Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel

18 files changed, 1812 insertions, 164 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 3754b79092a..64ab386a65c 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -58,4 +58,12 @@ config MACH_OVERO
 
 config MACH_OMAP3_PANDORA
 	bool "OMAP3 Pandora"
-	depends on ARCH_OMAP3 && ARCH_OMAP34XX
\ No newline at end of file
+	depends on ARCH_OMAP3 && ARCH_OMAP34XX
+
+config MACH_OMAP_3430SDP
+	bool "OMAP 3430 SDP board"
+	depends on ARCH_OMAP3 && ARCH_OMAP34XX
+
+config MACH_NOKIA_RX51
+	bool "Nokia RX-51 board"
+	depends on ARCH_OMAP3 && ARCH_OMAP34XX
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 9717afcdbda..a2c3fcc27a2 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -42,4 +42,12 @@ obj-$(CONFIG_MACH_OVERO)		+= board-overo.o \
 					   mmc-twl4030.o
 obj-$(CONFIG_MACH_OMAP3_PANDORA)	+= board-omap3pandora.o \
 					   mmc-twl4030.o
+obj-$(CONFIG_MACH_OMAP_3430SDP)		+= board-3430sdp.o \
+					   mmc-twl4030.o
 
+obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o \
+					   board-rx51-peripherals.o \
+# Platform specific device init code
+ifeq ($(CONFIG_USB_MUSB_SOC),y)
+obj-y					+= usb-musb.o
+endif
diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c
index 7b29e1d00f2..22143651037 100644
--- a/arch/arm/mach-omap2/board-2430sdp.c
+++ b/arch/arm/mach-omap2/board-2430sdp.c
@@ -35,12 +35,16 @@
 #include <mach/board.h>
 #include <mach/common.h>
 #include <mach/gpmc.h>
+#include <mach/usb.h>
 
 #include "mmc-twl4030.h"
 
+#define SDP2430_CS0_BASE	0x04000000
 #define	SDP2430_FLASH_CS	0
 #define	SDP2430_SMC91X_CS	5
 
+#define SDP2430_ETHR_GPIO_IRQ		149
+
 static struct mtd_partition sdp2430_partitions[] = {
 	/* bootloader (U-Boot, etc) in first sector */
 	{
@@ -102,8 +106,8 @@ static struct resource sdp2430_smc91x_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= OMAP_GPIO_IRQ(OMAP24XX_ETHR_GPIO_IRQ),
-		.end	= OMAP_GPIO_IRQ(OMAP24XX_ETHR_GPIO_IRQ),
+		.start	= OMAP_GPIO_IRQ(SDP2430_ETHR_GPIO_IRQ),
+		.end	= OMAP_GPIO_IRQ(SDP2430_ETHR_GPIO_IRQ),
 		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 	},
 };
@@ -170,13 +174,13 @@ static inline void __init sdp2430_init_smc91x(void)
 	sdp2430_smc91x_resources[0].end = cs_mem_base + 0x30f;
 	udelay(100);
 
-	if (gpio_request(OMAP24XX_ETHR_GPIO_IRQ, "SMC91x irq") < 0) {
+	if (gpio_request(SDP2430_ETHR_GPIO_IRQ, "SMC91x irq") < 0) {
 		printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
-			OMAP24XX_ETHR_GPIO_IRQ);
+			SDP2430_ETHR_GPIO_IRQ);
 		gpmc_cs_free(eth_cs);
 		goto out;
 	}
-	gpio_direction_input(OMAP24XX_ETHR_GPIO_IRQ);
+	gpio_direction_input(SDP2430_ETHR_GPIO_IRQ);
 
 out:
 	clk_disable(gpmc_fck);
@@ -251,6 +255,7 @@ static void __init omap_2430sdp_init(void)
 	omap_board_config_size = ARRAY_SIZE(sdp2430_config);
 	omap_serial_init();
 	twl4030_mmc_init(mmc);
+	usb_musb_init();
 }
 
