/* * Driver for Zilog serial chips found on SGI workstations and * servers. This driver could actually be made more generic. * * This is based on the drivers/serial/sunzilog.c code as of 2.6.0-test7 and the * old drivers/sgi/char/sgiserial.c code which itself is based of the original * drivers/sbus/char/zs.c code. A lot of code has been simply moved over * directly from there but much has been rewritten. Credits therefore go out * to David S. Miller, Eddie C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell * for their work there. * * Copyright (C) 2002 Ralf Baechle (ralf@linux-mips.org) * Copyright (C) 2002 David S. Miller (davem@redhat.com) */ #include <linux/module.h> #include <linux/kernel.h> #include <linux/errno.h> #include <linux/delay.h> #include <linux/tty.h> #include <linux/tty_flip.h> #include <linux/major.h> #include <linux/string.h> #include <linux/ptrace.h> #include <linux/ioport.h> #include <linux/slab.h> #include <linux/circ_buf.h> #include <linux/serial.h> #include <linux/sysrq.h> #include <linux/console.h> #include <linux/spinlock.h> #include <linux/init.h> #include <asm/io.h> #include <asm/irq.h> #include <asm/sgialib.h> #include <asm/sgi/ioc.h> #include <asm/sgi/hpc3.h> #include <asm/sgi/ip22.h> #if defined(CONFIG_SERIAL_IP22_ZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ #endif #include <linux/serial_core.h> #include "ip22zilog.h" /* * On IP22 we need to delay after register accesses but we do not need to * flush writes. */ #define ZSDELAY() udelay(5) #define ZSDELAY_LONG() udelay(20) #define ZS_WSYNC(channel) do { } while (0) #define NUM_IP22ZILOG 1 #define NUM_CHANNELS (NUM_IP22ZILOG * 2) #define ZS_CLOCK 3672000 /* Zilog input clock rate. */ #define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */ /* * We wrap our port structure around the generic uart_port. */ struct uart_ip22zilog_port { struct uart_port port; /* IRQ servicing chain. */ struct uart_ip22zilog_port *next; /* Current values of Zilog write registers. */ unsigned char curregs[NUM_ZSREGS]; unsigned int flags; #define IP22ZILOG_FLAG_IS_CONS 0x00000004 #define IP22ZILOG_FLAG_IS_KGDB 0x00000008 #define IP22ZILOG_FLAG_MODEM_STATUS 0x00000010 #define IP22ZILOG_FLAG_IS_CHANNEL_A 0x00000020 #define IP22ZILOG_FLAG_REGS_HELD 0x00000040 #define IP22ZILOG_FLAG_TX_STOPPED 0x00000080 #define IP22ZILOG_FLAG_TX_ACTIVE 0x00000100 #define IP22ZILOG_FLAG_RESET_DONE 0x00000200 unsigned int tty_break; unsigned char parity_mask; unsigned char prev_status; }; #define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel *)((PORT)->membase)) #define UART_ZILOG(PORT) ((struct uart_ip22zilog_port *)(PORT)) #define IP22ZILOG_GET_CURR_REG(PORT, REGNUM) \ (UART_ZILOG(PORT)->curregs[REGNUM]) #define IP22ZILOG_SET_CURR_REG(PORT, REGNUM, REGVAL) \ ((UART_ZILOG(PORT)->curregs[REGNUM]) = (REGVAL)) #define ZS_IS_CONS(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CONS) #define ZS_IS_KGDB(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_KGDB) #define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & IP22ZILOG_FLAG_MODEM_STATUS) #define ZS_IS_CHANNEL_A(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CHANNEL_A) #define ZS_REGS_HELD(UP) ((UP)->flags & IP22ZILOG_FLAG_REGS_HELD) #define ZS_TX_STOPPED(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_STOPPED) #define ZS_TX_ACTIVE(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_ACTIVE) /* Reading and writing Zilog8530 registers. The delays are to make this * driver work on the IP22 which needs a settling delay after each chip * register access, other machines handle this in hardware via auxiliary * flip-flops which implement the settle time we do in software. * * The port lock must be held and local IRQs must be disabled * when {read,write}_zsreg is invoked. */ static