From 7e36e2f5355ab87f8946041d044b34cda01e2077 Mon Sep 17 00:00:00 2001 From: Rod Whitby Date: Tue, 1 Apr 2008 10:53:23 +0100 Subject: [ARM] 4874/2: ixp4xx: Add support for the Freecom FSG-3 board The Freecom-FSG3 is a small network-attached-storage device with the following feature set: * Intel IXP422 * 4MB Flash (ixp4xx flash driver) * 64MB RAM * 4 USB 2.0 host ports (ehci and ohci drivers) * 1 WAN (eth1) and 3 LAN (eth0) ethernet ports * Supported by the open source ixp4xx ethernet driver * Via VT6421 disk controller (libata and sata-via drivers) * Internal hard disk (PATA supported, SATA not yet supported) * External SATA port (not yet supported) * ISL1208 RTC chip * Winbond 83782 temp sensor and fan controller * MiniPCI slot The ixp4xx_defconfig is also updated to support this device (the leds-fsg driver is to be submitted separately via the leds tree after this initial support is merged, as it depends on header gpio defines). Signed-off-by: Rod Whitby Signed-off-by: Russell King --- include/asm-arm/arch-ixp4xx/fsg.h | 50 ++++++++++++++++++++++++++++++++++ include/asm-arm/arch-ixp4xx/hardware.h | 1 + include/asm-arm/arch-ixp4xx/irqs.h | 7 +++++ 3 files changed, 58 insertions(+) create mode 100644 include/asm-arm/arch-ixp4xx/fsg.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-ixp4xx/fsg.h b/include/asm-arm/arch-ixp4xx/fsg.h new file mode 100644 index 00000000000..c0100cc7981 --- /dev/null +++ b/include/asm-arm/arch-ixp4xx/fsg.h @@ -0,0 +1,50 @@ +/* + * include/asm-arm/arch-ixp4xx/fsg.h + * + * Freecom FSG-3 platform specific definitions + * + * Author: Rod Whitby + * Author: Tomasz Chmielewski + * Maintainers: http://www.nslu2-linux.org + * + * Based on coyote.h by + * Copyright 2004 (c) MontaVista, Software, Inc. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_HARDWARE_H__ +#error "Do not include this directly, instead #include " +#endif + +#define FSG_SDA_PIN 12 +#define FSG_SCL_PIN 13 + +/* + * FSG PCI IRQs + */ +#define FSG_PCI_MAX_DEV 3 +#define FSG_PCI_IRQ_LINES 3 + + +/* PCI controller GPIO to IRQ pin mappings */ +#define FSG_PCI_INTA_PIN 6 +#define FSG_PCI_INTB_PIN 7 +#define FSG_PCI_INTC_PIN 5 + +/* Buttons */ + +#define FSG_SB_GPIO 4 /* sync button */ +#define FSG_RB_GPIO 9 /* reset button */ +#define FSG_UB_GPIO 10 /* usb button */ + +/* LEDs */ + +#define FSG_LED_WLAN_BIT 0 +#define FSG_LED_WAN_BIT 1 +#define FSG_LED_SATA_BIT 2 +#define FSG_LED_USB_BIT 4 +#define FSG_LED_RING_BIT 5 +#define FSG_LED_SYNC_BIT 7 diff --git a/include/asm-arm/arch-ixp4xx/hardware.h b/include/asm-arm/arch-ixp4xx/hardware.h index 73e8dc36f6a..fa723a62785 100644 --- a/include/asm-arm/arch-ixp4xx/hardware.h +++ b/include/asm-arm/arch-ixp4xx/hardware.h @@ -45,5 +45,6 @@ #include "nslu2.h" #include "nas100d.h" #include "dsmg600.h" +#include "fsg.h" #endif /* _ASM_ARCH_HARDWARE_H */ diff --git a/include/asm-arm/arch-ixp4xx/irqs.h b/include/asm-arm/arch-ixp4xx/irqs.h index 11801605047..674af4a8414 100644 --- a/include/asm-arm/arch-ixp4xx/irqs.h +++ b/include/asm-arm/arch-ixp4xx/irqs.h @@ -128,4 +128,11 @@ #define IRQ_DSMG600_PCI_INTE IRQ_IXP4XX_GPIO7 #define IRQ_DSMG600_PCI_INTF IRQ_IXP4XX_GPIO6 +/* + * Freecom FSG-3 Board IRQs + */ +#define IRQ_FSG_PCI_INTA IRQ_IXP4XX_GPIO6 +#define IRQ_FSG_PCI_INTB IRQ_IXP4XX_GPIO7 +#define IRQ_FSG_PCI_INTC IRQ_IXP4XX_GPIO5 + #endif -- cgit v1.2.3 From e055d5bff318845f99c0fbf93245767fab8dce88 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Tue, 22 Apr 2008 01:43:27 +0100 Subject: [ARM] 5015/1: arm: remove ARCH_CO285 Trying to compile a kerel for ARCH_CO285 fails with the following error: <-- snip --> ... CC arch/arm/mach-footbridge/dc21285.o /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c: In function 'dc21285_base_address': /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: 'PCICFG0_BASE' undeclared (first use in this function) /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: (Each undeclared identifier is reported only once /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: for each function it appears in.) /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:57: error: 'PCICFG1_BASE' undeclared (first use in this function) /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c: In function 'dc21285_scan_bus': /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:286: error: implicit declaration of function 'pci_scan_bus' ... make[2]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1 <-- snip --> This does not seem to be a recent breakage. The ARCH_CO285 support is old - kernel 2.2.0 contains first traces of it, an it seems to have been pretty complete in later 2.2 kernels. Since it seems to be completely dead code now this patch therefore removes it. Signed-off-by: Adrian Bunk Signed-off-by: Russell King --- include/asm-arm/arch-ebsa285/hardware.h | 26 -------------------------- include/asm-arm/arch-ebsa285/memory.h | 19 ------------------- include/asm-arm/arch-ebsa285/vmalloc.h | 4 ---- 3 files changed, 49 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-ebsa285/hardware.h b/include/asm-arm/arch-ebsa285/hardware.h index daad8ee2d19..74610c2c63d 100644 --- a/include/asm-arm/arch-ebsa285/hardware.h +++ b/include/asm-arm/arch-ebsa285/hardware.h @@ -14,7 +14,6 @@ #include -#ifdef CONFIG_ARCH_FOOTBRIDGE /* Virtual Physical Size * 0xff800000 0x40000000 1MB X-Bus * 0xff000000 0x7c000000 1MB PCI I/O space @@ -50,31 +49,6 @@ #define PCIMEM_SIZE 0x01000000 #define PCIMEM_BASE 0xf0000000 -#elif defined(CONFIG_ARCH_CO285) -/* - * This is the COEBSA285 cut-down mapping - */ -#define PCIMEM_SIZE 0x80000000 -#define PCIMEM_BASE 0x80000000 - -#define WFLUSH_SIZE 0x01000000 -#define WFLUSH_BASE 0x7d000000 - -#define ARMCSR_SIZE 0x00100000 -#define ARMCSR_BASE 0x7cf00000 - -#define XBUS_SIZE 0x00020000 -#define XBUS_BASE 0x7cee0000 - -#define PCIO_SIZE 0x00010000 -#define PCIO_BASE 0x7ced0000 - -#else - -#error "Undefined footbridge architecture" - -#endif - #define XBUS_LEDS ((volatile unsigned char *)(XBUS_BASE + 0x12000)) #define XBUS_LED_AMBER (1 << 0) #define XBUS_LED_GREEN (1 << 1) diff --git a/include/asm-arm/arch-ebsa285/memory.h b/include/asm-arm/arch-ebsa285/memory.h index cbd7ae64bcc..9019a3bf5ab 100644 --- a/include/asm-arm/arch-ebsa285/memory.h +++ b/include/asm-arm/arch-ebsa285/memory.h @@ -42,8 +42,6 @@ extern unsigned long __bus_to_virt(unsigned long); #endif -#if defined(CONFIG_ARCH_FOOTBRIDGE) - /* Task size and page offset at 3GB */ #define TASK_SIZE UL(0xbf000000) #define PAGE_OFFSET UL(0xc0000000) @@ -53,23 +51,6 @@ extern unsigned long __bus_to_virt(unsigned long); */ #define FLUSH_BASE 0xf9000000 -#elif defined(CONFIG_ARCH_CO285) - -/* Task size and page offset at 1.5GB */ -#define TASK_SIZE UL(0x5f000000) -#define PAGE_OFFSET UL(0x60000000) - -/* - * Cache flushing area. - */ -#define FLUSH_BASE 0x7e000000 - -#else - -#error "Undefined footbridge architecture" - -#endif - /* * Physical DRAM offset. */ diff --git a/include/asm-arm/arch-ebsa285/vmalloc.h b/include/asm-arm/arch-ebsa285/vmalloc.h index 02598200997..e487d7e8c8a 100644 --- a/include/asm-arm/arch-ebsa285/vmalloc.h +++ b/include/asm-arm/arch-ebsa285/vmalloc.h @@ -7,8 +7,4 @@ */ -#ifdef CONFIG_ARCH_FOOTBRIDGE #define VMALLOC_END (PAGE_OFFSET + 0x30000000) -#else -#define VMALLOC_END (PAGE_OFFSET + 0x20000000) -#endif -- cgit v1.2.3 From 205bee6ad804d7034773b5978c74dde495df2301 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 13:57:26 +0100 Subject: [ARM] dyntick: Remove obsolete and unused ARM dyntick support dyntick is superseded by the clocksource/clockevent infrastructure, using the NO_HZ configuration option. No one implements dyntick on ARM anymore, so it's pointless keeping it around. Remove dyntick support. Signed-off-by: Russell King --- include/asm-arm/dyntick.h | 6 ------ include/asm-arm/hw_irq.h | 11 ----------- include/asm-arm/mach/time.h | 22 ---------------------- 3 files changed, 39 deletions(-) delete mode 100644 include/asm-arm/dyntick.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/dyntick.h b/include/asm-arm/dyntick.h deleted file mode 100644 index 19fab2d2b76..00000000000 --- a/include/asm-arm/dyntick.h +++ /dev/null @@ -1,6 +0,0 @@ -#ifndef _ASMARM_DYNTICK_H -#define _ASMARM_DYNTICK_H - -#include - -#endif /* _ASMARM_DYNTICK_H */ diff --git a/include/asm-arm/hw_irq.h b/include/asm-arm/hw_irq.h index 98d594a973d..f1a08a50060 100644 --- a/include/asm-arm/hw_irq.h +++ b/include/asm-arm/hw_irq.h @@ -6,15 +6,4 @@ #include -#if defined(CONFIG_NO_IDLE_HZ) -# include -# define handle_dynamic_tick(action) \ - if (!(action->flags & IRQF_TIMER) && system_timer->dyn_tick) { \ - write_seqlock(&xtime_lock); \ - if (system_timer->dyn_tick->state & DYN_TICK_ENABLED) \ - system_timer->dyn_tick->handler(irq, NULL); \ - write_sequnlock(&xtime_lock); \ - } -#endif - #endif diff --git a/include/asm-arm/mach/time.h b/include/asm-arm/mach/time.h index 5dc357013b7..2fd36ea0130 100644 --- a/include/asm-arm/mach/time.h +++ b/include/asm-arm/mach/time.h @@ -41,30 +41,8 @@ struct sys_timer { #ifndef CONFIG_GENERIC_TIME unsigned long (*offset)(void); #endif - -#ifdef CONFIG_NO_IDLE_HZ - struct dyn_tick_timer *dyn_tick; -#endif -}; - -#ifdef CONFIG_NO_IDLE_HZ - -#define DYN_TICK_ENABLED (1 << 1) - -struct dyn_tick_timer { - spinlock_t lock; - unsigned int state; /* Current state */ - int (*enable)(void); /* Enables dynamic tick */ - int (*disable)(void); /* Disables dynamic tick */ - void (*reprogram)(unsigned long); /* Reprograms the timer */ - int (*handler)(int, void *); }; -void timer_dyn_reprogram(void); -#else -#define timer_dyn_reprogram() do { } while (0) -#endif - extern struct sys_timer *system_timer; extern void timer_tick(void); -- cgit v1.2.3 From 284d115ec9b70d7c38752d10ad393a198db07a4b Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 17:32:16 +0100 Subject: [ARM] pxa: separate PXA25x and PXA27x UDC register definitions The PXA25x and PXA27x USB device controller register definitions are different. Currently, they live side by side in pxa-regs.h, but only one set is available depending on the setting of PXA25x or PXA27x. This means that if we build to support both PXA25x and PXA27x, the PXA27x definitions are unavailable, even to PXA27x specific code. Remove these definitions from pxa-regs.h, and place them in separate files. Include these files where appropriate. Note: according to the dependencies in drivers/usb/gadget/Kconfig, we do not support the UDC on PXA27x nor PXA3xx CPUs, so remove the platform devices from pxa27x.c and pxa3xx.c. Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa-regs.h | 412 ---------------------------------- include/asm-arm/arch-pxa/pxa25x-udc.h | 163 ++++++++++++++ include/asm-arm/arch-pxa/pxa27x-udc.h | 256 +++++++++++++++++++++ 3 files changed, 419 insertions(+), 412 deletions(-) create mode 100644 include/asm-arm/arch-pxa/pxa25x-udc.h create mode 100644 include/asm-arm/arch-pxa/pxa27x-udc.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h index 4b2ea1e95c5..68d74287730 100644 --- a/include/asm-arm/arch-pxa/pxa-regs.h +++ b/include/asm-arm/arch-pxa/pxa-regs.h @@ -599,418 +599,6 @@ #define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */ -/* - * USB Device Controller - * PXA25x and PXA27x USB device controller registers are different. - */ -#if defined(CONFIG_PXA25x) - -#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */ -#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */ -#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */ - -#define UDCCR __REG(0x40600000) /* UDC Control Register */ -#define UDCCR_UDE (1 << 0) /* UDC enable */ -#define UDCCR_UDA (1 << 1) /* UDC active */ -#define UDCCR_RSM (1 << 2) /* Device resume */ -#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */ -#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */ -#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */ -#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */ -#define UDCCR_REM (1 << 7) /* Reset interrupt mask */ - -#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */ -#define UDCCS0_OPR (1 << 0) /* OUT packet ready */ -#define UDCCS0_IPR (1 << 1) /* IN packet ready */ -#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */ -#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */ -#define UDCCS0_SST (1 << 4) /* Sent stall */ -#define UDCCS0_FST (1 << 5) /* Force stall */ -#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */ -#define UDCCS0_SA (1 << 7) /* Setup active */ - -/* Bulk IN - Endpoint 1,6,11 */ -#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */ -#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */ -#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */ - -#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */ -#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */ -#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */ -#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */ -#define UDCCS_BI_SST (1 << 4) /* Sent stall */ -#define UDCCS_BI_FST (1 << 5) /* Force stall */ -#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */ - -/* Bulk OUT - Endpoint 2,7,12 */ -#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */ -#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */ -#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */ - -#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */ -#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */ -#define UDCCS_BO_DME (1 << 3) /* DMA enable */ -#define UDCCS_BO_SST (1 << 4) /* Sent stall */ -#define UDCCS_BO_FST (1 << 5) /* Force stall */ -#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */ -#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */ - -/* Isochronous IN - Endpoint 3,8,13 */ -#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */ -#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */ -#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */ - -#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */ -#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */ -#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */ -#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */ -#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */ - -/* Isochronous OUT - Endpoint 4,9,14 */ -#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */ -#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */ -#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */ - -#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */ -#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */ -#define UDCCS_IO_ROF (1 << 2) /* Receive overflow */ -#define UDCCS_IO_DME (1 << 3) /* DMA enable */ -#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */ -#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */ - -/* Interrupt IN - Endpoint 5,10,15 */ -#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */ -#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */ -#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */ - -#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */ -#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */ -#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */ -#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */ -#define UDCCS_INT_SST (1 << 4) /* Sent stall */ -#define UDCCS_INT_FST (1 << 5) /* Force stall */ -#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */ - -#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */ -#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */ -#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */ -#define UBCR4 __REG(0x4060006c) /* UDC Byte Count Reg 4 */ -#define UBCR7 __REG(0x40600070) /* UDC Byte Count Reg 7 */ -#define UBCR9 __REG(0x40600074) /* UDC Byte Count Reg 9 */ -#define UBCR12 __REG(0x40600078) /* UDC Byte Count Reg 12 */ -#define UBCR14 __REG(0x4060007c) /* UDC Byte Count Reg 14 */ -#define UDDR0 __REG(0x40600080) /* UDC Endpoint 0 Data Register */ -#define UDDR1 __REG(0x40600100) /* UDC Endpoint 1 Data Register */ -#define UDDR2 __REG(0x40600180) /* UDC Endpoint 2 Data Register */ -#define UDDR3 __REG(0x40600200) /* UDC Endpoint 3 Data Register */ -#define UDDR4 __REG(0x40600400) /* UDC Endpoint 4 Data Register */ -#define UDDR5 __REG(0x406000A0) /* UDC Endpoint 5 Data Register */ -#define UDDR6 __REG(0x40600600) /* UDC Endpoint 6 Data Register */ -#define UDDR7 __REG(0x40600680) /* UDC Endpoint 7 Data Register */ -#define UDDR8 __REG(0x40600700) /* UDC Endpoint 8 Data Register */ -#define UDDR9 __REG(0x40600900) /* UDC Endpoint 9 Data Register */ -#define UDDR10 __REG(0x406000C0) /* UDC Endpoint 10 Data Register */ -#define UDDR11 __REG(0x40600B00) /* UDC Endpoint 11 Data Register */ -#define UDDR12 __REG(0x40600B80) /* UDC Endpoint 12 Data Register */ -#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */ -#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */ -#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */ - -#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */ - -#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */ -#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */ -#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */ -#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */ -#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */ -#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */ -#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */ -#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */ - -#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */ - -#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */ -#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */ -#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */ -#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */ -#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */ -#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */ -#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */ -#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */ - -#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */ - -#define USIR0_IR0 (1 << 0) /* Interrupt request ep 0 */ -#define USIR0_IR1 (1 << 1) /* Interrupt request ep 1 */ -#define USIR0_IR2 (1 << 2) /* Interrupt request ep 2 */ -#define USIR0_IR3 (1 << 3) /* Interrupt request ep 3 */ -#define USIR0_IR4 (1 << 4) /* Interrupt request ep 4 */ -#define USIR0_IR5 (1 << 5) /* Interrupt request ep 5 */ -#define USIR0_IR6 (1 << 6) /* Interrupt request ep 6 */ -#define USIR0_IR7 (1 << 7) /* Interrupt request ep 7 */ - -#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */ - -#define USIR1_IR8 (1 << 0) /* Interrupt request ep 8 */ -#define USIR1_IR9 (1 << 1) /* Interrupt request ep 9 */ -#define USIR1_IR10 (1 << 2) /* Interrupt request ep 10 */ -#define USIR1_IR11 (1 << 3) /* Interrupt request ep 11 */ -#define USIR1_IR12 (1 << 4) /* Interrupt request ep 12 */ -#define USIR1_IR13 (1 << 5) /* Interrupt request ep 13 */ -#define USIR1_IR14 (1 << 6) /* Interrupt request ep 14 */ -#define USIR1_IR15 (1 << 7) /* Interrupt request ep 15 */ - -#elif defined(CONFIG_PXA27x) - -#define UDCCR __REG(0x40600000) /* UDC Control Register */ -#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */ -#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation - Protocol Port Support */ -#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol - Support */ -#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol - Enable */ -#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */ -#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */ -#define UDCCR_ACN_S 11 -#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */ -#define UDCCR_AIN_S 8 -#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface - Setting Number */ -#define UDCCR_AAISN_S 5 -#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active - Configuration */ -#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration - Error */ -#define UDCCR_UDR (1 << 2) /* UDC Resume */ -#define UDCCR_UDA (1 << 1) /* UDC Active */ -#define UDCCR_UDE (1 << 0) /* UDC Enable */ - -#define UDCICR0 __REG(0x40600004) /* UDC Interrupt Control Register0 */ -#define UDCICR1 __REG(0x40600008) /* UDC Interrupt Control Register1 */ -#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */ -#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */ - -#define UDC_INT_FIFOERROR (0x2) -#define UDC_INT_PACKETCMP (0x1) - -#define UDCICR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) -#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */ -#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */ -#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */ -#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */ -#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */ - -#define UDCISR0 __REG(0x4060000C) /* UDC Interrupt Status Register 0 */ -#define UDCISR1 __REG(0x40600010) /* UDC Interrupt Status Register 1 */ -#define UDCISR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) -#define UDCISR1_IRCC (1 << 31) /* IntReq - Configuration Change */ -#define UDCISR1_IRSOF (1 << 30) /* IntReq - Start of Frame */ -#define UDCISR1_IRRU (1 << 29) /* IntReq - Resume */ -#define UDCISR1_IRSU (1 << 28) /* IntReq - Suspend */ -#define UDCISR1_IRRS (1 << 27) /* IntReq - Reset */ - -#define UDCFNR __REG(0x40600014) /* UDC Frame Number Register */ -#define UDCOTGICR __REG(0x40600018) /* UDC On-The-Go interrupt control */ -#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */ -#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt - Rising Edge Interrupt Enable */ -#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt - Falling Edge Interrupt Enable */ -#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge - Interrupt Enable */ -#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge - Interrupt Enable */ -#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge - Interrupt Enable */ -#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge - Interrupt Enable */ -#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge - Interrupt Enable */ -#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge - Interrupt Enable */ -#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising - Edge Interrupt Enable */ -#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling - Edge Interrupt Enable */ -#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge - Interrupt Enable */ -#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge - Interrupt Enable */ - -#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */ - -#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */ -#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */ -#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */ -#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */ -#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */ -#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */ -#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */ -#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */ -#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */ -#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */ -#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */ -#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */ -#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */ -#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */ - -#define UDCCSN(x) __REG2(0x40600100, (x) << 2) -#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */ -#define UDCCSR0_SA (1 << 7) /* Setup Active */ -#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */ -#define UDCCSR0_FST (1 << 5) /* Force Stall */ -#define UDCCSR0_SST (1 << 4) /* Sent Stall */ -#define UDCCSR0_DME (1 << 3) /* DMA Enable */ -#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */ -#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */ -#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */ - -#define UDCCSRA __REG(0x40600104) /* UDC Control/Status register - Endpoint A */ -#define UDCCSRB __REG(0x40600108) /* UDC Control/Status register - Endpoint B */ -#define UDCCSRC __REG(0x4060010C) /* UDC Control/Status register - Endpoint C */ -#define UDCCSRD __REG(0x40600110) /* UDC Control/Status register - Endpoint D */ -#define UDCCSRE __REG(0x40600114) /* UDC Control/Status register - Endpoint E */ -#define UDCCSRF __REG(0x40600118) /* UDC Control/Status register - Endpoint F */ -#define UDCCSRG __REG(0x4060011C) /* UDC Control/Status register - Endpoint G */ -#define UDCCSRH __REG(0x40600120) /* UDC Control/Status register - Endpoint H */ -#define UDCCSRI __REG(0x40600124) /* UDC Control/Status register - Endpoint I */ -#define UDCCSRJ __REG(0x40600128) /* UDC Control/Status register - Endpoint J */ -#define UDCCSRK __REG(0x4060012C) /* UDC Control/Status register - Endpoint K */ -#define UDCCSRL __REG(0x40600130) /* UDC Control/Status register - Endpoint L */ -#define UDCCSRM __REG(0x40600134) /* UDC Control/Status register - Endpoint M */ -#define UDCCSRN __REG(0x40600138) /* UDC Control/Status register - Endpoint N */ -#define UDCCSRP __REG(0x4060013C) /* UDC Control/Status register - Endpoint P */ -#define UDCCSRQ __REG(0x40600140) /* UDC Control/Status register - Endpoint Q */ -#define UDCCSRR __REG(0x40600144) /* UDC Control/Status register - Endpoint R */ -#define UDCCSRS __REG(0x40600148) /* UDC Control/Status register - Endpoint S */ -#define UDCCSRT __REG(0x4060014C) /* UDC Control/Status register - Endpoint T */ -#define UDCCSRU __REG(0x40600150) /* UDC Control/Status register - Endpoint U */ -#define UDCCSRV __REG(0x40600154) /* UDC Control/Status register - Endpoint V */ -#define UDCCSRW __REG(0x40600158) /* UDC Control/Status register - Endpoint W */ -#define UDCCSRX __REG(0x4060015C) /* UDC Control/Status register - Endpoint X */ - -#define UDCCSR_DPE (1 << 9) /* Data Packet Error */ -#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */ -#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */ -#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */ -#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */ -#define UDCCSR_FST (1 << 5) /* Force STALL */ -#define UDCCSR_SST (1 << 4) /* Sent STALL */ -#define UDCCSR_DME (1 << 3) /* DMA Enable */ -#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */ -#define UDCCSR_PC (1 << 1) /* Packet Complete */ -#define UDCCSR_FS (1 << 0) /* FIFO needs service */ - -#define UDCBCN(x) __REG2(0x40600200, (x)<<2) -#define UDCBCR0 __REG(0x40600200) /* Byte Count Register - EP0 */ -#define UDCBCRA __REG(0x40600204) /* Byte Count Register - EPA */ -#define UDCBCRB __REG(0x40600208) /* Byte Count Register - EPB */ -#define UDCBCRC __REG(0x4060020C) /* Byte Count Register - EPC */ -#define UDCBCRD __REG(0x40600210) /* Byte Count Register - EPD */ -#define UDCBCRE __REG(0x40600214) /* Byte Count Register - EPE */ -#define UDCBCRF __REG(0x40600218) /* Byte Count Register - EPF */ -#define UDCBCRG __REG(0x4060021C) /* Byte Count Register - EPG */ -#define UDCBCRH __REG(0x40600220) /* Byte Count Register - EPH */ -#define UDCBCRI __REG(0x40600224) /* Byte Count Register - EPI */ -#define UDCBCRJ __REG(0x40600228) /* Byte Count Register - EPJ */ -#define UDCBCRK __REG(0x4060022C) /* Byte Count Register - EPK */ -#define UDCBCRL __REG(0x40600230) /* Byte Count Register - EPL */ -#define UDCBCRM __REG(0x40600234) /* Byte Count Register - EPM */ -#define UDCBCRN __REG(0x40600238) /* Byte Count Register - EPN */ -#define UDCBCRP __REG(0x4060023C) /* Byte Count Register - EPP */ -#define UDCBCRQ __REG(0x40600240) /* Byte Count Register - EPQ */ -#define UDCBCRR __REG(0x40600244) /* Byte Count Register - EPR */ -#define UDCBCRS __REG(0x40600248) /* Byte Count Register - EPS */ -#define UDCBCRT __REG(0x4060024C) /* Byte Count Register - EPT */ -#define UDCBCRU __REG(0x40600250) /* Byte Count Register - EPU */ -#define UDCBCRV __REG(0x40600254) /* Byte Count Register - EPV */ -#define UDCBCRW __REG(0x40600258) /* Byte Count Register - EPW */ -#define UDCBCRX __REG(0x4060025C) /* Byte Count Register - EPX */ - -#define UDCDN(x) __REG2(0x40600300, (x)<<2) -#define PHYS_UDCDN(x) (0x40600300 + ((x)<<2)) -#define PUDCDN(x) (volatile u32 *)(io_p2v(PHYS_UDCDN((x)))) -#define UDCDR0 __REG(0x40600300) /* Data Register - EP0 */ -#define UDCDRA __REG(0x40600304) /* Data Register - EPA */ -#define UDCDRB __REG(0x40600308) /* Data Register - EPB */ -#define UDCDRC __REG(0x4060030C) /* Data Register - EPC */ -#define UDCDRD __REG(0x40600310) /* Data Register - EPD */ -#define UDCDRE __REG(0x40600314) /* Data Register - EPE */ -#define UDCDRF __REG(0x40600318) /* Data Register - EPF */ -#define UDCDRG __REG(0x4060031C) /* Data Register - EPG */ -#define UDCDRH __REG(0x40600320) /* Data Register - EPH */ -#define UDCDRI __REG(0x40600324) /* Data Register - EPI */ -#define UDCDRJ __REG(0x40600328) /* Data Register - EPJ */ -#define UDCDRK __REG(0x4060032C) /* Data Register - EPK */ -#define UDCDRL __REG(0x40600330) /* Data Register - EPL */ -#define UDCDRM __REG(0x40600334) /* Data Register - EPM */ -#define UDCDRN __REG(0x40600338) /* Data Register - EPN */ -#define UDCDRP __REG(0x4060033C) /* Data Register - EPP */ -#define UDCDRQ __REG(0x40600340) /* Data Register - EPQ */ -#define UDCDRR __REG(0x40600344) /* Data Register - EPR */ -#define UDCDRS __REG(0x40600348) /* Data Register - EPS */ -#define UDCDRT __REG(0x4060034C) /* Data Register - EPT */ -#define UDCDRU __REG(0x40600350) /* Data Register - EPU */ -#define UDCDRV __REG(0x40600354) /* Data Register - EPV */ -#define UDCDRW __REG(0x40600358) /* Data Register - EPW */ -#define UDCDRX __REG(0x4060035C) /* Data Register - EPX */ - -#define UDCCN(x) __REG2(0x40600400, (x)<<2) -#define UDCCRA __REG(0x40600404) /* Configuration register EPA */ -#define UDCCRB __REG(0x40600408) /* Configuration register EPB */ -#define UDCCRC __REG(0x4060040C) /* Configuration register EPC */ -#define UDCCRD __REG(0x40600410) /* Configuration register EPD */ -#define UDCCRE __REG(0x40600414) /* Configuration register EPE */ -#define UDCCRF __REG(0x40600418) /* Configuration register EPF */ -#define UDCCRG __REG(0x4060041C) /* Configuration register EPG */ -#define UDCCRH __REG(0x40600420) /* Configuration register EPH */ -#define UDCCRI __REG(0x40600424) /* Configuration register EPI */ -#define UDCCRJ __REG(0x40600428) /* Configuration register EPJ */ -#define UDCCRK __REG(0x4060042C) /* Configuration register EPK */ -#define UDCCRL __REG(0x40600430) /* Configuration register EPL */ -#define UDCCRM __REG(0x40600434) /* Configuration register EPM */ -#define UDCCRN __REG(0x40600438) /* Configuration register EPN */ -#define UDCCRP __REG(0x4060043C) /* Configuration register EPP */ -#define UDCCRQ __REG(0x40600440) /* Configuration register EPQ */ -#define UDCCRR __REG(0x40600444) /* Configuration register EPR */ -#define UDCCRS __REG(0x40600448) /* Configuration register EPS */ -#define UDCCRT __REG(0x4060044C) /* Configuration register EPT */ -#define UDCCRU __REG(0x40600450) /* Configuration register EPU */ -#define UDCCRV __REG(0x40600454) /* Configuration register EPV */ -#define UDCCRW __REG(0x40600458) /* Configuration register EPW */ -#define UDCCRX __REG(0x4060045C) /* Configuration register EPX */ - -#define UDCCONR_CN (0x03 << 25) /* Configuration Number */ -#define UDCCONR_CN_S (25) -#define UDCCONR_IN (0x07 << 22) /* Interface Number */ -#define UDCCONR_IN_S (22) -#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */ -#define UDCCONR_AISN_S (19) -#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */ -#define UDCCONR_EN_S (15) -#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */ -#define UDCCONR_ET_S (13) -#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */ -#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */ -#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */ -#define UDCCONR_ET_NU (0x00 << 13) /* Not used */ -#define UDCCONR_ED (1 << 12) /* Endpoint Direction */ -#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */ -#define UDCCONR_MPS_S (2) -#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */ -#define UDCCONR_EE (1 << 0) /* Endpoint Enable */ - - -#define UDC_INT_FIFOERROR (0x2) -#define UDC_INT_PACKETCMP (0x1) - -#define UDC_FNR_MASK (0x7ff) - -#define UDCCSR_WR_MASK (UDCCSR_DME|UDCCSR_FST) -#define UDC_BCR_MASK (0x3ff) -#endif - /* * Fast Infrared Communication Port */ diff --git a/include/asm-arm/arch-pxa/pxa25x-udc.h b/include/asm-arm/arch-pxa/pxa25x-udc.h new file mode 100644 index 00000000000..840305916b6 --- /dev/null +++ b/include/asm-arm/arch-pxa/pxa25x-udc.h @@ -0,0 +1,163 @@ +#ifndef _ASM_ARCH_PXA25X_UDC_H +#define _ASM_ARCH_PXA25X_UDC_H + +#ifdef _ASM_ARCH_PXA27X_UDC_H +#error You can't include both PXA25x and PXA27x UDC support +#endif + +#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */ +#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */ +#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */ + +#define UDCCR __REG(0x40600000) /* UDC Control Register */ +#define UDCCR_UDE (1 << 0) /* UDC enable */ +#define UDCCR_UDA (1 << 1) /* UDC active */ +#define UDCCR_RSM (1 << 2) /* Device resume */ +#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */ +#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */ +#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */ +#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */ +#define UDCCR_REM (1 << 7) /* Reset interrupt mask */ + +#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */ +#define UDCCS0_OPR (1 << 0) /* OUT packet ready */ +#define UDCCS0_IPR (1 << 1) /* IN packet ready */ +#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */ +#define UDCCS0_SST (1 << 4) /* Sent stall */ +#define UDCCS0_FST (1 << 5) /* Force stall */ +#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */ +#define UDCCS0_SA (1 << 7) /* Setup active */ + +/* Bulk IN - Endpoint 1,6,11 */ +#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */ +#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */ +#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */ + +#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_BI_SST (1 << 4) /* Sent stall */ +#define UDCCS_BI_FST (1 << 5) /* Force stall */ +#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */ + +/* Bulk OUT - Endpoint 2,7,12 */ +#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */ +#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */ +#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */ + +#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */ +#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */ +#define UDCCS_BO_DME (1 << 3) /* DMA enable */ +#define UDCCS_BO_SST (1 << 4) /* Sent stall */ +#define UDCCS_BO_FST (1 << 5) /* Force stall */ +#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */ +#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */ + +/* Isochronous IN - Endpoint 3,8,13 */ +#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */ +#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */ +#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */ + +#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */ + +/* Isochronous OUT - Endpoint 4,9,14 */ +#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */ +#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */ +#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */ + +#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */ +#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */ +#define UDCCS_IO_ROF (1 << 2) /* Receive overflow */ +#define UDCCS_IO_DME (1 << 3) /* DMA enable */ +#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */ +#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */ + +/* Interrupt IN - Endpoint 5,10,15 */ +#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */ +#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */ +#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */ + +#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_INT_SST (1 << 4) /* Sent stall */ +#define UDCCS_INT_FST (1 << 5) /* Force stall */ +#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */ + +#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */ +#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */ +#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */ +#define UBCR4 __REG(0x4060006c) /* UDC Byte Count Reg 4 */ +#define UBCR7 __REG(0x40600070) /* UDC Byte Count Reg 7 */ +#define UBCR9 __REG(0x40600074) /* UDC Byte Count Reg 9 */ +#define UBCR12 __REG(0x40600078) /* UDC Byte Count Reg 12 */ +#define UBCR14 __REG(0x4060007c) /* UDC Byte Count Reg 14 */ +#define UDDR0 __REG(0x40600080) /* UDC Endpoint 0 Data Register */ +#define UDDR1 __REG(0x40600100) /* UDC Endpoint 1 Data Register */ +#define UDDR2 __REG(0x40600180) /* UDC Endpoint 2 Data Register */ +#define UDDR3 __REG(0x40600200) /* UDC Endpoint 3 Data Register */ +#define UDDR4 __REG(0x40600400) /* UDC Endpoint 4 Data Register */ +#define UDDR5 __REG(0x406000A0) /* UDC Endpoint 5 Data Register */ +#define UDDR6 __REG(0x40600600) /* UDC Endpoint 6 Data Register */ +#define UDDR7 __REG(0x40600680) /* UDC Endpoint 7 Data Register */ +#define UDDR8 __REG(0x40600700) /* UDC Endpoint 8 Data Register */ +#define UDDR9 __REG(0x40600900) /* UDC Endpoint 9 Data Register */ +#define UDDR10 __REG(0x406000C0) /* UDC Endpoint 10 Data Register */ +#define UDDR11 __REG(0x40600B00) /* UDC Endpoint 11 Data Register */ +#define UDDR12 __REG(0x40600B80) /* UDC Endpoint 12 Data Register */ +#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */ +#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */ +#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */ + +#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */ + +#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */ +#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */ +#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */ +#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */ +#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */ +#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */ +#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */ +#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */ + +#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */ + +#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */ +#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */ +#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */ +#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */ +#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */ +#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */ +#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */ +#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */ + +#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */ + +#define USIR0_IR0 (1 << 0) /* Interrupt request ep 0 */ +#define USIR0_IR1 (1 << 1) /* Interrupt request ep 1 */ +#define USIR0_IR2 (1 << 2) /* Interrupt request ep 2 */ +#define USIR0_IR3 (1 << 3) /* Interrupt request ep 3 */ +#define USIR0_IR4 (1 << 4) /* Interrupt request ep 4 */ +#define USIR0_IR5 (1 << 5) /* Interrupt request ep 5 */ +#define USIR0_IR6 (1 << 6) /* Interrupt request ep 6 */ +#define USIR0_IR7 (1 << 7) /* Interrupt request ep 7 */ + +#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */ + +#define USIR1_IR8 (1 << 0) /* Interrupt request ep 8 */ +#define USIR1_IR9 (1 << 1) /* Interrupt request ep 9 */ +#define USIR1_IR10 (1 << 2) /* Interrupt request ep 10 */ +#define USIR1_IR11 (1 << 3) /* Interrupt request ep 11 */ +#define USIR1_IR12 (1 << 4) /* Interrupt request ep 12 */ +#define USIR1_IR13 (1 << 5) /* Interrupt request ep 13 */ +#define USIR1_IR14 (1 << 6) /* Interrupt request ep 14 */ +#define USIR1_IR15 (1 << 7) /* Interrupt request ep 15 */ + +#endif diff --git a/include/asm-arm/arch-pxa/pxa27x-udc.h b/include/asm-arm/arch-pxa/pxa27x-udc.h new file mode 100644 index 00000000000..9cf0b1f8811 --- /dev/null +++ b/include/asm-arm/arch-pxa/pxa27x-udc.h @@ -0,0 +1,256 @@ +#ifndef _ASM_ARCH_PXA27X_UDC_H +#define _ASM_ARCH_PXA27X_UDC_H + +#ifdef _ASM_ARCH_PXA25X_UDC_H +#error You can't include both PXA25x and PXA27x UDC support +#endif + +#define UDCCR __REG(0x40600000) /* UDC Control Register */ +#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */ +#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation + Protocol Port Support */ +#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol + Support */ +#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol + Enable */ +#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */ +#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */ +#define UDCCR_ACN_S 11 +#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */ +#define UDCCR_AIN_S 8 +#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface + Setting Number */ +#define UDCCR_AAISN_S 5 +#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active + Configuration */ +#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration + Error */ +#define UDCCR_UDR (1 << 2) /* UDC Resume */ +#define UDCCR_UDA (1 << 1) /* UDC Active */ +#define UDCCR_UDE (1 << 0) /* UDC Enable */ + +#define UDCICR0 __REG(0x40600004) /* UDC Interrupt Control Register0 */ +#define UDCICR1 __REG(0x40600008) /* UDC Interrupt Control Register1 */ +#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */ +#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */ + +#define UDC_INT_FIFOERROR (0x2) +#define UDC_INT_PACKETCMP (0x1) + +#define UDCICR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) +#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */ +#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */ +#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */ +#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */ +#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */ + +#define UDCISR0 __REG(0x4060000C) /* UDC Interrupt Status Register 0 */ +#define UDCISR1 __REG(0x40600010) /* UDC Interrupt Status Register 1 */ +#define UDCISR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) +#define UDCISR1_IRCC (1 << 31) /* IntReq - Configuration Change */ +#define UDCISR1_IRSOF (1 << 30) /* IntReq - Start of Frame */ +#define UDCISR1_IRRU (1 << 29) /* IntReq - Resume */ +#define UDCISR1_IRSU (1 << 28) /* IntReq - Suspend */ +#define UDCISR1_IRRS (1 << 27) /* IntReq - Reset */ + +#define UDCFNR __REG(0x40600014) /* UDC Frame Number Register */ +#define UDCOTGICR __REG(0x40600018) /* UDC On-The-Go interrupt control */ +#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */ +#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt + Rising Edge Interrupt Enable */ +#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt + Falling Edge Interrupt Enable */ +#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising + Edge Interrupt Enable */ +#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling + Edge Interrupt Enable */ +#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge + Interrupt Enable */ + +#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */ + +#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */ +#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */ +#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */ +#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */ +#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */ +#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */ +#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */ +#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */ +#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */ +#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */ +#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */ +#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */ +#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */ +#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */ + +#define UDCCSN(x) __REG2(0x40600100, (x) << 2) +#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */ +#define UDCCSR0_SA (1 << 7) /* Setup Active */ +#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */ +#define UDCCSR0_FST (1 << 5) /* Force Stall */ +#define UDCCSR0_SST (1 << 4) /* Sent Stall */ +#define UDCCSR0_DME (1 << 3) /* DMA Enable */ +#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */ +#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */ +#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */ + +#define UDCCSRA __REG(0x40600104) /* UDC Control/Status register - Endpoint A */ +#define UDCCSRB __REG(0x40600108) /* UDC Control/Status register - Endpoint B */ +#define UDCCSRC __REG(0x4060010C) /* UDC Control/Status register - Endpoint C */ +#define UDCCSRD __REG(0x40600110) /* UDC Control/Status register - Endpoint D */ +#define UDCCSRE __REG(0x40600114) /* UDC Control/Status register - Endpoint E */ +#define UDCCSRF __REG(0x40600118) /* UDC Control/Status register - Endpoint F */ +#define UDCCSRG __REG(0x4060011C) /* UDC Control/Status register - Endpoint G */ +#define UDCCSRH __REG(0x40600120) /* UDC Control/Status register - Endpoint H */ +#define UDCCSRI __REG(0x40600124) /* UDC Control/Status register - Endpoint I */ +#define UDCCSRJ __REG(0x40600128) /* UDC Control/Status register - Endpoint J */ +#define UDCCSRK __REG(0x4060012C) /* UDC Control/Status register - Endpoint K */ +#define UDCCSRL __REG(0x40600130) /* UDC Control/Status register - Endpoint L */ +#define UDCCSRM __REG(0x40600134) /* UDC Control/Status register - Endpoint M */ +#define UDCCSRN __REG(0x40600138) /* UDC Control/Status register - Endpoint N */ +#define UDCCSRP __REG(0x4060013C) /* UDC Control/Status register - Endpoint P */ +#define UDCCSRQ __REG(0x40600140) /* UDC Control/Status register - Endpoint Q */ +#define UDCCSRR __REG(0x40600144) /* UDC Control/Status register - Endpoint R */ +#define UDCCSRS __REG(0x40600148) /* UDC Control/Status register - Endpoint S */ +#define UDCCSRT __REG(0x4060014C) /* UDC Control/Status register - Endpoint T */ +#define UDCCSRU __REG(0x40600150) /* UDC Control/Status register - Endpoint U */ +#define UDCCSRV __REG(0x40600154) /* UDC Control/Status register - Endpoint V */ +#define UDCCSRW __REG(0x40600158) /* UDC Control/Status register - Endpoint W */ +#define UDCCSRX __REG(0x4060015C) /* UDC Control/Status register - Endpoint X */ + +#define UDCCSR_DPE (1 << 9) /* Data Packet Error */ +#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */ +#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */ +#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */ +#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */ +#define UDCCSR_FST (1 << 5) /* Force STALL */ +#define UDCCSR_SST (1 << 4) /* Sent STALL */ +#define UDCCSR_DME (1 << 3) /* DMA Enable */ +#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */ +#define UDCCSR_PC (1 << 1) /* Packet Complete */ +#define UDCCSR_FS (1 << 0) /* FIFO needs service */ + +#define UDCBCN(x) __REG2(0x40600200, (x)<<2) +#define UDCBCR0 __REG(0x40600200) /* Byte Count Register - EP0 */ +#define UDCBCRA __REG(0x40600204) /* Byte Count Register - EPA */ +#define UDCBCRB __REG(0x40600208) /* Byte Count Register - EPB */ +#define UDCBCRC __REG(0x4060020C) /* Byte Count Register - EPC */ +#define UDCBCRD __REG(0x40600210) /* Byte Count Register - EPD */ +#define UDCBCRE __REG(0x40600214) /* Byte Count Register - EPE */ +#define UDCBCRF __REG(0x40600218) /* Byte Count Register - EPF */ +#define UDCBCRG __REG(0x4060021C) /* Byte Count Register - EPG */ +#define UDCBCRH __REG(0x40600220) /* Byte Count Register - EPH */ +#define UDCBCRI __REG(0x40600224) /* Byte Count Register - EPI */ +#define UDCBCRJ __REG(0x40600228) /* Byte Count Register - EPJ */ +#define UDCBCRK __REG(0x4060022C) /* Byte Count Register - EPK */ +#define UDCBCRL __REG(0x40600230) /* Byte Count Register - EPL */ +#define UDCBCRM __REG(0x40600234) /* Byte Count Register - EPM */ +#define UDCBCRN __REG(0x40600238) /* Byte Count Register - EPN */ +#define UDCBCRP __REG(0x4060023C) /* Byte Count Register - EPP */ +#define UDCBCRQ __REG(0x40600240) /* Byte Count Register - EPQ */ +#define UDCBCRR __REG(0x40600244) /* Byte Count Register - EPR */ +#define UDCBCRS __REG(0x40600248) /* Byte Count Register - EPS */ +#define UDCBCRT __REG(0x4060024C) /* Byte Count Register - EPT */ +#define UDCBCRU __REG(0x40600250) /* Byte Count Register - EPU */ +#define UDCBCRV __REG(0x40600254) /* Byte Count Register - EPV */ +#define UDCBCRW __REG(0x40600258) /* Byte Count Register - EPW */ +#define UDCBCRX __REG(0x4060025C) /* Byte Count Register - EPX */ + +#define UDCDN(x) __REG2(0x40600300, (x)<<2) +#define PHYS_UDCDN(x) (0x40600300 + ((x)<<2)) +#define PUDCDN(x) (volatile u32 *)(io_p2v(PHYS_UDCDN((x)))) +#define UDCDR0 __REG(0x40600300) /* Data Register - EP0 */ +#define UDCDRA __REG(0x40600304) /* Data Register - EPA */ +#define UDCDRB __REG(0x40600308) /* Data Register - EPB */ +#define UDCDRC __REG(0x4060030C) /* Data Register - EPC */ +#define UDCDRD __REG(0x40600310) /* Data Register - EPD */ +#define UDCDRE __REG(0x40600314) /* Data Register - EPE */ +#define UDCDRF __REG(0x40600318) /* Data Register - EPF */ +#define UDCDRG __REG(0x4060031C) /* Data Register - EPG */ +#define UDCDRH __REG(0x40600320) /* Data Register - EPH */ +#define UDCDRI __REG(0x40600324) /* Data Register - EPI */ +#define UDCDRJ __REG(0x40600328) /* Data Register - EPJ */ +#define UDCDRK __REG(0x4060032C) /* Data Register - EPK */ +#define UDCDRL __REG(0x40600330) /* Data Register - EPL */ +#define UDCDRM __REG(0x40600334) /* Data Register - EPM */ +#define UDCDRN __REG(0x40600338) /* Data Register - EPN */ +#define UDCDRP __REG(0x4060033C) /* Data Register - EPP */ +#define UDCDRQ __REG(0x40600340) /* Data Register - EPQ */ +#define UDCDRR __REG(0x40600344) /* Data Register - EPR */ +#define UDCDRS __REG(0x40600348) /* Data Register - EPS */ +#define UDCDRT __REG(0x4060034C) /* Data Register - EPT */ +#define UDCDRU __REG(0x40600350) /* Data Register - EPU */ +#define UDCDRV __REG(0x40600354) /* Data Register - EPV */ +#define UDCDRW __REG(0x40600358) /* Data Register - EPW */ +#define UDCDRX __REG(0x4060035C) /* Data Register - EPX */ + +#define UDCCN(x) __REG2(0x40600400, (x)<<2) +#define UDCCRA __REG(0x40600404) /* Configuration register EPA */ +#define UDCCRB __REG(0x40600408) /* Configuration register EPB */ +#define UDCCRC __REG(0x4060040C) /* Configuration register EPC */ +#define UDCCRD __REG(0x40600410) /* Configuration register EPD */ +#define UDCCRE __REG(0x40600414) /* Configuration register EPE */ +#define UDCCRF __REG(0x40600418) /* Configuration register EPF */ +#define UDCCRG __REG(0x4060041C) /* Configuration register EPG */ +#define UDCCRH __REG(0x40600420) /* Configuration register EPH */ +#define UDCCRI __REG(0x40600424) /* Configuration register EPI */ +#define UDCCRJ __REG(0x40600428) /* Configuration register EPJ */ +#define UDCCRK __REG(0x4060042C) /* Configuration register EPK */ +#define UDCCRL __REG(0x40600430) /* Configuration register EPL */ +#define UDCCRM __REG(0x40600434) /* Configuration register EPM */ +#define UDCCRN __REG(0x40600438) /* Configuration register EPN */ +#define UDCCRP __REG(0x4060043C) /* Configuration register EPP */ +#define UDCCRQ __REG(0x40600440) /* Configuration register EPQ */ +#define UDCCRR __REG(0x40600444) /* Configuration register EPR */ +#define UDCCRS __REG(0x40600448) /* Configuration register EPS */ +#define UDCCRT __REG(0x4060044C) /* Configuration register EPT */ +#define UDCCRU __REG(0x40600450) /* Configuration register EPU */ +#define UDCCRV __REG(0x40600454) /* Configuration register EPV */ +#define UDCCRW __REG(0x40600458) /* Configuration register EPW */ +#define UDCCRX __REG(0x4060045C) /* Configuration register EPX */ + +#define UDCCONR_CN (0x03 << 25) /* Configuration Number */ +#define UDCCONR_CN_S (25) +#define UDCCONR_IN (0x07 << 22) /* Interface Number */ +#define UDCCONR_IN_S (22) +#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */ +#define UDCCONR_AISN_S (19) +#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */ +#define UDCCONR_EN_S (15) +#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */ +#define UDCCONR_ET_S (13) +#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */ +#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */ +#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */ +#define UDCCONR_ET_NU (0x00 << 13) /* Not used */ +#define UDCCONR_ED (1 << 12) /* Endpoint Direction */ +#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */ +#define UDCCONR_MPS_S (2) +#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */ +#define UDCCONR_EE (1 << 0) /* Endpoint Enable */ + + +#define UDC_INT_FIFOERROR (0x2) +#define UDC_INT_PACKETCMP (0x1) + +#define UDC_FNR_MASK (0x7ff) + +#define UDCCSR_WR_MASK (UDCCSR_DME|UDCCSR_FST) +#define UDC_BCR_MASK (0x3ff) + +#endif -- cgit v1.2.3 From bedd78ca786c1d18c2a2785c7e40593dc9c9870f Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 12:31:29 +0100 Subject: [RTC] remove old ARM rtc library code Now that all drivers using it are gone, remove the old ARM RTC library. Acked-by: Alessandro Zummo Signed-off-by: Russell King --- include/asm-arm/rtc.h | 43 ------------------------------------------- 1 file changed, 43 deletions(-) delete mode 100644 include/asm-arm/rtc.