serial: Rework sh-sci for driver model.

sh-sci was turning in to an unmaintainable mess, especially with
regards to the port list. This cleans it up quite a bit, and
switches over to a platform device model where subtypes will
register their port list individually in their setup code.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

2 files changed, 467 insertions, 769 deletions

diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c
index cbede06cac2..f336ba6778d 100644
--- a/drivers/serial/sh-sci.c
+++ b/drivers/serial/sh-sci.c
@@ -3,7 +3,7 @@
  *
  * SuperH on-chip serial module support.  (SCI with no FIFO / with FIFO)
  *
- *  Copyright (C) 2002, 2003, 2004  Paul Mundt
+ *  Copyright (C) 2002 - 2006  Paul Mundt
  *
  * based off of the old drivers/char/sh-sci.c by:
  *
@@ -20,10 +20,9 @@
 
 #undef DEBUG
 
+#include <linux/config.h>
 #include <linux/module.h>
 #include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
 #include <linux/timer.h>
 #include <linux/interrupt.h>
 #include <linux/tty.h>
@@ -32,71 +31,77 @@
 #include <linux/major.h>
 #include <linux/string.h>
 #include <linux/sysrq.h>
-#include <linux/fcntl.h>
-#include <linux/ptrace.h>
 #include <linux/ioport.h>
 #include <linux/mm.h>
-#include <linux/slab.h>
 #include <linux/init.h>
 #include <linux/delay.h>
 #include <linux/console.h>
-#include <linux/bitops.h>
-#include <linux/generic_serial.h>
+#include <linux/platform_device.h>
 
 #ifdef CONFIG_CPU_FREQ
 #include <linux/notifier.h>
 #include <linux/cpufreq.h>
 #endif
 
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-
 #if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
 #include <asm/clock.h>
-#endif
-
-#ifdef CONFIG_SH_STANDARD_BIOS
 #include <asm/sh_bios.h>
+#include <asm/kgdb.h>
 #endif
 
+#include <asm/sci.h>
+
 #if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
 #define SUPPORT_SYSRQ
 #endif
 
 #include "sh-sci.h"
 
-#ifdef CONFIG_SH_KGDB
-#include <asm/kgdb.h>
+struct sci_port {
+	struct uart_port	port;
+
+	/* Port type */
+	unsigned int		type;
+
+	/* Port IRQs: ERI, RXI, TXI, BRI (optional) */
+	unsigned int		irqs[SCIx_NR_IRQS]; 
+
+	/* Port pin configuration */
+	void			(*init_pins)(struct uart_port *port,
+					     unsigned int cflag);
 
-static int kgdb_get_char(struct sci_port *port);
-static void kgdb_put_char(struct sci_port *port, char c);
-static void kgdb_handle_error(struct sci_port *port);
+	/* Port enable callback */
+	void			(*enable)(struct uart_port *port);
+
+	/* Port disable callback */
+	void			(*disable)(struct uart_port *port);
+
+	/* Break timer */
+	struct timer_list	break_timer;
+	int			break_flag;
+};
+
+#ifdef CONFIG_SH_KGDB
 static struct sci_port *kgdb_sci_port;
-#endif /* CONFIG_SH_KGDB */
+#endif
 
 #ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
-static struct sci_port *serial_console_port = 0;
-#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
+static struct sci_port *serial_console_port;
+#endif
 
 /* Function prototypes */
 static void sci_stop_tx(struct uart_port *port);
-static void sci_start_tx(struct uart_port *port);
-static void sci_start_rx(struct uart_port *port, unsigned int tty_start);
-static void sci_stop_rx(struct uart_port *port);
-static int sci_request_irq(struct sci_port *port);
-static void sci_free_irq(struct sci_port *port);
-
-static struct sci_port sci_ports[];
-static struct uart_driver sci_uart_driver;
 
-#define SCI_NPORTS sci_uart_driver.nr
+#define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS
 
-#if defined(CONFIG_SH_STANDARD_BIOS) || defined(CONFIG_SH_KGDB)
+static struct sci_port sci_ports[SCI_NPORTS];
+static struct uart_driver sci_uart_driver;
 
-static void handle_error(struct uart_port *port)
-{				/* Clear error flags */
+#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && \
+    defined(CONFIG_SH_STANDARD_BIOS) || defined(CONFIG_SH_KGDB)
+static inline void handle_error(struct uart_port *port)
+{
+	/* Clear error flags */
 	sci_out(port, SCxSR, SCxSR_ERROR_CLEAR(port));
 }
 
@@ -106,8 +111,8 @@ static int get_char(struct uart_port *port)
 	unsigned short status;
 	int c;
 
-	local_irq_save(flags);
-        do {
+	spin_lock_irqsave(&port->lock, flags);
+	do {
 		status = sci_in(port, SCxSR);
 		if (status & SCxSR_ERRORS(port)) {
 			handle_error(port);
@@ -117,38 +122,19 @@ static int get_char(struct uart_port *port)
 	c = sci_in(port, SCxRDR);
 	sci_in(port, SCxSR);            /* Dummy read */
 	sci_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
-	local_irq_restore(flags);
+	spin_unlock_irqrestore(&port->lock, flags);
 
 	return c;
 }
-
-/* Taken from sh-stub.c of GDB 4.18 */
-static const char hexchars[] = "0123456789abcdef";
-
-static __inline__ char highhex(int  x)
-{
-	return hexchars[(x >> 4) & 0xf];
-}
-
-static __inline__ char lowhex(int  x)
-{
-	return hexchars[x & 0xf];
-}
-
 #endif /* CONFIG_SH_STANDARD_BIOS || CONFIG_SH_KGDB */
 
-/*
- * Send the packet in buffer.  The host gets one chance to read it.
- * This routine does not wait for a positive acknowledge.
- */
-
-#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
+#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || defined(CONFIG_SH_KGDB)
 static void put_char(struct uart_port *port, char c)
 {
 	unsigned long flags;
 	unsigned short status;
 
-	local_irq_save(flags);
+	spin_lock_irqsave(&port->lock, flags);
 
 	do {
 		status = sci_in(port, SCxSR);
@@ -158,9 +144,11 @@ static void put_char(struct uart_port *port, char c)
 	sci_in(port, SCxSR);            /* Dummy read */
 	sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));
 
-	local_irq_restore(flags);
+	spin_unlock_irqrestore(&port->lock, flags);
 }
+#endif
 
+#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
 static void put_string(struct sci_port *sci_port, const char *buffer, int count)
 {
 	struct uart_port *port = &sci_port->port;
@@ -213,96 +201,28 @@ static void put_string(struct sci_port *sci_port, const char *buffer, int count)
 }
 #endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
 
-
 #ifdef CONFIG_SH_KGDB
-
-/* Is the SCI ready, ie is there a char waiting? */
-static int kgdb_is_char_ready(struct sci_port *port)
-{
-        unsigned short status = sci_in(port, SCxSR);
-
-        if (status & (SCxSR_ERRORS(port) | SCxSR_BRK(port)))
-                kgdb_handle_error(port);
-
-        return (status & SCxSR_RDxF(port));
-}
-
-/* Write a char */
-static void kgdb_put_char(struct sci_port *port, char c)
-{
-        unsigned short status;
-
-        do
-                status = sci_in(port, SCxSR);
-        while (!(status & SCxSR_TDxE(port)));
-
-        sci_out(port, SCxTDR, c);
-        sci_in(port, SCxSR);    /* Dummy read */
-        sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));
-}
-
-/* Get a char if there is one, else ret -1 */
-static int kgdb_get_char(struct sci_port *port)
-{
-        int c;
-
-        if (kgdb_is_char_ready(port) == 0)
-                c = -1;
-        else {
-                c = sci_in(port, SCxRDR);
-                sci_in(port, SCxSR);    /* Dummy read */
-                sci_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
-        }
-
-        return c;
-}
-
-/* Called from kgdbstub.c to get a character, i.e. is blocking */
 static int kgdb_sci_getchar(void)
 {
-        volatile int c;
+        int c;
 