 static void __init omap_2430sdp_map_io(void)
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
new file mode 100644
index 00000000000..2af38e56db3
--- /dev/null
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -0,0 +1,542 @@
+/*
+ * linux/arch/arm/mach-omap2/board-3430sdp.c
+ *
+ * Copyright (C) 2007 Texas Instruments
+ *
+ * Modified from mach-omap2/board-generic.c
+ *
+ * Initial code: Syed Mohammed Khasim
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/input.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/i2c/twl4030.h>
+#include <linux/regulator/machine.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/mcspi.h>
+#include <mach/mux.h>
+#include <mach/board.h>
+#include <mach/usb.h>
+#include <mach/common.h>
+#include <mach/dma.h>
+#include <mach/gpmc.h>
+
+#include <mach/control.h>
+#include <mach/keypad.h>
+
+#include "mmc-twl4030.h"
+
+#define CONFIG_DISABLE_HFCLK 1
+
+#define SDP3430_ETHR_GPIO_IRQ_SDPV1	29
+#define SDP3430_ETHR_GPIO_IRQ_SDPV2	6
+#define SDP3430_SMC91X_CS		3
+
+#define SDP3430_TS_GPIO_IRQ_SDPV1	3
+#define SDP3430_TS_GPIO_IRQ_SDPV2	2
+
+#define ENABLE_VAUX3_DEDICATED	0x03
+#define ENABLE_VAUX3_DEV_GRP	0x20
+
+#define TWL4030_MSECURE_GPIO 22
+
+static struct resource sdp3430_smc91x_resources[] = {
+	[0] = {
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= 0,
+		.end	= 0,
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+	},
+};
+
+static struct platform_device sdp3430_smc91x_device = {
+	.name		= "smc91x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(sdp3430_smc91x_resources),
+	.resource	= sdp3430_smc91x_resources,
+};
+
+static int sdp3430_keymap[] = {
+	KEY(0, 0, KEY_LEFT),
+	KEY(0, 1, KEY_RIGHT),
+	KEY(0, 2, KEY_A),
+	KEY(0, 3, KEY_B),
+	KEY(0, 4, KEY_C),
+	KEY(1, 0, KEY_DOWN),
+	KEY(1, 1, KEY_UP),
+	KEY(1, 2, KEY_E),
+	KEY(1, 3, KEY_F),
+	KEY(1, 4, KEY_G),
+	KEY(2, 0, KEY_ENTER),
+	KEY(2, 1, KEY_I),
+	KEY(2, 2, KEY_J),
+	KEY(2, 3, KEY_K),
+	KEY(2, 4, KEY_3),
+	KEY(3, 0, KEY_M),
+	KEY(3, 1, KEY_N),
+	KEY(3, 2, KEY_O),
+	KEY(3, 3, KEY_P),
+	KEY(3, 4, KEY_Q),
+	KEY(4, 0, KEY_R),
+	KEY(4, 1, KEY_4),
+	KEY(4, 2, KEY_T),
+	KEY(4, 3, KEY_U),
+	KEY(4, 4, KEY_D),
+	KEY(5, 0, KEY_V),
+	KEY(5, 1, KEY_W),
+	KEY(5, 2, KEY_L),
+	KEY(5, 3, KEY_S),
+	KEY(5, 4, KEY_H),
+	0
+};
+
+static struct twl4030_keypad_data sdp3430_kp_data = {
+	.rows		= 5,
+	.cols		= 6,
+	.keymap		= sdp3430_keymap,
+	.keymapsize	= ARRAY_SIZE(sdp3430_keymap),
+	.rep		= 1,
+};
+
+static int ts_gpio;	/* Needed for ads7846_get_pendown_state */
+
+/**
+ * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
+ *
+ * @return - void. If request gpio fails then Flag KERN_ERR.
+ */
+static void ads7846_dev_init(void)
+{
+	if (gpio_request(ts_gpio, "ADS7846 pendown") < 0) {
+		printk(KERN_ERR "can't get ads746 pen down GPIO\n");
+		return;
+	}
+
+	gpio_direction_input(ts_gpio);
+
+	omap_set_gpio_debounce(ts_gpio, 1);
+	omap_set_gpio_debounce_time(ts_gpio, 0xa);
+}
+
+static int ads7846_get_pendown_state(void)
+{
+	return !gpio_get_value(ts_gpio);
+}
+
+static struct ads7846_platform_data tsc2046_config __initdata = {
+	.get_pendown_state	= ads7846_get_pendown_state,
+	.keep_vref_on		= 1,
+};
+
+
+static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
+	.turbo_mode	= 0,
+	.single_channel	= 1,	/* 0: slave, 1: master */
+};
+
+static struct spi_board_info sdp3430_spi_board_info[] __initdata = {
+	[0] = {
+		/*
+		 * TSC2046 operates at a max freqency of 2MHz, so
+		 * operate slightly below at 1.5MHz
+		 */
+		.modalias		= "ads7846",
+		.bus_num		= 1,
+		.chip_select		= 0,
+		.max_speed_hz		= 1500000,
+		.controller_data	= &tsc2046_mcspi_config,
+		.irq			= 0,
+		.platform_data		= &tsc2046_config,
+	},
+};
+
+static struct platform_device sdp3430_lcd_device = {
+	.name		= "sdp2430_lcd",
+	.id		= -1,
+};
+
+static struct regulator_consumer_supply sdp3430_vdac_supply = {
+	.supply		= "vdac",
+	.dev		= &sdp3430_lcd_device.dev,
+};
+
+static struct regulator_consumer_supply sdp3430_vdvi_supply = {
+	.supply		= "vdvi",
+	.dev		= &sdp3430_lcd_device.dev,
+};
+
+static struct platform_device *sdp3430_devices[] __initdata = {
+	&sdp3430_smc91x_device,
+	&sdp3430_lcd_device,
+};
+
+static inline void __init sdp3430_init_smc91x(void)
+{
+	int eth_cs;
+	unsigned long cs_mem_base;
+	int eth_gpio = 0;
+
+	eth_cs = SDP3430_SMC91X_CS;
+
+	if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
+		printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
+		return;
+	}
+
+	sdp3430_smc91x_resources[0].start = cs_mem_base + 0x300;
+	sdp3430_smc91x_resources[0].end = cs_mem_base + 0x30f;
+	udelay(100);
+
+	if (omap_rev() > OMAP3430_REV_ES1_0)
+		eth_gpio = SDP3430_ETHR_GPIO_IRQ_SDPV2;
+	else
+		eth_gpio = SDP3430_ETHR_GPIO_IRQ_SDPV1;
+
+	sdp3430_smc91x_resources[1].start = gpio_to_irq(eth_gpio);
+
+	if (gpio_request(eth_gpio, "SMC91x irq") < 0) {
+		printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
+			eth_gpio);
+		return;
+	}
+	gpio_direction_input(eth_gpio);
+}
+
+static void __init omap_3430sdp_init_irq(void)
+{
+	omap2_init_common_hw();
+	omap_init_irq();
+	omap_gpio_init();
+	sdp3430_init_smc91x();
+}
+
+static struct omap_uart_config sdp3430_uart_config __initdata = {
+	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
+static struct omap_lcd_config sdp3430_lcd_config __initdata = {
+	.ctrl_name	= "internal",
+};
+
+static struct omap_board_config_kernel sdp3430_config[] __initdata = {
+	{ OMAP_TAG_UART,	&sdp3430_uart_config },
+	{ OMAP_TAG_LCD,		&sdp3430_lcd_config },
+};
+
+static int sdp3430_batt_table[] = {
+/* 0 C*/
+30800, 29500, 28300, 27100,
+26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900,
+17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100,
+11600, 11200, 10800, 10400, 10000, 9630,   9280,   8950,   8620,   8310,
+8020,   7730,   7460,   7200,   6950,   6710,   6470,   6250,   6040,   5830,
+5640,   5450,   5260,   5090,   4920,   4760,   4600,   4450,   4310,   4170,
+4040,   3910,   3790,   3670,   3550
+};
+
+static struct twl4030_bci_platform_data sdp3430_bci_data = {
+	.battery_tmp_tbl	= sdp3430_batt_table,
+	.tblsize		= ARRAY_SIZE(sdp3430_batt_table),
+};
+
+static struct twl4030_hsmmc_info mmc[] = {
+	{
+		.mmc		= 1,
+		/* 8 bits (default) requires S6.3 == ON,
+		 * so the SIM card isn't used; else 4 bits.
+		 */
+		.wires		= 8,
+		.gpio_wp	= 4,
+	},
+	{
+		.mmc		= 2,
+		.wires		= 8,
+		.gpio_wp	= 7,
+	},
+	{}	/* Terminator */
+};
+
+static struct regulator_consumer_supply sdp3430_vmmc1_supply = {
+	.supply			= "vmmc",
+};
+
+static struct regulator_consumer_supply sdp3430_vsim_supply = {
+	.supply			= "vmmc_aux",
+};
+
+static struct regulator_consumer_supply sdp3430_vmmc2_supply = {
+	.supply			= "vmmc",
+};
+
+static int sdp3430_twl_gpio_setup(struct device *dev,
+		unsigned gpio, unsigned ngpio)
+{
+	/* gpio + 0 is "mmc0_cd" (input/IRQ),
+	 * gpio + 1 is "mmc1_cd" (input/IRQ)
+	 */
+	mmc[0].gpio_cd = gpio + 0;
+	mmc[1].gpio_cd = gpio + 1;
+	twl4030_mmc_init(mmc);
+
+	/* link regulators to MMC adapters ... we "know" the
+	 * regulators will be set up only *after* we return.
+	 */
+	sdp3430_vmmc1_supply.dev = mmc[0].dev;
+	sdp3430_vsim_supply.dev = mmc[0].dev;
+	sdp3430_vmmc2_supply.dev = mmc[1].dev;
+
+	/* gpio + 7 is "sub_lcd_en_bkl" (output/PWM1) */
+	gpio_request(gpio + 7, "sub_lcd_en_bkl");
+	gpio_direction_output(gpio + 7, 0);
+
+	/* gpio + 15 is "sub_lcd_nRST" (output) */
+	gpio_request(gpio + 15, "sub_lcd_nRST");
+	gpio_direction_output(gpio + 15, 0);
+
+	return 0;
+}
+
+static struct twl4030_gpio_platform_data sdp3430_gpio_data = {
+	.gpio_base	= OMAP_MAX_GPIO_LINES,
+	.irq_base	= TWL4030_GPIO_IRQ_BASE,
+	.irq_end	= TWL4030_GPIO_IRQ_END,
+	.pulldowns	= BIT(2) | BIT(6) | BIT(8) | BIT(13)
+				| BIT(16) | BIT(17),
+	.setup		= sdp3430_twl_gpio_setup,
+};
+
+static struct twl4030_usb_data sdp3430_usb_data = {
+	.usb_mode	= T2_USB_MODE_ULPI,
+};
+
+static struct twl4030_madc_platform_data sdp3430_madc_data = {
+	.irq_line	= 1,
+};
+
+/*
+ * Apply all the fixed voltages since most versions of U-Boot
+ * don't bother with that initialization.
+ */
+
+/* VAUX1 for mainboard (irda and sub-lcd) */
+static struct regulator_init_data sdp3430_vaux1 = {
+	.constraints = {
+		.min_uV			= 2800000,
+		.max_uV			= 2800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+/* VAUX2 for camera module */
+static struct regulator_init_data sdp3430_vaux2 = {
+	.constraints = {
+		.min_uV			= 2800000,
+		.max_uV			= 2800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+/* VAUX3 for LCD board */
+static struct regulator_init_data sdp3430_vaux3 = {
+	.constraints = {
+		.min_uV			= 2800000,
+		.max_uV			= 2800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+/* VAUX4 for OMAP VDD_CSI2 (camera) */
+static struct regulator_init_data sdp3430_vaux4 = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
+static struct regulator_init_data sdp3430_vmmc1 = {
+	.constraints = {
+		.min_uV			= 1850000,
+		.max_uV			= 3150000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &sdp3430_vmmc1_supply,
+};
+
+/* VMMC2 for MMC2 card */
+static struct regulator_init_data sdp3430_vmmc2 = {
+	.constraints = {
+		.min_uV			= 1850000,
+		.max_uV			= 1850000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &sdp3430_vmmc2_supply,
+};
+
+/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */
+static struct regulator_init_data sdp3430_vsim = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 3000000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &sdp3430_vsim_supply,
+};
+
+/* VDAC for DSS driving S-Video */
+static struct regulator_init_data sdp3430_vdac = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &sdp3430_vdac_supply,
+};
+
+/* VPLL2 for digital video outputs */
+static struct regulator_init_data sdp3430_vpll2 = {
+	.constraints = {
+		.name			= "VDVI",
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &sdp3430_vdvi_supply,
+};
+
+static struct twl4030_platform_data sdp3430_twldata = {
+	.irq_base	= TWL4030_IRQ_BASE,
+	.irq_end	= TWL4030_IRQ_END,
+
+	/* platform_data for children goes here */
+	.bci		= &sdp3430_bci_data,
+	.gpio		= &sdp3430_gpio_data,
+	.madc		= &sdp3430_madc_data,
+	.keypad		= &sdp3430_kp_data,
+	.usb		= &sdp3430_usb_data,
+
+	.vaux1		= &sdp3430_vaux1,
+	.vaux2		= &sdp3430_vaux2,
+	.vaux3		= &sdp3430_vaux3,
+	.vaux4		= &sdp3430_vaux4,
+	.vmmc1		= &sdp3430_vmmc1,
+	.vmmc2		= &sdp3430_vmmc2,
+	.vsim		= &sdp3430_vsim,
+	.vdac		= &sdp3430_vdac,
+	.vpll2		= &sdp3430_vpll2,
+};
+
+static struct i2c_board_info __initdata sdp3430_i2c_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("twl4030", 0x48),
+		.flags = I2C_CLIENT_WAKE,
+		.irq = INT_34XX_SYS_NIRQ,
+		.platform_data = &sdp3430_twldata,
+	},
+};
+
+static int __init omap3430_i2c_init(void)
+{
+	/* i2c1 for PMIC only */
+	omap_register_i2c_bus(1, 2600, sdp3430_i2c_boardinfo,
+			ARRAY_SIZE(sdp3430_i2c_boardinfo));
+	/* i2c2 on camera connector (for sensor control) and optional isp1301 */
+	omap_register_i2c_bus(2, 400, NULL, 0);
+	/* i2c3 on display connector (for DVI, tfp410) */
+	omap_register_i2c_bus(3, 400, NULL, 0);
+	return 0;
+}
+
+static void __init omap_3430sdp_init(void)
+{
+	omap3430_i2c_init();
+	platform_add_devices(sdp3430_devices, ARRAY_SIZE(sdp3430_devices));
+	omap_board_config = sdp3430_config;
+	omap_board_config_size = ARRAY_SIZE(sdp3430_config);
+	if (omap_rev() > OMAP3430_REV_ES1_0)
+		ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV2;
+	else
+		ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV1;
+	sdp3430_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
+	spi_register_board_info(sdp3430_spi_board_info,
+				ARRAY_SIZE(sdp3430_spi_board_info));
+	ads7846_dev_init();
+	omap_serial_init();
+	usb_musb_init();
+}
+
+static void __init omap_3430sdp_map_io(void)
+{
+	omap2_set_globals_343x();
+	omap2_map_common_io();
+}
+
+MACHINE_START(OMAP_3430SDP, "OMAP3430 3430SDP board")
+	/* Maintainer: Syed Khasim - Texas Instruments Inc */
+	.phys_io	= 0x48000000,
+	.io_pg_offst	= ((0xd8000000) >> 18) & 0xfffc,
+	.boot_params	= 0x80000100,
+	.map_io		= omap_3430sdp_map_io,
+	.init_irq	= omap_3430sdp_init_irq,
+	.init_machine	= omap_3430sdp_init,
+	.timer		= &omap_timer,
+MACHINE_END
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 0c911f414d8..06dfba888b0 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -51,6 +51,7 @@
 
 #define APOLLON_FLASH_CS	0
 #define APOLLON_ETH_CS		1
+#define APOLLON_ETHR_GPIO_IRQ	74
 
 static struct mtd_partition apollon_partitions[] = {
 	{
@@ -272,7 +273,6 @@ static struct omap_lcd_config apollon_lcd_config __initdata = {
 
 static struct omap_board_config_kernel apollon_config[] = {
 	{ OMAP_TAG_UART,	&apollon_uart_config },
-	{ OMAP_TAG_USB,		&apollon_usb_config },
 	{ OMAP_TAG_LCD,		&apollon_lcd_config },
 };
 
@@ -299,6 +299,7 @@ static void __init apollon_usb_init(void)
 	omap_cfg_reg(P21_242X_GPIO12);
 	gpio_request(12, "USB suspend");
 	gpio_direction_output(12, 0);
+	omap_usb_init(&apollon_usb_config);
 }
 
 static void __init omap_apollon_init(void)
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index ef55b45ab76..a0267a9ab46 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -47,6 +47,8 @@
 #define H4_FLASH_CS	0
 #define H4_SMC91X_CS	1
 
