x86: move i386 and x86_64 Kconfig files to x86 directory

After a small change in kconfig Makefile we could
move all x86 Kconfig files to x86 directory.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

3 files changed, 2537 insertions, 0 deletions

diff --git a/arch/x86/Kconfig.cpu b/arch/x86/Kconfig.cpu
new file mode 100644
index 00000000000..0e2adadf590
--- /dev/null
+++ b/arch/x86/Kconfig.cpu
@@ -0,0 +1,372 @@
+# Put here option for CPU selection and depending optimization
+if !X86_ELAN
+
+choice
+	prompt "Processor family"
+	default M686
+
+config M386
+	bool "386"
+	depends on !UML
+	---help---
+	  This is the processor type of your CPU. This information is used for
+	  optimizing purposes. In order to compile a kernel that can run on
+	  all x86 CPU types (albeit not optimally fast), you can specify
+	  "386" here.
+
+	  The kernel will not necessarily run on earlier architectures than
+	  the one you have chosen, e.g. a Pentium optimized kernel will run on
+	  a PPro, but not necessarily on a i486.
+
+	  Here are the settings recommended for greatest speed:
+	  - "386" for the AMD/Cyrix/Intel 386DX/DXL/SL/SLC/SX, Cyrix/TI
+	  486DLC/DLC2, UMC 486SX-S and NexGen Nx586.  Only "386" kernels
+	  will run on a 386 class machine.
+	  - "486" for the AMD/Cyrix/IBM/Intel 486DX/DX2/DX4 or
+	  SL/SLC/SLC2/SLC3/SX/SX2 and UMC U5D or U5S.
+	  - "586" for generic Pentium CPUs lacking the TSC
+	  (time stamp counter) register.
+	  - "Pentium-Classic" for the Intel Pentium.
+	  - "Pentium-MMX" for the Intel Pentium MMX.
+	  - "Pentium-Pro" for the Intel Pentium Pro.
+	  - "Pentium-II" for the Intel Pentium II or pre-Coppermine Celeron.
+	  - "Pentium-III" for the Intel Pentium III or Coppermine Celeron.
+	  - "Pentium-4" for the Intel Pentium 4 or P4-based Celeron.
+	  - "K6" for the AMD K6, K6-II and K6-III (aka K6-3D).
+	  - "Athlon" for the AMD K7 family (Athlon/Duron/Thunderbird).
+	  - "Crusoe" for the Transmeta Crusoe series.
+	  - "Efficeon" for the Transmeta Efficeon series.
+	  - "Winchip-C6" for original IDT Winchip.
+	  - "Winchip-2" for IDT Winchip 2.
+	  - "Winchip-2A" for IDT Winchips with 3dNow! capabilities.
+	  - "GeodeGX1" for Geode GX1 (Cyrix MediaGX).
+	  - "Geode GX/LX" For AMD Geode GX and LX processors.
+	  - "CyrixIII/VIA C3" for VIA Cyrix III or VIA C3.
+	  - "VIA C3-2" for VIA C3-2 "Nehemiah" (model 9 and above).
+	  - "VIA C7" for VIA C7.
+
+	  If you don't know what to do, choose "386".
+
+config M486
+	bool "486"
+	help
+	  Select this for a 486 series processor, either Intel or one of the
+	  compatible processors from AMD, Cyrix, IBM, or Intel.  Includes DX,
+	  DX2, and DX4 variants; also SL/SLC/SLC2/SLC3/SX/SX2 and UMC U5D or
+	  U5S.
+
+config M586
+	bool "586/K5/5x86/6x86/6x86MX"
+	help
+	  Select this for an 586 or 686 series processor such as the AMD K5,
+	  the Cyrix 5x86, 6x86 and 6x86MX.  This choice does not
+	  assume the RDTSC (Read Time Stamp Counter) instruction.
+
+config M586TSC
+	bool "Pentium-Classic"
+	help
+	  Select this for a Pentium Classic processor with the RDTSC (Read
+	  Time Stamp Counter) instruction for benchmarking.
+
+config M586MMX
+	bool "Pentium-MMX"
+	help
+	  Select this for a Pentium with the MMX graphics/multimedia
+	  extended instructions.
+
+config M686
+	bool "Pentium-Pro"
+	help
+	  Select this for Intel Pentium Pro chips.  This enables the use of
+	  Pentium Pro extended instructions, and disables the init-time guard
+	  against the f00f bug found in earlier Pentiums.
+
+config MPENTIUMII
+	bool "Pentium-II/Celeron(pre-Coppermine)"
+	help
+	  Select this for Intel chips based on the Pentium-II and
+	  pre-Coppermine Celeron core.  This option enables an unaligned
+	  copy optimization, compiles the kernel with optimization flags
+	  tailored for the chip, and applies any applicable Pentium Pro
+	  optimizations.
+
+config MPENTIUMIII
+	bool "Pentium-III/Celeron(Coppermine)/Pentium-III Xeon"
+	help
+	  Select this for Intel chips based on the Pentium-III and
+	  Celeron-Coppermine core.  This option enables use of some
+	  extended prefetch instructions in addition to the Pentium II
+	  extensions.
+
+config MPENTIUMM
+	bool "Pentium M"
+	help
+	  Select this for Intel Pentium M (not Pentium-4 M)
+	  notebook chips.
+
+config MCORE2
+	bool "Core 2/newer Xeon"
+	help
+	  Select this for Intel Core 2 and newer Core 2 Xeons (Xeon 51xx and 53xx)
+	  CPUs. You can distinguish newer from older Xeons by the CPU family
+	  in /proc/cpuinfo. Newer ones have 6 and older ones 15 (not a typo)
+
+config MPENTIUM4
+	bool "Pentium-4/Celeron(P4-based)/Pentium-4 M/older Xeon"
+	help
+	  Select this for Intel Pentium 4 chips.  This includes the
+	  Pentium 4, Pentium D, P4-based Celeron and Xeon, and
+	  Pentium-4 M (not Pentium M) chips.  This option enables compile
+	  flags optimized for the chip, uses the correct cache line size, and
+	  applies any applicable optimizations.
+
+	  CPUIDs: F[0-6][1-A] (in /proc/cpuinfo show = cpu family : 15 )
+
+	  Select this for:
+	    Pentiums (Pentium 4, Pentium D, Celeron, Celeron D) corename:
+		-Willamette
+		-Northwood
+		-Mobile Pentium 4
+		-Mobile Pentium 4 M
+		-Extreme Edition (Gallatin)
+		-Prescott
+		-Prescott 2M
+		-Cedar Mill
+		-Presler
+		-Smithfiled
+	    Xeons (Intel Xeon, Xeon MP, Xeon LV, Xeon MV) corename:
+		-Foster
+		-Prestonia
+		-Gallatin
+		-Nocona
+		-Irwindale
+		-Cranford
+		-Potomac
+		-Paxville
+		-Dempsey
+
+
+config MK6
+	bool "K6/K6-II/K6-III"
+	help
+	  Select this for an AMD K6-family processor.  Enables use of
+	  some extended instructions, and passes appropriate optimization
+	  flags to GCC.
+
+config MK7
+	bool "Athlon/Duron/K7"
+	help
+	  Select this for an AMD Athlon K7-family processor.  Enables use of
+	  some extended instructions, and passes appropriate optimization
+	  flags to GCC.
+
+config MK8
+	bool "Opteron/Athlon64/Hammer/K8"
+	help
+	  Select this for an AMD Opteron or Athlon64 Hammer-family processor.  Enables
+	  use of some extended instructions, and passes appropriate optimization
+	  flags to GCC.
+
+config MCRUSOE
+	bool "Crusoe"
+	help
+	  Select this for a Transmeta Crusoe processor.  Treats the processor
+	  like a 586 with TSC, and sets some GCC optimization flags (like a
+	  Pentium Pro with no alignment requirements).
+
+config MEFFICEON
+	bool "Efficeon"
+	help
+	  Select this for a Transmeta Efficeon processor.
+
+config MWINCHIPC6
+	bool "Winchip-C6"
+	help
+	  Select this for an IDT Winchip C6 chip.  Linux and GCC
+	  treat this chip as a 586TSC with some extended instructions
+	  and alignment requirements.
+
+config MWINCHIP2
+	bool "Winchip-2"
+	help
+	  Select this for an IDT Winchip-2.  Linux and GCC
+	  treat this chip as a 586TSC with some extended instructions
+	  and alignment requirements.
+
+config MWINCHIP3D
+	bool "Winchip-2A/Winchip-3"
+	help
+	  Select this for an IDT Winchip-2A or 3.  Linux and GCC
+	  treat this chip as a 586TSC with some extended instructions
+	  and alignment requirements.  Also enable out of order memory
+	  stores for this CPU, which can increase performance of some
+	  operations.
+
+config MGEODEGX1
+	bool "GeodeGX1"
+	help
+	  Select this for a Geode GX1 (Cyrix MediaGX) chip.
+
+config MGEODE_LX
+       bool "Geode GX/LX"
+       help
+         Select this for AMD Geode GX and LX processors.
+
+config MCYRIXIII
+	bool "CyrixIII/VIA-C3"
+	help
+	  Select this for a Cyrix III or C3 chip.  Presently Linux and GCC
+	  treat this chip as a generic 586. Whilst the CPU is 686 class,
+	  it lacks the cmov extension which gcc assumes is present when
+	  generating 686 code.
+	  Note that Nehemiah (Model 9) and above will not boot with this
+	  kernel due to them lacking the 3DNow! instructions used in earlier
+	  incarnations of the CPU.
+
+config MVIAC3_2
+	bool "VIA C3-2 (Nehemiah)"
+	help
+	  Select this for a VIA C3 "Nehemiah". Selecting this enables usage
+	  of SSE and tells gcc to treat the CPU as a 686.
+	  Note, this kernel will not boot on older (pre model 9) C3s.
+
+config MVIAC7
+	bool "VIA C7"
+	help
+	  Select this for a VIA C7.  Selecting this uses the correct cache
+	  shift and tells gcc to treat the CPU as a 686.
+
+endchoice
+
+config X86_GENERIC
+       bool "Generic x86 support"
+       help
+	  Instead of just including optimizations for the selected
+	  x86 variant (e.g. PII, Crusoe or Athlon), include some more
+	  generic optimizations as well. This will make the kernel
+	  perform better on x86 CPUs other than that selected.
+
+	  This is really intended for distributors who need more
+	  generic optimizations.
