diff options
98 files changed, 9948 insertions, 671 deletions
diff --git a/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen new file mode 100644 index 00000000000..1e6a23fdf2f --- /dev/null +++ b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen @@ -0,0 +1,61 @@ +README on the ADC/Touchscreen Controller +======================================== + +The LH79524 and LH7A404 include a built-in Analog to Digital +controller (ADC) that is used to process input from a touchscreen. +The driver only implements a four-wire touch panel protocol. + +The touchscreen driver is maintenance free except for the pen-down or +touch threshold. Some resistive displays and board combinations may +require tuning of this threshold. The driver exposes some of it's +internal state in the sys filesystem. If the kernel is configured +with it, CONFIG_SYSFS, and sysfs is mounted at /sys, there will be a +directory + + /sys/devices/platform/adc-lh7.0 + +containing these files. + + -r--r--r-- 1 root root 4096 Jan 1 00:00 samples + -rw-r--r-- 1 root root 4096 Jan 1 00:00 threshold + -r--r--r-- 1 root root 4096 Jan 1 00:00 threshold_range + +The threshold is the current touch threshold. It defaults to 750 on +most targets. + + # cat threshold + 750 + +The threshold_range contains the range of valid values for the +threshold. Values outside of this range will be silently ignored. + + # cat threshold_range + 0 1023 + +To change the threshold, write a value to the threshold file. + + # echo 500 > threshold + # cat threshold + 500 + +The samples file contains the most recently sampled values from the +ADC. There are 12. Below are typical of the last sampled values when +the pen has been released. The first two and last two samples are for +detecting whether or not the pen is down. The third through sixth are +X coordinate samples. The seventh through tenth are Y coordinate +samples. + + # cat samples + 1023 1023 0 0 0 0 530 529 530 529 1023 1023 + +To determine a reasonable threshold, press on the touch panel with an +appropriate stylus and read the values from samples. + + # cat samples + 1023 676 92 103 101 102 855 919 922 922 1023 679 + +The first and eleventh samples are discarded. Thus, the important +values are the second and twelfth which are used to determine if the +pen is down. When both are below the threshold, the driver registers +that the pen is down. When either is above the threshold, it +registers then pen is up. diff --git a/Documentation/arm/Sharp-LH/LCDPanels b/Documentation/arm/Sharp-LH/LCDPanels new file mode 100644 index 00000000000..fb1b21c2f2f --- /dev/null +++ b/Documentation/arm/Sharp-LH/LCDPanels @@ -0,0 +1,59 @@ +README on the LCD Panels +======================== + +Configuration options for several LCD panels, available from Logic PD, +are included in the kernel source. This README will help you +understand the configuration data and give you some guidance for +adding support for other panels if you wish. + + +lcd-panels.h +------------ + +There is no way, at present, to detect which panel is attached to the +system at runtime. Thus the kernel configuration is static. The file +arch/arm/mach-ld7a40x/lcd-panels.h (or similar) defines all of the +panel specific parameters. + +It should be possible for this data to be shared among several device +families. The current layout may be insufficiently general, but it is +amenable to improvement. + + +PIXEL_CLOCK +----------- + +The panel data sheets will give a range of acceptable pixel clocks. +The fundamental LCDCLK input frequency is divided down by a PCD +constant in field '.tim2'. It may happen that it is impossible to set +the pixel clock within this range. A clock which is too slow will +tend to flicker. For the highest quality image, set the clock as high +as possible. + + +MARGINS +------- + +These values may be difficult to glean from the panel data sheet. In +the case of the Sharp panels, the upper margin is explicitly called +out as a specific number of lines from the top of the frame. The +other values may not matter as much as the panels tend to +automatically center the image. + + +Sync Sense +---------- + +The sense of the hsync and vsync pulses may be called out in the data +sheet. On one panel, the sense of these pulses determine the height +of the visible region on the panel. Most of the Sharp panels use +negative sense sync pulses set by the TIM2_IHS and TIM2_IVS bits in +'.tim2'. + + +Pel Layout +---------- + +The Sharp color TFT panels are all configured for 16 bit direct color +modes. The amba-lcd driver sets the pel mode to 565 for 5 bits of +each red and blue and 6 bits of green. diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 08b7cc900ca..f47cf9af3bc 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -270,6 +270,11 @@ config ARCH_AT91RM9200 Say Y here if you intend to run this kernel on an Atmel AT91RM9200-based board. +config ARCH_PNX4008 + bool "Philips Nexperia PNX4008 Mobile" + help + This enables support for Philips PNX4008 mobile platform. + endchoice source "arch/arm/mach-clps711x/Kconfig" diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 6f8e84c1c1f..6c97aa70d3b 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -116,6 +116,7 @@ endif machine-$(CONFIG_ARCH_REALVIEW) := realview machine-$(CONFIG_ARCH_AT91RM9200) := at91rm9200 machine-$(CONFIG_ARCH_EP93XX) := ep93xx + machine-$(CONFIG_ARCH_PNX4008) := pnx4008 ifeq ($(CONFIG_ARCH_EBSA110),y) # This is what happens if you forget the IOCS16 line. diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index b56f5e691d6..23016f6aa64 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -605,8 +605,8 @@ proc_types: b __armv4_mmu_cache_off b __armv4_mmu_cache_flush - .word 0x00070000 @ ARMv6 - .word 0x000f0000 + .word 0x0007b000 @ ARMv6 + .word 0x0007f000 b __armv4_mmu_cache_on b __armv4_mmu_cache_off b __armv6_mmu_cache_flush diff --git a/arch/arm/configs/lpd7a400_defconfig b/arch/arm/configs/lpd7a400_defconfig index 67eaa26c264..bf9cf9c6d2d 100644 --- a/arch/arm/configs/lpd7a400_defconfig +++ b/arch/arm/configs/lpd7a400_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.12-rc1-bk2 -# Mon Mar 28 00:06:33 2005 +# Linux kernel version: 2.6.12 +# Thu Nov 3 14:15:32 2005 # CONFIG_ARM=y CONFIG_MMU=y @@ -17,6 +17,7 @@ CONFIG_EXPERIMENTAL=y CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup @@ -36,6 +37,8 @@ CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_PRINTK=y +CONFIG_BUG=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y # CONFIG_EPOLL is not set @@ -71,6 +74,7 @@ CONFIG_BASE_SMALL=0 # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7952X is not set CONFIG_ARCH_LH7A40X=y # CONFIG_ARCH_OMAP is not set # CONFIG_ARCH_VERSATILE is not set @@ -84,6 +88,7 @@ CONFIG_ARCH_LH7A40X=y CONFIG_MACH_LPD7A400=y # CONFIG_MACH_LPD7A404 is not set CONFIG_ARCH_LH7A400=y +CONFIG_LPD7A40X_CPLD_SSP=y # CONFIG_LH7A40X_CONTIGMEM is not set # CONFIG_LH7A40X_ONE_BANK_PER_NODE is not set @@ -110,6 +115,8 @@ CONFIG_ARM_THUMB=y # # Bus support # +CONFIG_ARM_AMBA=y +CONFIG_ISA_DMA_API=y # # PCCARD (PCMCIA/CardBus) support @@ -119,6 +126,7 @@ CONFIG_ARM_THUMB=y # # Kernel Features # +# CONFIG_SMP is not set CONFIG_PREEMPT=y CONFIG_DISCONTIGMEM=y CONFIG_ALIGNMENT_TRAP=y @@ -175,7 +183,7 @@ CONFIG_MTD=y # CONFIG_MTD_CONCAT is not set CONFIG_MTD_PARTITIONS=y # CONFIG_MTD_REDBOOT_PARTS is not set -# CONFIG_MTD_CMDLINE_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y # CONFIG_MTD_AFS_PARTS is not set # @@ -217,7 +225,10 @@ CONFIG_MTD_CFI_UTIL=y # Mapping drivers for chip access # # CONFIG_MTD_COMPLEX_MAPPINGS is not set -# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x00000000 +CONFIG_MTD_PHYSMAP_LEN=0x04000000 +CONFIG_MTD_PHYSMAP_BANKWIDTH=4 # CONFIG_MTD_ARM_INTEGRATOR is not set # CONFIG_MTD_EDB7312 is not set @@ -254,7 +265,6 @@ CONFIG_MTD_CFI_UTIL=y # # Block devices # -# CONFIG_BLK_DEV_FD is not set # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set @@ -288,13 +298,15 @@ CONFIG_BLK_DEV_IDEDISK=y # CONFIG_BLK_DEV_IDECD is not set # CONFIG_BLK_DEV_IDETAPE is not set # CONFIG_BLK_DEV_IDEFLOPPY is not set +# CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set +CONFIG_IDE_POLL=y # # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y -# CONFIG_IDE_ARM is not set +CONFIG_IDE_ARM=y # CONFIG_BLK_DEV_IDEDMA is not set # CONFIG_IDEDMA_AUTO is not set # CONFIG_BLK_DEV_HD is not set @@ -302,7 +314,37 @@ CONFIG_IDE_GENERIC=y # # SCSI device support # -# CONFIG_SCSI is not set +CONFIG_SCSI=y +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +# CONFIG_BLK_DEV_SD is not set +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set + +# +# SCSI Transport Attributes +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set + +# +# SCSI low-level drivers +# +# CONFIG_SCSI_SATA is not set +# CONFIG_SCSI_DEBUG is not set # # Multi-device support (RAID and LVM) @@ -331,7 +373,6 @@ CONFIG_NET=y # CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set -# CONFIG_NETLINK_DEV is not set CONFIG_UNIX=y # CONFIG_NET_KEY is not set CONFIG_INET=y @@ -438,13 +479,10 @@ CONFIG_INPUT=y # # Userland interfaces # -CONFIG_INPUT_MOUSEDEV=y -CONFIG_INPUT_MOUSEDEV_PSAUX=y -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set # CONFIG_INPUT_TSDEV is not set -# CONFIG_INPUT_EVDEV is not set +CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # @@ -453,7 +491,13 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_KEYBOARD is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TOUCHSCREEN is not set +CONFIG_INPUT_TOUCHSCREEN=y +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +CONFIG_TOUCHSCREEN_ADS7843_LH7=y +CONFIG_HAS_TOUCHSCREEN_ADS7843_LH7=y # CONFIG_INPUT_MISC is not set # @@ -461,7 +505,6 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # # CONFIG_SERIO is not set # CONFIG_GAMEPORT is not set -CONFIG_SOUND_GAMEPORT=y # # Character devices @@ -479,6 +522,8 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +# CONFIG_SERIAL_AMBA_PL010 is not set +# CONFIG_SERIAL_AMBA_PL011 is not set CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_SERIAL_LH7A40X=y @@ -510,7 +555,6 @@ CONFIG_RTC=y # # TPM devices # -# CONFIG_TCG_TPM is not set # # I2C support @@ -534,18 +578,73 @@ CONFIG_RTC=y # # Graphics support # -# CONFIG_FB is not set +CONFIG_FB=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +CONFIG_FB_SOFT_CURSOR=y +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set +CONFIG_FB_ARMCLCD=y +CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT=y +# CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02 is not set +# CONFIG_FB_ARMCLCD_SHARP_LQ64D343 is not set +# CONFIG_FB_ARMCLCD_SHARP_LQ10D368 is not set +# CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41 is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_VIRTUAL is not set # # Console display driver support # # CONFIG_VGA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE is not set + +# +# Logo configuration +# +# CONFIG_LOGO is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Sound # -# CONFIG_SOUND is not set +CONFIG_SOUND=y + +# +# Advanced Linux Sound Architecture +# +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +# CONFIG_SND_RTCTIMER is not set +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set + +# +# Generic devices +# +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_AC97_CODEC=y + +# +# ALSA ARM devices +# +CONFIG_SND_LH7A40X_AC97=y + +# +# Open Sound System +# +# CONFIG_SOUND_PRIME is not set # # USB support diff --git a/arch/arm/configs/lpd7a404_defconfig b/arch/arm/configs/lpd7a404_defconfig index 208d591ebfc..3a57be32e84 100644 --- a/arch/arm/configs/lpd7a404_defconfig +++ b/arch/arm/configs/lpd7a404_defconfig @@ -1,52 +1,58 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.12-rc1-bk2 -# Mon Mar 28 00:14:08 2005 +# Linux kernel version: 2.6.16 +# Thu Mar 23 17:50:31 2006 # CONFIG_ARM=y CONFIG_MMU=y -CONFIG_UID16=y CONFIG_RWSEM_GENERIC_SPINLOCK=y CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_IOMAP=y # # Code maturity level options # CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup # CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y # CONFIG_SWAP is not set CONFIG_SYSVIPC=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y # CONFIG_AUDIT is not set -# CONFIG_HOTPLUG is not set -CONFIG_KOBJECT_UEVENT=y CONFIG_IKCONFIG=y # CONFIG_IKCONFIG_PROC is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_UID16=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set +# CONFIG_HOTPLUG is not set +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y # CONFIG_EPOLL is not set -CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SHMEM=y CONFIG_CC_ALIGN_FUNCTIONS=0 CONFIG_CC_ALIGN_LABELS=0 CONFIG_CC_ALIGN_LOOPS=0 CONFIG_CC_ALIGN_JUMPS=0 +CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set +CONFIG_OBSOLETE_INTERMODULE=y # # Loadable module support @@ -54,6 +60,23 @@ CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set # +# Block layer +# + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +# CONFIG_IOSCHED_AS is not set +# CONFIG_IOSCHED_DEADLINE is not set +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" + +# # System Type # # CONFIG_ARCH_CLPS7500 is not set @@ -71,11 +94,15 @@ CONFIG_BASE_SMALL=0 # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7952X is not set CONFIG_ARCH_LH7A40X=y # CONFIG_ARCH_OMAP is not set # CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set # CONFIG_ARCH_IMX is not set # CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_AT91RM9200 is not set # # LH7A40X Implementations @@ -110,6 +137,7 @@ CONFIG_ARM_THUMB=y # # Bus support # +CONFIG_ARM_AMBA=y # # PCCARD (PCMCIA/CardBus) support @@ -120,7 +148,18 @@ CONFIG_ARM_THUMB=y # Kernel Features # CONFIG_PREEMPT=y +# CONFIG_NO_IDLE_HZ is not set +# CONFIG_AEABI is not set +CONFIG_ARCH_DISCONTIGMEM_ENABLE=y +CONFIG_SELECT_MEMORY_MODEL=y +# CONFIG_FLATMEM_MANUAL is not set +CONFIG_DISCONTIGMEM_MANUAL=y +# CONFIG_SPARSEMEM_MANUAL is not set CONFIG_DISCONTIGMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_NEED_MULTIPLE_NODES=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 CONFIG_ALIGNMENT_TRAP=y # @@ -154,6 +193,84 @@ CONFIG_BINFMT_ELF=y # Power management options # # CONFIG_PM is not set +# CONFIG_APM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set # # Device Drivers @@ -168,6 +285,11 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_DEBUG_DRIVER is not set # +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# # Memory Technology Devices (MTD) # CONFIG_MTD=y @@ -175,7 +297,7 @@ CONFIG_MTD=y # CONFIG_MTD_CONCAT is not set CONFIG_MTD_PARTITIONS=y # CONFIG_MTD_REDBOOT_PARTS is not set -# CONFIG_MTD_CMDLINE_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y # CONFIG_MTD_AFS_PARTS is not set # @@ -186,6 +308,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_FTL is not set # CONFIG_NFTL is not set # CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set # # RAM/ROM/Flash chip drivers @@ -211,15 +334,18 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_RAM is not set # CONFIG_MTD_ROM is not set # CONFIG_MTD_ABSENT is not set -# CONFIG_MTD_XIP is not set +# CONFIG_MTD_OBSOLETE_CHIPS is not set # # Mapping drivers for chip access # # CONFIG_MTD_COMPLEX_MAPPINGS is not set -# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x00000000 +CONFIG_MTD_PHYSMAP_LEN=0x04000000 +CONFIG_MTD_PHYSMAP_BANKWIDTH=4 # CONFIG_MTD_ARM_INTEGRATOR is not set -# CONFIG_MTD_EDB7312 is not set +# CONFIG_MTD_PLATRAM is not set # # Self-contained MTD device drivers @@ -243,6 +369,11 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_NAND is not set # +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# # Parallel port support # # CONFIG_PARPORT is not set @@ -254,7 +385,6 @@ CONFIG_MTD_CFI_UTIL=y # # Block devices # -# CONFIG_BLK_DEV_FD is not set # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set @@ -262,16 +392,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_UB is not set # CONFIG_BLK_DEV_RAM is not set CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_INITRAMFS_SOURCE="" # CONFIG_CDROM_PKTCDVD is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -# CONFIG_IOSCHED_AS is not set -# CONFIG_IOSCHED_DEADLINE is not set -CONFIG_IOSCHED_CFQ=y # CONFIG_ATA_OVER_ETH is not set # @@ -291,12 +412,13 @@ CONFIG_BLK_DEV_IDEDISK=y # CONFIG_BLK_DEV_IDEFLOPPY is not set # CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set +CONFIG_IDE_POLL=y # # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y -# CONFIG_IDE_ARM is not set +CONFIG_IDE_ARM=y # CONFIG_BLK_DEV_IDEDMA is not set # CONFIG_IDEDMA_AUTO is not set # CONFIG_BLK_DEV_HD is not set @@ -304,6 +426,7 @@ CONFIG_IDE_GENERIC=y # # SCSI device support # +# CONFIG_RAID_ATTRS is not set CONFIG_SCSI=y # CONFIG_SCSI_PROC_FS is not set @@ -315,6 +438,7 @@ CONFIG_SCSI=y # CONFIG_CHR_DEV_OSST is not set # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs @@ -329,10 +453,12 @@ CONFIG_SCSI=y # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set # # SCSI low-level drivers # +# CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_SATA is not set # CONFIG_SCSI_DEBUG is not set @@ -344,6 +470,7 @@ CONFIG_SCSI=y # # Fusion MPT device support # +# CONFIG_FUSION is not set # # IEEE 1394 (FireWire) support @@ -354,70 +481,8 @@ CONFIG_SCSI=y # # -# Networking support +# Network device support # -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -# CONFIG_PACKET_MMAP is not set -# CONFIG_NETLINK_DEV is not set -CONFIG_UNIX=y -# CONFIG_NET_KEY is not set -CONFIG_INET=y -# CONFIG_IP_MULTICAST is not set -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -CONFIG_IP_PNP_BOOTP=y -CONFIG_IP_PNP_RARP=y -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_TUNNEL is not set -# CONFIG_IP_TCPDIAG is not set -# CONFIG_IP_TCPDIAG_IPV6 is not set -# CONFIG_IPV6 is not set -# CONFIG_NETFILTER is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_SCTP is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_NET_DIVERT is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# -# CONFIG_NET_SCHED is not set -# CONFIG_NET_CLS_ROUTE is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set -# CONFIG_HAMRADIO is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set @@ -425,11 +490,17 @@ CONFIG_NETDEVICES=y # CONFIG_TUN is not set # +# PHY device support +# +# CONFIG_PHYLIB is not set + +# # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y CONFIG_MII=y CONFIG_SMC91X=y +# CONFIG_DM9000 is not set # # Ethernet (1000 Mbit) @@ -456,6 +527,8 @@ CONFIG_SMC91X=y # CONFIG_SLIP is not set # CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set # # ISDN subsystem @@ -470,10 +543,13 @@ CONFIG_INPUT=y # # Userland interfaces # -# CONFIG_INPUT_MOUSEDEV is not set +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set # CONFIG_INPUT_TSDEV is not set -# CONFIG_INPUT_EVDEV is not set +CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # @@ -482,7 +558,13 @@ CONFIG_INPUT=y # CONFIG_INPUT_KEYBOARD is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TOUCHSCREEN is not set +CONFIG_INPUT_TOUCHSCREEN=y +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +CONFIG_TOUCHSCREEN_ADC_LH7=y +CONFIG_HAS_TOUCHSCREEN_ADC_LH7=y # CONFIG_INPUT_MISC is not set # @@ -490,7 +572,6 @@ CONFIG_INPUT=y # # CONFIG_SERIO is not set # CONFIG_GAMEPORT is not set -CONFIG_SOUND_GAMEPORT=y # # Character devices @@ -508,6 +589,8 @@ CONFIG_HW_CONSOLE=y # # Non-8250 serial port support # +# CONFIG_SERIAL_AMBA_PL010 is not set +# CONFIG_SERIAL_AMBA_PL011 is not set CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_SERIAL_LH7A40X=y @@ -533,13 +616,13 @@ CONFIG_RTC=y # # Ftape, the floppy tape device driver # -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # # TPM devices # # CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set # # I2C support @@ -547,10 +630,33 @@ CONFIG_RTC=y # CONFIG_I2C is not set # +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# # Misc devices # # +# Multimedia Capabilities Port drivers +# + +# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -563,18 +669,83 @@ CONFIG_RTC=y # # Graphics support # -# CONFIG_FB is not set +CONFIG_FB=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set +CONFIG_FB_ARMCLCD=y +CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT=y +# CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02 is not set +# CONFIG_FB_ARMCLCD_SHARP_LQ64D343 is not set +# CONFIG_FB_ARMCLCD_SHARP_LQ10D368 is not set +# CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41 is not set +# CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE is not set +# CONFIG_FB_ARMCLCD_HITACHI is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_VIRTUAL is not set # # Console display driver support # # CONFIG_VGA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE is not set + +# +# Logo configuration +# +# CONFIG_LOGO is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Sound # -# CONFIG_SOUND is not set +CONFIG_SOUND=y + +# +# Advanced Linux Sound Architecture +# +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +# CONFIG_SND_RTCTIMER is not set +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set + +# +# Generic devices +# +CONFIG_SND_AC97_CODEC=y +CONFIG_SND_AC97_BUS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set + +# +# ALSA ARM devices +# +# CONFIG_SND_ARMAACI is not set +CONFIG_SND_LH7A40X_AC97=y + +# +# USB devices +# +# CONFIG_SND_USB_AUDIO is not set + +# +# Open Sound System +# +# CONFIG_SOUND_PRIME is not set # # USB support @@ -595,6 +766,7 @@ CONFIG_USB_DEVICEFS=y # # USB Host Controller Drivers # +# CONFIG_USB_ISP116X_HCD is not set CONFIG_USB_OHCI_HCD=y # CONFIG_USB_OHCI_BIG_ENDIAN is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y @@ -603,16 +775,19 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # # USB Device Class drivers # -# CONFIG_USB_BLUETOOTH_TTY is not set +# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set # -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=y CONFIG_USB_STORAGE_DEBUG=y -# CONFIG_USB_STORAGE_RW_DETECT is not set CONFIG_USB_STORAGE_DATAFAB=y # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set @@ -621,22 +796,32 @@ CONFIG_USB_STORAGE_DATAFAB=y # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_LIBUSUAL is not set # # USB Input Devices # CONFIG_USB_HID=y CONFIG_USB_HIDINPUT=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set # CONFIG_HID_FF is not set # CONFIG_USB_HIDDEV is not set # CONFIG_USB_AIPTEK is not set # CONFIG_USB_WACOM is not set +# CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set # CONFIG_USB_MTOUCH is not set +# CONFIG_USB_ITMTOUCH is not set # CONFIG_USB_EGALAX is not set +# CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set +# CONFIG_USB_ATI_REMOTE2 is not set +# CONFIG_USB_KEYSPAN_REMOTE is not set +# CONFIG_USB_APPLETOUCH is not set # # USB Imaging devices @@ -686,16 +871,33 @@ CONFIG_USB_MON=y # CONFIG_USB_PHIDGETKIT is not set # CONFIG_USB_PHIDGETSERVO is not set # CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_LD is not set # CONFIG_USB_TEST is not set # -# USB ATM/DSL drivers +# USB DSL modem support # # # USB Gadget Support # -# CONFIG_USB_GADGET is not set +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +CONFIG_USB_GADGET_LH7=y +CONFIG_USB_LH7=y +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +CONFIG_USB_ZERO=y +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set # # MMC/SD Card support @@ -707,6 +909,7 @@ CONFIG_USB_MON=y # CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set @@ -716,17 +919,17 @@ CONFIG_JBD=y CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set - -# -# XFS support -# +# CONFIG_FS_POSIX_ACL is not set # CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set # # CD-ROM/DVD Filesystems @@ -749,12 +952,11 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" # CONFIG_PROC_FS=y CONFIG_SYSFS=y -# CONFIG_DEVFS_FS is not set -# CONFIG_DEVPTS_FS_XATTR is not set CONFIG_TMPFS=y -# CONFIG_TMPFS_XATTR is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set +# CONFIG_CONFIGFS_FS is not set # # Miscellaneous filesystems @@ -769,8 +971,8 @@ CONFIG_RAMFS=y # CONFIG_JFFS_FS is not set CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 -# CONFIG_JFFS2_FS_NAND is not set -# CONFIG_JFFS2_FS_NOR_ECC is not set +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_SUMMARY is not set # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set CONFIG_JFFS2_ZLIB=y CONFIG_JFFS2_RTIME=y @@ -787,12 +989,14 @@ CONFIG_CRAMFS=y # CONFIG_NFS_FS=y CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set # CONFIG_NFS_DIRECTIO is not set # CONFIG_NFSD is not set CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set @@ -801,6 +1005,7 @@ CONFIG_SUNRPC=y # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set # # Partition Types @@ -820,6 +1025,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_SGI_PARTITION is not set # CONFIG_ULTRIX_PARTITION is not set # CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # @@ -875,19 +1081,24 @@ CONFIG_NLS_DEFAULT="iso8859-1" # Kernel hacking # # CONFIG_PRINTK_TIME is not set -CONFIG_DEBUG_KERNEL=y CONFIG_MAGIC_SYSRQ=y -CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=16 +CONFIG_DETECT_SOFTLOCKUP=y # CONFIG_SCHEDSTATS is not set # CONFIG_DEBUG_SLAB is not set CONFIG_DEBUG_PREEMPT=y +CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set CONFIG_FRAME_POINTER=y +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set CONFIG_DEBUG_USER=y # CONFIG_DEBUG_WAITQ is not set CONFIG_DEBUG_ERRORS=y @@ -912,6 +1123,7 @@ CONFIG_DEBUG_ERRORS=y # Library routines # # CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y diff --git a/arch/arm/configs/pnx4008_defconfig b/arch/arm/configs/pnx4008_defconfig new file mode 100644 index 00000000000..8a078d479d5 --- /dev/null +++ b/arch/arm/configs/pnx4008_defconfig @@ -0,0 +1,2072 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.17-rc1 +# Thu Apr 6 17:05:58 2006 +# +CONFIG_ARM=y +CONFIG_MMU=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_VECTORS_BASE=0xffff0000 + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_POSIX_MQUEUE=y +CONFIG_BSD_PROCESS_ACCT=y +# CONFIG_BSD_PROCESS_ACCT_V3 is not set +CONFIG_SYSCTL=y +CONFIG_AUDIT=y +# CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_UID16=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_EMBEDDED=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_SLAB=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set +CONFIG_OBSOLETE_INTERMODULE=m + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_KMOD=y + +# +# Block layer +# +# CONFIG_BLK_DEV_IO_TRACE is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_IOP3XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_AT91RM9200 is not set +CONFIG_ARCH_PNX4008=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set + +# +# Bus support +# + +# +# PCCARD (PCMCIA/CardBus) support +# +CONFIG_PCCARD=m +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=m +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y + +# +# PC-card bridges +# + +# +# Kernel Features +# +CONFIG_PREEMPT=y +# CONFIG_NO_IDLE_HZ is not set +CONFIG_HZ=100 +# CONFIG_AEABI is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0 +CONFIG_ZBOOT_ROM_BSS=0 +CONFIG_CMDLINE="mem=64M console=ttyS0,115200" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +# CONFIG_FPE_NWFPE is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +CONFIG_BINFMT_AOUT=m +CONFIG_BINFMT_MISC=m +# CONFIG_ARTHUR is not set + +# +# Power management options +# +CONFIG_PM=y +CONFIG_PM_LEGACY=y +# CONFIG_PM_DEBUG is not set +CONFIG_APM=m + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +CONFIG_PACKET=m +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=m +CONFIG_XFRM=y +CONFIG_XFRM_USER=m +CONFIG_NET_KEY=m +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_MULTIPLE_TABLES=y +CONFIG_IP_ROUTE_FWMARK=y +CONFIG_IP_ROUTE_MULTIPATH=y +# CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set +CONFIG_IP_ROUTE_VERBOSE=y +# CONFIG_IP_PNP is not set +CONFIG_NET_IPIP=m +CONFIG_NET_IPGRE=m +CONFIG_NET_IPGRE_BROADCAST=y +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +CONFIG_INET_AH=m +CONFIG_INET_ESP=m +CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_TUNNEL=m +CONFIG_INET_TUNNEL=m +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y + +# +# IP: Virtual Server Configuration +# +CONFIG_IP_VS=m +# CONFIG_IP_VS_DEBUG is not set +CONFIG_IP_VS_TAB_BITS=12 + +# +# IPVS transport protocol load balancing support +# +CONFIG_IP_VS_PROTO_TCP=y +CONFIG_IP_VS_PROTO_UDP=y +CONFIG_IP_VS_PROTO_ESP=y +CONFIG_IP_VS_PROTO_AH=y + +# +# IPVS scheduler +# +CONFIG_IP_VS_RR=m +CONFIG_IP_VS_WRR=m +CONFIG_IP_VS_LC=m +CONFIG_IP_VS_WLC=m +CONFIG_IP_VS_LBLC=m +CONFIG_IP_VS_LBLCR=m +CONFIG_IP_VS_DH=m +CONFIG_IP_VS_SH=m +CONFIG_IP_VS_SED=m +CONFIG_IP_VS_NQ=m + +# +# IPVS application helper +# +CONFIG_IP_VS_FTP=m +CONFIG_IPV6=m +CONFIG_IPV6_PRIVACY=y +# CONFIG_IPV6_ROUTER_PREF is not set +CONFIG_INET6_AH=m +CONFIG_INET6_ESP=m +CONFIG_INET6_IPCOMP=m +CONFIG_INET6_XFRM_TUNNEL=m +CONFIG_INET6_TUNNEL=m +CONFIG_IPV6_TUNNEL=m +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set +CONFIG_BRIDGE_NETFILTER=y + +# +# Core Netfilter Configuration +# +# CONFIG_NETFILTER_NETLINK is not set +# CONFIG_NETFILTER_XTABLES is not set + +# +# IP: Netfilter Configuration +# +CONFIG_IP_NF_CONNTRACK=m +CONFIG_IP_NF_CT_ACCT=y +CONFIG_IP_NF_CONNTRACK_MARK=y +# CONFIG_IP_NF_CONNTRACK_EVENTS is not set +CONFIG_IP_NF_CT_PROTO_SCTP=m +CONFIG_IP_NF_FTP=m +CONFIG_IP_NF_IRC=m +# CONFIG_IP_NF_NETBIOS_NS is not set +CONFIG_IP_NF_TFTP=m +CONFIG_IP_NF_AMANDA=m +# CONFIG_IP_NF_PPTP is not set +# CONFIG_IP_NF_H323 is not set +CONFIG_IP_NF_QUEUE=m + +# +# IPv6: Netfilter Configuration (EXPERIMENTAL) +# +CONFIG_IP6_NF_QUEUE=m + +# +# DECnet: Netfilter Configuration +# +CONFIG_DECNET_NF_GRABULATOR=m + +# +# Bridge: Netfilter Configuration +# +CONFIG_BRIDGE_NF_EBTABLES=m +CONFIG_BRIDGE_EBT_BROUTE=m +CONFIG_BRIDGE_EBT_T_FILTER=m +CONFIG_BRIDGE_EBT_T_NAT=m +CONFIG_BRIDGE_EBT_802_3=m +CONFIG_BRIDGE_EBT_AMONG=m +CONFIG_BRIDGE_EBT_ARP=m +CONFIG_BRIDGE_EBT_IP=m +CONFIG_BRIDGE_EBT_LIMIT=m +CONFIG_BRIDGE_EBT_MARK=m +CONFIG_BRIDGE_EBT_PKTTYPE=m +CONFIG_BRIDGE_EBT_STP=m +CONFIG_BRIDGE_EBT_VLAN=m +CONFIG_BRIDGE_EBT_ARPREPLY=m +CONFIG_BRIDGE_EBT_DNAT=m +CONFIG_BRIDGE_EBT_MARK_T=m +CONFIG_BRIDGE_EBT_REDIRECT=m +CONFIG_BRIDGE_EBT_SNAT=m +CONFIG_BRIDGE_EBT_LOG=m +# CONFIG_BRIDGE_EBT_ULOG