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/rtc.h b/include/asm-arm/rtc.h deleted file mode 100644 index 1a5c9232a91..00000000000 --- a/include/asm-arm/rtc.h +++ /dev/null @@ -1,43 +0,0 @@ -/* - * linux/include/asm-arm/rtc.h - * - * Copyright (C) 2003 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#ifndef ASMARM_RTC_H -#define ASMARM_RTC_H - -struct module; - -struct rtc_ops { - struct module *owner; - int (*open)(void); - void (*release)(void); - int (*ioctl)(unsigned int, unsigned long); - - int (*read_time)(struct rtc_time *); - int (*set_time)(struct rtc_time *); - int (*read_alarm)(struct rtc_wkalrm *); - int (*set_alarm)(struct rtc_wkalrm *); - int (*proc)(char *buf); -}; - -void rtc_next_alarm_time(struct rtc_time *, struct rtc_time *, struct rtc_time *); -void rtc_update(unsigned long, unsigned long); -int register_rtc(struct rtc_ops *); -void unregister_rtc(struct rtc_ops *); - -static inline int rtc_periodic_alarm(struct rtc_time *tm) -{ - return (tm->tm_year == -1) || - ((unsigned)tm->tm_mon >= 12) || - ((unsigned)(tm->tm_mday - 1) >= 31) || - ((unsigned)tm->tm_hour > 23) || - ((unsigned)tm->tm_min > 59) || - ((unsigned)tm->tm_sec > 59); -} - -#endif -- cgit v1.2.3 From 8ff7f2a46bd8831e1f1f2a694ec13921720180b7 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Thu, 21 Feb 2008 16:30:10 +0100 Subject: There is no need to have BOOT_PARAMS_SIZE known outside of atags.c MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit atags.c was the only user of KEXEC_BOOT_PARAMS_SIZE and kexec.h was only included to get that definition. Signed-off-by: Uwe Kleine-König Acked-by: Uli Luckas --- include/asm-arm/kexec.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/kexec.h b/include/asm-arm/kexec.h index 47fe34d692d..c8986bb99ed 100644 --- a/include/asm-arm/kexec.h +++ b/include/asm-arm/kexec.h @@ -14,8 +14,6 @@ #define KEXEC_ARCH KEXEC_ARCH_ARM -#define KEXEC_BOOT_PARAMS_SIZE 1536 - #define KEXEC_ARM_ATAGS_OFFSET 0x1000 #define KEXEC_ARM_ZIMAGE_OFFSET 0x8000 -- cgit v1.2.3 From a4831fbe096a6f4f691fd71b041ce27add54088e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Wed, 21 May 2008 10:17:07 +0200 Subject: ns9xxx: fix assembler version of __REG2 to be consistent with the C version MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit It's not very critical because __REG2 isn't used in assembler code currently. Additionally some white space noise is fixed. Signed-off-by: Uwe Kleine-König --- include/asm-arm/arch-ns9xxx/hardware.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-ns9xxx/hardware.h b/include/asm-arm/arch-ns9xxx/hardware.h index 0b7b34603f1..0dca11ce21f 100644 --- a/include/asm-arm/arch-ns9xxx/hardware.h +++ b/include/asm-arm/arch-ns9xxx/hardware.h @@ -66,13 +66,13 @@ __REGGET(var, reg ## _ ## field) / __REGSHIFT(reg ## _ ## field) # define REGGETIM_IDX(var, reg, field, idx) \ - __REGGET(var, reg ## _ ## field((idx))) / \ + __REGGET(var, reg ## _ ## field((idx))) / \ __REGSHIFT(reg ## _ ## field((idx))) #else # define __REG(x) io_p2v(x) -# define __REG2(x, y) io_p2v((x) + (y)) +# define __REG2(x, y) io_p2v((x) + 4 * (y)) #endif -- cgit v1.2.3 From e0773410247f1e5fc6f7c52a4c5f3c6c9873d527 Mon Sep 17 00:00:00 2001 From: Abhishek Sagar Date: Sat, 31 May 2008 14:24:02 +0530 Subject: ftrace: export kretprobe_trampoline for function tracer Follow suit from kprobe implementations on other archs and make kretprobe_trampoline non-static. Ftrace implmentation (more specifically, kernel/trace/trace.c) requires access to it (see-> http://kerneltrap.org/mailarchive/linux-kernel/2008/5/27/1955234). Signed-off-by: Abhishek Sagar Signed-off-by: Ingo Molnar --- include/asm-arm/kprobes.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/kprobes.h b/include/asm-arm/kprobes.h index c042194d3ab..b1a37876942 100644 --- a/include/asm-arm/kprobes.h +++ b/include/asm-arm/kprobes.h @@ -59,6 +59,7 @@ struct kprobe_ctlblk { }; void arch_remove_kprobe(struct kprobe *); +void kretprobe_trampoline(void); int kprobe_trap_handler(struct pt_regs *regs, unsigned int instr); int kprobe_fault_handler(struct pt_regs *regs, unsigned int fsr); -- cgit v1.2.3 From 1a7e612fa5ea0311232bd5418a40ec7280557789 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 31 May 2008 16:18:11 +0100 Subject: [ARM] 5074/1: fix warning: missing terminating ' character Signed-off-by: Dmitry Baryshkov Acked-by: Richard Purdie Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa27x-udc.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxa27x-udc.h b/include/asm-arm/arch-pxa/pxa27x-udc.h index 9cf0b1f8811..2d4e9cd3a5e 100644 --- a/include/asm-arm/arch-pxa/pxa27x-udc.h +++ b/include/asm-arm/arch-pxa/pxa27x-udc.h @@ -2,7 +2,7 @@ #define _ASM_ARCH_PXA27X_UDC_H #ifdef _ASM_ARCH_PXA25X_UDC_H -#error You can't include both PXA25x and PXA27x UDC support +#error You cannot include both PXA25x and PXA27x UDC support #endif #define UDCCR __REG(0x40600000) /* UDC Control Register */ -- cgit v1.2.3 From ca0a789ab9c83d8fdf28f5c2700b316cd5dec2f0 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Sat, 24 May 2008 17:47:04 +0100 Subject: [ARM] 5057/1: [AT91] Calao Systems - board files MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add support for three AT91-based boards available from Calao Systems: USB_A9260, USB_A9263 and QIL_A9260. Signed-off-by: Grégory Hermant Signed-off-by: Andrew Victor Signed-off-by: Russell King --- include/asm-arm/arch-at91/timex.h | 17 ++++++++++++++++- 1 file changed, 16 insertions(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-at91/timex.h b/include/asm-arm/arch-at91/timex.h index f1933b0fa43..6e084eb839d 100644 --- a/include/asm-arm/arch-at91/timex.h +++ b/include/asm-arm/arch-at91/timex.h @@ -27,14 +27,29 @@ #define CLOCK_TICK_RATE (AT91_SLOW_CLOCK) -#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9261) +#elif defined(CONFIG_ARCH_AT91SAM9260) + +#if defined(CONFIG_MACH_USB_A9260) || defined(CONFIG_MACH_QIL_A9260) +#define AT91SAM9_MASTER_CLOCK 90000000 +#else +#define AT91SAM9_MASTER_CLOCK 99300000 +#endif + +#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) + +#elif defined(CONFIG_ARCH_AT91SAM9261) #define AT91SAM9_MASTER_CLOCK 99300000 #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) #elif defined(CONFIG_ARCH_AT91SAM9263) +#if defined(CONFIG_MACH_USB_A9263) +#define AT91SAM9_MASTER_CLOCK 90000000 +#else #define AT91SAM9_MASTER_CLOCK 99959500 +#endif + #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) #elif defined(CONFIG_ARCH_AT91SAM9RL) -- cgit v1.2.3 From 53d7168026a440c4cba25468a3d926ddd7ab030a Mon Sep 17 00:00:00 2001 From: Stelian Pop Date: Sat, 5 Apr 2008 21:14:03 +0100 Subject: [ARM] 4933/1: AT91CAP9 UDPHS driver: generic AT91 parts. This is patch 1 of 2 adding support for the USB High Speed Device Port on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP as the AVR32 and the AT91SAM9RL. This patch makes the generic AT91 adaptations, mainly dealing with the addition of the UDPHS UTMI clock. Signed-off-by: Stelian Pop Acked-by: Haavard Skinnemoen Acked-by: Andrew Victor Signed-off-by: Russell King --- include/asm-arm/arch-at91/at91_pmc.h | 7 ++++++- include/asm-arm/arch-at91/board.h | 4 ++++ 2 files changed, 10 insertions(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-at91/at91_pmc.h b/include/asm-arm/arch-at91/at91_pmc.h index c2b13c28015..2001e81f226 100644 --- a/include/asm-arm/arch-at91/at91_pmc.h +++ b/include/asm-arm/arch-at91/at91_pmc.h @@ -39,10 +39,14 @@ #define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */ #define AT91_CKGR_UCKR (AT91_PMC + 0x1C) /* UTMI Clock Register [SAM9RL, CAP9] */ +#define AT91_PMC_UPLLEN (1 << 16) /* UTMI PLL Enable */ +#define AT91_PMC_UPLLCOUNT (0xf << 20) /* UTMI PLL Start-up Time */ +#define AT91_PMC_BIASEN (1 << 24) /* UTMI BIAS Enable */ +#define AT91_PMC_BIASCOUNT (0xf << 28) /* UTMI PLL Start-up Time */ #define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register [not on SAM9RL] */ #define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */ -#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [AT91SAM926x only] */ +#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [SAM9x, CAP9] */ #define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */ #define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */ @@ -97,6 +101,7 @@ #define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */ #define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */ #define AT91_PMC_MCKRDY (1 << 3) /* Master Clock */ +#define AT91_PMC_LOCKU (1 << 6) /* UPLL Lock [AT91CAP9 only] */ #define AT91_PMC_PCK0RDY (1 << 8) /* Programmable Clock 0 */ #define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */ #define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */ diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h index dc189f01c5b..1f247028686 100644 --- a/include/asm-arm/arch-at91/board.h +++ b/include/asm-arm/arch-at91/board.h @@ -36,6 +36,7 @@ #include #include #include +#include /* USB Device */ struct at91_udc_data { @@ -45,6 +46,9 @@ struct at91_udc_data { }; extern void __init at91_add_device_udc(struct at91_udc_data *data); + /* USB High Speed Device */ +extern void __init at91_add_device_usba(struct usba_platform_data *data); + /* Compact Flash */ struct at91_cf_data { u8 irq_pin; /* I/O IRQ */ -- cgit v1.2.3 From 7c8cf66529ebf95f1a5f34d1b69504d442b42630 Mon Sep 17 00:00:00 2001 From: Stelian Pop Date: Sat, 5 Apr 2008 21:15:25 +0100 Subject: [ARM] 4934/1: AT91CAP9 UDPHS driver: board and cpu integration. This is patch 2 of 2 adding support for the USB High Speed Device Port on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP as the AVR32 and the AT91SAM9RL. This patch declares the UDPHS ressources in the at91cap9 (cpu and adk board) files, wires up the atmel_usba_udc driver to them, and activates the driver in the defconfig. Signed-off-by: Stelian Pop Acked-by: Haavard Skinnemoen Acked-by: Andrew Victor Signed-off-by: Russell King --- include/asm-arm/arch-at91/at91cap9.h | 2 +- include/asm-arm/arch-at91/at91cap9_matrix.h | 5 +++++ 2 files changed, 6 insertions(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-at91/at91cap9.h b/include/asm-arm/arch-at91/at91cap9.h index bac83adb505..6f14d9053ac 100644 --- a/include/asm-arm/arch-at91/at91cap9.h +++ b/include/asm-arm/arch-at91/at91cap9.h @@ -118,7 +118,7 @@ #define AT91CAP9_ROM_SIZE (32 * SZ_1K) /* Internal ROM size (32Kb) */ #define AT91CAP9_LCDC_BASE 0x00500000 /* LCD Controller */ -#define AT91CAP9_UDPHS_BASE 0x00600000 /* USB High Speed Device Port */ +#define AT91CAP9_UDPHS_FIFO 0x00600000 /* USB High Speed Device Port */ #define AT91CAP9_UHP_BASE 0x00700000 /* USB Host controller */ #define CONFIG_DRAM_BASE AT91_CHIPSELECT_6 diff --git a/include/asm-arm/arch-at91/at91cap9_matrix.h b/include/asm-arm/arch-at91/at91cap9_matrix.h index a641686b6c3..ddbd4873c84 100644 --- a/include/asm-arm/arch-at91/at91cap9_matrix.h +++ b/include/asm-arm/arch-at91/at91cap9_matrix.h @@ -106,6 +106,11 @@ #define AT91_MPBS0_SFR (AT91_MATRIX + 0x114) /* MPBlock Slave 0 Special Function Register */ #define AT91_MPBS1_SFR (AT91_MATRIX + 0x11C) /* MPBlock Slave 1 Special Function Register */ +#define AT91_MATRIX_UDPHS (AT91_MATRIX + 0x118) /* USBHS Special Function Register [AT91CAP9 only] */ +#define AT91_MATRIX_SELECT_UDPHS (0 << 31) /* select High Speed UDP */ +#define AT91_MATRIX_SELECT_UDP (1 << 31) /* select standard UDP */ +#define AT91_MATRIX_UDPHS_BYPASS_LOCK (1 << 30) /* bypass lock bit */ + #define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x120) /* EBI Chip Select Assignment Register */ #define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ #define AT91_MATRIX_EBI_CS1A_SMC (0 << 1) -- cgit v1.2.3 From ba45ca435060614e595a107ac323a36b52619d7d Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 8 Apr 2008 13:59:18 +0100 Subject: [ARM] 4940/1: AT91: UDPHS driver: SAM9RL board and cpu integration. Adds support for the USB High Speed Device Port on the AT91SAM9RL system on chip. The AT91SAM9RL uses the same UDPHS IP as the AVR32 and the AT91CAP9 (atmel_usba_udc driver). Signed-off-by: Nicolas Ferre Acked-by: Andrew Victor Signed-off-by: Russell King --- include/asm-arm/arch-at91/at91sam9rl.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-at91/at91sam9rl.h b/include/asm-arm/arch-at91/at91sam9rl.h index 16d2832f6c0..622e56f81d4 100644 --- a/include/asm-arm/arch-at91/at91sam9rl.h +++ b/include/asm-arm/arch-at91/at91sam9rl.h @@ -110,6 +110,6 @@ #define AT91SAM9RL_ROM_SIZE (2 * SZ_16K) /* Internal ROM size (32Kb) */ #define AT91SAM9RL_LCDC_BASE 0x00500000 /* LCD Controller */ -#define AT91SAM9RL_UDPHS_BASE 0x00600000 /* USB Device HS controller */ +#define AT91SAM9RL_UDPHS_FIFO 0x00600000 /* USB Device HS controller */ #endif -- cgit v1.2.3 From 0b0a9df6038752674e54e333cd247c877d29aab8 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 18 May 2008 14:59:36 +0100 Subject: [ARM] pxa: separate out power manager and clock registers The power manager and core clock registers aren't present in PXA3 CPUs. Move them out of pxa-regs.h into pxa2xx-regs.h, and include pxa2xx-regs.h where necessary. Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa-regs.h | 158 +------------------------------- include/asm-arm/arch-pxa/pxa2xx-regs.h | 162 +++++++++++++++++++++++++++++++++ include/asm-arm/arch-pxa/system.h | 1 + 3 files changed, 165 insertions(+), 156 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h index 68d74287730..dce9308626b 100644 --- a/include/asm-arm/arch-pxa/pxa-regs.h +++ b/include/asm-arm/arch-pxa/pxa-regs.h @@ -825,120 +825,9 @@ #endif /* - * Power Manager + * Power Manager - see pxa2xx-regs.h */ -#define PMCR __REG(0x40F00000) /* Power Manager Control Register */ -#define PSSR __REG(0x40F00004) /* Power Manager Sleep Status Register */ -#define PSPR __REG(0x40F00008) /* Power Manager Scratch Pad Register */ -#define PWER __REG(0x40F0000C) /* Power Manager Wake-up Enable Register */ -#define PRER __REG(0x40F00010) /* Power Manager GPIO Rising-Edge Detect Enable Register */ -#define PFER __REG(0x40F00014) /* Power Manager GPIO Falling-Edge Detect Enable Register */ -#define PEDR __REG(0x40F00018) /* Power Manager GPIO Edge Detect Status Register */ -#define PCFR __REG(0x40F0001C) /* Power Manager General Configuration Register */ -#define PGSR0 __REG(0x40F00020) /* Power Manager GPIO Sleep State Register for GP[31-0] */ -#define PGSR1 __REG(0x40F00024) /* Power Manager GPIO Sleep State Register for GP[63-32] */ -#define PGSR2 __REG(0x40F00028) /* Power Manager GPIO Sleep State Register for GP[84-64] */ -#define PGSR3 __REG(0x40F0002C) /* Power Manager GPIO Sleep State Register for GP[118-96] */ -#define RCSR __REG(0x40F00030) /* Reset Controller Status Register */ - -#define PSLR __REG(0x40F00034) /* Power Manager Sleep Config Register */ -#define PSTR __REG(0x40F00038) /*Power Manager Standby Config Register */ -#define PSNR __REG(0x40F0003C) /*Power Manager Sense Config Register */ -#define PVCR __REG(0x40F00040) /*Power Manager VoltageControl Register */ -#define PKWR __REG(0x40F00050) /* Power Manager KB Wake-up Enable Reg */ -#define PKSR __REG(0x40F00054) /* Power Manager KB Level-Detect Register */ -#define PCMD(x) __REG2(0x40F00080, (x)<<2) -#define PCMD0 __REG(0x40F00080 + 0 * 4) -#define PCMD1 __REG(0x40F00080 + 1 * 4) -#define PCMD2 __REG(0x40F00080 + 2 * 4) -#define PCMD3 __REG(0x40F00080 + 3 * 4) -#define PCMD4 __REG(0x40F00080 + 4 * 4) -#define PCMD5 __REG(0x40F00080 + 5 * 4) -#define PCMD6 __REG(0x40F00080 + 6 * 4) -#define PCMD7 __REG(0x40F00080 + 7 * 4) -#define PCMD8 __REG(0x40F00080 + 8 * 4) -#define PCMD9 __REG(0x40F00080 + 9 * 4) -#define PCMD10 __REG(0x40F00080 + 10 * 4) -#define PCMD11 __REG(0x40F00080 + 11 * 4) -#define PCMD12 __REG(0x40F00080 + 12 * 4) -#define PCMD13 __REG(0x40F00080 + 13 * 4) -#define PCMD14 __REG(0x40F00080 + 14 * 4) -#define PCMD15 __REG(0x40F00080 + 15 * 4) -#define PCMD16 __REG(0x40F00080 + 16 * 4) -#define PCMD17 __REG(0x40F00080 + 17 * 4) -#define PCMD18 __REG(0x40F00080 + 18 * 4) -#define PCMD19 __REG(0x40F00080 + 19 * 4) -#define PCMD20 __REG(0x40F00080 + 20 * 4) -#define PCMD21 __REG(0x40F00080 + 21 * 4) -#define PCMD22 __REG(0x40F00080 + 22 * 4) -#define PCMD23 __REG(0x40F00080 + 23 * 4) -#define PCMD24 __REG(0x40F00080 + 24 * 4) -#define PCMD25 __REG(0x40F00080 + 25 * 4) -#define PCMD26 __REG(0x40F00080 + 26 * 4) -#define PCMD27 __REG(0x40F00080 + 27 * 4) -#define PCMD28 __REG(0x40F00080 + 28 * 4) -#define PCMD29 __REG(0x40F00080 + 29 * 4) -#define PCMD30 __REG(0x40F00080 + 30 * 4) -#define PCMD31 __REG(0x40F00080 + 31 * 4) - -#define PCMD_MBC (1<<12) -#define PCMD_DCE (1<<11) -#define PCMD_LC (1<<10) -/* FIXME: PCMD_SQC need be checked. */ -#define PCMD_SQC (3<<8) /* currently only bit 8 is changeable, - bit 9 should be 0 all day. */ -#define PVCR_VCSA (0x1<<14) -#define PVCR_CommandDelay (0xf80) -#define PCFR_PI2C_EN (0x1 << 6) - -#define PSSR_OTGPH (1 << 6) /* OTG Peripheral control Hold */ -#define PSSR_RDH (1 << 5) /* Read Disable Hold */ -#define PSSR_PH (1 << 4) /* Peripheral Control Hold */ -#define PSSR_STS (1 << 3) /* Standby Mode Status */ -#define PSSR_VFS (1 << 2) /* VDD Fault Status */ -#define PSSR_BFS (1 << 1) /* Battery Fault Status */ -#define PSSR_SSS (1 << 0) /* Software Sleep Status */ - -#define PSLR_SL_ROD (1 << 20) /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */ - -#define PCFR_RO (1 << 15) /* RDH Override */ -#define PCFR_PO (1 << 14) /* PH Override */ -#define PCFR_GPROD (1 << 12) /* GPIO nRESET_OUT Disable */ -#define PCFR_L1_EN (1 << 11) /* Sleep Mode L1 converter Enable */ -#define PCFR_FVC (1 << 10) /* Frequency/Voltage Change */ -#define PCFR_DC_EN (1 << 7) /* Sleep/deep-sleep DC-DC Converter Enable */ -#define PCFR_PI2CEN (1 << 6) /* Enable PI2C controller */ -#define PCFR_GPR_EN (1 << 4) /* nRESET_GPIO Pin Enable */ -#define PCFR_DS (1 << 3) /* Deep Sleep Mode */ -#define PCFR_FS (1 << 2) /* Float Static Chip Selects */ -#define PCFR_FP (1 << 1) /* Float PCMCIA controls */ -#define PCFR_OPDE (1 << 0) /* 3.6864 MHz oscillator power-down enable */ - -#define RCSR_GPR (1 << 3) /* GPIO Reset */ -#define RCSR_SMR (1 << 2) /* Sleep Mode */ -#define RCSR_WDR (1 << 1) /* Watchdog Reset */ -#define RCSR_HWR (1 << 0) /* Hardware Reset */ - -#define PWER_GPIO(Nb) (1 << Nb) /* GPIO [0..15] wake-up enable */ -#define PWER_GPIO0 PWER_GPIO (0) /* GPIO [0] wake-up enable */ -#define PWER_GPIO1 PWER_GPIO (1) /* GPIO [1] wake-up enable */ -#define PWER_GPIO2 PWER_GPIO (2) /* GPIO [2] wake-up enable */ -#define PWER_GPIO3 PWER_GPIO (3) /* GPIO [3] wake-up enable */ -#define PWER_GPIO4 PWER_GPIO (4) /* GPIO [4] wake-up enable */ -#define PWER_GPIO5 PWER_GPIO (5) /* GPIO [5] wake-up enable */ -#define PWER_GPIO6 PWER_GPIO (6) /* GPIO [6] wake-up enable */ -#define PWER_GPIO7 PWER_GPIO (7) /* GPIO [7] wake-up enable */ -#define PWER_GPIO8 PWER_GPIO (8) /* GPIO [8] wake-up enable */ -#define PWER_GPIO9 PWER_GPIO (9) /* GPIO [9] wake-up enable */ -#define PWER_GPIO10 PWER_GPIO (10) /* GPIO [10] wake-up enable */ -#define PWER_GPIO11 PWER_GPIO (11) /* GPIO [11] wake-up enable */ -#define PWER_GPIO12 PWER_GPIO (12) /* GPIO [12] wake-up enable */ -#define PWER_GPIO13 PWER_GPIO (13) /* GPIO [13] wake-up enable */ -#define PWER_GPIO14 PWER_GPIO (14) /* GPIO [14] wake-up enable */ -#define PWER_GPIO15 PWER_GPIO (15) /* GPIO [15] wake-up enable */ -#define PWER_RTC 0x80000000 /* RTC alarm wake-up enable */ - /* * SSP Serial Port Registers - see include/asm-arm/arch-pxa/regs-ssp.h */ @@ -948,52 +837,9 @@ */ /* - * Core Clock + * Core Clock - see include/asm-arm/arch-pxa/pxa2xx-regs.h */ -#define CCCR __REG(0x41300000) /* Core Clock Configuration Register */ -#define CKEN __REG(0x41300004) /* Clock Enable Register */ -#define OSCC __REG(0x41300008) /* Oscillator Configuration Register */ -#define CCSR __REG(0x4130000C) /* Core Clock Status Register */ - -#define CCCR_N_MASK 0x0380 /* Run Mode Frequency to Turbo Mode Frequency Multiplier */ -#define CCCR_M_MASK 0x0060 /* Memory Frequency to Run Mode Frequency Multiplier */ -#define CCCR_L_MASK 0x001f /* Crystal Frequency to Memory Frequency Multiplier */ - -#define CKEN_AC97CONF (31) /* AC97 Controller Configuration */ -#define CKEN_CAMERA (24) /* Camera Interface Clock Enable */ -#define CKEN_SSP1 (23) /* SSP1 Unit Clock Enable */ -#define CKEN_MEMC (22) /* Memory Controller Clock Enable */ -#define CKEN_MEMSTK (21) /* Memory Stick Host Controller */ -#define CKEN_IM (20) /* Internal Memory Clock Enable */ -#define CKEN_KEYPAD (19) /* Keypad Interface Clock Enable */ -#define CKEN_USIM (18) /* USIM Unit Clock Enable */ -#define CKEN_MSL (17) /* MSL Unit Clock Enable */ -#define CKEN_LCD (16) /* LCD Unit Clock Enable */ -#define CKEN_PWRI2C (15) /* PWR I2C Unit Clock Enable */ -#define CKEN_I2C (14) /* I2C Unit Clock Enable */ -#define CKEN_FICP (13) /* FICP Unit Clock Enable */ -#define CKEN_MMC (12) /* MMC Unit Clock Enable */ -#define CKEN_USB (11) /* USB Unit Clock Enable */ -#define CKEN_ASSP (10) /* ASSP (SSP3) Clock Enable */ -#define CKEN_USBHOST (10) /* USB Host Unit Clock Enable */ -#define CKEN_OSTIMER (9) /* OS Timer Unit Clock Enable */ -#define CKEN_NSSP (9) /* NSSP (SSP2) Clock Enable */ -#define CKEN_I2S (8) /* I2S Unit Clock Enable */ -#define CKEN_BTUART (7) /* BTUART Unit Clock Enable */ -#define CKEN_FFUART (6) /* FFUART Unit Clock Enable */ -#define CKEN_STUART (5) /* STUART Unit Clock Enable */ -#define CKEN_HWUART (4) /* HWUART Unit Clock Enable */ -#define CKEN_SSP3 (4) /* SSP3 Unit Clock Enable */ -#define CKEN_SSP (3) /* SSP Unit Clock Enable */ -#define CKEN_SSP2 (3) /* SSP2 Unit Clock Enable */ -#define CKEN_AC97 (2) /* AC97 Unit Clock Enable */ -#define CKEN_PWM1 (1) /* PWM1 Clock Enable */ -#define CKEN_PWM0 (0) /* PWM0 Clock Enable */ - -#define OSCC_OON (1 << 1) /* 32.768kHz OON (write-once only bit) */ -#define OSCC_OOK (1 << 0) /* 32.768kHz OOK (read-only bit) */ - #ifdef CONFIG_PXA27x /* Camera Interface */ diff --git a/include/asm-arm/arch-pxa/pxa2xx-regs.h b/include/asm-arm/arch-pxa/pxa2xx-regs.h index 9553b54fa5b..73e0a329cf7 100644 --- a/include/asm-arm/arch-pxa/pxa2xx-regs.h +++ b/include/asm-arm/arch-pxa/pxa2xx-regs.h @@ -81,4 +81,166 @@ #endif + +/* + * Power Manager + */ + +#define PMCR __REG(0x40F00000) /* Power Manager Control Register */ +#define PSSR __REG(0x40F00004) /* Power Manager Sleep Status Register */ +#define PSPR __REG(0x40F00008) /* Power Manager Scratch Pad Register */ +#define PWER __REG(0x40F0000C) /* Power Manager Wake-up Enable Register */ +#define PRER __REG(0x40F00010) /* Power Manager GPIO Rising-Edge Detect Enable Register */ +#define PFER __REG(0x40F00014) /* Power Manager GPIO Falling-Edge Detect Enable Register */ +#define PEDR __REG(0x40F00018) /* Power Manager GPIO Edge Detect Status Register */ +#define PCFR __REG(0x40F0001C) /* Power Manager General Configuration Register */ +#define PGSR0 __REG(0x40F00020) /* Power Manager GPIO Sleep State Register for GP[31-0] */ +#define PGSR1 __REG(0x40F00024) /* Power Manager GPIO Sleep State Register for GP[63-32] */ +#define PGSR2 __REG(0x40F00028) /* Power Manager GPIO Sleep State Register for GP[84-64] */ +#define PGSR3 __REG(0x40F0002C) /* Power Manager GPIO Sleep State Register for GP[118-96] */ +#define RCSR __REG(0x40F00030) /* Reset Controller Status Register */ + +#define PSLR __REG(0x40F00034) /* Power Manager Sleep Config Register */ +#define PSTR __REG(0x40F00038) /* Power Manager Standby Config Register */ +#define PSNR __REG(0x40F0003C) /* Power Manager Sense Config Register */ +#define PVCR __REG(0x40F00040) /* Power Manager VoltageControl Register */ +#define PKWR __REG(0x40F00050) /* Power Manager KB Wake-up Enable Reg */ +#define PKSR __REG(0x40F00054) /* Power Manager KB Level-Detect Register */ +#define PCMD(x) __REG2(0x40F00080, (x)<<2) +#define PCMD0 __REG(0x40F00080 + 0 * 4) +#define PCMD1 __REG(0x40F00080 + 1 * 4) +#define PCMD2 __REG(0x40F00080 + 2 * 4) +#define PCMD3 __REG(0x40F00080 + 3 * 4) +#define PCMD4 __REG(0x40F00080 + 4 * 4) +#define PCMD5 __REG(0x40F00080 + 5 * 4) +#define PCMD6 __REG(0x40F00080 + 6 * 4) +#define PCMD7 __REG(0x40F00080 + 7 * 4) +#define PCMD8 __REG(0x40F00080 + 8 * 4) +#define PCMD9 __REG(0x40F00080 + 9 * 4) +#define PCMD10 __REG(0x40F00080 + 10 * 4) +#define PCMD11 __REG(0x40F00080 + 11 * 4) +#define PCMD12 __REG(0x40F00080 + 12 * 4) +#define PCMD13 __REG(0x40F00080 + 13 * 4) +#define PCMD14 __REG(0x40F00080 + 14 * 4) +#define PCMD15 __REG(0x40F00080 + 15 * 4) +#define PCMD16 __REG(0x40F00080 + 16 * 4) +#define PCMD17 __REG(0x40F00080 + 17 * 4) +#define PCMD18 __REG(0x40F00080 + 18 * 4) +#define PCMD19 __REG(0x40F00080 + 19 * 4) +#define PCMD20 __REG(0x40F00080 + 20 * 4) +#define PCMD21 __REG(0x40F00080 + 21 * 4) +#define PCMD22 __REG(0x40F00080 + 22 * 4) +#define PCMD23 __REG(0x40F00080 + 23 * 4) +#define PCMD24 __REG(0x40F00080 + 24 * 4) +#define PCMD25 __REG(0x40F00080 + 25 * 4) +#define PCMD26 __REG(0x40F00080 + 26 * 4) +#define PCMD27 __REG(0x40F00080 + 27 * 4) +#define PCMD28 __REG(0x40F00080 + 28 * 4) +#define PCMD29 __REG(0x40F00080 + 29 * 4) +#define PCMD30 __REG(0x40F00080 + 30 * 4) +#define PCMD31 __REG(0x40F00080 + 31 * 4) + +#define PCMD_MBC (1<<12) +#define PCMD_DCE (1<<11) +#define PCMD_LC (1<<10) +/* FIXME: PCMD_SQC need be checked. */ +#define PCMD_SQC (3<<8) /* currently only bit 8 is changeable, + bit 9 should be 0 all day. */ +#define PVCR_VCSA (0x1<<14) +#define PVCR_CommandDelay (0xf80) +#define PCFR_PI2C_EN (0x1 << 6) + +#define PSSR_OTGPH (1 << 6) /* OTG Peripheral control Hold */ +#define PSSR_RDH (1 << 5) /* Read Disable Hold */ +#define PSSR_PH (1 << 4) /* Peripheral Control Hold */ +#define PSSR_STS (1 << 3) /* Standby Mode Status */ +#define PSSR_VFS (1 << 2) /* VDD Fault Status */ +#define PSSR_BFS (1 << 1) /* Battery Fault Status */ +#define PSSR_SSS (1 << 0) /* Software Sleep Status */ + +#define PSLR_SL_ROD (1 << 20) /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */ + +#define PCFR_RO (1 << 15) /* RDH Override */ +#define PCFR_PO (1 << 14) /* PH Override */ +#define PCFR_GPROD (1 << 12) /* GPIO nRESET_OUT Disable */ +#define PCFR_L1_EN (1 << 11) /* Sleep Mode L1 converter Enable */ +#define PCFR_FVC (1 << 10) /* Frequency/Voltage Change */ +#define PCFR_DC_EN (1 << 7) /* Sleep/deep-sleep DC-DC Converter Enable */ +#define PCFR_PI2CEN (1 << 6) /* Enable PI2C controller */ +#define PCFR_GPR_EN (1 << 4) /* nRESET_GPIO Pin Enable */ +#define PCFR_DS (1 << 3) /* Deep Sleep Mode */ +#define PCFR_FS (1 << 2) /* Float Static Chip Selects */ +#define PCFR_FP (1 << 1) /* Float PCMCIA controls */ +#define PCFR_OPDE (1 << 0) /* 3.6864 MHz oscillator power-down enable */ + +#define RCSR_GPR (1 << 3) /* GPIO Reset */ +#define RCSR_SMR (1 << 2) /* Sleep Mode */ +#define RCSR_WDR (1 << 1) /* Watchdog Reset */ +#define RCSR_HWR (1 << 0) /* Hardware Reset */ + +#define PWER_GPIO(Nb) (1 << Nb) /* GPIO [0..15] wake-up enable */ +#define PWER_GPIO0 PWER_GPIO (0) /* GPIO [0] wake-up enable */ +#define PWER_GPIO1 PWER_GPIO (1) /* GPIO [1] wake-up enable */ +#define PWER_GPIO2 PWER_GPIO (2) /* GPIO [2] wake-up enable */ +#define PWER_GPIO3 PWER_GPIO (3) /* GPIO [3] wake-up enable */ +#define PWER_GPIO4 PWER_GPIO (4) /* GPIO [4] wake-up enable */ +#define PWER_GPIO5 PWER_GPIO (5) /* GPIO [5] wake-up enable */ +#define PWER_GPIO6 PWER_GPIO (6) /* GPIO [6] wake-up enable */ +#define PWER_GPIO7 PWER_GPIO (7) /* GPIO [7] wake-up enable */ +#define PWER_GPIO8 PWER_GPIO (8) /* GPIO [8] wake-up enable */ +#define PWER_GPIO9 PWER_GPIO (9) /* GPIO [9] wake-up enable */ +#define PWER_GPIO10 PWER_GPIO (10) /* GPIO [10] wake-up enable */ +#define PWER_GPIO11 PWER_GPIO (11) /* GPIO [11] wake-up enable */ +#define PWER_GPIO12 PWER_GPIO (12) /* GPIO [12] wake-up enable */ +#define PWER_GPIO13 PWER_GPIO (13) /* GPIO [13] wake-up enable */ +#define PWER_GPIO14 PWER_GPIO (14) /* GPIO [14] wake-up enable */ +#define PWER_GPIO15 PWER_GPIO (15) /* GPIO [15] wake-up enable */ +#define PWER_RTC 0x80000000 /* RTC alarm wake-up enable */ + +/* + * PXA2xx specific Core clock definitions + */ +#define CCCR __REG(0x41300000) /* Core Clock Configuration Register */ +#define CCSR __REG(0x4130000C) /* Core Clock Status Register */ +#define CKEN __REG(0x41300004) /* Clock Enable Register */ +#define OSCC __REG(0x41300008) /* Oscillator Configuration Register */ + +#define CCCR_N_MASK 0x0380 /* Run Mode Frequency to Turbo Mode Frequency Multiplier */ +#define CCCR_M_MASK 0x0060 /* Memory Frequency to Run Mode Frequency Multiplier */ +#define CCCR_L_MASK 0x001f /* Crystal Frequency to Memory Frequency Multiplier */ + +#define CKEN_AC97CONF (31) /* AC97 Controller Configuration */ +#define CKEN_CAMERA (24) /* Camera Interface Clock Enable */ +#define CKEN_SSP1 (23) /* SSP1 Unit Clock Enable */ +#define CKEN_MEMC (22) /* Memory Controller Clock Enable */ +#define CKEN_MEMSTK (21) /* Memory Stick Host Controller */ +#define CKEN_IM (20) /* Internal Memory Clock Enable */ +#define CKEN_KEYPAD (19) /* Keypad Interface Clock Enable */ +#define CKEN_USIM (18) /* USIM Unit Clock Enable */ +#define CKEN_MSL (17) /* MSL Unit Clock Enable */ +#define CKEN_LCD (16) /* LCD Unit Clock Enable */ +#define CKEN_PWRI2C (15) /* PWR I2C Unit Clock Enable */ +#define CKEN_I2C (14) /* I2C Unit Clock Enable */ +#define CKEN_FICP (13) /* FICP Unit Clock Enable */ +#define CKEN_MMC (12) /* MMC Unit Clock Enable */ +#define CKEN_USB (11) /* USB Unit Clock Enable */ +#define CKEN_ASSP (10) /* ASSP (SSP3) Clock Enable */ +#define CKEN_USBHOST (10) /* USB Host Unit Clock Enable */ +#define CKEN_OSTIMER (9) /* OS Timer Unit Clock Enable */ +#define CKEN_NSSP (9) /* NSSP (SSP2) Clock Enable */ +#define CKEN_I2S (8) /* I2S Unit Clock Enable */ +#define CKEN_BTUART (7) /* BTUART Unit Clock Enable */ +#define CKEN_FFUART (6) /* FFUART Unit Clock Enable */ +#define CKEN_STUART (5) /* STUART Unit Clock Enable */ +#define CKEN_HWUART (4) /* HWUART Unit Clock Enable */ +#define CKEN_SSP3 (4) /* SSP3 Unit Clock Enable */ +#define CKEN_SSP (3) /* SSP Unit Clock Enable */ +#define CKEN_SSP2 (3) /* SSP2 Unit Clock Enable */ +#define CKEN_AC97 (2) /* AC97 Unit Clock Enable */ +#define CKEN_PWM1 (1) /* PWM1 Clock Enable */ +#define CKEN_PWM0 (0) /* PWM0 Clock Enable */ + +#define OSCC_OON (1 << 1) /* 32.768kHz OON (write-once only bit) */ +#define OSCC_OOK (1 << 0) /* 32.768kHz OOK (read-only bit) */ + #endif diff --git a/include/asm-arm/arch-pxa/system.h b/include/asm-arm/arch-pxa/system.h index 9aa6c2e939e..ba7e132de1b 100644 --- a/include/asm-arm/arch-pxa/system.h +++ b/include/asm-arm/arch-pxa/system.h @@ -12,6 +12,7 @@ #include #include "hardware.h" +#include "pxa2xx-regs.h" #include "pxa-regs.h" static inline void arch_idle(void) -- cgit v1.2.3 From 9fc697b0b01416edae99dd9c5c49fb69c9282744 Mon Sep 17 00:00:00 2001 From: Stefan Schmidt Date: Tue, 10 Jun 2008 08:57:27 +0100 Subject: [ARM] 5082/1: pxa: Definition for the third USB port control register UP3OCR This adds the definition for the third USB port control register UP3OCR. It is used on the EZX GSM mobile phones. Signed-off-by: Stefan Schmidt Acked-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa27x-udc.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxa27x-udc.h b/include/asm-arm/arch-pxa/pxa27x-udc.h index 2d4e9cd3a5e..bc1cf7d0773 100644 --- a/include/asm-arm/arch-pxa/pxa27x-udc.h +++ b/include/asm-arm/arch-pxa/pxa27x-udc.h @@ -82,6 +82,7 @@ Interrupt Enable */ #define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */ +#define UP3OCR __REG(0x40600024) /* USB Port 2 Output Control register */ #define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */ #define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */ -- cgit v1.2.3 From 2239aff6ab2b95af1f628eee7a809f21c41605b3 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Mon, 31 Mar 2008 12:38:31 -0400 Subject: [ARM] cache align destination pointer when copying memory for some processors The implementation for memory copy functions on ARM had a (disabled) provision for aligning the source pointer before loading registers with data. Turns out that aligning the _destination_ pointer is much more useful, as the read side is already sufficiently helped with the use of preload. So this changes the definition of the CALGN() macro to target the destination pointer instead, and turns it on for Feroceon processors where the gain is very noticeable. Signed-off-by: Nicolas Pitre Signed-off-by: Lennert Buytenhek --- include/asm-arm/assembler.h | 15 +++++++++++++++ 1 file changed, 15 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/assembler.h b/include/asm-arm/assembler.h index fce83282082..911393b2c6f 100644 --- a/include/asm-arm/assembler.h +++ b/include/asm-arm/assembler.h @@ -55,6 +55,21 @@ #define PLD(code...) #endif +/* + * This can be used to enable code to cacheline align the destination + * pointer when bulk writing to memory. Experiments on StrongARM and + * XScale didn't show this a worthwhile thing to do when the cache is not + * set to write-allocate (this would need further testing on XScale when WA + * is used). + * + * On Feroceon there is much to gain however, regardless of cache mode. + */ +#ifdef CONFIG_CPU_FEROCEON +#define CALGN(code...) code +#else +#define CALGN(code...) +#endif + /* * Enable and disable interrupts */ -- cgit v1.2.3 From 6eef84a5496c678ab27b72bec0fc785c9cee063b Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Wed, 28 May 2008 16:20:56 +0200 Subject: [ARM] Orion: delete unused IO_SPACE_REMAP define This define isn't used anywhere in the kernel tree -- nuke it. Signed-off-by: Lennert Buytenhek Acked-by: Russell King --- include/asm-arm/arch-orion5x/io.h | 1 - 1 file changed, 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-orion5x/io.h b/include/asm-arm/arch-orion5x/io.h index 50f8c880220..d9a4b2065e5 100644 --- a/include/asm-arm/arch-orion5x/io.h +++ b/include/asm-arm/arch-orion5x/io.h @@ -14,7 +14,6 @@ #include "orion5x.h" #define IO_SPACE_LIMIT 0xffffffff -#define IO_SPACE_REMAP ORION5X_PCI_SYS_IO_BASE static inline void __iomem * __arch_ioremap(unsigned long paddr, size_t size, unsigned int mtype) -- cgit v1.2.3 From d2b2a6bbc020e5a9a244f318d28515081e922882 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sat, 31 May 2008 08:30:40 +0200 Subject: [ARM] Orion: add 88F5181L (Orion-VoIP) support Signed-off-by: Lennert Buytenhek Acked-by: Russell King --- include/asm-arm/arch-orion5x/orion5x.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-orion5x/orion5x.h b/include/asm-arm/arch-orion5x/orion5x.h index 206ddd71e19..20f7b406a79 100644 --- a/include/asm-arm/arch-orion5x/orion5x.h +++ b/include/asm-arm/arch-orion5x/orion5x.h @@ -2,7 +2,7 @@ * include/asm-arm/arch-orion5x/orion5x.h * * Generic definitions of Orion SoC flavors: - * Orion-1, Orion-NAS, Orion-VoIP, and Orion-2. + * Orion-1, Orion-VoIP, Orion-NAS, and Orion-2. * * Maintainer: Tzachi Perelstein * @@ -63,9 +63,11 @@ /******************************************************************************* * Supported Devices & Revisions ******************************************************************************/ -/* Orion-1 (88F5181) */ +/* Orion-1 (88F5181) and Orion-VoIP (88F5181L) */ #define MV88F5181_DEV_ID 0x5181 #define MV88F5181_REV_B1 3 +#define MV88F5181L_REV_A0 8 +#define MV88F5181L_REV_A1 9 /* Orion-NAS (88F5182) */ #define MV88F5182_DEV_ID 0x5182 #define MV88F5182_REV_A2 2 -- cgit v1.2.3 From 0e3bc0503f7e7b5b0bd4416f43eeeca1b661e66e Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Wed, 4 Jun 2008 03:16:21 +0200 Subject: [ARM] Orion: use linux/serial_reg.h for Orion uncompress.h Signed-off-by: Lennert Buytenhek --- include/asm-arm/arch-orion5x/uncompress.h | 29 ++++++++++++++++++++++------- 1 file changed, 22 insertions(+), 7 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-orion5x/uncompress.h b/include/asm-arm/arch-orion5x/uncompress.h index 5c13d4fafb4..7548cedf2d7 100644 --- a/include/asm-arm/arch-orion5x/uncompress.h +++ b/include/asm-arm/arch-orion5x/uncompress.h @@ -8,23 +8,38 @@ * warranty of any kind, whether express or implied. */ +#include #include -#define MV_UART_THR ((volatile unsigned char *)(UART0_PHYS_BASE + 0x0)) -#define MV_UART_LSR ((volatile unsigned char *)(UART0_PHYS_BASE + 0x14)) - -#define LSR_THRE 0x20 +#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE) static void putc(const char c) { - int j = 0x1000; - while (--j && !(*MV_UART_LSR & LSR_THRE)) + unsigned char *base = SERIAL_BASE; + int i; + + for (i = 0; i < 0x1000; i++) { + if (base[UART_LSR << 2] & UART_LSR_THRE) + break; barrier(); - *MV_UART_THR = c; + } + + base[UART_TX << 2] = c; } static void flush(void) { + unsigned char *base = SERIAL_BASE; + unsigned char mask; + int i; + + mask = UART_LSR_TEMT | UART_LSR_THRE; + + for (i = 0; i < 0x1000; i++) { + if ((base[UART_LSR << 2] & mask) == mask) + break; + barrier(); + } } /* -- cgit v1.2.3 From 79e90dd5aa95adfdc3117db8a559da3d0195ba58 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Wed, 28 May 2008 16:43:48 +0200 Subject: [ARM] Orion: nuke orion5x_{read,write} Nuke the Orion-specific orion5x_{read,write} wrappers. Signed-off-by: Lennert Buytenhek --- include/asm-arm/arch-orion5x/io.h | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-orion5x/io.h b/include/asm-arm/arch-orion5x/io.h index d9a4b2065e5..59f1bc96a23 100644 --- a/include/asm-arm/arch-orion5x/io.h +++ b/include/asm-arm/arch-orion5x/io.h @@ -52,15 +52,12 @@ static inline void __iomem *__io(unsigned long addr) /***************************************************************************** * Helpers to access Orion registers ****************************************************************************/ -#define orion5x_read(r) __raw_readl(r) -#define orion5x_write(r, val) __raw_writel(val, r) - /* * These are not preempt-safe. Locks, if needed, must be taken * care of by the caller. */ -#define orion5x_setbits(r, mask) orion5x_write((r), orion5x_read(r) | (mask)) -#define orion5x_clrbits(r, mask) orion5x_write((r), orion5x_read(r) & ~(mask)) +#define orion5x_setbits(r, mask) writel(readl(r) | (mask), (r)) +#define orion5x_clrbits(r, mask) writel(readl(r) & ~(mask), (r)) #endif -- cgit v1.2.3 From 1219715de70956557b9dedf3ee021a73d4f4ec52 Mon Sep 17 00:00:00 2001 From: Ke Wei Date: Fri, 23 May 2008 10:23:22 +0200 Subject: [ARM] Orion: add a separate BRIDGE_INT_TIMER1_CLR define Some Feroceon-based SoCs have an MBUS bridge interrupt controller that requires writing a one instead of a zero to clear edge interrupt sources such as timer expiry. This patch adds a new BRIDGE_INT_TIMER1_CLR define, which platform code can set to either ~BRIDGE_INT_TIMER1 (write-zero-to-clear) or BRIDGE_INT_TIMER1 (write-one-to-clear) depending on the platform. Signed-off-by: Lennert Buytenhek --- include/asm-arm/arch-orion5x/orion5x.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-orion5x/orion5x.h b/include/asm-arm/arch-orion5x/orion5x.h index 20f7b406a79..10257f5c5e9 100644 --- a/include/asm-arm/arch-orion5x/orion5x.h +++ b/include/asm-arm/arch-orion5x/orion5x.h @@ -154,6 +154,7 @@ #define BRIDGE_MASK ORION5X_BRIDGE_REG(0x114) #define BRIDGE_INT_TIMER0 0x0002 #define BRIDGE_INT_TIMER1 0x0004 +#define BRIDGE_INT_TIMER1_CLR (~0x0004) #define MAIN_IRQ_CAUSE ORION5X_BRIDGE_REG(0x200) #define MAIN_IRQ_MASK ORION5X_BRIDGE_REG(0x204) -- cgit v1.2.3 From 777f9bebad3476b7dbf5cd8abbd3414139ca0e48 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sun, 22 Jun 2008 22:45:02 +0200 Subject: [ARM] add Marvell Loki (88RC8480) SoC support The Marvell Loki (88RC8480) is an ARM SoC based on a Feroceon CPU core running at between 400 MHz and 1.0 GHz, and features a 64 bit DDR controller, 512K of internal SRAM, two x4 PCI-Express ports, two Gigabit Ethernet ports, two 4x SAS/SATA controllers, two UARTs, two TWSI controllers, and IDMA/XOR engines. This patch adds support for the Marvell LB88RC8480 Development Board, enabling the use of the PCIe interfaces, the ethernet interfaces, the TWSI interfaces and the UARTs. Signed-off-by: Lennert Buytenhek --- include/asm-arm/arch-loki/debug-macro.S | 20 +++++++ include/asm-arm/arch-loki/dma.h | 1 + include/asm-arm/arch-loki/entry-macro.S | 30 ++++++++++ include/asm-arm/arch-loki/hardware.h | 15 +++++ include/asm-arm/arch-loki/io.h | 26 +++++++++ include/asm-arm/arch-loki/irqs.h | 58 ++++++++++++++++++++ include/asm-arm/arch-loki/loki.h | 97 +++++++++++++++++++++++++++++++++ include/asm-arm/arch-loki/memory.h | 14 +++++ include/asm-arm/arch-loki/system.h | 37 +++++++++++++ include/asm-arm/arch-loki/timex.h | 11 ++++ include/asm-arm/arch-loki/uncompress.h | 47 ++++++++++++++++ include/asm-arm/arch-loki/vmalloc.h | 5 ++ 12 files changed, 361 insertions(+) create mode 100644 include/asm-arm/arch-loki/debug-macro.S create mode 100644 include/asm-arm/arch-loki/dma.h create mode 100644 include/asm-arm/arch-loki/entry-macro.S create mode 100644 include/asm-arm/arch-loki/hardware.h create mode 100644 include/asm-arm/arch-loki/io.h create mode 100644 include/asm-arm/arch-loki/irqs.h create mode 100644 include/asm-arm/arch-loki/loki.h create mode 100644 include/asm-arm/arch-loki/memory.h create mode 100644 include/asm-arm/arch-loki/system.h create mode 100644 include/asm-arm/arch-loki/timex.h create mode 100644 include/asm-arm/arch-loki/uncompress.h create mode 100644 include/asm-arm/arch-loki/vmalloc.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-loki/debug-macro.S b/include/asm-arm/arch-loki/debug-macro.S new file mode 100644 index 00000000000..585502e9651 --- /dev/null +++ b/include/asm-arm/arch-loki/debug-macro.S @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-loki/debug-macro.S + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + ldreq \rx, =LOKI_REGS_PHYS_BASE + ldrne \rx, =LOKI_REGS_VIRT_BASE + orr \rx, \rx, #0x00012000 + .endm + +#define UART_SHIFT 2 +#include diff --git a/include/asm-arm/arch-loki/dma.h b/include/asm-arm/arch-loki/dma.h new file mode 100644 index 00000000000..40a8c178f10 --- /dev/null +++ b/include/asm-arm/arch-loki/dma.h @@ -0,0 +1 @@ +/* empty */ diff --git a/include/asm-arm/arch-loki/entry-macro.S b/include/asm-arm/arch-loki/entry-macro.S new file mode 100644 index 00000000000..693257cdbeb --- /dev/null +++ b/include/asm-arm/arch-loki/entry-macro.S @@ -0,0 +1,30 @@ +/* + * include/asm-arm/arch-loki/entry-macro.S + * + * Low-level IRQ helper macros for Marvell Loki (88RC8480) platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include + + .macro disable_fiq + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =IRQ_VIRT_BASE + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + ldr \irqstat, [\base, #IRQ_CAUSE_OFF] + ldr \tmp, [\base, #IRQ_MASK_OFF] + mov \irqnr, #0 + ands \irqstat, \irqstat, \tmp + clzne \irqnr, \irqstat + rsbne \irqnr, \irqnr, #31 + .endm diff --git a/include/asm-arm/arch-loki/hardware.h b/include/asm-arm/arch-loki/hardware.h new file mode 100644 index 00000000000..f65b01c733b --- /dev/null +++ b/include/asm-arm/arch-loki/hardware.h @@ -0,0 +1,15 @@ +/* + * include/asm-arm/arch-loki/hardware.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include "loki.h" + + +#endif diff --git a/include/asm-arm/arch-loki/io.h b/include/asm-arm/arch-loki/io.h new file mode 100644 index 00000000000..e7418a915e7 --- /dev/null +++ b/include/asm-arm/arch-loki/io.h @@ -0,0 +1,26 @@ +/* + * include/asm-arm/arch-loki/io.