+#define H4_ETHR_GPIO_IRQ		92
+
 static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
 static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };
 
@@ -341,7 +343,7 @@ static inline void __init h4_init_debug(void)
 	udelay(100);
 
 	omap_cfg_reg(M15_24XX_GPIO92);
-	if (debug_card_init(cs_mem_base, OMAP24XX_ETHR_GPIO_IRQ) < 0)
+	if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0)
 		gpmc_cs_free(eth_cs);
 
 out:
@@ -377,6 +379,39 @@ static struct omap_lcd_config h4_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
+static struct omap_usb_config h4_usb_config __initdata = {
+#ifdef	CONFIG_MACH_OMAP2_H4_USB1
+	/* NOTE:  usb1 could also be used with 3 wire signaling */
+	.pins[1]	= 4,
+#endif
+
+#ifdef	CONFIG_MACH_OMAP_H4_OTG
+	/* S1.10 ON -- USB OTG port
+	 * usb0 switched to Mini-AB port and isp1301 transceiver;
+	 * S2.POS3 = OFF, S2.POS4 = ON ... to allow battery charging
+	 */
+	.otg		= 1,
+	.pins[0]	= 4,
+#ifdef	CONFIG_USB_GADGET_OMAP
+	/* use OTG cable, or standard A-to-MiniB */
+	.hmc_mode	= 0x14,	/* 0:dev/otg 1:host 2:disable */
+#elif	defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+	/* use OTG cable, or NONSTANDARD (B-to-MiniB) */
+	.hmc_mode	= 0x11,	/* 0:host 1:host 2:disable */
+#endif	/* XX */
+
+#else
+	/* S1.10 OFF -- usb "download port"
+	 * usb0 switched to Mini-B port and isp1105 transceiver;
+	 * S2.POS3 = ON, S2.POS4 = OFF ... to enable battery charging
+	 */
+	.register_dev	= 1,
+	.pins[0]	= 3,
+/*	.hmc_mode	= 0x14,*/	/* 0:dev 1:host 2:disable */
+	.hmc_mode	= 0x00,		/* 0:dev|otg 1:disable 2:disable */
+#endif
+};
+
 static struct omap_board_config_kernel h4_config[] = {
 	{ OMAP_TAG_UART,	&h4_uart_config },
 	{ OMAP_TAG_LCD,		&h4_lcd_config },
@@ -428,6 +463,7 @@ static void __init omap_h4_init(void)
 	platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
 	omap_board_config = h4_config;
 	omap_board_config_size = ARRAY_SIZE(h4_config);
+	omap_usb_init(&h4_usb_config);
 	omap_serial_init();
 }
 
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index c71580557c6..e096f776f99 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -29,7 +29,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/board-ldp.h>
 #include <mach/mcspi.h>
 #include <mach/gpio.h>
 #include <mach/board.h>
@@ -38,15 +37,19 @@
 
 #include <asm/delay.h>
 #include <mach/control.h>
+#include <mach/usb.h>
 
 #include "mmc-twl4030.h"
 
-#define SDP3430_SMC91X_CS	3
+#define LDP_SMC911X_CS		1
+#define LDP_SMC911X_GPIO	152
+#define DEBUG_BASE		0x08000000
+#define LDP_ETHR_START		DEBUG_BASE
 
 static struct resource ldp_smc911x_resources[] = {
 	[0] = {
-		.start	= OMAP34XX_ETHR_START,
-		.end	= OMAP34XX_ETHR_START + SZ_4K,
+		.start	= LDP_ETHR_START,
+		.end	= LDP_ETHR_START + SZ_4K,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
@@ -162,6 +165,7 @@ static void __init omap_ldp_init(void)
 	omap_board_config_size = ARRAY_SIZE(ldp_config);
 	omap_serial_init();
 	twl4030_mmc_init(mmc);
+	usb_musb_init();
 }
 
 static void __init omap_ldp_map_io(void)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index b70b1e65034..744740ae1b9 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -41,6 +41,7 @@
 #include <mach/gpmc.h>
 #include <mach/nand.h>
 #include <mach/mux.h>
+#include <mach/usb.h>
 
 #include "mmc-twl4030.h"
 
@@ -175,9 +176,6 @@ static int __init omap3_beagle_i2c_init(void)
 {
 	omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
 			ARRAY_SIZE(beagle_i2c_boardinfo));
-#ifdef CONFIG_I2C2_OMAP_BEAGLE
-	omap_register_i2c_bus(2, 400, NULL, 0);
-#endif
 	/* Bus 3 is attached to the DVI port where devices like the pico DLP
 	 * projector don't work reliably with 400kHz */
 	omap_register_i2c_bus(3, 100, NULL, 0);
@@ -316,6 +314,7 @@ static void __init omap3_beagle_init(void)
 	/* REVISIT leave DVI powered down until it's needed ... */
 	gpio_direction_output(170, true);
 
+	usb_musb_init();
 	omap3beagle_flash_init();
 }
 
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index b3196107afd..16e2128daa1 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -34,6 +34,7 @@
 #include <mach/gpio.h>
 #include <mach/hardware.h>
 #include <mach/mcspi.h>
+#include <mach/usb.h>
 
 #include "mmc-twl4030.h"
 
@@ -53,6 +54,13 @@ static struct twl4030_hsmmc_info omap3pandora_mmc[] = {
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 127,
 		.ext_clock	= 1,
+		.transceiver	= true,
+	},
+	{
+		.mmc		= 3,
+		.wires		= 4,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
 	},
 	{}	/* Terminator */
 };
@@ -193,6 +201,7 @@ static void __init omap3pandora_init(void)
 	spi_register_board_info(omap3pandora_spi_board_info,
 			ARRAY_SIZE(omap3pandora_spi_board_info));
 	omap3pandora_ads7846_init();
+	usb_musb_init();
 }
 
 static void __init omap3pandora_map_io(void)
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 82b3dc557c9..782268c9194 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -37,20 +37,85 @@
 #include <asm/mach/flash.h>
 #include <asm/mach/map.h>
 
-#include <mach/board-overo.h>
 #include <mach/board.h>
 #include <mach/common.h>
 #include <mach/gpio.h>
 #include <mach/gpmc.h>
 #include <mach/hardware.h>
 #include <mach/nand.h>
+#include <mach/usb.h>
 
 #include "mmc-twl4030.h"
 
+#define OVERO_GPIO_BT_XGATE	15
+#define OVERO_GPIO_W2W_NRESET	16
+#define OVERO_GPIO_BT_NRESET	164
+#define OVERO_GPIO_USBH_CPEN	168
+#define OVERO_GPIO_USBH_NRESET	183
+
 #define NAND_BLOCK_SIZE SZ_128K
 #define GPMC_CS0_BASE  0x60
 #define GPMC_CS_SIZE   0x30
 
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
+	defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+
+#include <mach/mcspi.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+
+static struct omap2_mcspi_device_config ads7846_mcspi_config = {
+	.turbo_mode	= 0,
+	.single_channel	= 1,	/* 0: slave, 1: master */
+};
+
+static int ads7846_get_pendown_state(void)
+{
+	return !gpio_get_value(OVERO_GPIO_PENDOWN);
+}
+
+static struct ads7846_platform_data ads7846_config = {
+	.x_max			= 0x0fff,
+	.y_max			= 0x0fff,
+	.x_plate_ohms		= 180,
+	.pressure_max		= 255,
+	.debounce_max		= 10,
+	.debounce_tol		= 3,
+	.debounce_rep		= 1,
+	.get_pendown_state	= ads7846_get_pendown_state,
+	.keep_vref_on		= 1,
+};
+
+static struct spi_board_info overo_spi_board_info[] __initdata = {
+	{
+		.modalias		= "ads7846",
+		.bus_num		= 1,
+		.chip_select		= 0,
+		.max_speed_hz		= 1500000,
+		.controller_data	= &ads7846_mcspi_config,
+		.irq			= OMAP_GPIO_IRQ(OVERO_GPIO_PENDOWN),
+		.platform_data		= &ads7846_config,
+	}
+};
+
+static void __init overo_ads7846_init(void)
+{
+	if ((gpio_request(OVERO_GPIO_PENDOWN, "ADS7846_PENDOWN") == 0) &&
+	    (gpio_direction_input(OVERO_GPIO_PENDOWN) == 0)) {
+		gpio_export(OVERO_GPIO_PENDOWN, 0);
+	} else {
+		printk(KERN_ERR "could not obtain gpio for ADS7846_PENDOWN\n");
+		return;
+	}
+
+	spi_register_board_info(overo_spi_board_info,
+			ARRAY_SIZE(overo_spi_board_info));
+}
+
+#else
+static inline void __init overo_ads7846_init(void) { return; }
+#endif
+
 static struct mtd_partition overo_nand_partitions[] = {
 	{
 		.name           = "xloader",
@@ -209,6 +274,7 @@ static struct twl4030_hsmmc_info mmc[] __initdata = {
 		.wires		= 4,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
+		.transceiver	= true,
 	},
 	{}	/* Terminator */
 };
@@ -222,6 +288,8 @@ static void __init overo_init(void)
 	omap_serial_init();
 	twl4030_mmc_init(mmc);
 	overo_flash_init();
+	usb_musb_init();
+	overo_ads7846_init();
 