is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +CONFIG_IP_SCTP=m +# CONFIG_SCTP_DBG_MSG is not set +# CONFIG_SCTP_DBG_OBJCNT is not set +# CONFIG_SCTP_HMAC_NONE is not set +# CONFIG_SCTP_HMAC_SHA1 is not set +CONFIG_SCTP_HMAC_MD5=y + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +CONFIG_ATM=y +CONFIG_ATM_CLIP=y +# CONFIG_ATM_CLIP_NO_ICMP is not set +CONFIG_ATM_LANE=m +CONFIG_ATM_MPOA=m +CONFIG_ATM_BR2684=m +# CONFIG_ATM_BR2684_IPFILTER is not set +CONFIG_BRIDGE=m +CONFIG_VLAN_8021Q=m +CONFIG_DECNET=m +# CONFIG_DECNET_ROUTER is not set +CONFIG_LLC=m +CONFIG_LLC2=m +CONFIG_IPX=m +# CONFIG_IPX_INTERN is not set +CONFIG_ATALK=m +CONFIG_DEV_APPLETALK=y +CONFIG_IPDDP=m +CONFIG_IPDDP_ENCAP=y +CONFIG_IPDDP_DECAP=y +CONFIG_X25=m +CONFIG_LAPB=m +# CONFIG_NET_DIVERT is not set +CONFIG_ECONET=m +CONFIG_ECONET_AUNUDP=y +CONFIG_ECONET_NATIVE=y +CONFIG_WAN_ROUTER=m + +# +# QoS and/or fair queueing +# +CONFIG_NET_SCHED=y +CONFIG_NET_SCH_CLK_JIFFIES=y +# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set +# CONFIG_NET_SCH_CLK_CPU is not set + +# +# Queueing/Scheduling +# +CONFIG_NET_SCH_CBQ=m +CONFIG_NET_SCH_HTB=m +CONFIG_NET_SCH_HFSC=m +CONFIG_NET_SCH_ATM=m +CONFIG_NET_SCH_PRIO=m +CONFIG_NET_SCH_RED=m +CONFIG_NET_SCH_SFQ=m +CONFIG_NET_SCH_TEQL=m +CONFIG_NET_SCH_TBF=m +CONFIG_NET_SCH_GRED=m +CONFIG_NET_SCH_DSMARK=m +CONFIG_NET_SCH_NETEM=m +CONFIG_NET_SCH_INGRESS=m + +# +# Classification +# +CONFIG_NET_CLS=y +# CONFIG_NET_CLS_BASIC is not set +CONFIG_NET_CLS_TCINDEX=m +CONFIG_NET_CLS_ROUTE4=m +CONFIG_NET_CLS_ROUTE=y +CONFIG_NET_CLS_FW=m +CONFIG_NET_CLS_U32=m +# CONFIG_CLS_U32_PERF is not set +# CONFIG_CLS_U32_MARK is not set +CONFIG_NET_CLS_RSVP=m +CONFIG_NET_CLS_RSVP6=m +# CONFIG_NET_EMATCH is not set +# CONFIG_NET_CLS_ACT is not set +CONFIG_NET_CLS_POLICE=y +# CONFIG_NET_CLS_IND is not set +CONFIG_NET_ESTIMATOR=y + +# +# Network testing +# +CONFIG_NET_PKTGEN=m +CONFIG_HAMRADIO=y + +# +# Packet Radio protocols +# +CONFIG_AX25=m +# CONFIG_AX25_DAMA_SLAVE is not set +CONFIG_NETROM=m +CONFIG_ROSE=m + +# +# AX.25 network device drivers +# +CONFIG_MKISS=m +CONFIG_6PACK=m +CONFIG_BPQETHER=m +CONFIG_BAYCOM_SER_FDX=m +CONFIG_BAYCOM_SER_HDX=m +CONFIG_BAYCOM_PAR=m +CONFIG_BAYCOM_EPP=m +CONFIG_YAM=m +CONFIG_IRDA=m + +# +# IrDA protocols +# +CONFIG_IRLAN=m +CONFIG_IRNET=m +CONFIG_IRCOMM=m +# CONFIG_IRDA_ULTRA is not set + +# +# IrDA options +# +CONFIG_IRDA_CACHE_LAST_LSAP=y +CONFIG_IRDA_FAST_RR=y +CONFIG_IRDA_DEBUG=y + +# +# Infrared-port device drivers +# + +# +# SIR device drivers +# +CONFIG_IRTTY_SIR=m + +# +# Dongle support +# +CONFIG_DONGLE=y +CONFIG_ESI_DONGLE=m +CONFIG_ACTISYS_DONGLE=m +CONFIG_TEKRAM_DONGLE=m +# CONFIG_TOIM3232_DONGLE is not set +CONFIG_LITELINK_DONGLE=m +CONFIG_MA600_DONGLE=m +CONFIG_GIRBIL_DONGLE=m +CONFIG_MCP2120_DONGLE=m +CONFIG_OLD_BELKIN_DONGLE=m +CONFIG_ACT200L_DONGLE=m + +# +# Old SIR device drivers +# +CONFIG_IRPORT_SIR=m + +# +# Old Serial dongle support +# +# CONFIG_DONGLE_OLD is not set + +# +# FIR device drivers +# +CONFIG_USB_IRDA=m +CONFIG_SIGMATEL_FIR=m +CONFIG_BT=m +CONFIG_BT_L2CAP=m +CONFIG_BT_SCO=m +CONFIG_BT_RFCOMM=m +CONFIG_BT_RFCOMM_TTY=y +CONFIG_BT_BNEP=m +CONFIG_BT_BNEP_MC_FILTER=y +CONFIG_BT_BNEP_PROTO_FILTER=y +CONFIG_BT_CMTP=m +CONFIG_BT_HIDP=m + +# +# Bluetooth device drivers +# +CONFIG_BT_HCIUSB=m +CONFIG_BT_HCIUSB_SCO=y +CONFIG_BT_HCIUART=m +CONFIG_BT_HCIUART_H4=y +CONFIG_BT_HCIUART_BCSP=y +CONFIG_BT_HCIBCM203X=m +# CONFIG_BT_HCIBPA10X is not set +CONFIG_BT_HCIBFUSB=m +CONFIG_BT_HCIDTL1=m +CONFIG_BT_HCIBT3C=m +CONFIG_BT_HCIBLUECARD=m +CONFIG_BT_HCIBTUART=m +CONFIG_BT_HCIVHCI=m +CONFIG_IEEE80211=m +# CONFIG_IEEE80211_DEBUG is not set +# CONFIG_IEEE80211_CRYPT_WEP is not set +CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_IEEE80211_SOFTMAC is not set +CONFIG_WIRELESS_EXT=y + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=m +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=m +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=m +CONFIG_MTD_PARTITIONS=y +CONFIG_MTD_REDBOOT_PARTS=m +CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1 +# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set +# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set +# CONFIG_MTD_CMDLINE_PARTS is not set +# CONFIG_MTD_AFS_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=m +CONFIG_MTD_BLOCK=m +CONFIG_MTD_BLOCK_RO=m +CONFIG_FTL=m +CONFIG_NFTL=m +CONFIG_NFTL_RW=y +CONFIG_INFTL=m +# CONFIG_RFD_FTL is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=m +CONFIG_MTD_JEDECPROBE=m +CONFIG_MTD_GEN_PROBE=m +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +CONFIG_MTD_CFI_INTELEXT=m +CONFIG_MTD_CFI_AMDSTD=m +CONFIG_MTD_CFI_STAA=m +CONFIG_MTD_CFI_UTIL=m +CONFIG_MTD_RAM=m +CONFIG_MTD_ROM=m +CONFIG_MTD_ABSENT=m +# CONFIG_MTD_OBSOLETE_CHIPS is not set + +# +# Mapping drivers for chip access +# +CONFIG_MTD_COMPLEX_MAPPINGS=y +CONFIG_MTD_PHYSMAP=m +CONFIG_MTD_PHYSMAP_START=0x8000000 +CONFIG_MTD_PHYSMAP_LEN=0x4000000 +CONFIG_MTD_PHYSMAP_BANKWIDTH=2 +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +CONFIG_MTD_SLRAM=m +CONFIG_MTD_PHRAM=m +CONFIG_MTD_MTDRAM=m +CONFIG_MTDRAM_TOTAL_SIZE=4096 +CONFIG_MTDRAM_ERASE_SIZE=128 +CONFIG_MTD_BLKMTD=m +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +CONFIG_MTD_DOC2000=m +CONFIG_MTD_DOC2001=m +CONFIG_MTD_DOC2001PLUS=m +CONFIG_MTD_DOCPROBE=m +CONFIG_MTD_DOCECC=m +# CONFIG_MTD_DOCPROBE_ADVANCED is not set +CONFIG_MTD_DOCPROBE_ADDRESS=0 + +# +# NAND Flash Device Drivers +# +CONFIG_MTD_NAND=m +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +CONFIG_MTD_NAND_IDS=m +CONFIG_MTD_NAND_DISKONCHIP=m +# CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set +CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0 +# CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set +# CONFIG_MTD_NAND_NANDSIM is not set + +# +# OneNAND Flash Device Drivers +# +# CONFIG_MTD_ONENAND is not set + +# +# Parallel port support +# +CONFIG_PARPORT=m +CONFIG_PARPORT_PC=m +CONFIG_PARPORT_PC_FIFO=y +# CONFIG_PARPORT_PC_SUPERIO is not set +CONFIG_PARPORT_PC_PCMCIA=m +CONFIG_PARPORT_NOT_PC=y +# CONFIG_PARPORT_ARC is not set +# CONFIG_PARPORT_GSC is not set +CONFIG_PARPORT_1284=y + +# +# Plug and Play support +# + +# +# Block devices +# +CONFIG_PARIDE=m +CONFIG_PARIDE_PARPORT=m + +# +# Parallel IDE high-level drivers +# +CONFIG_PARIDE_PD=m +CONFIG_PARIDE_PCD=m +CONFIG_PARIDE_PF=m +CONFIG_PARIDE_PT=m +CONFIG_PARIDE_PG=m + +# +# Parallel IDE protocol modules +# +CONFIG_PARIDE_ATEN=m +CONFIG_PARIDE_BPCK=m +CONFIG_PARIDE_BPCK6=m +CONFIG_PARIDE_COMM=m +CONFIG_PARIDE_DSTR=m +CONFIG_PARIDE_FIT2=m +CONFIG_PARIDE_FIT3=m +CONFIG_PARIDE_EPAT=m +# CONFIG_PARIDE_EPATC8 is not set +CONFIG_PARIDE_EPIA=m +CONFIG_PARIDE_FRIQ=m +CONFIG_PARIDE_FRPW=m +CONFIG_PARIDE_KBIC=m +CONFIG_PARIDE_KTTI=m +CONFIG_PARIDE_ON20=m +CONFIG_PARIDE_ON26=m +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=m +CONFIG_BLK_DEV_CRYPTOLOOP=m +CONFIG_BLK_DEV_NBD=m +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +CONFIG_CDROM_PKTCDVD=m +CONFIG_CDROM_PKTCDVD_BUFFERS=8 +# CONFIG_CDROM_PKTCDVD_WCACHE is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +CONFIG_IDE=m +CONFIG_BLK_DEV_IDE=m + +# +# Please see Documentation/ide.txt for help/info on IDE drives +# +# CONFIG_BLK_DEV_IDE_SATA is not set +CONFIG_BLK_DEV_IDEDISK=m +# CONFIG_IDEDISK_MULTI_MODE is not set +CONFIG_BLK_DEV_IDECS=m +CONFIG_BLK_DEV_IDECD=m +CONFIG_BLK_DEV_IDETAPE=m +CONFIG_BLK_DEV_IDEFLOPPY=m +CONFIG_BLK_DEV_IDESCSI=m +# CONFIG_IDE_TASK_IOCTL is not set + +# +# IDE chipset support/bugfixes +# +CONFIG_IDE_GENERIC=m +# CONFIG_IDE_ARM is not set +# CONFIG_BLK_DEV_IDEDMA is not set +# CONFIG_IDEDMA_AUTO is not set +# CONFIG_BLK_DEV_HD is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=m +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=m +CONFIG_CHR_DEV_ST=m +CONFIG_CHR_DEV_OSST=m +CONFIG_BLK_DEV_SR=m +# CONFIG_BLK_DEV_SR_VENDOR is not set +CONFIG_CHR_DEV_SG=m +CONFIG_CHR_DEV_SCH=m + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +CONFIG_SCSI_CONSTANTS=y +CONFIG_SCSI_LOGGING=y + +# +# SCSI Transport Attributes +# +CONFIG_SCSI_SPI_ATTRS=m +CONFIG_SCSI_FC_ATTRS=m +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set + +# +# SCSI low-level drivers +# +# CONFIG_ISCSI_TCP is not set +CONFIG_SCSI_SATA=m +CONFIG_SCSI_PPA=m +CONFIG_SCSI_IMM=m +# CONFIG_SCSI_IZIP_EPP16 is not set +# CONFIG_SCSI_IZIP_SLOW_CTR is not set +CONFIG_SCSI_DEBUG=m + +# +# PCMCIA SCSI adapter support +# +CONFIG_PCMCIA_AHA152X=m +CONFIG_PCMCIA_FDOMAIN=m +CONFIG_PCMCIA_NINJA_SCSI=m +CONFIG_PCMCIA_QLOGIC=m +CONFIG_PCMCIA_SYM53C500=m + +# +# Multi-device support (RAID and LVM) +# +CONFIG_MD=y +CONFIG_BLK_DEV_MD=m +CONFIG_MD_LINEAR=m +CONFIG_MD_RAID0=m +CONFIG_MD_RAID1=m +CONFIG_MD_RAID10=m +CONFIG_MD_RAID5=m +# CONFIG_MD_RAID5_RESHAPE is not set +CONFIG_MD_RAID6=m +CONFIG_MD_MULTIPATH=m +CONFIG_MD_FAULTY=m +CONFIG_BLK_DEV_DM=m +CONFIG_DM_CRYPT=m +CONFIG_DM_SNAPSHOT=m +CONFIG_DM_MIRROR=m +CONFIG_DM_ZERO=m +# CONFIG_DM_MULTIPATH is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Network device support +# +CONFIG_NETDEVICES=y +CONFIG_DUMMY=m +CONFIG_BONDING=m +CONFIG_EQUALIZER=m +CONFIG_TUN=m + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=m +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +CONFIG_NET_POCKET=y +CONFIG_DE600=m +CONFIG_DE620=m + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +CONFIG_NET_RADIO=y +# CONFIG_NET_WIRELESS_RTNETLINK is not set + +# +# Obsolete Wireless cards support (pre-802.11) +# +CONFIG_STRIP=m +CONFIG_PCMCIA_WAVELAN=m +CONFIG_PCMCIA_NETWAVE=m + +# +# Wireless 802.11 Frequency Hopping cards support +# +CONFIG_PCMCIA_RAYCS=m + +# +# Wireless 802.11b ISA/PCI cards support +# +CONFIG_HERMES=m +CONFIG_ATMEL=m + +# +# Wireless 802.11b Pcmcia/Cardbus cards support +# +CONFIG_PCMCIA_HERMES=m +# CONFIG_PCMCIA_SPECTRUM is not set +CONFIG_AIRO_CS=m +CONFIG_PCMCIA_ATMEL=m +CONFIG_PCMCIA_WL3501=m +# CONFIG_HOSTAP is not set +CONFIG_NET_WIRELESS=y + +# +# PCMCIA network device support +# +CONFIG_NET_PCMCIA=y +CONFIG_PCMCIA_3C589=m +CONFIG_PCMCIA_3C574=m +CONFIG_PCMCIA_FMVJ18X=m +CONFIG_PCMCIA_PCNET=m +CONFIG_PCMCIA_NMCLAN=m +CONFIG_PCMCIA_SMC91C92=m +CONFIG_PCMCIA_XIRC2PS=m +CONFIG_PCMCIA_AXNET=m + +# +# Wan interfaces +# +CONFIG_WAN=y +CONFIG_SYNCLINK_SYNCPPP=m +CONFIG_HDLC=m +CONFIG_HDLC_RAW=y +CONFIG_HDLC_RAW_ETH=y +CONFIG_HDLC_CISCO=y +CONFIG_HDLC_FR=y +CONFIG_HDLC_PPP=y +CONFIG_HDLC_X25=y +CONFIG_DLCI=m +CONFIG_DLCI_COUNT=24 +CONFIG_DLCI_MAX=8 +CONFIG_WAN_ROUTER_DRIVERS=y +CONFIG_LAPBETHER=m +CONFIG_X25_ASY=m + +# +# ATM drivers +# +# CONFIG_ATM_DUMMY is not set +CONFIG_ATM_TCP=m +CONFIG_PLIP=m +CONFIG_PPP=m +CONFIG_PPP_MULTILINK=y +CONFIG_PPP_FILTER=y +CONFIG_PPP_ASYNC=m +CONFIG_PPP_SYNC_TTY=m +CONFIG_PPP_DEFLATE=m +CONFIG_PPP_BSDCOMP=m +CONFIG_PPP_MPPE=m +CONFIG_PPPOE=m +CONFIG_PPPOATM=m +CONFIG_SLIP=m +CONFIG_SLIP_COMPRESSED=y +CONFIG_SLIP_SMART=y +CONFIG_SLIP_MODE_SLIP6=y +CONFIG_SHAPER=m +CONFIG_NETCONSOLE=m +CONFIG_NETPOLL=y +# CONFIG_NETPOLL_RX is not set +# CONFIG_NETPOLL_TRAP is not set +CONFIG_NET_POLL_CONTROLLER=y + +# +# ISDN subsystem +# +CONFIG_ISDN=m + +# +# Old ISDN4Linux +# +CONFIG_ISDN_I4L=m +CONFIG_ISDN_PPP=y +CONFIG_ISDN_PPP_VJ=y +CONFIG_ISDN_MPP=y +CONFIG_IPPP_FILTER=y +CONFIG_ISDN_PPP_BSDCOMP=m +CONFIG_ISDN_AUDIO=y +CONFIG_ISDN_TTY_FAX=y +CONFIG_ISDN_X25=y + +# +# ISDN feature submodules +# +CONFIG_ISDN_DRV_LOOP=m +CONFIG_ISDN_DIVERSION=m + +# +# ISDN4Linux hardware drivers +# + +# +# Passive cards +# +CONFIG_ISDN_DRV_HISAX=m + +# +# D-channel protocol features +# +CONFIG_HISAX_EURO=y +CONFIG_DE_AOC=y +# CONFIG_HISAX_NO_SENDCOMPLETE is not set +# CONFIG_HISAX_NO_LLC is not set +# CONFIG_HISAX_NO_KEYPAD is not set +CONFIG_HISAX_1TR6=y +CONFIG_HISAX_NI1=y +CONFIG_HISAX_MAX_CARDS=8 + +# +# HiSax supported cards +# +CONFIG_HISAX_16_3=y +CONFIG_HISAX_S0BOX=y +CONFIG_HISAX_FRITZPCI=y +CONFIG_HISAX_AVM_A1_PCMCIA=y +CONFIG_HISAX_ELSA=y +CONFIG_HISAX_DIEHLDIVA=y +CONFIG_HISAX_SEDLBAUER=y +CONFIG_HISAX_NICCY=y +CONFIG_HISAX_GAZEL=y +CONFIG_HISAX_HFC_SX=y +# CONFIG_HISAX_DEBUG is not set + +# +# HiSax PCMCIA card service modules +# +CONFIG_HISAX_SEDLBAUER_CS=m +CONFIG_HISAX_ELSA_CS=m +CONFIG_HISAX_AVM_A1_CS=m +CONFIG_HISAX_TELES_CS=m + +# +# HiSax sub driver modules +# +CONFIG_HISAX_ST5481=m +CONFIG_HISAX_HFCUSB=m +# CONFIG_HISAX_HFC4S8S is not set +CONFIG_HISAX_HDLC=y + +# +# Active cards +# + +# +# Siemens Gigaset +# +# CONFIG_ISDN_DRV_GIGASET is not set + +# +# CAPI subsystem +# +CONFIG_ISDN_CAPI=m +CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y +CONFIG_ISDN_CAPI_MIDDLEWARE=y +CONFIG_ISDN_CAPI_CAPI20=m +CONFIG_ISDN_CAPI_CAPIFS_BOOL=y +CONFIG_ISDN_CAPI_CAPIFS=m +CONFIG_ISDN_CAPI_CAPIDRV=m + +# +# CAPI hardware drivers +# + +# +# Active AVM cards +# +CONFIG_CAPI_AVM=y +CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m +CONFIG_ISDN_DRV_AVMB1_AVM_CS=m + +# +# Active Eicon DIVA Server cards +# +CONFIG_CAPI_EICON=y + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=m +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +CONFIG_INPUT_JOYDEV=m +CONFIG_INPUT_TSDEV=m +CONFIG_INPUT_TSDEV_SCREEN_X=240 +CONFIG_INPUT_TSDEV_SCREEN_Y=320 +CONFIG_INPUT_EVDEV=m +CONFIG_INPUT_EVBUG=m + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +CONFIG_KEYBOARD_ATKBD=y +CONFIG_KEYBOARD_SUNKBD=m +CONFIG_KEYBOARD_LKKBD=m +CONFIG_KEYBOARD_XTKBD=m +CONFIG_KEYBOARD_NEWTON=m +CONFIG_INPUT_MOUSE=y +CONFIG_MOUSE_PS2=m +CONFIG_MOUSE_SERIAL=m +CONFIG_MOUSE_VSXXXAA=m +CONFIG_INPUT_JOYSTICK=y +CONFIG_JOYSTICK_ANALOG=m +CONFIG_JOYSTICK_A3D=m +CONFIG_JOYSTICK_ADI=m +CONFIG_JOYSTICK_COBRA=m +CONFIG_JOYSTICK_GF2K=m +CONFIG_JOYSTICK_GRIP=m +CONFIG_JOYSTICK_GRIP_MP=m +CONFIG_JOYSTICK_GUILLEMOT=m +CONFIG_JOYSTICK_INTERACT=m +CONFIG_JOYSTICK_SIDEWINDER=m +CONFIG_JOYSTICK_TMDC=m +CONFIG_JOYSTICK_IFORCE=m +CONFIG_JOYSTICK_IFORCE_USB=y +CONFIG_JOYSTICK_IFORCE_232=y +CONFIG_JOYSTICK_WARRIOR=m +CONFIG_JOYSTICK_MAGELLAN=m +CONFIG_JOYSTICK_SPACEORB=m +CONFIG_JOYSTICK_SPACEBALL=m +CONFIG_JOYSTICK_STINGER=m +# CONFIG_JOYSTICK_TWIDJOY is not set +CONFIG_JOYSTICK_DB9=m +CONFIG_JOYSTICK_GAMECON=m +CONFIG_JOYSTICK_TURBOGRAFX=m +CONFIG_JOYSTICK_JOYDUMP=m +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_GUNZE=m +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +CONFIG_INPUT_MISC=y +CONFIG_INPUT_UINPUT=m + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_SERPORT=m +CONFIG_SERIO_PARKBD=m +CONFIG_SERIO_LIBPS2=y +CONFIG_SERIO_RAW=m +CONFIG_GAMEPORT=m +CONFIG_GAMEPORT_NS558=m +CONFIG_GAMEPORT_L4=m + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +CONFIG_SERIAL_NONSTANDARD=y +CONFIG_COMPUTONE=m +CONFIG_ROCKETPORT=m +CONFIG_CYCLADES=m +# CONFIG_CYZ_INTR is not set +CONFIG_DIGIEPCA=m +CONFIG_MOXA_INTELLIO=m +CONFIG_MOXA_SMARTIO=m +# CONFIG_ISI is not set +CONFIG_SYNCLINKMP=m +CONFIG_N_HDLC=m +# CONFIG_RISCOM8 is not set +# CONFIG_SPECIALIX is not set +CONFIG_SX=m +CONFIG_RIO=m +CONFIG_RIO_OLDPCI=y +CONFIG_STALDRV=y +CONFIG_STALLION=m +CONFIG_ISTALLION=m + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_CS=m +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +# CONFIG_SERIAL_8250_DETECT_IRQ is not set +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +CONFIG_PRINTER=m +# CONFIG_LP_CONSOLE is not set +CONFIG_PPDEV=m +CONFIG_TIPAR=m + +# +# IPMI +# +CONFIG_IPMI_HANDLER=m +# CONFIG_IPMI_PANIC_EVENT is not set +CONFIG_IPMI_DEVICE_INTERFACE=m +CONFIG_IPMI_SI=m +CONFIG_IPMI_WATCHDOG=m +CONFIG_IPMI_POWEROFF=m + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +CONFIG_SOFT_WATCHDOG=m + +# +# USB-based Watchdog Cards +# +CONFIG_USBPCWATCHDOG=m +CONFIG_NVRAM=m +CONFIG_DTLK=m +CONFIG_R3964=m + +# +# Ftape, the floppy tape device driver +# + +# +# PCMCIA character devices +# +CONFIG_SYNCLINK_CS=m +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +CONFIG_RAW_DRIVER=m +CONFIG_MAX_RAW_DEVS=256 + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set + +# +# I2C support +# +CONFIG_I2C=m +CONFIG_I2C_CHARDEV=m + +# +# I2C Algorithms +# +CONFIG_I2C_ALGOBIT=m +CONFIG_I2C_ALGOPCF=m +CONFIG_I2C_ALGOPCA=m + +# +# I2C Hardware Bus support +# +CONFIG_I2C_ISA=m +CONFIG_I2C_PARPORT=m +CONFIG_I2C_PARPORT_LIGHT=m +CONFIG_I2C_STUB=m +CONFIG_I2C_PCA_ISA=m + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +CONFIG_SENSORS_EEPROM=m +CONFIG_SENSORS_PCF8574=m +# CONFIG_SENSORS_PCA9539 is not set +CONFIG_SENSORS_PCF8591=m +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +CONFIG_W1=m + +# +# 1-wire Bus Masters +# +# CONFIG_W1_MASTER_DS9490 is not set +# CONFIG_W1_MASTER_DS2482 is not set + +# +# 1-wire Slaves +# +# CONFIG_W1_SLAVE_THERM is not set +# CONFIG_W1_SLAVE_SMEM is not set +# CONFIG_W1_SLAVE_DS2433 is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +CONFIG_HWMON_VID=m +CONFIG_SENSORS_ADM1021=m +CONFIG_SENSORS_ADM1025=m +CONFIG_SENSORS_ADM1026=m +CONFIG_SENSORS_ADM1031=m +# CONFIG_SENSORS_ADM9240 is not set +CONFIG_SENSORS_ASB100=m +# CONFIG_SENSORS_ATXP1 is not set +CONFIG_SENSORS_DS1621=m +# CONFIG_SENSORS_F71805F is not set +CONFIG_SENSORS_FSCHER=m +# CONFIG_SENSORS_FSCPOS is not set +CONFIG_SENSORS_GL518SM=m +# CONFIG_SENSORS_GL520SM is not set +CONFIG_SENSORS_IT87=m +CONFIG_SENSORS_LM63=m +CONFIG_SENSORS_LM75=m +CONFIG_SENSORS_LM77=m +CONFIG_SENSORS_LM78=m +CONFIG_SENSORS_LM80=m +CONFIG_SENSORS_LM83=m +CONFIG_SENSORS_LM85=m +CONFIG_SENSORS_LM87=m +CONFIG_SENSORS_LM90=m +# CONFIG_SENSORS_LM92 is not set +CONFIG_SENSORS_MAX1619=m +CONFIG_SENSORS_PC87360=m +CONFIG_SENSORS_SMSC47M1=m +# CONFIG_SENSORS_SMSC47B397 is not set +CONFIG_SENSORS_W83781D=m +# CONFIG_SENSORS_W83792D is not set +CONFIG_SENSORS_W83L785TS=m +CONFIG_SENSORS_W83627HF=m +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Misc devices +# + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +CONFIG_DVB=y +CONFIG_DVB_CORE=m + +# +# Supported USB Adapters +# +# CONFIG_DVB_USB is not set +CONFIG_DVB_TTUSB_BUDGET=m +CONFIG_DVB_TTUSB_DEC=m +CONFIG_DVB_CINERGYT2=m +CONFIG_DVB_CINERGYT2_TUNING=y +CONFIG_DVB_CINERGYT2_STREAM_URB_COUNT=32 +CONFIG_DVB_CINERGYT2_STREAM_BUF_SIZE=512 +CONFIG_DVB_CINERGYT2_QUERY_INTERVAL=250 +CONFIG_DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE=y +CONFIG_DVB_CINERGYT2_RC_QUERY_INTERVAL=100 + +# +# Supported FlexCopII (B2C2) Adapters +# +# CONFIG_DVB_B2C2_FLEXCOP is not set + +# +# Supported DVB Frontends +# + +# +# Customise DVB Frontends +# + +# +# DVB-S (satellite) frontends +# +CONFIG_DVB_STV0299=m +CONFIG_DVB_CX24110=m +# CONFIG_DVB_CX24123 is not set +CONFIG_DVB_TDA8083=m +CONFIG_DVB_MT312=m +CONFIG_DVB_VES1X93=m +# CONFIG_DVB_S5H1420 is not set + +# +# DVB-T (terrestrial) frontends +# +CONFIG_DVB_SP8870=m +CONFIG_DVB_SP887X=m +CONFIG_DVB_CX22700=m +CONFIG_DVB_CX22702=m +CONFIG_DVB_L64781=m +CONFIG_DVB_TDA1004X=m +CONFIG_DVB_NXT6000=m +CONFIG_DVB_MT352=m +# CONFIG_DVB_ZL10353 is not set +CONFIG_DVB_DIB3000MB=m +CONFIG_DVB_DIB3000MC=m + +# +# DVB-C (cable) frontends +# +CONFIG_DVB_VES1820=m +CONFIG_DVB_TDA10021=m +CONFIG_DVB_STV0297=m + +# +# ATSC (North American/Korean Terresterial DTV) frontends +# +# CONFIG_DVB_NXT200X is not set +# CONFIG_DVB_OR51211 is not set +# CONFIG_DVB_OR51132 is not set +# CONFIG_DVB_BCM3510 is not set +# CONFIG_DVB_LGDT330X is not set +# CONFIG_USB_DABUSB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +CONFIG_SOUND=m + +# +# Advanced Linux Sound Architecture +# +CONFIG_SND=m +CONFIG_SND_TIMER=m +CONFIG_SND_PCM=m +CONFIG_SND_HWDEP=m +CONFIG_SND_RAWMIDI=m +CONFIG_SND_SEQUENCER=m +CONFIG_SND_SEQ_DUMMY=m +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=m +CONFIG_SND_PCM_OSS=m +CONFIG_SND_PCM_OSS_PLUGINS=y +CONFIG_SND_SEQUENCER_OSS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set + +# +# Generic devices +# +CONFIG_SND_MPU401_UART=m +CONFIG_SND_DUMMY=m +CONFIG_SND_VIRMIDI=m +CONFIG_SND_MTPAV=m +CONFIG_SND_SERIAL_U16550=m +CONFIG_SND_MPU401=m + +# +# ALSA ARM devices +# + +# +# USB devices +# +CONFIG_SND_USB_AUDIO=m + +# +# PCMCIA devices +# + +# +# Open Sound System +# +CONFIG_SOUND_PRIME=m +# CONFIG_OBSOLETE_OSS_DRIVER is not set +# CONFIG_SOUND_MSNDCLAS is not set +# CONFIG_SOUND_MSNDPIN is not set +CONFIG_SOUND_TVMIXER=m + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=m +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_BANDWIDTH=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_SUSPEND is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_SL811_HCD=m +# CONFIG_USB_SL811_CS is not set + +# +# USB Device Class drivers +# +CONFIG_USB_ACM=m +CONFIG_USB_PRINTER=m + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=m +# CONFIG_USB_STORAGE_DEBUG is not set +CONFIG_USB_STORAGE_DATAFAB=y +CONFIG_USB_STORAGE_FREECOM=y +CONFIG_USB_STORAGE_ISD200=y +CONFIG_USB_STORAGE_DPCM=y +CONFIG_USB_STORAGE_USBAT=y +CONFIG_USB_STORAGE_SDDR09=y +CONFIG_USB_STORAGE_SDDR55=y +CONFIG_USB_STORAGE_JUMPSHOT=y +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=m +CONFIG_USB_HIDINPUT=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +CONFIG_USB_HIDDEV=y + +# +# USB HID Boot Protocol drivers +# +CONFIG_USB_KBD=m +CONFIG_USB_MOUSE=m +CONFIG_USB_AIPTEK=m +CONFIG_USB_WACOM=m +# CONFIG_USB_ACECAD is not set +CONFIG_USB_KBTAB=m +CONFIG_USB_POWERMATE=m +CONFIG_USB_MTOUCH=m +# CONFIG_USB_ITMTOUCH is not set +CONFIG_USB_EGALAX=m +# CONFIG_USB_YEALINK is not set +CONFIG_USB_XPAD=m +CONFIG_USB_ATI_REMOTE=m +# CONFIG_USB_ATI_REMOTE2 is not set +# CONFIG_USB_KEYSPAN_REMOTE is not set +# CONFIG_USB_APPLETOUCH is not set + +# +# USB Imaging devices +# +CONFIG_USB_MDC800=m +CONFIG_USB_MICROTEK=m + +# +# USB Network Adapters +# +CONFIG_USB_CATC=m +CONFIG_USB_KAWETH=m +CONFIG_USB_PEGASUS=m +CONFIG_USB_RTL8150=m +CONFIG_USB_USBNET=m +CONFIG_USB_NET_AX8817X=m +CONFIG_USB_NET_CDCETHER=m +# CONFIG_USB_NET_GL620A is not set +CONFIG_USB_NET_NET1080=m +# CONFIG_USB_NET_PLUSB is not set +# CONFIG_USB_NET_RNDIS_HOST is not set +# CONFIG_USB_NET_CDC_SUBSET is not set +CONFIG_USB_NET_ZAURUS=m +# CONFIG_USB_ZD1201 is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# +CONFIG_USB_USS720=m + +# +# USB Serial Converter support +# +CONFIG_USB_SERIAL=m +CONFIG_USB_SERIAL_GENERIC=y +# CONFIG_USB_SERIAL_AIRPRIME is not set +# CONFIG_USB_SERIAL_ANYDATA is not set +CONFIG_USB_SERIAL_BELKIN=m +CONFIG_USB_SERIAL_WHITEHEAT=m +CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m +# CONFIG_USB_SERIAL_CP2101 is not set +CONFIG_USB_SERIAL_CYPRESS_M8=m +CONFIG_USB_SERIAL_EMPEG=m +CONFIG_USB_SERIAL_FTDI_SIO=m +CONFIG_USB_SERIAL_VISOR=m +CONFIG_USB_SERIAL_IPAQ=m +CONFIG_USB_SERIAL_IR=m +CONFIG_USB_SERIAL_EDGEPORT=m +CONFIG_USB_SERIAL_EDGEPORT_TI=m +# CONFIG_USB_SERIAL_GARMIN is not set +CONFIG_USB_SERIAL_IPW=m +CONFIG_USB_SERIAL_KEYSPAN_PDA=m +CONFIG_USB_SERIAL_KEYSPAN=m +# CONFIG_USB_SERIAL_KEYSPAN_MPR is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA28XA is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA28XB is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA19QW is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA19QI is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set +# CONFIG_USB_SERIAL_KEYSPAN_USA49WLC is not set +CONFIG_USB_SERIAL_KLSI=m +CONFIG_USB_SERIAL_KOBIL_SCT=m +CONFIG_USB_SERIAL_MCT_U232=m +# CONFIG_USB_SERIAL_NAVMAN is not set +CONFIG_USB_SERIAL_PL2303=m +# CONFIG_USB_SERIAL_HP4X is not set +CONFIG_USB_SERIAL_SAFE=m +# CONFIG_USB_SERIAL_SAFE_PADDED is not set +# CONFIG_USB_SERIAL_TI is not set +CONFIG_USB_SERIAL_CYBERJACK=m +CONFIG_USB_SERIAL_XIRCOM=m +CONFIG_USB_SERIAL_OMNINET=m +CONFIG_USB_EZUSB=y + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +CONFIG_USB_AUERSWALD=m +CONFIG_USB_RIO500=m +CONFIG_USB_LEGOTOWER=m +CONFIG_USB_LCD=m +CONFIG_USB_LED=m +CONFIG_USB_CYTHERM=m +CONFIG_USB_PHIDGETKIT=m +CONFIG_USB_PHIDGETSERVO=m +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_LD is not set +CONFIG_USB_TEST=m + +# +# USB DSL modem support +# +CONFIG_USB_ATM=m +CONFIG_USB_SPEEDTOUCH=m +# CONFIG_USB_CXACRU is not set +# CONFIG_USB_UEAGLEATM is not set +# CONFIG_USB_XUSBATM is not set + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=m +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_AT91 is not set +CONFIG_USB_GADGET_DUMMY_HCD=y +CONFIG_USB_DUMMY_HCD=m +CONFIG_USB_GADGET_DUALSPEED=y +CONFIG_USB_ZERO=m +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m + +# +# MMC/SD Card support +# +CONFIG_MMC=m +# CONFIG_MMC_DEBUG is not set +CONFIG_MMC_BLOCK=m + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +CONFIG_EXT2_FS_POSIX_ACL=y +CONFIG_EXT2_FS_SECURITY=y +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=m +CONFIG_EXT3_FS_XATTR=y +CONFIG_EXT3_FS_POSIX_ACL=y +CONFIG_EXT3_FS_SECURITY=y +CONFIG_JBD=m +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +CONFIG_REISERFS_FS=m +# CONFIG_REISERFS_CHECK is not set +# CONFIG_REISERFS_PROC_INFO is not set +CONFIG_REISERFS_FS_XATTR=y +CONFIG_REISERFS_FS_POSIX_ACL=y +CONFIG_REISERFS_FS_SECURITY=y +CONFIG_JFS_FS=m +CONFIG_JFS_POSIX_ACL=y +# CONFIG_JFS_SECURITY is not set +# CONFIG_JFS_DEBUG is not set +CONFIG_JFS_STATISTICS=y +CONFIG_FS_POSIX_ACL=y +CONFIG_XFS_FS=m +CONFIG_XFS_EXPORT=y +CONFIG_XFS_QUOTA=y +CONFIG_XFS_SECURITY=y +CONFIG_XFS_POSIX_ACL=y +CONFIG_XFS_RT=y +# CONFIG_OCFS2_FS is not set +CONFIG_MINIX_FS=m +CONFIG_ROMFS_FS=m +CONFIG_INOTIFY=y +CONFIG_QUOTA=y +CONFIG_QFMT_V1=m +CONFIG_QFMT_V2=m +CONFIG_QUOTACTL=y +CONFIG_DNOTIFY=y +CONFIG_AUTOFS_FS=m +CONFIG_AUTOFS4_FS=m +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y +CONFIG_ZISOFS=y +CONFIG_ZISOFS_FS=m +CONFIG_UDF_FS=m +CONFIG_UDF_NLS=y + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=m +CONFIG_MSDOS_FS=m +CONFIG_VFAT_FS=m +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +CONFIG_NTFS_FS=m +# CONFIG_NTFS_DEBUG is not set +# CONFIG_NTFS_RW is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +CONFIG_ADFS_FS=m +# CONFIG_ADFS_FS_RW is not set +CONFIG_AFFS_FS=m +CONFIG_HFS_FS=m +CONFIG_HFSPLUS_FS=m +CONFIG_BEFS_FS=m +# CONFIG_BEFS_DEBUG is not set +CONFIG_BFS_FS=m +CONFIG_EFS_FS=m +CONFIG_JFFS_FS=m +CONFIG_JFFS_FS_VERBOSE=0 +CONFIG_JFFS_PROC_FS=y +CONFIG_JFFS2_FS=m +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +CONFIG_VXFS_FS=m +CONFIG_HPFS_FS=m +CONFIG_QNX4FS_FS=m +CONFIG_SYSV_FS=m +CONFIG_UFS_FS=m + +# +# Network File Systems +# +CONFIG_NFS_FS=m +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +CONFIG_NFS_DIRECTIO=y +CONFIG_NFSD=m +CONFIG_NFSD_V3=y +# CONFIG_NFSD_V3_ACL is not set +CONFIG_NFSD_V4=y +CONFIG_NFSD_TCP=y +CONFIG_LOCKD=m +CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=m +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=m +CONFIG_SUNRPC_GSS=m +CONFIG_RPCSEC_GSS_KRB5=m +CONFIG_RPCSEC_GSS_SPKM3=m +CONFIG_SMB_FS=m +# CONFIG_SMB_NLS_DEFAULT is not set +CONFIG_CIFS=m +# CONFIG_CIFS_STATS is not set +# CONFIG_CIFS_XATTR is not set +# CONFIG_CIFS_EXPERIMENTAL is not set +CONFIG_NCP_FS=m +CONFIG_NCPFS_PACKET_SIGNING=y +CONFIG_NCPFS_IOCTL_LOCKING=y +CONFIG_NCPFS_STRONG=y +CONFIG_NCPFS_NFS_NS=y +CONFIG_NCPFS_OS2_NS=y +# CONFIG_NCPFS_SMALLDOS is not set +CONFIG_NCPFS_NLS=y +CONFIG_NCPFS_EXTRAS=y +CONFIG_CODA_FS=m +# CONFIG_CODA_FS_OLD_API is not set +CONFIG_AFS_FS=m +CONFIG_RXRPC=m +# CONFIG_9P_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +CONFIG_ACORN_PARTITION=y +# CONFIG_ACORN_PARTITION_CUMANA is not set +# CONFIG_ACORN_PARTITION_EESOX is not set +CONFIG_ACORN_PARTITION_ICS=y +# CONFIG_ACORN_PARTITION_ADFS is not set +# CONFIG_ACORN_PARTITION_POWERTEC is not set +CONFIG_ACORN_PARTITION_RISCIX=y +CONFIG_OSF_PARTITION=y +CONFIG_AMIGA_PARTITION=y +CONFIG_ATARI_PARTITION=y +CONFIG_MAC_PARTITION=y +CONFIG_MSDOS_PARTITION=y +CONFIG_BSD_DISKLABEL=y +CONFIG_MINIX_SUBPARTITION=y +CONFIG_SOLARIS_X86_PARTITION=y +CONFIG_UNIXWARE_DISKLABEL=y +CONFIG_LDM_PARTITION=y +# CONFIG_LDM_DEBUG is not set +CONFIG_SGI_PARTITION=y +CONFIG_ULTRIX_PARTITION=y +CONFIG_SUN_PARTITION=y +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set + +# +# Native Language Support +# +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="cp437" +CONFIG_NLS_CODEPAGE_437=m +CONFIG_NLS_CODEPAGE_737=m +CONFIG_NLS_CODEPAGE_775=m +CONFIG_NLS_CODEPAGE_850=m +CONFIG_NLS_CODEPAGE_852=m +CONFIG_NLS_CODEPAGE_855=m +CONFIG_NLS_CODEPAGE_857=m +CONFIG_NLS_CODEPAGE_860=m +CONFIG_NLS_CODEPAGE_861=m +CONFIG_NLS_CODEPAGE_862=m +CONFIG_NLS_CODEPAGE_863=m +CONFIG_NLS_CODEPAGE_864=m +CONFIG_NLS_CODEPAGE_865=m +CONFIG_NLS_CODEPAGE_866=m +CONFIG_NLS_CODEPAGE_869=m +CONFIG_NLS_CODEPAGE_936=m +CONFIG_NLS_CODEPAGE_950=m +CONFIG_NLS_CODEPAGE_932=m +CONFIG_NLS_CODEPAGE_949=m +CONFIG_NLS_CODEPAGE_874=m +CONFIG_NLS_ISO8859_8=m +CONFIG_NLS_CODEPAGE_1250=m +CONFIG_NLS_CODEPAGE_1251=m +CONFIG_NLS_ASCII=m +CONFIG_NLS_ISO8859_1=m +CONFIG_NLS_ISO8859_2=m +CONFIG_NLS_ISO8859_3=m +CONFIG_NLS_ISO8859_4=m +CONFIG_NLS_ISO8859_5=m +CONFIG_NLS_ISO8859_6=m +CONFIG_NLS_ISO8859_7=m +CONFIG_NLS_ISO8859_9=m +CONFIG_NLS_ISO8859_13=m +CONFIG_NLS_ISO8859_14=m +CONFIG_NLS_ISO8859_15=m +CONFIG_NLS_KOI8_R=m +CONFIG_NLS_KOI8_U=m +CONFIG_NLS_UTF8=m + +# +# Profiling support +# +CONFIG_PROFILING=y +CONFIG_OPROFILE=m + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +CONFIG_DEBUG_PREEMPT=y +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FRAME_POINTER=y +# CONFIG_UNWIND_INFO is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_DEBUG_USER is not set +# CONFIG_DEBUG_WAITQ is not set +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +CONFIG_SECURITY=y +# CONFIG_SECURITY_NETWORK is not set +CONFIG_SECURITY_CAPABILITIES=m +CONFIG_SECURITY_ROOTPLUG=m +CONFIG_SECURITY_SECLVL=m + +# +# Cryptographic options +# +CONFIG_CRYPTO=y +CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_NULL=m +CONFIG_CRYPTO_MD4=m +CONFIG_CRYPTO_MD5=y +CONFIG_CRYPTO_SHA1=m +CONFIG_CRYPTO_SHA256=m +CONFIG_CRYPTO_SHA512=m +CONFIG_CRYPTO_WP512=m +# CONFIG_CRYPTO_TGR192 is not set +CONFIG_CRYPTO_DES=m +CONFIG_CRYPTO_BLOWFISH=m +CONFIG_CRYPTO_TWOFISH=m +CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_AES=m +CONFIG_CRYPTO_CAST5=m +CONFIG_CRYPTO_CAST6=m +CONFIG_CRYPTO_TEA=m +CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_KHAZAD=m +CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_DEFLATE=m +CONFIG_CRYPTO_MICHAEL_MIC=m +CONFIG_CRYPTO_CRC32C=m +CONFIG_CRYPTO_TEST=m + +# +# Hardware crypto devices +# + +# +# Library routines +# +CONFIG_CRC_CCITT=m +CONFIG_CRC16=m +CONFIG_CRC32=y +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=m +CONFIG_REED_SOLOMON=m +CONFIG_REED_SOLOMON_DEC16=y diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S index dbcb11a31f7..b5bcebca1cd 100644 --- a/arch/arm/kernel/entry-common.S +++ b/arch/arm/kernel/entry-common.S @@ -271,7 +271,7 @@ ENTRY(sys_call_table) @ r8 = syscall table .type sys_syscall, #function sys_syscall: - eor scno, r0, #__NR_OABI_SYSCALL_BASE + bic scno, r0, #__NR_OABI_SYSCALL_BASE cmp scno, #__NR_syscall - __NR_SYSCALL_BASE cmpne scno, #NR_syscalls @ check range stmloia sp, {r5, r6} @ shuffle args diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c index 2d5896b3618..bcc19fbb32d 100644 --- a/arch/arm/kernel/irq.c +++ b/arch/arm/kernel/irq.c @@ -342,10 +342,10 @@ __do_irq(unsigned int irq, struct irqaction *action, struct pt_regs *regs) #ifdef CONFIG_NO_IDLE_HZ if (!