/***********************************************************************
;*	File Name : TMSCSIM.H					       *
;*		    TEKRAM DC-390(T) PCI SCSI Bus Master Host Adapter  *
;*		    Device Driver				       *
;***********************************************************************/
/* $Id: tmscsim.h,v 2.15.2.3 2000/11/17 20:52:27 garloff Exp $ */

#ifndef _TMSCSIM_H
#define _TMSCSIM_H

#include <linux/types.h>
#include <linux/config.h>

#define SCSI_IRQ_NONE 255

#define MAX_ADAPTER_NUM 	4
#define MAX_SG_LIST_BUF 	16	/* Not used */
#define MAX_SCSI_ID		8
#define MAX_SRB_CNT		50	/* Max number of started commands */

#define SEL_TIMEOUT		153	/* 250 ms selection timeout (@ 40 MHz) */

#define pci_dma_lo32(a)			(a & 0xffffffff)

typedef u8		UCHAR;	/*  8 bits */
typedef u16		USHORT;	/* 16 bits */
typedef u32		UINT;	/* 32 bits */
typedef unsigned long	ULONG;	/* 32/64 bits */


/*
;-----------------------------------------------------------------------
; SCSI Request Block
;-----------------------------------------------------------------------
*/
struct dc390_srb
{
//u8		CmdBlock[12];

struct dc390_srb	*pNextSRB;
struct dc390_dcb	*pSRBDCB;
struct scsi_cmnd	*pcmd;
struct scatterlist	*pSegmentList;

struct scatterlist Segmentx;	/* make a one entry of S/G list table */

unsigned long	SGBusAddr;	/*;a segment starting address as seen by AM53C974A*/
unsigned long	SGToBeXferLen;	/*; to be xfer length */
unsigned long	TotalXferredLen;
unsigned long	SavedTotXLen;
unsigned long	Saved_Ptr;
u32		SRBState;

u8		SRBStatus;
u8		SRBFlag;	/*; b0-AutoReqSense,b6-Read,b7-write */
				/*; b4-settimeout,b5-Residual valid */
u8		AdaptStatus;
u8		TargetStatus;

u8		ScsiPhase;
s8		TagNumber;
u8		SGIndex;
u8		SGcount;

u8		MsgCnt;
u8		EndMessage;
u8		SavedSGCount;			

u8		MsgInBuf[6];
u8		MsgOutBuf[6];

//u8		IORBFlag;	/*;81h-Reset, 2-retry */
};


/*
;-----------------------------------------------------------------------
; Device Control Block
;-----------------------------------------------------------------------
*/
struct dc390_dcb
{
struct dc390_dcb	*pNextDCB;
struct dc390_acb	*pDCBACB;

/* Queued SRBs */
struct dc390_srb	*pGoingSRB;
struct dc390_srb	*pGoingLast;
struct dc390_srb	*pActiveSRB;
u8		GoingSRBCnt;

u32		TagMask;

u8		TargetID;	/*; SCSI Target ID  (SCSI Only) */
u8		TargetLUN;	/*; SCSI Log.  Unit (SCSI Only) */
u8		DevMode;
u8		DCBFlag;

u8		CtrlR1;
u8		CtrlR3;
u8		CtrlR4;

u8		SyncMode;	/*; 0:async mode */
u8		NegoPeriod;	/*;for nego. */
u8		SyncPeriod;	/*;for reg. */
u8		SyncOffset;	/*;for reg. and nego.(low nibble) */
};


/*
;-----------------------------------------------------------------------
; Adapter Control Block
;-----------------------------------------------------------------------
*/
struct dc390_acb
{
struct Scsi_Host *pScsiHost;
u16		IOPortBase;
u8		IRQLevel;
u8		status;

u8		SRBCount;
u8		AdapterIndex;	/*; nth Adapter this driver */
u8		DCBCnt;

u8		TagMaxNum;
u8		ACBFlag;
u8		Gmode2;
u8		scan_devices;

struct dc390_dcb	*pLinkDCB;
struct dc390_dcb	*pLastDCB;
struct dc390_dcb	*pDCBRunRobin;

struct dc390_dcb	*pActiveDCB;
struct dc390_srb	*pFreeSRB;
struct dc390_srb	*pTmpSRB;

u8		msgin123[4];
u8		Connected;
u8		pad;

