From fbd6a754f72a0a06e67544745b82c1d99b4c237d Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Fri, 19 Oct 2007 16:03:46 +0200 Subject: mv643xx_eth: Merge drivers/net/mv643xx_eth.h into mv643xx_eth.c Since drivers/net/mv643xx_eth.c is the only user of drivers/net/mv643xx_eth.h, there's not much use in having the header file as a separate file, so merge the header into the driver. Signed-off-by: Lennert Buytenhek Signed-off-by: Dale Farnsworth --- drivers/net/mv643xx_eth.c | 558 +++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 557 insertions(+), 1 deletion(-) (limited to 'drivers/net/mv643xx_eth.c') diff --git a/drivers/net/mv643xx_eth.c b/drivers/net/mv643xx_eth.c index ca120e53b58..b1980328ead 100644 --- a/drivers/net/mv643xx_eth.c +++ b/drivers/net/mv643xx_eth.c @@ -43,14 +43,570 @@ #include #include +#include +#include +#include +#include +#include + +#include + #include #include #include #include #include -#include "mv643xx_eth.h" +#include + +/* Checksum offload for Tx works for most packets, but + * fails if previous packet sent did not use hw csum + */ +#define MV643XX_CHECKSUM_OFFLOAD_TX +#define MV643XX_NAPI +#define MV643XX_TX_FAST_REFILL +#undef MV643XX_COAL + +/* + * Number of RX / TX descriptors on RX / TX rings. + * Note that allocating RX descriptors is done by allocating the RX + * ring AND a preallocated RX buffers (skb's) for each descriptor. + * The TX descriptors only allocates the TX descriptors ring, + * with no pre allocated TX buffers (skb's are allocated by higher layers. + */ + +/* Default TX ring size is 1000 descriptors */ +#define MV643XX_DEFAULT_TX_QUEUE_SIZE 1000 + +/* Default RX ring size is 400 descriptors */ +#define MV643XX_DEFAULT_RX_QUEUE_SIZE 400 + +#define MV643XX_TX_COAL 100 +#ifdef MV643XX_COAL +#define MV643XX_RX_COAL 100 +#endif + +#ifdef MV643XX_CHECKSUM_OFFLOAD_TX +#define MAX_DESCS_PER_SKB (MAX_SKB_FRAGS + 1) +#else +#define MAX_DESCS_PER_SKB 1 +#endif + +#define ETH_VLAN_HLEN 4 +#define ETH_FCS_LEN 4 +#define ETH_HW_IP_ALIGN 2 /* hw aligns IP header */ +#define ETH_WRAPPER_LEN (ETH_HW_IP_ALIGN + ETH_HLEN + \ + ETH_VLAN_HLEN + ETH_FCS_LEN) +#define ETH_RX_SKB_SIZE (dev->mtu + ETH_WRAPPER_LEN + \ + dma_get_cache_alignment()) + +/* + * Registers shared between all ports. + */ +#define PHY_ADDR_REG 0x0000 +#define SMI_REG 0x0004 + +/* + * Per-port registers. + */ +#define PORT_CONFIG_REG(p) (0x0400 + ((p) << 10)) +#define PORT_CONFIG_EXTEND_REG(p) (0x0404 + ((p) << 10)) +#define MAC_ADDR_LOW(p) (0x0414 + ((p) << 10)) +#define MAC_ADDR_HIGH(p) (0x0418 + ((p) << 10)) +#define SDMA_CONFIG_REG(p) (0x041c + ((p) << 10)) +#define PORT_SERIAL_CONTROL_REG(p) (0x043c + ((p) << 10)) +#define PORT_STATUS_REG(p) (0x0444 + ((p) << 10)) +#define TRANSMIT_QUEUE_COMMAND_REG(p) (0x0448 + ((p) << 10)) +#define MAXIMUM_TRANSMIT_UNIT(p) (0x0458 + ((p) << 10)) +#define INTERRUPT_CAUSE_REG(p) (0x0460 + ((p) << 10)) +#define INTERRUPT_CAUSE_EXTEND_REG(p) (0x0464 + ((p) << 10)) +#define INTERRUPT_MASK_REG(p) (0x0468 + ((p) << 10)) +#define INTERRUPT_EXTEND_MASK_REG(p) (0x046c + ((p) << 10)) +#define TX_FIFO_URGENT_THRESHOLD_REG(p) (0x0474 + ((p) << 10)) +#define RX_CURRENT_QUEUE_DESC_PTR_0(p) (0x060c + ((p) << 10)) +#define RECEIVE_QUEUE_COMMAND_REG(p) (0x0680 + ((p) << 10)) +#define TX_CURRENT_QUEUE_DESC_PTR_0(p) (0x06c0 + ((p) << 10)) +#define MIB_COUNTERS_BASE(p) (0x1000 + ((p) << 7)) +#define DA_FILTER_SPECIAL_MULTICAST_TABLE_BASE(p) (0x1400 + ((p) << 10)) +#define DA_FILTER_OTHER_MULTICAST_TABLE_BASE(p) (0x1500 + ((p) << 10)) +#define DA_FILTER_UNICAST_TABLE_BASE(p) (0x1600 + ((p) << 10)) + +/* These macros describe Ethernet Port configuration reg (Px_cR) bits */ +#define UNICAST_NORMAL_MODE (0 << 0) +#define UNICAST_PROMISCUOUS_MODE (1 << 0) +#define DEFAULT_RX_QUEUE(queue) ((queue) << 1) +#define DEFAULT_RX_ARP_QUEUE(queue) ((queue) << 4) +#define RECEIVE_BC_IF_NOT_IP_OR_ARP (0 << 7) +#define REJECT_BC_IF_NOT_IP_OR_ARP (1 << 7) +#define RECEIVE_BC_IF_IP (0 << 8) +#define REJECT_BC_IF_IP (1 << 8) +#define RECEIVE_BC_IF_ARP (0 << 9) +#define REJECT_BC_IF_ARP (1 << 9) +#define TX_AM_NO_UPDATE_ERROR_SUMMARY (1 << 12) +#define CAPTURE_TCP_FRAMES_DIS (0 << 14) +#define CAPTURE_TCP_FRAMES_EN (1 << 14) +#define CAPTURE_UDP_FRAMES_DIS (0 << 15) +#define CAPTURE_UDP_FRAMES_EN (1 << 15) +#define DEFAULT_RX_TCP_QUEUE(queue) ((queue) << 16) +#define DEFAULT_RX_UDP_QUEUE(queue) ((queue) << 19) +#define DEFAULT_RX_BPDU_QUEUE(queue) ((queue) << 22) + +#define PORT_CONFIG_DEFAULT_VALUE \ + UNICAST_NORMAL_MODE | \ + DEFAULT_RX_QUEUE(0) | \ + DEFAULT_RX_ARP_QUEUE(0) | \ + RECEIVE_BC_IF_NOT_IP_OR_ARP | \ + RECEIVE_BC_IF_IP | \ + RECEIVE_BC_IF_ARP | \ + CAPTURE_TCP_FRAMES_DIS | \ + CAPTURE_UDP_FRAMES_DIS | \ + DEFAULT_RX_TCP_QUEUE(0) | \ + DEFAULT_RX_UDP_QUEUE(0) | \ + DEFAULT_RX_BPDU_QUEUE(0) + +/* These macros describe Ethernet Port configuration extend reg (Px_cXR) bits*/ +#define CLASSIFY_EN (1 << 0) +#define SPAN_BPDU_PACKETS_AS_NORMAL (0 << 1) +#define SPAN_BPDU_PACKETS_TO_RX_QUEUE_7 (1 << 1) +#define PARTITION_DISABLE (0 << 2) +#define PARTITION_ENABLE (1 << 2) + +#define PORT_CONFIG_EXTEND_DEFAULT_VALUE \ + SPAN_BPDU_PACKETS_AS_NORMAL | \ + PARTITION_DISABLE + +/* These macros describe Ethernet Port Sdma configuration reg (SDCR) bits */ +#define RIFB (1 << 0) +#define RX_BURST_SIZE_1_64BIT (0 << 1) +#define RX_BURST_SIZE_2_64BIT (1 << 1) +#define RX_BURST_SIZE_4_64BIT (2 << 1) +#define RX_BURST_SIZE_8_64BIT (3 << 1) +#define RX_BURST_SIZE_16_64BIT (4 << 1) +#define BLM_RX_NO_SWAP (1 << 4) +#define BLM_RX_BYTE_SWAP (0 << 4) +#define BLM_TX_NO_SWAP (1 << 5) +#define BLM_TX_BYTE_SWAP (0 << 5) +#define DESCRIPTORS_BYTE_SWAP (1 << 6) +#define DESCRIPTORS_NO_SWAP (0 << 6) +#define IPG_INT_RX(value) (((value) & 0x3fff) << 8) +#define