(action->flags & SA_TIMER) && system_timer->dyn_tick != NULL) { - write_seqlock(&xtime_lock); + spin_lock(&system_timer->dyn_tick->lock); if (system_timer->dyn_tick->state & DYN_TICK_ENABLED) system_timer->dyn_tick->handler(irq, 0, regs); - write_sequnlock(&xtime_lock); + spin_unlock(&system_timer->dyn_tick->lock); } #endif diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c index d6bd435a685..9c12d4fefbd 100644 --- a/arch/arm/kernel/time.c +++ b/arch/arm/kernel/time.c @@ -379,7 +379,7 @@ static int timer_dyn_tick_enable(void) int ret = -ENODEV; if (dyn_tick) { - write_seqlock_irqsave(&xtime_lock, flags); + spin_lock_irqsave(&dyn_tick->lock, flags); ret = 0; if (!(dyn_tick->state & DYN_TICK_ENABLED)) { ret = dyn_tick->enable(); @@ -387,7 +387,7 @@ static int timer_dyn_tick_enable(void) if (ret == 0) dyn_tick->state |= DYN_TICK_ENABLED; } - write_sequnlock_irqrestore(&xtime_lock, flags); + spin_unlock_irqrestore(&dyn_tick->lock, flags); } return ret; @@ -400,7 +400,7 @@ static int timer_dyn_tick_disable(void) int ret = -ENODEV; if (dyn_tick) { - write_seqlock_irqsave(&xtime_lock, flags); + spin_lock_irqsave(&dyn_tick->lock, flags); ret = 0; if (dyn_tick->state & DYN_TICK_ENABLED) { ret = dyn_tick->disable(); @@ -408,7 +408,7 @@ static int timer_dyn_tick_disable(void) if (ret == 0) dyn_tick->state &= ~DYN_TICK_ENABLED; } - write_sequnlock_irqrestore(&xtime_lock, flags); + spin_unlock_irqrestore(&dyn_tick->lock, flags); } return ret; @@ -422,15 +422,20 @@ static int timer_dyn_tick_disable(void) void timer_dyn_reprogram(void) { struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick; - unsigned long next, seq; + unsigned long next, seq, flags; - if (dyn_tick && (dyn_tick->state & DYN_TICK_ENABLED)) { + if (!dyn_tick) + return; + + spin_lock_irqsave(&dyn_tick->lock, flags); + if (dyn_tick->state & DYN_TICK_ENABLED) { next = next_timer_interrupt(); do { seq = read_seqbegin(&xtime_lock); - dyn_tick->reprogram(next_timer_interrupt() - jiffies); + dyn_tick->reprogram(next - jiffies); } while (read_seqretry(&xtime_lock, seq)); } + spin_unlock_irqrestore(&dyn_tick->lock, flags); } static ssize_t timer_show_dyn_tick(struct sys_device *dev, char *buf) @@ -499,5 +504,10 @@ void __init time_init(void) if (system_timer->offset == NULL) system_timer->offset = dummy_gettimeoffset; system_timer->init(); + +#ifdef CONFIG_NO_IDLE_HZ + if (system_timer->dyn_tick) + system_timer->dyn_tick->lock = SPIN_LOCK_UNLOCKED; +#endif } diff --git a/arch/arm/mach-lh7a40x/Kconfig b/arch/arm/mach-lh7a40x/Kconfig index 8a17867a6a2..558a34f53b1 100644 --- a/arch/arm/mach-lh7a40x/Kconfig +++ b/arch/arm/mach-lh7a40x/Kconfig @@ -14,6 +14,7 @@ config MACH_LPD7A400 bool "LPD7A400 Card Engine" select ARCH_LH7A400 # select IDE_POLL + select HAS_TOUCHSCREEN_ADS7843_LH7 help Say Y here if you are using Logic Product Development's LPD7A400 CardEngine. For the time being, the LPD7A400 and @@ -23,6 +24,7 @@ config MACH_LPD7A404 bool "LPD7A404 Card Engine" select ARCH_LH7A404 # select IDE_POLL + select HAS_TOUCHSCREEN_ADC_LH7 help Say Y here if you are using Logic Product Development's LPD7A404 CardEngine. For the time being, the LPD7A400 and @@ -34,6 +36,9 @@ config ARCH_LH7A400 config ARCH_LH7A404 bool +config LPD7A40X_CPLD_SSP + bool + config LH7A40X_CONTIGMEM bool "Disable NUMA Support" depends on ARCH_LH7A40X diff --git a/arch/arm/mach-lh7a40x/Makefile b/arch/arm/mach-lh7a40x/Makefile index e90512dbc2d..94b8615fb3c 100644 --- a/arch/arm/mach-lh7a40x/Makefile +++ b/arch/arm/mach-lh7a40x/Makefile @@ -4,11 +4,14 @@ # Object file lists. -obj-y := time.o -obj-$(CONFIG_MACH_KEV7A400) += arch-kev7a400.o irq-lh7a400.o -obj-$(CONFIG_MACH_LPD7A400) += arch-lpd7a40x.o irq-lh7a400.o -obj-$(CONFIG_MACH_LPD7A404) += arch-lpd7a40x.o irq-lh7a404.o - -obj-m := -obj-n := -obj- := +obj-y := time.o clocks.o +obj-m := +obj-n := +obj- := + +obj-$(CONFIG_MACH_KEV7A400) += arch-kev7a400.o irq-lh7a400.o +obj-$(CONFIG_MACH_LPD7A400) += arch-lpd7a40x.o irq-lh7a400.o +obj-$(CONFIG_MACH_LPD7A404) += arch-lpd7a40x.o irq-lh7a404.o +obj-$(CONFIG_LPD7A40X_CPLD_SSP) += ssp-cpld.o +obj-$(CONFIG_FB_ARMCLCD) += clcd.o + diff --git a/arch/arm/mach-lh7a40x/arch-lpd7a40x.c b/arch/arm/mach-lh7a40x/arch-lpd7a40x.c index 12e23277c5e..c0e6854289f 100644 --- a/arch/arm/mach-lh7a40x/arch-lpd7a40x.c +++ b/arch/arm/mach-lh7a40x/arch-lpd7a40x.c @@ -23,6 +23,28 @@ #include "common.h" +#define CPLD_INT_NETHERNET (1<<0) +#define CPLD_INTMASK_ETHERNET (1<<2) +#if defined (CONFIG_MACH_LPD7A400) +# define CPLD_INT_NTOUCH (1<<1) +# define CPLD_INTMASK_TOUCH (1<<3) +# define CPLD_INT_PEN (1<<4) +# define CPLD_INTMASK_PEN (1<<4) +# define CPLD_INT_PIRQ (1<<4) +#endif +#define CPLD_INTMASK_CPLD (1<<7) +#define CPLD_INT_CPLD (1<<6) + +#define CPLD_CONTROL_SWINT (1<<7) /* Disable all CPLD IRQs */ +#define CPLD_CONTROL_OCMSK (1<<6) /* Mask USB1 connect IRQ */ +#define CPLD_CONTROL_PDRV (1<<5) /* PCC_nDRV high */ +#define CPLD_CONTROL_USB1C (1<<4) /* USB1 connect IRQ active */ +#define CPLD_CONTROL_USB1P (1<<3) /* USB1 power disable */ +#define CPLD_CONTROL_AWKP (1<<2) /* Auto-wakeup disabled */ +#define CPLD_CONTROL_LCD_ENABLE (1<<1) /* LCD Vee enable */ +#define CPLD_CONTROL_WRLAN_NENABLE (1<<0) /* SMC91x power disable */ + + static struct resource smc91x_resources[] = { [0] = { .start = CPLD00_PHYS, @@ -48,12 +70,12 @@ static struct platform_device smc91x_device = { static struct resource lh7a40x_usbclient_resources[] = { [0] = { .start = USB_PHYS, - .end = (USB_PHYS + 0xFF), + .end = (USB_PHYS + PAGE_SIZE), .flags = IORESOURCE_MEM, }, [1] = { - .start = IRQ_USBINTR, - .end = IRQ_USBINTR, + .start = IRQ_USB, + .end = IRQ_USB, .flags = IORESOURCE_IRQ, }, }; @@ -61,7 +83,8 @@ static struct resource lh7a40x_usbclient_resources[] = { static u64 lh7a40x_usbclient_dma_mask = 0xffffffffUL; static struct platform_device lh7a40x_usbclient_device = { - .name = "lh7a40x_udc", +// .name = "lh7a40x_udc", + .name = "lh7-udc", .id = 0, .dev = { .dma_mask = &lh7a40x_usbclient_dma_mask, @@ -101,7 +124,7 @@ static struct platform_device lh7a404_usbhost_device = { #endif -static struct platform_device *lpd7a40x_devs[] __initdata = { +static struct platform_device* lpd7a40x_devs[] __initdata = { &smc91x_device, &lh7a40x_usbclient_device, #if defined (CONFIG_ARCH_LH7A404) @@ -113,29 +136,52 @@ extern void lpd7a400_map_io (void); static void __init lpd7a40x_init (void) { - CPLD_CONTROL |= (1<<6); /* Mask USB1 connection IRQ */ +#if defined (CONFIG_MACH_LPD7A400) + CPLD_CONTROL |= 0 + | CPLD_CONTROL_SWINT /* Disable software interrupt */ + | CPLD_CONTROL_OCMSK; /* Mask USB1 connection IRQ */ CPLD_CONTROL &= ~(0 - | (1<<1) /* Disable LCD */ - | (1<<0) /* Enable WLAN */ + | CPLD_CONTROL_LCD_ENABLE /* Disable LCD */ + | CPLD_CONTROL_WRLAN_NENABLE /* Enable SMC91x */ ); +#endif + +#if defined (CONFIG_MACH_LPD7A404) + CPLD_CONTROL &= ~(0 + | CPLD_CONTROL_WRLAN_NENABLE /* Enable SMC91x */ + ); +#endif platform_add_devices (lpd7a40x_devs, ARRAY_SIZE (lpd7a40x_devs)); +#if defined (CONFIG_FB_ARMCLCD) + lh7a40x_clcd_init (); +#endif } static void lh7a40x_ack_cpld_irq (u32 irq) { - /* CPLD doesn't have ack capability */ + /* CPLD doesn't have ack capability, but some devices may */ + +#if defined (CPLD_INTMASK_TOUCH) + /* The touch control *must* mask the the interrupt because the + * interrupt bit is read by the driver to determine if the pen + * is still down. */ + if (irq == IRQ_TOUCH) + CPLD_INTERRUPTS |= CPLD_INTMASK_TOUCH; +#endif } static void lh7a40x_mask_cpld_irq (u32 irq) { switch (irq) { case IRQ_LPD7A40X_ETH_INT: - CPLD_INTERRUPTS = CPLD_INTERRUPTS | 0x4; + CPLD_INTERRUPTS |= CPLD_INTMASK_ETHERNET; break; - case IRQ_LPD7A400_TS: - CPLD_INTERRUPTS = CPLD_INTERRUPTS | 0x8; +#if defined (IRQ_TOUCH) + case IRQ_TOUCH: + CPLD_INTERRUPTS |= CPLD_INTMASK_TOUCH; break; +#endif } } @@ -143,11 +189,13 @@ static void lh7a40x_unmask_cpld_irq (u32 irq) { switch (irq) { case IRQ_LPD7A40X_ETH_INT: - CPLD_INTERRUPTS = CPLD_INTERRUPTS & ~ 0x4; + CPLD_INTERRUPTS &= ~CPLD_INTMASK_ETHERNET; break; - case IRQ_LPD7A400_TS: - CPLD_INTERRUPTS = CPLD_INTERRUPTS & ~ 0x8; +#if defined (IRQ_TOUCH) + case IRQ_TOUCH: + CPLD_INTERRUPTS &= ~CPLD_INTMASK_TOUCH; break; +#endif } } @@ -164,11 +212,13 @@ static void lpd7a40x_cpld_handler (unsigned int irq, struct irqdesc *desc, desc->chip->ack (irq); - if ((mask & 0x1) == 0) /* WLAN */ + if ((mask & (1<<0)) == 0) /* WLAN */ IRQ_DISPATCH (IRQ_LPD7A40X_ETH_INT); - if ((mask & 0x2) == 0) /* Touch */ - IRQ_DISPATCH (IRQ_LPD7A400_TS); +#if defined (IRQ_TOUCH) + if ((mask & (1<<1)) == 0) /* Touch */ + IRQ_DISPATCH (IRQ_TOUCH); +#endif desc->chip->unmask (irq); /* Level-triggered need this */ } @@ -204,9 +254,21 @@ void __init lh7a40x_init_board_irq (void) /* Then, configure CPLD interrupt */ - CPLD_INTERRUPTS = 0x9c; /* Disable all CPLD interrupts */ + /* Disable all CPLD interrupts */ +#if defined (CONFIG_MACH_LPD7A400) + CPLD_INTERRUPTS = CPLD_INTMASK_TOUCH | CPLD_INTMASK_PEN + | CPLD_INTMASK_ETHERNET; + /* *** FIXME: don't know why we need 7 and 4. 7 is way wrong + and 4 is uncefined. */ + // (1<<7)|(1<<4)|(1<<3)|(1<<2); +#endif +#if defined (CONFIG_MACH_LPD7A404) + CPLD_INTERRUPTS = CPLD_INTMASK_ETHERNET; + /* *** FIXME: don't know why we need 6 and 5, neither is defined. */ + // (1<<6)|(1<<5)|(1<<3); +#endif GPIO_PFDD &= ~(1 << pinCPLD); /* Make input */ - GPIO_INTTYPE1 |= (1 << pinCPLD); /* Edge triggered */ + GPIO_INTTYPE1 &= ~(1 << pinCPLD); /* Level triggered */ GPIO_INTTYPE2 &= ~(1 << pinCPLD); /* Active low */ barrier (); GPIO_GPIOFINTEN |= (1 << pinCPLD); /* Enable */ @@ -216,7 +278,7 @@ void __init lh7a40x_init_board_irq (void) for (irq = IRQ_BOARD_START; irq < IRQ_BOARD_START + NR_IRQ_BOARD; ++irq) { set_irq_chip (irq, &lpd7a40x_cpld_chip); - set_irq_handler (irq, do_edge_IRQ); + set_irq_handler (irq, do_level_IRQ); set_irq_flags (irq, IRQF_VALID); } @@ -226,91 +288,109 @@ void __init lh7a40x_init_board_irq (void) lpd7a40x_cpld_handler); } -static struct map_desc lpd7a400_io_desc[] __initdata = { +static struct map_desc lpd7a40x_io_desc[] __initdata = { { - .virtual = IO_VIRT, + .virtual = IO_VIRT, .pfn = __phys_to_pfn(IO_PHYS), - .length = IO_SIZE, + .length = IO_SIZE, .type = MT_DEVICE - }, { /* Mapping added to work around chip select problems */ + }, + { /* Mapping added to work around chip select problems */ .virtual = IOBARRIER_VIRT, .pfn = __phys_to_pfn(IOBARRIER_PHYS), .length = IOBARRIER_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CF_VIRT, .pfn = __phys_to_pfn(CF_PHYS), - .length = CF_SIZE, + .length = CF_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD02_VIRT, .pfn = __phys_to_pfn(CPLD02_PHYS), - .length = CPLD02_SIZE, + .length = CPLD02_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD06_VIRT, .pfn = __phys_to_pfn(CPLD06_PHYS), - .length = CPLD06_SIZE, + .length = CPLD06_SIZE, + .type = MT_DEVICE + }, + { + .virtual = CPLD08_VIRT, + .pfn = __phys_to_pfn(CPLD08_PHYS), + .length = CPLD08_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD08_VIRT, .pfn = __phys_to_pfn(CPLD08_PHYS), - .length = CPLD08_SIZE, + .length = CPLD08_SIZE, .type = MT_DEVICE - }, { + }, + { + .virtual = CPLD0A_VIRT, + .pfn = __phys_to_pfn(CPLD0A_PHYS), + .length = CPLD0A_SIZE, + .type = MT_DEVICE + }, + { .virtual = CPLD0C_VIRT, .pfn = __phys_to_pfn(CPLD0C_PHYS), - .length = CPLD0C_SIZE, + .length = CPLD0C_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD0E_VIRT, .pfn = __phys_to_pfn(CPLD0E_PHYS), - .length = CPLD0E_SIZE, + .length = CPLD0E_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD10_VIRT, .pfn = __phys_to_pfn(CPLD10_PHYS), - .length = CPLD10_SIZE, + .length = CPLD10_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD12_VIRT, .pfn = __phys_to_pfn(CPLD12_PHYS), - .length = CPLD12_SIZE, + .length = CPLD12_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD14_VIRT, .pfn = __phys_to_pfn(CPLD14_PHYS), - .length = CPLD14_SIZE, + .length = CPLD14_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD16_VIRT, .pfn = __phys_to_pfn(CPLD16_PHYS), - .length = CPLD16_SIZE, + .length = CPLD16_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD18_VIRT, .pfn = __phys_to_pfn(CPLD18_PHYS), - .length = CPLD18_SIZE, + .length = CPLD18_SIZE, .type = MT_DEVICE - }, { + }, + { .virtual = CPLD1A_VIRT, .pfn = __phys_to_pfn(CPLD1A_PHYS), - .length = CPLD1A_SIZE, + .length = CPLD1A_SIZE, .type = MT_DEVICE }, - /* This mapping is redundant since the smc driver performs another. */ -/* { CPLD00_VIRT, CPLD00_PHYS, CPLD00_SIZE, MT_DEVICE }, */ }; void __init -lpd7a400_map_io(void) +lpd7a40x_map_io(void) { - iotable_init (lpd7a400_io_desc, ARRAY_SIZE (lpd7a400_io_desc)); - - /* Fixup (improve) Static Memory Controller settings */ - SMC_BCR0 = 0x200039af; /* Boot Flash */ - SMC_BCR6 = 0x1000fbe0; /* CPLD */ - SMC_BCR7 = 0x1000b2c2; /* Compact Flash */ + iotable_init (lpd7a40x_io_desc, ARRAY_SIZE (lpd7a40x_io_desc)); } #ifdef CONFIG_MACH_LPD7A400 @@ -320,7 +400,7 @@ MACHINE_START (LPD7A400, "Logic Product Development LPD7A400-10") .phys_io = 0x80000000, .io_pg_offst = ((io_p2v (0x80000000))>>18) & 0xfffc, .boot_params = 0xc0000100, - .map_io = lpd7a400_map_io, + .map_io = lpd7a40x_map_io, .init_irq = lh7a400_init_irq, .timer = &lh7a40x_timer, .init_machine = lpd7a40x_init, @@ -335,7 +415,7 @@ MACHINE_START (LPD7A404, "Logic Product Development LPD7A404-10") .phys_io = 0x80000000, .io_pg_offst = ((io_p2v (0x80000000))>>18) & 0xfffc, .boot_params = 0xc0000100, - .map_io = lpd7a400_map_io, + .map_io = lpd7a40x_map_io, .init_irq = lh7a404_init_irq, .timer = &lh7a40x_timer, .init_machine = lpd7a40x_init, diff --git a/arch/arm/mach-lh7a40x/clcd.c b/arch/arm/mach-lh7a40x/clcd.c new file mode 100644 index 00000000000..93751fee793 --- /dev/null +++ b/arch/arm/mach-lh7a40x/clcd.c @@ -0,0 +1,241 @@ +/* + * arch/arm/mach-lh7a40x/clcd.c + * + * Copyright (C) 2004 Marc Singer + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + */ +#include <linux/config.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/dma-mapping.h> +#include <linux/sysdev.h> +#include <linux/interrupt.h> + +//#include <linux/module.h> +//#include <linux/time.h> +//#include <asm/hardware.h> + +//#include <asm/mach/time.h> +#include <asm/irq.h> +#include <asm/mach/irq.h> + +#include <asm/system.h> +#include <asm/hardware.h> +#include <linux/amba/bus.h> +#include <linux/amba/clcd.h> + +#define HRTFTC_HRSETUP __REG(HRTFTC_PHYS + 0x00) +#define HRTFTC_HRCON __REG(HRTFTC_PHYS + 0x04) +#define HRTFTC_HRTIMING1 __REG(HRTFTC_PHYS + 0x08) +#define HRTFTC_HRTIMING2 __REG(HRTFTC_PHYS + 0x0c) + +#define ALI_SETUP __REG(ALI_PHYS + 0x00) +#define ALI_CONTROL __REG(ALI_PHYS + 0x04) +#define ALI_TIMING1 __REG(ALI_PHYS + 0x08) +#define ALI_TIMING2 __REG(ALI_PHYS + 0x0c) + +#include "lcd-panel.h" + +static void lh7a40x_clcd_disable (struct clcd_fb *fb) +{ +#if defined (CONFIG_MACH_LPD7A400) + CPLD_CONTROL &= ~(1<<1); /* Disable LCD Vee */ +#endif + +#if defined (CONFIG_MACH_LPD7A404) + GPIO_PCD &= ~(1<<3); /* Disable LCD Vee */ +#endif + +#if defined (CONFIG_ARCH_LH7A400) + HRTFTC_HRSETUP &= ~(1<<13); /* Disable HRTFT controller */ +#endif + +#if defined (CONFIG_ARCH_LH7A404) + ALI_SETUP &= ~(1<<13); /* Disable ALI */ +#endif +} + +static void lh7a40x_clcd_enable (struct clcd_fb *fb) +{ + struct clcd_panel_extra* extra + = (struct clcd_panel_extra*) fb->board_data; + +#if defined (CONFIG_MACH_LPD7A400) + CPLD_CONTROL |= (1<<1); /* Enable LCD Vee */ +#endif + +#if defined (CONFIG_MACH_LPD7A404) + GPIO_PCDD &= ~(1<<3); /* Enable LCD Vee */ + GPIO_PCD |= (1<<3); +#endif + +#if defined (CONFIG_ARCH_LH7A400) + + if (extra) { + HRTFTC_HRSETUP + = (1 << 13) + | ((fb->fb.var.xres - 1) << 4) + | 0xc + | (extra->hrmode ? 1 : 0); + HRTFTC_HRCON + = ((extra->clsen ? 1 : 0) << 1) + | ((extra->spsen ? 1 : 0) << 0); + HRTFTC_HRTIMING1 + = (extra->pcdel << 8) + | (extra->revdel << 4) + | (extra->lpdel << 0); + HRTFTC_HRTIMING2 + = (extra->spldel << 9) + | (extra->pc2del << 0); + } + else + HRTFTC_HRSETUP + = (1 << 13) + | 0xc; +#endif + +#if defined (CONFIG_ARCH_LH7A404) + + if (extra) { + ALI_SETUP + = (1 << 13) + | ((fb->fb.var.xres - 1) << 4) + | 0xc + | (extra->hrmode ? 1 : 0); + ALI_CONTROL + = ((extra->clsen ? 1 : 0) << 1) + | ((extra->spsen ? 1 : 0) << 0); + ALI_TIMING1 + = (extra->pcdel << 8) + | (extra->revdel << 4) + | (extra->lpdel << 0); + ALI_TIMING2 + = (extra->spldel << 9) + | (extra->pc2del << 0); + } + else + ALI_SETUP + = (1 << 13) + | 0xc; +#endif + +} + +#define FRAMESIZE(s) (((s) + PAGE_SIZE - 1)&PAGE_MASK) + +static int lh7a40x_clcd_setup (struct clcd_fb *fb) +{ + dma_addr_t dma; + u32 len = FRAMESIZE (lcd_panel.mode.xres*lcd_panel.mode.yres + *(lcd_panel.bpp/8)); + + fb->panel = &lcd_panel; + + /* Enforce the sync polarity defaults */ + if (!(fb->panel->tim2 & TIM2_IHS)) + fb->fb.var.sync |= FB_SYNC_HOR_HIGH_ACT; + if (!(fb->panel->tim2 & TIM2_IVS)) + fb->fb.var.sync |= FB_SYNC_VERT_HIGH_ACT; + +#if defined (HAS_LCD_PANEL_EXTRA) + fb->board_data = &lcd_panel_extra; +#endif + + fb->fb.screen_base + = dma_alloc_writecombine (&fb->dev->dev, len, + &dma, GFP_KERNEL); + printk ("CLCD: LCD setup fb virt 0x%p phys 0x%p l %x io 0x%p \n", + fb->fb.screen_base, (void*) dma, len, + (void*) io_p2v (CLCDC_PHYS)); + printk ("CLCD: pixclock %d\n", lcd_panel.mode.pixclock); + + if (!fb->fb.screen_base) { + printk(KERN_ERR "CLCD: unable to map framebuffer\n"); + return -ENOMEM; + } + +#if defined (USE_RGB555) + fb->fb.var.green.length = 5; /* Panel uses RGB 5:5:5 */ +#endif + + fb->fb.fix.smem_start = dma; + fb->fb.fix.smem_len = len; + + /* Drive PE4 high to prevent CPLD crash */ + GPIO_PEDD |= (1<<4); + GPIO_PED |= (1<<4); + + GPIO_PINMUX |= (1<<1) | (1<<0); /* LCDVD[15:4] */ + +// fb->fb.fbops->fb_check_var (&fb->fb.var, &fb->fb); +// fb->fb.fbops->fb_set_par (&fb->fb); + + return 0; +} + +static int lh7a40x_clcd_mmap (struct clcd_fb *fb, struct vm_area_struct *vma) +{ + return dma_mmap_writecombine(&fb->dev->dev, vma, + fb->fb.screen_base, + fb->fb.fix.smem_start, + fb->fb.fix.smem_len); +} + +static void lh7a40x_clcd_remove (struct clcd_fb *fb) +{ + dma_free_writecombine (&fb->dev->dev, fb->fb.fix.smem_len, + fb->fb.screen_base, fb->fb.fix.smem_start); +} + +static struct clcd_board clcd_platform_data = { + .name = "lh7a40x FB", + .check = clcdfb_check, + .decode = clcdfb_decode, + .enable = lh7a40x_clcd_enable, + .setup = lh7a40x_clcd_setup, + .mmap = lh7a40x_clcd_mmap, + .remove = lh7a40x_clcd_remove, + .disable = lh7a40x_clcd_disable, +}; + +#define IRQ_CLCDC (IRQ_LCDINTR) + +#define AMBA_DEVICE(name,busid,base,plat,pid) \ +static struct amba_device name##_device = { \ + .dev = { \ + .coherent_dma_mask = ~0, \ + .bus_id = busid, \ + .platform_data = plat, \ + }, \ + .res = { \ + .start = base##_PHYS, \ + .end = (base##_PHYS) + (4*1024) - 1, \ + .flags = IORESOURCE_MEM, \ + }, \ + .dma_mask = ~0, \ + .irq = { IRQ_##base, }, \ + /* .dma = base##_DMA,*/ \ + .periphid = pid, \ +} + +AMBA_DEVICE(clcd, "cldc-lh7a40x", CLCDC, &clcd_platform_data, 0x41110); + +static struct amba_device *amba_devs[] __initdata = { + &clcd_device, +}; + +void __init lh7a40x_clcd_init (void) +{ + int i; + int result; + printk ("CLCD: registering amba devices\n"); + for (i = 0; i < ARRAY_SIZE(amba_devs); i++) { + struct amba_device *d = amba_devs[i]; + result = amba_device_register(d, &iomem_resource); + printk (" %d -> %d\n", i ,result); + } +} diff --git a/arch/arm/mach-lh7a40x/clocks.c b/arch/arm/mach-lh7a40x/clocks.c new file mode 100644 index 00000000000..2291afe9f23 --- /dev/null +++ b/arch/arm/mach-lh7a40x/clocks.c @@ -0,0 +1,199 @@ +/* arch/arm/mach-lh7a40x/clocks.c + * + * Copyright (C) 2004 Marc Singer + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + */ + +#include <linux/config.h> +#include <linux/cpufreq.h> +#include <asm/hardware.h> +#include <asm/arch/clocks.h> +#include <linux/err.h> + +struct module; +struct icst525_params; + +struct clk { + struct list_head node; + unsigned long rate; + struct module *owner; + const char *name; +// void *data; +// const struct icst525_params *params; +// void (*setvco)(struct clk *, struct icst525_vco vco); +}; + +int clk_register(struct clk *clk); +void clk_unregister(struct clk *clk); + +/* ----- */ + +#define MAINDIV1(c) (((c) >> 7) & 0x0f) +#define MAINDIV2(c) (((c) >> 11) & 0x1f) +#define PS(c) (((c) >> 18) & 0x03) +#define PREDIV(c) (((c) >> 2) & 0x1f) +#define HCLKDIV(c) (((c) >> 0) & 0x02) +#define PCLKDIV(c) (((c) >> 16) & 0x03) + +unsigned int cpufreq_get (unsigned int cpu) /* in kHz */ +{ + return fclkfreq_get ()/1000; +} +EXPORT_SYMBOL(cpufreq_get); + +unsigned int fclkfreq_get (void) +{ + unsigned int clkset = CSC_CLKSET; + unsigned int gclk + = XTAL_IN + / (1 << PS(clkset)) + * (MAINDIV1(clkset) + 2) + / (PREDIV(clkset) + 2) + * (MAINDIV2(clkset) + 2) + ; + return gclk; +} + +unsigned int hclkfreq_get (void) +{ + unsigned int clkset = CSC_CLKSET; + unsigned int hclk = fclkfreq_get () / (HCLKDIV(clkset) + 1); + + return hclk; +} + +unsigned int pclkfreq_get (void) +{ + unsigned int clkset = CSC_CLKSET; + int pclkdiv = PCLKDIV(clkset); + unsigned int pclk; + if (pclkdiv == 0x3) + pclkdiv = 0x2; + pclk = hclkfreq_get () / (1 << pclkdiv); + + return pclk; +} + +/* ----- */ + +static LIST_HEAD(clocks); +static DECLARE_MUTEX(clocks_sem); + +struct clk *clk_get (struct device *dev, const char *id) +{ + struct clk *p; + struct clk *clk = ERR_PTR(-ENOENT); + + down (&clocks_sem); + list_for_each_entry (p, &clocks, node) { + if (strcmp (id, p->name) == 0 + && try_module_get(p->owner)) { + clk = p; + break; + } + } + up (&clocks_sem); + + return clk; +} +EXPORT_SYMBOL(clk_get); + +void clk_put (struct clk *clk) +{ + module_put(clk->owner); +} +EXPORT_SYMBOL(clk_put); + +int clk_enable (struct clk *clk) +{ + return 0; +} +EXPORT_SYMBOL(clk_enable); + +void clk_disable (struct clk *clk) +{ +} +EXPORT_SYMBOL(clk_disable); + +int clk_use (struct clk *clk) +{ + return 0; +} +EXPORT_SYMBOL(clk_use); + +void clk_unuse (struct clk *clk) +{ +} +EXPORT_SYMBOL(clk_unuse); + +unsigned long clk_get_rate (struct clk *clk) +{ + return clk->rate; +} +EXPORT_SYMBOL(clk_get_rate); + +long clk_round_rate (struct clk *clk, unsigned long rate) +{ + return rate; +} +EXPORT_SYMBOL(clk_round_rate); + +int clk_set_rate (struct clk *clk, unsigned long rate) +{ + int ret = -EIO; + return ret; +} +EXPORT_SYMBOL(clk_set_rate); + +#if 0 +/* + * These are fixed clocks. + */ +static struct clk kmi_clk = { + .name = "KMIREFCLK", + .rate = 24000000, +}; + +static struct clk uart_clk = { + .name = "UARTCLK", + .rate = 24000000, +}; + +static struct clk mmci_clk = { + .name = "MCLK", + .rate = 33000000, +}; +#endif + +static struct clk clcd_clk = { + .name = "CLCDCLK", + .rate = 0, +}; + +int clk_register (struct clk *clk) +{ + down (&clocks_sem); + list_add (&clk->node, &clocks); + up (&clocks_sem); + return 0; +} +EXPORT_SYMBOL(clk_register); + +void clk_unregister (struct clk *clk) +{ + down (&clocks_sem); + list_del (&clk->node); + up (&clocks_sem); +} +EXPORT_SYMBOL(clk_unregister); + +static int __init clk_init (void) +{ + clk_register(&clcd_clk); + return 0; +} +arch_initcall(clk_init); diff --git a/arch/arm/mach-lh7a40x/common.h b/arch/arm/mach-lh7a40x/common.h index ea8de7e3ab1..18e8bb4eb20 100644 --- a/arch/arm/mach-lh7a40x/common.h +++ b/arch/arm/mach-lh7a40x/common.h @@ -12,6 +12,7 @@ extern struct sys_timer lh7a40x_timer; extern void lh7a400_init_irq (void); extern void lh7a404_init_irq (void); +extern void lh7a40x_clcd_init (void); extern void lh7a40x_init_board_irq (void); #define IRQ_DISPATCH(irq) desc_handle_irq((irq),(irq_desc + irq), regs) diff --git a/arch/arm/mach-lh7a40x/irq-lh7a404.c b/arch/arm/mach-lh7a40x/irq-lh7a404.c index e902e3d87da..2685a81454d 100644 --- a/arch/arm/mach-lh7a40x/irq-lh7a404.c +++ b/arch/arm/mach-lh7a40x/irq-lh7a404.c @@ -28,13 +28,17 @@ static unsigned char irq_pri_vic1[] = { #if defined (USE_PRIORITIES) -IRQ_GPIO3INTR, + IRQ_GPIO3INTR, /* CPLD */ + IRQ_DMAM2P4, IRQ_DMAM2P5, /* AC97 */ #endif }; static unsigned char irq_pri_vic2[] = { #if defined (USE_PRIORITIES) - IRQ_T3UI, IRQ_GPIO7INTR, + IRQ_T3UI, /* Timer */ + IRQ_GPIO7INTR, /* CPLD */ IRQ_UART1INTR, IRQ_UART2INTR, IRQ_UART3INTR, + IRQ_LCDINTR, /* LCD */ + IRQ_TSCINTR, /* ADC/Touchscreen */ #endif }; @@ -98,10 +102,19 @@ static struct irqchip lh7a404_gpio_vic2_chip = { /* IRQ initialization */ +#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404) +extern void* branch_irq_lh7a400; +#endif + void __init lh7a404_init_irq (void) { int irq; +#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404) +#define NOP 0xe1a00000 /* mov r0, r0 */ + branch_irq_lh7a400 = NOP; +#endif + VIC1_INTENCLR = 0xffffffff; VIC2_INTENCLR = 0xffffffff; VIC1_INTSEL = 0; /* All IRQs */ diff --git a/arch/arm/mach-lh7a40x/lcd-panel.h b/arch/arm/mach-lh7a40x/lcd-panel.h new file mode 100644 index 00000000000..4fb2efc4950 --- /dev/null +++ b/arch/arm/mach-lh7a40x/lcd-panel.h @@ -0,0 +1,346 @@ +/* lcd-panel.h + $Id$ + + written by Marc Singer + 18 Jul 2005 + + Copyright (C) 2005 Marc Singer + + ----------- + DESCRIPTION + ----------- + + Only one panel may be defined at a time. + + The pixel clock is calculated to be no greater than the target. + + Each timing value is accompanied by a specification comment. + + UNITS/MIN/TYP/MAX + + Most of the units will be in clocks. + + USE_RGB555 + + Define this macro to configure the AMBA LCD controller to use an + RGB555 encoding for the pels instead of the normal RGB565. + + LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11 + + These boards are best approximated by 555 for all panels. Some + can use an extra low-order bit of blue in bit 16 of the color + value, but we don't have a way to communicate this non-linear + mapping to the kernel. + +*/ + +#if !defined (__LCD_PANEL_H__) +# define __LCD_PANEL_H__ + +#if defined (MACH_LPD79520)\ + || defined (MACH_LPD79524)\ + || defined (MACH_LPD7A400)\ + || defined (MACH_LPD7A404) +# define USE_RGB555 +#endif + +struct clcd_panel_extra { + unsigned int hrmode; + unsigned int clsen; + unsigned int spsen; + unsigned int pcdel; + unsigned int revdel; + unsigned int lpdel; + unsigned int spldel; + unsigned int pc2del; +}; + +#define NS_TO_CLOCK(ns,c) ((((ns)*((c)/1000) + (1000000 - 1))/1000000)) +#define CLOCK_TO_DIV(e,c) (((c) + (e) - 1)/(e)) + +#if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT + + /* Logic Product Development LCD 3.5" QVGA HRTFT -10 */ + /* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */ + +#define PIX_CLOCK_TARGET (6800000) +#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) +#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) + +static struct clcd_panel lcd_panel = { + .mode = { + .name = "3.5in QVGA (LQ035Q7DB02)", + .xres = 240, + .yres = 320, + .pixclock = PIX_CLOCK, + .left_margin = 16, + .right_margin = 21, + .upper_margin = 8, // line/8/8/8 + .lower_margin = 5, + .hsync_len = 61, + .vsync_len = NS_TO_CLOCK (60, PIX_CLOCK), + .vmode = FB_VMODE_NONINTERLACED, + }, + .width = -1, + .height = -1, + .tim2 = TIM2_IPC | (PIX_CLOCK_DIVIDER - 2), + .cntl = CNTL_LCDTFT | CNTL_WATERMARK, + .bpp = 16, +}; + +#define HAS_LCD_PANEL_EXTRA + +static struct clcd_panel_extra lcd_panel_extra = { + .hrmode = 1, + .clsen = 1, + .spsen = 1, + .pcdel = 8, + .revdel = 7, + .lpdel = 13, + .spldel = 77, + .pc2del = 208, +}; + +#endif + +#if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02 + + /* Logic Product Development LCD 5.7" QVGA -10 */ + /* Sharp PN LQ057Q3DC02 */ + /* QVGA mode, V/Q=LOW */ + +/* From Sharp on 2006.1.3. I believe some of the values are incorrect + * based on the datasheet. + + Timing0 TIMING1 TIMING2 CONTROL + 0x140A0C4C 0x080504EF 0x013F380D 0x00000829 + HBP= 20 VBP= 8 BCD= 0 + HFP= 10 VFP= 5 CPL=319 + HSW= 12 VSW= 1 IOE= 0 + PPL= 19 LPP=239 IPC= 1 + IHS= 1 + IVS= 1 + ACB= 0 + CSEL= 0 + PCD= 13 + + */ + +/* The full horozontal cycle (Th) is clock/360/400/450. */ +/* The full vertical cycle (Tv) is line/251/262/280. */ + +#define PIX_CLOCK_TARGET (6300000) /* -/6.3/7 MHz */ +#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) +#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) + +static struct clcd_panel lcd_panel = { + .mode = { + .name = "5.7in QVGA (LQ057Q3DC02)", + .xres = 320, + .yres = 240, + .pixclock = PIX_CLOCK, + .left_margin = 11, + .right_margin = 400-11-320-2, + .upper_margin = 7, // line/7/7/7 + .lower_margin = 262-7-240-2, + .hsync_len = 2, // clk/2/96/200 + .vsync_len = 2, // line/2/-/34 + .vmode = FB_VMODE_NONINTERLACED, + }, + .width = -1, + .height = -1, + .tim2 = TIM2_IHS | TIM2_IVS + | (PIX_CLOCK_DIVIDER - 2), + .cntl = CNTL_LCDTFT | CNTL_WATERMARK, + .bpp = 16, +}; + +#endif + +#if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343 + + /* Logic Product Development LCD 6.4" VGA -10 */ + /* Sharp PN LQ64D343 */ + +/* The full horozontal cycle (Th) is clock/750/800/900. */ +/* The full vertical cycle (Tv) is line/515/525/560. */ + +#define PIX_CLOCK_TARGET (28330000) +#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) +#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) + +static struct clcd_panel lcd_panel = { + .mode = { + .name = "6.4in QVGA (LQ64D343)", + .xres = 640, + .yres = 480, + .pixclock = PIX_CLOCK, + .left_margin = 32, + .right_margin = 800-32-640-96, + .upper_margin = 32, // line/34/34/34 + .lower_margin = 540-32-480-2, + .hsync_len = 96, // clk/2/96/200 + .vsync_len = 2, // line/2/-/34 + .vmode = FB_VMODE_NONINTERLACED, + }, + .width = -1, + .height = -1, + .tim2 = TIM2_IHS | TIM2_IVS + | (PIX_CLOCK_DIVIDER - 2), + .cntl = CNTL_LCDTFT | CNTL_WATERMARK, + .bpp = 16, +}; + +#endif + +#if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368 + + /* Logic Product Development LCD 10.4" VGA -10 */ + /* Sharp PN LQ10D368 */ + +#define PIX_CLOCK_TARGET (28330000) +#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) +#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) + +static struct clcd_panel lcd_panel = { + .mode = { + .name = "10.4in VGA (LQ10D368)", + .xres = 640, + .yres = 480, + .pixclock = PIX_CLOCK, + .left_margin = 21, + .right_margin = 15, + .upper_margin = 34, + .lower_margin = 5, + .hsync_len = 96, + .vsync_len = 16, + .vmode = FB_VMODE_NONINTERLACED, + }, + .width = -1, + .height = -1, + .tim2 = TIM2_IHS | TIM2_IVS + | (PIX_CLOCK_DIVIDER - 2), + .cntl = CNTL_LCDTFT | CNTL_WATERMARK, + .bpp = 16, +}; + +#endif + +#if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41 + + /* Logic Product Development LCD 12.1" SVGA -10 */ + /* Sharp PN LQ121S1DG41, was LQ121S1DG31 */ + +/* Note that with a 99993900 Hz HCLK, it is not possible to hit the + * target clock frequency range of 35MHz to 42MHz. */ + +/* If the target pixel clock is substantially lower than the panel + * spec, this is done to prevent the LCD display from glitching when + * the CPU is under load. A pixel clock higher than 25MHz + * (empirically determined) will compete with the CPU for bus cycles + * for the Ethernet chip. However, even a pixel clock of 10MHz + * competes with Compact Flash interface during some operations + * (fdisk, e2fsck). And, at that speed the display may have a visible + * flicker. */ + +/* The full horozontal cycle (Th) is clock/832/1056/1395. */ + +#define PIX_CLOCK_TARGET (20000000) +#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) +#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) + +static struct clcd_panel lcd_panel = { + .mode = { + .name = "12.1in SVGA (LQ121S1DG41)", + .xres = 800, + .yres = 600, + .pixclock = PIX_CLOCK, + .left_margin = 89, // ns/5/-/(1/PIX_CLOCK)-10 + .right_margin = 1056-800-89-128, + .upper_margin = 23, // line/23/23/23 + .lower_margin = 44, + .hsync_len = 128, // clk/2/128/200 + .vsync_len = 4, // line/2/4/6 + .vmode = FB_VMODE_NONINTERLACED, + }, + .width = -1, + .height = -1, + .tim2 = TIM2_IHS | TIM2_IVS + | (PIX_CLOCK_DIVIDER - 2), + .cntl = CNTL_LCDTFT | CNTL_WATERMARK, + .bpp = 16, +}; + +#endif + +#if defined CONFIG_FB_ARMCLCD_HITACHI + + /* Hitachi*/ + /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */ + +#define PIX_CLOCK_TARGET (49000000) +#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) +#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) + +static struct clcd_panel lcd_panel = { + .mode = { + .name = "Hitachi 800x480", + .xres = 800, + .yres = 480, + .pixclock = PIX_CLOCK, + .left_margin = 88, + .right_margin = 40, + .upper_margin = 32, + .lower_margin = 11, + .hsync_len = 128, + .vsync_len = 2, + .vmode = FB_VMODE_NONINTERLACED, + }, + .width = -1, + .height = -1, + .