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IO_H +#define __ASM_ARCH_IO_H + +#include "loki.h" + +#define IO_SPACE_LIMIT 0xffffffff + +static inline void __iomem *__io(unsigned long addr) +{ + return (void __iomem *)((addr - LOKI_PCIE0_IO_PHYS_BASE) + + LOKI_PCIE0_IO_VIRT_BASE); +} + +#define __io(a) __io(a) +#define __mem_pci(a) (a) + + +#endif diff --git a/include/asm-arm/arch-loki/irqs.h b/include/asm-arm/arch-loki/irqs.h new file mode 100644 index 00000000000..7e497143807 --- /dev/null +++ b/include/asm-arm/arch-loki/irqs.h @@ -0,0 +1,58 @@ +/* + * include/asm-arm/arch-loki/irqs.h + * + * IRQ definitions for Marvell Loki (88RC8480) SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IRQS_H +#define __ASM_ARCH_IRQS_H + +#include "loki.h" /* need GPIO_MAX */ + +/* + * Interrupt Controller + */ +#define IRQ_LOKI_PCIE_A_CPU_DRBL 0 +#define IRQ_LOKI_CPU_PCIE_A_DRBL 1 +#define IRQ_LOKI_PCIE_B_CPU_DRBL 2 +#define IRQ_LOKI_CPU_PCIE_B_DRBL 3 +#define IRQ_LOKI_COM_A_ERR 6 +#define IRQ_LOKI_COM_A_IN 7 +#define IRQ_LOKI_COM_A_OUT 8 +#define IRQ_LOKI_COM_B_ERR 9 +#define IRQ_LOKI_COM_B_IN 10 +#define IRQ_LOKI_COM_B_OUT 11 +#define IRQ_LOKI_DMA_A 12 +#define IRQ_LOKI_DMA_B 13 +#define IRQ_LOKI_SAS_A 14 +#define IRQ_LOKI_SAS_B 15 +#define IRQ_LOKI_DDR 16 +#define IRQ_LOKI_XOR 17 +#define IRQ_LOKI_BRIDGE 18 +#define IRQ_LOKI_PCIE_A_ERR 20 +#define IRQ_LOKI_PCIE_A_INT 21 +#define IRQ_LOKI_PCIE_B_ERR 22 +#define IRQ_LOKI_PCIE_B_INT 23 +#define IRQ_LOKI_GBE_A_INT 24 +#define IRQ_LOKI_GBE_B_INT 25 +#define IRQ_LOKI_DEV_ERR 26 +#define IRQ_LOKI_UART0 27 +#define IRQ_LOKI_UART1 28 +#define IRQ_LOKI_TWSI 29 +#define IRQ_LOKI_GPIO_23_0 30 +#define IRQ_LOKI_GPIO_25_24 31 + +/* + * Loki General Purpose Pins + */ +#define IRQ_LOKI_GPIO_START 32 +#define NR_GPIO_IRQS GPIO_MAX + +#define NR_IRQS (IRQ_LOKI_GPIO_START + NR_GPIO_IRQS) + + +#endif diff --git a/include/asm-arm/arch-loki/loki.h b/include/asm-arm/arch-loki/loki.h new file mode 100644 index 00000000000..5dd05ee0a4e --- /dev/null +++ b/include/asm-arm/arch-loki/loki.h @@ -0,0 +1,97 @@ +/* + * include/asm-arm/arch-loki/loki.h + * + * Generic definitions for Marvell Loki (88RC8480) SoC flavors + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_LOKI_H +#define __ASM_ARCH_LOKI_H + +/* + * Marvell Loki (88RC8480) address maps. + * + * phys + * d0000000 on-chip peripheral registers + * e0000000 PCIe 0 Memory space + * e8000000 PCIe 1 Memory space + * f0000000 PCIe 0 I/O space + * f0100000 PCIe 1 I/O space + * + * virt phys size + * fed00000 d0000000 1M on-chip peripheral registers + * fee00000 f0000000 64K PCIe 0 I/O space + * fef00000 f0100000 64K PCIe 1 I/O space + */ + +#define LOKI_REGS_PHYS_BASE 0xd0000000 +#define LOKI_REGS_VIRT_BASE 0xfed00000 +#define LOKI_REGS_SIZE SZ_1M + +#define LOKI_PCIE0_IO_PHYS_BASE 0xf0000000 +#define LOKI_PCIE0_IO_VIRT_BASE 0xfee00000 +#define LOKI_PCIE0_IO_BUS_BASE 0x00000000 +#define LOKI_PCIE0_IO_SIZE SZ_64K + +#define LOKI_PCIE1_IO_PHYS_BASE 0xf0100000 +#define LOKI_PCIE1_IO_VIRT_BASE 0xfef00000 +#define LOKI_PCIE1_IO_BUS_BASE 0x00000000 +#define LOKI_PCIE1_IO_SIZE SZ_64K + +#define LOKI_PCIE0_MEM_PHYS_BASE 0xe0000000 +#define LOKI_PCIE0_MEM_SIZE SZ_128M + +#define LOKI_PCIE1_MEM_PHYS_BASE 0xe8000000 +#define LOKI_PCIE1_MEM_SIZE SZ_128M + +/* + * Register Map + */ +#define DEV_BUS_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x10000) +#define DEV_BUS_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x10000) +#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000) +#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000) +#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100) +#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2100) + +#define BRIDGE_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x20000) +#define BRIDGE_REG(x) (BRIDGE_VIRT_BASE | (x)) +#define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108) +#define SOFT_RESET_OUT_EN 0x00000004 +#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c) +#define SOFT_RESET 0x00000001 +#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE | 0x0110) +#define BRIDGE_MASK (BRIDGE_VIRT_BASE | 0x0114) +#define BRIDGE_INT_TIMER0 0x0002 +#define BRIDGE_INT_TIMER1 0x0004 +#define BRIDGE_INT_TIMER1_CLR 0x0004 +#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0200) +#define IRQ_CAUSE_OFF 0x0000 +#define IRQ_MASK_OFF 0x0004 +#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300) + +#define PCIE0_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x30000) + +#define PCIE1_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x40000) + +#define SAS0_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x80000) + +#define SAS1_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x90000) + +#define GE0_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0xa0000) +#define GE0_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xa0000) + +#define GE1_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0xb0000) +#define GE1_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xb0000) + +#define DDR_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xf0000) +#define DDR_REG(x) (DDR_VIRT_BASE | (x)) + + +#define GPIO_MAX 8 + + +#endif diff --git a/include/asm-arm/arch-loki/memory.h b/include/asm-arm/arch-loki/memory.h new file mode 100644 index 00000000000..835101e4987 --- /dev/null +++ b/include/asm-arm/arch-loki/memory.h @@ -0,0 +1,14 @@ +/* + * include/asm-arm/arch-loki/memory.h + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +#define PHYS_OFFSET UL(0x00000000) + +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + + +#endif diff --git a/include/asm-arm/arch-loki/system.h b/include/asm-arm/arch-loki/system.h new file mode 100644 index 00000000000..a3568ac8ec3 --- /dev/null +++ b/include/asm-arm/arch-loki/system.h @@ -0,0 +1,37 @@ +/* + * include/asm-arm/arch-loki/system.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include +#include + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + +static inline void arch_reset(char mode) +{ + /* + * Enable soft reset to assert RSTOUTn. + */ + writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK); + + /* + * Assert soft reset. + */ + writel(SOFT_RESET, SYSTEM_SOFT_RESET); + + while (1) + ; +} + + +#endif diff --git a/include/asm-arm/arch-loki/timex.h b/include/asm-arm/arch-loki/timex.h new file mode 100644 index 00000000000..940014f97ca --- /dev/null +++ b/include/asm-arm/arch-loki/timex.h @@ -0,0 +1,11 @@ +/* + * include/asm-arm/arch-loki/timex.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#define CLOCK_TICK_RATE (100 * HZ) + +#define LOKI_TCLK 180000000 diff --git a/include/asm-arm/arch-loki/uncompress.h b/include/asm-arm/arch-loki/uncompress.h new file mode 100644 index 00000000000..89a0cf88d3a --- /dev/null +++ b/include/asm-arm/arch-loki/uncompress.h @@ -0,0 +1,47 @@ +/* + * include/asm-arm/arch-loki/uncompress.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include + +#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE) + +static void putc(const char c) +{ + unsigned char *base = SERIAL_BASE; + int i; + + for (i = 0; i < 0x1000; i++) { + if (base[UART_LSR << 2] & UART_LSR_THRE) + break; + barrier(); + } + + base[UART_TX << 2] = c; +} + +static void flush(void) +{ + unsigned char *base = SERIAL_BASE; + unsigned char mask; + int i; + + mask = UART_LSR_TEMT | UART_LSR_THRE; + + for (i = 0; i < 0x1000; i++) { + if ((base[UART_LSR << 2] & mask) == mask) + break; + barrier(); + } +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/include/asm-arm/arch-loki/vmalloc.h b/include/asm-arm/arch-loki/vmalloc.h new file mode 100644 index 00000000000..f5be0622049 --- /dev/null +++ b/include/asm-arm/arch-loki/vmalloc.h @@ -0,0 +1,5 @@ +/* + * include/asm-arm/arch-loki/vmalloc.h + */ + +#define VMALLOC_END 0xfe800000 -- cgit v1.2.3 From 836a8051d54525e0782f156dcfa3c13d30f22840 Mon Sep 17 00:00:00 2001 From: Stanislav Samsonov Date: Tue, 3 Jun 2008 11:24:40 +0300 Subject: [ARM] Feroceon: L1 cache range operation support This patch adds support for the L1 D cache range operations that are supported by the Marvell Discovery Duo and Marvell Kirkwood ARM SoCs. Signed-off-by: Stanislav Samsonov Acked-by: Saeed Bishara Reviewed-by: Nicolas Pitre Signed-off-by: Lennert Buytenhek --- include/asm-arm/cacheflush.h | 6 +----- 1 file changed, 1 insertion(+), 5 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/cacheflush.h b/include/asm-arm/cacheflush.h index 759a97b56ee..b85d426bb52 100644 --- a/include/asm-arm/cacheflush.h +++ b/include/asm-arm/cacheflush.h @@ -95,11 +95,7 @@ #endif #if defined(CONFIG_CPU_FEROCEON) -# ifdef _CACHE -# define MULTI_CACHE 1 -# else -# define _CACHE feroceon -# endif +# define MULTI_CACHE 1 #endif #if defined(CONFIG_CPU_V6) -- cgit v1.2.3 From 99c6dc117d27d6259214812bd0b113aaf467f600 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sun, 22 Jun 2008 22:45:04 +0200 Subject: [ARM] Feroceon: L2 cache support This patch adds support for the unified Feroceon L2 cache controller as found in e.g. the Marvell Kirkwood and Marvell Discovery Duo families of ARM SoCs. Note that: - Page table walks are outer uncacheable on Kirkwood and Discovery Duo, since the ARMv5 spec provides no way to indicate outer cacheability of page table walks (specifying it in TTBR[4:3] is an ARMv6+ feature). This requires adding L2 cache clean instructions to proc-feroceon.S (dcache_clean_area(), set_pte()) as well as to tlbflush.h ({flush,clean}_pmd_entry()). The latter case is handled by defining a new TLB type (TLB_FEROCEON) which is almost identical to the v4wbi one but provides a TLB_L2CLEAN_FR flag. - The Feroceon L2 cache controller supports L2 range (i.e. 'clean L2 range by MVA' and 'invalidate L2 range by MVA') operations, and this patch uses those range operations for all Linux outer cache operations, as they are faster than the regular per-line operations. L2 range operations are not interruptible on this hardware, which avoids potential livelock issues, but can be bad for interrupt latency, so there is a compile-time tunable (MAX_RANGE_SIZE) which allows you to select the maximum range size to operate on at once. (Valid range is between one cache line and one 4KiB page, and must be a multiple of the line size.) Signed-off-by: Lennert Buytenhek --- include/asm-arm/plat-orion/cache-feroceon-l2.h | 11 ++++++++++ include/asm-arm/tlbflush.h | 30 ++++++++++++++++++++++++++ 2 files changed, 41 insertions(+) create mode 100644 include/asm-arm/plat-orion/cache-feroceon-l2.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-orion/cache-feroceon-l2.h b/include/asm-arm/plat-orion/cache-feroceon-l2.h new file mode 100644 index 00000000000..ba4e016d3ec --- /dev/null +++ b/include/asm-arm/plat-orion/cache-feroceon-l2.h @@ -0,0 +1,11 @@ +/* + * include/asm-arm/plat-orion/cache-feroceon-l2.h + * + * Copyright (C) 2008 Marvell Semiconductor + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +extern void __init feroceon_l2_init(int l2_wt_override); diff --git a/include/asm-arm/tlbflush.h b/include/asm-arm/tlbflush.h index 8c6bc1bb9d1..909656c747e 100644 --- a/include/asm-arm/tlbflush.h +++ b/include/asm-arm/tlbflush.h @@ -39,6 +39,7 @@ #define TLB_V6_D_ASID (1 << 17) #define TLB_V6_I_ASID (1 << 18) +#define TLB_L2CLEAN_FR (1 << 29) /* Feroceon */ #define TLB_DCLEAN (1 << 30) #define TLB_WB (1 << 31) @@ -51,6 +52,7 @@ * v4 - ARMv4 without write buffer * v4wb - ARMv4 with write buffer without I TLB flush entry instruction * v4wbi - ARMv4 with write buffer with I TLB flush entry instruction + * fr - Feroceon (v4wbi with non-outer-cacheable page table walks) * v6wbi - ARMv6 with write buffer with I TLB flush entry instruction */ #undef _TLB @@ -103,6 +105,23 @@ # define v4wbi_always_flags (-1UL) #endif +#define fr_tlb_flags (TLB_WB | TLB_DCLEAN | TLB_L2CLEAN_FR | \ + TLB_V4_I_FULL | TLB_V4_D_FULL | \ + TLB_V4_I_PAGE | TLB_V4_D_PAGE) + +#ifdef CONFIG_CPU_TLB_FEROCEON +# define fr_possible_flags fr_tlb_flags +# define fr_always_flags fr_tlb_flags +# ifdef _TLB +# define MULTI_TLB 1 +# else +# define _TLB v4wbi +# endif +#else +# define fr_possible_flags 0 +# define fr_always_flags (-1UL) +#endif + #define v4wb_tlb_flags (TLB_WB | TLB_DCLEAN | \ TLB_V4_I_FULL | TLB_V4_D_FULL | \ TLB_V4_D_PAGE) @@ -245,12 +264,14 @@ extern struct cpu_tlb_fns cpu_tlb; #define possible_tlb_flags (v3_possible_flags | \ v4_possible_flags | \ v4wbi_possible_flags | \ + fr_possible_flags | \ v4wb_possible_flags | \ v6wbi_possible_flags) #define always_tlb_flags (v3_always_flags & \ v4_always_flags & \ v4wbi_always_flags & \ + fr_always_flags & \ v4wb_always_flags & \ v6wbi_always_flags) @@ -417,6 +438,11 @@ static inline void flush_pmd_entry(pmd_t *pmd) if (tlb_flag(TLB_DCLEAN)) asm("mcr p15, 0, %0, c7, c10, 1 @ flush_pmd" : : "r" (pmd) : "cc"); + + if (tlb_flag(TLB_L2CLEAN_FR)) + asm("mcr p15, 1, %0, c15, c9, 1 @ L2 flush_pmd" + : : "r" (pmd) : "cc"); + if (tlb_flag(TLB_WB)) dsb(); } @@ -428,6 +454,10 @@ static inline void clean_pmd_entry(pmd_t *pmd) if (tlb_flag(TLB_DCLEAN)) asm("mcr p15, 0, %0, c7, c10, 1 @ flush_pmd" : : "r" (pmd) : "cc"); + + if (tlb_flag(TLB_L2CLEAN_FR)) + asm("mcr p15, 1, %0, c15, c9, 1 @ L2 flush_pmd" + : : "r" (pmd) : "cc"); } #undef tlb_flag -- cgit v1.2.3 From 651c74c74bf84ba966b52588ba3329606f3fd8d4 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Sun, 22 Jun 2008 22:45:06 +0200 Subject: [ARM] add Marvell Kirkwood (88F6000) SoC support The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface, a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS interface, and IDMA/XOR engines, and depending on the model, also features one or two Gigabit Ethernet interfaces, two SATA II interfaces, one or two TWSI interfaces, one or two UARTs, a TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and an SDIO interface. This patch adds supports for the Marvell DB-88F6281-BP Development Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs, enabling support for the PCIe interface, the USB interface, the ethernet interfaces, the SATA interfaces, the TWSI interfaces, the UARTs, and the NAND controller. Signed-off-by: Saeed Bishara Signed-off-by: Lennert Buytenhek --- include/asm-arm/arch-kirkwood/debug-macro.S | 20 ++++++ include/asm-arm/arch-kirkwood/dma.h | 1 + include/asm-arm/arch-kirkwood/entry-macro.S | 40 ++++++++++++ include/asm-arm/arch-kirkwood/hardware.h | 21 ++++++ include/asm-arm/arch-kirkwood/io.h | 26 ++++++++ include/asm-arm/arch-kirkwood/irqs.h | 63 ++++++++++++++++++ include/asm-arm/arch-kirkwood/kirkwood.h | 99 +++++++++++++++++++++++++++++ include/asm-arm/arch-kirkwood/memory.h | 14 ++++ include/asm-arm/arch-kirkwood/system.h | 37 +++++++++++ include/asm-arm/arch-kirkwood/timex.h | 11 ++++ include/asm-arm/arch-kirkwood/uncompress.h | 47 ++++++++++++++ include/asm-arm/arch-kirkwood/vmalloc.h | 5 ++ 12 files changed, 384 insertions(+) create mode 100644 include/asm-arm/arch-kirkwood/debug-macro.S create mode 100644 include/asm-arm/arch-kirkwood/dma.h create mode 100644 include/asm-arm/arch-kirkwood/entry-macro.S create mode 100644 include/asm-arm/arch-kirkwood/hardware.h create mode 100644 include/asm-arm/arch-kirkwood/io.h create mode 100644 include/asm-arm/arch-kirkwood/irqs.h create mode 100644 include/asm-arm/arch-kirkwood/kirkwood.h create mode 100644 include/asm-arm/arch-kirkwood/memory.h create mode 100644 include/asm-arm/arch-kirkwood/system.h create mode 100644 include/asm-arm/arch-kirkwood/timex.h create mode 100644 include/asm-arm/arch-kirkwood/uncompress.h create mode 100644 include/asm-arm/arch-kirkwood/vmalloc.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-kirkwood/debug-macro.S b/include/asm-arm/arch-kirkwood/debug-macro.S new file mode 100644 index 00000000000..f55fb8ad9ee --- /dev/null +++ b/include/asm-arm/arch-kirkwood/debug-macro.S @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-kirkwood/debug-macro.S + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + ldreq \rx, =KIRKWOOD_REGS_PHYS_BASE + ldrne \rx, =KIRKWOOD_REGS_VIRT_BASE + orr \rx, \rx, #0x00012000 + .endm + +#define UART_SHIFT 2 +#include diff --git a/include/asm-arm/arch-kirkwood/dma.h b/include/asm-arm/arch-kirkwood/dma.h new file mode 100644 index 00000000000..40a8c178f10 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/dma.h @@ -0,0 +1 @@ +/* empty */ diff --git a/include/asm-arm/arch-kirkwood/entry-macro.S b/include/asm-arm/arch-kirkwood/entry-macro.S new file mode 100644 index 00000000000..fc6a43d9355 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/entry-macro.S @@ -0,0 +1,40 @@ +/* + * include/asm-arm/arch-kirkwood/entry-macro.S + * + * Low-level IRQ helper macros for Marvell Kirkwood platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include + + .macro disable_fiq + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =IRQ_VIRT_BASE + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + @ check low interrupts + ldr \irqstat, [\base, #IRQ_CAUSE_LOW_OFF] + ldr \tmp, [\base, #IRQ_MASK_LOW_OFF] + mov \irqnr, #31 + ands \irqstat, \irqstat, \tmp + bne 1001f + + @ if no low interrupts set, check high interrupts + ldr \irqstat, [\base, #IRQ_CAUSE_HIGH_OFF] + ldr \tmp, [\base, #IRQ_MASK_HIGH_OFF] + mov \irqnr, #63 + ands \irqstat, \irqstat, \tmp + + @ find first active interrupt source +1001: clzne \irqstat, \irqstat + subne \irqnr, \irqnr, \irqstat + .endm diff --git a/include/asm-arm/arch-kirkwood/hardware.h b/include/asm-arm/arch-kirkwood/hardware.h new file mode 100644 index 00000000000..e695719771a --- /dev/null +++ b/include/asm-arm/arch-kirkwood/hardware.h @@ -0,0 +1,21 @@ +/* + * include/asm-arm/arch-kirkwood/hardware.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include "kirkwood.h" + +#define pcibios_assign_all_busses() 1 + +#define PCIBIOS_MIN_IO 0x00001000 +#define PCIBIOS_MIN_MEM 0x01000000 +#define PCIMEM_BASE KIRKWOOD_PCIE_MEM_PHYS_BASE /* mem base for VGA */ + + +#endif diff --git a/include/asm-arm/arch-kirkwood/io.h b/include/asm-arm/arch-kirkwood/io.h new file mode 100644 index 00000000000..0ef6e95f5d5 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/io.h @@ -0,0 +1,26 @@ +/* + * include/asm-arm/arch-kirkwood/io.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IO_H +#define __ASM_ARCH_IO_H + +#include "kirkwood.h" + +#define IO_SPACE_LIMIT 0xffffffff + +static inline void __iomem *__io(unsigned long addr) +{ + return (void __iomem *)((addr - KIRKWOOD_PCIE_IO_PHYS_BASE) + + KIRKWOOD_PCIE_IO_VIRT_BASE); +} + +#define __io(a) __io(a) +#define __mem_pci(a) (a) + + +#endif diff --git a/include/asm-arm/arch-kirkwood/irqs.h b/include/asm-arm/arch-kirkwood/irqs.h new file mode 100644 index 00000000000..2e7b5da6335 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/irqs.h @@ -0,0 +1,63 @@ +/* + * include/asm-arm/arch-kirkwood/irqs.h + * + * IRQ definitions for Marvell Kirkwood SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IRQS_H +#define __ASM_ARCH_IRQS_H + +#include "kirkwood.h" /* need GPIO_MAX */ + +/* + * Low Interrupt Controller + */ +#define IRQ_KIRKWOOD_HIGH_SUM 0 +#define IRQ_KIRKWOOD_BRIDGE 1 +#define IRQ_KIRKWOOD_HOST2CPU 2 +#define IRQ_KIRKWOOD_CPU2HOST 3 +#define IRQ_KIRKWOOD_XOR_00 5 +#define IRQ_KIRKWOOD_XOR_01 6 +#define IRQ_KIRKWOOD_XOR_10 7 +#define IRQ_KIRKWOOD_XOR_11 8 +#define IRQ_KIRKWOOD_PCIE 9 +#define IRQ_KIRKWOOD_GE00_SUM 11 +#define IRQ_KIRKWOOD_GE01_SUM 15 +#define IRQ_KIRKWOOD_USB 19 +#define IRQ_KIRKWOOD_SATA 21 +#define IRQ_KIRKWOOD_CRYPTO 22 +#define IRQ_KIRKWOOD_SPI 23 +#define IRQ_KIRKWOOD_I2S 24 +#define IRQ_KIRKWOOD_TS_0 26 +#define IRQ_KIRKWOOD_SDIO 28 +#define IRQ_KIRKWOOD_TWSI 29 +#define IRQ_KIRKWOOD_AVB 30 +#define IRQ_KIRKWOOD_TDMI 31 + +/* + * High Interrupt Controller + */ +#define IRQ_KIRKWOOD_UART_0 33 +#define IRQ_KIRKWOOD_UART_1 34 +#define IRQ_KIRKWOOD_GPIO_LOW_0_7 35 +#define IRQ_KIRKWOOD_GPIO_LOW_8_15 36 +#define IRQ_KIRKWOOD_GPIO_LOW_16_23 37 +#define IRQ_KIRKWOOD_GPIO_LOW_24_31 38 +#define IRQ_KIRKWOOD_GPIO_HIGH_0_7 39 +#define IRQ_KIRKWOOD_GPIO_HIGH_8_15 40 +#define IRQ_KIRKWOOD_GPIO_HIGH_16_23 41 + +/* + * KIRKWOOD General Purpose Pins + */ +#define IRQ_KIRKWOOD_GPIO_START 64 +#define NR_GPIO_IRQS GPIO_MAX + +#define NR_IRQS (IRQ_KIRKWOOD_GPIO_START + NR_GPIO_IRQS) + + +#endif diff --git a/include/asm-arm/arch-kirkwood/kirkwood.h b/include/asm-arm/arch-kirkwood/kirkwood.h new file mode 100644 index 00000000000..520250dbd8a --- /dev/null +++ b/include/asm-arm/arch-kirkwood/kirkwood.h @@ -0,0 +1,99 @@ +/* + * include/asm-arm/arch-kirkwood/kirkwood.h + * + * Generic definitions for Marvell Kirkwood SoC flavors: + * 88F6180, 88F6192 and 88F6281. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_KIRKWOOD_H +#define __ASM_ARCH_KIRKWOOD_H + +/* + * Marvell Kirkwood address maps. + * + * phys + * e0000000 PCIe Memory space + * f1000000 on-chip peripheral registers + * f2000000 PCIe I/O space + * f3000000 NAND controller address window + * + * virt phys size + * fee00000 f1000000 1M on-chip peripheral registers + * fef00000 f2000000 1M PCIe I/O space + */ + +#define KIRKWOOD_NAND_MEM_PHYS_BASE 0xf3000000 +#define KIRKWOOD_NAND_MEM_SIZE SZ_64K /* 1K is sufficient, but 64K + * is the minimal window size + */ + +#define KIRKWOOD_PCIE_IO_PHYS_BASE 0xf2000000 +#define KIRKWOOD_PCIE_IO_VIRT_BASE 0xfef00000 +#define KIRKWOOD_PCIE_IO_BUS_BASE 0x00000000 +#define KIRKWOOD_PCIE_IO_SIZE SZ_1M + +#define KIRKWOOD_REGS_PHYS_BASE 0xf1000000 +#define KIRKWOOD_REGS_VIRT_BASE 0xfee00000 +#define KIRKWOOD_REGS_SIZE SZ_1M + +#define KIRKWOOD_PCIE_MEM_PHYS_BASE 0xe0000000 +#define KIRKWOOD_PCIE_MEM_SIZE SZ_128M + +/* + * MBUS bridge registers. + */ +#define BRIDGE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x20000) +#define CPU_CONTROL (BRIDGE_VIRT_BASE | 0x0104) +#define CPU_RESET 0x00000002 +//#define L2_WRITETHROUGH 0x00020000 +#define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108) +#define SOFT_RESET_OUT_EN 0x00000004 +#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c) +#define SOFT_RESET 0x00000001 +#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE | 0x0110) +#define BRIDGE_MASK (BRIDGE_VIRT_BASE | 0x0114) +#define BRIDGE_INT_TIMER0 0x0002 +#define BRIDGE_INT_TIMER1 0x0004 +#define BRIDGE_INT_TIMER1_CLR (~0x0004) +#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0200) +#define IRQ_CAUSE_LOW_OFF 0x0000 +#define IRQ_MASK_LOW_OFF 0x0004 +#define IRQ_CAUSE_HIGH_OFF 0x0010 +#define IRQ_MASK_HIGH_OFF 0x0014 +#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300) + +/* + * Register Map + */ +#define DDR_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x00000) +#define DDR_WINDOW_CPU_BASE (DDR_VIRT_BASE | 0x1500) + +#define DEV_BUS_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x10000) +#define DEV_BUS_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x10000) +#define SAMPLE_AT_RESET (DEV_BUS_VIRT_BASE | 0x0030) +#define DEVICE_ID (DEV_BUS_VIRT_BASE | 0x0034) +#define RTC_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x0300) +#define SPI_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x0600) +#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000) +#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000) +#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100) +#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2100) + +#define PCIE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x40000) + +#define USB_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x50000) + +#define GE00_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x70000) +#define GE01_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x74000) + +#define SATA_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x80000) + + +#define GPIO_MAX 50 + + +#endif diff --git a/include/asm-arm/arch-kirkwood/memory.h b/include/asm-arm/arch-kirkwood/memory.h new file mode 100644 index 00000000000..e5108f408ce --- /dev/null +++ b/include/asm-arm/arch-kirkwood/memory.h @@ -0,0 +1,14 @@ +/* + * include/asm-arm/arch-kirkwood/memory.h + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +#define PHYS_OFFSET UL(0x00000000) + +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + + +#endif diff --git a/include/asm-arm/arch-kirkwood/system.h b/include/asm-arm/arch-kirkwood/system.h new file mode 100644 index 00000000000..8dde7e37985 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/system.h @@ -0,0 +1,37 @@ +/* + * include/asm-arm/arch-kirkwood/system.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include +#include + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + +static inline void arch_reset(char mode) +{ + /* + * Enable soft reset to assert RSTOUTn. + */ + writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK); + + /* + * Assert soft reset. + */ + writel(SOFT_RESET, SYSTEM_SOFT_RESET); + + while (1) + ; +} + + +#endif diff --git a/include/asm-arm/arch-kirkwood/timex.h b/include/asm-arm/arch-kirkwood/timex.h new file mode 100644 index 00000000000..82122e134e3 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/timex.h @@ -0,0 +1,11 @@ +/* + * include/asm-arm/arch-kirkwood/timex.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#define CLOCK_TICK_RATE (100 * HZ) + +#define KIRKWOOD_TCLK 166666667 diff --git a/include/asm-arm/arch-kirkwood/uncompress.h b/include/asm-arm/arch-kirkwood/uncompress.h new file mode 100644 index 00000000000..a9062b6d768 --- /dev/null +++ b/include/asm-arm/arch-kirkwood/uncompress.h @@ -0,0 +1,47 @@ +/* + * include/asm-arm/arch-kirkwood/uncompress.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include + +#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE) + +static void putc(const char c) +{ + unsigned char *base = SERIAL_BASE; + int i; + + for (i = 0; i < 0x1000; i++) { + if (base[UART_LSR << 2] & UART_LSR_THRE) + break; + barrier(); + } + + base[UART_TX << 2] = c; +} + +static void flush(void) +{ + unsigned char *base = SERIAL_BASE; + unsigned char mask; + int i; + + mask = UART_LSR_TEMT | UART_LSR_THRE; + + for (i = 0; i < 0x1000; i++) { + if ((base[UART_LSR << 2] & mask) == mask) + break; + barrier(); + } +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/include/asm-arm/arch-kirkwood/vmalloc.h b/include/asm-arm/arch-kirkwood/vmalloc.h new file mode 100644 index 00000000000..41852c6e77f --- /dev/null +++ b/include/asm-arm/arch-kirkwood/vmalloc.h @@ -0,0 +1,5 @@ +/* + * include/asm-arm/arch-kirkwood/vmalloc.h + */ + +#define VMALLOC_END 0xfe800000 -- cgit v1.2.3 From a9311cfed241ebcd6b5f9be5c8c6d519bf22f9e7 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sun, 22 Jun 2008 22:45:09 +0200 Subject: [ARM] Orion: PCIe x4/x1 detection support The Discovery Duo (MV78xx0) has two x4 PCIe ports which can either be used in x4 mode or in quad x1 mode. This patch adds an accessor function to the generic plat-orion PCIe handling code to detect in which of the two modes we're running (which is determined by strap pins and/or configured by the bootloader). Signed-off-by: Lennert Buytenhek --- include/asm-arm/plat-orion/pcie.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-orion/pcie.h b/include/asm-arm/plat-orion/pcie.h index 6434ac685d2..e61b7bd97af 100644 --- a/include/asm-arm/plat-orion/pcie.h +++ b/include/asm-arm/plat-orion/pcie.h @@ -14,6 +14,7 @@ u32 orion_pcie_dev_id(void __iomem *base); u32 orion_pcie_rev(void __iomem *base); int orion_pcie_link_up(void __iomem *base); +int orion_pcie_x4_mode(void __iomem *base); int orion_pcie_get_local_bus_nr(void __iomem *base); void orion_pcie_set_local_bus_nr(void __iomem *base, int nr); void orion_pcie_setup(void __iomem *base, -- cgit v1.2.3 From 794d15b25df5dda10efba600d6dd6cd74a7aa9cb Mon Sep 17 00:00:00 2001 From: Stanislav Samsonov Date: Sun, 22 Jun 2008 22:45:10 +0200 Subject: [ARM] add Marvell 78xx0 ARM SoC support The Marvell Discovery Duo (MV78xx0) is a family of ARM SoCs featuring (depending on the model) one or two Feroceon CPU cores with 512K of L2 cache and VFP coprocessors running at (depending on the model) between 800 MHz and 1.2 GHz, and features a DDR2 controller, two PCIe interfaces that can each run either in x4 or quad x1 mode, three USB 2.0 interfaces, two 3Gb/s SATA II interfaces, a SPI interface, two TWSI interfaces, a crypto accelerator, IDMA/XOR engines, a SPI interface, four UARTs, and depending on the model, two or four gigabit ethernet interfaces. This patch adds basic support for the platform, and allows booting on the MV78x00 development board, with functional UARTs, SATA, PCIe, GigE and USB ports. Signed-off-by: Stanislav Samsonov Signed-off-by: Lennert Buytenhek --- include/asm-arm/arch-mv78xx0/debug-macro.S | 20 +++++ include/asm-arm/arch-mv78xx0/dma.h | 1 + include/asm-arm/arch-mv78xx0/entry-macro.S | 39 +++++++++ include/asm-arm/arch-mv78xx0/hardware.h | 21 +++++ include/asm-arm/arch-mv78xx0/io.h | 26 ++++++ include/asm-arm/arch-mv78xx0/irqs.h | 91 +++++++++++++++++++++ include/asm-arm/arch-mv78xx0/memory.h | 14 ++++ include/asm-arm/arch-mv78xx0/mv78xx0.h | 126 +++++++++++++++++++++++++++++ include/asm-arm/arch-mv78xx0/system.h | 37 +++++++++ include/asm-arm/arch-mv78xx0/timex.h | 9 +++ include/asm-arm/arch-mv78xx0/uncompress.h | 47 +++++++++++ include/asm-arm/arch-mv78xx0/vmalloc.h | 5 ++ 12 files changed, 436 insertions(+) create mode 100644 include/asm-arm/arch-mv78xx0/debug-macro.S create mode 100644 include/asm-arm/arch-mv78xx0/dma.h create mode 100644 include/asm-arm/arch-mv78xx0/entry-macro.S create mode 100644 include/asm-arm/arch-mv78xx0/hardware.h create mode 100644 include/asm-arm/arch-mv78xx0/io.h create mode 100644 include/asm-arm/arch-mv78xx0/irqs.h create mode 100644 include/asm-arm/arch-mv78xx0/memory.h create mode 100644 include/asm-arm/arch-mv78xx0/mv78xx0.h create mode 100644 include/asm-arm/arch-mv78xx0/system.h create mode 100644 include/asm-arm/arch-mv78xx0/timex.h create mode 100644 include/asm-arm/arch-mv78xx0/uncompress.h create mode 100644 include/asm-arm/arch-mv78xx0/vmalloc.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mv78xx0/debug-macro.S b/include/asm-arm/arch-mv78xx0/debug-macro.S new file mode 100644 index 00000000000..d0595bd645e --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/debug-macro.S @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-mv78xx0/debug-macro.S + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + ldreq \rx, =MV78XX0_REGS_PHYS_BASE + ldrne \rx, =MV78XX0_REGS_VIRT_BASE + orr \rx, \rx, #0x00012000 + .endm + +#define UART_SHIFT 2 +#include diff --git a/include/asm-arm/arch-mv78xx0/dma.h b/include/asm-arm/arch-mv78xx0/dma.h new file mode 100644 index 00000000000..40a8c178f10 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/dma.h @@ -0,0 +1 @@ +/* empty */ diff --git a/include/asm-arm/arch-mv78xx0/entry-macro.S b/include/asm-arm/arch-mv78xx0/entry-macro.S new file mode 100644 index 00000000000..e9a606b1266 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/entry-macro.S @@ -0,0 +1,39 @@ +/* + * include/asm-arm/arch-mv78xx0/entry-macro.S + * + * Low-level IRQ helper macros for Marvell MV78xx0 platforms + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include + + .macro disable_fiq + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =IRQ_VIRT_BASE + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + @ check low interrupts + ldr \irqstat, [\base, #IRQ_CAUSE_LOW_OFF] + ldr \tmp, [\base, #IRQ_MASK_LOW_OFF] + mov \irqnr, #31 + ands \irqstat, \irqstat, \tmp + + @ if no low interrupts set, check high interrupts + ldreq \irqstat, [\base, #IRQ_CAUSE_HIGH_OFF] + ldreq \tmp, [\base, #IRQ_MASK_HIGH_OFF] + moveq \irqnr, #63 + andeqs \irqstat, \irqstat, \tmp + + @ find first active interrupt source + clzne \irqstat, \irqstat + subne \irqnr, \irqnr, \irqstat + .endm diff --git a/include/asm-arm/arch-mv78xx0/hardware.h b/include/asm-arm/arch-mv78xx0/hardware.h new file mode 100644 index 00000000000..8e17926086c --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/hardware.h @@ -0,0 +1,21 @@ +/* + * include/asm-arm/arch-mv78xx0/hardware.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include "mv78xx0.h" + +#define pcibios_assign_all_busses() 1 + +#define PCIBIOS_MIN_IO 0x00001000 +#define PCIBIOS_MIN_MEM 0x01000000 +#define PCIMEM_BASE MV78XX0_PCIE_MEM_PHYS_BASE /* mem base for VGA */ + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/io.h b/include/asm-arm/arch-mv78xx0/io.h new file mode 100644 index 00000000000..415d4c98e3d --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/io.h @@ -0,0 +1,26 @@ +/* + * include/asm-arm/arch-mv78xx0/io.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IO_H +#define __ASM_ARCH_IO_H + +#include "mv78xx0.h" + +#define IO_SPACE_LIMIT 0xffffffff + +static inline void __iomem *__io(unsigned long addr) +{ + return (void __iomem *)((addr - MV78XX0_PCIE_IO_PHYS_BASE(0)) + + MV78XX0_PCIE_IO_VIRT_BASE(0)); +} + +#define __io(a) __io(a) +#define __mem_pci(a) (a) + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/irqs.h b/include/asm-arm/arch-mv78xx0/irqs.h new file mode 100644 index 00000000000..75930450cd6 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/irqs.h @@ -0,0 +1,91 @@ +/* + * include/asm-arm/arch-mv78xx0/irqs.h + * + * IRQ definitions for Marvell MV78xx0 SoCs + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_IRQS_H +#define __ASM_ARCH_IRQS_H + +#include "mv78xx0.h" /* need GPIO_MAX */ + +/* + * MV78xx0 Low Interrupt Controller + */ +#define IRQ_MV78XX0_ERR 0 +#define IRQ_MV78XX0_SPI 1 +#define IRQ_MV78XX0_I2C_0 2 +#define IRQ_MV78XX0_I2C_1 3 +#define IRQ_MV78XX0_IDMA_0 4 +#define IRQ_MV78XX0_IDMA_1 5 +#define IRQ_MV78XX0_IDMA_2 6 +#define IRQ_MV78XX0_IDMA_3 7 +#define IRQ_MV78XX0_TIMER_0 8 +#define IRQ_MV78XX0_TIMER_1 9 +#define IRQ_MV78XX0_TIMER_2 10 +#define IRQ_MV78XX0_TIMER_3 11 +#define IRQ_MV78XX0_UART_0 12 +#define IRQ_MV78XX0_UART_1 13 +#define IRQ_MV78XX0_UART_2 14 +#define IRQ_MV78XX0_UART_3 15 +#define IRQ_MV78XX0_USB_0 16 +#define IRQ_MV78XX0_USB_1 17 +#define IRQ_MV78XX0_USB_2 18 +#define IRQ_MV78XX0_CRYPTO 19 +#define IRQ_MV78XX0_SDIO_0 20 +#define IRQ_MV78XX0_SDIO_1 21 +#define IRQ_MV78XX0_XOR_0 22 +#define IRQ_MV78XX0_XOR_1 23 +#define IRQ_MV78XX0_I2S_0 24 +#define IRQ_MV78XX0_I2S_1 25 +#define IRQ_MV78XX0_SATA 26 +#define IRQ_MV78XX0_TDMI 27 + +/* + * MV78xx0 High Interrupt Controller + */ +#define IRQ_MV78XX0_PCIE_00 32 +#define IRQ_MV78XX0_PCIE_01 33 +#define IRQ_MV78XX0_PCIE_02 34 +#define IRQ_MV78XX0_PCIE_03 35 +#define IRQ_MV78XX0_PCIE_10 36 +#define IRQ_MV78XX0_PCIE_11 37 +#define IRQ_MV78XX0_PCIE_12 38 +#define IRQ_MV78XX0_PCIE_13 39 +#define IRQ_MV78XX0_GE00_SUM 40 +#define IRQ_MV78XX0_GE00_RX 41 +#define IRQ_MV78XX0_GE00_TX 42 +#define IRQ_MV78XX0_GE00_MISC 43 +#define IRQ_MV78XX0_GE01_SUM 44 +#define IRQ_MV78XX0_GE01_RX 45 +#define IRQ_MV78XX0_GE01_TX 46 +#define IRQ_MV78XX0_GE01_MISC 47 +#define IRQ_MV78XX0_GE10_SUM 48 +#define IRQ_MV78XX0_GE10_RX 49 +#define IRQ_MV78XX0_GE10_TX 50 +#define IRQ_MV78XX0_GE10_MISC 51 +#define IRQ_MV78XX0_GE11_SUM 52 +#define IRQ_MV78XX0_GE11_RX 53 +#define IRQ_MV78XX0_GE11_TX 54 +#define IRQ_MV78XX0_GE11_MISC 55 +#define IRQ_MV78XX0_GPIO_0_7 56 +#define IRQ_MV78XX0_GPIO_8_15 57 +#define IRQ_MV78XX0_GPIO_16_23 58 +#define IRQ_MV78XX0_GPIO_24_31 59 +#define IRQ_MV78XX0_DB_IN 60 +#define IRQ_MV78XX0_DB_OUT 61 + +/* + * MV78XX0 General Purpose Pins + */ +#define IRQ_MV78XX0_GPIO_START 64 +#define NR_GPIO_IRQS GPIO_MAX + +#define NR_IRQS (IRQ_MV78XX0_GPIO_START + NR_GPIO_IRQS) + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/memory.h b/include/asm-arm/arch-mv78xx0/memory.h new file mode 100644 index 00000000000..721a6b185b9 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/memory.h @@ -0,0 +1,14 @@ +/* + * include/asm-arm/arch-mv78xx0/memory.h + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +#define PHYS_OFFSET UL(0x00000000) + +#define __virt_to_bus(x) __virt_to_phys(x) +#define __bus_to_virt(x) __phys_to_virt(x) + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/mv78xx0.h b/include/asm-arm/arch-mv78xx0/mv78xx0.h new file mode 100644 index 00000000000..9f5d83c73fa --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/mv78xx0.h @@ -0,0 +1,126 @@ +/* + * include/asm-arm/arch-mv78xx0/mv78xx0.h + * + * Generic definitions for Marvell MV78xx0 SoC flavors: + * MV781x0 and MV782x0. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_MV78XX0_H +#define __ASM_ARCH_MV78XX0_H + +/* + * Marvell MV78xx0 address maps. + * + * phys + * c0000000 PCIe Memory space + * f0800000 PCIe #0 I/O space + * f0900000 PCIe #1 I/O space + * f0a00000 PCIe #2 I/O space + * f0b00000 PCIe #3 I/O space + * f0c00000 PCIe #4 I/O space + * f0d00000 PCIe #5 I/O space + * f0e00000 PCIe #6 I/O space + * f0f00000 PCIe #7 I/O space + * f1000000 on-chip peripheral registers + * + * virt phys size + * fe400000 f102x000 16K core-specific peripheral registers + * fe700000 f0800000 1M PCIe #0 I/O space + * fe800000 f0900000 1M PCIe #1 I/O space + * fe900000 f0a00000 1M PCIe #2 I/O space + * fea00000 f0b00000 1M PCIe #3 I/O space + * feb00000 f0c00000 1M PCIe #4 I/O space + * fec00000 f0d00000 1M PCIe #5 I/O space + * fed00000 f0e00000 1M PCIe #6 I/O space + * fee00000 f0f00000 1M PCIe #7 I/O space + * fef00000 f1000000 1M on-chip peripheral registers + */ +#define MV78XX0_CORE0_REGS_PHYS_BASE 0xf1020000 +#define MV78XX0_CORE1_REGS_PHYS_BASE 0xf1024000 +#define MV78XX0_CORE_REGS_VIRT_BASE 0xfe400000 +#define MV78XX0_CORE_REGS_SIZE SZ_16K + +#define MV78XX0_PCIE_IO_PHYS_BASE(i) (0xf0800000 + ((i) << 20)) +#define MV78XX0_PCIE_IO_VIRT_BASE(i) (0xfe700000 + ((i) << 20)) +#define MV78XX0_PCIE_IO_SIZE SZ_1M + +#define MV78XX0_REGS_PHYS_BASE 0xf1000000 +#define MV78XX0_REGS_VIRT_BASE 0xfef00000 +#define MV78XX0_REGS_SIZE SZ_1M + +#define MV78XX0_PCIE_MEM_PHYS_BASE 0xc0000000 +#define MV78XX0_PCIE_MEM_SIZE 0x30000000 + +/* + * Core-specific peripheral registers. + */ +#define BRIDGE_VIRT_BASE (MV78XX0_CORE_REGS_VIRT_BASE) +#define CPU_CONTROL (BRIDGE_VIRT_BASE | 0x0104) +#define L2_WRITETHROUGH 0x00020000 +#define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108) +#define SOFT_RESET_OUT_EN 0x00000004 +#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c) +#define SOFT_RESET 0x00000001 +#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE | 0x0110) +#define BRIDGE_MASK (BRIDGE_VIRT_BASE | 0x0114) +#define BRIDGE_INT_TIMER0 0x0002 +#define BRIDGE_INT_TIMER1 0x0004 +#define BRIDGE_INT_TIMER1_CLR (~0x0004) +#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0200) +#define IRQ_CAUSE_LOW_OFF 0x0004 +#define IRQ_CAUSE_HIGH_OFF 0x0008 +#define IRQ_MASK_LOW_OFF 0x0010 +#define IRQ_MASK_HIGH_OFF 0x0014 +#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300) + +/* + * Register Map + */ +#define DDR_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x00000) +#define DDR_WINDOW_CPU0_BASE (DDR_VIRT_BASE | 0x1500) +#define DDR_WINDOW_CPU1_BASE (DDR_VIRT_BASE | 0x1700) + +#define DEV_BUS_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x10000) +#define DEV_BUS_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x10000) +#define SAMPLE_AT_RESET_LOW (DEV_BUS_VIRT_BASE | 0x0030) +#define SAMPLE_AT_RESET_HIGH (DEV_BUS_VIRT_BASE | 0x0034) +#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000) +#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000) +#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100) +#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2100) +#define UART2_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2200) +#define UART2_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2200) +#define UART3_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2300) +#define UART3_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2300) + +#define GE10_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x30000) +#define GE11_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x34000) + +#define PCIE00_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x40000) +#define PCIE01_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x44000) +#define PCIE02_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x48000) +#define PCIE03_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x4c000) + +#define USB0_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x50000) +#define USB1_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x51000) +#define USB2_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x52000) + +#define GE00_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x70000) +#define GE01_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0x74000) + +#define PCIE10_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x80000) +#define PCIE11_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x84000) +#define PCIE12_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x88000) +#define PCIE13_VIRT_BASE (MV78XX0_REGS_VIRT_BASE | 0x8c000) + +#define SATA_PHYS_BASE (MV78XX0_REGS_PHYS_BASE | 0xa0000) + + +#define GPIO_MAX 32 + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/system.h b/include/asm-arm/arch-mv78xx0/system.h new file mode 100644 index 00000000000..7eb47d376db --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/system.h @@ -0,0 +1,37 @@ +/* + * include/asm-arm/arch-mv78xx0/system.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include +#include + +static inline void arch_idle(void) +{ + cpu_do_idle(); +} + +static inline void arch_reset(char mode) +{ + /* + * Enable soft reset to assert RSTOUTn. + */ + writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK); + + /* + * Assert soft reset. + */ + writel(SOFT_RESET, SYSTEM_SOFT_RESET); + + while (1) + ; +} + + +#endif diff --git a/include/asm-arm/arch-mv78xx0/timex.h b/include/asm-arm/arch-mv78xx0/timex.h new file mode 100644 index 00000000000..a854b1ccbd0 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/timex.h @@ -0,0 +1,9 @@ +/* + * include/asm-arm/arch-mv78xx0/timex.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#define CLOCK_TICK_RATE (100 * HZ) diff --git a/include/asm-arm/arch-mv78xx0/uncompress.h b/include/asm-arm/arch-mv78xx0/uncompress.h new file mode 100644 index 00000000000..3bfe0a293ef --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/uncompress.h @@ -0,0 +1,47 @@ +/* + * include/asm-arm/arch-mv78xx0/uncompress.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include + +#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE) + +static void putc(const char c) +{ + unsigned char *base = SERIAL_BASE; + int i; + + for (i = 0; i < 0x1000; i++) { + if (base[UART_LSR << 2] & UART_LSR_THRE) + break; + barrier(); + } + + base[UART_TX << 2] = c; +} + +static void flush(void) +{ + unsigned char *base = SERIAL_BASE; + unsigned char mask; + int i; + + mask = UART_LSR_TEMT | UART_LSR_THRE; + + for (i = 0; i < 0x1000; i++) { + if ((base[UART_LSR << 2] & mask) == mask) + break; + barrier(); + } +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/include/asm-arm/arch-mv78xx0/vmalloc.h b/include/asm-arm/arch-mv78xx0/vmalloc.h new file mode 100644 index 00000000000..f2c51219757 --- /dev/null +++ b/include/asm-arm/arch-mv78xx0/vmalloc.h @@ -0,0 +1,5 @@ +/* + * include/asm-arm/arch-mv78xx0/vmalloc.h + */ + +#define VMALLOC_END 0xfe000000 -- cgit v1.2.3 From 395a59d0f8e86bb39cd700c3d185d30c670bb958 Mon Sep 17 00:00:00 2001 From: Abhishek Sagar Date: Sat, 21 Jun 2008 23:47:27 +0530 Subject: ftrace: store mcount address in rec->ip Record the address of the mcount call-site. Currently all archs except sparc64 record the address of the instruction following the mcount call-site. Some general cleanups are entailed. Storing mcount addresses in rec->ip enables looking them up in the kprobe hash table later on to check if they're kprobe'd. Signed-off-by: Abhishek Sagar Cc: davem@davemloft.net Cc: Steven Rostedt Signed-off-by: Ingo Molnar --- include/asm-arm/ftrace.h | 14 ++++++++++++++ 1 file changed, 14 insertions(+) create mode 100644 include/asm-arm/ftrace.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/ftrace.h b/include/asm-arm/ftrace.h new file mode 100644 index 00000000000..584ef9a8e5a --- /dev/null +++ b/include/asm-arm/ftrace.h @@ -0,0 +1,14 @@ +#ifndef _ASM_ARM_FTRACE +#define _ASM_ARM_FTRACE + +#ifdef CONFIG_FTRACE +#define MCOUNT_ADDR ((long)(mcount)) +#define MCOUNT_INSN_SIZE 4 /* sizeof mcount call */ + +#ifndef __ASSEMBLY__ +extern void mcount(void); +#endif + +#endif + +#endif /* _ASM_ARM_FTRACE */ -- cgit v1.2.3 From f6dd9fa5a75a3dae16c6843e74e56bf75be51c7c Mon Sep 17 00:00:00 2001 From: Jens Axboe Date: Tue, 10 Jun 2008 20:48:30 +0200 Subject: arm: convert to generic helpers for IPI function calls This converts arm to use the new helpers for smp_call_function() and friends, and adds support for smp_call_function_single(). Fixups and testing done by Catalin Marinas Cc: Russell King Signed-off-by: Jens Axboe --- include/asm-arm/smp.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/smp.h b/include/asm-arm/smp.h index af99636db40..7fffa2404b8 100644 --- a/include/asm-arm/smp.h +++ b/include/asm-arm/smp.h @@ -101,6 +101,9 @@ extern void platform_cpu_die(unsigned int cpu); extern int platform_cpu_kill(unsigned int cpu); extern void platform_cpu_enable(unsigned int cpu); +extern void arch_send_call_function_single_ipi(int cpu); +extern void arch_send_call_function_ipi(cpumask_t mask); + /* * Local timer interrupt handling function (can be IPI'ed). */ -- cgit v1.2.3 From 1338760329c586e0141831099e15f5c336dd9c1d Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Mon, 23 Jun 2008 01:05:08 -1100 Subject: [ARM] Kirkwood: support L2 writeback mode This patch allows booting Kirkwood with the L2 in writeback mode, by reading the WT override bit from the L2 config register and passing that into the Feroceon L2 init routine, instead of assuming that the WT override bit will always be set Signed-off-by: Saeed Bishara Signed-off-by: Lennert Buytenhek --- include/asm-arm/arch-kirkwood/kirkwood.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-kirkwood/kirkwood.h b/include/asm-arm/arch-kirkwood/kirkwood.h index 520250dbd8a..bb31b315c35 100644 --- a/include/asm-arm/arch-kirkwood/kirkwood.h +++ b/include/asm-arm/arch-kirkwood/kirkwood.h @@ -49,7 +49,6 @@ #define BRIDGE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x20000) #define CPU_CONTROL (BRIDGE_VIRT_BASE | 0x0104) #define CPU_RESET 0x00000002 -//#define L2_WRITETHROUGH 0x00020000 #define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108) #define SOFT_RESET_OUT_EN 0x00000004 #define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c) @@ -65,6 +64,8 @@ #define IRQ_CAUSE_HIGH_OFF 0x0010 #define IRQ_MASK_HIGH_OFF 0x0014 #define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300) +#define L2_CONFIG_REG (BRIDGE_VIRT_BASE | 0x0128) +#define L2_WRITETHROUGH 0x00000010 /* * Register Map -- cgit v1.2.3 From f4db56ffd43a810424866fac6de9a32486415316 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Sun, 4 May 2008 19:25:52 -1100 Subject: [MTD] orion_nand: add chip_delay parameter MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Some SoCs need a different chip_delay value. Signed-off-by: Saeed Bishara Acked-by: Jörn Engel Signed-off-by: Lennert Buytenhek Signed-off-by: Nicolas Pitre --- include/asm-arm/plat-orion/orion_nand.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-orion/orion_nand.h b/include/asm-arm/plat-orion/orion_nand.h index ffd3852a0dd..ad4ce94c199 100644 --- a/include/asm-arm/plat-orion/orion_nand.h +++ b/include/asm-arm/plat-orion/orion_nand.h @@ -18,6 +18,7 @@ struct orion_nand_data { u8 ale; /* address line number connected to ALE */ u8 cle; /* address line number connected to CLE */ u8 width; /* buswidth */ + u8 chip_delay; }; -- cgit v1.2.3 From 3fddd09e59cf49dc339e2de74d31a76c1f7f172f Mon Sep 17 00:00:00 2001 From: Richard Woodruff Date: Thu, 3 Jul 2008 12:24:30 +0300 Subject: ARM: OMAP: DMTimer: Optimize by adding load and start This patch optimizes the timer load and start sequence. By combining the load and start a needless posted wait can be removed from the system timer execution path. * Before patch register writes are taking up .078% @ 500MHz during idle. Address |total |min |max |avr |count|ratio% old\process\default_idle|7.369s |0.0us|999.902ms|14.477ms|509. |62.661% ld\Global\cpu_v7_do_idle|4.265s |0.0us|375.786ms|24.374ms|175. |36.270% (UNKNOWN)|17.503ms|0.us|531.080us|5.119us|3419. |0.148% r\omap_dm_timer_set_load|8.135ms|0.0us|79.887us|15.065us|540. |0.069% <-- \vmlinux-old\Global\_end|2.023ms|0.0us|4.000us|0.560us|3613. |0.017% -old\Global\__raw_readsw|1.962ms|0.0us|108.610us|9.167us|214. |0.016% old\smc91x\smc_interrupt|1.353ms|0.0us|10.212us|2.348us|576. |0.011% s/namei\__link_path_walk|1.161ms|0.0us|4.310us|0.762us| 1524. |0.009% \omap_dm_timer_write_reg|1.085ms|0.0us|126.150us|2.153us|504. |0.009% <-- * After patch timer functions do not show up in top listings for long captures. Signed-off-by: Richard Woodruff Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/dmtimer.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/dmtimer.h b/include/asm-arm/arch-omap/dmtimer.h index fefb276ed40..02b29e8437a 100644 --- a/include/asm-arm/arch-omap/dmtimer.h +++ b/include/asm-arm/arch-omap/dmtimer.h @@ -66,6 +66,7 @@ void omap_dm_timer_stop(struct omap_dm_timer *timer); void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source); void omap_dm_timer_set_load(struct omap_dm_timer *timer, int autoreload, unsigned int value); +void omap_dm_timer_set_load_start(struct omap_dm_timer *timer, int autoreload, unsigned int value); void omap_dm_timer_set_match(struct omap_dm_timer *timer, int enable, unsigned int match); void omap_dm_timer_set_pwm(struct omap_dm_timer *timer, int def_on, int toggle, int trigger); void omap_dm_timer_set_prescaler(struct omap_dm_timer *timer, int prescaler); -- cgit v1.2.3 From 4a79acdc784c315d9c436ba2315d08f8f53b8adf Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Thu, 3 Jul 2008 12:24:31 +0300 Subject: ARM: OMAP: Add OMAP3430 base defines Add symbolic constants for OMAP3430 base addresses; include that file in hardware.h. Signed-off-by: Paul Walmsley Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/hardware.h | 1 + include/asm-arm/arch-omap/omap34xx.h | 72 ++++++++++++++++++++++++++++++++++++ 2 files changed, 73 insertions(+) create mode 100644 include/asm-arm/arch-omap/omap34xx.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/hardware.h b/include/asm-arm/arch-omap/hardware.h index 91d85b3417b..45fdfccbd5d 100644 --- a/include/asm-arm/arch-omap/hardware.h +++ b/include/asm-arm/arch-omap/hardware.h @@ -284,6 +284,7 @@ #include "omap1510.h" #include "omap24xx.h" #include "omap16xx.h" +#include "omap34xx.h" #ifndef __ASSEMBLER__ diff --git a/include/asm-arm/arch-omap/omap34xx.h b/include/asm-arm/arch-omap/omap34xx.h new file mode 100644 index 00000000000..aa30c6d10ab --- /dev/null +++ b/include/asm-arm/arch-omap/omap34xx.h @@ -0,0 +1,72 @@ +/* + * include/asm-arm/arch-omap/omap34xx.h + * + * This file contains the processor specific definitions of the TI OMAP34XX. + * + * Copyright (C) 2007 Texas Instruments. + * Copyright (C) 2007 Nokia Corporation. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_OMAP34XX_H +#define __ASM_ARCH_OMAP34XX_H + +/* + * Please place only base defines here and put the rest in device + * specific headers. + */ + +#define L4_34XX_BASE 0x48000000 +#define L4_WK_34XX_BASE 0x48300000 +#define L4_WK_OMAP_BASE L4_WK_34XX_BASE +#define L4_PER_34XX_BASE 0x49000000 +#define L4_PER_OMAP_BASE L4_PER_34XX_BASE +#define L4_EMU_34XX_BASE 0x54000000 +#define L4_EMU_BASE L4_EMU_34XX_BASE +#define L3_34XX_BASE 0x68000000 +#define L3_OMAP_BASE L3_34XX_BASE + +#define OMAP3430_32KSYNCT_BASE 0x48320000 +#define OMAP3430_CM_BASE 0x48004800 +#define OMAP3430_PRM_BASE 0x48306800 +#define OMAP343X_SMS_BASE 0x6C000000 +#define OMAP343X_SDRC_BASE 0x6D000000 +#define OMAP34XX_GPMC_BASE 0x6E000000 +#define OMAP343X_SCM_BASE 0x48002000 +#define OMAP343X_CTRL_BASE OMAP343X_SCM_BASE + +#define OMAP34XX_IC_BASE 0x48200000 +#define OMAP34XX_IVA_INTC_BASE 0x40000000 +#define OMAP34XX_HSUSB_OTG_BASE (L4_34XX_BASE + 0xAB000) +#define OMAP34XX_HSUSB_HOST_BASE (L4_34XX_BASE + 0x64000) +#define OMAP34XX_USBTLL_BASE (L4_34XX_BASE + 0x62000) + + +#if defined(CONFIG_ARCH_OMAP3430) + +#define OMAP2_32KSYNCT_BASE OMAP3430_32KSYNCT_BASE +#define OMAP2_CM_BASE OMAP3430_CM_BASE +#define OMAP2_PRM_BASE OMAP3430_PRM_BASE +#define OMAP2_VA_IC_BASE IO_ADDRESS(OMAP34XX_IC_BASE) + +#endif + +#define OMAP34XX_DSP_BASE 0x58000000 +#define OMAP34XX_DSP_MEM_BASE (OMAP34XX_DSP_BASE + 0x0) +#define OMAP34XX_DSP_IPI_BASE (OMAP34XX_DSP_BASE + 0x1000000) +#define OMAP34XX_DSP_MMU_BASE (OMAP34XX_DSP_BASE + 0x2000000) +#endif /* __ASM_ARCH_OMAP34XX_H */ + -- cgit v1.2.3 From 4d96372e6daae89166fed7883ee092dc8db80b21 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:31 +0300 Subject: ARM: OMAP: DMA: Make channels dynamic for multi-boot Make DMA channels dynamic for multi-boot Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/dma.h | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/dma.h b/include/asm-arm/arch-omap/dma.h index 24acf090030..46fe5a40a25 100644 --- a/include/asm-arm/arch-omap/dma.h +++ b/include/asm-arm/arch-omap/dma.h @@ -68,9 +68,10 @@ #define OMAP_DMA4_CAPS_3 (OMAP_DMA4_BASE + 0x70) #define OMAP_DMA4_CAPS_4 (OMAP_DMA4_BASE + 0x74) -#ifdef CONFIG_ARCH_OMAP1 +#define OMAP1_LOGICAL_DMA_CH_COUNT 17 +#define OMAP_DMA4_LOGICAL_DMA_CH_COUNT 32 /* REVISIT: Is this 32 + 2? */ -#define OMAP_LOGICAL_DMA_CH_COUNT 17 +#ifdef CONFIG_ARCH_OMAP1 /* Common channel specific registers for omap1 */ #define OMAP_DMA_CSDP_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x00) @@ -89,8 +90,6 @@ #else -#define OMAP_LOGICAL_DMA_CH_COUNT 32 /* REVISIT: Is this 32 + 2? */ - /* Common channel specific registers for omap2 */ #define OMAP_DMA_CCR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x80) #define OMAP_DMA_CLNK_CTRL_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x84) -- cgit v1.2.3 From 0499bdeb1dec30325aa282a83f9374fa849aa01c Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:36 +0300 Subject: ARM: OMAP: DMA: Remove __REG access Remove __REG access in DMA code, use dma_read/write instead: - dynamically set the omap_dma_base based on the omap type - omap_read/write becomes dma_read/write - dma channel registers are read with dma_ch_read/write Cc: David Brownell Cc: linux-usb@vger.kernel.org Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/dma.h | 210 +++++++++++++++++++++++----------------- 1 file changed, 120 insertions(+), 90 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/dma.h b/include/asm-arm/arch-omap/dma.h index 46fe5a40a25..d188100f8f4 100644 --- a/include/asm-arm/arch-omap/dma.h +++ b/include/asm-arm/arch-omap/dma.h @@ -22,107 +22,128 @@ #define __ASM_ARCH_DMA_H /* Hardware registers for omap1 */ -#define OMAP_DMA_BASE (0xfffed800) -#define OMAP_DMA_GCR (OMAP_DMA_BASE + 0x400) -#define OMAP_DMA_GSCR (OMAP_DMA_BASE + 0x404) -#define OMAP_DMA_GRST (OMAP_DMA_BASE + 0x408) -#define OMAP_DMA_HW_ID (OMAP_DMA_BASE + 0x442) -#define OMAP_DMA_PCH2_ID (OMAP_DMA_BASE + 0x444) -#define OMAP_DMA_PCH0_ID (OMAP_DMA_BASE + 0x446) -#define OMAP_DMA_PCH1_ID (OMAP_DMA_BASE + 0x448) -#define OMAP_DMA_PCHG_ID (OMAP_DMA_BASE + 0x44a) -#define OMAP_DMA_PCHD_ID (OMAP_DMA_BASE + 0x44c) -#define OMAP_DMA_CAPS_0_U (OMAP_DMA_BASE + 0x44e) -#define OMAP_DMA_CAPS_0_L (OMAP_DMA_BASE + 0x450) -#define OMAP_DMA_CAPS_1_U (OMAP_DMA_BASE + 0x452) -#define OMAP_DMA_CAPS_1_L (OMAP_DMA_BASE + 0x454) -#define OMAP_DMA_CAPS_2 (OMAP_DMA_BASE + 0x456) -#define OMAP_DMA_CAPS_3 (OMAP_DMA_BASE + 0x458) -#define OMAP_DMA_CAPS_4 (OMAP_DMA_BASE + 0x45a) -#define OMAP_DMA_PCH2_SR (OMAP_DMA_BASE + 0x460) -#define OMAP_DMA_PCH0_SR (OMAP_DMA_BASE + 0x480) -#define OMAP_DMA_PCH1_SR (OMAP_DMA_BASE + 0x482) -#define OMAP_DMA_PCHD_SR (OMAP_DMA_BASE + 0x4c0) - -/* Hardware registers for omap2 */ -#if defined(CONFIG_ARCH_OMAP3) -#define OMAP_DMA4_BASE (L4_34XX_BASE + 0x56000) -#else /* CONFIG_ARCH_OMAP2 */ -#define OMAP_DMA4_BASE (L4_24XX_BASE + 0x56000) -#endif - -#define OMAP_DMA4_REVISION (OMAP_DMA4_BASE + 0x00) -#define OMAP_DMA4_GCR_REG (OMAP_DMA4_BASE + 0x78) -#define OMAP_DMA4_IRQSTATUS_L0 (OMAP_DMA4_BASE + 0x08) -#define OMAP_DMA4_IRQSTATUS_L1 (OMAP_DMA4_BASE + 0x0c) -#define OMAP_DMA4_IRQSTATUS_L2 (OMAP_DMA4_BASE + 0x10) -#define OMAP_DMA4_IRQSTATUS_L3 (OMAP_DMA4_BASE + 0x14) -#define OMAP_DMA4_IRQENABLE_L0 (OMAP_DMA4_BASE + 0x18) -#define OMAP_DMA4_IRQENABLE_L1 (OMAP_DMA4_BASE + 0x1c) -#define OMAP_DMA4_IRQENABLE_L2 (OMAP_DMA4_BASE + 0x20) -#define OMAP_DMA4_IRQENABLE_L3 (OMAP_DMA4_BASE + 0x24) -#define OMAP_DMA4_SYSSTATUS (OMAP_DMA4_BASE + 0x28) -#define OMAP_DMA4_OCP_SYSCONFIG (OMAP_DMA4_BASE + 0x2c) -#define OMAP_DMA4_CAPS_0 (OMAP_DMA4_BASE + 0x64) -#define OMAP_DMA4_CAPS_2 (OMAP_DMA4_BASE + 0x6c) -#define OMAP_DMA4_CAPS_3 (OMAP_DMA4_BASE + 0x70) -#define OMAP_DMA4_CAPS_4 (OMAP_DMA4_BASE + 0x74) +#define OMAP1_DMA_BASE (0xfffed800) + +#define OMAP1_DMA_GCR 0x400 +#define OMAP1_DMA_GSCR 0x404 +#define OMAP1_DMA_GRST 0x408 +#define OMAP1_DMA_HW_ID 0x442 +#define OMAP1_DMA_PCH2_ID 0x444 +#define OMAP1_DMA_PCH0_ID 0x446 +#define OMAP1_DMA_PCH1_ID 0x448 +#define OMAP1_DMA_PCHG_ID 0x44a +#define OMAP1_DMA_PCHD_ID 0x44c +#define OMAP1_DMA_CAPS_0_U 0x44e +#define OMAP1_DMA_CAPS_0_L 0x450 +#define OMAP1_DMA_CAPS_1_U 0x452 +#define OMAP1_DMA_CAPS_1_L 0x454 +#define OMAP1_DMA_CAPS_2 0x456 +#define OMAP1_DMA_CAPS_3 0x458 +#define OMAP1_DMA_CAPS_4 0x45a +#define OMAP1_DMA_PCH2_SR 0x460 +#define OMAP1_DMA_PCH0_SR 0x480 +#define OMAP1_DMA_PCH1_SR 0x482 +#define OMAP1_DMA_PCHD_SR 0x4c0 + +/* Hardware registers for omap2 and omap3 */ +#define OMAP24XX_DMA4_BASE (L4_24XX_BASE + 0x56000) +#define OMAP34XX_DMA4_BASE (L4_34XX_BASE + 0x56000) + +#define OMAP_DMA4_REVISION 0x00 +#define OMAP_DMA4_GCR 0x78 +#define OMAP_DMA4_IRQSTATUS_L0 0x08 +#define OMAP_DMA4_IRQSTATUS_L1 0x0c +#define OMAP_DMA4_IRQSTATUS_L2 0x10 +#define OMAP_DMA4_IRQSTATUS_L3 0x14 +#define OMAP_DMA4_IRQENABLE_L0 0x18 +#define OMAP_DMA4_IRQENABLE_L1 0x1c +#define OMAP_DMA4_IRQENABLE_L2 0x20 +#define OMAP_DMA4_IRQENABLE_L3 0x24 +#define OMAP_DMA4_SYSSTATUS 0x28 +#define OMAP_DMA4_OCP_SYSCONFIG 0x2c +#define OMAP_DMA4_CAPS_0 0x64 +#define OMAP_DMA4_CAPS_2 0x6c +#define OMAP_DMA4_CAPS_3 0x70 +#define OMAP_DMA4_CAPS_4 0x74 #define OMAP1_LOGICAL_DMA_CH_COUNT 17 #define OMAP_DMA4_LOGICAL_DMA_CH_COUNT 32 /* REVISIT: Is this 32 + 2? */ -#ifdef CONFIG_ARCH_OMAP1 - /* Common channel specific registers for omap1 */ -#define OMAP_DMA_CSDP_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x00) -#define OMAP_DMA_CCR_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x02) -#define OMAP_DMA_CICR_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x04) -#define OMAP_DMA_CSR_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x06) -#define OMAP_DMA_CEN_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x10) -#define OMAP_DMA_CFN_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x12) -#define OMAP_DMA_CSFI_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x14) -#define OMAP_DMA_CSEI_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x16) -#define OMAP_DMA_CSAC_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x18) -#define OMAP_DMA_CDAC_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x1a) -#define OMAP_DMA_CDEI_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x1c) -#define OMAP_DMA_CDFI_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x1e) -#define OMAP_DMA_CLNK_CTRL_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x28) - -#else +#define OMAP1_DMA_CH_BASE(n) (0x40 * (n) + 0x00) +#define OMAP1_DMA_CSDP(n) (0x40 * (n) + 0x00) +#define OMAP1_DMA_CCR(n) (0x40 * (n) + 0x02) +#define OMAP1_DMA_CICR(n) (0x40 * (n) + 0x04) +#define OMAP1_DMA_CSR(n) (0x40 * (n) + 0x06) +#define OMAP1_DMA_CEN(n) (0x40 * (n) + 0x10) +#define OMAP1_DMA_CFN(n) (0x40 * (n) + 0x12) +#define OMAP1_DMA_CSFI(n) (0x40 * (n) + 0x14) +#define OMAP1_DMA_CSEI(n) (0x40 * (n) + 0x16) +#define OMAP1_DMA_CPC(n) (0x40 * (n) + 0x18) /* 15xx only */ +#define OMAP1_DMA_CSAC(n) (0x40 * (n) + 0x18) +#define OMAP1_DMA_CDAC(n) (0x40 * (n) + 0x1a) +#define OMAP1_DMA_CDEI(n) (0x40 * (n) + 0x1c) +#define OMAP1_DMA_CDFI(n) (0x40 * (n) + 0x1e) +#define OMAP1_DMA_CLNK_CTRL(n) (0x40 * (n) + 0x28) /* Common channel specific registers for omap2 */ -#define OMAP_DMA_CCR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x80) -#define OMAP_DMA_CLNK_CTRL_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x84) -#define OMAP_DMA_CICR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x88) -#define OMAP_DMA_CSR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x8c) -#define OMAP_DMA_CSDP_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x90) -#define OMAP_DMA_CEN_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x94) -#define OMAP_DMA_CFN_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x98) -#define OMAP_DMA_CSEI_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xa4) -#define OMAP_DMA_CSFI_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xa8) -#define OMAP_DMA_CDEI_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xac) -#define OMAP_DMA_CDFI_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xb0) -#define OMAP_DMA_CSAC_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xb4) -#define OMAP_DMA_CDAC_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xb8) - -#endif +#define OMAP_DMA4_CH_BASE(n) (0x60 * (n) + 0x80) +#define OMAP_DMA4_CCR(n) (0x60 * (n) + 0x80) +#define OMAP_DMA4_CLNK_CTRL(n) (0x60 * (n) + 0x84) +#define OMAP_DMA4_CICR(n) (0x60 * (n) + 0x88) +#define OMAP_DMA4_CSR(n) (0x60 * (n) + 0x8c) +#define OMAP_DMA4_CSDP(n) (0x60 * (n) + 0x90) +#define OMAP_DMA4_CEN(n) (0x60 * (n) + 0x94) +#define OMAP_DMA4_CFN(n) (0x60 * (n) + 0x98) +#define OMAP_DMA4_CSEI(n) (0x60 * (n) + 0xa4) +#define OMAP_DMA4_CSFI(n) (0x60 * (n) + 0xa8) +#define OMAP_DMA4_CDEI(n) (0x60 * (n) + 0xac) +#define OMAP_DMA4_CDFI(n) (0x60 * (n) + 0xb0) +#define OMAP_DMA4_CSAC(n) (0x60 * (n) + 0xb4) +#define OMAP_DMA4_CDAC(n) (0x60 * (n) + 0xb8) /* Channel specific registers only on omap1 */ -#define OMAP1_DMA_CSSA_L_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x08) -#define OMAP1_DMA_CSSA_U_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x0a) -#define OMAP1_DMA_CDSA_L_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x0c) -#define OMAP1_DMA_CDSA_U_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x0e) -#define OMAP1_DMA_COLOR_L_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x20) -#define OMAP1_DMA_CCR2_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x24) -#define OMAP1_DMA_COLOR_U_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x22) -#define OMAP1_DMA_LCH_CTRL_REG(n) __REG16(OMAP_DMA_BASE + 0x40 * (n) + 0x2a) +#define OMAP1_DMA_CSSA_L(n) (0x40 * (n) + 0x08) +#define OMAP1_DMA_CSSA_U(n) (0x40 * (n) + 0x0a) +#define OMAP1_DMA_CDSA_L(n) (0x40 * (n) + 0x0c) +#define OMAP1_DMA_CDSA_U(n) (0x40 * (n) + 0x0e) +#define OMAP1_DMA_COLOR_L(n) (0x40 * (n) + 0x20) +#define OMAP1_DMA_COLOR_U(n) (0x40 * (n) + 0x22) +#define OMAP1_DMA_CCR2(n) (0x40 * (n) + 0x24) +#define OMAP1_DMA_LCH_CTRL(n) (0x40 * (n) + 0x2a) /* not on 15xx */ +#define OMAP1_DMA_CCEN(n) 0 +#define OMAP1_DMA_CCFN(n) 0 /* Channel specific registers only on omap2 */ -#define OMAP2_DMA_CSSA_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0x9c) -#define OMAP2_DMA_CDSA_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xa0) -#define OMAP2_DMA_CCEN_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xbc) -#define OMAP2_DMA_CCFN_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xc0) -#define OMAP2_DMA_COLOR_REG(n) __REG32(OMAP_DMA4_BASE + 0x60 * (n) + 0xc4) +#define OMAP_DMA4_CSSA(n) (0x60 * (n) + 0x9c) +#define OMAP_DMA4_CDSA(n) (0x60 * (n) + 0xa0) +#define OMAP_DMA4_CCEN(n) (0x60 * (n) + 0xbc) +#define OMAP_DMA4_CCFN(n) (0x60 * (n) + 0xc0) +#define OMAP_DMA4_COLOR(n) (0x60 * (n) + 0xc4) + +/* Dummy defines to keep multi-omap compiles happy */ +#define OMAP1_DMA_REVISION 0 +#define OMAP1_DMA_IRQSTATUS_L0 0 +#define OMAP1_DMA_IRQENABLE_L0 0 +#define OMAP1_DMA_OCP_SYSCONFIG 0 +#define OMAP_DMA4_HW_ID 0 +#define OMAP_DMA4_CAPS_0_L 0 +#define OMAP_DMA4_CAPS_0_U 0 +#define OMAP_DMA4_CAPS_1_L 0 +#define OMAP_DMA4_CAPS_1_U 0 +#define OMAP_DMA4_GSCR 0 +#define OMAP_DMA4_CPC(n) 0 + +#define OMAP_DMA4_LCH_CTRL(n) 0 +#define OMAP_DMA4_COLOR_L(n) 0 +#define OMAP_DMA4_COLOR_U(n) 0 +#define OMAP_DMA4_CCR2(n) 0 +#define OMAP1_DMA_CSSA(n) 0 +#define OMAP1_DMA_CDSA(n) 0 +#define OMAP_DMA4_CSSA_L(n) 0 +#define OMAP_DMA4_CSSA_U(n) 0 +#define OMAP_DMA4_CDSA_L(n) 0 +#define OMAP_DMA4_CDSA_U(n) 0 /*----------------------------------------------------------------------------*/ @@ -369,6 +390,13 @@ enum omap_dma_write_mode { OMAP_DMA_WRITE_LAST_NON_POSTED }; +enum omap_dma_channel_mode { + OMAP_DMA_LCH_2D = 0, + OMAP_DMA_LCH_G, + OMAP_DMA_LCH_P, + OMAP_DMA_LCH_PD +}; + struct omap_dma_channel_params { int data_type; /* data type 8,16,32 */ int elem_count; /* number of elements in a frame */ @@ -417,6 +445,7 @@ extern void omap_set_dma_transfer_params(int lch, int data_type, extern void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color); extern void omap_set_dma_write_mode(int lch, enum omap_dma_write_mode mode); +extern void omap_set_dma_channel_mode(int lch, enum omap_dma_channel_mode mode); extern void omap_set_dma_src_params(int lch, int src_port, int src_amode, unsigned long src_start, @@ -447,6 +476,7 @@ extern dma_addr_t omap_get_dma_src_pos(int lch); extern dma_addr_t omap_get_dma_dst_pos(int lch); extern int omap_get_dma_src_addr_counter(int lch); extern void omap_clear_dma(int lch); +extern int omap_get_dma_active_status(int lch); extern int omap_dma_running(void); extern void omap_dma_set_global_params(int arb_rate, int max_fifo_depth, int tparams); -- cgit v1.2.3 From 97b7f715589fb997e430c6aa824abbd9fd5ed42d Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:37 +0300 Subject: ARM: OMAP: DMA: Clean-up code DMA clean-up, mostly checkpatch.pl fixes. Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/dma.h | 161 +++++++++++++++++++++++++--------------- 1 file changed, 103 insertions(+), 58 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/dma.h b/include/asm-arm/arch-omap/dma.h index d188100f8f4..f4dcb958786 100644 --- a/include/asm-arm/arch-omap/dma.h +++ b/include/asm-arm/arch-omap/dma.h @@ -216,63 +216,98 @@ #define OMAP24XX_DMA_GPMC 4 /* S_DMA_3 */ #define OMAP24XX_DMA_GFX 5 /* S_DMA_4 */ #define OMAP24XX_DMA_DSS 6 /* S_DMA_5 */ -#define OMAP24XX_DMA_VLYNQ_TX 7 /* S_DMA_6 */ +#define OMAP242X_DMA_VLYNQ_TX 7 /* S_DMA_6 */ +#define OMAP24XX_DMA_EXT_DMAREQ2 7 /* S_DMA_6 */ #define OMAP24XX_DMA_CWT 8 /* S_DMA_7 */ #define OMAP24XX_DMA_AES_TX 9 /* S_DMA_8 */ #define OMAP24XX_DMA_AES_RX 10 /* S_DMA_9 */ #define OMAP24XX_DMA_DES_TX 11 /* S_DMA_10 */ #define OMAP24XX_DMA_DES_RX 12 /* S_DMA_11 */ #define OMAP24XX_DMA_SHA1MD5_RX 13 /* S_DMA_12 */ -#define OMAP24XX_DMA_EXT_DMAREQ2 14 /* S_DMA_13 */ -#define OMAP24XX_DMA_EXT_DMAREQ3 15 /* S_DMA_14 */ -#define OMAP24XX_DMA_EXT_DMAREQ4 16 /* S_DMA_15 */ -#define OMAP24XX_DMA_EAC_AC_RD 17 /* S_DMA_16 */ -#define OMAP24XX_DMA_EAC_AC_WR 18 /* S_DMA_17 */ -#define OMAP24XX_DMA_EAC_MD_UL_RD 19 /* S_DMA_18 */ -#define OMAP24XX_DMA_EAC_MD_UL_WR 20 /* S_DMA_19 */ -#define OMAP24XX_DMA_EAC_MD_DL_RD 21 /* S_DMA_20 */ -#define OMAP24XX_DMA_EAC_MD_DL_WR 22 /* S_DMA_21 */ -#define OMAP24XX_DMA_EAC_BT_UL_RD 23 /* S_DMA_22 */ -#define OMAP24XX_DMA_EAC_BT_UL_WR 24 /* S_DMA_23 */ -#define OMAP24XX_DMA_EAC_BT_DL_RD 25 /* S_DMA_24 */ -#define OMAP24XX_DMA_EAC_BT_DL_WR 26 /* S_DMA_25 */ +#define OMAP34XX_DMA_SHA2MD5_RX 13 /* S_DMA_12 */ +#define OMAP242X_DMA_EXT_DMAREQ2 14 /* S_DMA_13 */ +#define OMAP242X_DMA_EXT_DMAREQ3 15 /* S_DMA_14 */ +#define OMAP242X_DMA_EXT_DMAREQ4 16 /* S_DMA_15 */ +#define OMAP242X_DMA_EAC_AC_RD 17 /* S_DMA_16 */ +#define OMAP242X_DMA_EAC_AC_WR 18 /* S_DMA_17 */ +#define OMAP242X_DMA_EAC_MD_UL_RD 19 /* S_DMA_18 */ +#define OMAP242X_DMA_EAC_MD_UL_WR 20 /* S_DMA_19 */ +#define OMAP242X_DMA_EAC_MD_DL_RD 21 /* S_DMA_20 */ +#define OMAP242X_DMA_EAC_MD_DL_WR 22 /* S_DMA_21 */ +#define OMAP242X_DMA_EAC_BT_UL_RD 23 /* S_DMA_22 */ +#define OMAP242X_DMA_EAC_BT_UL_WR 24 /* S_DMA_23 */ +#define OMAP242X_DMA_EAC_BT_DL_RD 25 /* S_DMA_24 */ +#define OMAP242X_DMA_EAC_BT_DL_WR 26 /* S_DMA_25 */ +#define OMAP243X_DMA_EXT_DMAREQ3 14 /* S_DMA_13 */ +#define OMAP24XX_DMA_SPI3_TX0 15 /* S_DMA_14 */ +#define OMAP24XX_DMA_SPI3_RX0 16 /* S_DMA_15 */ +#define OMAP24XX_DMA_MCBSP3_TX 17 /* S_DMA_16 */ +#define OMAP24XX_DMA_MCBSP3_RX 18 /* S_DMA_17 */ +#define OMAP24XX_DMA_MCBSP4_TX 19 /* S_DMA_18 */ +#define OMAP24XX_DMA_MCBSP4_RX 20 /* S_DMA_19 */ +#define OMAP24XX_DMA_MCBSP5_TX 21 /* S_DMA_20 */ +#define OMAP24XX_DMA_MCBSP5_RX 22 /* S_DMA_21 */ +#define OMAP24XX_DMA_SPI3_TX1 23 /* S_DMA_22 */ +#define OMAP24XX_DMA_SPI3_RX1 24 /* S_DMA_23 */ +#define OMAP243X_DMA_EXT_DMAREQ4 25 /* S_DMA_24 */ +#define OMAP243X_DMA_EXT_DMAREQ5 26 /* S_DMA_25 */ +#define OMAP34XX_DMA_I2C3_TX 25 /* S_DMA_24 */ +#define OMAP34XX_DMA_I2C3_RX 26 /* S_DMA_25 */ #define OMAP24XX_DMA_I2C1_TX 27 /* S_DMA_26 */ #define OMAP24XX_DMA_I2C1_RX 28 /* S_DMA_27 */ #define OMAP24XX_DMA_I2C2_TX 29 /* S_DMA_28 */ #define OMAP24XX_DMA_I2C2_RX 30 /* S_DMA_29 */ -#define OMAP24XX_DMA_MCBSP1_TX 31 /* SDMA_30 */ -#define OMAP24XX_DMA_MCBSP1_RX 32 /* SDMA_31 */ -#define OMAP24XX_DMA_MCBSP2_TX 33 /* SDMA_32 */ -#define OMAP24XX_DMA_MCBSP2_RX 34 /* SDMA_33 */ -#define OMAP24XX_DMA_SPI1_TX0 35 /* SDMA_34 */ -#define OMAP24XX_DMA_SPI1_RX0 36 /* SDMA_35 */ -#define OMAP24XX_DMA_SPI1_TX1 37 /* SDMA_36 */ -#define OMAP24XX_DMA_SPI1_RX1 38 /* SDMA_37 */ -#define OMAP24XX_DMA_SPI1_TX2 39 /* SDMA_38 */ -#define OMAP24XX_DMA_SPI1_RX2 40 /* SDMA_39 */ -#define OMAP24XX_DMA_SPI1_TX3 41 /* SDMA_40 */ -#define OMAP24XX_DMA_SPI1_RX3 42 /* SDMA_41 */ -#define OMAP24XX_DMA_SPI2_TX0 43 /* SDMA_42 */ -#define OMAP24XX_DMA_SPI2_RX0 44 /* SDMA_43 */ -#define OMAP24XX_DMA_SPI2_TX1 45 /* SDMA_44 */ -#define OMAP24XX_DMA_SPI2_RX1 46 /* SDMA_45 */ - -#define OMAP24XX_DMA_UART1_TX 49 /* SDMA_48 */ -#define OMAP24XX_DMA_UART1_RX 50 /* SDMA_49 */ -#define OMAP24XX_DMA_UART2_TX 51 /* SDMA_50 */ -#define OMAP24XX_DMA_UART2_RX 52 /* SDMA_51 */ -#define OMAP24XX_DMA_UART3_TX 53 /* SDMA_52 */ -#define OMAP24XX_DMA_UART3_RX 54 /* SDMA_53 */ -#define OMAP24XX_DMA_USB_W2FC_TX0 55 /* SDMA_54 */ -#define OMAP24XX_DMA_USB_W2FC_RX0 56 /* SDMA_55 */ -#define OMAP24XX_DMA_USB_W2FC_TX1 57 /* SDMA_56 */ -#define OMAP24XX_DMA_USB_W2FC_RX1 58 /* SDMA_57 */ -#define OMAP24XX_DMA_USB_W2FC_TX2 59 /* SDMA_58 */ -#define OMAP24XX_DMA_USB_W2FC_RX2 60 /* SDMA_59 */ -#define OMAP24XX_DMA_MMC1_TX 61 /* SDMA_60 */ -#define OMAP24XX_DMA_MMC1_RX 62 /* SDMA_61 */ -#define OMAP24XX_DMA_MS 63 /* SDMA_62 */ -#define OMAP24XX_DMA_EXT_DMAREQ5 64 /* S_DMA_63 */ +#define OMAP24XX_DMA_MCBSP1_TX 31 /* S_DMA_30 */ +#define OMAP24XX_DMA_MCBSP1_RX 32 /* S_DMA_31 */ +#define OMAP24XX_DMA_MCBSP2_TX 33 /* S_DMA_32 */ +#define OMAP24XX_DMA_MCBSP2_RX 34 /* S_DMA_33 */ +#define OMAP24XX_DMA_SPI1_TX0 35 /* S_DMA_34 */ +#define OMAP24XX_DMA_SPI1_RX0 36 /* S_DMA_35 */ +#define OMAP24XX_DMA_SPI1_TX1 37 /* S_DMA_36 */ +#define OMAP24XX_DMA_SPI1_RX1 38 /* S_DMA_37 */ +#define OMAP24XX_DMA_SPI1_TX2 39 /* S_DMA_38 */ +#define OMAP24XX_DMA_SPI1_RX2 40 /* S_DMA_39 */ +#define OMAP24XX_DMA_SPI1_TX3 41 /* S_DMA_40 */ +#define OMAP24XX_DMA_SPI1_RX3 42 /* S_DMA_41 */ +#define OMAP24XX_DMA_SPI2_TX0 43 /* S_DMA_42 */ +#define OMAP24XX_DMA_SPI2_RX0 44 /* S_DMA_43 */ +#define OMAP24XX_DMA_SPI2_TX1 45 /* S_DMA_44 */ +#define OMAP24XX_DMA_SPI2_RX1 46 /* S_DMA_45 */ +#define OMAP24XX_DMA_MMC2_TX 47 /* S_DMA_46 */ +#define OMAP24XX_DMA_MMC2_RX 48 /* S_DMA_47 */ +#define OMAP24XX_DMA_UART1_TX 49 /* S_DMA_48 */ +#define OMAP24XX_DMA_UART1_RX 50 /* S_DMA_49 */ +#define OMAP24XX_DMA_UART2_TX 51 /* S_DMA_50 */ +#define OMAP24XX_DMA_UART2_RX 52 /* S_DMA_51 */ +#define OMAP24XX_DMA_UART3_TX 53 /* S_DMA_52 */ +#define OMAP24XX_DMA_UART3_RX 54 /* S_DMA_53 */ +#define OMAP24XX_DMA_USB_W2FC_TX0 55 /* S_DMA_54 */ +#define OMAP24XX_DMA_USB_W2FC_RX0 56 /* S_DMA_55 */ +#define OMAP24XX_DMA_USB_W2FC_TX1 57 /* S_DMA_56 */ +#define OMAP24XX_DMA_USB_W2FC_RX1 58 /* S_DMA_57 */ +#define OMAP24XX_DMA_USB_W2FC_TX2 59 /* S_DMA_58 */ +#define OMAP24XX_DMA_USB_W2FC_RX2 60 /* S_DMA_59 */ +#define OMAP24XX_DMA_MMC1_TX 61 /* S_DMA_60 */ +#define OMAP24XX_DMA_MMC1_RX 62 /* S_DMA_61 */ +#define OMAP24XX_DMA_MS 63 /* S_DMA_62 */ +#define OMAP242X_DMA_EXT_DMAREQ5 64 /* S_DMA_63 */ +#define OMAP243X_DMA_EXT_DMAREQ6 64 /* S_DMA_63 */ +#define OMAP34XX_DMA_EXT_DMAREQ3 64 /* S_DMA_63 */ +#define OMAP34XX_DMA_AES2_TX 65 /* S_DMA_64 */ +#define OMAP34XX_DMA_AES2_RX 66 /* S_DMA_65 */ +#define OMAP34XX_DMA_DES2_TX 67 /* S_DMA_66 */ +#define OMAP34XX_DMA_DES2_RX 68 /* S_DMA_67 */ +#define OMAP34XX_DMA_SHA1MD5_RX 69 /* S_DMA_68 */ +#define OMAP34XX_DMA_SPI4_TX0 70 /* S_DMA_69 */ +#define OMAP34XX_DMA_SPI4_RX0 71 /* S_DMA_70 */ +#define OMAP34XX_DSS_DMA0 72 /* S_DMA_71 */ +#define OMAP34XX_DSS_DMA1 73 /* S_DMA_72 */ +#define OMAP34XX_DSS_DMA2 74 /* S_DMA_73 */ +#define OMAP34XX_DSS_DMA3 75 /* S_DMA_74 */ +#define OMAP34XX_DMA_MMC3_TX 77 /* S_DMA_76 */ +#define OMAP34XX_DMA_MMC3_RX 78 /* S_DMA_77 */ +#define OMAP34XX_DMA_USIM_TX 79 /* S_DMA_78 */ +#define OMAP34XX_DMA_USIM_RX 80 /* S_DMA_79 */ /*----------------------------------------------------------------------------*/ @@ -378,6 +413,11 @@ enum omap_dma_burst_mode { OMAP_DMA_DATA_BURST_16, }; +enum end_type { + OMAP_DMA_LITTLE_ENDIAN = 0, + OMAP_DMA_BIG_ENDIAN +}; + enum omap_dma_color_mode { OMAP_DMA_COLOR_DIS = 0, OMAP_DMA_CONSTANT_FILL, @@ -403,18 +443,21 @@ struct omap_dma_channel_params { int frame_count; /* number of frames in a element */ int src_port; /* Only on OMAP1 REVISIT: Is this needed? */ - int src_amode; /* constant , post increment, indexed , double indexed */ + int src_amode; /* constant, post increment, indexed, + double indexed */ unsigned long src_start; /* source address : physical */ int src_ei; /* source element index */ int src_fi; /* source frame index */ int dst_port; /* Only on OMAP1 REVISIT: Is this needed? */ - int dst_amode; /* constant , post increment, indexed , double indexed */ + int dst_amode; /* constant, post increment, indexed, + double indexed */ unsigned long dst_start; /* source address : physical */ int dst_ei; /* source element index */ int dst_fi; /* source frame index */ - int trigger; /* trigger attached if the channel is synchronized */ + int trigger; /* trigger attached if the channel is + synchronized */ int sync_mode; /* sycn on element, frame , block or packet */ int src_or_dst_synch; /* source synch(1) or destination synch(0) */ @@ -431,8 +474,8 @@ struct omap_dma_channel_params { extern void omap_set_dma_priority(int lch, int dst_port, int priority); extern int omap_request_dma(int dev_id, const char *dev_name, - void (* callback)(int lch, u16 ch_status, void *data), - void *data, int *dma_ch); + void (*callback)(int lch, u16 ch_status, void *data), + void *data, int *dma_ch); extern void omap_enable_dma_irq(int ch, u16 irq_bits); extern void omap_disable_dma_irq(int ch, u16 irq_bits); extern void omap_free_dma(int ch); @@ -464,17 +507,16 @@ extern void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode); extern void omap_set_dma_params(int lch, - struct omap_dma_channel_params * params); + struct omap_dma_channel_params *params); -extern void omap_dma_link_lch (int lch_head, int lch_queue); -extern void omap_dma_unlink_lch (int lch_head, int lch_queue); +extern void omap_dma_link_lch(int lch_head, int lch_queue); +extern void omap_dma_unlink_lch(int lch_head, int lch_queue); extern int omap_set_dma_callback(int lch, - void (* callback)(int lch, u16 ch_status, void *data), + void (*callback)(int lch, u16 ch_status, void *data), void *data); extern dma_addr_t omap_get_dma_src_pos(int lch); extern dma_addr_t omap_get_dma_dst_pos(int lch); -extern int omap_get_dma_src_addr_counter(int lch); extern void omap_clear_dma(int lch); extern int omap_get_dma_active_status(int lch); extern int omap_dma_running(void); @@ -482,6 +524,9 @@ extern void omap_dma_set_global_params(int arb_rate, int max_fifo_depth, int tparams); extern int omap_dma_set_prio_lch(int lch, unsigned char read_prio, unsigned char write_prio); +extern void omap_set_dma_dst_endian_type(int lch, enum end_type etype); +extern void omap_set_dma_src_endian_type(int lch, enum end_type etype); +extern int omap_get_dma_index(int lch, int *ei, int *fi); /* Chaining APIs */ #ifndef CONFIG_ARCH_OMAP1 @@ -507,7 +552,7 @@ extern int omap_dma_chain_status(int chain_id); #endif /* LCD DMA functions */ -extern int omap_request_lcd_dma(void (* callback)(u16 status, void *data), +extern int omap_request_lcd_dma(void (*callback)(u16 status, void *data), void *data); extern void omap_free_lcd_dma(void); extern void omap_setup_lcd_dma(void); -- cgit v1.2.3 From c2d43e39c7c303db53facd0bea44b66f263e3f35 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:38 +0300 Subject: ARM: OMAP: SRAM: Split sram24xx.S into sram242x.S and sram243x.S Split sram24xx.S into sram242x.S and sram243x.S Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/sram.h | 37 ++++++++++++++++++++++++++++--------- 1 file changed, 28 insertions(+), 9 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/sram.h b/include/asm-arm/arch-omap/sram.h index bb9bb3fd532..be59f4a9828 100644 --- a/include/asm-arm/arch-omap/sram.h +++ b/include/asm-arm/arch-omap/sram.h @@ -11,6 +11,7 @@ #ifndef __ARCH_ARM_OMAP_SRAM_H #define __ARCH_ARM_OMAP_SRAM_H +extern int __init omap_sram_init(void); extern void * omap_sram_push(void * start, unsigned long size); extern void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl); @@ -21,17 +22,35 @@ extern void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); /* Do not use these */ -extern void sram_reprogram_clock(u32 ckctl, u32 dpllctl); -extern unsigned long sram_reprogram_clock_sz; +extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); +extern unsigned long omap1_sram_reprogram_clock_sz; -extern void sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, - u32 base_cs, u32 force_unlock); -extern unsigned long sram_ddr_init_sz; +extern void omap24xx_sram_reprogram_clock(u32 ckctl, u32 dpllctl); +extern unsigned long omap24xx_sram_reprogram_clock_sz; -extern u32 sram_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); -extern unsigned long sram_set_prcm_sz; +extern void omap242x_sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, + u32 base_cs, u32 force_unlock); +extern unsigned long omap242x_sram_ddr_init_sz; -extern void sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type); -extern unsigned long sram_reprogram_sdrc_sz; +extern u32 omap242x_sram_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, + int bypass); +extern unsigned long omap242x_sram_set_prcm_sz; + +extern void omap242x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, + u32 mem_type); +extern unsigned long omap242x_sram_reprogram_sdrc_sz; + + +extern void omap243x_sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, + u32 base_cs, u32 force_unlock); +extern unsigned long omap243x_sram_ddr_init_sz; + +extern u32 omap243x_sram_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, + int bypass); +extern unsigned long omap243x_sram_set_prcm_sz; + +extern void omap243x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, + u32 mem_type); +extern unsigned long omap243x_sram_reprogram_sdrc_sz; #endif -- cgit v1.2.3 From bc5d0c89c88df67f92d5d5882c27437379e9e8af Mon Sep 17 00:00:00 2001 From: Eduardo Valentin Date: Thu, 3 Jul 2008 12:24:39 +0300 Subject: ARM: OMAP: McBSP: Prepare for splitting into omap1 and omap2 code This patch transform mcbsp code to use platform data from arch/arm/plat-omap/devices.c It also gets ride of ifdefs on mcbsp.c code. To do it, a platform data structure was defined. Signed-off-by: Eduardo Valentin Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/mcbsp.h | 62 +++++++++++++++++++++++++++++++++++++-- 1 file changed, 60 insertions(+), 2 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/mcbsp.h b/include/asm-arm/arch-omap/mcbsp.h index c7a0cc1c4e9..26c78f67dc8 100644 --- a/include/asm-arm/arch-omap/mcbsp.h +++ b/include/asm-arm/arch-omap/mcbsp.h @@ -24,7 +24,11 @@ #ifndef __ASM_ARCH_OMAP_MCBSP_H #define __ASM_ARCH_OMAP_MCBSP_H +#include +#include + #include +#include #define OMAP730_MCBSP1_BASE 0xfffb1000 #define OMAP730_MCBSP2_BASE 0xfffb1800 @@ -40,6 +44,9 @@ #define OMAP24XX_MCBSP1_BASE 0x48074000 #define OMAP24XX_MCBSP2_BASE 0x48076000 +#define OMAP34XX_MCBSP1_BASE 0x48074000 +#define OMAP34XX_MCBSP2_BASE 0x49022000 + #if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP730) #define OMAP_MCBSP_REG_DRR2 0x00 @@ -74,7 +81,8 @@ #define OMAP_MCBSP_REG_XCERG 0x3A #define OMAP_MCBSP_REG_XCERH 0x3C -#define OMAP_MAX_MCBSP_COUNT 3 +#define OMAP_MAX_MCBSP_COUNT 3 +#define MAX_MCBSP_CLOCKS 3 #define AUDIO_MCBSP_DATAWRITE (OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DXR1) #define AUDIO_MCBSP_DATAREAD (OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DRR1) @@ -117,7 +125,8 @@ #define OMAP_MCBSP_REG_XCERG 0x74 #define OMAP_MCBSP_REG_XCERH 0x78 -#define OMAP_MAX_MCBSP_COUNT 2 +#define OMAP_MAX_MCBSP_COUNT 2 +#define MAX_MCBSP_CLOCKS 2 #define AUDIO_MCBSP_DATAWRITE (OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DXR1) #define AUDIO_MCBSP_DATAREAD (OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DRR1) @@ -298,6 +307,55 @@ struct omap_mcbsp_spi_cfg { omap_mcbsp_word_length word_length; }; +/* Platform specific configuration */ +struct omap_mcbsp_ops { + void (*request)(unsigned int); + void (*free)(unsigned int); + int (*check)(unsigned int); +}; + +struct omap_mcbsp_platform_data { + u32 virt_base; + u8 dma_rx_sync, dma_tx_sync; + u16 rx_irq, tx_irq; + struct omap_mcbsp_ops *ops; + char const *clk_name; +}; + +struct omap_mcbsp { + struct device *dev; + u32 io_base; + u8 id; + u8 free; + omap_mcbsp_word_length rx_word_length; + omap_mcbsp_word_length tx_word_length; + + omap_mcbsp_io_type_t io_type; /* IRQ or poll */ + /* IRQ based TX/RX */ + int rx_irq; + int tx_irq; + + /* DMA stuff */ + u8 dma_rx_sync; + short dma_rx_lch; + u8 dma_tx_sync; + short dma_tx_lch; + + /* Completion queues */ + struct completion tx_irq_completion; + struct completion rx_irq_completion; + struct completion tx_dma_completion; + struct completion rx_dma_completion; + + /* Protect the field .free, while checking if the mcbsp is in use */ + spinlock_t lock; + struct omap_mcbsp_platform_data *pdata; + struct clk *clk; +}; + +int omap_mcbsp_init(void); +void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config, + int size); void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg * config); int omap_mcbsp_request(unsigned int id); void omap_mcbsp_free(unsigned int id); -- cgit v1.2.3 From 44f78f43b349d19d378a996c4a2d9fcdff771b1e Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:41 +0300 Subject: ARM: OMAP: Clean up interrupt lines to fix warnings for multi-omap If boards with different NR_IRQS are compiled together, tons of compiler warnings are emitted about redefining NR_IRQS. This patch fixes the problem by adding up NR_IRQS in a common place. Patch also removes quite a bit of now unnecessary code. Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/board-2430sdp.h | 5 --- include/asm-arm/arch-omap/board-h3.h | 6 ---- include/asm-arm/arch-omap/board-innovator.h | 3 -- include/asm-arm/arch-omap/board-perseus2.h | 6 ---- include/asm-arm/arch-omap/fpga.h | 49 ++++++++++++++--------------- include/asm-arm/arch-omap/irqs.h | 44 ++++++++++++++++++++------ 6 files changed, 59 insertions(+), 54 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/board-2430sdp.h b/include/asm-arm/arch-omap/board-2430sdp.h index e9c65ce3cb1..c7db9004ec3 100644 --- a/include/asm-arm/arch-omap/board-2430sdp.h +++ b/include/asm-arm/arch-omap/board-2430sdp.h @@ -36,9 +36,4 @@ #define TWL4030_IRQNUM INT_24XX_SYS_NIRQ -/* TWL4030 Primary Interrupt Handler (PIH) interrupts */ -#define IH_TWL4030_BASE IH_BOARD_BASE -#define IH_TWL4030_END (IH_TWL4030_BASE+8) -#define NR_IRQS (IH_TWL4030_END) - #endif /* __ASM_ARCH_OMAP_2430SDP_H */ diff --git a/include/asm-arm/arch-omap/board-h3.h b/include/asm-arm/arch-omap/board-h3.h index 0f6404435ea..c5d0f32a40a 100644 --- a/include/asm-arm/arch-omap/board-h3.h +++ b/include/asm-arm/arch-omap/board-h3.h @@ -30,12 +30,6 @@ /* In OMAP1710 H3 the Ethernet is directly connected to CS1 */ #define OMAP1710_ETHR_START 0x04000300 -#define MAXIRQNUM (IH_BOARD_BASE) -#define MAXFIQNUM MAXIRQNUM -#define MAXSWINUM MAXIRQNUM - -#define NR_IRQS (MAXIRQNUM + 1) - extern void h3_mmc_init(void); extern void h3_mmc_slot_cover_handler(void *arg, int state); diff --git a/include/asm-arm/arch-omap/board-innovator.h b/include/asm-arm/arch-omap/board-innovator.h index 56d2c98e143..9ca03dec9d3 100644 --- a/include/asm-arm/arch-omap/board-innovator.h +++ b/include/asm-arm/arch-omap/board-innovator.h @@ -36,9 +36,6 @@ #define OMAP1510P1_EMIFS_PRI_VALUE 0x00 #define OMAP1510P1_EMIFF_PRI_VALUE 0x00 -#define NR_FPGA_IRQS 24 -#define NR_IRQS (IH_BOARD_BASE + NR_FPGA_IRQS) - #ifndef __ASSEMBLY__ void fpga_write(unsigned char val, int reg); unsigned char fpga_read(int reg); diff --git a/include/asm-arm/arch-omap/board-perseus2.h b/include/asm-arm/arch-omap/board-perseus2.h index eb74420cb43..d7429cb0f72 100644 --- a/include/asm-arm/arch-omap/board-perseus2.h +++ b/include/asm-arm/arch-omap/board-perseus2.h @@ -36,10 +36,4 @@ #define OMAP_SDRAM_DEVICE D256M_1X16_4B #endif -#define MAXIRQNUM IH_BOARD_BASE -#define MAXFIQNUM MAXIRQNUM -#define MAXSWINUM MAXIRQNUM - -#define NR_IRQS (MAXIRQNUM + 1) - #endif diff --git a/include/asm-arm/arch-omap/fpga.h b/include/asm-arm/arch-omap/fpga.h index 6a883e0bdbb..f420881d2a3 100644 --- a/include/asm-arm/arch-omap/fpga.h +++ b/include/asm-arm/arch-omap/fpga.h @@ -169,30 +169,29 @@ struct h2p2_dbg_fpga { #define OMAP1510_INT_FPGA (IH_GPIO_BASE + 13) /* IRQ Numbers for interrupts muxed through the FPGA */ -#define OMAP1510_IH_FPGA_BASE IH_BOARD_BASE -#define OMAP1510_INT_FPGA_ATN (OMAP1510_IH_FPGA_BASE + 0) -#define OMAP1510_INT_FPGA_ACK (OMAP1510_IH_FPGA_BASE + 1) -#define OMAP1510_INT_FPGA2 (OMAP1510_IH_FPGA_BASE + 2) -#define OMAP1510_INT_FPGA3 (OMAP1510_IH_FPGA_BASE + 3) -#define OMAP1510_INT_FPGA4 (OMAP1510_IH_FPGA_BASE + 4) -#define OMAP1510_INT_FPGA5 (OMAP1510_IH_FPGA_BASE + 5) -#define OMAP1510_INT_FPGA6 (OMAP1510_IH_FPGA_BASE + 6) -#define OMAP1510_INT_FPGA7 (OMAP1510_IH_FPGA_BASE + 7) -#define OMAP1510_INT_FPGA8 (OMAP1510_IH_FPGA_BASE + 8) -#define OMAP1510_INT_FPGA9 (OMAP1510_IH_FPGA_BASE + 9) -#define OMAP1510_INT_FPGA10 (OMAP1510_IH_FPGA_BASE + 10) -#define OMAP1510_INT_FPGA11 (OMAP1510_IH_FPGA_BASE + 11) -#define OMAP1510_INT_FPGA12 (OMAP1510_IH_FPGA_BASE + 12) -#define OMAP1510_INT_ETHER (OMAP1510_IH_FPGA_BASE + 13) -#define OMAP1510_INT_FPGAUART1 (OMAP1510_IH_FPGA_BASE + 14) -#define OMAP1510_INT_FPGAUART2 (OMAP1510_IH_FPGA_BASE + 15) -#define OMAP1510_INT_FPGA_TS (OMAP1510_IH_FPGA_BASE + 16) -#define OMAP1510_INT_FPGA17 (OMAP1510_IH_FPGA_BASE + 17) -#define OMAP1510_INT_FPGA_CAM (OMAP1510_IH_FPGA_BASE + 18) -#define OMAP1510_INT_FPGA_RTC_A (OMAP1510_IH_FPGA_BASE + 19) -#define OMAP1510_INT_FPGA_RTC_B (OMAP1510_IH_FPGA_BASE + 20) -#define OMAP1510_INT_FPGA_CD (OMAP1510_IH_FPGA_BASE + 21) -#define OMAP1510_INT_FPGA22 (OMAP1510_IH_FPGA_BASE + 22) -#define OMAP1510_INT_FPGA23 (OMAP1510_IH_FPGA_BASE + 23) +#define OMAP1510_INT_FPGA_ATN (OMAP_FPGA_IRQ_BASE + 0) +#define OMAP1510_INT_FPGA_ACK (OMAP_FPGA_IRQ_BASE + 1) +#define OMAP1510_INT_FPGA2 (OMAP_FPGA_IRQ_BASE + 2) +#define OMAP1510_INT_FPGA3 (OMAP_FPGA_IRQ_BASE + 3) +#define OMAP1510_INT_FPGA4 (OMAP_FPGA_IRQ_BASE + 4) +#define OMAP1510_INT_FPGA5 (OMAP_FPGA_IRQ_BASE + 5) +#define OMAP1510_INT_FPGA6 (OMAP_FPGA_IRQ_BASE + 6) +#define OMAP1510_INT_FPGA7 (OMAP_FPGA_IRQ_BASE + 7) +#define OMAP1510_INT_FPGA8 (OMAP_FPGA_IRQ_BASE + 8) +#define OMAP1510_INT_FPGA9 (OMAP_FPGA_IRQ_BASE + 9) +#define OMAP1510_INT_FPGA10 (OMAP_FPGA_IRQ_BASE + 10) +#define OMAP1510_INT_FPGA11 (OMAP_FPGA_IRQ_BASE + 11) +#define OMAP1510_INT_FPGA12 (OMAP_FPGA_IRQ_BASE + 12) +#define OMAP1510_INT_ETHER (OMAP_FPGA_IRQ_BASE + 13) +#define OMAP1510_INT_FPGAUART1 (OMAP_FPGA_IRQ_BASE + 14) +#define OMAP1510_INT_FPGAUART2 (OMAP_FPGA_IRQ_BASE + 15) +#define OMAP1510_INT_FPGA_TS (OMAP_FPGA_IRQ_BASE + 16) +#define OMAP1510_INT_FPGA17 (OMAP_FPGA_IRQ_BASE + 17) +#define OMAP1510_INT_FPGA_CAM (OMAP_FPGA_IRQ_BASE + 18) +#define OMAP1510_INT_FPGA_RTC_A (OMAP_FPGA_IRQ_BASE + 19) +#define OMAP1510_INT_FPGA_RTC_B (OMAP_FPGA_IRQ_BASE + 20) +#define OMAP1510_INT_FPGA_CD (OMAP_FPGA_IRQ_BASE + 21) +#define OMAP1510_INT_FPGA22 (OMAP_FPGA_IRQ_BASE + 22) +#define OMAP1510_INT_FPGA23 (OMAP_FPGA_IRQ_BASE + 23) #endif diff --git a/include/asm-arm/arch-omap/irqs.h b/include/asm-arm/arch-omap/irqs.h index 87973654e62..7464c694859 100644 --- a/include/asm-arm/arch-omap/irqs.h +++ b/include/asm-arm/arch-omap/irqs.h @@ -285,7 +285,41 @@ #define OMAP_MAX_GPIO_LINES 192 #define IH_GPIO_BASE (128 + IH2_BASE) #define IH_MPUIO_BASE (OMAP_MAX_GPIO_LINES + IH_GPIO_BASE) -#define IH_BOARD_BASE (16 + IH_MPUIO_BASE) +#define OMAP_IRQ_END (IH_MPUIO_BASE + 16) + +/* External FPGA handles interrupts on Innovator boards */ +#define OMAP_FPGA_IRQ_BASE (OMAP_IRQ_END) +#ifdef CONFIG_MACH_OMAP_INNOVATOR +#define OMAP_FPGA_NR_IRQS 24 +#else +#define OMAP_FPGA_NR_IRQS 0 +#endif +#define OMAP_FPGA_IRQ_END (OMAP_FPGA_IRQ_BASE + OMAP_FPGA_NR_IRQS) + +/* External TWL4030 can handle interrupts on 2430 and 34xx boards */ +#define TWL4030_IRQ_BASE (OMAP_FPGA_IRQ_END) +#ifdef CONFIG_TWL4030_CORE +#define TWL4030_BASE_NR_IRQS 8 +#define TWL4030_PWR_NR_IRQS 8 +#else +#define TWL4030_BASE_NR_IRQS 0 +#define TWL4030_PWR_NR_IRQS 0 +#endif +#define TWL4030_IRQ_END (TWL4030_IRQ_BASE + TWL4030_BASE_NR_IRQS) +#define TWL4030_PWR_IRQ_BASE TWL4030_IRQ_END +#define TWL4030_PWR_IRQ_END (TWL4030_PWR_IRQ_BASE + TWL4030_PWR_NR_IRQS) + +/* External TWL4030 gpio interrupts are optional */ +#define TWL4030_GPIO_IRQ_BASE TWL4030_PWR_IRQ_END +#ifdef CONFIG_TWL4030_GPIO +#define TWL4030_GPIO_NR_IRQS 18 +#else +#define TWL4030_GPIO_NR_IRQS 0 +#endif +#define TWL4030_GPIO_IRQ_END (TWL4030_GPIO_IRQ_BASE + TWL4030_GPIO_NR_IRQS) + +/* Total number of interrupts depends on the enabled blocks above */ +#define NR_IRQS TWL4030_GPIO_IRQ_END #define OMAP_IRQ_BIT(irq) (1 << ((irq) % 32)) @@ -293,14 +327,6 @@ extern void omap_init_irq(void); #endif -/* - * The definition of NR_IRQS is in board-specific header file, which is - * included via hardware.h - */ #include -#ifndef NR_IRQS -#define NR_IRQS IH_BOARD_BASE -#endif - #endif -- cgit v1.2.3 From 137b3ee27ab1b27dba081542476054836978ca45 Mon Sep 17 00:00:00 2001 From: Hiroshi DOYU Date: Thu, 3 Jul 2008 12:24:41 +0300 Subject: ARM: OMAP: CLKFW: Initial debugfs support for omap clock framework debugfs can provide the infrastructure to trace the dependencies of clock tree hierarchy quite visibly. This patch enables to keep track of clock tree hierarchy and expose their attributes under each clock directry as below: omap:~# tree -d -L 2 /debug/clock/omap_32k_fck/ /debug/clock/omap_32k_fck/ |-- gpt10_fck |-- gpt11_fck |-- gpt1_fck |-- per_32k_alwon_fck | |-- gpio2_fck | |-- gpio3_fck | |-- gpio4_fck | |-- gpio5_fck | |-- gpio6_fck | `-- wdt3_fck |-- ts_fck `-- wkup_32k_fck |-- gpio1_fck `-- wdt2_fck 14 directories omap:~# tree /debug/clock/omap_32k_fck/gpt10_fck/ /debug/clock/omap_32k_fck/gpt10_fck/ |-- flags |-- rate `-- usecount 0 directories, 3 files Although, compared with David Brownell's small patch, this may look bit overkilling, I expect that this debugfs can deal with other PRCM complexities at the same time. For example, powerdomain dependencies can be expressed by using symbolic links of these clocks if powerdomain supports dubgfs as well. Signed-off-by: Hiroshi DOYU Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/clock.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/clock.h b/include/asm-arm/arch-omap/clock.h index 12a5e4de951..8490fbba39d 100644 --- a/include/asm-arm/arch-omap/clock.h +++ b/include/asm-arm/arch-omap/clock.h @@ -71,6 +71,9 @@ struct clk { __u8 rate_offset; __u8 src_offset; #endif +#if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS) + struct dentry *dent; /* For visible tree hierarchy */ +#endif }; struct cpufreq_frequency_table; -- cgit v1.2.3 From 030b15457d8069a6255579a28db196e002cb9c86 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:41 +0300 Subject: ARM: OMAP: Change omap_cf.c and omap_nor.c to use omap_readw/writew instead of __REG Change omap_cf.c and omap_nor.c to use omap_readw/writew instead of __REG. This is needed for multi-omap in the future. Cc: David Brownell Cc: linux-pcmcia@lists.infradead.org Cc: linux-mtd@lists.infradead.org Signed-off-by: Tony Lindren --- include/asm-arm/arch-omap/tc.h | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/tc.h b/include/asm-arm/arch-omap/tc.h index 8ded218cbea..65a9c82d3bf 100644 --- a/include/asm-arm/arch-omap/tc.h +++ b/include/asm-arm/arch-omap/tc.h @@ -75,16 +75,14 @@ #ifndef __ASSEMBLER__ /* EMIF Slow Interface Configuration Register */ -#define OMAP_EMIFS_CONFIG_REG __REG32(EMIFS_CONFIG) - #define OMAP_EMIFS_CONFIG_FR (1 << 4) #define OMAP_EMIFS_CONFIG_PDE (1 << 3) #define OMAP_EMIFS_CONFIG_PWD_EN (1 << 2) #define OMAP_EMIFS_CONFIG_BM (1 << 1) #define OMAP_EMIFS_CONFIG_WP (1 << 0) -#define EMIFS_CCS(n) __REG32(EMIFS_CS0_CONFIG + (4 * (n))) -#define EMIFS_ACS(n) __REG32(EMIFS_ACS0 + (4 * (n))) +#define EMIFS_CCS(n) (EMIFS_CS0_CONFIG + (4 * (n))) +#define EMIFS_ACS(n) (EMIFS_ACS0 + (4 * (n))) /* Almost all documentation for chip and board memory maps assumes * BM is clear. Most devel boards have a switch to control booting @@ -93,13 +91,13 @@ */ static inline u32 omap_cs0_phys(void) { - return (OMAP_EMIFS_CONFIG_REG & OMAP_EMIFS_CONFIG_BM) + return (omap_readl(EMIFS_CONFIG) & OMAP_EMIFS_CONFIG_BM) ? OMAP_CS3_PHYS : 0; } static inline u32 omap_cs3_phys(void) { - return (OMAP_EMIFS_CONFIG_REG & OMAP_EMIFS_CONFIG_BM) + return (omap_readl(EMIFS_CONFIG) & OMAP_EMIFS_CONFIG_BM) ? 0 : OMAP_CS3_PHYS; } -- cgit v1.2.3 From f35ae6346850f6c192269b09088b20261760f0e0 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:43 +0300 Subject: ARM: OMAP: USB: Change omap USB code to use omap_read/write instead of __REG Change omap USB code to use omap_read/write instead of __REG for multi-omap Cc: David Brownell Cc: linux-usb@vger.kernel.org Cc: i2c@lm-sensors.org Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/usb.h | 23 ++++++++++------------- 1 file changed, 10 insertions(+), 13 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/usb.h b/include/asm-arm/arch-omap/usb.h index 2147d18aaea..ddf1861e6df 100644 --- a/include/asm-arm/arch-omap/usb.h +++ b/include/asm-arm/arch-omap/usb.h @@ -34,11 +34,8 @@ /* * OTG and transceiver registers, for OMAPs starting with ARM926 */ -#define OTG_REG32(offset) __REG32(OTG_BASE + (offset)) -#define OTG_REG16(offset) __REG16(OTG_BASE + (offset)) - -#define OTG_REV_REG OTG_REG32(0x00) -#define OTG_SYSCON_1_REG OTG_REG32(0x04) +#define OTG_REV (OTG_BASE + 0x00) +#define OTG_SYSCON_1 (OTG_BASE + 0x04) # define USB2_TRX_MODE(w) (((w)>>24)&0x07) # define USB1_TRX_MODE(w) (((w)>>20)&0x07) # define USB0_TRX_MODE(w) (((w)>>16)&0x07) @@ -47,7 +44,7 @@ # define DEV_IDLE_EN (1 << 13) # define OTG_RESET_DONE (1 << 2) # define OTG_SOFT_RESET (1 << 1) -#define OTG_SYSCON_2_REG OTG_REG32(0x08) +#define OTG_SYSCON_2 (OTG_BASE + 0x08) # define OTG_EN (1 << 31) # define USBX_SYNCHRO (1 << 30) # define OTG_MST16 (1 << 29) @@ -65,7 +62,7 @@ # define HMC_TLLSPEED (1 << 7) # define HMC_TLLATTACH (1 << 6) # define OTG_HMC(w) (((w)>>0)&0x3f) -#define OTG_CTRL_REG OTG_REG32(0x0c) +#define OTG_CTRL (OTG_BASE + 0x0c) # define OTG_USB2_EN (1 << 29) # define OTG_USB2_DP (1 << 28) # define OTG_USB2_DM (1 << 27) @@ -92,7 +89,7 @@ # define OTG_PD_VBUS (1 << 2) # define OTG_PU_VBUS (1 << 1) # define OTG_PU_ID (1 << 0) -#define OTG_IRQ_EN_REG OTG_REG16(0x10) +#define OTG_IRQ_EN (OTG_BASE + 0x10) /* 16-bit */ # define DRIVER_SWITCH (1 << 15) # define A_VBUS_ERR (1 << 13) # define A_REQ_TMROUT (1 << 12) @@ -102,9 +99,9 @@ # define B_SRP_DONE (1 << 8) # define B_SRP_STARTED (1 << 7) # define OPRT_CHG (1 << 0) -#define OTG_IRQ_SRC_REG OTG_REG16(0x14) +#define OTG_IRQ_SRC (OTG_BASE + 0x14) /* 16-bit */ // same bits as in IRQ_EN -#define OTG_OUTCTRL_REG OTG_REG16(0x18) +#define OTG_OUTCTRL (OTG_BASE + 0x18) /* 16-bit */ # define OTGVPD (1 << 14) # define OTGVPU (1 << 13) # define OTGPUID (1 << 12) @@ -117,13 +114,13 @@ # define USB0VDR (1 << 2) # define USB0PDEN (1 << 1) # define USB0PUEN (1 << 0) -#define OTG_TEST_REG OTG_REG16(0x20) -#define OTG_VENDOR_CODE_REG OTG_REG32(0xfc) +#define OTG_TEST (OTG_BASE + 0x20) /* 16-bit */ +#define OTG_VENDOR_CODE (OTG_BASE + 0xfc) /* 16-bit */ /*-------------------------------------------------------------------------*/ /* OMAP1 */ -#define USB_TRANSCEIVER_CTRL_REG __REG32(0xfffe1000 + 0x0064) +#define USB_TRANSCEIVER_CTRL (0xfffe1000 + 0x0064) # define CONF_USB2_UNI_R (1 << 8) # define CONF_USB1_UNI_R (1 << 7) # define CONF_USB_PORT0_R(x) (((x)>>4)&0x7) -- cgit v1.2.3 From e1f80bfca86ab48b7bed731b32262fb1a2835de5 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:43 +0300 Subject: ARM: OMAP: Remove __REG access for multi-omap This does not play nicely with multi-omap as it cannot be replaced by a function in io.c for omaps with different IO bases. Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/io.h | 23 ----------------------- 1 file changed, 23 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/io.h b/include/asm-arm/arch-omap/io.h index 160578e1f55..e1fb7ec7d47 100644 --- a/include/asm-arm/arch-omap/io.h +++ b/include/asm-arm/arch-omap/io.h @@ -183,35 +183,12 @@ #define omap_writew(v,a) (*(volatile unsigned short *)IO_ADDRESS(a) = (v)) #define omap_writel(v,a) (*(volatile unsigned int *)IO_ADDRESS(a) = (v)) -/* 16 bit uses LDRH/STRH, base +/- offset_8 */ -typedef struct { volatile u16 offset[256]; } __regbase16; -#define __REGV16(vaddr) ((__regbase16 *)((vaddr)&~0xff)) \ - ->offset[((vaddr)&0xff)>>1] -#define __REG16(paddr) __REGV16(io_p2v(paddr)) - -/* 8/32 bit uses LDR/STR, base +/- offset_12 */ -typedef struct { volatile u8 offset[4096]; } __regbase8; -#define __REGV8(vaddr) ((__regbase8 *)((vaddr)&~4095)) \ - ->offset[((vaddr)&4095)>>0] -#define __REG8(paddr) __REGV8(io_p2v(paddr)) - -typedef struct { volatile u32 offset[4096]; } __regbase32; -#define __REGV32(vaddr) ((__regbase32 *)((vaddr)&~4095)) \ - ->offset[((vaddr)&4095)>>2] -#define __REG32(paddr) __REGV32(io_p2v(paddr)) - extern void omap1_map_common_io(void); extern void omap1_init_common_hw(void); extern void omap2_map_common_io(void); extern void omap2_init_common_hw(void); -#else - -#define __REG8(paddr) io_p2v(paddr) -#define __REG16(paddr) io_p2v(paddr) -#define __REG32(paddr) io_p2v(paddr) - #endif #endif -- cgit v1.2.3 From a58caad11301a5bdc2d7b76596ab5477221f7a9b Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:44 +0300 Subject: ARM: OMAP: Introduce omap_globals and prcm access functions for multi-omap New struct omap_globals contains the omap processor specific module bases. Use omap_globals to set the various base addresses to make detecting omap chip type simpler. Also introduce OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS for future multi-omap patches. Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/common.h | 15 +++++++++++++++ include/asm-arm/arch-omap/control.h | 4 +--- include/asm-arm/arch-omap/io.h | 3 +++ 3 files changed, 19 insertions(+), 3 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/common.h b/include/asm-arm/arch-omap/common.h index 36a3b62d4d8..8ac03071f60 100644 --- a/include/asm-arm/arch-omap/common.h +++ b/include/asm-arm/arch-omap/common.h @@ -47,8 +47,23 @@ static inline int omap_register_i2c_bus(int bus_id, u32 clkrate, } #endif +/* IO bases for various OMAP processors */ +struct omap_globals { + void __iomem *tap; /* Control module ID code */ + void __iomem *sdrc; /* SDRAM Controller */ + void __iomem *sms; /* SDRAM Memory Scheduler */ + void __iomem *ctrl; /* System Control Module */ + void __iomem *prm; /* Power and Reset Management */ + void __iomem *cm; /* Clock Management */ +}; + void omap2_set_globals_242x(void); void omap2_set_globals_243x(void); void omap2_set_globals_343x(void); +/* These get called from omap2_set_globals_xxxx(), do not call these */ +void omap2_set_globals_memory(struct omap_globals *); +void omap2_set_globals_control(struct omap_globals *); +void omap2_set_globals_prcm(struct omap_globals *); + #endif /* __ARCH_ARM_MACH_OMAP_COMMON_H */ diff --git a/include/asm-arm/arch-omap/control.h b/include/asm-arm/arch-omap/control.h index 59c0686f8be..987553e3eeb 100644 --- a/include/asm-arm/arch-omap/control.h +++ b/include/asm-arm/arch-omap/control.h @@ -167,8 +167,7 @@ #ifndef __ASSEMBLY__ #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) -extern void omap_ctrl_base_set(u32 base); -extern u32 omap_ctrl_base_get(void); +extern void __iomem *omap_ctrl_base_get(void); extern u8 omap_ctrl_readb(u16 offset); extern u16 omap_ctrl_readw(u16 offset); extern u32 omap_ctrl_readl(u16 offset); @@ -176,7 +175,6 @@ extern void omap_ctrl_writeb(u8 val, u16 offset); extern void omap_ctrl_writew(u16 val, u16 offset); extern void omap_ctrl_writel(u32 val, u16 offset); #else -#define omap_ctrl_base_set(x) WARN_ON(1) #define omap_ctrl_base_get() 0 #define omap_ctrl_readb(x) 0 #define omap_ctrl_readw(x) 0 diff --git a/include/asm-arm/arch-omap/io.h b/include/asm-arm/arch-omap/io.h index e1fb7ec7d47..0b13557fd30 100644 --- a/include/asm-arm/arch-omap/io.h +++ b/include/asm-arm/arch-omap/io.h @@ -60,6 +60,7 @@ #define IO_SIZE 0x40000 #define IO_VIRT (IO_PHYS - IO_OFFSET) #define IO_ADDRESS(pa) ((pa) - IO_OFFSET) +#define OMAP1_IO_ADDRESS(pa) ((pa) - IO_OFFSET) #define io_p2v(pa) ((pa) - IO_OFFSET) #define io_v2p(va) ((va) + IO_OFFSET) @@ -91,6 +92,7 @@ #define IO_OFFSET 0x90000000 #define IO_ADDRESS(pa) ((pa) + IO_OFFSET) /* Works for L3 and L4 */ +#define OMAP2_IO_ADDRESS(pa) ((pa) + IO_OFFSET) /* Works for L3 and L4 */ #define io_p2v(pa) ((pa) + IO_OFFSET) /* Works for L3 and L4 */ #define io_v2p(va) ((va) - IO_OFFSET) /* Works for L3 and L4 */ @@ -148,6 +150,7 @@ #define IO_OFFSET 0x90000000 #define IO_ADDRESS(pa) ((pa) + IO_OFFSET)/* Works for L3 and L4 */ +#define OMAP2_IO_ADDRESS(pa) ((pa) + IO_OFFSET)/* Works for L3 and L4 */ #define io_p2v(pa) ((pa) + IO_OFFSET)/* Works for L3 and L4 */ #define io_v2p(va) ((va) - IO_OFFSET)/* Works for L3 and L4 */ -- cgit v1.2.3 From 097c584cd48844d9ef8402bdc6ab49e7e2135f31 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Thu, 3 Jul 2008 12:24:45 +0300 Subject: ARM: OMAP: Add OMAP chip type structure; clean up mach-omap2/id.c Add a new OMAP chip identification interface, omap_chip_id. omap_chip_id is a structure which contains one bit for each OMAP2/3 CPU type, and on 3430, ES level. For example, the CHIP_IS_OMAP2420 bit is set in omap_chip at boot on an OMAP2420. On OMAP3430ES2, both CHIP_IS_OMAP3430 and CHIP_IS_OMAP3430ES2 bits are set. omap_chip is set in mach-omap2/id.c by _set_omap_chip(). Other code should use the omap_chip_is() function to test against omap_chip. Also, clean up id.c by splitting some code out of omap_check_revision() into its own function, _set_system_rev(); and converting some debug printk()s into pr_debug(). Second revision. Signed-off-by: Paul Walmsley Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/cpu.h | 39 +++++++++++++++++++++++++++++++++++++-- 1 file changed, 37 insertions(+), 2 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/cpu.h b/include/asm-arm/arch-omap/cpu.h index e8a4cf52778..52db09f8328 100644 --- a/include/asm-arm/arch-omap/cpu.h +++ b/include/asm-arm/arch-omap/cpu.h @@ -3,7 +3,7 @@ * * OMAP cpu type detection * - * Copyright (C) 2004 Nokia Corporation + * Copyright (C) 2004, 2008 Nokia Corporation * * Written by Tony Lindgren * @@ -26,6 +26,12 @@ #ifndef __ASM_ARCH_OMAP_CPU_H #define __ASM_ARCH_OMAP_CPU_H +struct omap_chip_id { + u8 oc; +}; + +#define OMAP_CHIP_INIT(x) { .oc = x } + extern unsigned int system_rev; #define omap2_cpu_rev() ((system_rev >> 12) & 0x0f) @@ -345,6 +351,33 @@ IS_OMAP_TYPE(3430, 0x3430) #define OMAP2430_REV_ES1_0 0x24300000 #define OMAP3430_REV_ES1_0 0x34300000 #define OMAP3430_REV_ES2_0 0x34301000 +#define OMAP3430_REV_ES2_1 0x34302000 +#define OMAP3430_REV_ES2_2 0x34303000 + +/* + * omap_chip bits + * + * CHIP_IS_OMAP{2420,2430,3430} indicate that a particular structure is + * valid on all chips of that type. CHIP_IS_OMAP3430ES{1,2} indicates + * something that is only valid on that particular ES revision. + * + * These bits may be ORed together to indicate structures that are + * available on multiple chip types. + * + * To test whether a particular structure matches the current OMAP chip type, + * use omap_chip_is(). + * + */ +#define CHIP_IS_OMAP2420 (1 << 0) +#define CHIP_IS_OMAP2430 (1 << 1) +#define CHIP_IS_OMAP3430 (1 << 2) +#define CHIP_IS_OMAP3430ES1 (1 << 3) +#define CHIP_IS_OMAP3430ES2 (1 << 4) + +#define CHIP_IS_OMAP24XX (CHIP_IS_OMAP2420 | CHIP_IS_OMAP2430) + +int omap_chip_is(struct omap_chip_id oci); + /* * Macro to detect device type i.e. EMU/HS/TST/GP/BAD @@ -362,6 +395,8 @@ IS_OMAP_TYPE(3430, 0x3430) #define is_device_type_gp() (get_device_type() == DEVICE_TYPE_GP) #define is_device_type_bad() (get_device_type() == DEVICE_TYPE_BAD) -#endif +void omap2_check_revision(void); + +#endif /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */ #endif -- cgit v1.2.3 From 542313cc98e72d026d2df86f515699dfaface460 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Thu, 3 Jul 2008 12:24:45 +0300 Subject: ARM: OMAP2: Clock: Add OMAP3 DPLL autoidle functions This patch adds support for DPLL autoidle control to the OMAP3 clock framework. These functions will be used by the noncore DPLL enable and disable code - this is because, according to the CDP code, the DPLL autoidle status must be saved and restored across DPLL lock/bypass/off transitions. N.B.: the CORE DPLL (DPLL3) has three autoidle mode options, rather than just two. This code currently does not support the third option, low-power bypass autoidle. Signed-off-by: Paul Walmsley Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/clock.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/clock.h b/include/asm-arm/arch-omap/clock.h index 8490fbba39d..22daa5d64d3 100644 --- a/include/asm-arm/arch-omap/clock.h +++ b/include/asm-arm/arch-omap/clock.h @@ -34,11 +34,16 @@ struct dpll_data { u32 mult_mask; u32 div1_mask; # if defined(CONFIG_ARCH_OMAP3) + u8 modes; void __iomem *control_reg; u32 enable_mask; u8 auto_recal_bit; u8 recal_en_bit; u8 recal_st_bit; + void __iomem *autoidle_reg; + u32 autoidle_mask; + void __iomem *idlest_reg; + u8 idlest_bit; # endif }; -- cgit v1.2.3 From 88b8ba90570067178d32c654ad95786041e86e86 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Thu, 3 Jul 2008 12:24:46 +0300 Subject: ARM: OMAP2: Clock: New OMAP2/3 DPLL rate rounding algorithm This patch adds a new rate rounding algorithm for DPLL clocks on the OMAP2/3 architecture. For a desired DPLL target rate, there may be several multiplier/divider (M, N) values which will generate a sufficiently close rate. Lower N values result in greater power economy. However, lower N values can cause the difference between the rounded rate and the target rate ("rate error") to be larger than it would be with a higher N. This can cause downstream devices to run more slowly than they otherwise would. This DPLL rate rounding algorithm: - attempts to find the lowest possible N (DPLL divider) to reach the target_rate (since, according to Richard Woodruff , lower N values save more power than higher N values). - allows developers to set an upper bound on the error between the rounded rate and the desired target rate ("rate tolerance"), so an appropriate balance between rate fidelity and power savings can be set. This maximum rate error tolerance is set via omap2_set_dpll_rate_tolerance(). - never returns a rounded rate higher than the target rate. The rate rounding algorithm caches the last rounded M, N, and rate computation to avoid rounding the rate twice for each clk_set_rate() call. (This patch does not yet implement set_rate for DPLLs; that follows in a future patch.) The algorithm trades execution speed for rate accuracy. It will find the (M, N) set that results in the least rate error, within a specified rate tolerance. It does this by evaluating each divider setting - on OMAP3, this involves 128 steps. Another approach to DPLL rate rounding would be to bail out as soon as a valid rate is found within the rate tolerance, which would trade rate accuracy for execution speed. Alternate implementations welcome. This code is not yet used by the OMAP24XX DPLL clock, since it is currently defined as a composite clock, fusing the DPLL M,N and the M2 output divider. This patch also renames the existing OMAP24xx DPLL programming functions to highlight that they program both the DPLL and the DPLL's output multiplier. Signed-off-by: Paul Walmsley Signed-off-by: Tony Lindgren --- include/asm-arm/arch-omap/clock.h | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-omap/clock.h b/include/asm-arm/arch-omap/clock.h index 22daa5d64d3..4c7b3514f71 100644 --- a/include/asm-arm/arch-omap/clock.h +++ b/include/asm-arm/arch-omap/clock.h @@ -33,6 +33,13 @@ struct dpll_data { void __iomem *mult_div1_reg; u32 mult_mask; u32 div1_mask; + u16 last_rounded_m; + u8 last_rounded_n; + unsigned long last_rounded_rate; + unsigned int rate_tolerance; + u16 max_multiplier; + u8 max_divider; + u32 max_tolerance; # if defined(CONFIG_ARCH_OMAP3) u8 modes; void __iomem *control_reg; @@ -71,7 +78,7 @@ struct clk { void __iomem *clksel_reg; u32 clksel_mask; const struct clksel *clksel; - const struct dpll_data *dpll_data; + struct dpll_data *dpll_data; #else __u8 rate_offset; __u8 src_offset; -- cgit v1.2.3 From 5cca91479b8ac6a60b61bc56e72389c681387211 Mon Sep 17 00:00:00 2001 From: eric miao Date: Sun, 13 Apr 2008 21:46:34 +0100 Subject: [ARM] pxa: make zylonite use the generic PWM backlight driver Patch mostly by Eric Miao, minor edits by rmk. Signed-off-by: eric miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/zylonite.h | 1 - 1 file changed, 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/zylonite.h b/include/asm-arm/arch-pxa/zylonite.h index 4881b80f0f9..de577de8d18 100644 --- a/include/asm-arm/arch-pxa/zylonite.h +++ b/include/asm-arm/arch-pxa/zylonite.h @@ -15,7 +15,6 @@ struct platform_mmc_slot { extern struct platform_mmc_slot zylonite_mmc_slot[]; -extern int gpio_backlight; extern int gpio_eth_irq; extern int wm9713_irq; -- cgit v1.2.3 From 50bbb05d60e1897abad92d42bf185314be36bd74 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 19 Apr 2008 15:56:08 +0100 Subject: [ARM] rpc: deprecate __ioaddr() and __ioaddrc() helpers Now everything is converted to use MMIO accessors, these helpers are no longer required. Signed-off-by: Russell King --- include/asm-arm/arch-rpc/io.h | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-rpc/io.h b/include/asm-arm/arch-rpc/io.h index b4da08d7a33..6bd2295c0e0 100644 --- a/include/asm-arm/arch-rpc/io.h +++ b/include/asm-arm/arch-rpc/io.h @@ -126,7 +126,7 @@ static inline unsigned sz __in##fnsuffix (unsigned int port) \ return (unsigned sz)value; \ } -static inline void __iomem *__ioaddr(unsigned int port) +static inline void __iomem *__deprecated __ioaddr(unsigned int port) { void __iomem *ret; if (__PORT_PCIO(port)) @@ -232,8 +232,7 @@ DECLARE_IO(int,l,"") result; \ }) -#define __ioaddrc(port) \ - ((__PORT_PCIO(port) ? PCIO_BASE : IO_BASE) + ((port) << 2)) +#define __ioaddrc(port) __ioaddr(port) #define inb(p) (__builtin_constant_p((p)) ? __inbc(p) : __inb(p)) #define inw(p) (__builtin_constant_p((p)) ? __inwc(p) : __inw(p)) -- cgit v1.2.3 From 9ecba1f288d2cf87d1b6a9401d5ce17464eb776d Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 19 Apr 2008 16:01:38 +0100 Subject: [ARM] rpc: ecard: remove deprecated ecard_address() and relatives ecard_address() is obsolete, and has been marked deprecated since at least 2.6.12-rc2. All in-tree users have been updated to use the new approach, so it's time to remove this. Signed-off-by: Russell King --- include/asm-arm/ecard.h | 35 ----------------------------------- 1 file changed, 35 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/ecard.h b/include/asm-arm/ecard.h index 684fe064523..5e22881a630 100644 --- a/include/asm-arm/ecard.h +++ b/include/asm-arm/ecard.h @@ -85,19 +85,6 @@ #define MAX_ECARDS 9 -typedef enum { /* Cards address space */ - ECARD_IOC, - ECARD_MEMC, - ECARD_EASI -} card_type_t; - -typedef enum { /* Speed for ECARD_IOC space */ - ECARD_SLOW = 0, - ECARD_MEDIUM = 1, - ECARD_FAST = 2, - ECARD_SYNC = 3 -} card_speed_t; - struct ecard_id { /* Card ID structure */ unsigned short manufacturer; unsigned short product; @@ -189,16 +176,6 @@ struct in_chunk_dir { } d; }; -/* - * ecard_claim: claim an expansion card entry - */ -#define ecard_claim(ec) ((ec)->claimed = 1) - -/* - * ecard_release: release an expansion card entry - */ -#define ecard_release(ec) ((ec)->claimed = 0) - /* * Read a chunk from an expansion card * cd : where to put read data @@ -208,18 +185,6 @@ struct in_chunk_dir { */ extern int ecard_readchunk (struct in_chunk_dir *cd, struct expansion_card *ec, int id, int num); -/* - * Obtain the address of a card. This returns the "old style" address - * and should no longer be used. - */ -static inline unsigned int __deprecated -ecard_address(struct expansion_card *ec, card_type_t type, card_speed_t speed) -{ - extern unsigned int __ecard_address(struct expansion_card *, - card_type_t, card_speed_t); - return __ecard_address(ec, type, speed); -} - /* * Request and release ecard resources */ -- cgit v1.2.3 From 3c093f9f182eef6a8dc535f2c62b36a0320d0db1 Mon Sep 17 00:00:00 2001 From: Vegard Nossum Date: Mon, 9 Jun 2008 16:24:10 -0700 Subject: [ARM] fix header guards Acked-by: Dan Williams Signed-off-by: Vegard Nossum Signed-off-by: Andrew Morton Signed-off-by: Russell King --- include/asm-arm/arch-iop13xx/dma.h | 2 +- include/asm-arm/arch-msm/irqs.h | 1 + include/asm-arm/arch-msm/timex.h | 1 + 3 files changed, 3 insertions(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-iop13xx/dma.h b/include/asm-arm/arch-iop13xx/dma.h index 2e15da53ff7..d79846fbb39 100644 --- a/include/asm-arm/arch-iop13xx/dma.h +++ b/include/asm-arm/arch-iop13xx/dma.h @@ -1,3 +1,3 @@ #ifndef _IOP13XX_DMA_H -#define _IOP13XX_DMA_H_ +#define _IOP13XX_DMA_H #endif diff --git a/include/asm-arm/arch-msm/irqs.h b/include/asm-arm/arch-msm/irqs.h index 565430cfaa7..e62a108b185 100644 --- a/include/asm-arm/arch-msm/irqs.h +++ b/include/asm-arm/arch-msm/irqs.h @@ -15,6 +15,7 @@ */ #ifndef __ASM_ARCH_MSM_IRQS_H +#define __ASM_ARCH_MSM_IRQS_H /* MSM ARM11 Interrupt Numbers */ /* See 80-VE113-1 A, pp219-221 */ diff --git a/include/asm-arm/arch-msm/timex.h b/include/asm-arm/arch-msm/timex.h index 154b23fb359..8724487ab4c 100644 --- a/include/asm-arm/arch-msm/timex.h +++ b/include/asm-arm/arch-msm/timex.h @@ -14,6 +14,7 @@ */ #ifndef __ASM_ARCH_MSM_TIMEX_H +#define __ASM_ARCH_MSM_TIMEX_H #define CLOCK_TICK_RATE 1000000 -- cgit v1.2.3 From 826cbdaff29764bb6928c715c6a025e49469dda9 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Fri, 13 Jun 2008 10:28:36 +0100 Subject: [ARM] 5092/1: Fix the I-cache invalidation on ARMv6 and later CPUs This patch adds the I-cache invalidation in update_mmu_cache if the corresponding vma is marked as executable. It also invalidates the I-cache if a thread migrates to a CPU it never ran on. Signed-off-by: Catalin Marinas Signed-off-by: Russell King --- include/asm-arm/cacheflush.h | 7 +++++++ include/asm-arm/mmu_context.h | 5 +++++ 2 files changed, 12 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/cacheflush.h b/include/asm-arm/cacheflush.h index 759a97b56ee..559fb4af1f6 100644 --- a/include/asm-arm/cacheflush.h +++ b/include/asm-arm/cacheflush.h @@ -410,6 +410,13 @@ extern void flush_dcache_page(struct page *); extern void __flush_dcache_page(struct address_space *mapping, struct page *page); +static inline void __flush_icache_all(void) +{ + asm("mcr p15, 0, %0, c7, c5, 0 @ invalidate I-cache\n" + : + : "r" (0)); +} + #define ARCH_HAS_FLUSH_ANON_PAGE static inline void flush_anon_page(struct vm_area_struct *vma, struct page *page, unsigned long vmaddr) diff --git a/include/asm-arm/mmu_context.h b/include/asm-arm/mmu_context.h index 6913d02ca5d..91b9dfdfed5 100644 --- a/include/asm-arm/mmu_context.h +++ b/include/asm-arm/mmu_context.h @@ -97,6 +97,11 @@ switch_mm(struct mm_struct *prev, struct mm_struct *next, #ifdef CONFIG_MMU unsigned int cpu = smp_processor_id(); +#ifdef CONFIG_SMP + /* check for possible thread migration */ + if (!cpus_empty(next->cpu_vm_mask) && !cpu_isset(cpu, next->cpu_vm_mask)) + __flush_icache_all(); +#endif if (!cpu_test_and_set(cpu, next->cpu_vm_mask) || prev != next) { check_context(next); cpu_switch_mm(next->pgd, next); -- cgit v1.2.3 From f7def13ed0775ee506c62a8612a124dce1776ac2 Mon Sep 17 00:00:00 2001 From: Paulius Zaleckas Date: Wed, 25 Jun 2008 13:25:13 +0100 Subject: [ARM] 5122/1: imx_dma_request_by_prio simpilfication imx_dma_request_by_prio can return channel number by itself. No need to supply variable address through parameters. Also converted all drivers using this function. Signed-off-by: Paulius Zaleckas Acked-by: Sascha Hauer Signed-off-by: Russell King --- include/asm-arm/arch-imx/imx-dma.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-imx/imx-dma.h b/include/asm-arm/arch-imx/imx-dma.h index 5b1066da4e1..44d89c35539 100644 --- a/include/asm-arm/arch-imx/imx-dma.h +++ b/include/asm-arm/arch-imx/imx-dma.h @@ -88,7 +88,7 @@ int imx_dma_request(imx_dmach_t dma_ch, const char *name); void imx_dma_free(imx_dmach_t dma_ch); -int imx_dma_request_by_prio(imx_dmach_t *pdma_ch, const char *name, imx_dma_prio prio); +imx_dmach_t imx_dma_request_by_prio(const char *name, imx_dma_prio prio); #endif /* _ASM_ARCH_IMX_DMA_H */ -- cgit v1.2.3 From f348a2a2817e9d24b1edd4befc9659ec83501ca5 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 3 Jul 2008 11:24:25 +0100 Subject: [ARM] S3C24XX: Add gpiolib support Add support for gpilib on all S3C24XX platforms. Signed-off-by: Ben Dooks --- include/asm-arm/arch-s3c2410/gpio.h | 74 ++++++------------------------------- 1 file changed, 12 insertions(+), 62 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-s3c2410/gpio.h b/include/asm-arm/arch-s3c2410/gpio.h index 7583895fd33..18e10d2c35e 100644 --- a/include/asm-arm/arch-s3c2410/gpio.h +++ b/include/asm-arm/arch-s3c2410/gpio.h @@ -1,68 +1,18 @@ -/* - * linux/include/asm-arm/arch-s3c2410/gpio.h +/* linux/include/asm-arm/arch-s3c2410/gpio.h * - * S3C2410 GPIO wrappers for arch-neutral GPIO calls + * Copyright (c) 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks * - * Written by Philipp Zabel + * S3C2410 - GPIO lib support * * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -#ifndef __ASM_ARCH_S3C2410_GPIO_H -#define __ASM_ARCH_S3C2410_GPIO_H - -#include -#include -#include - -static inline int gpio_request(unsigned gpio, const char *label) -{ - return 0; -} - -static inline void gpio_free(unsigned gpio) -{ - return; -} - -static inline int gpio_direction_input(unsigned gpio) -{ - s3c2410_gpio_cfgpin(gpio, S3C2410_GPIO_INPUT); - return 0; -} - -static inline int gpio_direction_output(unsigned gpio, int value) -{ - s3c2410_gpio_cfgpin(gpio, S3C2410_GPIO_OUTPUT); - /* REVISIT can we write the value first, to avoid glitching? */ - s3c2410_gpio_setpin(gpio, value); - return 0; -} - -#define gpio_get_value(gpio) s3c2410_gpio_getpin(gpio) -#define gpio_set_value(gpio,value) s3c2410_gpio_setpin(gpio, value) - -#include /* cansleep wrappers */ - -#ifdef CONFIG_CPU_S3C2400 -#define gpio_to_irq(gpio) s3c2400_gpio_getirq(gpio) -#else -#define gpio_to_irq(gpio) s3c2410_gpio_getirq(gpio) -#endif + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ -/* FIXME implement irq_to_gpio() */ +#define gpio_get_value __gpio_get_value +#define gpio_set_value __gpio_set_value +#define gpio_cansleep __gpio_cansleep -#endif +#include -- cgit v1.2.3 From b4b68f8cfaf583945019e41674cfa858c83316c3 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 3 Jul 2008 11:24:26 +0100 Subject: [ARM] S3C24XX: Add PWM timer MUX defines Add timer defines for the MUX settings for each of the PWM timers to add to the per-timer defines already in the file. Signed-off-by: Ben Dooks --- include/asm-arm/plat-s3c/regs-timer.h | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-s3c/regs-timer.h b/include/asm-arm/plat-s3c/regs-timer.h index 8b0d594397b..b5bc692f348 100644 --- a/include/asm-arm/plat-s3c/regs-timer.h +++ b/include/asm-arm/plat-s3c/regs-timer.h @@ -65,6 +65,15 @@ #define S3C2410_TCFG1_MUX0_TCLK0 (4<<0) #define S3C2410_TCFG1_MUX0_MASK (15<<0) +#define S3C2410_TCFG1_MUX_DIV2 (0<<0) +#define S3C2410_TCFG1_MUX_DIV4 (1<<0) +#define S3C2410_TCFG1_MUX_DIV8 (2<<0) +#define S3C2410_TCFG1_MUX_DIV16 (3<<0) +#define S3C2410_TCFG1_MUX_TCLK (4<<0) +#define S3C2410_TCFG1_MUX_MASK (15<<0) + +#define S3C2410_TCFG1_SHIFT(x) ((x) * 4) + /* for each timer, we have an count buffer, an compare buffer and * an observation buffer */ -- cgit v1.2.3 From d5c52922b618aa6ddd6b5ebebc8d0a5ec9a20f10 Mon Sep 17 00:00:00 2001 From: Matthieu Castet Date: Thu, 3 Jul 2008 11:24:45 +0100 Subject: [ARM] S3C2412: Correct parents for EREFCLK and UREFCLK For s3c2412, set parent for clk_erefclk and clk_urefclk. This allow for example to use xtal or extclk for i2s clock. Signed-off-by: Ben Dooks Signed-off-by: Matthieu Castet --- include/asm-arm/arch-s3c2410/regs-clock.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-s3c2410/regs-clock.h b/include/asm-arm/arch-s3c2410/regs-clock.h index ecae9e7f5e4..37661358b42 100644 --- a/include/asm-arm/arch-s3c2410/regs-clock.h +++ b/include/asm-arm/arch-s3c2410/regs-clock.h @@ -189,6 +189,8 @@ s3c2410_get_pll(unsigned int pllval, unsigned int baseclk) #define S3C2412_CLKSRC_I2SCLK_MPLL (1<<9) #define S3C2412_CLKSRC_USBCLK_HCLK (1<<10) #define S3C2412_CLKSRC_CAMCLK_HCLK (1<<11) +#define S3C2412_CLKSRC_UREFCLK_EXTCLK (1<<12) +#define S3C2412_CLKSRC_EREFCLK_EXTCLK (1<<14) #endif /* CONFIG_CPU_S3C2412 | CONFIG_CPU_S3C2413 */ -- cgit v1.2.3 From 6fc601e37bbb4045ee0afefc76b64284ea800c89 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 1 Jul 2008 13:17:24 +0100 Subject: [ARM] S3C24XX: PWM API support. Add support for PWM in the S3C24XX series of SoC via the PWM API. Signed-off-by: Ben Dooks --- include/asm-arm/plat-s3c24xx/devs.h | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-s3c24xx/devs.h b/include/asm-arm/plat-s3c24xx/devs.h index f9d6f0317bc..badaac9d64a 100644 --- a/include/asm-arm/plat-s3c24xx/devs.h +++ b/include/asm-arm/plat-s3c24xx/devs.h @@ -21,6 +21,8 @@ extern struct s3c24xx_uart_resources s3c2410_uart_resources[]; extern struct platform_device *s3c24xx_uart_devs[]; extern struct platform_device *s3c24xx_uart_src[]; +extern struct platform_device s3c_device_timer[]; + extern struct platform_device s3c_device_usb; extern struct platform_device s3c_device_lcd; extern struct platform_device s3c_device_wdt; @@ -36,11 +38,6 @@ extern struct platform_device s3c_device_spi1; extern struct platform_device s3c_device_nand; -extern struct platform_device s3c_device_timer0; -extern struct platform_device s3c_device_timer1; -extern struct platform_device s3c_device_timer2; -extern struct platform_device s3c_device_timer3; - extern struct platform_device s3c_device_usbgadget; /* s3c2440 specific devices */ -- cgit v1.2.3 From 63dd10846d4917534e9ec7bddf43be786effe8b8 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Sat, 5 Jul 2008 10:02:43 +0200 Subject: MXC: do not include board specific header from architecture include do not include board-mx31ads.h from hardware.h, instead include it directly only where needed. Signed-off-by: Sascha Hauer --- include/asm-arm/arch-mxc/hardware.h | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/hardware.h b/include/asm-arm/arch-mxc/hardware.h index e87ff0679d5..4ed2d8072d0 100644 --- a/include/asm-arm/arch-mxc/hardware.h +++ b/include/asm-arm/arch-mxc/hardware.h @@ -1,11 +1,20 @@ /* - * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved. - */ - -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. + * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright 2008 Juergen Beisert, kernel@pengutronix.de + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. */ #ifndef __ASM_ARCH_MXC_HARDWARE_H__ @@ -19,13 +28,4 @@ #include -/* - * --------------------------------------------------------------------------- - * Board specific defines - * --------------------------------------------------------------------------- - */ -#ifdef CONFIG_MACH_MX31ADS -# include -#endif - #endif /* __ASM_ARCH_MXC_HARDWARE_H__ */ -- cgit v1.2.3 From 2582d8c1655f2eda42d5358a242b256fd6e88571 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Sat, 5 Jul 2008 10:02:45 +0200 Subject: IMX UART: Add board specific init/exit functions Add platform specific init functions. Also rename the struct platform_device dev into pdev. Signed-off-by: Sascha Hauer --- include/asm-arm/arch-imx/imx-uart.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-imx/imx-uart.h b/include/asm-arm/arch-imx/imx-uart.h index 3a685e1780e..d54eb1d4802 100644 --- a/include/asm-arm/arch-imx/imx-uart.h +++ b/include/asm-arm/arch-imx/imx-uart.h @@ -4,6 +4,8 @@ #define IMXUART_HAVE_RTSCTS (1<<0) struct imxuart_platform_data { + int (*init)(struct platform_device *pdev); + void (*exit)(struct platform_device *pdev); unsigned int flags; }; -- cgit v1.2.3 From 38a41fdf94c449c165213e4665c3f8a0d30f8aba Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Sat, 5 Jul 2008 10:02:46 +0200 Subject: IMX: introduce clock API This patch introduces the clock API for i.MX and converts all in-Kernel drivers to use it. Signed-off-by: Sascha Hauer --- include/asm-arm/arch-imx/hardware.h | 8 -------- 1 file changed, 8 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-imx/hardware.h b/include/asm-arm/arch-imx/hardware.h index adffb6acf42..6542ca5e8c3 100644 --- a/include/asm-arm/arch-imx/hardware.h +++ b/include/asm-arm/arch-imx/hardware.h @@ -73,14 +73,6 @@ */ extern void imx_gpio_mode( int gpio_mode ); -/* get frequencies in Hz */ -extern unsigned int imx_get_system_clk(void); -extern unsigned int imx_get_mcu_clk(void); -extern unsigned int imx_get_perclk1(void); /* UART[12], Timer[12], PWM */ -extern unsigned int imx_get_perclk2(void); /* LCD, SD, SPI[12] */ -extern unsigned int imx_get_perclk3(void); /* SSI */ -extern unsigned int imx_get_hclk(void); /* SDRAM, CSI, Memory Stick,*/ - /* I2C, DMA */ #endif #define MAXIRQNUM 62 -- cgit v1.2.3 From c0db2ea4e366c94dd3f880928c02534156e3d1b9 Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:02:47 +0200 Subject: MXC family: Add clock handling Internal clock path handling for the mxc CPUs. Changed against the original Freescale code (and against clocklib for example): - clock rate is always calculated whenever one ask for the current rate (means struct clk has no more a member called "rate"). So switching the PLL base frequency will propagate immediately to all other clocks that are depending on this frequency. Signed-off-by: Juergen Beisert --- include/asm-arm/arch-mxc/clock.h | 67 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 67 insertions(+) create mode 100644 include/asm-arm/arch-mxc/clock.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/clock.h b/include/asm-arm/arch-mxc/clock.h new file mode 100644 index 00000000000..24caa2b7c91 --- /dev/null +++ b/include/asm-arm/arch-mxc/clock.h @@ -0,0 +1,67 @@ +/* + * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright 2008 Juergen Beisert, kernel@pengutronix.de + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef __ASM_ARCH_MXC_CLOCK_H__ +#define __ASM_ARCH_MXC_CLOCK_H__ + +#ifndef __ASSEMBLY__ +#include + +struct module; + +struct clk { + struct list_head node; + struct module *owner; + const char *name; + int id; + /* Source clock this clk depends on */ + struct clk *parent; + /* Secondary clock to enable/disable with this clock */ + struct clk *secondary; + /* Reference count of clock enable/disable */ + __s8 usecount; + /* Register bit position for clock's enable/disable control. */ + u8 enable_shift; + /* Register address for clock's enable/disable control. */ + u32 enable_reg; + u32 flags; + /* get the current clock rate (always a fresh value) */ + unsigned long (*get_rate) (struct clk *); + /* Function ptr to set the clock to a new rate. The rate must match a + supported rate returned from round_rate. Leave blank if clock is not + programmable */ + int (*set_rate) (struct clk *, unsigned long); + /* Function ptr to round the requested clock rate to the nearest + supported rate that is less than or equal to the requested rate. */ + unsigned long (*round_rate) (struct clk *, unsigned long); + /* Function ptr to enable the clock. Leave blank if clock can not + be gated. */ + int (*enable) (struct clk *); + /* Function ptr to disable the clock. Leave blank if clock can not + be gated. */ + void (*disable) (struct clk *); + /* Function ptr to set the parent clock of the clock. */ + int (*set_parent) (struct clk *, struct clk *); +}; + +int clk_register(struct clk *clk); +void clk_unregister(struct clk *clk); + +#endif /* __ASSEMBLY__ */ +#endif /* __ASM_ARCH_MXC_CLOCK_H__ */ -- cgit v1.2.3 From df1bf4bdb2a3a26d4bde8ae1aefc16385dd4898f Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Sat, 5 Jul 2008 10:02:48 +0200 Subject: i.MX3: introduce clock API This patch introduces the clock API for for arch-mxc Signed-off-by: Sascha Hauer --- include/asm-arm/arch-mxc/common.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/common.h b/include/asm-arm/arch-mxc/common.h index 23b4350edbd..c6d4aa36063 100644 --- a/include/asm-arm/arch-mxc/common.h +++ b/include/asm-arm/arch-mxc/common.h @@ -16,5 +16,6 @@ struct sys_timer; extern void mxc_map_io(void); extern void mxc_init_irq(void); extern struct sys_timer mxc_timer; +extern int mxc_clocks_init(unsigned long fref); #endif -- cgit v1.2.3 From e3d13ff4b9d3b05d7a969153e2c049548e25deea Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Sat, 5 Jul 2008 10:02:48 +0200 Subject: mxc: add MX3 support for i.MX internal UART driver This patch adds MX3 support for the i.MX internal uart driver. Signed-off-by: Sascha Hauer --- include/asm-arm/arch-mxc/imx-uart.h | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) create mode 100644 include/asm-arm/arch-mxc/imx-uart.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/imx-uart.h b/include/asm-arm/arch-mxc/imx-uart.h new file mode 100644 index 00000000000..83fb72c4048 --- /dev/null +++ b/include/asm-arm/arch-mxc/imx-uart.h @@ -0,0 +1,32 @@ +/* + * Copyright (C) 2008 by Sascha Hauer + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef ASMARM_ARCH_UART_H +#define ASMARM_ARCH_UART_H + +#define IMXUART_HAVE_RTSCTS (1<<0) + +struct imxuart_platform_data { + int (*init)(struct platform_device *pdev); + int (*exit)(struct platform_device *pdev); + unsigned int flags; +}; + +int __init imx_init_uart(int uart_no, struct imxuart_platform_data *pdata); + +#endif -- cgit v1.2.3 From 07bd1a6cc7cbb3f373fbe49b204c6cde5e9155fc Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:02:49 +0200 Subject: MXC arch: Add gpio support for the whole platform This patch bases on the one from Daniel Mack. The most important change to Daniel's patch is to be more generic. This gpio routine supports at least the i.MX27 and i.MX31 processors. Signed-off-by: Juergen Beisert Acked-by: Daniel Mack --- include/asm-arm/arch-mxc/common.h | 1 + include/asm-arm/arch-mxc/gpio.h | 42 +++++++++++++++++++++++++++++++++++++++ include/asm-arm/arch-mxc/mx31.h | 19 ++++++++++++++++++ 3 files changed, 62 insertions(+) create mode 100644 include/asm-arm/arch-mxc/gpio.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/common.h b/include/asm-arm/arch-mxc/common.h index c6d4aa36063..8774783ed98 100644 --- a/include/asm-arm/arch-mxc/common.h +++ b/include/asm-arm/arch-mxc/common.h @@ -17,5 +17,6 @@ extern void mxc_map_io(void); extern void mxc_init_irq(void); extern struct sys_timer mxc_timer; extern int mxc_clocks_init(unsigned long fref); +extern int mxc_register_gpios(void); #endif diff --git a/include/asm-arm/arch-mxc/gpio.h b/include/asm-arm/arch-mxc/gpio.h new file mode 100644 index 00000000000..d393e15f5a6 --- /dev/null +++ b/include/asm-arm/arch-mxc/gpio.h @@ -0,0 +1,42 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright 2008 Juergen Beisert, kernel@pengutronix.de + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. + */ + +#ifndef __ASM_ARCH_MXC_GPIO_H__ +#define __ASM_ARCH_MXC_GPIO_H__ + +#include +#include + +/* use gpiolib dispatchers */ +#define gpio_get_value __gpio_get_value +#define gpio_set_value __gpio_set_value +#define gpio_cansleep __gpio_cansleep + +#define gpio_to_irq(gpio) (MXC_MAX_INT_LINES + (gpio)) +#define irq_to_gpio(irq) ((irq) - MXC_MAX_INT_LINES) + +struct mxc_gpio_port { + void __iomem *base; + int irq; + int virtual_irq_start; + struct gpio_chip chip; +}; + +int mxc_gpio_init(struct mxc_gpio_port*, int); + +#endif diff --git a/include/asm-arm/arch-mxc/mx31.h b/include/asm-arm/arch-mxc/mx31.h index 36a1af495bb..98e6a4cd1ea 100644 --- a/include/asm-arm/arch-mxc/mx31.h +++ b/include/asm-arm/arch-mxc/mx31.h @@ -347,6 +347,25 @@ #define SYSTEM_REV_MIN CHIP_REV_1_0 #define SYSTEM_REV_NUM 3 +/* gpio and gpio based interrupt handling */ +#define GPIO_DR 0x00 +#define GPIO_GDIR 0x04 +#define GPIO_PSR 0x08 +#define GPIO_ICR1 0x0C +#define GPIO_ICR2 0x10 +#define GPIO_IMR 0x14 +#define GPIO_ISR 0x18 +#define GPIO_INT_LOW_LEV 0x0 +#define GPIO_INT_HIGH_LEV 0x1 +#define GPIO_INT_RISE_EDGE 0x2 +#define GPIO_INT_FALL_EDGE 0x3 +#define GPIO_INT_NONE 0x4 + +/* Mandatory defines used globally */ + +/* this CPU supports up to 96 GPIOs */ +#define ARCH_NR_GPIOS 96 + #if !defined(__ASSEMBLY__) && !defined(__MXC_BOOT_UNCOMPRESS) /* this is a i.MX31 CPU */ -- cgit v1.2.3 From 90292ea60f1c730efb9fea02b2e12676da89ebef Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Sat, 5 Jul 2008 10:02:50 +0200 Subject: MXC: add io multiplexing functions for mx3 This patch adds functions to use the io multiplexer on mx3 platforms. Signed-off-by: Sascha Hauer --- include/asm-arm/arch-mxc/iomux-mx3.h | 501 +++++++++++++++++++++++++++++++++++ 1 file changed, 501 insertions(+) create mode 100644 include/asm-arm/arch-mxc/iomux-mx3.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/iomux-mx3.h b/include/asm-arm/arch-mxc/iomux-mx3.h new file mode 100644 index 00000000000..7509e7692f0 --- /dev/null +++ b/include/asm-arm/arch-mxc/iomux-mx3.h @@ -0,0 +1,501 @@ +/* + * Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright (C) 2008 by Sascha Hauer + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef __MACH_MX31_IOMUX_H__ +#define __MACH_MX31_IOMUX_H__ + +#include + +/* + * various IOMUX output functions + */ + +#define IOMUX_OCONFIG_GPIO (0 << 4) /* used as GPIO */ +#define IOMUX_OCONFIG_FUNC (1 << 4) /* used as function */ +#define IOMUX_OCONFIG_ALT1 (2 << 4) /* used as alternate function 1 */ +#define IOMUX_OCONFIG_ALT2 (3 << 4) /* used as alternate function 2 */ +#define IOMUX_OCONFIG_ALT3 (4 << 4) /* used as alternate function 3 */ +#define IOMUX_OCONFIG_ALT4 (5 << 4) /* used as alternate function 4 */ +#define IOMUX_OCONFIG_ALT5 (6 << 4) /* used as alternate function 5 */ +#define IOMUX_OCONFIG_ALT6 (7 << 4) /* used as alternate function 6 */ +#define IOMUX_ICONFIG_NONE 0 /* not configured for input */ +#define IOMUX_ICONFIG_GPIO 1 /* used as GPIO */ +#define IOMUX_ICONFIG_FUNC 2 /* used as function */ +#define IOMUX_ICONFIG_ALT1 4 /* used as alternate function 1 */ +#define IOMUX_ICONFIG_ALT2 8 /* used as alternate function 2 */ + +#define IOMUX_CONFIG_GPIO (IOMUX_OCONFIG_GPIO | IOMUX_ICONFIG_GPIO) +#define IOMUX_CONFIG_FUNC (IOMUX_OCONFIG_FUNC | IOMUX_ICONFIG_FUNC) +#define IOMUX_CONFIG_ALT1 (IOMUX_OCONFIG_ALT1 | IOMUX_ICONFIG_ALT1) +#define IOMUX_CONFIG_ALT2 (IOMUX_OCONFIG_ALT2 | IOMUX_ICONFIG_ALT2) + +/* + * various IOMUX pad functions + */ +enum iomux_pad_config { + PAD_CTL_NOLOOPBACK = 0x0 << 9, + PAD_CTL_LOOPBACK = 0x1 << 9, + PAD_CTL_PKE_NONE = 0x0 << 8, + PAD_CTL_PKE_ENABLE = 0x1 << 8, + PAD_CTL_PUE_KEEPER = 0x0 << 7, + PAD_CTL_PUE_PUD = 0x1 << 7, + PAD_CTL_100K_PD = 0x0 << 5, + PAD_CTL_100K_PU = 0x1 << 5, + PAD_CTL_47K_PU = 0x2 << 5, + PAD_CTL_22K_PU = 0x3 << 5, + PAD_CTL_HYS_CMOS = 0x0 << 4, + PAD_CTL_HYS_SCHMITZ = 0x1 << 4, + PAD_CTL_ODE_CMOS = 0x0 << 3, + PAD_CTL_ODE_OpenDrain = 0x1 << 3, + PAD_CTL_DRV_NORMAL = 0x0 << 1, + PAD_CTL_DRV_HIGH = 0x1 << 1, + PAD_CTL_DRV_MAX = 0x2 << 1, + PAD_CTL_SRE_SLOW = 0x0 << 0, + PAD_CTL_SRE_FAST = 0x1 << 0 +}; + +/* + * various IOMUX general purpose functions + */ +enum iomux_gp_func { + MUX_PGP_FIRI = 1 << 0, + MUX_DDR_MODE = 1 << 1, + MUX_PGP_CSPI_BB = 1 << 2, + MUX_PGP_ATA_1 = 1 << 3, + MUX_PGP_ATA_2 = 1 << 4, + MUX_PGP_ATA_3 = 1 << 5, + MUX_PGP_ATA_4 = 1 << 6, + MUX_PGP_ATA_5 = 1 << 7, + MUX_PGP_ATA_6 = 1 << 8, + MUX_PGP_ATA_7 = 1 << 9, + MUX_PGP_ATA_8 = 1 << 10, + MUX_PGP_UH2 = 1 << 11, + MUX_SDCTL_CSD0_SEL = 1 << 12, + MUX_SDCTL_CSD1_SEL = 1 << 13, + MUX_CSPI1_UART3 = 1 << 14, + MUX_EXTDMAREQ2_MBX_SEL = 1 << 15, + MUX_TAMPER_DETECT_EN = 1 << 16, + MUX_PGP_USB_4WIRE = 1 << 17, + MUX_PGB_USB_COMMON = 1 << 18, + MUX_SDHC_MEMSTICK1 = 1 << 19, + MUX_SDHC_MEMSTICK2 = 1 << 20, + MUX_PGP_SPLL_BYP = 1 << 21, + MUX_PGP_UPLL_BYP = 1 << 22, + MUX_PGP_MSHC1_CLK_SEL = 1 << 23, + MUX_PGP_MSHC2_CLK_SEL = 1 << 24, + MUX_CSPI3_UART5_SEL = 1 << 25, + MUX_PGP_ATA_9 = 1 << 26, + MUX_PGP_USB_SUSPEND = 1 << 27, + MUX_PGP_USB_OTG_LOOPBACK = 1 << 28, + MUX_PGP_USB_HS1_LOOPBACK = 1 << 29, + MUX_PGP_USB_HS2_LOOPBACK = 1 << 30, + MUX_CLKO_DDR_MODE = 1 << 31, +}; + +/* + * This function enables/disables the general purpose function for a particular + * signal. + */ +void iomux_config_gpr(enum iomux_gp_func , bool); + +/* + * set the mode for a IOMUX pin. + */ +int mxc_iomux_mode(unsigned int); + +/* + * This function enables/disables the general purpose function for a particular + * signal. + */ +void mxc_iomux_set_gpr(enum iomux_gp_func, bool); + +#define IOMUX_PADNUM_MASK 0x1ff +#define IOMUX_GPIONUM_SHIFT 9 +#define IOMUX_GPIONUM_MASK (0xff << IOMUX_GPIONUM_SHIFT) +#define IOMUX_MODE_SHIFT 17 +#define IOMUX_MODE_MASK (0xff << IOMUX_MODE_SHIFT) + +#define IOMUX_PIN(gpionum, padnum) \ + (((gpionum << IOMUX_GPIONUM_SHIFT) & IOMUX_GPIONUM_MASK) | \ + (padnum & IOMUX_PADNUM_MASK)) + +#define IOMUX_MODE(pin, mode) (pin | mode << IOMUX_MODE_SHIFT) + +#define IOMUX_TO_GPIO(iomux_pin) \ + ((iomux_pin & IOMUX_GPIONUM_MASK) >> IOMUX_GPIONUM_SHIFT) +#define IOMUX_TO_IRQ(iomux_pin) \ + (((iomux_pin & IOMUX_GPIONUM_MASK) >> IOMUX_GPIONUM_SHIFT) + \ + MXC_GPIO_INT_BASE) + +/* + * This enumeration is constructed based on the Section + * "sw_pad_ctl & sw_mux_ctl details" of the MX31 IC Spec. Each enumerated + * value is constructed based on the rules described above. + */ + +enum iomux_pins { + MX31_PIN_TTM_PAD = IOMUX_PIN(0xff, 0), + MX31_PIN_CSPI3_SPI_RDY = IOMUX_PIN(0xff, 1), + MX31_PIN_CSPI3_SCLK = IOMUX_PIN(0xff, 2), + MX31_PIN_CSPI3_MISO = IOMUX_PIN(0xff, 3), + MX31_PIN_CSPI3_MOSI = IOMUX_PIN(0xff, 4), + MX31_PIN_CLKSS = IOMUX_PIN(0xff, 5), + MX31_PIN_CE_CONTROL = IOMUX_PIN(0xff, 6), + MX31_PIN_ATA_RESET_B = IOMUX_PIN(95, 7), + MX31_PIN_ATA_DMACK = IOMUX_PIN(94, 8), + MX31_PIN_ATA_DIOW = IOMUX_PIN(93, 9), + MX31_PIN_ATA_DIOR = IOMUX_PIN(92, 10), + MX31_PIN_ATA_CS1 = IOMUX_PIN(91, 11), + MX31_PIN_ATA_CS0 = IOMUX_PIN(90, 12), + MX31_PIN_SD1_DATA3 = IOMUX_PIN(63, 13), + MX31_PIN_SD1_DATA2 = IOMUX_PIN(62, 14), + MX31_PIN_SD1_DATA1 = IOMUX_PIN(61, 15), + MX31_PIN_SD1_DATA0 = IOMUX_PIN(60, 16), + MX31_PIN_SD1_CLK = IOMUX_PIN(59, 17), + MX31_PIN_SD1_CMD = IOMUX_PIN(58, 18), + MX31_PIN_D3_SPL = IOMUX_PIN(0xff, 19), + MX31_PIN_D3_CLS = IOMUX_PIN(0xff, 20), + MX31_PIN_D3_REV = IOMUX_PIN(0xff, 21), + MX31_PIN_CONTRAST = IOMUX_PIN(0xff, 22), + MX31_PIN_VSYNC3 = IOMUX_PIN(0xff, 23), + MX31_PIN_READ = IOMUX_PIN(0xff, 24), + MX31_PIN_WRITE = IOMUX_PIN(0xff, 25), + MX31_PIN_PAR_RS = IOMUX_PIN(0xff, 26), + MX31_PIN_SER_RS = IOMUX_PIN(89, 27), + MX31_PIN_LCS1 = IOMUX_PIN(88, 28), + MX31_PIN_LCS0 = IOMUX_PIN(87, 29), + MX31_PIN_SD_D_CLK = IOMUX_PIN(86, 30), + MX31_PIN_SD_D_IO = IOMUX_PIN(85, 31), + MX31_PIN_SD_D_I = IOMUX_PIN(84, 32), + MX31_PIN_DRDY0 = IOMUX_PIN(0xff, 33), + MX31_PIN_FPSHIFT = IOMUX_PIN(0xff, 34), + MX31_PIN_HSYNC = IOMUX_PIN(0xff, 35), + MX31_PIN_VSYNC0 = IOMUX_PIN(0xff, 36), + MX31_PIN_LD17 = IOMUX_PIN(0xff, 37), + MX31_PIN_LD16 = IOMUX_PIN(0xff, 38), + MX31_PIN_LD15 = IOMUX_PIN(0xff, 39), + MX31_PIN_LD14 = IOMUX_PIN(0xff, 40), + MX31_PIN_LD13 = IOMUX_PIN(0xff, 41), + MX31_PIN_LD12 = IOMUX_PIN(0xff, 42), + MX31_PIN_LD11 = IOMUX_PIN(0xff, 43), + MX31_PIN_LD10 = IOMUX_PIN(0xff, 44), + MX31_PIN_LD9 = IOMUX_PIN(0xff, 45), + MX31_PIN_LD8 = IOMUX_PIN(0xff, 46), + MX31_PIN_LD7 = IOMUX_PIN(0xff, 47), + MX31_PIN_LD6 = IOMUX_PIN(0xff, 48), + MX31_PIN_LD5 = IOMUX_PIN(0xff, 49), + MX31_PIN_LD4 = IOMUX_PIN(0xff, 50), + MX31_PIN_LD3 = IOMUX_PIN(0xff, 51), + MX31_PIN_LD2 = IOMUX_PIN(0xff, 52), + MX31_PIN_LD1 = IOMUX_PIN(0xff, 53), + MX31_PIN_LD0 = IOMUX_PIN(0xff, 54), + MX31_PIN_USBH2_DATA1 = IOMUX_PIN(0xff, 55), + MX31_PIN_USBH2_DATA0 = IOMUX_PIN(0xff, 56), + MX31_PIN_USBH2_NXT = IOMUX_PIN(0xff, 57), + MX31_PIN_USBH2_STP = IOMUX_PIN(0xff, 58), + MX31_PIN_USBH2_DIR = IOMUX_PIN(0xff, 59), + MX31_PIN_USBH2_CLK = IOMUX_PIN(0xff, 60), + MX31_PIN_USBOTG_DATA7 = IOMUX_PIN(0xff, 61), + MX31_PIN_USBOTG_DATA6 = IOMUX_PIN(0xff, 62), + MX31_PIN_USBOTG_DATA5 = IOMUX_PIN(0xff, 63), + MX31_PIN_USBOTG_DATA4 = IOMUX_PIN(0xff, 64), + MX31_PIN_USBOTG_DATA3 = IOMUX_PIN(0xff, 65), + MX31_PIN_USBOTG_DATA2 = IOMUX_PIN(0xff, 66), + MX31_PIN_USBOTG_DATA1 = IOMUX_PIN(0xff, 67), + MX31_PIN_USBOTG_DATA0 = IOMUX_PIN(0xff, 68), + MX31_PIN_USBOTG_NXT = IOMUX_PIN(0xff, 69), + MX31_PIN_USBOTG_STP = IOMUX_PIN(0xff, 70), + MX31_PIN_USBOTG_DIR = IOMUX_PIN(0xff, 71), + MX31_PIN_USBOTG_CLK = IOMUX_PIN(0xff, 72), + MX31_PIN_USB_BYP = IOMUX_PIN(31, 73), + MX31_PIN_USB_OC = IOMUX_PIN(30, 74), + MX31_PIN_USB_PWR = IOMUX_PIN(29, 75), + MX31_PIN_SJC_MOD = IOMUX_PIN(0xff, 76), + MX31_PIN_DE_B = IOMUX_PIN(0xff, 77), + MX31_PIN_TRSTB = IOMUX_PIN(0xff, 78), + MX31_PIN_TDO = IOMUX_PIN(0xff, 79), + MX31_PIN_TDI = IOMUX_PIN(0xff, 80), + MX31_PIN_TMS = IOMUX_PIN(0xff, 81), + MX31_PIN_TCK = IOMUX_PIN(0xff, 82), + MX31_PIN_RTCK = IOMUX_PIN(0xff, 83), + MX31_PIN_KEY_COL7 = IOMUX_PIN(57, 84), + MX31_PIN_KEY_COL6 = IOMUX_PIN(56, 85), + MX31_PIN_KEY_COL5 = IOMUX_PIN(55, 86), + MX31_PIN_KEY_COL4 = IOMUX_PIN(54, 87), + MX31_PIN_KEY_COL3 = IOMUX_PIN(0xff, 88), + MX31_PIN_KEY_COL2 = IOMUX_PIN(0xff, 89), + MX31_PIN_KEY_COL1 = IOMUX_PIN(0xff, 90), + MX31_PIN_KEY_COL0 = IOMUX_PIN(0xff, 91), + MX31_PIN_KEY_ROW7 = IOMUX_PIN(53, 92), + MX31_PIN_KEY_ROW6 = IOMUX_PIN(52, 93), + MX31_PIN_KEY_ROW5 = IOMUX_PIN(51, 94), + MX31_PIN_KEY_ROW4 = IOMUX_PIN(50, 95), + MX31_PIN_KEY_ROW3 = IOMUX_PIN(0xff, 96), + MX31_PIN_KEY_ROW2 = IOMUX_PIN(0xff, 97), + MX31_PIN_KEY_ROW1 = IOMUX_PIN(0xff, 98), + MX31_PIN_KEY_ROW0 = IOMUX_PIN(0xff, 99), + MX31_PIN_BATT_LINE = IOMUX_PIN(49, 100), + MX31_PIN_CTS2 = IOMUX_PIN(0xff, 101), + MX31_PIN_RTS2 = IOMUX_PIN(0xff, 102), + MX31_PIN_TXD2 = IOMUX_PIN(28, 103), + MX31_PIN_RXD2 = IOMUX_PIN(27, 104), + MX31_PIN_DTR_DCE2 = IOMUX_PIN(48, 105), + MX31_PIN_DCD_DTE1 = IOMUX_PIN(47, 106), + MX31_PIN_RI_DTE1 = IOMUX_PIN(46, 107), + MX31_PIN_DSR_DTE1 = IOMUX_PIN(45, 108), + MX31_PIN_DTR_DTE1 = IOMUX_PIN(44, 109), + MX31_PIN_DCD_DCE1 = IOMUX_PIN(43, 110), + MX31_PIN_RI_DCE1 = IOMUX_PIN(42, 111), + MX31_PIN_DSR_DCE1 = IOMUX_PIN(41, 112), + MX31_PIN_DTR_DCE1 = IOMUX_PIN(40, 113), + MX31_PIN_CTS1 = IOMUX_PIN(39, 114), + MX31_PIN_RTS1 = IOMUX_PIN(38, 115), + MX31_PIN_TXD1 = IOMUX_PIN(37, 116), + MX31_PIN_RXD1 = IOMUX_PIN(36, 117), + MX31_PIN_CSPI2_SPI_RDY = IOMUX_PIN(0xff, 118), + MX31_PIN_CSPI2_SCLK = IOMUX_PIN(0xff, 119), + MX31_PIN_CSPI2_SS2 = IOMUX_PIN(0xff, 120), + MX31_PIN_CSPI2_SS1 = IOMUX_PIN(0xff, 121), + MX31_PIN_CSPI2_SS0 = IOMUX_PIN(0xff, 122), + MX31_PIN_CSPI2_MISO = IOMUX_PIN(0xff, 123), + MX31_PIN_CSPI2_MOSI = IOMUX_PIN(0xff, 124), + MX31_PIN_CSPI1_SPI_RDY = IOMUX_PIN(0xff, 125), + MX31_PIN_CSPI1_SCLK = IOMUX_PIN(0xff, 126), + MX31_PIN_CSPI1_SS2 = IOMUX_PIN(0xff, 127), + MX31_PIN_CSPI1_SS1 = IOMUX_PIN(0xff, 128), + MX31_PIN_CSPI1_SS0 = IOMUX_PIN(0xff, 129), + MX31_PIN_CSPI1_MISO = IOMUX_PIN(0xff, 130), + MX31_PIN_CSPI1_MOSI = IOMUX_PIN(0xff, 131), + MX31_PIN_SFS6 = IOMUX_PIN(26, 132), + MX31_PIN_SCK6 = IOMUX_PIN(25, 133), + MX31_PIN_SRXD6 = IOMUX_PIN(24, 134), + MX31_PIN_STXD6 = IOMUX_PIN(23, 135), + MX31_PIN_SFS5 = IOMUX_PIN(0xff, 136), + MX31_PIN_SCK5 = IOMUX_PIN(0xff, 137), + MX31_PIN_SRXD5 = IOMUX_PIN(22, 138), + MX31_PIN_STXD5 = IOMUX_PIN(21, 139), + MX31_PIN_SFS4 = IOMUX_PIN(0xff, 140), + MX31_PIN_SCK4 = IOMUX_PIN(0xff, 141), + MX31_PIN_SRXD4 = IOMUX_PIN(20, 142), + MX31_PIN_STXD4 = IOMUX_PIN(19, 143), + MX31_PIN_SFS3 = IOMUX_PIN(0xff, 144), + MX31_PIN_SCK3 = IOMUX_PIN(0xff, 145), + MX31_PIN_SRXD3 = IOMUX_PIN(18, 146), + MX31_PIN_STXD3 = IOMUX_PIN(17, 147), + MX31_PIN_I2C_DAT = IOMUX_PIN(0xff, 148), + MX31_PIN_I2C_CLK = IOMUX_PIN(0xff, 149), + MX31_PIN_CSI_PIXCLK = IOMUX_PIN(83, 150), + MX31_PIN_CSI_HSYNC = IOMUX_PIN(82, 151), + MX31_PIN_CSI_VSYNC = IOMUX_PIN(81, 152), + MX31_PIN_CSI_MCLK = IOMUX_PIN(80, 153), + MX31_PIN_CSI_D15 = IOMUX_PIN(79, 154), + MX31_PIN_CSI_D14 = IOMUX_PIN(78, 155), + MX31_PIN_CSI_D13 = IOMUX_PIN(77, 156), + MX31_PIN_CSI_D12 = IOMUX_PIN(76, 157), + MX31_PIN_CSI_D11 = IOMUX_PIN(75, 158), + MX31_PIN_CSI_D10 = IOMUX_PIN(74, 159), + MX31_PIN_CSI_D9 = IOMUX_PIN(73, 160), + MX31_PIN_CSI_D8 = IOMUX_PIN(72, 161), + MX31_PIN_CSI_D7 = IOMUX_PIN(71, 162), + MX31_PIN_CSI_D6 = IOMUX_PIN(70, 163), + MX31_PIN_CSI_D5 = IOMUX_PIN(69, 164), + MX31_PIN_CSI_D4 = IOMUX_PIN(68, 165), + MX31_PIN_M_GRANT = IOMUX_PIN(0xff, 166), + MX31_PIN_M_REQUEST = IOMUX_PIN(0xff, 167), + MX31_PIN_PC_POE = IOMUX_PIN(0xff, 168), + MX31_PIN_PC_RW_B = IOMUX_PIN(0xff, 169), + MX31_PIN_IOIS16 = IOMUX_PIN(0xff, 170), + MX31_PIN_PC_RST = IOMUX_PIN(0xff, 171), + MX31_PIN_PC_BVD2 = IOMUX_PIN(0xff, 172), + MX31_PIN_PC_BVD1 = IOMUX_PIN(0xff, 173), + MX31_PIN_PC_VS2 = IOMUX_PIN(0xff, 174), + MX31_PIN_PC_VS1 = IOMUX_PIN(0xff, 175), + MX31_PIN_PC_PWRON = IOMUX_PIN(0xff, 176), + MX31_PIN_PC_READY = IOMUX_PIN(0xff, 177), + MX31_PIN_PC_WAIT_B = IOMUX_PIN(0xff, 178), + MX31_PIN_PC_CD2_B = IOMUX_PIN(0xff, 179), + MX31_PIN_PC_CD1_B = IOMUX_PIN(0xff, 180), + MX31_PIN_D0 = IOMUX_PIN(0xff, 181), + MX31_PIN_D1 = IOMUX_PIN(0xff, 182), + MX31_PIN_D2 = IOMUX_PIN(0xff, 183), + MX31_PIN_D3 = IOMUX_PIN(0xff, 184), + MX31_PIN_D4 = IOMUX_PIN(0xff, 185), + MX31_PIN_D5 = IOMUX_PIN(0xff, 186), + MX31_PIN_D6 = IOMUX_PIN(0xff, 187), + MX31_PIN_D7 = IOMUX_PIN(0xff, 188), + MX31_PIN_D8 = IOMUX_PIN(0xff, 189), + MX31_PIN_D9 = IOMUX_PIN(0xff, 190), + MX31_PIN_D10 = IOMUX_PIN(0xff, 191), + MX31_PIN_D11 = IOMUX_PIN(0xff, 192), + MX31_PIN_D12 = IOMUX_PIN(0xff, 193), + MX31_PIN_D13 = IOMUX_PIN(0xff, 194), + MX31_PIN_D14 = IOMUX_PIN(0xff, 195), + MX31_PIN_D15 = IOMUX_PIN(0xff, 196), + MX31_PIN_NFRB = IOMUX_PIN(16, 197), + MX31_PIN_NFCE_B = IOMUX_PIN(15, 198), + MX31_PIN_NFWP_B = IOMUX_PIN(14, 199), + MX31_PIN_NFCLE = IOMUX_PIN(13, 200), + MX31_PIN_NFALE = IOMUX_PIN(12, 201), + MX31_PIN_NFRE_B = IOMUX_PIN(11, 202), + MX31_PIN_NFWE_B = IOMUX_PIN(10, 203), + MX31_PIN_SDQS3 = IOMUX_PIN(0xff, 204), + MX31_PIN_SDQS2 = IOMUX_PIN(0xff, 205), + MX31_PIN_SDQS1 = IOMUX_PIN(0xff, 206), + MX31_PIN_SDQS0 = IOMUX_PIN(0xff, 207), + MX31_PIN_SDCLK_B = IOMUX_PIN(0xff, 208), + MX31_PIN_SDCLK = IOMUX_PIN(0xff, 209), + MX31_PIN_SDCKE1 = IOMUX_PIN(0xff, 210), + MX31_PIN_SDCKE0 = IOMUX_PIN(0xff, 211), + MX31_PIN_SDWE = IOMUX_PIN(0xff, 212), + MX31_PIN_CAS = IOMUX_PIN(0xff, 213), + MX31_PIN_RAS = IOMUX_PIN(0xff, 214), + MX31_PIN_RW = IOMUX_PIN(0xff, 215), + MX31_PIN_BCLK = IOMUX_PIN(0xff, 216), + MX31_PIN_LBA = IOMUX_PIN(0xff, 217), + MX31_PIN_ECB = IOMUX_PIN(0xff, 218), + MX31_PIN_CS5 = IOMUX_PIN(0xff, 219), + MX31_PIN_CS4 = IOMUX_PIN(0xff, 220), + MX31_PIN_CS3 = IOMUX_PIN(0xff, 221), + MX31_PIN_CS2 = IOMUX_PIN(0xff, 222), + MX31_PIN_CS1 = IOMUX_PIN(0xff, 223), + MX31_PIN_CS0 = IOMUX_PIN(0xff, 224), + MX31_PIN_OE = IOMUX_PIN(0xff, 225), + MX31_PIN_EB1 = IOMUX_PIN(0xff, 226), + MX31_PIN_EB0 = IOMUX_PIN(0xff, 227), + MX31_PIN_DQM3 = IOMUX_PIN(0xff, 228), + MX31_PIN_DQM2 = IOMUX_PIN(0xff, 229), + MX31_PIN_DQM1 = IOMUX_PIN(0xff, 230), + MX31_PIN_DQM0 = IOMUX_PIN(0xff, 231), + MX31_PIN_SD31 = IOMUX_PIN(0xff, 232), + MX31_PIN_SD30 = IOMUX_PIN(0xff, 233), + MX31_PIN_SD29 = IOMUX_PIN(0xff, 234), + MX31_PIN_SD28 = IOMUX_PIN(0xff, 235), + MX31_PIN_SD27 = IOMUX_PIN(0xff, 236), + MX31_PIN_SD26 = IOMUX_PIN(0xff, 237), + MX31_PIN_SD25 = IOMUX_PIN(0xff, 238), + MX31_PIN_SD24 = IOMUX_PIN(0xff, 239), + MX31_PIN_SD23 = IOMUX_PIN(0xff, 240), + MX31_PIN_SD22 = IOMUX_PIN(0xff, 241), + MX31_PIN_SD21 = IOMUX_PIN(0xff, 242), + MX31_PIN_SD20 = IOMUX_PIN(0xff, 243), + MX31_PIN_SD19 = IOMUX_PIN(0xff, 244), + MX31_PIN_SD18 = IOMUX_PIN(0xff, 245), + MX31_PIN_SD17 = IOMUX_PIN(0xff, 246), + MX31_PIN_SD16 = IOMUX_PIN(0xff, 247), + MX31_PIN_SD15 = IOMUX_PIN(0xff, 248), + MX31_PIN_SD14 = IOMUX_PIN(0xff, 249), + MX31_PIN_SD13 = IOMUX_PIN(0xff, 250), + MX31_PIN_SD12 = IOMUX_PIN(0xff, 251), + MX31_PIN_SD11 = IOMUX_PIN(0xff, 252), + MX31_PIN_SD10 = IOMUX_PIN(0xff, 253), + MX31_PIN_SD9 = IOMUX_PIN(0xff, 254), + MX31_PIN_SD8 = IOMUX_PIN(0xff, 255), + MX31_PIN_SD7 = IOMUX_PIN(0xff, 256), + MX31_PIN_SD6 = IOMUX_PIN(0xff, 257), + MX31_PIN_SD5 = IOMUX_PIN(0xff, 258), + MX31_PIN_SD4 = IOMUX_PIN(0xff, 259), + MX31_PIN_SD3 = IOMUX_PIN(0xff, 260), + MX31_PIN_SD2 = IOMUX_PIN(0xff, 261), + MX31_PIN_SD1 = IOMUX_PIN(0xff, 262), + MX31_PIN_SD0 = IOMUX_PIN(0xff, 263), + MX31_PIN_SDBA0 = IOMUX_PIN(0xff, 264), + MX31_PIN_SDBA1 = IOMUX_PIN(0xff, 265), + MX31_PIN_A25 = IOMUX_PIN(0xff, 266), + MX31_PIN_A24 = IOMUX_PIN(0xff, 267), + MX31_PIN_A23 = IOMUX_PIN(0xff, 268), + MX31_PIN_A22 = IOMUX_PIN(0xff, 269), + MX31_PIN_A21 = IOMUX_PIN(0xff, 270), + MX31_PIN_A20 = IOMUX_PIN(0xff, 271), + MX31_PIN_A19 = IOMUX_PIN(0xff, 272), + MX31_PIN_A18 = IOMUX_PIN(0xff, 273), + MX31_PIN_A17 = IOMUX_PIN(0xff, 274), + MX31_PIN_A16 = IOMUX_PIN(0xff, 275), + MX31_PIN_A14 = IOMUX_PIN(0xff, 276), + MX31_PIN_A15 = IOMUX_PIN(0xff, 277), + MX31_PIN_A13 = IOMUX_PIN(0xff, 278), + MX31_PIN_A12 = IOMUX_PIN(0xff, 279), + MX31_PIN_A11 = IOMUX_PIN(0xff, 280), + MX31_PIN_MA10 = IOMUX_PIN(0xff, 281), + MX31_PIN_A10 = IOMUX_PIN(0xff, 282), + MX31_PIN_A9 = IOMUX_PIN(0xff, 283), + MX31_PIN_A8 = IOMUX_PIN(0xff, 284), + MX31_PIN_A7 = IOMUX_PIN(0xff, 285), + MX31_PIN_A6 = IOMUX_PIN(0xff, 286), + MX31_PIN_A5 = IOMUX_PIN(0xff, 287), + MX31_PIN_A4 = IOMUX_PIN(0xff, 288), + MX31_PIN_A3 = IOMUX_PIN(0xff, 289), + MX31_PIN_A2 = IOMUX_PIN(0xff, 290), + MX31_PIN_A1 = IOMUX_PIN(0xff, 291), + MX31_PIN_A0 = IOMUX_PIN(0xff, 292), + MX31_PIN_VPG1 = IOMUX_PIN(0xff, 293), + MX31_PIN_VPG0 = IOMUX_PIN(0xff, 294), + MX31_PIN_DVFS1 = IOMUX_PIN(0xff, 295), + MX31_PIN_DVFS0 = IOMUX_PIN(0xff, 296), + MX31_PIN_VSTBY = IOMUX_PIN(0xff, 297), + MX31_PIN_POWER_FAIL = IOMUX_PIN(0xff, 298), + MX31_PIN_CKIL = IOMUX_PIN(0xff, 299), + MX31_PIN_BOOT_MODE4 = IOMUX_PIN(0xff, 300), + MX31_PIN_BOOT_MODE3 = IOMUX_PIN(0xff, 301), + MX31_PIN_BOOT_MODE2 = IOMUX_PIN(0xff, 302), + MX31_PIN_BOOT_MODE1 = IOMUX_PIN(0xff, 303), + MX31_PIN_BOOT_MODE0 = IOMUX_PIN(0xff, 304), + MX31_PIN_CLKO = IOMUX_PIN(0xff, 305), + MX31_PIN_POR_B = IOMUX_PIN(0xff, 306), + MX31_PIN_RESET_IN_B = IOMUX_PIN(0xff, 307), + MX31_PIN_CKIH = IOMUX_PIN(0xff, 308), + MX31_PIN_SIMPD0 = IOMUX_PIN(35, 309), + MX31_PIN_SRX0 = IOMUX_PIN(34, 310), + MX31_PIN_STX0 = IOMUX_PIN(33, 311), + MX31_PIN_SVEN0 = IOMUX_PIN(32, 312), + MX31_PIN_SRST0 = IOMUX_PIN(67, 313), + MX31_PIN_SCLK0 = IOMUX_PIN(66, 314), + MX31_PIN_GPIO3_1 = IOMUX_PIN(65, 315), + MX31_PIN_GPIO3_0 = IOMUX_PIN(64, 316), + MX31_PIN_GPIO1_6 = IOMUX_PIN( 6, 317), + MX31_PIN_GPIO1_5 = IOMUX_PIN( 5, 318), + MX31_PIN_GPIO1_4 = IOMUX_PIN( 4, 319), + MX31_PIN_GPIO1_3 = IOMUX_PIN( 3, 320), + MX31_PIN_GPIO1_2 = IOMUX_PIN( 2, 321), + MX31_PIN_GPIO1_1 = IOMUX_PIN( 1, 322), + MX31_PIN_GPIO1_0 = IOMUX_PIN( 0, 323), + MX31_PIN_PWMO = IOMUX_PIN( 9, 324), + MX31_PIN_WATCHDOG_RST = IOMUX_PIN(0xff, 325), + MX31_PIN_COMPARE = IOMUX_PIN( 8, 326), + MX31_PIN_CAPTURE = IOMUX_PIN( 7, 327), +}; + +/* + * Convenience values for use with mxc_iomux_mode() + * + * Format here is MX31_PIN_(pin name)__(function) + */ +#define MX31_PIN_CSPI3_MOSI__RXD3 IOMUX_MODE(MX31_PIN_CSPI3_MOSI, IOMUX_CONFIG_ALT1) +#define MX31_PIN_CSPI3_MISO__TXD3 IOMUX_MODE(MX31_PIN_CSPI3_MISO, IOMUX_CONFIG_ALT1) +#define MX31_PIN_CTS1__CTS1 IOMUX_MODE(MX31_PIN_CTS1, IOMUX_CONFIG_FUNC) +#define MX31_PIN_RTS1__RTS1 IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_FUNC) +#define MX31_PIN_TXD1__TXD1 IOMUX_MODE(MX31_PIN_TXD1, IOMUX_CONFIG_FUNC) +#define MX31_PIN_RXD1__RXD1 IOMUX_MODE(MX31_PIN_RXD1, IOMUX_CONFIG_FUNC) + +/* + * This function configures the pad value for a IOMUX pin. + */ +void mxc_iomux_set_pad(enum iomux_pins, u32); + +#endif + -- cgit v1.2.3 From d0f349fbce2905607e0473d2358f97f48866e52c Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:02:50 +0200 Subject: i.MXC family: Adding timer support This patch adds timer support for the i.MX machine family. This code can be used on the following machs: - i.MX1 (tested) - i.MX2 (i.MX21 (to be tested), i.MX27 (tested)) - i.MX3 (i.MX31 (tested)) TODO: It seems impossible to build a kernel for more than one CPU because the timer do not follow the platform device rules. So it does only work if timer 1 can be accessed on all CPUs at the same address. Signed-off-by: Juergen Beisert Signed-off-by: Sascha Hauer --- include/asm-arm/arch-mxc/common.h | 4 +- include/asm-arm/arch-mxc/mxc.h | 112 ++++--------------------- include/asm-arm/arch-mxc/mxc_timer.h | 158 +++++++++++++++++++++++++++++++++++ 3 files changed, 174 insertions(+), 100 deletions(-) create mode 100644 include/asm-arm/arch-mxc/mxc_timer.