unsigned char read_zsreg(struct zilog_channel *channel, unsigned char reg) { unsigned char retval; writeb(reg, &channel->control); ZSDELAY(); retval = readb(&channel->control); ZSDELAY(); return retval; } static void write_zsreg(struct zilog_channel *channel, unsigned char reg, unsigned char value) { writeb(reg, &channel->control); ZSDELAY(); writeb(value, &channel->control); ZSDELAY(); } static void ip22zilog_clear_fifo(struct zilog_channel *channel) { int i; for (i = 0; i < 32; i++) { unsigned char regval; regval = readb(&channel->control); ZSDELAY(); if (regval & Rx_CH_AV) break; regval = read_zsreg(channel, R1); readb(&channel->data); ZSDELAY(); if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) { writeb(ERR_RES, &channel->control); ZSDELAY(); ZS_WSYNC(channel); } } } /* This function must only be called when the TX is not busy. The UART * port lock must be held and local interrupts disabled. */ static void __load_zsregs(struct zilog_channel *channel, unsigned char *regs) { int i; /* Let pending transmits finish. */ for (i = 0; i < 1000; i++) { unsigned char stat = read_zsreg(channel, R1); if (stat & ALL_SNT) break; udelay(100); } writeb(ERR_RES, &channel->control); ZSDELAY(); ZS_WSYNC(channel); ip22zilog_clear_fifo(channel); /* Disable all interrupts. */ write_zsreg(channel, R1, regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB)); /* Set parity, sync config, stop bits, and clock divisor. */ write_zsreg(channel, R4, regs[R4]); /* Set misc. TX/RX control bits. */ write_zsreg(channel, R10, regs[R10]); /* Set TX/RX controls sans the enable bits. */ write_zsreg(channel, R3, regs[R3] & ~RxENAB); write_zsreg(channel, R5, regs[R5] & ~TxENAB); /* Synchronous mode config. */ write_zsreg(channel, R6, regs[R6]); write_zsreg(channel, R7, regs[R7]); /* Don't mess with the interrupt vector (R2, unused by us) and * master interrupt control (R9). We make sure this is setup * properly at probe time then never touch it again. */ /* Disable baud generator. */ write_zsreg(channel, R14, regs[R14] & ~BRENAB); /* Clock mode control. */ write_zsreg(channel, R11, regs[R11]); /* Lower and upper byte of baud rate generator divisor. */ write_zsreg(channel, R12, regs[R12]); write_zsreg(channel, R13, regs[R13]); /* Now rewrite R14, with BRENAB (if set). */ write_zsreg(channel, R14, regs[R14]); /* External status interrupt control. */ write_zsreg(channel, R15, regs[R15]); /* Reset external status interrupts. */ write_zsreg(channel, R0, RES_EXT_INT); write_zsreg(channel, R0, RES_EXT_INT); /* Rewrite R3/R5, this time without enables masked. */ write_zsreg(channel, R3, regs[R3]); write_zsreg(channel, R5, regs[R5]); /* Rewrite R1, this time without IRQ enabled masked. */ write_zsreg(channel, R1, regs[R1]); } /* Reprogram the Zilog channel HW registers with the copies found in the * software state struct. If the transmitter is busy, we defer this update * until the next TX complete interrupt. Else, we do it right now. * * The UART port lock must be held and local interrupts disabled. */ static void ip22zilog_maybe_update_regs(struct uart_ip22zilog_port *up, struct zilog_channel *channel) { if (!ZS_REGS_HELD(up)) { if (ZS_TX_ACTIVE(up)) { up->flags |= IP22ZILOG_FLAG_REGS_HELD; } else { __load_zsregs(channel, up->curregs); } } } #define Rx_BRK 0x0100 /* BREAK event software flag. */ #define Rx_SYS 0x0200 /* SysRq event software flag. */ static struct tty_struct *ip22zilog_receive_chars(struct uart_ip22zilog_port *up, struct zilog_channel *channel) { struct tty_struct *tty; unsigned char ch, flag; unsigned int r1; tty = NULL; if (up->port.info != NULL && up->port.info->tty != NULL) tty = up->port.info->tty; for (;;) { ch = readb(&channel->control); ZSDELAY(); if (!