From 82466f00ec6ef0a5ca7ea8991c731af2ec561c7d Mon Sep 17 00:00:00 2001 From: Michael Albaugh Date: Wed, 16 May 2007 15:45:09 -0700 Subject: IB/ipath: Support blinking LEDs with an led_override file When we want to find an InfiniPath HCA in a rack of nodes, it is often expeditious to blink the status LEDs via a userspace /sys file. A write-only led_override "file" is published per device. Writes to this file are interpreted as (string form) numbers, and the resulting value sent to ipath_set_led_override(). The upper eight bits are interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom two 4-bit values are alternately (D0..3, then D4..7) used by the board-specific LED-setting function to override the normal state. Signed-off-by: Michael Albaugh Signed-off-by: Roland Dreier --- drivers/infiniband/hw/ipath/ipath_driver.c | 92 +++++++++++++++++++++++++++++- 1 file changed, 91 insertions(+), 1 deletion(-) (limited to 'drivers/infiniband/hw/ipath/ipath_driver.c') diff --git a/drivers/infiniband/hw/ipath/ipath_driver.c b/drivers/infiniband/hw/ipath/ipath_driver.c index e3a22320971..09759328658 100644 --- a/drivers/infiniband/hw/ipath/ipath_driver.c +++ b/drivers/infiniband/hw/ipath/ipath_driver.c @@ -1846,6 +1846,87 @@ void ipath_write_kreg_port(const struct ipath_devdata *dd, ipath_kreg regno, ipath_write_kreg(dd, where, value); } +/* + * Following deal with the "obviously simple" task of overriding the state + * of the LEDS, which normally indicate link physical and logical status. + * The complications arise in dealing with different hardware mappings + * and the board-dependent routine being called from interrupts. + * and then there's the requirement to _flash_ them. + */ +#define LED_OVER_FREQ_SHIFT 8 +#define LED_OVER_FREQ_MASK (0xFF<ipath_flags & IPATH_INITTED)) + return; + + pidx = dd->ipath_led_override_phase++ & 1; + dd->ipath_led_override = dd->ipath_led_override_vals[pidx]; + timeoff = dd->ipath_led_override_timeoff; + + /* + * below potentially restores the LED values per current status, + * should also possibly setup the traffic-blink register, + * but leave that to per-chip functions. + */ + val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcstatus); + ltstate = (val >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) & + INFINIPATH_IBCS_LINKTRAININGSTATE_MASK; + lstate = (val >> INFINIPATH_IBCS_LINKSTATE_SHIFT) & + INFINIPATH_IBCS_LINKSTATE_MASK; + + dd->ipath_f_setextled(dd, lstate, ltstate); + mod_timer(&dd->ipath_led_override_timer, jiffies + timeoff); +} + +void ipath_set_led_override(struct ipath_devdata *dd, unsigned int val) +{ + int timeoff, freq; + + if (!(dd->ipath_flags & IPATH_INITTED)) + return; + + /* First check if we are blinking. If not, use 1HZ polling */ + timeoff = HZ; + freq = (val & LED_OVER_FREQ_MASK) >> LED_OVER_FREQ_SHIFT; + + if (freq) { + /* For blink, set each phase from one nybble of val */ + dd->ipath_led_override_vals[0] = val & 0xF; + dd->ipath_led_override_vals[1] = (val >> 4) & 0xF; + timeoff = (HZ << 4)/freq; + } else { + /* Non-blink set both phases the same. */ + dd->ipath_led_override_vals[0] = val & 0xF; + dd->ipath_led_override_vals[1] = val & 0xF; + } + dd->ipath_led_override_timeoff = timeoff; + + /* + * If the timer has not already been started, do so. Use a "quick" + * timeout so the function will be called soon, to look at our request. + */ + if (atomic_inc_return(&dd->ipath_led_override_timer_active) == 1) { + /* Need to start timer */ + init_timer(&dd->ipath_led_override_timer); + dd->ipath_led_override_timer.function = + ipath_run_led_override; + dd->ipath_led_override_timer.data = (unsigned long) dd; + dd->ipath_led_override_timer.expires = jiffies + 1; + add_timer(&dd->ipath_led_override_timer); + } else { + atomic_dec(&dd->ipath_led_override_timer_active); + } +} + /** * ipath_shutdown_device - shut down a device * @dd: the infinipath device @@ -1909,7 +1990,6 @@ void ipath_shutdown_device(struct ipath_devdata *dd) * Turn the LEDs off explictly for the same reason. */ dd->ipath_f_quiet_serdes(dd); - dd->ipath_f_setextled(dd, 0, 0); if (dd->ipath_stats_timer_active) { del_timer_sync(&dd->ipath_stats_timer); @@ -2085,6 +2165,16 @@ int ipath_reset_device(int unit) goto bail; } + if (atomic_read(&dd->ipath_led_override_timer_active)) { + /* Need to stop LED timer, _then_ shut off LEDs */ + del_timer_sync(&dd->ipath_led_override_timer); + atomic_set(&dd->ipath_led_override_timer_active, 0); + } + + /* Shut off LEDs after we are sure timer is not running */ + dd->ipath_led_override = LED_OVER_BOTH_OFF; + dd->ipath_f_setextled(dd, 0, 0); + dev_info(&dd->pcidev->dev, "Reset on unit %u requested\n", unit); if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) { -- cgit v1.2.3