+
+endif
+
+#
+# Define implied options from the CPU selection here
+#
+config X86_CMPXCHG
+	bool
+	depends on !M386
+	default y
+
+config X86_L1_CACHE_SHIFT
+	int
+	default "7" if MPENTIUM4 || X86_GENERIC
+	default "4" if X86_ELAN || M486 || M386 || MGEODEGX1
+	default "5" if MWINCHIP3D || MWINCHIP2 || MWINCHIPC6 || MCRUSOE || MEFFICEON || MCYRIXIII || MK6 || MPENTIUMIII || MPENTIUMII || M686 || M586MMX || M586TSC || M586 || MVIAC3_2 || MGEODE_LX
+	default "6" if MK7 || MK8 || MPENTIUMM || MCORE2 || MVIAC7
+
+config X86_XADD
+	bool
+	depends on !M386
+	default y
+
+config RWSEM_GENERIC_SPINLOCK
+	bool
+	depends on !X86_XADD
+	default y
+
+config RWSEM_XCHGADD_ALGORITHM
+	bool
+	depends on X86_XADD
+	default y
+
+config ARCH_HAS_ILOG2_U32
+	bool
+	default n
+
+config ARCH_HAS_ILOG2_U64
+	bool
+	default n
+
+config GENERIC_CALIBRATE_DELAY
+	bool
+	default y
+
+config X86_PPRO_FENCE
+	bool
+	depends on M686 || M586MMX || M586TSC || M586 || M486 || M386 || MGEODEGX1
+	default y
+
+config X86_F00F_BUG
+	bool
+	depends on M586MMX || M586TSC || M586 || M486 || M386
+	default y
+
+config X86_WP_WORKS_OK
+	bool
+	depends on !M386
+	default y
+
+config X86_INVLPG
+	bool
+	depends on !M386
+	default y
+
+config X86_BSWAP
+	bool
+	depends on !M386
+	default y
+
+config X86_POPAD_OK
+	bool
+	depends on !M386
+	default y
+
+config X86_ALIGNMENT_16
+	bool
+	depends on MWINCHIP3D || MWINCHIP2 || MWINCHIPC6 || MCYRIXIII || X86_ELAN || MK6 || M586MMX || M586TSC || M586 || M486 || MVIAC3_2 || MGEODEGX1
+	default y
+
+config X86_GOOD_APIC
+	bool
+	depends on MK7 || MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || M586MMX || MK8 || MEFFICEON || MCORE2 || MVIAC7
+	default y
+
+config X86_INTEL_USERCOPY
+	bool
+	depends on MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M586MMX || X86_GENERIC || MK8 || MK7 || MEFFICEON || MCORE2
+	default y
+
+config X86_USE_PPRO_CHECKSUM
+	bool
+	depends on MWINCHIP3D || MWINCHIP2 || MWINCHIPC6 || MCYRIXIII || MK7 || MK6 || MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || MK8 || MVIAC3_2 || MEFFICEON || MGEODE_LX || MCORE2
+	default y
+
+config X86_USE_3DNOW
+	bool
+	depends on (MCYRIXIII || MK7 || MGEODE_LX) && !UML
+	default y
+
+config X86_OOSTORE
+	bool
+	depends on (MWINCHIP3D || MWINCHIP2 || MWINCHIPC6) && MTRR
+	default y
+
+config X86_TSC
+	bool
+	depends on (MWINCHIP3D || MWINCHIP2 || MCRUSOE || MEFFICEON || MCYRIXIII || MK7 || MK6 || MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || M586MMX || M586TSC || MK8 || MVIAC3_2 || MVIAC7 || MGEODEGX1 || MGEODE_LX || MCORE2) && !X86_NUMAQ
+	default y
+
+# this should be set for all -march=.. options where the compiler
+# generates cmov.
+config X86_CMOV
+	bool
+	depends on (MK7 || MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || MVIAC3_2 || MVIAC7)
+	default y
+
+config X86_MINIMUM_CPU_FAMILY
+	int
+	default "4" if X86_XADD || X86_CMPXCHG || X86_BSWAP || X86_WP_WORKS_OK
+	default "3"
+
diff --git a/arch/x86/Kconfig.i386 b/arch/x86/Kconfig.i386
new file mode 100644
index 00000000000..7331efe891a
--- /dev/null
+++ b/arch/x86/Kconfig.i386
@@ -0,0 +1,1321 @@
+#
+# For a description of the syntax of this configuration file,
+# see Documentation/kbuild/kconfig-language.txt.
+#
+
+mainmenu "Linux Kernel Configuration"
+
+config X86_32
+	bool
+	default y
+	help
+	  This is Linux's home port.  Linux was originally native to the Intel
+	  386, and runs on all the later x86 processors including the Intel
+	  486, 586, Pentiums, and various instruction-set-compatible chips by
+	  AMD, Cyrix, and others.
+
+config GENERIC_TIME
+	bool
+	default y
+
+config GENERIC_CMOS_UPDATE
+	bool
+	default y
+
+config CLOCKSOURCE_WATCHDOG
+	bool
+	default y
+
+config GENERIC_CLOCKEVENTS
+	bool
+	default y
+
+config GENERIC_CLOCKEVENTS_BROADCAST
+	bool
+	default y
+	depends on X86_LOCAL_APIC
+
+config LOCKDEP_SUPPORT
+	bool
+	default y
+
+config STACKTRACE_SUPPORT
+	bool
+	default y
+
+config SEMAPHORE_SLEEPERS
+	bool
+	default y
+
+config X86
+	bool
+	default y
+
+config MMU
+	bool
+	default y
+
+config ZONE_DMA
+	bool
+	default y
+
+config QUICKLIST
+	bool
+	default y
+
+config SBUS
+	bool
+
+config GENERIC_ISA_DMA
+	bool
+	default y
+
+config GENERIC_IOMAP
+	bool
+	default y
+
+config GENERIC_BUG
+	bool
+	default y
+	depends on BUG
+
+config GENERIC_HWEIGHT
+	bool
+	default y
+
+config ARCH_MAY_HAVE_PC_FDC
+	bool
+	default y
+
+config DMI
+	bool
+	default y
+
+source "init/Kconfig"
+
+menu "Processor type and features"
+
+source "kernel/time/Kconfig"
+
+config SMP
+	bool "Symmetric multi-processing support"
+	---help---
+	  This enables support for systems with more than one CPU. If you have
+	  a system with only one CPU, like most personal computers, say N. If
+	  you have a system with more than one CPU, say Y.
+
+	  If you say N here, the kernel will run on single and multiprocessor
+	  machines, but will use only one CPU of a multiprocessor machine. If
+	  you say Y here, the kernel will run on many, but not all,
+	  singleprocessor machines. On a singleprocessor machine, the kernel
+	  will run faster if you say N here.
+
+	  Note that if you say Y here and choose architecture "586" or
+	  "Pentium" under "Processor family", the kernel will not work on 486
+	  architectures. Similarly, multiprocessor kernels for the "PPro"
+	  architecture may not work on all Pentium based boards.
+
+	  People using multiprocessor machines who say Y here should also say
+	  Y to "Enhanced Real Time Clock Support", below. The "Advanced Power
+	  Management" code will be disabled if you say Y here.
+
+	  See also the <file:Documentation/smp.txt>,
+	  <file:Documentation/i386/IO-APIC.txt>,
+	  <file:Documentation/nmi_watchdog.txt> and the SMP-HOWTO available at
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  If you don't know what to do here, say N.
+
+choice
+	prompt "Subarchitecture Type"
+	default X86_PC
+
+config X86_PC
+	bool "PC-compatible"
+	help
+	  Choose this option if your computer is a standard PC or compatible.
+
+config X86_ELAN
+	bool "AMD Elan"
+	help
+	  Select this for an AMD Elan processor.
+
+	  Do not use this option for K6/Athlon/Opteron processors!
+
+	  If unsure, choose "PC-compatible" instead.
+
+config X86_VOYAGER
+	bool "Voyager (NCR)"
+	select SMP if !BROKEN
+	help
+	  Voyager is an MCA-based 32-way capable SMP architecture proprietary
+	  to NCR Corp.  Machine classes 345x/35xx/4100/51xx are Voyager-based.
+
+	  *** WARNING ***
+
+	  If you do not specifically know you have a Voyager based machine,
+	  say N here, otherwise the kernel you build will not be bootable.
+
+config X86_NUMAQ
+	bool "NUMAQ (IBM/Sequent)"
+	select SMP
+	select NUMA
+	help
+	  This option is used for getting Linux to run on a (IBM/Sequent) NUMA
+	  multiquad box. This changes the way that processors are bootstrapped,
+	  and uses Clustered Logical APIC addressing mode instead of Flat Logical.
+	  You will need a new lynxer.elf file to flash your firmware with - send
+	  email to <Martin.Bligh@us.ibm.com>.
+
+config X86_SUMMIT
+	bool "Summit/EXA (IBM x440)"
+	depends on SMP
+	help
+	  This option is needed for IBM systems that use the Summit/EXA chipset.
+	  In particular, it is needed for the x440.
+
+	  If you don't have one of these computers, you should say N here.
+	  If you want to build a NUMA kernel, you must select ACPI.
+
+config X86_BIGSMP
+	bool "Support for other sub-arch SMP systems with more than 8 CPUs"
+	depends on SMP
+	help
+	  This option is needed for the systems that have more than 8 CPUs
+	  and if the system is not of any sub-arch type above.
+
+	  If you don't have such a system, you should say N here.
+
+config X86_VISWS
+	bool "SGI 320/540 (Visual Workstation)"
+	help
+	  The SGI Visual Workstation series is an IA32-based workstation
+	  based on SGI systems chips with some legacy PC hardware attached.
+
+	  Say Y here to create a kernel to run on the SGI 320 or 540.
+
+	  A kernel compiled for the Visual Workstation will not run on PCs
+	  and vice versa. See <file:Documentation/sgi-visws.txt> for details.
+
+config X86_GENERICARCH
+       bool "Generic architecture (Summit, bigsmp, ES7000, default)"
+       help
+          This option compiles in the Summit, bigsmp, ES7000, default subarchitectures.
+	  It is intended for a generic binary kernel.
+	  If you want a NUMA kernel, select ACPI.   We need SRAT for NUMA.
+
+config X86_ES7000
+	bool "Support for Unisys ES7000 IA32 series"
+	depends on SMP
+	help
+	  Support for Unisys ES7000 systems.  Say 'Y' here if this kernel is
+	  supposed to run on an IA32-based Unisys ES7000 system.
+	  Only choose this option if you have such a system, otherwise you
+	  should say N here.
+
+endchoice
+
+config SCHED_NO_NO_OMIT_FRAME_POINTER
+	bool "Single-depth WCHAN output"
+	default y
+	help
+	  Calculate simpler /proc/<PID>/wchan values. If this option
+	  is disabled then wchan values will recurse back to the
+	  caller function. This provides more accurate wchan values,
+	  at the expense of slightly more scheduling overhead.
+
+	  If in doubt, say "Y".
+
+config PARAVIRT
+	bool
+	depends on !(X86_VISWS || X86_VOYAGER)
+	help
+	  This changes the kernel so it can modify itself when it is run
+	  under a hypervisor, potentially improving performance significantly
+	  over full virtualization.  However, when run without a hypervisor
+	  the kernel is theoretically slower and slightly larger.
+
+menuconfig PARAVIRT_GUEST
+	bool "Paravirtualized guest support"
+	help
+	  Say Y here to get to see options related to running Linux under
+	  various hypervisors.  This option alone does not add any kernel code.
+
+	  If you say N, all options in this submenu will be skipped and disabled.
+
+if PARAVIRT_GUEST
+
+source "arch/x86/xen/Kconfig"
+
+config VMI
+	bool "VMI Guest support"
+	select PARAVIRT
+	depends on !(X86_VISWS || X86_VOYAGER)
+	help
+	  VMI provides a paravirtualized interface to the VMware ESX server
+	  (it could be used by other hypervisors in theory too, but is not
+	  at the moment), by linking the kernel to a GPL-ed ROM module
+	  provided by the hypervisor.