 	if ((gpio_request(OVERO_GPIO_W2W_NRESET,
 			  "OVERO_GPIO_W2W_NRESET") == 0) &&
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
new file mode 100644
index 00000000000..a7381729645
--- /dev/null
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -0,0 +1,419 @@
+/*
+ * linux/arch/arm/mach-omap2/board-rx51-flash.c
+ *
+ * Copyright (C) 2008-2009 Nokia
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/input.h>
+#include <linux/spi/spi.h>
+#include <linux/i2c.h>
+#include <linux/i2c/twl4030.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/regulator/machine.h>
+#include <linux/gpio.h>
+
+#include <mach/mcspi.h>
+#include <mach/mux.h>
+#include <mach/board.h>
+#include <mach/common.h>
+#include <mach/dma.h>
+#include <mach/gpmc.h>
+#include <mach/keypad.h>
+
+#include "mmc-twl4030.h"
+
+
+#define SMC91X_CS			1
+#define SMC91X_GPIO_IRQ			54
+#define SMC91X_GPIO_RESET		164
+#define SMC91X_GPIO_PWRDWN		86
+
+static struct resource rx51_smc91x_resources[] = {
+	[0] = {
+		.flags		= IORESOURCE_MEM,
+	},
+	[1] = {
+		.flags		= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+	},
+};
+
+static struct platform_device rx51_smc91x_device = {
+	.name		= "smc91x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(rx51_smc91x_resources),
+	.resource	= rx51_smc91x_resources,
+};
+
+static int rx51_keymap[] = {
+	KEY(0, 0, KEY_Q),
+	KEY(0, 1, KEY_W),
+	KEY(0, 2, KEY_E),
+	KEY(0, 3, KEY_R),
+	KEY(0, 4, KEY_T),
+	KEY(0, 5, KEY_Y),
+	KEY(0, 6, KEY_U),
+	KEY(0, 7, KEY_I),
+	KEY(1, 0, KEY_O),
+	KEY(1, 1, KEY_D),
+	KEY(1, 2, KEY_DOT),
+	KEY(1, 3, KEY_V),
+	KEY(1, 4, KEY_DOWN),
+	KEY(2, 0, KEY_P),
+	KEY(2, 1, KEY_F),
+	KEY(2, 2, KEY_UP),
+	KEY(2, 3, KEY_B),
+	KEY(2, 4, KEY_RIGHT),
+	KEY(3, 0, KEY_COMMA),
+	KEY(3, 1, KEY_G),
+	KEY(3, 2, KEY_ENTER),
+	KEY(3, 3, KEY_N),
+	KEY(4, 0, KEY_BACKSPACE),
+	KEY(4, 1, KEY_H),
+	KEY(4, 3, KEY_M),
+	KEY(4, 4, KEY_LEFTCTRL),
+	KEY(5, 1, KEY_J),
+	KEY(5, 2, KEY_Z),
+	KEY(5, 3, KEY_SPACE),
+	KEY(5, 4, KEY_LEFTSHIFT),
+	KEY(6, 0, KEY_A),
+	KEY(6, 1, KEY_K),
+	KEY(6, 2, KEY_X),
+	KEY(6, 3, KEY_SPACE),
+	KEY(6, 4, KEY_FN),
+	KEY(7, 0, KEY_S),
+	KEY(7, 1, KEY_L),
+	KEY(7, 2, KEY_C),
+	KEY(7, 3, KEY_LEFT),
+	KEY(0xff, 0, KEY_F6),
+	KEY(0xff, 1, KEY_F7),
+	KEY(0xff, 2, KEY_F8),
+	KEY(0xff, 4, KEY_F9),
+	KEY(0xff, 5, KEY_F10),
+};
+
+static struct twl4030_keypad_data rx51_kp_data = {
+	.rows		= 8,
+	.cols		= 8,
+	.keymap		= rx51_keymap,
+	.keymapsize	= ARRAY_SIZE(rx51_keymap),
+	.rep		= 1,
+};
+
+static struct platform_device *rx51_peripherals_devices[] = {
+	&rx51_smc91x_device,
+};
+
+/*
+ * Timings are taken from smsc-lan91c96-ms.pdf
+ */
+static int smc91x_init_gpmc(int cs)
+{
+	struct gpmc_timings t;
+	const int t2_r = 45;		/* t2 in Figure 12.10 */
+	const int t2_w = 30;		/* t2 in Figure 12.11 */
+	const int t3 = 15;		/* t3 in Figure 12.10 */
+	const int t5_r = 0;		/* t5 in Figure 12.10 */
+	const int t6_r = 45;		/* t6 in Figure 12.10 */
+	const int t6_w = 0;		/* t6 in Figure 12.11 */
+	const int t7_w = 15;		/* t7 in Figure 12.11 */
+	const int t15 = 12;		/* t15 in Figure 12.2 */
+	const int t20 = 185;		/* t20 in Figure 12.2 */
+
+	memset(&t, 0, sizeof(t));
+
+	t.cs_on = t15;
+	t.cs_rd_off = t3 + t2_r + t5_r;	/* Figure 12.10 */
+	t.cs_wr_off = t3 + t2_w + t6_w;	/* Figure 12.11 */
+	t.adv_on = t3;			/* Figure 12.10 */
+	t.adv_rd_off = t3 + t2_r;	/* Figure 12.10 */
+	t.adv_wr_off = t3 + t2_w;	/* Figure 12.11 */
+	t.oe_off = t3 + t2_r + t5_r;	/* Figure 12.10 */
+	t.oe_on = t.oe_off - t6_r;	/* Figure 12.10 */
+	t.we_off = t3 + t2_w + t6_w;	/* Figure 12.11 */
+	t.we_on = t.we_off - t7_w;	/* Figure 12.11 */
+	t.rd_cycle = t20;		/* Figure 12.2 */
+	t.wr_cycle = t20;		/* Figure 12.4 */
+	t.access = t3 + t2_r + t5_r;	/* Figure 12.10 */
+	t.wr_access = t3 + t2_w + t6_w;	/* Figure 12.11 */
+
+	gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, GPMC_CONFIG1_DEVICESIZE_16);
+
+	return gpmc_cs_set_timings(cs, &t);
+}
+
+static void __init rx51_init_smc91x(void)
+{
+	unsigned long cs_mem_base;
+	int ret;
+
+	omap_cfg_reg(U8_34XX_GPIO54_DOWN);
+	omap_cfg_reg(G25_34XX_GPIO86_OUT);
+	omap_cfg_reg(H19_34XX_GPIO164_OUT);
+
+	if (gpmc_cs_request(SMC91X_CS, SZ_16M, &cs_mem_base) < 0) {
+		printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
+		return;
+	}
+
+	rx51_smc91x_resources[0].start = cs_mem_base + 0x300;
+	rx51_smc91x_resources[0].end = cs_mem_base + 0x30f;
+
+	smc91x_init_gpmc(SMC91X_CS);
+
+	if (gpio_request(SMC91X_GPIO_IRQ, "SMC91X irq") < 0)
+		goto free1;
+
+	gpio_direction_input(SMC91X_GPIO_IRQ);
+	rx51_smc91x_resources[1].start = gpio_to_irq(SMC91X_GPIO_IRQ);
+
+	ret = gpio_request(SMC91X_GPIO_PWRDWN, "SMC91X powerdown");
+	if (ret)
+		goto free2;
+	gpio_direction_output(SMC91X_GPIO_PWRDWN, 0);
+
+	ret = gpio_request(SMC91X_GPIO_RESET, "SMC91X reset");
+	if (ret)
+		goto free3;
+	gpio_direction_output(SMC91X_GPIO_RESET, 0);
+	gpio_set_value(SMC91X_GPIO_RESET, 1);
+	msleep(100);
+	gpio_set_value(SMC91X_GPIO_RESET, 0);
+
+	return;
+
+free3:
+	gpio_free(SMC91X_GPIO_PWRDWN);
+free2:
+	gpio_free(SMC91X_GPIO_IRQ);
+free1:
+	gpmc_cs_free(SMC91X_CS);
+
+	printk(KERN_ERR "Could not initialize smc91x\n");
+}
+
+static struct twl4030_madc_platform_data rx51_madc_data = {
+	.irq_line		= 1,
+};
+
+static struct twl4030_hsmmc_info mmc[] = {
+	{
+		.name		= "external",
+		.mmc		= 1,
+		.wires		= 4,
+		.cover_only	= true,
+		.gpio_cd	= 160,
+		.gpio_wp	= -EINVAL,
+	},
+	{
+		.name		= "internal",
+		.mmc		= 2,
+		.wires		= 8,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+	},
+	{}	/* Terminator */
+};
+
+static struct regulator_consumer_supply rx51_vmmc1_supply = {
+	.supply			= "vmmc",
+};
+
+static struct regulator_consumer_supply rx51_vmmc2_supply = {
+	.supply			= "vmmc",
+};
+
+static struct regulator_consumer_supply rx51_vsim_supply = {
+	.supply			= "vmmc_aux",
+};
+
+static struct regulator_init_data rx51_vaux1 = {
+	.constraints = {
+		.name			= "V28",
+		.min_uV			= 2800000,
+		.max_uV			= 2800000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data rx51_vaux2 = {
+	.constraints = {
+		.name			= "VCSI",
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+/* VAUX3 - adds more power to VIO_18 rail */
+static struct regulator_init_data rx51_vaux3 = {
+	.constraints = {
+		.name			= "VCAM_DIG_18",
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data rx51_vaux4 = {
+	.constraints = {
+		.name			= "VCAM_ANA_28",
+		.min_uV			= 2800000,
+		.max_uV			= 2800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static struct regulator_init_data rx51_vmmc1 = {
+	.constraints = {
+		.min_uV			= 1850000,
+		.max_uV			= 3150000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &rx51_vmmc1_supply,
+};
+
+static struct regulator_init_data rx51_vmmc2 = {
+	.constraints = {
+		.name			= "VMMC2_30",
+		.min_uV			= 1850000,
+		.max_uV			= 3150000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &rx51_vmmc2_supply,
+};
+
+static struct regulator_init_data rx51_vsim = {
+	.constraints = {
+		.name			= "VMMC2_IO_18",
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &rx51_vsim_supply,
+};
+
+static struct regulator_init_data rx51_vdac = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+};
+
+static int rx51_twlgpio_setup(struct device *dev, unsigned gpio, unsigned n)
+{
+	/* FIXME this gpio setup is just a placeholder for now */
+	gpio_request(gpio + 6, "backlight_pwm");
+	gpio_direction_output(gpio + 6, 0);
+	gpio_request(gpio + 7, "speaker_en");
+	gpio_direction_output(gpio + 7, 1);
+
+	/* set up MMC adapters, linking their regulators to them */
+	twl4030_mmc_init(mmc);
+	rx51_vmmc1_supply.dev = mmc[0].dev;
+	rx51_vmmc2_supply.dev = mmc[1].dev;
+	rx51_vsim_supply.dev = mmc[1].dev;
+
+	return 0;
+}
+
+static struct twl4030_gpio_platform_data rx51_gpio_data = {
+	.gpio_base		= OMAP_MAX_GPIO_LINES,
+	.irq_base		= TWL4030_GPIO_IRQ_BASE,
+	.irq_end		= TWL4030_GPIO_IRQ_END,
+	.pulldowns		= BIT(0) | BIT(1) | BIT(2) | BIT(3)
+				| BIT(4) | BIT(5)
+				| BIT(8) | BIT(9) | BIT(10) | BIT(11)
+				| BIT(12) | BIT(13) | BIT(14) | BIT(15)
+				| BIT(16) | BIT(17) ,
+	.setup			= rx51_twlgpio_setup,
+};
+
+static struct twl4030_platform_data rx51_twldata = {
+	.irq_base		= TWL4030_IRQ_BASE,
+	.irq_end		= TWL4030_IRQ_END,
+
+	/* platform_data for children goes here */
+	.gpio			= &rx51_gpio_data,
+	.keypad			= &rx51_kp_data,
+	.madc			= &rx51_madc_data,
+
+	.vaux1			= &rx51_vaux1,
+	.vaux2			= &rx51_vaux2,
+	.vaux3			= &rx51_vaux3,
+	.vaux4			= &rx51_vaux4,
+	.vmmc1			= &rx51_vmmc1,
+	.vmmc2			= &rx51_vmmc2,
+	.vsim			= &rx51_vsim,
+	.vdac			= &rx51_vdac,
+};
+
+static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_1[] = {
+	{
+		I2C_BOARD_INFO("twl5030", 0x48),
+		.flags = I2C_CLIENT_WAKE,
+		.irq = INT_34XX_SYS_NIRQ,
+		.platform_data = &rx51_twldata,
+	},
+};
+
+static int __init rx51_i2c_init(void)
+{
+	omap_register_i2c_bus(1, 2600, rx51_peripherals_i2c_board_info_1,
+			ARRAY_SIZE(rx51_peripherals_i2c_board_info_1));
+	omap_register_i2c_bus(2, 100, NULL, 0);
+	omap_register_i2c_bus(3, 400, NULL, 0);
+	return 0;
+}
+
+
+void __init rx51_peripherals_init(void)
+{
+	platform_add_devices(rx51_peripherals_devices,
+				ARRAY_SIZE(rx51_peripherals_devices));
+	rx51_i2c_init();
+	rx51_init_smc91x();
+}
+
diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c
new file mode 100644
index 00000000000..6a3c5e53d99
--- /dev/null
+++ b/arch/arm/mach-omap2/board-rx51.c
@@ -0,0 +1,96 @@
+/*
+ * linux/arch/arm/mach-omap2/board-rx51.c
+ *
+ * Copyright (C) 2007, 2008 Nokia
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/mcspi.h>
+#include <mach/mux.h>
+#include <mach/board.h>
+#include <mach/common.h>
+#include <mach/keypad.h>
+#include <mach/dma.h>
+#include <mach/gpmc.h>
+#include <mach/usb.h>
+
+static struct omap_uart_config rx51_uart_config = {
+	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
+static struct omap_lcd_config rx51_lcd_config = {
+	.ctrl_name	= "internal",
+};
+
+static struct omap_fbmem_config rx51_fbmem0_config = {
+	.size = 752 * 1024,
+};
+
+static struct omap_fbmem_config rx51_fbmem1_config = {
+	.size = 752 * 1024,
+};
+
+static struct omap_fbmem_config rx51_fbmem2_config = {
+	.size = 752 * 1024,
+};
+
+static struct omap_board_config_kernel rx51_config[] = {
+	{ OMAP_TAG_UART,	&rx51_uart_config },
+	{ OMAP_TAG_FBMEM,	&rx51_fbmem0_config },
+	{ OMAP_TAG_FBMEM,	&rx51_fbmem1_config },
+	{ OMAP_TAG_FBMEM,	&rx51_fbmem2_config },
+	{ OMAP_TAG_LCD,		&rx51_lcd_config },
+};
+
+static void __init rx51_init_irq(void)
+{
+	omap2_init_common_hw();
+	omap_init_irq();
+	omap_gpio_init();
+}
+
+extern void __init rx51_peripherals_init(void);
+
+static void __init rx51_init(void)
+{
+	omap_board_config = rx51_config;
+	omap_board_config_size = ARRAY_SIZE(rx51_config);
+	omap_serial_init();
+	usb_musb_init();
+	rx51_peripherals_init();
+}
+
+static void __init rx51_map_io(void)
+{
+	omap2_set_globals_343x();
+	omap2_map_common_io();
+}
+
+MACHINE_START(NOKIA_RX51, "Nokia RX-51 board")
+	/* Maintainer: Lauri Leukkunen <lauri.leukkunen@nokia.com> */
+	.phys_io	= 0x48000000,
+	.io_pg_offst	= ((0xd8000000) >> 18) & 0xfffc,
+	.boot_params	= 0x80000100,
+	.map_io		= rx51_map_io,
+	.init_irq	= rx51_init_irq,
+	.init_machine	= rx51_init,
+	.timer		= &omap_timer,
+MACHINE_END
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 8075f5868c3..d6b4b2f8722 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -28,13 +28,121 @@
 #include <mach/eac.h>
 #include <mach/mmc.h>
 