TX_BURST_SIZE_1_64BIT (0 << 22) +#define TX_BURST_SIZE_2_64BIT (1 << 22) +#define TX_BURST_SIZE_4_64BIT (2 << 22) +#define TX_BURST_SIZE_8_64BIT (3 << 22) +#define TX_BURST_SIZE_16_64BIT (4 << 22) + +#if defined(__BIG_ENDIAN) +#define PORT_SDMA_CONFIG_DEFAULT_VALUE \ + RX_BURST_SIZE_4_64BIT | \ + IPG_INT_RX(0) | \ + TX_BURST_SIZE_4_64BIT +#elif defined(__LITTLE_ENDIAN) +#define PORT_SDMA_CONFIG_DEFAULT_VALUE \ + RX_BURST_SIZE_4_64BIT | \ + BLM_RX_NO_SWAP | \ + BLM_TX_NO_SWAP | \ + IPG_INT_RX(0) | \ + TX_BURST_SIZE_4_64BIT +#else +#error One of __BIG_ENDIAN or __LITTLE_ENDIAN must be defined +#endif + +/* These macros describe Ethernet Port serial control reg (PSCR) bits */ +#define SERIAL_PORT_DISABLE (0 << 0) +#define SERIAL_PORT_ENABLE (1 << 0) +#define DO_NOT_FORCE_LINK_PASS (0 << 1) +#define FORCE_LINK_PASS (1 << 1) +#define ENABLE_AUTO_NEG_FOR_DUPLX (0 << 2) +#define DISABLE_AUTO_NEG_FOR_DUPLX (1 << 2) +#define ENABLE_AUTO_NEG_FOR_FLOW_CTRL (0 << 3) +#define DISABLE_AUTO_NEG_FOR_FLOW_CTRL (1 << 3) +#define ADV_NO_FLOW_CTRL (0 << 4) +#define ADV_SYMMETRIC_FLOW_CTRL (1 << 4) +#define FORCE_FC_MODE_NO_PAUSE_DIS_TX (0 << 5) +#define FORCE_FC_MODE_TX_PAUSE_DIS (1 << 5) +#define FORCE_BP_MODE_NO_JAM (0 << 7) +#define FORCE_BP_MODE_JAM_TX (1 << 7) +#define FORCE_BP_MODE_JAM_TX_ON_RX_ERR (2 << 7) +#define SERIAL_PORT_CONTROL_RESERVED (1 << 9) +#define FORCE_LINK_FAIL (0 << 10) +#define DO_NOT_FORCE_LINK_FAIL (1 << 10) +#define RETRANSMIT_16_ATTEMPTS (0 << 11) +#define RETRANSMIT_FOREVER (1 << 11) +#define ENABLE_AUTO_NEG_SPEED_GMII (0 << 13) +#define DISABLE_AUTO_NEG_SPEED_GMII (1 << 13) +#define DTE_ADV_0 (0 << 14) +#define DTE_ADV_1 (1 << 14) +#define DISABLE_AUTO_NEG_BYPASS (0 << 15) +#define ENABLE_AUTO_NEG_BYPASS (1 << 15) +#define AUTO_NEG_NO_CHANGE (0 << 16) +#define RESTART_AUTO_NEG (1 << 16) +#define MAX_RX_PACKET_1518BYTE (0 << 17) +#define MAX_RX_PACKET_1522BYTE (1 << 17) +#define MAX_RX_PACKET_1552BYTE (2 << 17) +#define MAX_RX_PACKET_9022BYTE (3 << 17) +#define MAX_RX_PACKET_9192BYTE (4 << 17) +#define MAX_RX_PACKET_9700BYTE (5 << 17) +#define MAX_RX_PACKET_MASK (7 << 17) +#define CLR_EXT_LOOPBACK (0 << 20) +#define SET_EXT_LOOPBACK (1 << 20) +#define SET_HALF_DUPLEX_MODE (0 << 21) +#define SET_FULL_DUPLEX_MODE (1 << 21) +#define DISABLE_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX (0 << 22) +#define ENABLE_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX (1 << 22) +#define SET_GMII_SPEED_TO_10_100 (0 << 23) +#define SET_GMII_SPEED_TO_1000 (1 << 23) +#define SET_MII_SPEED_TO_10 (0 << 24) +#define SET_MII_SPEED_TO_100 (1 << 24) + +#define PORT_SERIAL_CONTROL_DEFAULT_VALUE \ + DO_NOT_FORCE_LINK_PASS | \ + ENABLE_AUTO_NEG_FOR_DUPLX | \ + DISABLE_AUTO_NEG_FOR_FLOW_CTRL | \ + ADV_SYMMETRIC_FLOW_CTRL | \ + FORCE_FC_MODE_NO_PAUSE_DIS_TX | \ + FORCE_BP_MODE_NO_JAM | \ + (1 << 9) /* reserved */ | \ + DO_NOT_FORCE_LINK_FAIL | \ + RETRANSMIT_16_ATTEMPTS | \ + ENABLE_AUTO_NEG_SPEED_GMII | \ + DTE_ADV_0 | \ + DISABLE_AUTO_NEG_BYPASS | \ + AUTO_NEG_NO_CHANGE | \ + MAX_RX_PACKET_9700BYTE | \ + CLR_EXT_LOOPBACK | \ + SET_FULL_DUPLEX_MODE | \ + ENABLE_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX + +/* These macros describe Ethernet Serial Status reg (PSR) bits */ +#define PORT_STATUS_MODE_10_BIT (1 << 0) +#define PORT_STATUS_LINK_UP (1 << 1) +#define PORT_STATUS_FULL_DUPLEX (1 << 2) +#define PORT_STATUS_FLOW_CONTROL (1 << 3) +#define PORT_STATUS_GMII_1000 (1 << 4) +#define PORT_STATUS_MII_100 (1 << 5) +/* PSR bit 6 is undocumented */ +#define PORT_STATUS_TX_IN_PROGRESS (1 << 7) +#define PORT_STATUS_AUTONEG_BYPASSED (1 << 8) +#define PORT_STATUS_PARTITION (1 << 9) +#define PORT_STATUS_TX_FIFO_EMPTY (1 << 10) +/* PSR bits 11-31 are reserved */ + +#define PORT_DEFAULT_TRANSMIT_QUEUE_SIZE 800 +#define PORT_DEFAULT_RECEIVE_QUEUE_SIZE 400 + +#define DESC_SIZE 64 + +#define ETH_RX_QUEUES_ENABLED (1 << 0) /* use only Q0 for receive */ +#define ETH_TX_QUEUES_ENABLED (1 << 0) /* use only Q0 for transmit */ + +#define ETH_INT_CAUSE_RX_DONE (ETH_RX_QUEUES_ENABLED << 2) +#define ETH_INT_CAUSE_RX_ERROR (ETH_RX_QUEUES_ENABLED << 9) +#define ETH_INT_CAUSE_RX (ETH_INT_CAUSE_RX_DONE | ETH_INT_CAUSE_RX_ERROR) +#define ETH_INT_CAUSE_EXT 0x00000002 +#define ETH_INT_UNMASK_ALL (ETH_INT_CAUSE_RX | ETH_INT_CAUSE_EXT) + +#define ETH_INT_CAUSE_TX_DONE (ETH_TX_QUEUES_ENABLED << 0) +#define ETH_INT_CAUSE_TX_ERROR (ETH_TX_QUEUES_ENABLED << 8) +#define ETH_INT_CAUSE_TX (ETH_INT_CAUSE_TX_DONE | ETH_INT_CAUSE_TX_ERROR) +#define ETH_INT_CAUSE_PHY 0x00010000 +#define ETH_INT_CAUSE_STATE 0x00100000 +#define ETH_INT_UNMASK_ALL_EXT (ETH_INT_CAUSE_TX | ETH_INT_CAUSE_PHY | \ + ETH_INT_CAUSE_STATE) + +#define ETH_INT_MASK_ALL 0x00000000 +#define ETH_INT_MASK_ALL_EXT 0x00000000 + +#define PHY_WAIT_ITERATIONS 1000 /* 1000 iterations * 10uS = 10mS max */ +#define PHY_WAIT_MICRO_SECONDS 10 + +/* Buffer offset from buffer pointer */ +#define RX_BUF_OFFSET 0x2 + +/* Gigabit Ethernet Unit Global Registers */ + +/* MIB Counters register definitions */ +#define ETH_MIB_GOOD_OCTETS_RECEIVED_LOW 0x0 +#define ETH_MIB_GOOD_OCTETS_RECEIVED_HIGH 0x4 +#define ETH_MIB_BAD_OCTETS_RECEIVED 0x8 +#define ETH_MIB_INTERNAL_MAC_TRANSMIT_ERR 0xc +#define ETH_MIB_GOOD_FRAMES_RECEIVED 0x10 +#define ETH_MIB_BAD_FRAMES_RECEIVED 0x14 +#define ETH_MIB_BROADCAST_FRAMES_RECEIVED 0x18 +#define ETH_MIB_MULTICAST_FRAMES_RECEIVED 0x1c +#define ETH_MIB_FRAMES_64_OCTETS 0x20 +#define ETH_MIB_FRAMES_65_TO_127_OCTETS 0x24 +#define ETH_MIB_FRAMES_128_TO_255_OCTETS 0x28 +#define ETH_MIB_FRAMES_256_TO_511_OCTETS 0x2c +#define ETH_MIB_FRAMES_512_TO_1023_OCTETS 0x30 +#define ETH_MIB_FRAMES_1024_TO_MAX_OCTETS 0x34 +#define ETH_MIB_GOOD_OCTETS_SENT_LOW 0x38 +#define ETH_MIB_GOOD_OCTETS_SENT_HIGH 0x3c +#define