         /* Keep trying to read a character, this could be neater */
-        while ((c = kgdb_get_char(kgdb_sci_port)) < 0);
+        while ((c = get_char(kgdb_sci_port)) < 0)
+		cpu_relax();
 
         return c;
 }
 
-/* Called from kgdbstub.c to put a character, just a wrapper */
-static void kgdb_sci_putchar(int c)
-{
-
-        kgdb_put_char(kgdb_sci_port, c);
-}
-
-/* Clear any errors on the SCI */
-static void kgdb_handle_error(struct sci_port *port)
+static inline void kgdb_sci_putchar(int c)
 {
-        sci_out(port, SCxSR, SCxSR_ERROR_CLEAR(port));  /* Clear error flags */
+        put_char(kgdb_sci_port, c);
 }
-
-/* Breakpoint if there's a break sent on the serial port */
-static void kgdb_break_interrupt(int irq, void *ptr, struct pt_regs *regs)
-{
-        struct sci_port *port = ptr;
-        unsigned short status = sci_in(port, SCxSR);
-
-        if (status & SCxSR_BRK(port)) {
-
-                /* Break into the debugger if a break is detected */
-                BREAKPOINT();
-
-                /* Clear */
-                sci_out(port, SCxSR, SCxSR_BREAK_CLEAR(port));
-        }
-}
-
 #endif /* CONFIG_SH_KGDB */
 
 #if defined(__H8300S__)
 enum { sci_disable, sci_enable };
 
-static void h8300_sci_enable(struct uart_port* port, unsigned int ctrl)
+static void h8300_sci_config(struct uart_port* port, unsigned int ctrl)
 {
 	volatile unsigned char *mstpcrl=(volatile unsigned char *)MSTPCRL;
 	int ch = (port->mapbase  - SMR0) >> 3;
@@ -314,32 +234,66 @@ static void h8300_sci_enable(struct uart_port* port, unsigned int ctrl)
 		*mstpcrl &= ~mask;
 	}
 }
+
+static inline void h8300_sci_enable(struct uart_port *port)
+{
+	h8300_sci_config(port, sci_enable);
+}
+
+static inline void h8300_sci_disable(struct uart_port *port)
+{
+	h8300_sci_config(port, sci_disable);
+}
 #endif
 
-#if defined(SCI_ONLY) || defined(SCI_AND_SCIF)
-#if defined(__H8300H__) || defined(__H8300S__)
+#if defined(SCI_ONLY) || defined(SCI_AND_SCIF) && \
+    defined(__H8300H__) || defined(__H8300S__)
 static void sci_init_pins_sci(struct uart_port* port, unsigned int cflag)
 {
 	int ch = (port->mapbase - SMR0) >> 3;
 
 	/* set DDR regs */
-	H8300_GPIO_DDR(h8300_sci_pins[ch].port,h8300_sci_pins[ch].rx,H8300_GPIO_INPUT);
-	H8300_GPIO_DDR(h8300_sci_pins[ch].port,h8300_sci_pins[ch].tx,H8300_GPIO_OUTPUT);
+	H8300_GPIO_DDR(h8300_sci_pins[ch].port,
+		       h8300_sci_pins[ch].rx,
+		       H8300_GPIO_INPUT);
+	H8300_GPIO_DDR(h8300_sci_pins[ch].port,
+		       h8300_sci_pins[ch].tx,
+		       H8300_GPIO_OUTPUT);
+
 	/* tx mark output*/
 	H8300_SCI_DR(ch) |= h8300_sci_pins[ch].tx;
 }
+#else
+#define sci_init_pins_sci NULL
+#endif
+
+#if defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
+static void sci_init_pins_irda(struct uart_port *port, unsigned int cflag)
+{
+	unsigned int fcr_val = 0;
+
+	if (cflag & CRTSCTS)
+		fcr_val |= SCFCR_MCE;
+
+	sci_out(port, SCFCR, fcr_val);
+}
+#else
+#define sci_init_pins_irda NULL
 #endif
+
+#ifdef SCI_ONLY
+#define sci_init_pins_scif NULL
 #endif
 
 #if defined(SCIF_ONLY) || defined(SCI_AND_SCIF)
-#if defined(CONFIG_CPU_SUBTYPE_SH7300)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7710)
 /* SH7300 doesn't use RTS/CTS */
 static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 {
 	sci_out(port, SCFCR, 0);
 }
 #elif defined(CONFIG_CPU_SH3)
-/* For SH7705, SH7707, SH7709, SH7709A, SH7729 */
+/* For SH7705, SH7706, SH7707, SH7709, SH7709A, SH7729 */
 static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 {
 	unsigned int fcr_val = 0;
@@ -366,20 +320,7 @@ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 
 	sci_out(port, SCFCR, fcr_val);
 }
-
-#if defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
-static void sci_init_pins_irda(struct uart_port *port, unsigned int cflag)
-{
-	unsigned int fcr_val = 0;
-
-	if (cflag & CRTSCTS)
-		fcr_val |= SCFCR_MCE;
-
-	sci_out(port, SCFCR, fcr_val);
-}
-#endif
 #else
-
 /* For SH7750 */
 static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 {
@@ -388,7 +329,9 @@ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 	if (cflag & CRTSCTS) {
 		fcr_val |= SCFCR_MCE;
 	} else {
-#ifdef CONFIG_CPU_SUBTYPE_SH7780
+#ifdef CONFIG_CPU_SUBTYPE_SH7343
+		/* Nothing */
+#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
 		ctrl_outw(0x0080, SCSPTR0); /* Set RTS = 1 */
 #else
 		ctrl_outw(0x0080, SCSPTR2); /* Set RTS = 1 */
@@ -396,10 +339,41 @@ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 	}
 	sci_out(port, SCFCR, fcr_val);
 }
+#endif
+
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+static inline int scif_txroom(struct uart_port *port)
+{
+	return SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0x7f);
+}
+
+static inline int scif_rxroom(struct uart_port *port)
+{
+	return sci_in(port, SCRFDR) & 0x7f;
+}
+#else
+static inline int scif_txroom(struct uart_port *port)
+{
+	return SCIF_TXROOM_MAX - (sci_in(port, SCFDR) >> 8);
+}
 
+static inline int scif_rxroom(struct uart_port *port)
+{
+	return sci_in(port, SCFDR) & SCIF_RFDC_MASK;
+}
 #endif
 #endif /* SCIF_ONLY || SCI_AND_SCIF */
 
+static inline int sci_txroom(struct uart_port *port)
+{
+	return ((sci_in(port, SCxSR) & SCI_TDRE) != 0);
+}
+
+static inline int sci_rxroom(struct uart_port *port)
+{
+	return ((sci_in(port, SCxSR) & SCxSR_RDxF(port)) != 0);
+}
+
 /* ********************************************************************** *
  *                   the interrupt related routines                       *
  * ********************************************************************** */
@@ -408,14 +382,12 @@ static void sci_transmit_chars(struct uart_port *port)
 {
 	struct circ_buf *xmit = &port->info->xmit;
 	unsigned int stopped = uart_tx_stopped(port);
-	unsigned long flags;
 	unsigned short status;
 	unsigned short ctrl;
-	int count, txroom;
+	int count;
 
 	status = sci_in(port, SCxSR);
 	if (!(status & SCxSR_TDxE(port))) {
-		local_irq_save(flags);
 		ctrl = sci_in(port, SCSCR);
 		if (uart_circ_empty(xmit)) {
 			ctrl &= ~SCI_CTRL_FLAGS_TIE;
@@ -423,25 +395,15 @@ static void sci_transmit_chars(struct uart_port *port)
 			ctrl |= SCI_CTRL_FLAGS_TIE;
 		}
 		sci_out(port, SCSCR, ctrl);
-		local_irq_restore(flags);
 		return;
 	}
 