#if defined(USE_SPINLOCKS) && USE_SPINLOCKS > 1 && (defined(CONFIG_SMP) || DEBUG_SPINLOCKS > 0)
spinlock_t	lock;
#endif
u8		sel_timeout;
u8		glitch_cfg;

u8		MsgLen;
u8		Ignore_IRQ;	/* Not used */

struct pci_dev	*pdev;

unsigned long	Cmds;
u32		SelLost;
u32		SelConn;
u32		CmdInQ;
u32		CmdOutOfSRB;

struct dc390_srb	TmpSRB;
struct dc390_srb	SRB_array[MAX_SRB_CNT]; 	/* 50 SRBs */
};


/*;-----------------------------------------------------------------------*/


#define BIT31	0x80000000
#define BIT30	0x40000000
#define BIT29	0x20000000
#define BIT28	0x10000000
#define BIT27	0x08000000
#define BIT26	0x04000000
#define BIT25	0x02000000
#define BIT24	0x01000000
#define BIT23	0x00800000
#define BIT22	0x00400000
#define BIT21	0x00200000
#define BIT20	0x00100000
#define BIT19	0x00080000
#define BIT18	0x00040000
#define BIT17	0x00020000
#define BIT16	0x00010000
#define BIT15	0x00008000
#define BIT14	0x00004000
#define BIT13	0x00002000
#define BIT12	0x00001000
#define BIT11	0x00000800
#define BIT10	0x00000400
#define BIT9	0x00000200
#define BIT8	0x00000100
#define BIT7	0x00000080
#define BIT6	0x00000040
#define BIT5	0x00000020
#define BIT4	0x00000010
#define BIT3	0x00000008
#define BIT2	0x00000004
#define BIT1	0x00000002
#define BIT0	0x00000001

/*;---UnitCtrlFlag */
#define UNIT_ALLOCATED	BIT0
#define UNIT_INFO_CHANGED BIT1
#define FORMATING_MEDIA BIT2
#define UNIT_RETRY	BIT3

/*;---UnitFlags */
#define DASD_SUPPORT	BIT0
#define SCSI_SUPPORT	BIT1
#define ASPI_SUPPORT	BIT2

/*;----SRBState machine definition */
#define SRB_FREE	0
#define SRB_WAIT	BIT0
#define SRB_READY	BIT1
#define SRB_MSGOUT	BIT2	/*;arbitration+msg_out 1st byte*/
#define SRB_MSGIN	BIT3
#define SRB_MSGIN_MULTI BIT4
#define SRB_COMMAND	BIT5
#define SRB_START_	BIT6	/*;arbitration+msg_out+command_out*/
#define SRB_DISCONNECT	BIT7
#define SRB_DATA_XFER	BIT8
#define SRB_XFERPAD	BIT9
#define SRB_STATUS	BIT10
#define SRB_COMPLETED	BIT11
#define SRB_ABORT_SENT	BIT12
#define DO_SYNC_NEGO	BIT13
#define SRB_UNEXPECT_RESEL BIT14

/*;---SRBstatus */
#define SRB_OK		BIT0
#define ABORTION	BIT1
#define OVER_RUN	BIT2
#define UNDER_RUN	BIT3
#define PARITY_ERROR	BIT4
#define SRB_ERROR	BIT5

/*;---ACBFlag */
#define RESET_DEV	BIT0
#define RESET_DETECT	BIT1
#define RESET_DONE	BIT2

/*;---DCBFlag */
#define ABORT_DEV_	BIT0

/*;---SRBFlag */
#define DATAOUT 	BIT7
#define DATAIN		BIT6
#define RESIDUAL_VALID	BIT5
#define ENABLE_TIMER	BIT4
#define RESET_DEV0	BIT2
#define ABORT_DEV	BIT1
#define AUTO_REQSENSE	BIT0

/*;---Adapter status */
#define H_STATUS_GOOD	 0
#define H_SEL_TIMEOUT	 0x11
#define H_OVER_UNDER_RUN 0x12
#define H_UNEXP_BUS_FREE 0x13
#define H_TARGET_PHASE_F 0x14
#define H_INVALID_CCB_OP 0x16
#define H_LINK_CCB_BAD	 0x17
#define H_BAD_TARGET_DIR 0x18
#define H_DUPLICATE_CCB  0x19
#define H_BAD_CCB_OR_SG  0x1A
#define H_ABORT 	 0x0FF

/*; SCSI Status byte codes*/ 
/* The values defined in include/scsi/scsi.h, to be shifted << 1 */

#define SCSI_STAT_UNEXP_BUS_F	0xFD	/*;  Unexpect Bus Free */
#define SCSI_STAT_BUS_RST_DETECT 0xFE	/*;  Scsi Bus Reset detected */
#define SCSI_STAT_SEL_TIMEOUT	0xFF	/*;  Selection Time out */

/* cmd->result */
#define RES_TARGET		0x000000FF	/* Target State */
#define RES_TARGET_LNX		STATUS_MASK	/* Only official ... */
#define RES_ENDMSG		0x0000FF00	/* End Message */
#define RES_DID			0x00FF0000	/* DID_ codes */
#define RES_DRV			0xFF000000	/* DRIVER_ codes */

#define MK_RES(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt))
#define MK_RES_LNX(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)<<1)

#define SET_RES_TARGET(who, tgt) do { who &= ~RES_TARGET; who |= (int)(tgt); } while (0)
#define SET_RES_TARGET_LNX(who, tgt) do { who &= ~RES_TARGET_LNX; who |= (int)(tgt) << 1; } while (0)
#define SET_RES_MSG(who, msg) do { who &= ~RES_ENDMSG; who |= (int)(msg) << 8; } while (0)
#define SET_RES_DID(who, did) do { who &= ~RES_DID; who |= (int)(did) << 16; } while (0)
#define SET_RES_DRV(who, drv) do { who &= ~RES_DRV; who |= (int)(drv) << 24; } while (0)

/*;---Sync_Mode */
#define SYNC_DISABLE	0
#define SYNC_ENABLE	BIT0
#define SYNC_NEGO_DONE	BIT1
#define WIDE_ENABLE	BIT2	/* Not used ;-) */
#define WIDE_NEGO_DONE	BIT3	/* Not used ;-) */
#define EN_TAG_QUEUEING	BIT4
#define EN_ATN_STOP	BIT5

#define SYNC_NEGO_OFFSET 15

/*;---SCSI bus phase*/
#define SCSI_DATA_OUT	0
#define SCSI_DATA_IN	1
#define SCSI_COMMAND	2
#define SCSI_STATUS_	3
#define SCSI_NOP0	4
#define SCSI_NOP1	5
#define SCSI_MSG_OUT	6
#define SCSI_MSG_IN	7

/*;----SCSI MSG BYTE*/ /* see scsi/scsi.h */ /* One is missing ! */
#define ABORT_TAG	0x0d

/*
 *	SISC query queue
 */
typedef struct {
	dma_addr_t		saved_dma_handle;
} dc390_cmd_scp_t;

/*
;==========================================================
; EEPROM byte offset
;==========================================================
*/
typedef  struct  _EEprom
{
u8	EE_MODE1;
u8	EE_SPEED;
u8	xx1;
u8	xx2;
} EEprom, *PEEprom;

#define REAL_EE_ADAPT_SCSI_ID 64
#define REAL_EE_MODE2	65
#define REAL_EE_DELAY	66
#define REAL_EE_TAG_CMD_NUM	67

#define EE_ADAPT_SCSI_ID 32
#define EE_MODE2	33
#define EE_DELAY	34
#define EE_TAG_CMD_NUM	35

#define EE_LEN		40

/*; EE_MODE1 bits definition*/
#define PARITY_CHK_	BIT0
#define SYNC_NEGO_	BIT1
#define EN_DISCONNECT_	BIT2
#define SEND_START_	BIT3
#define TAG_QUEUEING_	BIT4

/*; EE_MODE2 bits definition*/
#define MORE2_DRV	BIT0
#define GREATER_1G	BIT1
#define RST_SCSI_BUS	BIT2
#define ACTIVE_NEGATION BIT3
#define NO_SEEK 	BIT4
#define LUN_CHECK	BIT5

#define ENABLE_CE	1
#define DISABLE_CE	0
#define EEPROM_READ	0x80

/*
;==========================================================
;	AMD 53C974 Registers bit Definition
;==========================================================
*/
/*
;====================
; SCSI Register
;====================
*/

