aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--drivers/net/Kconfig20
-rw-r--r--drivers/net/Makefile1
-rw-r--r--drivers/net/sky2.c3039
-rw-r--r--drivers/net/sky2.h1910
-rw-r--r--include/linux/netdevice.h8
5 files changed, 4975 insertions, 3 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index ebd7313d7fc..39415b5c456 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2008,7 +2008,25 @@ config SKGE
It does not support the link failover and network management
features that "portable" vendor supplied sk98lin driver does.
-
+
+
+config SKY2
+ tristate "SysKonnect Yukon2 support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ ---help---
+ This driver support the Marvell Yukon 2 Gigabit Ethernet adapter.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sky2. This is recommended.
+
+config SKY2_EC_A1
+ bool "Support old Yukon-EC A1 chipset"
+ depends on SKY2
+ ---help---
+ Include support for early revisions of the Yukon EC chipset
+ that required extra workarounds. If in doubt, say N.
+
config SK98LIN
tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support"
depends on PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 4cffd34442a..27822a2f068 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -59,6 +59,7 @@ spidernet-y += spider_net.o spider_net_ethtool.o sungem_phy.o
obj-$(CONFIG_SPIDER_NET) += spidernet.o
obj-$(CONFIG_TC35815) += tc35815.o
obj-$(CONFIG_SKGE) += skge.o
+obj-$(CONFIG_SKY2) += sky2.o
obj-$(CONFIG_SK98LIN) += sk98lin/
obj-$(CONFIG_SKFP) += skfp/
obj-$(CONFIG_VIA_RHINE) += via-rhine.o
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
new file mode 100644
index 00000000000..9f89000e5ad
--- /dev/null
+++ b/drivers/net/sky2.c
@@ -0,0 +1,3039 @@
+/*
+ * New driver for Marvell Yukon 2 chipset.
+ * Based on earlier sk98lin, and skge driver.
+ *
+ * This driver intentionally does not support all the features
+ * of the original driver such as link fail-over and link management because
+ * those should be done at higher levels.
+ *
+ * Copyright (C) 2005 Stephen Hemminger <shemminger@osdl.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/*
+ * TODO
+ * - coalescing setting?
+ *
+ * TOTEST
+ * - speed setting
+ * - suspend/resume
+ */
+
+#include <linux/config.h>
+#include <linux/crc32.h>
+#include <linux/kernel.h>
+#include <linux/version.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/dma-mapping.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/pci.h>
+#include <linux/ip.h>
+#include <linux/tcp.h>
+#include <linux/in.h>
+#include <linux/delay.h>
+#include <linux/if_vlan.h>
+
+#include <asm/irq.h>
+
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+#define SKY2_VLAN_TAG_USED 1
+#endif
+
+#include "sky2.h"
+
+#define DRV_NAME "sky2"
+#define DRV_VERSION "0.7"
+#define PFX DRV_NAME " "
+
+/*
+ * The Yukon II chipset takes 64 bit command blocks (called list elements)
+ * that are organized into three (receive, transmit, status) different rings
+ * similar to Tigon3. A transmit can require several elements;
+ * a receive requires one (or two if using 64 bit dma).
+ */
+
+#ifdef CONFIG_SKY2_EC_A1
+#define is_ec_a1(hw) \
+ ((hw)->chip_id == CHIP_ID_YUKON_EC && \
+ (hw)->chip_rev == CHIP_REV_YU_EC_A1)
+#else
+#define is_ec_a1(hw) 0
+#endif
+
+#define RX_LE_SIZE 256
+#define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le))
+#define RX_MAX_PENDING (RX_LE_SIZE/2 - 2)
+#define RX_DEF_PENDING 128
+#define RX_COPY_THRESHOLD 256
+
+#define TX_RING_SIZE 512
+#define TX_DEF_PENDING (TX_RING_SIZE - 1)
+#define TX_MIN_PENDING 64
+#define MAX_SKB_TX_LE (4 + 2*MAX_SKB_FRAGS)
+
+#define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */
+#define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
+#define ETH_JUMBO_MTU 9000
+#define TX_WATCHDOG (5 * HZ)
+#define NAPI_WEIGHT 64
+#define PHY_RETRIES 1000
+
+static const u32 default_msg =
+ NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK
+ | NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR
+ | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN | NETIF_MSG_INTR;
+
+static int debug = -1; /* defaults above */
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
+static const struct pci_device_id sky2_id_table[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) },
+ { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) },
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) },
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b01) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) },
+ { 0 }
+};
+
+MODULE_DEVICE_TABLE(pci, sky2_id_table);
+
+/* Avoid conditionals by using array */
+static const unsigned txqaddr[] = { Q_XA1, Q_XA2 };
+static const unsigned rxqaddr[] = { Q_R1, Q_R2 };
+
+static const char *yukon_name[] = {
+ [CHIP_ID_YUKON_LITE - CHIP_ID_YUKON] = "Lite", /* 0xb0 */
+ [CHIP_ID_YUKON_LP - CHIP_ID_YUKON] = "LP", /* 0xb2 */
+ [CHIP_ID_YUKON_XL - CHIP_ID_YUKON] = "XL", /* 0xb3 */
+
+ [CHIP_ID_YUKON_EC - CHIP_ID_YUKON] = "EC", /* 0xb6 */
+ [CHIP_ID_YUKON_FE - CHIP_ID_YUKON] = "FE", /* 0xb7 */
+};
+
+
+/* Access to external PHY */
+static void gm_phy_write(struct sky2_hw *hw, unsigned port, u16 reg, u16 val)
+{
+ int i;
+
+ gma_write16(hw, port, GM_SMI_DATA, val);
+ gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) | GM_SMI_CT_REG_AD(reg));
+
+ for (i = 0; i < PHY_RETRIES; i++) {
+ if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
+ return;
+ udelay(1);
+ }
+ printk(KERN_WARNING PFX "%s: phy write timeout\n", hw->dev[port]->name);
+}
+
+static u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg)
+{
+ int i;
+
+ gma_write16(hw, port, GM_SMI_CTRL, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV)
+ | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
+
+ for (i = 0; i < PHY_RETRIES; i++) {
+ if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL)
+ goto ready;
+ udelay(1);
+ }
+
+ printk(KERN_WARNING PFX "%s: phy read timeout\n", hw->dev[port]->name);
+ready:
+ return gma_read16(hw, port, GM_SMI_DATA);
+}
+
+static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
+{
+ u16 power_control;
+ u32 reg1;
+ int vaux;
+ int ret = 0;
+
+ pr_debug("sky2_set_power_state %d\n", state);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+
+ pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_PMC, &power_control);
+ vaux = (sky2_read8(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
+ (power_control & PCI_PM_CAP_PME_D3cold);
+
+ pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_CTRL, &power_control);
+
+ power_control |= PCI_PM_CTRL_PME_STATUS;
+ power_control &= ~(PCI_PM_CTRL_STATE_MASK);
+
+ switch (state) {
+ case PCI_D0:
+ /* switch power to VCC (WA for VAUX problem) */
+ sky2_write8(hw, B0_POWER_CTRL,
+ PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
+
+ /* disable Core Clock Division, */
+ sky2_write32(hw, B2_Y2_CLK_CTRL, Y2_CLK_DIV_DIS);
+
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
+ /* enable bits are inverted */
+ sky2_write8(hw, B2_Y2_CLK_GATE,
+ Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
+ Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
+ Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
+ else
+ sky2_write8(hw, B2_Y2_CLK_GATE, 0);
+
+ /* Turn off phy power saving */
+ pci_read_config_dword(hw->pdev, PCI_DEV_REG1, &reg1);
+ reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
+
+ /* looks like this XL is back asswards .. */
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) {
+ reg1 |= PCI_Y2_PHY1_COMA;
+ if (hw->ports > 1)
+ reg1 |= PCI_Y2_PHY2_COMA;
+ }
+ pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+ break;
+
+ case PCI_D3hot:
+ case PCI_D3cold:
+ /* Turn on phy power saving */
+ pci_read_config_dword(hw->pdev, PCI_DEV_REG1, &reg1);
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
+ reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
+ else
+ reg1 |= (PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
+ pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
+ sky2_write8(hw, B2_Y2_CLK_GATE, 0);
+ else
+ /* enable bits are inverted */
+ sky2_write8(hw, B2_Y2_CLK_GATE,
+ Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
+ Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
+ Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
+
+ /* switch power to VAUX */
+ if (vaux && state != PCI_D3cold)
+ sky2_write8(hw, B0_POWER_CTRL,
+ (PC_VAUX_ENA | PC_VCC_ENA |
+ PC_VAUX_ON | PC_VCC_OFF));
+ break;
+ default:
+ printk(KERN_ERR PFX "Unknown power state %d\n", state);
+ ret = -1;
+ }
+
+ pci_write_config_byte(hw->pdev, hw->pm_cap + PCI_PM_CTRL, power_control);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+ return ret;
+}
+
+static void sky2_phy_reset(struct sky2_hw *hw, unsigned port)
+{
+ u16 reg;
+
+ /* disable all GMAC IRQ's */
+ sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
+ /* disable PHY IRQs */
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
+
+ gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */
+ gma_write16(hw, port, GM_MC_ADDR_H2, 0);
+ gma_write16(hw, port, GM_MC_ADDR_H3, 0);
+ gma_write16(hw, port, GM_MC_ADDR_H4, 0);
+
+ reg = gma_read16(hw, port, GM_RX_CTRL);
+ reg |= GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA;
+ gma_write16(hw, port, GM_RX_CTRL, reg);
+}
+
+static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
+{
+ struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
+ u16 ctrl, ct1000, adv, pg, ledctrl, ledover;
+
+ if (sky2->autoneg == AUTONEG_ENABLE && hw->chip_id != CHIP_ID_YUKON_XL) {
+ u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
+
+ ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
+ PHY_M_EC_MAC_S_MSK);
+ ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ);
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC)
+ ectrl |= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA;
+ else
+ ectrl |= PHY_M_EC_M_DSC(2) | PHY_M_EC_S_DSC(3);
+
+ gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl);
+ }
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ if (hw->copper) {
+ if (hw->chip_id == CHIP_ID_YUKON_FE) {
+ /* enable automatic crossover */
+ ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1;
+ } else {
+ /* disable energy detect */
+ ctrl &= ~PHY_M_PC_EN_DET_MSK;
+
+ /* enable automatic crossover */
+ ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
+
+ if (sky2->autoneg == AUTONEG_ENABLE &&
+ hw->chip_id == CHIP_ID_YUKON_XL) {
+ ctrl &= ~PHY_M_PC_DSC_MSK;
+ ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
+ }
+ }
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+ } else {
+ /* workaround for deviation #4.88 (CRC errors) */
+ /* disable Automatic Crossover */
+
+ ctrl &= ~PHY_M_PC_MDIX_MSK;
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+ if (hw->chip_id == CHIP_ID_YUKON_XL) {
+ /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ ctrl &= ~PHY_M_MAC_MD_MSK;
+ ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+ /* select page 1 to access Fiber registers */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1);
+ }
+ }
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
+ if (sky2->autoneg == AUTONEG_DISABLE)
+ ctrl &= ~PHY_CT_ANE;
+ else
+ ctrl |= PHY_CT_ANE;
+
+ ctrl |= PHY_CT_RESET;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ ctrl = 0;
+ ct1000 = 0;
+ adv = PHY_AN_CSMA;
+
+ if (sky2->autoneg == AUTONEG_ENABLE) {
+ if (hw->copper) {
+ if (sky2->advertising & ADVERTISED_1000baseT_Full)
+ ct1000 |= PHY_M_1000C_AFD;
+ if (sky2->advertising & ADVERTISED_1000baseT_Half)
+ ct1000 |= PHY_M_1000C_AHD;
+ if (sky2->advertising & ADVERTISED_100baseT_Full)
+ adv |= PHY_M_AN_100_FD;
+ if (sky2->advertising & ADVERTISED_100baseT_Half)
+ adv |= PHY_M_AN_100_HD;
+ if (sky2->advertising & ADVERTISED_10baseT_Full)
+ adv |= PHY_M_AN_10_FD;
+ if (sky2->advertising & ADVERTISED_10baseT_Half)
+ adv |= PHY_M_AN_10_HD;
+ } else /* special defines for FIBER (88E1011S only) */
+ adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
+
+ /* Set Flow-control capabilities */
+ if (sky2->tx_pause && sky2->rx_pause)
+ adv |= PHY_AN_PAUSE_CAP; /* symmetric */
+ else if (sky2->rx_pause && !sky2->tx_pause)
+ adv |= PHY_AN_PAUSE_ASYM | PHY_AN_PAUSE_CAP;
+ else if (!sky2->rx_pause && sky2->tx_pause)
+ adv |= PHY_AN_PAUSE_ASYM; /* local */
+
+ /* Restart Auto-negotiation */
+ ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ /* forced speed/duplex settings */
+ ct1000 = PHY_M_1000C_MSE;
+
+ if (sky2->duplex == DUPLEX_FULL)
+ ctrl |= PHY_CT_DUP_MD;
+
+ switch (sky2->speed) {
+ case SPEED_1000:
+ ctrl |= PHY_CT_SP1000;
+ break;
+ case SPEED_100:
+ ctrl |= PHY_CT_SP100;
+ break;
+ }
+
+ ctrl |= PHY_CT_RESET;
+ }
+
+ if (hw->chip_id != CHIP_ID_YUKON_FE)
+ gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
+
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ /* Setup Phy LED's */
+ ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
+ ledover = 0;
+
+ switch (hw->chip_id) {
+ case CHIP_ID_YUKON_FE:
+ /* on 88E3082 these bits are at 11..9 (shifted left) */
+ ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1;
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR);
+
+ /* delete ACT LED control bits */
+ ctrl &= ~PHY_M_FELP_LED1_MSK;
+ /* change ACT LED control to blink mode */
+ ctrl |= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL);
+ gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl);
+ break;
+
+ case CHIP_ID_YUKON_XL:
+ pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+
+ /* select page 3 to access LED control register */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
+
+ /* set LED Function Control register */
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
+ PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */
+ PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
+ PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */
+
+ /* set Polarity Control register */
+ gm_phy_write(hw, port, PHY_MARV_PHY_STAT,
+ (PHY_M_POLC_LS1_P_MIX(4) |
+ PHY_M_POLC_IS0_P_MIX(4) |
+ PHY_M_POLC_LOS_CTRL(2) |
+ PHY_M_POLC_INIT_CTRL(2) |
+ PHY_M_POLC_STA1_CTRL(2) |
+ PHY_M_POLC_STA0_CTRL(2)));
+
+ /* restore page register */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
+ break;
+
+ default:
+ /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
+ ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
+ /* turn off the Rx LED (LED_RX) */
+ ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
+ }
+
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+
+ if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
+ /* turn on 100 Mbps LED (LED_LINK100) */
+ ledover |= PHY_M_LED_MO_100(MO_LED_ON);
+ }
+
+ if (ledover)
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+
+ /* Enable phy interrupt on auto-negotiation complete (or link up) */
+ if (sky2->autoneg == AUTONEG_ENABLE)
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
+ else
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
+}
+
+static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
+{
+ struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
+ u16 reg;
+ int i;
+ const u8 *addr = hw->dev[port]->dev_addr;
+
+ sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
+ sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
+
+ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
+
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 && port == 1) {
+ /* WA DEV_472 -- looks like crossed wires on port 2 */
+ /* clear GMAC 1 Control reset */
+ sky2_write8(hw, SK_REG(0, GMAC_CTRL), GMC_RST_CLR);
+ do {
+ sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET);
+ sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR);
+ } while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL ||
+ gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 ||
+ gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0);
+ }
+
+ if (sky2->autoneg == AUTONEG_DISABLE) {
+ reg = gma_read16(hw, port, GM_GP_CTRL);
+ reg |= GM_GPCR_AU_ALL_DIS;
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+ gma_read16(hw, port, GM_GP_CTRL);
+
+ switch (sky2->speed) {
+ case SPEED_1000:
+ reg |= GM_GPCR_SPEED_1000;
+ /* fallthru */
+ case SPEED_100:
+ reg |= GM_GPCR_SPEED_100;
+ }
+
+ if (sky2->duplex == DUPLEX_FULL)
+ reg |= GM_GPCR_DUP_FULL;
+ } else
+ reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
+
+ if (!sky2->tx_pause && !sky2->rx_pause) {
+ sky2_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
+ reg |=
+ GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ } else if (sky2->tx_pause && !sky2->rx_pause) {
+ /* disable Rx flow-control */
+ reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ }
+
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+
+ sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
+
+ spin_lock_bh(&hw->phy_lock);
+ sky2_phy_init(hw, port);
+ spin_unlock_bh(&hw->phy_lock);
+
+ /* MIB clear */
+ reg = gma_read16(hw, port, GM_PHY_ADDR);
+ gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR);
+
+ for (i = 0; i < GM_MIB_CNT_SIZE; i++)
+ gma_read16(hw, port, GM_MIB_CNT_BASE + 8 * i);
+ gma_write16(hw, port, GM_PHY_ADDR, reg);
+
+ /* transmit control */
+ gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF));
+
+ /* receive control reg: unicast + multicast + no FCS */
+ gma_write16(hw, port, GM_RX_CTRL,
+ GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA);
+
+ /* transmit flow control */
+ gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff);
+
+ /* transmit parameter */
+ gma_write16(hw, port, GM_TX_PARAM,
+ TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) |
+ TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) |
+ TX_IPG_JAM_DATA(TX_IPG_JAM_DEF) |
+ TX_BACK_OFF_LIM(TX_BOF_LIM_DEF));
+
+ /* serial mode register */
+ reg = DATA_BLIND_VAL(DATA_BLIND_DEF) |
+ GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
+
+ if (hw->dev[port]->mtu > ETH_DATA_LEN)
+ reg |= GM_SMOD_JUMBO_ENA;
+
+ gma_write16(hw, port, GM_SERIAL_MODE, reg);
+
+ /* virtual address for data */
+ gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr);
+
+ /* physical address: used for pause frames */
+ gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr);
+
+ /* ignore counter overflows */
+ gma_write16(hw, port, GM_TX_IRQ_MSK, 0);
+ gma_write16(hw, port, GM_RX_IRQ_MSK, 0);
+ gma_write16(hw, port, GM_TR_IRQ_MSK, 0);
+
+ /* Configure Rx MAC FIFO */
+ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
+ sky2_write16(hw, SK_REG(port, RX_GMF_CTRL_T),
+ GMF_RX_CTRL_DEF);
+
+ /* Flush Rx MAC FIFO on any flow control or error */
+ reg = GMR_FS_ANY_ERR;
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev <= 1)
+ reg = 0; /* WA dev #4.115 */
+
+ sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), reg);
+ /* Set threshold to 0xa (64 bytes)
+ * ASF disabled so no need to do WA dev #4.30
+ */
+ sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
+
+ /* Configure Tx MAC FIFO */
+ sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
+ sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
+}
+
+static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, size_t len)
+{
+ u32 end;
+
+ start /= 8;
+ len /= 8;
+ end = start + len - 1;
+
+ sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
+ sky2_write32(hw, RB_ADDR(q, RB_START), start);
+ sky2_write32(hw, RB_ADDR(q, RB_END), end);
+ sky2_write32(hw, RB_ADDR(q, RB_WP), start);
+ sky2_write32(hw, RB_ADDR(q, RB_RP), start);
+
+ if (q == Q_R1 || q == Q_R2) {
+ u32 rxup, rxlo;
+
+ rxlo = len/2;
+ rxup = rxlo + len/4;
+
+ /* Set thresholds on receive queue's */
+ sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), rxup);
+ sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), rxlo);
+ } else {
+ /* Enable store & forward on Tx queue's because
+ * Tx FIFO is only 1K on Yukon
+ */
+ sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD);
+ }
+
+ sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD);
+ sky2_read8(hw, RB_ADDR(q, RB_CTRL));
+}
+
+/* Setup Bus Memory Interface */
+static void sky2_qset(struct sky2_hw *hw, u16 q, u32 wm)
+{
+ sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_RESET);
+ sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_OPER_INIT);
+ sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_FIFO_OP_ON);
+ sky2_write32(hw, Q_ADDR(q, Q_WM), wm);
+}
+
+/* Setup prefetch unit registers. This is the interface between
+ * hardware and driver list elements
+ */
+static inline void sky2_prefetch_init(struct sky2_hw *hw, u32 qaddr,
+ u64 addr, u32 last)
+{
+ sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
+ sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_CLR);
+ sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_HI), addr >> 32);
+ sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_LO), (u32) addr);
+ sky2_write16(hw, Y2_QADDR(qaddr, PREF_UNIT_LAST_IDX), last);
+ sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_OP_ON);
+
+ sky2_read32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL));
+}
+
+static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2)
+{
+ struct sky2_tx_le *le = sky2->tx_le + sky2->tx_prod;
+
+ sky2->tx_prod = (sky2->tx_prod + 1) % TX_RING_SIZE;
+ return le;
+}
+
+/*
+ * This is a workaround code taken from SysKonnect sk98lin driver
+ * to deal with chip bug on Yukon EC rev 0 in the wraparound case.
+ */
+static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q,
+ u16 idx, u16 *last, u16 size)
+{
+ if (is_ec_a1(hw) && idx < *last) {
+ u16 hwget = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_GET_IDX));
+
+ if (hwget == 0) {
+ /* Start prefetching again */
+ sky2_write8(hw, Y2_QADDR(q, PREF_UNIT_FIFO_WM), 0xe0);
+ goto setnew;
+ }
+
+ if (hwget == size - 1) {
+ /* set watermark to one list element */
+ sky2_write8(hw, Y2_QADDR(q, PREF_UNIT_FIFO_WM), 8);
+
+ /* set put index to first list element */
+ sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), 0);
+ } else /* have hardware go to end of list */
+ sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX),
+ size - 1);
+ } else {
+setnew:
+ sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx);
+ }
+ *last = idx;
+}
+
+
+static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2)
+{
+ struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put;
+ sky2->rx_put = (sky2->rx_put + 1) % RX_LE_SIZE;
+ return le;
+}
+
+/* Build description to hardware about buffer */
+static inline void sky2_rx_add(struct sky2_port *sky2, struct ring_info *re)
+{
+ struct sky2_rx_le *le;
+ u32 hi = (re->mapaddr >> 16) >> 16;
+
+ re->idx = sky2->rx_put;
+ if (sky2->rx_addr64 != hi) {
+ le = sky2_next_rx(sky2);
+ le->addr = cpu_to_le32(hi);
+ le->ctrl = 0;
+ le->opcode = OP_ADDR64 | HW_OWNER;
+ sky2->rx_addr64 = hi;
+ }
+
+ le = sky2_next_rx(sky2);
+ le->addr = cpu_to_le32((u32) re->mapaddr);
+ le->length = cpu_to_le16(re->maplen);
+ le->ctrl = 0;
+ le->opcode = OP_PACKET | HW_OWNER;
+}
+
+
+/* Tell chip where to start receive checksum.
+ * Actually has two checksums, but set both same to avoid possible byte
+ * order problems.
+ */
+static void rx_set_checksum(struct sky2_port *sky2)
+{
+ struct sky2_rx_le *le;
+
+ le = sky2_next_rx(sky2);
+ le->addr = (ETH_HLEN << 16) | ETH_HLEN;
+ le->ctrl = 0;
+ le->opcode = OP_TCPSTART | HW_OWNER;
+
+ sky2_write32(sky2->hw,
+ Q_ADDR(rxqaddr[sky2->port], Q_CSR),
+ sky2->rx_csum ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
+
+}
+
+/*
+ * The RX Stop command will not work for Yukon-2 if the BMU does not
+ * reach the end of packet and since we can't make sure that we have
+ * incoming data, we must reset the BMU while it is not doing a DMA
+ * transfer. Since it is possible that the RX path is still active,
+ * the RX RAM buffer will be stopped first, so any possible incoming
+ * data will not trigger a DMA. After the RAM buffer is stopped, the
+ * BMU is polled until any DMA in progress is ended and only then it
+ * will be reset.
