diff options
| -rw-r--r-- | drivers/net/e1000e/e1000.h | 2 | ||||
| -rw-r--r-- | drivers/net/e1000e/ich8lan.c | 1 | ||||
| -rw-r--r-- | drivers/net/e1000e/netdev.c | 41 |
3 files changed, 32 insertions, 12 deletions
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h index 189dfa2d6c7..3e187b0e420 100644 --- a/drivers/net/e1000e/e1000.h +++ b/drivers/net/e1000e/e1000.h @@ -141,6 +141,8 @@ struct e1000_info; #define HV_TNCRS_UPPER PHY_REG(778, 29) /* Transmit with no CRS */ #define HV_TNCRS_LOWER PHY_REG(778, 30) +#define E1000_FCRTV_PCH 0x05F40 /* PCH Flow Control Refresh Timer Value */ + /* BM PHY Copper Specific Status */ #define BM_CS_STATUS 17 #define BM_CS_STATUS_LINK_UP 0x0400 diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 51ddb04ab19..92cf1033365 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -3558,6 +3558,7 @@ struct e1000_info e1000_pch_info = { | FLAG_HAS_AMT | FLAG_HAS_FLASH | FLAG_HAS_JUMBO_FRAMES + | FLAG_DISABLE_FC_PAUSE_TIME /* errata */ | FLAG_APME_IN_WUC, .pba = 26, .max_hw_frame_size = 4096, diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 0687c6aa4e4..a1a5a6f15a6 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -2769,25 +2769,38 @@ void e1000e_reset(struct e1000_adapter *adapter) /* * flow control settings * - * The high water mark must be low enough to fit two full frame + * The high water mark must be low enough to fit one full frame * (or the size used for early receive) above it in the Rx FIFO. * Set it to the lower of: * - 90% of the Rx FIFO size, and * - the full Rx FIFO size minus the early receive size (for parts * with ERT support assuming ERT set to E1000_ERT_2048), or - * - the full Rx FIFO size minus two full frames + * - the full Rx FIFO size minus one full frame */ - if ((adapter->flags & FLAG_HAS_ERT) && - (adapter->netdev->mtu > ETH_DATA_LEN)) - hwm = min(((pba << 10) * 9 / 10), - ((pba << 10) - (E1000_ERT_2048 << 3))); - else - hwm = min(((pba << 10) * 9 / 10), - ((pba << 10) - (2 * adapter->max_frame_size))); + if (hw->mac.type == e1000_pchlan) { + /* + * Workaround PCH LOM adapter hangs with certain network + * loads. If hangs persist, try disabling Tx flow control. + */ + if (adapter->netdev->mtu > ETH_DATA_LEN) { + fc->high_water = 0x3500; + fc->low_water = 0x1500; + } else { + fc->high_water = 0x5000; + fc->low_water = 0x3000; + } + } else { + if ((adapter->flags & FLAG_HAS_ERT) && + (adapter->netdev->mtu > ETH_DATA_LEN)) + hwm = min(((pba << 10) * 9 / 10), + ((pba << 10) - (E1000_ERT_2048 << 3))); + else + hwm = min(((pba << 10) * 9 / 10), + ((pba << 10) - adapter->max_frame_size)); - fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */ - fc->low_water = (fc->high_water - (2 * adapter->max_frame_size)); - fc->low_water &= E1000_FCRTL_RTL; /* 8-byte granularity */ + fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */ + fc->low_water = fc->high_water - 8; + } if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME) fc->pause_time = 0xFFFF; @@ -2813,6 +2826,10 @@ void e1000e_reset(struct e1000_adapter *adapter) if (mac->ops.init_hw(hw)) e_err("Hardware Error\n"); + /* additional part of the flow-control workaround above */ + if (hw->mac.type == e1000_pchlan) + ew32(FCRTV_PCH, 0x1000); + e1000_update_mng_vlan(adapter); /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */ |