diff options
| -rw-r--r-- | Documentation/feature-removal-schedule.txt | 10 | ||||
| -rw-r--r-- | Documentation/ide.txt | 49 | ||||
| -rw-r--r-- | drivers/ide/ide-cd.c | 30 | ||||
| -rw-r--r-- | drivers/ide/ide-disk.c | 5 | ||||
| -rw-r--r-- | drivers/ide/ide-dma.c | 52 | ||||
| -rw-r--r-- | drivers/ide/ide-probe.c | 3 | ||||
| -rw-r--r-- | drivers/ide/ide-tape.c | 5 | ||||
| -rw-r--r-- | drivers/ide/ide.c | 20 | ||||
| -rw-r--r-- | drivers/ide/legacy/qd65xx.c | 43 | ||||
| -rw-r--r-- | drivers/ide/pci/cmd640.c | 3 | ||||
| -rw-r--r-- | drivers/ide/pci/hpt366.c | 12 |
11 files changed, 54 insertions, 178 deletions
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 4d3aa519ead..ba899ff2a8f 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -172,6 +172,16 @@ Who: Len Brown <len.brown@intel.com> --------------------------- +What: ide-tape driver +When: July 2008 +Files: drivers/ide/ide-tape.c +Why: This driver might not have any users anymore and maintaining it for no + reason is an effort no one wants to make. +Who: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>, Borislav Petkov + <petkovbb@googlemail.com> + +--------------------------- + What: libata spindown skipping and warning When: Dec 2008 Why: Some halt(8) implementations synchronize caches for and spin diff --git a/Documentation/ide.txt b/Documentation/ide.txt index 94e2e3b9e77..bcd7cd1278e 100644 --- a/Documentation/ide.txt +++ b/Documentation/ide.txt @@ -258,8 +258,6 @@ Summary of ide driver parameters for kernel command line As for VLB, it is safest to not specify it. Bigger values are safer than smaller ones. - "idex=noprobe" : do not attempt to access/use this interface - "idex=base" : probe for an interface at the addr specified, where "base" is usually 0x1f0 or 0x170 and "ctl" is assumed to be "base"+0x206 @@ -309,53 +307,6 @@ are detected automatically). ================================================================================ -IDE ATAPI streaming tape driver -------------------------------- - -This driver is a part of the Linux ide driver and works in co-operation -with linux/drivers/block/ide.c. - -The driver, in co-operation with ide.c, basically traverses the -request-list for the block device interface. The character device -interface, on the other hand, creates new requests, adds them -to the request-list of the block device, and waits for their completion. - -Pipelined operation mode is now supported on both reads and writes. - -The block device major and minor numbers are determined from the -tape's relative position in the ide interfaces, as explained in ide.c. - -The character device interface consists of the following devices: - - ht0 major 37, minor 0 first IDE tape, rewind on close. - ht1 major 37, minor 1 second IDE tape, rewind on close. - ... - nht0 major 37, minor 128 first IDE tape, no rewind on close. - nht1 major 37, minor 129 second IDE tape, no rewind on close. - ... - -Run /dev/MAKEDEV to create the above entries. - -The general magnetic tape commands compatible interface, as defined by -include/linux/mtio.h, is accessible through the character device. - -General ide driver configuration options, such as the interrupt-unmask -flag, can be configured by issuing an ioctl to the block device interface, -as any other ide device. - -Our own ide-tape ioctl's can be issued to either the block device or -the character device interface. - -Maximal throughput with minimal bus load will usually be achieved in the -following scenario: - - 1. ide-tape is operating in the pipelined operation mode. - 2. No buffering is performed by the user backup program. - - - -================================================================================ - Some Terminology ---------------- IDE = Integrated Drive Electronics, meaning that each drive has a built-in diff --git a/drivers/ide/ide-cd.c b/drivers/ide/ide-cd.c index 310e497b583..c8d0e871599 100644 --- a/drivers/ide/ide-cd.c +++ b/drivers/ide/ide-cd.c @@ -670,8 +670,8 @@ static void cdrom_buffer_sectors (ide_drive_t *drive, unsigned long sector, * and attempt to recover if there