ETH_MIB_GOOD_FRAMES_SENT 0x40 +#define ETH_MIB_EXCESSIVE_COLLISION 0x44 +#define ETH_MIB_MULTICAST_FRAMES_SENT 0x48 +#define ETH_MIB_BROADCAST_FRAMES_SENT 0x4c +#define ETH_MIB_UNREC_MAC_CONTROL_RECEIVED 0x50 +#define ETH_MIB_FC_SENT 0x54 +#define ETH_MIB_GOOD_FC_RECEIVED 0x58 +#define ETH_MIB_BAD_FC_RECEIVED 0x5c +#define ETH_MIB_UNDERSIZE_RECEIVED 0x60 +#define ETH_MIB_FRAGMENTS_RECEIVED 0x64 +#define ETH_MIB_OVERSIZE_RECEIVED 0x68 +#define ETH_MIB_JABBER_RECEIVED 0x6c +#define ETH_MIB_MAC_RECEIVE_ERROR 0x70 +#define ETH_MIB_BAD_CRC_EVENT 0x74 +#define ETH_MIB_COLLISION 0x78 +#define ETH_MIB_LATE_COLLISION 0x7c + +/* Port serial status reg (PSR) */ +#define ETH_INTERFACE_PCM 0x00000001 +#define ETH_LINK_IS_UP 0x00000002 +#define ETH_PORT_AT_FULL_DUPLEX 0x00000004 +#define ETH_RX_FLOW_CTRL_ENABLED 0x00000008 +#define ETH_GMII_SPEED_1000 0x00000010 +#define ETH_MII_SPEED_100 0x00000020 +#define ETH_TX_IN_PROGRESS 0x00000080 +#define ETH_BYPASS_ACTIVE 0x00000100 +#define ETH_PORT_AT_PARTITION_STATE 0x00000200 +#define ETH_PORT_TX_FIFO_EMPTY 0x00000400 + +/* SMI reg */ +#define ETH_SMI_BUSY 0x10000000 /* 0 - Write, 1 - Read */ +#define ETH_SMI_READ_VALID 0x08000000 /* 0 - Write, 1 - Read */ +#define ETH_SMI_OPCODE_WRITE 0 /* Completion of Read */ +#define ETH_SMI_OPCODE_READ 0x04000000 /* Operation is in progress */ + +/* Interrupt Cause Register Bit Definitions */ + +/* SDMA command status fields macros */ + +/* Tx & Rx descriptors status */ +#define ETH_ERROR_SUMMARY 0x00000001 + +/* Tx & Rx descriptors command */ +#define ETH_BUFFER_OWNED_BY_DMA 0x80000000 + +/* Tx descriptors status */ +#define ETH_LC_ERROR 0 +#define ETH_UR_ERROR 0x00000002 +#define ETH_RL_ERROR 0x00000004 +#define ETH_LLC_SNAP_FORMAT 0x00000200 + +/* Rx descriptors status */ +#define ETH_OVERRUN_ERROR 0x00000002 +#define ETH_MAX_FRAME_LENGTH_ERROR 0x00000004 +#define ETH_RESOURCE_ERROR 0x00000006 +#define ETH_VLAN_TAGGED 0x00080000 +#define ETH_BPDU_FRAME 0x00100000 +#define ETH_UDP_FRAME_OVER_IP_V_4 0x00200000 +#define ETH_OTHER_FRAME_TYPE 0x00400000 +#define ETH_LAYER_2_IS_ETH_V_2 0x00800000 +#define ETH_FRAME_TYPE_IP_V_4 0x01000000 +#define ETH_FRAME_HEADER_OK 0x02000000 +#define ETH_RX_LAST_DESC 0x04000000 +#define ETH_RX_FIRST_DESC 0x08000000 +#define ETH_UNKNOWN_DESTINATION_ADDR 0x10000000 +#define ETH_RX_ENABLE_INTERRUPT 0x20000000 +#define ETH_LAYER_4_CHECKSUM_OK 0x40000000 + +/* Rx descriptors byte count */ +#define ETH_FRAME_FRAGMENTED 0x00000004 + +/* Tx descriptors command */ +#define ETH_LAYER_4_CHECKSUM_FIRST_DESC 0x00000400 +#define ETH_FRAME_SET_TO_VLAN 0x00008000 +#define ETH_UDP_FRAME 0x00010000 +#define ETH_GEN_TCP_UDP_CHECKSUM 0x00020000 +#define ETH_GEN_IP_V_4_CHECKSUM 0x00040000 +#define ETH_ZERO_PADDING 0x00080000 +#define ETH_TX_LAST_DESC 0x00100000 +#define ETH_TX_FIRST_DESC 0x00200000 +#define ETH_GEN_CRC 0x00400000 +#define ETH_TX_ENABLE_INTERRUPT 0x00800000 +#define ETH_AUTO_MODE 0x40000000 + +#define ETH_TX_IHL_SHIFT 11 + +/* typedefs */ + +typedef enum _eth_func_ret_status { + ETH_OK, /* Returned as expected. */ + ETH_ERROR, /* Fundamental error. */ + ETH_RETRY, /* Could not process request. Try later.