+ */
+static void sky2_rx_stop(struct sky2_port *sky2)
+{
+ struct sky2_hw *hw = sky2->hw;
+ unsigned rxq = rxqaddr[sky2->port];
+ int i;
+
+ /* disable the RAM Buffer receive queue */
+ sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_DIS_OP_MD);
+
+ for (i = 0; i < 0xffff; i++)
+ if (sky2_read8(hw, RB_ADDR(rxq, Q_RSL))
+ == sky2_read8(hw, RB_ADDR(rxq, Q_RL)))
+ goto stopped;
+
+ printk(KERN_WARNING PFX "%s: receiver stop failed\n",
+ sky2->netdev->name);
+stopped:
+ sky2_write32(hw, Q_ADDR(rxq, Q_CSR), BMU_RST_SET | BMU_FIFO_RST);
+
+ /* reset the Rx prefetch unit */
+ sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
+}
+
+/* Clean out receive buffer area, assumes receiver hardware stopped */
+static void sky2_rx_clean(struct sky2_port *sky2)
+{
+ unsigned i;
+
+ memset(sky2->rx_le, 0, RX_LE_BYTES);
+ for (i = 0; i < sky2->rx_pending; i++) {
+ struct ring_info *re = sky2->rx_ring + i;
+
+ if (re->skb) {
+ pci_unmap_single(sky2->hw->pdev,
+ re->mapaddr, re->maplen,
+ PCI_DMA_FROMDEVICE);
+ kfree_skb(re->skb);
+ re->skb = NULL;
+ }
+ }
+}
+
+#ifdef SKY2_VLAN_TAG_USED
+static void sky2_vlan_rx_register(struct net_device *dev, struct vlan_group *grp)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ u16 port = sky2->port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&sky2->tx_lock, flags);
+
+ sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_ON);
+ sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_ON);
+ sky2->vlgrp = grp;
+
+ spin_unlock_irqrestore(&sky2->tx_lock, flags);
+}
+
+static void sky2_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ u16 port = sky2->port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&sky2->tx_lock, flags);
+
+ sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_OFF);
+ sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_OFF);
+ if (sky2->vlgrp)
+ sky2->vlgrp->vlan_devices[vid] = NULL;
+
+ spin_unlock_irqrestore(&sky2->tx_lock, flags);
+}
+#endif
+
+#define roundup(x, y) ((((x)+((y)-1))/(y))*(y))
+static inline unsigned rx_size(const struct sky2_port *sky2)
+{
+ return roundup(sky2->netdev->mtu + ETH_HLEN + 4, 8);
+}
+
+/*
+ * Allocate and setup receiver buffer pool.
+ * In case of 64 bit dma, there are 2X as many list elements
+ * available as ring entries
+ * and need to reserve one list element so we don't wrap around.
+ *
+ * It appears the hardware has a bug in the FIFO logic that
+ * cause it to hang if the FIFO gets overrun and the receive buffer
+ * is not aligned. This means we can't use skb_reserve to align
+ * the IP header.
+ */
+static int sky2_rx_start(struct sky2_port *sky2)
+{
+ struct sky2_hw *hw = sky2->hw;
+ unsigned size = rx_size(sky2);
+ unsigned rxq = rxqaddr[sky2->port];
+ int i;
+
+ sky2->rx_put = sky2->rx_next = 0;
+ sky2_qset(hw, rxq, is_pciex(hw) ? 0x80 : 0x600);
+ sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
+
+ rx_set_checksum(sky2);
+ for (i = 0; i < sky2->rx_pending; i++) {
+ struct ring_info *re = sky2->rx_ring + i;
+
+ re->skb = dev_alloc_skb(size);
+ if (!re->skb)
+ goto nomem;
+
+ re->mapaddr = pci_map_single(hw->pdev, re->skb->data,
+ size, PCI_DMA_FROMDEVICE);
+ re->maplen = size;
+ sky2_rx_add(sky2, re);
+ }
+
+ /* Tell chip about available buffers */
+ sky2_write16(hw, Y2_QADDR(rxq, PREF_UNIT_PUT_IDX), sky2->rx_put);
+ sky2->rx_last_put = sky2_read16(hw, Y2_QADDR(rxq, PREF_UNIT_PUT_IDX));
+ return 0;
+nomem:
+ sky2_rx_clean(sky2);
+ return -ENOMEM;
+}
+
+/* Bring up network interface. */
+static int sky2_up(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ u32 ramsize, rxspace;
+ int err = -ENOMEM;
+
+ if (netif_msg_ifup(sky2))
+ printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
+
+ /* must be power of 2 */
+ sky2->tx_le = pci_alloc_consistent(hw->pdev,
+ TX_RING_SIZE *
+ sizeof(struct sky2_tx_le),
+ &sky2->tx_le_map);
+ if (!sky2->tx_le)
+ goto err_out;
+
+ sky2->tx_ring = kzalloc(TX_RING_SIZE * sizeof(struct ring_info),
+ GFP_KERNEL);
+ if (!sky2->tx_ring)
+ goto err_out;
+ sky2->tx_prod = sky2->tx_cons = 0;
+
+ sky2->rx_le = pci_alloc_consistent(hw->pdev, RX_LE_BYTES,
+ &sky2->rx_le_map);
+ if (!sky2->rx_le)
+ goto err_out;
+ memset(sky2->rx_le, 0, RX_LE_BYTES);
+
+ sky2->rx_ring = kzalloc(sky2->rx_pending * sizeof(struct ring_info),
+ GFP_KERNEL);
+ if (!sky2->rx_ring)
+ goto err_out;
+
+ sky2_mac_init(hw, port);
+
+ /* Configure RAM buffers */
+ if (hw->chip_id == CHIP_ID_YUKON_FE ||
+ (hw->chip_id == CHIP_ID_YUKON_EC && hw->chip_rev == 2))
+ ramsize = 4096;
+ else {
+ u8 e0 = sky2_read8(hw, B2_E_0);
+ ramsize = (e0 == 0) ? (128 * 1024) : (e0 * 4096);
+ }
+
+ /* 2/3 for Rx */
+ rxspace = (2 * ramsize) / 3;
+ sky2_ramset(hw, rxqaddr[port], 0, rxspace);
+ sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace);
+
+ /* Make sure SyncQ is disabled */
+ sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
+ RB_RST_SET);
+
+ sky2_qset(hw, txqaddr[port], 0x600);
+ sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
+ TX_RING_SIZE - 1);
+
+ err = sky2_rx_start(sky2);
+ if (err)
+ goto err_out;
+
+ /* Enable interrupts from phy/mac for port */
+ hw->intr_mask |= (port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2;
+ sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ return 0;
+
+err_out:
+ if (sky2->rx_le)
+ pci_free_consistent(hw->pdev, RX_LE_BYTES,
+ sky2->rx_le, sky2->rx_le_map);
+ if (sky2->tx_le)
+ pci_free_consistent(hw->pdev,
+ TX_RING_SIZE * sizeof(struct sky2_tx_le),
+ sky2->tx_le, sky2->tx_le_map);
+ if (sky2->tx_ring)
+ kfree(sky2->tx_ring);
+ if (sky2->rx_ring)
+ kfree(sky2->rx_ring);
+
+ return err;
+}
+
+/* Modular subtraction in ring */
+static inline int tx_dist(unsigned tail, unsigned head)
+{
+ return (head >= tail ? head : head + TX_RING_SIZE) - tail;
+}
+
+/* Number of list elements available for next tx */
+static inline int tx_avail(const struct sky2_port *sky2)
+{
+ return sky2->tx_pending - tx_dist(sky2->tx_cons, sky2->tx_prod);
+}
+
+/* Estimate of number of transmit list elements required */
+static inline unsigned tx_le_req(const struct sk_buff *skb)
+{
+ unsigned count;
+
+ count = sizeof(dma_addr_t) / sizeof(u32);
+ count += skb_shinfo(skb)->nr_frags * count;
+
+ if (skb_shinfo(skb)->tso_size)
+ ++count;
+
+ if (skb->ip_summed)
+ ++count;
+
+ return count;
+}
+
+/*
+ * Put one packet in ring for transmit.
+ * A single packet can generate multiple list elements, and
+ * the number of ring elements will probably be less than the number
+ * of list elements used.
+ */
+static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ struct sky2_tx_le *le = NULL;
+ struct ring_info *re;
+ unsigned long flags;
+ unsigned i, len;
+ dma_addr_t mapping;
+ u32 addr64;
+ u16 mss;
+ u8 ctrl;
+
+ local_irq_save(flags);
+ if (!spin_trylock(&sky2->tx_lock)) {
+ local_irq_restore(flags);
+ return NETDEV_TX_LOCKED;
+ }
+
+ if (unlikely(tx_avail(sky2) < tx_le_req(skb))) {
+ netif_stop_queue(dev);
+ spin_unlock_irqrestore(&sky2->tx_lock, flags);
+
+ printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
+ dev->name);
+ return NETDEV_TX_BUSY;
+ }
+
+ if (unlikely(netif_msg_tx_queued(sky2)))
+ printk(KERN_DEBUG "%s: tx queued, slot %u, len %d\n",
+ dev->name, sky2->tx_prod, skb->len);
+
+ len = skb_headlen(skb);
+ mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
+ addr64 = (mapping >> 16) >> 16;
+
+ re = sky2->tx_ring + sky2->tx_prod;
+
+ /* Send high bits if changed */
+ if (addr64 != sky2->tx_addr64) {
+ le = get_tx_le(sky2);
+ le->tx.addr = cpu_to_le32(addr64);
+ le->ctrl = 0;
+ le->opcode = OP_ADDR64 | HW_OWNER;
+ sky2->tx_addr64 = addr64;
+ }
+
+ /* Check for TCP Segmentation Offload */
+ mss = skb_shinfo(skb)->tso_size;
+ if (mss != 0) {
+ /* just drop the packet if non-linear expansion fails */
+ if (skb_header_cloned(skb) &&
+ pskb_expand_head(skb, 0, 0, GFP_ATOMIC)) {
+ dev_kfree_skb_any(skb);
+ goto out_unlock;
+ }
+
+ mss += ((skb->h.th->doff - 5) * 4); /* TCP options */
+ mss += (skb->nh.iph->ihl * 4) + sizeof(struct tcphdr);
+ mss += ETH_HLEN;
+ }
+
+ if (mss != sky2->tx_last_mss) {
+ le = get_tx_le(sky2);
+ le->tx.tso.size = cpu_to_le16(mss);
+ le->tx.tso.rsvd = 0;
+ le->opcode = OP_LRGLEN | HW_OWNER;
+ le->ctrl = 0;
+ sky2->tx_last_mss = mss;
+ }
+
+ ctrl = 0;
+#ifdef SKY2_VLAN_TAG_USED
+ /* Add VLAN tag, can piggyback on LRGLEN or ADDR64 */
+ if (sky2->vlgrp && vlan_tx_tag_present(skb)) {
+ if (!le) {
+ le = get_tx_le(sky2);
+ le->tx.addr = 0;
+ le->opcode = OP_VLAN|HW_OWNER;
+ le->ctrl = 0;
+ } else
+ le->opcode |= OP_VLAN;
+ le->length = cpu_to_be16(vlan_tx_tag_get(skb));
+ ctrl |= INS_VLAN;
+ }
+#endif
+
+ /* Handle TCP checksum offload */
+ if (skb->ip_summed == CHECKSUM_HW) {
+ u16 hdr = skb->h.raw - skb->data;
+ u16 offset = hdr + skb->csum;
+
+ ctrl = CALSUM | WR_SUM | INIT_SUM | LOCK_SUM;
+ if (skb->nh.iph->protocol == IPPROTO_UDP)
+ ctrl |= UDPTCP;
+
+ le = get_tx_le(sky2);
+ le->tx.csum.start = cpu_to_le16(hdr);
+ le->tx.csum.offset = cpu_to_le16(offset);
+ le->length = 0; /* initial checksum value */
+ le->ctrl = 1; /* one packet */
+ le->opcode = OP_TCPLISW | HW_OWNER;
+ }
+
+ le = get_tx_le(sky2);
+ le->tx.addr = cpu_to_le32((u32) mapping);
+ le->length = cpu_to_le16(len);
+ le->ctrl = ctrl;
+ le->opcode = mss ? (OP_LARGESEND | HW_OWNER) : (OP_PACKET | HW_OWNER);
+
+ /* Record the transmit mapping info */
+ re->skb = skb;
+ re->mapaddr = mapping;
+ re->maplen = len;
+
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+ struct ring_info *fre;
+
+ mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset,
+ frag->size, PCI_DMA_TODEVICE);
+ addr64 = (mapping >> 16) >> 16;
+ if (addr64 != sky2->tx_addr64) {
+ le = get_tx_le(sky2);
+ le->tx.addr = cpu_to_le32(addr64);
+ le->ctrl = 0;
+ le->opcode = OP_ADDR64 | HW_OWNER;
+ sky2->tx_addr64 = addr64;
+ }
+
+ le = get_tx_le(sky2);
+ le->tx.addr = cpu_to_le32((u32) mapping);
+ le->length = cpu_to_le16(frag->size);
+ le->ctrl = ctrl;
+ le->opcode = OP_BUFFER | HW_OWNER;
+
+ fre = sky2->tx_ring
+ + ((re - sky2->tx_ring) + i + 1) % TX_RING_SIZE;
+ fre->skb = NULL;
+ fre->mapaddr = mapping;
+ fre->maplen = frag->size;
+ }
+ re->idx = sky2->tx_prod;
+ le->ctrl |= EOP;
+
+ sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod,
+ &sky2->tx_last_put, TX_RING_SIZE);
+
+ if (tx_avail(sky2) < MAX_SKB_TX_LE + 1)
+ netif_stop_queue(dev);
+
+out_unlock:
+ mmiowb();
+ spin_unlock_irqrestore(&sky2->tx_lock, flags);
+
+ dev->trans_start = jiffies;
+ return NETDEV_TX_OK;
+}
+
+/*
+ * Free ring elements from starting at tx_cons until "done"
+ *
+ * NB: the hardware will tell us about partial completion of multi-part
+ * buffers; these are deferred until completion.
+ */
+static void sky2_tx_complete(struct sky2_port *sky2, u16 done)
+{
+ struct net_device *dev = sky2->netdev;
+ unsigned i;
+
+ if (unlikely(netif_msg_tx_done(sky2)))
+ printk(KERN_DEBUG "%s: tx done, up to %u\n",
+ dev->name, done);
+
+ spin_lock(&sky2->tx_lock);
+
+ while (sky2->tx_cons != done) {
+ struct ring_info *re = sky2->tx_ring + sky2->tx_cons;
+ struct sk_buff *skb;
+
+ /* Check for partial status */
+ if (tx_dist(sky2->tx_cons, done)
+ < tx_dist(sky2->tx_cons, re->idx))
+ goto out;
+
+ skb = re->skb;
+ pci_unmap_single(sky2->hw->pdev,
+ re->mapaddr, re->maplen, PCI_DMA_TODEVICE);
+
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ struct ring_info *fre;
+ fre =
+ sky2->tx_ring + (sky2->tx_cons + i +
+ 1) % TX_RING_SIZE;
+ pci_unmap_page(sky2->hw->pdev, fre->mapaddr,
+ fre->maplen, PCI_DMA_TODEVICE);
+ }
+
+ dev_kfree_skb_any(skb);
+
+ sky2->tx_cons = re->idx;
+ }
+out:
+
+ if (netif_queue_stopped(dev) && tx_avail(sky2) > MAX_SKB_TX_LE)
+ netif_wake_queue(dev);
+ spin_unlock(&sky2->tx_lock);
+}
+
+/* Cleanup all untransmitted buffers, assume transmitter not running */
+static inline void sky2_tx_clean(struct sky2_port *sky2)
+{
+ sky2_tx_complete(sky2, sky2->tx_prod);
+}
+
+/* Network shutdown */
+static int sky2_down(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ u16 ctrl;
+
+ if (netif_msg_ifdown(sky2))
+ printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
+
+ netif_stop_queue(dev);
+
+ sky2_phy_reset(hw, port);
+
+ /* Stop transmitter */
+ sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP);
+ sky2_read32(hw, Q_ADDR(txqaddr[port], Q_CSR));
+
+ sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
+ RB_RST_SET | RB_DIS_OP_MD);
+
+ ctrl = gma_read16(hw, port, GM_GP_CTRL);
+ ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA);
+ gma_write16(hw, port, GM_GP_CTRL, ctrl);
+
+ sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
+
+ /* Workaround shared GMAC reset */
+ if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
+ && port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
+ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
+
+ /* Disable Force Sync bit and Enable Alloc bit */
+ sky2_write8(hw, SK_REG(port, TXA_CTRL),
+ TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC);
+
+ /* Stop Interval Timer and Limit Counter of Tx Arbiter */
+ sky2_write32(hw, SK_REG(port, TXA_ITI_INI), 0L);
+ sky2_write32(hw, SK_REG(port, TXA_LIM_INI), 0L);
+
+ /* Reset the PCI FIFO of the async Tx queue */
+ sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR),
+ BMU_RST_SET | BMU_FIFO_RST);
+
+ /* Reset the Tx prefetch units */
+ sky2_write32(hw, Y2_QADDR(txqaddr[port], PREF_UNIT_CTRL),
+ PREF_UNIT_RST_SET);
+
+ sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET);
+
+ sky2_rx_stop(sky2);
+
+ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
+ sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
+
+ /* turn off LED's */
+ sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
+
+ sky2_tx_clean(sky2);
+ sky2_rx_clean(sky2);
+
+ pci_free_consistent(hw->pdev, RX_LE_BYTES,
+ sky2->rx_le, sky2->rx_le_map);
+ kfree(sky2->rx_ring);
+
+ pci_free_consistent(hw->pdev,
+ TX_RING_SIZE * sizeof(struct sky2_tx_le),
+ sky2->tx_le, sky2->tx_le_map);
+ kfree(sky2->tx_ring);
+
+ return 0;
+}
+
+static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux)
+{
+ if (!hw->copper)
+ return SPEED_1000;
+
+ if (hw->chip_id == CHIP_ID_YUKON_FE)
+ return (aux & PHY_M_PS_SPEED_100) ? SPEED_100 : SPEED_10;
+
+ switch (aux & PHY_M_PS_SPEED_MSK) {
+ case PHY_M_PS_SPEED_1000:
+ return SPEED_1000;
+ case PHY_M_PS_SPEED_100:
+ return SPEED_100;
+ default:
+ return SPEED_10;
+ }
+}
+
+static void sky2_link_up(struct sky2_port *sky2)
+{
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ u16 reg;
+
+ /* disable Rx GMAC FIFO flush mode */
+ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RX_F_FL_OFF);
+
+ /* Enable Transmit FIFO Underrun */
+ sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
+
+ reg = gma_read16(hw, port, GM_GP_CTRL);
+ if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE)
+ reg |= GM_GPCR_DUP_FULL;
+
+ /* enable Rx/Tx */
+ reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+ gma_read16(hw, port, GM_GP_CTRL);
+
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
+
+ netif_carrier_on(sky2->netdev);
+ netif_wake_queue(sky2->netdev);
+
+ /* Turn on link LED */
+ sky2_write8(hw, SK_REG(port, LNK_LED_REG),
+ LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF);
+
+ if (hw->chip_id == CHIP_ID_YUKON_XL) {
+ u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
+ PHY_M_LEDC_INIT_CTRL(sky2->speed ==
+ SPEED_10 ? 7 : 0) |
+ PHY_M_LEDC_STA1_CTRL(sky2->speed ==
+ SPEED_100 ? 7 : 0) |
+ PHY_M_LEDC_STA0_CTRL(sky2->speed ==
+ SPEED_1000 ? 7 : 0));
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
+ }
+
+ if (netif_msg_link(sky2))
+ printk(KERN_INFO PFX
+ "%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
+ sky2->netdev->name, sky2->speed,
+ sky2->duplex == DUPLEX_FULL ? "full" : "half",
+ (sky2->tx_pause && sky2->rx_pause) ? "both" :
+ sky2->tx_pause ? "tx" : sky2->rx_pause ? "rx" : "none");
+}
+
+static void sky2_link_down(struct sky2_port *sky2)
+{
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ u16 reg;
+
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
+
+ reg = gma_read16(hw, port, GM_GP_CTRL);
+ reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+ gma_read16(hw, port, GM_GP_CTRL); /* PCI post */
+
+ if (sky2->rx_pause && !sky2->tx_pause) {
+ /* restore Asymmetric Pause bit */
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
+ gm_phy_read(hw, port, PHY_MARV_AUNE_ADV)
+ | PHY_M_AN_ASP);
+ }
+
+ sky2_phy_reset(hw, port);
+
+ netif_carrier_off(sky2->netdev);
+ netif_stop_queue(sky2->netdev);
+
+ /* Turn on link LED */
+ sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
+
+ if (netif_msg_link(sky2))
+ printk(KERN_INFO PFX "%s: Link is down.\n", sky2->netdev->name);
+ sky2_phy_init(hw, port);
+}
+
+static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux)
+{
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ u16 lpa;
+
+ lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP);
+
+ if (lpa & PHY_M_AN_RF) {
+ printk(KERN_ERR PFX "%s: remote fault", sky2->netdev->name);
+ return -1;
+ }
+
+ if (hw->chip_id != CHIP_ID_YUKON_FE &&
+ gm_phy_read(hw, port, PHY_MARV_1000T_STAT) & PHY_B_1000S_MSF) {
+ printk(KERN_ERR PFX "%s: master/slave fault",
+ sky2->netdev->name);
+ return -1;
+ }
+
+ if (!(aux & PHY_M_PS_SPDUP_RES)) {
+ printk(KERN_ERR PFX "%s: speed/duplex mismatch",
+ sky2->netdev->name);
+ return -1;
+ }
+
+ sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
+
+ sky2->speed = sky2_phy_speed(hw, aux);
+
+ /* Pause bits are offset (9..8) */
+ if (hw->chip_id == CHIP_ID_YUKON_XL)
+ aux >>= 6;
+
+ sky2->rx_pause = (aux & PHY_M_PS_RX_P_EN) != 0;
+ sky2->tx_pause = (aux & PHY_M_PS_TX_P_EN) != 0;
+
+ if ((sky2->tx_pause || sky2->rx_pause)
+ && !(sky2->speed < SPEED_1000 && sky2->duplex == DUPLEX_HALF))
+ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
+ else
+ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
+
+ return 0;
+}
+
+/*
+ * Interrupt from PHY are handled in tasklet (soft irq)
+ * because accessing phy registers requires spin wait which might
+ * cause excess interrupt latency.
+ */
+static void sky2_phy_task(unsigned long data)
+{
+ struct sky2_port *sky2 = (struct sky2_port *)data;
+ struct sky2_hw *hw = sky2->hw;
+ u16 istatus, phystat;
+
+ spin_lock(&hw->phy_lock);
+ istatus = gm_phy_read(hw, sky2->port, PHY_MARV_INT_STAT);
+ phystat = gm_phy_read(hw, sky2->port, PHY_MARV_PHY_STAT);
+
+ if (netif_msg_intr(sky2))
+ printk(KERN_INFO PFX "%s: phy interrupt status 0x%x 0x%x\n",
+ sky2->netdev->name, istatus, phystat);
+
+ if (istatus & PHY_M_IS_AN_COMPL) {
+ if (sky2_autoneg_done(sky2, phystat) == 0)
+ sky2_link_up(sky2);
+ goto out;
+ }
+
+ if (istatus & PHY_M_IS_LSP_CHANGE)
+ sky2->speed = sky2_phy_speed(hw, phystat);
+
+ if (istatus & PHY_M_IS_DUP_CHANGE)
+ sky2->duplex =
+ (phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
+
+ if (istatus & PHY_M_IS_LST_CHANGE) {
+ if (phystat & PHY_M_PS_LINK_UP)
+ sky2_link_up(sky2);
+ else
+ sky2_link_down(sky2);
+ }
+out:
+ spin_unlock(&hw->phy_lock);
+
+ local_irq_disable();
+ hw->intr_mask |= (sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2;
+ sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ local_irq_enable();
+}
+
+static void sky2_tx_timeout(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ if (netif_msg_timer(sky2))
+ printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
+
+ sky2_write32(sky2->hw, Q_ADDR(txqaddr[sky2->port], Q_CSR), BMU_STOP);
+ sky2_read32(sky2->hw, Q_ADDR(txqaddr[sky2->port], Q_CSR));
+
+ sky2_tx_clean(sky2);
+}
+
+static int sky2_change_mtu(struct net_device *dev, int new_mtu)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ int err;
+ u16 ctl, mode;
+
+ if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
+ return -EINVAL;
+
+ if (!netif_running(dev)) {
+ dev->mtu = new_mtu;
+ return 0;
+ }
+
+ local_irq_disable();
+ sky2_write32(hw, B0_IMSK, 0);
+
+ ctl = gma_read16(hw, sky2->port, GM_GP_CTRL);
+ gma_write16(hw, sky2->port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA);
+ sky2_rx_stop(sky2);
+ sky2_rx_clean(sky2);
+
+ dev->mtu = new_mtu;
+ mode = DATA_BLIND_VAL(DATA_BLIND_DEF) |
+ GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
+
+ if (dev->mtu > ETH_DATA_LEN)
+ mode |= GM_SMOD_JUMBO_ENA;
+
+ gma_write16(hw, sky2->port, GM_SERIAL_MODE, mode);
+
+ sky2_write8(hw, RB_ADDR(rxqaddr[sky2->port], RB_CTRL), RB_ENA_OP_MD);
+
+ err = sky2_rx_start(sky2);
+ gma_write16(hw, sky2->port, GM_GP_CTRL, ctl);
+
+ sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ sky2_read32(hw, B0_IMSK);
+ local_irq_enable();
+ return err;
+}
+
+/*
+ * Receive one packet.
+ * For small packets or errors, just reuse existing skb.
+ * For larger packets, get new buffer.
