/* * SL82C105/Winbond 553 IDE driver * * Maintainer unknown. * * Drive tuning added from Rebel.com's kernel sources * -- Russell King (15/11/98) linux@arm.linux.org.uk * * Merge in Russell's HW workarounds, fix various problems * with the timing registers setup. * -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org * * Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com> * Copyright (C) 2007 Bartlomiej Zolnierkiewicz */ #include <linux/types.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/pci.h> #include <linux/ide.h> #include <asm/io.h> #define DRV_NAME "sl82c105" #undef DEBUG #ifdef DEBUG #define DBG(arg) printk arg #else #define DBG(fmt,...) #endif /* * SL82C105 PCI config register 0x40 bits. */ #define CTRL_IDE_IRQB (1 << 30) #define CTRL_IDE_IRQA (1 << 28) #define CTRL_LEGIRQ (1 << 11) #define CTRL_P1F16 (1 << 5) #define CTRL_P1EN (1 << 4) #define CTRL_P0F16 (1 << 1) #define CTRL_P0EN (1 << 0) /* * Convert a PIO mode and cycle time to the required on/off times * for the interface. This has protection against runaway timings. */ static unsigned int get_pio_timings(ide_drive_t *drive, u8 pio) { struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio); unsigned int cmd_on, cmd_off; u8 iordy = 0; cmd_on = (t->active + 29) / 30; cmd_off = (ide_pio_cycle_time(drive, pio) - 30 * cmd_on + 29) / 30; if (cmd_on == 0) cmd_on = 1; if (cmd_off == 0) cmd_off = 1; if ((pio > 2 || ata_id_has_iordy(drive->id)) && !(pio > 4 && ata_id_is_cfa(drive->id))) iordy = 0x40; return (cmd_on - 1) << 8 | (cmd_off - 1) | iordy; } /* * Configure the chipset for PIO mode. */ static void sl82c105_set_pio_mode(ide_drive_t *drive, const u8 pio) { struct pci_dev *dev = to_pci_dev(drive->hwif->dev); int reg = 0x44 + drive->dn * 4; u16 drv_ctrl; drv_ctrl = get_pio_timings(drive, pio); /* * Store the PIO timings so that we can restore them * in case DMA will be turned off... */ drive->drive_data &= 0xffff0000; drive->drive_data |= drv_ctrl; pci_write_config_word(dev, reg, drv_ctrl); pci_read_config_word (dev, reg, &drv_ctrl); printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name, ide_xfer_verbose(pio + XFER_PIO_0), ide_pio_cycle_time(drive, pio), drv_ctrl); } /* * Configure the chipset for DMA mode. */ static void sl82c105_set_dma_mode(ide_drive_t *drive, const u8 speed) { static u16 mwdma_timings[] = {0x0707, 0x0201, 0x0200}; u16 drv_ctrl; DBG(("sl82c105_tune_chipset(drive:%s, speed:%s)\n", drive->name, ide_xfer_verbose(speed))); drv_ctrl = mwdma_timings[speed - XFER_MW_DMA_0]; /* * Store the DMA timings so that we can actually program * them when DMA will be turned on... */ drive->drive_data &= 0x0000ffff; drive->drive_data |= (unsigned long)drv_ctrl << 16; } /* * The SL82C105 holds off all IDE interrupts while in DMA mode until * all DMA activity is completed. Sometimes this causes problems (eg, * when the drive wants to report an error condition). * * 0x7e is a "chip testing" register. Bit 2 resets the DMA controller * state machine. We need to kick this to work around various bugs. */ static inline void sl82c105_reset_host(struct pci_dev *dev) { u16 val; pci_read_config_word(dev, 0x7e, &val); pci_write_config_word(dev, 0x7e, val | (1 << 2)); pci_write_config_word(dev, 0x7e, val & ~(1 << 2)); } /* * If we get an IRQ timeout, it might be that the DMA state machine * got confused. Fix from Todd Inglett. Details from Winbond. * * This function is called when the IDE timer expires, the drive * indicates that it is READY, and we were waiting for DMA to complete. */ static void sl82c105_dma_lost_irq(ide_drive_t *drive) { ide_hwif_t *hwif = drive->hwif; struct pci_dev *dev = to_pci_dev(hwif->dev); u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA; u8 dma_cmd; printk("sl82c105: lost IRQ, resetting host\n"); /* * Check the raw interrupt from the drive. */ pci_read_config_dword(dev, 0x40, &val); if (val & mask) printk("sl82c105: drive was requesting IRQ, but host lost it\n"); /* * Was DMA enabled? If so, disable it - we're resetting the * host. The IDE layer will be handling the drive for us. */ dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD); if (dma_cmd & 1) { outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD); printk("sl82c105: DMA was enabled\n"); } sl82c105_reset_host(dev); } /* * ATAPI devices can cause the SL82C105 DMA state machine to go gaga. * Winbond recommend that the DMA state machine is reset prior to * setting the bus master DMA enable bit. * * The generic IDE core will have disabled the BMEN bit before this * function is called. */ static void