/* * Digi AccelePort USB-4 and USB-2 Serial Converters * * Copyright 2000 by Digi International * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's * usb-serial driver. * * Peter Berger (pberger@brimson.com) * Al Borchers (borchers@steinerpoint.com) * * (12/03/2001) gkh * switched to using port->open_count instead of private version. * Removed port->active * * (04/08/2001) gb * Identify version on module load. * * (11/01/2000) Adam J. Richter * usb_device_id table support * * (11/01/2000) pberger and borchers * -- Turned off the USB_DISABLE_SPD flag for write bulk urbs--it caused * USB 4 ports to hang on startup. * -- Serialized access to write urbs by adding the dp_write_urb_in_use * flag; otherwise, the driver caused SMP system hangs. Watching the * urb status is not sufficient. * * (10/05/2000) gkh * -- Fixed bug with urb->dev not being set properly, now that the usb * core needs it. * * (8/8/2000) pberger and borchers * -- Fixed close so that * - it can timeout while waiting for transmit idle, if needed; * - it ignores interrupts when flushing the port, turning * of modem signalling, and so on; * - it waits for the flush to really complete before returning. * -- Read_bulk_callback and write_bulk_callback check for a closed * port before using the tty struct or writing to the port. * -- The two changes above fix the oops caused by interrupted closes. * -- Added interruptible args to write_oob_command and set_modem_signals * and added a timeout arg to transmit_idle; needed for fixes to * close. * -- Added code for rx_throttle and rx_unthrottle so that input flow * control works. * -- Added code to set overrun, parity, framing, and break errors * (untested). * -- Set USB_DISABLE_SPD flag for write bulk urbs, so no 0 length * bulk writes are done. These hung the Digi USB device. The * 0 length bulk writes were a new feature of usb-uhci added in * the 2.4.0-test6 kernels. * -- Fixed mod inc race in open; do mod inc before sleeping to wait * for a close to finish. * * (7/31/2000) pberger * -- Fixed bugs with hardware handshaking: * - Added code to set/clear tty->hw_stopped in digi_read_oob_callback() * and digi_set_termios() * -- Added code in digi_set_termios() to * - add conditional in code handling transition from B0 to only * set RTS if RTS/CTS flow control is either not in use or if * the port is not currently throttled. * - handle turning off CRTSCTS. * * (7/30/2000) borchers * -- Added support for more than one Digi USB device by moving * globals to a private structure in the pointed to from the * usb_serial structure. * -- Moved the modem change and transmit idle wait queues into * the port private structure, so each port has its own queue * rather than sharing global queues. * -- Added support for break signals. * * (7/25/2000) pberger * -- Added USB-2 support. Note: the USB-2 supports 3 devices: two * serial and a parallel port. The parallel port is implemented * as a serial-to-parallel converter. That is, the driver actually * presents all three USB-2 interfaces as serial ports, but the third * one physically connects to a parallel device. Thus, for example, * one could plug a parallel printer into the USB-2's third port, * but from the kernel's (and userland's) point of view what's * actually out there is a serial device. * * (7/15/2000) borchers * -- Fixed race in open when a close is in progress. * -- Keep count of opens and dec the module use count for each * outstanding open when shutdown is called (on disconnect). * -- Fixed sanity checks in read_bulk_callback and write_bulk_callback * so pointers are checked before use. * -- Split read bulk callback into in band and out of band * callbacks, and no longer restart read chains if there is * a status error or a sanity error. This fixed the seg * faults and other errors we used to get on disconnect. * -- Port->active is once again a flag as usb-serial intended it * to be, not a count. Since it was only a char it would * have been limited to 256 simultaneous opens. Now the open * count is kept in the port private structure in dp_open_count. * -- Added code for modularization of the digi_acceleport driver. * * (6/27/2000) pberger and borchers * -- Zeroed out sync field in the wakeup_task before first use; * otherwise the uninitialized value might prevent the task from * being scheduled. * -- Initialized ret value to 0 in write_bulk_callback, otherwise * the uninitialized value could cause a spurious debugging message. * * (6/22/2000) pberger and borchers * -- Made cond_wait_... inline--apparently on SPARC the flags arg * to spin_lock_irqsave cannot be passed to another function * to call spin_unlock_irqrestore. Thanks to Pauline Middelink. * -- In digi_set_modem_signals the inner nested spin locks use just * spin_lock() rather than spin_lock_irqsave(). The old code * mistakenly left interrupts off. Thanks to Pauline Middelink. * -- copy_from_user (which can sleep) is no longer called while a * spinlock is held. We copy to a local buffer before getting * the spinlock--don't like the extra copy but the code is simpler. * -- Printk and dbg are no longer called while a spin lock is held. * * (6/4/2000) pberger and borchers * -- Replaced separate calls to spin_unlock_irqrestore and * interruptible_sleep_on_timeout with a new function * cond_wait_interruptible_timeout_irqrestore. This eliminates * the race condition where the wake up could happen after * the unlock and before the sleep. * -- Close now waits for output to drain. * -- Open waits until any close in progress is finished. * -- All out of band responses are now processed, not just the * first in a USB packet. * -- Fixed a bug that prevented the driver from working when the * first Digi port was not the first USB serial port--the driver * was mistakenly using the external USB serial port number to * try to index into its internal ports. * -- Fixed an SMP bug -- write_bulk_callback is called directly from * an interrupt, so spin_lock_irqsave/spin_unlock_irqrestore are * needed for locks outside write_bulk_callback that are also * acquired by write_bulk_callback to prevent deadlocks. * -- Fixed support for select() by making digi_chars_in_buffer() * return 256 when -EINPROGRESS is set, as the line discipline * code in n_tty.c expects. * -- Fixed an include file ordering problem that prevented debugging * messages from working. * -- Fixed an intermittent timeout problem that caused writes to * sometimes get stuck on some machines on some kernels. It turns * out in these circumstances write_chan() (in n_tty.c) was * asleep waiting for our wakeup call. Even though we call * wake_up_interruptible() in digi_write_bulk_callback(), there is * a race condition that could cause the wakeup to fail: if our * wake_up_interruptible() call occurs between the time that our * driver write routine finishes and write_chan() sets current->state * to TASK_INTERRUPTIBLE, the effect of our wakeup setting the state * to TASK_RUNNING will be lost and