+
+source "arch/x86/lguest/Kconfig"
+
+endif
+
+config ACPI_SRAT
+	bool
+	default y
+	depends on ACPI && NUMA && (X86_SUMMIT || X86_GENERICARCH)
+	select ACPI_NUMA
+
+config HAVE_ARCH_PARSE_SRAT
+       bool
+       default y
+       depends on ACPI_SRAT
+
+config X86_SUMMIT_NUMA
+	bool
+	default y
+	depends on NUMA && (X86_SUMMIT || X86_GENERICARCH)
+
+config X86_CYCLONE_TIMER
+	bool
+	default y
+	depends on X86_SUMMIT || X86_GENERICARCH
+
+config ES7000_CLUSTERED_APIC
+	bool
+	default y
+	depends on SMP && X86_ES7000 && MPENTIUMIII
+
+source "arch/x86/Kconfig.cpu"
+
+config HPET_TIMER
+	bool "HPET Timer Support"
+	help
+	  This enables the use of the HPET for the kernel's internal timer.
+	  HPET is the next generation timer replacing legacy 8254s.
+	  You can safely choose Y here.  However, HPET will only be
+	  activated if the platform and the BIOS support this feature.
+	  Otherwise the 8254 will be used for timing services.
+
+	  Choose N to continue using the legacy 8254 timer.
+
+config HPET_EMULATE_RTC
+	bool
+	depends on HPET_TIMER && RTC=y
+	default y
+
+config NR_CPUS
+	int "Maximum number of CPUs (2-255)"
+	range 2 255
+	depends on SMP
+	default "32" if X86_NUMAQ || X86_SUMMIT || X86_BIGSMP || X86_ES7000
+	default "8"
+	help
+	  This allows you to specify the maximum number of CPUs which this
+	  kernel will support.  The maximum supported value is 255 and the
+	  minimum value which makes sense is 2.
+
+	  This is purely to save memory - each supported CPU adds
+	  approximately eight kilobytes to the kernel image.
+
+config SCHED_SMT
+	bool "SMT (Hyperthreading) scheduler support"
+	depends on X86_HT
+	help
+	  SMT scheduler support improves the CPU scheduler's decision making
+	  when dealing with Intel Pentium 4 chips with HyperThreading at a
+	  cost of slightly increased overhead in some places. If unsure say
+	  N here.
+
+config SCHED_MC
+	bool "Multi-core scheduler support"
+	depends on X86_HT
+	default y
+	help
+	  Multi-core scheduler support improves the CPU scheduler's decision
+	  making when dealing with multi-core CPU chips at a cost of slightly
+	  increased overhead in some places. If unsure say N here.
+
+source "kernel/Kconfig.preempt"
+
+config X86_UP_APIC
+	bool "Local APIC support on uniprocessors"
+	depends on !SMP && !(X86_VISWS || X86_VOYAGER || X86_GENERICARCH)
+	help
+	  A local APIC (Advanced Programmable Interrupt Controller) is an
+	  integrated interrupt controller in the CPU. If you have a single-CPU
+	  system which has a processor with a local APIC, you can say Y here to
+	  enable and use it. If you say Y here even though your machine doesn't
+	  have a local APIC, then the kernel will still run with no slowdown at
+	  all. The local APIC supports CPU-generated self-interrupts (timer,
+	  performance counters), and the NMI watchdog which detects hard
+	  lockups.
+
+config X86_UP_IOAPIC
+	bool "IO-APIC support on uniprocessors"
+	depends on X86_UP_APIC
+	help
+	  An IO-APIC (I/O Advanced Programmable Interrupt Controller) is an
+	  SMP-capable replacement for PC-style interrupt controllers. Most
+	  SMP systems and many recent uniprocessor systems have one.
+
+	  If you have a single-CPU system with an IO-APIC, you can say Y here
+	  to use it. If you say Y here even though your machine doesn't have
+	  an IO-APIC, then the kernel will still run with no slowdown at all.
+
+config X86_LOCAL_APIC
+	bool
+	depends on X86_UP_APIC || ((X86_VISWS || SMP) && !X86_VOYAGER) || X86_GENERICARCH
+	default y
+
+config X86_IO_APIC
+	bool
+	depends on X86_UP_IOAPIC || (SMP && !(X86_VISWS || X86_VOYAGER)) || X86_GENERICARCH
+	default y
+
+config X86_VISWS_APIC
+	bool
+	depends on X86_VISWS
+	default y
+
+config X86_MCE
+	bool "Machine Check Exception"
+	depends on !X86_VOYAGER
+	---help---
+	  Machine Check Exception support allows the processor to notify the
+	  kernel if it detects a problem (e.g. overheating, component failure).
+	  The action the kernel takes depends on the severity of the problem,
+	  ranging from a warning message on the console, to halting the machine.
+	  Your processor must be a Pentium or newer to support this - check the
+	  flags in /proc/cpuinfo for mce.  Note that some older Pentium systems
+	  have a design flaw which leads to false MCE events - hence MCE is
+	  disabled on all P5 processors, unless explicitly enabled with "mce"
+	  as a boot argument.  Similarly, if MCE is built in and creates a
+	  problem on some new non-standard machine, you can boot with "nomce"
+	  to disable it.  MCE support simply ignores non-MCE processors like
+	  the 386 and 486, so nearly everyone can say Y here.
+
+config X86_MCE_NONFATAL
+	tristate "Check for non-fatal errors on AMD Athlon/Duron / Intel Pentium 4"
+	depends on X86_MCE
+	help
+	  Enabling this feature starts a timer that triggers every 5 seconds which
+	  will look at the machine check registers to see if anything happened.
+	  Non-fatal problems automatically get corrected (but still logged).
+	  Disable this if you don't want to see these messages.
+	  Seeing the messages this option prints out may be indicative of dying
+	  or out-of-spec (ie, overclocked) hardware.
+	  This option only does something on certain CPUs.
+	  (AMD Athlon/Duron and Intel Pentium 4)
+
+config X86_MCE_P4THERMAL
+	bool "check for P4 thermal throttling interrupt."
+	depends on X86_MCE && (X86_UP_APIC || SMP) && !X86_VISWS
+	help
+	  Enabling this feature will cause a message to be printed when the P4
+	  enters thermal throttling.
+
+config VM86
+	default y
+	bool "Enable VM86 support" if EMBEDDED
+	help
+          This option is required by programs like DOSEMU to run 16-bit legacy
+	  code on X86 processors. It also may be needed by software like
+          XFree86 to initialize some video cards via BIOS. Disabling this
+          option saves about 6k.
+
+config TOSHIBA
+	tristate "Toshiba Laptop support"
+	---help---
+	  This adds a driver to safely access the System Management Mode of
+	  the CPU on Toshiba portables with a genuine Toshiba BIOS. It does
+	  not work on models with a Phoenix BIOS. The System Management Mode
+	  is used to set the BIOS and power saving options on Toshiba portables.
+
+	  For information on utilities to make use of this driver see the
+	  Toshiba Linux utilities web site at:
+	  <http://www.buzzard.org.uk/toshiba/>.
+
+	  Say Y if you intend to run this kernel on a Toshiba portable.
+	  Say N otherwise.
+
+config I8K
+	tristate "Dell laptop support"
+	---help---
+	  This adds a driver to safely access the System Management Mode
+	  of the CPU on the Dell Inspiron 8000. The System Management Mode
+	  is used to read cpu temperature and cooling fan status and to
+	  control the fans on the I8K portables.
+
+	  This driver has been tested only on the Inspiron 8000 but it may
+	  also work with other Dell laptops. You can force loading on other
+	  models by passing the parameter `force=1' to the module. Use at
+	  your own risk.
+
+	  For information on utilities to make use of this driver see the
+	  I8K Linux utilities web site at:
+	  <http://people.debian.org/~dz/i8k/>
+
+	  Say Y if you intend to run this kernel on a Dell Inspiron 8000.
+	  Say N otherwise.
+
+config X86_REBOOTFIXUPS
+	bool "Enable X86 board specific fixups for reboot"
+	depends on X86
+	default n
+	---help---
+	  This enables chipset and/or board specific fixups to be done
+	  in order to get reboot to work correctly. This is only needed on
+	  some combinations of hardware and BIOS. The symptom, for which
+	  this config is intended, is when reboot ends with a stalled/hung
+	  system.
+
+	  Currently, the only fixup is for the Geode machines using
+	  CS5530A and CS5536 chipsets.
+
+	  Say Y if you want to enable the fixup. Currently, it's safe to
+	  enable this option even if you don't need it.
+	  Say N otherwise.
+
+config MICROCODE
+	tristate "/dev/cpu/microcode - Intel IA32 CPU microcode support"
+	select FW_LOADER
+	---help---
+	  If you say Y here, you will be able to update the microcode on
+	  Intel processors in the IA32 family, e.g. Pentium Pro, Pentium II,
+	  Pentium III, Pentium 4, Xeon etc.  You will obviously need the
+	  actual microcode binary data itself which is not shipped with the
+	  Linux kernel.
+
+	  For latest news and information on obtaining all the required
+	  ingredients for this driver, check:
+	  <http://www.urbanmyth.org/microcode/>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called microcode.
+
+config MICROCODE_OLD_INTERFACE
+	bool
+	depends on MICROCODE
+	default y
+
+config X86_MSR
+	tristate "/dev/cpu/*/msr - Model-specific register support"
+	help
+	  This device gives privileged processes access to the x86
+	  Model-Specific Registers (MSRs).  It is a character device with
+	  major 202 and minors 0 to 31 for /dev/cpu/0/msr to /dev/cpu/31/msr.
+	  MSR accesses are directed to a specific CPU on multi-processor
+	  systems.
+
+config X86_CPUID
+	tristate "/dev/cpu/*/cpuid - CPU information support"
+	help
+	  This device gives processes access to the x86 CPUID instruction to
+	  be executed on a specific processor.  It is a character device
+	  with major 203 and minors 0 to 31 for /dev/cpu/0/cpuid to
+	  /dev/cpu/31/cpuid.
+
+source "drivers/firmware/Kconfig"
+
+choice
+	prompt "High Memory Support"
+	default HIGHMEM4G if !X86_NUMAQ
+	default HIGHMEM64G if X86_NUMAQ
+
+config NOHIGHMEM
+	bool "off"
+	depends on !X86_NUMAQ
+	---help---
+	  Linux can use up to 64 Gigabytes of physical memory on x86 systems.
+	  However, the address space of 32-bit x86 processors is only 4
+	  Gigabytes large. That means that, if you have a large amount of
+	  physical memory, not all of it can be "permanently mapped" by the
+	  kernel. The physical memory that's not permanently mapped is called
+	  "high memory".
+
+	  If you are compiling a kernel which will never run on a machine with
+	  more than 1 Gigabyte total physical RAM, answer "off" here (default
+	  choice and suitable for most users). This will result in a "3GB/1GB"
+	  split: 3GB are mapped so that each process sees a 3GB virtual memory
+	  space and the remaining part of the 4GB virtual memory space is used
+	  by the kernel to permanently map as much physical memory as
+	  possible.
+
+	  If the machine has between 1 and 4 Gigabytes physical RAM, then
+	  answer "4GB" here.