+ */
+static struct sk_buff *sky2_receive(struct sky2_port *sky2,
+ u16 length, u32 status)
+{
+ struct ring_info *re = sky2->rx_ring + sky2->rx_next;
+ struct sk_buff *skb = NULL;
+ struct net_device *dev;
+ const unsigned int bufsize = rx_size(sky2);
+
+ if (unlikely(netif_msg_rx_status(sky2)))
+ printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n",
+ sky2->netdev->name, sky2->rx_next, status, length);
+
+ sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending;
+
+ if (!(status & GMR_FS_RX_OK) || (status & GMR_FS_ANY_ERR))
+ goto error;
+
+ if (length < RX_COPY_THRESHOLD) {
+ skb = alloc_skb(length + 2, GFP_ATOMIC);
+ if (!skb)
+ goto resubmit;
+
+ skb_reserve(skb, 2);
+ pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->mapaddr,
+ length, PCI_DMA_FROMDEVICE);
+ memcpy(skb->data, re->skb->data, length);
+ skb->ip_summed = re->skb->ip_summed;
+ skb->csum = re->skb->csum;
+ pci_dma_sync_single_for_device(sky2->hw->pdev, re->mapaddr,
+ length, PCI_DMA_FROMDEVICE);
+ } else {
+ struct sk_buff *nskb;
+
+ nskb = dev_alloc_skb(bufsize);
+ if (!nskb)
+ goto resubmit;
+
+ skb = re->skb;
+ re->skb = nskb;
+ pci_unmap_single(sky2->hw->pdev, re->mapaddr,
+ re->maplen, PCI_DMA_FROMDEVICE);
+ prefetch(skb->data);
+
+ re->mapaddr = pci_map_single(sky2->hw->pdev, nskb->data,
+ bufsize, PCI_DMA_FROMDEVICE);
+ re->maplen = bufsize;
+ }
+
+ skb_put(skb, length);
+ dev = sky2->netdev;
+ skb->dev = dev;
+ skb->protocol = eth_type_trans(skb, dev);
+ dev->last_rx = jiffies;
+
+resubmit:
+ re->skb->ip_summed = CHECKSUM_NONE;
+ sky2_rx_add(sky2, re);
+
+ /* Tell receiver about new buffers. */
+ sky2_put_idx(sky2->hw, rxqaddr[sky2->port], sky2->rx_put,
+ &sky2->rx_last_put, RX_LE_SIZE);
+
+ return skb;
+
+error:
+ if (status & GMR_FS_GOOD_FC)
+ goto resubmit;
+
+ if (netif_msg_rx_err(sky2))
+ printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
+ sky2->netdev->name, status, length);
+
+ if (status & (GMR_FS_LONG_ERR | GMR_FS_UN_SIZE))
+ sky2->net_stats.rx_length_errors++;
+ if (status & GMR_FS_FRAGMENT)
+ sky2->net_stats.rx_frame_errors++;
+ if (status & GMR_FS_CRC_ERR)
+ sky2->net_stats.rx_crc_errors++;
+ if (status & GMR_FS_RX_FF_OV)
+ sky2->net_stats.rx_fifo_errors++;
+
+ goto resubmit;
+}
+
+/* Transmit ring index in reported status block is encoded as:
+ *
+ * | TXS2 | TXA2 | TXS1 | TXA1
+ */
+static inline u16 tx_index(u8 port, u32 status, u16 len)
+{
+ if (port == 0)
+ return status & 0xfff;
+ else
+ return ((status >> 24) & 0xff) | (len & 0xf) << 8;
+}
+
+/*
+ * Both ports share the same status interrupt, therefore there is only
+ * one poll routine.
+ */
+static int sky2_poll(struct net_device *dev0, int *budget)
+{
+ struct sky2_hw *hw = ((struct sky2_port *) netdev_priv(dev0))->hw;
+ unsigned int to_do = min(dev0->quota, *budget);
+ unsigned int work_done = 0;
+ u16 hwidx;
+
+ hwidx = sky2_read16(hw, STAT_PUT_IDX);
+ BUG_ON(hwidx >= STATUS_RING_SIZE);
+ rmb();
+
+ do {
+ struct sky2_status_le *le = hw->st_le + hw->st_idx;
+ struct sky2_port *sky2;
+ struct sk_buff *skb;
+ u32 status;
+ u16 length;
+
+ /* Are we done yet? */
+ if (hw->st_idx == hwidx) {
+ sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
+ hwidx = sky2_read16(hw, STAT_PUT_IDX);
+ if (hwidx == hw->st_idx)
+ break;
+ }
+
+ hw->st_idx = (hw->st_idx + 1) % STATUS_RING_SIZE;
+ prefetch(&hw->st_le[hw->st_idx]);
+
+ BUG_ON(le->link >= hw->ports || !hw->dev[le->link]);
+
+ sky2 = netdev_priv(hw->dev[le->link]);
+ status = le32_to_cpu(le->status);
+ length = le16_to_cpu(le->length);
+
+ switch (le->opcode & ~HW_OWNER) {
+ case OP_RXSTAT:
+ skb = sky2_receive(sky2, length, status);
+ if (!skb)
+ break;
+#ifdef SKY2_VLAN_TAG_USED
+ if (sky2->vlgrp && (status & GMR_FS_VLAN)) {
+ vlan_hwaccel_receive_skb(skb,
+ sky2->vlgrp,
+ be16_to_cpu(sky2->rx_tag));
+ } else
+#endif
+ netif_receive_skb(skb);
+ ++work_done;
+ break;
+
+#ifdef SKY2_VLAN_TAG_USED
+ case OP_RXVLAN:
+ sky2->rx_tag = length;
+ break;
+
+ case OP_RXCHKSVLAN:
+ sky2->rx_tag = length;
+ /* fall through */
+#endif
+ case OP_RXCHKS:
+ skb = sky2->rx_ring[sky2->rx_next].skb;
+ skb->ip_summed = CHECKSUM_HW;
+ skb->csum = le16_to_cpu(status);
+ break;
+
+ case OP_TXINDEXLE:
+ sky2_tx_complete(sky2,
+ tx_index(sky2->port, status, length));
+ break;
+
+ default:
+ if (net_ratelimit())
+ printk(KERN_WARNING PFX
+ "unknown status opcode 0x%x\n",
+ le->opcode);
+ break;
+ }
+
+ le->opcode = 0; /* paranoia */
+ } while (work_done < to_do);
+
+ mmiowb();
+
+ *budget -= work_done;
+ dev0->quota -= work_done;
+ if (work_done < to_do) {
+ /*
+ * Another chip workaround, need to restart TX timer if status
+ * LE was handled. WA_DEV_43_418
+ */
+ if (is_ec_a1(hw)) {
+ sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
+ sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
+ }
+
+ netif_rx_complete(dev0);
+ hw->intr_mask |= Y2_IS_STAT_BMU;
+ sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ sky2_read32(hw, B0_IMSK);
+ }
+
+ return work_done >= to_do;
+
+}
+
+static void sky2_hw_error(struct sky2_hw *hw, unsigned port, u32 status)
+{
+ struct net_device *dev = hw->dev[port];
+
+ printk(KERN_INFO PFX "%s: hw error interrupt status 0x%x\n",
+ dev->name, status);
+
+ if (status & Y2_IS_PAR_RD1) {
+ printk(KERN_ERR PFX "%s: ram data read parity error\n",
+ dev->name);
+ /* Clear IRQ */
+ sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR);
+ }
+
+ if (status & Y2_IS_PAR_WR1) {
+ printk(KERN_ERR PFX "%s: ram data write parity error\n",
+ dev->name);
+
+ sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR);
+ }
+
+ if (status & Y2_IS_PAR_MAC1) {
+ printk(KERN_ERR PFX "%s: MAC parity error\n", dev->name);
+ sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE);
+ }
+
+ if (status & Y2_IS_PAR_RX1) {
+ printk(KERN_ERR PFX "%s: RX parity error\n", dev->name);
+ sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR);
+ }
+
+ if (status & Y2_IS_TCP_TXA1) {
+ printk(KERN_ERR PFX "%s: TCP segmentation error\n", dev->name);
+ sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP);
+ }
+}
+
+static void sky2_hw_intr(struct sky2_hw *hw)
+{
+ u32 status = sky2_read32(hw, B0_HWE_ISRC);
+
+ if (status & Y2_IS_TIST_OV)
+ sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
+
+ if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
+ u16 pci_err;
+
+ pci_read_config_word(hw->pdev, PCI_STATUS, &pci_err);
+ printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
+ pci_name(hw->pdev), pci_err);
+
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_write_config_word(hw->pdev, PCI_STATUS,
+ pci_err | PCI_STATUS_ERROR_BITS);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+ }
+
+ if (status & Y2_IS_PCI_EXP) {
+ /* PCI-Express uncorrectable Error occurred */
+ u32 pex_err;
+
+ pci_read_config_dword(hw->pdev, PEX_UNC_ERR_STAT, &pex_err);
+
+ printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
+ pci_name(hw->pdev), pex_err);
+
+ /* clear the interrupt */
+ sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
+ 0xffffffffUL);
+ sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+ if (pex_err & PEX_FATAL_ERRORS) {
+ u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK);
+ hwmsk &= ~Y2_IS_PCI_EXP;
+ sky2_write32(hw, B0_HWE_IMSK, hwmsk);
+ }
+ }
+
+ if (status & Y2_HWE_L1_MASK)
+ sky2_hw_error(hw, 0, status);
+ status >>= 8;
+ if (status & Y2_HWE_L1_MASK)
+ sky2_hw_error(hw, 1, status);
+}
+
+static void sky2_mac_intr(struct sky2_hw *hw, unsigned port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct sky2_port *sky2 = netdev_priv(dev);
+ u8 status = sky2_read8(hw, SK_REG(port, GMAC_IRQ_SRC));
+
+ if (netif_msg_intr(sky2))
+ printk(KERN_INFO PFX "%s: mac interrupt status 0x%x\n",
+ dev->name, status);
+
+ if (status & GM_IS_RX_FF_OR) {
+ ++sky2->net_stats.rx_fifo_errors;
+ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO);
+ }
+
+ if (status & GM_IS_TX_FF_UR) {
+ ++sky2->net_stats.tx_fifo_errors;
+ sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU);
+ }
+}
+
+static void sky2_phy_intr(struct sky2_hw *hw, unsigned port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ hw->intr_mask &= ~(port == 0 ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
+ sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ tasklet_schedule(&sky2->phy_task);
+}
+
+static irqreturn_t sky2_intr(int irq, void *dev_id, struct pt_regs *regs)
+{
+ struct sky2_hw *hw = dev_id;
+ struct net_device *dev0 = hw->dev[0];
+ u32 status;
+
+ status = sky2_read32(hw, B0_Y2_SP_ISRC2);
+ if (status == 0 || status == ~0)
+ return IRQ_NONE;
+
+ if (status & Y2_IS_HW_ERR)
+ sky2_hw_intr(hw);
+
+ /* Do NAPI for Rx and Tx status */
+ if (status & Y2_IS_STAT_BMU) {
+ hw->intr_mask &= ~Y2_IS_STAT_BMU;
+ sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ prefetch(&hw->st_le[hw->st_idx]);
+
+ if (netif_rx_schedule_test(dev0))
+ __netif_rx_schedule(dev0);
+ }
+
+ if (status & Y2_IS_IRQ_PHY1)
+ sky2_phy_intr(hw, 0);
+
+ if (status & Y2_IS_IRQ_PHY2)
+ sky2_phy_intr(hw, 1);
+
+ if (status & Y2_IS_IRQ_MAC1)
+ sky2_mac_intr(hw, 0);
+
+ if (status & Y2_IS_IRQ_MAC2)
+ sky2_mac_intr(hw, 1);
+
+ sky2_write32(hw, B0_Y2_SP_ICR, 2);
+
+ sky2_read32(hw, B0_IMSK);
+
+ return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void sky2_netpoll(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ sky2_intr(sky2->hw->pdev->irq, sky2->hw, NULL);
+}
+#endif
+
+/* Chip internal frequency for clock calculations */
+static inline u32 sky2_khz(const struct sky2_hw *hw)
+{
+ switch (hw->chip_id) {
+ case CHIP_ID_YUKON_EC:
+ return 125000; /* 125 Mhz */
+ case CHIP_ID_YUKON_FE:
+ return 100000; /* 100 Mhz */
+ default: /* YUKON_XL */
+ return 156000; /* 156 Mhz */
+ }
+}
+
+static inline u32 sky2_ms2clk(const struct sky2_hw *hw, u32 ms)
+{
+ return sky2_khz(hw) * ms;
+}
+
+static inline u32 sky2_us2clk(const struct sky2_hw *hw, u32 us)
+{
+ return (sky2_khz(hw) * us) / 1000;
+}
+
+static int sky2_reset(struct sky2_hw *hw)
+{
+ u32 ctst;
+ u16 status;
+ u8 t8, pmd_type;
+ int i;
+
+ ctst = sky2_read32(hw, B0_CTST);
+
+ sky2_write8(hw, B0_CTST, CS_RST_CLR);
+ hw->chip_id = sky2_read8(hw, B2_CHIP_ID);
+ if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) {
+ printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
+ pci_name(hw->pdev), hw->chip_id);
+ return -EOPNOTSUPP;
+ }
+
+ /* ring for status responses */
+ hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
+ &hw->st_dma);
+ if (!hw->st_le)
+ return -ENOMEM;
+
+ /* disable ASF */
+ if (hw->chip_id <= CHIP_ID_YUKON_EC) {
+ sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
+ sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE);
+ }
+
+ /* do a SW reset */
+ sky2_write8(hw, B0_CTST, CS_RST_SET);
+ sky2_write8(hw, B0_CTST, CS_RST_CLR);
+
+ /* clear PCI errors, if any */
+ pci_read_config_word(hw->pdev, PCI_STATUS, &status);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_write_config_word(hw->pdev, PCI_STATUS,
+ status | PCI_STATUS_ERROR_BITS);
+
+ sky2_write8(hw, B0_CTST, CS_MRST_CLR);
+
+ /* clear any PEX errors */
+ if (is_pciex(hw)) {
+ u16 lstat;
+ pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
+ 0xffffffffUL);
+ pci_read_config_word(hw->pdev, PEX_LNK_STAT, &lstat);
+ }
+
+ pmd_type = sky2_read8(hw, B2_PMD_TYP);
+ hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
+
+ hw->ports = 1;
+ t8 = sky2_read8(hw, B2_Y2_HW_RES);
+ if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
+ if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC))
+ ++hw->ports;
+ }
+ hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4;
+
+ sky2_set_power_state(hw, PCI_D0);
+
+ for (i = 0; i < hw->ports; i++) {
+ sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
+ sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
+ }
+
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+ /* Clear I2C IRQ noise */
+ sky2_write32(hw, B2_I2C_IRQ, 1);
+
+ /* turn off hardware timer (unused) */
+ sky2_write8(hw, B2_TI_CTRL, TIM_STOP);
+ sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ);
+
+ sky2_write8(hw, B0_Y2LED, LED_STAT_ON);
+
+ /* Turn on descriptor polling (every 75us) */
+ sky2_write32(hw, B28_DPT_INI, sky2_us2clk(hw, 75));
+ sky2_write8(hw, B28_DPT_CTRL, DPT_START);
+
+ /* Turn off receive timestamp */
+ sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_STOP);
+ sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
+
+ /* enable the Tx Arbiters */
+ for (i = 0; i < hw->ports; i++)
+ sky2_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB);
+
+ /* Initialize ram interface */
+ for (i = 0; i < hw->ports; i++) {
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_CTRL), RI_RST_CLR);
+
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R1), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA1), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS1), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R1), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA1), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS1), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R2), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA2), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS2), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R2), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA2), SK_RI_TO_53);
+ sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS2), SK_RI_TO_53);
+ }
+
+ if (is_pciex(hw)) {
+ u16 pctrl;
+
+ /* change Max. Read Request Size to 2048 bytes */
+ pci_read_config_word(hw->pdev, PEX_DEV_CTRL, &pctrl);
+ pctrl &= ~PEX_DC_MAX_RRS_MSK;
+ pctrl |= PEX_DC_MAX_RD_RQ_SIZE(4);
+
+
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_write_config_word(hw->pdev, PEX_DEV_CTRL, pctrl);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+ }
+
+ sky2_write32(hw, B0_HWE_IMSK, Y2_HWE_ALL_MASK);
+
+ spin_lock_bh(&hw->phy_lock);
+ for (i = 0; i < hw->ports; i++)
+ sky2_phy_reset(hw, i);
+ spin_unlock_bh(&hw->phy_lock);
+
+ memset(hw->st_le, 0, STATUS_LE_BYTES);
+ hw->st_idx = 0;
+
+ sky2_write32(hw, STAT_CTRL, SC_STAT_RST_SET);
+ sky2_write32(hw, STAT_CTRL, SC_STAT_RST_CLR);
+
+ sky2_write32(hw, STAT_LIST_ADDR_LO, hw->st_dma);
+ sky2_write32(hw, STAT_LIST_ADDR_HI, (u64) hw->st_dma >> 32);
+
+ /* Set the list last index */
+ sky2_write16(hw, STAT_LAST_IDX, STATUS_RING_SIZE - 1);
+
+ sky2_write32(hw, STAT_TX_TIMER_INI, sky2_ms2clk(hw, 10));
+
+ /* These status setup values are copied from SysKonnect's driver */
+ if (is_ec_a1(hw)) {
+ /* WA for dev. #4.3 */
+ sky2_write16(hw, STAT_TX_IDX_TH, 0xfff); /* Tx Threshold */
+
+ /* set Status-FIFO watermark */
+ sky2_write8(hw, STAT_FIFO_WM, 0x21); /* WA for dev. #4.18 */
+
+ /* set Status-FIFO ISR watermark */
+ sky2_write8(hw, STAT_FIFO_ISR_WM, 0x07); /* WA for dev. #4.18 */
+
+ } else {
+ sky2_write16(hw, STAT_TX_IDX_TH, 0x000a);
+
+ /* set Status-FIFO watermark */
+ sky2_write8(hw, STAT_FIFO_WM, 0x10);
+
+ /* set Status-FIFO ISR watermark */
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0)
+ sky2_write8(hw, STAT_FIFO_ISR_WM, 0x10);
+
+ else /* WA dev 4.109 */
+ sky2_write8(hw, STAT_FIFO_ISR_WM, 0x04);
+
+ sky2_write32(hw, STAT_ISR_TIMER_INI, 0x0190);
+ }
+
+ /* enable status unit */
+ sky2_write32(hw, STAT_CTRL, SC_STAT_OP_ON);
+
+ sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
+ sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
+ sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
+
+ return 0;
+}
+
+static inline u32 sky2_supported_modes(const struct sky2_hw *hw)
+{
+ u32 modes;
+ if (hw->copper) {
+ modes = SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_Autoneg | SUPPORTED_TP;
+
+ if (hw->chip_id != CHIP_ID_YUKON_FE)
+ modes |= SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full;
+ } else
+ modes = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
+ | SUPPORTED_Autoneg;
+ return modes;
+}
+
+static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+
+ ecmd->transceiver = XCVR_INTERNAL;
+ ecmd->supported = sky2_supported_modes(hw);
+ ecmd->phy_address = PHY_ADDR_MARV;
+ if (hw->copper) {
+ ecmd->supported = SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full
+ | SUPPORTED_Autoneg | SUPPORTED_TP;
+ ecmd->port = PORT_TP;
+ } else
+ ecmd->port = PORT_FIBRE;
+
+ ecmd->advertising = sky2->advertising;
+ ecmd->autoneg = sky2->autoneg;
+ ecmd->speed = sky2->speed;
+ ecmd->duplex = sky2->duplex;
+ return 0;
+}
+
+static int sky2_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ const struct sky2_hw *hw = sky2->hw;
+ u32 supported = sky2_supported_modes(hw);
+
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ ecmd->advertising = supported;
+ sky2->duplex = -1;
+ sky2->speed = -1;
+ } else {
+ u32 setting;
+
+ switch (ecmd->speed) {
+ case SPEED_1000:
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_1000baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_1000baseT_Half;
+ else
+ return -EINVAL;
+ break;
+ case SPEED_100:
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_100baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_100baseT_Half;
+ else
+ return -EINVAL;
+ break;
+
+ case SPEED_10:
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_10baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_10baseT_Half;
+ else
+ return -EINVAL;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if ((setting & supported) == 0)
+ return -EINVAL;
+
+ sky2->speed = ecmd->speed;
+ sky2->duplex = ecmd->duplex;
+ }
+
+ sky2->autoneg = ecmd->autoneg;
+ sky2->advertising = ecmd->advertising;
+
+ if (netif_running(dev)) {
+ sky2_down(dev);
+ sky2_up(dev);
+ }
+
+ return 0;
+}
+
+static void sky2_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ strcpy(info->driver, DRV_NAME);
+ strcpy(info->version, DRV_VERSION);
+ strcpy(info->fw_version, "N/A");
+ strcpy(info->bus_info, pci_name(sky2->hw->pdev));
+}
+
+static const struct sky2_stat {
+ char name[ETH_GSTRING_LEN];
+ u16 offset;
+} sky2_stats[] = {
+ { "tx_bytes", GM_TXO_OK_HI },
+ { "rx_bytes", GM_RXO_OK_HI },
+ { "tx_broadcast", GM_TXF_BC_OK },
+ { "rx_broadcast", GM_RXF_BC_OK },
+ { "tx_multicast", GM_TXF_MC_OK },
+ { "rx_multicast", GM_RXF_MC_OK },
+ { "tx_unicast", GM_TXF_UC_OK },
+ { "rx_unicast", GM_RXF_UC_OK },
+ { "tx_mac_pause", GM_TXF_MPAUSE },
+ { "rx_mac_pause", GM_RXF_MPAUSE },
+ { "collisions", GM_TXF_SNG_COL },
+ { "late_collision",GM_TXF_LAT_COL },
+ { "aborted", GM_TXF_ABO_COL },
+ { "multi_collisions", GM_TXF_MUL_COL },
+ { "fifo_underrun", GM_TXE_FIFO_UR },
+ { "fifo_overflow", GM_RXE_FIFO_OV },
+ { "rx_toolong", GM_RXF_LNG_ERR },
+ { "rx_jabber", GM_RXF_JAB_PKT },
+ { "rx_runt", GM_RXE_FRAG },
+ { "rx_too_long", GM_RXF_LNG_ERR },
+ { "rx_fcs_error", GM_RXF_FCS_ERR },
+};
+
+static u32 sky2_get_rx_csum(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ return sky2->rx_csum;
+}
+
+static int sky2_set_rx_csum(struct net_device *dev, u32 data)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ sky2->rx_csum = data;
+
+ sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR),
+ data ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
+
+ return 0;
+}
+
+static u32 sky2_get_msglevel(struct net_device *netdev)
+{
+ struct sky2_port *sky2 = netdev_priv(netdev);
+ return sky2->msg_enable;
+}
+
+static int sky2_nway_reset(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+
+ if (sky2->autoneg != AUTONEG_ENABLE)
+ return -EINVAL;
+
+ netif_stop_queue(dev);
+
+ spin_lock_irq(&hw->phy_lock);
+ sky2_phy_reset(hw, sky2->port);
+ sky2_phy_init(hw, sky2->port);
+ spin_unlock_irq(&hw->phy_lock);
+
+ return 0;
+}
+
+static void sky2_phy_stats(struct sky2_port *sky2, u64 * data, unsigned count)
+{
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ int i;
+
+ data[0] = (u64) gma_read32(hw, port, GM_TXO_OK_HI) << 32
+ | (u64) gma_read32(hw, port, GM_TXO_OK_LO);
+ data[1] = (u64) gma_read32(hw, port, GM_RXO_OK_HI) << 32
+ | (u64) gma_read32(hw, port, GM_RXO_OK_LO);
+
+ for (i = 2; i < count; i++)
+ data[i] = (u64) gma_read32(hw, port, sky2_stats[i].offset);
+}
+
+static void sky2_set_msglevel(struct net_device *netdev, u32 value)
+{
+ struct sky2_port *sky2 = netdev_priv(netdev);
+ sky2->msg_enable = value;
+}
+
+static int sky2_get_stats_count(struct net_device *dev)
+{
+ return ARRAY_SIZE(sky2_stats);
+}
+
+static void sky2_get_ethtool_stats(struct net_device *dev,
+ struct ethtool_stats *stats, u64 * data)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ sky2_phy_stats(sky2, data, ARRAY_SIZE(sky2_stats));
+}
+
+static void sky2_get_strings(struct net_device *dev, u32 stringset, u8 * data)
+{
+ int i;
+
+ switch (stringset) {
+ case ETH_SS_STATS:
+ for (i = 0; i < ARRAY_SIZE(sky2_stats); i++)
+ memcpy(data + i * ETH_GSTRING_LEN,
+ sky2_stats[i].name, ETH_GSTRING_LEN);
+ break;
+ }
+}
+
+/* Use hardware MIB variables for critical path statistics and
+ * transmit feedback not reported at interrupt.
+ * Other errors are accounted for in interrupt handler.