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS + | (PIX_CLOCK_DIVIDER - 2), + .cntl = CNTL_LCDTFT | CNTL_WATERMARK, + .bpp = 16, +}; + +#endif + + +#if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE + + /* AU Optotronics A070VW01 7.0 Wide Screen color Display*/ + /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */ + +#define PIX_CLOCK_TARGET (10000000) +#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK) +#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER) + +static struct clcd_panel lcd_panel = { + .mode = { + .name = "7.0in Wide (A070VW01)", + .xres = 480, + .yres = 234, + .pixclock = PIX_CLOCK, + .left_margin = 30, + .right_margin = 25, + .upper_margin = 14, + .lower_margin = 12, + .hsync_len = 100, + .vsync_len = 1, + .vmode = FB_VMODE_NONINTERLACED, + }, + .width = -1, + .height = -1, + .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS + | (PIX_CLOCK_DIVIDER - 2), + .cntl = CNTL_LCDTFT | CNTL_WATERMARK, + .bpp = 16, +}; + +#endif + +#undef NS_TO_CLOCK +#undef CLOCK_TO_DIV + +#endif /* __LCD_PANEL_H__ */ diff --git a/arch/arm/mach-lh7a40x/ssp-cpld.c b/arch/arm/mach-lh7a40x/ssp-cpld.c new file mode 100644 index 00000000000..a10830186da --- /dev/null +++ b/arch/arm/mach-lh7a40x/ssp-cpld.c @@ -0,0 +1,343 @@ +/* arch/arm/mach-lh7a40x/ssp-cpld.c + * + * Copyright (C) 2004,2005 Marc Singer + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * SSP/SPI driver for the CardEngine CPLD. + * + */ + +/* NOTES + ----- + + o *** This driver is cribbed from the 7952x implementation. + Some comments may not apply. + + o This driver contains sufficient logic to control either the + serial EEPROMs or the audio codec. It is included in the kernel + to support the codec. The EEPROMs are really the responsibility + of the boot loader and should probably be left alone. + + o The code must be augmented to cope with multiple, simultaneous + clients. + o The audio codec writes to the codec chip whenever playback + starts. + o The touchscreen driver writes to the ads chip every time it + samples. + o The audio codec must write 16 bits, but the touch chip writes + are 8 bits long. + o We need to be able to keep these configurations separate while + simultaneously active. + + */ + +#include <linux/module.h> +#include <linux/kernel.h> +//#include <linux/sched.h> +#include <linux/errno.h> +#include <linux/interrupt.h> +//#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/spinlock.h> + +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/hardware.h> + +#include <asm/arch/ssp.h> + +//#define TALK + +#if defined (TALK) +#define PRINTK(f...) printk (f) +#else +#define PRINTK(f...) do {} while (0) +#endif + +#if defined (CONFIG_ARCH_LH7A400) +# define CPLD_SPID __REGP16(CPLD06_VIRT) /* SPI data */ +# define CPLD_SPIC __REGP16(CPLD08_VIRT) /* SPI control */ +# define CPLD_SPIC_CS_CODEC (1<<0) +# define CPLD_SPIC_CS_TOUCH (1<<1) +# define CPLD_SPIC_WRITE (0<<2) +# define CPLD_SPIC_READ (1<<2) +# define CPLD_SPIC_DONE (1<<3) /* r/o */ +# define CPLD_SPIC_LOAD (1<<4) +# define CPLD_SPIC_START (1<<4) +# define CPLD_SPIC_LOADED (1<<5) /* r/o */ +#endif + +#define CPLD_SPI __REGP16(CPLD0A_VIRT) /* SPI operation */ +#define CPLD_SPI_CS_EEPROM (1<<3) +#define CPLD_SPI_SCLK (1<<2) +#define CPLD_SPI_TX_SHIFT (1) +#define CPLD_SPI_TX (1<<CPLD_SPI_TX_SHIFT) +#define CPLD_SPI_RX_SHIFT (0) +#define CPLD_SPI_RX (1<<CPLD_SPI_RX_SHIFT) + +/* *** FIXME: these timing values are substantially larger than the + *** chip requires. We may implement an nsleep () function. */ +#define T_SKH 1 /* Clock time high (us) */ +#define T_SKL 1 /* Clock time low (us) */ +#define T_CS 1 /* Minimum chip select low time (us) */ +#define T_CSS 1 /* Minimum chip select setup time (us) */ +#define T_DIS 1 /* Data setup time (us) */ + + /* EEPROM SPI bits */ +#define P_START (1<<9) +#define P_WRITE (1<<7) +#define P_READ (2<<7) +#define P_ERASE (3<<7) +#define P_EWDS (0<<7) +#define P_WRAL (0<<7) +#define P_ERAL (0<<7) +#define P_EWEN (0<<7) +#define P_A_EWDS (0<<5) +#define P_A_WRAL (1<<5) +#define P_A_ERAL (2<<5) +#define P_A_EWEN (3<<5) + +struct ssp_configuration { + int device; + int mode; + int speed; + int frame_size_write; + int frame_size_read; +}; + +static struct ssp_configuration ssp_configuration; +static spinlock_t ssp_lock; + +static void enable_cs (void) +{ + switch (ssp_configuration.device) { + case DEVICE_EEPROM: + CPLD_SPI |= CPLD_SPI_CS_EEPROM; + break; + } + udelay (T_CSS); +} + +static void disable_cs (void) +{ + switch (ssp_configuration.device) { + case DEVICE_EEPROM: + CPLD_SPI &= ~CPLD_SPI_CS_EEPROM; + break; + } + udelay (T_CS); +} + +static void pulse_clock (void) +{ + CPLD_SPI |= CPLD_SPI_SCLK; + udelay (T_SKH); + CPLD_SPI &= ~CPLD_SPI_SCLK; + udelay (T_SKL); +} + + +/* execute_spi_command + + sends an spi command to a device. It first sends cwrite bits from + v. If cread is greater than zero it will read cread bits + (discarding the leading 0 bit) and return them. If cread is less + than zero it will check for completetion status and return 0 on + success or -1 on timeout. If cread is zero it does nothing other + than sending the command. + + On the LPD7A400, we can only read or write multiples of 8 bits on + the codec and the touch screen device. Here, we round up. + +*/ + +static int execute_spi_command (int v, int cwrite, int cread) +{ + unsigned long l = 0; + +#if defined (CONFIG_MACH_LPD7A400) + /* The codec and touch devices cannot be bit-banged. Instead, + * the CPLD provides an eight-bit shift register and a crude + * interface. */ + if ( ssp_configuration.device == DEVICE_CODEC + || ssp_configuration.device == DEVICE_TOUCH) { + int select = 0; + + PRINTK ("spi(%d %d.%d) 0x%04x", + ssp_configuration.device, cwrite, cread, + v); +#if defined (TALK) + if (ssp_configuration.device == DEVICE_CODEC) + PRINTK (" 0x%03x -> %2d", v & 0x1ff, (v >> 9) & 0x7f); +#endif + PRINTK ("\n"); + + if (ssp_configuration.device == DEVICE_CODEC) + select = CPLD_SPIC_CS_CODEC; + if (ssp_configuration.device == DEVICE_TOUCH) + select = CPLD_SPIC_CS_TOUCH; + if (cwrite) { + for (cwrite = (cwrite + 7)/8; cwrite-- > 0; ) { + CPLD_SPID = (v >> (8*cwrite)) & 0xff; + CPLD_SPIC = select | CPLD_SPIC_LOAD; + while (!(CPLD_SPIC & CPLD_SPIC_LOADED)) + ; + CPLD_SPIC = select; + while (!(CPLD_SPIC & CPLD_SPIC_DONE)) + ; + } + v = 0; + } + if (cread) { + mdelay (2); /* *** FIXME: required by ads7843? */ + v = 0; + for (cread = (cread + 7)/8; cread-- > 0;) { + CPLD_SPID = 0; + CPLD_SPIC = select | CPLD_SPIC_READ + | CPLD_SPIC_START; + while (!(CPLD_SPIC & CPLD_SPIC_LOADED)) + ; + CPLD_SPIC = select | CPLD_SPIC_READ; + while (!(CPLD_SPIC & CPLD_SPIC_DONE)) + ; + v = (v << 8) | CPLD_SPID; + } + } + return v; + } +#endif + + PRINTK ("spi(%d) 0x%04x -> 0x%x\r\n", ssp_configuration.device, + v & 0x1ff, (v >> 9) & 0x7f); + + enable_cs (); + + v <<= CPLD_SPI_TX_SHIFT; /* Correction for position of SPI_TX bit */ + while (cwrite--) { + CPLD_SPI + = (CPLD_SPI & ~CPLD_SPI_TX) + | ((v >> cwrite) & CPLD_SPI_TX); + udelay (T_DIS); + pulse_clock (); + } + + if (cread < 0) { + int delay = 10; + disable_cs (); + udelay (1); + enable_cs (); + + l = -1; + do { + if (CPLD_SPI & CPLD_SPI_RX) { + l = 0; + break; + } + } while (udelay (1), --delay); + } + else + /* We pulse the clock before the data to skip the leading zero. */ + while (cread-- > 0) { + pulse_clock (); + l = (l<<1) + | (((CPLD_SPI & CPLD_SPI_RX) + >> CPLD_SPI_RX_SHIFT) & 0x1); + } + + disable_cs (); + return l; +} + +static int ssp_init (void) +{ + spin_lock_init (&ssp_lock); + memset (&ssp_configuration, 0, sizeof (ssp_configuration)); + return 0; +} + + +/* ssp_chip_select + + drops the chip select line for the CPLD shift-register controlled + devices. It doesn't enable chip + +*/ + +static void ssp_chip_select (int enable) +{ +#if defined (CONFIG_MACH_LPD7A400) + int select; + + if (ssp_configuration.device == DEVICE_CODEC) + select = CPLD_SPIC_CS_CODEC; + else if (ssp_configuration.device == DEVICE_TOUCH) + select = CPLD_SPIC_CS_TOUCH; + else + return; + + if (enable) + CPLD_SPIC = select; + else + CPLD_SPIC = 0; +#endif +} + +static void ssp_acquire (void) +{ + spin_lock (&ssp_lock); +} + +static void ssp_release (void) +{ + ssp_chip_select (0); /* just in case */ + spin_unlock (&ssp_lock); +} + +static int ssp_configure (int device, int mode, int speed, + int frame_size_write, int frame_size_read) +{ + ssp_configuration.device = device; + ssp_configuration.mode = mode; + ssp_configuration.speed = speed; + ssp_configuration.frame_size_write = frame_size_write; + ssp_configuration.frame_size_read = frame_size_read; + + return 0; +} + +static int ssp_read (void) +{ + return execute_spi_command (0, 0, ssp_configuration.frame_size_read); +} + +static int ssp_write (u16 data) +{ + execute_spi_command (data, ssp_configuration.frame_size_write, 0); + return 0; +} + +static int ssp_write_read (u16 data) +{ + return execute_spi_command (data, ssp_configuration.frame_size_write, + ssp_configuration.frame_size_read); +} + +struct ssp_driver lh7a40x_cpld_ssp_driver = { + .init = ssp_init, + .acquire = ssp_acquire, + .release = ssp_release, + .configure = ssp_configure, + .chip_select = ssp_chip_select, + .read = ssp_read, + .write = ssp_write, + .write_read = ssp_write_read, +}; + + +MODULE_AUTHOR("Marc Singer"); +MODULE_DESCRIPTION("LPD7A40X CPLD SPI driver"); +MODULE_LICENSE("GPL"); diff --git a/arch/arm/mach-lh7a40x/time.c b/arch/arm/mach-lh7a40x/time.c index be377e331f2..ef9af375fcc 100644 --- a/arch/arm/mach-lh7a40x/time.c +++ b/arch/arm/mach-lh7a40x/time.c @@ -1,4 +1,4 @@ -/* +/* * arch/arm/mach-lh7a40x/time.c * * Copyright (C) 2004 Logic Product Development @@ -57,7 +57,7 @@ static struct irqaction lh7a40x_timer_irq = { .handler = lh7a40x_timer_interrupt, }; -static void __init lh7a40x_timer_init(void) +static void __init lh7a40x_timer_init (void) { /* Stop/disable all timers */ TIMER_CONTROL1 = 0; diff --git a/arch/arm/mach-pnx4008/Makefile b/arch/arm/mach-pnx4008/Makefile new file mode 100644 index 00000000000..b457ca0a431 --- /dev/null +++ b/arch/arm/mach-pnx4008/Makefile @@ -0,0 +1,12 @@ +# +# Makefile for the linux kernel. +# + +obj-y := core.o irq.o time.o clock.o gpio.o serial.o dma.o +obj-m := +obj-n := +obj- := + +# Power Management +obj-$(CONFIG_PM) += pm.o sleep.o + diff --git a/arch/arm/mach-pnx4008/Makefile.boot b/arch/arm/mach-pnx4008/Makefile.boot new file mode 100644 index 00000000000..44c7117e20d --- /dev/null +++ b/arch/arm/mach-pnx4008/Makefile.boot @@ -0,0 +1,4 @@ + zreladdr-y := 0x80008000 +params_phys-y := 0x80000100 +initrd_phys-y := 0x80800000 + diff --git a/arch/arm/mach-pnx4008/clock.c b/arch/arm/mach-pnx4008/clock.c new file mode 100644 index 00000000000..285b22f631e --- /dev/null +++ b/arch/arm/mach-pnx4008/clock.c @@ -0,0 +1,1010 @@ +/* + * arch/arm/mach-pnx4008/clock.c + * + * Clock control driver for PNX4008 + * + * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com> + * Generic clock management functions are partially based on: + * linux/arch/arm/mach-omap/clock.c + * + * 2005-2006 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/errno.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/delay.h> + +#include <asm/semaphore.h> +#include <asm/hardware.h> +#include <asm/io.h> + +#include <asm/arch/clock.h> +#include "clock.h" + +/*forward declaration*/ +static struct clk per_ck; +static struct clk hclk_ck; +static struct clk ck_1MHz; +static struct clk ck_13MHz; +static struct clk ck_pll1; +static int local_set_rate(struct clk *clk, u32 rate); + +static inline void clock_lock(void) +{ + local_irq_disable(); +} + +static inline void clock_unlock(void) +{ + local_irq_enable(); +} + +static void propagate_rate(struct clk *clk) +{ + struct clk *tmp_clk; + + tmp_clk = clk; + while (tmp_clk->propagate_next) { + tmp_clk = tmp_clk->propagate_next; + local_set_rate(tmp_clk, tmp_clk->user_rate); + } +} + +static inline void clk_reg_disable(struct clk *clk) +{ + if (clk->enable_reg) + __raw_writel(__raw_readl(clk->enable_reg) & + ~(1 << clk->enable_shift), clk->enable_reg); +} + +static inline void clk_reg_enable(struct clk *clk) +{ + if (clk->enable_reg) + __raw_writel(__raw_readl(clk->enable_reg) | + (1 << clk->enable_shift), clk->enable_reg); +} + +static inline void clk_reg_disable1(struct clk *clk) +{ + if (clk->enable_reg1) + __raw_writel(__raw_readl(clk->enable_reg1) & + ~(1 << clk->enable_shift1), clk->enable_reg1); +} + +static inline void clk_reg_enable1(struct clk *clk) +{ + if (clk->enable_reg1) + __raw_writel(__raw_readl(clk->enable_reg1) | + (1 << clk->enable_shift1), clk->enable_reg1); +} + +static int clk_wait_for_pll_lock(struct clk *clk) +{ + int i; + i = 0; + while (i++ < 0xFFF && !(__raw_readl(clk->scale_reg) & 1)) ; /*wait for PLL to lock */ + + if (!(__raw_readl(clk->scale_reg) & 1)) { + printk(KERN_ERR + "%s ERROR: failed to lock, scale reg data: %x\n", + clk->name, __raw_readl(clk->scale_reg)); + return -1; + } + return 0; +} + +static int switch_to_dirty_13mhz(struct clk *clk) +{ + int i; + int ret; + u32 tmp_reg; + + ret = 0; + + if (!clk->rate) + clk_reg_enable1(clk); + + tmp_reg = __raw_readl(clk->parent_switch_reg); + /*if 13Mhz clock selected, select 13'MHz (dirty) source from OSC */ + if (!(tmp_reg & 1)) { + tmp_reg |= (1 << 1); /* Trigger switch to 13'MHz (dirty) clock */ + __raw_writel(tmp_reg, clk->parent_switch_reg); + i = 0; + while (i++ < 0xFFF && !(__raw_readl(clk->parent_switch_reg) & 1)) ; /*wait for 13'MHz selection status */ + + if (!(__raw_readl(clk->parent_switch_reg) & 1)) { + printk(KERN_ERR + "%s ERROR: failed to select 13'MHz, parent sw reg data: %x\n", + clk->name, __raw_readl(clk->parent_switch_reg)); + ret = -1; + } + } + + if (!clk->rate) + clk_reg_disable1(clk); + + return ret; +} + +static int switch_to_clean_13mhz(struct clk *clk) +{ + int i; + int ret; + u32 tmp_reg; + + ret = 0; + + if (!clk->rate) + clk_reg_enable1(clk); + + tmp_reg = __raw_readl(clk->parent_switch_reg); + /*if 13'Mhz clock selected, select 13MHz (clean) source from OSC */ + if (tmp_reg & 1) { + tmp_reg &= ~(1 << 1); /* Trigger switch to 13MHz (clean) clock */ + __raw_writel(tmp_reg, clk->parent_switch_reg); + i = 0; + while (i++ < 0xFFF && (__raw_readl(clk->parent_switch_reg) & 1)) ; /*wait for 13MHz selection status */ + + if (__raw_readl(clk->parent_switch_reg) & 1) { + printk(KERN_ERR + "%s ERROR: failed to select 13MHz, parent sw reg data: %x\n", + clk->name, __raw_readl(clk->parent_switch_reg)); + ret = -1; + } + } + + if (!clk->rate) + clk_reg_disable1(clk); + + return ret; +} + +static int set_13MHz_parent(struct clk *clk, struct clk *parent) +{ + int ret = -EINVAL; + + if (parent == &ck_13MHz) + ret = switch_to_clean_13mhz(clk); + else if (parent == &ck_pll1) + ret = switch_to_dirty_13mhz(clk); + + return ret; +} + +#define PLL160_MIN_FCCO 156000 +#define PLL160_MAX_FCCO 320000 + +/* + * Calculate pll160 settings. + * Possible input: up to 320MHz with step of clk->parent->rate. + * In PNX4008 parent rate for pll160s may be either 1 or 13MHz. + * Ignored paths: "feedback" (bit 13 set), "div-by-N". + * Setting ARM PLL4 rate to 0 will put CPU into direct run mode. + * Setting PLL5 and PLL3 rate to 0 will disable USB and DSP clock input. + * Please refer to PNX4008 IC manual for details. + */ + +static int pll160_set_rate(struct clk *clk, u32 rate) +{ + u32 tmp_reg, tmp_m, tmp_2p, i; + u32 parent_rate; + int ret = -EINVAL; + + parent_rate = clk->parent->rate; + + if (!parent_rate) + goto out; + + /* set direct run for ARM or disable output for others */ + clk_reg_disable(clk); + + /* disable source input as well (ignored for ARM) */ + clk_reg_disable1(clk); + + tmp_reg = __raw_readl(clk->scale_reg); + tmp_reg &= ~0x1ffff; /*clear all settings, power down */ + __raw_writel(tmp_reg, clk->scale_reg); + + rate -= rate % parent_rate; /*round down the input */ + + if (rate > PLL160_MAX_FCCO) + rate = PLL160_MAX_FCCO; + + if (!rate) { + clk->rate = 0; + ret = 0; + goto out; + } + + clk_reg_enable1(clk); + tmp_reg = __raw_readl(clk->scale_reg); + + if (rate == parent_rate) { + /*enter direct bypass mode */ + tmp_reg |= ((1 << 14) | (1 << 15)); + __raw_writel(tmp_reg, clk->scale_reg); + clk->rate = parent_rate; + clk_reg_enable(clk); + ret = 0; + goto out; + } + + i = 0; + for (tmp_2p = 1; tmp_2p < 16; tmp_2p <<= 1) { + if (rate * tmp_2p >= PLL160_MIN_FCCO) + break; + i++; + } + + if (tmp_2p > 1) + tmp_reg |= ((i - 1) << 11); + else + tmp_reg |= (1 << 14); /*direct mode, no divide */ + + tmp_m = rate * tmp_2p; + tmp_m /= parent_rate; + + tmp_reg |= (tmp_m - 1) << 1; /*calculate M */ + tmp_reg |= (1 << 16); /*power up PLL */ + __raw_writel(tmp_reg, clk->scale_reg); + + if (clk_wait_for_pll_lock(clk) < 0) { + clk_reg_disable(clk); + clk_reg_disable1(clk); + + tmp_reg = __raw_readl(clk->scale_reg); + tmp_reg &= ~0x1ffff; /*clear all settings, power down */ + __raw_writel(tmp_reg, clk->scale_reg); + clk->rate = 0; + ret = -EFAULT; + goto out; + } + + clk->rate = (tmp_m * parent_rate) / tmp_2p; + + if (clk->flags & RATE_PROPAGATES) + propagate_rate(clk); + + clk_reg_enable(clk); + ret = 0; + +out: + return ret; +} + +/*configure PER_CLK*/ +static int per_clk_set_rate(struct clk *clk, u32 rate) +{ + u32 tmp; + + tmp = __raw_readl(clk->scale_reg); + tmp &= ~(0x1f << 2); + tmp |= ((clk->parent->rate / clk->rate) - 1) << 2; + __raw_writel(tmp, clk->scale_reg); + clk->rate = rate; + return 0; +} + +/*configure HCLK*/ +static int hclk_set_rate(struct clk *clk, u32 rate) +{ + u32 tmp; + tmp = __raw_readl(clk->scale_reg); + tmp = tmp & ~0x3; + switch (rate) { + case 1: + break; + case 2: + tmp |= 1; + break; + case 4: + tmp |= 2; + break; + } + + __raw_writel(tmp, clk->scale_reg); + clk->rate = rate; + return 0; +} + +static u32 hclk_round_rate(struct clk *clk, u32 rate) +{ + switch (rate) { + case 1: + case 4: + return rate; + } + return 2; +} + +static u32 per_clk_round_rate(struct clk *clk, u32 rate) +{ + return CLK_RATE_13MHZ; +} + +static int on_off_set_rate(struct clk *clk, u32 rate) +{ + if (rate) { + clk_reg_enable(clk); + clk->rate = 1; + } else { + clk_reg_disable(clk); + clk->rate = 0; + } + return 0; +} + +static int on_off_inv_set_rate(struct clk *clk, u32 rate) +{ + if (rate) { + clk_reg_disable(clk); /*enable bit is inverted */ + clk->rate = 1; + } else { + clk_reg_enable(clk); + clk->rate = 0; + } + return 0; +} + +static u32 on_off_round_rate(struct clk *clk, u32 rate) +{ + return (rate ? 1 : 0); +} + +static u32 pll4_round_rate(struct clk *clk, u32 rate) +{ + if (rate > CLK_RATE_208MHZ) + rate = CLK_RATE_208MHZ; + if (rate == CLK_RATE_208MHZ && hclk_ck.user_rate == 1) + rate = CLK_RATE_208MHZ - CLK_RATE_13MHZ; + return (rate - (rate % (hclk_ck.user_rate * CLK_RATE_13MHZ))); +} + +static u32 pll3_round_rate(struct clk *clk, u32 rate) +{ + if (rate > CLK_RATE_208MHZ) + rate = CLK_RATE_208MHZ; + return (rate - rate % CLK_RATE_13MHZ); +} + +static u32 pll5_round_rate(struct clk *clk, u32 rate) +{ + return (rate ? CLK_RATE_48MHZ : 0); +} + +static u32 ck_13MHz_round_rate(struct clk *clk, u32 rate) +{ + return (rate ? CLK_RATE_13MHZ : 0); +} + +static int ck_13MHz_set_rate(struct clk *clk, u32 rate) +{ + if (rate) { + clk_reg_disable(clk); /*enable bit is inverted */ + udelay(500); + clk->rate = CLK_RATE_13MHZ; + ck_1MHz.rate = CLK_RATE_1MHZ; + } else { + clk_reg_enable(clk); + clk->rate = 0; + ck_1MHz.rate = 0; + } + return 0; +} + +static int pll1_set_rate(struct clk *clk, u32 rate) +{ +#if 0 /* doesn't work on some boards, probably a HW BUG */ + if (rate) { + clk_reg_disable(clk); /*enable bit is inverted */ + if (!clk_wait_for_pll_lock(clk)) { + clk->rate = CLK_RATE_13MHZ; + } else { + clk_reg_enable(clk); + clk->rate = 0; + } + + } else { + clk_reg_enable(clk); + clk->rate = 0; + } +#endif + return 0; +} + +/* Clock sources */ + +static struct clk osc_13MHz = { + .name = "osc_13MHz", + .flags = FIXED_RATE, + .rate = CLK_RATE_13MHZ, +}; + +static struct clk ck_13MHz = { + .name = "ck_13MHz", + .parent = &osc_13MHz, + .flags = NEEDS_INITIALIZATION, + .round_rate = &ck_13MHz_round_rate, + .set_rate = &ck_13MHz_set_rate, + .enable_reg = OSC13CTRL_REG, + .enable_shift = 0, + .rate = CLK_RATE_13MHZ, +}; + +static struct clk osc_32KHz = { + .name = "osc_32KHz", + .flags = FIXED_RATE, + .rate = CLK_RATE_32KHZ, +}; + +/*attached to PLL5*/ +static struct clk ck_1MHz = { + .name = "ck_1MHz", + .flags = FIXED_RATE | PARENT_SET_RATE, + .parent = &ck_13MHz, +}; + +/* PLL1 (397) - provides 13' MHz clock */ +static struct clk ck_pll1 = { + .name = "ck_pll1", + .parent = &osc_32KHz, + .flags = NEEDS_INITIALIZATION, + .round_rate = &ck_13MHz_round_rate, + .set_rate = &pll1_set_rate, + .enable_reg = PLLCTRL_REG, + .enable_shift = 1, + .scale_reg = PLLCTRL_REG, + .rate = CLK_RATE_13MHZ, +}; + +/* CPU/Bus PLL */ +static struct clk ck_pll4 = { + .name = "ck_pll4", + .parent = &ck_pll1, + .flags = RATE_PROPAGATES | NEEDS_INITIALIZATION, + .propagate_next = &per_ck, + .round_rate = &pll4_round_rate, + .set_rate = &pll160_set_rate, + .rate = CLK_RATE_208MHZ, + .scale_reg = HCLKPLLCTRL_REG, + .enable_reg = PWRCTRL_REG, + .enable_shift = 2, + .parent_switch_reg = SYSCLKCTRL_REG, + .set_parent = &set_13MHz_parent, +}; + +/* USB PLL */ +static struct clk ck_pll5 = { + .name = "ck_pll5", + .parent = &ck_1MHz, + .flags = NEEDS_INITIALIZATION, + .round_rate = &pll5_round_rate, + .set_rate = &pll160_set_rate, + .scale_reg = USBCTRL_REG, + .enable_reg = USBCTRL_REG, + .enable_shift = 18, + .enable_reg1 = USBCTRL_REG, + .enable_shift1 = 17, +}; + +/* XPERTTeak DSP PLL */ +static struct clk ck_pll3 = { + .name = "ck_pll3", + .parent = &ck_pll1, + .flags = NEEDS_INITIALIZATION, + .round_rate = &pll3_round_rate, + .set_rate = &pll160_set_rate, + .scale_reg = DSPPLLCTRL_REG, + .enable_reg = DSPCLKCTRL_REG, + .enable_shift = 3, + .enable_reg1 = DSPCLKCTRL_REG, + .enable_shift1 = 2, + .parent_switch_reg = DSPCLKCTRL_REG, + .set_parent = &set_13MHz_parent, +}; + +static struct clk hclk_ck = { + .name = "hclk_ck", + .parent = &ck_pll4, + .flags = PARENT_SET_RATE, + .set_rate = &hclk_set_rate, + .round_rate = &hclk_round_rate, + .scale_reg = HCLKDIVCTRL_REG, + .rate = 2, + .user_rate = 2, +}; + +static struct clk per_ck = { + .name = "per_ck", + .parent = &ck_pll4, + .flags = FIXED_RATE, + .propagate_next = &hclk_ck, + .set_rate = &per_clk_set_rate, + .round_rate = &per_clk_round_rate, + .scale_reg = HCLKDIVCTRL_REG, + .rate = CLK_RATE_13MHZ, + .user_rate = CLK_RATE_13MHZ, +}; + +static struct clk m2hclk_ck = { + .name = "m2hclk_ck", + .parent = &hclk_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_inv_set_rate, + .rate = 1, + .enable_shift = 6, + .enable_reg = PWRCTRL_REG, +}; + +static struct clk vfp9_ck = { + .name = "vfp9_ck", + .parent = &ck_pll4, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .rate = 1, + .enable_shift = 4, + .enable_reg = VFP9CLKCTRL_REG, +}; + +static struct clk keyscan_ck = { + .name = "keyscan_ck", + .parent = &osc_32KHz, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 0, + .enable_reg = KEYCLKCTRL_REG, +}; + +static struct clk touch_ck = { + .name = "touch_ck", + .parent = &osc_32KHz, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 0, + .enable_reg = TSCLKCTRL_REG, +}; + +static struct clk pwm1_ck = { + .name = "pwm1_ck", + .parent = &osc_32KHz, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 0, + .enable_reg = PWMCLKCTRL_REG, +}; + +static struct clk pwm2_ck = { + .name = "pwm2_ck", + .parent = &osc_32KHz, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 2, + .enable_reg = PWMCLKCTRL_REG, +}; + +static struct clk jpeg_ck = { + .name = "jpeg_ck", + .parent = &hclk_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 0, + .enable_reg = JPEGCLKCTRL_REG, +}; + +static struct clk ms_ck = { + .name = "ms_ck", + .parent = &ck_pll4, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 5, + .enable_reg = MSCTRL_REG, +}; + +static struct clk dum_ck = { + .name = "dum_ck", + .parent = &hclk_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 0, + .enable_reg = DUMCLKCTRL_REG, +}; + +static struct clk flash_ck = { + .name = "flash_ck", + .parent = &hclk_ck, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 1, /* Only MLC clock supported */ + .enable_reg = FLASHCLKCTRL_REG, +}; + +static struct clk i2c0_ck = { + .name = "i2c0_ck", + .parent = &per_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 0, + .enable_reg = I2CCLKCTRL_REG, +}; + +static struct clk i2c1_ck = { + .name = "i2c1_ck", + .parent = &per_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 1, + .enable_reg = I2CCLKCTRL_REG, +}; + +static struct clk i2c2_ck = { + .name = "i2c2_ck", + .parent = &per_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 2, + .enable_reg = USB_OTG_CLKCTRL_REG, +}; + +static struct clk spi0_ck = { + .name = "spi0_ck", + .parent = &hclk_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 0, + .enable_reg = SPICTRL_REG, +}; + +static struct clk spi1_ck = { + .name = "spi1_ck", + .parent = &hclk_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 4, + .enable_reg = SPICTRL_REG, +}; + +static struct clk dma_ck = { + .name = "dma_ck", + .parent = &hclk_ck, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 0, + .enable_reg = DMACLKCTRL_REG, +}; + +static struct clk uart3_ck = { + .name = "uart3_ck", + .parent = &per_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .rate = 1, + .enable_shift = 0, + .enable_reg = UARTCLKCTRL_REG, +}; + +static struct clk uart4_ck = { + .name = "uart4_ck", + .parent = &per_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 1, + .enable_reg = UARTCLKCTRL_REG, +}; + +static struct clk uart5_ck = { + .name = "uart5_ck", + .parent = &per_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .rate = 1, + .enable_shift = 2, + .enable_reg = UARTCLKCTRL_REG, +}; + +static struct clk uart6_ck = { + .name = "uart6_ck", + .parent = &per_ck, + .flags = NEEDS_INITIALIZATION, + .round_rate = &on_off_round_rate, + .set_rate = &on_off_set_rate, + .enable_shift = 3, + .enable_reg = UARTCLKCTRL_REG, +}; + +/* These clocks are visible outside this module + * and can be initialized + */ +static struct clk *onchip_clks[] = { + &ck_13MHz, + &ck_pll1, + &ck_pll4, + &ck_pll5, + &ck_pll3, + &vfp9_ck, + &m2hclk_ck, + &hclk_ck, + &dma_ck, + &flash_ck, + &dum_ck, + &keyscan_ck, + &pwm1_ck, + &pwm2_ck, + &jpeg_ck, + &ms_ck, + &touch_ck, + &i2c0_ck, + &i2c1_ck, + &i2c2_ck, + &spi0_ck, + &spi1_ck, + &uart3_ck, + &uart4_ck, + &uart5_ck, + &uart6_ck, +}; + +static int local_set_rate(struct clk *clk, u32 rate) +{ + int ret = -EINVAL; + if (clk->set_rate) { + + if (clk->user_rate == clk->rate && clk->parent->rate) { + /* if clock enabled or rate not set */ + clk->user_rate = clk->round_rate(clk, rate); + ret = clk->set_rate(clk, clk->user_rate); + } else + clk->user_rate = clk->round_rate(clk, rate); + ret = 0; + } + return ret; +} + +int clk_set_rate(struct clk *clk, unsigned long rate) +{ + int ret = -EINVAL; + + if (clk->flags & FIXED_RATE) + goto out; + + clock_lock(); + if ((clk->flags & PARENT_SET_RATE) && clk->parent) { + + clk->user_rate = clk->round_rate(clk, rate); + /* parent clock needs to be refreshed + for the setting to take effect */ + } else { + ret = local_set_rate(clk, rate); + } + ret = 0; + clock_unlock(); + +out: + return ret; +} + +EXPORT_SYMBOL(clk_set_rate); + +struct clk *clk_get(struct device *dev, const char *id) +{ + struct clk *clk = ERR_PTR(-ENOENT); + struct clk **clkp; + + clock_lock(); + for (clkp = onchip_clks; clkp < onchip_clks + ARRAY_SIZE(onchip_clks); + clkp++) { + if (strcmp(id, (*clkp)->name) == 0 + && try_module_get((*clkp)->owner)) { + clk = (*clkp); + break; + } + } + clock_unlock(); + + return clk; +} +EXPORT_SYMBOL(clk_get); + +void clk_put(struct clk *clk) +{ + clock_lock(); + if (clk && !IS_ERR(clk)) + module_put(clk->owner); + clock_unlock(); +} +EXPORT_SYMBOL(clk_put); + +unsigned long clk_get_rate(struct clk *clk) +{ + unsigned long ret; + clock_lock(); + ret = clk->rate; + clock_unlock(); + return ret; +} +EXPORT_SYMBOL(clk_get_rate); + +static int local_clk_enable(struct clk *clk) +{ + int ret = 0; + + if (!