diff options
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_82598.c | 177 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_common.c | 138 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_common.h | 3 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_dcb_82598.c | 2 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_ethtool.c | 23 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_main.c | 77 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_type.h | 29 |
7 files changed, 327 insertions, 122 deletions
diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c index f726a14d1a7..525bd87fea5 100644 --- a/drivers/net/ixgbe/ixgbe_82598.c +++ b/drivers/net/ixgbe/ixgbe_82598.c @@ -255,104 +255,75 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw) } /** - * ixgbe_setup_fc_82598 - Configure flow control settings + * ixgbe_fc_enable_82598 - Enable flow control * @hw: pointer to hardware structure * @packetbuf_num: packet buffer number (0-7) * - * Configures the flow control settings based on SW configuration. This - * function is used for 802.3x flow control configuration only. + * Enable flow control according to the current settings. **/ -static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num) +static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) { - u32 frctl_reg; + s32 ret_val = 0; + u32 fctrl_reg; u32 rmcs_reg; + u32 reg; - if (packetbuf_num < 0 || packetbuf_num > 7) { - hw_dbg(hw, "Invalid packet buffer number [%d], expected range is" - " 0-7\n", packetbuf_num); - } - - frctl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL); - frctl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE); + fctrl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL); + fctrl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE); rmcs_reg = IXGBE_READ_REG(hw, IXGBE_RMCS); rmcs_reg &= ~(IXGBE_RMCS_TFCE_PRIORITY | IXGBE_RMCS_TFCE_802_3X); /* - * 10 gig parts do not have a word in the EEPROM to determine the - * default flow control setting, so we explicitly set it to full. - */ - if (hw->fc.type == ixgbe_fc_default) - hw->fc.type = ixgbe_fc_full; - - /* - * We want to save off the original Flow Control configuration just in - * case we get disconnected and then reconnected into a different hub - * or switch with different Flow Control capabilities. - */ - hw->fc.original_type = hw->fc.type; - - /* - * The possible values of the "flow_control" parameter are: + * The possible values of fc.current_mode are: * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames but not - * send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but we do not - * support receiving pause frames) + * 1: Rx flow control is enabled (we can receive pause frames, + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but + * we do not support receiving pause frames). * 3: Both Rx and Tx flow control (symmetric) are enabled. * other: Invalid. */ - switch (hw->fc.type) { + switch (hw->fc.current_mode) { case ixgbe_fc_none: + /* Flow control completely disabled by software override. */ break; case ixgbe_fc_rx_pause: /* - * Rx Flow control is enabled, - * and Tx Flow control is disabled. + * Rx Flow control is enabled and Tx Flow control is + * disabled by software override. Since there really + * isn't a way to advertise that we are capable of RX + * Pause ONLY, we will advertise that we support both + * symmetric and asymmetric Rx PAUSE. Later, we will + * disable the adapter's ability to send PAUSE frames. */ - frctl_reg |= IXGBE_FCTRL_RFCE; + fctrl_reg |= IXGBE_FCTRL_RFCE; break; case ixgbe_fc_tx_pause: /* - * Tx Flow control is enabled, and Rx Flow control is disabled, - * by a software over-ride. + * Tx Flow control is enabled, and Rx Flow control is + * disabled by software override. */ rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; break; case ixgbe_fc_full: - /* - * Flow control (both Rx and Tx) is enabled by a software - * over-ride. - */ - frctl_reg |= IXGBE_FCTRL_RFCE; + /* Flow control (both Rx and Tx) is enabled by SW override. */ + fctrl_reg |= IXGBE_FCTRL_RFCE; rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; break; default: - /* We should never get here. The value should be 0-3. */ hw_dbg(hw, "Flow control param set incorrectly\n"); + ret_val = -IXGBE_ERR_CONFIG; + goto out; break; } /* Enable 802.3x based flow control settings. */ - IXGBE_WRITE_REG(hw, IXGBE_FCTRL, frctl_reg); + IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl_reg); IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg); - /* - * Check for invalid software configuration, zeros are completely - * invalid for all parameters used past this point, and if we enable - * flow control with zero water marks, we blast flow control packets. - */ - if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) { - hw_dbg(hw, "Flow control structure initialized incorrectly\n"); - return IXGBE_ERR_INVALID_LINK_SETTINGS; - } - - /* - * We need to set up the Receive Threshold high and low water - * marks as well as (optionally) enabling the transmission of - * XON frames. - */ - if (hw->fc.type & ixgbe_fc_tx_pause) { + /* Set up and enable Rx high/low water mark thresholds, enable XON. */ + if (hw->fc.current_mode & ixgbe_fc_tx_pause) { if (hw->fc.send_xon) { IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), (hw->fc.low_water | IXGBE_FCRTL_XONE)); @@ -360,14 +331,93 @@ static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num) IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), hw->fc.low_water); } + IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), - (hw->fc.high_water)|IXGBE_FCRTH_FCEN); + (hw->fc.high_water | IXGBE_FCRTH_FCEN)); } - IXGBE_WRITE_REG(hw, IXGBE_FCTTV(0), hw->fc.pause_time); + /* Configure pause time (2 TCs per register) */ + reg = IXGBE_READ_REG(hw, IXGBE_FCTTV(packetbuf_num)); + if ((packetbuf_num & 1) == 0) + reg = (reg & 0xFFFF0000) | hw->fc.pause_time; + else + reg = (reg & 0x0000FFFF) | (hw->fc.pause_time << 16); + IXGBE_WRITE_REG(hw, IXGBE_FCTTV(packetbuf_num / 2), reg); + IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1)); - return 0; +out: + return ret_val; +} + +/** + * ixgbe_setup_fc_82598 - Configure flow control settings + * @hw: pointer to hardware structure + * @packetbuf_num: packet buffer number (0-7) + * + * Configures the flow control settings based on SW configuration. This + * function is used for 802.3x flow control configuration only. + **/ +static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num) +{ + s32 ret_val = 0; + ixgbe_link_speed speed; + bool link_up; + + /* Validate the packetbuf configuration */ + if (packetbuf_num < 0 || packetbuf_num > 7) { + hw_dbg(hw, "Invalid packet buffer number [%d], expected range is" + " 0-7\n", packetbuf_num); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + goto out; + } + + /* + * Validate the water mark configuration. Zero water marks are invalid + * because it causes the controller to just blast out fc packets. + */ + if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) { + hw_dbg(hw, "Invalid water mark configuration\n"); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + goto out; + } + + /* + * Validate the requested mode. Strict IEEE mode does not allow + * ixgbe_fc_rx_pause because it will cause testing anomalies. + */ + if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { + hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + goto out; + } + + /* + * 10gig parts do not have a word in the EEPROM to determine the + * default flow control setting, so we explicitly set it to full. + */ + if (hw->fc.requested_mode == ixgbe_fc_default) + hw->fc.requested_mode = ixgbe_fc_full; + + /* + * Save off the requested flow control mode for use later. Depending + * on the link partner's capabilities, we may or may not use this mode. + */ + + hw->fc.current_mode = hw->fc.requested_mode; + + /* Decide whether to use autoneg or not. */ + hw->mac.ops.check_link(hw, &speed, &link_up, false); + if (hw->phy.multispeed_fiber && (speed == IXGBE_LINK_SPEED_1GB_FULL)) + ret_val = ixgbe_fc_autoneg(hw); + + if (ret_val) + goto out; + + ret_val = ixgbe_fc_enable_82598(hw, packetbuf_num); + +out: + return ret_val; } /** @@ -414,7 +464,6 @@ static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw) * case we get disconnected and then reconnected into a different hub * or switch with different Flow Control capabilities. */ - hw->fc.original_type = hw->fc.type; ixgbe_setup_fc_82598(hw, 0); /* Add delay to filter out noises during initial link setup */ diff --git a/drivers/net/ixgbe/ixgbe_common.c b/drivers/net/ixgbe/ixgbe_common.c index 13ad5ba66b6..5ae93989784 100644 --- a/drivers/net/ixgbe/ixgbe_common.c +++ b/drivers/net/ixgbe/ixgbe_common.c @@ -1487,6 +1487,144 @@ s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw) } /** + * ixgbe_fc_autoneg - Configure flow control + * @hw: pointer to hardware structure + * + * Negotiates flow control capabilities with link partner using autoneg and + * applies the results. + **/ +s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw) +{ + s32 ret_val = 0; + u32 i, reg, pcs_anadv_reg, pcs_lpab_reg; + + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + + /* + * The possible values of fc.current_mode are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but + * we do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. + * other: Invalid. + */ + switch (hw->fc.current_mode) { + case ixgbe_fc_none: + /* Flow control completely disabled by software override. */ + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; + case ixgbe_fc_rx_pause: + /* + * Rx Flow control is enabled and Tx Flow control is + * disabled by software override. Since there really + * isn't a way to advertise that we are capable of RX + * Pause ONLY, we will advertise that we support both + * symmetric and asymmetric Rx PAUSE. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ + reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; + case ixgbe_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is + * disabled by software override. + */ + reg |= (IXGBE_PCS1GANA_ASM_PAUSE); + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); + break; + case ixgbe_fc_full: + /* Flow control (both Rx and Tx) is enabled by SW override. */ + reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; + default: + hw_dbg(hw, "Flow control param set incorrectly\n"); + ret_val = -IXGBE_ERR_CONFIG; + goto out; + break; + } + + IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); + + /* Set PCS register for autoneg */ + /* Enable and restart autoneg */ + reg |= IXGBE_PCS1GLCTL_AN_ENABLE | IXGBE_PCS1GLCTL_AN_RESTART; + + /* Disable AN timeout */ + if (hw->fc.strict_ieee) + reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; + + hw_dbg(hw, "Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg); + IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); + + /* See if autonegotiation has succeeded */ + hw->mac.autoneg_succeeded = 0; + for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) { + msleep(10); + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); + if ((reg & (IXGBE_PCS1GLSTA_LINK_OK | + IXGBE_PCS1GLSTA_AN_COMPLETE)) == + (IXGBE_PCS1GLSTA_LINK_OK | + IXGBE_PCS1GLSTA_AN_COMPLETE)) { + if (!(reg & IXGBE_PCS1GLSTA_AN_TIMED_OUT)) + hw->mac.autoneg_succeeded = 1; + break; + } + } + + if (!hw->mac.autoneg_succeeded) { + /* Autoneg failed to achieve a link, so we turn fc off */ + hw->fc.current_mode = ixgbe_fc_none; + hw_dbg(hw, "Flow Control = NONE.\n"); + goto out; + } + + /* + * Read the AN advertisement and LP ability registers and resolve + * local flow control settings accordingly + */ + pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP); + if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) { + /* + * Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.requested_mode == ixgbe_fc_full) { + hw->fc.current_mode = ixgbe_fc_full; + hw_dbg(hw, "Flow Control = FULL.\n"); + } else { + hw->fc.current_mode = ixgbe_fc_rx_pause; + hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); + } + } else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) && + (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) { + hw->fc.current_mode = ixgbe_fc_tx_pause; + hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n"); + } else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) && + !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) && + (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) { + hw->fc.current_mode = ixgbe_fc_rx_pause; + hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); + } else { + hw->fc.current_mode = ixgbe_fc_none; + hw_dbg(hw, "Flow Control = NONE.