+ */
+static struct net_device_stats *sky2_get_stats(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ u64 data[13];
+
+ sky2_phy_stats(sky2, data, ARRAY_SIZE(data));
+
+ sky2->net_stats.tx_bytes = data[0];
+ sky2->net_stats.rx_bytes = data[1];
+ sky2->net_stats.tx_packets = data[2] + data[4] + data[6];
+ sky2->net_stats.rx_packets = data[3] + data[5] + data[7];
+ sky2->net_stats.multicast = data[5] + data[7];
+ sky2->net_stats.collisions = data[10];
+ sky2->net_stats.tx_aborted_errors = data[12];
+
+ return &sky2->net_stats;
+}
+
+static int sky2_set_mac_address(struct net_device *dev, void *p)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sockaddr *addr = p;
+ int err = 0;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ sky2_down(dev);
+ memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
+ memcpy_toio(sky2->hw->regs + B2_MAC_1 + sky2->port * 8,
+ dev->dev_addr, ETH_ALEN);
+ memcpy_toio(sky2->hw->regs + B2_MAC_2 + sky2->port * 8,
+ dev->dev_addr, ETH_ALEN);
+ if (dev->flags & IFF_UP)
+ err = sky2_up(dev);
+ return err;
+}
+
+static void sky2_set_multicast(struct net_device *dev)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ struct dev_mc_list *list = dev->mc_list;
+ u16 reg;
+ u8 filter[8];
+
+ memset(filter, 0, sizeof(filter));
+
+ reg = gma_read16(hw, port, GM_RX_CTRL);
+ reg |= GM_RXCR_UCF_ENA;
+
+ if (dev->flags & IFF_PROMISC) /* promiscuous */
+ reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
+ else if ((dev->flags & IFF_ALLMULTI) || dev->mc_count > 16) /* all multicast */
+ memset(filter, 0xff, sizeof(filter));
+ else if (dev->mc_count == 0) /* no multicast */
+ reg &= ~GM_RXCR_MCF_ENA;
+ else {
+ int i;
+ reg |= GM_RXCR_MCF_ENA;
+
+ for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
+ u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
+ filter[bit / 8] |= 1 << (bit % 8);
+ }
+ }
+
+ gma_write16(hw, port, GM_MC_ADDR_H1,
+ (u16) filter[0] | ((u16) filter[1] << 8));
+ gma_write16(hw, port, GM_MC_ADDR_H2,
+ (u16) filter[2] | ((u16) filter[3] << 8));
+ gma_write16(hw, port, GM_MC_ADDR_H3,
+ (u16) filter[4] | ((u16) filter[5] << 8));
+ gma_write16(hw, port, GM_MC_ADDR_H4,
+ (u16) filter[6] | ((u16) filter[7] << 8));
+
+ gma_write16(hw, port, GM_RX_CTRL, reg);
+}
+
+/* Can have one global because blinking is controlled by
+ * ethtool and that is always under RTNL mutex
+ */
+static inline void sky2_led(struct sky2_hw *hw, unsigned port, int on)
+{
+ u16 pg;
+
+ spin_lock_bh(&hw->phy_lock);
+ switch (hw->chip_id) {
+ case CHIP_ID_YUKON_XL:
+ pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
+ on ? (PHY_M_LEDC_LOS_CTRL(1) |
+ PHY_M_LEDC_INIT_CTRL(7) |
+ PHY_M_LEDC_STA1_CTRL(7) |
+ PHY_M_LEDC_STA0_CTRL(7))
+ : 0);
+
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
+ break;
+
+ default:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ on ? PHY_M_LED_MO_DUP(MO_LED_ON) |
+ PHY_M_LED_MO_10(MO_LED_ON) |
+ PHY_M_LED_MO_100(MO_LED_ON) |
+ PHY_M_LED_MO_1000(MO_LED_ON) |
+ PHY_M_LED_MO_RX(MO_LED_ON)
+ : PHY_M_LED_MO_DUP(MO_LED_OFF) |
+ PHY_M_LED_MO_10(MO_LED_OFF) |
+ PHY_M_LED_MO_100(MO_LED_OFF) |
+ PHY_M_LED_MO_1000(MO_LED_OFF) |
+ PHY_M_LED_MO_RX(MO_LED_OFF));
+
+ }
+ spin_unlock_bh(&hw->phy_lock);
+}
+
+/* blink LED's for finding board */
+static int sky2_phys_id(struct net_device *dev, u32 data)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ u16 ledctrl, ledover = 0;
+ long ms;
+ int onoff = 1;
+
+ if (!data || data > (u32) (MAX_SCHEDULE_TIMEOUT / HZ))
+ ms = jiffies_to_msecs(MAX_SCHEDULE_TIMEOUT);
+ else
+ ms = data * 1000;
+
+ /* save initial values */
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_YUKON_XL) {
+ u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
+ ledctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
+ } else {
+ ledctrl = gm_phy_read(hw, port, PHY_MARV_LED_CTRL);
+ ledover = gm_phy_read(hw, port, PHY_MARV_LED_OVER);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+
+ while (ms > 0) {
+ sky2_led(hw, port, onoff);
+ onoff = !onoff;
+
+ if (msleep_interruptible(250))
+ break; /* interrupted */
+ ms -= 250;
+ }
+
+ /* resume regularly scheduled programming */
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_YUKON_XL) {
+ u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ledctrl);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
+ } else {
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+
+ return 0;
+}
+
+static void sky2_get_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *ecmd)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ ecmd->tx_pause = sky2->tx_pause;
+ ecmd->rx_pause = sky2->rx_pause;
+ ecmd->autoneg = sky2->autoneg;
+}
+
+static int sky2_set_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *ecmd)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ int err = 0;
+
+ sky2->autoneg = ecmd->autoneg;
+ sky2->tx_pause = ecmd->tx_pause != 0;
+ sky2->rx_pause = ecmd->rx_pause != 0;
+
+ if (netif_running(dev)) {
+ sky2_down(dev);
+ err = sky2_up(dev);
+ }
+
+ return err;
+}
+
+#ifdef CONFIG_PM
+static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ wol->supported = WAKE_MAGIC;
+ wol->wolopts = sky2->wol ? WAKE_MAGIC : 0;
+}
+
+static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ struct sky2_hw *hw = sky2->hw;
+
+ if (wol->wolopts != WAKE_MAGIC && wol->wolopts != 0)
+ return -EOPNOTSUPP;
+
+ sky2->wol = wol->wolopts == WAKE_MAGIC;
+
+ if (sky2->wol) {
+ memcpy_toio(hw->regs + WOL_MAC_ADDR, dev->dev_addr, ETH_ALEN);
+
+ sky2_write16(hw, WOL_CTRL_STAT,
+ WOL_CTL_ENA_PME_ON_MAGIC_PKT |
+ WOL_CTL_ENA_MAGIC_PKT_UNIT);
+ } else
+ sky2_write16(hw, WOL_CTRL_STAT, WOL_CTL_DEFAULT);
+
+ return 0;
+}
+#endif
+
+static void sky2_get_ringparam(struct net_device *dev,
+ struct ethtool_ringparam *ering)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ ering->rx_max_pending = RX_MAX_PENDING;
+ ering->rx_mini_max_pending = 0;
+ ering->rx_jumbo_max_pending = 0;
+ ering->tx_max_pending = TX_RING_SIZE - 1;
+
+ ering->rx_pending = sky2->rx_pending;
+ ering->rx_mini_pending = 0;
+ ering->rx_jumbo_pending = 0;
+ ering->tx_pending = sky2->tx_pending;
+}
+
+static int sky2_set_ringparam(struct net_device *dev,
+ struct ethtool_ringparam *ering)
+{
+ struct sky2_port *sky2 = netdev_priv(dev);
+ int err = 0;
+
+ if (ering->rx_pending > RX_MAX_PENDING ||
+ ering->rx_pending < 8 ||
+ ering->tx_pending < MAX_SKB_TX_LE ||
+ ering->tx_pending > TX_RING_SIZE - 1)
+ return -EINVAL;
+
+ if (netif_running(dev))
+ sky2_down(dev);
+
+ sky2->rx_pending = ering->rx_pending;
+ sky2->tx_pending = ering->tx_pending;
+
+ if (netif_running(dev))
+ err = sky2_up(dev);
+
+ return err;
+}
+
+static int sky2_get_regs_len(struct net_device *dev)
+{
+ return 0x4000;
+}
+
+/*
+ * Returns copy of control register region
+ * Note: access to the RAM address register set will cause timeouts.
+ */
+static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs,
+ void *p)
+{
+ const struct sky2_port *sky2 = netdev_priv(dev);
+ const void __iomem *io = sky2->hw->regs;
+
+ BUG_ON(regs->len < B3_RI_WTO_R1);
+ regs->version = 1;
+ memset(p, 0, regs->len);
+
+ memcpy_fromio(p, io, B3_RAM_ADDR);
+
+ memcpy_fromio(p + B3_RI_WTO_R1,
+ io + B3_RI_WTO_R1,
+ regs->len - B3_RI_WTO_R1);
+}
+
+static struct ethtool_ops sky2_ethtool_ops = {
+ .get_settings = sky2_get_settings,
+ .set_settings = sky2_set_settings,
+ .get_drvinfo = sky2_get_drvinfo,
+ .get_msglevel = sky2_get_msglevel,
+ .set_msglevel = sky2_set_msglevel,
+ .nway_reset = sky2_nway_reset,
+ .get_regs_len = sky2_get_regs_len,
+ .get_regs = sky2_get_regs,
+ .get_link = ethtool_op_get_link,
+ .get_sg = ethtool_op_get_sg,
+ .set_sg = ethtool_op_set_sg,
+ .get_tx_csum = ethtool_op_get_tx_csum,
+ .set_tx_csum = ethtool_op_set_tx_csum,
+ .get_tso = ethtool_op_get_tso,
+ .set_tso = ethtool_op_set_tso,
+ .get_rx_csum = sky2_get_rx_csum,
+ .set_rx_csum = sky2_set_rx_csum,
+ .get_strings = sky2_get_strings,
+ .get_ringparam = sky2_get_ringparam,
+ .set_ringparam = sky2_set_ringparam,
+ .get_pauseparam = sky2_get_pauseparam,
+ .set_pauseparam = sky2_set_pauseparam,
+#ifdef CONFIG_PM
+ .get_wol = sky2_get_wol,
+ .set_wol = sky2_set_wol,
+#endif
+ .phys_id = sky2_phys_id,
+ .get_stats_count = sky2_get_stats_count,
+ .get_ethtool_stats = sky2_get_ethtool_stats,
+ .get_perm_addr = ethtool_op_get_perm_addr,
+};
+
+/* Initialize network device */
+static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
+ unsigned port, int highmem)
+{
+ struct sky2_port *sky2;
+ struct net_device *dev = alloc_etherdev(sizeof(*sky2));
+
+ if (!dev) {
+ printk(KERN_ERR "sky2 etherdev alloc failed");
+ return NULL;
+ }
+
+ SET_MODULE_OWNER(dev);
+ SET_NETDEV_DEV(dev, &hw->pdev->dev);
+ dev->open = sky2_up;
+ dev->stop = sky2_down;
+ dev->hard_start_xmit = sky2_xmit_frame;
+ dev->get_stats = sky2_get_stats;
+ dev->set_multicast_list = sky2_set_multicast;
+ dev->set_mac_address = sky2_set_mac_address;
+ dev->change_mtu = sky2_change_mtu;
+ SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops);
+ dev->tx_timeout = sky2_tx_timeout;
+ dev->watchdog_timeo = TX_WATCHDOG;
+ if (port == 0)
+ dev->poll = sky2_poll;
+ dev->weight = NAPI_WEIGHT;
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ dev->poll_controller = sky2_netpoll;
+#endif
+
+ sky2 = netdev_priv(dev);
+ sky2->netdev = dev;
+ sky2->hw = hw;
+ sky2->msg_enable = netif_msg_init(debug, default_msg);
+
+ spin_lock_init(&sky2->tx_lock);
+ /* Auto speed and flow control */
+ sky2->autoneg = AUTONEG_ENABLE;
+ sky2->tx_pause = 0;
+ sky2->rx_pause = 1;
+ sky2->duplex = -1;
+ sky2->speed = -1;
+ sky2->advertising = sky2_supported_modes(hw);
+ sky2->rx_csum = 1;
+ tasklet_init(&sky2->phy_task, sky2_phy_task, (unsigned long)sky2);
+ sky2->tx_pending = TX_DEF_PENDING;
+ sky2->rx_pending = is_ec_a1(hw) ? 8 : RX_DEF_PENDING;
+
+ hw->dev[port] = dev;
+
+ sky2->port = port;
+
+ dev->features |= NETIF_F_LLTX | NETIF_F_TSO;
+ if (highmem)
+ dev->features |= NETIF_F_HIGHDMA;
+ dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
+
+#ifdef SKY2_VLAN_TAG_USED
+ dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
+ dev->vlan_rx_register = sky2_vlan_rx_register;
+ dev->vlan_rx_kill_vid = sky2_vlan_rx_kill_vid;
+#endif
+
+ /* read the mac address */
+ memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, ETH_ALEN);
+ memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
+
+ /* device is off until link detection */
+ netif_carrier_off(dev);
+ netif_stop_queue(dev);
+
+ return dev;
+}
+
+static inline void sky2_show_addr(struct net_device *dev)
+{
+ const struct sky2_port *sky2 = netdev_priv(dev);
+
+ if (netif_msg_probe(sky2))
+ printk(KERN_INFO PFX "%s: addr %02x:%02x:%02x:%02x:%02x:%02x\n",
+ dev->name,
+ dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
+ dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
+}
+
+static int __devinit sky2_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct net_device *dev, *dev1 = NULL;
+ struct sky2_hw *hw;
+ int err, pm_cap, using_dac = 0;
+
+ err = pci_enable_device(pdev);
+ if (err) {
+ printk(KERN_ERR PFX "%s cannot enable PCI device\n",
+ pci_name(pdev));
+ goto err_out;
+ }
+
+ err = pci_request_regions(pdev, DRV_NAME);
+ if (err) {
+ printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
+ pci_name(pdev));
+ goto err_out;
+ }
+
+ pci_set_master(pdev);
+
+ /* Find power-management capability. */
+ pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM);
+ if (pm_cap == 0) {
+ printk(KERN_ERR PFX "Cannot find PowerManagement capability, "
+ "aborting.\n");
+ err = -EIO;
+ goto err_out_free_regions;
+ }
+
+ if (sizeof(dma_addr_t) > sizeof(u32)) {
+ err = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
+ if (!err)
+ using_dac = 1;
+ }
+
+ if (!using_dac) {
+ err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
+ if (err) {
+ printk(KERN_ERR PFX "%s no usable DMA configuration\n",
+ pci_name(pdev));
+ goto err_out_free_regions;
+ }
+ }
+#ifdef __BIG_ENDIAN
+ /* byte swap descriptors in hardware */
+ {
+ u32 reg;
+
+ pci_read_config_dword(pdev, PCI_DEV_REG2, &reg);
+ reg |= PCI_REV_DESC;
+ pci_write_config_dword(pdev, PCI_DEV_REG2, reg);
+ }
+#endif
+
+ err = -ENOMEM;
+ hw = kmalloc(sizeof(*hw), GFP_KERNEL);
+ if (!hw) {
+ printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
+ pci_name(pdev));
+ goto err_out_free_regions;
+ }
+
+ memset(hw, 0, sizeof(*hw));
+ hw->pdev = pdev;
+ spin_lock_init(&hw->phy_lock);
+
+ hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
+ if (!hw->regs) {
+ printk(KERN_ERR PFX "%s: cannot map device registers\n",
+ pci_name(pdev));
+ goto err_out_free_hw;
+ }
+ hw->pm_cap = pm_cap;
+
+ err = sky2_reset(hw);
+ if (err)
+ goto err_out_iounmap;
+
+ printk(KERN_INFO PFX "addr 0x%lx irq %d Yukon-%s (0x%x) rev %d\n",
+ pci_resource_start(pdev, 0), pdev->irq,
+ yukon_name[hw->chip_id - CHIP_ID_YUKON],
+ hw->chip_id, hw->chip_rev);
+
+ dev = sky2_init_netdev(hw, 0, using_dac);
+ if (!dev)
+ goto err_out_free_pci;
+
+ err = register_netdev(dev);
+ if (err) {
+ printk(KERN_ERR PFX "%s: cannot register net device\n",
+ pci_name(pdev));
+ goto err_out_free_netdev;
+ }
+
+ sky2_show_addr(dev);
+
+ if (hw->ports > 1 && (dev1 = sky2_init_netdev(hw, 1, using_dac))) {
+ if (register_netdev(dev1) == 0)
+ sky2_show_addr(dev1);
+ else {
+ /* Failure to register second port need not be fatal */
+ printk(KERN_WARNING PFX
+ "register of second port failed\n");
+ hw->dev[1] = NULL;
+ free_netdev(dev1);
+ }
+ }
+
+ err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ, DRV_NAME, hw);
+ if (err) {
+ printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
+ pci_name(pdev), pdev->irq);
+ goto err_out_unregister;
+ }
+
+ hw->intr_mask = Y2_IS_BASE;
+ sky2_write32(hw, B0_IMSK, hw->intr_mask);
+
+ pci_set_drvdata(pdev, hw);
+
+ return 0;
+
+err_out_unregister:
+ if (dev1) {
+ unregister_netdev(dev1);
+ free_netdev(dev1);
+ }
+ unregister_netdev(dev);
+err_out_free_netdev:
+ free_netdev(dev);
+err_out_free_pci:
+ sky2_write8(hw, B0_CTST, CS_RST_SET);
+ pci_free_consistent(hw->pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
+err_out_iounmap:
+ iounmap(hw->regs);
+err_out_free_hw:
+ kfree(hw);
+err_out_free_regions:
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+err_out:
+ return err;
+}
+
+static void __devexit sky2_remove(struct pci_dev *pdev)
+{
+ struct sky2_hw *hw = pci_get_drvdata(pdev);
+ struct net_device *dev0, *dev1;
+
+ if (!hw)
+ return;
+
+ dev0 = hw->dev[0];
+ dev1 = hw->dev[1];
+ if (dev1)
+ unregister_netdev(dev1);
+ unregister_netdev(dev0);
+
+ sky2_write32(hw, B0_IMSK, 0);
+ sky2_set_power_state(hw, PCI_D3hot);
+ sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
+ sky2_write8(hw, B0_CTST, CS_RST_SET);
+ sky2_read8(hw, B0_CTST);
+
+ free_irq(pdev->irq, hw);
+ pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+
+ if (dev1)
+ free_netdev(dev1);
+ free_netdev(dev0);
+ iounmap(hw->regs);
+ kfree(hw);
+
+ pci_set_drvdata(pdev, NULL);
+}
+
+#ifdef CONFIG_PM
+static int sky2_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ struct sky2_hw *hw = pci_get_drvdata(pdev);
+ int i;
+
+ for (i = 0; i < 2; i++) {
+ struct net_device *dev = hw->dev[i];
+
+ if (dev) {
+ if (!netif_running(dev))
+ continue;
+
+ sky2_down(dev);
+ netif_device_detach(dev);
+ }
+ }
+
+ return sky2_set_power_state(hw, pci_choose_state(pdev, state));
+}
+
+static int sky2_resume(struct pci_dev *pdev)
+{
+ struct sky2_hw *hw = pci_get_drvdata(pdev);
+ int i;
+
+ pci_restore_state(pdev);
+ pci_enable_wake(pdev, PCI_D0, 0);
+ sky2_set_power_state(hw, PCI_D0);
+
+ sky2_reset(hw);
+
+ for (i = 0; i < 2; i++) {
+ struct net_device *dev = hw->dev[i];
+ if (dev) {
+ if (netif_running(dev)) {
+ netif_device_attach(dev);
+ sky2_up(dev);
+ }
+ }
+ }
+ return 0;
+}
+#endif
+
+static struct pci_driver sky2_driver = {
+ .name = DRV_NAME,
+ .id_table = sky2_id_table,
+ .probe = sky2_probe,
+ .remove = __devexit_p(sky2_remove),
+#ifdef CONFIG_PM
+ .suspend = sky2_suspend,
+ .resume = sky2_resume,
+#endif
+};
+
+static int __init sky2_init_module(void)
+{
+ return pci_module_init(&sky2_driver);
+}
+
+static void __exit sky2_cleanup_module(void)
+{
+ pci_unregister_driver(&sky2_driver);
+}
+
+module_init(sky2_init_module);
+module_exit(sky2_cleanup_module);
+
+MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver");
+MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
new file mode 100644
index 00000000000..629d08f170f
--- /dev/null
+++ b/drivers/net/sky2.h
@@ -0,0 +1,1910 @@
+/*
+ * Definitions for the new Marvell Yukon 2 driver.
+ */
+#ifndef _SKY2_H
+#define _SKY2_H
+
+/* PCI config registers */
+#define PCI_DEV_REG1 0x40
+#define PCI_DEV_REG2 0x44
+#define PCI_DEV_STATUS 0x7c
+#define PCI_OS_PCI_X (1<<26)
+
+#define PEX_LNK_STAT 0xf2
+#define PEX_UNC_ERR_STAT 0x104
+#define PEX_DEV_CTRL 0xe8
+
+/* Yukon-2 */
+enum pci_dev_reg_1 {
+ PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */
+ PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */
+ PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */
+ PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */
+ PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
+ PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */
+};
+
+enum pci_dev_reg_2 {
+ PCI_VPD_WR_THR = 0xffL<<24, /* Bit 31..24: VPD Write Threshold */
+ PCI_DEV_SEL = 0x7fL<<17, /* Bit 23..17: EEPROM Device Select */
+ PCI_VPD_ROM_SZ = 7L<<14, /* Bit 16..14: VPD ROM Size */
+
+ PCI_PATCH_DIR = 0xfL<<8, /* Bit 11.. 8: Ext Patches dir 3..0 */
+ PCI_EXT_PATCHS = 0xfL<<4, /* Bit 7.. 4: Extended Patches 3..0 */
+ PCI_EN_DUMMY_RD = 1<<3, /* Enable Dummy Read */
+ PCI_REV_DESC = 1<<2, /* Reverse Desc. Bytes */
+
+ PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */
+};
+
+
+#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
+ PCI_STATUS_SIG_SYSTEM_ERROR | \
+ PCI_STATUS_REC_MASTER_ABORT | \
+ PCI_STATUS_REC_TARGET_ABORT | \
+ PCI_STATUS_PARITY)
+
+enum pex_dev_ctrl {
+ PEX_DC_MAX_RRS_MSK = 7<<12, /* Bit 14..12: Max. Read Request Size */
+ PEX_DC_EN_NO_SNOOP = 1<<11,/* Enable No Snoop */
+ PEX_DC_EN_AUX_POW = 1<<10,/* Enable AUX Power */
+ PEX_DC_EN_PHANTOM = 1<<9, /* Enable Phantom Functions */
+ PEX_DC_EN_EXT_TAG = 1<<8, /* Enable Extended Tag Field */
+ PEX_DC_MAX_PLS_MSK = 7<<5, /* Bit 7.. 5: Max. Payload Size Mask */
+ PEX_DC_EN_REL_ORD = 1<<4, /* Enable Relaxed Ordering */
+ PEX_DC_EN_UNS_RQ_RP = 1<<3, /* Enable Unsupported Request Reporting */
+ PEX_DC_EN_FAT_ER_RP = 1<<2, /* Enable Fatal Error Reporting */
+ PEX_DC_EN_NFA_ER_RP = 1<<1, /* Enable Non-Fatal Error Reporting */
+ PEX_DC_EN_COR_ER_RP = 1<<0, /* Enable Correctable Error Reporting */
+};
+#define PEX_DC_MAX_RD_RQ_SIZE(x) (((x)<<12) & PEX_DC_MAX_RRS_MSK)
+
+/* PEX_UNC_ERR_STAT PEX Uncorrectable Errors Status Register (Yukon-2) */
+enum pex_err {
+ PEX_UNSUP_REQ = 1<<20, /* Unsupported Request Error */
+
+ PEX_MALFOR_TLP = 1<<18, /* Malformed TLP */
+
+ PEX_UNEXP_COMP = 1<<16, /* Unexpected Completion */
+
+ PEX_COMP_TO = 1<<14, /* Completion Timeout */
+ PEX_FLOW_CTRL_P = 1<<13, /* Flow Control Protocol Error */
+ PEX_POIS_TLP = 1<<12, /* Poisoned TLP */
+
+ PEX_DATA_LINK_P = 1<<4, /* Data Link Protocol Error */
+ PEX_FATAL_ERRORS= (PEX_MALFOR_TLP | PEX_FLOW_CTRL_P | PEX_DATA_LINK_P),
+};
+
+
+enum csr_regs {
+ B0_RAP = 0x0000,
+ B0_CTST = 0x0004,
+ B0_Y2LED = 0x0005,
+ B0_POWER_CTRL = 0x0007,
+ B0_ISRC = 0x0008,
+ B0_IMSK = 0x000c,
+ B0_HWE_ISRC = 0x0010,
+ B0_HWE_IMSK = 0x0014,
+
+ /* Special ISR registers (Yukon-2 only) */
+ B0_Y2_SP_ISRC2 = 0x001c,
+ B0_Y2_SP_ISRC3 = 0x0020,
+ B0_Y2_SP_EISR = 0x0024,
+ B0_Y2_SP_LISR = 0x0028,
+ B0_Y2_SP_ICR = 0x002c,
+
+ B2_MAC_1 = 0x0100,
+ B2_MAC_2 = 0x0108,
+ B2_MAC_3 = 0x0110,
+ B2_CONN_TYP = 0x0118,
+ B2_PMD_TYP = 0x0119,
+ B2_MAC_CFG = 0x011a,
+ B2_CHIP_ID = 0x011b,
+ B2_E_0 = 0x011c,
+
+ B2_Y2_CLK_GATE = 0x011d,
+ B2_Y2_HW_RES = 0x011e,
+ B2_E_3 = 0x011f,
+ B2_Y2_CLK_CTRL = 0x0120,
+
+ B2_TI_INI = 0x0130,
+ B2_TI_VAL = 0x0134,
+ B2_TI_CTRL = 0x0138,
+ B2_TI_TEST = 0x0139,
+
+ B2_TST_CTRL1 = 0x0158,
+ B2_TST_CTRL2 = 0x0159,
+ B2_GP_IO = 0x015c,
+
+ B2_I2C_CTRL = 0x0160,
+ B2_I2C_DATA = 0x0164,
+ B2_I2C_IRQ = 0x0168,
+ B2_I2C_SW = 0x016c,
+
+ B3_RAM_ADDR = 0x0180,
+ B3_RAM_DATA_LO = 0x0184,
+ B3_RAM_DATA_HI = 0x0188,
+
+/* RAM Interface Registers */
+/* Yukon-2: use RAM_BUFFER() to access the RAM buffer */
+/*
+ * The HW-Spec. calls this registers Timeout Value 0..11. But this names are
+ * not usable in SW. Please notice these are NOT real timeouts, these are
+ * the number of qWords transferred continuously.