+
+	  If more than 4 Gigabytes is used then answer "64GB" here. This
+	  selection turns Intel PAE (Physical Address Extension) mode on.
+	  PAE implements 3-level paging on IA32 processors. PAE is fully
+	  supported by Linux, PAE mode is implemented on all recent Intel
+	  processors (Pentium Pro and better). NOTE: If you say "64GB" here,
+	  then the kernel will not boot on CPUs that don't support PAE!
+
+	  The actual amount of total physical memory will either be
+	  auto detected or can be forced by using a kernel command line option
+	  such as "mem=256M". (Try "man bootparam" or see the documentation of
+	  your boot loader (lilo or loadlin) about how to pass options to the
+	  kernel at boot time.)
+
+	  If unsure, say "off".
+
+config HIGHMEM4G
+	bool "4GB"
+	depends on !X86_NUMAQ
+	help
+	  Select this if you have a 32-bit processor and between 1 and 4
+	  gigabytes of physical RAM.
+
+config HIGHMEM64G
+	bool "64GB"
+	depends on !M386 && !M486
+	select X86_PAE
+	help
+	  Select this if you have a 32-bit processor and more than 4
+	  gigabytes of physical RAM.
+
+endchoice
+
+choice
+	depends on EXPERIMENTAL
+	prompt "Memory split" if EMBEDDED
+	default VMSPLIT_3G
+	help
+	  Select the desired split between kernel and user memory.
+
+	  If the address range available to the kernel is less than the
+	  physical memory installed, the remaining memory will be available
+	  as "high memory". Accessing high memory is a little more costly
+	  than low memory, as it needs to be mapped into the kernel first.
+	  Note that increasing the kernel address space limits the range
+	  available to user programs, making the address space there
+	  tighter.  Selecting anything other than the default 3G/1G split
+	  will also likely make your kernel incompatible with binary-only
+	  kernel modules.
+
+	  If you are not absolutely sure what you are doing, leave this
+	  option alone!
+
+	config VMSPLIT_3G
+		bool "3G/1G user/kernel split"
+	config VMSPLIT_3G_OPT
+		depends on !X86_PAE
+		bool "3G/1G user/kernel split (for full 1G low memory)"
+	config VMSPLIT_2G
+		bool "2G/2G user/kernel split"
+	config VMSPLIT_2G_OPT
+		depends on !X86_PAE
+		bool "2G/2G user/kernel split (for full 2G low memory)"
+	config VMSPLIT_1G
+		bool "1G/3G user/kernel split"
+endchoice
+
+config PAGE_OFFSET
+	hex
+	default 0xB0000000 if VMSPLIT_3G_OPT
+	default 0x80000000 if VMSPLIT_2G
+	default 0x78000000 if VMSPLIT_2G_OPT
+	default 0x40000000 if VMSPLIT_1G
+	default 0xC0000000
+
+config HIGHMEM
+	bool
+	depends on HIGHMEM64G || HIGHMEM4G
+	default y
+
+config X86_PAE
+	bool "PAE (Physical Address Extension) Support"
+	default n
+	depends on !HIGHMEM4G
+	select RESOURCES_64BIT
+	help
+	  PAE is required for NX support, and furthermore enables
+	  larger swapspace support for non-overcommit purposes. It
+	  has the cost of more pagetable lookup overhead, and also
+	  consumes more pagetable space per process.
+
+# Common NUMA Features
+config NUMA
+	bool "Numa Memory Allocation and Scheduler Support (EXPERIMENTAL)"
+	depends on SMP && HIGHMEM64G && (X86_NUMAQ || (X86_SUMMIT || X86_GENERICARCH) && ACPI) && EXPERIMENTAL
+	default n if X86_PC
+	default y if (X86_NUMAQ || X86_SUMMIT)
+	help
+	  NUMA support for i386. This is currently highly experimental
+	  and should be only used for kernel development. It might also
+	  cause boot failures.
+
+comment "NUMA (Summit) requires SMP, 64GB highmem support, ACPI"
+	depends on X86_SUMMIT && (!HIGHMEM64G || !ACPI)
+
+config NODES_SHIFT
+	int
+	default "4" if X86_NUMAQ
+	default "3"
+	depends on NEED_MULTIPLE_NODES
+
+config HAVE_ARCH_BOOTMEM_NODE
+	bool
+	depends on NUMA
+	default y
+
+config ARCH_HAVE_MEMORY_PRESENT
+	bool
+	depends on DISCONTIGMEM
+	default y
+
+config NEED_NODE_MEMMAP_SIZE
+	bool
+	depends on DISCONTIGMEM || SPARSEMEM
+	default y
+
+config HAVE_ARCH_ALLOC_REMAP
+	bool
+	depends on NUMA
+	default y
+
+config ARCH_FLATMEM_ENABLE
+	def_bool y
+	depends on (ARCH_SELECT_MEMORY_MODEL && X86_PC)
+
+config ARCH_DISCONTIGMEM_ENABLE
+	def_bool y
+	depends on NUMA
+
+config ARCH_DISCONTIGMEM_DEFAULT
+	def_bool y
+	depends on NUMA
+
+config ARCH_SPARSEMEM_ENABLE
+	def_bool y
+	depends on (NUMA || (X86_PC && EXPERIMENTAL))
+	select SPARSEMEM_STATIC
+
+config ARCH_SELECT_MEMORY_MODEL
+	def_bool y
+	depends on ARCH_SPARSEMEM_ENABLE
+
+config ARCH_POPULATES_NODE_MAP
+	def_bool y
+
+source "mm/Kconfig"
+
+config HIGHPTE
+	bool "Allocate 3rd-level pagetables from highmem"
+	depends on HIGHMEM4G || HIGHMEM64G
+	help
+	  The VM uses one page table entry for each page of physical memory.
+	  For systems with a lot of RAM, this can be wasteful of precious
+	  low memory.  Setting this option will put user-space page table
+	  entries in high memory.
+
+config MATH_EMULATION
+	bool "Math emulation"
+	---help---
+	  Linux can emulate a math coprocessor (used for floating point
+	  operations) if you don't have one. 486DX and Pentium processors have
+	  a math coprocessor built in, 486SX and 386 do not, unless you added
+	  a 487DX or 387, respectively. (The messages during boot time can
+	  give you some hints here ["man dmesg"].) Everyone needs either a
+	  coprocessor or this emulation.
+
+	  If you don't have a math coprocessor, you need to say Y here; if you
+	  say Y here even though you have a coprocessor, the coprocessor will
+	  be used nevertheless. (This behavior can be changed with the kernel
+	  command line option "no387", which comes handy if your coprocessor
+	  is broken. Try "man bootparam" or see the documentation of your boot
+	  loader (lilo or loadlin) about how to pass options to the kernel at
+	  boot time.) This means that it is a good idea to say Y here if you
+	  intend to use this kernel on different machines.
+
+	  More information about the internals of the Linux math coprocessor
+	  emulation can be found in <file:arch/x86/math-emu/README>.
+
+	  If you are not sure, say Y; apart from resulting in a 66 KB bigger
+	  kernel, it won't hurt.
+
+config MTRR
+	bool "MTRR (Memory Type Range Register) support"
+	---help---
+	  On Intel P6 family processors (Pentium Pro, Pentium II and later)
+	  the Memory Type Range Registers (MTRRs) may be used to control
+	  processor access to memory ranges. This is most useful if you have
+	  a video (VGA) card on a PCI or AGP bus. Enabling write-combining
+	  allows bus write transfers to be combined into a larger transfer
+	  before bursting over the PCI/AGP bus. This can increase performance
+	  of image write operations 2.5 times or more. Saying Y here creates a
+	  /proc/mtrr file which may be used to manipulate your processor's
+	  MTRRs. Typically the X server should use this.
+
+	  This code has a reasonably generic interface so that similar
+	  control registers on other processors can be easily supported
+	  as well:
+
+	  The Cyrix 6x86, 6x86MX and M II processors have Address Range
+	  Registers (ARRs) which provide a similar functionality to MTRRs. For
+	  these, the ARRs are used to emulate the MTRRs.
+	  The AMD K6-2 (stepping 8 and above) and K6-3 processors have two
+	  MTRRs. The Centaur C6 (WinChip) has 8 MCRs, allowing
+	  write-combining. All of these processors are supported by this code
+	  and it makes sense to say Y here if you have one of them.
+
+	  Saying Y here also fixes a problem with buggy SMP BIOSes which only
+	  set the MTRRs for the boot CPU and not for the secondary CPUs. This
+	  can lead to all sorts of problems, so it's good to say Y here.
+
+	  You can safely say Y even if your machine doesn't have MTRRs, you'll
+	  just add about 9 KB to your kernel.
+
+	  See <file:Documentation/mtrr.txt> for more information.
+
+config EFI
+	bool "Boot from EFI support"
+	depends on ACPI
+	default n
+	---help---
+	This enables the kernel to boot on EFI platforms using
+	system configuration information passed to it from the firmware.
+	This also enables the kernel to use any EFI runtime services that are
+	available (such as the EFI variable services).
+
+	This option is only useful on systems that have EFI firmware
+	and will result in a kernel image that is ~8k larger.  In addition,
+	you must use the latest ELILO loader available at
+	<http://elilo.sourceforge.net> in order to take advantage of
+	kernel initialization using EFI information (neither GRUB nor LILO know
+	anything about EFI).  However, even with this option, the resultant
+	kernel should continue to boot on existing non-EFI platforms.
+
+config IRQBALANCE
+ 	bool "Enable kernel irq balancing"
+	depends on SMP && X86_IO_APIC
+	default y
+	help
+ 	  The default yes will allow the kernel to do irq load balancing.
+	  Saying no will keep the kernel from doing irq load balancing.
+
+# turning this on wastes a bunch of space.
+# Summit needs it only when NUMA is on
+config BOOT_IOREMAP
+	bool
+	depends on (((X86_SUMMIT || X86_GENERICARCH) && NUMA) || (X86 && EFI))
+	default y
+
+config SECCOMP
+	bool "Enable seccomp to safely compute untrusted bytecode"
+	depends on PROC_FS
+	default y
+	help
+	  This kernel feature is useful for number crunching applications
+	  that may need to compute untrusted bytecode during their
+	  execution. By using pipes or other transports made available to
+	  the process as file descriptors supporting the read/write
+	  syscalls, it's possible to isolate those applications in
+	  their own address space using seccomp. Once seccomp is
+	  enabled via /proc/<pid>/seccomp, it cannot be disabled
+	  and the task is only allowed to execute a few safe syscalls
+	  defined by each seccomp mode.
+
+	  If unsure, say Y. Only embedded should say N here.
+
+source kernel/Kconfig.hz
+
+config KEXEC
+	bool "kexec system call"
+	help
+	  kexec is a system call that implements the ability to shutdown your
+	  current kernel, and to start another kernel.  It is like a reboot
+	  but it is independent of the system firmware.   And like a reboot
+	  you can start any kernel with it, not just Linux.
+
+	  The name comes from the similarity to the exec system call.
+
+	  It is an ongoing process to be certain the hardware in a machine
+	  is properly shutdown, so do not be surprised if this code does not
+	  initially work for you.  It may help to enable device hotplugging
+	  support.  As of this writing the exact hardware interface is
+	  strongly in flux, so no good recommendation can be made.
