From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- drivers/cdrom/Kconfig | 213 ++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 213 insertions(+) create mode 100644 drivers/cdrom/Kconfig (limited to 'drivers/cdrom/Kconfig') diff --git a/drivers/cdrom/Kconfig b/drivers/cdrom/Kconfig new file mode 100644 index 00000000000..ff5652d4061 --- /dev/null +++ b/drivers/cdrom/Kconfig @@ -0,0 +1,213 @@ +# +# CDROM driver configuration +# + +menu "Old CD-ROM drivers (not SCSI, not IDE)" + depends on ISA + +config CD_NO_IDESCSI + bool "Support non-SCSI/IDE/ATAPI CDROM drives" + ---help--- + If you have a CD-ROM drive that is neither SCSI nor IDE/ATAPI, say Y + here, otherwise N. Read the CD-ROM-HOWTO, available from + . + + Note that the answer to this question doesn't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about these CD-ROM drives. If you are unsure what you + have, say Y and find out whether you have one of the following + drives. + + For each of these drivers, a + exists. Especially in cases where you do not know exactly which kind + of drive you have you should read there. Most of these drivers use a + file drivers/cdrom/{driver_name}.h where you can define your + interface parameters and switch some internal goodies. + + To compile these CD-ROM drivers as a module, choose M instead of Y. + + If you want to use any of these CD-ROM drivers, you also have to + answer Y or M to "ISO 9660 CD-ROM file system support" below (this + answer will get "defaulted" for you if you enable any of the Linux + CD-ROM drivers). + +config AZTCD + tristate "Aztech/Orchid/Okano/Wearnes/TXC/CyDROM CDROM support" + depends on CD_NO_IDESCSI + ---help--- + This is your driver if you have an Aztech CDA268-01A, Orchid + CD-3110, Okano or Wearnes CDD110, Conrad TXC, or CyCD-ROM CR520 or + CR540 CD-ROM drive. This driver -- just like all these CD-ROM + drivers -- is NOT for CD-ROM drives with IDE/ATAPI interfaces, such + as Aztech CDA269-031SE. Please read the file + . + + If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM + file system support" below, because that's the file system used on + CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called aztcd. + +config GSCD + tristate "Goldstar R420 CDROM support" + depends on CD_NO_IDESCSI + ---help--- + If this is your CD-ROM drive, say Y here. As described in the file + , you might have to change a setting + in the file before compiling the + kernel. Please read the file . + + If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM + file system support" below, because that's the file system used on + CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called gscd. + +config SBPCD + tristate "Matsushita/Panasonic/Creative, Longshine, TEAC CDROM support" + depends on CD_NO_IDESCSI && BROKEN_ON_SMP + ---help--- + This driver supports most of the drives which use the Panasonic or + Sound Blaster interface. Please read the file + . + + The Matsushita CR-521, CR-522, CR-523, CR-562, CR-563 drives + (sometimes labeled "Creative"), the Creative Labs CD200, the + Longshine LCS-7260, the "IBM External ISA CD-ROM" (in fact a CR-56x + model), the TEAC CD-55A fall under this category. Some other + "electrically compatible" drives (Vertos, Genoa, some Funai models) + are currently not supported; for the Sanyo H94A drive currently a + separate driver (asked later) is responsible. Most drives have a + uniquely shaped faceplate, with a caddyless motorized drawer, but + without external brand markings. The older CR-52x drives have a + caddy and manual loading/eject, but still no external markings. The + driver is able to do an extended auto-probing for interface + addresses and drive types; this can help to find facts in cases you + are not sure, but can consume some time during the boot process if + none of the supported drives gets found. Once your drive got found, + you should enter the reported parameters into + and set "DISTRIBUTION 0" there. + + This driver can support up to four CD-ROM controller cards, and each + card can support up to four CD-ROM drives; if you say Y here, you + will be asked how many controller cards you have. If compiled as a + module, only one controller card (but with up to four drives) is + usable. + + If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM + file system support" below, because that's the file system used on + CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called sbpcd. + +config MCDX + tristate "Mitsumi CDROM support" + depends on CD_NO_IDESCSI + ---help--- + Use this driver if you want to be able to use your Mitsumi LU-005, + FX-001 or FX-001D CD-ROM drive. + + Please read the file . + + If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM + file system support" below, because that's the file system used on + CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called mcdx. + +config OPTCD + tristate "Optics Storage DOLPHIN 8000AT CDROM support" + depends on CD_NO_IDESCSI + ---help--- + This is the driver for the 'DOLPHIN' drive with a 34-pin Sony + compatible interface. It also works with the Lasermate CR328A. If + you have one of those, say Y. This driver does not work for the + Optics Storage 8001 drive; use the IDE-ATAPI CD-ROM driver for that + one. Please read the file . + + If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM + file system support" below, because that's the file system used on + CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called optcd. + +config CM206 + tristate "Philips/LMS CM206 CDROM support" + depends on CD_NO_IDESCSI && BROKEN_ON_SMP + ---help--- + If you have a Philips/LMS CD-ROM drive cm206 in combination with a + cm260 host adapter card, say Y here. Please also read the file + . + + If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM + file system support" below, because that's the file system used on + CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called cm206. + +config SJCD + tristate "Sanyo CDR-H94A CDROM support" + depends on CD_NO_IDESCSI + help + If this is your CD-ROM drive, say Y here and read the file + . You should then also say Y or M to + "ISO 9660 CD-ROM file system support" below, because that's the + file system used on CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called sjcd. + +config ISP16_CDI + tristate "ISP16/MAD16/Mozart soft configurable cdrom interface support" + depends on CD_NO_IDESCSI + ---help--- + These are sound cards with built-in cdrom interfaces using the OPTi + 82C928 or 82C929 chips. Say Y here to have them detected and + possibly configured at boot time. In addition, You'll have to say Y + to a driver for the particular cdrom drive you have attached to the + card. Read for details. + + To compile this driver as a module, choose M here: the + module will be called isp16. + +config CDU31A + tristate "Sony CDU31A/CDU33A CDROM support" + depends on CD_NO_IDESCSI && BROKEN_ON_SMP + ---help--- + These CD-ROM drives have a spring-pop-out caddyless drawer, and a + rectangular green LED centered beneath it. NOTE: these CD-ROM + drives will not be auto detected by the kernel at boot time; you + have to provide the interface address as an option to the kernel at + boot time as described in or fill + in your parameters into . Try "man + bootparam" or see the documentation of your boot loader (lilo or + loadlin) about how to pass options to the kernel. + + If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM + file system support" below, because that's the file system used on + CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called cdu31a. + +config CDU535 + tristate "Sony CDU535 CDROM support" + depends on CD_NO_IDESCSI + ---help--- + This is the driver for the older Sony CDU-535 and CDU-531 CD-ROM + drives. Please read the file . + + If you say Y here, you should also say Y or M to "ISO 9660 CD-ROM + file system support" below, because that's the file system used on + CD-ROMs. + + To compile this driver as a module, choose M here: the + module will be called sonycd535. + +endmenu -- cgit v1.2.3