Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
  net: Allow dependancies of FDDI & Tokenring to be modular.
  igb: Fix build warning when DCA is disabled.
  net: Fix warning fallout from recent NAPI interface changes.
  gro: Fix potential use after free
  sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
  sfc: When disabling the NIC, close the device rather than unregistering it
  sfc: SFT9001: Add cable diagnostics
  sfc: Add support for multiple PHY self-tests
  sfc: Merge top-level functions for self-tests
  sfc: Clean up PHY mode management in loopback self-test
  sfc: Fix unreliable link detection in some loopback modes
  sfc: Generate unique names for per-NIC workqueues
  802.3ad: use standard ethhdr instead of ad_header
  802.3ad: generalize out mac address initializer
  802.3ad: initialize ports LACPDU from const initializer
  802.3ad: remove typedef around ad_system
  802.3ad: turn ports is_individual into a bool
  802.3ad: turn ports is_enabled into a bool
  802.3ad: make ntt bool
  ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
  ...

Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).

1 files changed, 21 insertions, 11 deletions

diff --git a/Documentation/networking/dccp.txt b/Documentation/networking/dccp.txt
index 39131a3c78f..7a3bb1abb83 100644
--- a/Documentation/networking/dccp.txt
+++ b/Documentation/networking/dccp.txt
@@ -57,6 +57,24 @@ can be set before calling bind().
 DCCP_SOCKOPT_GET_CUR_MPS is read-only and retrieves the current maximum packet
 size (application payload size) in bytes, see RFC 4340, section 14.
 
+DCCP_SOCKOPT_AVAILABLE_CCIDS is also read-only and returns the list of CCIDs
+supported by the endpoint (see include/linux/dccp.h for symbolic constants).
+The caller needs to provide a sufficiently large (> 2) array of type uint8_t.
+
+DCCP_SOCKOPT_CCID is write-only and sets both the TX and RX CCIDs at the same
+time, combining the operation of the next two socket options. This option is
+preferrable over the latter two, since often applications will use the same
+type of CCID for both directions; and mixed use of CCIDs is not currently well
+understood. This socket option takes as argument at least one uint8_t value, or
+an array of uint8_t values, which must match available CCIDS (see above). CCIDs
+must be registered on the socket before calling connect() or listen().
+
+DCCP_SOCKOPT_TX_CCID is read/write. It returns the current CCID (if set) or sets
+the preference list for the TX CCID, using the same format as DCCP_SOCKOPT_CCID.
+Please note that the getsockopt argument type here is `int', not uint8_t.
+
+DCCP_SOCKOPT_RX_CCID is analogous to DCCP_SOCKOPT_TX_CCID, but for the RX CCID.
+
 DCCP_SOCKOPT_SERVER_TIMEWAIT enables the server (listening socket) to hold
 timewait state when closing the connection (RFC 4340, 8.3). The usual case is
 that the closing server sends a CloseReq, whereupon the client holds timewait
@@ -115,20 +133,12 @@ retries2
 	importance for retransmitted acknowledgments and feature negotiation,
 	data packets are never retransmitted. Analogue of tcp_retries2.
 
-send_ndp = 1
-	Whether or not to send NDP count options (sec. 7.7.2).
-
-send_ackvec = 1
-	Whether or not to send Ack Vector options (sec. 11.5).
-
-ack_ratio = 2
-	The default Ack Ratio (sec. 11.3) to use.
-
 tx_ccid = 2
-	Default CCID for the sender-receiver half-connection.
+	Default CCID for the sender-receiver half-connection. Depending on the
+	choice of CCID, the Send Ack Vector feature is enabled automatically.
 
 rx_ccid = 2
-	Default CCID for the receiver-sender half-connection.
+	Default CCID for the receiver-sender half-connection; see tx_ccid.
 
 seq_window = 100
 	The initial sequence window (sec. 7.5.2).