+ */
+#define RAM_BUFFER(port, reg) (reg | (port <<6))
+
+ B3_RI_WTO_R1 = 0x0190,
+ B3_RI_WTO_XA1 = 0x0191,
+ B3_RI_WTO_XS1 = 0x0192,
+ B3_RI_RTO_R1 = 0x0193,
+ B3_RI_RTO_XA1 = 0x0194,
+ B3_RI_RTO_XS1 = 0x0195,
+ B3_RI_WTO_R2 = 0x0196,
+ B3_RI_WTO_XA2 = 0x0197,
+ B3_RI_WTO_XS2 = 0x0198,
+ B3_RI_RTO_R2 = 0x0199,
+ B3_RI_RTO_XA2 = 0x019a,
+ B3_RI_RTO_XS2 = 0x019b,
+ B3_RI_TO_VAL = 0x019c,
+ B3_RI_CTRL = 0x01a0,
+ B3_RI_TEST = 0x01a2,
+ B3_MA_TOINI_RX1 = 0x01b0,
+ B3_MA_TOINI_RX2 = 0x01b1,
+ B3_MA_TOINI_TX1 = 0x01b2,
+ B3_MA_TOINI_TX2 = 0x01b3,
+ B3_MA_TOVAL_RX1 = 0x01b4,
+ B3_MA_TOVAL_RX2 = 0x01b5,
+ B3_MA_TOVAL_TX1 = 0x01b6,
+ B3_MA_TOVAL_TX2 = 0x01b7,
+ B3_MA_TO_CTRL = 0x01b8,
+ B3_MA_TO_TEST = 0x01ba,
+ B3_MA_RCINI_RX1 = 0x01c0,
+ B3_MA_RCINI_RX2 = 0x01c1,
+ B3_MA_RCINI_TX1 = 0x01c2,
+ B3_MA_RCINI_TX2 = 0x01c3,
+ B3_MA_RCVAL_RX1 = 0x01c4,
+ B3_MA_RCVAL_RX2 = 0x01c5,
+ B3_MA_RCVAL_TX1 = 0x01c6,
+ B3_MA_RCVAL_TX2 = 0x01c7,
+ B3_MA_RC_CTRL = 0x01c8,
+ B3_MA_RC_TEST = 0x01ca,
+ B3_PA_TOINI_RX1 = 0x01d0,
+ B3_PA_TOINI_RX2 = 0x01d4,
+ B3_PA_TOINI_TX1 = 0x01d8,
+ B3_PA_TOINI_TX2 = 0x01dc,
+ B3_PA_TOVAL_RX1 = 0x01e0,
+ B3_PA_TOVAL_RX2 = 0x01e4,
+ B3_PA_TOVAL_TX1 = 0x01e8,
+ B3_PA_TOVAL_TX2 = 0x01ec,
+ B3_PA_CTRL = 0x01f0,
+ B3_PA_TEST = 0x01f2,
+
+ Y2_CFG_SPC = 0x1c00,
+};
+
+/* B0_CTST 16 bit Control/Status register */
+enum {
+ Y2_VMAIN_AVAIL = 1<<17,/* VMAIN available (YUKON-2 only) */
+ Y2_VAUX_AVAIL = 1<<16,/* VAUX available (YUKON-2 only) */
+ Y2_ASF_ENABLE = 1<<13,/* ASF Unit Enable (YUKON-2 only) */
+ Y2_ASF_DISABLE = 1<<12,/* ASF Unit Disable (YUKON-2 only) */
+ Y2_CLK_RUN_ENA = 1<<11,/* CLK_RUN Enable (YUKON-2 only) */
+ Y2_CLK_RUN_DIS = 1<<10,/* CLK_RUN Disable (YUKON-2 only) */
+ Y2_LED_STAT_ON = 1<<9, /* Status LED On (YUKON-2 only) */
+ Y2_LED_STAT_OFF = 1<<8, /* Status LED Off (YUKON-2 only) */
+
+ CS_ST_SW_IRQ = 1<<7, /* Set IRQ SW Request */
+ CS_CL_SW_IRQ = 1<<6, /* Clear IRQ SW Request */
+ CS_STOP_DONE = 1<<5, /* Stop Master is finished */
+ CS_STOP_MAST = 1<<4, /* Command Bit to stop the master */
+ CS_MRST_CLR = 1<<3, /* Clear Master reset */
+ CS_MRST_SET = 1<<2, /* Set Master reset */
+ CS_RST_CLR = 1<<1, /* Clear Software reset */
+ CS_RST_SET = 1, /* Set Software reset */
+};
+
+/* B0_LED 8 Bit LED register */
+enum {
+/* Bit 7.. 2: reserved */
+ LED_STAT_ON = 1<<1, /* Status LED on */
+ LED_STAT_OFF = 1, /* Status LED off */
+};
+
+/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
+enum {
+ PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */
+ PC_VAUX_DIS = 1<<6, /* Switch VAUX Disable */
+ PC_VCC_ENA = 1<<5, /* Switch VCC Enable */
+ PC_VCC_DIS = 1<<4, /* Switch VCC Disable */
+ PC_VAUX_ON = 1<<3, /* Switch VAUX On */
+ PC_VAUX_OFF = 1<<2, /* Switch VAUX Off */
+ PC_VCC_ON = 1<<1, /* Switch VCC On */
+ PC_VCC_OFF = 1<<0, /* Switch VCC Off */
+};
+
+/* B2_IRQM_MSK 32 bit IRQ Moderation Mask */
+
+/* B0_Y2_SP_ISRC2 32 bit Special Interrupt Source Reg 2 */
+/* B0_Y2_SP_ISRC3 32 bit Special Interrupt Source Reg 3 */
+/* B0_Y2_SP_EISR 32 bit Enter ISR Reg */
+/* B0_Y2_SP_LISR 32 bit Leave ISR Reg */
+enum {
+ Y2_IS_HW_ERR = 1<<31, /* Interrupt HW Error */
+ Y2_IS_STAT_BMU = 1<<30, /* Status BMU Interrupt */
+ Y2_IS_ASF = 1<<29, /* ASF subsystem Interrupt */
+
+ Y2_IS_POLL_CHK = 1<<27, /* Check IRQ from polling unit */
+ Y2_IS_TWSI_RDY = 1<<26, /* IRQ on end of TWSI Tx */
+ Y2_IS_IRQ_SW = 1<<25, /* SW forced IRQ */
+ Y2_IS_TIMINT = 1<<24, /* IRQ from Timer */
+
+ Y2_IS_IRQ_PHY2 = 1<<12, /* Interrupt from PHY 2 */
+ Y2_IS_IRQ_MAC2 = 1<<11, /* Interrupt from MAC 2 */
+ Y2_IS_CHK_RX2 = 1<<10, /* Descriptor error Rx 2 */
+ Y2_IS_CHK_TXS2 = 1<<9, /* Descriptor error TXS 2 */
+ Y2_IS_CHK_TXA2 = 1<<8, /* Descriptor error TXA 2 */
+
+ Y2_IS_IRQ_PHY1 = 1<<4, /* Interrupt from PHY 1 */
+ Y2_IS_IRQ_MAC1 = 1<<3, /* Interrupt from MAC 1 */
+ Y2_IS_CHK_RX1 = 1<<2, /* Descriptor error Rx 1 */
+ Y2_IS_CHK_TXS1 = 1<<1, /* Descriptor error TXS 1 */
+ Y2_IS_CHK_TXA1 = 1<<0, /* Descriptor error TXA 1 */
+
+ Y2_IS_BASE = Y2_IS_HW_ERR | Y2_IS_STAT_BMU |
+ Y2_IS_POLL_CHK | Y2_IS_TWSI_RDY |
+ Y2_IS_IRQ_SW | Y2_IS_TIMINT,
+ Y2_IS_PORT_1 = Y2_IS_IRQ_PHY1 | Y2_IS_IRQ_MAC1 |
+ Y2_IS_CHK_RX1 | Y2_IS_CHK_TXA1 | Y2_IS_CHK_TXS1,
+ Y2_IS_PORT_2 = Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2 |
+ Y2_IS_CHK_RX2 | Y2_IS_CHK_TXA2 | Y2_IS_CHK_TXS2,
+};
+
+/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
+enum {
+ IS_ERR_MSK = 0x00003fff,/* All Error bits */
+
+ IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
+ IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */
+ IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */
+ IS_IRQ_STAT = 1<<10, /* IRQ status exception */
+ IS_NO_STAT_M1 = 1<<9, /* No Rx Status from MAC 1 */
+ IS_NO_STAT_M2 = 1<<8, /* No Rx Status from MAC 2 */
+ IS_NO_TIST_M1 = 1<<7, /* No Time Stamp from MAC 1 */
+ IS_NO_TIST_M2 = 1<<6, /* No Time Stamp from MAC 2 */
+ IS_RAM_RD_PAR = 1<<5, /* RAM Read Parity Error */
+ IS_RAM_WR_PAR = 1<<4, /* RAM Write Parity Error */
+ IS_M1_PAR_ERR = 1<<3, /* MAC 1 Parity Error */
+ IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */
+ IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */
+ IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */
+};
+
+/* Hardware error interrupt mask for Yukon 2 */
+enum {
+ Y2_IS_TIST_OV = 1<<29,/* Time Stamp Timer overflow interrupt */
+ Y2_IS_SENSOR = 1<<28, /* Sensor interrupt */
+ Y2_IS_MST_ERR = 1<<27, /* Master error interrupt */
+ Y2_IS_IRQ_STAT = 1<<26, /* Status exception interrupt */
+ Y2_IS_PCI_EXP = 1<<25, /* PCI-Express interrupt */
+ Y2_IS_PCI_NEXP = 1<<24, /* PCI-Express error similar to PCI error */
+ /* Link 2 */
+ Y2_IS_PAR_RD2 = 1<<13, /* Read RAM parity error interrupt */
+ Y2_IS_PAR_WR2 = 1<<12, /* Write RAM parity error interrupt */
+ Y2_IS_PAR_MAC2 = 1<<11, /* MAC hardware fault interrupt */
+ Y2_IS_PAR_RX2 = 1<<10, /* Parity Error Rx Queue 2 */
+ Y2_IS_TCP_TXS2 = 1<<9, /* TCP length mismatch sync Tx queue IRQ */
+ Y2_IS_TCP_TXA2 = 1<<8, /* TCP length mismatch async Tx queue IRQ */
+ /* Link 1 */
+ Y2_IS_PAR_RD1 = 1<<5, /* Read RAM parity error interrupt */
+ Y2_IS_PAR_WR1 = 1<<4, /* Write RAM parity error interrupt */
+ Y2_IS_PAR_MAC1 = 1<<3, /* MAC hardware fault interrupt */
+ Y2_IS_PAR_RX1 = 1<<2, /* Parity Error Rx Queue 1 */
+ Y2_IS_TCP_TXS1 = 1<<1, /* TCP length mismatch sync Tx queue IRQ */
+ Y2_IS_TCP_TXA1 = 1<<0, /* TCP length mismatch async Tx queue IRQ */
+
+ Y2_HWE_L1_MASK = Y2_IS_PAR_RD1 | Y2_IS_PAR_WR1 | Y2_IS_PAR_MAC1 |
+ Y2_IS_PAR_RX1 | Y2_IS_TCP_TXS1| Y2_IS_TCP_TXA1,
+ Y2_HWE_L2_MASK = Y2_IS_PAR_RD2 | Y2_IS_PAR_WR2 | Y2_IS_PAR_MAC2 |
+ Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2,
+
+ Y2_HWE_ALL_MASK = Y2_IS_TIST_OV | Y2_IS_MST_ERR | Y2_IS_IRQ_STAT |
+ Y2_IS_PCI_EXP | Y2_IS_PCI_NEXP |
+ Y2_HWE_L1_MASK | Y2_HWE_L2_MASK,
+};
+
+/* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */
+enum {
+ DPT_START = 1<<1,
+ DPT_STOP = 1<<0,
+};
+
+/* B2_TST_CTRL1 8 bit Test Control Register 1 */
+enum {
+ TST_FRC_DPERR_MR = 1<<7, /* force DATAPERR on MST RD */
+ TST_FRC_DPERR_MW = 1<<6, /* force DATAPERR on MST WR */
+ TST_FRC_DPERR_TR = 1<<5, /* force DATAPERR on TRG RD */
+ TST_FRC_DPERR_TW = 1<<4, /* force DATAPERR on TRG WR */
+ TST_FRC_APERR_M = 1<<3, /* force ADDRPERR on MST */
+ TST_FRC_APERR_T = 1<<2, /* force ADDRPERR on TRG */
+ TST_CFG_WRITE_ON = 1<<1, /* Enable Config Reg WR */
+ TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */
+};
+
+/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */
+enum {
+ CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */
+ /* Bit 3.. 2: reserved */
+ CFG_DIS_M2_CLK = 1<<1, /* Disable Clock for 2nd MAC */
+ CFG_SNG_MAC = 1<<0, /* MAC Config: 0=2 MACs / 1=1 MAC*/
+};
+
+/* B2_CHIP_ID 8 bit Chip Identification Number */
+enum {
+ CHIP_ID_GENESIS = 0x0a, /* Chip ID for GENESIS */
+ CHIP_ID_YUKON = 0xb0, /* Chip ID for YUKON */
+ CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
+ CHIP_ID_YUKON_LP = 0xb2, /* Chip ID for YUKON-LP */
+ CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */
+ CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */
+ CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */
+
+ CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */
+ CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */
+ CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */
+};
+
+/* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */
+enum {
+ Y2_STATUS_LNK2_INAC = 1<<7, /* Status Link 2 inactive (0 = active) */
+ Y2_CLK_GAT_LNK2_DIS = 1<<6, /* Disable clock gating Link 2 */
+ Y2_COR_CLK_LNK2_DIS = 1<<5, /* Disable Core clock Link 2 */
+ Y2_PCI_CLK_LNK2_DIS = 1<<4, /* Disable PCI clock Link 2 */
+ Y2_STATUS_LNK1_INAC = 1<<3, /* Status Link 1 inactive (0 = active) */
+ Y2_CLK_GAT_LNK1_DIS = 1<<2, /* Disable clock gating Link 1 */
+ Y2_COR_CLK_LNK1_DIS = 1<<1, /* Disable Core clock Link 1 */
+ Y2_PCI_CLK_LNK1_DIS = 1<<0, /* Disable PCI clock Link 1 */
+};
+
+/* B2_Y2_HW_RES 8 bit HW Resources (Yukon-2 only) */
+enum {
+ CFG_LED_MODE_MSK = 7<<2, /* Bit 4.. 2: LED Mode Mask */
+ CFG_LINK_2_AVAIL = 1<<1, /* Link 2 available */
+ CFG_LINK_1_AVAIL = 1<<0, /* Link 1 available */
+};
+#define CFG_LED_MODE(x) (((x) & CFG_LED_MODE_MSK) >> 2)
+#define CFG_DUAL_MAC_MSK (CFG_LINK_2_AVAIL | CFG_LINK_1_AVAIL)
+
+
+/* B2_Y2_CLK_CTRL 32 bit Clock Frequency Control Register (Yukon-2/EC) */
+enum {
+ Y2_CLK_DIV_VAL_MSK = 0xff<<16,/* Bit 23..16: Clock Divisor Value */
+#define Y2_CLK_DIV_VAL(x) (((x)<<16) & Y2_CLK_DIV_VAL_MSK)
+ Y2_CLK_DIV_VAL2_MSK = 7<<21, /* Bit 23..21: Clock Divisor Value */
+ Y2_CLK_SELECT2_MSK = 0x1f<<16,/* Bit 20..16: Clock Select */
+#define Y2_CLK_DIV_VAL_2(x) (((x)<<21) & Y2_CLK_DIV_VAL2_MSK)
+#define Y2_CLK_SEL_VAL_2(x) (((x)<<16) & Y2_CLK_SELECT2_MSK)
+ Y2_CLK_DIV_ENA = 1<<1, /* Enable Core Clock Division */
+ Y2_CLK_DIV_DIS = 1<<0, /* Disable Core Clock Division */
+};
+
+/* B2_TI_CTRL 8 bit Timer control */
+/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */
+enum {
+ TIM_START = 1<<2, /* Start Timer */
+ TIM_STOP = 1<<1, /* Stop Timer */
+ TIM_CLR_IRQ = 1<<0, /* Clear Timer IRQ (!IRQM) */
+};
+
+/* B2_TI_TEST 8 Bit Timer Test */
+/* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */
+/* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */
+enum {
+ TIM_T_ON = 1<<2, /* Test mode on */
+ TIM_T_OFF = 1<<1, /* Test mode off */
+ TIM_T_STEP = 1<<0, /* Test step */
+};
+
+/* B3_RAM_ADDR 32 bit RAM Address, to read or write */
+ /* Bit 31..19: reserved */
+#define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */
+/* RAM Interface Registers */
+
+/* B3_RI_CTRL 16 bit RAM Interface Control Register */
+enum {
+ RI_CLR_RD_PERR = 1<<9, /* Clear IRQ RAM Read Parity Err */
+ RI_CLR_WR_PERR = 1<<8, /* Clear IRQ RAM Write Parity Err*/
+
+ RI_RST_CLR = 1<<1, /* Clear RAM Interface Reset */
+ RI_RST_SET = 1<<0, /* Set RAM Interface Reset */
+};
+
+#define SK_RI_TO_53 36 /* RAM interface timeout */
+
+
+/* Port related registers FIFO, and Arbiter */
+#define SK_REG(port,reg) (((port)<<7)+(reg))
+
+/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
+/* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */
+/* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */
+/* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */
+/* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */
+
+#define TXA_MAX_VAL 0x00ffffffUL /* Bit 23.. 0: Max TXA Timer/Cnt Val */
+
+/* TXA_CTRL 8 bit Tx Arbiter Control Register */
+enum {
+ TXA_ENA_FSYNC = 1<<7, /* Enable force of sync Tx queue */
+ TXA_DIS_FSYNC = 1<<6, /* Disable force of sync Tx queue */
+ TXA_ENA_ALLOC = 1<<5, /* Enable alloc of free bandwidth */
+ TXA_DIS_ALLOC = 1<<4, /* Disable alloc of free bandwidth */
+ TXA_START_RC = 1<<3, /* Start sync Rate Control */
+ TXA_STOP_RC = 1<<2, /* Stop sync Rate Control */
+ TXA_ENA_ARB = 1<<1, /* Enable Tx Arbiter */
+ TXA_DIS_ARB = 1<<0, /* Disable Tx Arbiter */
+};
+
+/*
+ * Bank 4 - 5
+ */
+/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
+enum {
+ TXA_ITI_INI = 0x0200,/* 32 bit Tx Arb Interval Timer Init Val*/
+ TXA_ITI_VAL = 0x0204,/* 32 bit Tx Arb Interval Timer Value */
+ TXA_LIM_INI = 0x0208,/* 32 bit Tx Arb Limit Counter Init Val */
+ TXA_LIM_VAL = 0x020c,/* 32 bit Tx Arb Limit Counter Value */
+ TXA_CTRL = 0x0210,/* 8 bit Tx Arbiter Control Register */
+ TXA_TEST = 0x0211,/* 8 bit Tx Arbiter Test Register */
+ TXA_STAT = 0x0212,/* 8 bit Tx Arbiter Status Register */
+};
+
+
+enum {
+ B6_EXT_REG = 0x0300,/* External registers (GENESIS only) */
+ B7_CFG_SPC = 0x0380,/* copy of the Configuration register */
+ B8_RQ1_REGS = 0x0400,/* Receive Queue 1 */
+ B8_RQ2_REGS = 0x0480,/* Receive Queue 2 */
+ B8_TS1_REGS = 0x0600,/* Transmit sync queue 1 */
+ B8_TA1_REGS = 0x0680,/* Transmit async queue 1 */
+ B8_TS2_REGS = 0x0700,/* Transmit sync queue 2 */
+ B8_TA2_REGS = 0x0780,/* Transmit sync queue 2 */
+ B16_RAM_REGS = 0x0800,/* RAM Buffer Registers */
+};
+
+/* Queue Register Offsets, use Q_ADDR() to access */
+enum {
+ B8_Q_REGS = 0x0400, /* base of Queue registers */
+ Q_D = 0x00, /* 8*32 bit Current Descriptor */
+ Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */
+ Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */
+ Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */
+ Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */
+ Q_BC = 0x30, /* 32 bit Current Byte Counter */
+ Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */
+ Q_F = 0x38, /* 32 bit Flag Register */
+ Q_T1 = 0x3c, /* 32 bit Test Register 1 */
+ Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */
+ Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */
+ Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */
+ Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */
+ Q_T2 = 0x40, /* 32 bit Test Register 2 */
+ Q_T3 = 0x44, /* 32 bit Test Register 3 */
+
+/* Yukon-2 */
+ Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */
+ Q_WM = 0x40, /* 16 bit FIFO Watermark */
+ Q_AL = 0x42, /* 8 bit FIFO Alignment */
+ Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */
+ Q_RSL = 0x46, /* 8 bit FIFO Read Shadow Level */
+ Q_RP = 0x48, /* 8 bit FIFO Read Pointer */
+ Q_RL = 0x4a, /* 8 bit FIFO Read Level */
+ Q_WP = 0x4c, /* 8 bit FIFO Write Pointer */
+ Q_WSP = 0x4d, /* 8 bit FIFO Write Shadow Pointer */
+ Q_WL = 0x4e, /* 8 bit FIFO Write Level */
+ Q_WSL = 0x4f, /* 8 bit FIFO Write Shadow Level */
+};
+#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
+
+
+/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
+enum {
+ Y2_B8_PREF_REGS = 0x0450,
+
+ PREF_UNIT_CTRL = 0x00, /* 32 bit Control register */
+ PREF_UNIT_LAST_IDX = 0x04, /* 16 bit Last Index */
+ PREF_UNIT_ADDR_LO = 0x08, /* 32 bit List start addr, low part */
+ PREF_UNIT_ADDR_HI = 0x0c, /* 32 bit List start addr, high part*/
+ PREF_UNIT_GET_IDX = 0x10, /* 16 bit Get Index */
+ PREF_UNIT_PUT_IDX = 0x14, /* 16 bit Put Index */
+ PREF_UNIT_FIFO_WP = 0x20, /* 8 bit FIFO write pointer */
+ PREF_UNIT_FIFO_RP = 0x24, /* 8 bit FIFO read pointer */
+ PREF_UNIT_FIFO_WM = 0x28, /* 8 bit FIFO watermark */
+ PREF_UNIT_FIFO_LEV = 0x2c, /* 8 bit FIFO level */
+
+ PREF_UNIT_MASK_IDX = 0x0fff,
+};
+#define Y2_QADDR(q,reg) (Y2_B8_PREF_REGS + (q) + (reg))
+
+/* RAM Buffer Register Offsets */
+enum {
+
+ RB_START = 0x00,/* 32 bit RAM Buffer Start Address */
+ RB_END = 0x04,/* 32 bit RAM Buffer End Address */
+ RB_WP = 0x08,/* 32 bit RAM Buffer Write Pointer */
+ RB_RP = 0x0c,/* 32 bit RAM Buffer Read Pointer */
+ RB_RX_UTPP = 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */
+ RB_RX_LTPP = 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */
+ RB_RX_UTHP = 0x18,/* 32 bit Rx Upper Threshold, High Prio */
+ RB_RX_LTHP = 0x1c,/* 32 bit Rx Lower Threshold, High Prio */
+ /* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */
+ RB_PC = 0x20,/* 32 bit RAM Buffer Packet Counter */
+ RB_LEV = 0x24,/* 32 bit RAM Buffer Level Register */
+ RB_CTRL = 0x28,/* 32 bit RAM Buffer Control Register */
+ RB_TST1 = 0x29,/* 8 bit RAM Buffer Test Register 1 */
+ RB_TST2 = 0x2a,/* 8 bit RAM Buffer Test Register 2 */
+};
+
+/* Receive and Transmit Queues */
+enum {
+ Q_R1 = 0x0000, /* Receive Queue 1 */
+ Q_R2 = 0x0080, /* Receive Queue 2 */
+ Q_XS1 = 0x0200, /* Synchronous Transmit Queue 1 */
+ Q_XA1 = 0x0280, /* Asynchronous Transmit Queue 1 */
+ Q_XS2 = 0x0300, /* Synchronous Transmit Queue 2 */
+ Q_XA2 = 0x0380, /* Asynchronous Transmit Queue 2 */
+};
+
+/* Different PHY Types */
+enum {
+ PHY_ADDR_MARV = 0,
+};
+
+#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
+
+
+enum {
+ LNK_SYNC_INI = 0x0c30,/* 32 bit Link Sync Cnt Init Value */
+ LNK_SYNC_VAL = 0x0c34,/* 32 bit Link Sync Cnt Current Value */
+ LNK_SYNC_CTRL = 0x0c38,/* 8 bit Link Sync Cnt Control Register */
+ LNK_SYNC_TST = 0x0c39,/* 8 bit Link Sync Cnt Test Register */
+
+ LNK_LED_REG = 0x0c3c,/* 8 bit Link LED Register */
+
+/* Receive GMAC FIFO (YUKON and Yukon-2) */
+
+ RX_GMF_EA = 0x0c40,/* 32 bit Rx GMAC FIFO End Address */
+ RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */
+ RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */
+ RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */
+ RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */
+ RX_GMF_TR_THR = 0x0c54,/* 32 bit Rx Truncation Threshold (Yukon-2) */
+
+ RX_GMF_VLAN = 0x0c5c,/* 32 bit Rx VLAN Type Register (Yukon-2) */
+ RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */
+
+ RX_GMF_WLEV = 0x0c68,/* 32 bit Rx GMAC FIFO Write Level */
+
+ RX_GMF_RP = 0x0c70,/* 32 bit Rx GMAC FIFO Read Pointer */