-#if !defined(SCI_ONLY)
-	if (port->type == PORT_SCIF) {
-#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
-		txroom = SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0x7f);
-#else
-		txroom = SCIF_TXROOM_MAX - (sci_in(port, SCFDR)>>8);
-#endif
-	} else {
-		txroom = (sci_in(port, SCxSR) & SCI_TDRE)?1:0;
-	}
-#else
-	txroom = (sci_in(port, SCxSR) & SCI_TDRE)?1:0;
+#ifndef SCI_ONLY
+	if (port->type == PORT_SCIF)
+		count = scif_txroom(port);
+	else
 #endif
-
-	count = txroom;
+		count = sci_txroom(port);
 
 	do {
 		unsigned char c;
@@ -468,7 +430,6 @@ static void sci_transmit_chars(struct uart_port *port)
 	if (uart_circ_empty(xmit)) {
 		sci_stop_tx(port);
 	} else {
-		local_irq_save(flags);
 		ctrl = sci_in(port, SCSCR);
 
 #if !defined(SCI_ONLY)
@@ -480,7 +441,6 @@ static void sci_transmit_chars(struct uart_port *port)
 
 		ctrl |= SCI_CTRL_FLAGS_TIE;
 		sci_out(port, SCSCR, ctrl);
-		local_irq_restore(flags);
 	}
 }
 
@@ -490,6 +450,7 @@ static void sci_transmit_chars(struct uart_port *port)
 static inline void sci_receive_chars(struct uart_port *port,
 				     struct pt_regs *regs)
 {
+	struct sci_port *sci_port = (struct sci_port *)port;
 	struct tty_struct *tty = port->info->tty;
 	int i, count, copied = 0;
 	unsigned short status;
@@ -501,18 +462,11 @@ static inline void sci_receive_chars(struct uart_port *port,
 
 	while (1) {
 #if !defined(SCI_ONLY)
-		if (port->type == PORT_SCIF) {
-#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
-			count = sci_in(port, SCRFDR) & 0x7f;
-#else
-			count = sci_in(port, SCFDR)&SCIF_RFDC_MASK ;
-#endif
-		} else {
-			count = (sci_in(port, SCxSR)&SCxSR_RDxF(port))?1:0;
-		}
-#else
-		count = (sci_in(port, SCxSR)&SCxSR_RDxF(port))?1:0;
+		if (port->type == PORT_SCIF)
+			count = scif_rxroom(port);
+		else
 #endif
+			count = sci_rxroom(port);
 
 		/* Don't copy more bytes than there is room for in the buffer */
 		count = tty_buffer_request_room(tty, count);
@@ -523,11 +477,10 @@ static inline void sci_receive_chars(struct uart_port *port,
 
 		if (port->type == PORT_SCI) {
 			char c = sci_in(port, SCxRDR);
-                       if(((struct sci_port *)port)->break_flag
-			    || uart_handle_sysrq_char(port, c, regs)) {
+			if (uart_handle_sysrq_char(port, c, regs) || sci_port->break_flag)
 				count = 0;
-			} else {
-			    tty_insert_flip_char(tty, c, TTY_NORMAL);
+			else {
+				tty_insert_flip_char(tty, c, TTY_NORMAL);
 			}
 		} else {
 			for (i=0; i<count; i++) {
@@ -535,15 +488,17 @@ static inline void sci_receive_chars(struct uart_port *port,
 				status = sci_in(port, SCxSR);
 #if defined(CONFIG_CPU_SH3)
 				/* Skip "chars" during break */
-				if (((struct sci_port *)port)->break_flag) {
+				if (sci_port->break_flag) {
 					if ((c == 0) &&
 					    (status & SCxSR_FER(port))) {
 						count--; i--;
 						continue;
 					}
+
 					/* Nonzero => end-of-break */
 					pr_debug("scif: debounce<%02x>\n", c);
-					((struct sci_port *)port)->break_flag = 0;
+					sci_port->break_flag = 0;
+
 					if (STEPFN(c)) {
 						count--; i--;
 						continue;
@@ -600,15 +555,17 @@ static void sci_schedule_break_timer(struct sci_port *port)
 /* Ensure that two consecutive samples find the break over. */
 static void sci_break_timer(unsigned long data)
 {
-    struct sci_port * port = (struct sci_port *)data;
-	if(sci_rxd_in(&port->port) == 0) {
+	struct sci_port *port = (struct sci_port *)data;
+
+	if (sci_rxd_in(&port->port) == 0) {
 		port->break_flag = 1;
-	    sci_schedule_break_timer(port);
-	} else if(port->break_flag == 1){
+		sci_schedule_break_timer(port);
+	} else if (port->break_flag == 1) {
 		/* break is over. */
 		port->break_flag = 2;
-	    sci_schedule_break_timer(port);
-	} else port->break_flag = 0;
+		sci_schedule_break_timer(port);
+	} else
+		port->break_flag = 0;
 }
 
 static inline int sci_handle_errors(struct uart_port *port)
@@ -617,40 +574,41 @@ static inline int sci_handle_errors(struct uart_port *port)
 	unsigned short status = sci_in(port, SCxSR);
 	struct tty_struct *tty = port->info->tty;
 
-	if (status&SCxSR_ORER(port)) {
+	if (status & SCxSR_ORER(port)) {
 		/* overrun error */
-		if(tty_insert_flip_char(tty, 0, TTY_OVERRUN))
+		if (tty_insert_flip_char(tty, 0, TTY_OVERRUN))
 			copied++;
 		pr_debug("sci: overrun error\n");
 	}
 
-	if (status&SCxSR_FER(port)) {
+	if (status & SCxSR_FER(port)) {
 		if (sci_rxd_in(port) == 0) {
 			/* Notify of BREAK */
-			struct sci_port * sci_port = (struct sci_port *)port;
-			if(!sci_port->break_flag) {
-	                	sci_port->break_flag = 1;
-	                	sci_schedule_break_timer((struct sci_port *)port);
+			struct sci_port *sci_port = (struct sci_port *)port;
+
+			if (!sci_port->break_flag) {
+				sci_port->break_flag = 1;
+				sci_schedule_break_timer(sci_port);
+
 				/* Do sysrq handling. */
-				if(uart_handle_break(port))
+				if (uart_handle_break(port))
 					return 0;
 			        pr_debug("sci: BREAK detected\n");
-			        if(tty_insert_flip_char(tty, 0, TTY_BREAK))
+				if (tty_insert_flip_char(tty, 0, TTY_BREAK))
 				        copied++;
                        }
-		}
-		else {
+		} else {
 			/* frame error */
-			if(tty_insert_flip_char(tty, 0, TTY_FRAME))
+			if (tty_insert_flip_char(tty, 0, TTY_FRAME))
 				copied++;
 			pr_debug("sci: frame error\n");
 		}
 	}
 
-	if (status&SCxSR_PER(port)) {
-		if(tty_insert_flip_char(tty, 0, TTY_PARITY))
-			copied++;
+	if (status & SCxSR_PER(port)) {
 		/* parity error */
+		if (tty_insert_flip_char(tty, 0, TTY_PARITY))
+			copied++;
 		pr_debug("sci: parity error\n");
 	}
 