sl82c105_dma_start(ide_drive_t *drive) { ide_hwif_t *hwif = drive->hwif; struct pci_dev *dev = to_pci_dev(hwif->dev); int reg = 0x44 + drive->dn * 4; DBG(("%s(drive:%s)\n", __func__, drive->name)); pci_write_config_word(dev, reg, drive->drive_data >> 16); sl82c105_reset_host(dev); ide_dma_start(drive); } static void sl82c105_dma_clear(ide_drive_t *drive) { struct pci_dev *dev = to_pci_dev(drive->hwif->dev); DBG(("sl82c105_dma_clear(drive:%s)\n", drive->name)); sl82c105_reset_host(dev); } static int sl82c105_dma_end(ide_drive_t *drive) { struct pci_dev *dev = to_pci_dev(drive->hwif->dev); int reg = 0x44 + drive->dn * 4; int ret; DBG(("%s(drive:%s)\n", __func__, drive->name)); ret = ide_dma_end(drive); pci_write_config_word(dev, reg, drive->drive_data); return ret; } /* * ATA reset will clear the 16 bits mode in the control * register, we need to reprogram it */ static void sl82c105_resetproc(ide_drive_t *drive) { struct pci_dev *dev = to_pci_dev(drive->hwif->dev); u32 val; DBG(("sl82c105_resetproc(drive:%s)\n", drive->name)); pci_read_config_dword(dev, 0x40, &val); val |= (CTRL_P1F16 | CTRL_P0F16); pci_write_config_dword(dev, 0x40, val); } /* * Return the revision of the Winbond bridge * which this function is part of. */ static u8 sl82c105_bridge_revision(struct pci_dev *dev) { struct pci_dev *bridge; /* * The bridge should be part of the same device, but function 0. */ bridge = pci_get_bus_and_slot(dev->bus->number, PCI_DEVFN(PCI_SLOT(dev->devfn), 0)); if (!bridge) return -1; /* * Make sure it is a Winbond 553 and is an ISA bridge. */ if (bridge->vendor != PCI_VENDOR_ID_WINBOND || bridge->device != PCI_DEVICE_ID_WINBOND_83C553 || bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) { pci_dev_put(bridge); return -1; } /* * We need to find function 0's revision, not function 1 */ pci_dev_put(bridge); return bridge->revision; } /* * Enable the PCI device * * --BenH: It's arch fixup code that should enable channels that * have not been enabled by firmware. I decided we can still enable * channel 0 here at least, but channel 1 has to be enabled by * firmware or arch code. We still set both to 16 bits mode. */ static int init_chipset_sl82c105(struct pci_dev *dev) { u32 val; DBG(("init_chipset_sl82c105()\n")); pci_read_config_dword(dev, 0x40, &val); val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16; pci_write_config_dword(dev, 0x40, val); return 0; } static const struct ide_port_ops sl82c105_port_ops = { .set_pio_mode = sl82c105_set_pio_mode, .set_dma_mode = sl82c105_set_dma_mode, .resetproc = sl82c105_resetproc, }; static const struct ide_dma_ops sl82c105_dma_ops = { .dma_host_set = ide_dma_host_set, .dma_setup = ide_dma_setup, .dma_start = sl82c105_dma_start, .dma_end = sl82c105_dma_end, .dma_test_irq = ide_dma_test_irq, .dma_lost_irq = sl82c105_dma_lost_irq, .dma_timer_expiry = ide_dma_sff_timer_expiry, .dma_clear = sl82c105_dma_clear, .dma_sff_read_status = ide_dma_sff_read_status, }; static const struct ide_port_info sl82c105_chipset __devinitdata = { .name = DRV_NAME, .init_chipset = init_chipset_sl82c105, .enablebits = {{0x40,0x01,0x01}, {0x40,0x10,0x10}}, .port_ops = &sl82c105_port_ops, .dma_ops = &sl82c105_dma_ops, .host_flags = IDE_HFLAG_IO_32BIT | IDE_HFLAG_UNMASK_IRQS | IDE_HFLAG_SERIALIZE_DMA | IDE_HFLAG_NO_AUTODMA, .pio_mask = ATA_PIO5, .mwdma_mask = ATA_MWDMA2, }; static int __devinit sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id) { struct ide_port_info d = sl82c105_chipset; u8 rev = sl82c105_bridge_revision(dev); if (rev <= 5) { /* * Never ever EVER under any circumstances enable * DMA when the bridge is this old. */ printk(KERN_INFO DRV_NAME ": Winbond W83C553 bridge " "revision %d, BM-DMA disabled\n", rev); d.dma_ops = NULL; d.mwdma_mask = 0; d.host_flags &= ~IDE_HFLAG_SERIALIZE_DMA; } return ide_pci_init_one(dev, &d, NULL); } static const struct pci_device_id sl82c105_pci_tbl[] = { { PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0 }, { 0, }, }; MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl); static struct pci_driver sl82c105_pci_driver = { .name = "W82C105_IDE", .id_table = sl82c105_pci_tbl, .probe = sl82c105_init_one, .remove = ide_pci_remove, .suspend = ide_pci_suspend, .resume = ide_pci_resume, }; static int __init sl82c105_ide_init(void) { return ide_pci_register_driver(&sl82c105_pci_driver); } static void __exit sl82c105_ide_exit(void) { pci_unregister_driver(&sl82c105_pci_driver); } module_init(sl82c105_ide_init); module_exit(sl82c105_ide_exit); MODULE_DESCRIPTION("PCI driver module for W82C105 IDE"); MODULE_LICENSE("GPL");