(clk->flags & FIXED_RATE) && !clk->rate && clk->set_rate + && clk->user_rate) + ret = clk->set_rate(clk, clk->user_rate); + return ret; +} + +static void local_clk_disable(struct clk *clk) +{ + if (!(clk->flags & FIXED_RATE) && clk->rate && clk->set_rate) + clk->set_rate(clk, 0); +} + +int clk_enable(struct clk *clk) +{ + int ret = 0; + + clock_lock(); + ret = local_clk_enable(clk); + clock_unlock(); + return ret; +} + +EXPORT_SYMBOL(clk_enable); + +void clk_disable(struct clk *clk) +{ + clock_lock(); + local_clk_disable(clk); + clock_unlock(); +} + +EXPORT_SYMBOL(clk_disable); + +static void local_clk_unuse(struct clk *clk) +{ + if (clk->usecount > 0 && !(--clk->usecount)) { + local_clk_disable(clk); + if (clk->parent) + local_clk_unuse(clk->parent); + } +} + +static int local_clk_use(struct clk *clk) +{ + int ret = 0; + if (clk->usecount++ == 0) { + if (clk->parent) + ret = local_clk_use(clk->parent); + + if (ret != 0) { + clk->usecount--; + goto out; + } + + ret = local_clk_enable(clk); + + if (ret != 0 && clk->parent) { + local_clk_unuse(clk->parent); + clk->usecount--; + } + } +out: + return ret; +} + +/* The main purpose of clk_use ans clk_unuse functions + * is to control switching 13MHz oscillator and PLL1 (13'MHz), + * so that they are disabled whenever none of PLL2-5 is using them. + * Although in theory these functions should work with any clock, + * please use them only on PLL2 - PLL5 to avoid confusion. + */ +int clk_use(struct clk *clk) +{ + int ret = 0; + + clock_lock(); + ret = local_clk_use(clk); + clock_unlock(); + return ret; +} +EXPORT_SYMBOL(clk_use); + +void clk_unuse(struct clk *clk) +{ + + clock_lock(); + local_clk_unuse(clk); + clock_unlock(); +} + +EXPORT_SYMBOL(clk_unuse); + +long clk_round_rate(struct clk *clk, unsigned long rate) +{ + long ret; + clock_lock(); + if (clk->round_rate) + ret = clk->round_rate(clk, rate); + else + ret = clk->rate; + clock_unlock(); + return ret; +} + +EXPORT_SYMBOL(clk_round_rate); + +int clk_set_parent(struct clk *clk, struct clk *parent) +{ + int ret = -ENODEV; + if (!clk->set_parent) + goto out; + + clock_lock(); + ret = clk->set_parent(clk, parent); + if (!ret) + clk->parent = parent; + clock_unlock(); + +out: + return ret; +} + +EXPORT_SYMBOL(clk_set_parent); + +static int __init clk_init(void) +{ + struct clk **clkp; + + /* Disable autoclocking, as it doesn't seem to work */ + __raw_writel(0xff, AUTOCLK_CTRL); + + for (clkp = onchip_clks; clkp < onchip_clks + ARRAY_SIZE(onchip_clks); + clkp++) { + if (((*clkp)->flags & NEEDS_INITIALIZATION) + && ((*clkp)->set_rate)) { + (*clkp)->user_rate = (*clkp)->rate; + local_set_rate((*clkp), (*clkp)->user_rate); + if ((*clkp)->set_parent) + (*clkp)->set_parent((*clkp), (*clkp)->parent); + } + pr_debug("%s: clock %s, rate %ld\n", + __FUNCTION__, (*clkp)->name, (*clkp)->rate); + } + + clk_use(&ck_pll4); + + /* if ck_13MHz is not used, disable it. */ + if (ck_13MHz.usecount == 0) + local_clk_disable(&ck_13MHz); + + /* Disable autoclocking */ + __raw_writeb(0xff, AUTOCLK_CTRL); + + return 0; +} + +arch_initcall(clk_init); diff --git a/arch/arm/mach-pnx4008/clock.h b/arch/arm/mach-pnx4008/clock.h new file mode 100644 index 00000000000..cd58f372cfd --- /dev/null +++ b/arch/arm/mach-pnx4008/clock.h @@ -0,0 +1,43 @@ +/* + * arch/arm/mach-pnx4008/clock.h + * + * Clock control driver for PNX4008 - internal header file + * + * Author: Vitaly Wool <source@mvista.com> + * + * 2006 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#ifndef __ARCH_ARM_PNX4008_CLOCK_H__ +#define __ARCH_ARM_PNX4008_CLOCK_H__ + +struct clk { + struct list_head node; + struct module *owner; + const char *name; + struct clk *parent; + struct clk *propagate_next; + u32 rate; + u32 user_rate; + s8 usecount; + u32 flags; + u32 scale_reg; + u8 enable_shift; + u32 enable_reg; + u8 enable_shift1; + u32 enable_reg1; + u32 parent_switch_reg; + u32(*round_rate) (struct clk *, u32); + int (*set_rate) (struct clk *, u32); + int (*set_parent) (struct clk * clk, struct clk * parent); +}; + +/* Flags */ +#define RATE_PROPAGATES (1<<0) +#define NEEDS_INITIALIZATION (1<<1) +#define PARENT_SET_RATE (1<<2) +#define FIXED_RATE (1<<3) + +#endif diff --git a/arch/arm/mach-pnx4008/core.c b/arch/arm/mach-pnx4008/core.c new file mode 100644 index 00000000000..ba91daad64f --- /dev/null +++ b/arch/arm/mach-pnx4008/core.c @@ -0,0 +1,207 @@ +/* + * arch/arm/mach-pnx4008/core.c + * + * PNX4008 core startup code + * + * Authors: Vitaly Wool, Dmitry Chigirev, + * Grigory Tolstolytkin, Dmitry Pervushin <source@mvista.com> + * + * Based on reference code received from Philips: + * Copyright (C) 2003 Philips Semiconductors + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/mm.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/init.h> +#include <linux/ioport.h> +#include <linux/serial_8250.h> +#include <linux/device.h> +#include <linux/spi/spi.h> + +#include <asm/hardware.h> +#include <asm/irq.h> +#include <asm/io.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/pgtable.h> +#include <asm/page.h> +#include <asm/system.h> + +#include <asm/mach/arch.h> +#include <asm/mach/irq.h> +#include <asm/mach/map.h> +#include <asm/mach/time.h> + +#include <asm/arch/irq.h> +#include <asm/arch/clock.h> +#include <asm/arch/dma.h> + +struct resource spipnx_0_resources[] = { + { + .start = PNX4008_SPI1_BASE, + .end = PNX4008_SPI1_BASE + SZ_4K, + .flags = IORESOURCE_MEM, + }, { + .start = PER_SPI1_REC_XMIT, + .flags = IORESOURCE_DMA, + }, { + .start = SPI1_INT, + .flags = IORESOURCE_IRQ, + }, { + .flags = 0, + }, +}; + +struct resource spipnx_1_resources[] = { + { + .start = PNX4008_SPI2_BASE, + .end = PNX4008_SPI2_BASE + SZ_4K, + .flags = IORESOURCE_MEM, + }, { + .start = PER_SPI2_REC_XMIT, + .flags = IORESOURCE_DMA, + }, { + .start = SPI2_INT, + .flags = IORESOURCE_IRQ, + }, { + .flags = 0, + } +}; + +static struct spi_board_info spi_board_info[] __initdata = { + { + .modalias = "m25p80", + .max_speed_hz = 1000000, + .bus_num = 1, + .chip_select = 0, + }, +}; + +static struct platform_device spipnx_1 = { + .name = "spipnx", + .id = 1, + .num_resources = ARRAY_SIZE(spipnx_0_resources), + .resource = spipnx_0_resources, + .dev = { + .coherent_dma_mask = 0xFFFFFFFF, + }, +}; + +static struct platform_device spipnx_2 = { + .name = "spipnx", + .id = 2, + .num_resources = ARRAY_SIZE(spipnx_1_resources), + .resource = spipnx_1_resources, + .dev = { + .coherent_dma_mask = 0xFFFFFFFF, + }, +}; + +static struct plat_serial8250_port platform_serial_ports[] = { + { + .membase = (void *)__iomem(IO_ADDRESS(PNX4008_UART5_BASE)), + .mapbase = (unsigned long)PNX4008_UART5_BASE, + .irq = IIR5_INT, + .uartclk = PNX4008_UART_CLK, + .regshift = 2, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | UPF_SKIP_TEST, + }, + { + .membase = (void *)__iomem(IO_ADDRESS(PNX4008_UART3_BASE)), + .mapbase = (unsigned long)PNX4008_UART3_BASE, + .irq = IIR3_INT, + .uartclk = PNX4008_UART_CLK, + .regshift = 2, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | UPF_SKIP_TEST, + }, + {} +}; + +static struct platform_device serial_device = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = &platform_serial_ports, + }, +}; + +static struct platform_device *devices[] __initdata = { + &spipnx_1, + &spipnx_2, + &serial_device, +}; + + +extern void pnx4008_uart_init(void); + +static void __init pnx4008_init(void) +{ + /*disable all START interrupt sources, + and clear all START interrupt flags */ + __raw_writel(0, START_INT_ER_REG(SE_PIN_BASE_INT)); + __raw_writel(0, START_INT_ER_REG(SE_INT_BASE_INT)); + __raw_writel(0xffffffff, START_INT_RSR_REG(SE_PIN_BASE_INT)); + __raw_writel(0xffffffff, START_INT_RSR_REG(SE_INT_BASE_INT)); + + platform_add_devices(devices, ARRAY_SIZE(devices)); + spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info)); + /* Switch on the UART clocks */ + pnx4008_uart_init(); +} + +static struct map_desc pnx4008_io_desc[] __initdata = { + { + .virtual = IO_ADDRESS(PNX4008_IRAM_BASE), + .pfn = __phys_to_pfn(PNX4008_IRAM_BASE), + .length = SZ_64K, + .type = MT_DEVICE, + }, { + .virtual = IO_ADDRESS(PNX4008_NDF_FLASH_BASE), + .pfn = __phys_to_pfn(PNX4008_NDF_FLASH_BASE), + .length = SZ_1M - SZ_128K, + .type = MT_DEVICE, + }, { + .virtual = IO_ADDRESS(PNX4008_JPEG_CONFIG_BASE), + .pfn = __phys_to_pfn(PNX4008_JPEG_CONFIG_BASE), + .length = SZ_128K * 3, + .type = MT_DEVICE, + }, { + .virtual = IO_ADDRESS(PNX4008_DMA_CONFIG_BASE), + .pfn = __phys_to_pfn(PNX4008_DMA_CONFIG_BASE), + .length = SZ_1M, + .type = MT_DEVICE, + }, { + .virtual = IO_ADDRESS(PNX4008_AHB2FAB_BASE), + .pfn = __phys_to_pfn(PNX4008_AHB2FAB_BASE), + .length = SZ_1M, + .type = MT_DEVICE, + }, +}; + +void __init pnx4008_map_io(void) +{ + iotable_init(pnx4008_io_desc, ARRAY_SIZE(pnx4008_io_desc)); +} + +extern struct sys_timer pnx4008_timer; + +MACHINE_START(PNX4008, "Philips PNX4008") + /* Maintainer: MontaVista Software Inc. */ + .phys_io = 0x40090000, + .io_pg_offst = (0xf4090000 >> 18) & 0xfffc, + .boot_params = 0x80000100, + .map_io = pnx4008_map_io, + .init_irq = pnx4008_init_irq, + .init_machine = pnx4008_init, + .timer = &pnx4008_timer, +MACHINE_END diff --git a/arch/arm/mach-pnx4008/dma.c b/arch/arm/mach-pnx4008/dma.c new file mode 100644 index 00000000000..981aa9dcded --- /dev/null +++ b/arch/arm/mach-pnx4008/dma.c @@ -0,0 +1,1109 @@ +/* + * linux/arch/arm/mach-pnx4008/dma.c + * + * PNX4008 DMA registration and IRQ dispatching + * + * Author: Vitaly Wool + * Copyright: MontaVista Software Inc. (c) 2005 + * + * Based on the code from Nicolas Pitre + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/interrupt.h> +#include <linux/errno.h> +#include <linux/err.h> +#include <linux/dma-mapping.h> +#include <linux/clk.h> + +#include <asm/system.h> +#include <asm/irq.h> +#include <asm/hardware.h> +#include <asm/dma.h> +#include <asm/dma-mapping.h> +#include <asm/io.h> +#include <asm/mach/dma.h> +#include <asm/arch/clock.h> + +static struct dma_channel { + char *name; + void (*irq_handler) (int, int, void *, struct pt_regs *); + void *data; + struct pnx4008_dma_ll *ll; + u32 ll_dma; + void *target_addr; + int target_id; +} dma_channels[MAX_DMA_CHANNELS]; + +static struct ll_pool { + void *vaddr; + void *cur; + dma_addr_t dma_addr; + int count; +} ll_pool; + +static spinlock_t ll_lock = SPIN_LOCK_UNLOCKED; + +struct pnx4008_dma_ll *pnx4008_alloc_ll_entry(dma_addr_t * ll_dma) +{ + struct pnx4008_dma_ll *ll = NULL; + unsigned long flags; + + spin_lock_irqsave(&ll_lock, flags); + if (ll_pool.count > 4) { /* can give one more */ + ll = *(struct pnx4008_dma_ll **) ll_pool.cur; + *ll_dma = ll_pool.dma_addr + ((void *)ll - ll_pool.vaddr); + *(void **)ll_pool.cur = **(void ***)ll_pool.cur; + memset(ll, 0, sizeof(*ll)); + ll_pool.count--; + } + spin_unlock_irqrestore(&ll_lock, flags); + + return ll; +} + +EXPORT_SYMBOL_GPL(pnx4008_alloc_ll_entry); + +void pnx4008_free_ll_entry(struct pnx4008_dma_ll * ll, dma_addr_t ll_dma) +{ + unsigned long flags; + + if (ll) { + if ((unsigned long)((long)ll - (long)ll_pool.vaddr) > 0x4000) { + printk(KERN_ERR "Trying to free entry not allocated by DMA\n"); + BUG(); + } + + if (ll->flags & DMA_BUFFER_ALLOCATED) + ll->free(ll->alloc_data); + + spin_lock_irqsave(&ll_lock, flags); + *(long *)ll = *(long *)ll_pool.cur; + *(long *)ll_pool.cur = (long)ll; + ll_pool.count++; + spin_unlock_irqrestore(&ll_lock, flags); + } +} + +EXPORT_SYMBOL_GPL(pnx4008_free_ll_entry); + +void pnx4008_free_ll(u32 ll_dma, struct pnx4008_dma_ll * ll) +{ + struct pnx4008_dma_ll *ptr; + u32 dma; + + while (ll) { + dma = ll->next_dma; + ptr = ll->next; + pnx4008_free_ll_entry(ll, ll_dma); + + ll_dma = dma; + ll = ptr; + } +} + +EXPORT_SYMBOL_GPL(pnx4008_free_ll); + +static int dma_channels_requested = 0; + +static inline void dma_increment_usage(void) +{ + if (!dma_channels_requested++) { + struct clk *clk = clk_get(0, "dma_ck"); + if (!IS_ERR(clk)) { + clk_set_rate(clk, 1); + clk_put(clk); + } + pnx4008_config_dma(-1, -1, 1); + } +} +static inline void dma_decrement_usage(void) +{ + if (!--dma_channels_requested) { + struct clk *clk = clk_get(0, "dma_ck"); + if (!IS_ERR(clk)) { + clk_set_rate(clk, 0); + clk_put(clk); + } + pnx4008_config_dma(-1, -1, 0); + + } +} + +static spinlock_t dma_lock = SPIN_LOCK_UNLOCKED; + +static inline void pnx4008_dma_lock(void) +{ + spin_lock_irq(&dma_lock); +} + +static inline void pnx4008_dma_unlock(void) +{ + spin_unlock_irq(&dma_lock); +} + +#define VALID_CHANNEL(c) (((c) >= 0) && ((c) < MAX_DMA_CHANNELS)) + +int pnx4008_request_channel(char *name, int ch, + void (*irq_handler) (int, int, void *, + struct pt_regs *), void *data) +{ + int i, found = 0; + + /* basic sanity checks */ + if (!name || (ch != -1 && !VALID_CHANNEL(ch))) + return -EINVAL; + + pnx4008_dma_lock(); + + /* try grabbing a DMA channel with the requested priority */ + for (i = MAX_DMA_CHANNELS - 1; i >= 0; i--) { + if (!dma_channels[i].name && (ch == -1 || ch == i)) { + found = 1; + break; + } + } + + if (found) { + dma_increment_usage(); + dma_channels[i].name = name; + dma_channels[i].irq_handler = irq_handler; + dma_channels[i].data = data; + dma_channels[i].ll = NULL; + dma_channels[i].ll_dma = 0; + } else { + printk(KERN_WARNING "No more available DMA channels for %s\n", + name); + i = -ENODEV; + } + + pnx4008_dma_unlock(); + return i; +} + +EXPORT_SYMBOL_GPL(pnx4008_request_channel); + +void pnx4008_free_channel(int ch) +{ + if (!dma_channels[ch].name) { + printk(KERN_CRIT + "%s: trying to free channel %d which is already freed\n", + __FUNCTION__, ch); + return; + } + + pnx4008_dma_lock(); + pnx4008_free_ll(dma_channels[ch].ll_dma, dma_channels[ch].ll); + dma_channels[ch].ll = NULL; + dma_decrement_usage(); + + dma_channels[ch].name = NULL; + pnx4008_dma_unlock(); +} + +EXPORT_SYMBOL_GPL(pnx4008_free_channel); + +int pnx4008_config_dma(int ahb_m1_be, int ahb_m2_be, int enable) +{ + unsigned long dma_cfg = __raw_readl(DMAC_CONFIG); + + switch (ahb_m1_be) { + case 0: + dma_cfg &= ~(1 << 1); + break; + case 1: + dma_cfg |= (1 << 1); + break; + default: + break; + } + + switch (ahb_m2_be) { + case 0: + dma_cfg &= ~(1 << 2); + break; + case 1: + dma_cfg |= (1 << 2); + break; + default: + break; + } + + switch (enable) { + case 0: + dma_cfg &= ~(1 << 0); + break; + case 1: + dma_cfg |= (1 << 0); + break; + default: + break; + } + + pnx4008_dma_lock(); + __raw_writel(dma_cfg, DMAC_CONFIG); + pnx4008_dma_unlock(); + + return 0; +} + +EXPORT_SYMBOL_GPL(pnx4008_config_dma); + +int pnx4008_dma_pack_control(const struct pnx4008_dma_ch_ctrl * ch_ctrl, + unsigned long *ctrl) +{ + int i = 0, dbsize, sbsize, err = 0; + + if (!ctrl || !ch_ctrl) { + err = -EINVAL; + goto out; + } + + *ctrl = 0; + + switch (ch_ctrl->tc_mask) { + case 0: + break; + case 1: + *ctrl |= (1 << 31); + break; + + default: + err = -EINVAL; + goto out; + } + + switch (ch_ctrl->cacheable) { + case 0: + break; + case 1: + *ctrl |= (1 << 30); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_ctrl->bufferable) { + case 0: + break; + case 1: + *ctrl |= (1 << 29); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_ctrl->priv_mode) { + case 0: + break; + case 1: + *ctrl |= (1 << 28); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_ctrl->di) { + case 0: + break; + case 1: + *ctrl |= (1 << 27); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_ctrl->si) { + case 0: + break; + case 1: + *ctrl |= (1 << 26); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_ctrl->dest_ahb1) { + case 0: + break; + case 1: + *ctrl |= (1 << 25); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_ctrl->src_ahb1) { + case 0: + break; + case 1: + *ctrl |= (1 << 24); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_ctrl->dwidth) { + case WIDTH_BYTE: + *ctrl &= ~(7 << 21); + break; + case WIDTH_HWORD: + *ctrl &= ~(7 << 21); + *ctrl |= (1 << 21); + break; + case WIDTH_WORD: + *ctrl &= ~(7 << 21); + *ctrl |= (2 << 21); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_ctrl->swidth) { + case WIDTH_BYTE: + *ctrl &= ~(7 << 18); + break; + case WIDTH_HWORD: + *ctrl &= ~(7 << 18); + *ctrl |= (1 << 18); + break; + case WIDTH_WORD: + *ctrl &= ~(7 << 18); + *ctrl |= (2 << 18); + break; + + default: + err = -EINVAL; + goto out; + } + dbsize = ch_ctrl->dbsize; + while (!(dbsize & 1)) { + i++; + dbsize >>= 1; + } + if (ch_ctrl->dbsize != 1 || i > 8 || i == 1) { + err = -EINVAL; + goto out; + } else if (i > 1) + i--; + *ctrl &= ~(7 << 15); + *ctrl |= (i << 15); + + sbsize = ch_ctrl->sbsize; + while (!(sbsize & 1)) { + i++; + sbsize >>= 1; + } + if (ch_ctrl->sbsize != 1 || i > 8 || i == 1) { + err = -EINVAL; + goto out; + } else if (i > 1) + i--; + *ctrl &= ~(7 << 12); + *ctrl |= (i << 12); + + if (ch_ctrl->tr_size > 0x7ff) { + err = -E2BIG; + goto out; + } + *ctrl &= ~0x7ff; + *ctrl |= ch_ctrl->tr_size & 0x7ff; + +out: + return err; +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_pack_control); + +int pnx4008_dma_parse_control(unsigned long ctrl, + struct pnx4008_dma_ch_ctrl * ch_ctrl) +{ + int err = 0; + + if (!ch_ctrl) { + err = -EINVAL; + goto out; + } + + ch_ctrl->tr_size = ctrl & 0x7ff; + ctrl >>= 12; + + ch_ctrl->sbsize = 1 << (ctrl & 7); + if (ch_ctrl->sbsize > 1) + ch_ctrl->sbsize <<= 1; + ctrl >>= 3; + + ch_ctrl->dbsize = 1 << (ctrl & 7); + if (ch_ctrl->dbsize > 1) + ch_ctrl->dbsize <<= 1; + ctrl >>= 3; + + switch (ctrl & 7) { + case 0: + ch_ctrl->swidth = WIDTH_BYTE; + break; + case 1: + ch_ctrl->swidth = WIDTH_HWORD; + break; + case 2: + ch_ctrl->swidth = WIDTH_WORD; + break; + default: + err = -EINVAL; + goto out; + } + ctrl >>= 3; + + switch (ctrl & 7) { + case 0: + ch_ctrl->dwidth = WIDTH_BYTE; + break; + case 1: + ch_ctrl->dwidth = WIDTH_HWORD; + break; + case 2: + ch_ctrl->dwidth = WIDTH_WORD; + break; + default: + err = -EINVAL; + goto out; + } + ctrl >>= 3; + + ch_ctrl->src_ahb1 = ctrl & 1; + ctrl >>= 1; + + ch_ctrl->dest_ahb1 = ctrl & 1; + ctrl >>= 1; + + ch_ctrl->si = ctrl & 1; + ctrl >>= 1; + + ch_ctrl->di = ctrl & 1; + ctrl >>= 1; + + ch_ctrl->priv_mode = ctrl & 1; + ctrl >>= 1; + + ch_ctrl->bufferable = ctrl & 1; + ctrl >>= 1; + + ch_ctrl->cacheable = ctrl & 1; + ctrl >>= 1; + + ch_ctrl->tc_mask = ctrl & 1; + +out: + return err; +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_parse_control); + +int pnx4008_dma_pack_config(const struct pnx4008_dma_ch_config * ch_cfg, + unsigned long *cfg) +{ + int err = 0; + + if (!cfg || !ch_cfg) { + err = -EINVAL; + goto out; + } + + *cfg = 0; + + switch (ch_cfg->halt) { + case 0: + break; + case 1: + *cfg |= (1 << 18); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_cfg->active) { + case 0: + break; + case 1: + *cfg |= (1 << 17); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_cfg->lock) { + case 0: + break; + case 1: + *cfg |= (1 << 16); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_cfg->itc) { + case 0: + break; + case 1: + *cfg |= (1 << 15); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_cfg->ie) { + case 0: + break; + case 1: + *cfg |= (1 << 14); + break; + + default: + err = -EINVAL; + goto out; + } + switch (ch_cfg->flow_cntrl) { + case FC_MEM2MEM_DMA: + *cfg &= ~(7 << 11); + break; + case FC_MEM2PER_DMA: + *cfg &= ~(7 << 11); + *cfg |= (1 << 11); + break; + case FC_PER2MEM_DMA: + *cfg &= ~(7 << 11); + *cfg |= (2 << 11); + break; + case FC_PER2PER_DMA: + *cfg &= ~(7 << 11); + *cfg |= (3 << 11); + break; + case FC_PER2PER_DPER: + *cfg &= ~(7 << 11); + *cfg |= (4 << 11); + break; + case FC_MEM2PER_PER: + *cfg &= ~(7 << 11); + *cfg |= (5 << 11); + break; + case FC_PER2MEM_PER: + *cfg &= ~(7 << 11); + *cfg |= (6 << 11); + break; + case FC_PER2PER_SPER: + *cfg |= (7 << 11); + break; + + default: + err = -EINVAL; + goto out; + } + *cfg &= ~(0x1f << 6); + *cfg |= ((ch_cfg->dest_per & 0x1f) << 6); + + *cfg &= ~(0x1f << 1); + *cfg |= ((ch_cfg->src_per & 0x1f) << 1); + +out: + return err; +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_pack_config); + +int pnx4008_dma_parse_config(unsigned long cfg, + struct pnx4008_dma_ch_config * ch_cfg) +{ + int err = 0; + + if (!ch_cfg) { + err = -EINVAL; + goto out; + } + + cfg >>= 1; + + ch_cfg->src_per = cfg & 0x1f; + cfg >>= 5; + + ch_cfg->dest_per = cfg & 0x1f; + cfg >>= 5; + + switch (cfg & 7) { + case 0: + ch_cfg->flow_cntrl = FC_MEM2MEM_DMA; + break; + case 1: + ch_cfg->flow_cntrl = FC_MEM2PER_DMA; + break; + case 2: + ch_cfg->flow_cntrl = FC_PER2MEM_DMA; + break; + case 3: + ch_cfg->flow_cntrl = FC_PER2PER_DMA; + break; + case 4: + ch_cfg->flow_cntrl = FC_PER2PER_DPER; + break; + case 5: + ch_cfg->flow_cntrl = FC_MEM2PER_PER; + break; + case 6: + ch_cfg->flow_cntrl = FC_PER2MEM_PER; + break; + case 7: + ch_cfg->flow_cntrl = FC_PER2PER_SPER; + } + cfg >>= 3; + + ch_cfg->ie = cfg & 1; + cfg >>= 1; + + ch_cfg->itc = cfg & 1; + cfg >>= 1; + + ch_cfg->lock = cfg & 1; + cfg >>= 1; + + ch_cfg->active = cfg & 1; + cfg >>= 1; + + ch_cfg->halt = cfg & 1; + +out: + return err; +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_parse_config); + +void pnx4008_dma_split_head_entry(struct pnx4008_dma_config * config, + struct pnx4008_dma_ch_ctrl * ctrl) +{ + int new_len = ctrl->tr_size, num_entries = 0; + int old_len = new_len; + int src_width, dest_width, count = 1; + + switch (ctrl->swidth) { + case WIDTH_BYTE: + src_width = 1; + break; + case WIDTH_HWORD: + src_width = 2; + break; + case WIDTH_WORD: + src_width = 4; + break; + default: + return; + } + + switch (ctrl->dwidth) { + case WIDTH_BYTE: + dest_width = 1; + break; + case WIDTH_HWORD: + dest_width = 2; + break; + case WIDTH_WORD: + dest_width = 4; + break; + default: + return; + } + + while (new_len > 0x7FF) { + num_entries++; + new_len = (ctrl->tr_size + num_entries) / (num_entries + 1); + } + if (num_entries != 0) { + struct pnx4008_dma_ll *ll = NULL; + config->ch_ctrl &= ~0x7ff; + config->ch_ctrl |= new_len; + if (!config->is_ll) { + config->is_ll = 1; + while (num_entries) { + if (!ll) { + config->ll = + pnx4008_alloc_ll_entry(&config-> + ll_dma); + ll = config->ll; + } else { + ll->next = + pnx4008_alloc_ll_entry(&ll-> + next_dma); + ll = ll->next; + } + + if (ctrl->si) + ll->src_addr = + config->src_addr + + src_width * new_len * count; + else + ll->src_addr = config->src_addr; + if (ctrl->di) + ll->dest_addr = + config->dest_addr + + dest_width * new_len * count; + else + ll->dest_addr = config->dest_addr; + ll->ch_ctrl = config->ch_ctrl & 0x7fffffff; + ll->next_dma = 0; + ll->next = NULL; + num_entries--; + count++; + } + } else { + struct pnx4008_dma_ll *ll_old = config->ll; + unsigned long ll_dma_old = config->ll_dma; + while (num_entries) { + if (!ll) { + config->ll = + pnx4008_alloc_ll_entry(&config-> + ll_dma); + ll = config->ll; + } else { + ll->next = + pnx4008_alloc_ll_entry(&ll-> + next_dma); + ll = ll->next; + } + + if (ctrl->si) + ll->src_addr = + config->src_addr + + src_width * new_len * count; + else + ll->src_addr = config->src_addr; + if (ctrl->di) + ll->dest_addr = + config->dest_addr + + dest_width * new_len * count; + else + ll->dest_addr = config->dest_addr; + ll->ch_ctrl = config->ch_ctrl & 0x7fffffff; + ll->next_dma = 0; + ll->next = NULL; + num_entries--; + count++; + } + ll->next_dma = ll_dma_old; + ll->next = ll_old; + } + /* adjust last length/tc */ + ll->ch_ctrl = config->ch_ctrl & (~0x7ff); + ll->ch_ctrl |= old_len - new_len * (count - 1); + config->ch_ctrl &= 0x7fffffff; + } +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_split_head_entry); + +void pnx4008_dma_split_ll_entry(struct pnx4008_dma_ll * cur_ll, + struct pnx4008_dma_ch_ctrl * ctrl) +{ + int new_len = ctrl->tr_size, num_entries = 0; + int old_len = new_len; + int src_width, dest_width, count = 1; + + switch (ctrl->swidth) { + case WIDTH_BYTE: + src_width = 1; + break; + case WIDTH_HWORD: + src_width = 2; + break; + case WIDTH_WORD: + src_width = 4; + break; + default: + return; + } + + switch (ctrl->dwidth) { + case WIDTH_BYTE: + dest_width = 1; + break; + case WIDTH_HWORD: + dest_width = 2; + break; + case WIDTH_WORD: + dest_width = 4; + break; + default: + return; + } + + while (new_len > 0x7FF) { + num_entries++; + new_len = (ctrl->tr_size + num_entries) / (num_entries + 1); + } + if (num_entries != 0) { + struct pnx4008_dma_ll *ll = NULL; + cur_ll->ch_ctrl &= ~0x7ff; + cur_ll->ch_ctrl |= new_len; + if (!cur_ll->next) { + while (num_entries) { + if (!ll) { + cur_ll->next = + pnx4008_alloc_ll_entry(&cur_ll-> + next_dma); + ll = cur_ll->next; + } else { + ll->next = + pnx4008_alloc_ll_entry(&ll-> + next_dma); + ll = ll->next; + } + + if (ctrl->si) + ll->src_addr = + cur_ll->src_addr + + src_width * new_len * count; + else + ll->src_addr = cur_ll->src_addr; + if (ctrl->di) + ll->dest_addr = + cur_ll->dest_addr + + dest_width * new_len * count; + else + ll->dest_addr = cur_ll->dest_addr; + ll->ch_ctrl = cur_ll->ch_ctrl & 0x7fffffff; + ll->next_dma = 0; + ll->next = NULL; + num_entries--; + count++; + } + } else { + struct pnx4008_dma_ll *ll_old = cur_ll->next; + unsigned long ll_dma_old = cur_ll->next_dma; + while (num_entries) { + if (!ll) { + cur_ll->next = + pnx4008_alloc_ll_entry(&cur_ll-> + next_dma); + ll = cur_ll->next; + } else { + ll->next = + pnx4008_alloc_ll_entry(&ll-> + next_dma); + ll = ll->next; + } + + if (ctrl->si) + ll->src_addr = + cur_ll->src_addr + + src_width * new_len * count; + else + ll->src_addr = cur_ll->src_addr; + if (ctrl->di) + ll->dest_addr = + cur_ll->dest_addr + + dest_width * new_len * count; + else + ll->dest_addr = cur_ll->dest_addr; + ll->ch_ctrl = cur_ll->ch_ctrl & 0x7fffffff; + ll->next_dma = 0; + ll->next = NULL; + num_entries--; + count++; + } + + ll->next_dma = ll_dma_old; + ll->next = ll_old; + } + /* adjust last length/tc */ + ll->ch_ctrl = cur_ll->ch_ctrl & (~0x7ff); + ll->ch_ctrl |= old_len - new_len * (count - 1); + cur_ll->ch_ctrl &= 0x7fffffff; + } +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_split_ll_entry); + +int pnx4008_config_channel(int ch, struct pnx4008_dma_config * config) +{ + if (!VALID_CHANNEL(ch) || !dma_channels[ch].name) + return -EINVAL; + + pnx4008_dma_lock(); + __raw_writel(config->src_addr, DMAC_Cx_SRC_ADDR(ch)); + __raw_writel(config->dest_addr, DMAC_Cx_DEST_ADDR(ch)); + + if (config->is_ll) + __raw_writel(config->ll_dma, DMAC_Cx_LLI(ch)); + else + __raw_writel(0, DMAC_Cx_LLI(ch)); + + __raw_writel(config->ch_ctrl, DMAC_Cx_CONTROL(ch)); + __raw_writel(config->ch_cfg, DMAC_Cx_CONFIG(ch)); + pnx4008_dma_unlock(); + + return 0; + +} + +EXPORT_SYMBOL_GPL(pnx4008_config_channel); + +int pnx4008_channel_get_config(int ch, struct pnx4008_dma_config * config) +{ + if (!VALID_CHANNEL(ch) || !dma_channels[ch].name || !config) + return -EINVAL; + + pnx4008_dma_lock(); + config->ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch)); + config->ch_ctrl = __raw_readl(DMAC_Cx_CONTROL(ch)); + + config->ll_dma = __raw_readl(DMAC_Cx_LLI(ch)); + config->is_ll = config->ll_dma ? 1 : 0; + + config->src_addr = __raw_readl(DMAC_Cx_SRC_ADDR(ch)); + config->dest_addr = __raw_readl(DMAC_Cx_DEST_ADDR(ch)); + pnx4008_dma_unlock(); + + return 0; +} + +EXPORT_SYMBOL_GPL(pnx4008_channel_get_config); + +int pnx4008_dma_ch_enable(int ch) +{ + unsigned long ch_cfg; + + if (!VALID_CHANNEL(ch) || !dma_channels[ch].name) + return -EINVAL; + + pnx4008_dma_lock(); + ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch)); + ch_cfg |= 1; + __raw_writel(ch_cfg, DMAC_Cx_CONFIG(ch)); + pnx4008_dma_unlock(); + + return 0; +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_ch_enable); + +int pnx4008_dma_ch_disable(int ch) +{ + unsigned long ch_cfg; + + if (!VALID_CHANNEL(ch) || !dma_channels[ch].name) + return -EINVAL; + + pnx4008_dma_lock(); + ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch)); + ch_cfg &= ~1; + __raw_writel(ch_cfg, DMAC_Cx_CONFIG(ch)); + pnx4008_dma_unlock(); + + return 0; +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_ch_disable); + +int pnx4008_dma_ch_enabled(int ch) +{ + unsigned long ch_cfg; + + if (!VALID_CHANNEL(ch) || !dma_channels[ch].name) + return -EINVAL; + + pnx4008_dma_lock(); + ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch)); + pnx4008_dma_unlock(); + + return ch_cfg & 1; +} + +EXPORT_SYMBOL_GPL(pnx4008_dma_ch_enabled); + +static irqreturn_t dma_irq_handler(int irq, void *dev_id, struct pt_regs *regs) +{ + int i; + unsigned long dint = __raw_readl(DMAC_INT_STAT); + unsigned long tcint = __raw_readl(DMAC_INT_TC_STAT); + unsigned long eint = __raw_readl(DMAC_INT_ERR_STAT); + unsigned long i_bit; + + for (i = MAX_DMA_CHANNELS - 1; i >= 0; i--) { + i_bit = 1 << i; + if (dint & i_bit) { + struct dma_channel *channel = &dma_channels[i]; + + if (channel->name && channel->irq_handler) { + int cause = 0; + + if (eint & i_bit) + cause |= DMA_ERR_INT; + if (tcint & i_bit) + cause |= DMA_TC_INT; + channel->irq_handler(i, cause, channel->data, + regs); + } else { + /* + * IRQ for an unregistered DMA channel + */ + printk(KERN_WARNING + "spurious IRQ for DMA channel %d\n", i); + } + if (tcint & i_bit) + __raw_writel(i_bit, DMAC_INT_TC_CLEAR); + if (eint & i_bit) + __raw_writel(i_bit, DMAC_INT_ERR_CLEAR); + } + } + return IRQ_HANDLED; +} + +static int __init pnx4008_dma_init(void) +{ + int ret, i; + + ret = request_irq(DMA_INT, dma_irq_handler, 0, "DMA", NULL); + if (ret) { + printk(KERN_CRIT "Wow! Can't register IRQ for DMA\n"); + goto out; + } + + ll_pool.count = 0x4000 / sizeof(struct pnx4008_dma_ll); + ll_pool.cur = ll_pool.vaddr = + dma_alloc_coherent(NULL, ll_pool.count * sizeof(struct pnx4008_dma_ll), + &ll_pool.dma_addr, GFP_KERNEL); + + if (!ll_pool.vaddr) { + ret = -ENOMEM; + free_irq(DMA_INT, NULL); + goto out; + } + + for (i = 0; i < ll_pool.count - 1; i++) { + void **addr = ll_pool.vaddr + i * sizeof(struct pnx4008_dma_ll); + *addr = (void *)addr + sizeof(struct pnx4008_dma_ll); + } + *(long *)(ll_pool.vaddr + + (ll_pool.count - 1) * sizeof(struct pnx4008_dma_ll)) = + (long)ll_pool.vaddr; + + __raw_writel(1, DMAC_CONFIG); + +out: + return ret; +} +arch_initcall(pnx4008_dma_init); diff --git a/arch/arm/mach-pnx4008/gpio.c b/arch/arm/mach-pnx4008/gpio.c new file mode 100644 index 00000000000..e1ce050d8fe --- /dev/null +++ b/arch/arm/mach-pnx4008/gpio.c @@ -0,0 +1,330 @@ +/* + * arch/arm/mach-pnx4008/gpio.c + * + * PNX4008 GPIO driver + * + * Author: Dmitry Chigirev <source@mvista.com> + * + * Based on reference code by Iwo Mergler and Z.Tabaaloute from Philips: + * Copyright (c) 2005 Koninklijke Philips Electronics N.V. + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#include <linux/config.h> +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <asm/semaphore.h> +#include <asm/io.h> +#include <asm/arch/platform.h> +#include <asm/arch/gpio.h> + +/* register definitions */ +#define PIO_VA_BASE IO_ADDRESS(PNX4008_PIO_BASE) + +#define PIO_INP_STATE (0x00U) +#define PIO_OUTP_SET (0x04U) +#define PIO_OUTP_CLR (0x08U) +#define PIO_OUTP_STATE (0x0CU) +#define PIO_DRV_SET (0x10U) +#define PIO_DRV_CLR (0x14U) +#define PIO_DRV_STATE (0x18U) +#define PIO_SDINP_STATE (0x1CU) +#define PIO_SDOUTP_SET (0x20U) +#define PIO_SDOUTP_CLR (0x24U) +#define PIO_MUX_SET (0x28U) +#define PIO_MUX_CLR (0x2CU) +#define PIO_MUX_STATE (0x30U) + +static inline void gpio_lock(void) +{ + local_irq_disable(); +} + +static inline void gpio_unlock(void) +{ + local_irq_enable(); +} + +/* Inline functions */ +static inline int gpio_read_bit(u32 reg, int gpio) +{ + u32 bit, val; + int ret = -EFAULT; + + if (gpio < 0) + goto out; + + bit = GPIO_BIT(gpio); + if (bit) { + val = __raw_readl(PIO_VA_BASE + reg); + ret = (val & bit) ? 