@@ -673,7 +631,7 @@ static inline int sci_handle_breaks(struct uart_port *port)
 		s->break_flag = 1;
 #endif
 		/* Notify of BREAK */
-		if(tty_insert_flip_char(tty, 0, TTY_BREAK))
+		if (tty_insert_flip_char(tty, 0, TTY_BREAK))
 			copied++;
 		pr_debug("sci: BREAK detected\n");
 	}
@@ -682,7 +640,7 @@ static inline int sci_handle_breaks(struct uart_port *port)
 	/* XXX: Handle SCIF overrun error */
 	if (port->type == PORT_SCIF && (sci_in(port, SCLSR) & SCIF_ORER) != 0) {
 		sci_out(port, SCLSR, 0);
-		if(tty_insert_flip_char(tty, 0, TTY_OVERRUN)) {
+		if (tty_insert_flip_char(tty, 0, TTY_OVERRUN)) {
 			copied++;
 			pr_debug("sci: overrun error\n");
 		}
@@ -691,13 +649,12 @@ static inline int sci_handle_breaks(struct uart_port *port)
 
 	if (copied)
 		tty_flip_buffer_push(tty);
+
 	return copied;
 }
 
-static irqreturn_t sci_rx_interrupt(int irq, void *ptr, struct pt_regs *regs)
+static irqreturn_t sci_rx_interrupt(int irq, void *port, struct pt_regs *regs)
 {
-	struct uart_port *port = ptr;
-
 	/* I think sci_receive_chars has to be called irrespective
 	 * of whether the I_IXOFF is set, otherwise, how is the interrupt
 	 * to be disabled?
@@ -711,7 +668,9 @@ static irqreturn_t sci_tx_interrupt(int irq, void *ptr, struct pt_regs *regs)
 {
 	struct uart_port *port = ptr;
 
+	spin_lock_irq(&port->lock);
 	sci_transmit_chars(port);
+	spin_unlock_irq(&port->lock);
 
 	return IRQ_HANDLED;
 }
@@ -755,6 +714,12 @@ static irqreturn_t sci_br_interrupt(int irq, void *ptr, struct pt_regs *regs)
 
 	/* Handle BREAKs */
 	sci_handle_breaks(port);
+
+#ifdef CONFIG_SH_KGDB
+	/* Break into the debugger if a break is detected */
+	BREAKPOINT();
+#endif
+
 	sci_out(port, SCxSR, SCxSR_BREAK_CLEAR(port));
 
 	return IRQ_HANDLED;
@@ -769,16 +734,16 @@ static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr, struct pt_regs *regs)
         scr_status = sci_in(port,SCSCR);
 
 	/* Tx Interrupt */
-        if ((ssr_status&0x0020) && (scr_status&0x0080))
+        if ((ssr_status & 0x0020) && (scr_status & 0x0080))
                 sci_tx_interrupt(irq, ptr, regs);
 	/* Rx Interrupt */
-        if ((ssr_status&0x0002) && (scr_status&0x0040))
+        if ((ssr_status & 0x0002) && (scr_status & 0x0040))
                 sci_rx_interrupt(irq, ptr, regs);
 	/* Error Interrupt */
-        if ((ssr_status&0x0080) && (scr_status&0x0400))
+        if ((ssr_status & 0x0080) && (scr_status & 0x0400))
                 sci_er_interrupt(irq, ptr, regs);
 	/* Break Interrupt */
-        if ((ssr_status&0x0010) && (scr_status&0x0200))
+        if ((ssr_status & 0x0010) && (scr_status & 0x0200))
                 sci_br_interrupt(irq, ptr, regs);
 
 	return IRQ_HANDLED;
@@ -789,7 +754,8 @@ static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr, struct pt_regs *regs)
  * Here we define a transistion notifier so that we can update all of our
  * ports' baud rate when the peripheral clock changes.
  */
-static int sci_notifier(struct notifier_block *self, unsigned long phase, void *p)
+static int sci_notifier(struct notifier_block *self,
+			unsigned long phase, void *p)
 {
 	struct cpufreq_freqs *freqs = p;
 	int i;
@@ -816,8 +782,9 @@ static int sci_notifier(struct notifier_block *self, unsigned long phase, void *
 			clk_put(clk);
 		}
 
-		printk("%s: got a postchange notification for cpu %d (old %d, new %d)\n",
-				__FUNCTION__, freqs->cpu, freqs->old, freqs->new);
+		printk(KERN_INFO "%s: got a postchange notification "
+		       "for cpu %d (old %d, new %d)\n",
+		       __FUNCTION__, freqs->cpu, freqs->old, freqs->new);
 	}
 
 	return NOTIFY_OK;
@@ -841,8 +808,9 @@ static int sci_request_irq(struct sci_port *port)
 			printk(KERN_ERR "sci: Cannot allocate irq.(IRQ=0)\n");
 			return -ENODEV;
 		}
-		if (request_irq(port->irqs[0], sci_mpxed_interrupt, IRQF_DISABLED,
-				"sci", port)) {
+
+		if (request_irq(port->irqs[0], sci_mpxed_interrupt,
+				SA_INTERRUPT, "sci", port)) {
 			printk(KERN_ERR "sci: Cannot allocate irq.\n");
 			return -ENODEV;
 		}
@@ -850,8 +818,8 @@ static int sci_request_irq(struct sci_port *port)
 		for (i = 0; i < ARRAY_SIZE(handlers); i++) {
 			if (!port->irqs[i])
 				continue;
-			if (request_irq(port->irqs[i], handlers[i], IRQF_DISABLED,
-					desc[i], port)) {
+			if (request_irq(port->irqs[i], handlers[i],
+					SA_INTERRUPT, desc[i], port)) {
 				printk(KERN_ERR "sci: Cannot allocate irq.\n");
 				return -ENODEV;
 			}
@@ -903,50 +871,42 @@ static unsigned int sci_get_mctrl(struct uart_port *port)
 
 static void sci_start_tx(struct uart_port *port)
 {
-	struct sci_port *s = &sci_ports[port->line];
+	unsigned short ctrl;
 
-	disable_irq(s->irqs[SCIx_TXI_IRQ]);
-	sci_transmit_chars(port);
-	enable_irq(s->irqs[SCIx_TXI_IRQ]);
+	/* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
+	ctrl = sci_in(port, SCSCR);
+	ctrl |= SCI_CTRL_FLAGS_TIE;
+	sci_out(port, SCSCR, ctrl);
 }
 
 static void sci_stop_tx(struct uart_port *port)
 {
-	unsigned long flags;
 	unsigned short ctrl;
 
 	/* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */
-	local_irq_save(flags);
 	ctrl = sci_in(port, SCSCR);
 	ctrl &= ~SCI_CTRL_FLAGS_TIE;
 	sci_out(port, SCSCR, ctrl);
-	local_irq_restore(flags);
 }
 
 static void sci_start_rx(struct uart_port *port, unsigned int tty_start)
 {
-	unsigned long flags;
 	unsigned short ctrl;
 
 	/* Set RIE (Receive Interrupt Enable) bit in SCSCR */
-	local_irq_save(flags);
 	ctrl = sci_in(port, SCSCR);
 	ctrl |= SCI_CTRL_FLAGS_RIE | SCI_CTRL_FLAGS_REIE;
 	sci_out(port, SCSCR, ctrl);
-	local_irq_restore(flags);
 }
 
 static void sci_stop_rx(struct uart_port *port)
 {
-	unsigned long flags;
 	unsigned short ctrl;
 