(ch & Rx_CH_AV)) break; r1 = read_zsreg(channel, R1); if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { writeb(ERR_RES, &channel->control); ZSDELAY(); ZS_WSYNC(channel); } ch = readb(&channel->data); ZSDELAY(); ch &= up->parity_mask; /* Handle the null char got when BREAK is removed. */ if (!ch) r1 |= up->tty_break; /* A real serial line, record the character and status. */ flag = TTY_NORMAL; up->port.icount.rx++; if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | Rx_SYS | Rx_BRK)) { up->tty_break = 0; if (r1 & (Rx_SYS | Rx_BRK)) { up->port.icount.brk++; if (r1 & Rx_SYS) continue; r1 &= ~(PAR_ERR | CRC_ERR); } else if (r1 & PAR_ERR) up->port.icount.parity++; else if (r1 & CRC_ERR) up->port.icount.frame++; if (r1 & Rx_OVR) up->port.icount.overrun++; r1 &= up->port.read_status_mask; if (r1 & Rx_BRK) flag = TTY_BREAK; else if (r1 & PAR_ERR) flag = TTY_PARITY; else if (r1 & CRC_ERR) flag = TTY_FRAME; } if (uart_handle_sysrq_char(&up->port, ch)) continue; if (tty) uart_insert_char(&up->port, r1, Rx_OVR, ch, flag); } return tty; } static void ip22zilog_status_handle(struct uart_ip22zilog_port *up, struct zilog_channel *channel) { unsigned char status; status = readb(&channel->control); ZSDELAY(); writeb(RES_EXT_INT, &channel->control); ZSDELAY(); ZS_WSYNC(channel); if (up->curregs[R15] & BRKIE) { if ((status & BRK_ABRT) && !(up->prev_status & BRK_ABRT)) { if (uart_handle_break(&up->port)) up->tty_break = Rx_SYS; else up->tty_break = Rx_BRK; } } if (ZS_WANTS_MODEM_STATUS(up)) { if (status & SYNC) up->port.icount.dsr++; /* The Zilog just gives us an interrupt when DCD/CTS/etc. change. * But it does not tell us which bit has changed, we have to keep * track of this ourselves. */ if ((status ^ up->prev_status) ^ DCD) uart_handle_dcd_change(&up->port, (status & DCD)); if ((status ^ up->prev_status) ^ CTS) uart_handle_cts_change(&up->port, (status & CTS)); wake_up_interruptible(&up->port.info->delta_msr_wait); } up->prev_status = status; } static void ip22zilog_transmit_chars(struct uart_ip22zilog_port *up, struct zilog_channel *channel) { struct circ_buf *xmit; if (ZS_IS_CONS(up)) { unsigned char status = readb(&channel->control); ZSDELAY(); /* TX still busy? Just wait for the next TX done interrupt. * * It can occur because of how we do serial console writes. It would * be nice to transmit console writes just like we normally would for * a TTY line. (ie. buffered and TX interrupt driven). That is not * easy because console writes cannot sleep. One solution might be * to poll on enough port->xmit space becomming free. -DaveM */ if (!(status & Tx_BUF_EMP)) return; } up->flags &= ~IP22ZILOG_FLAG_TX_ACTIVE; if (ZS_REGS_HELD(up)) { __load_zsregs(channel, up->curregs); up->flags &= ~IP22ZILOG_FLAG_REGS_HELD; } if (ZS_TX_STOPPED(up)) { up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED; goto ack_tx_int; } if (up->port.x_char) { up->flags |= IP22ZILOG_FLAG_TX_ACTIVE; writeb(up->port.x_char, &channel->data); ZSDELAY(); ZS_WSYNC(channel); up->port.icount.tx++; up->port.x_char = 0; return; } if (up->port.info == NULL) goto ack_tx_int; xmit = &up->port.info->xmit; if (uart_circ_empty(xmit)) goto ack_tx_int; if (uart_tx_stopped(&up->port)) goto ack_tx_int; up->flags |= IP22ZILOG_FLAG_TX_ACTIVE; writeb(xmit->buf[xmit->tail], &channel->data); ZSDELAY(); ZS_WSYNC(channel); xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); up->port.icount.tx++; if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) uart_write_wakeup(&up->port); return; ack_tx_int: writeb(RES_Tx_P, &channel->control); ZSDELAY(); ZS_WSYNC(channel); } static irqreturn_t ip22zilog_interrupt(int irq, void *dev_id) { struct uart_ip22zilog_port *up = dev_id; while (up) { struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(&up->port); struct tty_struct *tty; unsigned char r3; spin_lock(&up->port.lock); r3 = read_zsreg(channel, R3); /* Channel A */ tty = NULL; if (r3 & (CHAEXT | CHATxIP | CHARxIP)) { writeb(RES_H_IUS, &channel->control); ZSDELAY(); ZS_WSYNC(channel); if (r3 & CHARxIP) tty = ip22zilog_receive_chars(up, channel); if (r3 & CHAEXT) ip22zilog_status_handle(up, channel); if (r3 & CHATxIP) ip22zilog_transmit_chars(up, channel); } spin_unlock(&up->port.lock); if (tty) tty_flip_buffer_push(tty); /* Channel B */ up = up->next; channel = ZILOG_CHANNEL_FROM_PORT(&up->port); spin_lock(&up->port.lock); tty = NULL; if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) { writeb(RES_H_IUS, &channel->control); ZSDELAY(); ZS_WSYNC(channel); if (r3 & CHBRxIP) tty = ip22zilog_receive_chars(up, channel); if (r3 & CHBEXT) ip22zilog_status_handle(up, channel); if (r3 & CHBTxIP) ip22zilog_transmit_chars(up, channel); } spin_unlock(&up->port.lock); if (tty) tty_flip_buffer_push(tty); up = up->next; } return IRQ_HANDLED; } /* A convenient way to quickly get R0 status. The caller must _not_ hold the * port lock, it is acquired here. */ static __inline__ unsigned char ip22zilog_read_channel_status(struct uart_port *port) { struct zilog_channel *channel; unsigned char status; channel = ZILOG_CHANNEL_FROM_PORT(port); status = readb(&channel->control); ZSDELAY(); return status; } /* The port lock is not held. */ static unsigned int ip22zilog_tx_empty(struct uart_port *port) { unsigned long flags; unsigned char status; unsigned int ret; spin_lock_irqsave(&port->lock, flags); status = ip22zilog_read_channel_status(port); spin_unlock_irqrestore(&port->lock, flags); if (status & Tx_BUF_EMP) ret = TIOCSER_TEMT; else ret = 0; return ret; } /* The port lock is held and interrupts are disabled. */ static unsigned int ip22zilog_get_mctrl(struct uart_port *port) { unsigned char status; unsigned int ret; status = ip22zilog_read_channel_status(port); ret = 0; if (status & DCD) ret |= TIOCM_CAR; if (status & SYNC) ret |= TIOCM_DSR; if (status & CTS) ret |= TIOCM_CTS; return ret; } /* The port lock is held and interrupts are disabled. */ static void ip22zilog_set_mctrl(struct uart_port *port, unsigned int mctrl) { struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port; struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port); unsigned char set_bits, clear_bits; set_bits = clear_bits = 0; if (mctrl & TIOCM_RTS) set_bits |= RTS; else clear_bits |= RTS; if (mctrl & TIOCM_DTR) set_bits |= DTR; else clear_bits |= DTR; /* NOTE: Not subject to 'transmitter active' rule. */ up->curregs[R5] |= set_bits; up->curregs[R5] &= ~clear_bits; write_zsreg(channel, R5, up->curregs[R5]); } /* The port lock is held and interrupts are disabled. */ static void ip22zilog_stop_tx(struct uart_port *port) { struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port; up->flags |= IP22ZILOG_FLAG_TX_STOPPED; } /* The port lock is held and interrupts are disabled. */ static void ip22zilog_start_tx(struct uart_port *port) { struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port; struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port); unsigned char status; up->flags |= IP22ZILOG_FLAG_TX_ACTIVE; up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED; status = readb(&channel->control); ZSDELAY(); /* TX busy? Just wait for the TX done interrupt. */ if (!