Merge branch 'linus' into percpu-cpumask-x86-for-linus-2

Conflicts:
	arch/sparc/kernel/time_64.c
	drivers/gpu/drm/drm_proc.c

Manual merge to resolve build warning due to phys_addr_t type change
on x86:

	drivers/gpu/drm/drm_info.c

Signed-off-by: Ingo Molnar <mingo@elte.hu>

1 files changed, 53 insertions, 31 deletions

diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 12a52efcd0d..3b83a80e3fe 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -93,12 +93,9 @@ struct ieee80211_ht_bss_info {
  * enum ieee80211_max_queues - maximum number of queues
  *
  * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
- * @IEEE80211_MAX_AMPDU_QUEUES: Maximum number of queues usable
- *	for A-MPDU operation.
  */
 enum ieee80211_max_queues {
-	IEEE80211_MAX_QUEUES =		16,
-	IEEE80211_MAX_AMPDU_QUEUES =	16,
+	IEEE80211_MAX_QUEUES =		4,
 };
 
 /**
@@ -245,6 +242,12 @@ struct ieee80211_bss_conf {
  * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
  *	set by rate control algorithms to indicate probe rate, will
  *	be cleared for fragmented frames (except on the last fragment)
+ * @IEEE80211_TX_INTFL_RCALGO: mac80211 internal flag, do not test or
+ *	set this flag in the driver; indicates that the rate control
+ *	algorithm was used and should be notified of TX status
+ * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
+ *	used to indicate that a pending frame requires TX processing before
+ *	it can be sent out.
  */
 enum mac80211_tx_control_flags {
 	IEEE80211_TX_CTL_REQ_TX_STATUS		= BIT(0),
@@ -260,6 +263,8 @@ enum mac80211_tx_control_flags {
 	IEEE80211_TX_STAT_AMPDU			= BIT(10),
 	IEEE80211_TX_STAT_AMPDU_NO_BACK		= BIT(11),
 	IEEE80211_TX_CTL_RATE_CTRL_PROBE	= BIT(12),
+	IEEE80211_TX_INTFL_RCALGO		= BIT(13),
+	IEEE80211_TX_INTFL_NEED_TXPROCESSING	= BIT(14),
 };
 
 /**
@@ -520,12 +525,6 @@ enum ieee80211_conf_flags {
 	IEEE80211_CONF_PS		= (1<<1),
 };
 
-/* XXX: remove all this once drivers stop trying to use it */
-static inline int __deprecated __IEEE80211_CONF_SHORT_SLOT_TIME(void)
-{
-	return 0;
-}
-#define IEEE80211_CONF_SHORT_SLOT_TIME (__IEEE80211_CONF_SHORT_SLOT_TIME())
 
 /**
  * enum ieee80211_conf_changed - denotes which configuration changed
@@ -888,6 +887,10 @@ enum ieee80211_tkip_key_type {
  *
  * @IEEE80211_HW_MFP_CAPABLE:
  *	Hardware supports management frame protection (MFP, IEEE 802.11w).
+ *
+ * @IEEE80211_HW_BEACON_FILTER:
+ *	Hardware supports dropping of irrelevant beacon frames to
+ *	avoid waking up cpu.
  */
 enum ieee80211_hw_flags {
 	IEEE80211_HW_RX_INCLUDES_FCS			= 1<<1,
@@ -903,6 +906,7 @@ enum ieee80211_hw_flags {
 	IEEE80211_HW_PS_NULLFUNC_STACK			= 1<<11,
 	IEEE80211_HW_SUPPORTS_DYNAMIC_PS		= 1<<12,
 	IEEE80211_HW_MFP_CAPABLE			= 1<<13,
+	IEEE80211_HW_BEACON_FILTER			= 1<<14,
 };
 
 /**
@@ -945,12 +949,6 @@ enum ieee80211_hw_flags {
  *	data packets. WMM/QoS requires at least four, these
  *	queues need to have configurable access parameters.
  *
- * @ampdu_queues: number of available hardware transmit queues
- *	for A-MPDU packets, these have no access parameters
- *	because they're used only for A-MPDU frames. Note that
- *	mac80211 will not currently use any of the regular queues
- *	for aggregation.
- *
  * @rate_control_algorithm: rate control algorithm for this hardware.
  *	If unset (NULL), the default algorithm will be used. Must be
  *	set before calling ieee80211_register_hw().
@@ -975,7 +973,6 @@ struct ieee80211_hw {
 	int vif_data_size;
 	int sta_data_size;
 	u16 queues;
-	u16 ampdu_queues;
 	u16 max_listen_interval;
 	s8 max_signal;
 	u8 max_rates;
@@ -1017,11 +1014,6 @@ static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
 	memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
 }
 