/*; Command Reg.(+0CH) (rw) */
#define DMA_COMMAND		BIT7
#define NOP_CMD 		0
#define CLEAR_FIFO_CMD		1
#define RST_DEVICE_CMD		2
#define RST_SCSI_BUS_CMD	3

#define INFO_XFER_CMD		0x10
#define INITIATOR_CMD_CMPLTE	0x11
#define MSG_ACCEPTED_CMD	0x12
#define XFER_PAD_BYTE		0x18
#define SET_ATN_CMD		0x1A
#define RESET_ATN_CMD		0x1B

#define SEL_WO_ATN		0x41	/* currently not used */
#define SEL_W_ATN		0x42
#define SEL_W_ATN_STOP		0x43
#define SEL_W_ATN3		0x46
#define EN_SEL_RESEL		0x44
#define DIS_SEL_RESEL		0x45	/* currently not used */
#define RESEL			0x40	/* " */
#define RESEL_ATN3		0x47	/* " */

#define DATA_XFER_CMD		INFO_XFER_CMD


/*; SCSI Status Reg.(+10H) (r) */
#define INTERRUPT		BIT7
#define ILLEGAL_OP_ERR		BIT6
#define PARITY_ERR		BIT5
#define COUNT_2_ZERO		BIT4
#define GROUP_CODE_VALID	BIT3
#define SCSI_PHASE_MASK 	(BIT2+BIT1+BIT0) 
/* BIT2: MSG phase; BIT1: C/D physe; BIT0: I/O phase */

/*; Interrupt Status Reg.(+14H) (r) */
#define SCSI_RESET		BIT7
#define INVALID_CMD		BIT6
#define DISCONNECTED		BIT5
#define SERVICE_REQUEST 	BIT4
#define SUCCESSFUL_OP		BIT3
#define RESELECTED		BIT2
#define SEL_ATTENTION		BIT1
#define SELECTED		BIT0

/*; Internal State Reg.(+18H) (r) */
#define SYNC_OFFSET_FLAG	BIT3
#define INTRN_STATE_MASK	(BIT2+BIT1+BIT0)
/* 0x04: Sel. successful (w/o stop), 0x01: Sel. successful (w/ stop) */

/*; Clock Factor Reg.(+24H) (w) */
#define CLK_FREQ_40MHZ		0
#define CLK_FREQ_35MHZ		(BIT2+BIT1+BIT0)
#define CLK_FREQ_30MHZ		(BIT2+BIT1)
#define CLK_FREQ_25MHZ		(BIT2+BIT0)
#define CLK_FREQ_20MHZ		BIT2
#define CLK_FREQ_15MHZ		(BIT1+BIT0)
#define CLK_FREQ_10MHZ		BIT1

/*; Control Reg. 1(+20H) (rw) */
#define EXTENDED_TIMING 	BIT7
#define DIS_INT_ON_SCSI_RST	BIT6
#define PARITY_ERR_REPO 	BIT4
#define SCSI_ID_ON_BUS		(BIT2+BIT1+BIT0) /* host adapter ID */

/*; Control Reg. 2(+2CH) (rw) */
#define EN_FEATURE		BIT6
#define EN_SCSI2_CMD		BIT3

/*; Control Reg. 3(+30H) (rw) */
#define ID_MSG_CHECK		BIT7
#define EN_QTAG_MSG		BIT6
#define EN_GRP2_CMD		BIT5
#define FAST_SCSI		BIT4	/* ;10MB/SEC */
#define FAST_CLK		BIT3	/* ;25 - 40 MHZ */

/*; Control Reg. 4(+34H) (rw) */
#define EATER_12NS		0
#define EATER_25NS		BIT7
#define EATER_35NS		BIT6
#define EATER_0NS		(BIT7+BIT6)
#define REDUCED_POWER		BIT5
#define CTRL4_RESERVED		BIT4	/* must be 1 acc. to AM53C974.c */
#define NEGATE_REQACKDATA	BIT2
#define NEGATE_REQACK		BIT3

#define GLITCH_TO_NS(x) (((~x>>6 & 2) >> 1) | ((x>>6 & 1) << 1 ^ (x>>6 & 2)))
#define NS_TO_GLITCH(y) (((~y<<7) | ~((y<<6) ^ ((y<<5 & 1<<6) | ~0x40))) & 0xc0)

