# # Touchscreen driver configuration # menuconfig INPUT_TOUCHSCREEN bool "Touchscreens" help Say Y here, and a list of supported touchscreens will be displayed. This option doesn't affect the kernel. If unsure, say Y. if INPUT_TOUCHSCREEN config TOUCHSCREEN_ADS7846 tristate "ADS 7846/7843 based touchscreens" depends on SPI_MASTER depends on HWMON = n || HWMON help Say Y here if you have a touchscreen interface using the ADS7846 or ADS7843 controller, and your board-specific setup code includes that in its table of SPI devices. If HWMON is selected, and the driver is told the reference voltage on your board, you will also get hwmon interfaces for the voltage (and on ads7846, temperature) sensors of this chip. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ads7846. config TOUCHSCREEN_BITSY tristate "Compaq iPAQ H3600 (Bitsy) touchscreen" depends on SA1100_BITSY select SERIO help Say Y here if you have the h3600 (Bitsy) touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called h3600_ts_input. config TOUCHSCREEN_CORGI tristate "SharpSL (Corgi and Spitz series) touchscreen driver" depends on PXA_SHARPSL default y help Say Y here to enable the driver for the touchscreen on the Sharp SL-C7xx and SL-Cxx00 series of PDAs. If unsure, say N. To compile this driver as a module, choose M here: the module will be called corgi_ts. config TOUCHSCREEN_GUNZE tristate "Gunze AHL-51S touchscreen" select SERIO help Say Y here if you have the Gunze AHL-51 touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called gunze. config TOUCHSCREEN_ELO tristate "Elo serial touchscreens" select SERIO help Say Y here if you have an Elo serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called elo. config TOUCHSCREEN_MTOUCH tristate "MicroTouch serial touchscreens" select SERIO help Say Y here if you have a MicroTouch (3M) serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mtouch. config TOUCHSCREEN_MK712 tristate "ICS MicroClock MK712 touchscreen" help Say Y here if you have the ICS MicroClock MK712 touchscreen controller chip in your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mk712. config TOUCHSCREEN_HP600 tristate "HP Jornada 680/690 touchscreen" depends on SH_HP6XX && SH_ADC help Say Y here if you have a HP Jornada 680 or 690 and want to support the built-in touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called hp680_ts_input. config TOUCHSCREEN_PENMOUNT tristate "Penmount serial touchscreen" select SERIO help Say Y here if you have a Penmount serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called penmount. config TOUCHSCREEN_TOUCHRIGHT tristate "Touchright serial touchscreen" select SERIO help Say Y here if you have a Touchright serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called touchright. config TOUCHSCREEN_TOUCHWIN tristate "Touchwin serial touchscreen" select SERIO help Say Y here if you have a Touchwin serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called touchwin. config TOUCHSCREEN_UCB1400 tristate "Philips UCB1400 touchscreen" select AC97_BUS help This enables support for the Philips UCB1400 touchscreen interface. The UCB1400 is an AC97 audio codec. The touchscreen interface will be initialized only after the ALSA subsystem has been brought up and the UCB1400 detected. You therefore have to configure ALSA support as well (either built-in or modular, independently of whether this driver is itself built-in or modular) for this driver to work. To compile this driver as a module, choose M here: the module will be called ucb1400_ts. config TOUCHSCREEN_USB_COMPOSITE tristate "USB Touchscreen Driver" depends on USB_ARCH_HAS_HCD select USB help USB Touchscreen driver for: - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700) - PanJit TouchSet USB - 3M MicroTouch USB (EX II series) - ITM - some other eTurboTouch - Gunze AHL61 - DMC TSC-10/25 Have a look at for a usage description and the required user-space stuff. To compile this driver as a module, choose M here: the module will be called usbtouchscreen. config TOUCHSCREEN_USB_EGALAX default y bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_PANJIT default y bool "PanJit device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_3M default y bool "3M/Microtouch EX II series device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_ITM default y bool "ITM device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_ETURBO default y bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_GUNZE default y bool "Gunze AHL61 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_DMC_TSC10 default y bool "DMC TSC-10/25 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE endif