-#if defined(CONFIG_OMAP_DSP) || defined(CONFIG_OMAP_DSP_MODULE)
-#define OMAP2_MBOX_BASE		IO_ADDRESS(OMAP24XX_MAILBOX_BASE)
+#if defined(CONFIG_VIDEO_OMAP2) || defined(CONFIG_VIDEO_OMAP2_MODULE)
 
-static struct resource mbox_resources[] = {
+static struct resource cam_resources[] = {
 	{
-		.start		= OMAP2_MBOX_BASE,
-		.end		= OMAP2_MBOX_BASE + 0x11f,
+		.start		= OMAP24XX_CAMERA_BASE,
+		.end		= OMAP24XX_CAMERA_BASE + 0xfff,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= INT_24XX_CAM_IRQ,
+		.flags		= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device omap_cam_device = {
+	.name		= "omap24xxcam",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(cam_resources),
+	.resource	= cam_resources,
+};
+
+static inline void omap_init_camera(void)
+{
+	platform_device_register(&omap_cam_device);
+}
+
+#elif defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
+
+static struct resource omap3isp_resources[] = {
+	{
+		.start		= OMAP3430_ISP_BASE,
+		.end		= OMAP3430_ISP_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_CBUFF_BASE,
+		.end		= OMAP3430_ISP_CBUFF_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_CCP2_BASE,
+		.end		= OMAP3430_ISP_CCP2_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_CCDC_BASE,
+		.end		= OMAP3430_ISP_CCDC_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_HIST_BASE,
+		.end		= OMAP3430_ISP_HIST_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_H3A_BASE,
+		.end		= OMAP3430_ISP_H3A_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_PREV_BASE,
+		.end		= OMAP3430_ISP_PREV_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_RESZ_BASE,
+		.end		= OMAP3430_ISP_RESZ_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_SBL_BASE,
+		.end		= OMAP3430_ISP_SBL_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_CSI2A_BASE,
+		.end		= OMAP3430_ISP_CSI2A_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= OMAP3430_ISP_CSI2PHY_BASE,
+		.end		= OMAP3430_ISP_CSI2PHY_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= INT_34XX_CAM_IRQ,
+		.flags		= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device omap3isp_device = {
+	.name		= "omap3isp",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(omap3isp_resources),
+	.resource	= omap3isp_resources,
+};
+
+static inline void omap_init_camera(void)
+{
+	platform_device_register(&omap3isp_device);
+}
+#else
+static inline void omap_init_camera(void)
+{
+}
+#endif
+
+#if defined(CONFIG_OMAP_MBOX_FWK) || defined(CONFIG_OMAP_MBOX_FWK_MODULE)
+
+#define MBOX_REG_SIZE	0x120
+
+static struct resource omap2_mbox_resources[] = {
+	{
+		.start		= OMAP24XX_MAILBOX_BASE,
+		.end		= OMAP24XX_MAILBOX_BASE + MBOX_REG_SIZE - 1,
 		.flags		= IORESOURCE_MEM,
 	},
 	{
@@ -47,20 +155,40 @@ static struct resource mbox_resources[] = {
 	},
 };
 
+static struct resource omap3_mbox_resources[] = {
+	{
+		.start		= OMAP34XX_MAILBOX_BASE,
+		.end		= OMAP34XX_MAILBOX_BASE + MBOX_REG_SIZE - 1,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= INT_24XX_MAIL_U0_MPU,
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
 static struct platform_device mbox_device = {
-	.name		= "mailbox",
+	.name		= "omap2-mailbox",
 	.id		= -1,
-	.num_resources	= ARRAY_SIZE(mbox_resources),
-	.resource	= mbox_resources,
 };
 
 static inline void omap_init_mbox(void)
 {
+	if (cpu_is_omap2420()) {
+		mbox_device.num_resources = ARRAY_SIZE(omap2_mbox_resources);
+		mbox_device.resource = omap2_mbox_resources;
+	} else if (cpu_is_omap3430()) {
+		mbox_device.num_resources = ARRAY_SIZE(omap3_mbox_resources);
+		mbox_device.resource = omap3_mbox_resources;
+	} else {
+		pr_err("%s: platform not supported\n", __func__);
+		return;
+	}
 	platform_device_register(&mbox_device);
 }
 #else
 static inline void omap_init_mbox(void) { }
-#endif
+#endif /* CONFIG_OMAP_MBOX_FWK */
 
 #if defined(CONFIG_OMAP_STI)
 
@@ -507,6 +635,7 @@ static int __init omap2_init_devices(void)
 	 * in alphabetical order so they're easier to sort through.
 	 */
 	omap_hsmmc_reset();
+	omap_init_camera();
 	omap_init_mbox();
 	omap_init_mcspi();
 	omap_hdq_init();
diff --git a/arch/arm/mach-omap2/mailbox.c b/arch/arm/mach-omap2/mailbox.c
index 32b7af3c610..fd5b8a5925c 100644
--- a/arch/arm/mach-omap2/mailbox.c
+++ b/arch/arm/mach-omap2/mailbox.c
@@ -1,9 +1,9 @@
 /*
- * Mailbox reservation modules for OMAP2
+ * Mailbox reservation modules for OMAP2/3
  *
- * Copyright (C) 2006 Nokia Corporation
+ * Copyright (C) 2006-2009 Nokia Corporation
  * Written by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
- *        and  Paul Mundt <paul.mundt@nokia.com>
+ *        and  Paul Mundt
  *
  * This file is subject to the terms and conditions of the GNU General Public
  * License.  See the file "COPYING" in the main directory of this archive
@@ -18,40 +18,22 @@
 #include <mach/mailbox.h>
 #include <mach/irqs.h>
 