write_chan's subsequent call to * schedule() will never return (unless it catches a signal). * This race condition occurs because write_bulk_callback() (and thus * the wakeup) are called asynchronously from an interrupt, rather than * from the scheduler. We can avoid the race by calling the wakeup * from the scheduler queue and that's our fix: Now, at the end of * write_bulk_callback() we queue up a wakeup call on the scheduler * task queue. We still also invoke the wakeup directly since that * squeezes a bit more performance out of the driver, and any lost * race conditions will get cleaned up at the next scheduler run. * * NOTE: The problem also goes away if you comment out * the two code lines in write_chan() where current->state * is set to TASK_RUNNING just before calling driver.write() and to * TASK_INTERRUPTIBLE immediately afterwards. This is why the * problem did not show up with the 2.2 kernels -- they do not * include that code. * * (5/16/2000) pberger and borchers * -- Added timeouts to sleeps, to defend against lost wake ups. * -- Handle transition to/from B0 baud rate in digi_set_termios. * * (5/13/2000) pberger and borchers * -- All commands now sent on out of band port, using * digi_write_oob_command. * -- Get modem control signals whenever they change, support TIOCMGET/ * SET/BIS/BIC ioctls. * -- digi_set_termios now supports parity, word size, stop bits, and * receive enable. * -- Cleaned up open and close, use digi_set_termios and * digi_write_oob_command to set port parameters. * -- Added digi_startup_device to start read chains on all ports. * -- Write buffer is only used when count==1, to be sure put_char can * write a char (unless the buffer is full). * * (5/10/2000) pberger and borchers * -- Added MOD_INC_USE_COUNT/MOD_DEC_USE_COUNT calls on open/close. * -- Fixed problem where the first incoming character is lost on * port opens after the first close on that port. Now we keep * the read_urb chain open until shutdown. * -- Added more port conditioning calls in digi_open and digi_close. * -- Convert port->active to a use count so that we can deal with multiple * opens and closes properly. * -- Fixed some problems with the locking code. * * (5/3/2000) pberger and borchers * -- First alpha version of the driver--many known limitations and bugs. * * * Locking and SMP * * - Each port, including the out-of-band port, has a lock used to * serialize all access to the port's private structure. * - The port lock is also used to serialize all writes and access to * the port's URB. * - The port lock is also used for the port write_wait condition * variable. Holding the port lock will prevent a wake up on the * port's write_wait; this can be used with cond_wait_... to be sure * the wake up is not lost in a race when dropping the lock and * sleeping waiting for the wakeup. * - digi_write() does not sleep, since it is sometimes called on * interrupt time. * - digi_write_bulk_callback() and digi_read_bulk_callback() are * called directly from interrupts. Hence spin_lock_irqsave() * and spin_unlock_irqrestore() are used in the rest of the code * for any locks they acquire. * - digi_write_bulk_callback() gets the port lock before waking up * processes sleeping on the port write_wait. It also schedules * wake ups so they happen from the scheduler, because the tty * system can miss wake ups from interrupts. * - All sleeps use a timeout of DIGI_RETRY_TIMEOUT before looping to * recheck the condition they are sleeping on. This is defensive, * in case a wake up is lost. * - Following Documentation/DocBook/kernel-locking.pdf no spin locks * are held when calling copy_to/from_user or printk. * * $Id: digi_acceleport.c,v 1.80.1.2 2000/11/02 05:45:08 root Exp $ */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* Defines */ /* * Version Information */ #define DRIVER_VERSION "v1.80.1.2" #define DRIVER_AUTHOR "Peter Berger , Al Borchers " #define DRIVER_DESC "Digi AccelePort USB-2/USB-4 Serial Converter driver" /* port output buffer length -- must be <= transfer buffer length - 2 */ /* so we can be sure to send the full buffer in one urb */ #define DIGI_OUT_BUF_SIZE 8 /* port input buffer length -- must be >= transfer buffer length - 3 */ /* so we can be sure to hold at least one full buffer from one urb */ #define DIGI_IN_BUF_SIZE 64 /* retry timeout while sleeping */ #define DIGI_RETRY_TIMEOUT (HZ/10) /* timeout while waiting for tty output to drain in close */ /* this delay is used twice in close, so the total delay could */ /* be twice this value */ #define DIGI_CLOSE_TIMEOUT (5*HZ) /* AccelePort USB Defines */ /* ids */ #define DIGI_VENDOR_ID 0x05c5 #define DIGI_2_ID 0x0002 /* USB-2 */ #define DIGI_4_ID 0x0004 /* USB-4 */ /* commands * "INB": can be used on the in-band endpoint * "OOB": can be used on the out-of-band endpoint */ #define DIGI_CMD_SET_BAUD_RATE 0 /* INB, OOB */ #define DIGI_CMD_SET_WORD_SIZE 1 /* INB, OOB */ #define DIGI_CMD_SET_PARITY 2 /* INB, OOB */ #define DIGI_CMD_SET_STOP_BITS 3 /* INB, OOB */ #define DIGI_CMD_SET_INPUT_FLOW_CONTROL 4 /* INB, OOB */ #define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL 5 /* INB, OOB */ #define DIGI_CMD_SET_DTR_SIGNAL 6 /* INB, OOB */ #define DIGI_CMD_SET_RTS_SIGNAL 7 /* INB, OOB */ #define DIGI_CMD_READ_INPUT_SIGNALS 8 /* OOB */ #define DIGI_CMD_IFLUSH_FIFO 9 /* OOB */ #define DIGI_CMD_RECEIVE_ENABLE 10 /* INB, OOB */ #define DIGI_CMD_BREAK_CONTROL 11 /* INB, OOB */ #define DIGI_CMD_LOCAL_LOOPBACK 12 /* INB, OOB */ #define DIGI_CMD_TRANSMIT_IDLE 13 /* INB, OOB */ #define DIGI_CMD_READ_UART_REGISTER 14 /* OOB */ #define DIGI_CMD_WRITE_UART_REGISTER 15 /* INB, OOB */ #define DIGI_CMD_AND_UART_REGISTER 16 /* INB, OOB */ #define DIGI_CMD_OR_UART_REGISTER 17 /* INB, OOB */ #define DIGI_CMD_SEND_DATA 18 /* INB */ #define DIGI_CMD_RECEIVE_DATA 19 /* INB */ #define DIGI_CMD_RECEIVE_DISABLE 20 /* INB */ #define DIGI_CMD_GET_PORT_TYPE 21 /* OOB */ /* baud rates */ #define DIGI_BAUD_50 0 #define DIGI_BAUD_75 1 #define DIGI_BAUD_110 2 #define DIGI_BAUD_150 3 #define DIGI_BAUD_200 4 #define DIGI_BAUD_300 5 #define DIGI_BAUD_600 6 #define DIGI_BAUD_1200 7 #define DIGI_BAUD_1800 8 #define DIGI_BAUD_2400 9 #define DIGI_BAUD_4800 10 #define DIGI_BAUD_7200 11 #define DIGI_BAUD_9600 12 #define DIGI_BAUD_14400 13 #define DIGI_BAUD_19200 14 #define DIGI_BAUD_28800 15 #define DIGI_BAUD_38400 16 #define DIGI_BAUD_57600 17 #define DIGI_BAUD_76800 18 #define DIGI_BAUD_115200 19 #define DIGI_BAUD_153600 20 #define DIGI_BAUD_230400 21 #define DIGI_BAUD_460800 22 /* arguments */ #define DIGI_WORD_SIZE_5 0 #define DIGI_WORD_SIZE_6 1 #define DIGI_WORD_SIZE_7 2 #define DIGI_WORD_SIZE_8 3 #define DIGI_PARITY_NONE 0 #define DIGI_PARITY_ODD 1 #define DIGI_PARITY_EVEN 2 #define DIGI_PARITY_MARK 3 #define DIGI_PARITY_SPACE 4 #define DIGI_STOP_BITS_1 0 #define DIGI_STOP_BITS_2 1 #define DIGI_INPUT_FLOW_CONTROL_XON_XOFF 1 #define DIGI_INPUT_FLOW_CONTROL_RTS 2 #define DIGI_INPUT_FLOW_CONTROL_DTR 4 #define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF 1 #define DIGI_OUTPUT_FLOW_CONTROL_CTS 2 #define DIGI_OUTPUT_FLOW_CONTROL_DSR 4 #define DIGI_DTR_INACTIVE 0 #define DIGI_DTR_ACTIVE 1 #define DIGI_DTR_INPUT_FLOW_CONTROL 2 #define DIGI_RTS_INACTIVE 0 #define DIGI_RTS_ACTIVE 1 #define DIGI_RTS_INPUT_FLOW_CONTROL 2 #define DIGI_RTS_TOGGLE 3 #define DIGI_FLUSH_TX 1 #define DIGI_FLUSH_RX 2 #define DIGI_RESUME_TX 4 /* clears xoff condition */ #define DIGI_TRANSMIT_NOT_IDLE 0 #define DIGI_TRANSMIT_IDLE 1 #define DIGI_DISABLE 0 #define DIGI_ENABLE 1 #define DIGI_DEASSERT 0 #define DIGI_ASSERT 1 /* in band status codes */ #define DIGI_OVERRUN_ERROR 4 #define DIGI_PARITY_ERROR 8 #define DIGI_FRAMING_ERROR 16 #define DIGI_BREAK_ERROR 32 /* out of band status */ #define DIGI_NO_ERROR 0 #define DIGI_BAD_FIRST_PARAMETER 1 #define DIGI_BAD_SECOND_PARAMETER 2 #define DIGI_INVALID_LINE 3 #define DIGI_INVALID_OPCODE 4 /* input signals */ #define DIGI_READ_INPUT_SIGNALS_SLOT 1 #define DIGI_READ_INPUT_SIGNALS_ERR 2 #define DIGI_READ_INPUT_SIGNALS_BUSY 4 #define DIGI_READ_INPUT_SIGNALS_PE 8 #define DIGI_READ_INPUT_SIGNALS_CTS 16 #define DIGI_READ_INPUT_SIGNALS_DSR 32 #define DIGI_READ_INPUT_SIGNALS_RI 64 #define DIGI_READ_INPUT_SIGNALS_DCD 128 /* Structures */ struct digi_serial { spinlock_t ds_serial_lock; struct usb_serial_port *ds_oob_port; /* out-of-band port */ int ds_oob_port_num; /* index of out-of-band port */ int ds_device_started; }; struct digi_port { spinlock_t dp_port_lock; int dp_port_num; int dp_out_buf_len; unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE]; int dp_write_urb_in_use; unsigned int dp_modem_signals; wait_queue_head_t dp_modem_change_wait; int dp_transmit_idle; wait_queue_head_t dp_transmit_idle_wait; int dp_throttled; int dp_throttle_restart; wait_queue_head_t dp_flush_wait; int dp_in_close; /* close in progress */ wait_queue_head_t dp_close_wait; /* wait queue for close */ struct work_struct dp_wakeup_work; struct usb_serial_port *dp_port; }; /* Local Function Declarations */ static void digi_wakeup_write( struct usb_serial_port *port ); static void digi_wakeup_write_lock(struct work_struct *work); static int digi_write_oob_command( struct usb_serial_port *port, unsigned char *buf, int count, int interruptible ); static int digi_write_inb_command( struct usb_serial_port *port, unsigned char *buf, int count, unsigned long timeout ); static int digi_set_modem_signals( struct usb_serial_port *port, unsigned int modem_signals, int interruptible ); static int digi_transmit_idle( struct usb_serial_port *port, unsigned long timeout ); static void digi_rx_throttle (struct usb_serial_port *port); static void digi_rx_unthrottle (struct usb_serial_port *port); static void digi_set_termios( struct usb_serial_port *port, struct ktermios *old_termios ); static void digi_break_ctl( struct usb_serial_port *port, int break_state ); static int digi_ioctl( struct usb_serial_port *port, struct file *file, unsigned int cmd, unsigned long arg ); static int digi_tiocmget( struct usb_serial_port *port, struct file *file ); static int digi_tiocmset( struct usb_serial_port *port, struct file *file, unsigned int set, unsigned int clear ); static int digi_write( struct usb_serial_port *port, const unsigned char *buf, int count ); static void digi_write_bulk_callback( struct urb *urb ); static int digi_write_room( struct usb_serial_port *port ); static int digi_chars_in_buffer( struct usb_serial_port *port ); static int digi_open( struct usb_serial_port *port, struct file *filp ); static void digi_close( struct usb_serial_port *port, struct file *filp ); static int digi_startup_device( struct usb_serial *serial ); static int digi_startup( struct usb_serial *serial ); static void digi_shutdown( struct usb_serial *serial ); static void digi_read_bulk_callback( struct urb *urb ); static int digi_read_inb_callback( struct urb *urb ); static int digi_read_oob_callback( struct urb *urb ); /* Statics */ static int debug; static struct usb_device_id id_table_combined [] = { { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, { } /* Terminating entry */ }; static struct usb_device_id id_table_2 [] = { { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, { } /* Terminating entry */ }; static struct usb_device_id id_table_4 [] = { { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE (usb, id_table_combined); static struct usb_driver digi_driver = { .name = "digi_acceleport", .probe = usb_serial_probe, .disconnect = usb_serial_disconnect, .id_table = id_table_combined, .no_dynamic_id = 1, }; /* device info needed for the Digi serial converter */ static struct usb_serial_driver digi_acceleport_2_device = { .driver = { .owner = THIS_MODULE, .name = "digi_2", }, .description = "Digi 2 port USB adapter", .usb_driver = &digi_driver, .id_table = id_table_2, .num_interrupt_in = 0, .num_bulk_in = 4, .num_bulk_out = 4, .num_ports = 3, .open = digi_open, .close = digi_close, .write = digi_write, .write_room = digi_write_room, .write_bulk_callback = digi_write_bulk_callback, .read_bulk_callback = digi_read_bulk_callback, .chars_in_buffer = digi_chars_in_buffer, .throttle = digi_rx_throttle, .unthrottle = digi_rx_unthrottle, .ioctl = digi_ioctl, .set_termios = digi_set_termios, .break_ctl = digi_break_ctl, .tiocmget = digi_tiocmget, .tiocmset = digi_tiocmset, .attach = digi_startup, .shutdown = digi_shutdown, }; static struct usb_serial_driver digi_acceleport_4_device = { .driver = { .owner = THIS_MODULE, .name = "digi_4", }, .description = "Digi 4 port USB adapter", .usb_driver = &digi_driver, .id_table = id_table_4, .num_interrupt_in = 0, .num_bulk_in = 5, .num_bulk_out = 5, .num_ports = 4, .open = digi_open, .close = digi_close, .write = digi_write, .write_room = digi_write_room, .write_bulk_callback = digi_write_bulk_callback, .read_bulk_callback = digi_read_bulk_callback, .chars_in_buffer = digi_chars_in_buffer, .throttle = digi_rx_throttle, .unthrottle = digi_rx_unthrottle, .ioctl = digi_ioctl, .set_termios = digi_set_termios, .break_ctl = digi_break_ctl, .tiocmget = digi_tiocmget, .tiocmset = digi_tiocmset, .attach = digi_startup, .shutdown = digi_shutdown, }; /* Functions */ /* * Cond Wait Interruptible Timeout Irqrestore * * Do spin_unlock_irqrestore and interruptible_sleep_on_timeout * so that wake ups are not lost if they occur between the unlock * and the sleep. In other words, spin_unlock_irqrestore and * interruptible_sleep_on_timeout are "atomic" with respect to * wake ups. This is used to implement condition variables. * * interruptible_sleep_on_timeout is deprecated and has been replaced * with the equivalent code. */ static inline long cond_wait_interruptible_timeout_irqrestore( wait_queue_head_t *q, long timeout, spinlock_t *lock, unsigned long flags ) { DEFINE_WAIT(wait); prepare_to_wait(q, &wait, TASK_INTERRUPTIBLE); spin_unlock_irqrestore(lock, flags); timeout = schedule_timeout(timeout); finish_wait(q, &wait); return timeout; } /* * Digi Wakeup