+
+ RX_GMF_RLEV = 0x0c78,/* 32 bit Rx GMAC FIFO Read Level */
+};
+
+
+/* Q_BC 32 bit Current Byte Counter */
+
+/* BMU Control Status Registers */
+/* B0_R1_CSR 32 bit BMU Ctrl/Stat Rx Queue 1 */
+/* B0_R2_CSR 32 bit BMU Ctrl/Stat Rx Queue 2 */
+/* B0_XA1_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */
+/* B0_XS1_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 1 */
+/* B0_XA2_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */
+/* B0_XS2_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 2 */
+/* Q_CSR 32 bit BMU Control/Status Register */
+
+/* Rx BMU Control / Status Registers (Yukon-2) */
+enum {
+ BMU_IDLE = 1<<31, /* BMU Idle State */
+ BMU_RX_TCP_PKT = 1<<30, /* Rx TCP Packet (when RSS Hash enabled) */
+ BMU_RX_IP_PKT = 1<<29, /* Rx IP Packet (when RSS Hash enabled) */
+
+ BMU_ENA_RX_RSS_HASH = 1<<15, /* Enable Rx RSS Hash */
+ BMU_DIS_RX_RSS_HASH = 1<<14, /* Disable Rx RSS Hash */
+ BMU_ENA_RX_CHKSUM = 1<<13, /* Enable Rx TCP/IP Checksum Check */
+ BMU_DIS_RX_CHKSUM = 1<<12, /* Disable Rx TCP/IP Checksum Check */
+ BMU_CLR_IRQ_PAR = 1<<11, /* Clear IRQ on Parity errors (Rx) */
+ BMU_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segment. error (Tx) */
+ BMU_CLR_IRQ_CHK = 1<<10, /* Clear IRQ Check */
+ BMU_STOP = 1<<9, /* Stop Rx/Tx Queue */
+ BMU_START = 1<<8, /* Start Rx/Tx Queue */
+ BMU_FIFO_OP_ON = 1<<7, /* FIFO Operational On */
+ BMU_FIFO_OP_OFF = 1<<6, /* FIFO Operational Off */
+ BMU_FIFO_ENA = 1<<5, /* Enable FIFO */
+ BMU_FIFO_RST = 1<<4, /* Reset FIFO */
+ BMU_OP_ON = 1<<3, /* BMU Operational On */
+ BMU_OP_OFF = 1<<2, /* BMU Operational Off */
+ BMU_RST_CLR = 1<<1, /* Clear BMU Reset (Enable) */
+ BMU_RST_SET = 1<<0, /* Set BMU Reset */
+
+ BMU_CLR_RESET = BMU_FIFO_RST | BMU_OP_OFF | BMU_RST_CLR,
+ BMU_OPER_INIT = BMU_CLR_IRQ_PAR | BMU_CLR_IRQ_CHK | BMU_START |
+ BMU_FIFO_ENA | BMU_OP_ON,
+};
+
+/* Tx BMU Control / Status Registers (Yukon-2) */
+ /* Bit 31: same as for Rx */
+enum {
+ BMU_TX_IPIDINCR_ON = 1<<13, /* Enable IP ID Increment */
+ BMU_TX_IPIDINCR_OFF = 1<<12, /* Disable IP ID Increment */
+ BMU_TX_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segment length mismatch */
+};
+
+/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
+/* PREF_UNIT_CTRL 32 bit Prefetch Control register */
+enum {
+ PREF_UNIT_OP_ON = 1<<3, /* prefetch unit operational */
+ PREF_UNIT_OP_OFF = 1<<2, /* prefetch unit not operational */
+ PREF_UNIT_RST_CLR = 1<<1, /* Clear Prefetch Unit Reset */
+ PREF_UNIT_RST_SET = 1<<0, /* Set Prefetch Unit Reset */
+};
+
+/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */
+/* RB_START 32 bit RAM Buffer Start Address */
+/* RB_END 32 bit RAM Buffer End Address */
+/* RB_WP 32 bit RAM Buffer Write Pointer */
+/* RB_RP 32 bit RAM Buffer Read Pointer */
+/* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */
+/* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */
+/* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */
+/* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */
+/* RB_PC 32 bit RAM Buffer Packet Counter */
+/* RB_LEV 32 bit RAM Buffer Level Register */
+
+#define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */
+/* RB_TST2 8 bit RAM Buffer Test Register 2 */
+/* RB_TST1 8 bit RAM Buffer Test Register 1 */
+
+/* RB_CTRL 8 bit RAM Buffer Control Register */
+enum {
+ RB_ENA_STFWD = 1<<5, /* Enable Store & Forward */
+ RB_DIS_STFWD = 1<<4, /* Disable Store & Forward */
+ RB_ENA_OP_MD = 1<<3, /* Enable Operation Mode */
+ RB_DIS_OP_MD = 1<<2, /* Disable Operation Mode */
+ RB_RST_CLR = 1<<1, /* Clear RAM Buf STM Reset */
+ RB_RST_SET = 1<<0, /* Set RAM Buf STM Reset */
+};
+
+
+/* Transmit GMAC FIFO (YUKON only) */
+enum {
+ TX_GMF_EA = 0x0d40,/* 32 bit Tx GMAC FIFO End Address */
+ TX_GMF_AE_THR = 0x0d44,/* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/
+ TX_GMF_CTRL_T = 0x0d48,/* 32 bit Tx GMAC FIFO Control/Test */
+
+ TX_GMF_WP = 0x0d60,/* 32 bit Tx GMAC FIFO Write Pointer */
+ TX_GMF_WSP = 0x0d64,/* 32 bit Tx GMAC FIFO Write Shadow Ptr. */
+ TX_GMF_WLEV = 0x0d68,/* 32 bit Tx GMAC FIFO Write Level */
+
+ TX_GMF_RP = 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */
+ TX_GMF_RSTP = 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */
+ TX_GMF_RLEV = 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */
+};
+
+/* Descriptor Poll Timer Registers */
+enum {
+ B28_DPT_INI = 0x0e00,/* 24 bit Descriptor Poll Timer Init Val */
+ B28_DPT_VAL = 0x0e04,/* 24 bit Descriptor Poll Timer Curr Val */
+ B28_DPT_CTRL = 0x0e08,/* 8 bit Descriptor Poll Timer Ctrl Reg */
+
+ B28_DPT_TST = 0x0e0a,/* 8 bit Descriptor Poll Timer Test Reg */
+};
+
+/* Time Stamp Timer Registers (YUKON only) */
+enum {
+ GMAC_TI_ST_VAL = 0x0e14,/* 32 bit Time Stamp Timer Curr Val */
+ GMAC_TI_ST_CTRL = 0x0e18,/* 8 bit Time Stamp Timer Ctrl Reg */
+ GMAC_TI_ST_TST = 0x0e1a,/* 8 bit Time Stamp Timer Test Reg */
+};
+
+/* Polling Unit Registers (Yukon-2 only) */
+enum {
+ POLL_CTRL = 0x0e20, /* 32 bit Polling Unit Control Reg */
+ POLL_LAST_IDX = 0x0e24,/* 16 bit Polling Unit List Last Index */
+
+ POLL_LIST_ADDR_LO= 0x0e28,/* 32 bit Poll. List Start Addr (low) */
+ POLL_LIST_ADDR_HI= 0x0e2c,/* 32 bit Poll. List Start Addr (high) */
+};
+
+/* ASF Subsystem Registers (Yukon-2 only) */
+enum {
+ B28_Y2_SMB_CONFIG = 0x0e40,/* 32 bit ASF SMBus Config Register */
+ B28_Y2_SMB_CSD_REG = 0x0e44,/* 32 bit ASF SMB Control/Status/Data */
+ B28_Y2_ASF_IRQ_V_BASE=0x0e60,/* 32 bit ASF IRQ Vector Base */
+
+ B28_Y2_ASF_STAT_CMD= 0x0e68,/* 32 bit ASF Status and Command Reg */
+ B28_Y2_ASF_HOST_COM= 0x0e6c,/* 32 bit ASF Host Communication Reg */
+ B28_Y2_DATA_REG_1 = 0x0e70,/* 32 bit ASF/Host Data Register 1 */
+ B28_Y2_DATA_REG_2 = 0x0e74,/* 32 bit ASF/Host Data Register 2 */
+ B28_Y2_DATA_REG_3 = 0x0e78,/* 32 bit ASF/Host Data Register 3 */
+ B28_Y2_DATA_REG_4 = 0x0e7c,/* 32 bit ASF/Host Data Register 4 */
+};
+
+/* Status BMU Registers (Yukon-2 only)*/
+enum {
+ STAT_CTRL = 0x0e80,/* 32 bit Status BMU Control Reg */
+ STAT_LAST_IDX = 0x0e84,/* 16 bit Status BMU Last Index */
+
+ STAT_LIST_ADDR_LO= 0x0e88,/* 32 bit Status List Start Addr (low) */
+ STAT_LIST_ADDR_HI= 0x0e8c,/* 32 bit Status List Start Addr (high) */
+ STAT_TXA1_RIDX = 0x0e90,/* 16 bit Status TxA1 Report Index Reg */
+ STAT_TXS1_RIDX = 0x0e92,/* 16 bit Status TxS1 Report Index Reg */
+ STAT_TXA2_RIDX = 0x0e94,/* 16 bit Status TxA2 Report Index Reg */
+ STAT_TXS2_RIDX = 0x0e96,/* 16 bit Status TxS2 Report Index Reg */
+ STAT_TX_IDX_TH = 0x0e98,/* 16 bit Status Tx Index Threshold Reg */
+ STAT_PUT_IDX = 0x0e9c,/* 16 bit Status Put Index Reg */
+
+/* FIFO Control/Status Registers (Yukon-2 only)*/
+ STAT_FIFO_WP = 0x0ea0,/* 8 bit Status FIFO Write Pointer Reg */
+ STAT_FIFO_RP = 0x0ea4,/* 8 bit Status FIFO Read Pointer Reg */
+ STAT_FIFO_RSP = 0x0ea6,/* 8 bit Status FIFO Read Shadow Ptr */
+ STAT_FIFO_LEVEL = 0x0ea8,/* 8 bit Status FIFO Level Reg */
+ STAT_FIFO_SHLVL = 0x0eaa,/* 8 bit Status FIFO Shadow Level Reg */
+ STAT_FIFO_WM = 0x0eac,/* 8 bit Status FIFO Watermark Reg */
+ STAT_FIFO_ISR_WM= 0x0ead,/* 8 bit Status FIFO ISR Watermark Reg */
+
+/* Level and ISR Timer Registers (Yukon-2 only)*/
+ STAT_LEV_TIMER_INI= 0x0eb0,/* 32 bit Level Timer Init. Value Reg */
+ STAT_LEV_TIMER_CNT= 0x0eb4,/* 32 bit Level Timer Counter Reg */
+ STAT_LEV_TIMER_CTRL= 0x0eb8,/* 8 bit Level Timer Control Reg */
+ STAT_LEV_TIMER_TEST= 0x0eb9,/* 8 bit Level Timer Test Reg */
+ STAT_TX_TIMER_INI = 0x0ec0,/* 32 bit Tx Timer Init. Value Reg */
+ STAT_TX_TIMER_CNT = 0x0ec4,/* 32 bit Tx Timer Counter Reg */
+ STAT_TX_TIMER_CTRL = 0x0ec8,/* 8 bit Tx Timer Control Reg */
+ STAT_TX_TIMER_TEST = 0x0ec9,/* 8 bit Tx Timer Test Reg */
+ STAT_ISR_TIMER_INI = 0x0ed0,/* 32 bit ISR Timer Init. Value Reg */
+ STAT_ISR_TIMER_CNT = 0x0ed4,/* 32 bit ISR Timer Counter Reg */
+ STAT_ISR_TIMER_CTRL= 0x0ed8,/* 8 bit ISR Timer Control Reg */
+ STAT_ISR_TIMER_TEST= 0x0ed9,/* 8 bit ISR Timer Test Reg */
+};
+
+enum {
+ LINKLED_OFF = 0x01,
+ LINKLED_ON = 0x02,
+ LINKLED_LINKSYNC_OFF = 0x04,
+ LINKLED_LINKSYNC_ON = 0x08,
+ LINKLED_BLINK_OFF = 0x10,
+ LINKLED_BLINK_ON = 0x20,
+};
+
+/* GMAC and GPHY Control Registers (YUKON only) */
+enum {
+ GMAC_CTRL = 0x0f00,/* 32 bit GMAC Control Reg */
+ GPHY_CTRL = 0x0f04,/* 32 bit GPHY Control Reg */
+ GMAC_IRQ_SRC = 0x0f08,/* 8 bit GMAC Interrupt Source Reg */
+ GMAC_IRQ_MSK = 0x0f0c,/* 8 bit GMAC Interrupt Mask Reg */
+ GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */
+
+/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
+
+ WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */
+
+ WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */
+ WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */
+ WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */
+ WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */
+ WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */
+ WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */
+ WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
+
+/* WOL Pattern Length Registers (YUKON only) */
+
+ WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */
+ WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */
+
+/* WOL Pattern Counter Registers (YUKON only) */
+
+
+ WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
+ WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
+};
+
+enum {
+ WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */
+ WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */
+};
+
+enum {
+ BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */
+ BASE_GMAC_2 = 0x3800,/* GMAC 2 registers */
+};
+
+/*
+ * Marvel-PHY Registers, indirect addressed over GMAC
+ */
+enum {
+ PHY_MARV_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
+ PHY_MARV_STAT = 0x01,/* 16 bit r/o PHY Status Register */
+ PHY_MARV_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
+ PHY_MARV_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
+ PHY_MARV_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
+ PHY_MARV_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
+ PHY_MARV_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
+ PHY_MARV_NEPG = 0x07,/* 16 bit r/w Next Page Register */
+ PHY_MARV_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
+ /* Marvel-specific registers */
+ PHY_MARV_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
+ PHY_MARV_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
+ PHY_MARV_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
+ PHY_MARV_PHY_CTRL = 0x10,/* 16 bit r/w PHY Specific Ctrl Reg */
+ PHY_MARV_PHY_STAT = 0x11,/* 16 bit r/o PHY Specific Stat Reg */
+ PHY_MARV_INT_MASK = 0x12,/* 16 bit r/w Interrupt Mask Reg */
+ PHY_MARV_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */
+ PHY_MARV_EXT_CTRL = 0x14,/* 16 bit r/w Ext. PHY Specific Ctrl */
+ PHY_MARV_RXE_CNT = 0x15,/* 16 bit r/w Receive Error Counter */
+ PHY_MARV_EXT_ADR = 0x16,/* 16 bit r/w Ext. Ad. for Cable Diag. */
+ PHY_MARV_PORT_IRQ = 0x17,/* 16 bit r/o Port 0 IRQ (88E1111 only) */
+ PHY_MARV_LED_CTRL = 0x18,/* 16 bit r/w LED Control Reg */
+ PHY_MARV_LED_OVER = 0x19,/* 16 bit r/w Manual LED Override Reg */
+ PHY_MARV_EXT_CTRL_2 = 0x1a,/* 16 bit r/w Ext. PHY Specific Ctrl 2 */
+ PHY_MARV_EXT_P_STAT = 0x1b,/* 16 bit r/w Ext. PHY Spec. Stat Reg */
+ PHY_MARV_CABLE_DIAG = 0x1c,/* 16 bit r/o Cable Diagnostic Reg */
+ PHY_MARV_PAGE_ADDR = 0x1d,/* 16 bit r/w Extended Page Address Reg */
+ PHY_MARV_PAGE_DATA = 0x1e,/* 16 bit r/w Extended Page Data Reg */
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+ PHY_MARV_FE_LED_PAR = 0x16,/* 16 bit r/w LED Parallel Select Reg. */
+ PHY_MARV_FE_LED_SER = 0x17,/* 16 bit r/w LED Stream Select S. LED */
+ PHY_MARV_FE_VCT_TX = 0x1a,/* 16 bit r/w VCT Reg. for TXP/N Pins */
+ PHY_MARV_FE_VCT_RX = 0x1b,/* 16 bit r/o VCT Reg. for RXP/N Pins */
+ PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */
+};
+
+enum {
+ PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */
+ PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */
+ PHY_CT_SPS_LSB = 1<<13, /* Bit 13: Speed select, lower bit */
+ PHY_CT_ANE = 1<<12, /* Bit 12: Auto-Negotiation Enabled */
+ PHY_CT_PDOWN = 1<<11, /* Bit 11: Power Down Mode */
+ PHY_CT_ISOL = 1<<10, /* Bit 10: Isolate Mode */
+ PHY_CT_RE_CFG = 1<<9, /* Bit 9: (sc) Restart Auto-Negotiation */
+ PHY_CT_DUP_MD = 1<<8, /* Bit 8: Duplex Mode */
+ PHY_CT_COL_TST = 1<<7, /* Bit 7: Collision Test enabled */
+ PHY_CT_SPS_MSB = 1<<6, /* Bit 6: Speed select, upper bit */
+};
+
+enum {
+ PHY_CT_SP1000 = PHY_CT_SPS_MSB, /* enable speed of 1000 Mbps */
+ PHY_CT_SP100 = PHY_CT_SPS_LSB, /* enable speed of 100 Mbps */
+ PHY_CT_SP10 = 0, /* enable speed of 10 Mbps */
+};
+
+enum {
+ PHY_ST_EXT_ST = 1<<8, /* Bit 8: Extended Status Present */
+
+ PHY_ST_PRE_SUP = 1<<6, /* Bit 6: Preamble Suppression */
+ PHY_ST_AN_OVER = 1<<5, /* Bit 5: Auto-Negotiation Over */
+ PHY_ST_REM_FLT = 1<<4, /* Bit 4: Remote Fault Condition Occured */
+ PHY_ST_AN_CAP = 1<<3, /* Bit 3: Auto-Negotiation Capability */
+ PHY_ST_LSYNC = 1<<2, /* Bit 2: Link Synchronized */
+ PHY_ST_JAB_DET = 1<<1, /* Bit 1: Jabber Detected */
+ PHY_ST_EXT_REG = 1<<0, /* Bit 0: Extended Register available */
+};
+
+enum {
+ PHY_I1_OUI_MSK = 0x3f<<10, /* Bit 15..10: Organization Unique ID */
+ PHY_I1_MOD_NUM = 0x3f<<4, /* Bit 9.. 4: Model Number */
+ PHY_I1_REV_MSK = 0xf, /* Bit 3.. 0: Revision Number */
+};
+
+/* different Marvell PHY Ids */
+enum {
+ PHY_MARV_ID0_VAL= 0x0141, /* Marvell Unique Identifier */
+
+ PHY_BCOM_ID1_A1 = 0x6041,
+ PHY_BCOM_ID1_B2 = 0x6043,
+ PHY_BCOM_ID1_C0 = 0x6044,
+ PHY_BCOM_ID1_C5 = 0x6047,
+
+ PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
+ PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */
+ PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
+ PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
+};
+
+/* Advertisement register bits */
+enum {
+ PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
+ PHY_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
+ PHY_AN_RF = 1<<13, /* Bit 13: Remote Fault Bits */
+
+ PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11: Try for asymmetric */
+ PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10: Try for pause */
+ PHY_AN_100BASE4 = 1<<9, /* Bit 9: Try for 100mbps 4k packets */
+ PHY_AN_100FULL = 1<<8, /* Bit 8: Try for 100mbps full-duplex */
+ PHY_AN_100HALF = 1<<7, /* Bit 7: Try for 100mbps half-duplex */
+ PHY_AN_10FULL = 1<<6, /* Bit 6: Try for 10mbps full-duplex */
+ PHY_AN_10HALF = 1<<5, /* Bit 5: Try for 10mbps half-duplex */
+ PHY_AN_CSMA = 1<<0, /* Bit 0: Only selector supported */
+ PHY_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
+ PHY_AN_FULL = PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA,
+ PHY_AN_ALL = PHY_AN_10HALF | PHY_AN_10FULL |
+ PHY_AN_100HALF | PHY_AN_100FULL,
+};
+
+/***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
+/***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
+enum {
+ PHY_B_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
+ PHY_B_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
+ PHY_B_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
+ PHY_B_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */
+ PHY_B_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */
+ PHY_B_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */
+ /* Bit 9..8: reserved */
+ PHY_B_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
+};
+
+/** Marvell-Specific */
+enum {
+ PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */
+ PHY_M_AN_ACK = 1<<14, /* (ro) Acknowledge Received */
+ PHY_M_AN_RF = 1<<13, /* Remote Fault */
+
+ PHY_M_AN_ASP = 1<<11, /* Asymmetric Pause */
+ PHY_M_AN_PC = 1<<10, /* MAC Pause implemented */
+ PHY_M_AN_100_T4 = 1<<9, /* Not cap. 100Base-T4 (always 0) */
+ PHY_M_AN_100_FD = 1<<8, /* Advertise 100Base-TX Full Duplex */
+ PHY_M_AN_100_HD = 1<<7, /* Advertise 100Base-TX Half Duplex */
+ PHY_M_AN_10_FD = 1<<6, /* Advertise 10Base-TX Full Duplex */
+ PHY_M_AN_10_HD = 1<<5, /* Advertise 10Base-TX Half Duplex */
+ PHY_M_AN_SEL_MSK =0x1f<<4, /* Bit 4.. 0: Selector Field Mask */
+};
+
+/* special defines for FIBER (88E1011S only) */
+enum {
+ PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */
+ PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */
+ PHY_M_AN_1000X_AHD = 1<<6, /* Advertise 10000Base-X Half Duplex */
+ PHY_M_AN_1000X_AFD = 1<<5, /* Advertise 10000Base-X Full Duplex */
+};
+
+/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
+enum {
+ PHY_M_P_NO_PAUSE_X = 0<<7,/* Bit 8.. 7: no Pause Mode */
+ PHY_M_P_SYM_MD_X = 1<<7, /* Bit 8.. 7: symmetric Pause Mode */
+ PHY_M_P_ASYM_MD_X = 2<<7,/* Bit 8.. 7: asymmetric Pause Mode */
+ PHY_M_P_BOTH_MD_X = 3<<7,/* Bit 8.. 7: both Pause Mode */
+};
+
+/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
+enum {
+ PHY_M_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
+ PHY_M_1000C_MSE = 1<<12, /* Manual Master/Slave Enable */
+ PHY_M_1000C_MSC = 1<<11, /* M/S Configuration (1=Master) */
+ PHY_M_1000C_MPD = 1<<10, /* Multi-Port Device */
+ PHY_M_1000C_AFD = 1<<9, /* Advertise Full Duplex */
+ PHY_M_1000C_AHD = 1<<8, /* Advertise Half Duplex */
+};
+
+/***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/
+enum {
+ PHY_M_PC_TX_FFD_MSK = 3<<14,/* Bit 15..14: Tx FIFO Depth Mask */
+ PHY_M_PC_RX_FFD_MSK = 3<<12,/* Bit 13..12: Rx FIFO Depth Mask */
+ PHY_M_PC_ASS_CRS_TX = 1<<11, /* Assert CRS on Transmit */
+ PHY_M_PC_FL_GOOD = 1<<10, /* Force Link Good */
+ PHY_M_PC_EN_DET_MSK = 3<<8,/* Bit 9.. 8: Energy Detect Mask */