1 : 0; + } +out: + return ret; +} + +static inline int gpio_set_bit(u32 reg, int gpio) +{ + u32 bit, val; + int ret = -EFAULT; + + if (gpio < 0) + goto out; + + bit = GPIO_BIT(gpio); + if (bit) { + val = __raw_readl(PIO_VA_BASE + reg); + val |= bit; + __raw_writel(val, PIO_VA_BASE + reg); + ret = 0; + } +out: + return ret; +} + +/* Very simple access control, bitmap for allocated/free */ +static unsigned long access_map[4]; +#define INP_INDEX 0 +#define OUTP_INDEX 1 +#define GPIO_INDEX 2 +#define MUX_INDEX 3 + +/*GPIO to Input Mapping */ +static short gpio_to_inp_map[32] = { + -1, -1, -1, -1, -1, -1, -1, -1, + -1, -1, -1, -1, -1, -1, -1, -1, + -1, -1, -1, -1, -1, -1, -1, -1, + -1, 10, 11, 12, 13, 14, 24, -1 +}; + +/*GPIO to Mux Mapping */ +static short gpio_to_mux_map[32] = { + -1, -1, -1, -1, -1, -1, -1, -1, + -1, -1, -1, -1, -1, -1, -1, -1, + -1, -1, -1, -1, -1, -1, -1, -1, + -1, -1, -1, 0, 1, 4, 5, -1 +}; + +/*Output to Mux Mapping */ +static short outp_to_mux_map[32] = { + -1, -1, -1, 6, -1, -1, -1, -1, + -1, -1, -1, -1, -1, -1, -1, -1, + -1, -1, -1, -1, -1, 2, -1, -1, + -1, -1, -1, -1, -1, -1, -1, -1 +}; + +int pnx4008_gpio_register_pin(unsigned short pin) +{ + unsigned long bit = GPIO_BIT(pin); + int ret = -EBUSY; /* Already in use */ + + gpio_lock(); + + if (GPIO_ISBID(pin)) { + if (access_map[GPIO_INDEX] & bit) + goto out; + access_map[GPIO_INDEX] |= bit; + + } else if (GPIO_ISRAM(pin)) { + if (access_map[GPIO_INDEX] & bit) + goto out; + access_map[GPIO_INDEX] |= bit; + + } else if (GPIO_ISMUX(pin)) { + if (access_map[MUX_INDEX] & bit) + goto out; + access_map[MUX_INDEX] |= bit; + + } else if (GPIO_ISOUT(pin)) { + if (access_map[OUTP_INDEX] & bit) + goto out; + access_map[OUTP_INDEX] |= bit; + + } else if (GPIO_ISIN(pin)) { + if (access_map[INP_INDEX] & bit) + goto out; + access_map[INP_INDEX] |= bit; + } else + goto out; + ret = 0; + +out: + gpio_unlock(); + return ret; +} + +EXPORT_SYMBOL(pnx4008_gpio_register_pin); + +int pnx4008_gpio_unregister_pin(unsigned short pin) +{ + unsigned long bit = GPIO_BIT(pin); + int ret = -EFAULT; /* Not registered */ + + gpio_lock(); + + if (GPIO_ISBID(pin)) { + if (~access_map[GPIO_INDEX] & bit) + goto out; + access_map[GPIO_INDEX] &= ~bit; + } else if (GPIO_ISRAM(pin)) { + if (~access_map[GPIO_INDEX] & bit) + goto out; + access_map[GPIO_INDEX] &= ~bit; + } else if (GPIO_ISMUX(pin)) { + if (~access_map[MUX_INDEX] & bit) + goto out; + access_map[MUX_INDEX] &= ~bit; + } else if (GPIO_ISOUT(pin)) { + if (~access_map[OUTP_INDEX] & bit) + goto out; + access_map[OUTP_INDEX] &= ~bit; + } else if (GPIO_ISIN(pin)) { + if (~access_map[INP_INDEX] & bit) + goto out; + access_map[INP_INDEX] &= ~bit; + } else + goto out; + ret = 0; + +out: + gpio_unlock(); + return ret; +} + +EXPORT_SYMBOL(pnx4008_gpio_unregister_pin); + +unsigned long pnx4008_gpio_read_pin(unsigned short pin) +{ + unsigned long ret = -EFAULT; + int gpio = GPIO_BIT_MASK(pin); + gpio_lock(); + if (GPIO_ISOUT(pin)) { + ret = gpio_read_bit(PIO_OUTP_STATE, gpio); + } else if (GPIO_ISRAM(pin)) { + if (gpio_read_bit(PIO_DRV_STATE, gpio) == 0) { + ret = gpio_read_bit(PIO_SDINP_STATE, gpio); + } + } else if (GPIO_ISBID(pin)) { + ret = gpio_read_bit(PIO_DRV_STATE, gpio); + if (ret > 0) + ret = gpio_read_bit(PIO_OUTP_STATE, gpio); + else if (ret == 0) + ret = + gpio_read_bit(PIO_INP_STATE, gpio_to_inp_map[gpio]); + } else if (GPIO_ISIN(pin)) { + ret = gpio_read_bit(PIO_INP_STATE, gpio); + } + gpio_unlock(); + return ret; +} + +EXPORT_SYMBOL(pnx4008_gpio_read_pin); + +/* Write Value to output */ +int pnx4008_gpio_write_pin(unsigned short pin, int output) +{ + int gpio = GPIO_BIT_MASK(pin); + int ret = -EFAULT; + + gpio_lock(); + if (GPIO_ISOUT(pin)) { + printk( "writing '%x' to '%x'\n", + gpio, output ? PIO_OUTP_SET : PIO_OUTP_CLR ); + ret = gpio_set_bit(output ? PIO_OUTP_SET : PIO_OUTP_CLR, gpio); + } else if (GPIO_ISRAM(pin)) { + if (gpio_read_bit(PIO_DRV_STATE, gpio) > 0) + ret = gpio_set_bit(output ? PIO_SDOUTP_SET : + PIO_SDOUTP_CLR, gpio); + } else if (GPIO_ISBID(pin)) { + if (gpio_read_bit(PIO_DRV_STATE, gpio) > 0) + ret = gpio_set_bit(output ? PIO_OUTP_SET : + PIO_OUTP_CLR, gpio); + } + gpio_unlock(); + return ret; +} + +EXPORT_SYMBOL(pnx4008_gpio_write_pin); + +/* Value = 1 : Set GPIO pin as output */ +/* Value = 0 : Set GPIO pin as input */ +int pnx4008_gpio_set_pin_direction(unsigned short pin, int output) +{ + int gpio = GPIO_BIT_MASK(pin); + int ret = -EFAULT; + + gpio_lock(); + if (GPIO_ISBID(pin) || GPIO_ISRAM(pin)) { + ret = gpio_set_bit(output ? PIO_DRV_SET : PIO_DRV_CLR, gpio); + } + gpio_unlock(); + return ret; +} + +EXPORT_SYMBOL(pnx4008_gpio_set_pin_direction); + +/* Read GPIO pin direction: 0= pin used as input, 1= pin used as output*/ +int pnx4008_gpio_read_pin_direction(unsigned short pin) +{ + int gpio = GPIO_BIT_MASK(pin); + int ret = -EFAULT; + + gpio_lock(); + if (GPIO_ISBID(pin) || GPIO_ISRAM(pin)) { + ret = gpio_read_bit(PIO_DRV_STATE, gpio); + } + gpio_unlock(); + return ret; +} + +EXPORT_SYMBOL(pnx4008_gpio_read_pin_direction); + +/* Value = 1 : Set pin to muxed function */ +/* Value = 0 : Set pin as GPIO */ +int pnx4008_gpio_set_pin_mux(unsigned short pin, int output) +{ + int gpio = GPIO_BIT_MASK(pin); + int ret = -EFAULT; + + gpio_lock(); + if (GPIO_ISBID(pin)) { + ret = + gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR, + gpio_to_mux_map[gpio]); + } else if (GPIO_ISOUT(pin)) { + ret = + gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR, + outp_to_mux_map[gpio]); + } else if (GPIO_ISMUX(pin)) { + ret = gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR, gpio); + } + gpio_unlock(); + return ret; +} + +EXPORT_SYMBOL(pnx4008_gpio_set_pin_mux); + +/* Read pin mux function: 0= pin used as GPIO, 1= pin used for muxed function*/ +int pnx4008_gpio_read_pin_mux(unsigned short pin) +{ + int gpio = GPIO_BIT_MASK(pin); + int ret = -EFAULT; + + gpio_lock(); + if (GPIO_ISBID(pin)) { + ret = gpio_read_bit(PIO_MUX_STATE, gpio_to_mux_map[gpio]); + } else if (GPIO_ISOUT(pin)) { + ret = gpio_read_bit(PIO_MUX_STATE, outp_to_mux_map[gpio]); + } else if (GPIO_ISMUX(pin)) { + ret = gpio_read_bit(PIO_MUX_STATE, gpio); + } + gpio_unlock(); + return ret; +} + +EXPORT_SYMBOL(pnx4008_gpio_read_pin_mux); diff --git a/arch/arm/mach-pnx4008/irq.c b/arch/arm/mach-pnx4008/irq.c new file mode 100644 index 00000000000..9b0a8e084e9 --- /dev/null +++ b/arch/arm/mach-pnx4008/irq.c @@ -0,0 +1,121 @@ +/* + * arch/arm/mach-pnx4008/irq.c + * + * PNX4008 IRQ controller driver + * + * Author: Dmitry Chigirev <source@mvista.com> + * + * Based on reference code received from Philips: + * Copyright (C) 2003 Philips Semiconductors + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/mm.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/init.h> +#include <linux/ioport.h> +#include <linux/device.h> +#include <asm/hardware.h> +#include <asm/irq.h> +#include <asm/io.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/pgtable.h> +#include <asm/page.h> +#include <asm/system.h> +#include <asm/mach/arch.h> +#include <asm/mach/irq.h> +#include <asm/mach/map.h> +#include <asm/arch/irq.h> + +static u8 pnx4008_irq_type[NR_IRQS] = PNX4008_IRQ_TYPES; + +static void pnx4008_mask_irq(unsigned int irq) +{ + __raw_writel(__raw_readl(INTC_ER(irq)) & ~INTC_BIT(irq), INTC_ER(irq)); /* mask interrupt */ +} + +static void pnx4008_unmask_irq(unsigned int irq) +{ + __raw_writel(__raw_readl(INTC_ER(irq)) | INTC_BIT(irq), INTC_ER(irq)); /* unmask interrupt */ +} + +static void pnx4008_mask_ack_irq(unsigned int irq) +{ + __raw_writel(__raw_readl(INTC_ER(irq)) & ~INTC_BIT(irq), INTC_ER(irq)); /* mask interrupt */ + __raw_writel(INTC_BIT(irq), INTC_SR(irq)); /* clear interrupt status */ +} + +static int pnx4008_set_irq_type(unsigned int irq, unsigned int type) +{ + switch (type) { + case IRQT_RISING: + __raw_writel(__raw_readl(INTC_ATR(irq)) | INTC_BIT(irq), INTC_ATR(irq)); /*edge sensitive */ + __raw_writel(__raw_readl(INTC_APR(irq)) | INTC_BIT(irq), INTC_APR(irq)); /*rising edge */ + set_irq_handler(irq, do_edge_IRQ); + break; + case IRQT_FALLING: + __raw_writel(__raw_readl(INTC_ATR(irq)) | INTC_BIT(irq), INTC_ATR(irq)); /*edge sensitive */ + __raw_writel(__raw_readl(INTC_APR(irq)) & ~INTC_BIT(irq), INTC_APR(irq)); /*falling edge */ + set_irq_handler(irq, do_edge_IRQ); + break; + case IRQT_LOW: + __raw_writel(__raw_readl(INTC_ATR(irq)) & ~INTC_BIT(irq), INTC_ATR(irq)); /*level sensitive */ + __raw_writel(__raw_readl(INTC_APR(irq)) & ~INTC_BIT(irq), INTC_APR(irq)); /*low level */ + set_irq_handler(irq, do_level_IRQ); + break; + case IRQT_HIGH: + __raw_writel(__raw_readl(INTC_ATR(irq)) & ~INTC_BIT(irq), INTC_ATR(irq)); /*level sensitive */ + __raw_writel(__raw_readl(INTC_APR(irq)) | INTC_BIT(irq), INTC_APR(irq)); /* high level */ + set_irq_handler(irq, do_level_IRQ); + break; + + /* IRQT_BOTHEDGE is not supported */ + default: + printk(KERN_ERR "PNX4008 IRQ: Unsupported irq type %d\n", type); + return -1; + } + return 0; +} + +static struct irqchip pnx4008_irq_chip = { + .ack = pnx4008_mask_ack_irq, + .mask = pnx4008_mask_irq, + .unmask = pnx4008_unmask_irq, + .set_type = pnx4008_set_irq_type, +}; + +void __init pnx4008_init_irq(void) +{ + unsigned int i; + + /* configure and enable IRQ 0,1,30,31 (cascade interrupts) mask all others */ + pnx4008_set_irq_type(SUB1_IRQ_N, pnx4008_irq_type[SUB1_IRQ_N]); + pnx4008_set_irq_type(SUB2_IRQ_N, pnx4008_irq_type[SUB2_IRQ_N]); + pnx4008_set_irq_type(SUB1_FIQ_N, pnx4008_irq_type[SUB1_FIQ_N]); + pnx4008_set_irq_type(SUB2_FIQ_N, pnx4008_irq_type[SUB2_FIQ_N]); + + __raw_writel((1 << SUB2_FIQ_N) | (1 << SUB1_FIQ_N) | + (1 << SUB2_IRQ_N) | (1 << SUB1_IRQ_N), + INTC_ER(MAIN_BASE_INT)); + __raw_writel(0, INTC_ER(SIC1_BASE_INT)); + __raw_writel(0, INTC_ER(SIC2_BASE_INT)); + + /* configure all other IRQ's */ + for (i = 0; i < NR_IRQS; i++) { + if (i == SUB2_FIQ_N || i == SUB1_FIQ_N || + i == SUB2_IRQ_N || i == SUB1_IRQ_N) + continue; + set_irq_flags(i, IRQF_VALID); + set_irq_chip(i, &pnx4008_irq_chip); + pnx4008_set_irq_type(i, pnx4008_irq_type[i]); + } +} + diff --git a/arch/arm/mach-pnx4008/pm.c b/arch/arm/mach-pnx4008/pm.c new file mode 100644 index 00000000000..3649cd3dfc9 --- /dev/null +++ b/arch/arm/mach-pnx4008/pm.c @@ -0,0 +1,184 @@ +/* + * arch/arm/mach-pnx4008/pm.c + * + * Power Management driver for PNX4008 + * + * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com> + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#include <linux/pm.h> +#include <linux/rtc.h> +#include <linux/sched.h> +#include <linux/proc_fs.h> +#include <linux/pm.h> +#include <linux/delay.h> +#include <linux/clk.h> + +#include <asm/io.h> +#include <asm/mach-types.h> +#include <asm/cacheflush.h> +#include <asm/arch/pm.h> +#include <asm/arch/clock.h> + +#define SRAM_VA IO_ADDRESS(PNX4008_IRAM_BASE) + +static void *saved_sram; + +static struct clk *pll4_clk; + +static inline void pnx4008_standby(void) +{ + void (*pnx4008_cpu_standby_ptr) (void); + + local_irq_disable(); + local_fiq_disable(); + + clk_disable(pll4_clk); + + /*saving portion of SRAM to be used by suspend function. */ + memcpy(saved_sram, (void *)SRAM_VA, pnx4008_cpu_standby_sz); + + /*make sure SRAM copy gets physically written into SDRAM. + SDRAM will be placed into self-refresh during power down */ + flush_cache_all(); + + /*copy suspend function into SRAM */ + memcpy((void *)SRAM_VA, pnx4008_cpu_standby, pnx4008_cpu_standby_sz); + + /*do suspend */ + pnx4008_cpu_standby_ptr = (void *)SRAM_VA; + pnx4008_cpu_standby_ptr(); + + /*restoring portion of SRAM that was used by suspend function */ + memcpy((void *)SRAM_VA, saved_sram, pnx4008_cpu_standby_sz); + + clk_enable(pll4_clk); + + local_fiq_enable(); + local_irq_enable(); +} + +static inline void pnx4008_suspend(void) +{ + void (*pnx4008_cpu_suspend_ptr) (void); + + local_irq_disable(); + local_fiq_disable(); + + clk_disable(pll4_clk); + + __raw_writel(0xffffffff, START_INT_RSR_REG(SE_PIN_BASE_INT)); + __raw_writel(0xffffffff, START_INT_RSR_REG(SE_INT_BASE_INT)); + + /*saving portion of SRAM to be used by suspend function. */ + memcpy(saved_sram, (void *)SRAM_VA, pnx4008_cpu_suspend_sz); + + /*make sure SRAM copy gets physically written into SDRAM. + SDRAM will be placed into self-refresh during power down */ + flush_cache_all(); + + /*copy suspend function into SRAM */ + memcpy((void *)SRAM_VA, pnx4008_cpu_suspend, pnx4008_cpu_suspend_sz); + + /*do suspend */ + pnx4008_cpu_suspend_ptr = (void *)SRAM_VA; + pnx4008_cpu_suspend_ptr(); + + /*restoring portion of SRAM that was used by suspend function */ + memcpy((void *)SRAM_VA, saved_sram, pnx4008_cpu_suspend_sz); + + clk_enable(pll4_clk); + + local_fiq_enable(); + local_irq_enable(); +} + +static int pnx4008_pm_enter(suspend_state_t state) +{ + switch (state) { + case PM_SUSPEND_STANDBY: + pnx4008_standby(); + break; + case PM_SUSPEND_MEM: + pnx4008_suspend(); + break; + case PM_SUSPEND_DISK: + return -ENOTSUPP; + default: + return -EINVAL; + } + return 0; +} + +/* + * Called after processes are frozen, but before we shut down devices. + */ +static int pnx4008_pm_prepare(suspend_state_t state) +{ + switch (state) { + case PM_SUSPEND_STANDBY: + case PM_SUSPEND_MEM: + break; + + case PM_SUSPEND_DISK: + return -ENOTSUPP; + break; + + default: + return -EINVAL; + break; + } + return 0; +} + +/* + * Called after devices are re-setup, but before processes are thawed. + */ +static int pnx4008_pm_finish(suspend_state_t state) +{ + return 0; +} + +/* + * Set to PM_DISK_FIRMWARE so we can quickly veto suspend-to-disk. + */ +static struct pm_ops pnx4008_pm_ops = { + .prepare = pnx4008_pm_prepare, + .enter = pnx4008_pm_enter, + .finish = pnx4008_pm_finish, +}; + +static int __init pnx4008_pm_init(void) +{ + u32 sram_size_to_allocate; + + pll4_clk = clk_get(0, "ck_pll4"); + if (IS_ERR(pll4_clk)) { + printk(KERN_ERR + "PM Suspend cannot acquire ARM(PLL4) clock control\n"); + return PTR_ERR(pll4_clk); + } + + if (pnx4008_cpu_standby_sz > pnx4008_cpu_suspend_sz) + sram_size_to_allocate = pnx4008_cpu_standby_sz; + else + sram_size_to_allocate = pnx4008_cpu_suspend_sz; + + saved_sram = kmalloc(sram_size_to_allocate, GFP_ATOMIC); + if (!saved_sram) { + printk(KERN_ERR + "PM Suspend: cannot allocate memory to save portion of SRAM\n"); + clk_put(pll4_clk); + return -ENOMEM; + } + + pm_set_ops(&pnx4008_pm_ops); + return 0; +} + +late_initcall(pnx4008_pm_init); diff --git a/arch/arm/mach-pnx4008/serial.c b/arch/arm/mach-pnx4008/serial.c new file mode 100644 index 00000000000..2e1e04cc048 --- /dev/null +++ b/arch/arm/mach-pnx4008/serial.c @@ -0,0 +1,69 @@ +/* + * linux/arch/arm/mach-pnx4008/serial.c + * + * PNX4008 UART initialization + * + * Copyright: MontaVista Software Inc. (c) 2005 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/types.h> + +#include <asm/io.h> + +#include <asm/arch/platform.h> +#include <asm/arch/hardware.h> + +#include <linux/serial_core.h> +#include <linux/serial_reg.h> +#include <asm/arch/pm.h> + +#include <asm/arch/clock.h> + +#define UART_3 0 +#define UART_4 1 +#define UART_5 2 +#define UART_6 3 +#define UART_UNKNOWN (-1) + +#define UART3_BASE_VA IO_ADDRESS(PNX4008_UART3_BASE) +#define UART4_BASE_VA IO_ADDRESS(PNX4008_UART4_BASE) +#define UART5_BASE_VA IO_ADDRESS(PNX4008_UART5_BASE) +#define UART6_BASE_VA IO_ADDRESS(PNX4008_UART6_BASE) + +#define UART_FCR_OFFSET 8 +#define UART_FIFO_SIZE 64 + +void pnx4008_uart_init(void) +{ + u32 tmp; + int i = UART_FIFO_SIZE; + + __raw_writel(0xC1, UART5_BASE_VA + UART_FCR_OFFSET); + __raw_writel(0xC1, UART3_BASE_VA + UART_FCR_OFFSET); + + /* Send a NULL to fix the UART HW bug */ + __raw_writel(0x00, UART5_BASE_VA); + __raw_writel(0x00, UART3_BASE_VA); + + while (i--) { + tmp = __raw_readl(UART5_BASE_VA); + tmp = __raw_readl(UART3_BASE_VA); + } + __raw_writel(0, UART5_BASE_VA + UART_FCR_OFFSET); + __raw_writel(0, UART3_BASE_VA + UART_FCR_OFFSET); + + /* setup wakeup interrupt */ + start_int_set_rising_edge(SE_U3_RX_INT); + start_int_ack(SE_U3_RX_INT); + start_int_umask(SE_U3_RX_INT); + + start_int_set_rising_edge(SE_U5_RX_INT); + start_int_ack(SE_U5_RX_INT); + start_int_umask(SE_U5_RX_INT); +} + diff --git a/arch/arm/mach-pnx4008/sleep.S b/arch/arm/mach-pnx4008/sleep.S new file mode 100644 index 00000000000..93c802bac26 --- /dev/null +++ b/arch/arm/mach-pnx4008/sleep.S @@ -0,0 +1,196 @@ +/* + * linux/arch/arm/mach-pnx4008/sleep.S + * + * PNX4008 support for STOP mode and SDRAM self-refresh + * + * Authors: Dmitry Chigirev, Vitaly Wool <source@mvista.com> + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#include <linux/config.h> +#include <linux/linkage.h> +#include <asm/assembler.h> +#include <asm/hardware.h> + +#define PWRMAN_VA_BASE IO_ADDRESS(PNX4008_PWRMAN_BASE) +#define PWR_CTRL_REG_OFFS 0x44 + +#define SDRAM_CFG_VA_BASE IO_ADDRESS(PNX4008_SDRAM_CFG_BASE) +#define MPMC_STATUS_REG_OFFS 0x4 + + .text + +ENTRY(pnx4008_cpu_suspend) + @this function should be entered in Direct run mode. + + @ save registers on stack + stmfd sp!, {r0 - r6, lr} + + @ setup Power Manager base address in r4 + @ and put it's value in r5 + mov r4, #(PWRMAN_VA_BASE & 0xff000000) + orr r4, r4, #(PWRMAN_VA_BASE & 0x00ff0000) + orr r4, r4, #(PWRMAN_VA_BASE & 0x0000ff00) + orr r4, r4, #(PWRMAN_VA_BASE & 0x000000ff) + ldr r5, [r4, #PWR_CTRL_REG_OFFS] + + @ setup SDRAM controller base address in r2 + @ and put it's value in r3 + mov r2, #(SDRAM_CFG_VA_BASE & 0xff000000) + orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x00ff0000) + orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x0000ff00) + orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x000000ff) + ldr r3, [r2, #MPMC_STATUS_REG_OFFS] @extra read - HW bug workaround + + @ clear SDRAM self-refresh bit latch + and r5, r5, #(~(1 << 8)) + @ clear SDRAM self-refresh bit + and r5, r5, #(~(1 << 9)) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ do save current bit settings in r1 + mov r1, r5 + + @ set SDRAM self-refresh bit + orr r5, r5, #(1 << 9) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ set SDRAM self-refresh bit latch + orr r5, r5, #(1 << 8) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ clear SDRAM self-refresh bit latch + and r5, r5, #(~(1 << 8)) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ clear SDRAM self-refresh bit + and r5, r5, #(~(1 << 9)) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ wait for SDRAM to get into self-refresh mode +2: ldr r3, [r2, #MPMC_STATUS_REG_OFFS] + tst r3, #(1 << 2) + beq 2b + + @ to prepare SDRAM to get out of self-refresh mode after wakeup + orr r5, r5, #(1 << 7) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ do enter stop mode + orr r5, r5, #(1 << 0) + str r5, [r4, #PWR_CTRL_REG_OFFS] + nop + nop + nop + nop + nop + nop + nop + nop + nop + + @ sleeping now... + + @ coming out of STOP mode into Direct Run mode + @ clear STOP mode and SDRAM self-refresh bits + str r1, [r4, #PWR_CTRL_REG_OFFS] + + @ wait for SDRAM to get out self-refresh mode +3: ldr r3, [r2, #MPMC_STATUS_REG_OFFS] + tst r3, #5 + bne 3b + + @ restore regs and return + ldmfd sp!, {r0 - r6, pc} + +ENTRY(pnx4008_cpu_suspend_sz) + .word . - pnx4008_cpu_suspend + +ENTRY(pnx4008_cpu_standby) + @ save registers on stack + stmfd sp!, {r0 - r6, lr} + + @ setup Power Manager base address in r4 + @ and put it's value in r5 + mov r4, #(PWRMAN_VA_BASE & 0xff000000) + orr r4, r4, #(PWRMAN_VA_BASE & 0x00ff0000) + orr r4, r4, #(PWRMAN_VA_BASE & 0x0000ff00) + orr r4, r4, #(PWRMAN_VA_BASE & 0x000000ff) + ldr r5, [r4, #PWR_CTRL_REG_OFFS] + + @ setup SDRAM controller base address in r2 + @ and put it's value in r3 + mov r2, #(SDRAM_CFG_VA_BASE & 0xff000000) + orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x00ff0000) + orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x0000ff00) + orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x000000ff) + ldr r3, [r2, #MPMC_STATUS_REG_OFFS] @extra read - HW bug workaround + + @ clear SDRAM self-refresh bit latch + and r5, r5, #(~(1 << 8)) + @ clear SDRAM self-refresh bit + and r5, r5, #(~(1 << 9)) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ do save current bit settings in r1 + mov r1, r5 + + @ set SDRAM self-refresh bit + orr r5, r5, #(1 << 9) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ set SDRAM self-refresh bit latch + orr r5, r5, #(1 << 8) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ clear SDRAM self-refresh bit latch + and r5, r5, #(~(1 << 8)) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ clear SDRAM self-refresh bit + and r5, r5, #(~(1 << 9)) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ wait for SDRAM to get into self-refresh mode +2: ldr r3, [r2, #MPMC_STATUS_REG_OFFS] + tst r3, #(1 << 2) + beq 2b + + @ set 'get out of self-refresh mode after wakeup' bit + orr r5, r5, #(1 << 7) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + mcr p15, 0, r0, c7, c0, 4 @ kinda sleeping now... + + @ set SDRAM self-refresh bit latch + orr r5, r5, #(1 << 8) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ clear SDRAM self-refresh bit latch + and r5, r5, #(~(1 << 8)) + str r5, [r4, #PWR_CTRL_REG_OFFS] + + @ wait for SDRAM to get out self-refresh mode +3: ldr r3, [r2, #MPMC_STATUS_REG_OFFS] + tst r3, #5 + bne 3b + + @ restore regs and return + ldmfd sp!, {r0 - r6, pc} + +ENTRY(pnx4008_cpu_standby_sz) + .word . - pnx4008_cpu_standby + +ENTRY(pnx4008_cache_clean_invalidate) + stmfd sp!, {r0 - r6, lr} +#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH + mcr p15, 0, ip, c7, c6, 0 @ invalidate D cache +#else +1: mrc p15, 0, r15, c7, c14, 3 @ test,clean,invalidate + bne 1b +#endif + ldmfd sp!, {r0 - r6, pc} diff --git a/arch/arm/mach-pnx4008/time.c b/arch/arm/mach-pnx4008/time.c new file mode 100644 index 00000000000..4ce68069852 --- /dev/null +++ b/arch/arm/mach-pnx4008/time.c @@ -0,0 +1,141 @@ +/* + * arch/arm/mach-pnx4008/time.c + * + * PNX4008 Timers + * + * Authors: Vitaly Wool, Dmitry Chigirev, Grigory Tolstolytkin <source@mvista.com> + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#include <linux/config.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/sched.h> +#include <linux/spinlock.h> +#include <linux/module.h> +#include <linux/kallsyms.h> + +#include <asm/system.h> +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/leds.h> +#include <asm/irq.h> +#include <asm/mach/irq.h> +#include <asm/mach/time.h> + +#include <linux/time.h> +#include <linux/timex.h> +#include <asm/errno.h> + +/*! Note: all timers are UPCOUNTING */ + +/*! + * Returns number of us since last clock interrupt. Note that interrupts + * will have been disabled by do_gettimeoffset() + */ +static unsigned long pnx4008_gettimeoffset(void) +{ + u32 ticks_to_match = + __raw_readl(HSTIM_MATCH0) - __raw_readl(HSTIM_COUNTER); + u32 elapsed = LATCH - ticks_to_match; + return (elapsed * (tick_nsec / 1000)) / LATCH; +} + +/*! + * IRQ handler for the timer + */ +static irqreturn_t pnx4008_timer_interrupt(int irq, void *dev_id, + struct pt_regs *regs) +{ + if (__raw_readl(HSTIM_INT) & MATCH0_INT) { + + write_seqlock(&xtime_lock); + + do { + timer_tick(regs); + + /* + * this algorithm takes care of possible delay + * for this interrupt handling longer than a normal + * timer period + */ + __raw_writel(__raw_readl(HSTIM_MATCH0) + LATCH, + HSTIM_MATCH0); + __raw_writel(MATCH0_INT, HSTIM_INT); /* clear interrupt */ + + /* + * The goal is to keep incrementing HSTIM_MATCH0 + * register until HSTIM_MATCH0 indicates time after + * what HSTIM_COUNTER indicates. + */ + } while ((signed) + (__raw_readl(HSTIM_MATCH0) - + __raw_readl(HSTIM_COUNTER)) < 0); + + write_sequnlock(&xtime_lock); + } + + return IRQ_HANDLED; +} + +static struct irqaction pnx4008_timer_irq = { + .name = "PNX4008 Tick Timer", + .flags = SA_INTERRUPT | SA_TIMER, + .handler = pnx4008_timer_interrupt +}; + +/*! + * Set up timer and timer interrupt. + */ +static __init void pnx4008_setup_timer(void) +{ + __raw_writel(RESET_COUNT, MSTIM_CTRL); + while (__raw_readl(MSTIM_COUNTER)) ; /* wait for reset to complete. 100% guarantee event */ + __raw_writel(0, MSTIM_CTRL); /* stop the timer */ + __raw_writel(0, MSTIM_MCTRL); + + __raw_writel(RESET_COUNT, HSTIM_CTRL); + while (__raw_readl(HSTIM_COUNTER)) ; /* wait for reset to complete. 100% guarantee event */ + __raw_writel(0, HSTIM_CTRL); + __raw_writel(0, HSTIM_MCTRL); + __raw_writel(0, HSTIM_CCR); + __raw_writel(12, HSTIM_PMATCH); /* scale down to 1 MHZ */ + __raw_writel(LATCH, HSTIM_MATCH0); + __raw_writel(MR0_INT, HSTIM_MCTRL); + + setup_irq(HSTIMER_INT, &pnx4008_timer_irq); + + __raw_writel(COUNT_ENAB | DEBUG_EN, HSTIM_CTRL); /*start timer, stop when JTAG active */ +} + +/* Timer Clock Control in PM register */ +#define TIMCLK_CTRL_REG IO_ADDRESS((PNX4008_PWRMAN_BASE + 0xBC)) +#define WATCHDOG_CLK_EN 1 +#define TIMER_CLK_EN 2 /* HS and MS timers? */ + +static u32 timclk_ctrl_reg_save; + +void pnx4008_timer_suspend(void) +{ + timclk_ctrl_reg_save = __raw_readl(TIMCLK_CTRL_REG); + __raw_writel(0, TIMCLK_CTRL_REG); /* disable timers */ +} + +void pnx4008_timer_resume(void) +{ + __raw_writel(timclk_ctrl_reg_save, TIMCLK_CTRL_REG); /* enable timers */ +} + +struct sys_timer pnx4008_timer = { + .init = pnx4008_setup_timer, + .offset = pnx4008_gettimeoffset, + .suspend = pnx4008_timer_suspend, + .resume = pnx4008_timer_resume, +}; + diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c index 3e26d7ce5bb..1ab26c6914f 100644 --- a/arch/arm/mach-pxa/lubbock.c +++ b/arch/arm/mach-pxa/lubbock.c @@ -22,6 +22,10 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> +#include <linux/spi/spi.h> +#include <linux/spi/ads7846.h> +#include <asm/arch/pxa2xx_spi.h> + #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> @@ -196,6 +200,78 @@ static struct resource smc91x_resources[] = { }, }; +/* ADS7846 is connected through SSP ... and if your board has J5 populated, + * you can select it to replace the ucb1400 by switching the touchscreen cable + * (to J5) and poking board registers (as done below). Else it's only useful + * for the temperature sensors. + */ +static struct resource pxa_ssp_resources[] = { + [0] = { + .start = __PREG(SSCR0_P(1)), + .end = __PREG(SSCR0_P(1)) + 0x14, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_SSP, + .end = IRQ_SSP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct pxa2xx_spi_master pxa_ssp_master_info = { + .ssp_type = PXA25x_SSP, + .clock_enable = CKEN3_SSP, + .num_chipselect = 0, +}; + +static struct platform_device pxa_ssp = { + .name = "pxa2xx-spi", + .id = 1, + .resource = pxa_ssp_resources, + .num_resources = ARRAY_SIZE(pxa_ssp_resources), + .dev = { + .platform_data = &pxa_ssp_master_info, + }, +}; + +static int lubbock_ads7846_pendown_state(void) +{ + /* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */ + return 0; +} + +static struct ads7846_platform_data ads_info = { + .model = 7846, + .vref_delay_usecs = 100, /* internal, no cap */ + .get_pendown_state = lubbock_ads7846_pendown_state, + // .x_plate_ohms = 500, /* GUESS! */ + // .y_plate_ohms = 500, /* GUESS! */ +}; + +static void ads7846_cs(u32 command) +{ + static const unsigned TS_nCS = 1 << 11; + lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS); +} + +static struct pxa2xx_spi_chip ads_hw = { + .tx_threshold = 1, + .rx_threshold = 2, + .cs_control = ads7846_cs, +}; + +static struct spi_board_info spi_board_info[] __initdata = { { + .modalias = "ads7846", + .platform_data = &ads_info, + .controller_data = &ads_hw, + .irq = LUBBOCK_BB_IRQ, + .max_speed_hz = 120000 /* max sample rate at 3V */ + * 26 /* command + data + overhead */, + .bus_num = 1, + .chip_select = 0, +}, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = -1, @@ -272,6 +348,7 @@ static struct platform_device *devices[] __initdata = { &smc91x_device, &lubbock_flash_device[0], &lubbock_flash_device[1], + &pxa_ssp, }; static struct pxafb_mach_info sharp_lm8v31 __initdata = { @@ -400,6 +477,8 @@ static void __init lubbock_init(void) lubbock_flash_data[flashboot^1].name = "application-flash"; lubbock_flash_data[flashboot].name = "boot-rom"; (void) platform_add_devices(devices, ARRAY_SIZE(devices)); + + spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info)); } static struct map_desc lubbock_io_desc[] __initdata = { @@ -416,6 +495,11 @@ static void __init lubbock_map_io(void) pxa_map_io(); iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc)); + /* SSP data pins */ + pxa_gpio_mode(GPIO23_SCLK_MD); + pxa_gpio_mode(GPIO25_STXD_MD); + pxa_gpio_mode(GPIO26_SRXD_MD); + /* This enables the BTUART */ pxa_gpio_mode(GPIO42_BTRXD_MD); pxa_gpio_mode(GPIO43_BTTXD_MD); diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index 970f98dadff..0c334136db7 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -70,6 +70,18 @@ config ARCH_S3C2440 help Say Y here if you are using the SMDK2440. +config SMDK2440_CPU2440 + bool "SMDK2440 with S3C2440 cpu module" + depends on ARCH_S3C2440 + default y if ARCH_S3C2440 + select CPU_S3C2440 + +config SMDK2440_CPU2442 + bool "SMDM2440 with S3C2442 cpu module" + depends on ARCH_S3C2440 + select CPU_S3C2442 + + config MACH_VR1000 bool "Thorcom VR1000" select CPU_S3C2410 @@ -109,12 +121,26 @@ config CPU_S3C2410 Support for S3C2410 and S3C2410A family from the S3C24XX line of Samsung Mobile CPUs. +config CPU_S3C244X + bool + depends on ARCH_S3C2410 && (CPU_S3C2440 || CPU_S3C2442) + help + Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems. + config CPU_S3C2440 bool depends on ARCH_S3C2410 + select CPU_S3C244X help Support for S3C2440 Samsung Mobile CPU based systems. +config CPU_S3C2442 + bool + depends on ARCH_S3C2420 + select CPU_S3C244X + help + Support for S3C2442 Samsung Mobile CPU based systems. + comment "S3C2410 Boot" config S3C2410_BOOT_WATCHDOG diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile index 3e5712db6b5..5e09355cd4f 100644 --- a/arch/arm/mach-s3c2410/Makefile +++ b/arch/arm/mach-s3c2410/Makefile @@ -24,6 +24,11 @@ obj-$(CONFIG_S3C2410_DMA) += dma.o obj-$(CONFIG_PM) += pm.o sleep.o obj-$(CONFIG_PM_SIMTEC) += pm-simtec.o +# S3C244X support + +obj-$(CONFIG_CPU_S3C244X) += s3c244x.o +obj-$(CONFIG_CPU_S3C244X) += s3c244x-irq.o + # S3C2440 support obj-$(CONFIG_CPU_S3C2440) += s3c2440.o s3c2440-dsc.o @@ -31,6 +36,11 @@ obj-$(CONFIG_CPU_S3C2440) += s3c2440-irq.o obj-$(CONFIG_CPU_S3C2440) += s3c2440-clock.o obj-$(CONFIG_CPU_S3C2440) += s3c2410-gpio.o +# S3C2442 support + +obj-$(CONFIG_CPU_S3C2442) += s3c2442.o +obj-$(CONFIG_CPU_S3C2442) += s3c2442-clock.o + # bast extras obj-$(CONFIG_BAST_PC104_IRQ) += bast-irq.o diff --git a/arch/arm/mach-s3c2410/clock.c b/arch/arm/mach-s3c2410/clock.c index 6de713ad319..99d174612b5 100644 --- a/arch/arm/mach-s3c2410/clock.c +++ b/arch/arm/mach-s3c2410/clock.c @@ -70,7 +70,7 @@ void inline s3c24xx_clk_enable(unsigned int clocks, unsigned int enable) clkcon &= ~clocks; /* ensure none of the special function bits set */ - clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER); + clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER | 3); __raw_writel(clkcon, S3C2410_CLKCON); } diff --git a/arch/arm/mach-s3c2410/common-smdk.c b/arch/arm/mach-s3c2410/common-smdk.c index c940890f621..a40eaa65617 100644 --- a/arch/arm/mach-s3c2410/common-smdk.c +++ b/arch/arm/mach-s3c2410/common-smdk.c @@ -34,6 +34,7 @@ #include <asm/irq.h> #include <asm/arch/regs-gpio.h> +#include <asm/arch/leds-gpio.h> #include <asm/arch/nand.h> @@ -41,6 +42,66 @@ #include "devs.h" #include "pm.h" +/* LED devices */ + +static struct s3c24xx_led_platdata smdk_pdata_led4 = { + .gpio = S3C2410_GPF4, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led4", + .def_trigger = "timer", +}; + +static struct s3c24xx_led_platdata smdk_pdata_led5 = { + .gpio = S3C2410_GPF5, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led5", + .def_trigger = "nand-disk", +}; + +static struct s3c24xx_led_platdata smdk_pdata_led6 = { + .gpio = S3C2410_GPF6, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led6", +}; + +static struct s3c24xx_led_platdata smdk_pdata_led7 = { + .gpio = S3C2410_GPF7, + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .name = "led7", +}; + +static struct platform_device smdk_led4 = { + .name = "s3c24xx_led", + .id = 0, + .dev = { + .platform_data = &smdk_pdata_led4, + }, +}; + +static struct platform_device smdk_led5 = { + .name = "s3c24xx_led", + .id = 1, + .dev = { + .platform_data = &smdk_pdata_led5, + }, +}; + +static struct platform_device smdk_led6 = { + .name = "s3c24xx_led", + .id = 2, + .dev = { + .platform_data = &smdk_pdata_led6, + }, +}; + +static struct platform_device smdk_led7 = { + .name = "s3c24xx_led", + .id = 3, + .dev = { + .platform_data = &smdk_pdata_led7, + }, +}; + /* NAND parititon from 2.4.18-swl5 */ static struct mtd_partition smdk_default_nand_part[] = { @@ -111,6 +172,10 @@ static struct s3c2410_platform_nand smdk_nand_info = { static struct platform_device __initdata *smdk_devs[] = { &s3c_device_nand, + &smdk_led4, + &smdk_led5, + &smdk_led6, + &smdk_led7, }; void __init smdk_machine_init(void) diff --git a/arch/arm/mach-s3c2410/cpu.c b/arch/arm/mach-s3c2410/cpu.c index 70c34fcf785..52842e6e86e 100644 --- a/arch/arm/mach-s3c2410/cpu.c +++ b/arch/arm/mach-s3c2410/cpu.c @@ -37,12 +37,16 @@ #include <asm/mach/map.h> #include <asm/arch/regs-gpio.h> +#include <asm/arch/regs-serial.h> #include "cpu.h" +#include "devs.h" #include "clock.h" #include "s3c2400.h" #include "s3c2410.h" +#include "s3c244x.h" #include "s3c2440.h" +#include "s3c2442.h" struct cpu_table { unsigned long idcode; @@ -59,6 +63,7 @@ struct cpu_table { static const char name_s3c2400[] = "S3C2400"; static const char name_s3c2410[] = "S3C2410"; static const char name_s3c2440[] = "S3C2440"; +static const char name_s3c2442[] = "S3C2442"; static const char name_s3c2410a[] = "S3C2410A"; static const char name_s3c2440a[] = "S3C2440A"; @@ -84,22 +89,31 @@ static struct cpu_table cpu_ids[] __initdata = { { .idcode = 0x32440000, .idmask = 0xffffffff, - .map_io = s3c2440_map_io, - .init_clocks = s3c2440_init_clocks, - .init_uarts = s3c2440_init_uarts, + .map_io = s3c244x_map_io, + .init_clocks = s3c244x_init_clocks, + .init_uarts = s3c244x_init_uarts, .init = s3c2440_init, .name = name_s3c2440 }, { .idcode = 0x32440001, .idmask = 0xffffffff, - .map_io = s3c2440_map_io, - .init_clocks = s3c2440_init_clocks, - .init_uarts = s3c2440_init_uarts, + .map_io = s3c244x_map_io, + .init_clocks = s3c244x_init_clocks, + .init_uarts = s3c244x_init_uarts, .init = s3c2440_init, .name = name_s3c2440a }, { + .idcode = 0x32440aaa, + .idmask = 0xffffffff, + .map_io = s3c244x_map_io, + .init_clocks = s3c244x_init_clocks, + .init_uarts = s3c244x_init_uarts, + .init = s3c2442_init, + .name = name_s3c2442 + }, + { .idcode = 0x0, /* S3C2400 doesn't have an idcode */ .idmask = 0xffffffff, .map_io = s3c2400_map_io, @@ -175,13 +189,13 @@ void __init s3c24xx_init_io(struct map_desc *mach_desc, int size) panic("Unknown S3C24XX CPU"); } + printk("CPU %s (id 0x%08lx)\n", cpu->name, idcode); + if (cpu->map_io == NULL || cpu->init == NULL) { printk(KERN_ERR "CPU %s support not enabled\n", cpu->name); panic("Unsupported S3C24XX CPU"); } - printk("CPU %s (id 0x%08lx)\n", cpu->name, idcode); - (cpu->map_io)(mach_desc, size); } @@ -208,6 +222,49 @@ void __init s3c24xx_init_clocks(int xtal) (cpu->init_clocks)(xtal); } +/* uart management */ + +static int nr_uarts __initdata = 0; + +static struct s3c2410_uartcfg uart_cfgs[3]; + +/* s3c24xx_init_uartdevs + * + * copy the specified platform data and configuration into our central + * set of devices, before the data is thrown away after the init process. + * + * This also fills in the array passed to the serial driver for the + * early initialisation of the console. +*/ + +void __init s3c24xx_init_uartdevs(char *name, + struct s3c24xx_uart_resources *res, + struct s3c2410_uartcfg *cfg, int no) +{ + struct platform_device *platdev; + struct s3c2410_uartcfg *cfgptr = uart_cfgs; + struct s3c24xx_uart_resources *resp; + int uart; + + memcpy(cfgptr, cfg, sizeof(struct s3c2410_uartcfg) * no); + + for (uart = 0; uart < no; uart++, cfg++, cfgptr++) { + platdev = s3c24xx_uart_src[cfgptr->hwport]; + + resp = res + cfgptr->hwport; + + s3c24xx_uart_devs[uart] = platdev; + + platdev->name = name; + platdev->resource = resp->resources; + platdev->num_resources = resp->nr_resources; + + platdev->dev.platform_data = cfgptr; + } + + nr_uarts = no; +} + void __init s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no) { if (cpu == NULL) @@ -232,6 +289,10 @@ static int __init s3c_arch_init(void) if (ret != 0) return ret; + ret = platform_add_devices(s3c24xx_uart_devs, nr_uarts); + if (ret != 0) + return ret; + if (board != NULL) { struct platform_device **ptr = board->devices; int i; diff --git a/arch/arm/mach-s3c2410/cpu.h b/arch/arm/mach-s3c2410/cpu.h index fc1067783f6..40862899b2f 100644 --- a/arch/arm/mach-s3c2410/cpu.h +++ b/arch/arm/mach-s3c2410/cpu.h @@ -31,6 +31,8 @@ #define print_mhz(m) ((m) / MHZ), ((m / 1000) % 1000) /* forward declaration */ +struct s3c24xx_uart_resources; +struct platform_device; struct s3c2410_uartcfg; struct map_desc; @@ -44,6 +46,10 @@ extern void s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no); extern void s3c24xx_init_clocks(int xtal); +extern void s3c24xx_init_uartdevs(char *name, + struct s3c24xx_uart_resources *res, + struct s3c2410_uartcfg *cfg, int no); + /* the board structure is used at first initialsation time * to get info such as the devices to register for this * board. This is done because platfrom_add_devices() cannot @@ -68,3 +74,4 @@ extern struct sys_timer s3c24xx_timer; /* system device classes */ extern struct sysdev_class s3c2440_sysclass; +extern struct sysdev_class s3c2442_sysclass; diff --git a/arch/arm/mach-s3c2410/devs.c b/arch/arm/mach-s3c2410/devs.c index ca09ba516e4..ad3845e329b 100644 --- a/arch/arm/mach-s3c2410/devs.c +++ b/arch/arm/mach-s3c2410/devs.c @@ -38,10 +38,86 @@ #include <asm/arch/regs-serial.h> #include "devs.h" +#include "cpu.h" /* Serial port registrations */ -struct platform_device *s3c24xx_uart_devs[3]; +static struct resource s3c2410_uart0_resource[] = { + [0] = { + .start = S3C2410_PA_UART0, + .end = S3C2410_PA_UART0 + 0x3fff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_S3CUART_RX0, + .end = IRQ_S3CUART_ERR0, + .flags = IORESOURCE_IRQ, + } +}; + +static struct resource s3c2410_uart1_resource[] = { + [0] = { + .start = S3C2410_PA_UART1, + .end = S3C2410_PA_UART1 + 0x3fff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_S3CUART_RX1, + .end = IRQ_S3CUART_ERR1, + .flags = IORESOURCE_IRQ, + } +}; + +static struct resource s3c2410_uart2_resource[] = { + [0] = { + .start = S3C2410_PA_UART2, + .end = S3C2410_PA_UART2 + 0x3fff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_S3CUART_RX2, + .end = IRQ_S3CUART_ERR2, + .flags = IORESOURCE_IRQ, + } +}; + +struct s3c24xx_uart_resources s3c2410_uart_resources[] __initdata = { + [0] = { + .resources = s3c2410_uart0_resource, + .nr_resources = ARRAY_SIZE(s3c2410_uart0_resource), + }, + [1] = { + .resources = s3c2410_uart1_resource, + .nr_resources = ARRAY_SIZE(s3c2410_uart1_resource), + }, + [2] = { + .resources = s3c2410_uart2_resource, + .nr_resources = ARRAY_SIZE(s3c2410_uart2_resource), + }, +}; + +/* yart devices */ + +static struct platform_device s3c24xx_uart_device0 = { + .id = 0, +}; + +static struct platform_device s3c24xx_uart_device1 = { + .id = 1, +}; + +static struct platform_device s3c24xx_uart_device2 = { + .id = 2, +}; + +struct platform_device *s3c24xx_uart_src[3] = { + &s3c24xx_uart_device0, + &s3c24xx_uart_device1, + &s3c24xx_uart_device2, +}; + +struct platform_device *s3c24xx_uart_devs[3] = { +}; /* USB Host Controller */ diff --git a/arch/arm/mach-s3c2410/devs.h b/arch/arm/mach-s3c2410/devs.h index 52c4bab5c76..fa124ed920e 100644 --- a/arch/arm/mach-s3c2410/devs.h +++ b/arch/arm/mach-s3c2410/devs.h @@ -17,7 +17,15 @@ #include <linux/config.h> #include <linux/platform_device.h> +struct s3c24xx_uart_resources { + struct resource *resources; + unsigned long nr_resources; +}; + +extern struct s3c24xx_uart_resources s3c2410_uart_resources[]; + extern struct platform_device *s3c24xx_uart_devs[]; +extern struct platform_device *s3c24xx_uart_src[]; extern struct platform_device s3c_device_usb; extern struct platform_device s3c_device_lcd; diff --git a/arch/arm/mach-s3c2410/mach-anubis.c b/arch/arm/mach-s3c2410/mach-anubis.c index cc97fbf6629..52bf718137d 100644 --- a/arch/arm/mach-s3c2410/mach-anubis.c +++ b/arch/arm/mach-s3c2410/mach-anubis.c @@ -131,7 +131,7 @@ static struct s3c24xx_uart_clksrc anubis_serial_clocks[] = { }; -static struct s3c2410_uartcfg anubis_uartcfgs[] = { +static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c index 995bb8add33..947234df816 100644 --- a/arch/arm/mach-s3c2410/mach-bast.c +++ b/arch/arm/mach-s3c2410/mach-bast.c @@ -208,7 +208,7 @@ static struct s3c24xx_uart_clksrc bast_serial_clocks[] = { }; -static struct s3c2410_uartcfg bast_uartcfgs[] = { +static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index 646a3a5d33a..aec431b2830 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -72,7 +72,7 @@ static struct map_desc h1940_iodesc[] __initdata = { #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE -static struct s3c2410_uartcfg h1940_uartcfgs[] = { +static struct s3c2410_uartcfg h1940_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, diff --git a/arch/arm/mach-s3c2410/mach-nexcoder.c b/arch/arm/mach-s3c2410/mach-nexcoder.c index 07d09509a62..065a1d4e860 100644 --- a/arch/arm/mach-s3c2410/mach-nexcoder.c +++ b/arch/arm/mach-s3c2410/mach-nexcoder.c @@ -51,7 +51,7 @@ static struct map_desc nexcoder_iodesc[] __initdata = { #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB #define UFCON S3C2410_UFCON_RXTRIG12 | S3C2410_UFCON_FIFOMODE -static struct s3c2410_uartcfg nexcoder_uartcfgs[] = { +static struct s3c2410_uartcfg nexcoder_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, diff --git a/arch/arm/mach-s3c2410/mach-osiris.c b/arch/arm/mach-s3c2410/mach-osiris.c index ae078755775..858fd03c6bc 100644 --- a/arch/arm/mach-s3c2410/mach-osiris.c +++ b/arch/arm/mach-s3c2410/mach-osiris.c @@ -95,8 +95,7 @@ static struct s3c24xx_uart_clksrc osiris_serial_clocks[] = { } }; - -static struct s3c2410_uartcfg osiris_uartcfgs[] = { +static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, @@ -107,7 +106,7 @@ static struct s3c2410_uartcfg osiris_uartcfgs[] = { .clocks_size = ARRAY_SIZE(osiris_serial_clocks) }, [1] = { - .hwport = 2, + .hwport = 1, .flags = 0, .ucon = UCON, .ulcon = ULCON, diff --git a/arch/arm/mach-s3c2410/mach-otom.c b/arch/arm/mach-s3c2410/mach-otom.c index b39daedf93c..c71673fd995 100644 --- a/arch/arm/mach-s3c2410/mach-otom.c +++ b/arch/arm/mach-s3c2410/mach-otom.c @@ -45,7 +45,7 @@ static struct map_desc otom11_iodesc[] __initdata = { #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB #define UFCON S3C2410_UFCON_RXTRIG12 | S3C2410_UFCON_FIFOMODE -static struct s3c2410_uartcfg otom11_uartcfgs[] = { +static struct s3c2410_uartcfg otom11_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, diff --git a/arch/arm/mach-s3c2410/mach-smdk2410.c b/arch/arm/mach-s3c2410/mach-smdk2410.c index 2db932d72c5..25f7e9f4dce 100644 --- a/arch/arm/mach-s3c2410/mach-smdk2410.c +++ b/arch/arm/mach-s3c2410/mach-smdk2410.c @@ -65,7 +65,7 @@ static struct map_desc smdk2410_iodesc[] __initdata = { #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE -static struct s3c2410_uartcfg smdk2410_uartcfgs[] = { +static struct s3c2410_uartcfg smdk2410_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, diff --git a/arch/arm/mach-s3c2410/mach-smdk2440.c b/arch/arm/mach-s3c2410/mach-smdk2440.c index 5fffd1d5104..d661c6b7ff5 100644 --- a/arch/arm/mach-s3c2410/mach-smdk2440.c +++ b/arch/arm/mach-s3c2410/mach-smdk2440.c @@ -86,7 +86,7 @@ static struct map_desc smdk2440_iodesc[] __initdata = { #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE -static struct s3c2410_uartcfg smdk2440_uartcfgs[] = { +static struct s3c2410_uartcfg smdk2440_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c index 785fc9cdcf7..d18efb279d3 100644 --- a/arch/arm/mach-s3c2410/mach-vr1000.c +++ b/arch/arm/mach-s3c2410/mach-vr1000.c @@ -166,7 +166,7 @@ static struct s3c24xx_uart_clksrc vr1000_serial_clocks[] = { } }; -static struct s3c2410_uartcfg vr1000_uartcfgs[] = { +static struct s3c2410_uartcfg vr1000_uartcfgs[] __initdata = { [0] = { .hwport = 0, .flags = 0, diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c index fe57d966a34..43e9a550a20 100644 --- a/arch/arm/mach-s3c2410/pm.c +++ b/arch/arm/mach-s3c2410/pm.c @@ -58,7 +58,11 @@ unsigned long s3c_pm_flags; /* cache functions from arch/arm/mm/proc-arm920.S */ +#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH extern void arm920_flush_kern_cache_all(void); +#else +static void arm920_flush_kern_cache_all(void) { } +#endif #define PFX "s3c24xx-pm: " diff --git a/arch/arm/mach-s3c2410/s3c2410.c b/arch/arm/mach-s3c2410/s3c2410.c index 0a2013a7654..0852e87a79c 100644 --- a/arch/arm/mach-s3c2410/s3c2410.c +++ b/arch/arm/mach-s3c2410/s3c2410.c @@ -42,6 +42,7 @@ #include "s3c2410.h" #include "cpu.h" +#include "devs.h" #include "clock.h" /* Initial IO mappings */ @@ -55,93 +56,13 @@ static struct map_desc s3c2410_iodesc[] __initdata = { IODESC_ENT(WATCHDOG), }; -static struct resource s3c_uart0_resource[] = { - [0] = { - .start = S3C2410_PA_UART0, - .end = S3C2410_PA_UART0 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX0, - .end = IRQ_S3CUART_ERR0, - .flags = IORESOURCE_IRQ, - } - -}; - -static struct resource s3c_uart1_resource[] = { - [0] = { - .start = S3C2410_PA_UART1, - .end = S3C2410_PA_UART1 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX1, - .end = IRQ_S3CUART_ERR1, - .flags = IORESOURCE_IRQ, - } -}; - -static struct resource s3c_uart2_resource[] = { - [0] = { - .start = S3C2410_PA_UART2, - .end = S3C2410_PA_UART2 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX2, - .end = IRQ_S3CUART_ERR2, - .flags = IORESOURCE_IRQ, - } -}; - /* our uart devices */ -static struct platform_device s3c_uart0 = { - .name = "s3c2410-uart", - .id = 0, - .num_resources = ARRAY_SIZE(s3c_uart0_resource), - .resource = s3c_uart0_resource, -}; - - -static struct platform_device s3c_uart1 = { - .name = "s3c2410-uart", - .id = 1, - .num_resources = ARRAY_SIZE(s3c_uart1_resource), - .resource = s3c_uart1_resource, -}; - -static struct platform_device s3c_uart2 = { - .name = "s3c2410-uart", - .id = 2, - .num_resources = ARRAY_SIZE(s3c_uart2_resource), - .resource = s3c_uart2_resource, -}; - -static struct platform_device *uart_devices[] __initdata = { - &s3c_uart0, - &s3c_uart1, - &s3c_uart2 -}; - -static int s3c2410_uart_count = 0; - /* uart registration process */ void __init s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no) { - struct platform_device *platdev; - int uart; - - for (uart = 0; uart < no; uart++, cfg++) { - platdev = uart_devices[cfg->hwport]; - - s3c24xx_uart_devs[uart] = platdev; - platdev->dev.platform_data = cfg; - } - - s3c2410_uart_count = uart; + s3c24xx_init_uartdevs("s3c2410-uart", s3c2410_uart_resources, cfg, no); } /* s3c2410_map_io @@ -193,5 +114,5 @@ int __init s3c2410_init(void) { printk("S3C2410: Initialising architecture\n"); - return platform_add_devices(s3c24xx_uart_devs, s3c2410_uart_count); + return 0; } diff --git a/arch/arm/mach-s3c2410/s3c2440-irq.c b/arch/arm/mach-s3c2410/s3c2440-irq.c index 278d0044c85..acfe3870727 100644 --- a/arch/arm/mach-s3c2410/s3c2440-irq.c +++ b/arch/arm/mach-s3c2410/s3c2440-irq.c @@ -100,73 +100,12 @@ static struct irqchip s3c_irq_wdtac97 = { .ack = s3c_irq_wdtac97_ack, }; -/* camera irq */ - -static void s3c_irq_demux_cam(unsigned int irq, - struct irqdesc *desc, - struct pt_regs *regs) -{ - unsigned int subsrc, submsk; - struct irqdesc *mydesc; - - /* read the current pending interrupts, and the mask - * for what it is available */ - - subsrc = __raw_readl(S3C2410_SUBSRCPND); - submsk = __raw_readl(S3C2410_INTSUBMSK); - - subsrc &= ~submsk; - subsrc >>= 11; - subsrc &= 3; - - if (subsrc != 0) { - if (subsrc & 1) { - mydesc = irq_desc + IRQ_S3C2440_CAM_C; - desc_handle_irq(IRQ_S3C2440_CAM_C, mydesc, regs); - } - if (subsrc & 2) { - mydesc = irq_desc + IRQ_S3C2440_CAM_P; - desc_handle_irq(IRQ_S3C2440_CAM_P, mydesc, regs); - } - } -} - -#define INTMSK_CAM (1UL << (IRQ_CAM - IRQ_EINT0)) - -static void -s3c_irq_cam_mask(unsigned int irqno) -{ - s3c_irqsub_mask(irqno, INTMSK_CAM, 3<<11); -} - -static void -s3c_irq_cam_unmask(unsigned int irqno) -{ - s3c_irqsub_unmask(irqno, INTMSK_CAM); -} - -static void -s3c_irq_cam_ack(unsigned int irqno) -{ - s3c_irqsub_maskack(irqno, INTMSK_CAM, 3<<11); -} - -static struct irqchip s3c_irq_cam = { - .mask = s3c_irq_cam_mask, - .unmask = s3c_irq_cam_unmask, - .ack = s3c_irq_cam_ack, -}; - static int s3c2440_irq_add(struct sys_device *sysdev) { unsigned int irqno; printk("S3C2440: IRQ Support\n"); - set_irq_chip(IRQ_NFCON, &s3c_irq_level_chip); - set_irq_handler(IRQ_NFCON, do_level_IRQ); - set_irq_flags(IRQ_NFCON, IRQF_VALID); - /* add new chained handler for wdt, ac7 */ set_irq_chip(IRQ_WDT, &s3c_irq_level_chip); @@ -179,18 +118,6 @@ static int s3c2440_irq_add(struct sys_device *sysdev) set_irq_flags(irqno, IRQF_VALID); } - /* add chained handler for camera */ - - set_irq_chip(IRQ_CAM, &s3c_irq_level_chip); - set_irq_handler(IRQ_CAM, do_level_IRQ); - set_irq_chained_handler(IRQ_CAM, s3c_irq_demux_cam); - - for (irqno = IRQ_S3C2440_CAM_C; irqno <= IRQ_S3C2440_CAM_P; irqno++) { - set_irq_chip(irqno, &s3c_irq_cam); - set_irq_handler(irqno, do_level_IRQ); - set_irq_flags(irqno, IRQF_VALID); - } - return 0; } @@ -198,10 +125,10 @@ static struct sysdev_driver s3c2440_irq_driver = { .add = s3c2440_irq_add, }; -static int s3c24xx_irq_driver(void) +static int s3c2440_irq_init(void) { return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_irq_driver); } -arch_initcall(s3c24xx_irq_driver); +arch_initcall(s3c2440_irq_init); diff --git a/arch/arm/mach-s3c2410/s3c2440.c b/arch/arm/mach-s3c2410/s3c2440.c index b7fe6d9453f..0ab50f44f31 100644 --- a/arch/arm/mach-s3c2410/s3c2440.c +++ b/arch/arm/mach-s3c2410/s3c2440.c @@ -1,6 +1,6 @@ /* linux/arch/arm/mach-s3c2410/s3c2440.c * - * Copyright (c) 2004-2005 Simtec Electronics + * Copyright (c) 2004-2006 Simtec Electronics * Ben Dooks <ben@simtec.co.uk> * * Samsung S3C2440 Mobile CPU support @@ -8,16 +8,6 @@ * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. - * - * Modifications: - * 24-Aug-2004 BJD Start of s3c2440 support - * 12-Oct-2004 BJD Moved clock info out to clock.c - * 01-Nov-2004 BJD Fixed clock build code - * 09-Nov-2004 BJD Added sysdev for power management - * 04-Nov-2004 BJD New serial registration - * 15-Nov-2004 BJD Rename the i2c device for the s3c2440 - * 14-Jan-2005 BJD Moved clock init code into seperate function - * 14-Jan-2005 BJD Removed un-used clock bits */ #include <linux/kernel.h> @@ -50,234 +40,20 @@ #include "cpu.h" #include "pm.h" - -static struct map_desc s3c2440_iodesc[] __initdata = { - IODESC_ENT(USBHOST), - IODESC_ENT(CLKPWR), - IODESC_ENT(LCD), - IODESC_ENT(TIMER), - IODESC_ENT(ADC), - IODESC_ENT(WATCHDOG), -}; - -static struct resource s3c_uart0_resource[] = { - [0] = { - .start = S3C2410_PA_UART0, - .end = S3C2410_PA_UART0 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX0, - .end = IRQ_S3CUART_ERR0, - .flags = IORESOURCE_IRQ, - } - -}; - -static struct resource s3c_uart1_resource[] = { - [0] = { - .start = S3C2410_PA_UART1, - .end = S3C2410_PA_UART1 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX1, - .end = IRQ_S3CUART_ERR1, - .flags = IORESOURCE_IRQ, - } -}; - -static struct resource s3c_uart2_resource[] = { - [0] = { - .start = S3C2410_PA_UART2, - .end = S3C2410_PA_UART2 + 0x3fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_S3CUART_RX2, - .end = IRQ_S3CUART_ERR2, - .flags = IORESOURCE_IRQ, - } -}; - -/* our uart devices */ - -static struct platform_device s3c_uart0 = { - .name = "s3c2440-uart", - .id = 0, - .num_resources = ARRAY_SIZE(s3c_uart0_resource), - .resource = s3c_uart0_resource, -}; - -static struct platform_device s3c_uart1 = { - .name = "s3c2440-uart", - .id = 1, - .num_resources = ARRAY_SIZE(s3c_uart1_resource), - .resource = s3c_uart1_resource, -}; - -static struct platform_device s3c_uart2 = { - .name = "s3c2440-uart", - .id = 2, - .num_resources = ARRAY_SIZE(s3c_uart2_resource), - .resource = s3c_uart2_resource, -}; - -static struct platform_device *uart_devices[] __initdata = { - &s3c_uart0, - &s3c_uart1, - &s3c_uart2 -}; - -/* uart initialisation */ - -static int __initdata s3c2440_uart_count; - -void __init s3c2440_init_uarts(struct s3c2410_uartcfg *cfg, int no) -{ - struct platform_device *platdev; - int uart; - - for (uart = 0; uart < no; uart++, cfg++) { - platdev = uart_devices[cfg->hwport]; - - s3c24xx_uart_devs[uart] = platdev; - platdev->dev.platform_data = cfg; - } - - s3c2440_uart_count = uart; -} - - -#ifdef CONFIG_PM - -static struct sleep_save s3c2440_sleep[] = { - SAVE_ITEM(S3C2440_DSC0), - SAVE_ITEM(S3C2440_DSC1), - SAVE_ITEM(S3C2440_GPJDAT), - SAVE_ITEM(S3C2440_GPJCON), - SAVE_ITEM(S3C2440_GPJUP) -}; - -static int s3c2440_suspend(struct sys_device *dev, pm_message_t state) -{ - s3c2410_pm_do_save(s3c2440_sleep, ARRAY_SIZE(s3c2440_sleep)); - return 0; -} - -static int s3c2440_resume(struct sys_device *dev) -{ - s3c2410_pm_do_restore(s3c2440_sleep, ARRAY_SIZE(s3c2440_sleep)); - return 0; -} - -#else -#define s3c2440_suspend NULL -#define s3c2440_resume NULL -#endif - -struct sysdev_class s3c2440_sysclass = { - set_kset_name("s3c2440-core"), - .suspend = s3c2440_suspend, - .resume = s3c2440_resume -}; - static struct sys_device s3c2440_sysdev = { .cls = &s3c2440_sysclass, }; -void __init s3c2440_map_io(struct map_desc *mach_desc, int size) +int __init s3c2440_init(void) { - /* register our io-tables */ - - iotable_init(s3c2440_iodesc, ARRAY_SIZE(s3c2440_iodesc)); - iotable_init(mach_desc, size); - - /* rename any peripherals used differing from the s3c2410 */ - - s3c_device_i2c.name = "s3c2440-i2c"; - s3c_device_nand.name = "s3c2440-nand"; + printk("S3C2440: Initialising architecture\n"); /* change irq for watchdog */ s3c_device_wdt.resource[1].start = IRQ_S3C2440_WDT; s3c_device_wdt.resource[1].end = IRQ_S3C2440_WDT; -} - -void __init s3c2440_init_clocks(int xtal) -{ - unsigned long clkdiv; - unsigned long camdiv; - unsigned long hclk, fclk, pclk; - int hdiv = 1; - - /* now we've got our machine bits initialised, work out what - * clocks we've got */ - - fclk = s3c2410_get_pll(__raw_readl(S3C2410_MPLLCON), xtal) * 2; - - clkdiv = __raw_readl(S3C2410_CLKDIVN); - camdiv = __raw_readl(S3C2440_CAMDIVN); - - /* work out clock scalings */ - - switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) { - case S3C2440_CLKDIVN_HDIVN_1: - hdiv = 1; - break; - - case S3C2440_CLKDIVN_HDIVN_2: - hdiv = 2; - break; - - case S3C2440_CLKDIVN_HDIVN_4_8: - hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4; - break; - - case S3C2440_CLKDIVN_HDIVN_3_6: - hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3; - break; - } - - hclk = fclk / hdiv; - pclk = hclk / ((clkdiv & S3C2440_CLKDIVN_PDIVN)? 2:1); - - /* print brief summary of clocks, etc */ - - printk("S3C2440: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", - print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); - - /* initialise the clocks here, to allow other things like the - * console to use them, and to add new ones after the initialisation - */ - - s3c24xx_setup_clocks(xtal, fclk, hclk, pclk); -} - -/* need to register class before we actually register the device, and - * we also need to ensure that it has been initialised before any of the - * drivers even try to use it (even if not on an s3c2440 based system) - * as a driver which may support both 2410 and 2440 may try and use it. -*/ - -static int __init s3c2440_core_init(void) -{ - return sysdev_class_register(&s3c2440_sysclass); -} - -core_initcall(s3c2440_core_init); - -int __init s3c2440_init(void) -{ - int ret; - - printk("S3C2440: Initialising architecture\n"); - ret = sysdev_register(&s3c2440_sysdev); - if (ret != 0) - printk(KERN_ERR "failed to register sysdev for s3c2440\n"); - else - ret = platform_add_devices(s3c24xx_uart_devs, s3c2440_uart_count); + /* register our system device for everything else */ - return ret; + return sysdev_register(&s3c2440_sysdev); } diff --git a/arch/arm/mach-s3c2410/s3c2442-clock.c b/arch/arm/mach-s3c2410/s3c2442-clock.c new file mode 100644 index 00000000000..5b7b301eb52 --- /dev/null +++ b/arch/arm/mach-s3c2410/s3c2442-clock.c @@ -0,0 +1,171 @@ +/* linux/arch/arm/mach-s3c2410/s3c2442-clock.c + * + * Copyright (c) 2004-2005 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C2442 Clock support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/errno.h> +#include <linux/err.h> +#include <linux/device.h> +#include <linux/sysdev.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/mutex.h> +#include <linux/clk.h> + +#include <asm/hardware.h> +#include <asm/atomic.h> +#include <asm/irq.h> +#include <asm/io.h> + +#include <asm/arch/regs-clock.h> + +#include "clock.h" +#include "cpu.h" + +/* S3C2442 extended clock support */ + +static unsigned long s3c2442_camif_upll_round(struct clk *clk, + unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + int div; + + if (rate > parent_rate) + return parent_rate; + + div = parent_rate / rate; + + if (div == 3) + return parent_rate / 3; + + /* note, we remove the +/- 1 calculations for the divisor */ + + div /= 2; + + if (div < 1) + div = 1; + else if (div > 16) + div = 16; + + return parent_rate / (div * 2); +} + +static int s3c2442_camif_upll_setrate(struct clk *clk, unsigned long rate) +{ + unsigned long parent_rate = clk_get_rate(clk->parent); + unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); + + rate = s3c2442_camif_upll_round(clk, rate); + + camdivn &= ~S3C2442_CAMDIVN_CAMCLK_DIV3; + + if (rate == parent_rate) { + camdivn &= ~S3C2440_CAMDIVN_CAMCLK_SEL; + } else if ((parent_rate / rate) == 3) { + camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; + camdivn |= S3C2442_CAMDIVN_CAMCLK_DIV3; + } else { + camdivn &= ~S3C2440_CAMDIVN_CAMCLK_MASK; + camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; + camdivn |= (((parent_rate / rate) / 2) - 1); + } + + __raw_writel(camdivn, S3C2440_CAMDIVN); + + return 0; +} + +/* Extra S3C2442 clocks */ + +static struct clk s3c2442_clk_cam = { + .name = "camif", + .id = -1, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2440_CLKCON_CAMERA, +}; + +static struct clk s3c2442_clk_cam_upll = { + .name = "camif-upll", + .id = -1, + .set_rate = s3c2442_camif_upll_setrate, + .round_rate = s3c2442_camif_upll_round, +}; + +static int s3c2442_clk_add(struct sys_device *sysdev) +{ + unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); + unsigned long clkdivn; + struct clk *clk_h; + struct clk *clk_p; + struct clk *clk_upll; + + printk("S3C2442: Clock Support, DVS %s\n", + (camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off"); + + clk_p = clk_get(NULL, "pclk"); + clk_h = clk_get(NULL, "hclk"); + clk_upll = clk_get(NULL, "upll"); + + if (IS_ERR(clk_p) || IS_ERR(clk_h) || IS_ERR(clk_upll)) { + printk(KERN_ERR "S3C2442: Failed to get parent clocks\n"); + return -EINVAL; + } + + /* check rate of UPLL, and if it is near 96MHz, then change + * to using half the UPLL rate for the system */ + + if (clk_get_rate(clk_upll) > (94 * MHZ)) { + clk_usb_bus.rate = clk_get_rate(clk_upll) / 2; + + mutex_lock(&clocks_mutex); + + clkdivn = __raw_readl(S3C2410_CLKDIVN); + clkdivn |= S3C2440_CLKDIVN_UCLK; + __raw_writel(clkdivn, S3C2410_CLKDIVN); + + mutex_unlock(&clocks_mutex); + } + + s3c2442_clk_cam.parent = clk_h; + s3c2442_clk_cam_upll.parent = clk_upll; + + s3c24xx_register_clock(&s3c2442_clk_cam); + s3c24xx_register_clock(&s3c2442_clk_cam_upll); + + clk_disable(&s3c2442_clk_cam); + + return 0; +} + +static struct sysdev_driver s3c2442_clk_driver = { + .add = s3c2442_clk_add, +}; + +static __init int s3c2442_clk_init(void) +{ + return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_clk_driver); +} + +arch_initcall(s3c2442_clk_init); diff --git a/arch/arm/mach-s3c2410/s3c2442.c b/arch/arm/mach-s3c2410/s3c2442.c new file mode 100644 index 00000000000..debae243055 --- /dev/null +++ b/arch/arm/mach-s3c2410/s3c2442.c @@ -0,0 +1,52 @@ +/* linux/arch/arm/mach-s3c2410/s3c2440.c + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * Samsung S3C2442 Mobile CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/sysdev.h> +#include <linux/clk.