Write * * Wake up port, line discipline, and tty processes sleeping * on writes. */ static void digi_wakeup_write_lock(struct work_struct *work) { struct digi_port *priv = container_of(work, struct digi_port, dp_wakeup_work); struct usb_serial_port *port = priv->dp_port; unsigned long flags; spin_lock_irqsave( &priv->dp_port_lock, flags ); digi_wakeup_write( port ); spin_unlock_irqrestore( &priv->dp_port_lock, flags ); } static void digi_wakeup_write( struct usb_serial_port *port ) { tty_wakeup(port->tty); } /* * Digi Write OOB Command * * Write commands on the out of band port. Commands are 4 * bytes each, multiple commands can be sent at once, and * no command will be split across USB packets. Returns 0 * if successful, -EINTR if interrupted while sleeping and * the interruptible flag is true, or a negative error * returned by usb_submit_urb. */ static int digi_write_oob_command( struct usb_serial_port *port, unsigned char *buf, int count, int interruptible ) { int ret = 0; int len; struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); unsigned long flags = 0; dbg( "digi_write_oob_command: TOP: port=%d, count=%d", oob_priv->dp_port_num, count ); spin_lock_irqsave( &oob_priv->dp_port_lock, flags ); while( count > 0 ) { while( oob_port->write_urb->status == -EINPROGRESS || oob_priv->dp_write_urb_in_use ) { cond_wait_interruptible_timeout_irqrestore( &oob_port->write_wait, DIGI_RETRY_TIMEOUT, &oob_priv->dp_port_lock, flags ); if( interruptible && signal_pending(current) ) { return( -EINTR ); } spin_lock_irqsave( &oob_priv->dp_port_lock, flags ); } /* len must be a multiple of 4, so commands are not split */ len = min(count, oob_port->bulk_out_size ); if( len > 4 ) len &= ~3; memcpy( oob_port->write_urb->transfer_buffer, buf, len ); oob_port->write_urb->transfer_buffer_length = len; oob_port->write_urb->dev = port->serial->dev; if( (ret=usb_submit_urb(oob_port->write_urb, GFP_ATOMIC)) == 0 ) { oob_priv->dp_write_urb_in_use = 1; count -= len; buf += len; } } spin_unlock_irqrestore( &oob_priv->dp_port_lock, flags ); if( ret ) { err("%s: usb_submit_urb failed, ret=%d", __FUNCTION__, ret ); } return( ret ); } /* * Digi Write In Band Command * * Write commands on the given port. Commands are 4 * bytes each, multiple commands can be sent at once, and * no command will be split across USB packets. If timeout * is non-zero, write in band command will return after * waiting unsuccessfully for the URB status to clear for * timeout ticks. Returns 0 if successful, or a negative * error returned by digi_write. */ static int digi_write_inb_command( struct usb_serial_port *port, unsigned char *buf, int count, unsigned long timeout ) { int ret = 0; int len; struct digi_port *priv = usb_get_serial_port_data(port); unsigned char *data = port->write_urb->transfer_buffer; unsigned long flags = 0; dbg( "digi_write_inb_command: TOP: port=%d, count=%d", priv->dp_port_num, count ); if( timeout ) timeout += jiffies; else timeout = ULONG_MAX; spin_lock_irqsave( &priv->dp_port_lock, flags ); while( count > 0 && ret == 0 ) { while( (port->write_urb->status == -EINPROGRESS || priv->dp_write_urb_in_use) && time_before(jiffies, timeout)) { cond_wait_interruptible_timeout_irqrestore( &port->write_wait, DIGI_RETRY_TIMEOUT, &priv->dp_port_lock, flags ); if( signal_pending(current) ) { return( -EINTR ); } spin_lock_irqsave( &priv->dp_port_lock, flags ); } /* len must be a multiple of 4 and small enough to */ /* guarantee the write will send buffered data first, */ /* so commands are in order with data and not split */ len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len ); if( len > 4 ) len &= ~3; /* write any buffered data first */ if( priv->dp_out_buf_len > 0 ) { data[0] = DIGI_CMD_SEND_DATA; data[1] = priv->dp_out_buf_len; memcpy( data+2, priv->dp_out_buf, priv->dp_out_buf_len ); memcpy( data+2+priv->dp_out_buf_len, buf, len ); port->write_urb->transfer_buffer_length = priv->dp_out_buf_len+2+len; } else { memcpy( data, buf, len ); port->write_urb->transfer_buffer_length = len; } port->write_urb->dev = port->serial->dev; if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) { priv->dp_write_urb_in_use = 1; priv->dp_out_buf_len = 0; count -= len; buf += len; } } spin_unlock_irqrestore( &priv->dp_port_lock, flags ); if( ret ) { err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num ); } return( ret ); } /* * Digi Set Modem Signals * * Sets or clears DTR and RTS on the port, according to the * modem_signals argument. Use TIOCM_DTR and TIOCM_RTS flags * for the modem_signals argument. Returns 0 if successful, * -EINTR if interrupted while sleeping, or a non-zero error * returned by usb_submit_urb. */ static int digi_set_modem_signals( struct usb_serial_port *port, unsigned int modem_signals, int interruptible ) { int ret; struct digi_port *port_priv = usb_get_serial_port_data(port); struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); unsigned char *data = oob_port->write_urb->transfer_buffer; unsigned long flags = 0; dbg( "digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x", port_priv->dp_port_num, modem_signals ); spin_lock_irqsave( &oob_priv->dp_port_lock, flags ); spin_lock( &port_priv->dp_port_lock ); while( oob_port->write_urb->status == -EINPROGRESS || oob_priv->dp_write_urb_in_use ) { spin_unlock( &port_priv->dp_port_lock ); cond_wait_interruptible_timeout_irqrestore( &oob_port->write_wait, DIGI_RETRY_TIMEOUT, &oob_priv->dp_port_lock, flags ); if( interruptible && signal_pending(current) ) { return( -EINTR ); } spin_lock_irqsave( &oob_priv->dp_port_lock, flags ); spin_lock( &port_priv->dp_port_lock ); } data[0] = DIGI_CMD_SET_DTR_SIGNAL; data[1] = port_priv->dp_port_num; data[2] = (modem_signals&TIOCM_DTR) ? DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE; data[3] = 0; data[4] = DIGI_CMD_SET_RTS_SIGNAL; data[5] = port_priv->dp_port_num; data[6] = (modem_signals&TIOCM_RTS) ? DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE; data[7] = 0; oob_port->write_urb->transfer_buffer_length = 8; oob_port->write_urb->dev = port->serial->dev; if( (ret=usb_submit_urb(oob_port->write_urb, GFP_ATOMIC)) == 0 ) { oob_priv->dp_write_urb_in_use = 1; port_priv->dp_modem_signals = (port_priv->dp_modem_signals&~(TIOCM_DTR|TIOCM_RTS)) | (modem_signals&(TIOCM_DTR|TIOCM_RTS)); } spin_unlock( &port_priv->dp_port_lock ); spin_unlock_irqrestore( &oob_priv->dp_port_lock, flags ); if( ret ) { err("%s: usb_submit_urb failed, ret=%d", __FUNCTION__, ret ); } return( ret ); } /* * Digi Transmit Idle * * Digi transmit idle waits, up to timeout ticks, for the transmitter * to go idle. It returns 0 if successful or a negative error. * * There are race conditions here if more than one process is calling * digi_transmit_idle on the same port at the same time. However, this * is only called from close, and only one process can be in close on a * port at a time, so its ok. */ static int digi_transmit_idle( struct usb_serial_port *port, unsigned long timeout ) { int