Merge rsync://rsync.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6

8 files changed, 214 insertions, 11 deletions

diff --git a/Documentation/hwmon/f71805f b/Documentation/hwmon/f71805f
index 2ca69df669c..bfd0f154959 100644
--- a/Documentation/hwmon/f71805f
+++ b/Documentation/hwmon/f71805f
@@ -6,6 +6,10 @@ Supported chips:
     Prefix: 'f71805f'
     Addresses scanned: none, address read from Super I/O config space
     Datasheet: Provided by Fintek on request
+  * Fintek F71872F/FG
+    Prefix: 'f71872f'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: Provided by Fintek on request
 
 Author: Jean Delvare <khali@linux-fr.org>
 
@@ -13,8 +17,8 @@ Thanks to Denis Kieft from Barracuda Networks for the donation of a
 test system (custom Jetway K8M8MS motherboard, with CPU and RAM) and
 for providing initial documentation.
 
-Thanks to Kris Chen from Fintek for answering technical questions and
-providing additional documentation.
+Thanks to Kris Chen and Aaron Huang from Fintek for answering technical
+questions and providing additional documentation.
 
 Thanks to Chris Lin from Jetway for providing wiring schematics and
 answering technical questions.
@@ -28,8 +32,11 @@ capabilities. It can monitor up to 9 voltages (counting its own power
 source), 3 fans and 3 temperature sensors.
 
 This chip also has fan controlling features, using either DC or PWM, in
-three different modes (one manual, two automatic). The driver doesn't
-support these features yet.
+three different modes (one manual, two automatic).
+
+The Fintek F71872F/FG Super I/O chip is almost the same, with two
+additional internal voltages monitored (VSB and battery). It also features
+6 VID inputs. The VID inputs are not yet supported by this driver.
 
 The driver assumes that no more than one chip is present, which seems
 reasonable.
@@ -42,7 +49,8 @@ Voltages are sampled by an 8-bit ADC with a LSB of 8 mV. The supported
 range is thus from 0 to 2.040 V. Voltage values outside of this range
 need external resistors. An exception is in0, which is used to monitor
 the chip's own power source (+3.3V), and is divided internally by a
-factor 2.
+factor 2. For the F71872F/FG, in9 (VSB) and in10 (battery) are also
+divided internally by a factor 2.
 
 The two LSB of the voltage limit registers are not used (always 0), so
 you can only set the limits in steps of 32 mV (before scaling).
@@ -61,9 +69,12 @@ in5     VIN5    +12V        200K     20K       11.00    1.05 V
 in6     VIN6    VCC1.5V      10K       -        1.00    1.50 V
 in7     VIN7    VCORE        10K       -        1.00   ~1.40 V (1)
 in8     VIN8    VSB5V       200K     47K        1.00    0.95 V
+in10    VSB     VSB3.3V     int.    int.        2.00    1.65 V (3)
+in9     VBAT    VBATTERY    int.    int.        2.00    1.50 V (3)
 
 (1) Depends on your hardware setup.
 (2) Obviously not correct, swapping R1 and R2 would make more sense.
+(3) F71872F/FG only.
 
 These values can be used as hints at best, as motherboard manufacturers
 are free to use a completely different setup. As a matter of fact, the
@@ -103,3 +114,38 @@ sensor. Each channel can be used for connecting either a thermal diode
 or a thermistor. The driver reports the currently selected mode, but
 doesn't allow changing it. In theory, the BIOS should have configured
 everything properly.
+
+
+Fan Control
+-----------
+
+Both PWM (pulse-width modulation) and DC fan speed control methods are
+supported. The right one to use depends on external circuitry on the
+motherboard, so the driver assumes that the BIOS set the method
+properly. The driver will report the method, but won't let you change
+it.
+
+When the PWM method is used, you can select the operating frequency,
+from 187.5 kHz (default) to 31 Hz. The best frequency depends on the
+fan model. As a rule of thumb, lower frequencies seem to give better
+control, but may generate annoying high-pitch noise. Fintek recommends
+not going below 1 kHz, as the fan tachometers get confused by lower
+frequencies as well.
+
+When the DC method is used, Fintek recommends not going below 5 V, which
+corresponds to a pwm value of 106 for the driver. The driver doesn't
+enforce this limit though.
+
+Three different fan control modes are supported:
+
+* Manual mode
+  You ask for a specific PWM duty cycle or DC voltage.
+
+* Fan speed mode
+  You ask for a specific fan speed. This mode assumes that pwm1
+  corresponds to fan1, pwm2 to fan2 and pwm3 to fan3.
+
+* Temperature mode
+  You define 3 temperature/fan speed trip points, and the fan speed is
+  adjusted depending on the measured temperature, using interpolation.
+  This mode is not yet supported by the driver.
diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index e783fd62e30..74a80992d23 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -9,8 +9,7 @@ Supported chips:
                http://www.ite.com.tw/
   * IT8712F
     Prefix: 'it8712'
-    Addresses scanned: I2C 0x2d
-                       from Super I/O config space (8 I/O ports)
+    Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Publicly available at the ITE website
                http://www.ite.com.tw/
   * IT8716F
@@ -53,6 +52,18 @@ Module Parameters
   misconfigured by BIOS - PWM values would be inverted. This option tries
   to fix this. Please contact your BIOS manufacturer and ask him for fix.
 