*/ + ETH_END_OF_JOB, /* Ring has nothing to process. */ + ETH_QUEUE_FULL, /* Ring resource error. */ + ETH_QUEUE_LAST_RESOURCE /* Ring resources about to exhaust. */ +} ETH_FUNC_RET_STATUS; + +typedef enum _eth_target { + ETH_TARGET_DRAM, + ETH_TARGET_DEVICE, + ETH_TARGET_CBS, + ETH_TARGET_PCI0, + ETH_TARGET_PCI1 +} ETH_TARGET; + +/* These are for big-endian machines. Little endian needs different + * definitions. + */ +#if defined(__BIG_ENDIAN) +struct eth_rx_desc { + u16 byte_cnt; /* Descriptor buffer byte count */ + u16 buf_size; /* Buffer size */ + u32 cmd_sts; /* Descriptor command status */ + u32 next_desc_ptr; /* Next descriptor pointer */ + u32 buf_ptr; /* Descriptor buffer pointer */ +}; + +struct eth_tx_desc { + u16 byte_cnt; /* buffer byte count */ + u16 l4i_chk; /* CPU provided TCP checksum */ + u32 cmd_sts; /* Command/status field */ + u32 next_desc_ptr; /* Pointer to next descriptor */ + u32 buf_ptr; /* pointer to buffer for this descriptor*/ +}; +#elif defined(__LITTLE_ENDIAN) +struct eth_rx_desc { + u32 cmd_sts; /* Descriptor command status */ + u16 buf_size; /* Buffer size */ + u16 byte_cnt; /* Descriptor buffer byte count */ + u32 buf_ptr; /* Descriptor buffer pointer */ + u32 next_desc_ptr; /* Next descriptor pointer */ +}; + +struct eth_tx_desc { + u32 cmd_sts; /* Command/status field */ + u16 l4i_chk; /* CPU provided TCP checksum */ + u16 byte_cnt; /* buffer byte count */ + u32 buf_ptr; /* pointer to buffer for this descriptor*/ + u32 next_desc_ptr; /* Pointer to next descriptor */ +}; +#else +#error One of __BIG_ENDIAN or __LITTLE_ENDIAN must be defined +#endif + +/* Unified struct for Rx and Tx operations. The user is not required to */ +/* be familier with neither Tx nor Rx descriptors. */ +struct pkt_info { + unsigned short byte_cnt; /* Descriptor buffer byte count */ + unsigned short l4i_chk; /* Tx CPU provided TCP Checksum */ + unsigned int cmd_sts; /* Descriptor command status */ + dma_addr_t buf_ptr; /* Descriptor buffer pointer */ + struct sk_buff *return_info; /* User resource return information */ +}; + +/* Ethernet port specific information */ +struct mv643xx_mib_counters { + u64 good_octets_received; + u32 bad_octets_received; + u32 internal_mac_transmit_err; + u32 good_frames_received; + u32 bad_frames_received; + u32 broadcast_frames_received; + u32 multicast_frames_received; + u32 frames_64_octets; + u32 frames_65_to_127_octets; + u32 frames_128_to_255_octets; + u32 frames_256_to_511_octets; + u32 frames_512_to_1023_octets; + u32 frames_1024_to_max_octets; + u64 good_octets_sent; + u32 good_frames_sent; + u32 excessive_collision; + u32 