ret; unsigned char buf[2]; struct digi_port *priv = usb_get_serial_port_data(port); unsigned long flags = 0; spin_lock_irqsave( &priv->dp_port_lock, flags ); priv->dp_transmit_idle = 0; spin_unlock_irqrestore( &priv->dp_port_lock, flags ); buf[0] = DIGI_CMD_TRANSMIT_IDLE; buf[1] = 0; timeout += jiffies; if( (ret=digi_write_inb_command( port, buf, 2, timeout-jiffies )) != 0 ) return( ret ); spin_lock_irqsave( &priv->dp_port_lock, flags ); while( time_before(jiffies, timeout) && !priv->dp_transmit_idle ) { cond_wait_interruptible_timeout_irqrestore( &priv->dp_transmit_idle_wait, DIGI_RETRY_TIMEOUT, &priv->dp_port_lock, flags ); if( signal_pending(current) ) { return( -EINTR ); } spin_lock_irqsave( &priv->dp_port_lock, flags ); } priv->dp_transmit_idle = 0; spin_unlock_irqrestore( &priv->dp_port_lock, flags ); return( 0 ); } static void digi_rx_throttle( struct usb_serial_port *port ) { unsigned long flags; struct digi_port *priv = usb_get_serial_port_data(port); dbg( "digi_rx_throttle: TOP: port=%d", priv->dp_port_num ); /* stop receiving characters by not resubmitting the read urb */ spin_lock_irqsave( &priv->dp_port_lock, flags ); priv->dp_throttled = 1; priv->dp_throttle_restart = 0; spin_unlock_irqrestore( &priv->dp_port_lock, flags ); } static void digi_rx_unthrottle( struct usb_serial_port *port ) { int ret = 0; unsigned long flags; struct digi_port *priv = usb_get_serial_port_data(port); dbg( "digi_rx_unthrottle: TOP: port=%d", priv->dp_port_num ); spin_lock_irqsave( &priv->dp_port_lock, flags ); /* turn throttle off */ priv->dp_throttled = 0; priv->dp_throttle_restart = 0; /* restart read chain */ if( priv->dp_throttle_restart ) { port->read_urb->dev = port->serial->dev; ret = usb_submit_urb( port->read_urb, GFP_ATOMIC ); } spin_unlock_irqrestore( &priv->dp_port_lock, flags ); if( ret ) { err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num ); } } static void digi_set_termios( struct usb_serial_port *port, struct ktermios *old_termios ) { struct digi_port *priv = usb_get_serial_port_data(port); unsigned int iflag = port->tty->termios->c_iflag; unsigned int cflag = port->tty->termios->c_cflag; unsigned int old_iflag = old_termios->c_iflag; unsigned int old_cflag = old_termios->c_cflag; unsigned char buf[32]; unsigned int modem_signals; int arg,ret; int i = 0; dbg( "digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x, old_cflag=0x%x", priv->dp_port_num, iflag, old_iflag, cflag, old_cflag ); /* set baud rate */ if( (cflag&CBAUD) != (old_cflag&CBAUD) ) { arg = -1; /* reassert DTR and (maybe) RTS on transition from B0 */ if( (old_cflag&CBAUD) == B0 ) { /* don't set RTS if using hardware flow control */ /* and throttling input */ modem_signals = TIOCM_DTR; if( !(port->tty->termios->c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &port->tty->flags) ) { modem_signals |= TIOCM_RTS; } digi_set_modem_signals( port, modem_signals, 1 ); } switch( (cflag&CBAUD) ) { /* drop DTR and RTS on transition to B0 */ case B0: digi_set_modem_signals( port, 0, 1 ); break; case B50: arg = DIGI_BAUD_50; break; case B75: arg = DIGI_BAUD_75; break; case B110: arg = DIGI_BAUD_110; break; case B150: arg = DIGI_BAUD_150; break; case B200: arg = DIGI_BAUD_200; break; case B300: arg = DIGI_BAUD_300; break; case B600: arg = DIGI_BAUD_600; break; case B1200: arg = DIGI_BAUD_1200; break; case B1800: arg = DIGI_BAUD_1800; break; case B2400: arg = DIGI_BAUD_2400; break; case B4800: arg = DIGI_BAUD_4800; break; case B9600: arg = DIGI_BAUD_9600; break; case B19200: arg = DIGI_BAUD_19200; break; case B38400: arg = DIGI_BAUD_38400; break; case B57600: arg = DIGI_BAUD_57600; break; case B115200: arg = DIGI_BAUD_115200; break; case B230400: arg = DIGI_BAUD_230400; break; case B460800: arg = DIGI_BAUD_460800; break; default: dbg( "digi_set_termios: can't handle baud rate 0x%x", (cflag&CBAUD) ); break; } if( arg != -1 ) { buf[i++] = DIGI_CMD_SET_BAUD_RATE; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } } /* set parity */ if( (cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD)) ) { if( (cflag&PARENB) ) { if( (cflag&PARODD) ) arg = DIGI_PARITY_ODD; else arg = DIGI_PARITY_EVEN; } else { arg = DIGI_PARITY_NONE; } buf[i++] = DIGI_CMD_SET_PARITY; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } /* set word size */ if( (cflag&CSIZE) != (old_cflag&CSIZE) ) { arg = -1; switch( (cflag&CSIZE) ) { case CS5: arg = DIGI_WORD_SIZE_5; break; case CS6: arg = DIGI_WORD_SIZE_6; break; case CS7: arg = DIGI_WORD_SIZE_7; break; case CS8: arg = DIGI_WORD_SIZE_8; break; default: dbg( "digi_set_termios: can't handle word size %d", (cflag&CSIZE) ); break; } if( arg != -1 ) { buf[i++] = DIGI_CMD_SET_WORD_SIZE; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } } /* set stop bits */ if( (cflag&CSTOPB) != (old_cflag&CSTOPB) ) { if( (cflag&CSTOPB) ) arg = DIGI_STOP_BITS_2; else arg = DIGI_STOP_BITS_1; buf[i++] = DIGI_CMD_SET_STOP_BITS; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } /* set input flow control */ if( (iflag&IXOFF) != (old_iflag&IXOFF) || (cflag&CRTSCTS) != (old_cflag&CRTSCTS) ) { arg = 0; if( (iflag&IXOFF) ) arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF; else arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF; if( (cflag&CRTSCTS) ) { arg |= DIGI_INPUT_FLOW_CONTROL_RTS; /* On USB-4 it is necessary to assert RTS prior */ /* to selecting RTS input flow control. */ buf[i++] = DIGI_CMD_SET_RTS_SIGNAL; buf[i++] = priv->dp_port_num; buf[i++] = DIGI_RTS_ACTIVE; buf[i++] = 0; } else { arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS; } buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } /* set output flow control */ if( (iflag&IXON) != (old_iflag&IXON) || (cflag&CRTSCTS) != (old_cflag&CRTSCTS) ) { arg = 0; if( (iflag&IXON) ) arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; else arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; if( (cflag&CRTSCTS) ) { arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS; } else { arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS; port->tty->hw_stopped = 0; } buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } /* set receive enable/disable */ if( (cflag&CREAD) != (old_cflag&CREAD) ) { if( (cflag&CREAD) ) arg = DIGI_ENABLE; else arg = DIGI_DISABLE; buf[i++] = DIGI_CMD_RECEIVE_ENABLE; buf[i++] = priv->dp_port_num; buf[i++] = arg; buf[i++] = 0; } if( (ret=digi_write_oob_command( port, buf, i, 1 )) != 0 ) dbg( "digi_set_termios: write oob failed, ret=%d", ret ); } static void digi_break_ctl( struct usb_serial_port *port, int break_state ) { unsigned char buf[4]; buf[0] = DIGI_CMD_BREAK_CONTROL; buf[1] = 2; /* length */ buf[2] = break_state ? 