(status & Tx_BUF_EMP)) return; /* Send the first character to jump-start the TX done * IRQ sending engine. */ if (port->x_char) { writeb(port->x_char, &channel->data); ZSDELAY(); ZS_WSYNC(channel); port->icount.tx++; port->x_char = 0; } else { struct circ_buf *xmit = &port->info->xmit; writeb(xmit->buf[xmit->tail], &channel->data); ZSDELAY(); ZS_WSYNC(channel); xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); port->icount.tx++; if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) uart_write_wakeup(&up->port); } } /* The port lock is held and interrupts are disabled. */ static void ip22zilog_stop_rx(struct uart_port *port) { struct uart_ip22zilog_port *up = UART_ZILOG(port); struct zilog_channel *channel; if (ZS_IS_CONS(up)) return; channel = ZILOG_CHANNEL_FROM_PORT(port); /* Disable all RX interrupts. */ up->curregs[R1] &= ~RxINT_MASK; ip22zilog_maybe_update_regs(up, channel); } /* The port lock is held. */ static void ip22zilog_enable_ms(struct uart_port *port) { struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port; struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port); unsigned char new_reg; new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE); if (new_reg != up->curregs[R15]) { up->curregs[R15] = new_reg; /* NOTE: Not subject to 'transmitter active' rule. */ write_zsreg(channel, R15, up->curregs[R15]); } } /* The port lock is not held. */ static void ip22zilog_break_ctl(struct uart_port *port, int break_state) { struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port; struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port); unsigned char set_bits, clear_bits, new_reg; unsigned long flags; set_bits = clear_bits = 0; if (break_state) set_bits |= SND_BRK; else clear_bits |= SND_BRK; spin_lock_irqsave(&port->lock, flags); new_reg = (up->curregs[R5] | set_bits) & ~clear_bits; if (new_reg != up->curregs[R5]) { up->curregs[R5] = new_reg; /* NOTE: Not subject to 'transmitter active' rule. */ write_zsreg(channel, R5, up->curregs[R5]); } spin_unlock_irqrestore(&port->lock, flags); } static void __ip22zilog_reset(struct uart_ip22zilog_port *up) { struct zilog_channel *channel; int i; if (up->flags & IP22ZILOG_FLAG_RESET_DONE) return; /* Let pending transmits finish. */ channel = ZILOG_CHANNEL_FROM_PORT(&up->port); for (i = 0; i < 1000; i++) { unsigned char stat = read_zsreg(channel, R1); if (stat & ALL_SNT) break; udelay(100); } if (!ZS_IS_CHANNEL_A(up)) { up++; channel = ZILOG_CHANNEL_FROM_PORT(&up->port); } write_zsreg(channel, R9, FHWRES); ZSDELAY_LONG(); (void) read_zsreg(channel, R0); up->flags |= IP22ZILOG_FLAG_RESET_DONE; up->next->flags |= IP22ZILOG_FLAG_RESET_DONE; } static void __ip22zilog_startup(struct uart_ip22zilog_port *up) { struct zilog_channel *channel; channel = ZILOG_CHANNEL_FROM_PORT(&up->port); __ip22zilog_reset(up); __load_zsregs(channel, up->curregs); /* set master interrupt enable */ write_zsreg(channel, R9, up->curregs[R9]); up->prev_status = readb(&channel->control); /* Enable receiver and transmitter. */ up->curregs[R3] |= RxENAB; up->curregs[R5] |= TxENAB; up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; ip22zilog_maybe_update_regs(up, channel); } static int ip22zilog_startup(struct uart_port *port) { struct uart_ip22zilog_port *up = UART_ZILOG(port); unsigned long flags; if (ZS_IS_CONS(up)) return 0; spin_lock_irqsave(&port->lock, flags); __ip22zilog_startup(up); spin_unlock_irqrestore(&port->lock, flags); return 0; } /* * The test for ZS_IS_CONS is explained by the following e-mail: ***** * From: Russell King <rmk@arm.linux.org.uk> * Date: Sun, 8 Dec 2002 10:18:38 +0000 * * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote: * > I boot my 2.5 boxes using "console=ttyS0,9600" argument, * > and I noticed that something is not right with reference * > counting in this case. It seems that when the console * > is open by kernel initially, this is not accounted * > as an open, and uart_startup is not called. * * That is correct. We are unable to call uart_startup when the serial * console is initialised because it may need to allocate memory (as * request_irq does) and the memory allocators may not have been * initialised. * * 1. initialise the port into a state where it can send characters in the * console write method. * * 2. don't do the