/*
;====================
; DMA Register
;====================
*/
/*; DMA Command Reg.(+40H) (rw) */
#define READ_DIRECTION		BIT7
#define WRITE_DIRECTION 	0
#define EN_DMA_INT		BIT6
#define EN_PAGE_INT		BIT5	/* page transfer interrupt enable */
#define MAP_TO_MDL		BIT4
#define DIAGNOSTIC		BIT2
#define DMA_IDLE_CMD		0
#define DMA_BLAST_CMD		BIT0
#define DMA_ABORT_CMD		BIT1
#define DMA_START_CMD		(BIT1+BIT0)

/*; DMA Status Reg.(+54H) (r) */
#define PCI_MS_ABORT		BIT6
#define BLAST_COMPLETE		BIT5
#define SCSI_INTERRUPT		BIT4
#define DMA_XFER_DONE		BIT3
#define DMA_XFER_ABORT		BIT2
#define DMA_XFER_ERROR		BIT1
#define POWER_DOWN		BIT0

/*; DMA SCSI Bus and Ctrl.(+70H) */
#define EN_INT_ON_PCI_ABORT	BIT25
#define WRT_ERASE_DMA_STAT	BIT24
#define PW_DOWN_CTRL		BIT21
#define SCSI_BUSY		BIT20
#define SCLK			BIT19
#define SCAM			BIT18
#define SCSI_LINES		0x0003ffff

/*
;==========================================================
; SCSI Chip register address offset
;==========================================================
;Registers are rw unless declared otherwise 
*/
#define CtcReg_Low	0x00	/* r	curr. transfer count */
#define CtcReg_Mid	0x04	/* r */
#define CtcReg_High	0x38	/* r */
#define ScsiFifo	0x08
#define ScsiCmd 	0x0C
#define Scsi_Status	0x10	/* r */
#define INT_Status	0x14	/* r */
#define Sync_Period	0x18	/* w */
#define Sync_Offset	0x1C	/* w */
#define Clk_Factor	0x24	/* w */
#define CtrlReg1	0x20	
#define CtrlReg2	0x2C
#define CtrlReg3	0x30
#define CtrlReg4	0x34
#define DMA_Cmd 	0x40
#define DMA_XferCnt	0x44	/* rw	starting transfer count (32 bit) */
#define DMA_XferAddr	0x48	/* rw	starting physical address (32 bit) */
#define DMA_Wk_ByteCntr 0x4C	/* r	working byte counter */
#define DMA_Wk_AddrCntr 0x50	/* r	working address counter */
#define DMA_Status	0x54	/* r */
#define DMA_MDL_Addr	0x58	/* rw	starting MDL address */
#define DMA_Wk_MDL_Cntr 0x5C	/* r	working MDL counter */
#define DMA_ScsiBusCtrl 0x70	/* rw	SCSI Bus, PCI/DMA Ctrl */

#define StcReg_Low	CtcReg_Low	/* w	start transfer count */
#define StcReg_Mid	CtcReg_Mid	/* w */
#define StcReg_High	CtcReg_High	/* w */
#define Scsi_Dest_ID	Scsi_Status	/* w */
#define Scsi_TimeOut	INT_Status	/* w */
#define Intern_State	Sync_Period	/* r */
#define Current_Fifo	Sync_Offset	/* r	Curr. FIFO / int. state */


#define DC390_read8(address)			\
	(inb (pACB->IOPortBase + (address)))

#define DC390_read8_(address, base)		\
	(inb ((u16)(base) + (address)))

#define DC390_read16(address)			\
	(inw (pACB->IOPortBase + (address)))

#define DC390_read32(address)			\
	(inl (pACB->IOPortBase + (address)))

#define DC390_write8(address,value)		\
	outb ((value), pACB->IOPortBase + (address))

#define DC390_write8_(address,value,base)	\
	outb ((value), (u16)(base) + (address))

#define DC390_write16(address,value)		\
	outw ((value), pACB->IOPortBase + (address))

#define DC390_write32(address,value)		\
	outl ((value), pACB->IOPortBase + (address))


#endif /* _TMSCSIM_H */