+
+config CRASH_DUMP
+	bool "kernel crash dumps (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	depends on HIGHMEM
+	help
+	  Generate crash dump after being started by kexec.
+	  This should be normally only set in special crash dump kernels
+	  which are loaded in the main kernel with kexec-tools into
+	  a specially reserved region and then later executed after
+	  a crash by kdump/kexec. The crash dump kernel must be compiled
+	  to a memory address not used by the main kernel or BIOS using
+	  PHYSICAL_START, or it must be built as a relocatable image
+	  (CONFIG_RELOCATABLE=y).
+	  For more details see Documentation/kdump/kdump.txt
+
+config PHYSICAL_START
+	hex "Physical address where the kernel is loaded" if (EMBEDDED || CRASH_DUMP)
+	default "0x1000000" if X86_NUMAQ
+	default "0x100000"
+	help
+	  This gives the physical address where the kernel is loaded.
+
+	  If kernel is a not relocatable (CONFIG_RELOCATABLE=n) then
+	  bzImage will decompress itself to above physical address and
+	  run from there. Otherwise, bzImage will run from the address where
+	  it has been loaded by the boot loader and will ignore above physical
+	  address.
+
+	  In normal kdump cases one does not have to set/change this option
+	  as now bzImage can be compiled as a completely relocatable image
+	  (CONFIG_RELOCATABLE=y) and be used to load and run from a different
+	  address. This option is mainly useful for the folks who don't want
+	  to use a bzImage for capturing the crash dump and want to use a
+	  vmlinux instead. vmlinux is not relocatable hence a kernel needs
+	  to be specifically compiled to run from a specific memory area
+	  (normally a reserved region) and this option comes handy.
+
+	  So if you are using bzImage for capturing the crash dump, leave
+	  the value here unchanged to 0x100000 and set CONFIG_RELOCATABLE=y.
+	  Otherwise if you plan to use vmlinux for capturing the crash dump
+	  change this value to start of the reserved region (Typically 16MB
+	  0x1000000). In other words, it can be set based on the "X" value as
+	  specified in the "crashkernel=YM@XM" command line boot parameter
+	  passed to the panic-ed kernel. Typically this parameter is set as
+	  crashkernel=64M@16M. Please take a look at
+	  Documentation/kdump/kdump.txt for more details about crash dumps.
+
+	  Usage of bzImage for capturing the crash dump is recommended as
+	  one does not have to build two kernels. Same kernel can be used
+	  as production kernel and capture kernel. Above option should have
+	  gone away after relocatable bzImage support is introduced. But it
+	  is present because there are users out there who continue to use
+	  vmlinux for dump capture. This option should go away down the
+	  line.
+
+	  Don't change this unless you know what you are doing.
+
+config RELOCATABLE
+	bool "Build a relocatable kernel (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	help
+	  This builds a kernel image that retains relocation information
+	  so it can be loaded someplace besides the default 1MB.
+	  The relocations tend to make the kernel binary about 10% larger,
+	  but are discarded at runtime.
+
+	  One use is for the kexec on panic case where the recovery kernel
+	  must live at a different physical address than the primary
+	  kernel.
+
+config PHYSICAL_ALIGN
+	hex "Alignment value to which kernel should be aligned"
+	default "0x100000"
+	range 0x2000 0x400000
+	help
+	  This value puts the alignment restrictions on physical address
+ 	  where kernel is loaded and run from. Kernel is compiled for an
+ 	  address which meets above alignment restriction.
+
+ 	  If bootloader loads the kernel at a non-aligned address and
+ 	  CONFIG_RELOCATABLE is set, kernel will move itself to nearest
+ 	  address aligned to above value and run from there.
+
+ 	  If bootloader loads the kernel at a non-aligned address and
+ 	  CONFIG_RELOCATABLE is not set, kernel will ignore the run time
+ 	  load address and decompress itself to the address it has been
+ 	  compiled for and run from there. The address for which kernel is
+ 	  compiled already meets above alignment restrictions. Hence the
+ 	  end result is that kernel runs from a physical address meeting
+	  above alignment restrictions.
+
+	  Don't change this unless you know what you are doing.
+
+config HOTPLUG_CPU
+	bool "Support for suspend on SMP and hot-pluggable CPUs (EXPERIMENTAL)"
+	depends on SMP && HOTPLUG && EXPERIMENTAL && !X86_VOYAGER
+	---help---
+	  Say Y here to experiment with turning CPUs off and on, and to
+	  enable suspend on SMP systems. CPUs can be controlled through
+	  /sys/devices/system/cpu.
+
+config COMPAT_VDSO
+	bool "Compat VDSO support"
+	default y
+	help
+	  Map the VDSO to the predictable old-style address too.
+	---help---
+	  Say N here if you are running a sufficiently recent glibc
+	  version (2.3.3 or later), to remove the high-mapped
+	  VDSO mapping and to exclusively use the randomized VDSO.
+
+	  If unsure, say Y.
+
+endmenu
+
+config ARCH_ENABLE_MEMORY_HOTPLUG
+	def_bool y
+	depends on HIGHMEM
+
+menu "Power management options (ACPI, APM)"
+	depends on !X86_VOYAGER
+
+source kernel/power/Kconfig
+
+source "drivers/acpi/Kconfig"
+
+menuconfig APM
+	tristate "APM (Advanced Power Management) BIOS support"
+	depends on PM_SLEEP && !X86_VISWS
+	---help---
+	  APM is a BIOS specification for saving power using several different
+	  techniques. This is mostly useful for battery powered laptops with
+	  APM compliant BIOSes. If you say Y here, the system time will be
+	  reset after a RESUME operation, the /proc/apm device will provide
+	  battery status information, and user-space programs will receive
+	  notification of APM "events" (e.g. battery status change).
+
+	  If you select "Y" here, you can disable actual use of the APM
+	  BIOS by passing the "apm=off" option to the kernel at boot time.
+
+	  Note that the APM support is almost completely disabled for
+	  machines with more than one CPU.
+
+	  In order to use APM, you will need supporting software. For location
+	  and more information, read <file:Documentation/pm.txt> and the
+	  Battery Powered Linux mini-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  This driver does not spin down disk drives (see the hdparm(8)
+	  manpage ("man 8 hdparm") for that), and it doesn't turn off
+	  VESA-compliant "green" monitors.
+
+	  This driver does not support the TI 4000M TravelMate and the ACER
+	  486/DX4/75 because they don't have compliant BIOSes. Many "green"
+	  desktop machines also don't have compliant BIOSes, and this driver
+	  may cause those machines to panic during the boot phase.
+
+	  Generally, if you don't have a battery in your machine, there isn't
+	  much point in using this driver and you should say N. If you get
+	  random kernel OOPSes or reboots that don't seem to be related to
+	  anything, try disabling/enabling this option (or disabling/enabling
+	  APM in your BIOS).
+
+	  Some other things you should try when experiencing seemingly random,
+	  "weird" problems:
+
+	  1) make sure that you have enough swap space and that it is
+	  enabled.
+	  2) pass the "no-hlt" option to the kernel
+	  3) switch on floating point emulation in the kernel and pass
+	  the "no387" option to the kernel
+	  4) pass the "floppy=nodma" option to the kernel
+	  5) pass the "mem=4M" option to the kernel (thereby disabling
+	  all but the first 4 MB of RAM)
+	  6) make sure that the CPU is not over clocked.
+	  7) read the sig11 FAQ at <http://www.bitwizard.nl/sig11/>
+	  8) disable the cache from your BIOS settings
+	  9) install a fan for the video card or exchange video RAM
+	  10) install a better fan for the CPU
+	  11) exchange RAM chips
+	  12) exchange the motherboard.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called apm.
+
+if APM
+
+config APM_IGNORE_USER_SUSPEND
+	bool "Ignore USER SUSPEND"
+	help
+	  This option will ignore USER SUSPEND requests. On machines with a
+	  compliant APM BIOS, you want to say N. However, on the NEC Versa M
+	  series notebooks, it is necessary to say Y because of a BIOS bug.
+
+config APM_DO_ENABLE
+	bool "Enable PM at boot time"
+	---help---
+	  Enable APM features at boot time. From page 36 of the APM BIOS
+	  specification: "When disabled, the APM BIOS does not automatically
+	  power manage devices, enter the Standby State, enter the Suspend
+	  State, or take power saving steps in response to CPU Idle calls."
+	  This driver will make CPU Idle calls when Linux is idle (unless this
+	  feature is turned off -- see "Do CPU IDLE calls", below). This
+	  should always save battery power, but more complicated APM features
+	  will be dependent on your BIOS implementation. You may need to turn
+	  this option off if your computer hangs at boot time when using APM
+	  support, or if it beeps continuously instead of suspending. Turn
+	  this off if you have a NEC UltraLite Versa 33/C or a Toshiba
+	  T400CDT. This is off by default since most machines do fine without
+	  this feature.
+
+config APM_CPU_IDLE
+	bool "Make CPU Idle calls when idle"
+	help
+	  Enable calls to APM CPU Idle/CPU Busy inside the kernel's idle loop.
+	  On some machines, this can activate improved power savings, such as
+	  a slowed CPU clock rate, when the machine is idle. These idle calls
+	  are made after the idle loop has run for some length of time (e.g.,
+	  333 mS). On some machines, this will cause a hang at boot time or
+	  whenever the CPU becomes idle. (On machines with more than one CPU,
+	  this option does nothing.)
+
+config APM_DISPLAY_BLANK
+	bool "Enable console blanking using APM"
+	help
+	  Enable console blanking using the APM. Some laptops can use this to
+	  turn off the LCD backlight when the screen blanker of the Linux
+	  virtual console blanks the screen. Note that this is only used by
+	  the virtual console screen blanker, and won't turn off the backlight
+	  when using the X Window system. This also doesn't have anything to
+	  do with your VESA-compliant power-saving monitor. Further, this
+	  option doesn't work for all laptops -- it might not turn off your
+	  backlight at all, or it might print a lot of errors to the console,
+	  especially if you are using gpm.
+
+config APM_ALLOW_INTS
+	bool "Allow interrupts during APM BIOS calls"
+	help
+	  Normally we disable external interrupts while we are making calls to
+	  the APM BIOS as a measure to lessen the effects of a badly behaving
+	  BIOS implementation.  The BIOS should reenable interrupts if it
+	  needs to.  Unfortunately, some BIOSes do not -- especially those in
+	  many of the newer IBM Thinkpads.  If you experience hangs when you
+	  suspend, try setting this to Y.  Otherwise, say N.
+
+config APM_REAL_MODE_POWER_OFF
+	bool "Use real mode APM BIOS call to power off"
+	help
+	  Use real mode APM BIOS calls to switch off the computer. This is
+	  a work-around for a number of buggy BIOSes. Switch this option on if
+	  your computer crashes instead of powering off properly.