+
+Hardware Interfaces
+-------------------
+
+All the chips suported by this driver are LPC Super-I/O chips, accessed
+through the LPC bus (ISA-like I/O ports). The IT8712F additionally has an
+SMBus interface to the hardware monitoring functions. This driver no
+longer supports this interface though, as it is slower and less reliable
+than the ISA access, and was only available on a small number of
+motherboard models.
+
+
 Description
 -----------
 
diff --git a/Documentation/hwmon/k8temp b/Documentation/hwmon/k8temp
index 30d123b8d92..0005c716614 100644
--- a/Documentation/hwmon/k8temp
+++ b/Documentation/hwmon/k8temp
@@ -8,7 +8,7 @@ Supported chips:
     Datasheet: http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/32559.pdf
 
 Author: Rudolf Marek
-Contact: Rudolf Marek <r.marek@sh.cvut.cz>
+Contact: Rudolf Marek <r.marek@assembler.cz>
 
 Description
 -----------
diff --git a/Documentation/hwmon/pc87427 b/Documentation/hwmon/pc87427
new file mode 100644
index 00000000000..9a0708f9f49
--- /dev/null
+++ b/Documentation/hwmon/pc87427
@@ -0,0 +1,38 @@
+Kernel driver pc87427
+=====================
+
+Supported chips:
+  * National Semiconductor PC87427
+    Prefix: 'pc87427'
+    Addresses scanned: none, address read from Super I/O config space
+    Datasheet: http://www.winbond.com.tw/E-WINBONDHTM/partner/apc_007.html
+
+Author: Jean Delvare <khali@linux-fr.org>
+
+Thanks to Amir Habibi at Candelis for setting up a test system, and to
+Michael Kress for testing several iterations of this driver.
+
+
+Description
+-----------
+
+The National Semiconductor Super I/O chip includes complete hardware
+monitoring capabilities. It can monitor up to 18 voltages, 8 fans and
+6 temperature sensors. Only the fans are supported at the moment.
+
+This chip also has fan controlling features, which are not yet supported
+by this driver either.
+
+The driver assumes that no more than one chip is present, which seems
+reasonable.
+
+
+Fan Monitoring
+--------------
+
+Fan rotation speeds are reported as 14-bit values from a gated clock
+signal. Speeds down to 83 RPM can be measured.
+
+An alarm is triggered if the rotation speed drops below a programmable
+limit. Another alarm is triggered if the speed is too low to to be measured
+(including stalled or missing fan).
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index d1d390aaf62..efef3b962cd 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -208,12 +208,14 @@ temp[1-*]_auto_point[1-*]_temp_hyst
 ****************
 
 temp[1-*]_type	Sensor type selection.
-		Integers 1 to 4 or thermistor Beta value (typically 3435)
+		Integers 1 to 6 or thermistor Beta value (typically 3435)
 		RW
 		1: PII/Celeron Diode
 		2: 3904 transistor
 		3: thermal diode
 		4: thermistor (default/unknown Beta)
+		5: AMD AMDSI
+		6: Intel PECI
 		Not all types are supported by all chips
 
 temp[1-*]_max	Temperature max value.
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index caa610a297e..8a15a740875 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -10,7 +10,7 @@ Supported chips:
 Authors:
         Jean Delvare <khali@linux-fr.org>
         Yuan Mu (Winbond)
-        Rudolf Marek <r.marek@sh.cvut.cz>
+        Rudolf Marek <r.marek@assembler.cz>
 
 Description
 -----------
diff --git a/Documentation/hwmon/w83791d b/Documentation/hwmon/w83791d
index 19b2ed739fa..db9881df88a 100644
--- a/Documentation/hwmon/w83791d
+++ b/Documentation/hwmon/w83791d
@@ -18,7 +18,7 @@ Credits:
     and Mark Studebaker <mdsxyz123@yahoo.com>
   w83792d.c:
     Chunhao Huang <DZShen@Winbond.com.tw>,
-    Rudolf Marek <r.marek@sh.cvut.cz>
+    Rudolf Marek <r.marek@assembler.cz>
 