\n"); + } + +out: + return ret_val; +} + +/** * ixgbe_disable_pcie_master - Disable PCI-express master access * @hw: pointer to hardware structure * diff --git a/drivers/net/ixgbe/ixgbe_common.h b/drivers/net/ixgbe/ixgbe_common.h index 0b5ba575580..c63021261e5 100644 --- a/drivers/net/ixgbe/ixgbe_common.h +++ b/drivers/net/ixgbe/ixgbe_common.h @@ -61,6 +61,9 @@ s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, u8 *addr_list, u32 addr_count, ixgbe_mc_addr_itr func); s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw); s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw); +s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw, s32 packetbuf_num); +s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packtetbuf_num); +s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw); s32 ixgbe_validate_mac_addr(u8 *mac_addr); s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask); diff --git a/drivers/net/ixgbe/ixgbe_dcb_82598.c b/drivers/net/ixgbe/ixgbe_dcb_82598.c index 56032114893..df359554d49 100644 --- a/drivers/net/ixgbe/ixgbe_dcb_82598.c +++ b/drivers/net/ixgbe/ixgbe_dcb_82598.c @@ -298,7 +298,7 @@ s32 ixgbe_dcb_config_pfc_82598(struct ixgbe_hw *hw, reg = IXGBE_READ_REG(hw, IXGBE_RMCS); reg &= ~IXGBE_RMCS_TFCE_802_3X; /* correct the reporting of our flow control status */ - hw->fc.type = ixgbe_fc_none; + hw->fc.current_mode = ixgbe_fc_none; reg |= IXGBE_RMCS_TFCE_PRIORITY; IXGBE_WRITE_REG(hw, IXGBE_RMCS, reg); diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 54d96cb05b4..cec2f4e8c61 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -224,13 +224,13 @@ static void ixgbe_get_pauseparam(struct net_device *netdev, struct ixgbe_adapter *adapter = netdev_priv(netdev); struct ixgbe_hw *hw = &adapter->hw; - pause->autoneg = (hw->fc.type == ixgbe_fc_full ? 1 : 0); + pause->autoneg = (hw->fc.current_mode == ixgbe_fc_full ? 1 : 0); - if (hw->fc.type == ixgbe_fc_rx_pause) { + if (hw->fc.current_mode == ixgbe_fc_rx_pause) { pause->rx_pause = 1; - } else if (hw->fc.type == ixgbe_fc_tx_pause) { + } else if (hw->fc.current_mode == ixgbe_fc_tx_pause) { pause->tx_pause = 1; - } else if (hw->fc.type == ixgbe_fc_full) { + } else if (hw->fc.current_mode == ixgbe_fc_full) { pause->rx_pause = 1; pause->tx_pause = 1; } @@ -244,22 +244,17 @@ static int ixgbe_set_pauseparam(struct net_device *netdev, if ((pause->autoneg == AUTONEG_ENABLE) || (pause->rx_pause && pause->tx_pause)) - hw->fc.type = ixgbe_fc_full; + hw->fc.requested_mode = ixgbe_fc_full; else if (pause->rx_pause && !pause->tx_pause) - hw->fc.type = ixgbe_fc_rx_pause; + hw->fc.requested_mode = ixgbe_fc_rx_pause; else if (!pause->rx_pause && pause->tx_pause) - hw->fc.type = ixgbe_fc_tx_pause; + hw->fc.requested_mode = ixgbe_fc_tx_pause; else if (!pause->rx_pause && !pause->tx_pause) - hw->fc.type = ixgbe_fc_none; + hw->fc.requested_mode = ixgbe_fc_none; else return -EINVAL; - hw->fc.original_type = hw->fc.type; - - if (netif_running(netdev)) - ixgbe_reinit_locked(adapter); - else - ixgbe_reset(adapter); + hw->mac.ops.setup_fc(hw, 0); return 0; } diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index dceae37fd57..850361a4c38 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -1954,11 +1954,43 @@ static void ixgbe_configure(struct ixgbe_adapter *adapter) (adapter->rx_ring[i].count - 1)); } +/** + * ixgbe_link_config - set up initial link with default speed and duplex + * @hw: pointer to private hardware struct + * + * Returns 0 on success, negative on failure + **/ +static int ixgbe_link_config(struct ixgbe_hw *hw) +{ + u32 autoneg; + bool link_up = false; + u32 ret = IXGBE_ERR_LINK_SETUP; + + if (hw->mac.ops.check_link) + ret = hw->mac.ops.check_link(hw, &autoneg, &link_up, false); + + if (ret) + goto link_cfg_out; + + if (hw->mac.ops.get_link_capabilities) + ret = hw->mac.ops.get_link_capabilities(hw, &autoneg, + &hw->mac.autoneg); + if (ret) + goto link_cfg_out; + + if (hw->mac.ops.setup_link_speed) + ret = hw->mac.ops.setup_link_speed(hw, autoneg, true, link_up); + +link_cfg_out: + return ret; +} + static int ixgbe_up_complete(struct ixgbe_adapter *adapter) { struct net_device *netdev = adapter->netdev; struct ixgbe_hw *hw = &adapter->hw; int i, j = 0; + int err; int max_frame = netdev->mtu + ETH_HLEN + ETH_FCS_LEN; u32 txdctl, rxdctl, mhadd; u32 gpie; @@ -2039,6 +2071,10 @@ static int ixgbe_up_complete(struct ixgbe_adapter *adapter) ixgbe_irq_enable(adapter); + err = ixgbe_link_config(hw); + if (err) + dev_err(&adapter->pdev->dev, "link_config FAILED %d\n", err); + /* enable transmits */ netif_tx_start_all_queues(netdev); @@ -2792,8 +2828,7 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter) adapter->flags |= IXGBE_FLAG_FAN_FAIL_CAPABLE; /* default flow control settings */ - hw->fc.original_type = ixgbe_fc_none; - hw->fc.type = ixgbe_fc_none; + hw->fc.requested_mode = ixgbe_fc_none; hw->fc.high_water = IXGBE_DEFAULT_FCRTH; hw->fc.low_water = IXGBE_DEFAULT_FCRTL; hw->fc.pause_time = IXGBE_DEFAULT_FCPAUSE; @@ -3916,37 +3951,6 @@ static void ixgbe_netpoll(struct net_device *netdev) } #endif -/** - * ixgbe_link_config - set up initial link with default speed and duplex - * @hw: pointer to private hardware struct - * - * Returns 0 on success, negative on failure - **/ -static int ixgbe_link_config(struct ixgbe_hw *hw) -{ - u32 autoneg; - bool link_up = false; - u32 ret = IXGBE_ERR_LINK_SETUP; - - if (hw->mac.ops.check_link) - ret = hw->mac.ops.check_link(hw, &autoneg, &link_up, false); - - if (ret || !link_up) - goto link_cfg_out; - - if (hw->mac.ops.get_link_capabilities) - ret = hw->mac.ops.get_link_capabilities(hw, &autoneg, - &hw->mac.autoneg); - if (ret) - goto link_cfg_out; - - if (hw->mac.ops.setup_link_speed) - ret = hw->mac.ops.setup_link_speed(hw, autoneg, true, true); - -link_cfg_out: - return ret; -} - static const struct net_device_ops ixgbe_netdev_ops = { .ndo_open = ixgbe_open, .ndo_stop = ixgbe_close, @@ -4197,13 +4201,6 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev, /* reset the hardware with the new settings */ hw->mac.ops.start_hw(hw); - /* link_config depends on start_hw being called at least once */ - err = ixgbe_link_config(hw); - if (err) { - dev_err(&pdev->dev, "setup_link_speed FAILED %d\n", err); - goto err_register; - } - netif_carrier_off(netdev); strcpy(netdev->name, "eth%d"); diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h index 984b4ed372f..237c688f8b6 100644 --- a/drivers/net/ixgbe/ixgbe_type.h +++ b/drivers/net/ixgbe/ixgbe_type.h @@ -771,6 +771,28 @@ #define IXGBE_LINK_UP_TIME 90 /* 9.0 Seconds */ #define IXGBE_AUTO_NEG_TIME 45 /* 4.5 Seconds */ +#define FIBER_LINK_UP_LIMIT 50 + +/* PCS1GLSTA Bit Masks */ +#define IXGBE_PCS1GLSTA_LINK_OK 1 +#define IXGBE_PCS1GLSTA_SYNK_OK 0x10 +#define IXGBE_PCS1GLSTA_AN_COMPLETE 0x10000 +#define IXGBE_PCS1GLSTA_AN_PAGE_RX 0x20000 +#define IXGBE_PCS1GLSTA_AN_TIMED_OUT 0x40000 +#define IXGBE_PCS1GLSTA_AN_REMOTE_FAULT 0x80000 +#define IXGBE_PCS1GLSTA_AN_ERROR_RWS 0x100000 + +#define IXGBE_PCS1GANA_SYM_PAUSE 0x80 +#define IXGBE_PCS1GANA_ASM_PAUSE 0x100 + +/* PCS1GLCTL Bit Masks */ +#define IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN 0x00040000 /* PCS 1G autoneg to en */ +#define IXGBE_PCS1GLCTL_FLV_LINK_UP 1 +#define IXGBE_PCS1GLCTL_FORCE_LINK 0x20 +#define IXGBE_PCS1GLCTL_LOW_LINK_LATCH 0x40 +#define IXGBE_PCS1GLCTL_AN_ENABLE 0x10000 +#define IXGBE_PCS1GLCTL_AN_RESTART 0x20000 + /* SW Semaphore Register bitmasks */ #define IXGBE_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */ #define IXGBE_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */ @@ -1270,7 +1292,7 @@ enum ixgbe_media_type { }; /* Flow Control Settings */ -enum ixgbe_fc_type { +enum ixgbe_fc_mode { ixgbe_fc_none = 0, ixgbe_fc_rx_pause, ixgbe_fc_tx_pause, @@ -1294,8 +1316,8 @@ struct ixgbe_fc_info { u16 pause_time; /* Flow Control Pause timer */ bool send_xon; /* Flow control send XON */ bool strict_ieee; /* Strict IEEE mode */ - enum ixgbe_fc_type type; /* Type of flow control */ - enum ixgbe_fc_type original_type; + enum ixgbe_fc_mode current_mode; /* FC mode in effect */ + enum ixgbe_fc_mode requested_mode; /* FC mode requested by caller */ }; /* Statistics counters collected by the MAC */ @@ -1475,6 +1497,7 @@ struct ixgbe_phy_info { bool reset_disable; ixgbe_autoneg_advertised autoneg_advertised; bool autoneg_wait_to_complete; + bool multispeed_fiber; }; struct ixgbe_hw { |