multicast_frames_sent; + u32 broadcast_frames_sent; + u32 unrec_mac_control_received; + u32 fc_sent; + u32 good_fc_received; + u32 bad_fc_received; + u32 undersize_received; + u32 fragments_received; + u32 oversize_received; + u32 jabber_received; + u32 mac_receive_error; + u32 bad_crc_event; + u32 collision; + u32 late_collision; +}; + +struct mv643xx_private { + int port_num; /* User Ethernet port number */ + + u32 rx_sram_addr; /* Base address of rx sram area */ + u32 rx_sram_size; /* Size of rx sram area */ + u32 tx_sram_addr; /* Base address of tx sram area */ + u32 tx_sram_size; /* Size of tx sram area */ + + int rx_resource_err; /* Rx ring resource error flag */ + + /* Tx/Rx rings managment indexes fields. For driver use */ + + /* Next available and first returning Rx resource */ + int rx_curr_desc_q, rx_used_desc_q; + + /* Next available and first returning Tx resource */ + int tx_curr_desc_q, tx_used_desc_q; + +#ifdef MV643XX_TX_FAST_REFILL + u32 tx_clean_threshold; +#endif + + struct eth_rx_desc *p_rx_desc_area; + dma_addr_t rx_desc_dma; + int rx_desc_area_size; + struct sk_buff **rx_skb; + + struct eth_tx_desc *p_tx_desc_area; + dma_addr_t tx_desc_dma; + int tx_desc_area_size; + struct sk_buff **tx_skb; + + struct work_struct tx_timeout_task; + + struct net_device *dev; + struct napi_struct napi; + struct net_device_stats stats; + struct mv643xx_mib_counters mib_counters; + spinlock_t lock; + /* Size of Tx Ring per queue */ + int tx_ring_size; + /* Number of tx descriptors in use */ + int tx_desc_count; + /* Size of Rx Ring per queue */ + int rx_ring_size; + /* Number of rx descriptors in use */ + int rx_desc_count; + + /* + * Used in case RX Ring is empty, which can be caused when + * system does not have resources (skb's) + */ + struct timer_list timeout; + + u32 rx_int_coal; + u32 tx_int_coal; + struct mii_if_info mii; +}; /* Static function declarations */ +static void eth_port_init(struct mv643xx_private *mp); +static void eth_port_reset(unsigned int eth_port_num); +static void eth_port_start(struct net_device *dev); + +static void ethernet_phy_reset(unsigned int eth_port_num); + +static void eth_port_write_smi_reg(unsigned int eth_port_num, + unsigned int phy_reg, unsigned int value); + +static void eth_port_read_smi_reg(unsigned int eth_port_num, + unsigned int phy_reg, unsigned int *value); + +static void eth_clear_mib_counters(unsigned int eth_port_num); + +static ETH_FUNC_RET_STATUS eth_port_receive(struct mv643xx_private *mp, + struct pkt_info *p_pkt_info); +static ETH_FUNC_RET_STATUS eth_rx_return_buff(struct mv643xx_private *mp, + struct pkt_info *p_pkt_info); + static void eth_port_uc_addr_get(unsigned int port_num, unsigned char *p_addr); static void eth_port_uc_addr_set(unsigned int port_num, unsigned char *p_addr); static void eth_port_set_multicast_list(struct net_device *); -- cgit v1.2.3