-#define MAILBOX_REVISION		0x00
-#define MAILBOX_SYSCONFIG		0x10
-#define MAILBOX_SYSSTATUS		0x14
-#define MAILBOX_MESSAGE_0		0x40
-#define MAILBOX_MESSAGE_1		0x44
-#define MAILBOX_MESSAGE_2		0x48
-#define MAILBOX_MESSAGE_3		0x4c
-#define MAILBOX_MESSAGE_4		0x50
-#define MAILBOX_MESSAGE_5		0x54
-#define MAILBOX_FIFOSTATUS_0		0x80
-#define MAILBOX_FIFOSTATUS_1		0x84
-#define MAILBOX_FIFOSTATUS_2		0x88
-#define MAILBOX_FIFOSTATUS_3		0x8c
-#define MAILBOX_FIFOSTATUS_4		0x90
-#define MAILBOX_FIFOSTATUS_5		0x94
-#define MAILBOX_MSGSTATUS_0		0xc0
-#define MAILBOX_MSGSTATUS_1		0xc4
-#define MAILBOX_MSGSTATUS_2		0xc8
-#define MAILBOX_MSGSTATUS_3		0xcc
-#define MAILBOX_MSGSTATUS_4		0xd0
-#define MAILBOX_MSGSTATUS_5		0xd4
-#define MAILBOX_IRQSTATUS_0		0x100
-#define MAILBOX_IRQENABLE_0		0x104
-#define MAILBOX_IRQSTATUS_1		0x108
-#define MAILBOX_IRQENABLE_1		0x10c
-#define MAILBOX_IRQSTATUS_2		0x110
-#define MAILBOX_IRQENABLE_2		0x114
-#define MAILBOX_IRQSTATUS_3		0x118
-#define MAILBOX_IRQENABLE_3		0x11c
-
-static unsigned long mbox_base;
-
-#define MAILBOX_IRQ_NOTFULL(n)		(1 << (2 * (n) + 1))
-#define MAILBOX_IRQ_NEWMSG(n)		(1 << (2 * (n)))
+#define MAILBOX_REVISION		0x000
+#define MAILBOX_SYSCONFIG		0x010
+#define MAILBOX_SYSSTATUS		0x014
+#define MAILBOX_MESSAGE(m)		(0x040 + 4 * (m))
+#define MAILBOX_FIFOSTATUS(m)		(0x080 + 4 * (m))
+#define MAILBOX_MSGSTATUS(m)		(0x0c0 + 4 * (m))
+#define MAILBOX_IRQSTATUS(u)		(0x100 + 8 * (u))
+#define MAILBOX_IRQENABLE(u)		(0x104 + 8 * (u))
+
+#define MAILBOX_IRQ_NEWMSG(u)		(1 << (2 * (u)))
+#define MAILBOX_IRQ_NOTFULL(u)		(1 << (2 * (u) + 1))
+
+#define MBOX_REG_SIZE			0x120
+#define MBOX_NR_REGS			(MBOX_REG_SIZE / sizeof(u32))
+
+static void __iomem *mbox_base;
 
 struct omap_mbox2_fifo {
 	unsigned long msg;
@@ -66,6 +48,7 @@ struct omap_mbox2_priv {
 	unsigned long irqstatus;
 	u32 newmsg_bit;
 	u32 notfull_bit;
+	u32 ctx[MBOX_NR_REGS];
 };
 
 static struct clk *mbox_ick_handle;
@@ -73,14 +56,14 @@ static struct clk *mbox_ick_handle;
 static void omap2_mbox_enable_irq(struct omap_mbox *mbox,
 				  omap_mbox_type_t irq);
 
-static inline unsigned int mbox_read_reg(unsigned int reg)
+static inline unsigned int mbox_read_reg(size_t ofs)
 {
-	return __raw_readl(mbox_base + reg);
+	return __raw_readl(mbox_base + ofs);
 }
 
-static inline void mbox_write_reg(unsigned int val, unsigned int reg)
+static inline void mbox_write_reg(u32 val, size_t ofs)
 {
-	__raw_writel(val, mbox_base + reg);
+	__raw_writel(val, mbox_base + ofs);
 }
 
 /* Mailbox H/W preparations */
@@ -95,6 +78,9 @@ static int omap2_mbox_startup(struct omap_mbox *mbox)
 	}
 	clk_enable(mbox_ick_handle);
 
+	l = mbox_read_reg(MAILBOX_REVISION);
+	pr_info("omap mailbox rev %d.%d\n", (l & 0xf0) >> 4, (l & 0x0f));
+
 	/* set smart-idle & autoidle */
 	l = mbox_read_reg(MAILBOX_SYSCONFIG);
 	l |= 0x00000011;
@@ -183,6 +169,32 @@ static int omap2_mbox_is_irq(struct omap_mbox *mbox,
 	return (enable & status & bit);
 }
 
+static void omap2_mbox_save_ctx(struct omap_mbox *mbox)
+{
+	int i;
+	struct omap_mbox2_priv *p = mbox->priv;
+
+	for (i = 0; i < MBOX_NR_REGS; i++) {
+		p->ctx[i] = mbox_read_reg(i * sizeof(u32));
+
+		dev_dbg(mbox->dev, "%s: [%02x] %08x\n", __func__,
+			i, p->ctx[i]);
+	}
+}
+
+static void omap2_mbox_restore_ctx(struct omap_mbox *mbox)
+{
+	int i;
+	struct omap_mbox2_priv *p = mbox->priv;
+
+	for (i = 0; i < MBOX_NR_REGS; i++) {
+		mbox_write_reg(p->ctx[i], i * sizeof(u32));
+
+		dev_dbg(mbox->dev, "%s: [%02x] %08x\n", __func__,
+			i, p->ctx[i]);
+	}
+}
+
 static struct omap_mbox_ops omap2_mbox_ops = {
 	.type		= OMAP_MBOX_TYPE2,
 	.startup	= omap2_mbox_startup,
@@ -195,6 +207,8 @@ static struct omap_mbox_ops omap2_mbox_ops = {
 	.disable_irq	= omap2_mbox_disable_irq,
 	.ack_irq	= omap2_mbox_ack_irq,
 	.is_irq		= omap2_mbox_is_irq,
+	.save_ctx	= omap2_mbox_save_ctx,
+	.restore_ctx	= omap2_mbox_restore_ctx,
 };
 
 /*
@@ -209,15 +223,15 @@ static struct omap_mbox_ops omap2_mbox_ops = {
 /* DSP */
 static struct omap_mbox2_priv omap2_mbox_dsp_priv = {
 	.tx_fifo = {
-		.msg		= MAILBOX_MESSAGE_0,
-		.fifo_stat	= MAILBOX_FIFOSTATUS_0,
+		.msg		= MAILBOX_MESSAGE(0),
+		.fifo_stat	= MAILBOX_FIFOSTATUS(0),
 	},
 	.rx_fifo = {
-		.msg		= MAILBOX_MESSAGE_1,
-		.msg_stat	= MAILBOX_MSGSTATUS_1,
+		.msg		= MAILBOX_MESSAGE(1),
+		.msg_stat	= MAILBOX_MSGSTATUS(1),
 	},
-	.irqenable	= MAILBOX_IRQENABLE_0,
-	.irqstatus	= MAILBOX_IRQSTATUS_0,
+	.irqenable	= MAILBOX_IRQENABLE(0),
+	.irqstatus	= MAILBOX_IRQSTATUS(0),
 	.notfull_bit	= MAILBOX_IRQ_NOTFULL(0),
 	.newmsg_bit	= MAILBOX_IRQ_NEWMSG(1),
 };
@@ -229,18 +243,18 @@ struct omap_mbox mbox_dsp_info = {
 };
 EXPORT_SYMBOL(mbox_dsp_info);
 
-/* IVA */
+#if defined(CONFIG_ARCH_OMAP2420) /* IVA */
 static struct omap_mbox2_priv omap2_mbox_iva_priv = {
 	.tx_fifo = {
-		.msg		= MAILBOX_MESSAGE_2,
-		.fifo_stat	= MAILBOX_FIFOSTATUS_2,
+		.msg		= MAILBOX_MESSAGE(2),
+		.fifo_stat	= MAILBOX_FIFOSTATUS(2),
 	},
 	.rx_fifo = {
-		.msg		= MAILBOX_MESSAGE_3,
-		.msg_stat	= MAILBOX_MSGSTATUS_3,
+		.msg		= MAILBOX_MESSAGE(3),
+		.msg_stat	= MAILBOX_MSGSTATUS(3),
 	},
-	.irqenable	= MAILBOX_IRQENABLE_3,
-	.irqstatus	= MAILBOX_IRQSTATUS_3,
+	.irqenable	= MAILBOX_IRQENABLE(3),
+	.irqstatus	= MAILBOX_IRQSTATUS(3),
 	.notfull_bit	= MAILBOX_IRQ_NOTFULL(2),
 	.newmsg_bit	= MAILBOX_IRQ_NEWMSG(3),
 };
@@ -250,17 +264,12 @@ static struct omap_mbox mbox_iva_info = {
 	.ops	= &omap2_mbox_ops,
 	.priv	= &omap2_mbox_iva_priv,
 };
+#endif
 
-static int __init omap2_mbox_probe(struct platform_device *pdev)
+static int __devinit omap2_mbox_probe(struct platform_device *pdev)
 {
 	struct resource *res;
-	int ret = 0;
-
-	if (pdev->num_resources != 3) {
-		dev_err(&pdev->dev, "invalid number of resources: %d\n",
-			pdev->num_resources);
-		return -ENODEV;
-	}
+	int ret;
 
 	/* MBOX base */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -268,42 +277,61 @@ static int __init omap2_mbox_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "invalid mem resource\n");
 		return -ENODEV;
 	}
-	mbox_base = res->start;
+	mbox_base = ioremap(res->start, res->end - res->start);
+	if (!mbox_base)
+		return -ENOMEM;
 
-	/* DSP IRQ */
-	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-	if (unlikely(!res)) {
+	/* DSP or IVA2 IRQ */
+	mbox_dsp_info.irq = platform_get_irq(pdev, 0);
+	if (mbox_dsp_info.irq < 0) {
 		dev_err(&pdev->dev, "invalid irq resource\n");
-		return -ENODEV;
+		ret = -ENODEV;
+		goto err_dsp;
 	}
-	mbox_dsp_info.irq = res->start;
 