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/common.h b/include/asm-arm/arch-mxc/common.h index 8774783ed98..a6d2e24aab1 100644 --- a/include/asm-arm/arch-mxc/common.h +++ b/include/asm-arm/arch-mxc/common.h @@ -11,11 +11,9 @@ #ifndef __ASM_ARCH_MXC_COMMON_H__ #define __ASM_ARCH_MXC_COMMON_H__ -struct sys_timer; - extern void mxc_map_io(void); extern void mxc_init_irq(void); -extern struct sys_timer mxc_timer; +extern void mxc_timer_init(const char *clk_timer); extern int mxc_clocks_init(unsigned long fref); extern int mxc_register_gpios(void); diff --git a/include/asm-arm/arch-mxc/mxc.h b/include/asm-arm/arch-mxc/mxc.h index 146d3f60951..1df4e2f2492 100644 --- a/include/asm-arm/arch-mxc/mxc.h +++ b/include/asm-arm/arch-mxc/mxc.h @@ -1,11 +1,20 @@ /* * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved. - */ - -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. + * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. */ #ifndef __ASM_ARCH_MXC_H__ @@ -20,97 +29,6 @@ # define cpu_is_mx31() (0) #endif -/* - ***************************************** - * GPT Register definitions * - ***************************************** - */ -#define MXC_GPT_GPTCR IO_ADDRESS(GPT1_BASE_ADDR + 0x00) -#define MXC_GPT_GPTPR IO_ADDRESS(GPT1_BASE_ADDR + 0x04) -#define MXC_GPT_GPTSR IO_ADDRESS(GPT1_BASE_ADDR + 0x08) -#define MXC_GPT_GPTIR IO_ADDRESS(GPT1_BASE_ADDR + 0x0C) -#define MXC_GPT_GPTOCR1 IO_ADDRESS(GPT1_BASE_ADDR + 0x10) -#define MXC_GPT_GPTOCR2 IO_ADDRESS(GPT1_BASE_ADDR + 0x14) -#define MXC_GPT_GPTOCR3 IO_ADDRESS(GPT1_BASE_ADDR + 0x18) -#define MXC_GPT_GPTICR1 IO_ADDRESS(GPT1_BASE_ADDR + 0x1C) -#define MXC_GPT_GPTICR2 IO_ADDRESS(GPT1_BASE_ADDR + 0x20) -#define MXC_GPT_GPTCNT IO_ADDRESS(GPT1_BASE_ADDR + 0x24) - -/* GPT Control register bit definitions */ -#define GPTCR_FO3 (1 << 31) -#define GPTCR_FO2 (1 << 30) -#define GPTCR_FO1 (1 << 29) - -#define GPTCR_OM3_SHIFT 26 -#define GPTCR_OM3_MASK (7 << GPTCR_OM3_SHIFT) -#define GPTCR_OM3_DISCONNECTED (0 << GPTCR_OM3_SHIFT) -#define GPTCR_OM3_TOGGLE (1 << GPTCR_OM3_SHIFT) -#define GPTCR_OM3_CLEAR (2 << GPTCR_OM3_SHIFT) -#define GPTCR_OM3_SET (3 << GPTCR_OM3_SHIFT) -#define GPTCR_OM3_GENERATE_LOW (7 << GPTCR_OM3_SHIFT) - -#define GPTCR_OM2_SHIFT 23 -#define GPTCR_OM2_MASK (7 << GPTCR_OM2_SHIFT) -#define GPTCR_OM2_DISCONNECTED (0 << GPTCR_OM2_SHIFT) -#define GPTCR_OM2_TOGGLE (1 << GPTCR_OM2_SHIFT) -#define GPTCR_OM2_CLEAR (2 << GPTCR_OM2_SHIFT) -#define GPTCR_OM2_SET (3 << GPTCR_OM2_SHIFT) -#define GPTCR_OM2_GENERATE_LOW (7 << GPTCR_OM2_SHIFT) - -#define GPTCR_OM1_SHIFT 20 -#define GPTCR_OM1_MASK (7 << GPTCR_OM1_SHIFT) -#define GPTCR_OM1_DISCONNECTED (0 << GPTCR_OM1_SHIFT) -#define GPTCR_OM1_TOGGLE (1 << GPTCR_OM1_SHIFT) -#define GPTCR_OM1_CLEAR (2 << GPTCR_OM1_SHIFT) -#define GPTCR_OM1_SET (3 << GPTCR_OM1_SHIFT) -#define GPTCR_OM1_GENERATE_LOW (7 << GPTCR_OM1_SHIFT) - -#define GPTCR_IM2_SHIFT 18 -#define GPTCR_IM2_MASK (3 << GPTCR_IM2_SHIFT) -#define GPTCR_IM2_CAPTURE_DISABLE (0 << GPTCR_IM2_SHIFT) -#define GPTCR_IM2_CAPTURE_RISING (1 << GPTCR_IM2_SHIFT) -#define GPTCR_IM2_CAPTURE_FALLING (2 << GPTCR_IM2_SHIFT) -#define GPTCR_IM2_CAPTURE_BOTH (3 << GPTCR_IM2_SHIFT) - -#define GPTCR_IM1_SHIFT 16 -#define GPTCR_IM1_MASK (3 << GPTCR_IM1_SHIFT) -#define GPTCR_IM1_CAPTURE_DISABLE (0 << GPTCR_IM1_SHIFT) -#define GPTCR_IM1_CAPTURE_RISING (1 << GPTCR_IM1_SHIFT) -#define GPTCR_IM1_CAPTURE_FALLING (2 << GPTCR_IM1_SHIFT) -#define GPTCR_IM1_CAPTURE_BOTH (3 << GPTCR_IM1_SHIFT) - -#define GPTCR_SWR (1 << 15) -#define GPTCR_FRR (1 << 9) - -#define GPTCR_CLKSRC_SHIFT 6 -#define GPTCR_CLKSRC_MASK (7 << GPTCR_CLKSRC_SHIFT) -#define GPTCR_CLKSRC_NOCLOCK (0 << GPTCR_CLKSRC_SHIFT) -#define GPTCR_CLKSRC_HIGHFREQ (2 << GPTCR_CLKSRC_SHIFT) -#define GPTCR_CLKSRC_CLKIN (3 << GPTCR_CLKSRC_SHIFT) -#define GPTCR_CLKSRC_CLK32K (7 << GPTCR_CLKSRC_SHIFT) - -#define GPTCR_STOPEN (1 << 5) -#define GPTCR_DOZEN (1 << 4) -#define GPTCR_WAITEN (1 << 3) -#define GPTCR_DBGEN (1 << 2) - -#define GPTCR_ENMOD (1 << 1) -#define GPTCR_ENABLE (1 << 0) - -#define GPTSR_OF1 (1 << 0) -#define GPTSR_OF2 (1 << 1) -#define GPTSR_OF3 (1 << 2) -#define GPTSR_IF1 (1 << 3) -#define GPTSR_IF2 (1 << 4) -#define GPTSR_ROV (1 << 5) - -#define GPTIR_OF1IE GPTSR_OF1 -#define GPTIR_OF2IE GPTSR_OF2 -#define GPTIR_OF3IE GPTSR_OF3 -#define GPTIR_IF1IE GPTSR_IF1 -#define GPTIR_IF2IE GPTSR_IF2 -#define GPTIR_ROVIE GPTSR_ROV - /* ***************************************** * AVIC Registers * diff --git a/include/asm-arm/arch-mxc/mxc_timer.h b/include/asm-arm/arch-mxc/mxc_timer.h new file mode 100644 index 00000000000..6cb11f4f1a0 --- /dev/null +++ b/include/asm-arm/arch-mxc/mxc_timer.h @@ -0,0 +1,158 @@ +/* + * mxc_timer.h + * + * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) + * + * Platform independent (i.MX1, i.MX2, i.MX3) definition for timer handling. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, + * Boston, MA 02110-1301, USA. + */ + +#ifndef __PLAT_MXC_TIMER_H +#define __PLAT_MXC_TIMER_H + +#include +#include + +#ifdef CONFIG_ARCH_IMX +#define TIMER_BASE IO_ADDRESS(TIM1_BASE_ADDR) +#define TIMER_INTERRUPT TIM1_INT + +#define TCTL_VAL TCTL_CLK_PCLK1 +#define TCTL_IRQEN (1<<4) +#define TCTL_FRR (1<<8) +#define TCTL_CLK_PCLK1 (1<<1) +#define TCTL_CLK_PCLK1_4 (2<<1) +#define TCTL_CLK_TIN (3<<1) +#define TCTL_CLK_32 (4<<1) + +#define MXC_TCTL 0x00 +#define MXC_TPRER 0x04 +#define MXC_TCMP 0x08 +#define MXC_TCR 0x0c +#define MXC_TCN 0x10 +#define MXC_TSTAT 0x14 +#define TSTAT_CAPT (1<<1) +#define TSTAT_COMP (1<<0) + +static inline void gpt_irq_disable(void) +{ + unsigned int tmp; + + tmp = __raw_readl(TIMER_BASE + MXC_TCTL); + __raw_writel(tmp & ~TCTL_IRQEN, TIMER_BASE + MXC_TCTL); +} + +static inline void gpt_irq_enable(void) +{ + __raw_writel(__raw_readl(TIMER_BASE + MXC_TCTL) | TCTL_IRQEN, + TIMER_BASE + MXC_TCTL); +} + +static void gpt_irq_acknowledge(void) +{ + __raw_writel(0, TIMER_BASE + MXC_TSTAT); +} +#endif /* CONFIG_ARCH_IMX */ + +#ifdef CONFIG_ARCH_MX2 +#define TIMER_BASE IO_ADDRESS(GPT1_BASE_ADDR) +#define TIMER_INTERRUPT MXC_INT_GPT1 + +#define MXC_TCTL 0x00 +#define TCTL_VAL TCTL_CLK_PCLK1 +#define TCTL_CLK_PCLK1 (1<<1) +#define TCTL_CLK_PCLK1_4 (2<<1) +#define TCTL_IRQEN (1<<4) +#define TCTL_FRR (1<<8) +#define MXC_TPRER 0x04 +#define MXC_TCMP 0x08 +#define MXC_TCR 0x0c +#define MXC_TCN 0x10 +#define MXC_TSTAT 0x14 +#define TSTAT_CAPT (1<<1) +#define TSTAT_COMP (1<<0) + +static inline void gpt_irq_disable(void) +{ + unsigned int tmp; + + tmp = __raw_readl(TIMER_BASE + MXC_TCTL); + __raw_writel(tmp & ~TCTL_IRQEN, TIMER_BASE + MXC_TCTL); +} + +static inline void gpt_irq_enable(void) +{ + __raw_writel(__raw_readl(TIMER_BASE + MXC_TCTL) | TCTL_IRQEN, + TIMER_BASE + MXC_TCTL); +} + +static void gpt_irq_acknowledge(void) +{ + __raw_writel(TSTAT_CAPT | TSTAT_COMP, TIMER_BASE + MXC_TSTAT); +} +#endif /* CONFIG_ARCH_MX2 */ + +#ifdef CONFIG_ARCH_MX3 +#define TIMER_BASE IO_ADDRESS(GPT1_BASE_ADDR) +#define TIMER_INTERRUPT MXC_INT_GPT + +#define MXC_TCTL 0x00 +#define TCTL_VAL (TCTL_CLK_IPG | TCTL_WAITEN) +#define TCTL_CLK_IPG (1<<6) +#define TCTL_FRR (1<<9) +#define TCTL_WAITEN (1<<3) + +#define MXC_TPRER 0x04 +#define MXC_TSTAT 0x08 +#define TSTAT_OF1 (1<<0) +#define TSTAT_OF2 (1<<1) +#define TSTAT_OF3 (1<<2) +#define TSTAT_IF1 (1<<3) +#define TSTAT_IF2 (1<<4) +#define TSTAT_ROV (1<<5) +#define MXC_IR 0x0c +#define MXC_TCMP 0x10 +#define MXC_TCMP2 0x14 +#define MXC_TCMP3 0x18 +#define MXC_TCR 0x1c +#define MXC_TCN 0x24 + +static inline void gpt_irq_disable(void) +{ + __raw_writel(0, TIMER_BASE + MXC_IR); +} + +static inline void gpt_irq_enable(void) +{ + __raw_writel(1<<0, TIMER_BASE + MXC_IR); +} + +static inline void gpt_irq_acknowledge(void) +{ + __raw_writel(TSTAT_OF1, TIMER_BASE + MXC_TSTAT); +} +#endif /* CONFIG_ARCH_MX3 */ + +#define TCTL_SWR (1<<15) +#define TCTL_CC (1<<10) +#define TCTL_OM (1<<9) +#define TCTL_CAP_RIS (1<<6) +#define TCTL_CAP_FAL (2<<6) +#define TCTL_CAP_RIS_FAL (3<<6) +#define TCTL_CAP_ENA (1<<5) +#define TCTL_TEN (1<<0) + +#endif -- cgit v1.2.3 From 4bc256501a159abc7e9fee43f63c68894f6a11d8 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Sat, 5 Jul 2008 10:02:51 +0200 Subject: MXC: add debug-macro.S for mxc This patch adds debug-macro.S for arch-mxc Disadvantage: Due to the board specific UART definition, these macros (and compile time) will fail for multi board kernels. Signed-off-by: Sascha Hauer --- include/asm-arm/arch-mxc/board-mx31ads.h | 5 +++++ include/asm-arm/arch-mxc/debug-macro.S | 38 ++++++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+) create mode 100644 include/asm-arm/arch-mxc/debug-macro.S (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/board-mx31ads.h b/include/asm-arm/arch-mxc/board-mx31ads.h index 8590127760a..1bc6fb0f9a8 100644 --- a/include/asm-arm/arch-mxc/board-mx31ads.h +++ b/include/asm-arm/arch-mxc/board-mx31ads.h @@ -109,4 +109,9 @@ #define MXC_MAX_EXP_IO_LINES 16 +/* mandatory for CONFIG_LL_DEBUG */ + +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) + #endif /* __ASM_ARCH_MXC_BOARD_MX31ADS_H__ */ diff --git a/include/asm-arm/arch-mxc/debug-macro.S b/include/asm-arm/arch-mxc/debug-macro.S new file mode 100644 index 00000000000..34befbb2ea4 --- /dev/null +++ b/include/asm-arm/arch-mxc/debug-macro.S @@ -0,0 +1,38 @@ +/* linux/include/asm-arm/arch-imx/debug-macro.S + * + * Debugging macro include header + * + * Copyright (C) 1994-1999 Russell King + * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include + +#ifdef CONFIG_MACH_MX31ADS +#include +#endif + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + ldreq \rx, =MXC_LL_UART_PADDR @ physical + ldrne \rx, =MXC_LL_UART_VADDR @ virtual + .endm + + .macro senduart,rd,rx + str \rd, [\rx, #0x40] @ TXDATA + .endm + + .macro waituart,rd,rx + .endm + + .macro busyuart,rd,rx +1002: ldr \rd, [\rx, #0x98] @ SR2 + tst \rd, #1 << 3 @ TXDC + beq 1002b @ wait until transmit done + .endm -- cgit v1.2.3 From ce8ffef0bfd6e55d5da3923d8e9af27c3b5c4eff Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Sat, 5 Jul 2008 10:02:52 +0200 Subject: MX31: add basic pcm037 board support This patch adds basic board support for phytecs pmc037 board. Signed-off-by: Sascha Hauer --- include/asm-arm/arch-mxc/board-pcm037.h | 27 +++++++++++++++++++++++++++ include/asm-arm/arch-mxc/debug-macro.S | 3 +++ 2 files changed, 30 insertions(+) create mode 100644 include/asm-arm/arch-mxc/board-pcm037.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/board-pcm037.h b/include/asm-arm/arch-mxc/board-pcm037.h new file mode 100644 index 00000000000..82232ba3c8f --- /dev/null +++ b/include/asm-arm/arch-mxc/board-pcm037.h @@ -0,0 +1,27 @@ +/* + * Copyright (C) 2008 Sascha Hauer, Pengutronix + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __ASM_ARCH_MXC_BOARD_PCM037_H__ +#define __ASM_ARCH_MXC_BOARD_PCM037_H__ + +/* mandatory for CONFIG_LL_DEBUG */ + +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) + +#endif /* __ASM_ARCH_MXC_BOARD_PCM037_H__ */ diff --git a/include/asm-arm/arch-mxc/debug-macro.S b/include/asm-arm/arch-mxc/debug-macro.S index 34befbb2ea4..81caa0aacfe 100644 --- a/include/asm-arm/arch-mxc/debug-macro.S +++ b/include/asm-arm/arch-mxc/debug-macro.S @@ -15,6 +15,9 @@ #ifdef CONFIG_MACH_MX31ADS #include +#endif +#ifdef CONFIG_MACH_PCM037 +#include #endif .macro addruart,rx -- cgit v1.2.3 From 9a4cd7a5c836e189a1712c9ffd2d76b2302ce212 Mon Sep 17 00:00:00 2001 From: Daniel Mack Date: Sat, 5 Jul 2008 10:02:53 +0200 Subject: MX3: Add basic support for LogicPD i.MX31 LiteKit MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This patch adds basic support for i.MX31 LiteKit by LogicPD. With printascii() in kernel/printk.c, it boots right into the rootfs-panic. Note: This is a modified version of Daniel's patch to fit into this patch stack. > On 09.06.2008, at 17:26, Russell King - ARM Linux wrote: > > > I would much prefer it if board specific includes were included by the > > code which needs them rather than in asm/arch/hardware.h.  With the > > device model, drivers shouldn't need to include any board specific > > includes - only the board specific C file should need it. > > The new version of this patch (#5102) has been uploaded to the patch > tracker this morning. Signed-off-by: Daniel Mack -- arch/arm/configs/mx31litekit_defconfig | 1100 ++++++++++++++++++++++++++++++ arch/arm/mach-mx3/Kconfig | 7 arch/arm/mach-mx3/Makefile | 1 arch/arm/mach-mx3/mx31lite.c | 96 ++ include/asm-arm/arch-mxc/board-mx31lite.h | 38 + include/asm-arm/arch-mxc/debug-macro.S | 3 6 files changed, 1245 insertions(+) --- include/asm-arm/arch-mxc/board-mx31lite.h | 38 +++++++++++++++++++++++++++++++ include/asm-arm/arch-mxc/debug-macro.S | 3 +++ 2 files changed, 41 insertions(+) create mode 100644 include/asm-arm/arch-mxc/board-mx31lite.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/board-mx31lite.h b/include/asm-arm/arch-mxc/board-mx31lite.h new file mode 100644 index 00000000000..e4e5cf5ad7d --- /dev/null +++ b/include/asm-arm/arch-mxc/board-mx31lite.h @@ -0,0 +1,38 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved. + */ + +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_MXC_BOARD_MX31LITE_H__ +#define __ASM_ARCH_MXC_BOARD_MX31LITE_H__ + +#define MXC_MAX_EXP_IO_LINES 16 + + +/* + * Memory Size parameters + */ + +/* + * Size of SDRAM memory + */ +#define SDRAM_MEM_SIZE SZ_128M +/* + * Size of MBX buffer memory + */ +#define MXC_MBX_MEM_SIZE SZ_16M +/* + * Size of memory available to kernel + */ +#define MEM_SIZE (SDRAM_MEM_SIZE - MXC_MBX_MEM_SIZE) + +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) + +#endif /* __ASM_ARCH_MXC_BOARD_MX31ADS_H__ */ + diff --git a/include/asm-arm/arch-mxc/debug-macro.S b/include/asm-arm/arch-mxc/debug-macro.S index 81caa0aacfe..5add48b6665 100644 --- a/include/asm-arm/arch-mxc/debug-macro.S +++ b/include/asm-arm/arch-mxc/debug-macro.S @@ -18,6 +18,9 @@ #endif #ifdef CONFIG_MACH_PCM037 #include +#endif +#ifdef CONFIG_MACH_MX31LITE +#include #endif .macro addruart,rx -- cgit v1.2.3 From 259bcaae9a2f28d7e3303b202b64a1fb0a9ab9e4 Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:02:54 +0200 Subject: MXC arch: Simplify architecture's irq sources Simplify architecture's irq headers and sources, to share these files between MXC3 and MXC2. Signed-off-by: Juergen Beisert --- include/asm-arm/arch-mxc/irqs.h | 13 ------------- include/asm-arm/arch-mxc/mx31.h | 2 ++ include/asm-arm/arch-mxc/mxc.h | 38 -------------------------------------- 3 files changed, 2 insertions(+), 51 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/irqs.h b/include/asm-arm/arch-mxc/irqs.h index b2c5205e196..f416130718c 100644 --- a/include/asm-arm/arch-mxc/irqs.h +++ b/include/asm-arm/arch-mxc/irqs.h @@ -13,17 +13,4 @@ #include -#define MXC_IRQ_TO_EXPIO(irq) ((irq) - MXC_EXP_IO_BASE) - -#define MXC_IRQ_TO_GPIO(irq) ((irq) - MXC_GPIO_INT_BASE) -#define MXC_GPIO_TO_IRQ(x) (MXC_GPIO_INT_BASE + x) - -/* Number of normal interrupts */ -#define NR_IRQS (MXC_MAX_INT_LINES + \ - MXC_MAX_GPIO_LINES + \ - MXC_MAX_VIRTUAL_INTS) - -/* Number of fast interrupts */ -#define NR_FIQS MXC_MAX_INTS - #endif /* __ASM_ARCH_MXC_IRQS_H__ */ diff --git a/include/asm-arm/arch-mxc/mx31.h b/include/asm-arm/arch-mxc/mx31.h index 98e6a4cd1ea..a7373e4a56c 100644 --- a/include/asm-arm/arch-mxc/mx31.h +++ b/include/asm-arm/arch-mxc/mx31.h @@ -320,6 +320,8 @@ #define MXC_MAX_GPIO_LINES (GPIO_NUM_PIN * GPIO_PORT_NUM) #define MXC_MAX_VIRTUAL_INTS 16 +#define NR_IRQS (MXC_MAX_INT_LINES + MXC_MAX_GPIO_LINES + MXC_MAX_VIRTUAL_INTS) + /*! * Number of GPIO port as defined in the IC Spec */ diff --git a/include/asm-arm/arch-mxc/mxc.h b/include/asm-arm/arch-mxc/mxc.h index 1df4e2f2492..3e1c4ded18e 100644 --- a/include/asm-arm/arch-mxc/mxc.h +++ b/include/asm-arm/arch-mxc/mxc.h @@ -29,42 +29,4 @@ # define cpu_is_mx31() (0) #endif -/* - ***************************************** - * AVIC Registers * - ***************************************** - */ -#define AVIC_BASE IO_ADDRESS(AVIC_BASE_ADDR) -#define AVIC_INTCNTL (AVIC_BASE + 0x00) /* int control reg */ -#define AVIC_NIMASK (AVIC_BASE + 0x04) /* int mask reg */ -#define AVIC_INTENNUM (AVIC_BASE + 0x08) /* int enable number reg */ -#define AVIC_INTDISNUM (AVIC_BASE + 0x0C) /* int disable number reg */ -#define AVIC_INTENABLEH (AVIC_BASE + 0x10) /* int enable reg high */ -#define AVIC_INTENABLEL (AVIC_BASE + 0x14) /* int enable reg low */ -#define AVIC_INTTYPEH (AVIC_BASE + 0x18) /* int type reg high */ -#define AVIC_INTTYPEL (AVIC_BASE + 0x1C) /* int type reg low */ -#define AVIC_NIPRIORITY7 (AVIC_BASE + 0x20) /* norm int priority lvl7 */ -#define AVIC_NIPRIORITY6 (AVIC_BASE + 0x24) /* norm int priority lvl6 */ -#define AVIC_NIPRIORITY5 (AVIC_BASE + 0x28) /* norm int priority lvl5 */ -#define AVIC_NIPRIORITY4 (AVIC_BASE + 0x2C) /* norm int priority lvl4 */ -#define AVIC_NIPRIORITY3 (AVIC_BASE + 0x30) /* norm int priority lvl3 */ -#define AVIC_NIPRIORITY2 (AVIC_BASE + 0x34) /* norm int priority lvl2 */ -#define AVIC_NIPRIORITY1 (AVIC_BASE + 0x38) /* norm int priority lvl1 */ -#define AVIC_NIPRIORITY0 (AVIC_BASE + 0x3C) /* norm int priority lvl0 */ -#define AVIC_NIVECSR (AVIC_BASE + 0x40) /* norm int vector/status */ -#define AVIC_FIVECSR (AVIC_BASE + 0x44) /* fast int vector/status */ -#define AVIC_INTSRCH (AVIC_BASE + 0x48) /* int source reg high */ -#define AVIC_INTSRCL (AVIC_BASE + 0x4C) /* int source reg low */ -#define AVIC_INTFRCH (AVIC_BASE + 0x50) /* int force reg high */ -#define AVIC_INTFRCL (AVIC_BASE + 0x54) /* int force reg low */ -#define AVIC_NIPNDH (AVIC_BASE + 0x58) /* norm int pending high */ -#define AVIC_NIPNDL (AVIC_BASE + 0x5C) /* norm int pending low */ -#define AVIC_FIPNDH (AVIC_BASE + 0x60) /* fast int pending high */ -#define AVIC_FIPNDL (AVIC_BASE + 0x64) /* fast int pending low */ - -#define SYSTEM_PREV_REG IO_ADDRESS(IIM_BASE_ADDR + 0x20) -#define SYSTEM_SREV_REG IO_ADDRESS(IIM_BASE_ADDR + 0x24) -#define IIM_PROD_REV_SH 3 -#define IIM_PROD_REV_LEN 5 - #endif /* __ASM_ARCH_MXC_H__ */ -- cgit v1.2.3 From aa10abd381b9493a88f6b9e111adc79e33d548fa Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:02:55 +0200 Subject: i.MX2 family: Add GPIO multiplexing support This patch adds GPIO multiplexing support for the imx1/mxc2 family of procesors. Signed-off-by: Juergen Beisert --- include/asm-arm/arch-mxc/iomux-mx1-mx2.h | 372 +++++++++++++++++++++++++++++++ 1 file changed, 372 insertions(+) create mode 100644 include/asm-arm/arch-mxc/iomux-mx1-mx2.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/iomux-mx1-mx2.h b/include/asm-arm/arch-mxc/iomux-mx1-mx2.h new file mode 100644 index 00000000000..076d37b38eb --- /dev/null +++ b/include/asm-arm/arch-mxc/iomux-mx1-mx2.h @@ -0,0 +1,372 @@ +/* + * Copyright (C) 2008 by Sascha Hauer + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef _MXC_GPIO_MX1_MX2_H +#define _MXC_GPIO_MX1_MX2_H + +#include + +#define MXC_GPIO_ALLOC_MODE_NORMAL 0 +#define MXC_GPIO_ALLOC_MODE_NO_ALLOC 1 +#define MXC_GPIO_ALLOC_MODE_TRY_ALLOC 2 +#define MXC_GPIO_ALLOC_MODE_ALLOC_ONLY 4 +#define MXC_GPIO_ALLOC_MODE_RELEASE 8 + +/* + * GPIO Module and I/O Multiplexer + * x = 0..3 for reg_A, reg_B, reg_C, reg_D + */ +#define VA_GPIO_BASE IO_ADDRESS(GPIO_BASE_ADDR) +#define MXC_DDIR(x) (0x00 + ((x) << 8)) +#define MXC_OCR1(x) (0x04 + ((x) << 8)) +#define MXC_OCR2(x) (0x08 + ((x) << 8)) +#define MXC_ICONFA1(x) (0x0c + ((x) << 8)) +#define MXC_ICONFA2(x) (0x10 + ((x) << 8)) +#define MXC_ICONFB1(x) (0x14 + ((x) << 8)) +#define MXC_ICONFB2(x) (0x18 + ((x) << 8)) +#define MXC_DR(x) (0x1c + ((x) << 8)) +#define MXC_GIUS(x) (0x20 + ((x) << 8)) +#define MXC_SSR(x) (0x24 + ((x) << 8)) +#define MXC_ICR1(x) (0x28 + ((x) << 8)) +#define MXC_ICR2(x) (0x2c + ((x) << 8)) +#define MXC_IMR(x) (0x30 + ((x) << 8)) +#define MXC_ISR(x) (0x34 + ((x) << 8)) +#define MXC_GPR(x) (0x38 + ((x) << 8)) +#define MXC_SWR(x) (0x3c + ((x) << 8)) +#define MXC_PUEN(x) (0x40 + ((x) << 8)) + +#ifdef CONFIG_ARCH_MX1 +# define GPIO_PORT_MAX 3 +#endif +#ifdef CONFIG_ARCH_MX2 +# define GPIO_PORT_MAX 5 +#endif + +#ifndef GPIO_PORT_MAX +# error "GPIO config port count unknown!" +#endif + +#define GPIO_PIN_MASK 0x1f + +#define GPIO_PORT_SHIFT 5 +#define GPIO_PORT_MASK (0x7 << GPIO_PORT_SHIFT) + +#define GPIO_PORTA (0 << GPIO_PORT_SHIFT) +#define GPIO_PORTB (1 << GPIO_PORT_SHIFT) +#define GPIO_PORTC (2 << GPIO_PORT_SHIFT) +#define GPIO_PORTD (3 << GPIO_PORT_SHIFT) +#define GPIO_PORTE (4 << GPIO_PORT_SHIFT) +#define GPIO_PORTF (5 << GPIO_PORT_SHIFT) + +#define GPIO_OUT (1 << 8) +#define GPIO_IN (0 << 8) +#define GPIO_PUEN (1 << 9) + +#define GPIO_PF (1 << 10) +#define GPIO_AF (1 << 11) + +#define GPIO_OCR_SHIFT 12 +#define GPIO_OCR_MASK (3 << GPIO_OCR_SHIFT) +#define GPIO_AIN (0 << GPIO_OCR_SHIFT) +#define GPIO_BIN (1 << GPIO_OCR_SHIFT) +#define GPIO_CIN (2 << GPIO_OCR_SHIFT) +#define GPIO_GPIO (3 << GPIO_OCR_SHIFT) + +#define GPIO_AOUT_SHIFT 14 +#define GPIO_AOUT_MASK (3 << GPIO_AOUT_SHIFT) +#define GPIO_AOUT (0 << GPIO_AOUT_SHIFT) +#define GPIO_AOUT_ISR (1 << GPIO_AOUT_SHIFT) +#define GPIO_AOUT_0 (2 << GPIO_AOUT_SHIFT) +#define GPIO_AOUT_1 (3 << GPIO_AOUT_SHIFT) + +#define GPIO_BOUT_SHIFT 16 +#define GPIO_BOUT_MASK (3 << GPIO_BOUT_SHIFT) +#define GPIO_BOUT (0 << GPIO_BOUT_SHIFT) +#define GPIO_BOUT_ISR (1 << GPIO_BOUT_SHIFT) +#define GPIO_BOUT_0 (2 << GPIO_BOUT_SHIFT) +#define GPIO_BOUT_1 (3 << GPIO_BOUT_SHIFT) + +extern void mxc_gpio_mode(int gpio_mode); +extern int mxc_gpio_setup_multiple_pins(const int *pin_list, unsigned count, + int alloc_mode, const char *label); + +/*-------------------------------------------------------------------------*/ + +/* assignements for GPIO alternate/primary functions */ + +/* FIXME: This list is not completed. The correct directions are + * missing on some (many) pins + */ +#ifdef CONFIG_ARCH_MX1 +#define PA0_AIN_SPI2_CLK (GPIO_GIUS | GPIO_PORTA | GPIO_OUT | 0) +#define PA0_AF_ETMTRACESYNC (GPIO_PORTA | GPIO_AF | 0) +#define PA1_AOUT_SPI2_RXD (GPIO_GIUS | GPIO_PORTA | GPIO_IN | 1) +#define PA1_PF_TIN (GPIO_PORTA | GPIO_PF | 1) +#define PA2_PF_PWM0 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 2) +#define PA3_PF_CSI_MCLK (GPIO_PORTA | GPIO_PF | 3) +#define PA4_PF_CSI_D0 (GPIO_PORTA | GPIO_PF | 4) +#define PA5_PF_CSI_D1 (GPIO_PORTA | GPIO_PF | 5) +#define PA6_PF_CSI_D2 (GPIO_PORTA | GPIO_PF | 6) +#define PA7_PF_CSI_D3 (GPIO_PORTA | GPIO_PF | 7) +#define PA8_PF_CSI_D4 (GPIO_PORTA | GPIO_PF | 8) +#define PA9_PF_CSI_D5 (GPIO_PORTA | GPIO_PF | 9) +#define PA10_PF_CSI_D6 (GPIO_PORTA | GPIO_PF | 10) +#define PA11_PF_CSI_D7 (GPIO_PORTA | GPIO_PF | 11) +#define PA12_PF_CSI_VSYNC (GPIO_PORTA | GPIO_PF | 12) +#define PA13_PF_CSI_HSYNC (GPIO_PORTA | GPIO_PF | 13) +#define PA14_PF_CSI_PIXCLK (GPIO_PORTA | GPIO_PF | 14) +#define PA15_PF_I2C_SDA (GPIO_PORTA | GPIO_OUT | GPIO_PF | 15) +#define PA16_PF_I2C_SCL (GPIO_PORTA | GPIO_OUT | GPIO_PF | 16) +#define PA17_AF_ETMTRACEPKT4 (GPIO_PORTA | GPIO_AF | 17) +#define PA17_AIN_SPI2_SS (GPIO_GIUS | GPIO_PORTA | GPIO_OUT | 17) +#define PA18_AF_ETMTRACEPKT5 (GPIO_PORTA | GPIO_AF | 18) +#define PA19_AF_ETMTRACEPKT6 (GPIO_PORTA | GPIO_AF | 19) +#define PA20_AF_ETMTRACEPKT7 (GPIO_PORTA | GPIO_AF | 20) +#define PA21_PF_A0 (GPIO_PORTA | GPIO_PF | 21) +#define PA22_PF_CS4 (GPIO_PORTA | GPIO_PF | 22) +#define PA23_PF_CS5 (GPIO_PORTA | GPIO_PF | 23) +#define PA24_PF_A16 (GPIO_PORTA | GPIO_PF | 24) +#define PA24_AF_ETMTRACEPKT0 (GPIO_PORTA | GPIO_AF | 24) +#define PA25_PF_A17 (GPIO_PORTA | GPIO_PF | 25) +#define PA25_AF_ETMTRACEPKT1 (GPIO_PORTA | GPIO_AF | 25) +#define PA26_PF_A18 (GPIO_PORTA | GPIO_PF | 26) +#define PA26_AF_ETMTRACEPKT2 (GPIO_PORTA | GPIO_AF | 26) +#define PA27_PF_A19 (GPIO_PORTA | GPIO_PF | 27) +#define PA27_AF_ETMTRACEPKT3 (GPIO_PORTA | GPIO_AF | 27) +#define PA28_PF_A20 (GPIO_PORTA | GPIO_PF | 28) +#define PA28_AF_ETMPIPESTAT0 (GPIO_PORTA | GPIO_AF | 28) +#define PA29_PF_A21 (GPIO_PORTA | GPIO_PF | 29) +#define PA29_AF_ETMPIPESTAT1 (GPIO_PORTA | GPIO_AF | 29) +#define PA30_PF_A22 (GPIO_PORTA | GPIO_PF | 30) +#define PA30_AF_ETMPIPESTAT2 (GPIO_PORTA | GPIO_AF | 30) +#define PA31_PF_A23 (GPIO_PORTA | GPIO_PF | 31) +#define PA31_AF_ETMTRACECLK (GPIO_PORTA | GPIO_AF | 31) +#define PB8_PF_SD_DAT0 (GPIO_PORTB | GPIO_PF | GPIO_PUEN | 8) +#define PB8_AF_MS_PIO (GPIO_PORTB | GPIO_AF | 8) +#define PB9_PF_SD_DAT1 (GPIO_PORTB | GPIO_PF | GPIO_PUEN | 9) +#define PB9_AF_MS_PI1 (GPIO_PORTB | GPIO_AF | 9) +#define PB10_PF_SD_DAT2 (GPIO_PORTB | GPIO_PF | GPIO_PUEN | 10) +#define PB10_AF_MS_SCLKI (GPIO_PORTB | GPIO_AF | 10) +#define PB11_PF_SD_DAT3 (GPIO_PORTB | GPIO_PF | 11) +#define PB11_AF_MS_SDIO (GPIO_PORTB | GPIO_AF | 11) +#define PB12_PF_SD_CLK (GPIO_PORTB | GPIO_PF | 12) +#define PB12_AF_MS_SCLK0 (GPIO_PORTB | GPIO_AF | 12) +#define PB13_PF_SD_CMD (GPIO_PORTB | GPIO_PF | GPIO_PUEN | 13) +#define PB13_AF_MS_BS (GPIO_PORTB | GPIO_AF | 13) +#define PB14_AF_SSI_RXFS (GPIO_PORTB | GPIO_AF | 14) +#define PB15_AF_SSI_RXCLK (GPIO_PORTB | GPIO_AF | 15) +#define PB16_AF_SSI_RXDAT (GPIO_PORTB | GPIO_IN | GPIO_AF | 16) +#define PB17_AF_SSI_TXDAT (GPIO_PORTB | GPIO_OUT | GPIO_AF | 17) +#define PB18_AF_SSI_TXFS (GPIO_PORTB | GPIO_AF | 18) +#define PB19_AF_SSI_TXCLK (GPIO_PORTB | GPIO_AF | 19) +#define PB20_PF_USBD_AFE (GPIO_PORTB | GPIO_PF | 20) +#define PB21_PF_USBD_OE (GPIO_PORTB | GPIO_PF | 21) +#define PB22_PFUSBD_RCV (GPIO_PORTB | GPIO_PF | 22) +#define PB23_PF_USBD_SUSPND (GPIO_PORTB | GPIO_PF | 23) +#define PB24_PF_USBD_VP (GPIO_PORTB | GPIO_PF | 24) +#define PB25_PF_USBD_VM (GPIO_PORTB | GPIO_PF | 25) +#define PB26_PF_USBD_VPO (GPIO_PORTB | GPIO_PF | 26) +#define PB27_PF_USBD_VMO (GPIO_PORTB | GPIO_PF | 27) +#define PB28_PF_UART2_CTS (GPIO_PORTB | GPIO_OUT | GPIO_PF | 28) +#define PB29_PF_UART2_RTS (GPIO_PORTB | GPIO_IN | GPIO_PF | 29) +#define PB30_PF_UART2_TXD (GPIO_PORTB | GPIO_OUT | GPIO_PF | 30) +#define PB31_PF_UART2_RXD (GPIO_PORTB | GPIO_IN | GPIO_PF | 31) +#define PC3_PF_SSI_RXFS (GPIO_PORTC | GPIO_PF | 3) +#define PC4_PF_SSI_RXCLK (GPIO_PORTC | GPIO_PF | 4) +#define PC5_PF_SSI_RXDAT (GPIO_PORTC | GPIO_IN | GPIO_PF | 5) +#define PC6_PF_SSI_TXDAT (GPIO_PORTC | GPIO_OUT | GPIO_PF | 6) +#define PC7_PF_SSI_TXFS (GPIO_PORTC | GPIO_PF | 7) +#define PC8_PF_SSI_TXCLK (GPIO_PORTC | GPIO_PF | 8) +#define PC9_PF_UART1_CTS (GPIO_PORTC | GPIO_OUT | GPIO_PF | 9) +#define PC10_PF_UART1_RTS (GPIO_PORTC | GPIO_IN | GPIO_PF | 10) +#define PC11_PF_UART1_TXD (GPIO_PORTC | GPIO_OUT | GPIO_PF | 11) +#define PC12_PF_UART1_RXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 12) +#define PC13_PF_SPI1_SPI_RDY (GPIO_PORTC | GPIO_PF | 13) +#define PC14_PF_SPI1_SCLK (GPIO_PORTC | GPIO_PF | 14) +#define PC15_PF_SPI1_SS (GPIO_PORTC | GPIO_PF | 15) +#define PC16_PF_SPI1_MISO (GPIO_PORTC | GPIO_PF | 16) +#define PC17_PF_SPI1_MOSI (GPIO_PORTC | GPIO_PF | 17) +#define PC24_BIN_UART3_RI (GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 24) +#define PC25_BIN_UART3_DSR (GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 25) +#define PC26_AOUT_UART3_DTR (GPIO_GIUS | GPIO_PORTC | GPIO_IN | 26) +#define PC27_BIN_UART3_DCD (GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 27) +#define PC28_BIN_UART3_CTS (GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 28) +#define PC29_AOUT_UART3_RTS (GPIO_GIUS | GPIO_PORTC | GPIO_IN | 29) +#define PC30_BIN_UART3_TX (GPIO_GIUS | GPIO_PORTC | GPIO_BIN | 30) +#define PC31_AOUT_UART3_RX (GPIO_GIUS | GPIO_PORTC | GPIO_IN | 31) +#define PD6_PF_LSCLK (GPIO_PORTD | GPIO_OUT | GPIO_PF | 6) +#define PD7_PF_REV (GPIO_PORTD | GPIO_PF | 7) +#define PD7_AF_UART2_DTR (GPIO_GIUS | GPIO_PORTD | GPIO_IN | GPIO_AF | 7) +#define PD7_AIN_SPI2_SCLK (GPIO_GIUS | GPIO_PORTD | GPIO_AIN | 7) +#define PD8_PF_CLS (GPIO_PORTD | GPIO_PF | 8) +#define PD8_AF_UART2_DCD (GPIO_PORTD | GPIO_OUT | GPIO_AF | 8) +#define PD8_AIN_SPI2_SS (GPIO_GIUS | GPIO_PORTD | GPIO_AIN | 8) +#define PD9_PF_PS (GPIO_PORTD | GPIO_PF | 9) +#define PD9_AF_UART2_RI (GPIO_PORTD | GPIO_OUT | GPIO_AF | 9) +#define PD9_AOUT_SPI2_RXD (GPIO_GIUS | GPIO_PORTD | GPIO_IN | 9) +#define PD10_PF_SPL_SPR (GPIO_PORTD | GPIO_OUT | GPIO_PF | 10) +#define PD10_AF_UART2_DSR (GPIO_PORTD | GPIO_OUT | GPIO_AF | 10) +#define PD10_AIN_SPI2_TXD (GPIO_GIUS | GPIO_PORTD | GPIO_OUT | 10) +#define PD11_PF_CONTRAST (GPIO_PORTD | GPIO_OUT | GPIO_PF | 11) +#define PD12_PF_ACD_OE (GPIO_PORTD | GPIO_OUT | GPIO_PF | 12) +#define PD13_PF_LP_HSYNC (GPIO_PORTD | GPIO_OUT | GPIO_PF | 13) +#define PD14_PF_FLM_VSYNC (GPIO_PORTD | GPIO_OUT | GPIO_PF | 14) +#define PD15_PF_LD0 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 15) +#define PD16_PF_LD1 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 16) +#define PD17_PF_LD2 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 17) +#define PD18_PF_LD3 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 18) +#define PD19_PF_LD4 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 19) +#define PD20_PF_LD5 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 20) +#define PD21_PF_LD6 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 21) +#define PD22_PF_LD7 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 22) +#define PD23_PF_LD8 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 23) +#define PD24_PF_LD9 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 24) +#define PD25_PF_LD10 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 25) +#define PD26_PF_LD11 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 26) +#define PD27_PF_LD12 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 27) +#define PD28_PF_LD13 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 28) +#define PD29_PF_LD14 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 29) +#define PD30_PF_LD15 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 30) +#define PD31_PF_TMR2OUT (GPIO_PORTD | GPIO_PF | 31) +#define PD31_BIN_SPI2_TXD (GPIO_GIUS | GPIO_PORTD | GPIO_BIN | 31) +#endif + +#ifdef CONFIG_ARCH_MX2 +#define PA5_PF_LSCLK (GPIO_PORTA | GPIO_OUT | GPIO_PF | 5) +#define PA6_PF_LD0 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 6) +#define PA7_PF_LD1 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 7) +#define PA8_PF_LD2 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 8) +#define PA9_PF_LD3 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 9) +#define PA10_PF_LD4 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 10) +#define PA11_PF_LD5 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 11) +#define PA12_PF_LD6 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 12) +#define PA13_PF_LD7 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 13) +#define PA14_PF_LD8 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 14) +#define PA15_PF_LD9 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 15) +#define PA16_PF_LD10 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 16) +#define PA17_PF_LD11 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 17) +#define PA18_PF_LD12 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 18) +#define PA19_PF_LD13 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 19) +#define PA20_PF_LD14 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 20) +#define PA21_PF_LD15 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 21) +#define PA22_PF_LD16 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 22) +#define PA23_PF_LD17 (GPIO_PORTA | GPIO_OUT | GPIO_PF | 23) +#define PA24_PF_REV (GPIO_PORTA | GPIO_OUT | GPIO_PF | 24) +#define PA25_PF_CLS (GPIO_PORTA | GPIO_OUT | GPIO_PF | 25) +#define PA26_PF_PS (GPIO_PORTA | GPIO_OUT | GPIO_PF | 26) +#define PA27_PF_SPL_SPR (GPIO_PORTA | GPIO_OUT | GPIO_PF | 27) +#define PA28_PF_HSYNC (GPIO_PORTA | GPIO_OUT | GPIO_PF | 28) +#define PA29_PF_VSYNC (GPIO_PORTA | GPIO_OUT | GPIO_PF | 29) +#define PA30_PF_CONTRAST (GPIO_PORTA | GPIO_OUT | GPIO_PF | 30) +#define PA31_PF_OE_ACD (GPIO_PORTA | GPIO_OUT | GPIO_PF | 31) +#define PB10_PF_CSI_D0 (GPIO_PORTB | GPIO_OUT | GPIO_PF | 10) +#define PB10_AF_UART6_TXD (GPIO_PORTB | GPIO_OUT | GPIO_AF | 10) +#define PB11_PF_CSI_D1 (GPIO_PORTB | GPIO_OUT | GPIO_PF | 11) +#define PB11_AF_UART6_RXD (GPIO_PORTB | GPIO_IN | GPIO_AF | 11) +#define PB12_PF_CSI_D2 (GPIO_PORTB | GPIO_OUT | GPIO_PF | 12) +#define PB12_AF_UART6_CTS (GPIO_PORTB | GPIO_OUT | GPIO_AF | 12) +#define PB13_PF_CSI_D3 (GPIO_PORTB | GPIO_OUT | GPIO_PF | 13) +#define PB13_AF_UART6_RTS (GPIO_PORTB | GPIO_IN | GPIO_AF | 13) +#define PB14_PF_CSI_D4 (GPIO_PORTB | GPIO_OUT | GPIO_PF | 14) +#define PB15_PF_CSI_MCLK (GPIO_PORTB | GPIO_OUT | GPIO_PF | 15) +#define PB16_PF_CSI_PIXCLK (GPIO_PORTB | GPIO_OUT | GPIO_PF | 16) +#define PB17_PF_CSI_D5 (GPIO_PORTB | GPIO_OUT | GPIO_PF | 17) +#define PB18_PF_CSI_D6 (GPIO_PORTB | GPIO_OUT | GPIO_PF | 18) +#define PB18_AF_UART5_TXD (GPIO_PORTB | GPIO_OUT | GPIO_AF | 18) +#define PB19_PF_CSI_D7 (GPIO_PORTB | GPIO_OUT | GPIO_PF | 19) +#define PB19_AF_UART5_RXD (GPIO_PORTB | GPIO_IN | GPIO_AF | 19) +#define PB20_PF_CSI_VSYNC (GPIO_PORTB | GPIO_OUT | GPIO_PF | 20) +#define PB20_AF_UART5_CTS (GPIO_PORTB | GPIO_OUT | GPIO_AF | 20) +#define PB21_PF_CSI_HSYNC (GPIO_PORTB | GPIO_OUT | GPIO_PF | 21) +#define PB21_AF_UART5_RTS (GPIO_PORTB | GPIO_IN | GPIO_AF | 21) +#define PB26_AF_UART4_RTS (GPIO_PORTB | GPIO_IN | GPIO_PF | 26) +#define PB28_AF_UART4_TXD (GPIO_PORTB | GPIO_OUT | GPIO_AF | 28) +#define PB29_AF_UART4_CTS (GPIO_PORTB | GPIO_OUT | GPIO_AF | 29) +#define PB31_AF_UART4_RXD (GPIO_PORTB | GPIO_IN | GPIO_AF | 31) +#define PC5_PF_I2C2_SDA (GPIO_PORTC | GPIO_IN | GPIO_PF | 5) +#define PC6_PF_I2C2_SCL (GPIO_PORTC | GPIO_IN | GPIO_PF | 6) +#define PC16_PF_SSI4_FS (GPIO_PORTC | GPIO_IN | GPIO_PF | 16) +#define PC17_PF_SSI4_RXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 17) +#define PC18_PF_SSI4_TXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 18) +#define PC19_PF_SSI4_CLK (GPIO_PORTC | GPIO_IN | GPIO_PF | 19) +#define PC20_PF_SSI1_FS (GPIO_PORTC | GPIO_IN | GPIO_PF | 20) +#define PC21_PF_SSI1_RXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 21) +#define PC22_PF_SSI1_TXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 22) +#define PC23_PF_SSI1_CLK (GPIO_PORTC | GPIO_IN | GPIO_PF | 23) +#define PC24_PF_SSI2_FS (GPIO_PORTC | GPIO_IN | GPIO_PF | 24) +#define PC25_PF_SSI2_RXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 25) +#define PC26_PF_SSI2_TXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 26) +#define PC27_PF_SSI2_CLK (GPIO_PORTC | GPIO_IN | GPIO_PF | 27) +#define PC28_PF_SSI3_FS (GPIO_PORTC | GPIO_IN | GPIO_PF | 28) +#define PC29_PF_SSI3_RXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 29) +#define PC30_PF_SSI3_TXD (GPIO_PORTC | GPIO_IN | GPIO_PF | 30) +#define PC31_PF_SSI3_CLK (GPIO_PORTC | GPIO_IN | GPIO_PF | 31) +#define PD0_AIN_FEC_TXD0 (GPIO_PORTD | GPIO_OUT | GPIO_AIN | 0) +#define PD1_AIN_FEC_TXD1 (GPIO_PORTD | GPIO_OUT | GPIO_AIN | 1) +#define PD2_AIN_FEC_TXD2 (GPIO_PORTD | GPIO_OUT | GPIO_AIN | 2) +#define PD3_AIN_FEC_TXD3 (GPIO_PORTD | GPIO_OUT | GPIO_AIN | 3) +#define PD4_AOUT_FEC_RX_ER (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 4) +#define PD5_AOUT_FEC_RXD1 (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 5) +#define PD6_AOUT_FEC_RXD2 (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 6) +#define PD7_AOUT_FEC_RXD3 (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 7) +#define PD8_AF_FEC_MDIO (GPIO_PORTD | GPIO_IN | GPIO_AF | 8) +#define PD9_AIN_FEC_MDC (GPIO_PORTD | GPIO_OUT | GPIO_AIN | 9) +#define PD10_AOUT_FEC_CRS (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 10) +#define PD11_AOUT_FEC_TX_CLK (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 11) +#define PD12_AOUT_FEC_RXD0 (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 12) +#define PD13_AOUT_FEC_RX_DV (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 13) +#define PD14_AOUT_FEC_CLR (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 14) +#define PD15_AOUT_FEC_COL (GPIO_PORTD | GPIO_IN | GPIO_AOUT | 15) +#define PD16_AIN_FEC_TX_ER (GPIO_PORTD | GPIO_OUT | GPIO_AIN | 16) +#define PD17_PF_I2C_DATA (GPIO_PORTD | GPIO_OUT | GPIO_PF | 17) +#define PD18_PF_I2C_CLK (GPIO_PORTD | GPIO_OUT | GPIO_PF | 18) +#define PD25_PF_CSPI1_RDY (GPIO_PORTD | GPIO_OUT | GPIO_PF | 25) +#define PD26_PF_CSPI1_SS2 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 26) +#define PD27_PF_CSPI1_SS1 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 27) +#define PD28_PF_CSPI1_SS0 (GPIO_PORTD | GPIO_OUT | GPIO_PF | 28) +#define PD29_PF_CSPI1_SCLK (GPIO_PORTD | GPIO_OUT | GPIO_PF | 29) +#define PD30_PF_CSPI1_MISO (GPIO_PORTD | GPIO_IN | GPIO_PF | 30) +#define PD31_PF_CSPI1_MOSI (GPIO_PORTD | GPIO_OUT | GPIO_PF | 31) +#define PF23_AIN_FEC_TX_EN (GPIO_PORTF | GPIO_OUT | GPIO_AIN | 23) +#define PE3_PF_UART2_CTS (GPIO_PORTE | GPIO_OUT | GPIO_PF | 3) +#define PE4_PF_UART2_RTS (GPIO_PORTE | GPIO_IN | GPIO_PF | 4) +#define PE6_PF_UART2_TXD (GPIO_PORTE | GPIO_OUT | GPIO_PF | 6) +#define PE7_PF_UART2_RXD (GPIO_PORTE | GPIO_IN | GPIO_PF | 7) +#define PE8_PF_UART3_TXD (GPIO_PORTE | GPIO_OUT | GPIO_PF | 8) +#define PE9_PF_UART3_RXD (GPIO_PORTE | GPIO_IN | GPIO_PF | 9) +#define PE10_PF_UART3_CTS (GPIO_PORTE | GPIO_OUT | GPIO_PF | 10) +#define PE11_PF_UART3_RTS (GPIO_PORTE | GPIO_IN | GPIO_PF | 11) +#define PE12_PF_UART1_TXD (GPIO_PORTE | GPIO_OUT | GPIO_PF | 12) +#define PE13_PF_UART1_RXD (GPIO_PORTE | GPIO_IN | GPIO_PF | 13) +#define PE14_PF_UART1_CTS (GPIO_PORTE | GPIO_OUT | GPIO_PF | 14) +#define PE15_PF_UART1_RTS (GPIO_PORTE | GPIO_IN | GPIO_PF | 15) +#define PE18_AF_CSPI3_MISO (GPIO_PORTE | GPIO_IN | GPIO_AF | 18) +#define PE21_AF_CSPI3_SS (GPIO_PORTE | GPIO_OUT | GPIO_AF | 21) +#define PE22_AF_CSPI3_MOSI (GPIO_PORTE | GPIO_OUT | GPIO_AF | 22) +#define PE23_AF_CSPI3_SCLK (GPIO_PORTE | GPIO_OUT | GPIO_AF | 23) +#endif + +/* decode irq number to use with IMR(x), ISR(x) and friends */ +#define IRQ_TO_REG(irq) ((irq - MXC_MAX_INT_LINES) >> 5) + +#define IRQ_GPIOA(x) (MXC_MAX_INT_LINES + x) +#define IRQ_GPIOB(x) (IRQ_GPIOA(32) + x) +#define IRQ_GPIOC(x) (IRQ_GPIOB(32) + x) +#define IRQ_GPIOD(x) (IRQ_GPIOC(32) + x) + +#endif /* _MXC_GPIO_MX1_MX2_H */ -- cgit v1.2.3 From 32dc80c9cb13a7ce686bcc26efcf39e35719b466 Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:02:56 +0200 Subject: i.MX2 family: Add basic mach support (headers) This patch adds basic mach support for the mx2 processor family, based on the original freescale code and adapted to mainline kernel coding style. Signed-off-by: Juergen Beisert --- include/asm-arm/arch-mxc/hardware.h | 3 ++ include/asm-arm/arch-mxc/iim.h | 77 +++++++++++++++++++++++++++++++++++++ 2 files changed, 80 insertions(+) create mode 100644 include/asm-arm/arch-mxc/iim.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/hardware.h b/include/asm-arm/arch-mxc/hardware.h index 4ed2d8072d0..f841127ef75 100644 --- a/include/asm-arm/arch-mxc/hardware.h +++ b/include/asm-arm/arch-mxc/hardware.h @@ -26,6 +26,9 @@ # include #endif +#ifdef CONFIG_ARCH_MX2 +#endif + #include #endif /* __ASM_ARCH_MXC_HARDWARE_H__ */ diff --git a/include/asm-arm/arch-mxc/iim.h b/include/asm-arm/arch-mxc/iim.h new file mode 100644 index 00000000000..315bffadafd --- /dev/null +++ b/include/asm-arm/arch-mxc/iim.h @@ -0,0 +1,77 @@ +/* + * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright 2008 Juergen Beisert, kernel@pengutronix.de + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef __ASM_ARCH_MXC_IIM_H__ +#define __ASM_ARCH_MXC_IIM_H__ + +/* Register offsets */ +#define MXC_IIMSTAT 0x0000 +#define MXC_IIMSTATM 0x0004 +#define MXC_IIMERR 0x0008 +#define MXC_IIMEMASK 0x000C +#define MXC_IIMFCTL 0x0010 +#define MXC_IIMUA 0x0014 +#define MXC_IIMLA 0x0018 +#define MXC_IIMSDAT 0x001C +#define MXC_IIMPREV 0x0020 +#define MXC_IIMSREV 0x0024 +#define MXC_IIMPRG_P 0x0028 +#define MXC_IIMSCS0 0x002C +#define MXC_IIMSCS1 0x0030 +#define MXC_IIMSCS2 0x0034 +#define MXC_IIMSCS3 0x0038 +#define MXC_IIMFBAC0 0x0800 +#define MXC_IIMJAC 0x0804 +#define MXC_IIMHWV1 0x0808 +#define MXC_IIMHWV2 0x080C +#define MXC_IIMHAB0 0x0810 +#define MXC_IIMHAB1 0x0814 +/* Definitions for i.MX27 TO2 */ +#define MXC_IIMMAC 0x0814 +#define MXC_IIMPREV_FUSE 0x0818 +#define MXC_IIMSREV_FUSE 0x081C +#define MXC_IIMSJC_CHALL_0 0x0820 +#define MXC_IIMSJC_CHALL_7 0x083C +#define MXC_IIMFB0UC17 0x0840 +#define MXC_IIMFB0UC255 0x0BFC +#define MXC_IIMFBAC1 0x0C00 +/* Definitions for i.MX27 TO2 */ +#define MXC_IIMSUID 0x0C04 +#define MXC_IIMKEY0 0x0C04 +#define MXC_IIMKEY20 0x0C54 +#define MXC_IIMSJC_RESP_0 0x0C58 +#define MXC_IIMSJC_RESP_7 0x0C74 +#define MXC_IIMFB1UC30 0x0C78 +#define MXC_IIMFB1UC255 0x0FFC + +/* Bit definitions */ + +#define MXC_IIMHWV1_WLOCK (0x1 << 7) +#define MXC_IIMHWV1_MCU_ENDIAN (0x1 << 6) +#define MXC_IIMHWV1_DSP_ENDIAN (0x1 << 5) +#define MXC_IIMHWV1_BOOT_INT (0x1 << 4) +#define MXC_IIMHWV1_SCC_DISABLE (0x1 << 3) +#define MXC_IIMHWV1_HANTRO_DISABLE (0x1 << 2) +#define MXC_IIMHWV1_MEMSTICK_DIS (0x1 << 1) + +#define MXC_IIMHWV2_WLOCK (0x1 << 7) +#define MXC_IIMHWV2_BP_SDMA (0x1 << 6) +#define MXC_IIMHWV2_SCM_DCM (0x1 << 5) + +#endif /* __ASM_ARCH_MXC_IIM_H__ */ -- cgit v1.2.3 From f31405cc4cc568baad28273c7f45b0563b57a17d Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:02:59 +0200 Subject: i.MX27 CPU: Add basic i.MX27 CPU support Add basic i.MX27 CPU support Signed-off-by: Juergen Beisert --- include/asm-arm/arch-mxc/hardware.h | 3 + include/asm-arm/arch-mxc/mx27.h | 302 ++++++++++++++++++++++++++++++++++++ include/asm-arm/arch-mxc/mxc.h | 4 + 3 files changed, 309 insertions(+) create mode 100644 include/asm-arm/arch-mxc/mx27.