[PATCH] CRIS update: new subarchitecture v32

New CRIS sub architecture named v32.

From: Dave Jones <davej@redhat.com>

	Fix swapped kmalloc args

Signed-off-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

1 files changed, 296 insertions, 0 deletions

diff --git a/arch/cris/arch-v32/Kconfig b/arch/cris/arch-v32/Kconfig
new file mode 100644
index 00000000000..22f0ddc04c5
--- /dev/null
+++ b/arch/cris/arch-v32/Kconfig
@@ -0,0 +1,296 @@
+config ETRAX_DRAM_VIRTUAL_BASE
+	hex
+	depends on ETRAX_ARCH_V32
+	default "c0000000"
+
+config ETRAX_LED1G
+	string "First green LED bit"
+	depends on ETRAX_ARCH_V32
+	default "PA3"
+	help
+	  Bit to use for the first green LED (network LED).
+	  Most Axis products use bit A3 here.
+
+config ETRAX_LED1R
+	string "First red LED bit"
+	depends on ETRAX_ARCH_V32
+	default "PA4"
+	help
+	  Bit to use for the first red LED (network LED).
+	  Most Axis products use bit A4 here.
+
+config ETRAX_LED2G
+	string "Second green LED bit"
+	depends on ETRAX_ARCH_V32
+	default "PA5"
+	help
+	  Bit to use for the first green LED (status LED).
+	  Most Axis products use bit A5 here.
+
+config ETRAX_LED2R
+	string "Second red LED bit"
+	depends on ETRAX_ARCH_V32
+	default "PA6"
+	help
+	  Bit to use for the first red LED (network LED).
+	  Most Axis products use bit A6 here.
+
+config ETRAX_LED3G
+	string "Third green LED bit"
+	depends on ETRAX_ARCH_V32
+	default "PA7"
+	help
+	  Bit to use for the first green LED (drive/power LED).
+	  Most Axis products use bit A7 here.
+
+config ETRAX_LED3R
+	string "Third red LED bit"
+	depends on ETRAX_ARCH_V32
+	default "PA7"
+	help
+	  Bit to use for the first red LED (drive/power LED).
+	  Most Axis products use bit A7 here.
+
+choice
+	prompt "Product debug-port"
+	depends on ETRAX_ARCH_V32
+	default ETRAX_DEBUG_PORT0
+
+config ETRAX_DEBUG_PORT0
+	bool "Serial-0"
+	help
+	  Choose a serial port for the ETRAX debug console.  Default to
+	  port 0.
+
+config ETRAX_DEBUG_PORT1
+	bool "Serial-1"
+	help
+	  Use serial port 1 for the console.
+
+config ETRAX_DEBUG_PORT2
+	bool "Serial-2"
+	help
+	  Use serial port 2 for the console.
+
+config ETRAX_DEBUG_PORT3
+	bool "Serial-3"
+	help
+	  Use serial port 3 for the console.
+
+config ETRAX_DEBUG_PORT_NULL
+	bool "disabled"
+	help
+	  Disable serial-port debugging.
+
+endchoice
+
+choice
+	prompt "Kernel GDB port"
+	depends on ETRAX_KGDB
+	default ETRAX_KGDB_PORT0
+	help
+	  Choose a serial port for kernel debugging.  NOTE: This port should
+	  not be enabled under Drivers for built-in interfaces (as it has its
+	  own initialization code) and should not be the same as the debug port.
+
+config ETRAX_KGDB_PORT0
+	bool "Serial-0"
+	help
+	  Use serial port 0 for kernel debugging.
+
+config ETRAX_KGDB_PORT1
+	bool "Serial-1"
+	help
+	  Use serial port 1 for kernel debugging.
+
+config ETRAX_KGDB_PORT2
+	bool "Serial-2"
+	help
+	  Use serial port 2 for kernel debugging.
+
+config ETRAX_KGDB_PORT3
+	bool "Serial-3"
+	help
+	  Use serial port 3 for kernel debugging.
+
+endchoice
+
+config ETRAX_MEM_GRP1_CONFIG
+	hex "MEM_GRP1_CONFIG"
+	depends on ETRAX_ARCH_V32
+	default "4044a"
+	help
+	  Waitstates for flash. The default value is suitable for the
+	  standard flashes used in axis products (120 ns).
+
+config ETRAX_MEM_GRP2_CONFIG
+	hex "MEM_GRP2_CONFIG"
+	depends on ETRAX_ARCH_V32
+	default "0"
+	help
+	  Waitstates for SRAM. 0 is a good choice for most Axis products.
+
+config ETRAX_MEM_GRP3_CONFIG
+	hex "MEM_GRP3_CONFIG"
+	depends on ETRAX_ARCH_V32
+	default "0"
+	help
+	  Waitstates for CSP0-3. 0 is a good choice for most Axis products.
+	  It may need to be changed if external devices such as extra
+	  register-mapped LEDs are used.
+
+config ETRAX_MEM_GRP4_CONFIG
+	hex "MEM_GRP4_CONFIG"
+	depends on ETRAX_ARCH_V32
+	default "0"
+	help
+	  Waitstates for CSP4-6. 0 is a good choice for most Axis products.
+
+config ETRAX_SDRAM_GRP0_CONFIG
+	hex "SDRAM_GRP0_CONFIG"
+	depends on ETRAX_ARCH_V32
+	default "336"
+	help
+	  SDRAM configuration for group 0. The value depends on the
+	  hardware configuration. The default value is suitable
+	  for 32 MB organized as two 16 bits chips (e.g. Axis
+	  part number 18550) connected as one 32 bit device (i.e. in
+	  the same group).
+
+config ETRAX_SDRAM_GRP1_CONFIG
+	hex "SDRAM_GRP1_CONFIG"
+	depends on ETRAX_ARCH_V32
+	default "0"
+	help
+	  SDRAM configuration for group 1. The defult value is 0
+	  because group 1 is not used in the default configuration,
+	  described in the help for SDRAM_GRP0_CONFIG.
+
+config ETRAX_SDRAM_TIMING
+	hex "SDRAM_TIMING"
+	depends on ETRAX_ARCH_V32
+	default "104a"
+	help
+	  SDRAM timing parameters. The default value is ok for
+	  most hardwares but large SDRAMs may require a faster
+	  refresh (a.k.a 8K refresh). The default value implies
+	  100MHz clock and SDR mode.
+
+config ETRAX_SDRAM_COMMAND
+	hex "SDRAM_COMMAND"
+	depends on ETRAX_ARCH_V32
+	default "0"
+	help
+	  SDRAM command. Should be 0 unless you really know what
+	  you are doing (may be != 0 for unusual address line
+	  mappings such as in a MCM)..
+
+config ETRAX_DEF_GIO_PA_OE
+	hex "GIO_PA_OE"
+	depends on ETRAX_ARCH_V32
+	default "1c"
+	help
+	  Configures the direction of general port A bits.  1 is out, 0 is in.
+	  This is often totally different depending on the product used.
+	  There are some guidelines though - if you know that only LED's are
+	  connected to port PA, then they are usually connected to bits 2-4
+	  and you can therefore use 1c.  On other boards which don't have the
+	  LED's at the general ports, these bits are used for all kinds of
+	  stuff.  If you don't know what to use, it is always safe to put all
+	  as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PA_OUT
+	hex "GIO_PA_OUT"
+	depends on ETRAX_ARCH_V32
+	default "00"
+	help
+	  Configures the initial data for the general port A bits.  Most
+	  products should use 00 here.
+
+config ETRAX_DEF_GIO_PB_OE
+	hex "GIO_PB_OE"
+	depends on ETRAX_ARCH_V32
+	default "00000"
+	help
+	  Configures the direction of general port B bits.  1 is out, 0 is in.
+	  This is often totally different depending on the product used.
+	  There are some guidelines though - if you know that only LED's are
+	  connected to port PA, then they are usually connected to bits 2-4
+	  and you can therefore use 1c.  On other boards which don't have the
+	  LED's at the general ports, these bits are used for all kinds of
+	  stuff.  If you don't know what to use, it is always safe to put all
+	  as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PB_OUT
+	hex "GIO_PB_OUT"
+	depends on ETRAX_ARCH_V32
+	default "00000"
+	help
+	  Configures the initial data for the general port B bits.  Most
+	  products should use 00000 here.
+
+config ETRAX_DEF_GIO_PC_OE
+	hex "GIO_PC_OE"
+	depends on ETRAX_ARCH_V32
+	default "00000"
+	help
+	  Configures the direction of general port C bits.  1 is out, 0 is in.
+	  This is often totally different depending on the product used.
+	  There are some guidelines though - if you know that only LED's are
+	  connected to port PA, then they are usually connected to bits 2-4
+	  and you can therefore use 1c.  On other boards which don't have the
+	  LED's at the general ports, these bits are used for all kinds of
+	  stuff.  If you don't know what to use, it is always safe to put all
+	  as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PC_OUT
+	hex "GIO_PC_OUT"
+	depends on ETRAX_ARCH_V32
+	default "00000"
+	help
+	  Configures the initial data for the general port C bits.  Most
+	  products should use 00000 here.
+
+config ETRAX_DEF_GIO_PD_OE
+	hex "GIO_PD_OE"
+	depends on ETRAX_ARCH_V32
+	default "00000"
+	help
+	  Configures the direction of general port D bits.  1 is out, 0 is in.
+	  This is often totally different depending on the product used.
+	  There are some guidelines though - if you know that only LED's are
+	  connected to port PA, then they are usually connected to bits 2-4
+	  and you can therefore use 1c.  On other boards which don't have the
+	  LED's at the general ports, these bits are used for all kinds of
+	  stuff.  If you don't know what to use, it is always safe to put all
+	  as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PD_OUT
+	hex "GIO_PD_OUT"
+	depends on ETRAX_ARCH_V32
+	default "00000"
+	help
+	  Configures the initial data for the general port D bits.  Most
+	  products should use 00000 here.
+
+config ETRAX_DEF_GIO_PE_OE
+	hex "GIO_PE_OE"
+	depends on ETRAX_ARCH_V32
+	default "00000"
+	help
+	  Configures the direction of general port E bits.  1 is out, 0 is in.
+	  This is often totally different depending on the product used.
+	  There are some guidelines though - if you know that only LED's are
+	  connected to port PA, then they are usually connected to bits 2-4
+	  and you can therefore use 1c.  On other boards which don't have the
+	  LED's at the general ports, these bits are used for all kinds of
+	  stuff.  If you don't know what to use, it is always safe to put all
+	  as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PE_OUT
+	hex "GIO_PE_OUT"
+	depends on ETRAX_ARCH_V32
+	default "00000"
+	help
+	  Configures the initial data for the general port E bits.  Most
+	  products should use 00000 here.