+ PHY_M_PC_ENA_EXT_D = 1<<7, /* Enable Ext. Distance (10BT) */
+ PHY_M_PC_MDIX_MSK = 3<<5,/* Bit 6.. 5: MDI/MDIX Config. Mask */
+ PHY_M_PC_DIS_125CLK = 1<<4, /* Disable 125 CLK */
+ PHY_M_PC_MAC_POW_UP = 1<<3, /* MAC Power up */
+ PHY_M_PC_SQE_T_ENA = 1<<2, /* SQE Test Enabled */
+ PHY_M_PC_POL_R_DIS = 1<<1, /* Polarity Reversal Disabled */
+ PHY_M_PC_DIS_JABBER = 1<<0, /* Disable Jabber */
+};
+
+enum {
+ PHY_M_PC_EN_DET = 2<<8, /* Energy Detect (Mode 1) */
+ PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
+};
+
+#define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK)
+
+enum {
+ PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */
+ PHY_M_PC_MAN_MDIX = 1, /* 01 = Manual MDIX configuration */
+ PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */
+};
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+enum {
+ PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
+ PHY_M_PC_ENA_ENE_DT = 1<<14, /* Enable Energy Detect (sense & pulse) */
+ PHY_M_PC_DIS_NLP_CK = 1<<13, /* Disable Normal Link Puls (NLP) Check */
+ PHY_M_PC_ENA_LIP_NP = 1<<12, /* Enable Link Partner Next Page Reg. */
+ PHY_M_PC_DIS_NLP_GN = 1<<11, /* Disable Normal Link Puls Generation */
+
+ PHY_M_PC_DIS_SCRAMB = 1<<9, /* Disable Scrambler */
+ PHY_M_PC_DIS_FEFI = 1<<8, /* Disable Far End Fault Indic. (FEFI) */
+
+ PHY_M_PC_SH_TP_SEL = 1<<6, /* Shielded Twisted Pair Select */
+ PHY_M_PC_RX_FD_MSK = 3<<2,/* Bit 3.. 2: Rx FIFO Depth Mask */
+};
+
+/***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/
+enum {
+ PHY_M_PS_SPEED_MSK = 3<<14, /* Bit 15..14: Speed Mask */
+ PHY_M_PS_SPEED_1000 = 1<<15, /* 10 = 1000 Mbps */
+ PHY_M_PS_SPEED_100 = 1<<14, /* 01 = 100 Mbps */
+ PHY_M_PS_SPEED_10 = 0, /* 00 = 10 Mbps */
+ PHY_M_PS_FULL_DUP = 1<<13, /* Full Duplex */
+ PHY_M_PS_PAGE_REC = 1<<12, /* Page Received */
+ PHY_M_PS_SPDUP_RES = 1<<11, /* Speed & Duplex Resolved */
+ PHY_M_PS_LINK_UP = 1<<10, /* Link Up */
+ PHY_M_PS_CABLE_MSK = 7<<7, /* Bit 9.. 7: Cable Length Mask */
+ PHY_M_PS_MDI_X_STAT = 1<<6, /* MDI Crossover Stat (1=MDIX) */
+ PHY_M_PS_DOWNS_STAT = 1<<5, /* Downshift Status (1=downsh.) */
+ PHY_M_PS_ENDET_STAT = 1<<4, /* Energy Detect Status (1=act) */
+ PHY_M_PS_TX_P_EN = 1<<3, /* Tx Pause Enabled */
+ PHY_M_PS_RX_P_EN = 1<<2, /* Rx Pause Enabled */
+ PHY_M_PS_POL_REV = 1<<1, /* Polarity Reversed */
+ PHY_M_PS_JABBER = 1<<0, /* Jabber */
+};
+
+#define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN)
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+enum {
+ PHY_M_PS_DTE_DETECT = 1<<15, /* Data Terminal Equipment (DTE) Detected */
+ PHY_M_PS_RES_SPEED = 1<<14, /* Resolved Speed (1=100 Mbps, 0=10 Mbps */
+};
+
+enum {
+ PHY_M_IS_AN_ERROR = 1<<15, /* Auto-Negotiation Error */
+ PHY_M_IS_LSP_CHANGE = 1<<14, /* Link Speed Changed */
+ PHY_M_IS_DUP_CHANGE = 1<<13, /* Duplex Mode Changed */
+ PHY_M_IS_AN_PR = 1<<12, /* Page Received */
+ PHY_M_IS_AN_COMPL = 1<<11, /* Auto-Negotiation Completed */
+ PHY_M_IS_LST_CHANGE = 1<<10, /* Link Status Changed */
+ PHY_M_IS_SYMB_ERROR = 1<<9, /* Symbol Error */
+ PHY_M_IS_FALSE_CARR = 1<<8, /* False Carrier */
+ PHY_M_IS_FIFO_ERROR = 1<<7, /* FIFO Overflow/Underrun Error */
+ PHY_M_IS_MDI_CHANGE = 1<<6, /* MDI Crossover Changed */
+ PHY_M_IS_DOWNSH_DET = 1<<5, /* Downshift Detected */
+ PHY_M_IS_END_CHANGE = 1<<4, /* Energy Detect Changed */
+
+ PHY_M_IS_DTE_CHANGE = 1<<2, /* DTE Power Det. Status Changed */
+ PHY_M_IS_POL_CHANGE = 1<<1, /* Polarity Changed */
+ PHY_M_IS_JABBER = 1<<0, /* Jabber */
+
+ PHY_M_DEF_MSK = PHY_M_IS_LSP_CHANGE | PHY_M_IS_LST_CHANGE
+ | PHY_M_IS_FIFO_ERROR,
+ PHY_M_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL,
+};
+
+
+/***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/
+enum {
+ PHY_M_EC_ENA_BC_EXT = 1<<15, /* Enable Block Carr. Ext. (88E1111 only) */
+ PHY_M_EC_ENA_LIN_LB = 1<<14, /* Enable Line Loopback (88E1111 only) */
+
+ PHY_M_EC_DIS_LINK_P = 1<<12, /* Disable Link Pulses (88E1111 only) */
+ PHY_M_EC_M_DSC_MSK = 3<<10, /* Bit 11..10: Master Downshift Counter */
+ /* (88E1011 only) */
+ PHY_M_EC_S_DSC_MSK = 3<<8,/* Bit 9.. 8: Slave Downshift Counter */
+ /* (88E1011 only) */
+ PHY_M_EC_M_DSC_MSK2 = 7<<9,/* Bit 11.. 9: Master Downshift Counter */
+ /* (88E1111 only) */
+ PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */
+ /* !!! Errata in spec. (1 = disable) */
+ PHY_M_EC_RX_TIM_CT = 1<<7, /* RGMII Rx Timing Control*/
+ PHY_M_EC_MAC_S_MSK = 7<<4,/* Bit 6.. 4: Def. MAC interface speed */
+ PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */
+ PHY_M_EC_DTE_D_ENA = 1<<2, /* DTE Detect Enable (88E1111 only) */
+ PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
+ PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
+
+#define PHY_M_EC_M_DSC(x) ((x)<<10 & PHY_M_EC_M_DSC_MSK)
+ /* 00=1x; 01=2x; 10=3x; 11=4x */
+#define PHY_M_EC_S_DSC(x) ((x)<<8 & PHY_M_EC_S_DSC_MSK)
+ /* 00=dis; 01=1x; 10=2x; 11=3x */
+#define PHY_M_EC_DSC_2(x) ((x)<<9 & PHY_M_EC_M_DSC_MSK2)
+ /* 000=1x; 001=2x; 010=3x; 011=4x */
+#define PHY_M_EC_MAC_S(x) ((x)<<4 & PHY_M_EC_MAC_S_MSK)
+ /* 01X=0; 110=2.5; 111=25 (MHz) */
+
+/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
+enum {
+ PHY_M_PC_DIS_LINK_Pa = 1<<15,/* Disable Link Pulses */
+ PHY_M_PC_DSC_MSK = 7<<12,/* Bit 14..12: Downshift Counter */
+ PHY_M_PC_DOWN_S_ENA = 1<<11,/* Downshift Enable */
+};
+/* !!! Errata in spec. (1 = disable) */
+
+#define PHY_M_PC_DSC(x) (((x)<<12) & PHY_M_PC_DSC_MSK)
+ /* 100=5x; 101=6x; 110=7x; 111=8x */
+enum {
+ MAC_TX_CLK_0_MHZ = 2,
+ MAC_TX_CLK_2_5_MHZ = 6,
+ MAC_TX_CLK_25_MHZ = 7,
+};
+
+/***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/
+enum {
+ PHY_M_LEDC_DIS_LED = 1<<15, /* Disable LED */
+ PHY_M_LEDC_PULS_MSK = 7<<12,/* Bit 14..12: Pulse Stretch Mask */
+ PHY_M_LEDC_F_INT = 1<<11, /* Force Interrupt */
+ PHY_M_LEDC_BL_R_MSK = 7<<8,/* Bit 10.. 8: Blink Rate Mask */
+ PHY_M_LEDC_DP_C_LSB = 1<<7, /* Duplex Control (LSB, 88E1111 only) */
+ PHY_M_LEDC_TX_C_LSB = 1<<6, /* Tx Control (LSB, 88E1111 only) */
+ PHY_M_LEDC_LK_C_MSK = 7<<3,/* Bit 5.. 3: Link Control Mask */
+ /* (88E1111 only) */
+};
+
+enum {
+ PHY_M_LEDC_LINK_MSK = 3<<3,/* Bit 4.. 3: Link Control Mask */
+ /* (88E1011 only) */
+ PHY_M_LEDC_DP_CTRL = 1<<2, /* Duplex Control */
+ PHY_M_LEDC_DP_C_MSB = 1<<2, /* Duplex Control (MSB, 88E1111 only) */
+ PHY_M_LEDC_RX_CTRL = 1<<1, /* Rx Activity / Link */
+ PHY_M_LEDC_TX_CTRL = 1<<0, /* Tx Activity / Link */
+ PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */
+};
+
+#define PHY_M_LED_PULS_DUR(x) (((x)<<12) & PHY_M_LEDC_PULS_MSK)
+
+/***** PHY_MARV_PHY_STAT (page 3)16 bit r/w Polarity Control Reg. *****/
+enum {
+ PHY_M_POLC_LS1M_MSK = 0xf<<12, /* Bit 15..12: LOS,STAT1 Mix % Mask */
+ PHY_M_POLC_IS0M_MSK = 0xf<<8, /* Bit 11.. 8: INIT,STAT0 Mix % Mask */
+ PHY_M_POLC_LOS_MSK = 0x3<<6, /* Bit 7.. 6: LOS Pol. Ctrl. Mask */
+ PHY_M_POLC_INIT_MSK = 0x3<<4, /* Bit 5.. 4: INIT Pol. Ctrl. Mask */
+ PHY_M_POLC_STA1_MSK = 0x3<<2, /* Bit 3.. 2: STAT1 Pol. Ctrl. Mask */
+ PHY_M_POLC_STA0_MSK = 0x3, /* Bit 1.. 0: STAT0 Pol. Ctrl. Mask */
+};
+
+#define PHY_M_POLC_LS1_P_MIX(x) (((x)<<12) & PHY_M_POLC_LS1M_MSK)
+#define PHY_M_POLC_IS0_P_MIX(x) (((x)<<8) & PHY_M_POLC_IS0M_MSK)
+#define PHY_M_POLC_LOS_CTRL(x) (((x)<<6) & PHY_M_POLC_LOS_MSK)
+#define PHY_M_POLC_INIT_CTRL(x) (((x)<<4) & PHY_M_POLC_INIT_MSK)
+#define PHY_M_POLC_STA1_CTRL(x) (((x)<<2) & PHY_M_POLC_STA1_MSK)
+#define PHY_M_POLC_STA0_CTRL(x) (((x)<<0) & PHY_M_POLC_STA0_MSK)
+
+enum {
+ PULS_NO_STR = 0,/* no pulse stretching */
+ PULS_21MS = 1,/* 21 ms to 42 ms */
+ PULS_42MS = 2,/* 42 ms to 84 ms */
+ PULS_84MS = 3,/* 84 ms to 170 ms */
+ PULS_170MS = 4,/* 170 ms to 340 ms */
+ PULS_340MS = 5,/* 340 ms to 670 ms */
+ PULS_670MS = 6,/* 670 ms to 1.3 s */
+ PULS_1300MS = 7,/* 1.3 s to 2.7 s */
+};
+
+#define PHY_M_LED_BLINK_RT(x) (((x)<<8) & PHY_M_LEDC_BL_R_MSK)
+
+enum {
+ BLINK_42MS = 0,/* 42 ms */
+ BLINK_84MS = 1,/* 84 ms */
+ BLINK_170MS = 2,/* 170 ms */
+ BLINK_340MS = 3,/* 340 ms */
+ BLINK_670MS = 4,/* 670 ms */
+};
+
+/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
+#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
+ /* Bit 13..12: reserved */
+#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
+#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
+#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
+#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
+#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
+#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
+
+enum {
+ MO_LED_NORM = 0,
+ MO_LED_BLINK = 1,
+ MO_LED_OFF = 2,
+ MO_LED_ON = 3,
+};
+
+/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
+enum {
+ PHY_M_EC2_FI_IMPED = 1<<6, /* Fiber Input Impedance */
+ PHY_M_EC2_FO_IMPED = 1<<5, /* Fiber Output Impedance */
+ PHY_M_EC2_FO_M_CLK = 1<<4, /* Fiber Mode Clock Enable */
+ PHY_M_EC2_FO_BOOST = 1<<3, /* Fiber Output Boost */
+ PHY_M_EC2_FO_AM_MSK = 7,/* Bit 2.. 0: Fiber Output Amplitude */
+};
+
+/***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/
+enum {
+ PHY_M_FC_AUTO_SEL = 1<<15, /* Fiber/Copper Auto Sel. Dis. */
+ PHY_M_FC_AN_REG_ACC = 1<<14, /* Fiber/Copper AN Reg. Access */
+ PHY_M_FC_RESOLUTION = 1<<13, /* Fiber/Copper Resolution */
+ PHY_M_SER_IF_AN_BP = 1<<12, /* Ser. IF AN Bypass Enable */
+ PHY_M_SER_IF_BP_ST = 1<<11, /* Ser. IF AN Bypass Status */
+ PHY_M_IRQ_POLARITY = 1<<10, /* IRQ polarity */
+ PHY_M_DIS_AUT_MED = 1<<9, /* Disable Aut. Medium Reg. Selection */
+ /* (88E1111 only) */
+
+ PHY_M_UNDOC1 = 1<<7, /* undocumented bit !! */
+ PHY_M_DTE_POW_STAT = 1<<4, /* DTE Power Status (88E1111 only) */
+ PHY_M_MODE_MASK = 0xf, /* Bit 3.. 0: copy of HWCFG MODE[3:0] */
+};
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+/***** PHY_MARV_FE_LED_PAR 16 bit r/w LED Parallel Select Reg. *****/
+ /* Bit 15..12: reserved (used internally) */
+enum {
+ PHY_M_FELP_LED2_MSK = 0xf<<8, /* Bit 11.. 8: LED2 Mask (LINK) */
+ PHY_M_FELP_LED1_MSK = 0xf<<4, /* Bit 7.. 4: LED1 Mask (ACT) */
+ PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
+};
+
+#define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK)
+#define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK)
+#define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK)
+
+enum {
+ LED_PAR_CTRL_COLX = 0x00,
+ LED_PAR_CTRL_ERROR = 0x01,
+ LED_PAR_CTRL_DUPLEX = 0x02,
+ LED_PAR_CTRL_DP_COL = 0x03,
+ LED_PAR_CTRL_SPEED = 0x04,
+ LED_PAR_CTRL_LINK = 0x05,
+ LED_PAR_CTRL_TX = 0x06,
+ LED_PAR_CTRL_RX = 0x07,
+ LED_PAR_CTRL_ACT = 0x08,
+ LED_PAR_CTRL_LNK_RX = 0x09,
+ LED_PAR_CTRL_LNK_AC = 0x0a,
+ LED_PAR_CTRL_ACT_BL = 0x0b,
+ LED_PAR_CTRL_TX_BL = 0x0c,
+ LED_PAR_CTRL_RX_BL = 0x0d,
+ LED_PAR_CTRL_COL_BL = 0x0e,
+ LED_PAR_CTRL_INACT = 0x0f
+};
+
+/*****,PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/
+enum {
+ PHY_M_FESC_DIS_WAIT = 1<<2, /* Disable TDR Waiting Period */
+ PHY_M_FESC_ENA_MCLK = 1<<1, /* Enable MAC Rx Clock in sleep mode */
+ PHY_M_FESC_SEL_CL_A = 1<<0, /* Select Class A driver (100B-TX) */
+};
+
+/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
+/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
+enum {
+ PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
+ PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
+ PHY_M_MAC_MD_COPPER = 5,/* Copper only */
+ PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */
+};
+#define PHY_M_MAC_MODE_SEL(x) (((x)<<7) & PHY_M_MAC_MD_MSK)
+
+/***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/
+enum {
+ PHY_M_LEDC_LOS_MSK = 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */
+ PHY_M_LEDC_INIT_MSK = 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */
+ PHY_M_LEDC_STA1_MSK = 0xf<<4,/* Bit 7.. 4: STAT1 LED Ctrl. Mask */
+ PHY_M_LEDC_STA0_MSK = 0xf, /* Bit 3.. 0: STAT0 LED Ctrl. Mask */
+};
+
+#define PHY_M_LEDC_LOS_CTRL(x) (((x)<<12) & PHY_M_LEDC_LOS_MSK)
+#define PHY_M_LEDC_INIT_CTRL(x) (((x)<<8) & PHY_M_LEDC_INIT_MSK)
+#define PHY_M_LEDC_STA1_CTRL(x) (((x)<<4) & PHY_M_LEDC_STA1_MSK)
+#define PHY_M_LEDC_STA0_CTRL(x) (((x)<<0) & PHY_M_LEDC_STA0_MSK)
+
+/* GMAC registers */
+/* Port Registers */
+enum {
+ GM_GP_STAT = 0x0000, /* 16 bit r/o General Purpose Status */
+ GM_GP_CTRL = 0x0004, /* 16 bit r/w General Purpose Control */
+ GM_TX_CTRL = 0x0008, /* 16 bit r/w Transmit Control Reg. */
+ GM_RX_CTRL = 0x000c, /* 16 bit r/w Receive Control Reg. */
+ GM_TX_FLOW_CTRL = 0x0010, /* 16 bit r/w Transmit Flow-Control */
+ GM_TX_PARAM = 0x0014, /* 16 bit r/w Transmit Parameter Reg. */
+ GM_SERIAL_MODE = 0x0018, /* 16 bit r/w Serial Mode Register */
+/* Source Address Registers */
+ GM_SRC_ADDR_1L = 0x001c, /* 16 bit r/w Source Address 1 (low) */
+ GM_SRC_ADDR_1M = 0x0020, /* 16 bit r/w Source Address 1 (middle) */
+ GM_SRC_ADDR_1H = 0x0024, /* 16 bit r/w Source Address 1 (high) */
+ GM_SRC_ADDR_2L = 0x0028, /* 16 bit r/w Source Address 2 (low) */
+ GM_SRC_ADDR_2M = 0x002c, /* 16 bit r/w Source Address 2 (middle) */
+ GM_SRC_ADDR_2H = 0x0030, /* 16 bit r/w Source Address 2 (high) */
+
+/* Multicast Address Hash Registers */
+ GM_MC_ADDR_H1 = 0x0034, /* 16 bit r/w Multicast Address Hash 1 */
+ GM_MC_ADDR_H2 = 0x0038, /* 16 bit r/w Multicast Address Hash 2 */
+ GM_MC_ADDR_H3 = 0x003c, /* 16 bit r/w Multicast Address Hash 3 */
+ GM_MC_ADDR_H4 = 0x0040, /* 16 bit r/w Multicast Address Hash 4 */
+
+/* Interrupt Source Registers */
+ GM_TX_IRQ_SRC = 0x0044, /* 16 bit r/o Tx Overflow IRQ Source */
+ GM_RX_IRQ_SRC = 0x0048, /* 16 bit r/o Rx Overflow IRQ Source */
+ GM_TR_IRQ_SRC = 0x004c, /* 16 bit r/o Tx/Rx Over. IRQ Source */
+
+/* Interrupt Mask Registers */
+ GM_TX_IRQ_MSK = 0x0050, /* 16 bit r/w Tx Overflow IRQ Mask */
+ GM_RX_IRQ_MSK = 0x0054, /* 16 bit r/w Rx Overflow IRQ Mask */
+ GM_TR_IRQ_MSK = 0x0058, /* 16 bit r/w Tx/Rx Over. IRQ Mask */
+
+/* Serial Management Interface (SMI) Registers */
+ GM_SMI_CTRL = 0x0080, /* 16 bit r/w SMI Control Register */
+ GM_SMI_DATA = 0x0084, /* 16 bit r/w SMI Data Register */
+ GM_PHY_ADDR = 0x0088, /* 16 bit r/w GPHY Address Register */
+};
+
+/* MIB Counters */
+#define GM_MIB_CNT_BASE 0x0100 /* Base Address of MIB Counters */
+#define GM_MIB_CNT_SIZE 44 /* Number of MIB Counters */
+
+/*
+ * MIB Counters base address definitions (low word) -
+ * use offset 4 for access to high word (32 bit r/o)
+ */
+enum {
+ GM_RXF_UC_OK = GM_MIB_CNT_BASE + 0, /* Unicast Frames Received OK */
+ GM_RXF_BC_OK = GM_MIB_CNT_BASE + 8, /* Broadcast Frames Received OK */
+ GM_RXF_MPAUSE = GM_MIB_CNT_BASE + 16, /* Pause MAC Ctrl Frames Received */
+ GM_RXF_MC_OK = GM_MIB_CNT_BASE + 24, /* Multicast Frames Received OK */
+ GM_RXF_FCS_ERR = GM_MIB_CNT_BASE + 32, /* Rx Frame Check Seq. Error */
+ /* GM_MIB_CNT_BASE + 40: reserved */
+ GM_RXO_OK_LO = GM_MIB_CNT_BASE + 48, /* Octets Received OK Low */
+ GM_RXO_OK_HI = GM_MIB_CNT_BASE + 56, /* Octets Received OK High */
+ GM_RXO_ERR_LO = GM_MIB_CNT_BASE + 64, /* Octets Received Invalid Low */
+ GM_RXO_ERR_HI = GM_MIB_CNT_BASE + 72, /* Octets Received Invalid High */
+ GM_RXF_SHT = GM_MIB_CNT_BASE + 80, /* Frames <64 Byte Received OK */
+ GM_RXE_FRAG = GM_MIB_CNT_BASE + 88, /* Frames <64 Byte Received with FCS Err */
+ GM_RXF_64B = GM_MIB_CNT_BASE + 96, /* 64 Byte Rx Frame */
+ GM_RXF_127B = GM_MIB_CNT_BASE + 104, /* 65-127 Byte Rx Frame */
+ GM_RXF_255B = GM_MIB_CNT_BASE + 112, /* 128-255 Byte Rx Frame */
+ GM_RXF_511B = GM_MIB_CNT_BASE + 120, /* 256-511 Byte Rx Frame */
+ GM_RXF_1023B = GM_MIB_CNT_BASE + 128, /* 512-1023 Byte Rx Frame */
+ GM_RXF_1518B = GM_MIB_CNT_BASE + 136, /* 1024-1518 Byte Rx Frame */
+ GM_RXF_MAX_SZ = GM_MIB_CNT_BASE + 144, /* 1519-MaxSize Byte Rx Frame */
+ GM_RXF_LNG_ERR = GM_MIB_CNT_BASE + 152, /* Rx Frame too Long Error */
+ GM_RXF_JAB_PKT = GM_MIB_CNT_BASE + 160, /* Rx Jabber Packet Frame */
+ /* GM_MIB_CNT_BASE + 168: reserved */
+ GM_RXE_FIFO_OV = GM_MIB_CNT_BASE + 176, /* Rx FIFO overflow Event */
+ /* GM_MIB_CNT_BASE + 184: reserved */
+ GM_TXF_UC_OK = GM_MIB_CNT_BASE + 192, /* Unicast Frames Xmitted OK */
+ GM_TXF_BC_OK = GM_MIB_CNT_BASE + 200, /* Broadcast Frames Xmitted OK */
+ GM_TXF_MPAUSE = GM_MIB_CNT_BASE + 208, /* Pause MAC Ctrl Frames Xmitted */
+ GM_TXF_MC_OK = GM_MIB_CNT_BASE + 216, /* Multicast Frames Xmitted OK */
+ GM_TXO_OK_LO = GM_MIB_CNT_BASE + 224, /* Octets Transmitted OK Low */
+ GM_TXO_OK_HI = GM_MIB_CNT_BASE + 232, /* Octets Transmitted OK High */
+ GM_TXF_64B = GM_MIB_CNT_BASE + 240, /* 64 Byte Tx Frame */
+ GM_TXF_127B = GM_MIB_CNT_BASE + 248, /* 65-127 Byte Tx Frame */
+ GM_TXF_255B = GM_MIB_CNT_BASE + 256, /* 128-255 Byte Tx Frame */
+ GM_TXF_511B = GM_MIB_CNT_BASE + 264, /* 256-511 Byte Tx Frame */
+ GM_TXF_1023B = GM_MIB_CNT_BASE + 272, /* 512-1023 Byte Tx Frame */
+ GM_TXF_1518B = GM_MIB_CNT_BASE + 280, /* 1024-1518 Byte Tx Frame */
+ GM_TXF_MAX_SZ = GM_MIB_CNT_BASE + 288, /* 1519-MaxSize Byte Tx Frame */
+
+ GM_TXF_COL = GM_MIB_CNT_BASE + 304, /* Tx Collision */
+ GM_TXF_LAT_COL = GM_MIB_CNT_BASE + 312, /* Tx Late Collision */
+ GM_TXF_ABO_COL = GM_MIB_CNT_BASE + 320, /* Tx aborted due to Exces. Col. */
+ GM_TXF_MUL_COL = GM_MIB_CNT_BASE + 328, /* Tx Multiple Collision */
+ GM_TXF_SNG_COL = GM_MIB_CNT_BASE + 336, /* Tx Single Collision */
+ GM_TXE_FIFO_UR = GM_MIB_CNT_BASE + 344, /* Tx FIFO Underrun Event */
+};
+
+/* GMAC Bit Definitions */
+/* GM_GP_STAT 16 bit r/o General Purpose Status Register */
+enum {
+ GM_GPSR_SPEED = 1<<15, /* Bit 15: Port Speed (1 = 100 Mbps) */
+ GM_GPSR_DUPLEX = 1<<14, /* Bit 14: Duplex Mode (1 = Full) */
+ GM_GPSR_FC_TX_DIS = 1<<13, /* Bit 13: Tx Flow-Control Mode Disabled */