 Additional contributors:
     Sven Anders <anders@anduras.de>
diff --git a/Documentation/hwmon/w83793 b/Documentation/hwmon/w83793
new file mode 100644
index 00000000000..51171a83165
--- /dev/null
+++ b/Documentation/hwmon/w83793
@@ -0,0 +1,106 @@
+Kernel driver w83793
+====================
+
+Supported chips:
+  * Winbond W83793G/W83793R
+    Prefix: 'w83793'
+    Addresses scanned: I2C 0x2c - 0x2f
+    Datasheet: Still not published
+
+Authors:
+    Yuan Mu (Winbond Electronics)
+    Rudolf Marek <r.marek@assembler.cz>
+
+
+Module parameters
+-----------------
+
+* reset int
+  (default 0)
+  This parameter is not recommended, it will lose motherboard specific
+  settings. Use 'reset=1' to reset the chip when loading this module.
+
+* force_subclients=bus,caddr,saddr1,saddr2
+  This is used to force the i2c addresses for subclients of
+  a certain chip. Typical usage is `force_subclients=0,0x2f,0x4a,0x4b'
+  to force the subclients of chip 0x2f on bus 0 to i2c addresses
+  0x4a and 0x4b.
+
+
+Description
+-----------
+
+This driver implements support for Winbond W83793G/W83793R chips.
+
+* Exported features
+  This driver exports 10 voltage sensors, up to 12 fan tachometer inputs,
+  6 remote temperatures, up to 8 sets of PWM fan controls, SmartFan
+  (automatic fan speed control) on all temperature/PWM combinations, 2
+  sets of 6-pin CPU VID input.
+
+* Sensor resolutions
+  If your motherboard maker used the reference design, the resolution of
+  voltage0-2 is 2mV, resolution of voltage3/4/5 is 16mV, 8mV for voltage6,
+  24mV for voltage7/8. Temp1-4 have a 0.25 degree Celsius resolution,
+  temp5-6 have a 1 degree Celsiis resolution.
+
+* Temperature sensor types
+  Temp1-4 have 2 possible types. It can be read from (and written to)
+  temp[1-4]_type.
+  - If the value is 3, it starts monitoring using a remote termal diode
+    (default).
+  - If the value is 6, it starts monitoring using the temperature sensor
+    in Intel CPU and get result by PECI.
+  Temp5-6 can be connected to external thermistors (value of
+  temp[5-6]_type is 4).
+
+* Alarm mechanism
+  For voltage sensors, an alarm triggers if the measured value is below
+  the low voltage limit or over the high voltage limit.
+  For temperature sensors, an alarm triggers if the measured value goes
+  above the high temperature limit, and wears off only after the measured
+  value drops below the hysteresis value.
+  For fan sensors, an alarm triggers if the measured value is below the
+  low speed limit.
+
+* SmartFan/PWM control
+  If you want to set a pwm fan to manual mode, you just need to make sure it
+  is not controlled by any temp channel, for example, you want to set fan1
+  to manual mode, you need to check the value of temp[1-6]_fan_map, make
+  sure bit 0 is cleared in the 6 values. And then set the pwm1 value to
+  control the fan.
+
+  Each temperature channel can control all the 8 PWM outputs (by setting the
+  corresponding bit in tempX_fan_map), you can set the temperature channel
+  mode using temp[1-6]_pwm_enable, 2 is Thermal Cruise mode and 3
+  is the SmartFanII mode. Temperature channels will try to speed up or
+  slow down all controlled fans, this means one fan can receive different
+  PWM value requests from different temperature channels, but the chip
+  will always pick the safest (max) PWM value for each fan.
+
+  In Thermal Cruise mode, the chip attempts to keep the temperature at a
+  predefined value, within a tolerance margin. So if tempX_input >
+  thermal_cruiseX + toleranceX, the chip will increase the PWM value,
+  if tempX_input < thermal_cruiseX - toleranceX, the chip will decrease
+  the PWM value. If the temperature is within the tolerance range, the PWM
+  value is left unchanged.
+
+  SmartFanII works differently, you have to define up to 7 PWM, temperature
+  trip points, defining a PWM/temperature curve which the chip will follow.
+  While not fundamentally different from the Thermal Cruise mode, the
+  implementation is quite different, giving you a finer-grained control.
+
+* Chassis
+  If the case open alarm triggers, it will stay in this state unless cleared
+  by any write to the sysfs file "chassis".
+
+* VID and VRM
+  The VRM version is detected automatically, don't modify the it unless you
+  *do* know the cpu VRM version and it's not properly detected.
+
+
+Notes
+-----
+
+  Only Fan1-5 and PWM1-3 are guaranteed to always exist, other fan inputs and
+  PWM outputs may or may not exist depending on the chip pin configuration.