are problems. Returns 0 if everything's * ok; nonzero if the request has been terminated. */ -static -int ide_cd_check_ireason(ide_drive_t *drive, int len, int ireason, int rw) +static int ide_cd_check_ireason(ide_drive_t *drive, struct request *rq, + int len, int ireason, int rw) { /* * ireason == 0: the drive wants to receive data from us @@ -701,6 +701,9 @@ int ide_cd_check_ireason(ide_drive_t *drive, int len, int ireason, int rw) drive->name, __FUNCTION__, ireason); } + if (rq->cmd_type == REQ_TYPE_ATA_PC) + rq->cmd_flags |= REQ_FAILED; + cdrom_end_request(drive, 0); return -1; } @@ -1071,11 +1074,11 @@ static ide_startstop_t cdrom_newpc_intr(ide_drive_t *drive) /* * check which way to transfer data */ - if (blk_fs_request(rq) || blk_pc_request(rq)) { - if (ide_cd_check_ireason(drive, len, ireason, write)) - return ide_stopped; + if (ide_cd_check_ireason(drive, rq, len, ireason, write)) + return ide_stopped; - if (blk_fs_request(rq) && write == 0) { + if (blk_fs_request(rq)) { + if (write == 0) { int nskip; if (ide_cd_check_transfer_size(drive, len)) { @@ -1101,16 +1104,9 @@ static ide_startstop_t cdrom_newpc_intr(ide_drive_t *drive) if (ireason == 0) { write = 1; xferfunc = HWIF(drive)->atapi_output_bytes; - } else if (ireason == 2 || (ireason == 1 && - (blk_fs_request(rq) || blk_pc_request(rq)))) { + } else { write = 0; xferfunc = HWIF(drive)->atapi_input_bytes; - } else { - printk(KERN_ERR "%s: %s: The drive " - "appears confused (ireason = 0x%02x). " - "Trying to recover by ending request.\n", - drive->name, __FUNCTION__, ireason); - goto end_request; } /* @@ -1182,11 +1178,10 @@ static ide_startstop_t cdrom_newpc_intr(ide_drive_t *drive) else rq->data += blen; } + if (!write && blk_sense_request(rq)) + rq->sense_len += blen; } - if (write && blk_sense_request(rq)) - rq->sense_len += thislen; - /* * pad, if necessary */ @@ -1931,6 +1926,7 @@ static const struct cd_list_entry ide_cd_quirks_list[] = { { "MATSHITADVD-ROM SR-8186", NULL, IDE_CD_FLAG_PLAY_AUDIO_OK }, { "MATSHITADVD-ROM SR-8176", NULL, IDE_CD_FLAG_PLAY_AUDIO_OK }, { "MATSHITADVD-ROM SR-8174", NULL, IDE_CD_FLAG_PLAY_AUDIO_OK }, + { "Optiarc DVD RW AD-5200A", NULL, IDE_CD_FLAG_PLAY_AUDIO_OK }, { NULL, NULL, 0 } }; diff --git a/drivers/ide/ide-disk.c b/drivers/ide/ide-disk.c index 8f5bed47105..39501d13025 100644 --- a/drivers/ide/ide-disk.c +++ b/drivers/ide/ide-disk.c @@ -867,7 +867,7 @@ static void idedisk_setup (ide_drive_t *drive) /* Only print cache size when it was specified */ if (id->buf_size) - printk (" w/%dKiB Cache", id->buf_size/2); + printk(KERN_CONT " w/%dKiB Cache", id->buf_size / 2); printk(KERN_CONT ", CHS=%d/%d/%d\n", drive->bios_cyl, drive->bios_head, drive->bios_sect); @@ -949,7 +949,8 @@ static void ide_device_shutdown(ide_drive_t *drive) return; } - printk("Shutdown: %s\n", drive->name); + printk(KERN_INFO "Shutdown: %s\n", drive->name); + drive->gendev.bus->suspend(&drive->gendev, PMSG_SUSPEND); } diff --git a/drivers/ide/ide-dma.c b/drivers/ide/ide-dma.c index d0e7b537353..2de99e4be5c 100644 --- a/drivers/ide/ide-dma.c +++ b/drivers/ide/ide-dma.c @@ -1,9 +1,13 @@ /* + * IDE DMA support (including IDE PCI BM-DMA). + * * Copyright (C) 1995-1998 Mark Lord * Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org> * Copyright (C) 2004, 2007 Bartlomiej Zolnierkiewicz * * May be copied or modified under the terms of the GNU General Public License + * + * DMA is supported for all IDE devices (disk drives, cdroms, tapes, floppies). */ /* @@ -11,49 +15,6 @@ */ /* - * This module provides support for the bus-master IDE DMA functions - * of various PCI chipsets, including the Intel PIIX (i82371FB for - * the 430 FX chipset), the PIIX3 (i82371SB for the 430 HX/VX and - * 440 chipsets), and the PIIX4 (i82371AB for the 430 TX chipset) - * ("PIIX" stands for "PCI ISA IDE Xcellerator"). - * - * Pretty much the same code works for other IDE PCI bus-mastering chipsets. - * - * DMA is supported for all IDE devices (disk drives, cdroms, tapes, floppies). - * - * By default, DMA support is prepared for use, but is currently enabled only - * for drives