diff options
-rw-r--r-- | drivers/ide/Kconfig | 6 | ||||
-rw-r--r-- | drivers/ide/ide-io.c | 32 | ||||
-rw-r--r-- | drivers/ide/ide-iops.c | 11 | ||||
-rw-r--r-- | drivers/ide/ide.c | 37 | ||||
-rw-r--r-- | drivers/ide/pci/pdc202xx_new.c | 3 | ||||
-rw-r--r-- | include/linux/ide.h | 1 | ||||
-rw-r--r-- | kernel/time/clockevents.c | 69 |
7 files changed, 67 insertions, 92 deletions
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index 8f1fd017679..ca2e4f830c3 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -103,8 +103,10 @@ config BLK_DEV_IDE_SATA ---help--- There are two drivers for Serial ATA controllers. - The main driver, "libata", exists inside the SCSI subsystem - and supports most modern SATA controllers. + The main driver, "libata", uses the SCSI subsystem + and supports most modern SATA controllers. In order to use it + you may take a look at "Serial ATA (prod) and Parallel ATA + (experimental) drivers". The IDE driver (which you are currently configuring) supports a few first-generation SATA controllers. diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c index c193553f6fe..0e0280076fc 100644 --- a/drivers/ide/ide-io.c +++ b/drivers/ide/ide-io.c @@ -519,21 +519,24 @@ static ide_startstop_t ide_ata_error(ide_drive_t *drive, struct request *rq, u8 if ((stat & DRQ_STAT) && rq_data_dir(rq) == READ && hwif->err_stops_fifo == 0) try_to_flush_leftover_data(drive); + if (rq->errors >= ERROR_MAX || blk_noretry_request(rq)) { + ide_kill_rq(drive, rq); + return ide_stopped; + } + if (hwif->INB(IDE_STATUS_REG) & (BUSY_STAT|DRQ_STAT)) - /* force an abort */ - hwif->OUTB(WIN_IDLEIMMEDIATE, IDE_COMMAND_REG); + rq->errors |= ERROR_RESET; - if (rq->errors >= ERROR_MAX || blk_noretry_request(rq)) - ide_kill_rq(drive, rq); - else { - if ((rq->errors & ERROR_RESET) == ERROR_RESET) { - ++rq->errors; - return ide_do_reset(drive); - } - if ((rq->errors & ERROR_RECAL) == ERROR_RECAL) - drive->special.b.recalibrate = 1; + if ((rq->errors & ERROR_RESET) == ERROR_RESET) { ++rq->errors; + return ide_do_reset(drive); } + + if ((rq->errors & ERROR_RECAL) == ERROR_RECAL) + drive->special.b.recalibrate = 1; + + ++rq->errors; + return ide_stopped; } @@ -1025,6 +1028,13 @@ static ide_startstop_t start_request (ide_drive_t *drive, struct request *rq) if (!drive->special.all) { ide_driver_t *drv; + /* + * We reset the drive so we need to issue a SETFEATURES. + * Do it _after_ do_special() restored device parameters. + */ + if (drive->current_speed == 0xff) + ide_config_drive_speed(drive, drive->desired_speed); + if (rq->cmd_type == REQ_TYPE_ATA_CMD || rq->cmd_type == REQ_TYPE_ATA_TASK || rq->cmd_type == REQ_TYPE_ATA_TASKFILE) diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c index bd513f5a232..1ee53a551c3 100644 --- a/drivers/ide/ide-iops.c +++ b/drivers/ide/ide-iops.c @@ -583,8 +583,12 @@ u8 eighty_ninty_three (ide_drive_t *drive) if(!(drive->id->hw_config & 0x4000)) return 0; #endif /* CONFIG_IDEDMA_IVB */ - if (!(drive->id->hw_config & 0x2000)) - return 0; + /* + * FIXME: + * - change master/slave IDENTIFY order + * - force bit13 (80c cable present) check + * (unless the slave device is pre-ATA3) + */ return 1; } @@ -1090,6 +1094,9 @@ static void pre_reset(ide_drive_t *drive) if (HWIF(drive)->pre_reset != NULL) HWIF(drive)->pre_reset(drive); + if (drive->current_speed != 0xff) + drive->desired_speed = drive->current_speed; + drive->current_speed = 0xff; } /* diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c index 695610f0e3e..a6f098fda88 100644 --- a/drivers/ide/ide.c +++ b/drivers/ide/ide.c @@ -1124,17 +1124,40 @@ static int set_io_32bit(ide_drive_t *drive, int arg) static int set_using_dma (ide_drive_t *drive, int arg) { #ifdef CONFIG_BLK_DEV_IDEDMA + ide_hwif_t *hwif = drive->hwif; + int err = -EPERM; + if (!drive->id || !