+
+endif # APM
+
+source "arch/x86/kernel/cpu/cpufreq/Kconfig_32"
+
+source "drivers/cpuidle/Kconfig"
+
+endmenu
+
+menu "Bus options (PCI, PCMCIA, EISA, MCA, ISA)"
+
+config PCI
+	bool "PCI support" if !X86_VISWS
+	depends on !X86_VOYAGER
+	default y if X86_VISWS
+	select ARCH_SUPPORTS_MSI if (X86_LOCAL_APIC && X86_IO_APIC)
+	help
+	  Find out whether you have a PCI motherboard. PCI is the name of a
+	  bus system, i.e. the way the CPU talks to the other stuff inside
+	  your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
+	  VESA. If you have PCI, say Y, otherwise N.
+
+	  The PCI-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>, contains valuable
+	  information about which PCI hardware does work under Linux and which
+	  doesn't.
+
+choice
+	prompt "PCI access mode"
+	depends on PCI && !X86_VISWS
+	default PCI_GOANY
+	---help---
+	  On PCI systems, the BIOS can be used to detect the PCI devices and
+	  determine their configuration. However, some old PCI motherboards
+	  have BIOS bugs and may crash if this is done. Also, some embedded
+	  PCI-based systems don't have any BIOS at all. Linux can also try to
+	  detect the PCI hardware directly without using the BIOS.
+
+	  With this option, you can specify how Linux should detect the
+	  PCI devices. If you choose "BIOS", the BIOS will be used,
+	  if you choose "Direct", the BIOS won't be used, and if you
+	  choose "MMConfig", then PCI Express MMCONFIG will be used.
+	  If you choose "Any", the kernel will try MMCONFIG, then the
+	  direct access method and falls back to the BIOS if that doesn't
+	  work. If unsure, go with the default, which is "Any".
+
+config PCI_GOBIOS
+	bool "BIOS"
+
+config PCI_GOMMCONFIG
+	bool "MMConfig"
+
+config PCI_GODIRECT
+	bool "Direct"
+
+config PCI_GOANY
+	bool "Any"
+
+endchoice
+
+config PCI_BIOS
+	bool
+	depends on !X86_VISWS && PCI && (PCI_GOBIOS || PCI_GOANY)
+	default y
+
+config PCI_DIRECT
+	bool
+ 	depends on PCI && ((PCI_GODIRECT || PCI_GOANY) || X86_VISWS)
+	default y
+
+config PCI_MMCONFIG
+	bool
+	depends on PCI && ACPI && (PCI_GOMMCONFIG || PCI_GOANY)
+	default y
+
+config PCI_DOMAINS
+	bool
+	depends on PCI
+	default y
+
+source "drivers/pci/pcie/Kconfig"
+
+source "drivers/pci/Kconfig"
+
+config ISA_DMA_API
+	bool
+	default y
+
+config ISA
+	bool "ISA support"
+	depends on !(X86_VOYAGER || X86_VISWS)
+	help
+	  Find out whether you have ISA slots on your motherboard.  ISA is the
+	  name of a bus system, i.e. the way the CPU talks to the other stuff
+	  inside your box.  Other bus systems are PCI, EISA, MicroChannel
+	  (MCA) or VESA.  ISA is an older system, now being displaced by PCI;
+	  newer boards don't support it.  If you have ISA, say Y, otherwise N.
+
+config EISA
+	bool "EISA support"
+	depends on ISA
+	---help---
+	  The Extended Industry Standard Architecture (EISA) bus was
+	  developed as an open alternative to the IBM MicroChannel bus.
+
+	  The EISA bus provided some of the features of the IBM MicroChannel
+	  bus while maintaining backward compatibility with cards made for
+	  the older ISA bus.  The EISA bus saw limited use between 1988 and
+	  1995 when it was made obsolete by the PCI bus.
+
+	  Say Y here if you are building a kernel for an EISA-based machine.
+
+	  Otherwise, say N.
+
+source "drivers/eisa/Kconfig"
+
+config MCA
+	bool "MCA support" if !(X86_VISWS || X86_VOYAGER)
+	default y if X86_VOYAGER
+	help
+	  MicroChannel Architecture is found in some IBM PS/2 machines and
+	  laptops.  It is a bus system similar to PCI or ISA. See
+	  <file:Documentation/mca.txt> (and especially the web page given
+	  there) before attempting to build an MCA bus kernel.
+
+source "drivers/mca/Kconfig"
+
+config SCx200
+	tristate "NatSemi SCx200 support"
+	depends on !X86_VOYAGER
+	help
+	  This provides basic support for National Semiconductor's
+	  (now AMD's) Geode processors.  The driver probes for the
+	  PCI-IDs of several on-chip devices, so its a good dependency
+	  for other scx200_* drivers.
+
+	  If compiled as a module, the driver is named scx200.
+
+config SCx200HR_TIMER
+	tristate "NatSemi SCx200 27MHz High-Resolution Timer Support"
+	depends on SCx200 && GENERIC_TIME
+	default y
+	help
+	  This driver provides a clocksource built upon the on-chip
+	  27MHz high-resolution timer.  Its also a workaround for
+	  NSC Geode SC-1100's buggy TSC, which loses time when the
+	  processor goes idle (as is done by the scheduler).  The
+	  other workaround is idle=poll boot option.
+
+config GEODE_MFGPT_TIMER
+	bool "Geode Multi-Function General Purpose Timer (MFGPT) events"
+	depends on MGEODE_LX && GENERIC_TIME && GENERIC_CLOCKEVENTS
+	default y
+	help
+	  This driver provides a clock event source based on the MFGPT
+	  timer(s) in the CS5535 and CS5536 companion chip for the geode.
+	  MFGPTs have a better resolution and max interval than the
+	  generic PIT, and are suitable for use as high-res timers.
+
+config K8_NB
+	def_bool y
+	depends on AGP_AMD64
+
+source "drivers/pcmcia/Kconfig"
+
+source "drivers/pci/hotplug/Kconfig"
+
+endmenu
+
+menu "Executable file formats"
+
+source "fs/Kconfig.binfmt"
+
+endmenu
+
+source "net/Kconfig"
+
+source "drivers/Kconfig"
+
+source "fs/Kconfig"
+
+source "kernel/Kconfig.instrumentation"
+
+source "arch/x86/Kconfig.debug"
+
+source "security/Kconfig"
+
+source "crypto/Kconfig"
+
+source "lib/Kconfig"
+
+#
+# Use the generic interrupt handling code in kernel/irq/:
+#
+config GENERIC_HARDIRQS
+	bool
+	default y
+
+config GENERIC_IRQ_PROBE
+	bool
+	default y
+
+config GENERIC_PENDING_IRQ
+	bool
+	depends on GENERIC_HARDIRQS && SMP
+	default y
+
+config X86_SMP
+	bool
+	depends on SMP && !X86_VOYAGER
+	default y
+
+config X86_HT
+	bool
+	depends on SMP && !(X86_VISWS || X86_VOYAGER)
+	default y
+
+config X86_BIOS_REBOOT
+	bool
+	depends on !(X86_VISWS || X86_VOYAGER)
+	default y
+
+config X86_TRAMPOLINE
+	bool
+	depends on X86_SMP || (X86_VOYAGER && SMP)
+	default y
+
+config KTIME_SCALAR
+	bool
+	default y
diff --git a/arch/x86/Kconfig.x86_64 b/arch/x86/Kconfig.x86_64
new file mode 100644
index 00000000000..e2542e5b536
--- /dev/null
+++ b/arch/x86/Kconfig.x86_64
@@ -0,0 +1,844 @@
+#
+# For a description of the syntax of this configuration file,
+# see Documentation/kbuild/kconfig-language.txt.
+#
+# Note: ISA is disabled and will hopefully never be enabled.
+# If you managed to buy an ISA x86-64 box you'll have to fix all the
+# ISA drivers you need yourself.
+#
+
+mainmenu "Linux Kernel Configuration"
+
+config X86_64
+	bool
+	default y
+	help
+	  Port to the x86-64 architecture. x86-64 is a 64-bit extension to the
+	  classical 32-bit x86 architecture. For details see
+	  <http://www.x86-64.org/>.
+
+config 64BIT
+	def_bool y
+
+config X86
+	bool
+	default y
+
+config GENERIC_TIME
+	bool
+	default y
+
+config GENERIC_TIME_VSYSCALL
+	bool
+	default y
+
+config GENERIC_CMOS_UPDATE
+	bool
+	default y
+
+config CLOCKSOURCE_WATCHDOG
+	bool
+	default y
+
+config GENERIC_CLOCKEVENTS
+	bool
+	default y
+
+config GENERIC_CLOCKEVENTS_BROADCAST
+	bool
+	default y
+
+config ZONE_DMA32
+	bool
+	default y
+
+config LOCKDEP_SUPPORT
+	bool
+	default y
+
+config STACKTRACE_SUPPORT
+	bool
+	default y
+
+config SEMAPHORE_SLEEPERS
+	bool
+	default y
+
+config MMU
+	bool
+	default y
+
+config ZONE_DMA
+	bool
+	default y
+
+config ISA
+	bool
+
+config SBUS
+	bool
+
+config RWSEM_GENERIC_SPINLOCK
+	bool
+	default y
+
+config RWSEM_XCHGADD_ALGORITHM
+	bool
+
+config GENERIC_HWEIGHT
+	bool
+	default y
+
+config GENERIC_CALIBRATE_DELAY
+	bool
+	default y
+
+config X86_CMPXCHG
+	bool
+	default y
+
+config EARLY_PRINTK
+	bool
+	default y
+
+config GENERIC_ISA_DMA
+	bool
+	default y
+
+config GENERIC_IOMAP
+	bool
+	default y
+
+config ARCH_MAY_HAVE_PC_FDC
+	bool
+	default y
+
+config ARCH_POPULATES_NODE_MAP
+	def_bool y
+
+config DMI
+	bool
+	default y
+
+config AUDIT_ARCH
+	bool
+	default y
+
+config GENERIC_BUG
+	bool
+	default y
+	depends on BUG
+
+config ARCH_HAS_ILOG2_U32
+	bool
+	default n
+
+config ARCH_HAS_ILOG2_U64
+	bool
+	default n
+
+source "init/Kconfig"
+
+
+menu "Processor type and features"
+
+source "kernel/time/Kconfig"
+
+choice
+	prompt "Subarchitecture Type"
+	default X86_PC
+
+config X86_PC
+	bool "PC-compatible"
+	help
+	  Choose this option if your computer is a standard PC or compatible.
+
+config X86_VSMP
+	bool "Support for ScaleMP vSMP"
+	depends on PCI
+	 help
+	  Support for ScaleMP vSMP systems.  Say 'Y' here if this kernel is
+	  supposed to run on these EM64T-based machines.  Only choose this option
+	  if you have one of these machines.
+
+endchoice
+
+choice
+	prompt "Processor family"
+	default GENERIC_CPU
+
+config MK8
+	bool "AMD-Opteron/Athlon64"
+	help
+	  Optimize for AMD Opteron/Athlon64/Hammer/K8 CPUs.
+
+config MPSC
+       bool "Intel P4 / older Netburst based Xeon"
+       help
+	  Optimize for Intel Pentium 4, Pentium D and older Nocona/Dempsey
+	  Xeon CPUs with Intel 64bit which is compatible with x86-64.
+	  Note that the latest Xeons (Xeon 51xx and 53xx) are not based on the
+          Netburst core and shouldn't use this option. You can distinguish them
+	  using the cpu family field
+	  in /proc/cpuinfo. Family 15 is an older Xeon, Family 6 a newer one.