1 : 0; buf[3] = 0; /* pad */ digi_write_inb_command( port, buf, 4, 0 ); } static int digi_tiocmget( struct usb_serial_port *port, struct file *file ) { struct digi_port *priv = usb_get_serial_port_data(port); unsigned int val; unsigned long flags; dbg("%s: TOP: port=%d", __FUNCTION__, priv->dp_port_num); spin_lock_irqsave( &priv->dp_port_lock, flags ); val = priv->dp_modem_signals; spin_unlock_irqrestore( &priv->dp_port_lock, flags ); return val; } static int digi_tiocmset( struct usb_serial_port *port, struct file *file, unsigned int set, unsigned int clear ) { struct digi_port *priv = usb_get_serial_port_data(port); unsigned int val; unsigned long flags; dbg("%s: TOP: port=%d", __FUNCTION__, priv->dp_port_num); spin_lock_irqsave( &priv->dp_port_lock, flags ); val = (priv->dp_modem_signals & ~clear) | set; spin_unlock_irqrestore( &priv->dp_port_lock, flags ); return digi_set_modem_signals( port, val, 1 ); } static int digi_ioctl( struct usb_serial_port *port, struct file *file, unsigned int cmd, unsigned long arg ) { struct digi_port *priv = usb_get_serial_port_data(port); dbg( "digi_ioctl: TOP: port=%d, cmd=0x%x", priv->dp_port_num, cmd ); switch (cmd) { case TIOCMIWAIT: /* wait for any of the 4 modem inputs (DCD,RI,DSR,CTS)*/ /* TODO */ return( 0 ); case TIOCGICOUNT: /* return count of modemline transitions */ /* TODO */ return 0; } return( -ENOIOCTLCMD ); } static int digi_write( struct usb_serial_port *port, const unsigned char *buf, int count ) { int ret,data_len,new_len; struct digi_port *priv = usb_get_serial_port_data(port); unsigned char *data = port->write_urb->transfer_buffer; unsigned long flags = 0; dbg( "digi_write: TOP: port=%d, count=%d, in_interrupt=%ld", priv->dp_port_num, count, in_interrupt() ); /* copy user data (which can sleep) before getting spin lock */ count = min( count, port->bulk_out_size-2 ); count = min( 64, count); /* be sure only one write proceeds at a time */ /* there are races on the port private buffer */ /* and races to check write_urb->status */ spin_lock_irqsave( &priv->dp_port_lock, flags ); /* wait for urb status clear to submit another urb */ if( port->write_urb->status == -EINPROGRESS || priv->dp_write_urb_in_use ) { /* buffer data if count is 1 (probably put_char) if possible */ if( count == 1 && priv->dp_out_buf_len < DIGI_OUT_BUF_SIZE ) { priv->dp_out_buf[priv->dp_out_buf_len++] = *buf; new_len = 1; } else { new_len = 0; } spin_unlock_irqrestore( &priv->dp_port_lock, flags ); return( new_len ); } /* allow space for any buffered data and for new data, up to */ /* transfer buffer size - 2 (for command and length bytes) */ new_len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); data_len = new_len + priv->dp_out_buf_len; if( data_len == 0 ) { spin_unlock_irqrestore( &priv->dp_port_lock, flags ); return( 0 ); } port->write_urb->transfer_buffer_length = data_len+2; port->write_urb->dev = port->serial->dev; *data++ = DIGI_CMD_SEND_DATA; *data++ = data_len; /* copy in buffered data first */ memcpy( data, priv->dp_out_buf, priv->dp_out_buf_len ); data += priv->dp_out_buf_len; /* copy in new data */ memcpy( data, buf, new_len ); if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) { priv->dp_write_urb_in_use = 1; ret = new_len; priv->dp_out_buf_len = 0; } /* return length of new data written, or error */ spin_unlock_irqrestore( &priv->dp_port_lock, flags ); if( ret < 0 ) { err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num ); } dbg( "digi_write: returning %d", ret ); return( ret ); } static void digi_write_bulk_callback( struct urb *urb ) { struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct usb_serial *serial; struct digi_port *priv; struct digi_serial *serial_priv; int ret = 0; dbg( "digi_write_bulk_callback: TOP, urb->status=%d", urb->status ); /* port and serial sanity check */ if( port == NULL || (priv=usb_get_serial_port_data(port)) == NULL ) { err("%s: port or port->private is NULL, status=%d", __FUNCTION__, urb->status ); return; } serial = port->serial; if( serial == NULL || (serial_priv=usb_get_serial_data(serial)) == NULL ) { err("%s: serial or serial->private is NULL, status=%d", __FUNCTION__, urb->status ); return; } /* handle oob callback */ if( priv->dp_port_num == serial_priv->ds_oob_port_num ) { dbg( "digi_write_bulk_callback: oob callback" ); spin_lock( &priv->dp_port_lock ); priv->dp_write_urb_in_use = 0; wake_up_interruptible( &port->write_wait ); spin_unlock( &priv->dp_port_lock ); return; } /* try to send any buffered data on this port, if it is open */ spin_lock( &priv->dp_port_lock ); priv->dp_write_urb_in_use = 0; if( port->open_count && port->write_urb->status != -EINPROGRESS && priv->dp_out_buf_len > 0 ) { *((unsigned char *)(port->write_urb->transfer_buffer)) = (unsigned char)DIGI_CMD_SEND_DATA; *((unsigned char *)(port->write_urb->transfer_buffer)+1) = (unsigned char)priv->dp_out_buf_len; port->write_urb->transfer_buffer_length = priv->dp_out_buf_len+2; port->write_urb->dev = serial->dev; memcpy( port->write_urb->transfer_buffer+2, priv->dp_out_buf, priv->dp_out_buf_len ); if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) { priv->dp_write_urb_in_use = 1; priv->dp_out_buf_len = 0; } } /* wake up processes sleeping on writes immediately */ digi_wakeup_write( port ); /* also queue up a wakeup at scheduler time, in case we */ /* lost the race in write_chan(). */ schedule_work(&priv->dp_wakeup_work); spin_unlock( &priv->dp_port_lock ); if( ret ) { err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num ); } } static int digi_write_room( struct usb_serial_port *port ) { int room; struct digi_port *priv = usb_get_serial_port_data(port); unsigned long flags = 0; spin_lock_irqsave( &priv->dp_port_lock, flags ); if( port->write_urb->status == -EINPROGRESS || priv->dp_write_urb_in_use ) room = 0; else room = port->bulk_out_size - 2 - priv->dp_out_buf_len; spin_unlock_irqrestore( &priv->dp_port_lock, flags ); dbg( "digi_write_room: port=%d, room=%d", priv->dp_port_num, room ); return( room ); } static int digi_chars_in_buffer( struct usb_serial_port *port ) { struct digi_port *priv = usb_get_serial_port_data(port); if( port->write_urb->status == -EINPROGRESS || priv->dp_write_urb_in_use ) { dbg( "digi_chars_in_buffer: port=%d, chars=%d", priv->dp_port_num, port->bulk_out_size - 2 ); /* return( port->bulk_out_size - 2 ); */ return( 256 ); } else { dbg( "digi_chars_in_buffer: port=%d, chars=%d", priv->dp_port_num, priv->dp_out_buf_len ); return( priv->dp_out_buf_len ); } } static int digi_open( struct usb_serial_port *port, struct file *filp ) { int ret; unsigned char buf[32]; struct digi_port *priv = usb_get_serial_port_data(port); struct ktermios not_termios; unsigned long flags = 0; dbg( "digi_open: TOP: port=%d, open_count=%d", priv->dp_port_num, port->open_count ); /* be sure the device is started up */ if( digi_startup_device( port->serial ) != 0 ) return( -ENXIO ); spin_lock_irqsave( &priv->dp_port_lock, flags ); /* don't wait on a close in progress for non-blocking opens */ if( priv->dp_in_close && (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) { spin_unlock_irqrestore( &priv->dp_port_lock, flags ); return( -EAGAIN ); } /* wait for a close in progress to finish */ while( priv->dp_in_close ) { cond_wait_interruptible_timeout_irqrestore( &priv->dp_close_wait, DIGI_RETRY_TIMEOUT, &priv->dp_port_lock, flags ); if( signal_pending(current) ) { return( -EINTR ); } spin_lock_irqsave( &priv->dp_port_lock, flags ); } spin_unlock_irqrestore( &priv->dp_port_lock, flags ); /* read modem signals automatically whenever they change */ buf[0] = DIGI_CMD_READ_INPUT_SIGNALS; buf[1] = priv->dp_port_num; buf[2] = DIGI_ENABLE; buf[3] = 0; /* flush fifos */ buf[4] = DIGI_CMD_IFLUSH_FIFO; buf[5] = priv->dp_port_num; buf[6] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; buf[7] = 0; if( (ret=digi_write_oob_command( port, buf, 8, 1 )) != 0 ) dbg( "digi_open: write oob failed, ret=%d", ret ); /* set termios settings */ not_termios.c_cflag = ~port->tty->termios->c_cflag; not_termios.c_iflag = ~port->tty->termios->c_iflag; digi_set_termios( port, ¬_termios ); /* set DTR and RTS */ digi_set_modem_signals( port, TIOCM_DTR|TIOCM_RTS, 1 ); return( 0 ); } static void digi_close( struct usb_serial_port *port, struct file *filp ) { DEFINE_WAIT(wait); int ret; unsigned char buf[32]; struct tty_struct *tty = port->tty; struct digi_port *priv = usb_get_serial_port_data(port); unsigned long flags = 0; dbg( "digi_close: TOP: port=%d, open_count=%d", priv->dp_port_num, port->open_count ); /* if disconnected, just clear flags */ if (!usb_get_intfdata(port->serial->interface)) goto exit; /* do cleanup only after final close on this port */ spin_lock_irqsave( &priv->dp_port_lock, flags ); priv->dp_in_close = 1; spin_unlock_irqrestore( &priv->dp_port_lock, flags ); /* tell line discipline to process only XON/XOFF */ tty->closing = 1; /* wait for output to drain */ if( (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) { tty_wait_until_sent( tty, DIGI_CLOSE_TIMEOUT ); } /* flush driver and line discipline buffers */ if( tty->driver->flush_buffer ) tty->driver->flush_buffer( tty ); tty_ldisc_flush(tty); if (port->serial->dev) { /* wait for transmit idle */ if( (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) { digi_transmit_idle( port, DIGI_CLOSE_TIMEOUT ); } /* drop DTR and RTS */ digi_set_modem_signals( port, 0, 0 ); /* disable input flow control */ buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; buf[1] = priv->dp_port_num; buf[2] = DIGI_DISABLE; buf[3] = 0; /* disable output flow control */ buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; buf[5] = priv->dp_port_num; buf[6] = DIGI_DISABLE; buf[7] = 0; /* disable reading modem signals automatically */ buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; buf[9] = priv->dp_port_num; buf[10] = DIGI_DISABLE; buf[11] = 0; /* disable receive */ buf[12] = DIGI_CMD_RECEIVE_ENABLE; buf[13] = priv->dp_port_num; buf[14] = DIGI_DISABLE; buf[15] = 0; /* flush fifos */ buf[16] = DIGI_CMD_IFLUSH_FIFO; buf[17] = priv->dp_port_num; buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; buf[19] = 0; if( (ret=digi_write_oob_command( port, buf, 20, 0 )) != 0 ) dbg( "digi_close: write oob failed, ret=%d", ret ); /* wait for final commands on oob port to complete */ prepare_to_wait(&priv->dp_flush_wait, &wait, TASK_INTERRUPTIBLE); schedule_timeout(DIGI_CLOSE_TIMEOUT); finish_wait(&priv->dp_flush_wait, &wait); /* shutdown any outstanding bulk writes */ usb_kill_urb(port->write_urb); } tty->closing = 0; exit: spin_lock_irqsave( &priv->dp_port_lock, flags ); priv->dp_write_urb_in_use = 0; priv->dp_in_close = 0; wake_up_interruptible( &priv->dp_close_wait ); spin_unlock_irqrestore( &priv->dp_port_lock, flags ); dbg( "digi_close: done" ); } /* * Digi Startup Device * * Starts reads on all ports. Must be called AFTER startup, with * urbs initialized. Returns 0 if successful, non-zero error otherwise. */ static int digi_startup_device( struct usb_serial *serial ) { int i,ret = 0; struct digi_serial *serial_priv = usb_get_serial_data(serial); struct usb_serial_port *port; /* be sure this happens exactly once */ spin_lock( &serial_priv->ds_serial_lock ); if( serial_priv->ds_device_started ) { spin_unlock( &serial_priv->ds_serial_lock ); return( 0 ); } serial_priv->ds_device_started = 1; spin_unlock( &serial_priv->ds_serial_lock ); /* start reading from each bulk in endpoint for the device */ /* set USB_DISABLE_SPD flag for write bulk urbs */ for( i=0; itype->num_ports+1; i++ ) { port = serial->port[i]; port->write_urb->dev = port->serial->dev; if( (ret=usb_submit_urb(port->read_urb, GFP_KERNEL)) != 0 ) { err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, ret, i ); break; } } return( ret ); } static int digi_startup( struct usb_serial *serial ) { int i; struct digi_port *priv; struct digi_serial *serial_priv; dbg( "digi_startup: TOP" ); /* allocate the private data structures for all ports */ /* number of regular ports + 1 for the out-of-band port */ for( i=0; itype->num_ports+1; i++ ) { /* allocate port private structure */ priv = kmalloc( sizeof(struct digi_port), GFP_KERNEL ); if( priv == (struct digi_port *)0 ) { while( --i >= 0 ) kfree( usb_get_serial_port_data(serial->port[i]) ); return( 1 ); /* error */ } /* initialize port private structure */ spin_lock_init( &priv->dp_port_lock ); priv->dp_port_num = i; priv->dp_out_buf_len = 0; priv->dp_write_urb_in_use = 0; priv->dp_modem_signals = 0; init_waitqueue_head( &priv->dp_modem_change_wait ); priv->dp_transmit_idle = 0; init_waitqueue_head( &priv->dp_transmit_idle_wait ); priv->dp_throttled = 0; priv->dp_throttle_restart = 0; init_waitqueue_head( &priv->dp_flush_wait ); priv->dp_in_close = 0; init_waitqueue_head( &priv->dp_close_wait ); INIT_WORK(&priv->dp_wakeup_work, digi_wakeup_write_lock); priv->dp_port = serial->port[i]; /* initialize write wait queue for this port */ init_waitqueue_head( &serial->port[i]->write_wait ); usb_set_serial_port_data(serial->port[i], priv); } /* allocate serial private structure */ serial_priv = kmalloc( sizeof(struct digi_serial), GFP_KERNEL ); if( serial_priv == (struct digi_serial *)0 ) { for( i=0; itype->num_ports+1; i++ ) kfree( usb_get_serial_port_data(serial->port[i]) ); return( 1 ); /* error */ } /* initialize serial private structure */ spin_lock_init( &serial_priv->ds_serial_lock ); serial_priv->ds_oob_port_num = serial->type->num_ports; serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num]; serial_priv->ds_device_started = 0; usb_set_serial_data(serial, serial_priv); return( 0 ); } static void digi_shutdown( struct usb_serial *serial ) { int i; dbg( "digi_shutdown: TOP, in_interrupt()=%ld", in_interrupt() ); /* stop reads and writes on all ports */ for( i=0; itype->num_ports+1; i++ ) { usb_kill_urb(serial->port[i]->read_urb); usb_kill_urb(serial->port[i]->write_urb); } /* free the private data structures for all ports */ /* number of regular ports + 1 for the out-of-band port */ for( i=0; itype->num_ports+1; i++ ) kfree( usb_get_serial_port_data(serial->port[i]) ); kfree( usb_get_serial_data(serial) ); } static void digi_read_bulk_callback( struct urb *urb ) { struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct digi_port *priv; struct digi_serial *serial_priv; int