+ GM_GPSR_LINK_UP = 1<<12, /* Bit 12: Link Up Status */
+ GM_GPSR_PAUSE = 1<<11, /* Bit 11: Pause State */
+ GM_GPSR_TX_ACTIVE = 1<<10, /* Bit 10: Tx in Progress */
+ GM_GPSR_EXC_COL = 1<<9, /* Bit 9: Excessive Collisions Occured */
+ GM_GPSR_LAT_COL = 1<<8, /* Bit 8: Late Collisions Occured */
+
+ GM_GPSR_PHY_ST_CH = 1<<5, /* Bit 5: PHY Status Change */
+ GM_GPSR_GIG_SPEED = 1<<4, /* Bit 4: Gigabit Speed (1 = 1000 Mbps) */
+ GM_GPSR_PART_MODE = 1<<3, /* Bit 3: Partition mode */
+ GM_GPSR_FC_RX_DIS = 1<<2, /* Bit 2: Rx Flow-Control Mode Disabled */
+ GM_GPSR_PROM_EN = 1<<1, /* Bit 1: Promiscuous Mode Enabled */
+};
+
+/* GM_GP_CTRL 16 bit r/w General Purpose Control Register */
+enum {
+ GM_GPCR_PROM_ENA = 1<<14, /* Bit 14: Enable Promiscuous Mode */
+ GM_GPCR_FC_TX_DIS = 1<<13, /* Bit 13: Disable Tx Flow-Control Mode */
+ GM_GPCR_TX_ENA = 1<<12, /* Bit 12: Enable Transmit */
+ GM_GPCR_RX_ENA = 1<<11, /* Bit 11: Enable Receive */
+ GM_GPCR_BURST_ENA = 1<<10, /* Bit 10: Enable Burst Mode */
+ GM_GPCR_LOOP_ENA = 1<<9, /* Bit 9: Enable MAC Loopback Mode */
+ GM_GPCR_PART_ENA = 1<<8, /* Bit 8: Enable Partition Mode */
+ GM_GPCR_GIGS_ENA = 1<<7, /* Bit 7: Gigabit Speed (1000 Mbps) */
+ GM_GPCR_FL_PASS = 1<<6, /* Bit 6: Force Link Pass */
+ GM_GPCR_DUP_FULL = 1<<5, /* Bit 5: Full Duplex Mode */
+ GM_GPCR_FC_RX_DIS = 1<<4, /* Bit 4: Disable Rx Flow-Control Mode */
+ GM_GPCR_SPEED_100 = 1<<3, /* Bit 3: Port Speed 100 Mbps */
+ GM_GPCR_AU_DUP_DIS = 1<<2, /* Bit 2: Disable Auto-Update Duplex */
+ GM_GPCR_AU_FCT_DIS = 1<<1, /* Bit 1: Disable Auto-Update Flow-C. */
+ GM_GPCR_AU_SPD_DIS = 1<<0, /* Bit 0: Disable Auto-Update Speed */
+};
+
+#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
+#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
+
+/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
+enum {
+ GM_TXCR_FORCE_JAM = 1<<15, /* Bit 15: Force Jam / Flow-Control */
+ GM_TXCR_CRC_DIS = 1<<14, /* Bit 14: Disable insertion of CRC */
+ GM_TXCR_PAD_DIS = 1<<13, /* Bit 13: Disable padding of packets */
+ GM_TXCR_COL_THR_MSK = 1<<10, /* Bit 12..10: Collision Threshold */
+};
+
+#define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK)
+#define TX_COL_DEF 0x04
+
+/* GM_RX_CTRL 16 bit r/w Receive Control Register */
+enum {
+ GM_RXCR_UCF_ENA = 1<<15, /* Bit 15: Enable Unicast filtering */
+ GM_RXCR_MCF_ENA = 1<<14, /* Bit 14: Enable Multicast filtering */
+ GM_RXCR_CRC_DIS = 1<<13, /* Bit 13: Remove 4-byte CRC */
+ GM_RXCR_PASS_FC = 1<<12, /* Bit 12: Pass FC packets to FIFO */
+};
+
+/* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */
+enum {
+ GM_TXPA_JAMLEN_MSK = 0x03<<14, /* Bit 15..14: Jam Length */
+ GM_TXPA_JAMIPG_MSK = 0x1f<<9, /* Bit 13..9: Jam IPG */
+ GM_TXPA_JAMDAT_MSK = 0x1f<<4, /* Bit 8..4: IPG Jam to Data */
+ GM_TXPA_BO_LIM_MSK = 0x0f, /* Bit 3.. 0: Backoff Limit Mask */
+
+ TX_JAM_LEN_DEF = 0x03,
+ TX_JAM_IPG_DEF = 0x0b,
+ TX_IPG_JAM_DEF = 0x1c,
+ TX_BOF_LIM_DEF = 0x04,
+};
+
+#define TX_JAM_LEN_VAL(x) (((x)<<14) & GM_TXPA_JAMLEN_MSK)
+#define TX_JAM_IPG_VAL(x) (((x)<<9) & GM_TXPA_JAMIPG_MSK)
+#define TX_IPG_JAM_DATA(x) (((x)<<4) & GM_TXPA_JAMDAT_MSK)
+#define TX_BACK_OFF_LIM(x) ((x) & GM_TXPA_BO_LIM_MSK)
+
+
+/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
+enum {
+ GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */
+ GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */
+ GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */
+ GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
+ GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
+};
+
+#define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK)
+#define DATA_BLIND_DEF 0x04
+
+#define IPG_DATA_VAL(x) (x & GM_SMOD_IPG_MSK)
+#define IPG_DATA_DEF 0x1e
+
+/* GM_SMI_CTRL 16 bit r/w SMI Control Register */
+enum {
+ GM_SMI_CT_PHY_A_MSK = 0x1f<<11,/* Bit 15..11: PHY Device Address */
+ GM_SMI_CT_REG_A_MSK = 0x1f<<6,/* Bit 10.. 6: PHY Register Address */
+ GM_SMI_CT_OP_RD = 1<<5, /* Bit 5: OpCode Read (0=Write)*/
+ GM_SMI_CT_RD_VAL = 1<<4, /* Bit 4: Read Valid (Read completed) */
+ GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */
+};
+
+#define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
+#define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
+
+/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
+enum {
+ GM_PAR_MIB_CLR = 1<<5, /* Bit 5: Set MIB Clear Counter Mode */
+ GM_PAR_MIB_TST = 1<<4, /* Bit 4: MIB Load Counter (Test Mode) */
+};
+
+/* Receive Frame Status Encoding */
+enum {
+ GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */
+ GMR_FS_VLAN = 1<<13, /* VLAN Packet */
+ GMR_FS_JABBER = 1<<12, /* Jabber Packet */
+ GMR_FS_UN_SIZE = 1<<11, /* Undersize Packet */
+ GMR_FS_MC = 1<<10, /* Multicast Packet */
+ GMR_FS_BC = 1<<9, /* Broadcast Packet */
+ GMR_FS_RX_OK = 1<<8, /* Receive OK (Good Packet) */
+ GMR_FS_GOOD_FC = 1<<7, /* Good Flow-Control Packet */
+ GMR_FS_BAD_FC = 1<<6, /* Bad Flow-Control Packet */
+ GMR_FS_MII_ERR = 1<<5, /* MII Error */
+ GMR_FS_LONG_ERR = 1<<4, /* Too Long Packet */
+ GMR_FS_FRAGMENT = 1<<3, /* Fragment */
+
+ GMR_FS_CRC_ERR = 1<<1, /* CRC Error */
+ GMR_FS_RX_FF_OV = 1<<0, /* Rx FIFO Overflow */
+
+ GMR_FS_ANY_ERR = GMR_FS_RX_FF_OV | GMR_FS_CRC_ERR |
+ GMR_FS_FRAGMENT | GMR_FS_LONG_ERR |
+ GMR_FS_MII_ERR | GMR_FS_BAD_FC | GMR_FS_GOOD_FC |
+ GMR_FS_UN_SIZE | GMR_FS_JABBER,
+};
+
+/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
+enum {
+ RX_TRUNC_ON = 1<<27, /* enable packet truncation */
+ RX_TRUNC_OFF = 1<<26, /* disable packet truncation */
+ RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */
+ RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */
+
+ GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */
+ GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */
+ GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */
+
+ GMF_RP_TST_ON = 1<<10, /* Read Pointer Test On */
+ GMF_RP_TST_OFF = 1<<9, /* Read Pointer Test Off */
+ GMF_RP_STEP = 1<<8, /* Read Pointer Step/Increment */
+ GMF_RX_F_FL_ON = 1<<7, /* Rx FIFO Flush Mode On */
+ GMF_RX_F_FL_OFF = 1<<6, /* Rx FIFO Flush Mode Off */
+ GMF_CLI_RX_FO = 1<<5, /* Clear IRQ Rx FIFO Overrun */
+ GMF_CLI_RX_C = 1<<4, /* Clear IRQ Rx Frame Complete */
+
+ GMF_OPER_ON = 1<<3, /* Operational Mode On */
+ GMF_OPER_OFF = 1<<2, /* Operational Mode Off */
+ GMF_RST_CLR = 1<<1, /* Clear GMAC FIFO Reset */
+ GMF_RST_SET = 1<<0, /* Set GMAC FIFO Reset */
+
+ RX_GMF_FL_THR_DEF = 0xa, /* flush threshold (default) */
+
+ GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON,
+};
+
+
+/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
+enum {
+ TX_VLAN_TAG_ON = 1<<25,/* enable VLAN tagging */
+ TX_VLAN_TAG_OFF = 1<<24,/* disable VLAN tagging */
+
+ GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */
+ GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */
+ GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */
+
+ GMF_CLI_TX_FU = 1<<6, /* Clear IRQ Tx FIFO Underrun */
+ GMF_CLI_TX_FC = 1<<5, /* Clear IRQ Tx Frame Complete */
+ GMF_CLI_TX_PE = 1<<4, /* Clear IRQ Tx Parity Error */
+};
+
+/* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */
+enum {
+ GMT_ST_START = 1<<2, /* Start Time Stamp Timer */
+ GMT_ST_STOP = 1<<1, /* Stop Time Stamp Timer */
+ GMT_ST_CLR_IRQ = 1<<0, /* Clear Time Stamp Timer IRQ */
+};
+
+/* B28_Y2_ASF_STAT_CMD 32 bit ASF Status and Command Reg */
+enum {
+ Y2_ASF_OS_PRES = 1<<4, /* ASF operation system present */
+ Y2_ASF_RESET = 1<<3, /* ASF system in reset state */
+ Y2_ASF_RUNNING = 1<<2, /* ASF system operational */
+ Y2_ASF_CLR_HSTI = 1<<1, /* Clear ASF IRQ */
+ Y2_ASF_IRQ = 1<<0, /* Issue an IRQ to ASF system */
+
+ Y2_ASF_UC_STATE = 3<<2, /* ASF uC State */
+ Y2_ASF_CLK_HALT = 0, /* ASF system clock stopped */
+};
+
+/* B28_Y2_ASF_HOST_COM 32 bit ASF Host Communication Reg */
+enum {
+ Y2_ASF_CLR_ASFI = 1<<1, /* Clear host IRQ */
+ Y2_ASF_HOST_IRQ = 1<<0, /* Issue an IRQ to HOST system */
+};
+
+/* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */
+enum {
+ SC_STAT_CLR_IRQ = 1<<4, /* Status Burst IRQ clear */
+ SC_STAT_OP_ON = 1<<3, /* Operational Mode On */
+ SC_STAT_OP_OFF = 1<<2, /* Operational Mode Off */
+ SC_STAT_RST_CLR = 1<<1, /* Clear Status Unit Reset (Enable) */
+ SC_STAT_RST_SET = 1<<0, /* Set Status Unit Reset */
+};
+
+/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
+enum {
+ GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */
+ GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */
+ GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */
+ GMC_F_LOOPB_OFF = 1<<4, /* FIFO Loopback Off */
+ GMC_PAUSE_ON = 1<<3, /* Pause On */
+ GMC_PAUSE_OFF = 1<<2, /* Pause Off */
+ GMC_RST_CLR = 1<<1, /* Clear GMAC Reset */
+ GMC_RST_SET = 1<<0, /* Set GMAC Reset */
+};
+
+/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
+enum {
+ GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */
+ GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */
+ GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */
+ GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */
+ GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */
+ GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */
+ GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */
+ GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */
+ GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */
+ GPC_ANEG_0 = 1<<19, /* ANEG[0] */
+ GPC_ENA_XC = 1<<18, /* Enable MDI crossover */
+ GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */
+ GPC_ANEG_3 = 1<<16, /* ANEG[3] */
+ GPC_ANEG_2 = 1<<15, /* ANEG[2] */
+ GPC_ANEG_1 = 1<<14, /* ANEG[1] */
+ GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */
+ GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */
+ GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */
+ GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */
+ GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */
+ GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */
+ /* Bits 7..2: reserved */
+ GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */
+ GPC_RST_SET = 1<<0, /* Set GPHY Reset */
+};
+
+/* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */
+/* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */
+enum {
+ GM_IS_TX_CO_OV = 1<<5, /* Transmit Counter Overflow IRQ */
+ GM_IS_RX_CO_OV = 1<<4, /* Receive Counter Overflow IRQ */
+ GM_IS_TX_FF_UR = 1<<3, /* Transmit FIFO Underrun */
+ GM_IS_TX_COMPL = 1<<2, /* Frame Transmission Complete */
+ GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */
+ GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */
+
+#define GMAC_DEF_MSK GM_IS_TX_FF_UR
+
+/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
+ /* Bits 15.. 2: reserved */
+ GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */
+ GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */
+
+
+/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
+ WOL_CTL_LINK_CHG_OCC = 1<<15,
+ WOL_CTL_MAGIC_PKT_OCC = 1<<14,
+ WOL_CTL_PATTERN_OCC = 1<<13,
+ WOL_CTL_CLEAR_RESULT = 1<<12,
+ WOL_CTL_ENA_PME_ON_LINK_CHG = 1<<11,
+ WOL_CTL_DIS_PME_ON_LINK_CHG = 1<<10,
+ WOL_CTL_ENA_PME_ON_MAGIC_PKT = 1<<9,
+ WOL_CTL_DIS_PME_ON_MAGIC_PKT = 1<<8,
+ WOL_CTL_ENA_PME_ON_PATTERN = 1<<7,
+ WOL_CTL_DIS_PME_ON_PATTERN = 1<<6,
+ WOL_CTL_ENA_LINK_CHG_UNIT = 1<<5,
+ WOL_CTL_DIS_LINK_CHG_UNIT = 1<<4,
+ WOL_CTL_ENA_MAGIC_PKT_UNIT = 1<<3,
+ WOL_CTL_DIS_MAGIC_PKT_UNIT = 1<<2,
+ WOL_CTL_ENA_PATTERN_UNIT = 1<<1,
+ WOL_CTL_DIS_PATTERN_UNIT = 1<<0,
+};
+
+#define WOL_CTL_DEFAULT \
+ (WOL_CTL_DIS_PME_ON_LINK_CHG | \
+ WOL_CTL_DIS_PME_ON_PATTERN | \
+ WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
+ WOL_CTL_DIS_LINK_CHG_UNIT | \
+ WOL_CTL_DIS_PATTERN_UNIT | \
+ WOL_CTL_DIS_MAGIC_PKT_UNIT)
+
+/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
+#define WOL_CTL_PATT_ENA(x) (1 << (x))
+
+
+/* Control flags */
+enum {
+ UDPTCP = 1<<0,
+ CALSUM = 1<<1,
+ WR_SUM = 1<<2,
+ INIT_SUM= 1<<3,
+ LOCK_SUM= 1<<4,
+ INS_VLAN= 1<<5,
+ FRC_STAT= 1<<6,
+ EOP = 1<<7,
+};
+
+enum {
+ HW_OWNER = 1<<7,
+ OP_TCPWRITE = 0x11,
+ OP_TCPSTART = 0x12,
+ OP_TCPINIT = 0x14,
+ OP_TCPLCK = 0x18,
+ OP_TCPCHKSUM = OP_TCPSTART,
+ OP_TCPIS = OP_TCPINIT | OP_TCPSTART,
+ OP_TCPLW = OP_TCPLCK | OP_TCPWRITE,
+ OP_TCPLSW = OP_TCPLCK | OP_TCPSTART | OP_TCPWRITE,
+ OP_TCPLISW = OP_TCPLCK | OP_TCPINIT | OP_TCPSTART | OP_TCPWRITE,
+
+ OP_ADDR64 = 0x21,
+ OP_VLAN = 0x22,
+ OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN,
+ OP_LRGLEN = 0x24,
+ OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN,
+ OP_BUFFER = 0x40,
+ OP_PACKET = 0x41,
+ OP_LARGESEND = 0x43,
+
+/* YUKON-2 STATUS opcodes defines */
+ OP_RXSTAT = 0x60,
+ OP_RXTIMESTAMP = 0x61,
+ OP_RXVLAN = 0x62,
+ OP_RXCHKS = 0x64,
+ OP_RXCHKSVLAN = OP_RXCHKS | OP_RXVLAN,
+ OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN,
+ OP_RSS_HASH = 0x65,
+ OP_TXINDEXLE = 0x68,
+};
+
+/* Yukon 2 hardware interface
+ * Not tested on big endian
+ */
+struct sky2_tx_le {
+ union {
+ u32 addr;
+ struct {
+ u16 offset;
+ u16 start;
+ } csum __attribute((packed));
+ struct {
+ u16 size;
+ u16 rsvd;
+ } tso __attribute((packed));
+ } tx;
+ u16 length; /* also vlan tag or checksum start */
+ u8 ctrl;
+ u8 opcode;
+} __attribute((packed));
+
+struct sky2_rx_le {
+ u32 addr;
+ u16 length;
+ u8 ctrl;
+ u8 opcode;
+} __attribute((packed));;
+
+struct sky2_status_le {
+ u32 status; /* also checksum */
+ u16 length; /* also vlan tag */
+ u8 link;
+ u8 opcode;
+} __attribute((packed));
+
+struct ring_info {
+ struct sk_buff *skb;
+ dma_addr_t mapaddr;
+ u16 maplen;
+ u16 idx;
+};
+
+struct sky2_port {
+ struct sky2_hw *hw;
+ struct net_device *netdev;
+ unsigned port;
+ u32 msg_enable;
+
+ struct ring_info *tx_ring;
+ struct sky2_tx_le *tx_le;
+ spinlock_t tx_lock;
+ u32 tx_addr64;
+ u16 tx_cons; /* next le to check */
+ u16 tx_prod; /* next le to use */
+ u16 tx_pending;
+ u16 tx_last_put;
+ u16 tx_last_mss;
+
+ struct ring_info *rx_ring;
+ struct sky2_rx_le *rx_le;
+ u32 rx_addr64;
+ u16 rx_next; /* next re to check */
+ u16 rx_put; /* next le index to use */
+ u16 rx_pending;
+ u16 rx_last_put;
+#ifdef SKY2_VLAN_TAG_USED
+ u16 rx_tag;
+ struct vlan_group *vlgrp;
+#endif
+
+ dma_addr_t rx_le_map;
+ dma_addr_t tx_le_map;
+ u32 advertising; /* ADVERTISED_ bits */
+ u16 speed; /* SPEED_1000, SPEED_100, ... */
+ u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
+ u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
+ u8 rx_pause;
+ u8 tx_pause;
+ u8 rx_csum;
+ u8 wol;
+
+ struct tasklet_struct phy_task;
+ struct net_device_stats net_stats;
+};
+
+struct sky2_hw {
+ void __iomem *regs;
+ struct pci_dev *pdev;
+ u32 intr_mask;
+ struct net_device *dev[2];
+
+ int pm_cap;
+ u8 chip_id;
+ u8 chip_rev;
+ u8 copper;
+ u8 ports;
+
+ struct sky2_status_le *st_le;
+ u32 st_idx;
+ dma_addr_t st_dma;
+
+ spinlock_t phy_lock;
+};
+
+/* Register accessor for memory mapped device */
+static inline u32 sky2_read32(const struct sky2_hw *hw, unsigned reg)
+{
+ return readl(hw->regs + reg);
+}
+
+static inline u16 sky2_read16(const struct sky2_hw *hw, unsigned reg)
+{
+ return readw(hw->regs + reg);
+}
+
+static inline u8 sky2_read8(const struct sky2_hw *hw, unsigned reg)
+{
+ return readb(hw->regs + reg);
+}
+
+/* This should probably go away, bus based tweeks suck */
+static inline int is_pciex(const struct sky2_hw *hw)
+{
+ u32 status;
+ pci_read_config_dword(hw->pdev, PCI_DEV_STATUS, &status);
+ return (status & PCI_OS_PCI_X) == 0;
+}
+
+static inline void sky2_write32(const struct sky2_hw *hw, unsigned reg, u32 val)
+{
+ writel(val, hw->regs + reg);
+}
+
+static inline void sky2_write16(const struct sky2_hw *hw, unsigned reg, u16 val)
+{
+ writew(val, hw->regs + reg);
+}
+
+static inline void sky2_write8(const struct sky2_hw *hw, unsigned reg, u8 val)
+{
+ writeb(val, hw->regs + reg);
+}
+
+/* Yukon PHY related registers */
+#define SK_GMAC_REG(port,reg) \
+ (BASE_GMAC_1 + (port) * (BASE_GMAC_2-BASE_GMAC_1) + (reg))
+#define GM_PHY_RETRIES 100
+
+static inline u16 gma_read16(const struct sky2_hw *hw, unsigned port, unsigned reg)
+{
+ return sky2_read16(hw, SK_GMAC_REG(port,reg));
+}
+
+static inline u32 gma_read32(struct sky2_hw *hw, unsigned port, unsigned reg)
+{
+ unsigned base = SK_GMAC_REG(port, reg);
+ return (u32) sky2_read16(hw, base)
+ | (u32) sky2_read16(hw, base+4) << 16;
+}
+
+static inline void gma_write16(const struct sky2_hw *hw, unsigned port, int r, u16 v)
+{
+ sky2_write16(hw, SK_GMAC_REG(port,r), v);
+}
+
+static inline void gma_set_addr(struct sky2_hw *hw, unsigned port, unsigned reg,
+ const u8 *addr)
+{
+ gma_write16(hw, port, reg, (u16) addr[0] | ((u16) addr[1] << 8));
+ gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8));
+ gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8));
+}
+#endif
diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
index 936f8b76114..97bbca6b296 100644
--- a/include/linux/netdevice.h
+++ b/include/linux/netdevice.h
@@ -802,11 +802,15 @@ static inline u32 netif_msg_init(int debug_value, int default_msg_enable_bits)
}
/* Schedule rx intr now? */
+static inline int netif_rx_schedule_test(struct net_device *dev)
+{
+ return !test_and_set_bit(__LINK_STATE_RX_SCHED, &dev->state);
+}
+/* Schedule only if device is up */
static inline int netif_rx_schedule_prep(struct net_device *dev)
{
- return netif_running(dev) &&
- !test_and_set_bit(__LINK_STATE_RX_SCHED, &dev->state);
+ return netif_running(dev) && netif_rx_schedule_test(dev);
}
/* Add interface to tail of rx poll list. This assumes that _prep has
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 22:08:14 +0000