+
+config MCORE2
+	bool "Intel Core2 / newer Xeon"
+	help
+	  Optimize for Intel Core2 and newer Xeons (51xx)
+	  You can distinguish the newer Xeons from the older ones using
+	  the cpu family field in /proc/cpuinfo. 15 is an older Xeon
+	  (use CONFIG_MPSC then), 6 is a newer one.
+
+config GENERIC_CPU
+	bool "Generic-x86-64"
+	help
+	  Generic x86-64 CPU.
+	  Run equally well on all x86-64 CPUs.
+
+endchoice
+
+#
+# Define implied options from the CPU selection here
+#
+config X86_L1_CACHE_BYTES
+	int
+	default "128" if GENERIC_CPU || MPSC
+	default "64" if MK8 || MCORE2
+
+config X86_L1_CACHE_SHIFT
+	int
+	default "7" if GENERIC_CPU || MPSC
+	default "6" if MK8 || MCORE2
+
+config X86_INTERNODE_CACHE_BYTES
+	int
+	default "4096" if X86_VSMP
+	default X86_L1_CACHE_BYTES if !X86_VSMP
+
+config X86_TSC
+	bool
+	default y
+
+config X86_GOOD_APIC
+	bool
+	default y
+
+config MICROCODE
+	tristate "/dev/cpu/microcode - Intel CPU microcode support"
+	select FW_LOADER
+	---help---
+	  If you say Y here the 'File systems' section, you will be
+	  able to update the microcode on Intel processors. You will
+	  obviously need the actual microcode binary data itself which is
+	  not shipped with the Linux kernel.
+
+	  For latest news and information on obtaining all the required
+	  ingredients for this driver, check:
+	  <http://www.urbanmyth.org/microcode/>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called microcode.
+	  If you use modprobe or kmod you may also want to add the line
+	  'alias char-major-10-184 microcode' to your /etc/modules.conf file.
+
+config MICROCODE_OLD_INTERFACE
+	bool
+	depends on MICROCODE
+	default y
+
+config X86_MSR
+	tristate "/dev/cpu/*/msr - Model-specific register support"
+	help
+	  This device gives privileged processes access to the x86
+	  Model-Specific Registers (MSRs).  It is a character device with
+	  major 202 and minors 0 to 31 for /dev/cpu/0/msr to /dev/cpu/31/msr.
+	  MSR accesses are directed to a specific CPU on multi-processor
+	  systems.
+
+config X86_CPUID
+	tristate "/dev/cpu/*/cpuid - CPU information support"
+	help
+	  This device gives processes access to the x86 CPUID instruction to
+	  be executed on a specific processor.  It is a character device
+	  with major 203 and minors 0 to 31 for /dev/cpu/0/cpuid to
+	  /dev/cpu/31/cpuid.
+
+config X86_HT
+	bool
+	depends on SMP && !MK8
+	default y
+
+config MATH_EMULATION
+	bool
+
+config MCA
+	bool
+
+config EISA
+	bool
+
+config X86_IO_APIC
+	bool
+	default y
+
+config X86_LOCAL_APIC
+	bool
+	default y
+
+config MTRR
+	bool "MTRR (Memory Type Range Register) support"
+	---help---
+	  On Intel P6 family processors (Pentium Pro, Pentium II and later)
+	  the Memory Type Range Registers (MTRRs) may be used to control
+	  processor access to memory ranges. This is most useful if you have
+	  a video (VGA) card on a PCI or AGP bus. Enabling write-combining
+	  allows bus write transfers to be combined into a larger transfer
+	  before bursting over the PCI/AGP bus. This can increase performance
+	  of image write operations 2.5 times or more. Saying Y here creates a
+	  /proc/mtrr file which may be used to manipulate your processor's
+	  MTRRs. Typically the X server should use this.
+
+	  This code has a reasonably generic interface so that similar
+	  control registers on other processors can be easily supported
+	  as well.
+
+	  Saying Y here also fixes a problem with buggy SMP BIOSes which only
+	  set the MTRRs for the boot CPU and not for the secondary CPUs. This
+	  can lead to all sorts of problems, so it's good to say Y here.
+
+	  Just say Y here, all x86-64 machines support MTRRs.
+
+	  See <file:Documentation/mtrr.txt> for more information.
+
+config SMP
+	bool "Symmetric multi-processing support"
+	---help---
+	  This enables support for systems with more than one CPU. If you have
+	  a system with only one CPU, like most personal computers, say N. If
+	  you have a system with more than one CPU, say Y.
+
+	  If you say N here, the kernel will run on single and multiprocessor
+	  machines, but will use only one CPU of a multiprocessor machine. If
+	  you say Y here, the kernel will run on many, but not all,
+	  singleprocessor machines. On a singleprocessor machine, the kernel
+	  will run faster if you say N here.
+
+	  If you don't know what to do here, say N.
+
+config SCHED_SMT
+	bool "SMT (Hyperthreading) scheduler support"
+	depends on SMP
+	default n
+	help
+	  SMT scheduler support improves the CPU scheduler's decision making
+	  when dealing with Intel Pentium 4 chips with HyperThreading at a
+	  cost of slightly increased overhead in some places. If unsure say
+	  N here.
+
+config SCHED_MC
+	bool "Multi-core scheduler support"
+	depends on SMP
+	default y
+	help
+	  Multi-core scheduler support improves the CPU scheduler's decision
+	  making when dealing with multi-core CPU chips at a cost of slightly
+	  increased overhead in some places. If unsure say N here.
+
+source "kernel/Kconfig.preempt"
+
+config NUMA
+       bool "Non Uniform Memory Access (NUMA) Support"
+       depends on SMP
+       help
+	 Enable NUMA (Non Uniform Memory Access) support. The kernel 
+	 will try to allocate memory used by a CPU on the local memory 
+	 controller of the CPU and add some more NUMA awareness to the kernel.
+	 This code is recommended on all multiprocessor Opteron systems.
+	 If the system is EM64T, you should say N unless your system is EM64T 
+	 NUMA. 
+
+config K8_NUMA
+       bool "Old style AMD Opteron NUMA detection"
+       depends on NUMA && PCI
+       default y
+       help
+	 Enable K8 NUMA node topology detection.  You should say Y here if
+	 you have a multi processor AMD K8 system. This uses an old
+	 method to read the NUMA configuration directly from the builtin
+	 Northbridge of Opteron. It is recommended to use X86_64_ACPI_NUMA
+	 instead, which also takes priority if both are compiled in.   
+
+config NODES_SHIFT
+	int
+	default "6"
+	depends on NEED_MULTIPLE_NODES
+
+# Dummy CONFIG option to select ACPI_NUMA from drivers/acpi/Kconfig.
+
+config X86_64_ACPI_NUMA
+       bool "ACPI NUMA detection"
+       depends on NUMA
+       select ACPI 
+	select PCI
+       select ACPI_NUMA
+       default y
+       help
+	 Enable ACPI SRAT based node topology detection.
+
+config NUMA_EMU
+	bool "NUMA emulation"
+	depends on NUMA
+	help
+	  Enable NUMA emulation. A flat machine will be split
+	  into virtual nodes when booted with "numa=fake=N", where N is the
+	  number of nodes. This is only useful for debugging.
+
+config ARCH_DISCONTIGMEM_ENABLE
+       bool
+       depends on NUMA
+       default y
+
+config ARCH_DISCONTIGMEM_DEFAULT
+	def_bool y
+	depends on NUMA
+
+config ARCH_SPARSEMEM_ENABLE
+	def_bool y
+	depends on (NUMA || EXPERIMENTAL)
+	select SPARSEMEM_VMEMMAP_ENABLE
+
+config ARCH_MEMORY_PROBE
+	def_bool y
+	depends on MEMORY_HOTPLUG
+
+config ARCH_FLATMEM_ENABLE
+	def_bool y
+	depends on !NUMA
+
+source "mm/Kconfig"
+
+config MEMORY_HOTPLUG_RESERVE
+	def_bool y
+	depends on (MEMORY_HOTPLUG && DISCONTIGMEM)
+
+config HAVE_ARCH_EARLY_PFN_TO_NID
+	def_bool y
+	depends on NUMA
+
+config OUT_OF_LINE_PFN_TO_PAGE
+	def_bool y
+	depends on DISCONTIGMEM
+
+config NR_CPUS
+	int "Maximum number of CPUs (2-255)"
+	range 2 255
+	depends on SMP
+	default "8"
+	help
+	  This allows you to specify the maximum number of CPUs which this
+	  kernel will support. Current maximum is 255 CPUs due to
+	  APIC addressing limits. Less depending on the hardware.
+
+	  This is purely to save memory - each supported CPU requires
+	  memory in the static kernel configuration.
+
+config PHYSICAL_ALIGN
+	hex
+	default "0x200000"
+
+config HOTPLUG_CPU
+	bool "Support for suspend on SMP and hot-pluggable CPUs (EXPERIMENTAL)"
+	depends on SMP && HOTPLUG && EXPERIMENTAL
+	help
+		Say Y here to experiment with turning CPUs off and on.  CPUs
+		can be controlled through /sys/devices/system/cpu/cpu#.
+		This is also required for suspend/hibernation on SMP systems.
+
+		Say N if you want to disable CPU hotplug and don't need to
+		suspend.
+
+config ARCH_ENABLE_MEMORY_HOTPLUG
+	def_bool y
+
+config HPET_TIMER
+	bool
+	default y
+	help
+	  Use the IA-PC HPET (High Precision Event Timer) to manage
+	  time in preference to the PIT and RTC, if a HPET is
+	  present.  The HPET provides a stable time base on SMP
+	  systems, unlike the TSC, but it is more expensive to access,
+	  as it is off-chip.  You can find the HPET spec at
+	  <http://www.intel.com/hardwaredesign/hpetspec.htm>.
+
+config HPET_EMULATE_RTC
+	bool
+	depends on HPET_TIMER && RTC=y
+	default y
+
+# Mark as embedded because too many people got it wrong.
+# The code disables itself when not needed.
+config IOMMU
+	bool "IOMMU support" if EMBEDDED
+	default y
+	select SWIOTLB
+	select AGP
+	depends on PCI
+	help
+	  Support for full DMA access of devices with 32bit memory access only
+	  on systems with more than 3GB. This is usually needed for USB,
+	  sound, many IDE/SATA chipsets and some other devices.
+	  Provides a driver for the AMD Athlon64/Opteron/Turion/Sempron GART
+	  based hardware IOMMU and a software bounce buffer based IOMMU used
+	  on Intel systems and as fallback.
+	  The code is only active when needed (enough memory and limited
+	  device) unless CONFIG_IOMMU_DEBUG or iommu=force is specified
+	  too.
+
+config CALGARY_IOMMU
+	bool "IBM Calgary IOMMU support"
+	select SWIOTLB
+	depends on PCI && EXPERIMENTAL
+	help
+	  Support for hardware IOMMUs in IBM's xSeries x366 and x460
+	  systems. Needed to run systems with more than 3GB of memory
+	  properly with 32-bit PCI devices that do not support DAC
+	  (Double Address Cycle). Calgary also supports bus level
+	  isolation, where all DMAs pass through the IOMMU.  This
+	  prevents them from going anywhere except their intended
+	  destination. This catches hard-to-find kernel bugs and
+	  mis-behaving drivers and devices that do not use the DMA-API
+	  properly to set up their DMA buffers.  The IOMMU can be
+	  turned off at boot time with the iommu=off parameter.