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/hardware.h b/include/asm-arm/arch-mxc/hardware.h index f841127ef75..37cddbaaade 100644 --- a/include/asm-arm/arch-mxc/hardware.h +++ b/include/asm-arm/arch-mxc/hardware.h @@ -27,6 +27,9 @@ #endif #ifdef CONFIG_ARCH_MX2 +# ifdef CONFIG_MACH_MX27 +# include +# endif #endif #include diff --git a/include/asm-arm/arch-mxc/mx27.h b/include/asm-arm/arch-mxc/mx27.h new file mode 100644 index 00000000000..212ecc24662 --- /dev/null +++ b/include/asm-arm/arch-mxc/mx27.h @@ -0,0 +1,302 @@ +/* + * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright 2008 Juergen Beisert, kernel@pengutronix.de + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef __ASM_ARCH_MXC_MX27_H__ +#define __ASM_ARCH_MXC_MX27_H__ + +#ifndef __ASM_ARCH_MXC_HARDWARE_H__ +#error "Do not include directly." +#endif + +/* IRAM */ +#define IRAM_BASE_ADDR 0xFFFF4C00 /* internal ram */ + +/* Register offests */ +#define AIPI_BASE_ADDR 0x10000000 +#define AIPI_BASE_ADDR_VIRT 0xF4000000 +#define AIPI_SIZE SZ_1M + +#define DMA_BASE_ADDR (AIPI_BASE_ADDR + 0x01000) +#define WDOG_BASE_ADDR (AIPI_BASE_ADDR + 0x02000) +#define GPT1_BASE_ADDR (AIPI_BASE_ADDR + 0x03000) +#define GPT2_BASE_ADDR (AIPI_BASE_ADDR + 0x04000) +#define GPT3_BASE_ADDR (AIPI_BASE_ADDR + 0x05000) +#define PWM_BASE_ADDR (AIPI_BASE_ADDR + 0x06000) +#define RTC_BASE_ADDR (AIPI_BASE_ADDR + 0x07000) +#define KPP_BASE_ADDR (AIPI_BASE_ADDR + 0x08000) +#define OWIRE_BASE_ADDR (AIPI_BASE_ADDR + 0x09000) +#define UART1_BASE_ADDR (AIPI_BASE_ADDR + 0x0A000) +#define UART2_BASE_ADDR (AIPI_BASE_ADDR + 0x0B000) +#define UART3_BASE_ADDR (AIPI_BASE_ADDR + 0x0C000) +#define UART4_BASE_ADDR (AIPI_BASE_ADDR + 0x0D000) +#define CSPI1_BASE_ADDR (AIPI_BASE_ADDR + 0x0E000) +#define CSPI2_BASE_ADDR (AIPI_BASE_ADDR + 0x0F000) +#define SSI1_BASE_ADDR (AIPI_BASE_ADDR + 0x10000) +#define SSI2_BASE_ADDR (AIPI_BASE_ADDR + 0x11000) +#define I2C_BASE_ADDR (AIPI_BASE_ADDR + 0x12000) +#define SDHC1_BASE_ADDR (AIPI_BASE_ADDR + 0x13000) +#define SDHC2_BASE_ADDR (AIPI_BASE_ADDR + 0x14000) +#define GPIO_BASE_ADDR (AIPI_BASE_ADDR + 0x15000) +#define AUDMUX_BASE_ADDR (AIPI_BASE_ADDR + 0x16000) + +#define CSPI3_BASE_ADDR (AIPI_BASE_ADDR + 0x17000) +#define MSHC_BASE_ADDR (AIPI_BASE_ADDR + 0x18000) +#define GPT5_BASE_ADDR (AIPI_BASE_ADDR + 0x19000) +#define GPT4_BASE_ADDR (AIPI_BASE_ADDR + 0x1A000) +#define UART5_BASE_ADDR (AIPI_BASE_ADDR + 0x1B000) +#define UART6_BASE_ADDR (AIPI_BASE_ADDR + 0x1C000) +#define I2C2_BASE_ADDR (AIPI_BASE_ADDR + 0x1D000) +#define SDHC3_BASE_ADDR (AIPI_BASE_ADDR + 0x1E000) +#define GPT6_BASE_ADDR (AIPI_BASE_ADDR + 0x1F000) + +#define LCDC_BASE_ADDR (AIPI_BASE_ADDR + 0x21000) +#define SLCDC_BASE_ADDR (AIPI_BASE_ADDR + 0x22000) +#define VPU_BASE_ADDR (AIPI_BASE_ADDR + 0x23000) +#define USBOTG_BASE_ADDR (AIPI_BASE_ADDR + 0x24000) +/* for mx27*/ +#define OTG_BASE_ADDR USBOTG_BASE_ADDR +#define SAHARA_BASE_ADDR (AIPI_BASE_ADDR + 0x25000) +#define EMMA_BASE_ADDR (AIPI_BASE_ADDR + 0x26400) +#define CCM_BASE_ADDR (AIPI_BASE_ADDR + 0x27000) +#define SYSCTRL_BASE_ADDR (AIPI_BASE_ADDR + 0x27800) +#define IIM_BASE_ADDR (AIPI_BASE_ADDR + 0x28000) + +#define RTIC_BASE_ADDR (AIPI_BASE_ADDR + 0x2A000) +#define FEC_BASE_ADDR (AIPI_BASE_ADDR + 0x2B000) +#define SCC_BASE_ADDR (AIPI_BASE_ADDR + 0x2C000) +#define ETB_BASE_ADDR (AIPI_BASE_ADDR + 0x3B000) +#define ETB_RAM_BASE_ADDR (AIPI_BASE_ADDR + 0x3C000) + +#define JAM_BASE_ADDR (AIPI_BASE_ADDR + 0x3E000) +#define MAX_BASE_ADDR (AIPI_BASE_ADDR + 0x3F000) + +/* ROMP and AVIC */ +#define ROMP_BASE_ADDR 0x10041000 + +#define AVIC_BASE_ADDR 0x10040000 + +#define SAHB1_BASE_ADDR 0x80000000 +#define SAHB1_BASE_ADDR_VIRT 0xF4100000 +#define SAHB1_SIZE SZ_1M + +#define CSI_BASE_ADDR (SAHB1_BASE_ADDR + 0x0000) +#define ATA_BASE_ADDR (SAHB1_BASE_ADDR + 0x1000) + +/* NAND, SDRAM, WEIM, M3IF, EMI controllers */ +#define X_MEMC_BASE_ADDR 0xD8000000 +#define X_MEMC_BASE_ADDR_VIRT 0xF4200000 +#define X_MEMC_SIZE SZ_1M + +#define NFC_BASE_ADDR (X_MEMC_BASE_ADDR) +#define SDRAMC_BASE_ADDR (X_MEMC_BASE_ADDR + 0x1000) +#define WEIM_BASE_ADDR (X_MEMC_BASE_ADDR + 0x2000) +#define M3IF_BASE_ADDR (X_MEMC_BASE_ADDR + 0x3000) +#define PCMCIA_CTL_BASE_ADDR (X_MEMC_BASE_ADDR + 0x4000) + +/* Memory regions and CS */ +#define SDRAM_BASE_ADDR 0xA0000000 +#define CSD1_BASE_ADDR 0xB0000000 + +#define CS0_BASE_ADDR 0xC0000000 +#define CS1_BASE_ADDR 0xC8000000 +#define CS2_BASE_ADDR 0xD0000000 +#define CS3_BASE_ADDR 0xD2000000 +#define CS4_BASE_ADDR 0xD4000000 +#define CS5_BASE_ADDR 0xD6000000 +#define PCMCIA_MEM_BASE_ADDR 0xDC000000 + +/* + * This macro defines the physical to virtual address mapping for all the + * peripheral modules. It is used by passing in the physical address as x + * and returning the virtual address. If the physical address is not mapped, + * it returns 0xDEADBEEF + */ +#define IO_ADDRESS(x) \ + (((x >= AIPI_BASE_ADDR) && (x < (AIPI_BASE_ADDR + AIPI_SIZE))) ? \ + AIPI_IO_ADDRESS(x) : \ + ((x >= SAHB1_BASE_ADDR) && (x < (SAHB1_BASE_ADDR + SAHB1_SIZE))) ? \ + SAHB1_IO_ADDRESS(x) : \ + ((x >= X_MEMC_BASE_ADDR) && (x < (X_MEMC_BASE_ADDR + X_MEMC_SIZE))) ? \ + X_MEMC_IO_ADDRESS(x) : 0xDEADBEEF) + +/* define the address mapping macros: in physical address order */ +#define AIPI_IO_ADDRESS(x) \ + (((x) - AIPI_BASE_ADDR) + AIPI_BASE_ADDR_VIRT) + +#define AVIC_IO_ADDRESS(x) AIPI_IO_ADDRESS(x) + +#define SAHB1_IO_ADDRESS(x) \ + (((x) - SAHB1_BASE_ADDR) + SAHB1_BASE_ADDR_VIRT) + +#define CS4_IO_ADDRESS(x) \ + (((x) - CS4_BASE_ADDR) + CS4_BASE_ADDR_VIRT) + +#define X_MEMC_IO_ADDRESS(x) \ + (((x) - X_MEMC_BASE_ADDR) + X_MEMC_BASE_ADDR_VIRT) + +#define PCMCIA_IO_ADDRESS(x) \ + (((x) - X_MEMC_BASE_ADDR) + X_MEMC_BASE_ADDR_VIRT) + +/* fixed interrput numbers */ +#define MXC_INT_CCM 63 +#define MXC_INT_IIM 62 +#define MXC_INT_LCDC 61 +#define MXC_INT_SLCDC 60 +#define MXC_INT_SAHARA 59 +#define MXC_INT_SCC_SCM 58 +#define MXC_INT_SCC_SMN 57 +#define MXC_INT_USB3 56 +#define MXC_INT_USB2 55 +#define MXC_INT_USB1 54 +#define MXC_INT_VPU 53 +#define MXC_INT_EMMAPP 52 +#define MXC_INT_EMMAPRP 51 +#define MXC_INT_FEC 50 +#define MXC_INT_UART5 49 +#define MXC_INT_UART6 48 +#define MXC_INT_DMACH15 47 +#define MXC_INT_DMACH14 46 +#define MXC_INT_DMACH13 45 +#define MXC_INT_DMACH12 44 +#define MXC_INT_DMACH11 43 +#define MXC_INT_DMACH10 42 +#define MXC_INT_DMACH9 41 +#define MXC_INT_DMACH8 40 +#define MXC_INT_DMACH7 39 +#define MXC_INT_DMACH6 38 +#define MXC_INT_DMACH5 37 +#define MXC_INT_DMACH4 36 +#define MXC_INT_DMACH3 35 +#define MXC_INT_DMACH2 34 +#define MXC_INT_DMACH1 33 +#define MXC_INT_DMACH0 32 +#define MXC_INT_CSI 31 +#define MXC_INT_ATA 30 +#define MXC_INT_NANDFC 29 +#define MXC_INT_PCMCIA 28 +#define MXC_INT_WDOG 27 +#define MXC_INT_GPT1 26 +#define MXC_INT_GPT2 25 +#define MXC_INT_GPT3 24 +#define MXC_INT_GPT INT_GPT1 +#define MXC_INT_PWM 23 +#define MXC_INT_RTC 22 +#define MXC_INT_KPP 21 +#define MXC_INT_UART1 20 +#define MXC_INT_UART2 19 +#define MXC_INT_UART3 18 +#define MXC_INT_UART4 17 +#define MXC_INT_CSPI1 16 +#define MXC_INT_CSPI2 15 +#define MXC_INT_SSI1 14 +#define MXC_INT_SSI2 13 +#define MXC_INT_I2C 12 +#define MXC_INT_SDHC1 11 +#define MXC_INT_SDHC2 10 +#define MXC_INT_SDHC3 9 +#define MXC_INT_GPIO 8 +#define MXC_INT_SDHC 7 +#define MXC_INT_CSPI3 6 +#define MXC_INT_RTIC 5 +#define MXC_INT_GPT4 4 +#define MXC_INT_GPT5 3 +#define MXC_INT_GPT6 2 +#define MXC_INT_I2C2 1 + +/* fixed DMA request numbers */ +#define DMA_REQ_NFC 37 +#define DMA_REQ_SDHC3 36 +#define DMA_REQ_UART6_RX 35 +#define DMA_REQ_UART6_TX 34 +#define DMA_REQ_UART5_RX 33 +#define DMA_REQ_UART5_TX 32 +#define DMA_REQ_CSI_RX 31 +#define DMA_REQ_CSI_STAT 30 +#define DMA_REQ_ATA_RCV 29 +#define DMA_REQ_ATA_TX 28 +#define DMA_REQ_UART1_TX 27 +#define DMA_REQ_UART1_RX 26 +#define DMA_REQ_UART2_TX 25 +#define DMA_REQ_UART2_RX 24 +#define DMA_REQ_UART3_TX 23 +#define DMA_REQ_UART3_RX 22 +#define DMA_REQ_UART4_TX 21 +#define DMA_REQ_UART4_RX 20 +#define DMA_REQ_CSPI1_TX 19 +#define DMA_REQ_CSPI1_RX 18 +#define DMA_REQ_CSPI2_TX 17 +#define DMA_REQ_CSPI2_RX 16 +#define DMA_REQ_SSI1_TX1 15 +#define DMA_REQ_SSI1_RX1 14 +#define DMA_REQ_SSI1_TX0 13 +#define DMA_REQ_SSI1_RX0 12 +#define DMA_REQ_SSI2_TX1 11 +#define DMA_REQ_SSI2_RX1 10 +#define DMA_REQ_SSI2_TX0 9 +#define DMA_REQ_SSI2_RX0 8 +#define DMA_REQ_SDHC1 7 +#define DMA_REQ_SDHC2 6 +#define DMA_REQ_MSHC 4 +#define DMA_REQ_EXT 3 +#define DMA_REQ_CSPI3_TX 2 +#define DMA_REQ_CSPI3_RX 1 + +/* silicon revisions specific to i.MX27 */ +#define CHIP_REV_1_0 0x00 +#define CHIP_REV_2_0 0x01 + +#ifndef __ASSEMBLY__ +extern int mx27_revision(void); +#endif + +/* gpio and gpio based interrupt handling */ +#define GPIO_DR 0x1C +#define GPIO_GDIR 0x00 +#define GPIO_PSR 0x24 +#define GPIO_ICR1 0x28 +#define GPIO_ICR2 0x2C +#define GPIO_IMR 0x30 +#define GPIO_ISR 0x34 +#define GPIO_INT_LOW_LEV 0x3 +#define GPIO_INT_HIGH_LEV 0x2 +#define GPIO_INT_RISE_EDGE 0x0 +#define GPIO_INT_FALL_EDGE 0x1 +#define GPIO_INT_NONE 0x4 + +/* Mandatory defines used globally */ + +/* this is an i.MX27 CPU */ +#define cpu_is_mx27() (1) + +/* this CPU supports up to 192 GPIOs (don't forget the baseboard!) */ +#define ARCH_NR_GPIOS (192 + 16) + +/* OS clock tick rate */ +#define CLOCK_TICK_RATE 13300000 + +/* Start of RAM */ +#define PHYS_OFFSET SDRAM_BASE_ADDR + +/* max interrupt lines count */ +#define NR_IRQS 256 + +/* count of internal interrupt sources */ +#define MXC_MAX_INT_LINES 64 + +#endif /* __ASM_ARCH_MXC_MX27_H__ */ diff --git a/include/asm-arm/arch-mxc/mxc.h b/include/asm-arm/arch-mxc/mxc.h index 3e1c4ded18e..332eda4dbd3 100644 --- a/include/asm-arm/arch-mxc/mxc.h +++ b/include/asm-arm/arch-mxc/mxc.h @@ -29,4 +29,8 @@ # define cpu_is_mx31() (0) #endif +#ifndef CONFIG_MACH_MX27 +# define cpu_is_mx27() (0) +#endif + #endif /* __ASM_ARCH_MXC_H__ */ -- cgit v1.2.3 From 80eedae6f0322dafc749140b67986b2472473745 Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:03:00 +0200 Subject: i.MX27: Add ADS platform support This patch adds basic support for the Freescale MX27ADS reference board. Currently only a serial console can be used. Signed-off-by: Juergen Beisert --- include/asm-arm/arch-mxc/board-mx27ads.h | 354 +++++++++++++++++++++++++++++++ include/asm-arm/arch-mxc/debug-macro.S | 4 +- 2 files changed, 357 insertions(+), 1 deletion(-) create mode 100644 include/asm-arm/arch-mxc/board-mx27ads.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/board-mx27ads.h b/include/asm-arm/arch-mxc/board-mx27ads.h new file mode 100644 index 00000000000..61e66dac90e --- /dev/null +++ b/include/asm-arm/arch-mxc/board-mx27ads.h @@ -0,0 +1,354 @@ +/* + * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved. + */ + +/* + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __ASM_ARCH_MXC_BOARD_MX27ADS_H__ +#define __ASM_ARCH_MXC_BOARD_MX27ADS_H__ + +/* external interrupt multiplexer */ +#define MXC_EXP_IO_BASE (MXC_GPIO_BASE + MXC_MAX_GPIO_LINES) + +#define MXC_VIRTUAL_INTS_BASE (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES) +#define MXC_SDIO1_CARD_IRQ MXC_VIRTUAL_INTS_BASE +#define MXC_SDIO2_CARD_IRQ (MXC_VIRTUAL_INTS_BASE + 1) +#define MXC_SDIO3_CARD_IRQ (MXC_VIRTUAL_INTS_BASE + 2) + +#define MXC_MAX_BOARD_INTS (MXC_MAX_EXP_IO_LINES + \ + MXC_MAX_VIRTUAL_INTS) + +/* + * MXC UART EVB board level configurations + */ + +#define MXC_LL_EXTUART_PADDR (CS4_BASE_ADDR + 0x20000) +#define MXC_LL_EXTUART_VADDR (CS4_BASE_ADDR_VIRT + 0x20000) +#define MXC_LL_EXTUART_16BIT_BUS + +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR AIPI_IO_ADDRESS(UART1_BASE_ADDR) + +/* + * @name Memory Size parameters + */ + +/* + * Size of SDRAM memory + */ +#define SDRAM_MEM_SIZE SZ_128M + +/* + * PBC Controller parameters + */ + +/* + * Base address of PBC controller, CS4 + */ +#define PBC_BASE_ADDRESS 0xEB000000 +#define PBC_REG_ADDR(offset) (PBC_BASE_ADDRESS + (offset)) + +/* + * PBC Interupt name definitions + */ +#define PBC_GPIO1_0 0 +#define PBC_GPIO1_1 1 +#define PBC_GPIO1_2 2 +#define PBC_GPIO1_3 3 +#define PBC_GPIO1_4 4 +#define PBC_GPIO1_5 5 + +#define PBC_INTR_MAX_NUM 6 +#define PBC_INTR_SHARED_MAX_NUM 8 + +/* When the PBC address connection is fixed in h/w, defined as 1 */ +#define PBC_ADDR_SH 0 + +/* Offsets for the PBC Controller register */ +/* + * PBC Board version register offset + */ +#define PBC_VERSION_REG PBC_REG_ADDR(0x00000 >> PBC_ADDR_SH) +/* + * PBC Board control register 1 set address. + */ +#define PBC_BCTRL1_SET_REG PBC_REG_ADDR(0x00008 >> PBC_ADDR_SH) +/* + * PBC Board control register 1 clear address. + */ +#define PBC_BCTRL1_CLEAR_REG PBC_REG_ADDR(0x0000C >> PBC_ADDR_SH) +/* + * PBC Board control register 2 set address. + */ +#define PBC_BCTRL2_SET_REG PBC_REG_ADDR(0x00010 >> PBC_ADDR_SH) +/* + * PBC Board control register 2 clear address. + */ +#define PBC_BCTRL2_CLEAR_REG PBC_REG_ADDR(0x00014 >> PBC_ADDR_SH) +/* + * PBC Board control register 3 set address. + */ +#define PBC_BCTRL3_SET_REG PBC_REG_ADDR(0x00018 >> PBC_ADDR_SH) +/* + * PBC Board control register 3 clear address. + */ +#define PBC_BCTRL3_CLEAR_REG PBC_REG_ADDR(0x0001C >> PBC_ADDR_SH) +/* + * PBC Board control register 3 set address. + */ +#define PBC_BCTRL4_SET_REG PBC_REG_ADDR(0x00020 >> PBC_ADDR_SH) +/* + * PBC Board control register 4 clear address. + */ +#define PBC_BCTRL4_CLEAR_REG PBC_REG_ADDR(0x00024 >> PBC_ADDR_SH) +/*PBC_ADDR_SH + * PBC Board status register 1. + */ +#define PBC_BSTAT1_REG PBC_REG_ADDR(0x00028 >> PBC_ADDR_SH) +/* + * PBC Board interrupt status register. + */ +#define PBC_INTSTATUS_REG PBC_REG_ADDR(0x0002C >> PBC_ADDR_SH) +/* + * PBC Board interrupt current status register. + */ +#define PBC_INTCURR_STATUS_REG PBC_REG_ADDR(0x00034 >> PBC_ADDR_SH) +/* + * PBC Interrupt mask register set address. + */ +#define PBC_INTMASK_SET_REG PBC_REG_ADDR(0x00038 >> PBC_ADDR_SH) +/* + * PBC Interrupt mask register clear address. + */ +#define PBC_INTMASK_CLEAR_REG PBC_REG_ADDR(0x0003C >> PBC_ADDR_SH) +/* + * External UART A. + */ +#define PBC_SC16C652_UARTA_REG PBC_REG_ADDR(0x20000 >> PBC_ADDR_SH) +/* + * UART 4 Expanding Signal Status. + */ +#define PBC_UART_STATUS_REG PBC_REG_ADDR(0x22000 >> PBC_ADDR_SH) +/* + * UART 4 Expanding Signal Control Set. + */ +#define PBC_UCTRL_SET_REG PBC_REG_ADDR(0x24000 >> PBC_ADDR_SH) +/* + * UART 4 Expanding Signal Control Clear. + */ +#define PBC_UCTRL_CLR_REG PBC_REG_ADDR(0x26000 >> PBC_ADDR_SH) +/* + * Ethernet Controller IO base address. + */ +#define PBC_CS8900A_IOBASE_REG PBC_REG_ADDR(0x40000 >> PBC_ADDR_SH) +/* + * Ethernet Controller Memory base address. + */ +#define PBC_CS8900A_MEMBASE_REG PBC_REG_ADDR(0x42000 >> PBC_ADDR_SH) +/* + * Ethernet Controller DMA base address. + */ +#define PBC_CS8900A_DMABASE_REG PBC_REG_ADDR(0x44000 >> PBC_ADDR_SH) + +/* PBC Board Version Register bit definition */ +#define PBC_VERSION_ADS 0x8000 /* Bit15=1 means version for ads */ +#define PBC_VERSION_EVB_REVB 0x4000 /* BIT14=1 means version for evb revb */ + +/* PBC Board Control Register 1 bit definitions */ +#define PBC_BCTRL1_ERST 0x0001 /* Ethernet Reset */ +#define PBC_BCTRL1_URST 0x0002 /* Reset External UART controller */ +#define PBC_BCTRL1_FRST 0x0004 /* FEC Reset */ +#define PBC_BCTRL1_ESLEEP 0x0010 /* Enable ethernet Sleep */ +#define PBC_BCTRL1_LCDON 0x0800 /* Enable the LCD */ + +/* PBC Board Control Register 2 bit definitions */ +#define PBC_BCTRL2_VCC_EN 0x0004 /* Enable VCC */ +#define PBC_BCTRL2_VPP_EN 0x0008 /* Enable Vpp */ +#define PBC_BCTRL2_ATAFEC_EN 0X0010 +#define PBC_BCTRL2_ATAFEC_SEL 0X0020 +#define PBC_BCTRL2_ATA_EN 0X0040 +#define PBC_BCTRL2_IRDA_SD 0X0080 +#define PBC_BCTRL2_IRDA_EN 0X0100 +#define PBC_BCTRL2_CCTL10 0X0200 +#define PBC_BCTRL2_CCTL11 0X0400 + +/* PBC Board Control Register 3 bit definitions */ +#define PBC_BCTRL3_HSH_EN 0X0020 +#define PBC_BCTRL3_FSH_MOD 0X0040 +#define PBC_BCTRL3_OTG_HS_EN 0X0080 +#define PBC_BCTRL3_OTG_VBUS_EN 0X0100 +#define PBC_BCTRL3_FSH_VBUS_EN 0X0200 +#define PBC_BCTRL3_USB_OTG_ON 0X0800 +#define PBC_BCTRL3_USB_FSH_ON 0X1000 + +/* PBC Board Control Register 4 bit definitions */ +#define PBC_BCTRL4_REGEN_SEL 0X0001 +#define PBC_BCTRL4_USER_OFF 0X0002 +#define PBC_BCTRL4_VIB_EN 0X0004 +#define PBC_BCTRL4_PWRGT1_EN 0X0008 +#define PBC_BCTRL4_PWRGT2_EN 0X0010 +#define PBC_BCTRL4_STDBY_PRI 0X0020 + +#ifndef __ASSEMBLY__ +/* + * Enumerations for SD cards and memory stick card. This corresponds to + * the card EN bits in the IMR: SD1_EN | MS_EN | SD3_EN | SD2_EN. + */ +enum mxc_card_no { + MXC_CARD_SD2 = 0, + MXC_CARD_SD3, + MXC_CARD_MS, + MXC_CARD_SD1, + MXC_CARD_MIN = MXC_CARD_SD2, + MXC_CARD_MAX = MXC_CARD_SD1, +}; +#endif + +#define MXC_CPLD_VER_1_50 0x01 + +/* + * PBC BSTAT Register bit definitions + */ +#define PBC_BSTAT_PRI_INT 0X0001 +#define PBC_BSTAT_USB_BYP 0X0002 +#define PBC_BSTAT_ATA_IOCS16 0X0004 +#define PBC_BSTAT_ATA_CBLID 0X0008 +#define PBC_BSTAT_ATA_DASP 0X0010 +#define PBC_BSTAT_PWR_RDY 0X0020 +#define PBC_BSTAT_SD3_WP 0X0100 +#define PBC_BSTAT_SD2_WP 0X0200 +#define PBC_BSTAT_SD1_WP 0X0400 +#define PBC_BSTAT_SD3_DET 0X0800 +#define PBC_BSTAT_SD2_DET 0X1000 +#define PBC_BSTAT_SD1_DET 0X2000 +#define PBC_BSTAT_MS_DET 0X4000 +#define PBC_BSTAT_SD3_DET_BIT 11 +#define PBC_BSTAT_SD2_DET_BIT 12 +#define PBC_BSTAT_SD1_DET_BIT 13 +#define PBC_BSTAT_MS_DET_BIT 14 +#define MXC_BSTAT_BIT(n) ((n == MXC_CARD_SD2) ? PBC_BSTAT_SD2_DET : \ + ((n == MXC_CARD_SD3) ? PBC_BSTAT_SD3_DET : \ + ((n == MXC_CARD_SD1) ? PBC_BSTAT_SD1_DET : \ + ((n == MXC_CARD_MS) ? PBC_BSTAT_MS_DET : \ + 0x0)))) + +/* + * PBC UART Control Register bit definitions + */ +#define PBC_UCTRL_DCE_DCD 0X0001 +#define PBC_UCTRL_DCE_DSR 0X0002 +#define PBC_UCTRL_DCE_RI 0X0004 +#define PBC_UCTRL_DTE_DTR 0X0100 + +/* + * PBC UART Status Register bit definitions + */ +#define PBC_USTAT_DTE_DCD 0X0001 +#define PBC_USTAT_DTE_DSR 0X0002 +#define PBC_USTAT_DTE_RI 0X0004 +#define PBC_USTAT_DCE_DTR 0X0100 + +/* + * PBC Interupt mask register bit definitions + */ +#define PBC_INTR_SD3_R_EN_BIT 4 +#define PBC_INTR_SD2_R_EN_BIT 0 +#define PBC_INTR_SD1_R_EN_BIT 6 +#define PBC_INTR_MS_R_EN_BIT 5 +#define PBC_INTR_SD3_EN_BIT 13 +#define PBC_INTR_SD2_EN_BIT 12 +#define PBC_INTR_MS_EN_BIT 14 +#define PBC_INTR_SD1_EN_BIT 15 + +#define PBC_INTR_SD2_R_EN 0x0001 +#define PBC_INTR_LOW_BAT 0X0002 +#define PBC_INTR_OTG_FSOVER 0X0004 +#define PBC_INTR_FSH_OVER 0X0008 +#define PBC_INTR_SD3_R_EN 0x0010 +#define PBC_INTR_MS_R_EN 0x0020 +#define PBC_INTR_SD1_R_EN 0x0040 +#define PBC_INTR_FEC_INT 0X0080 +#define PBC_INTR_ENET_INT 0X0100 +#define PBC_INTR_OTGFS_INT 0X0200 +#define PBC_INTR_XUART_INT 0X0400 +#define PBC_INTR_CCTL12 0X0800 +#define PBC_INTR_SD2_EN 0x1000 +#define PBC_INTR_SD3_EN 0x2000 +#define PBC_INTR_MS_EN 0x4000 +#define PBC_INTR_SD1_EN 0x8000 + + + +/* For interrupts like xuart, enet etc */ +#define EXPIO_PARENT_INT IOMUX_TO_IRQ(MX27_PIN_TIN) +#define MXC_MAX_EXP_IO_LINES 16 + +/* + * This corresponds to PBC_INTMASK_SET_REG at offset 0x38. + * + */ +#define EXPIO_INT_LOW_BAT (MXC_EXP_IO_BASE + 1) +#define EXPIO_INT_OTG_FS_OVR (MXC_EXP_IO_BASE + 2) +#define EXPIO_INT_FSH_OVR (MXC_EXP_IO_BASE + 3) +#define EXPIO_INT_RES4 (MXC_EXP_IO_BASE + 4) +#define EXPIO_INT_RES5 (MXC_EXP_IO_BASE + 5) +#define EXPIO_INT_RES6 (MXC_EXP_IO_BASE + 6) +#define EXPIO_INT_FEC (MXC_EXP_IO_BASE + 7) +#define EXPIO_INT_ENET_INT (MXC_EXP_IO_BASE + 8) +#define EXPIO_INT_OTG_FS_INT (MXC_EXP_IO_BASE + 9) +#define EXPIO_INT_XUART_INTA (MXC_EXP_IO_BASE + 10) +#define EXPIO_INT_CCTL12_INT (MXC_EXP_IO_BASE + 11) +#define EXPIO_INT_SD2_EN (MXC_EXP_IO_BASE + 12) +#define EXPIO_INT_SD3_EN (MXC_EXP_IO_BASE + 13) +#define EXPIO_INT_MS_EN (MXC_EXP_IO_BASE + 14) +#define EXPIO_INT_SD1_EN (MXC_EXP_IO_BASE + 15) + +/* + * This is System IRQ used by CS8900A for interrupt generation + * taken from platform.h + */ +#define CS8900AIRQ EXPIO_INT_ENET_INT +/* This is I/O Base address used to access registers of CS8900A on MXC ADS */ +#define CS8900A_BASE_ADDRESS (PBC_CS8900A_IOBASE_REG + 0x300) + +#define MXC_PMIC_INT_LINE IOMUX_TO_IRQ(MX27_PIN_TOUT) + +/* +* This is used to detect if the CPLD version is for mx27 evb board rev-a +*/ +#define PBC_CPLD_VERSION_IS_REVA() \ + ((__raw_readw(PBC_VERSION_REG) & \ + (PBC_VERSION_ADS | PBC_VERSION_EVB_REVB))\ + == 0) + +/* This is used to active or inactive ata signal in CPLD . + * It is dependent with hardware + */ +#define PBC_ATA_SIGNAL_ACTIVE() \ + __raw_writew( \ + PBC_BCTRL2_ATAFEC_EN|PBC_BCTRL2_ATAFEC_SEL|PBC_BCTRL2_ATA_EN, \ + PBC_BCTRL2_CLEAR_REG) + +#define PBC_ATA_SIGNAL_INACTIVE() \ + __raw_writew( \ + PBC_BCTRL2_ATAFEC_EN|PBC_BCTRL2_ATAFEC_SEL|PBC_BCTRL2_ATA_EN, \ + PBC_BCTRL2_SET_REG) + +#define MXC_BD_LED1 (1 << 5) +#define MXC_BD_LED2 (1 << 6) +#define MXC_BD_LED_ON(led) \ + __raw_writew(led, PBC_BCTRL1_SET_REG) +#define MXC_BD_LED_OFF(led) \ + __raw_writew(led, PBC_BCTRL1_CLEAR_REG) + +/* to determine the correct external crystal reference */ +#define CKIH_27MHZ_BIT_SET (1 << 3) + +#endif /* __ASM_ARCH_MXC_BOARD_MX27ADS_H__ */ diff --git a/include/asm-arm/arch-mxc/debug-macro.S b/include/asm-arm/arch-mxc/debug-macro.S index 5add48b6665..c6c56805143 100644 --- a/include/asm-arm/arch-mxc/debug-macro.S +++ b/include/asm-arm/arch-mxc/debug-macro.S @@ -22,7 +22,9 @@ #ifdef CONFIG_MACH_MX31LITE #include #endif - +#ifdef CONFIG_MACH_MX27ADS +#include +#endif .macro addruart,rx mrc p15, 0, \rx, c1, c0 tst \rx, #1 @ MMU enabled? -- cgit v1.2.3 From 7e5e9f5457f5cd019fd7e2f3da94e9fc72cc9ff6 Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:03:00 +0200 Subject: i.MX27: Adding PCM038 platform support This patch adds support for the phyCORE-i.MX27 cpu module (aka pcm038). It is as generic as possible in order to support any kind of baseboard. Note: This CPU module implementation can't work without a baseboard support. Baseboard support can be added by the PCM-970 (included in this patch stack) or any custom variant. Signed-off-by: Juergen Beisert --- include/asm-arm/arch-mxc/board-pcm038.h | 36 +++++++++++++++++++++++++++++++++ include/asm-arm/arch-mxc/debug-macro.S | 3 +++ 2 files changed, 39 insertions(+) create mode 100644 include/asm-arm/arch-mxc/board-pcm038.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/board-pcm038.h b/include/asm-arm/arch-mxc/board-pcm038.h new file mode 100644 index 00000000000..300467e8db6 --- /dev/null +++ b/include/asm-arm/arch-mxc/board-pcm038.h @@ -0,0 +1,36 @@ +/* + * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef __ASM_ARCH_MXC_BOARD_PCM038_H__ +#define __ASM_ARCH_MXC_BOARD_PCM038_H__ + +/* mandatory for CONFIG_LL_DEBUG */ + +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR (AIPI_BASE_ADDR_VIRT + 0x0A000) + +#ifndef __ASSEMBLY__ +/* + * This CPU module needs a baseboard to work. After basic initializing + * its own devices, it calls baseboard's init function. + * TODO: Add your own baseboard init function and call it from + * inside pcm038_init(). + */ +#endif + +#endif /* __ASM_ARCH_MXC_BOARD_PCM038_H__ */ diff --git a/include/asm-arm/arch-mxc/debug-macro.S b/include/asm-arm/arch-mxc/debug-macro.S index c6c56805143..575087f8561 100644 --- a/include/asm-arm/arch-mxc/debug-macro.S +++ b/include/asm-arm/arch-mxc/debug-macro.S @@ -24,6 +24,9 @@ #endif #ifdef CONFIG_MACH_MX27ADS #include +#endif +#ifdef CONFIG_MACH_PCM038 +#include #endif .macro addruart,rx mrc p15, 0, \rx, c1, c0 -- cgit v1.2.3 From ff6552e4f3505da9c2886098773146be71c872e3 Mon Sep 17 00:00:00 2001 From: Juergen Beisert Date: Sat, 5 Jul 2008 10:03:01 +0200 Subject: i.MX27 family: Add the Phytec PCM970 evaluation board The Phytec phyCORE-i.MX27 CPU module is delivered with the PCM970 baseboard by default. This patch adds support for the hardware. This code is only an empty stub; it is filled up with functionality in a later patch series. Signed-off-by: Juergen Beisert --- include/asm-arm/arch-mxc/board-pcm038.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-mxc/board-pcm038.h b/include/asm-arm/arch-mxc/board-pcm038.h index 300467e8db6..750c62afd90 100644 --- a/include/asm-arm/arch-mxc/board-pcm038.h +++ b/include/asm-arm/arch-mxc/board-pcm038.h @@ -30,7 +30,12 @@ * its own devices, it calls baseboard's init function. * TODO: Add your own baseboard init function and call it from * inside pcm038_init(). + * + * This example here is for the development board. Refer pcm970-baseboard.c */ + +extern void pcm970_baseboard_init(void); + #endif #endif /* __ASM_ARCH_MXC_BOARD_PCM038_H__ */ -- cgit v1.2.3 From 75f10b465af9efd59906e9079ed9cbda7e0f7a43 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 22 May 2008 16:20:18 +0100 Subject: [ARM] 5047/2: Support resetting by asserting GPIO pin This adds support for resetting via assertion of GPIO pin. This e.g. is used on Sharp Zaurus SL-6000. Signed-off-by: Dmitry Baryshkov Acked-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/hardware.h | 5 +++++ include/asm-arm/arch-pxa/system.h | 17 +---------------- 2 files changed, 6 insertions(+), 16 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/hardware.h b/include/asm-arm/arch-pxa/hardware.h index e25558faa5a..5547ec797ad 100644 --- a/include/asm-arm/arch-pxa/hardware.h +++ b/include/asm-arm/arch-pxa/hardware.h @@ -205,6 +205,11 @@ static inline void __deprecated pxa_set_cken(int clock, int enable) */ extern unsigned int get_memclk_frequency_10khz(void); +/* + * register GPIO as reset generator + */ +extern int init_gpio_reset(int gpio); + #endif #if defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI) diff --git a/include/asm-arm/arch-pxa/system.h b/include/asm-arm/arch-pxa/system.h index 9aa6c2e939e..14894ae3fa6 100644 --- a/include/asm-arm/arch-pxa/system.h +++ b/include/asm-arm/arch-pxa/system.h @@ -20,19 +20,4 @@ static inline void arch_idle(void) } -static inline void arch_reset(char mode) -{ - if (cpu_is_pxa2xx()) - RCSR = RCSR_HWR | RCSR_WDR | RCSR_SMR | RCSR_GPR; - - if (mode == 's') { - /* Jump into ROM at address 0 */ - cpu_reset(0); - } else { - /* Initialize the watchdog and let it fire */ - OWER = OWER_WME; - OSSR = OSSR_M3; - OSMR3 = OSCR + 368640; /* ... in 100 ms */ - } -} - +void arch_reset(char mode); -- cgit v1.2.3 From b032fccca80cbbedaa80e5a72a202a43f08aa97e Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 12 Jun 2008 11:42:07 +0100 Subject: [ARM] 5083/2: Tosa: fix IrDA transciver powerup. On tosa the tranciver LED isn't powered down if the GPIO47 (STUART_TX) isn't configured as low-level. Power it down if IrDA is off to save a bit of power. Signed-off-by: Dmitry Baryshkov Signed-off-by: Russell King --- include/asm-arm/arch-pxa/tosa.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/tosa.h b/include/asm-arm/arch-pxa/tosa.h index c5b6fde6907..18822621615 100644 --- a/include/asm-arm/arch-pxa/tosa.h +++ b/include/asm-arm/arch-pxa/tosa.h @@ -99,6 +99,7 @@ #define TOSA_GPIO_TP_INT (32) /* Touch Panel pen down interrupt */ #define TOSA_GPIO_JC_CF_IRQ (36) /* CF slot1 Ready */ #define TOSA_GPIO_BAT_LOCKED (38) /* Battery locked */ +#define TOSA_GPIO_IRDA_TX (47) #define TOSA_GPIO_TG_SPI_SCLK (81) #define TOSA_GPIO_TG_SPI_CS (82) #define TOSA_GPIO_TG_SPI_MOSI (83) -- cgit v1.2.3 From bf0116e54e185fd63025f2b975f0f1616ffe41f1 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 14 Jun 2008 11:42:02 +0100 Subject: [ARM] 5097/1: Tosa: support TC6393XB device Add definitions for Toshiba TC6393XB companion chip and register the tc6393xb device. Signed-off-by: Dmitry Baryshkov Signed-off-by: Russell King --- include/asm-arm/arch-pxa/irqs.h | 1 + include/asm-arm/arch-pxa/tosa.h | 44 ++++++++++++++++++++++++++++------------- 2 files changed, 31 insertions(+), 14 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/irqs.h b/include/asm-arm/arch-pxa/irqs.h index b6c8fe37768..fa05e76f64e 100644 --- a/include/asm-arm/arch-pxa/irqs.h +++ b/include/asm-arm/arch-pxa/irqs.h @@ -180,6 +180,7 @@ #define NR_IRQS (IRQ_LOCOMO_SPI_TEND + 1) #elif defined(CONFIG_ARCH_LUBBOCK) || \ defined(CONFIG_MACH_LOGICPD_PXA270) || \ + defined(CONFIG_MACH_TOSA) || \ defined(CONFIG_MACH_MAINSTONE) || \ defined(CONFIG_MACH_PCM027) || \ defined(CONFIG_MACH_MAGICIAN) diff --git a/include/asm-arm/arch-pxa/tosa.h b/include/asm-arm/arch-pxa/tosa.h index 18822621615..a16c103b725 100644 --- a/include/asm-arm/arch-pxa/tosa.h +++ b/include/asm-arm/arch-pxa/tosa.h @@ -25,7 +25,7 @@ */ #define TOSA_SCOOP_GPIO_BASE NR_BUILTIN_GPIO #define TOSA_SCOOP_PXA_VCORE1 SCOOP_GPCR_PA11 -#define TOSA_SCOOP_TC6393_REST_IN SCOOP_GPCR_PA12 +#define TOSA_GPIO_TC6393XB_REST_IN (TOSA_SCOOP_GPIO_BASE + 1) #define TOSA_GPIO_IR_POWERDWN (TOSA_SCOOP_GPIO_BASE + 2) #define TOSA_GPIO_SD_WP (TOSA_SCOOP_GPIO_BASE + 3) #define TOSA_GPIO_PWR_ON (TOSA_SCOOP_GPIO_BASE + 4) @@ -35,11 +35,9 @@ #define TOSA_SCOOP_AC_IN_OL SCOOP_GPCR_PA19 /* GPIO Direction 1 : output mode / 0:input mode */ -#define TOSA_SCOOP_IO_DIR ( TOSA_SCOOP_PXA_VCORE1 | TOSA_SCOOP_TC6393_REST_IN | \ +#define TOSA_SCOOP_IO_DIR (TOSA_SCOOP_PXA_VCORE1 | \ TOSA_SCOOP_AUD_PWR_ON |\ - TOSA_SCOOP_BT_RESET | TOSA_SCOOP_BT_PWR_EN ) -/* GPIO out put level when init 1: Hi */ -#define TOSA_SCOOP_IO_OUT ( TOSA_SCOOP_TC6393_REST_IN ) + TOSA_SCOOP_BT_RESET | TOSA_SCOOP_BT_PWR_EN) /* * SCOOP2 jacket GPIOs @@ -49,16 +47,34 @@ #define TOSA_GPIO_NOTE_LED (TOSA_SCOOP_JC_GPIO_BASE + 1) #define TOSA_GPIO_CHRG_ERR_LED (TOSA_SCOOP_JC_GPIO_BASE + 2) #define TOSA_GPIO_USB_PULLUP (TOSA_SCOOP_JC_GPIO_BASE + 3) -#define TOSA_SCOOP_JC_TC6393_SUSPEND SCOOP_GPCR_PA15 -#define TOSA_SCOOP_JC_TC3693_L3V_ON SCOOP_GPCR_PA16 +#define TOSA_GPIO_TC6393XB_SUSPEND (TOSA_SCOOP_JC_GPIO_BASE + 4) +#define TOSA_GPIO_TC6393XB_L3V_ON (TOSA_SCOOP_JC_GPIO_BASE + 5) #define TOSA_SCOOP_JC_WLAN_DETECT SCOOP_GPCR_PA17 #define TOSA_GPIO_WLAN_LED (TOSA_SCOOP_JC_GPIO_BASE + 7) #define TOSA_SCOOP_JC_CARD_LIMIT_SEL SCOOP_GPCR_PA19 /* GPIO Direction 1 : output mode / 0:input mode */ -#define TOSA_SCOOP_JC_IO_DIR ( \ - TOSA_SCOOP_JC_TC6393_SUSPEND | TOSA_SCOOP_JC_TC3693_L3V_ON | \ - TOSA_SCOOP_JC_CARD_LIMIT_SEL ) +#define TOSA_SCOOP_JC_IO_DIR (TOSA_SCOOP_JC_CARD_LIMIT_SEL) + +/* + * TC6393XB GPIOs + */ +#define TOSA_TC6393XB_GPIO_BASE (NR_BUILTIN_GPIO + 2 * 12) +#define TOSA_TC6393XB_GPIO(i) (TOSA_TC6393XB_GPIO_BASE + (i)) +#define TOSA_TC6393XB_GPIO_BIT(gpio) (1 << (gpio - TOSA_TC6393XB_GPIO_BASE)) + +#define TOSA_GPIO_TG_ON (TOSA_TC6393XB_GPIO_BASE + 0) +#define TOSA_GPIO_L_MUTE (TOSA_TC6393XB_GPIO_BASE + 1) +#define TOSA_GPIO_BL_C20MA (TOSA_TC6393XB_GPIO_BASE + 3) +#define TOSA_GPIO_CARD_VCC_ON (TOSA_TC6393XB_GPIO_BASE + 4) +#define TOSA_GPIO_CHARGE_OFF (TOSA_TC6393XB_GPIO_BASE + 6) +#define TOSA_GPIO_CHARGE_OFF_JC (TOSA_TC6393XB_GPIO_BASE + 7) +#define TOSA_GPIO_BAT0_V_ON (TOSA_TC6393XB_GPIO_BASE + 9) +#define TOSA_GPIO_BAT1_V_ON (TOSA_TC6393XB_GPIO_BASE + 10) +#define TOSA_GPIO_BU_CHRG_ON (TOSA_TC6393XB_GPIO_BASE + 11) +#define TOSA_GPIO_BAT_SW_ON (TOSA_TC6393XB_GPIO_BASE + 12) +#define TOSA_GPIO_BAT0_TH_ON (TOSA_TC6393XB_GPIO_BASE + 14) +#define TOSA_GPIO_BAT1_TH_ON (TOSA_TC6393XB_GPIO_BASE + 15) /* * Timing Generator @@ -84,13 +100,13 @@ #define TOSA_GPIO_JACKET_DETECT (7) #define TOSA_GPIO_nSD_DETECT (9) #define TOSA_GPIO_nSD_INT (10) -#define TOSA_GPIO_TC6393_CLK (11) +#define TOSA_GPIO_TC6393XB_CLK (11) #define TOSA_GPIO_BAT1_CRG (12) #define TOSA_GPIO_CF_CD (13) #define TOSA_GPIO_BAT0_CRG (14) -#define TOSA_GPIO_TC6393_INT (15) +#define TOSA_GPIO_TC6393XB_INT (15) #define TOSA_GPIO_BAT0_LOW (17) -#define TOSA_GPIO_TC6393_RDY (18) +#define TOSA_GPIO_TC6393XB_RDY (18) #define TOSA_GPIO_ON_RESET (19) #define TOSA_GPIO_EAR_IN (20) #define TOSA_GPIO_CF_IRQ (21) /* CF slot0 Ready */ @@ -138,7 +154,7 @@ #define TOSA_IRQ_GPIO_BAT1_CRG IRQ_GPIO(TOSA_GPIO_BAT1_CRG) #define TOSA_IRQ_GPIO_CF_CD IRQ_GPIO(TOSA_GPIO_CF_CD) #define TOSA_IRQ_GPIO_BAT0_CRG IRQ_GPIO(TOSA_GPIO_BAT0_CRG) -#define TOSA_IRQ_GPIO_TC6393_INT IRQ_GPIO(TOSA_GPIO_TC6393_INT) +#define TOSA_IRQ_GPIO_TC6393XB_INT IRQ_GPIO(TOSA_GPIO_TC6393XB_INT) #define TOSA_IRQ_GPIO_BAT0_LOW IRQ_GPIO(TOSA_GPIO_BAT0_LOW) #define TOSA_IRQ_GPIO_EAR_IN IRQ_GPIO(TOSA_GPIO_EAR_IN) #define TOSA_IRQ_GPIO_CF_IRQ IRQ_GPIO(TOSA_GPIO_CF_IRQ) -- cgit v1.2.3 From 16b32fd0a35b30cbd67395cfcbd360354db44f39 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 5 Jul 2008 09:02:48 +0100 Subject: [ARM] 5150/1: Tosa: support built-in bluetooth power-up The driver is pretty much generic and will be later shared with a few other devices, like hx4700 ipaq. Signed-off-by: Dmitry Baryshkov Signed-off-by: Russell King --- include/asm-arm/arch-pxa/tosa.h | 7 +++---- include/asm-arm/arch-pxa/tosa_bt.h | 22 ++++++++++++++++++++++ 2 files changed, 25 insertions(+), 4 deletions(-) create mode 100644 include/asm-arm/arch-pxa/tosa_bt.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/tosa.h b/include/asm-arm/arch-pxa/tosa.h index a16c103b725..a72803f0461 100644 --- a/include/asm-arm/arch-pxa/tosa.h +++ b/include/asm-arm/arch-pxa/tosa.h @@ -30,14 +30,13 @@ #define TOSA_GPIO_SD_WP (TOSA_SCOOP_GPIO_BASE + 3) #define TOSA_GPIO_PWR_ON (TOSA_SCOOP_GPIO_BASE + 4) #define TOSA_SCOOP_AUD_PWR_ON SCOOP_GPCR_PA16 -#define TOSA_SCOOP_BT_RESET SCOOP_GPCR_PA17 -#define TOSA_SCOOP_BT_PWR_EN SCOOP_GPCR_PA18 +#define TOSA_GPIO_BT_RESET (TOSA_SCOOP_GPIO_BASE + 6) +#define TOSA_GPIO_BT_PWR_EN (TOSA_SCOOP_GPIO_BASE + 7) #define TOSA_SCOOP_AC_IN_OL SCOOP_GPCR_PA19 /* GPIO Direction 1 : output mode / 0:input mode */ #define TOSA_SCOOP_IO_DIR (TOSA_SCOOP_PXA_VCORE1 | \ - TOSA_SCOOP_AUD_PWR_ON |\ - TOSA_SCOOP_BT_RESET | TOSA_SCOOP_BT_PWR_EN) + TOSA_SCOOP_AUD_PWR_ON) /* * SCOOP2 jacket GPIOs diff --git a/include/asm-arm/arch-pxa/tosa_bt.h b/include/asm-arm/arch-pxa/tosa_bt.h new file mode 100644 index 00000000000..efc3c3d3b75 --- /dev/null +++ b/include/asm-arm/arch-pxa/tosa_bt.h @@ -0,0 +1,22 @@ +/* + * Tosa bluetooth built-in chip control. + * + * Later it may be shared with some other platforms. + * + * Copyright (c) 2008 Dmitry Baryshkov + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#ifndef TOSA_BT_H +#define TOSA_BT_H + +struct tosa_bt_data { + int gpio_pwr; + int gpio_reset; +}; + +#endif + -- cgit v1.2.3 From 5e329d1c7f5fe6adfee99c783fa98bda7dae8ac5 Mon Sep 17 00:00:00 2001 From: Stefan Schmidt Date: Fri, 6 Jun 2008 10:12:37 +0100 Subject: [ARM] 5079/1: Warn people when using pxa2xx-gpio.h Warn people when using pxa2xx-gpio.h as it is only here for backwards compatibility. The new mfp-pxa2[57]x.h and the relevant API should be used instead. Signed-off-by: Stefan Schmidt Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa2xx-gpio.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxa2xx-gpio.h b/include/asm-arm/arch-pxa/pxa2xx-gpio.h index 763313c5e6b..a6e60f69161 100644 --- a/include/asm-arm/arch-pxa/pxa2xx-gpio.h +++ b/include/asm-arm/arch-pxa/pxa2xx-gpio.h @@ -1,6 +1,8 @@ #ifndef __ASM_ARCH_PXA2XX_GPIO_H #define __ASM_ARCH_PXA2XX_GPIO_H +#warning Please use mfp-pxa2[57]x.h instead of pxa2xx-gpio.h + /* GPIO alternate function assignments */ #define GPIO1_RST 1 /* reset */ -- cgit v1.2.3 From ff7b04796d9866327ea76e1393f1e902ef032f84 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Tue, 8 Jul 2008 11:58:36 -0700 Subject: dmaengine: DMA engine driver for Marvell XOR engine The XOR engine found in Marvell's SoCs and system controllers provides XOR and DMA operation, iSCSI CRC32C calculation, memory initialization, and memory ECC error cleanup operation support. This driver implements the DMA engine API and supports the following capabilities: - memcpy - xor - memset The XOR engine can be used by DMA engine clients implemented in the kernel, one of those clients is the RAID module. In that case, I observed 20% improvement in the raid5 write throughput, and 40% decrease in the CPU utilization when doing array construction, those results obtained on an 5182 running at 500Mhz. When enabling the NET DMA client, the performance decreased, so meanwhile it is recommended to keep this client off. Signed-off-by: Saeed Bishara Signed-off-by: Lennert Buytenhek Signed-off-by: Nicolas Pitre Acked-by: Maciej Sosnowski Signed-off-by: Dan Williams --- include/asm-arm/plat-orion/mv_xor.h | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) create mode 100644 include/asm-arm/plat-orion/mv_xor.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-orion/mv_xor.h b/include/asm-arm/plat-orion/mv_xor.h new file mode 100644 index 00000000000..c349e8ff5cc --- /dev/null +++ b/include/asm-arm/plat-orion/mv_xor.h @@ -0,0 +1,28 @@ +/* + * Marvell XOR platform device data definition file. + */ + +#ifndef __ASM_PLAT_ORION_MV_XOR_H +#define __ASM_PLAT_ORION_MV_XOR_H + +#include +#include + +#define MV_XOR_SHARED_NAME "mv_xor_shared" +#define MV_XOR_NAME "mv_xor" + +struct mbus_dram_target_info; + +struct mv_xor_platform_shared_data { + struct mbus_dram_target_info *dram; +}; + +struct mv_xor_platform_data { + struct platform_device *shared; + int hw_id; + dma_cap_mask_t cap_mask; + size_t pool_size; +}; + + +#endif -- cgit v1.2.3 From 66a7f72d9892013e9ea663260f407758989ff510 Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 2 Jun 2008 16:10:20 +0100 Subject: [ARM] pxa: remove pxa_set_cken() pxa_set_cken() is now unused, remove it. Signed-off-by: Russell King --- include/asm-arm/arch-pxa/hardware.h | 9 --------- 1 file changed, 9 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/hardware.h b/include/asm-arm/arch-pxa/hardware.h index e25558faa5a..d9af6dabc89 100644 --- a/include/asm-arm/arch-pxa/hardware.h +++ b/include/asm-arm/arch-pxa/hardware.h @@ -191,15 +191,6 @@ extern int pxa_gpio_get_value(unsigned gpio); */ extern void pxa_gpio_set_value(unsigned gpio, int value); -/* - * Routine to enable or disable CKEN - */ -static inline void __deprecated pxa_set_cken(int clock, int enable) -{ - extern void __pxa_set_cken(int clock, int enable); - __pxa_set_cken(clock, enable); -} - /* * return current memory and LCD clock frequency in units of 10kHz */ -- cgit v1.2.3 From 918dbcba4ee3f0ad7d617b3969d5016481b9ceff Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Wed, 2 Jul 2008 13:53:45 +0100 Subject: [ARM] 5145/1: PXA2xx: provide api to control IrDA pins state Provide a set of functions to control state of pins dedicated to IrDA. Signed-off-by: Dmitry Baryshkov Signed-off-by: Russell King --- include/asm-arm/arch-pxa/irda.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/irda.h b/include/asm-arm/arch-pxa/irda.h index 99f4f423a8e..0a50c3c763d 100644 --- a/include/asm-arm/arch-pxa/irda.h +++ b/include/asm-arm/arch-pxa/irda.h @@ -16,4 +16,8 @@ struct pxaficp_platform_data { extern void pxa_set_ficp_info(struct pxaficp_platform_data *info); +#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x) +void pxa2xx_transceiver_mode(struct device *dev, int mode); +#endif + #endif -- cgit v1.2.3 From 9f19d6382854d6b2d58cc364253779479e14facc Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Tue, 10 Jun 2008 12:30:05 +0100 Subject: [ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit As well as moving all the device declarations to a single one in devices.c this causes all platforms to register the I/O and interrupt resources for the AC97 controller. Cc: eric miao Cc: Mike Rapoport Cc: Lennert Buytenhek Cc: Jürgen Schindele Cc: Juergen Beisert Signed-off-by: Mark Brown Signed-off-by: Russell King --- include/asm-arm/arch-pxa/audio.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/audio.h b/include/asm-arm/arch-pxa/audio.h index 52bbe3bc25e..f82f96dd105 100644 --- a/include/asm-arm/arch-pxa/audio.h +++ b/include/asm-arm/arch-pxa/audio.h @@ -12,4 +12,6 @@ typedef struct { void *priv; } pxa2xx_audio_ops_t; +extern void pxa_set_ac97_info(pxa2xx_audio_ops_t *ops); + #endif -- cgit v1.2.3 From e172274ccc55d20536fbdceb6131f38e288541e0 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Fri, 13 Jun 2008 09:17:31 +0100 Subject: [ARM] 5088/3: pxa2xx: add pxa2xx_set_spi_info to register pxa2xx-spi platform devices Add a function to dynamically allocate and register pxa2xx-spi platform devices, to be used by PXA2xx and PXA3xx based systems. Switch pcm027 and lubbock to use it. Signed-off-by: Guennadi Liakhovetski Acked-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa2xx_spi.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxa2xx_spi.h b/include/asm-arm/arch-pxa/pxa2xx_spi.h index 3459fb26ce9..2206cb61a9f 100644 --- a/include/asm-arm/arch-pxa/pxa2xx_spi.h +++ b/include/asm-arm/arch-pxa/pxa2xx_spi.h @@ -41,4 +41,6 @@ struct pxa2xx_spi_chip { void (*cs_control)(u32 command); }; +extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info); + #endif /*PXA2XX_SPI_H_*/ -- cgit v1.2.3 From 839257c9a818c81a802fdd705602589355571662 Mon Sep 17 00:00:00 2001 From: Mike Rapoport Date: Tue, 17 Jun 2008 09:49:27 +0100 Subject: [ARM] 5106/1: CM-X270: remove unneeded cm-x270.h The include/asm-arm/arch-pxa/cm-x270.h is not used anymore. Remove it. Signed-off-by: Mike Rapoport Signed-off-by: Russell King --- include/asm-arm/arch-pxa/cm-x270.h | 50 -------------------------------------- 1 file changed, 50 deletions(-) delete mode 100644 include/asm-arm/arch-pxa/cm-x270.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/cm-x270.h b/include/asm-arm/arch-pxa/cm-x270.h deleted file mode 100644 index f8fac9e1800..00000000000 --- a/include/asm-arm/arch-pxa/cm-x270.h +++ /dev/null @@ -1,50 +0,0 @@ -/* - * linux/include/asm/arch-pxa/cm-x270.h - * - * Copyright Compulab Ltd., 2003, 2007 - * Mike Rapoport - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - - -/* CM-x270 device physical addresses */ -#define CMX270_CS1_PHYS (PXA_CS1_PHYS) -#define MARATHON_PHYS (PXA_CS2_PHYS) -#define CMX270_IDE104_PHYS (PXA_CS3_PHYS) -#define CMX270_IT8152_PHYS (PXA_CS4_PHYS) - -/* Statically mapped regions */ -#define CMX270_VIRT_BASE (0xe8000000) -#define CMX270_IT8152_VIRT (CMX270_VIRT_BASE) -#define CMX270_IDE104_VIRT (CMX270_IT8152_VIRT + SZ_64M) - -/* GPIO related definitions */ -#define GPIO_IT8152_IRQ (22) - -#define IRQ_GPIO_IT8152_IRQ IRQ_GPIO(GPIO_IT8152_IRQ) -#define PME_IRQ IRQ_GPIO(0) -#define CMX270_IDE_IRQ IRQ_GPIO(100) -#define CMX270_GPIRQ1 IRQ_GPIO(101) -#define CMX270_TOUCHIRQ IRQ_GPIO(96) -#define CMX270_ETHIRQ IRQ_GPIO(10) -#define CMX270_GFXIRQ IRQ_GPIO(95) -#define CMX270_NANDIRQ IRQ_GPIO(89) -#define CMX270_MMC_IRQ IRQ_GPIO(83) - -/* PCMCIA related definitions */ -#define PCC_DETECT(x) (GPLR(84 - (x)) & GPIO_bit(84 - (x))) -#define PCC_READY(x) (GPLR(82 - (x)) & GPIO_bit(82 - (x))) - -#define PCMCIA_S0_CD_VALID IRQ_GPIO(84) -#define PCMCIA_S0_CD_VALID_EDGE GPIO_BOTH_EDGES - -#define PCMCIA_S1_CD_VALID IRQ_GPIO(83) -#define PCMCIA_S1_CD_VALID_EDGE GPIO_BOTH_EDGES - -#define PCMCIA_S0_RDYINT IRQ_GPIO(82) -#define PCMCIA_S1_RDYINT IRQ_GPIO(81) - -#define PCMCIA_RESET_GPIO 53 -- cgit v1.2.3 From 6d3dfe4a3141476a3cf59ce6d2d1c25f9b5cfae8 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Mon, 2 Jun 2008 15:58:03 +0800 Subject: [ARM] pxa: allow display of uncompress message through STUART Some boards use UART other than FFUART for the console, E.g. Marvell PXA3xx Form Factor Platform (aka Littleton) uses STUART. This patch modifies the uncompress.h so that display of the uncompress message is routed to the STUART. Signed-off-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/uncompress.h | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/uncompress.h b/include/asm-arm/arch-pxa/uncompress.h index dadf4c20b62..f4551269aaf 100644 --- a/include/asm-arm/arch-pxa/uncompress.h +++ b/include/asm-arm/arch-pxa/uncompress.h @@ -11,11 +11,11 @@ #include #include +#include -#define __REG(x) ((volatile unsigned long *)x) - -#define UART FFUART +#define __REG(x) ((volatile unsigned long *)x) +static volatile unsigned long *UART = FFUART; static inline void putc(char c) { @@ -33,8 +33,13 @@ static inline void flush(void) { } +static inline void arch_decomp_setup(void) +{ + if (machine_is_littleton()) + UART = STUART; +} + /* * nothing to do */ -#define arch_decomp_setup() #define arch_decomp_wdog() -- cgit v1.2.3 From 566b450c33ea43f339d54d445f4ea1ab2e021909 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Mon, 16 Jun 2008 09:47:47 +0800 Subject: [ARM] pxa: add pxa2xx_mfp_set_lpm() to facilitate low power state change Some boards want to change low power state of pins on-the-fly, this function helps to facilitate that operation instead of switching back-n-forth between two configurations with pxa2xx_mfp_config(). Signed-off-by: Eric Miao Tested-by: Robert Jarzmik Signed-off-by: Russell King --- include/asm-arm/arch-pxa/mfp-pxa2xx.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/mfp-pxa2xx.h b/include/asm-arm/arch-pxa/mfp-pxa2xx.h index db8d890d237..8de1c0dae62 100644 --- a/include/asm-arm/arch-pxa/mfp-pxa2xx.h +++ b/include/asm-arm/arch-pxa/mfp-pxa2xx.h @@ -128,5 +128,6 @@ #define GPIO84_GPIO MFP_CFG_IN(GPIO84, AF0) extern void pxa2xx_mfp_config(unsigned long *mfp_cfgs, int num); +extern void pxa2xx_mfp_set_lpm(int mfp, unsigned long lpm); extern int gpio_set_wake(unsigned int gpio, unsigned int on); #endif /* __ASM_ARCH_MFP_PXA2XX_H */ -- cgit v1.2.3 From 9ae819a819b4dfc60ac13dd1f1e1a7eaa3d4a6cb Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Mon, 2 Jun 2008 15:22:03 +0800 Subject: [ARM] pxa: add pxa3xx NAND device and clock sources A pxa3xx_set_nand_info() is also introduced to set the PXA3xx NAND driver specific platform_data structure pointer. Signed-off-by: Eric Miao Cc: Sergey Podstavin Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa3xx_nand.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxa3xx_nand.h b/include/asm-arm/arch-pxa/pxa3xx_nand.h index 81a8937486c..eb4b190b665 100644 --- a/include/asm-arm/arch-pxa/pxa3xx_nand.h +++ b/include/asm-arm/arch-pxa/pxa3xx_nand.h @@ -15,4 +15,6 @@ struct pxa3xx_nand_platform_data { struct mtd_partition *parts; unsigned int nr_parts; }; + +extern void pxa3xx_set_nand_info(struct pxa3xx_nand_platform_data *info); #endif /* __ASM_ARCH_PXA3XX_NAND_H */ -- cgit v1.2.3 From a1f7fc48c143537e2bf70affee7e8932f5be9bb4 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 28 May 2008 10:44:16 +0800 Subject: [ARM] pxa: add GPIO expander (PCA9539) support for zylonite And also reserve 32 IRQs for the two GPIO expanders. Signed-off-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/irqs.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/irqs.h b/include/asm-arm/arch-pxa/irqs.h index b6c8fe37768..d8573604846 100644 --- a/include/asm-arm/arch-pxa/irqs.h +++ b/include/asm-arm/arch-pxa/irqs.h @@ -184,6 +184,8 @@ defined(CONFIG_MACH_PCM027) || \ defined(CONFIG_MACH_MAGICIAN) #define NR_IRQS (IRQ_BOARD_END) +#elif defined(CONFIG_MACH_ZYLONITE) +#define NR_IRQS (IRQ_BOARD_START + 32) #else #define NR_IRQS (IRQ_BOARD_START) #endif -- cgit v1.2.3 From 5c9f50e90e8056fb5a8bdd479ab0591d5dad79a0 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Tue, 17 Jun 2008 19:03:54 +0800 Subject: [ARM] pxa: add simple gpio debug LEDs support for zylonite Signed-off-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/zylonite.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/zylonite.h b/include/asm-arm/arch-pxa/zylonite.h index de577de8d18..0d35ca04731 100644 --- a/include/asm-arm/arch-pxa/zylonite.h +++ b/include/asm-arm/arch-pxa/zylonite.h @@ -16,6 +16,8 @@ struct platform_mmc_slot { extern struct platform_mmc_slot zylonite_mmc_slot[]; extern int gpio_eth_irq; +extern int gpio_debug_led1; +extern int gpio_debug_led2; extern int wm9713_irq; -- cgit v1.2.3 From 63f385cd1f649b3f4f2d59fc609e051981215fd7 Mon Sep 17 00:00:00 2001 From: Arnaud Patard Date: Tue, 8 Jul 2008 23:07:48 +0100 Subject: [ARM] 5160/1: IOP3XX: gpio/gpiolib support This patch brings support for gpio/gpiolib framework to Intel IOP3xx platforms. Signed-off-by: Arnaud Patard Acked-by: Dan Williams Signed-off-by: Russell King --- include/asm-arm/arch-iop32x/gpio.h | 6 +++ include/asm-arm/arch-iop33x/gpio.h | 6 +++ include/asm-arm/hardware/iop3xx-gpio.h | 73 ++++++++++++++++++++++++++++++++++ 3 files changed, 85 insertions(+) create mode 100644 include/asm-arm/arch-iop32x/gpio.h create mode 100644 include/asm-arm/arch-iop33x/gpio.h create mode 100644 include/asm-arm/hardware/iop3xx-gpio.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-iop32x/gpio.h b/include/asm-arm/arch-iop32x/gpio.h new file mode 100644 index 00000000000..708f4ec9db1 --- /dev/null +++ b/include/asm-arm/arch-iop32x/gpio.h @@ -0,0 +1,6 @@ +#ifndef __ASM_ARCH_IOP32X_GPIO_H +#define __ASM_ARCH_IOP32X_GPIO_H + +#include + +#endif diff --git a/include/asm-arm/arch-iop33x/gpio.h b/include/asm-arm/arch-iop33x/gpio.h new file mode 100644 index 00000000000..ddd55bba9bb --- /dev/null +++ b/include/asm-arm/arch-iop33x/gpio.h @@ -0,0 +1,6 @@ +#ifndef __ASM_ARCH_IOP33X_GPIO_H +#define __ASM_ARCH_IOP33X_GPIO_H + +#include + +#endif diff --git a/include/asm-arm/hardware/iop3xx-gpio.h b/include/asm-arm/hardware/iop3xx-gpio.h new file mode 100644 index 00000000000..0c9331f9ac2 --- /dev/null +++ b/include/asm-arm/hardware/iop3xx-gpio.h @@ -0,0 +1,73 @@ +/* + * linux/include/asm-arm/hardware/iop3xx-gpio.h + * + * IOP3xx GPIO wrappers + * + * Copyright (c) 2008 Arnaud Patard + * Based on IXP4XX gpio.h file + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#ifndef __ASM_ARM_HARDWARE_IOP3XX_GPIO_H +#define __ASM_ARM_HARDWARE_IOP3XX_GPIO_H + +#include +#include + +#define IOP3XX_N_GPIOS 8 + +static inline int gpio_get_value(unsigned gpio) +{ + if (gpio > IOP3XX_N_GPIOS) + return __gpio_get_value(gpio); + + return gpio_line_get(gpio); +} + +static inline void gpio_set_value(unsigned gpio, int value) +{ + if (gpio > IOP3XX_N_GPIOS) { + __gpio_set_value(gpio, value); + return; + } + gpio_line_set(gpio, value); +} + +static inline int gpio_cansleep(unsigned gpio) +{ + if (gpio < IOP3XX_N_GPIOS) + return 0; + else + return __gpio_cansleep(gpio); +} + +/* + * The GPIOs are not generating any interrupt + * Note : manuals are not clear about this + */ +static inline int gpio_to_irq(int gpio) +{ + return -EINVAL; +} + +static inline int irq_to_gpio(int gpio) +{ + return -EINVAL; +} + +#endif + -- cgit v1.2.3 From aa9ae8eb1a917c8794bceef0a8e6ff1f4d7c46de Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Wed, 25 Jun 2008 22:17:16 +0100 Subject: Fix serial broken-ness on PXA250 PXA255 and 26x are the only PXA CPUs with HWUART. This patch prevents bogus initialisation on other models. Signed-off-by: Ian Molton --- include/asm-arm/arch-pxa/hardware.h | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/hardware.h b/include/asm-arm/arch-pxa/hardware.h index d9af6dabc89..b6a8317c2ec 100644 --- a/include/asm-arm/arch-pxa/hardware.h +++ b/include/asm-arm/arch-pxa/hardware.h @@ -69,6 +69,12 @@ _id == 0x212; \ }) +#define __cpu_is_pxa255(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x2d0; \ + }) + #define __cpu_is_pxa25x(id) \ ({ \ unsigned int _id = (id) >> 4 & 0xfff; \ @@ -76,6 +82,7 @@ }) #else #define __cpu_is_pxa21x(id) (0) +#define __cpu_is_pxa255(id) (0) #define __cpu_is_pxa25x(id) (0) #endif @@ -124,6 +131,11 @@ __cpu_is_pxa21x(read_cpuid_id()); \ }) +#define cpu_is_pxa255() \ + ({ \ + __cpu_is_pxa255(read_cpuid_id()); \ + }) + #define cpu_is_pxa25x() \ ({ \ __cpu_is_pxa25x(read_cpuid_id()); \ -- cgit v1.2.3 From 613526677a74c2b3d1b1696ea7334b2cf35155b3 Mon Sep 17 00:00:00 2001 From: sedji gaouaou Date: Thu, 10 Jul 2008 10:15:35 +0100 Subject: [ARM] 5130/4: Support for the at91sam9g20 Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC. AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. We created a new board for this device but based the chip support directly on 9260 files with little updates. Here is the chip page on Atmel wabsite: http://atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Sedji Gaouaou Signed-off-by: Justin Waters Acked-by: Andrew Victor Signed-off-by: Russell King --- include/asm-arm/arch-at91/at91sam9260.h | 11 +++++++++++ include/asm-arm/arch-at91/board.h | 2 +- include/asm-arm/arch-at91/cpu.h | 7 +++++++ include/asm-arm/arch-at91/hardware.h | 2 +- include/asm-arm/arch-at91/timex.h | 5 +++++ 5 files changed, 25 insertions(+), 2 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-at91/at91sam9260.h b/include/asm-arm/arch-at91/at91sam9260.h index c8934fe34dc..889872a3f2a 100644 --- a/include/asm-arm/arch-at91/at91sam9260.h +++ b/include/asm-arm/arch-at91/at91sam9260.h @@ -6,6 +6,8 @@ * Common definitions. * Based on AT91SAM9260 datasheet revision A (Preliminary). * + * Includes also definitions for AT91SAM9XE and AT91SAM9G families + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -123,5 +125,14 @@ #define AT91SAM9XE_FLASH_BASE 0x00200000 /* Internal FLASH base address */ #define AT91SAM9XE_SRAM_BASE 0x00300000 /* Internal SRAM base address */ +#define AT91SAM9G20_ROM_BASE 0x00100000 /* Internal ROM base address */ +#define AT91SAM9G20_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ + +#define AT91SAM9G20_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */ +#define AT91SAM9G20_SRAM0_SIZE SZ_16K /* Internal SRAM 0 size (16Kb) */ +#define AT91SAM9G20_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */ +#define AT91SAM9G20_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */ + +#define AT91SAM9G20_UHP_BASE 0x00500000 /* USB Host controller */ #endif diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h index 1f247028686..94de788da76 100644 --- a/include/asm-arm/arch-at91/board.h +++ b/include/asm-arm/arch-at91/board.h @@ -77,7 +77,7 @@ struct at91_eth_data { }; extern void __init at91_add_device_eth(struct at91_eth_data *data); -#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9) +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) #define eth_platform_data at91_eth_data #endif diff --git a/include/asm-arm/arch-at91/cpu.h b/include/asm-arm/arch-at91/cpu.h index 7145166826a..52df794205c 100644 --- a/include/asm-arm/arch-at91/cpu.h +++ b/include/asm-arm/arch-at91/cpu.h @@ -21,6 +21,7 @@ #define ARCH_ID_AT91SAM9260 0x019803a0 #define ARCH_ID_AT91SAM9261 0x019703a0 #define ARCH_ID_AT91SAM9263 0x019607a0 +#define ARCH_ID_AT91SAM9G20 0x019905a0 #define ARCH_ID_AT91SAM9RL64 0x019b03a0 #define ARCH_ID_AT91CAP9 0x039A03A0 @@ -63,6 +64,12 @@ static inline unsigned long at91_arch_identify(void) #define cpu_is_at91sam9260() (0) #endif +#ifdef CONFIG_ARCH_AT91SAM9G20 +#define cpu_is_at91sam9g20() (at91_cpu_identify() == ARCH_ID_AT91SAM9G20) +#else +#define cpu_is_at91sam9g20() (0) +#endif + #ifdef CONFIG_ARCH_AT91SAM9261 #define cpu_is_at91sam9261() (at91_cpu_identify() == ARCH_ID_AT91SAM9261) #else diff --git a/include/asm-arm/arch-at91/hardware.h b/include/asm-arm/arch-at91/hardware.h index 2c826d8247a..016a3a3f663 100644 --- a/include/asm-arm/arch-at91/hardware.h +++ b/include/asm-arm/arch-at91/hardware.h @@ -18,7 +18,7 @@ #if defined(CONFIG_ARCH_AT91RM9200) #include -#elif defined(CONFIG_ARCH_AT91SAM9260) +#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) #include #elif defined(CONFIG_ARCH_AT91SAM9261) #include diff --git a/include/asm-arm/arch-at91/timex.h b/include/asm-arm/arch-at91/timex.h index 6e084eb839d..298d8313cda 100644 --- a/include/asm-arm/arch-at91/timex.h +++ b/include/asm-arm/arch-at91/timex.h @@ -57,6 +57,11 @@ #define AT91SAM9_MASTER_CLOCK 100000000 #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) +#elif defined(CONFIG_ARCH_AT91SAM9G20) + +#define AT91SAM9_MASTER_CLOCK 132096000 +#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) + #elif defined(CONFIG_ARCH_AT91CAP9) #define AT91CAP9_MASTER_CLOCK 100000000 -- cgit v1.2.3 From b5e4ad57eeffef0ac274413f83be4ef903719ea4 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Marek=20Va=C5=A1ut?