d", timeout); - udelay(RCV_DELAY); + mdelay(RCV_DELAY); } static void -- cgit v1.2.3 From 6755aebaaf9fc5416acfd4578ab7a1e122ecbc74 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 6 Nov 2009 00:23:01 +0000 Subject: can: should not use __dev_get_by_index() without locks bcm_proc_getifname() is called with RTNL and dev_base_lock not held. It calls __dev_get_by_index() without locks, and this is illegal (might crash) Close the race by holding dev_base_lock and copying dev->name in the protected section. Signed-off-by: Eric Dumazet Signed-off-by: Oliver Hartkopp Signed-off-by: David S. Miller --- net/can/bcm.c | 19 ++++++++++++------- 1 file changed, 12 insertions(+), 7 deletions(-) diff --git a/net/can/bcm.c b/net/can/bcm.c index 597da4f8f88..e8d58f33fe0 100644 --- a/net/can/bcm.c +++ b/net/can/bcm.c @@ -132,23 +132,27 @@ static inline struct bcm_sock *bcm_sk(const struct sock *sk) /* * procfs functions */ -static char *bcm_proc_getifname(int ifindex) +static char *bcm_proc_getifname(char *result, int ifindex) { struct net_device *dev; if (!ifindex) return "any"; - /* no usage counting */ + read_lock(&dev_base_lock); dev = __dev_get_by_index(&init_net, ifindex); if (dev) - return dev->name; + strcpy(result, dev->name); + else + strcpy(result, "???"); + read_unlock(&dev_base_lock); - return "???"; + return result; } static int bcm_proc_show(struct seq_file *m, void *v) { + char ifname[IFNAMSIZ]; struct sock *sk = (struct sock *)m->private; struct bcm_sock *bo = bcm_sk(sk); struct bcm_op *op; @@ -157,7 +161,7 @@ static int bcm_proc_show(struct seq_file *m, void *v) seq_printf(m, " / sk %p", sk); seq_printf(m, " / bo %p", bo); seq_printf(m, " / dropped %lu", bo->dropped_usr_msgs); - seq_printf(m, " / bound %s", bcm_proc_getifname(bo->ifindex)); + seq_printf(m, " / bound %s", bcm_proc_getifname(ifname, bo->ifindex)); seq_printf(m, " <<<\n"); list_for_each_entry(op, &bo->rx_ops, list) { @@ -169,7 +173,7 @@ static int bcm_proc_show(struct seq_file *m, void *v) continue; seq_printf(m, "rx_op: %03X %-5s ", - op->can_id, bcm_proc_getifname(op->ifindex)); + op->can_id, bcm_proc_getifname(ifname, op->ifindex)); seq_printf(m, "[%d]%c ", op->nframes, (op->flags & RX_CHECK_DLC)?'d':' '); if (op->kt_ival1.tv64) @@ -194,7 +198,8 @@ static int bcm_proc_show(struct seq_file *m, void *v) list_for_each_entry(op, &bo->tx_ops, list) { seq_printf(m, "tx_op: %03X %s [%d] ", - op->can_id, bcm_proc_getifname(op->ifindex), + op->can_id, + bcm_proc_getifname(ifname, op->ifindex), op->nframes); if (op->kt_ival1.tv64) -- cgit v1.2.3 From 53a0ef866dc379e577794819d0b8ade5ba338e3a Mon Sep 17 00:00:00 2001 From: Wolfgang Grandegger Date: Fri, 6 Nov 2009 23:53:13 +0000 Subject: can: fix WARN_ON dump in net/core/rtnetlink.c:rtmsg_ifinfo() On older kernels, e.g. 2.6.27, a WARN_ON dump in rtmsg_ifinfo() is thrown when the CAN device is registered due to insufficient skb space, as reported by various users. This patch adds the rtnl_link_ops "get_size" to fix the problem. I think this patch is required for more recent kernels as well, even if no WARN_ON dumps are triggered. Maybe we also need "get_xstats_size" for the CAN xstats. Signed-off-by: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/dev.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c index f0b9a1e1db4..564e31c9fee 100644 --- a/drivers/net/can/dev.c +++ b/drivers/net/can/dev.c @@ -589,6 +589,22 @@ static int can_changelink(struct net_device *dev, return 0; } +static size_t can_get_size(const struct net_device *dev) +{ + struct can_priv *priv = netdev_priv(dev); + size_t size; + + size = nla_total_size(sizeof(u32)); /* IFLA_CAN_STATE */ + size += sizeof(struct can_ctrlmode); /* IFLA_CAN_CTRLMODE */ + size += nla_total_size(sizeof(u32)); /* IFLA_CAN_RESTART_MS */ + size += sizeof(struct can_bittiming); /* IFLA_CAN_BITTIMING */ + size += sizeof(struct can_clock); /* IFLA_CAN_CLOCK */ + if (priv->bittiming_const) /* IFLA_CAN_BITTIMING_CONST */ + size += sizeof(struct can_bittiming_const); + + return size; +} + static int can_fill_info(struct sk_buff *skb, const struct net_device *dev) { struct can_priv *priv = netdev_priv(dev); @@ -639,6 +655,7 @@ static struct rtnl_link_ops can_link_ops __read_mostly = { .setup = can_setup, .newlink = can_newlink, .changelink = can_changelink, + .get_size = can_get_size, .fill_info = can_fill_info, .fill_xstats = can_fill_xstats, }; -- cgit v1.2.3 From 2606289779cb297320a185db5997729d29b6700b Mon Sep 17 00:00:00 2001 From: Sebastian Siewior Date: Fri, 6 Nov 2009 08:50:28 +0000 Subject: net/fsl_pq_mdio: add module license GPL or it will taint the kernel and fail to load becuase of_address_to_resource() is GPL only. Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: David S. Miller --- drivers/net/fsl_pq_mdio.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/fsl_pq_mdio.c b/drivers/net/fsl_pq_mdio.c index 6ac46486697..efbf67689ec 100644 --- a/drivers/net/fsl_pq_mdio.c +++ b/drivers/net/fsl_pq_mdio.c @@ -427,3 +427,4 @@ void fsl_pq_mdio_exit(void) of_unregister_platform_driver(&fsl_pq_mdio_driver); } module_exit(fsl_pq_mdio_exit); +MODULE_LICENSE("GPL"); -- cgit v1.2.3