 	/* Clear RIE (Receive Interrupt Enable) bit in SCSCR */
-	local_irq_save(flags);
 	ctrl = sci_in(port, SCSCR);
 	ctrl &= ~(SCI_CTRL_FLAGS_RIE | SCI_CTRL_FLAGS_REIE);
 	sci_out(port, SCSCR, ctrl);
-	local_irq_restore(flags);
 }
 
 static void sci_enable_ms(struct uart_port *port)
@@ -963,9 +923,8 @@ static int sci_startup(struct uart_port *port)
 {
 	struct sci_port *s = &sci_ports[port->line];
 
-#if defined(__H8300S__)
-	h8300_sci_enable(port, sci_enable);
-#endif
+	if (s->enable)
+		s->enable(port);
 
 	sci_request_irq(s);
 	sci_start_tx(port);
@@ -982,9 +941,8 @@ static void sci_shutdown(struct uart_port *port)
 	sci_stop_tx(port);
 	sci_free_irq(s);
 
-#if defined(__H8300S__)
-	h8300_sci_enable(port, sci_disable);
-#endif
+	if (s->disable)
+		s->disable(port);
 }
 
 static void sci_set_termios(struct uart_port *port, struct termios *termios,
@@ -997,6 +955,23 @@ static void sci_set_termios(struct uart_port *port, struct termios *termios,
 
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
 
+	switch (baud) {
+		case 0:
+			t = -1;
+			break;
+		default:
+		{
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+			struct clk *clk = clk_get("module_clk");
+			t = SCBRR_VALUE(baud, clk_get_rate(clk));
+			clk_put(clk);
+#else
+			t = SCBRR_VALUE(baud);
+#endif
+		}
+			break;
+	}
+
 	spin_lock_irqsave(&port->lock, flags);
 
 	do {
@@ -1006,9 +981,8 @@ static void sci_set_termios(struct uart_port *port, struct termios *termios,
 	sci_out(port, SCSCR, 0x00);	/* TE=0, RE=0, CKE1=0 */
 
 #if !defined(SCI_ONLY)
-	if (port->type == PORT_SCIF) {
+	if (port->type == PORT_SCIF)
 		sci_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
-	}
 #endif
 
 	smr_val = sci_in(port, SCSMR) & 3;
@@ -1025,23 +999,6 @@ static void sci_set_termios(struct uart_port *port, struct termios *termios,
 
 	sci_out(port, SCSMR, smr_val);
 
-	switch (baud) {
-		case 0:
-			t = -1;
-			break;
-		default:
-		{
-#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
-			struct clk *clk = clk_get("module_clk");
-			t = SCBRR_VALUE(baud, clk_get_rate(clk));
-			clk_put(clk);
-#else
-			t = SCBRR_VALUE(baud);
-#endif
-		}
-			break;
-	}
-
 	if (t > 0) {
 		if(t >= 256) {
 			sci_out(port, SCSMR, (sci_in(port, SCSMR) & ~3) | 1);
@@ -1092,11 +1049,23 @@ static void sci_config_port(struct uart_port *port, int flags)
 
 	port->type = s->type;
 
+	switch (port->type) {
+	case PORT_SCI:
+		s->init_pins = sci_init_pins_sci;
+		break;
+	case PORT_SCIF:
+		s->init_pins = sci_init_pins_scif;
+		break;
+	case PORT_IRDA:
+		s->init_pins = sci_init_pins_irda;
+		break;
+	}
+
 #if defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
 	if (port->mapbase == 0)
 		port->mapbase = onchip_remap(SCIF_ADDR_SH5, 1024, "SCIF");
 
-	port->membase = (void *)port->mapbase;
+	port->membase = (void __iomem *)port->mapbase;
 #endif
 }
 
@@ -1132,412 +1101,61 @@ static struct uart_ops sci_uart_ops = {
 	.verify_port	= sci_verify_port,
 };
 