-	ret = omap_mbox_register(&mbox_dsp_info);
-
-	/* IVA IRQ */
-	res = platform_get_resource(pdev, IORESOURCE_IRQ, 1);
-	if (unlikely(!res)) {
-		dev_err(&pdev->dev, "invalid irq resource\n");
-		return -ENODEV;
+	ret = omap_mbox_register(&pdev->dev, &mbox_dsp_info);
+	if (ret)
+		goto err_dsp;
+
+#if defined(CONFIG_ARCH_OMAP2420) /* IVA */
+	if (cpu_is_omap2420()) {
+		/* IVA IRQ */
+		res = platform_get_resource(pdev, IORESOURCE_IRQ, 1);
+		if (unlikely(!res)) {
+			dev_err(&pdev->dev, "invalid irq resource\n");
+			ret = -ENODEV;
+			goto err_iva1;
+		}
+		mbox_iva_info.irq = res->start;
+		ret = omap_mbox_register(&pdev->dev, &mbox_iva_info);
+		if (ret)
+			goto err_iva1;
 	}
-	mbox_iva_info.irq = res->start;
-
-	ret = omap_mbox_register(&mbox_iva_info);
+#endif
+	return 0;
 
+err_iva1:
+	omap_mbox_unregister(&mbox_dsp_info);
+err_dsp:
+	iounmap(mbox_base);
 	return ret;
 }
 
-static int omap2_mbox_remove(struct platform_device *pdev)
+static int __devexit omap2_mbox_remove(struct platform_device *pdev)
 {
+#if defined(CONFIG_ARCH_OMAP2420)
+	omap_mbox_unregister(&mbox_iva_info);
+#endif
 	omap_mbox_unregister(&mbox_dsp_info);
+	iounmap(mbox_base);
 	return 0;
 }
 
 static struct platform_driver omap2_mbox_driver = {
 	.probe = omap2_mbox_probe,
-	.remove = omap2_mbox_remove,
+	.remove = __devexit_p(omap2_mbox_remove),
 	.driver = {
-		.name = "mailbox",
+		.name = "omap2-mailbox",
 	},
 };
 
@@ -320,4 +348,7 @@ static void __exit omap2_mbox_exit(void)
 module_init(omap2_mbox_init);
 module_exit(omap2_mbox_exit);
 
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("omap mailbox: omap2/3 architecture specific functions");
+MODULE_AUTHOR("Hiroshi DOYU <Hiroshi.DOYU@nokia.com>, Paul Mundt");
+MODULE_ALIAS("platform:omap2-mailbox");
diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c
index 437f52073f6..dc40b3e7220 100644
--- a/arch/arm/mach-omap2/mmc-twl4030.c
+++ b/arch/arm/mach-omap2/mmc-twl4030.c
@@ -17,6 +17,7 @@
 #include <linux/delay.h>
 #include <linux/gpio.h>
 #include <linux/i2c/twl4030.h>
+#include <linux/regulator/machine.h>
 
 #include <mach/hardware.h>
 #include <mach/control.h>
@@ -44,6 +45,7 @@
 #define VMMC2_315V		0x0c
 #define VMMC2_300V		0x0b
 #define VMMC2_285V		0x0a
+#define VMMC2_280V		0x09
 #define VMMC2_260V		0x08
 #define VMMC2_185V		0x06
 #define VMMC2_DEDICATED		0x2E
@@ -59,8 +61,8 @@ static struct twl_mmc_controller {
 	struct omap_mmc_platform_data	*mmc;
 	u8		twl_vmmc_dev_grp;
 	u8		twl_mmc_dedicated;
-	char		name[HSMMC_NAME_LEN];
-} hsmmc[] = {
+	char		name[HSMMC_NAME_LEN + 1];
+} hsmmc[OMAP34XX_NR_MMC] = {
 	{
 		.twl_vmmc_dev_grp		= VMMC1_DEV_GRP,
 		.twl_mmc_dedicated		= VMMC1_DEDICATED,
@@ -98,6 +100,14 @@ static int twl_mmc_get_ro(struct device *dev, int slot)
 	return gpio_get_value_cansleep(mmc->slots[0].gpio_wp);
 }
 
+static int twl_mmc_get_cover_state(struct device *dev, int slot)
+{
+	struct omap_mmc_platform_data *mmc = dev->platform_data;
+
+	/* NOTE: assumes card detect signal is active-low */
+	return !gpio_get_value_cansleep(mmc->slots[0].switch_pin);
+}
+
 /*
  * MMC Slot Initialization.
  */
@@ -166,66 +176,85 @@ static int twl_mmc_resume(struct device *dev, int slot)
 /*
  * Sets the MMC voltage in twl4030
  */
+
+#define MMC1_OCR	(MMC_VDD_165_195 \
+		|MMC_VDD_28_29|MMC_VDD_29_30|MMC_VDD_30_31|MMC_VDD_31_32)
+#define MMC2_OCR	(MMC_VDD_165_195 \
+		|MMC_VDD_25_26|MMC_VDD_26_27|MMC_VDD_27_28 \
+		|MMC_VDD_28_29|MMC_VDD_29_30|MMC_VDD_30_31|MMC_VDD_31_32)
+
 static int twl_mmc_set_voltage(struct twl_mmc_controller *c, int vdd)
 {
 	int ret;
-	u8 vmmc, dev_grp_val;
-
-	switch (1 << vdd) {
-	case MMC_VDD_35_36:
-	case MMC_VDD_34_35:
-	case MMC_VDD_33_34:
-	case MMC_VDD_32_33:
-	case MMC_VDD_31_32:
-	case MMC_VDD_30_31:
-		if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP)
-			vmmc = VMMC1_315V;
-		else
-			vmmc = VMMC2_315V;
-		break;
-	case MMC_VDD_29_30:
-		if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP)
-			vmmc = VMMC1_315V;
-		else
-			vmmc = VMMC2_300V;
-		break;
-	case MMC_VDD_27_28:
-	case MMC_VDD_26_27:
-		if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP)
-			vmmc = VMMC1_285V;
-		else
-			vmmc = VMMC2_285V;
-		break;
-	case MMC_VDD_25_26:
-	case MMC_VDD_24_25:
-	case MMC_VDD_23_24:
-	case MMC_VDD_22_23:
-	case MMC_VDD_21_22:
-	case MMC_VDD_20_21:
-		if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP)
-			vmmc = VMMC1_285V;
-		else
-			vmmc = VMMC2_260V;
-		break;
-	case MMC_VDD_165_195:
-		if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP)
+	u8 vmmc = 0, dev_grp_val;
+
+	if (!vdd)
+		goto doit;
+
+	if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP) {
+		/* VMMC1:  max 220 mA.  And for 8-bit mode,
+		 * VSIM:  max 50 mA
+		 */
+		switch (1 << vdd) {
+		case MMC_VDD_165_195:
 			vmmc = VMMC1_185V;
-		else
+			/* and VSIM_180V */
+			break;
+		case MMC_VDD_28_29:
+			vmmc = VMMC1_285V;
+			/* and VSIM_280V */
+			break;
+		case MMC_VDD_29_30:
+		case MMC_VDD_30_31:
+			vmmc = VMMC1_300V;
+			/* and VSIM_300V */
+			break;
+		case MMC_VDD_31_32:
+			vmmc = VMMC1_315V;
+			/* error if VSIM needed */
+			break;
+		default:
+			return -EINVAL;
+		}
+	} else if (c->twl_vmmc_dev_grp == VMMC2_DEV_GRP) {
+		/* VMMC2:  max 100 mA */
+		switch (1 << vdd) {
+		case MMC_VDD_165_195:
 			vmmc = VMMC2_185V;
-		break;
-	default:
-		vmmc = 0;
-		break;
+			break;
+		case MMC_VDD_25_26:
+		case MMC_VDD_26_27:
+			vmmc = VMMC2_260V;
+			break;
+		case MMC_VDD_27_28:
+			vmmc = VMMC2_280V;
+			break;
+		case MMC_VDD_28_29:
+			vmmc = VMMC2_285V;
+			break;
+		case MMC_VDD_29_30:
+		case MMC_VDD_30_31:
+			vmmc = VMMC2_300V;
+			break;
+		case MMC_VDD_31_32:
+			vmmc = VMMC2_315V;
+			break;
+		default:
+			return -EINVAL;
+		}
+	} else {
+		return -EINVAL;
 	}
 
-	if (vmmc)
+doit:
+	if (vdd)
 		dev_grp_val = VMMC_DEV_GRP_P1;	/* Power up */
 	else
 		dev_grp_val = LDO_CLR;		/* Power down */
 
 	ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
 					dev_grp_val, c->twl_vmmc_dev_grp);
-	if (ret)
+	if (ret || !vdd)
 		return ret;
 
 	ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
@@ -242,6 +271,14 @@ static int twl_mmc1_set_power(struct device *dev, int slot, int power_on,
 	struct twl_mmc_controller *c = &hsmmc[0];
 	struct omap_mmc_platform_data *mmc = dev->platform_data;
 
+	/*
+	 * Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the
+	 * card using the same TWL VMMC1 supply (hsmmc[0]); OMAP has both
+	 * 1.8V and 3.0V modes, controlled by the PBIAS register.
+	 *
+	 * In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which
+	 * is most naturally TWL VSIM; those pins also use PBIAS.
+	 */
 	if (power_on) {
 		if (cpu_is_omap2430()) {
 			reg = omap_ctrl_readl(OMAP243X_CONTROL_DEVCONF1);
@@ -298,6 +335,12 @@ static int twl_mmc2_set_power(struct device *dev, int slot, int power_on, int vd
 	struct twl_mmc_controller *c = &hsmmc[1];
 	struct omap_mmc_platform_data *mmc = dev->platform_data;
 
+	/*
+	 * Assume TWL VMMC2 (hsmmc[1]) is used only to power the card ... OMAP
+	 * VDDS is used to power the pins, optionally with a transceiver to
+	 * support cards using voltages other than VDDS (1.8V nominal).  When a
+	 * transceiver is used, DAT3..7 are muxed as transceiver control pins.
+	 */
 	if (power_on) {
 		if (mmc->slots[0].internal_clock) {
 			u32 reg;
@@ -314,6 +357,16 @@ static int twl_mmc2_set_power(struct device *dev, int slot, int power_on, int vd
 	return ret;
 }
 
+static int twl_mmc3_set_power(struct device *dev, int slot, int power_on,
+		int vdd)
+{
+	/*
+	 * Assume MMC3 has self-powered device connected, for example on-board
+	 * chip with external power source.
+	 */
+	return 0;
+}
+
 static struct omap_mmc_platform_data *hsmmc_data[OMAP34XX_NR_MMC] __initdata;
 
 void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers)
@@ -349,13 +402,13 @@ void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers)
 			return;
 		}
 