which already have DMA enabled (UltraDMA or mode 2 multi/single), - * or which are recognized as "good" (see table below). Drives with only mode0 - * or mode1 (multi/single) DMA should also work with this chipset/driver - * (eg. MC2112A) but are not enabled by default. - * - * Use "hdparm -i" to view modes supported by a given drive. - * - * The hdparm-3.5 (or later) utility can be used for manually enabling/disabling - * DMA support, but must be (re-)compiled against this kernel version or later. - * - * To enable DMA, use "hdparm -d1 /dev/hd?" on a per-drive basis after booting. - * If problems arise, ide.c will disable DMA operation after a few retries. - * This error recovery mechanism works and has been extremely well exercised. - * - * IDE drives, depending on their vintage, may support several different modes - * of DMA operation. The boot-time modes are indicated with a "*" in - * the "hdparm -i" listing, and can be changed with *knowledgeable* use of - * the "hdparm -X" feature. There is seldom a need to do this, as drives - * normally power-up with their "best" PIO/DMA modes enabled. - * - * Testing has been done with a rather extensive number of drives, - * with Quantum & Western Digital models generally outperforming the pack, - * and Fujitsu & Conner (and some Seagate which are really Conner) drives - * showing more lackluster throughput. - * - * Keep an eye on /var/adm/messages for "DMA disabled" messages. - * - * Some people have reported trouble with Intel Zappa motherboards. - * This can be fixed by upgrading the AMI BIOS to version 1.00.04.BS0, - * available from ftp://ftp.intel.com/pub/bios/10004bs0.exe - * (thanks to Glen Morrell <glen@spin.Stanford.edu> for researching this). - * * Thanks to "Christopher J. Reimer" <reimer@doe.carleton.ca> for * fixing the problem with the BIOS on some Acer motherboards. * @@ -65,11 +26,6 @@ * * Most importantly, thanks to Robert Bringman <rob@mars.trion.com> * for supplying a Promise UDMA board & WD UDMA drive for this work! - * - * And, yes, Intel Zappa boards really *do* use both PIIX IDE ports. - * - * ATA-66/100 and recovery functions, I forgot the rest...... - * */ #include <linux/module.h> diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c index 4a2cb286822..194ecb0049e 100644 --- a/drivers/ide/ide-probe.c +++ b/drivers/ide/ide-probe.c @@ -756,7 +756,8 @@ static int ide_probe_port(ide_hwif_t *hwif) BUG_ON(hwif->present); - if (hwif->noprobe) + if (hwif->noprobe || + (hwif->drives[0].noprobe && hwif->drives[1].noprobe)) return -EACCES; /* diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c index 0598ecfd5f3..43e0e055777 100644 --- a/drivers/ide/ide-tape.c +++ b/drivers/ide/ide-tape.c @@ -3765,6 +3765,11 @@ static int ide_tape_probe(ide_drive_t *drive) g->fops = &idetape_block_ops; ide_register_region(g); + printk(KERN_WARNING "It is possible that this driver does not have any" + " users anymore and, as a result, it will be REMOVED soon." + " Please notify Bart <bzolnier@gmail.com> or Boris" + " <petkovbb@gmail.com> in case you still need it.\n"); + return 0; out_free_tape: diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c index 477833f0daf..fa16bc30bbc 100644 --- a/drivers/ide/ide.c +++ b/drivers/ide/ide.c @@ -590,11 +590,6 @@ void ide_unregister(unsigned int index, int init_default, int restore) hwif->extra_ports = 0; } - /* - * Note that we only release the standard ports, - * and do not even try to handle any extra ports - * allocated for weird IDE interface chipsets. - */ ide_hwif_release_regions(hwif); /* copy original settings */ @@ -1036,10 +1031,9 @@ int generic_ide_ioctl(ide_drive_t *drive, struct file *file, struct block_device drive->nice1 = (arg >> IDE_NICE_1) & 1; return 0; case HDIO_DRIVE_RESET: - { - unsigned long flags; - if (!capable(CAP_SYS_ADMIN)) return -EACCES; - + if (!capable(CAP_SYS_ADMIN)) + return -EACCES; + /* * Abort the current command on the * group if there is one, taking @@ -1058,17 +1052,15 @@ int generic_ide_ioctl(ide_drive_t *drive, struct file *file, struct block_device ide_abort(drive, "drive