-static struct sci_port sci_ports[] = {
-#if defined(CONFIG_CPU_SUBTYPE_SH7708)
-	{
-		.port	= {
-			.membase	= (void *)0xfffffe80,
-			.mapbase	= 0xfffffe80,
-			.iotype		= UPIO_MEM,
-			.irq		= 25,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCI,
-		.irqs		= SCI_IRQS,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH7705)
-	{
-		.port	= {
-			.membase	= (void *)SCIF0,
-			.mapbase	= SCIF0,
-			.iotype		= UPIO_MEM,
-			.irq		= 55,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH3_IRDA_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-	{
-		.port	= {
-			.membase	= (void *)SCIF2,
-			.mapbase	= SCIF2,
-			.iotype		= UPIO_MEM,
-			.irq		= 59,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH3_SCIF_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	}
-#elif defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
-	{
-		.port	= {
-			.membase	= (void *)0xfffffe80,
-			.mapbase	= 0xfffffe80,
-			.iotype		= UPIO_MEM,
-			.irq		= 25,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCI,
-		.irqs		= SCI_IRQS,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0xa4000150,
-			.mapbase	= 0xa4000150,
-			.iotype		= UPIO_MEM,
-			.irq		= 59,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH3_SCIF_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0xa4000140,
-			.mapbase	= 0xa4000140,
-			.iotype		= UPIO_MEM,
-			.irq		= 55,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 2,
-		},
-		.type		= PORT_IRDA,
-		.irqs		= SH3_IRDA_IRQS,
-		.init_pins	= sci_init_pins_irda,
-	}
-#elif defined(CONFIG_CPU_SUBTYPE_SH7300)
-	{
-		.port	= {
-			.membase	= (void *)0xA4430000,
-			.mapbase	= 0xA4430000,
-			.iotype		= UPIO_MEM,
-			.irq		= 25,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7300_SCIF0_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH73180)
-	{
-		.port	= {
-			.membase	= (void *)0xffe00000,
-			.mapbase	= 0xffe00000,
-			.iotype		= UPIO_MEM,
-			.irq		= 25,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH73180_SCIF_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH4_202)
-	{
-		.port	= {
-			.membase	= (void *)0xffe80000,
-			.mapbase	= 0xffe80000,
-			.iotype		= UPIO_MEM,
-			.irq		= 43,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH4_SCIF_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH7750) || defined(CONFIG_CPU_SUBTYPE_SH7751)
-	{
-		.port	= {
-			.membase	= (void *)0xffe00000,
-			.mapbase	= 0xffe00000,
-			.iotype		= UPIO_MEM,
-			.irq		= 25,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCI,
-		.irqs		= SCI_IRQS,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0xffe80000,
-			.mapbase	= 0xffe80000,
-			.iotype		= UPIO_MEM,
-			.irq		= 43,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH4_SCIF_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH7760)
-	{
-		.port	= {
-			.membase	= (void *)0xfe600000,
-			.mapbase	= 0xfe600000,
-			.iotype		= UPIO_MEM,
-			.irq		= 55,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7760_SCIF0_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0xfe610000,
-			.mapbase	= 0xfe610000,
-			.iotype		= UPIO_MEM,
-			.irq		= 75,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7760_SCIF1_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0xfe620000,
-			.mapbase	= 0xfe620000,
-			.iotype		= UPIO_MEM,
-			.irq		= 79,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 2,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7760_SCIF2_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_ST40STB1)
-	{
-		.port	= {
-			.membase	= (void *)0xffe00000,
-			.mapbase	= 0xffe00000,
-			.iotype		= UPIO_MEM,
-			.irq		= 26,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= STB1_SCIF1_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0xffe80000,
-			.mapbase	= 0xffe80000,
-			.iotype		= UPIO_MEM,
-			.irq		= 43,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH4_SCIF_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
-	{
-		.port	= {
-			.iotype		= UPIO_MEM,
-			.irq		= 42,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH5_SCIF_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-#elif defined(CONFIG_H83007) || defined(CONFIG_H83068)
-	{
-		.port	= {
-			.membase	= (void *)0x00ffffb0,
-			.mapbase	= 0x00ffffb0,
-			.iotype		= UPIO_MEM,
-			.irq		= 54,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCI,
-		.irqs		= H8300H_SCI_IRQS0,
-		.init_pins	= sci_init_pins_sci,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0x00ffffb8,
-			.mapbase	= 0x00ffffb8,
-			.iotype		= UPIO_MEM,
-			.irq		= 58,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCI,
-		.irqs		= H8300H_SCI_IRQS1,
-		.init_pins	= sci_init_pins_sci,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0x00ffffc0,
-			.mapbase	= 0x00ffffc0,
-			.iotype		= UPIO_MEM,
-			.irq		= 62,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 2,
-		},
-		.type		= PORT_SCI,
-		.irqs		= H8300H_SCI_IRQS2,
-		.init_pins	= sci_init_pins_sci,
-	},
-#elif defined(CONFIG_H8S2678)
-	{
-		.port	= {
-			.membase	= (void *)0x00ffff78,
-			.mapbase	= 0x00ffff78,
-			.iotype		= UPIO_MEM,
-			.irq		= 90,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCI,
-		.irqs		= H8S_SCI_IRQS0,
-		.init_pins	= sci_init_pins_sci,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0x00ffff80,
-			.mapbase	= 0x00ffff80,
-			.iotype		= UPIO_MEM,
-			.irq		= 94,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCI,
-		.irqs		= H8S_SCI_IRQS1,
-		.init_pins	= sci_init_pins_sci,
-	},
-	{
-		.port	= {
-			.membase	= (void *)0x00ffff88,
-			.mapbase	= 0x00ffff88,
-			.iotype		= UPIO_MEM,
-			.irq		= 98,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 2,
-		},
-		.type		= PORT_SCI,
-		.irqs		= H8S_SCI_IRQS2,
-		.init_pins	= sci_init_pins_sci,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH7770)
-	{
-		.port   = {
-			.membase	= (void *)0xff923000,
-			.mapbase	= 0xff923000,
-			.iotype		= UPIO_MEM,
-			.irq		= 61,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7770_SCIF0_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-	{
-		.port   = {
-			.membase	= (void *)0xff924000,
-			.mapbase	= 0xff924000,
-			.iotype		= UPIO_MEM,
-			.irq		= 62,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7770_SCIF1_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-	{
-		.port   = {
-			.membase	= (void *)0xff925000,
-			.mapbase	= 0xff925000,
-			.iotype		= UPIO_MEM,
-			.irq		= 63,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 2,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7770_SCIF2_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
-	{
-		.port   = {
-			.membase	= (void *)0xffe00000,
-			.mapbase	= 0xffe00000,
-			.iotype		= UPIO_MEM,
-			.irq		= 43,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7780_SCIF0_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
-	{
-		.port   = {
-			.membase	= (void *)0xffe10000,
-			.mapbase	= 0xffe10000,
-			.iotype		= UPIO_MEM,
-			.irq		= 79,
-			.ops		= &sci_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-		.type		= PORT_SCIF,
-		.irqs		= SH7780_SCIF1_IRQS,
-		.init_pins	= sci_init_pins_scif,
-	},
+static void __init sci_init_ports(void)
+{
+	static int first = 1;
+	int i;
+
+	if (!first)
+		return;
+
+	first = 0;
+
+	for (i = 0; i < SCI_NPORTS; i++) {
+		sci_ports[i].port.ops		= &sci_uart_ops;
+		sci_ports[i].port.iotype	= UPIO_MEM;
+		sci_ports[i].port.line		= i;
+		sci_ports[i].port.fifosize	= 1;
+
+#if defined(__H8300H__) || defined(__H8300S__)
+#ifdef __H8300S__
+		sci_ports[i].enable	= h8300_sci_enable;
+		sci_ports[i].disable	= h8300_sci_disable;
+#endif
+		sci_ports[i].port.uartclk = CONFIG_CPU_CLOCK;
+#elif defined(CONFIG_SUPERH64)
+		sci_ports[i].port.uartclk = current_cpu_data.module_clock * 16;
 #else
-#error "CPU subtype not defined"
+		/*
+		 * XXX: We should use a proper SCI/SCIF clock
+		 */
+		{
+			struct clk *clk = clk_get("module_clk");
+			sci_ports[i].port.uartclk = clk_get_rate(clk) * 16;
+			clk_put(clk);
+		}
 #endif
-};
+
+		sci_ports[i].break_timer.data = (unsigned long)&sci_ports[i];
+		sci_ports[i].break_timer.function = sci_break_timer;
+
+		init_timer(&sci_ports[i].break_timer);
+	}
+}
+
+int __init early_sci_setup(struct uart_port *port)
+{
+	if (unlikely(port->line > SCI_NPORTS))
+		return -ENODEV;
+
+	sci_init_ports();
+
+	sci_ports[port->line].port.membase	= port->membase;
+	sci_ports[port->line].port.mapbase	= port->mapbase;
+	sci_ports[port->line].port.type		= port->type;
+
+	return 0;
+}
 
 #ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
 /*
@@ -1559,34 +1177,38 @@ static int __init serial_console_setup(struct console *co, char *options)
 	int flow = 'n';
 	int ret;
 
+	/*
+	 * Check whether an invalid uart number has been specified, and
+	 * if so, search for the first available port that does have
+	 * console support.
+	 */
+	if (co->index >= SCI_NPORTS)
+		co->index = 0;
+
 	serial_console_port = &sci_ports[co->index];
 	port = &serial_console_port->port;
-	port->type = serial_console_port->type;
-
-#ifdef CONFIG_SUPERH64
-	/* This is especially needed on sh64 to remap the SCIF */
-	sci_config_port(port, 0);
-#endif
 
 	/*
-	 * We need to set the initial uartclk here, since otherwise it will
-	 * only ever be setup at sci_init() time.
+	 * Also need to check port->type, we don't actually have any
+	 * UPIO_PORT ports, but uart_report_port() handily misreports
+	 * it anyways if we don't have a port available by the time this is
+	 * called.
 	 */
-#if defined(__H8300H__) || defined(__H8300S__)
-	port->uartclk = CONFIG_CPU_CLOCK;
+	if (!port->type)
+		return -ENODEV;
+	if (!port->membase || !port->mapbase)
+		return -ENODEV;
+
+	spin_lock_init(&port->lock);
+
+	port->type = serial_console_port->type;
+
+	if (port->flags & UPF_IOREMAP)
+		sci_config_port(port, 0);
+
+	if (serial_console_port->enable)
+		serial_console_port->enable(port);
 
-#if defined(__H8300S__)
-	h8300_sci_enable(port, sci_enable);
-#endif
-#elif defined(CONFIG_SUPERH64)
-	port->uartclk = current_cpu_data.module_clock * 16;
-#else
-	{
-		struct clk *clk = clk_get("module_clk");
-		port->uartclk = clk_get_rate(clk) * 16;
-		clk_put(clk);
-	}
-#endif
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
 
@@ -1604,17 +1226,17 @@ static struct console serial_console = {
 	.device		= uart_console_device,
 	.write		= serial_console_write,
 	.setup		= serial_console_setup,
-	.flags		= CON_PRINTBUFFER,
+	.flags		= CON_PRINTBUFFER, 
 	.index		= -1,
 	.data		= &sci_uart_driver,
 };
 
 static int __init sci_console_init(void)
 {
+	sci_init_ports();
 	register_console(&serial_console);
 	return 0;
 }
-
 console_initcall(sci_console_init);
 #endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
 
@@ -1649,6 +1271,8 @@ int __init kgdb_console_setup(struct console *co, char *options)
 	int parity = 'n';
 	int flow = 'n';
 
+	spin_lock_init(&port->lock);
+
 	if (co->index != kgdb_portnum)
 		co->index = kgdb_portnum;
 