+	  Normally the kernel will make the right choice by itself.
+	  If unsure, say Y.
+
+config CALGARY_IOMMU_ENABLED_BY_DEFAULT
+	bool "Should Calgary be enabled by default?"
+	default y
+	depends on CALGARY_IOMMU
+	help
+	  Should Calgary be enabled by default? if you choose 'y', Calgary
+	  will be used (if it exists). If you choose 'n', Calgary will not be
+	  used even if it exists. If you choose 'n' and would like to use
+	  Calgary anyway, pass 'iommu=calgary' on the kernel command line.
+	  If unsure, say Y.
+
+# need this always selected by IOMMU for the VIA workaround
+config SWIOTLB
+	bool
+	help
+	  Support for software bounce buffers used on x86-64 systems
+	  which don't have a hardware IOMMU (e.g. the current generation
+	  of Intel's x86-64 CPUs). Using this PCI devices which can only
+	  access 32-bits of memory can be used on systems with more than
+	  3 GB of memory. If unsure, say Y.
+
+config X86_MCE
+	bool "Machine check support" if EMBEDDED
+	default y
+	help
+	   Include a machine check error handler to report hardware errors.
+	   This version will require the mcelog utility to decode some
+	   machine check error logs. See
+	   ftp://ftp.x86-64.org/pub/linux/tools/mcelog
+
+config X86_MCE_INTEL
+	bool "Intel MCE features"
+	depends on X86_MCE && X86_LOCAL_APIC
+	default y
+	help
+	   Additional support for intel specific MCE features such as
+	   the thermal monitor.
+
+config X86_MCE_AMD
+	bool "AMD MCE features"
+	depends on X86_MCE && X86_LOCAL_APIC
+	default y
+	help
+	   Additional support for AMD specific MCE features such as
+	   the DRAM Error Threshold.
+
+config KEXEC
+	bool "kexec system call"
+	help
+	  kexec is a system call that implements the ability to shutdown your
+	  current kernel, and to start another kernel.  It is like a reboot
+	  but it is independent of the system firmware.   And like a reboot
+	  you can start any kernel with it, not just Linux.
+
+	  The name comes from the similarity to the exec system call.
+
+	  It is an ongoing process to be certain the hardware in a machine
+	  is properly shutdown, so do not be surprised if this code does not
+	  initially work for you.  It may help to enable device hotplugging
+	  support.  As of this writing the exact hardware interface is
+	  strongly in flux, so no good recommendation can be made.
+
+config CRASH_DUMP
+	bool "kernel crash dumps (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	help
+	  Generate crash dump after being started by kexec.
+	  This should be normally only set in special crash dump kernels
+	  which are loaded in the main kernel with kexec-tools into
+	  a specially reserved region and then later executed after
+	  a crash by kdump/kexec. The crash dump kernel must be compiled
+	  to a memory address not used by the main kernel or BIOS using
+	  PHYSICAL_START, or it must be built as a relocatable image
+	  (CONFIG_RELOCATABLE=y).
+	  For more details see Documentation/kdump/kdump.txt
+
+config RELOCATABLE
+	bool "Build a relocatable kernel (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	help
+	  Builds a relocatable kernel. This enables loading and running
+	  a kernel binary from a different physical address than it has
+	  been compiled for.
+
+	  One use is for the kexec on panic case where the recovery kernel
+	  must live at a different physical address than the primary
+	  kernel.
+
+	  Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
+	  it has been loaded at and the compile time physical address
+	  (CONFIG_PHYSICAL_START) is ignored.
+
+config PHYSICAL_START
+	hex "Physical address where the kernel is loaded" if (EMBEDDED || CRASH_DUMP)
+	default "0x200000"
+	help
+	  This gives the physical address where the kernel is loaded. It
+	  should be aligned to 2MB boundary.
+
+	  If kernel is a not relocatable (CONFIG_RELOCATABLE=n) then
+	  bzImage will decompress itself to above physical address and
+	  run from there. Otherwise, bzImage will run from the address where
+	  it has been loaded by the boot loader and will ignore above physical
+	  address.
+
+	  In normal kdump cases one does not have to set/change this option
+	  as now bzImage can be compiled as a completely relocatable image
+	  (CONFIG_RELOCATABLE=y) and be used to load and run from a different
+	  address. This option is mainly useful for the folks who don't want
+	  to use a bzImage for capturing the crash dump and want to use a
+	  vmlinux instead.
+
+	  So if you are using bzImage for capturing the crash dump, leave
+	  the value here unchanged to 0x200000 and set CONFIG_RELOCATABLE=y.
+	  Otherwise if you plan to use vmlinux for capturing the crash dump
+	  change this value to start of the reserved region (Typically 16MB
+	  0x1000000). In other words, it can be set based on the "X" value as
+	  specified in the "crashkernel=YM@XM" command line boot parameter
+	  passed to the panic-ed kernel. Typically this parameter is set as
+	  crashkernel=64M@16M. Please take a look at
+	  Documentation/kdump/kdump.txt for more details about crash dumps.
+
+	  Usage of bzImage for capturing the crash dump is advantageous as
+	  one does not have to build two kernels. Same kernel can be used
+	  as production kernel and capture kernel.
+
+	  Don't change this unless you know what you are doing.
+
+config SECCOMP
+	bool "Enable seccomp to safely compute untrusted bytecode"
+	depends on PROC_FS
+	default y
+	help
+	  This kernel feature is useful for number crunching applications
+	  that may need to compute untrusted bytecode during their
+	  execution. By using pipes or other transports made available to
+	  the process as file descriptors supporting the read/write
+	  syscalls, it's possible to isolate those applications in
+	  their own address space using seccomp. Once seccomp is
+	  enabled via /proc/<pid>/seccomp, it cannot be disabled
+	  and the task is only allowed to execute a few safe syscalls
+	  defined by each seccomp mode.
+
+	  If unsure, say Y. Only embedded should say N here.
+
+config CC_STACKPROTECTOR
+	bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	help
+         This option turns on the -fstack-protector GCC feature. This
+	  feature puts, at the beginning of critical functions, a canary
+	  value on the stack just before the return address, and validates
+	  the value just before actually returning.  Stack based buffer
+	  overflows (that need to overwrite this return address) now also
+	  overwrite the canary, which gets detected and the attack is then
+	  neutralized via a kernel panic.
+
+	  This feature requires gcc version 4.2 or above, or a distribution
+	  gcc with the feature backported. Older versions are automatically
+	  detected and for those versions, this configuration option is ignored.
+
+config CC_STACKPROTECTOR_ALL
+	bool "Use stack-protector for all functions"
+	depends on CC_STACKPROTECTOR
+	help
+	  Normally, GCC only inserts the canary value protection for
+	  functions that use large-ish on-stack buffers. By enabling
+	  this option, GCC will be asked to do this for ALL functions.
+
+source kernel/Kconfig.hz
+
+config K8_NB
+	def_bool y
+	depends on AGP_AMD64 || IOMMU || (PCI && NUMA)
+
+endmenu
+
+#
+# Use the generic interrupt handling code in kernel/irq/:
+#
+config GENERIC_HARDIRQS
+	bool
+	default y
+
+config GENERIC_IRQ_PROBE
+	bool
+	default y
+
+# we have no ISA slots, but we do have ISA-style DMA.
+config ISA_DMA_API
+	bool
+	default y
+
+config GENERIC_PENDING_IRQ
+	bool
+	depends on GENERIC_HARDIRQS && SMP
+	default y
+
+menu "Power management options"
+
+source kernel/power/Kconfig
+
+config ARCH_HIBERNATION_HEADER
+	bool
+	depends on HIBERNATION
+	default y
+
+source "drivers/acpi/Kconfig"
+
+source "arch/x86/kernel/cpu/cpufreq/Kconfig_64"
+
+source "drivers/cpuidle/Kconfig"
+
+endmenu
+
+menu "Bus options (PCI etc.)"
+
+config PCI
+	bool "PCI support"
+	select ARCH_SUPPORTS_MSI if (X86_LOCAL_APIC && X86_IO_APIC)
+
+# x86-64 doesn't support PCI BIOS access from long mode so always go direct.
+config PCI_DIRECT
+	bool
+	depends on PCI
+	default y
+
+config PCI_MMCONFIG
+	bool "Support mmconfig PCI config space access"
+	depends on PCI && ACPI
+
+config PCI_DOMAINS
+	bool
+	depends on PCI
+	default y
+
+config DMAR
+	bool "Support for DMA Remapping Devices (EXPERIMENTAL)"
+	depends on PCI_MSI && ACPI && EXPERIMENTAL
+	default y
+	help
+	  DMA remapping (DMAR) devices support enables independent address
+	  translations for Direct Memory Access (DMA) from devices.
+	  These DMA remapping devices are reported via ACPI tables
+	  and include PCI device scope covered by these DMA
+	  remapping devices.
+
+config DMAR_GFX_WA
+	bool "Support for Graphics workaround"
+	depends on DMAR
+	default y
+	help
+	 Current Graphics drivers tend to use physical address
+	 for DMA and avoid using DMA APIs. Setting this config
+	 option permits the IOMMU driver to set a unity map for
+	 all the OS-visible memory. Hence the driver can continue
+	 to use physical addresses for DMA.
+
+config DMAR_FLOPPY_WA
+	bool
+	depends on DMAR
+	default y
+	help
+	 Floppy disk drivers are know to bypass DMA API calls
+	 thereby failing to work when IOMMU is enabled. This
+	 workaround will setup a 1:1 mapping for the first
+	 16M to make floppy (an ISA device) work.
+
+source "drivers/pci/pcie/Kconfig"
+
+source "drivers/pci/Kconfig"
+
+source "drivers/pcmcia/Kconfig"
+
+source "drivers/pci/hotplug/Kconfig"
+
+endmenu
+
+
+menu "Executable file formats / Emulations"
+
+source "fs/Kconfig.binfmt"
+
+config IA32_EMULATION
+	bool "IA32 Emulation"
+	help
+	  Include code to run 32-bit programs under a 64-bit kernel. You should
+	  likely turn this on, unless you're 100% sure that you don't have any
+	  32-bit programs left.
+
+config IA32_AOUT
+       tristate "IA32 a.out support"
+       depends on IA32_EMULATION
+       help
+         Support old a.out binaries in the 32bit emulation.
+
+config COMPAT
+	bool
+	depends on IA32_EMULATION
+	default y
+
+config COMPAT_FOR_U64_ALIGNMENT
+	def_bool COMPAT
+
+config SYSVIPC_COMPAT
+	bool
+	depends on COMPAT && SYSVIPC
+	default y
+
+endmenu
+
+source "net/Kconfig"
+
+source drivers/Kconfig
+
+source "drivers/firmware/Kconfig"
+
+source fs/Kconfig
+
+source "kernel/Kconfig.instrumentation"
+
+source "arch/x86/Kconfig.debug"
+
+source "security/Kconfig"
+
+source "crypto/Kconfig"
+
+source "lib/Kconfig"