ret; dbg( "digi_read_bulk_callback: TOP" ); /* port sanity check, do not resubmit if port is not valid */ if( port == NULL || (priv=usb_get_serial_port_data(port)) == NULL ) { err("%s: port or port->private is NULL, status=%d", __FUNCTION__, urb->status ); return; } if( port->serial == NULL || (serial_priv=usb_get_serial_data(port->serial)) == NULL ) { err("%s: serial is bad or serial->private is NULL, status=%d", __FUNCTION__, urb->status ); return; } /* do not resubmit urb if it has any status error */ if( urb->status ) { err("%s: nonzero read bulk status: status=%d, port=%d", __FUNCTION__, urb->status, priv->dp_port_num ); return; } /* handle oob or inb callback, do not resubmit if error */ if( priv->dp_port_num == serial_priv->ds_oob_port_num ) { if( digi_read_oob_callback( urb ) != 0 ) return; } else { if( digi_read_inb_callback( urb ) != 0 ) return; } /* continue read */ urb->dev = port->serial->dev; if( (ret=usb_submit_urb(urb, GFP_ATOMIC)) != 0 ) { err("%s: failed resubmitting urb, ret=%d, port=%d", __FUNCTION__, ret, priv->dp_port_num ); } } /* * Digi Read INB Callback * * Digi Read INB Callback handles reads on the in band ports, sending * the data on to the tty subsystem. When called we know port and * port->private are not NULL and port->serial has been validated. * It returns 0 if successful, 1 if successful but the port is * throttled, and -1 if the sanity checks failed. */ static int digi_read_inb_callback( struct urb *urb ) { struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct tty_struct *tty = port->tty; struct digi_port *priv = usb_get_serial_port_data(port); int opcode = ((unsigned char *)urb->transfer_buffer)[0]; int len = ((unsigned char *)urb->transfer_buffer)[1]; int status = ((unsigned char *)urb->transfer_buffer)[2]; unsigned char *data = ((unsigned char *)urb->transfer_buffer)+3; int flag,throttled; int i; /* do not process callbacks on closed ports */ /* but do continue the read chain */ if( port->open_count == 0 ) return( 0 ); /* short/multiple packet check */ if( urb->actual_length != len + 2 ) { err("%s: INCOMPLETE OR MULTIPLE PACKET, urb->status=%d, port=%d, opcode=%d, len=%d, actual_length=%d, status=%d", __FUNCTION__, urb->status, priv->dp_port_num, opcode, len, urb->actual_length, status ); return( -1 ); } spin_lock( &priv->dp_port_lock ); /* check for throttle; if set, do not resubmit read urb */ /* indicate the read chain needs to be restarted on unthrottle */ throttled = priv->dp_throttled; if( throttled ) priv->dp_throttle_restart = 1; /* receive data */ if( opcode == DIGI_CMD_RECEIVE_DATA ) { /* get flag from status */ flag = 0; /* overrun is special, not associated with a char */ if( status & DIGI_OVERRUN_ERROR ) { tty_insert_flip_char( tty, 0, TTY_OVERRUN ); } /* break takes precedence over parity, */ /* which takes precedence over framing errors */ if( status & DIGI_BREAK_ERROR ) { flag = TTY_BREAK; } else if( status & DIGI_PARITY_ERROR ) { flag = TTY_PARITY; } else if( status & DIGI_FRAMING_ERROR ) { flag = TTY_FRAME; } /* data length is len-1 (one byte of len is status) */ --len; len = tty_buffer_request_room(tty, len); if( len > 0 ) { /* Hot path */ if(flag == TTY_NORMAL) tty_insert_flip_string(tty, data, len); else { for(i = 0; i < len; i++) tty_insert_flip_char(tty, data[i], flag); } tty_flip_buffer_push( tty ); } } spin_unlock( &priv->dp_port_lock ); if( opcode == DIGI_CMD_RECEIVE_DISABLE ) { dbg("%s: got RECEIVE_DISABLE", __FUNCTION__ ); } else if( opcode != DIGI_CMD_RECEIVE_DATA ) { dbg("%s: unknown opcode: %d", __FUNCTION__, opcode ); } return( throttled ? 1 : 0 ); } /* * Digi Read OOB Callback * * Digi Read OOB Callback handles reads on the out of band port. * When called we know port and port->private are not NULL and * the port->serial is valid. It returns 0 if successful, and * -1 if the sanity checks failed. */ static int digi_read_oob_callback( struct urb *urb ) { struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct usb_serial *serial = port->serial; struct digi_port *priv = usb_get_serial_port_data(port); int opcode, line, status, val; int i; dbg( "digi_read_oob_callback: port=%d, len=%d", priv->dp_port_num, urb->actual_length ); /* handle each oob command */ for( i=0; iactual_length-3; ) { opcode = ((unsigned char *)urb->transfer_buffer)[i++]; line = ((unsigned char *)urb->transfer_buffer)[i++]; status = ((unsigned char *)urb->transfer_buffer)[i++]; val = ((unsigned char *)urb->transfer_buffer)[i++]; dbg( "digi_read_oob_callback: opcode=%d, line=%d, status=%d, val=%d", opcode, line, status, val ); if( status != 0 || line >= serial->type->num_ports ) continue; port = serial->port[line]; if ((priv=usb_get_serial_port_data(port)) == NULL ) return -1; if( opcode == DIGI_CMD_READ_INPUT_SIGNALS ) { spin_lock( &priv->dp_port_lock ); /* convert from digi flags to termiox flags */ if( val & DIGI_READ_INPUT_SIGNALS_CTS ) { priv->dp_modem_signals |= TIOCM_CTS; /* port must be open to use tty struct */ if( port->open_count && port->tty->termios->c_cflag & CRTSCTS ) { port->tty->hw_stopped = 0; digi_wakeup_write( port ); } } else { priv->dp_modem_signals &= ~TIOCM_CTS; /* port must be open to use tty struct */ if( port->open_count && port->tty->termios->c_cflag & CRTSCTS ) { port->tty->hw_stopped = 1; } } if( val & DIGI_READ_INPUT_SIGNALS_DSR ) priv->dp_modem_signals |= TIOCM_DSR; else priv->dp_modem_signals &= ~TIOCM_DSR; if( val & DIGI_READ_INPUT_SIGNALS_RI ) priv->dp_modem_signals |= TIOCM_RI; else priv->dp_modem_signals &= ~TIOCM_RI; if( val & DIGI_READ_INPUT_SIGNALS_DCD ) priv->dp_modem_signals |= TIOCM_CD; else priv->dp_modem_signals &= ~TIOCM_CD; wake_up_interruptible( &priv->dp_modem_change_wait ); spin_unlock( &priv->dp_port_lock ); } else if( opcode == DIGI_CMD_TRANSMIT_IDLE ) { spin_lock( &priv->dp_port_lock ); priv->dp_transmit_idle = 1; wake_up_interruptible( &priv->dp_transmit_idle_wait ); spin_unlock( &priv->dp_port_lock ); } else if( opcode == DIGI_CMD_IFLUSH_FIFO ) { wake_up_interruptible( &priv->dp_flush_wait ); } } return( 0 ); } static int __init digi_init (void) { int retval; retval = usb_serial_register(&digi_acceleport_2_device); if (retval) goto failed_acceleport_2_device; retval = usb_serial_register(&digi_acceleport_4_device); if (retval) goto failed_acceleport_4_device; retval = usb_register(&digi_driver); if (retval) goto failed_usb_register; info(DRIVER_VERSION ":" DRIVER_DESC); return 0; failed_usb_register: usb_serial_deregister(&digi_acceleport_4_device); failed_acceleport_4_device: usb_serial_deregister(&digi_acceleport_2_device); failed_acceleport_2_device: return retval; } static void __exit digi_exit (void) { usb_deregister (&digi_driver); usb_serial_deregister (&digi_acceleport_2_device); usb_serial_deregister (&digi_acceleport_4_device); } module_init(digi_init); module_exit(digi_exit); MODULE_AUTHOR( DRIVER_AUTHOR ); MODULE_DESCRIPTION( DRIVER_DESC ); MODULE_LICENSE("GPL"); module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug enabled or not");