@@ -1677,10 +1301,10 @@ static struct console kgdb_console = {
 /* Register the KGDB console so we get messages (d'oh!) */
 static int __init kgdb_console_init(void)
 {
+	sci_init_ports();
 	register_console(&kgdb_console);
 	return 0;
 }
-
 console_initcall(kgdb_console_init);
 #endif /* CONFIG_SH_KGDB_CONSOLE */
 
@@ -1701,60 +1325,132 @@ static struct uart_driver sci_uart_driver = {
 	.dev_name	= "ttySC",
 	.major		= SCI_MAJOR,
 	.minor		= SCI_MINOR_START,
+	.nr		= SCI_NPORTS,
 	.cons		= SCI_CONSOLE,
 };
 
-static int __init sci_init(void)
+/*
+ * Register a set of serial devices attached to a platform device.  The
+ * list is terminated with a zero flags entry, which means we expect
+ * all entries to have at least UPF_BOOT_AUTOCONF set. Platforms that need
+ * remapping (such as sh64) should also set UPF_IOREMAP.
+ */
+static int __devinit sci_probe(struct platform_device *dev)
 {
-	int chan, ret;
+	struct plat_sci_port *p = dev->dev.platform_data;
+	int i;
 
-	printk("%s", banner);
+	for (i = 0; p && p->flags != 0 && i < SCI_NPORTS; p++, i++) {
+		struct sci_port *sciport = &sci_ports[i];
 
-	sci_uart_driver.nr = ARRAY_SIZE(sci_ports);
+		sciport->port.mapbase	= p->mapbase;
 
-	ret = uart_register_driver(&sci_uart_driver);
-	if (ret == 0) {
-		for (chan = 0; chan < SCI_NPORTS; chan++) {
-			struct sci_port *sciport = &sci_ports[chan];
+		/*
+		 * For the simple (and majority of) cases where we don't need
+		 * to do any remapping, just cast the cookie directly.
+		 */
+		if (p->mapbase && !p->membase && !(p->flags & UPF_IOREMAP))
+			p->membase = (void __iomem *)p->mapbase;
 
-#if defined(__H8300H__) || defined(__H8300S__)
-			sciport->port.uartclk = CONFIG_CPU_CLOCK;
-#elif defined(CONFIG_SUPERH64)
-			sciport->port.uartclk = current_cpu_data.module_clock * 16;
-#else
-			struct clk *clk = clk_get("module_clk");
-			sciport->port.uartclk = clk_get_rate(clk) * 16;
-			clk_put(clk);
-#endif
-			uart_add_one_port(&sci_uart_driver, &sciport->port);
-			sciport->break_timer.data = (unsigned long)sciport;
-			sciport->break_timer.function = sci_break_timer;
-			init_timer(&sciport->break_timer);
-		}
+		sciport->port.membase	= p->membase;
+
+		sciport->port.irq	= p->irqs[SCIx_TXI_IRQ];
+		sciport->port.flags	= p->flags;
+		sciport->port.dev	= &dev->dev;
+
+		sciport->type		= sciport->port.type = p->type;
+
+		memcpy(&sciport->irqs, &p->irqs, sizeof(p->irqs));
+
+		uart_add_one_port(&sci_uart_driver, &sciport->port);
 	}
 
 #ifdef CONFIG_CPU_FREQ
 	cpufreq_register_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER);
-	printk("sci: CPU frequency notifier registered\n");
+	dev_info(&dev->dev, "sci: CPU frequency notifier registered\n");
 #endif
 
 #ifdef CONFIG_SH_STANDARD_BIOS
 	sh_bios_gdb_detach();
 #endif
 
-	return ret;
+	return 0;
 }
 
-static void __exit sci_exit(void)
+static int __devexit sci_remove(struct platform_device *dev)
+{
+	int i;
+
+	for (i = 0; i < SCI_NPORTS; i++)
+		uart_remove_one_port(&sci_uart_driver, &sci_ports[i].port);
+
+	return 0;
+}
+
+static int sci_suspend(struct platform_device *dev, pm_message_t state)
 {
-	int chan;
+	int i;
+
+	for (i = 0; i < SCI_NPORTS; i++) {
+		struct sci_port *p = &sci_ports[i];
+
+		if (p->type != PORT_UNKNOWN && p->port.dev == &dev->dev)
+			uart_suspend_port(&sci_uart_driver, &p->port);
+	}
 
-	for (chan = 0; chan < SCI_NPORTS; chan++)
-		uart_remove_one_port(&sci_uart_driver, &sci_ports[chan].port);
+	return 0;
+}
 
+static int sci_resume(struct platform_device *dev)
+{
+	int i;
+
+	for (i = 0; i < SCI_NPORTS; i++) {
+		struct sci_port *p = &sci_ports[i];
+
+		if (p->type != PORT_UNKNOWN && p->port.dev == &dev->dev)
+			uart_resume_port(&sci_uart_driver, &p->port);
+	}
+
+	return 0;
+}
+
+static struct platform_driver sci_driver = {
+	.probe		= sci_probe,
+	.remove		= __devexit_p(sci_remove),
+	.suspend	= sci_suspend,
+	.resume		= sci_resume,
+	.driver		= {
+		.name	= "sh-sci",
+		.owner	= THIS_MODULE,
+	},
+};
+
+static int __init sci_init(void)
+{
+	int ret;
+
+	printk(banner);
+
+	sci_init_ports();
+
+	ret = uart_register_driver(&sci_uart_driver);
+	if (likely(ret == 0)) {
+		ret = platform_driver_register(&sci_driver);
+		if (unlikely(ret))
+			uart_unregister_driver(&sci_uart_driver);
+	}
+
+	return ret;
+}
+
+static void __exit sci_exit(void)
+{
+	platform_driver_unregister(&sci_driver);
 	uart_unregister_driver(&sci_uart_driver);
 }
 
 module_init(sci_init);
 module_exit(sci_exit);
 
+MODULE_LICENSE("GPL");
diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h
index ab320fa3237..28643c4dc85 100644
--- a/drivers/serial/sh-sci.h
+++ b/drivers/serial/sh-sci.h
@@ -10,7 +10,9 @@
  *  Modified to support SH7300(SH-Mobile) SCIF. Takashi Kusuda (Jun 2003).
  *  Modified to support H8/300 Series Yoshinori Sato (Feb 2004).
  */
+#include <linux/config.h>
 #include <linux/serial_core.h>
+#include <asm/io.h>
 
 #if defined(__H8300H__) || defined(__H8300S__)
 #include <asm/gpio.h>
@@ -22,40 +24,13 @@
 #endif
 #endif
 