reset"); BUG_ON(HWGROUP(drive)->handler); - + /* Ensure nothing gets queued after we drop the lock. Reset will clear the busy */ - + HWGROUP(drive)->busy = 1; spin_unlock_irqrestore(&ide_lock, flags); (void) ide_do_reset(drive); return 0; - } - case HDIO_GET_BUSSTATE: if (!capable(CAP_SYS_ADMIN)) return -EACCES; @@ -1449,7 +1441,7 @@ static int __init ide_setup(char *s) case -1: /* "noprobe" */ hwif->noprobe = 1; - goto done; + goto obsolete_option; case 1: /* base */ vals[1] = vals[0] + 0x206; /* default ctl */ diff --git a/drivers/ide/legacy/qd65xx.c b/drivers/ide/legacy/qd65xx.c index bba29df5f21..2f4f47ad602 100644 --- a/drivers/ide/legacy/qd65xx.c +++ b/drivers/ide/legacy/qd65xx.c @@ -334,43 +334,6 @@ static void __init qd6580_port_init_devs(ide_hwif_t *hwif) hwif->drives[1].drive_data = t2; } -/* - * qd_unsetup: - * - * called to unsetup an ata channel : back to default values, unlinks tuning - */ -/* -static void __exit qd_unsetup(ide_hwif_t *hwif) -{ - u8 config = hwif->config_data; - int base = hwif->select_data; - void *set_pio_mode = (void *)hwif->set_pio_mode; - - if (hwif->chipset != ide_qd65xx) - return; - - printk(KERN_NOTICE "%s: back to defaults\n", hwif->name); - - hwif->selectproc = NULL; - hwif->set_pio_mode = NULL; - - if (set_pio_mode == (void *)qd6500_set_pio_mode) { - // will do it for both - outb(QD6500_DEF_DATA, QD_TIMREG(&hwif->drives[0])); - } else if (set_pio_mode == (void *)qd6580_set_pio_mode) { - if (QD_CONTROL(hwif) & QD_CONTR_SEC_DISABLED) { - outb(QD6580_DEF_DATA, QD_TIMREG(&hwif->drives[0])); - outb(QD6580_DEF_DATA2, QD_TIMREG(&hwif->drives[1])); - } else { - outb(hwif->channel ? QD6580_DEF_DATA2 : QD6580_DEF_DATA, QD_TIMREG(&hwif->drives[0])); - } - } else { - printk(KERN_WARNING "Unknown qd65xx tuning fonction !\n"); - printk(KERN_WARNING "keeping settings !\n"); - } -} -*/ - static const struct ide_port_info qd65xx_port_info __initdata = { .chipset = ide_qd65xx, .host_flags = IDE_HFLAG_IO_32BIT | @@ -444,6 +407,8 @@ static int __init qd_probe(int base) printk(KERN_DEBUG "qd6580: config=%#x, control=%#x, ID3=%u\n", config, control, QD_ID3); + outb(QD_DEF_CONTR, QD_CONTROL_PORT); + if (control & QD_CONTR_SEC_DISABLED) { /* secondary disabled */ @@ -460,8 +425,6 @@ static int __init qd_probe(int base) ide_device_add(idx, &qd65xx_port_info); - outb(QD_DEF_CONTR, QD_CONTROL_PORT); - return 1; } else { ide_hwif_t *mate; @@ -487,8 +450,6 @@ static int __init qd_probe(int base) ide_device_add(idx, &qd65xx_port_info); - outb(QD_DEF_CONTR, QD_CONTROL_PORT); - return 0; /* no other qd65xx possible */ } } diff --git a/drivers/ide/pci/cmd640.c b/drivers/ide/pci/cmd640.c index bd24dad3cfc..ec667982809 100644 --- a/drivers/ide/pci/cmd640.c +++ b/drivers/ide/pci/cmd640.c @@ -787,7 +787,8 @@ static int __init cmd640x_init(void) /* * Try to enable the secondary interface, if not already enabled */ - if (cmd_hwif1->noprobe) { + if (cmd_hwif1->noprobe || + (cmd_hwif1->drives[0].noprobe && cmd_hwif1->drives[1].noprobe)) { port2 = "not probed"; } else { b = get_cmd640_reg(CNTRL); diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c index d0f7bb8b8ad..6357bb6269a 100644 --- a/drivers/ide/pci/hpt366.c +++ b/drivers/ide/pci/hpt366.c @@ -1570,10 +1570,12 @@ static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_devic if (rev < 3) info = &hpt36x; else { - static const struct hpt_info *hpt37x_info[] = - { &hpt370, &hpt370a, &hpt372, &hpt372n }; - - info = hpt37x_info[min_t(u8, rev, 6) - 3]; + switch (min_t(u8, rev, 6)) { + case 3: info = &hpt370; break; + case 4: info = &hpt370a; break; + case 5: info = &hpt372; break; + case 6: info = &hpt372n; break; + } idx++; } break; @@ -1626,7 +1628,7 @@ static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_devic return ide_setup_pci_device(dev, &d); } -static const struct pci_device_id hpt366_pci_tbl[] = { +static const struct pci_device_id hpt366_pci_tbl[] __devinitconst = { { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), 0 }, { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), 1 }, { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), 2 }, |