actual hardware shutdown in your shutdown() method (but * do the normal software shutdown - ie, free irqs etc) ***** */ static void ip22zilog_shutdown(struct uart_port *port) { struct uart_ip22zilog_port *up = UART_ZILOG(port); struct zilog_channel *channel; unsigned long flags; if (ZS_IS_CONS(up)) return; spin_lock_irqsave(&port->lock, flags); channel = ZILOG_CHANNEL_FROM_PORT(port); /* Disable receiver and transmitter. */ up->curregs[R3] &= ~RxENAB; up->curregs[R5] &= ~TxENAB; /* Disable all interrupts and BRK assertion. */ up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK); up->curregs[R5] &= ~SND_BRK; ip22zilog_maybe_update_regs(up, channel); spin_unlock_irqrestore(&port->lock, flags); } /* Shared by TTY driver and serial console setup. The port lock is held * and local interrupts are disabled. */ static void ip22zilog_convert_to_zs(struct uart_ip22zilog_port *up, unsigned int cflag, unsigned int iflag, int brg) { up->curregs[R10] = NRZ; up->curregs[R11] = TCBR | RCBR; /* Program BAUD and clock source. */ up->curregs[R4] &= ~XCLK_MASK; up->curregs[R4] |= X16CLK; up->curregs[R12] = brg & 0xff; up->curregs[R13] = (brg >> 8) & 0xff; up->curregs[R14] = BRENAB; /* Character size, stop bits, and parity. */ up->curregs[3] &= ~RxN_MASK; up->curregs[5] &= ~TxN_MASK; switch (cflag & CSIZE) { case CS5: up->curregs[3] |= Rx5; up->curregs[5] |= Tx5; up->parity_mask = 0x1f; break; case CS6: up->curregs[3] |= Rx6; up->curregs[5] |= Tx6; up->parity_mask = 0x3f; break; case CS7: up->curregs[3] |= Rx7; up->curregs[5] |= Tx7; up->parity_mask = 0x7f; break; case CS8: default: up->curregs[3] |= Rx8; up->curregs[5] |= Tx8; up->parity_mask = 0xff; break; }; up->curregs[4] &= ~0x0c; if (cflag & CSTOPB) up->curregs[4] |= SB2; else up->curregs[4] |= SB1; if (cflag & PARENB) up->curregs[4] |= PAR_ENAB; else up->curregs[4] &= ~PAR_ENAB; if (!(cflag & PARODD)) up->curregs[4] |= PAR_EVEN; else up->curregs[4] &= ~PAR_EVEN; up->port.read_status_mask = Rx_OVR; if (iflag & INPCK) up->port.read_status_mask |= CRC_ERR | PAR_ERR; if (iflag & (BRKINT | PARMRK)) up->port.read_status_mask |= BRK_ABRT; up->port.ignore_status_mask = 0; if (iflag & IGNPAR) up->port.ignore_status_mask |= CRC_ERR | PAR_ERR; if (iflag & IGNBRK) { up->port.ignore_status_mask |= BRK_ABRT; if (iflag & IGNPAR) up->port.ignore_status_mask |= Rx_OVR; } if ((cflag & CREAD) == 0) up->port.ignore_status_mask = 0xff; } /* The port lock is not held. */ static void ip22zilog_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port; unsigned long flags; int baud, brg; baud = uart_get_baud_rate(port, termios, old, 1200, 76800); spin_lock_irqsave(&up->port.lock, flags); brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); ip22zilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg); if (UART_ENABLE_MS(&up->port, termios->c_cflag)) up->flags |= IP22ZILOG_FLAG_MODEM_STATUS; else up->flags &= ~IP22ZILOG_FLAG_MODEM_STATUS; ip22zilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port)); uart_update_timeout(port, termios->c_cflag, baud); spin_unlock_irqrestore(&up->port.lock, flags); } static const char *ip22zilog_type(struct uart_port *port) { return "IP22-Zilog"; } /* We do not request/release mappings of the registers here, this * happens at early serial probe time. */ static void ip22zilog_release_port(struct uart_port *port) { } static int ip22zilog_request_port(struct uart_port *port) { return 0; } /* These do not need to do anything interesting either. */ static void ip22zilog_config_port(struct uart_port *port, int flags) { } /* We do not support letting the user mess with the divisor, IRQ, etc. */ static int ip22zilog_verify_port(struct uart_port *port, struct serial_struct *ser) { return -EINVAL; } static struct uart_ops ip22zilog_pops = { .tx_empty = ip22zilog_tx_empty, .set_mctrl = ip22zilog_set_mctrl, .get_mctrl = ip22zilog_get_mctrl, .stop_tx = ip22zilog_stop_tx, .start_tx = ip22zilog_start_tx, .stop_rx = ip22zilog_stop_rx, .enable_ms = ip22zilog_enable_ms, .break_ctl = ip22zilog_break_ctl, .startup = ip22zilog_startup, .shutdown = ip22zilog_shutdown, .set_termios = ip22zilog_set_termios, .type = ip22zilog_type, .release_port = ip22zilog_release_port, .request_port = ip22zilog_request_port, .config_port = ip22zilog_config_port, .verify_port = ip22zilog_verify_port, }; static struct uart_ip22zilog_port *ip22zilog_port_table; static struct zilog_layout **ip22zilog_chip_regs; static struct uart_ip22zilog_port *ip22zilog_irq_chain; static int zilog_irq = -1; static void * __init alloc_one_table(unsigned long size) { return kzalloc(size, GFP_KERNEL); } static void __init ip22zilog_alloc_tables(void) { ip22zilog_port_table = (struct uart_ip22zilog_port *) alloc_one_table(NUM_CHANNELS * sizeof(struct uart_ip22zilog_port)); ip22zilog_chip_regs = (struct zilog_layout **) alloc_one_table(NUM_IP22ZILOG * sizeof(struct zilog_layout *)); if (ip22zilog_port_table == NULL || ip22zilog_chip_regs == NULL) { panic("IP22-Zilog: Cannot allocate IP22-Zilog tables."); } } /* Get the address of the registers for IP22-Zilog instance CHIP. */ static struct zilog_layout * __init get_zs(int chip) { unsigned long base; if (chip < 0 || chip >= NUM_IP22ZILOG) { panic("IP22-Zilog: Illegal chip number %d in get_zs.", chip); } /* Not probe-able, hard code it. */ base = (unsigned long) &sgioc->uart; zilog_irq = SGI_SERIAL_IRQ; request_mem_region(base, 8, "IP22-Zilog"); return (struct zilog_layout *) base; } #define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */ #ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE static void ip22zilog_put_char(struct uart_port *port, int ch) { struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port); int loops = ZS_PUT_CHAR_MAX_DELAY; /* This is a timed polling loop so do not switch the explicit * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM */ do { unsigned char val = readb(&channel->control); if (val & Tx_BUF_EMP) { ZSDELAY(); break; } udelay(5); } while (--loops); writeb(ch, &channel->data); ZSDELAY(); ZS_WSYNC(channel); } static void ip22zilog_console_write(struct console *con, const char *s, unsigned int count) { struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index]; unsigned long flags; spin_lock_irqsave(&up->port.lock, flags); uart_console_write(&up->port, s, count, ip22zilog_put_char); udelay(2); spin_unlock_irqrestore(&up->port.lock, flags); } static int __init ip22zilog_console_setup(struct console *con, char *options) { struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index]; unsigned long flags; int baud = 9600, bits = 8; int parity = 'n'; int flow = 'n'; up->flags |= IP22ZILOG_FLAG_IS_CONS; printk(KERN_INFO "Console: ttyS%d (IP22-Zilog)\n", con->index); spin_lock_irqsave(&up->port.lock, flags); up->curregs[R15] |= BRKIE; __ip22zilog_startup(up); spin_unlock_irqrestore(&up->port.lock, flags); if (options) uart_parse_options(options, &baud, &parity, &bits, &flow); return uart_set_options(&up->port, con, baud, parity, bits, flow); } static struct uart_driver ip22zilog_reg; static struct console ip22zilog_console = { .name = "ttyS", .write = ip22zilog_console_write, .device = uart_console_device, .setup = ip22zilog_console_setup, .flags = CON_PRINTBUFFER, .index = -1, .data = &ip22zilog_reg, }; #endif /* CONFIG_SERIAL_IP22_ZILOG_CONSOLE */ static struct uart_driver ip22zilog_reg = { .owner = THIS_MODULE, .driver_name = "serial", .dev_name = "ttyS", .major = TTY_MAJOR, .minor = 64, .nr = NUM_CHANNELS, #ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE .cons = &ip22zilog_console, #endif }; static void __init ip22zilog_prepare(void) { struct uart_ip22zilog_port *up; struct zilog_layout *rp; int channel, chip; /* * Temporary fix. */ for (channel = 0; channel < NUM_CHANNELS; channel++) spin_lock_init(&ip22zilog_port_table[channel].port.lock); ip22zilog_irq_chain = &ip22zilog_port_table[NUM_CHANNELS - 1]; up = &ip22zilog_port_table[0]; for (channel = NUM_CHANNELS - 1 ; channel > 0; channel--) up[channel].next = &up[channel - 1]; up[channel].next = NULL; for (chip = 0; chip < NUM_IP22ZILOG; chip++) { if (!ip22zilog_chip_regs[chip]) { ip22zilog_chip_regs[chip] = rp = get_zs(chip); up[(chip * 2) + 0].port.membase = (char *) &rp->channelB; up[(chip * 2) + 1].port.membase = (char *) &rp->channelA; /* In theory mapbase is the physical address ... */ up[(chip * 2) + 0].port.mapbase = (unsigned long) ioremap((unsigned long) &rp->channelB, 8); up[(chip * 2) + 1].port.mapbase = (unsigned long) ioremap((unsigned long) &rp->channelA, 8); } /* Channel A */ up[(chip * 2) + 0].port.iotype = UPIO_MEM; up[(chip * 2) + 0].port.irq = zilog_irq; up[(chip * 2) + 0].port.uartclk = ZS_CLOCK; up[(chip * 2) + 0].port.fifosize = 1; up[(chip * 2) + 0].port.ops = &ip22zilog_pops; up[(chip * 2) + 0].port.type = PORT_IP22ZILOG; up[(chip * 2) + 0].port.flags = 0; up[(chip * 2) + 0].port.line = (chip * 2) + 0; up[(chip * 2) + 0].flags = 0; /* Channel B */ up[(chip * 2) + 1].port.iotype = UPIO_MEM; up[(chip * 2) + 1].port.irq = zilog_irq; up[(chip * 2) + 1].port.uartclk = ZS_CLOCK; up[(chip * 2) + 1].port.fifosize = 1; up[(chip * 2) + 1].port.ops = &ip22zilog_pops; up[(chip * 2) + 1].port.type = PORT_IP22ZILOG; up[(chip * 2) + 1].port.line = (chip * 2) + 1; up[(chip * 2) + 1].flags |= IP22ZILOG_FLAG_IS_CHANNEL_A; } for (channel = 0; channel < NUM_CHANNELS; channel++) { struct uart_ip22zilog_port *up = &ip22zilog_port_table[channel]; int brg; /* Normal serial TTY. */ up->parity_mask = 0xff; up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; up->curregs[R4] = PAR_EVEN | X16CLK | SB1; up->curregs[R3] = RxENAB | Rx8; up->curregs[R5] = TxENAB | Tx8; up->curregs[R9] = NV | MIE; up->curregs[R10] = NRZ; up->curregs[R11] = TCBR | RCBR; brg = BPS_TO_BRG(9600, ZS_CLOCK / ZS_CLOCK_DIVISOR); up->curregs[R12] = (brg & 0xff); up->curregs[R13] = (brg >> 8) & 0xff; up->curregs[R14] = BRENAB; } } static int __init ip22zilog_ports_init(void) { int ret; printk(KERN_INFO "Serial: IP22 Zilog driver (%d chips).\n", NUM_IP22ZILOG); ip22zilog_prepare(); if (request_irq(zilog_irq, ip22zilog_interrupt, 0, "IP22-Zilog", ip22zilog_irq_chain)) { panic("IP22-Zilog: Unable to register zs interrupt handler.\n"); } ret = uart_register_driver(&ip22zilog_reg); if (ret == 0) { int i; for (i = 0; i < NUM_CHANNELS; i++) { struct uart_ip22zilog_port *up = &ip22zilog_port_table[i]; uart_add_one_port(&ip22zilog_reg, &up->port); } } return ret; } static int __init ip22zilog_init(void) { /* IP22 Zilog setup is hard coded, no probing to do. */ ip22zilog_alloc_tables(); ip22zilog_ports_init(); return 0; } static void __exit ip22zilog_exit(void) { int i; struct uart_ip22zilog_port *up; for (i = 0; i < NUM_CHANNELS; i++) { up = &ip22zilog_port_table[i]; uart_remove_one_port(&ip22zilog_reg, &up->port); } /* Free IO mem */ up = &ip22zilog_port_table[0]; for (i = 0; i < NUM_IP22ZILOG; i++) { if (up[(i * 2) + 0].port.mapbase) { iounmap((void*)up[(i * 2) + 0].port.mapbase); up[(i * 2) + 0].port.mapbase = 0; } if (up[(i * 2) + 1].port.mapbase) { iounmap((void*)up[(i * 2) + 1].port.mapbase); up[(i * 2) + 1].port.mapbase = 0; } } uart_unregister_driver(&ip22zilog_reg); } module_init(ip22zilog_init); module_exit(ip22zilog_exit); /* David wrote it but I'm to blame for the bugs ... */ MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>"); MODULE_DESCRIPTION("SGI Zilog serial port driver"); MODULE_LICENSE("GPL");