-/* Offsets into the sci_port->irqs array */
-#define SCIx_ERI_IRQ 0
-#define SCIx_RXI_IRQ 1
-#define SCIx_TXI_IRQ 2
-
-/*                     ERI, RXI, TXI, BRI */
-#define SCI_IRQS      { 23,  24,  25,   0 }
-#define SH3_SCIF_IRQS { 56,  57,  59,  58 }
-#define SH3_IRDA_IRQS { 52,  53,  55,  54 }
-#define SH4_SCIF_IRQS { 40,  41,  43,  42 }
-#define STB1_SCIF1_IRQS {23, 24,  26,  25 }
-#define SH7760_SCIF0_IRQS { 52, 53, 55, 54 }
-#define SH7760_SCIF1_IRQS { 72, 73, 75, 74 }
-#define SH7760_SCIF2_IRQS { 76, 77, 79, 78 }
-#define SH7300_SCIF0_IRQS {80,  80,  80,  80 }
-#define SH73180_SCIF_IRQS {80,  81,  83,  82 }
-#define H8300H_SCI_IRQS0 {52, 53, 54,   0 }
-#define H8300H_SCI_IRQS1 {56, 57, 58,   0 }
-#define H8300H_SCI_IRQS2 {60, 61, 62,   0 }
-#define H8S_SCI_IRQS0 {88, 89, 90,   0 }
-#define H8S_SCI_IRQS1 {92, 93, 94,   0 }
-#define H8S_SCI_IRQS2 {96, 97, 98,   0 }
-#define SH5_SCIF_IRQS {39, 40, 42,   0 }
-#define	SH7770_SCIF0_IRQS {61, 61, 61, 61 }
-#define	SH7770_SCIF1_IRQS {62, 62, 62, 62 }
-#define	SH7770_SCIF2_IRQS {63, 63, 63, 63 }
-#define	SH7780_SCIF0_IRQS {40, 41, 43, 42 }
-#define	SH7780_SCIF1_IRQS {76, 77, 79, 78 }
-
 #if defined(CONFIG_CPU_SUBTYPE_SH7708)
 # define SCSPTR 0xffffff7c /* 8 bit */
 # define SCSCR_INIT(port)          0x30 /* TIE=0,RIE=0,TE=1,RE=1 */
 # define SCI_ONLY
-#elif defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7707) || \
+      defined(CONFIG_CPU_SUBTYPE_SH7709) || \
+      defined(CONFIG_CPU_SUBTYPE_SH7706)
 # define SCPCR  0xA4000116 /* 16 bit SCI and SCIF */
 # define SCPDR  0xA4000136 /* 8  bit SCI and SCIF */
 # define SCSCR_INIT(port)          0x30 /* TIE=0,RIE=0,TE=1,RE=1 */
@@ -99,12 +74,23 @@
 # define SCPDR  0xA4050136        /* 16 bit SCIF */
 # define SCSCR_INIT(port)  0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
 # define SCIF_ONLY
+#elif defined(CONFIG_CPU_SUBTYPE_SH7710)
+# define SCSPTR0 0xA4400000	  /* 16 bit SCIF */
+# define SCSCR_INIT(port)  0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
+# define SCIF_ONLY
 #elif defined(CONFIG_CPU_SUBTYPE_SH73180)
 # define SCPDR  0xA4050138        /* 16 bit SCIF */
 # define SCSPTR2 SCPDR
 # define SCIF_ORER 0x0001   /* overrun error bit */
 # define SCSCR_INIT(port)  0x0038 /* TIE=0,RIE=0,TE=1,RE=1 */
 # define SCIF_ONLY
+#elif defined(CONFIG_CPU_SUBTYPE_SH7343)
+# define SCSPTR0 0xffe00010	/* 16 bit SCIF */
+# define SCSPTR1 0xffe10010	/* 16 bit SCIF */
+# define SCSPTR2 0xffe20010	/* 16 bit SCIF */
+# define SCSPTR3 0xffe30010	/* 16 bit SCIF */
+# define SCSCR_INIT(port) 0x32	/* TIE=0,RIE=0,TE=1,RE=1,REIE=0,CKE=1 */
+# define SCIF_ONLY
 #elif defined(CONFIG_CPU_SUBTYPE_SH4_202)
 # define SCSPTR2 0xffe80020 /* 16 bit SCIF */
 # define SCIF_ORER 0x0001   /* overrun error bit */
@@ -145,7 +131,7 @@
 #elif defined(CONFIG_CPU_SUBTYPE_SH7780)
 # define SCSPTR0	0xffe00024	/* 16 bit SCIF */
 # define SCSPTR1	0xffe10024	/* 16 bit SCIF */
-# define SCIF_OPER	0x0001		/* Overrun error bit */
+# define SCIF_ORER	0x0001		/* Overrun error bit */
 # define SCSCR_INIT(port)	0x3a	/* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
 # define SCIF_ONLY
 #else
@@ -273,15 +259,6 @@
  */
 #define SCI_EVENT_WRITE_WAKEUP	0
 
-struct sci_port {
-	struct uart_port port;
-	int type;
-	unsigned char irqs[4]; /* ERI, RXI, TXI, BRI */
-	void (*init_pins)(struct uart_port *port, unsigned int cflag);
-	int break_flag;
-	struct timer_list break_timer;
-};
-
 #define SCI_IN(size, offset)					\
   unsigned int addr = port->mapbase + (offset);			\
   if ((size) == 8) {						\
@@ -336,7 +313,9 @@ struct sci_port {
   }
 
 #ifdef CONFIG_CPU_SH3
-#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7705)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7705) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7710)
 #define SCIF_FNS(name, scif_offset, scif_size) \
   CPU_SCIF_FNS(name, scif_offset, scif_size)
 #else
@@ -362,7 +341,9 @@ struct sci_port {
   CPU_SCIF_FNS(name, sh4_scif_offset, sh4_scif_size)
 #endif
 
-#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7705)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7705) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7710)
 SCIF_FNS(SCSMR,  0x00, 16)
 SCIF_FNS(SCBRR,  0x04,  8)
 SCIF_FNS(SCSCR,  0x08, 16)
@@ -447,7 +428,9 @@ static inline int sci_rxd_in(struct uart_port *port)
 		return ctrl_inb(SCSPTR)&0x01 ? 1 : 0; /* SCI */
 	return 1;
 }
-#elif defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7707) || \
+      defined(CONFIG_CPU_SUBTYPE_SH7709) || \
+      defined(CONFIG_CPU_SUBTYPE_SH7706)
 static inline int sci_rxd_in(struct uart_port *port)
 {
 	if (port->mapbase == 0xfffffe80)
@@ -467,6 +450,13 @@ static inline int sci_rxd_in(struct uart_port *port)
 		return ctrl_inb(SCPDR)&0x10 ? 1 : 0; /* SCIF */
 	return 1;
 }
+#elif defined(CONFIG_CPU_SUBTYPE_SH7710)
+static inline int sci_rxd_in(struct uart_port *port)
+{
+	if (port->mapbase == SCSPTR0)
+		return ctrl_inw(SCSPTR0 + 0x10) & 0x01 ? 1 : 0;
+	return 1;
+}
 #elif defined(CONFIG_CPU_SUBTYPE_SH7750) || \
       defined(CONFIG_CPU_SUBTYPE_SH7751) || \
       defined(CONFIG_CPU_SUBTYPE_SH4_202)
@@ -504,6 +494,19 @@ static inline int sci_rxd_in(struct uart_port *port)
 {
 	return ctrl_inb(SCPDR)&0x01 ? 1 : 0; /* SCIF0 */
 }
+#elif defined(CONFIG_CPU_SUBTYPE_SH7343)
+static inline int sci_rxd_in(struct uart_port *port)
+{
+	if (port->mapbase == 0xffe00000)
+		return ctrl_inw(SCSPTR0) & 0x0001 ? 1 : 0; /* SCIF */
+	if (port->mapbase == 0xffe10000)
+		return ctrl_inw(SCSPTR1) & 0x0001 ? 1 : 0; /* SCIF */
+	if (port->mapbase == 0xffe20000)
+		return ctrl_inw(SCSPTR2) & 0x0001 ? 1 : 0; /* SCIF */
+	if (port->mapbase == 0xffe30000)
+		return ctrl_inw(SCSPTR3) & 0x0001 ? 1 : 0; /* SCIF */
+	return 1;
+}
 #elif defined(CONFIG_CPU_SUBTYPE_ST40STB1)
 static inline int sci_rxd_in(struct uart_port *port)
 {
@@ -587,4 +590,3 @@ static inline int sci_rxd_in(struct uart_port *port)
 #else /* Generic SH */
 #define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(32*bps)-1)
 #endif
-