= Date: Mon, 7 Jul 2008 17:25:46 +0100 Subject: [ARM] 5153/1: Add support for PalmTX handheld computer PalmTX is PXA27x based device with wifi, bluetooth, touchscreen, sdio slot, irda, keypad, nand flash, pxa framebuffer, serial and usb gadget interface. Supported by this patch is pxafb, touchscreen, irda, keypad and sdio slot. Signed-off-by: Marek Vasut Signed-off-by: Russell King --- include/asm-arm/arch-pxa/palmtx.h | 106 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 106 insertions(+) create mode 100644 include/asm-arm/arch-pxa/palmtx.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/palmtx.h b/include/asm-arm/arch-pxa/palmtx.h new file mode 100644 index 00000000000..1e8bccbda51 --- /dev/null +++ b/include/asm-arm/arch-pxa/palmtx.h @@ -0,0 +1,106 @@ +/* + * GPIOs and interrupts for Palm T|X Handheld Computer + * + * Based on palmld-gpio.h by Alex Osborne + * + * Authors: Marek Vasut + * Cristiano P. + * Jan Herman <2hp@seznam.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef _INCLUDE_PALMTX_H_ +#define _INCLUDE_PALMTX_H_ + +/** HERE ARE GPIOs **/ + +/* GPIOs */ +#define GPIO_NR_PALMTX_GPIO_RESET 1 + +#define GPIO_NR_PALMTX_POWER_DETECT 12 /* 90 */ +#define GPIO_NR_PALMTX_HOTSYNC_BUTTON_N 10 +#define GPIO_NR_PALMTX_EARPHONE_DETECT 107 + +/* SD/MMC */ +#define GPIO_NR_PALMTX_SD_DETECT_N 14 +#define GPIO_NR_PALMTX_SD_POWER 114 /* probably */ +#define GPIO_NR_PALMTX_SD_READONLY 115 /* probably */ + +/* TOUCHSCREEN */ +#define GPIO_NR_PALMTX_WM9712_IRQ 27 + +/* IRDA - disable GPIO connected to SD pin of tranceiver (TFBS4710?) ? */ +#define GPIO_NR_PALMTX_IR_DISABLE 40 + +/* USB */ +#define GPIO_NR_PALMTX_USB_DETECT_N 13 +#define GPIO_NR_PALMTX_USB_POWER 95 +#define GPIO_NR_PALMTX_USB_PULLUP 93 + +/* LCD/BACKLIGHT */ +#define GPIO_NR_PALMTX_BL_POWER 84 +#define GPIO_NR_PALMTX_LCD_POWER 96 + +/* LCD BORDER */ +#define GPIO_NR_PALMTX_BORDER_SWITCH 98 +#define GPIO_NR_PALMTX_BORDER_SELECT 22 + +/* BLUETOOTH */ +#define GPIO_NR_PALMTX_BT_POWER 17 +#define GPIO_NR_PALMTX_BT_RESET 83 + +/* PCMCIA (WiFi) */ +#define GPIO_NR_PALMTX_PCMCIA_POWER1 94 +#define GPIO_NR_PALMTX_PCMCIA_POWER2 108 +#define GPIO_NR_PALMTX_PCMCIA_RESET 79 +#define GPIO_NR_PALMTX_PCMCIA_READY 116 + +/* NAND Flash ... this GPIO may be incorrect! */ +#define GPIO_NR_PALMTX_NAND_BUFFER_DIR 79 + +/* INTERRUPTS */ +#define IRQ_GPIO_PALMTX_SD_DETECT_N IRQ_GPIO(GPIO_NR_PALMTX_SD_DETECT_N) +#define IRQ_GPIO_PALMTX_WM9712_IRQ IRQ_GPIO(GPIO_NR_PALMTX_WM9712_IRQ) +#define IRQ_GPIO_PALMTX_USB_DETECT IRQ_GPIO(GPIO_NR_PALMTX_USB_DETECT) +#define IRQ_GPIO_PALMTX_GPIO_RESET IRQ_GPIO(GPIO_NR_PALMTX_GPIO_RESET) + +/** HERE ARE INIT VALUES **/ + +/* Various addresses */ +#define PALMTX_PCMCIA_PHYS 0x28000000 +#define PALMTX_PCMCIA_VIRT 0xf0000000 +#define PALMTX_PCMCIA_SIZE 0x100000 + +#define PALMTX_PHYS_RAM_START 0xa0000000 +#define PALMTX_PHYS_IO_START 0x40000000 + +#define PALMTX_PHYS_FLASH_START PXA_CS0_PHYS /* ChipSelect 0 */ +#define PALMTX_PHYS_NAND_START PXA_CS1_PHYS /* ChipSelect 1 */ + +/* TOUCHSCREEN */ +#define AC97_LINK_FRAME 21 + + +/* BATTERY */ +#define PALMTX_BAT_MAX_VOLTAGE 4000 /* 4.00v current voltage */ +#define PALMTX_BAT_MIN_VOLTAGE 3550 /* 3.55v critical voltage */ +#define PALMTX_BAT_MAX_CURRENT 0 /* unknokn */ +#define PALMTX_BAT_MIN_CURRENT 0 /* unknown */ +#define PALMTX_BAT_MAX_CHARGE 1 /* unknown */ +#define PALMTX_BAT_MIN_CHARGE 1 /* unknown */ +#define PALMTX_MAX_LIFE_MINS 360 /* on-life in minutes */ + +#define PALMTX_BAT_MEASURE_DELAY (HZ * 1) + +/* BACKLIGHT */ +#define PALMTX_MAX_INTENSITY 0xFE +#define PALMTX_DEFAULT_INTENSITY 0x7E +#define PALMTX_LIMIT_MASK 0x7F +#define PALMTX_PRESCALER 0x3F +#define PALMTX_PERIOD_NS 3500 + +#endif -- cgit v1.2.3 From 00249adc0ebf9bc5e1b7b53dee37601fd7291396 Mon Sep 17 00:00:00 2001 From: Stefan Schmidt Date: Wed, 9 Jul 2008 08:05:42 +0100 Subject: [ARM] 5165/1: pxafb: More LCCR3 depth defines Add missing depth definitions to LCCR3. Signed-off-by: Daniel Ribeiro Acked-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/regs-lcd.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/regs-lcd.h b/include/asm-arm/arch-pxa/regs-lcd.h index f762493f514..999b2a02ce2 100644 --- a/include/asm-arm/arch-pxa/regs-lcd.h +++ b/include/asm-arm/arch-pxa/regs-lcd.h @@ -24,6 +24,12 @@ #define LCCR3_4BPP (2 << 24) #define LCCR3_8BPP (3 << 24) #define LCCR3_16BPP (4 << 24) +#define LCCR3_18BPP (5 << 24) +#define LCCR3_18BPP_P (6 << 24) +#define LCCR3_19BPP (7 << 24) +#define LCCR3_19BPP_P (1 << 29) +#define LCCR3_24BPP ((1 << 29) | (1 << 24)) +#define LCCR3_25BPP ((1 << 29) | (2 << 24)) #define LCCR3_PDFOR_0 (0 << 30) #define LCCR3_PDFOR_1 (1 << 30) -- cgit v1.2.3 From c1450f156fda8921a55e3f4fe596274278010f31 Mon Sep 17 00:00:00 2001 From: Stefan Schmidt Date: Wed, 9 Jul 2008 08:06:32 +0100 Subject: [ARM] 5164/1: pxafb: Support for RGB666, RGBT666, RGB888 and RGBT888 Add the .depth field to pxafb_mode_info and use it to set pixel data format as 18(RGB666), 19(RGBT666), 24(RGB888) or 25(RGBT888) Signed-off-by: Daniel Ribeiro Acked-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxafb.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxafb.h b/include/asm-arm/arch-pxa/pxafb.h index bbd22396841..daf018d0c60 100644 --- a/include/asm-arm/arch-pxa/pxafb.h +++ b/include/asm-arm/arch-pxa/pxafb.h @@ -71,7 +71,8 @@ struct pxafb_mode_info { u_char bpp; u_int cmap_greyscale:1, - unused:31; + depth:8, + unused:23; /* Parallel Mode Timing */ u_char hsync_len; -- cgit v1.2.3 From 390d452fa1d912b6e76744a34777d7390ab1fa1c Mon Sep 17 00:00:00 2001 From: Stefan Schmidt Date: Wed, 9 Jul 2008 08:07:29 +0100 Subject: [ARM] 5163/1: pxa27x_udc: Allow choosing the bits in UP2OCR_SEOS Allow choosing the bits in UP2OCR_SEOS. Signed-off-by: Daniel Ribeiro Acked-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa27x-udc.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/pxa27x-udc.h b/include/asm-arm/arch-pxa/pxa27x-udc.h index bc1cf7d0773..ab1443f8bd8 100644 --- a/include/asm-arm/arch-pxa/pxa27x-udc.h +++ b/include/asm-arm/arch-pxa/pxa27x-udc.h @@ -97,7 +97,7 @@ #define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */ #define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */ #define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */ -#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */ +#define UP2OCR_SEOS(x) ((x & 7) << 24) /* Single-Ended Output Select */ #define UDCCSN(x) __REG2(0x40600100, (x) << 2) #define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */ -- cgit v1.2.3 From 54b238469bce3a1b5012b2f0ebf261cf1c53e664 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Thu, 19 Jun 2008 03:11:49 +0100 Subject: [ARM] 5113/1: PXA SSP: Additional register definitions for PXA3xx SSP Also add some white space for a little clarity. Signed-off-by: Mark Brown Acked-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/regs-ssp.h | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/regs-ssp.h b/include/asm-arm/arch-pxa/regs-ssp.h index 0255328c3c1..3c04cde2cf1 100644 --- a/include/asm-arm/arch-pxa/regs-ssp.h +++ b/include/asm-arm/arch-pxa/regs-ssp.h @@ -20,6 +20,10 @@ #define SSTSS (0x38) /* SSP Timeslot Status */ #define SSACD (0x3C) /* SSP Audio Clock Divider */ +#if defined(CONFIG_PXA3xx) +#define SSACDD (0x40) /* SSP Audio Clock Dither Divider */ +#endif + /* Common PXA2xx bits first */ #define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */ #define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */ @@ -29,10 +33,12 @@ #define SSCR0_National (0x2 << 4) /* National Microwire */ #define SSCR0_ECS (1 << 6) /* External clock select */ #define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */ + #if defined(CONFIG_PXA25x) #define SSCR0_SCR (0x0000ff00) /* Serial Clock Rate (mask) */ #define SSCR0_SerClkDiv(x) ((((x) - 2)/2) << 8) /* Divisor [2..512] */ -#elif defined(CONFIG_PXA27x) + +#elif defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) #define SSCR0_SCR (0x000fff00) /* Serial Clock Rate (mask) */ #define SSCR0_SerClkDiv(x) (((x) - 1) << 8) /* Divisor [1..4096] */ #define SSCR0_EDSS (1 << 20) /* Extended data size select */ @@ -45,6 +51,10 @@ #define SSCR0_MOD (1 << 31) /* Mode (normal or network) */ #endif +#if defined(CONFIG_PXA3xx) +#define SSCR0_FPCKE (1 << 29) /* FIFO packing enable */ +#endif + #define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */ #define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */ #define SSCR1_LBM (1 << 2) /* Loop-Back Mode */ @@ -109,5 +119,9 @@ #define SSACD_SCDB (1 << 3) /* SSPSYSCLK Divider Bypass */ #define SSACD_ACPS(x) ((x) << 4) /* Audio clock PLL select */ #define SSACD_ACDS(x) ((x) << 0) /* Audio clock divider select */ +#if defined(CONFIG_PXA3xx) +#define SSACD_SCDX8 (1 << 7) /* SYSCLK division ratio select */ +#endif + #endif /* __ASM_ARCH_REGS_SSP_H */ -- cgit v1.2.3 From c316f101a10f2681618ffb537ecba6084d5a137e Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Thu, 10 Jul 2008 20:01:07 +0100 Subject: E-series GPIO / IRQ definitions. --- include/asm-arm/arch-pxa/eseries-gpio.h | 50 +++++++++++++++++++++++++++++++++ include/asm-arm/arch-pxa/eseries-irq.h | 27 ++++++++++++++++++ 2 files changed, 77 insertions(+) create mode 100644 include/asm-arm/arch-pxa/eseries-gpio.h create mode 100644 include/asm-arm/arch-pxa/eseries-irq.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/eseries-gpio.h b/include/asm-arm/arch-pxa/eseries-gpio.h new file mode 100644 index 00000000000..4c90b131027 --- /dev/null +++ b/include/asm-arm/arch-pxa/eseries-gpio.h @@ -0,0 +1,50 @@ +/* + * eseries-gpio.h + * + * Copyright (C) Ian Molton + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +/* e-series power button */ +#define GPIO_ESERIES_POWERBTN 0 + +/* UDC GPIO definitions */ +#define GPIO_E7XX_USB_DISC 13 +#define GPIO_E7XX_USB_PULLUP 3 + +#define GPIO_E800_USB_DISC 4 +#define GPIO_E800_USB_PULLUP 84 + +/* e740 PCMCIA GPIO definitions */ +/* Note: PWR1 seems to be inverted */ +#define GPIO_E740_PCMCIA_CD0 8 +#define GPIO_E740_PCMCIA_CD1 44 +#define GPIO_E740_PCMCIA_RDY0 11 +#define GPIO_E740_PCMCIA_RDY1 6 +#define GPIO_E740_PCMCIA_RST0 27 +#define GPIO_E740_PCMCIA_RST1 24 +#define GPIO_E740_PCMCIA_PWR0 20 +#define GPIO_E740_PCMCIA_PWR1 23 + +/* e750 PCMCIA GPIO definitions */ +#define GPIO_E750_PCMCIA_CD0 8 +#define GPIO_E750_PCMCIA_RDY0 12 +#define GPIO_E750_PCMCIA_RST0 27 +#define GPIO_E750_PCMCIA_PWR0 20 + +/* e800 PCMCIA GPIO definitions */ +#define GPIO_E800_PCMCIA_RST0 69 +#define GPIO_E800_PCMCIA_RST1 72 +#define GPIO_E800_PCMCIA_PWR0 20 +#define GPIO_E800_PCMCIA_PWR1 73 + +/* e7xx IrDA power control */ +#define GPIO_E7XX_IR_ON 38 + +/* ASIC related GPIOs */ +#define GPIO_ESERIES_TMIO_IRQ 5 +#define GPIO_E800_ANGELX_IRQ 8 diff --git a/include/asm-arm/arch-pxa/eseries-irq.h b/include/asm-arm/arch-pxa/eseries-irq.h new file mode 100644 index 00000000000..f2a93d5e31d --- /dev/null +++ b/include/asm-arm/arch-pxa/eseries-irq.h @@ -0,0 +1,27 @@ +/* + * eseries-irq.h + * + * Copyright (C) Ian Molton + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#define ANGELX_IRQ_BASE (IRQ_BOARD_START+8) +#define IRQ_ANGELX(n) (ANGELX_IRQ_BASE + (n)) + +#define ANGELX_RDY0_IRQ IRQ_ANGELX(0) +#define ANGELX_ST0_IRQ IRQ_ANGELX(1) +#define ANGELX_CD0_IRQ IRQ_ANGELX(2) +#define ANGELX_RDY1_IRQ IRQ_ANGELX(3) +#define ANGELX_ST1_IRQ IRQ_ANGELX(4) +#define ANGELX_CD1_IRQ IRQ_ANGELX(5) + +#define TMIO_IRQ_BASE (IRQ_BOARD_START+0) +#define IRQ_TMIO(n) (TMIO_IRQ_BASE + (n)) + +#define TMIO_SD_IRQ IRQ_TMIO(1) +#define TMIO_USB_IRQ IRQ_TMIO(2) + -- cgit v1.2.3 From 8fb105f5cc7f31ff37755945378a668f4c21590e Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Wed, 25 Jun 2008 22:34:51 +0100 Subject: PXA UDC - allow use of inverted GPIO for pullup Signed-off-by: Ian Molton --- include/asm-arm/mach/udc_pxa2xx.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/mach/udc_pxa2xx.h b/include/asm-arm/mach/udc_pxa2xx.h index f9f3606986c..9e5ed7c0f27 100644 --- a/include/asm-arm/mach/udc_pxa2xx.h +++ b/include/asm-arm/mach/udc_pxa2xx.h @@ -23,6 +23,7 @@ struct pxa2xx_udc_mach_info { */ bool gpio_vbus_inverted; u16 gpio_vbus; /* high == vbus present */ + bool gpio_pullup_inverted; u16 gpio_pullup; /* high == pullup activated */ }; -- cgit v1.2.3 From 5d31e43589589e63f5b96abc62372d2ef331c14a Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 11 Jul 2008 12:45:39 +0800 Subject: [ARM] pxa: add base support for PXA930 (aka Tavor-P) Signed-off-by: Eric Miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/hardware.h | 16 ++ include/asm-arm/arch-pxa/mfp-pxa930.h | 491 ++++++++++++++++++++++++++++++++++ include/asm-arm/arch-pxa/mfp.h | 8 + 3 files changed, 515 insertions(+) create mode 100644 include/asm-arm/arch-pxa/mfp-pxa930.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-pxa/hardware.h b/include/asm-arm/arch-pxa/hardware.h index 09868de841a..979a45695d7 100644 --- a/include/asm-arm/arch-pxa/hardware.h +++ b/include/asm-arm/arch-pxa/hardware.h @@ -126,6 +126,16 @@ #define __cpu_is_pxa320(id) (0) #endif +#ifdef CONFIG_CPU_PXA930 +#define __cpu_is_pxa930(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x683; \ + }) +#else +#define __cpu_is_pxa930(id) (0) +#endif + #define cpu_is_pxa21x() \ ({ \ __cpu_is_pxa21x(read_cpuid_id()); \ @@ -161,6 +171,12 @@ __cpu_is_pxa320(read_cpuid_id()); \ }) +#define cpu_is_pxa930() \ + ({ \ + unsigned int id = read_cpuid(CPUID_ID); \ + __cpu_is_pxa930(id); \ + }) + /* * CPUID Core Generation Bit * <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x diff --git a/include/asm-arm/arch-pxa/mfp-pxa930.h b/include/asm-arm/arch-pxa/mfp-pxa930.h new file mode 100644 index 00000000000..c4e945ab192 --- /dev/null +++ b/include/asm-arm/arch-pxa/mfp-pxa930.h @@ -0,0 +1,491 @@ +/* + * linux/include/asm-arm/arch-pxa/mfp-pxa930.h + * + * PXA930 specific MFP configuration definitions + * + * Copyright (C) 2007-2008 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_MFP_PXA9xx_H +#define __ASM_ARCH_MFP_PXA9xx_H + +#include +#include + +/* GPIO */ +#define GPIO46_GPIO MFP_CFG(GPIO46, AF0) +#define GPIO49_GPIO MFP_CFG(GPIO49, AF0) +#define GPIO50_GPIO MFP_CFG(GPIO50, AF0) +#define GPIO51_GPIO MFP_CFG(GPIO51, AF0) +#define GPIO52_GPIO MFP_CFG(GPIO52, AF0) +#define GPIO56_GPIO MFP_CFG(GPIO56, AF0) +#define GPIO58_GPIO MFP_CFG(GPIO58, AF0) +#define GPIO59_GPIO MFP_CFG(GPIO59, AF0) +#define GPIO60_GPIO MFP_CFG(GPIO60, AF0) +#define GPIO61_GPIO MFP_CFG(GPIO61, AF0) +#define GPIO62_GPIO MFP_CFG(GPIO62, AF0) + +#define GSIM_UCLK_GPIO_79 MFP_CFG(GSIM_UCLK, AF0) +#define GSIM_UIO_GPIO_80 MFP_CFG(GSIM_UIO, AF0) +#define GSIM_nURST_GPIO_81 MFP_CFG(GSIM_nURST, AF0) +#define GSIM_UDET_GPIO_82 MFP_CFG(GSIM_UDET, AF0) + +#define DF_IO15_GPIO_28 MFP_CFG(DF_IO15, AF0) +#define DF_IO14_GPIO_29 MFP_CFG(DF_IO14, AF0) +#define DF_IO13_GPIO_30 MFP_CFG(DF_IO13, AF0) +#define DF_IO12_GPIO_31 MFP_CFG(DF_IO12, AF0) +#define DF_IO11_GPIO_32 MFP_CFG(DF_IO11, AF0) +#define DF_IO10_GPIO_33 MFP_CFG(DF_IO10, AF0) +#define DF_IO9_GPIO_34 MFP_CFG(DF_IO9, AF0) +#define DF_IO8_GPIO_35 MFP_CFG(DF_IO8, AF0) +#define DF_IO7_GPIO_36 MFP_CFG(DF_IO7, AF0) +#define DF_IO6_GPIO_37 MFP_CFG(DF_IO6, AF0) +#define DF_IO5_GPIO_38 MFP_CFG(DF_IO5, AF0) +#define DF_IO4_GPIO_39 MFP_CFG(DF_IO4, AF0) +#define DF_IO3_GPIO_40 MFP_CFG(DF_IO3, AF0) +#define DF_IO2_GPIO_41 MFP_CFG(DF_IO2, AF0) +#define DF_IO1_GPIO_42 MFP_CFG(DF_IO1, AF0) +#define DF_IO0_GPIO_43 MFP_CFG(DF_IO0, AF0) +#define DF_nCS0_GPIO_44 MFP_CFG(DF_nCS0, AF0) +#define DF_nCS1_GPIO_45 MFP_CFG(DF_nCS1, AF0) +#define DF_nWE_GPIO_46 MFP_CFG(DF_nWE, AF0) +#define DF_nRE_nOE_GPIO_47 MFP_CFG(DF_nRE_nOE, AF0) +#define DF_CLE_nOE_GPIO_48 MFP_CFG(DF_CLE_nOE, AF0) +#define DF_nADV1_ALE_GPIO_49 MFP_CFG(DF_nADV1_ALE, AF0) +#define DF_nADV2_ALE_GPIO_50 MFP_CFG(DF_nADV2_ALE, AF0) +#define DF_INT_RnB_GPIO_51 MFP_CFG(DF_INT_RnB, AF0) +#define DF_SCLK_E_GPIO_52 MFP_CFG(DF_SCLK_E, AF0) + +#define DF_ADDR0_GPIO_53 MFP_CFG(DF_ADDR0, AF0) +#define DF_ADDR1_GPIO_54 MFP_CFG(DF_ADDR1, AF0) +#define DF_ADDR2_GPIO_55 MFP_CFG(DF_ADDR2, AF0) +#define DF_ADDR3_GPIO_56 MFP_CFG(DF_ADDR3, AF0) +#define nXCVREN_GPIO_57 MFP_CFG(nXCVREN, AF0) +#define nLUA_GPIO_58 MFP_CFG(nLUA, AF0) +#define nLLA_GPIO_59 MFP_CFG(nLLA, AF0) +#define nBE0_GPIO_60 MFP_CFG(nBE0, AF0) +#define nBE1_GPIO_61 MFP_CFG(nBE1, AF0) +#define RDY_GPIO_62 MFP_CFG(RDY, AF0) + +/* Chip Select */ +#define DF_nCS0_nCS2 MFP_CFG_LPM(DF_nCS0, AF3, PULL_HIGH) +#define DF_nCS1_nCS3 MFP_CFG_LPM(DF_nCS1, AF3, PULL_HIGH) + +/* AC97 */ +#define GPIO83_BAC97_SYSCLK MFP_CFG(GPIO83, AF3) +#define GPIO84_BAC97_SDATA_IN0 MFP_CFG(GPIO84, AF3) +#define GPIO85_BAC97_BITCLK MFP_CFG(GPIO85, AF3) +#define GPIO86_BAC97_nRESET MFP_CFG(GPIO86, AF3) +#define GPIO87_BAC97_SYNC MFP_CFG(GPIO87, AF3) +#define GPIO88_BAC97_SDATA_OUT MFP_CFG(GPIO88, AF3) + +/* I2C */ +#define GPIO39_CI2C_SCL MFP_CFG_LPM(GPIO39, AF3, PULL_HIGH) +#define GPIO40_CI2C_SDA MFP_CFG_LPM(GPIO40, AF3, PULL_HIGH) + +#define GPIO51_CI2C_SCL MFP_CFG_LPM(GPIO51, AF3, PULL_HIGH) +#define GPIO52_CI2C_SDA MFP_CFG_LPM(GPIO52, AF3, PULL_HIGH) + +#define GPIO63_CI2C_SCL MFP_CFG_LPM(GPIO63, AF4, PULL_HIGH) +#define GPIO64_CI2C_SDA MFP_CFG_LPM(GPIO64, AF4, PULL_HIGH) + +#define GPIO77_CI2C_SCL MFP_CFG_LPM(GPIO77, AF2, PULL_HIGH) +#define GPIO78_CI2C_SDA MFP_CFG_LPM(GPIO78, AF2, PULL_HIGH) + +#define GPIO89_CI2C_SCL MFP_CFG_LPM(GPIO89, AF1, PULL_HIGH) +#define GPIO90_CI2C_SDA MFP_CFG_LPM(GPIO90, AF1, PULL_HIGH) + +#define GPIO95_CI2C_SCL MFP_CFG_LPM(GPIO95, AF1, PULL_HIGH) +#define GPIO96_CI2C_SDA MFP_CFG_LPM(GPIO96, AF1, PULL_HIGH) + +#define GPIO97_CI2C_SCL MFP_CFG_LPM(GPIO97, AF3, PULL_HIGH) +#define GPIO98_CI2C_SDA MFP_CFG_LPM(GPIO98, AF3, PULL_HIGH) + +/* QCI */ +#define GPIO63_CI_DD_9 MFP_CFG_LPM(GPIO63, AF1, PULL_LOW) +#define GPIO64_CI_DD_8 MFP_CFG_LPM(GPIO64, AF1, PULL_LOW) +#define GPIO65_CI_DD_7 MFP_CFG_LPM(GPIO65, AF1, PULL_LOW) +#define GPIO66_CI_DD_6 MFP_CFG_LPM(GPIO66, AF1, PULL_LOW) +#define GPIO67_CI_DD_5 MFP_CFG_LPM(GPIO67, AF1, PULL_LOW) +#define GPIO68_CI_DD_4 MFP_CFG_LPM(GPIO68, AF1, PULL_LOW) +#define GPIO69_CI_DD_3 MFP_CFG_LPM(GPIO69, AF1, PULL_LOW) +#define GPIO70_CI_DD_2 MFP_CFG_LPM(GPIO70, AF1, PULL_LOW) +#define GPIO71_CI_DD_1 MFP_CFG_LPM(GPIO71, AF1, PULL_LOW) +#define GPIO72_CI_DD_0 MFP_CFG_LPM(GPIO72, AF1, PULL_LOW) +#define GPIO73_CI_HSYNC MFP_CFG_LPM(GPIO73, AF1, PULL_LOW) +#define GPIO74_CI_VSYNC MFP_CFG_LPM(GPIO74, AF1, PULL_LOW) +#define GPIO75_CI_MCLK MFP_CFG_LPM(GPIO75, AF1, PULL_LOW) +#define GPIO76_CI_PCLK MFP_CFG_LPM(GPIO76, AF1, PULL_LOW) + +/* KEYPAD */ +#define GPIO4_KP_DKIN_4 MFP_CFG_LPM(GPIO4, AF3, FLOAT) +#define GPIO5_KP_DKIN_5 MFP_CFG_LPM(GPIO5, AF3, FLOAT) +#define GPIO6_KP_DKIN_6 MFP_CFG_LPM(GPIO6, AF3, FLOAT) +#define GPIO7_KP_DKIN_7 MFP_CFG_LPM(GPIO7, AF3, FLOAT) +#define GPIO8_KP_DKIN_4 MFP_CFG_LPM(GPIO8, AF3, FLOAT) +#define GPIO9_KP_DKIN_5 MFP_CFG_LPM(GPIO9, AF3, FLOAT) +#define GPIO10_KP_DKIN_6 MFP_CFG_LPM(GPIO10, AF3, FLOAT) +#define GPIO11_KP_DKIN_7 MFP_CFG_LPM(GPIO11, AF3, FLOAT) + +#define GPIO12_KP_DKIN_0 MFP_CFG_LPM(GPIO12, AF2, FLOAT) +#define GPIO13_KP_DKIN_1 MFP_CFG_LPM(GPIO13, AF2, FLOAT) +#define GPIO14_KP_DKIN_2 MFP_CFG_LPM(GPIO14, AF2, FLOAT) +#define GPIO15_KP_DKIN_3 MFP_CFG_LPM(GPIO15, AF2, FLOAT) + +#define GPIO41_KP_DKIN_0 MFP_CFG_LPM(GPIO41, AF2, FLOAT) +#define GPIO42_KP_DKIN_1 MFP_CFG_LPM(GPIO42, AF2, FLOAT) +#define GPIO43_KP_DKIN_2 MFP_CFG_LPM(GPIO43, AF2, FLOAT) +#define GPIO44_KP_DKIN_3 MFP_CFG_LPM(GPIO44, AF2, FLOAT) +#define GPIO41_KP_DKIN_4 MFP_CFG_LPM(GPIO41, AF4, FLOAT) +#define GPIO42_KP_DKIN_5 MFP_CFG_LPM(GPIO42, AF4, FLOAT) + +#define GPIO0_KP_MKIN_0 MFP_CFG_LPM(GPIO0, AF1, FLOAT) +#define GPIO2_KP_MKIN_1 MFP_CFG_LPM(GPIO2, AF1, FLOAT) +#define GPIO4_KP_MKIN_2 MFP_CFG_LPM(GPIO4, AF1, FLOAT) +#define GPIO6_KP_MKIN_3 MFP_CFG_LPM(GPIO6, AF1, FLOAT) +#define GPIO8_KP_MKIN_4 MFP_CFG_LPM(GPIO8, AF1, FLOAT) +#define GPIO10_KP_MKIN_5 MFP_CFG_LPM(GPIO10, AF1, FLOAT) +#define GPIO12_KP_MKIN_6 MFP_CFG_LPM(GPIO12, AF1, FLOAT) +#define GPIO14_KP_MKIN_7 MFP_CFG(GPIO14, AF1) +#define GPIO35_KP_MKIN_5 MFP_CFG(GPIO35, AF4) + +#define GPIO1_KP_MKOUT_0 MFP_CFG_LPM(GPIO1, AF1, DRIVE_HIGH) +#define GPIO3_KP_MKOUT_1 MFP_CFG_LPM(GPIO3, AF1, DRIVE_HIGH) +#define GPIO5_KP_MKOUT_2 MFP_CFG_LPM(GPIO5, AF1, DRIVE_HIGH) +#define GPIO7_KP_MKOUT_3 MFP_CFG_LPM(GPIO7, AF1, DRIVE_HIGH) +#define GPIO9_KP_MKOUT_4 MFP_CFG_LPM(GPIO9, AF1, DRIVE_HIGH) +#define GPIO11_KP_MKOUT_5 MFP_CFG_LPM(GPIO11, AF1, DRIVE_HIGH) +#define GPIO13_KP_MKOUT_6 MFP_CFG_LPM(GPIO13, AF1, DRIVE_HIGH) +#define GPIO15_KP_MKOUT_7 MFP_CFG_LPM(GPIO15, AF1, DRIVE_HIGH) +#define GPIO36_KP_MKOUT_5 MFP_CFG_LPM(GPIO36, AF4, DRIVE_HIGH) + +/* LCD */ +#define GPIO17_LCD_FCLK_RD MFP_CFG(GPIO17, AF1) +#define GPIO18_LCD_LCLK_A0 MFP_CFG(GPIO18, AF1) +#define GPIO19_LCD_PCLK_WR MFP_CFG(GPIO19, AF1) +#define GPIO20_LCD_BIAS MFP_CFG(GPIO20, AF1) +#define GPIO21_LCD_CS MFP_CFG(GPIO21, AF1) +#define GPIO22_LCD_CS2 MFP_CFG(GPIO22, AF2) +#define GPIO22_LCD_VSYNC MFP_CFG(GPIO22, AF1) +#define GPIO23_LCD_DD0 MFP_CFG(GPIO23, AF1) +#define GPIO24_LCD_DD1 MFP_CFG(GPIO24, AF1) +#define GPIO25_LCD_DD2 MFP_CFG(GPIO25, AF1) +#define GPIO26_LCD_DD3 MFP_CFG(GPIO26, AF1) +#define GPIO27_LCD_DD4 MFP_CFG(GPIO27, AF1) +#define GPIO28_LCD_DD5 MFP_CFG(GPIO28, AF1) +#define GPIO29_LCD_DD6 MFP_CFG(GPIO29, AF1) +#define GPIO30_LCD_DD7 MFP_CFG(GPIO30, AF1) +#define GPIO31_LCD_DD8 MFP_CFG(GPIO31, AF1) +#define GPIO32_LCD_DD9 MFP_CFG(GPIO32, AF1) +#define GPIO33_LCD_DD10 MFP_CFG(GPIO33, AF1) +#define GPIO34_LCD_DD11 MFP_CFG(GPIO34, AF1) +#define GPIO35_LCD_DD12 MFP_CFG(GPIO35, AF1) +#define GPIO36_LCD_DD13 MFP_CFG(GPIO36, AF1) +#define GPIO37_LCD_DD14 MFP_CFG(GPIO37, AF1) +#define GPIO38_LCD_DD15 MFP_CFG(GPIO38, AF1) +#define GPIO39_LCD_DD16 MFP_CFG(GPIO39, AF1) +#define GPIO40_LCD_DD17 MFP_CFG(GPIO40, AF1) +#define GPIO41_LCD_CS2 MFP_CFG(GPIO41, AF3) +#define GPIO42_LCD_VSYNC2 MFP_CFG(GPIO42, AF3) +#define GPIO44_LCD_DD7 MFP_CFG(GPIO44, AF1) + +/* Mini-LCD */ +#define GPIO17_MLCD_FCLK MFP_CFG(GPIO17, AF3) +#define GPIO18_MLCD_LCLK MFP_CFG(GPIO18, AF3) +#define GPIO19_MLCD_PCLK MFP_CFG(GPIO19, AF3) +#define GPIO20_MLCD_BIAS MFP_CFG(GPIO20, AF3) +#define GPIO23_MLCD_DD0 MFP_CFG(GPIO23, AF3) +#define GPIO24_MLCD_DD1 MFP_CFG(GPIO24, AF3) +#define GPIO25_MLCD_DD2 MFP_CFG(GPIO25, AF3) +#define GPIO26_MLCD_DD3 MFP_CFG(GPIO26, AF3) +#define GPIO27_MLCD_DD4 MFP_CFG(GPIO27, AF3) +#define GPIO28_MLCD_DD5 MFP_CFG(GPIO28, AF3) +#define GPIO29_MLCD_DD6 MFP_CFG(GPIO29, AF3) +#define GPIO30_MLCD_DD7 MFP_CFG(GPIO30, AF3) +#define GPIO31_MLCD_DD8 MFP_CFG(GPIO31, AF3) +#define GPIO32_MLCD_DD9 MFP_CFG(GPIO32, AF3) +#define GPIO33_MLCD_DD10 MFP_CFG(GPIO33, AF3) +#define GPIO34_MLCD_DD11 MFP_CFG(GPIO34, AF3) +#define GPIO35_MLCD_DD12 MFP_CFG(GPIO35, AF3) +#define GPIO36_MLCD_DD13 MFP_CFG(GPIO36, AF3) +#define GPIO37_MLCD_DD14 MFP_CFG(GPIO37, AF3) +#define GPIO38_MLCD_DD15 MFP_CFG(GPIO38, AF3) +#define GPIO44_MLCD_DD7 MFP_CFG(GPIO44, AF5) + +/* MMC1 */ +#define GPIO10_MMC1_DAT3 MFP_CFG(GPIO10, AF4) +#define GPIO11_MMC1_DAT2 MFP_CFG(GPIO11, AF4) +#define GPIO12_MMC1_DAT1 MFP_CFG(GPIO12, AF4) +#define GPIO13_MMC1_DAT0 MFP_CFG(GPIO13, AF4) +#define GPIO14_MMC1_CMD MFP_CFG(GPIO14, AF4) +#define GPIO15_MMC1_CLK MFP_CFG(GPIO15, AF4) +#define GPIO55_MMC1_CMD MFP_CFG(GPIO55, AF3) +#define GPIO56_MMC1_CLK MFP_CFG(GPIO56, AF3) +#define GPIO57_MMC1_DAT0 MFP_CFG(GPIO57, AF3) +#define GPIO58_MMC1_DAT1 MFP_CFG(GPIO58, AF3) +#define GPIO59_MMC1_DAT2 MFP_CFG(GPIO59, AF3) +#define GPIO60_MMC1_DAT3 MFP_CFG(GPIO60, AF3) + +#define DF_ADDR0_MMC1_CLK MFP_CFG(DF_ADDR0, AF2) +#define DF_ADDR1_MMC1_CMD MFP_CFG(DF_ADDR1, AF2) +#define DF_ADDR2_MMC1_DAT0 MFP_CFG(DF_ADDR2, AF2) +#define DF_ADDR3_MMC1_DAT1 MFP_CFG(DF_ADDR3, AF3) +#define nXCVREN_MMC1_DAT2 MFP_CFG(nXCVREN, AF2) + +/* MMC2 */ +#define GPIO31_MMC2_CMD MFP_CFG(GPIO31, AF7) +#define GPIO32_MMC2_CLK MFP_CFG(GPIO32, AF7) +#define GPIO33_MMC2_DAT0 MFP_CFG(GPIO33, AF7) +#define GPIO34_MMC2_DAT1 MFP_CFG(GPIO34, AF7) +#define GPIO35_MMC2_DAT2 MFP_CFG(GPIO35, AF7) +#define GPIO36_MMC2_DAT3 MFP_CFG(GPIO36, AF7) + +#define GPIO101_MMC2_DAT3 MFP_CFG(GPIO101, AF1) +#define GPIO102_MMC2_DAT2 MFP_CFG(GPIO102, AF1) +#define GPIO103_MMC2_DAT1 MFP_CFG(GPIO103, AF1) +#define GPIO104_MMC2_DAT0 MFP_CFG(GPIO104, AF1) +#define GPIO105_MMC2_CMD MFP_CFG(GPIO105, AF1) +#define GPIO106_MMC2_CLK MFP_CFG(GPIO106, AF1) + +#define DF_IO10_MMC2_DAT3 MFP_CFG(DF_IO10, AF3) +#define DF_IO11_MMC2_DAT2 MFP_CFG(DF_IO11, AF3) +#define DF_IO12_MMC2_DAT1 MFP_CFG(DF_IO12, AF3) +#define DF_IO13_MMC2_DAT0 MFP_CFG(DF_IO13, AF3) +#define DF_IO14_MMC2_CLK MFP_CFG(DF_IO14, AF3) +#define DF_IO15_MMC2_CMD MFP_CFG(DF_IO15, AF3) + +/* BSSP1 */ +#define GPIO12_BSSP1_CLK MFP_CFG(GPIO12, AF3) +#define GPIO13_BSSP1_FRM MFP_CFG(GPIO13, AF3) +#define GPIO14_BSSP1_RXD MFP_CFG(GPIO14, AF3) +#define GPIO15_BSSP1_TXD MFP_CFG(GPIO15, AF3) +#define GPIO97_BSSP1_CLK MFP_CFG(GPIO97, AF5) +#define GPIO98_BSSP1_FRM MFP_CFG(GPIO98, AF5) + +/* BSSP2 */ +#define GPIO84_BSSP2_SDATA_IN MFP_CFG(GPIO84, AF1) +#define GPIO85_BSSP2_BITCLK MFP_CFG(GPIO85, AF1) +#define GPIO86_BSSP2_SYSCLK MFP_CFG(GPIO86, AF1) +#define GPIO87_BSSP2_SYNC MFP_CFG(GPIO87, AF1) +#define GPIO88_BSSP2_DATA_OUT MFP_CFG(GPIO88, AF1) +#define GPIO86_BSSP2_SDATA_IN MFP_CFG(GPIO86, AF4) + +/* BSSP3 */ +#define GPIO79_BSSP3_CLK MFP_CFG(GPIO79, AF1) +#define GPIO80_BSSP3_FRM MFP_CFG(GPIO80, AF1) +#define GPIO81_BSSP3_TXD MFP_CFG(GPIO81, AF1) +#define GPIO82_BSSP3_RXD MFP_CFG(GPIO82, AF1) +#define GPIO83_BSSP3_SYSCLK MFP_CFG(GPIO83, AF1) + +/* BSSP4 */ +#define GPIO43_BSSP4_CLK MFP_CFG(GPIO43, AF4) +#define GPIO44_BSSP4_FRM MFP_CFG(GPIO44, AF4) +#define GPIO45_BSSP4_TXD MFP_CFG(GPIO45, AF4) +#define GPIO46_BSSP4_RXD MFP_CFG(GPIO46, AF4) + +#define GPIO51_BSSP4_CLK MFP_CFG(GPIO51, AF4) +#define GPIO52_BSSP4_FRM MFP_CFG(GPIO52, AF4) +#define GPIO53_BSSP4_TXD MFP_CFG(GPIO53, AF4) +#define GPIO54_BSSP4_RXD MFP_CFG(GPIO54, AF4) + +/* GSSP1 */ +#define GPIO79_GSSP1_CLK MFP_CFG(GPIO79, AF2) +#define GPIO80_GSSP1_FRM MFP_CFG(GPIO80, AF2) +#define GPIO81_GSSP1_TXD MFP_CFG(GPIO81, AF2) +#define GPIO82_GSSP1_RXD MFP_CFG(GPIO82, AF2) +#define GPIO83_GSSP1_SYSCLK MFP_CFG(GPIO83, AF2) + +#define GPIO93_GSSP1_CLK MFP_CFG(GPIO93, AF4) +#define GPIO94_GSSP1_FRM MFP_CFG(GPIO94, AF4) +#define GPIO95_GSSP1_TXD MFP_CFG(GPIO95, AF4) +#define GPIO96_GSSP1_RXD MFP_CFG(GPIO96, AF4) + +/* GSSP2 */ +#define GPIO47_GSSP2_CLK MFP_CFG(GPIO47, AF4) +#define GPIO48_GSSP2_FRM MFP_CFG(GPIO48, AF4) +#define GPIO49_GSSP2_RXD MFP_CFG(GPIO49, AF4) +#define GPIO50_GSSP2_TXD MFP_CFG(GPIO50, AF4) + +#define GPIO69_GSSP2_CLK MFP_CFG(GPIO69, AF4) +#define GPIO70_GSSP2_FRM MFP_CFG(GPIO70, AF4) +#define GPIO71_GSSP2_RXD MFP_CFG(GPIO71, AF4) +#define GPIO72_GSSP2_TXD MFP_CFG(GPIO72, AF4) + +#define GPIO84_GSSP2_RXD MFP_CFG(GPIO84, AF2) +#define GPIO85_GSSP2_CLK MFP_CFG(GPIO85, AF2) +#define GPIO86_GSSP2_SYSCLK MFP_CFG(GPIO86, AF2) +#define GPIO87_GSSP2_FRM MFP_CFG(GPIO87, AF2) +#define GPIO88_GSSP2_TXD MFP_CFG(GPIO88, AF2) +#define GPIO86_GSSP2_RXD MFP_CFG(GPIO86, AF5) + +#define GPIO103_GSSP2_CLK MFP_CFG(GPIO103, AF2) +#define GPIO104_GSSP2_FRM MFP_CFG(GPIO104, AF2) +#define GPIO105_GSSP2_RXD MFP_CFG(GPIO105, AF2) +#define GPIO106_GSSP2_TXD MFP_CFG(GPIO106, AF2) + +/* UART1 - FFUART */ +#define GPIO47_UART1_DSR_N MFP_CFG(GPIO47, AF1) +#define GPIO48_UART1_DTR_N MFP_CFG(GPIO48, AF1) +#define GPIO49_UART1_RI MFP_CFG(GPIO49, AF1) +#define GPIO50_UART1_DCD MFP_CFG(GPIO50, AF1) +#define GPIO51_UART1_CTS MFP_CFG(GPIO51, AF1) +#define GPIO52_UART1_RTS MFP_CFG(GPIO52, AF1) +#define GPIO53_UART1_RXD MFP_CFG(GPIO53, AF1) +#define GPIO54_UART1_TXD MFP_CFG(GPIO54, AF1) + +#define GPIO63_UART1_TXD MFP_CFG(GPIO63, AF2) +#define GPIO64_UART1_RXD MFP_CFG(GPIO64, AF2) +#define GPIO65_UART1_DSR MFP_CFG(GPIO65, AF2) +#define GPIO66_UART1_DTR MFP_CFG(GPIO66, AF2) +#define GPIO67_UART1_RI MFP_CFG(GPIO67, AF2) +#define GPIO68_UART1_DCD MFP_CFG(GPIO68, AF2) +#define GPIO69_UART1_CTS MFP_CFG(GPIO69, AF2) +#define GPIO70_UART1_RTS MFP_CFG(GPIO70, AF2) + +/* UART2 - BTUART */ +#define GPIO91_UART2_RXD MFP_CFG(GPIO91, AF1) +#define GPIO92_UART2_TXD MFP_CFG(GPIO92, AF1) +#define GPIO93_UART2_CTS MFP_CFG(GPIO93, AF1) +#define GPIO94_UART2_RTS MFP_CFG(GPIO94, AF1) + +/* UART3 - STUART */ +#define GPIO43_UART3_RTS MFP_CFG(GPIO43, AF3) +#define GPIO44_UART3_CTS MFP_CFG(GPIO44, AF3) +#define GPIO45_UART3_RXD MFP_CFG(GPIO45, AF3) +#define GPIO46_UART3_TXD MFP_CFG(GPIO46, AF3) + +#define GPIO75_UART3_RTS MFP_CFG(GPIO75, AF5) +#define GPIO76_UART3_CTS MFP_CFG(GPIO76, AF5) +#define GPIO77_UART3_TXD MFP_CFG(GPIO77, AF5) +#define GPIO78_UART3_RXD MFP_CFG(GPIO78, AF5) + +/* DFI */ +#define DF_IO0_DF_IO0 MFP_CFG(DF_IO0, AF2) +#define DF_IO1_DF_IO1 MFP_CFG(DF_IO1, AF2) +#define DF_IO2_DF_IO2 MFP_CFG(DF_IO2, AF2) +#define DF_IO3_DF_IO3 MFP_CFG(DF_IO3, AF2) +#define DF_IO4_DF_IO4 MFP_CFG(DF_IO4, AF2) +#define DF_IO5_DF_IO5 MFP_CFG(DF_IO5, AF2) +#define DF_IO6_DF_IO6 MFP_CFG(DF_IO6, AF2) +#define DF_IO7_DF_IO7 MFP_CFG(DF_IO7, AF2) +#define DF_IO8_DF_IO8 MFP_CFG(DF_IO8, AF2) +#define DF_IO9_DF_IO9 MFP_CFG(DF_IO9, AF2) +#define DF_IO10_DF_IO10 MFP_CFG(DF_IO10, AF2) +#define DF_IO11_DF_IO11 MFP_CFG(DF_IO11, AF2) +#define DF_IO12_DF_IO12 MFP_CFG(DF_IO12, AF2) +#define DF_IO13_DF_IO13 MFP_CFG(DF_IO13, AF2) +#define DF_IO14_DF_IO14 MFP_CFG(DF_IO14, AF2) +#define DF_IO15_DF_IO15 MFP_CFG(DF_IO15, AF2) +#define DF_nADV1_ALE_DF_nADV1 MFP_CFG(DF_nADV1_ALE, AF2) +#define DF_nADV2_ALE_DF_nADV2 MFP_CFG(DF_nADV2_ALE, AF2) +#define DF_nCS0_DF_nCS0 MFP_CFG(DF_nCS0, AF2) +#define DF_nCS1_DF_nCS1 MFP_CFG(DF_nCS1, AF2) +#define DF_nRE_nOE_DF_nOE MFP_CFG(DF_nRE_nOE, AF2) +#define DF_nWE_DF_nWE MFP_CFG(DF_nWE, AF2) + +/* DFI - NAND */ +#define DF_CLE_nOE_ND_CLE MFP_CFG_LPM(DF_CLE_nOE, AF1, PULL_HIGH) +#define DF_INT_RnB_ND_INT_RnB MFP_CFG_LPM(DF_INT_RnB, AF1, PULL_LOW) +#define DF_IO0_ND_IO0 MFP_CFG_LPM(DF_IO0, AF1, PULL_LOW) +#define DF_IO1_ND_IO1 MFP_CFG_LPM(DF_IO1, AF1, PULL_LOW) +#define DF_IO2_ND_IO2 MFP_CFG_LPM(DF_IO2, AF1, PULL_LOW) +#define DF_IO3_ND_IO3 MFP_CFG_LPM(DF_IO3, AF1, PULL_LOW) +#define DF_IO4_ND_IO4 MFP_CFG_LPM(DF_IO4, AF1, PULL_LOW) +#define DF_IO5_ND_IO5 MFP_CFG_LPM(DF_IO5, AF1, PULL_LOW) +#define DF_IO6_ND_IO6 MFP_CFG_LPM(DF_IO6, AF1, PULL_LOW) +#define DF_IO7_ND_IO7 MFP_CFG_LPM(DF_IO7, AF1, PULL_LOW) +#define DF_IO8_ND_IO8 MFP_CFG_LPM(DF_IO8, AF1, PULL_LOW) +#define DF_IO9_ND_IO9 MFP_CFG_LPM(DF_IO9, AF1, PULL_LOW) +#define DF_IO10_ND_IO10 MFP_CFG_LPM(DF_IO10, AF1, PULL_LOW) +#define DF_IO11_ND_IO11 MFP_CFG_LPM(DF_IO11, AF1, PULL_LOW) +#define DF_IO12_ND_IO12 MFP_CFG_LPM(DF_IO12, AF1, PULL_LOW) +#define DF_IO13_ND_IO13 MFP_CFG_LPM(DF_IO13, AF1, PULL_LOW) +#define DF_IO14_ND_IO14 MFP_CFG_LPM(DF_IO14, AF1, PULL_LOW) +#define DF_IO15_ND_IO15 MFP_CFG_LPM(DF_IO15, AF1, PULL_LOW) +#define DF_nADV1_ALE_ND_ALE MFP_CFG_LPM(DF_nADV1_ALE, AF1, PULL_HIGH) +#define DF_nADV2_ALE_ND_ALE MFP_CFG_LPM(DF_nADV2_ALE, AF1, PULL_HIGH) +#define DF_nADV2_ALE_nCS3 MFP_CFG_LPM(DF_nADV2_ALE, AF3, PULL_HIGH) +#define DF_nCS0_ND_nCS0 MFP_CFG_LPM(DF_nCS0, AF1, PULL_HIGH) +#define DF_nCS1_ND_nCS1 MFP_CFG_LPM(DF_nCS1, AF1, PULL_HIGH) +#define DF_nRE_nOE_ND_nRE MFP_CFG_LPM(DF_nRE_nOE, AF1, PULL_HIGH) +#define DF_nWE_ND_nWE MFP_CFG_LPM(DF_nWE, AF1, PULL_HIGH) + +/* PWM */ +#define GPIO41_PWM0 MFP_CFG_LPM(GPIO41, AF1, PULL_LOW) +#define GPIO42_PWM1 MFP_CFG_LPM(GPIO42, AF1, PULL_LOW) +#define GPIO43_PWM3 MFP_CFG_LPM(GPIO43, AF1, PULL_LOW) +#define GPIO20_PWM0 MFP_CFG_LPM(GPIO20, AF2, PULL_LOW) +#define GPIO21_PWM2 MFP_CFG_LPM(GPIO21, AF3, PULL_LOW) +#define GPIO22_PWM3 MFP_CFG_LPM(GPIO22, AF3, PULL_LOW) + +/* CIR */ +#define GPIO46_CIR_OUT MFP_CFG(GPIO46, AF1) +#define GPIO77_CIR_OUT MFP_CFG(GPIO77, AF3) + +/* USB P2 */ +#define GPIO0_USB_P2_7 MFP_CFG(GPIO0, AF3) +#define GPIO15_USB_P2_7 MFP_CFG(GPIO15, AF5) +#define GPIO16_USB_P2_7 MFP_CFG(GPIO16, AF2) +#define GPIO48_USB_P2_7 MFP_CFG(GPIO48, AF7) +#define GPIO49_USB_P2_7 MFP_CFG(GPIO49, AF6) +#define DF_IO9_USB_P2_7 MFP_CFG(DF_IO9, AF3) + +#define GPIO48_USB_P2_8 MFP_CFG(GPIO48, AF2) +#define GPIO50_USB_P2_7 MFP_CFG_X(GPIO50, AF2, DS02X, FLOAT) +#define GPIO51_USB_P2_5 MFP_CFG(GPIO51, AF2) +#define GPIO47_USB_P2_4 MFP_CFG(GPIO47, AF2) +#define GPIO53_USB_P2_3 MFP_CFG(GPIO53, AF2) +#define GPIO54_USB_P2_6 MFP_CFG(GPIO54, AF2) +#define GPIO49_USB_P2_2 MFP_CFG(GPIO49, AF2) +#define GPIO52_USB_P2_1 MFP_CFG(GPIO52, AF2) + +#define GPIO63_USB_P2_8 MFP_CFG(GPIO63, AF3) +#define GPIO64_USB_P2_7 MFP_CFG(GPIO64, AF3) +#define GPIO65_USB_P2_6 MFP_CFG(GPIO65, AF3) +#define GPIO66_USG_P2_5 MFP_CFG(GPIO66, AF3) +#define GPIO67_USB_P2_4 MFP_CFG(GPIO67, AF3) +#define GPIO68_USB_P2_3 MFP_CFG(GPIO68, AF3) +#define GPIO69_USB_P2_2 MFP_CFG(GPIO69, AF3) +#define GPIO70_USB_P2_1 MFP_CFG(GPIO70, AF3) + +/* ULPI */ +#define GPIO31_USB_ULPI_D0 MFP_CFG(GPIO31, AF4) +#define GPIO30_USB_ULPI_D1 MFP_CFG(GPIO30, AF7) +#define GPIO33_USB_ULPI_D2 MFP_CFG(GPIO33, AF5) +#define GPIO34_USB_ULPI_D3 MFP_CFG(GPIO34, AF5) +#define GPIO35_USB_ULPI_D4 MFP_CFG(GPIO35, AF5) +#define GPIO36_USB_ULPI_D5 MFP_CFG(GPIO36, AF5) +#define GPIO41_USB_ULPI_D6 MFP_CFG(GPIO41, AF5) +#define GPIO42_USB_ULPI_D7 MFP_CFG(GPIO42, AF5) +#define GPIO37_USB_ULPI_DIR MFP_CFG(GPIO37, AF4) +#define GPIO38_USB_ULPI_CLK MFP_CFG(GPIO38, AF4) +#define GPIO39_USB_ULPI_STP MFP_CFG(GPIO39, AF4) +#define GPIO40_USB_ULPI_NXT MFP_CFG(GPIO40, AF4) + +#define GPIO3_CLK26MOUTDMD MFP_CFG(GPIO3, AF3) +#define GPIO40_CLK26MOUTDMD MFP_CFG(GPIO40, AF7) +#define GPIO94_CLK26MOUTDMD MFP_CFG(GPIO94, AF5) +#define GPIO104_CLK26MOUTDMD MFP_CFG(GPIO104, AF4) +#define DF_ADDR1_CLK26MOUTDMD MFP_CFG(DF_ADDR2, AF3) +#define DF_ADDR3_CLK26MOUTDMD MFP_CFG(DF_ADDR3, AF3) + +#define GPIO14_CLK26MOUT MFP_CFG(GPIO14, AF5) +#define GPIO38_CLK26MOUT MFP_CFG(GPIO38, AF7) +#define GPIO92_CLK26MOUT MFP_CFG(GPIO92, AF5) +#define GPIO105_CLK26MOUT MFP_CFG(GPIO105, AF4) + +#define GPIO2_CLK13MOUTDMD MFP_CFG(GPIO2, AF3) +#define GPIO39_CLK13MOUTDMD MFP_CFG(GPIO39, AF7) +#define GPIO50_CLK13MOUTDMD MFP_CFG(GPIO50, AF3) +#define GPIO93_CLK13MOUTDMD MFP_CFG(GPIO93, AF5) +#define GPIO103_CLK13MOUTDMD MFP_CFG(GPIO103, AF4) +#define DF_ADDR2_CLK13MOUTDMD MFP_CFG(DF_ADDR2, AF3) + +/* 1 wire */ +#define GPIO95_OW_DQ_IN MFP_CFG(GPIO95, AF5) + +#endif /* __ASM_ARCH_MFP_PXA9xx_H */ diff --git a/include/asm-arm/arch-pxa/mfp.h b/include/asm-arm/arch-pxa/mfp.h index 02f6157396d..e7d58798da6 100644 --- a/include/asm-arm/arch-pxa/mfp.h +++ b/include/asm-arm/arch-pxa/mfp.h @@ -210,6 +210,14 @@ enum { MFP_PIN_DF_IO14, MFP_PIN_DF_IO15, + /* additional pins on PXA930 */ + MFP_PIN_GSIM_UIO, + MFP_PIN_GSIM_UCLK, + MFP_PIN_GSIM_UDET, + MFP_PIN_GSIM_nURST, + MFP_PIN_PMIC_INT, + MFP_PIN_RDY, + MFP_PIN_MAX, }; -- cgit v1.2.3 From c5a89c6c0805959f813e8342d6f4040860f6d7db Mon Sep 17 00:00:00 2001 From: Marc Pignat Date: Fri, 30 May 2008 14:07:47 +0200 Subject: mmc: at91_mci: avoid timeouts The at91 mci controller internal state machine seems to often crash. This can be fixed by resetting the controller after each command for at91rm9200 and by setting the MCI_BLKR register on at91sam926*. Signed-off-by: Marc Pignat Signed-off-by: Hans J Koch Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- include/asm-arm/arch-at91/at91_mci.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-at91/at91_mci.h b/include/asm-arm/arch-at91/at91_mci.h index 1551fc24eb4..400ec10014b 100644 --- a/include/asm-arm/arch-at91/at91_mci.h +++ b/include/asm-arm/arch-at91/at91_mci.h @@ -75,6 +75,10 @@ #define AT91_MCI_TRTYP_MULTIPLE (1 << 19) #define AT91_MCI_TRTYP_STREAM (2 << 19) +#define AT91_MCI_BLKR 0x18 /* Block Register */ +#define AT91_MCI_BLKR_BCNT(n) ((0xffff & (n)) << 0) /* Block count */ +#define AT91_MCI_BLKR_BLKLEN(n) ((0xffff & (n)) << 16) /* Block lenght */ + #define AT91_MCI_RSPR(n) (0x20 + ((n) * 4)) /* Response Registers 0-3 */ #define AT91_MCR_RDR 0x30 /* Receive Data Register */ #define AT91_MCR_TDR 0x34 /* Transmit Data Register */ -- cgit v1.2.3 From be518018c6b9224c02284fb243207ef741c31ec6 Mon Sep 17 00:00:00 2001 From: Thomas Kleffel Date: Mon, 30 Jun 2008 22:40:24 +0100 Subject: MMC: S3C24XX MMC/SD driver. This is the latest S3C MMC/SD driver by Thomas Kleffel with cleanups as suggested by AKPM done by Ben Dooks. Signed-off-by: Ben Dooks Signed-off-by: Thomas Kleffel Signed-off-by: Pierre Ossman --- include/asm-arm/arch-s3c2410/regs-sdi.h | 20 +++++++++++++++++--- 1 file changed, 17 insertions(+), 3 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-s3c2410/regs-sdi.h b/include/asm-arm/arch-s3c2410/regs-sdi.h index bb9d30b7295..bfb222fa4ab 100644 --- a/include/asm-arm/arch-s3c2410/regs-sdi.h +++ b/include/asm-arm/arch-s3c2410/regs-sdi.h @@ -28,9 +28,15 @@ #define S3C2410_SDIDCNT (0x30) #define S3C2410_SDIDSTA (0x34) #define S3C2410_SDIFSTA (0x38) + #define S3C2410_SDIDATA (0x3C) #define S3C2410_SDIIMSK (0x40) +#define S3C2440_SDIDATA (0x40) +#define S3C2440_SDIIMSK (0x3C) + +#define S3C2440_SDICON_SDRESET (1<<8) +#define S3C2440_SDICON_MMCCLOCK (1<<5) #define S3C2410_SDICON_BYTEORDER (1<<4) #define S3C2410_SDICON_SDIOIRQ (1<<3) #define S3C2410_SDICON_RWAITEN (1<<2) @@ -42,7 +48,8 @@ #define S3C2410_SDICMDCON_LONGRSP (1<<10) #define S3C2410_SDICMDCON_WAITRSP (1<<9) #define S3C2410_SDICMDCON_CMDSTART (1<<8) -#define S3C2410_SDICMDCON_INDEX (0xff) +#define S3C2410_SDICMDCON_SENDERHOST (1<<6) +#define S3C2410_SDICMDCON_INDEX (0x3f) #define S3C2410_SDICMDSTAT_CRCFAIL (1<<12) #define S3C2410_SDICMDSTAT_CMDSENT (1<<11) @@ -51,6 +58,9 @@ #define S3C2410_SDICMDSTAT_XFERING (1<<8) #define S3C2410_SDICMDSTAT_INDEX (0xff) +#define S3C2440_SDIDCON_DS_BYTE (0<<22) +#define S3C2440_SDIDCON_DS_HALFWORD (1<<22) +#define S3C2440_SDIDCON_DS_WORD (2<<22) #define S3C2410_SDIDCON_IRQPERIOD (1<<21) #define S3C2410_SDIDCON_TXAFTERRESP (1<<20) #define S3C2410_SDIDCON_RXAFTERCMD (1<<19) @@ -59,6 +69,7 @@ #define S3C2410_SDIDCON_WIDEBUS (1<<16) #define S3C2410_SDIDCON_DMAEN (1<<15) #define S3C2410_SDIDCON_STOP (1<<14) +#define S3C2440_SDIDCON_DATSTART (1<<14) #define S3C2410_SDIDCON_DATMODE (3<<12) #define S3C2410_SDIDCON_BLKNUM (0x7ff) @@ -68,6 +79,7 @@ #define S3C2410_SDIDCON_XFER_RXSTART (2<<12) #define S3C2410_SDIDCON_XFER_TXSTART (3<<12) +#define S3C2410_SDIDCON_BLKNUM_MASK (0xFFF) #define S3C2410_SDIDCNT_BLKNUM_SHIFT (12) #define S3C2410_SDIDSTA_RDYWAITREQ (1<<10) @@ -82,10 +94,12 @@ #define S3C2410_SDIDSTA_TXDATAON (1<<1) #define S3C2410_SDIDSTA_RXDATAON (1<<0) +#define S3C2440_SDIFSTA_FIFORESET (1<<16) +#define S3C2440_SDIFSTA_FIFOFAIL (3<<14) /* 3 is correct (2 bits) */ #define S3C2410_SDIFSTA_TFDET (1<<13) #define S3C2410_SDIFSTA_RFDET (1<<12) -#define S3C2410_SDIFSTA_TXHALF (1<<11) -#define S3C2410_SDIFSTA_TXEMPTY (1<<10) +#define S3C2410_SDIFSTA_TFHALF (1<<11) +#define S3C2410_SDIFSTA_TFEMPTY (1<<10) #define S3C2410_SDIFSTA_RFLAST (1<<9) #define S3C2410_SDIFSTA_RFFULL (1<<8) #define S3C2410_SDIFSTA_RFHALF (1<<7) -- cgit v1.2.3 From edb5a98e43682d66c98ddd1dee863d867807546e Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:29 +0100 Subject: MMC: S3C24XX: Add platform data for MMC/SD driver This patch adds platform data support to the s3mci driver. This allows flexible board-specific configuration of set_power, card detect and read only pins. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- include/asm-arm/plat-s3c24xx/mci.h | 12 ++++++++++++ 1 file changed, 12 insertions(+) create mode 100644 include/asm-arm/plat-s3c24xx/mci.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-s3c24xx/mci.h b/include/asm-arm/plat-s3c24xx/mci.h new file mode 100644 index 00000000000..5be2c1449c6 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/mci.h @@ -0,0 +1,12 @@ +#ifndef _ARCH_MCI_H +#define _ARCH_MCI_H + +struct s3c24xx_mci_pdata { + unsigned int gpio_detect; + unsigned int gpio_wprotect; + unsigned long ocr_avail; + void (*set_power)(unsigned char power_mode, + unsigned short vdd); +}; + +#endif /* _ARCH_NCI_H */ -- cgit v1.2.3 From cf0984c8edf63017fcc2ead212ca057877e345df Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:30 +0100 Subject: MMC: S3C24XX: Add support to invert write protect line Support for inverting the sense of the MMC driver's write protect detection line. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- include/asm-arm/plat-s3c24xx/mci.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-s3c24xx/mci.h b/include/asm-arm/plat-s3c24xx/mci.h index 5be2c1449c6..4f4ccd18f0c 100644 --- a/include/asm-arm/plat-s3c24xx/mci.h +++ b/include/asm-arm/plat-s3c24xx/mci.h @@ -2,6 +2,8 @@ #define _ARCH_MCI_H struct s3c24xx_mci_pdata { + unsigned int wprotect_invert : 1; + unsigned int gpio_detect; unsigned int gpio_wprotect; unsigned long ocr_avail; -- cgit v1.2.3 From 50a845700b3b55f825b0eb901b03d6091f66d9f4 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:36 +0100 Subject: MMC: S3C24XX: Add media presence test to request handling. Ensure that we have physical media present before attempting to send a request to a card. This ensures that we do not get flooded by errors from commands that can never be completed timing out. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- include/asm-arm/plat-s3c24xx/mci.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/asm-arm') diff --git a/include/asm-arm/plat-s3c24xx/mci.h b/include/asm-arm/plat-s3c24xx/mci.h index 4f4ccd18f0c..2d0852ac3b2 100644 --- a/include/asm-arm/plat-s3c24xx/mci.h +++ b/include/asm-arm/plat-s3c24xx/mci.h @@ -3,6 +3,7 @@ struct s3c24xx_mci_pdata { unsigned int wprotect_invert : 1; + unsigned int detect_invert : 1; /* set => detect active high. */ unsigned int gpio_detect; unsigned int gpio_wprotect; -- cgit v1.2.3 From 2a46fa13d788364c093c4296fe01cae837aa8919 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Thu, 17 Jul 2008 17:59:56 -0700 Subject: iop_adma: cleanup iop_chan_xor_slot_count - use a table for iop13xx, trade text for data - shrink the iop3xx to a cache line Signed-off-by: Dan Williams --- include/asm-arm/arch-iop13xx/adma.h | 18 +++++++----------- include/asm-arm/hardware/iop3xx-adma.h | 4 ++-- 2 files changed, 9 insertions(+), 13 deletions(-) (limited to 'include/asm-arm') diff --git a/include/asm-arm/arch-iop13xx/adma.h b/include/asm-arm/arch-iop13xx/adma.h index 90d14ee564f..ef4f5da2029 100644 --- a/include/asm-arm/arch-iop13xx/adma.h +++ b/include/asm-arm/arch-iop13xx/adma.h @@ -198,17 +198,13 @@ iop_chan_memset_slot_count(size_t len, int *slots_per_op) static inline int iop_chan_xor_slot_count(size_t len, int src_cnt, int *slots_per_op) { - int num_slots; - /* slots_to_find = 1 for basic descriptor + 1 per 4 sources above 1 - * (1 source => 8 bytes) (1 slot => 32 bytes) - */ - num_slots = 1 + (((src_cnt - 1) << 3) >> 5); - if (((src_cnt - 1) << 3) & 0x1f) - num_slots++; - - *slots_per_op = num_slots; - - return num_slots; + static const char slot_count_table[] = { 1, 2, 2, 2, + 2, 3, 3, 3, + 3, 4, 4, 4, + 4, 5, 5, 5, + }; + *slots_per_op = slot_count_table[src_cnt - 1]; + return *slots_per_op; } #define ADMA_MAX_BYTE_COUNT (16 * 1024 * 1024) diff --git a/include/asm-arm/hardware/iop3xx-adma.h b/include/asm-arm/hardware/iop3xx-adma.h index a32b86ac62a..af64676650a 100644 --- a/include/asm-arm/hardware/iop3xx-adma.h +++ b/include/asm-arm/hardware/iop3xx-adma.h @@ -260,7 +260,7 @@ static inline int iop_chan_memset_slot_count(size_t len, int *slots_per_op) static inline int iop3xx_aau_xor_slot_count(size_t len, int src_cnt, int *slots_per_op) { - static const int slot_count_table[] = { 0, + static const char slot_count_table[] = { 1, 1, 1, 1, /* 01 - 04 */ 2, 2, 2, 2, /* 05 - 08 */ 4, 4, 4, 4, /* 09 - 12 */ @@ -270,7 +270,7 @@ static inline int iop3xx_aau_xor_slot_count(size_t len, int src_cnt, 8, 8, 8, 8, /* 25 - 28 */ 8, 8, 8, 8, /* 29 - 32 */ }; - *slots_per_op = slot_count_table[src_cnt]; + *slots_per_op = slot_count_table[src_cnt - 1]; return *slots_per_op; } -- cgit v1.2.3 From 5cbad0ebf45c5417104b383dc0e34f64fa7f2473 Mon Sep 17 00:00:00 2001 From: Jason Wessel Date: Wed, 20 Feb 2008 13:33:40 -0600 Subject: kgdb: support for ARCH=arm This patch adds the ARCH=arm specific a kgdb backend, originally written by Deepak Saxena and George Davis . Geoff Levand , Nicolas Pitre, Manish Lachwani, and Jason Wessel have contributed various fixups here as well. The KGDB patch makes one change to the core ARM architecture such that the traps are initialized early for use with the debugger or other subsystems. [ mingo@elte.hu: small cleanups. ] [ ben-linux@fluff.org: fixed early_trap_init ] Signed-off-by: Jason Wessel Acked-by: Deepak Saxena --- include/asm-arm/kgdb.h | 104 ++++++++++++++++++++++++++++++++++++++++++++++++ include/asm-arm/traps.h | 2 + 2 files changed, 106 insertions(+) create mode 100644 include/asm-arm/kgdb.h (limited to 'include/asm-arm') diff --git a/include/asm-arm/kgdb.h b/include/asm-arm/kgdb.h new file mode 100644 index 00000000000..67af4b84198 --- /dev/null +++ b/include/asm-arm/kgdb.h @@ -0,0 +1,104 @@ +/* + * ARM KGDB support + * + * Author: Deepak Saxena + * + * Copyright (C) 2002 MontaVista Software Inc. + * + */ + +#ifndef __ARM_KGDB_H__ +#define __ARM_KGDB_H__ + +#include + +/* + * GDB assumes that we're a user process being debugged, so + * it will send us an SWI command to write into memory as the + * debug trap. When an SWI occurs, the next instruction addr is + * placed into R14_svc before jumping to the vector trap. + * This doesn't work for kernel debugging as we are already in SVC + * we would loose the kernel's LR, which is a bad thing. This + * is bad thing. + * + * By doing this as an undefined instruction trap, we force a mode + * switch from SVC to UND mode, allowing us to save full kernel state. + * + * We also define a KGDB_COMPILED_BREAK which can be used to compile + * in breakpoints. This is important for things like sysrq-G and for + * the initial breakpoint from trap_init(). + * + * Note to ARM HW designers: Add real trap support like SH && PPC to + * make our lives much much simpler. :) + */ +#define BREAK_INSTR_SIZE 4 +#define GDB_BREAKINST 0xef9f0001 +#define KGDB_BREAKINST 0xe7ffdefe +#define KGDB_COMPILED_BREAK 0xe7ffdeff +#define CACHE_FLUSH_IS_SAFE 1 + +#ifndef __ASSEMBLY__ + +static inline void arch_kgdb_breakpoint(void) +{ + asm(".word 0xe7ffdeff"); +} + +extern void kgdb_handle_bus_error(void); +extern int kgdb_fault_expected; + +#endif /* !__ASSEMBLY__ */ + +/* + * From Kevin Hilman: + * + * gdb is expecting the following registers layout. + * + * r0-r15: 1 long word each + * f0-f7: unused, 3 long words each !! + * fps: unused, 1 long word + * cpsr: 1 long word + * + * Even though f0-f7 and fps are not used, they need to be + * present in the registers sent for correct processing in + * the host-side gdb. + * + * In particular, it is crucial that CPSR is in the right place, + * otherwise gdb will not be able to correctly interpret stepping over + * conditional branches. + */ +#define _GP_REGS 16 +#define _FP_REGS 8 +#define _EXTRA_REGS 2 +#define GDB_MAX_REGS (_GP_REGS + (_FP_REGS * 3) + _EXTRA_REGS) + +#define KGDB_MAX_NO_CPUS 1 +#define BUFMAX 400 +#define NUMREGBYTES (GDB_MAX_REGS << 2) +#define NUMCRITREGBYTES (32 << 2) + +#define _R0 0 +#define _R1 1 +#define _R2 2 +#define _R3 3 +#define _R4 4 +#define _R5 5 +#define _R6 6 +#define _R7 7 +#define _R8 8 +#define _R9 9 +#define _R10 10 +#define _FP 11 +#define _IP 12 +#define _SPT 13 +#define _LR 14 +#define _PC 15 +#define _CPSR (GDB_MAX_REGS - 1) + +/* + * So that we can denote the end of a frame for tracing, + * in the simple case: + */ +#define CFI_END_FRAME(func) __CFI_END_FRAME(_PC, _SPT, func) + +#endif /* __ASM_KGDB_H__ */ diff --git a/include/asm-arm/traps.h b/include/asm-arm/traps.h index f1541afcf85..aa399aec568 100644 --- a/include/asm-arm/traps.h +++ b/include/asm-arm/traps.h @@ -24,4 +24,6 @@ static inline int in_exception_text(unsigned long ptr) ptr < (unsigned long)&__exception_text_end; } +extern void __init early_trap_init(void); + #endif -- cgit v1.2.3