(drive->id->capability & 1)) - return -EPERM; - if (HWIF(drive)->ide_dma_check == NULL) - return -EPERM; + goto out; + + if (hwif->ide_dma_check == NULL) + goto out; + + err = -EBUSY; + if (ide_spin_wait_hwgroup(drive)) + goto out; + /* + * set ->busy flag, unlock and let it ride + */ + hwif->hwgroup->busy = 1; + spin_unlock_irq(&ide_lock); + + err = 0; + if (arg) { - if (ide_set_dma(drive)) - return -EIO; - if (HWIF(drive)->ide_dma_on(drive)) return -EIO; + if (ide_set_dma(drive) || hwif->ide_dma_on(drive)) + err = -EIO; } else ide_dma_off(drive); - return 0; + + /* + * lock, clear ->busy flag and unlock before leaving + */ + spin_lock_irq(&ide_lock); + hwif->hwgroup->busy = 0; + spin_unlock_irq(&ide_lock); +out: + return err; #else return -EPERM; #endif diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c index 6ceb25bc5a7..ace98929cc3 100644 --- a/drivers/ide/pci/pdc202xx_new.c +++ b/drivers/ide/pci/pdc202xx_new.c @@ -255,7 +255,7 @@ static int config_chipset_for_dma(ide_drive_t *drive) printk(KERN_WARNING "%s reduced to Ultra33 mode.\n", drive->name); } - if (drive->media != ide_disk) + if (drive->media != ide_disk && drive->media != ide_cdrom) return 0; if (id->capability & 4) { @@ -545,6 +545,7 @@ static void __devinit init_hwif_pdc202new(ide_hwif_t *hwif) hwif->drives[0].autotune = hwif->drives[1].autotune = 1; + hwif->atapi_dma = 1; hwif->ultra_mask = 0x7f; hwif->mwdma_mask = 0x07; diff --git a/include/linux/ide.h b/include/linux/ide.h index 34f2676b3c6..58564a19986 100644 --- a/include/linux/ide.h +++ b/include/linux/ide.h @@ -615,6 +615,7 @@ typedef struct ide_drive_s { u8 init_speed; /* transfer rate set at boot */ u8 pio_speed; /* unused by core, used by some drivers for fallback from DMA */ u8 current_speed; /* current transfer rate set */ + u8 desired_speed; /* desired transfer rate set */ u8 dn; /* now wide spread use */ u8 wcache; /* status of write cache */ u8 acoustic; /* acoustic management */ diff --git a/kernel/time/clockevents.c b/kernel/time/clockevents.c index 67932ea78c1..76212b2a99d 100644 --- a/kernel/time/clockevents.c +++ b/kernel/time/clockevents.c @@ -274,72 +274,3 @@ void clockevents_notify(unsigned long reason, void *arg) } EXPORT_SYMBOL_GPL(clockevents_notify); -#ifdef CONFIG_SYSFS - -/** - * clockevents_show_registered - sysfs interface for listing clockevents - * @dev: unused - * @buf: char buffer to be filled with clock events list - * - * Provides sysfs interface for listing registered clock event devices - */ -static ssize_t clockevents_show_registered(struct sys_device *dev, char *buf) -{ - struct list_head *tmp; - char *p = buf; - int cpu; - - spin_lock(&clockevents_lock); - - list_for_each(tmp, &clockevent_devices) { - struct clock_event_device *ce; - - ce = list_entry(tmp, struct clock_event_device, list); - p += sprintf(p, "%-20s F:%04x M:%d", ce->name, - ce->features, ce->mode); - p += sprintf(p, " C:"); - if (!cpus_equal(ce->cpumask, cpu_possible_map)) { - for_each_cpu_mask(cpu, ce->cpumask) - p += sprintf(p, " %d", cpu); - } else { - /* - * FIXME: Add the cpu which is handling this sucker - */ - } - p += sprintf(p, "\n"); - } - - spin_unlock(&clockevents_lock); - - return p - buf; -} - -/* - * Sysfs setup bits: - */ -static SYSDEV_ATTR(registered, 0600, - clockevents_show_registered, NULL); - -static struct sysdev_class clockevents_sysclass = { - set_kset_name("clockevents"), -}; - -static struct sys_device clockevents_sys_device = { - .id = 0, - .cls = &clockevents_sysclass, -}; - -static int __init clockevents_sysfs_init(void) -{ - int error = sysdev_class_register(&clockevents_sysclass); - - if (!error) - error = sysdev_register(&clockevents_sys_device); - if (!error) - error = sysdev_create_file( - &clockevents_sys_device, - &attr_registered); - return error; -} -device_initcall(clockevents_sysfs_init); -#endif |