/* * Copyright (C) 1996 Linus Torvalds & author (see below) */ #include #include #include #include #include #include #include #include #include #include #include #include /* * Changing this #undef to #define may solve start up problems in some systems. */ #undef ALWAYS_SET_DTC2278_PIO_MODE /* * From: andy@cercle.cts.com (Dyan Wile) * * Below is a patch for DTC-2278 - alike software-programmable controllers * The code enables the secondary IDE controller and the PIO4 (3?) timings on * the primary (EIDE). You may probably have to enable the 32-bit support to * get the full speed. You better get the disk interrupts disabled ( hdparm -u0 * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my * filesystem corrupted with -u1, but under heavy disk load only :-) * * This card is now forced to use the "serialize" feature, * and irq-unmasking is disallowed. If io_32bit is enabled, * it must be done for BOTH drives on each interface. * * This code was written for the DTC2278E, but might work with any of these: * * DTC2278S has only a single IDE interface. * DTC2278D has two IDE interfaces and is otherwise identical to the S version. * DTC2278E also has serial ports and a printer port * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford * * There may be a fourth controller type. The S and D versions use the * Winbond chip, and I think the E version does also. * */ static void sub22 (char b, char c) { int i; for(i = 0; i < 3; ++i) { inb(0x3f6); outb_p(b,0xb0); inb(0x3f6); outb_p(c,0xb4); inb(0x3f6); if(inb(0xb4) == c) { outb_p(7,0xb0); inb(0x3f6); return; /* success */ } } } static DEFINE_SPINLOCK(dtc2278_lock); static void dtc2278_set_pio_mode(ide_drive_t *drive, const u8 pio) { unsigned long flags; if (pio >= 3) { spin_lock_irqsave(&dtc2278_lock, flags); /* * This enables PIO mode4 (3?) on the first interface */ sub22(1,0xc3); sub22(0,0xa0); spin_unlock_irqrestore(&dtc2278_lock, flags); } else { /* we don't know how to set it back again.. */ /* Actually we do - there is a data sheet available for the Winbond but does anyone actually care */ } } static int __init dtc2278_probe(void) { unsigned long flags; ide_hwif_t *hwif, *mate; static u8 idx[4] = { 0, 1, 0xff, 0xff }; hwif = &ide_hwifs[0]; mate = &ide_hwifs[1]; if (hwif->chipset != ide_unknown || mate->chipset != ide_unknown) return 1; local_irq_save(flags); /* * This enables the second interface */ outb_p(4,0xb0); inb(0x3f6); outb_p(0x20,0xb4); inb(0x3f6); #ifdef ALWAYS_SET_DTC2278_PIO_MODE /* * This enables PIO mode4 (3?) on the first interface * and may solve start-up problems for some people. */ sub22(1,0xc3); sub22(0,0xa0); #endif local_irq_restore(flags); hwif->serialized = 1; hwif->no_io_32bit = 1; /* disallow ->io_32bit changes */ hwif->chipset = ide_dtc2278; hwif->pio_mask = ATA_PIO4; hwif->set_pio_mode = &dtc2278_set_pio_mode; hwif->drives[0].no_unmask = 1; hwif->drives[1].no_unmask = 1; hwif->drives[0].io_32bit = 1; hwif->drives[1].io_32bit = 1; hwif->mate = mate; mate->serialized = 1; mate->no_io_32bit = 1; mate->chipset = ide_dtc2278; mate->pio_mask = ATA_PIO4; mate->drives[0].no_unmask = 1; mate->drives[1].no_unmask = 1; mate->drives[0].io_32bit = 1; mate->drives[1].io_32bit = 1; mate->mate = hwif; mate->channel = 1; ide_device_add(idx); return 0; } int probe_dtc2278 = 0; module_param_named(probe, probe_dtc2278, bool, 0); MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets"); static int __init dtc2278_init(void) { if (probe_dtc2278 == 0) return -ENODEV; if (dtc2278_probe()) { printk(KERN_ERR "dtc2278: ide interfaces already in use!\n"); return -EBUSY; } return 0; } module_init(dtc2278_init); MODULE_AUTHOR("See Local File"); MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets"); MODULE_LICENSE("GPL");