From bdab4e877819cc8b682797901c8b37567fec3c5e Mon Sep 17 00:00:00 2001 From: "Darrick J. Wong" Date: Fri, 13 Oct 2006 16:56:25 -0700 Subject: [SCSI] libsas: support NCQ for SATA disks This patch adds SATAII NCQ support to libsas. Both the use_ncq and the dma_xfer flags in ata_task must be set for NCQ to work correctly on the Adaptec SAS controller. The rest of the patch adds ATA_FLAG_NCQ to sata_port_info and sets up ap->scsi_host so that ata_setup_ncq doesn't crash. Please note that this patch is against the aic94xx-sas git tree, not scsi-misc. Thanks also to James Bottomley for providing an earlier version of this patch from which to work. I've tested this patch on a x206m with a ST380819AS SATA2 disk plugged into the Adaptec SAS controller. The drive came up with a queue depth of 31, and I successfully ran an I/O flood test to coerce libata into sending multiple commands simultaneously. A kernel probe recorded the maximum tag number that had been seen before and after the flood test; before the test it was 2 and after it was 30, as I expected. Signed-off-by: Darrick J. Wong Signed-off-by: James Bottomley --- drivers/scsi/libsas/sas_scsi_host.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers/scsi/libsas') diff --git a/drivers/scsi/libsas/sas_scsi_host.c b/drivers/scsi/libsas/sas_scsi_host.c index 3220b3fc6b2..274e7eb47f3 100644 --- a/drivers/scsi/libsas/sas_scsi_host.c +++ b/drivers/scsi/libsas/sas_scsi_host.c @@ -828,8 +828,14 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc) task->ata_task.retry_count = 1; task->task_state_flags = SAS_TASK_STATE_PENDING; - if (qc->tf.protocol == ATA_PROT_DMA) + switch (qc->tf.protocol) { + case ATA_PROT_NCQ: + task->ata_task.use_ncq = 1; + /* fall through */ + case ATA_PROT_DMA: task->ata_task.dma_xfer = 1; + break; + } if (sas_ha->lldd_max_execute_num < 2) res = i->dft->lldd_execute_task(task, 1, GFP_ATOMIC); @@ -962,7 +968,7 @@ static struct ata_port_operations sas_sata_ops = { static struct ata_port_info sata_port_info = { .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_SATA_RESET | - ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA, + ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | ATA_FLAG_NCQ, .pio_mask = 0x1f, /* PIO0-4 */ .mwdma_mask = 0x07, /* MWDMA0-2 */ .udma_mask = ATA_UDMA6, @@ -1031,6 +1037,7 @@ int sas_target_alloc(struct scsi_target *starget) ap->private_data = found_dev; ap->cbl = ATA_CBL_SATA; + ap->scsi_host = shost; found_dev->sata_dev.ap = ap; } -- cgit v1.2.3