-static inline int ieee80211_num_regular_queues(struct ieee80211_hw *hw)
-{
-	return hw->queues;
-}
-
 static inline struct ieee80211_rate *
 ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
 		      const struct ieee80211_tx_info *c)
@@ -1132,6 +1124,24 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
  */
 
 /**
+ * DOC: Beacon filter support
+ *
+ * Some hardware have beacon filter support to reduce host cpu wakeups
+ * which will reduce system power consumption. It usuallly works so that
+ * the firmware creates a checksum of the beacon but omits all constantly
+ * changing elements (TSF, TIM etc). Whenever the checksum changes the
+ * beacon is forwarded to the host, otherwise it will be just dropped. That
+ * way the host will only receive beacons where some relevant information
+ * (for example ERP protection or WMM settings) have changed.
+ *
+ * Beacon filter support is informed with %IEEE80211_HW_BEACON_FILTER flag.
+ * The driver needs to enable beacon filter support whenever power save is
+ * enabled, that is %IEEE80211_CONF_PS is set. When power save is enabled,
+ * the stack will not check for beacon miss at all and the driver needs to
+ * notify about complete loss of beacons with ieee80211_beacon_loss().
+ */
+
+/**
  * DOC: Frame filtering
  *
  * mac80211 requires to see many management frames for proper
@@ -1220,14 +1230,14 @@ enum ieee80211_filter_flags {
  * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
  * @IEEE80211_AMPDU_TX_START: start Tx aggregation
  * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
- * @IEEE80211_AMPDU_TX_RESUME: resume TX aggregation
+ * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
  */
 enum ieee80211_ampdu_mlme_action {
 	IEEE80211_AMPDU_RX_START,
 	IEEE80211_AMPDU_RX_STOP,
 	IEEE80211_AMPDU_TX_START,
 	IEEE80211_AMPDU_TX_STOP,
-	IEEE80211_AMPDU_TX_RESUME,
+	IEEE80211_AMPDU_TX_OPERATIONAL,
 };
 
 /**
@@ -1318,11 +1328,13 @@ enum ieee80211_ampdu_mlme_action {
  *
  * @hw_scan: Ask the hardware to service the scan request, no need to start
  *	the scan state machine in stack. The scan must honour the channel
- *	configuration done by the regulatory agent in the wiphy's registered
- *	bands. When the scan finishes, ieee80211_scan_completed() must be
- *	called; note that it also must be called when the scan cannot finish
- *	because the hardware is turned off! Anything else is a bug!
- *	Returns a negative error code which will be seen in userspace.
+ *	configuration done by the regulatory agent in the wiphy's
+ *	registered bands. The hardware (or the driver) needs to make sure
+ *	that power save is disabled. When the scan finishes,
+ *	ieee80211_scan_completed() must be called; note that it also must
+ *	be called when the scan cannot finish because the hardware is
+ *	turned off! Anything else is a bug! Returns a negative error code
+ *	which will be seen in userspace.
  *
  * @sw_scan_start: Notifier function that is called just before a software scan
  *	is started. Can be NULL, if the driver doesn't need this notification.
@@ -1350,8 +1362,8 @@ enum ieee80211_ampdu_mlme_action {
  * @get_tx_stats: Get statistics of the current TX queue status. This is used
  *	to get number of currently queued packets (queue length), maximum queue
  *	size (limit), and total number of packets sent using each TX queue
- *	(count). The 'stats' pointer points to an array that has hw->queues +
- *	hw->ampdu_queues items.
+ *	(count). The 'stats' pointer points to an array that has hw->queues
+ *	items.
  *
  * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
  *	this is only used for IBSS mode BSSID merging and debugging. Is not a
@@ -1979,6 +1991,16 @@ void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
 struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_hw *hw,
 					 const u8 *addr);
 
+/**
+ * ieee80211_beacon_loss - inform hardware does not receive beacons
+ *
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
+ *
+ * When beacon filtering is enabled with IEEE80211_HW_BEACON_FILTERING and
+ * IEEE80211_CONF_PS is set, the driver needs to inform whenever the
+ * hardware is not receiving beacons with this function.
+ */
+void ieee80211_beacon_loss(struct ieee80211_vif *vif);
 
 /* Rate control API */