-		sprintf(twl->name, "mmc%islot%i", c->mmc, 1);
+		if (c->name)
+			strncpy(twl->name, c->name, HSMMC_NAME_LEN);
+		else
+			snprintf(twl->name, ARRAY_SIZE(twl->name),
+				"mmc%islot%i", c->mmc, 1);
 		mmc->slots[0].name = twl->name;
 		mmc->nr_slots = 1;
-		mmc->slots[0].ocr_mask = MMC_VDD_165_195 |
-					MMC_VDD_26_27 | MMC_VDD_27_28 |
-					MMC_VDD_29_30 |
-					MMC_VDD_30_31 | MMC_VDD_31_32;
 		mmc->slots[0].wires = c->wires;
 		mmc->slots[0].internal_clock = !c->ext_clock;
 		mmc->dma_mask = 0xffffffff;
@@ -369,7 +422,10 @@ void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers)
 
 			mmc->slots[0].switch_pin = c->gpio_cd;
 			mmc->slots[0].card_detect_irq = gpio_to_irq(c->gpio_cd);
-			mmc->slots[0].card_detect = twl_mmc_card_detect;
+			if (c->cover_only)
+				mmc->slots[0].get_cover_state = twl_mmc_get_cover_state;
+			else
+				mmc->slots[0].card_detect = twl_mmc_card_detect;
 		} else
 			mmc->slots[0].switch_pin = -EINVAL;
 
@@ -385,24 +441,43 @@ void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers)
 
 		/* NOTE:  we assume OMAP's MMC1 and MMC2 use
 		 * the TWL4030's VMMC1 and VMMC2, respectively;
-		 * and that OMAP's MMC3 isn't used.
+		 * and that MMC3 device has it's own power source.
 		 */
 
 		switch (c->mmc) {
 		case 1:
 			mmc->slots[0].set_power = twl_mmc1_set_power;
+			mmc->slots[0].ocr_mask = MMC1_OCR;
 			break;
 		case 2:
 			mmc->slots[0].set_power = twl_mmc2_set_power;
+			if (c->transceiver)
+				mmc->slots[0].ocr_mask = MMC2_OCR;
+			else
+				mmc->slots[0].ocr_mask = MMC_VDD_165_195;
+			break;
+		case 3:
+			mmc->slots[0].set_power = twl_mmc3_set_power;
+			mmc->slots[0].ocr_mask = MMC_VDD_165_195;
 			break;
 		default:
 			pr_err("MMC%d configuration not supported!\n", c->mmc);
+			kfree(mmc);
 			continue;
 		}
 		hsmmc_data[c->mmc - 1] = mmc;
 	}
 
 	omap2_init_mmc(hsmmc_data, OMAP34XX_NR_MMC);
+
+	/* pass the device nodes back to board setup code */
+	for (c = controllers; c->mmc; c++) {
+		struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1];
+
+		if (!c->mmc || c->mmc > nr_hsmmc)
+			continue;
+		c->dev = mmc->dev;
+	}
 }
 
 #endif
diff --git a/arch/arm/mach-omap2/mmc-twl4030.h b/arch/arm/mach-omap2/mmc-twl4030.h
index e1c8076400c..ea59e862429 100644
--- a/arch/arm/mach-omap2/mmc-twl4030.h
+++ b/arch/arm/mach-omap2/mmc-twl4030.h
@@ -9,9 +9,13 @@
 struct twl4030_hsmmc_info {
 	u8	mmc;		/* controller 1/2/3 */
 	u8	wires;		/* 1/4/8 wires */
+	bool	transceiver;	/* MMC-2 option */
+	bool	ext_clock;	/* use external pin for input clock */
+	bool	cover_only;	/* No card detect - just cover switch */
 	int	gpio_cd;	/* or -EINVAL */
 	int	gpio_wp;	/* or -EINVAL */
-	int	ext_clock:1;	/* use external pin for input clock */
+	char	*name;		/* or NULL for default */
+	struct device *dev;	/* returned: pointer to mmc adapter */
 };
 
 #if	defined(CONFIG_TWL4030_CORE) && \
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index dacb41f130c..026c4fc883a 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -453,10 +453,37 @@ MUX_CFG_34XX("AC1_3430_USB3FS_PHY_MM3_TXEN_N", 0x18a,
 
 
 /* 34XX GPIO - bidirectional, unless the name has an "_OUT" suffix.
+ * (Always specify PIN_INPUT, except for names suffixed by "_OUT".)
  * No internal pullup/pulldown without "_UP" or "_DOWN" suffix.
  */
+MUX_CFG_34XX("AF26_34XX_GPIO0", 0x1e0,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("AF22_34XX_GPIO9", 0xa18,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
 MUX_CFG_34XX("AH8_34XX_GPIO29", 0x5fa,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("U8_34XX_GPIO54_OUT", 0x0b4,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("U8_34XX_GPIO54_DOWN", 0x0b4,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLDOWN)
+MUX_CFG_34XX("L8_34XX_GPIO63", 0x0ce,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("G25_34XX_GPIO86_OUT", 0x0fc,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("AG4_34XX_GPIO134_OUT", 0x160,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("AE4_34XX_GPIO136_OUT", 0x164,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("AF6_34XX_GPIO140_UP", 0x16c,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AE6_34XX_GPIO141", 0x16e,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("AF5_34XX_GPIO142", 0x170,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("AE5_34XX_GPIO143", 0x172,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("H19_34XX_GPIO164_OUT", 0x19c,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
 MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
 };
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
new file mode 100644
index 00000000000..fc74e913c41
--- /dev/null
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -0,0 +1,187 @@
+/*
+ * linux/arch/arm/mach-omap2/usb-musb.c
+ *
+ * This file will contain the board specific details for the
+ * MENTOR USB OTG controller on OMAP3430
+ *
+ * Copyright (C) 2007-2008 Texas Instruments
+ * Copyright (C) 2008 Nokia Corporation
+ * Author: Vikram Pandita
+ *
+ * Generalization by:
+ * Felipe Balbi <felipe.balbi@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+
+#include <linux/usb/musb.h>
+
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/pm.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+
+static struct resource musb_resources[] = {
+	[0] = { /* start and end set dynamically */
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {	/* general IRQ */
+		.start	= INT_243X_HS_USB_MC,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {	/* DMA IRQ */
+		.start	= INT_243X_HS_USB_DMA,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static int clk_on;
+
+static int musb_set_clock(struct clk *clk, int state)
+{
+	if (state) {
+		if (clk_on > 0)
+			return -ENODEV;
+
+		clk_enable(clk);
+		clk_on = 1;
+	} else {
+		if (clk_on == 0)
+			return -ENODEV;
+
+		clk_disable(clk);
+		clk_on = 0;
+	}
+
+	return 0;
+}
+
+static struct musb_hdrc_eps_bits musb_eps[] = {
+	{	"ep1_tx", 10,	},
+	{	"ep1_rx", 10,	},
+	{	"ep2_tx", 9,	},
+	{	"ep2_rx", 9,	},
+	{	"ep3_tx", 3,	},
+	{	"ep3_rx", 3,	},
+	{	"ep4_tx", 3,	},
+	{	"ep4_rx", 3,	},
+	{	"ep5_tx", 3,	},
+	{	"ep5_rx", 3,	},
+	{	"ep6_tx", 3,	},
+	{	"ep6_rx", 3,	},
+	{	"ep7_tx", 3,	},
+	{	"ep7_rx", 3,	},
+	{	"ep8_tx", 2,	},
+	{	"ep8_rx", 2,	},
+	{	"ep9_tx", 2,	},
+	{	"ep9_rx", 2,	},
+	{	"ep10_tx", 2,	},
+	{	"ep10_rx", 2,	},
+	{	"ep11_tx", 2,	},
+	{	"ep11_rx", 2,	},
+	{	"ep12_tx", 2,	},
+	{	"ep12_rx", 2,	},
+	{	"ep13_tx", 2,	},
+	{	"ep13_rx", 2,	},
+	{	"ep14_tx", 2,	},
+	{	"ep14_rx", 2,	},
+	{	"ep15_tx", 2,	},
+	{	"ep15_rx", 2,	},
+};
+
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 1,
+	.dyn_fifo	= 1,
+	.soft_con	= 1,
+	.dma		= 1,
+	.num_eps	= 16,
+	.dma_channels	= 7,
+	.dma_req_chan	= (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3),
+	.ram_bits	= 12,
+	.eps_bits	= musb_eps,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#ifdef CONFIG_USB_MUSB_OTG
+	.mode		= MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+	.mode		= MUSB_HOST,
+#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
+	.mode		= MUSB_PERIPHERAL,
+#endif
+	/* .clock is set dynamically */
+	.set_clock	= musb_set_clock,
+	.config		= &musb_config,
+
+	/* REVISIT charge pump on TWL4030 can supply up to
+	 * 100 mA ... but this value is board-specific, like
+	 * "mode", and should be passed to usb_musb_init().
+	 */
+	.power		= 50,			/* up to 100 mA */
+};
+
+static u64 musb_dmamask = DMA_32BIT_MASK;
+
+static struct platform_device musb_device = {
+	.name		= "musb_hdrc",
+	.id		= -1,
+	.dev = {
+		.dma_mask		= &musb_dmamask,
+		.coherent_dma_mask	= DMA_32BIT_MASK,
+		.platform_data		= &musb_plat,
+	},
+	.num_resources	= ARRAY_SIZE(musb_resources),
+	.resource	= musb_resources,
+};
+
+#ifdef CONFIG_NOP_USB_XCEIV
+static u64 nop_xceiv_dmamask = DMA_32BIT_MASK;
+
+static struct platform_device nop_xceiv_device = {
+	.name		= "nop_usb_xceiv",
+	.id		= -1,
+	.dev = {
+		.dma_mask		= &nop_xceiv_dmamask,
+		.coherent_dma_mask	= DMA_32BIT_MASK,
+		.platform_data		= NULL,
+	},
+};
+#endif
+
+void __init usb_musb_init(void)
+{
+	if (cpu_is_omap243x())
+		musb_resources[0].start = OMAP243X_HS_BASE;
+	else
+		musb_resources[0].start = OMAP34XX_HSUSB_OTG_BASE;
+	musb_resources[0].end = musb_resources[0].start + SZ_8K - 1;
+
+	/*
+	 * REVISIT: This line can be removed once all the platforms using
+	 * musb_core.c have been converted to use use clkdev.
+	 */
+	musb_plat.clock = "ick";
+
+#ifdef CONFIG_NOP_USB_XCEIV
+	if (platform_device_register(&nop_xceiv_device) < 0) {
+		printk(KERN_ERR "Unable to register NOP-XCEIV device\n");
+		return;
+	}
+#endif
+
+	if (platform_device_register(&musb_device) < 0) {
+		printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n");
+		return;
+	}
+}