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/irq.h> + +#include <asm/arch/regs-clock.h> +#include <asm/arch/regs-serial.h> +#include <asm/arch/regs-gpio.h> +#include <asm/arch/regs-gpioj.h> +#include <asm/arch/regs-dsc.h> + +#include "s3c2442.h" +#include "clock.h" +#include "devs.h" +#include "cpu.h" +#include "pm.h" + +static struct sys_device s3c2442_sysdev = { + .cls = &s3c2442_sysclass, +}; + +int __init s3c2442_init(void) +{ + printk("S3C2442: Initialising architecture\n"); + + return sysdev_register(&s3c2442_sysdev); +} diff --git a/arch/arm/mach-s3c2410/s3c2442.h b/arch/arm/mach-s3c2410/s3c2442.h new file mode 100644 index 00000000000..0ae37d24866 --- /dev/null +++ b/arch/arm/mach-s3c2410/s3c2442.h @@ -0,0 +1,17 @@ +/* arch/arm/mach-s3c2410/s3c2442.h + * + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * Header file for s3c2442 cpu support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifdef CONFIG_CPU_S3C2442 +extern int s3c2442_init(void); +#else +#define s3c2442_init NULL +#endif diff --git a/arch/arm/mach-s3c2410/s3c244x-irq.c b/arch/arm/mach-s3c2410/s3c244x-irq.c new file mode 100644 index 00000000000..2aadca1ce7e --- /dev/null +++ b/arch/arm/mach-s3c2410/s3c244x-irq.c @@ -0,0 +1,142 @@ +/* linux/arch/arm/mach-s3c2410/s3c2440-irq.c + * + * Copyright (c) 2003,2004 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Changelog: + * 25-Jul-2005 BJD Split from irq.c + * +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/ptrace.h> +#include <linux/sysdev.h> + +#include <asm/hardware.h> +#include <asm/irq.h> +#include <asm/io.h> + +#include <asm/mach/irq.h> + +#include <asm/arch/regs-irq.h> +#include <asm/arch/regs-gpio.h> + +#include "cpu.h" +#include "pm.h" +#include "irq.h" + +/* camera irq */ + +static void s3c_irq_demux_cam(unsigned int irq, + struct irqdesc *desc, + struct pt_regs *regs) +{ + unsigned int subsrc, submsk; + struct irqdesc *mydesc; + + /* read the current pending interrupts, and the mask + * for what it is available */ + + subsrc = __raw_readl(S3C2410_SUBSRCPND); + submsk = __raw_readl(S3C2410_INTSUBMSK); + + subsrc &= ~submsk; + subsrc >>= 11; + subsrc &= 3; + + if (subsrc != 0) { + if (subsrc & 1) { + mydesc = irq_desc + IRQ_S3C2440_CAM_C; + desc_handle_irq(IRQ_S3C2440_CAM_C, mydesc, regs); + } + if (subsrc & 2) { + mydesc = irq_desc + IRQ_S3C2440_CAM_P; + desc_handle_irq(IRQ_S3C2440_CAM_P, mydesc, regs); + } + } +} + +#define INTMSK_CAM (1UL << (IRQ_CAM - IRQ_EINT0)) + +static void +s3c_irq_cam_mask(unsigned int irqno) +{ + s3c_irqsub_mask(irqno, INTMSK_CAM, 3<<11); +} + +static void +s3c_irq_cam_unmask(unsigned int irqno) +{ + s3c_irqsub_unmask(irqno, INTMSK_CAM); +} + +static void +s3c_irq_cam_ack(unsigned int irqno) +{ + s3c_irqsub_maskack(irqno, INTMSK_CAM, 3<<11); +} + +static struct irqchip s3c_irq_cam = { + .mask = s3c_irq_cam_mask, + .unmask = s3c_irq_cam_unmask, + .ack = s3c_irq_cam_ack, +}; + +static int s3c244x_irq_add(struct sys_device *sysdev) +{ + unsigned int irqno; + + set_irq_chip(IRQ_NFCON, &s3c_irq_level_chip); + set_irq_handler(IRQ_NFCON, do_level_IRQ); + set_irq_flags(IRQ_NFCON, IRQF_VALID); + + /* add chained handler for camera */ + + set_irq_chip(IRQ_CAM, &s3c_irq_level_chip); + set_irq_handler(IRQ_CAM, do_level_IRQ); + set_irq_chained_handler(IRQ_CAM, s3c_irq_demux_cam); + + for (irqno = IRQ_S3C2440_CAM_C; irqno <= IRQ_S3C2440_CAM_P; irqno++) { + set_irq_chip(irqno, &s3c_irq_cam); + set_irq_handler(irqno, do_level_IRQ); + set_irq_flags(irqno, IRQF_VALID); + } + + return 0; +} + +static struct sysdev_driver s3c244x_irq_driver = { + .add = s3c244x_irq_add, +}; + +static int s3c2440_irq_init(void) +{ + return sysdev_driver_register(&s3c2440_sysclass, &s3c244x_irq_driver); +} + +arch_initcall(s3c2440_irq_init); + + +static int s3c2442_irq_init(void) +{ + return sysdev_driver_register(&s3c2442_sysclass, &s3c244x_irq_driver); +} + +arch_initcall(s3c2442_irq_init); diff --git a/arch/arm/mach-s3c2410/s3c244x.c b/arch/arm/mach-s3c2410/s3c244x.c new file mode 100644 index 00000000000..96852a7000d --- /dev/null +++ b/arch/arm/mach-s3c2410/s3c244x.c @@ -0,0 +1,182 @@ +/* linux/arch/arm/mach-s3c2410/s3c244x.c + * + * Copyright (c) 2004-2006 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * Samsung S3C2440 and S3C2442 Mobile CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/timer.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/sysdev.h> +#include <linux/clk.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/irq.h> + +#include <asm/arch/regs-clock.h> +#include <asm/arch/regs-serial.h> +#include <asm/arch/regs-gpio.h> +#include <asm/arch/regs-gpioj.h> +#include <asm/arch/regs-dsc.h> + +#include "s3c2440.h" +#include "s3c244x.h" +#include "clock.h" +#include "devs.h" +#include "cpu.h" +#include "pm.h" + +static struct map_desc s3c244x_iodesc[] __initdata = { + IODESC_ENT(CLKPWR), + IODESC_ENT(TIMER), + IODESC_ENT(WATCHDOG), + IODESC_ENT(LCD), + IODESC_ENT(ADC), + IODESC_ENT(USBHOST), +}; + +/* uart initialisation */ + +void __init s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no) +{ + s3c24xx_init_uartdevs("s3c2440-uart", s3c2410_uart_resources, cfg, no); +} + +void __init s3c244x_map_io(struct map_desc *mach_desc, int size) +{ + /* register our io-tables */ + + iotable_init(s3c244x_iodesc, ARRAY_SIZE(s3c244x_iodesc)); + iotable_init(mach_desc, size); + + /* rename any peripherals used differing from the s3c2410 */ + + s3c_device_i2c.name = "s3c2440-i2c"; + s3c_device_nand.name = "s3c2440-nand"; +} + +void __init s3c244x_init_clocks(int xtal) +{ + unsigned long clkdiv; + unsigned long camdiv; + unsigned long hclk, fclk, pclk; + int hdiv = 1; + + /* now we've got our machine bits initialised, work out what + * clocks we've got */ + + fclk = s3c2410_get_pll(__raw_readl(S3C2410_MPLLCON), xtal) * 2; + + clkdiv = __raw_readl(S3C2410_CLKDIVN); + camdiv = __raw_readl(S3C2440_CAMDIVN); + + /* work out clock scalings */ + + switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) { + case S3C2440_CLKDIVN_HDIVN_1: + hdiv = 1; + break; + + case S3C2440_CLKDIVN_HDIVN_2: + hdiv = 2; + break; + + case S3C2440_CLKDIVN_HDIVN_4_8: + hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4; + break; + + case S3C2440_CLKDIVN_HDIVN_3_6: + hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3; + break; + } + + hclk = fclk / hdiv; + pclk = hclk / ((clkdiv & S3C2440_CLKDIVN_PDIVN)? 2:1); + + /* print brief summary of clocks, etc */ + + printk("S3C244X: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", + print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); + + /* initialise the clocks here, to allow other things like the + * console to use them, and to add new ones after the initialisation + */ + + s3c24xx_setup_clocks(xtal, fclk, hclk, pclk); +} + +#ifdef CONFIG_PM + +static struct sleep_save s3c244x_sleep[] = { + SAVE_ITEM(S3C2440_DSC0), + SAVE_ITEM(S3C2440_DSC1), + SAVE_ITEM(S3C2440_GPJDAT), + SAVE_ITEM(S3C2440_GPJCON), + SAVE_ITEM(S3C2440_GPJUP) +}; + +static int s3c244x_suspend(struct sys_device *dev, pm_message_t state) +{ + s3c2410_pm_do_save(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep)); + return 0; +} + +static int s3c244x_resume(struct sys_device *dev) +{ + s3c2410_pm_do_restore(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep)); + return 0; +} + +#else +#define s3c244x_suspend NULL +#define s3c244x_resume NULL +#endif + +/* Since the S3C2442 and S3C2440 share items, put both sysclasses here */ + +struct sysdev_class s3c2440_sysclass = { + set_kset_name("s3c2440-core"), + .suspend = s3c244x_suspend, + .resume = s3c244x_resume +}; + +struct sysdev_class s3c2442_sysclass = { + set_kset_name("s3c2442-core"), + .suspend = s3c244x_suspend, + .resume = s3c244x_resume +}; + +/* need to register class before we actually register the device, and + * we also need to ensure that it has been initialised before any of the + * drivers even try to use it (even if not on an s3c2440 based system) + * as a driver which may support both 2410 and 2440 may try and use it. +*/ + +static int __init s3c2440_core_init(void) +{ + return sysdev_class_register(&s3c2440_sysclass); +} + +core_initcall(s3c2440_core_init); + +static int __init s3c2442_core_init(void) +{ + return sysdev_class_register(&s3c2442_sysclass); +} + +core_initcall(s3c2442_core_init); diff --git a/arch/arm/mach-s3c2410/s3c244x.h b/arch/arm/mach-s3c2410/s3c244x.h new file mode 100644 index 00000000000..3e7f5f75134 --- /dev/null +++ b/arch/arm/mach-s3c2410/s3c244x.h @@ -0,0 +1,25 @@ +/* arch/arm/mach-s3c2410/s3c2440.h + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * Header file for S3C2440 and S3C2442 cpu support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) + +extern void s3c244x_map_io(struct map_desc *mach_desc, int size); + +extern void s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no); + +extern void s3c244x_init_clocks(int xtal); + +#else +#define s3c244x_init_clocks NULL +#define s3c244x_init_uarts NULL +#define s3c244x_map_io NULL +#endif diff --git a/arch/arm/mach-s3c2410/sleep.S b/arch/arm/mach-s3c2410/sleep.S index 73de2eaca22..5f6761ed96b 100644 --- a/arch/arm/mach-s3c2410/sleep.S +++ b/arch/arm/mach-s3c2410/sleep.S @@ -66,7 +66,9 @@ ENTRY(s3c2410_cpu_suspend) @@ flush the caches to ensure everything is back out to @@ SDRAM before the core powers down +#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH bl arm920_flush_kern_cache_all +#endif @@ prepare cpu to sleep diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index c55b739e10b..1ff2f073a55 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -121,8 +121,8 @@ config CPU_ARM925T # ARM926T config CPU_ARM926T bool "Support ARM926T processor" - depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB - default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX + depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 + default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 select CPU_32v5 select CPU_ABRT_EV5TJ select CPU_CACHE_VIVT diff --git a/drivers/net/smc91x.h b/drivers/net/smc91x.h index f72a4f57905..bf776125ca3 100644 --- a/drivers/net/smc91x.h +++ b/drivers/net/smc91x.h @@ -260,15 +260,17 @@ SMC_outw(u16 val, void __iomem *ioaddr, int reg) #define RPC_LSA_DEFAULT RPC_LED_TX_RX #define RPC_LSB_DEFAULT RPC_LED_100_10 -#elif defined(CONFIG_MACH_LPD7A400) || defined(CONFIG_MACH_LPD7A404) +#elif defined(CONFIG_MACH_LPD79520) \ + || defined(CONFIG_MACH_LPD7A400) \ + || defined(CONFIG_MACH_LPD7A404) -/* The LPD7A40X_IOBARRIER is necessary to overcome a mismatch between - * the way that the CPU handles chip selects and the way that the SMC - * chip expects the chip select to operate. Refer to +/* The LPD7X_IOBARRIER is necessary to overcome a mismatch between the + * way that the CPU handles chip selects and the way that the SMC chip + * expects the chip select to operate. Refer to * Documentation/arm/Sharp-LH/IOBarrier for details. The read from - * IOBARRIER is a byte as a least-common denominator of possible - * regions to use as the barrier. It would be wasteful to read 32 - * bits from a byte oriented region. + * IOBARRIER is a byte, in order that we read the least-common + * denominator. It would be wasteful to read 32 bits from an 8-bit + * accessible region. * * There is no explicit protection against interrupts intervening * between the writew and the IOBARRIER. In SMC ISR there is a @@ -287,25 +289,35 @@ SMC_outw(u16 val, void __iomem *ioaddr, int reg) #define SMC_CAN_USE_16BIT 1 #define SMC_CAN_USE_32BIT 0 #define SMC_NOWAIT 0 -#define LPD7A40X_IOBARRIER readb (IOBARRIER_VIRT) +#define LPD7X_IOBARRIER readb (IOBARRIER_VIRT) -#define SMC_inw(a,r) readw ((void*) ((a) + (r))) -#define SMC_insw(a,r,p,l) readsw ((void*) ((a) + (r)), p, l) -#define SMC_outw(v,a,r) ({ writew ((v), (a) + (r)); LPD7A40X_IOBARRIER; }) +#define SMC_inw(a,r)\ + ({ unsigned short v = readw ((void*) ((a) + (r))); LPD7X_IOBARRIER; v; }) +#define SMC_outw(v,a,r) ({ writew ((v), (a) + (r)); LPD7X_IOBARRIER; }) -#define SMC_outsw LPD7A40X_SMC_outsw +#define SMC_insw LPD7_SMC_insw +static inline void LPD7_SMC_insw (unsigned char* a, int r, + unsigned char* p, int l) +{ + unsigned short* ps = (unsigned short*) p; + while (l-- > 0) { + *ps++ = readw (a + r); + LPD7X_IOBARRIER; + } +} -static inline void LPD7A40X_SMC_outsw(unsigned long a, int r, - unsigned char* p, int l) +#define SMC_outsw LPD7_SMC_outsw +static inline void LPD7_SMC_outsw (unsigned char* a, int r, + unsigned char* p, int l) { unsigned short* ps = (unsigned short*) p; while (l-- > 0) { writew (*ps++, a + r); - LPD7A40X_IOBARRIER; + LPD7X_IOBARRIER; } } -#define SMC_INTERRUPT_PREAMBLE LPD7A40X_IOBARRIER +#define SMC_INTERRUPT_PREAMBLE LPD7X_IOBARRIER #define RPC_LSA_DEFAULT RPC_LED_TX_RX #define RPC_LSB_DEFAULT RPC_LED_100_10 diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c index f5aac92fb79..53c2465bad2 100644 --- a/drivers/serial/s3c2410.c +++ b/drivers/serial/s3c2410.c @@ -1365,7 +1365,7 @@ static inline void s3c2410_serial_exit(void) #endif /* CONFIG_CPU_S3C2410 */ -#ifdef CONFIG_CPU_S3C2440 +#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) static int s3c2440_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *clk) diff --git a/drivers/serial/serial_lh7a40x.c b/drivers/serial/serial_lh7a40x.c index aa521b8e0d4..776d4ff0608 100644 --- a/drivers/serial/serial_lh7a40x.c +++ b/drivers/serial/serial_lh7a40x.c @@ -145,14 +145,15 @@ lh7a40xuart_rx_chars (struct uart_port* port) { struct tty_struct* tty = port->info->tty; int cbRxMax = 256; /* (Gross) limit on receive */ - unsigned int data, flag;/* Received data and status */ + unsigned int data; /* Received data and status */ + unsigned int flag; while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) { data = UR (port, UART_R_DATA); flag = TTY_NORMAL; ++port->icount.rx; - if (unlikely(data & RxError)) { /* Quick check, short-circuit */ + if (unlikely(data & RxError)) { if (data & RxBreak) { data &= ~(RxFramingError | RxParityError); ++port->icount.brk; @@ -303,7 +304,7 @@ static void lh7a40xuart_set_mctrl (struct uart_port* port, unsigned int mctrl) /* Note, kernel appears to be setting DTR and RTS on console. */ /* *** FIXME: this deserves more work. There's some work in - tracing all of the IO pins. */ + tracing all of the IO pins. */ #if 0 if( port->mapbase == UART1_PHYS) { gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS); @@ -662,9 +663,13 @@ static int __init lh7a40xuart_init(void) if (ret == 0) { int i; - for (i = 0; i < DEV_NR; i++) + for (i = 0; i < DEV_NR; i++) { + /* UART3, when used, requires GPIO pin reallocation */ + if (lh7a40x_ports[i].port.mapbase == UART3_PHYS) + GPIO_PINMUX |= 1<<3; uart_add_one_port (&lh7a40x_reg, &lh7a40x_ports[i].port); + } } return ret; } diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index 5641498725d..5a2840aeb54 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -167,6 +167,69 @@ config FB_ARMCLCD here and read <file:Documentation/modules.txt>. The module will be called amba-clcd. +choice + + depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X) + prompt "LCD Panel" + default FB_ARMCLCD_SHARP_LQ035Q7DB02 + +config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT + bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC" + help + This is an implementation of the Sharp LQ035Q7DB02, a 3.5" + color QVGA, HRTFT panel. The LogicPD device includes an + an integrated HRTFT controller IC. + The native resolution is 240x320. + +config FB_ARMCLCD_SHARP_LQ057Q3DC02 + bool "LogicPD LCD 5.7\" QVGA" + help + This is an implementation of the Sharp LQ057Q3DC02, a 5.7" + color QVGA, TFT panel. The LogicPD device includes an + The native resolution is 320x240. + +config FB_ARMCLCD_SHARP_LQ64D343 + bool "LogicPD LCD 6.4\" VGA" + help + This is an implementation of the Sharp LQ64D343, a 6.4" + color VGA, TFT panel. The LogicPD device includes an + The native resolution is 640x480. + +config FB_ARMCLCD_SHARP_LQ10D368 + bool "LogicPD LCD 10.4\" VGA" + help + This is an implementation of the Sharp LQ10D368, a 10.4" + color VGA, TFT panel. The LogicPD device includes an + The native resolution is 640x480. + + +config FB_ARMCLCD_SHARP_LQ121S1DG41 + bool "LogicPD LCD 12.1\" SVGA" + help + This is an implementation of the Sharp LQ121S1DG41, a 12.1" + color SVGA, TFT panel. The LogicPD device includes an + The native resolution is 800x600. + + This panel requires a clock rate may be an integer fraction + of the base LCDCLK frequency. The driver will select the + highest frequency available that is lower than the maximum + allowed. The panel may flicker if the clock rate is + slower than the recommended minimum. + +config FB_ARMCLCD_AUO_A070VW01_WIDE + bool "AU Optronics A070VW01 LCD 7.0\" WIDE" + help + This is an implementation of the AU Optronics, a 7.0" + WIDE Color. The native resolution is 234x480. + +config FB_ARMCLCD_HITACHI + bool "Hitachi Wide Screen 800x480" + help + This is an implementation of the Hitachi 800x480. + +endchoice + + config FB_ACORN bool "Acorn VIDC support" depends on (FB = y) && ARM && (ARCH_ACORN || ARCH_CLPS7500) diff --git a/include/asm-arm/arch-lh7a40x/clocks.h b/include/asm-arm/arch-lh7a40x/clocks.h new file mode 100644 index 00000000000..bee02fd8dab --- /dev/null +++ b/include/asm-arm/arch-lh7a40x/clocks.h @@ -0,0 +1,20 @@ +/* include/asm-arm/arch-lh7a40x/clocks.h + * + * Copyright (C) 2004 Marc Singer + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + */ + +#include <linux/config.h> + +#ifndef __ASM_ARCH_CLOCKS_H +#define __ASM_ARCH_CLOCKS_H + +unsigned int fclkfreq_get (void); +unsigned int hclkfreq_get (void); +unsigned int pclkfreq_get (void); + +#endif /* _ASM_ARCH_CLOCKS_H */ diff --git a/include/asm-arm/arch-lh7a40x/constants.h b/include/asm-arm/arch-lh7a40x/constants.h index 52c1cb9c39c..2929e891ee0 100644 --- a/include/asm-arm/arch-lh7a40x/constants.h +++ b/include/asm-arm/arch-lh7a40x/constants.h @@ -29,8 +29,7 @@ #if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404) -# define IOBARRIER_PHYS 0xc0000000 /* Start of SDRAM */ -/*# define IOBARRIER_PHYS 0x00000000 */ /* Start of flash */ +# define IOBARRIER_PHYS 0x10000000 /* Second bank, fastest timing */ # define IOBARRIER_VIRT 0xf0000000 # define IOBARRIER_SIZE PAGE_SIZE @@ -53,6 +52,9 @@ # define CPLD08_PHYS CPLDX_PHYS (0x08) # define CPLD08_VIRT CPLDX_VIRT (0x08) # define CPLD08_SIZE PAGE_SIZE +# define CPLD0A_PHYS CPLDX_PHYS (0x0a) +# define CPLD0A_VIRT CPLDX_VIRT (0x0a) +# define CPLD0A_SIZE PAGE_SIZE # define CPLD0C_PHYS CPLDX_PHYS (0x0c) # define CPLD0C_VIRT CPLDX_VIRT (0x0c) # define CPLD0C_SIZE PAGE_SIZE @@ -84,5 +86,7 @@ #define XTAL_IN 14745600 /* 14.7456 MHz crystal */ #define PLL_CLOCK (XTAL_IN * 21) /* 309 MHz PLL clock */ #define MAX_HCLK_KHZ 100000 /* HCLK max limit ~100MHz */ +#define HCLK (99993600) +//#define HCLK (119808000) #endif /* __ASM_ARCH_CONSTANTS_H */ diff --git a/include/asm-arm/arch-lh7a40x/dma.h b/include/asm-arm/arch-lh7a40x/dma.h index 15492e3253f..a8cbd14bbf9 100644 --- a/include/asm-arm/arch-lh7a40x/dma.h +++ b/include/asm-arm/arch-lh7a40x/dma.h @@ -1,9 +1,86 @@ /* include/asm-arm/arch-lh7a40x/dma.h * - * Copyright (C) 2003 Coastal Environmental Systems + * Copyright (C) 2005 Marc Singer * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * */ + +typedef enum { + DMA_M2M0 = 0, + DMA_M2M1 = 1, + DMA_M2P0 = 2, /* Tx */ + DMA_M2P1 = 3, /* Rx */ + DMA_M2P2 = 4, /* Tx */ + DMA_M2P3 = 5, /* Rx */ + DMA_M2P4 = 6, /* Tx - AC97 */ + DMA_M2P5 = 7, /* Rx - AC97 */ + DMA_M2P6 = 8, /* Tx */ + DMA_M2P7 = 9, /* Rx */ +} dma_device_t; + +#define DMA_LENGTH_MAX ((64*1024) - 4) /* bytes */ + +#define DMAC_GCA __REG(DMAC_PHYS + 0x2b80) +#define DMAC_GIR __REG(DMAC_PHYS + 0x2bc0) + +#define DMAC_GIR_MMI1 (1<<11) +#define DMAC_GIR_MMI0 (1<<10) +#define DMAC_GIR_MPI8 (1<<9) +#define DMAC_GIR_MPI9 (1<<8) +#define DMAC_GIR_MPI6 (1<<7) +#define DMAC_GIR_MPI7 (1<<6) +#define DMAC_GIR_MPI4 (1<<5) +#define DMAC_GIR_MPI5 (1<<4) +#define DMAC_GIR_MPI2 (1<<3) +#define DMAC_GIR_MPI3 (1<<2) +#define DMAC_GIR_MPI0 (1<<1) +#define DMAC_GIR_MPI1 (1<<0) + +#define DMAC_M2P0 0x0000 +#define DMAC_M2P1 0x0040 +#define DMAC_M2P2 0x0080 +#define DMAC_M2P3 0x00c0 +#define DMAC_M2P4 0x0240 +#define DMAC_M2P5 0x0200 +#define DMAC_M2P6 0x02c0 +#define DMAC_M2P7 0x0280 +#define DMAC_M2P8 0x0340 +#define DMAC_M2P9 0x0300 +#define DMAC_M2M0 0x0100 +#define DMAC_M2M1 0x0140 + +#define DMAC_P_PCONTROL(c) __REG(DMAC_PHYS + (c) + 0x00) +#define DMAC_P_PINTERRUPT(c) __REG(DMAC_PHYS + (c) + 0x04) +#define DMAC_P_PPALLOC(c) __REG(DMAC_PHYS + (c) + 0x08) +#define DMAC_P_PSTATUS(c) __REG(DMAC_PHYS + (c) + 0x0c) +#define DMAC_P_REMAIN(c) __REG(DMAC_PHYS + (c) + 0x14) +#define DMAC_P_MAXCNT0(c) __REG(DMAC_PHYS + (c) + 0x20) +#define DMAC_P_BASE0(c) __REG(DMAC_PHYS + (c) + 0x24) +#define DMAC_P_CURRENT0(c) __REG(DMAC_PHYS + (c) + 0x28) +#define DMAC_P_MAXCNT1(c) __REG(DMAC_PHYS + (c) + 0x30) +#define DMAC_P_BASE1(c) __REG(DMAC_PHYS + (c) + 0x34) +#define DMAC_P_CURRENT1(c) __REG(DMAC_PHYS + (c) + 0x38) + +#define DMAC_PCONTROL_ENABLE (1<<4) + +#define DMAC_PORT_USB 0 +#define DMAC_PORT_SDMMC 1 +#define DMAC_PORT_AC97_1 2 +#define DMAC_PORT_AC97_2 3 +#define DMAC_PORT_AC97_3 4 +#define DMAC_PORT_UART1 6 +#define DMAC_PORT_UART2 7 +#define DMAC_PORT_UART3 8 + +#define DMAC_PSTATUS_CURRSTATE_SHIFT 4 +#define DMAC_PSTATUS_CURRSTATE_MASK 0x3 + +#define DMAC_PSTATUS_NEXTBUF (1<<6) +#define DMAC_PSTATUS_STALLRINT (1<<0) + +#define DMAC_INT_CHE (1<<3) +#define DMAC_INT_NFB (1<<1) +#define DMAC_INT_STALL (1<<0) diff --git a/include/asm-arm/arch-lh7a40x/entry-macro.S b/include/asm-arm/arch-lh7a40x/entry-macro.S index a2f67c06d9c..9fc7f498812 100644 --- a/include/asm-arm/arch-lh7a40x/entry-macro.S +++ b/include/asm-arm/arch-lh7a40x/entry-macro.S @@ -10,11 +10,73 @@ #include <asm/hardware.h> #include <asm/arch/irqs.h> -# if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404) -# error "LH7A400 and LH7A404 are mutually exclusive" -# endif +/* In order to allow there to be support for both of the processor + classes at the same time, we make a hack here that isn't very + pretty. At startup, the link pointed to with the + branch_irq_lh7a400 symbol is replaced with a NOP when the CPU is + detected as a lh7a404. -# if defined (CONFIG_ARCH_LH7A400) + *** FIXME: we should clean this up so that there is only one + implementation for each CPU's design. + +*/ + +#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404) + + .macro disable_fiq + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + +branch_irq_lh7a400: b 1000f + +@ Implementation of the LH7A404 get_irqnr_and_base. + + mov \irqnr, #0 @ VIC1 irq base + mov \base, #io_p2v(0x80000000) @ APB registers + add \base, \base, #0x8000 + ldr \tmp, [\base, #0x0030] @ VIC1_VECTADDR + tst \tmp, #VA_VECTORED @ Direct vectored + bne 1002f + tst \tmp, #VA_VIC1DEFAULT @ Default vectored VIC1 + ldrne \irqstat, [\base, #0] @ VIC1_IRQSTATUS + bne 1001f + add \base, \base, #(0xa000 - 0x8000) + ldr \tmp, [\base, #0x0030] @ VIC2_VECTADDR + tst \tmp, #VA_VECTORED @ Direct vectored + bne 1002f + ldr \irqstat, [\base, #0] @ VIC2_IRQSTATUS + mov \irqnr, #32 @ VIC2 irq base + +1001: movs \irqstat, \irqstat, lsr #1 @ Shift into carry + bcs 1008f @ Bit set; irq found + add \irqnr, \irqnr, #1 + bne 1001b @ Until no bits + b 1009f @ Nothing? Hmm. +1002: and \irqnr, \tmp, #0x3f @ Mask for valid bits +1008: movs \irqstat, #1 @ Force !Z + str \tmp, [\base, #0x0030] @ Clear vector + b 1009f + +@ Implementation of the LH7A400 get_irqnr_and_base. + +1000: mov \irqnr, #0 + mov \base, #io_p2v(0x80000000) @ APB registers + ldr \irqstat, [\base, #0x500] @ PIC INTSR + +1001: movs \irqstat, \irqstat, lsr #1 @ Shift into carry + bcs 1008f @ Bit set; irq found + add \irqnr, \irqnr, #1 + bne 1001b @ Until no bits + b 1009f @ Nothing? Hmm. +1008: movs \irqstat, #1 @ Force !Z + +1009: + .endm + + + +#elif defined (CONFIG_ARCH_LH7A400) .macro disable_fiq .endm diff --git a/include/asm-arm/arch-lh7a40x/hardware.h b/include/asm-arm/arch-lh7a40x/hardware.h index aeb07c162e2..e9ff74fd793 100644 --- a/include/asm-arm/arch-lh7a40x/hardware.h +++ b/include/asm-arm/arch-lh7a40x/hardware.h @@ -13,6 +13,8 @@ #ifndef __ASM_ARCH_HARDWARE_H #define __ASM_ARCH_HARDWARE_H +#include <asm/sizes.h> /* Added for the sake of amba-clcd driver */ + #define io_p2v(x) (0xf0000000 | (((x) & 0xfff00000) >> 4) | ((x) & 0x0000ffff)) #define io_v2p(x) ( (((x) & 0x0fff0000) << 4) | ((x) & 0x0000ffff)) @@ -53,6 +55,8 @@ typedef struct { volatile u8 offset[4096]; } __regbase8; #endif +#define MASK_AND_SET(v,m,s) (v) = ((v)&~(m))|(s) + #include "registers.h" #endif /* _ASM_ARCH_HARDWARE_H */ diff --git a/include/asm-arm/arch-lh7a40x/irqs.h b/include/asm-arm/arch-lh7a40x/irqs.h index f91f3e59f3a..7e8a217200e 100644 --- a/include/asm-arm/arch-lh7a40x/irqs.h +++ b/include/asm-arm/arch-lh7a40x/irqs.h @@ -154,9 +154,10 @@ #if !defined (IRQ_GPIO0INTR) # define IRQ_GPIO0INTR IRQ_GPIO0FIQ #endif -#define IRQ_TICK IRQ_TINTR +#define IRQ_TICK IRQ_TINTR #define IRQ_PCC1_RDY IRQ_GPIO6INTR /* PCCard 1 ready */ #define IRQ_PCC2_RDY IRQ_GPIO7INTR /* PCCard 2 ready */ +#define IRQ_USB IRQ_USBINTR /* USB device */ #ifdef CONFIG_MACH_KEV7A400 # define IRQ_TS IRQ_GPIOFIQ /* Touchscreen */ @@ -191,6 +192,10 @@ # define IRQ_LPD7A400_TS IRQ_LPD7A40X_CPLD + 1 /* Touch screen */ #endif +#if defined (CONFIG_MACH_LPD7A400) +# define IRQ_TOUCH IRQ_LPD7A400_TS +#endif + #define NR_IRQS (NR_IRQ_CPU + NR_IRQ_BOARD) #endif diff --git a/include/asm-arm/arch-lh7a40x/registers.h b/include/asm-arm/arch-lh7a40x/registers.h index 2edb22e3545..544307bb87a 100644 --- a/include/asm-arm/arch-lh7a40x/registers.h +++ b/include/asm-arm/arch-lh7a40x/registers.h @@ -18,7 +18,7 @@ /* Physical register base addresses */ -#define AC97_PHYS (0x80000000) /* AC97 Controller */ +#define AC97C_PHYS (0x80000000) /* AC97 Controller */ #define MMC_PHYS (0x80000100) /* Multimedia Card Controller */ #define USB_PHYS (0x80000200) /* USB Client */ #define SCI_PHYS (0x80000300) /* Secure Card Interface */ @@ -35,6 +35,8 @@ #define RTC_PHYS (0x80000d00) /* Real-time Clock */ #define GPIO_PHYS (0x80000e00) /* General Purpose IO */ #define BMI_PHYS (0x80000f00) /* Battery Monitor Interface */ +#define HRTFTC_PHYS (0x80001000) /* High-res TFT Controller (LH7A400) */ +#define ALI_PHYS (0x80001000) /* Advanced LCD Interface (LH7A404) */ #define WDT_PHYS (0x80001400) /* Watchdog Timer */ #define SMC_PHYS (0x80002000) /* Static Memory Controller */ #define SDRC_PHYS (0x80002400) /* SDRAM Controller */ @@ -43,6 +45,7 @@ /* Physical registers of the LH7A404 */ +#define ADC_PHYS (0x80001300) /* A/D & Touchscreen Controller */ #define VIC1_PHYS (0x80008000) /* Vectored Interrupt Controller 1 */ #define USBH_PHYS (0x80009000) /* USB OHCI host controller */ #define VIC2_PHYS (0x8000a000) /* Vectored Interrupt Controller 2 */ @@ -53,10 +56,32 @@ /* Clock/State Controller register */ +#define CSC_PWRSR __REG(CSC_PHYS + 0x00) /* Reset register & ID */ #define CSC_PWRCNT __REG(CSC_PHYS + 0x04) /* Power control */ +#define CSC_CLKSET __REG(CSC_PHYS + 0x20) /* Clock speed control */ +#define CSC_USBDRESET __REG(CSC_PHYS + 0x4c) /* USB Device resets */ #define CSC_PWRCNT_USBH_EN (1<<28) /* USB Host power enable */ - +#define CSC_PWRCNT_DMAC_M2M1_EN (1<<27) +#define CSC_PWRCNT_DMAC_M2M0_EN (1<<26) +#define CSC_PWRCNT_DMAC_M2P8_EN (1<<25) +#define CSC_PWRCNT_DMAC_M2P9_EN (1<<24) +#define CSC_PWRCNT_DMAC_M2P6_EN (1<<23) +#define CSC_PWRCNT_DMAC_M2P7_EN (1<<22) +#define CSC_PWRCNT_DMAC_M2P4_EN (1<<21) +#define CSC_PWRCNT_DMAC_M2P5_EN (1<<20) +#define CSC_PWRCNT_DMAC_M2P2_EN (1<<19) +#define CSC_PWRCNT_DMAC_M2P3_EN (1<<18) +#define CSC_PWRCNT_DMAC_M2P0_EN (1<<17) +#define CSC_PWRCNT_DMAC_M2P1_EN (1<<16) + +#define CSC_PWRSR_CHIPMAN_SHIFT (24) +#define CSC_PWRSR_CHIPMAN_MASK (0xff) +#define CSC_PWRSR_CHIPID_SHIFT (16) +#define CSC_PWRSR_CHIPID_MASK (0xff) + +#define CSC_USBDRESET_APBRESETREG (1<<1) +#define CSC_USBDRESET_IORESETREG (1<<0) /* Interrupt Controller registers */ @@ -109,6 +134,13 @@ #define GPIO_GPIOFEOI __REG(GPIO_PHYS + 0x54) /* GPIO End-of-Interrupt */ #define GPIO_GPIOINTEN __REG(GPIO_PHYS + 0x58) /* GPIO Interrupt Enable */ #define GPIO_INTSTATUS __REG(GPIO_PHYS + 0x5c) /* GPIO Interrupt Status */ +#define GPIO_PINMUX __REG(GPIO_PHYS + 0x2c) +#define GPIO_PADD __REG(GPIO_PHYS + 0x10) +#define GPIO_PAD __REG(GPIO_PHYS + 0x00) +#define GPIO_PCD __REG(GPIO_PHYS + 0x08) +#define GPIO_PCDD __REG(GPIO_PHYS + 0x18) +#define GPIO_PEDD __REG(GPIO_PHYS + 0x24) +#define GPIO_PED __REG(GPIO_PHYS + 0x20) /* Static Memory Controller registers */ @@ -138,20 +170,21 @@ #endif #if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404) -# define CPLD_CONTROL __REG8(CPLD02_PHYS) -# define CPLD_SPI_DATA __REG8(CPLD06_PHYS) -# define CPLD_SPI_CONTROL __REG8(CPLD08_PHYS) -# define CPLD_SPI_EEPROM __REG8(CPLD0A_PHYS) -# define CPLD_INTERRUPTS __REG8(CPLD0C_PHYS) /* IRQ mask/status */ -# define CPLD_BOOT_MODE __REG8(CPLD0E_PHYS) -# define CPLD_FLASH __REG8(CPLD10_PHYS) -# define CPLD_POWER_MGMT __REG8(CPLD12_PHYS) -# define CPLD_REVISION __REG8(CPLD14_PHYS) -# define CPLD_GPIO_EXT __REG8(CPLD16_PHYS) -# define CPLD_GPIO_DATA __REG8(CPLD18_PHYS) -# define CPLD_GPIO_DIR __REG8(CPLD1A_PHYS) -#endif +# define CPLD_CONTROL __REG16(CPLD02_PHYS) +# define CPLD_SPI_DATA __REG16(CPLD06_PHYS) +# define CPLD_SPI_CONTROL __REG16(CPLD08_PHYS) +# define CPLD_SPI_EEPROM __REG16(CPLD0A_PHYS) +# define CPLD_INTERRUPTS __REG16(CPLD0C_PHYS) /* IRQ mask/status */ +# define CPLD_BOOT_MODE __REG16(CPLD0E_PHYS) +# define CPLD_FLASH __REG16(CPLD10_PHYS) +# define CPLD_POWER_MGMT __REG16(CPLD12_PHYS) +# define CPLD_REVISION __REG16(CPLD14_PHYS) +# define CPLD_GPIO_EXT __REG16(CPLD16_PHYS) +# define CPLD_GPIO_DATA __REG16(CPLD18_PHYS) +# define CPLD_GPIO_DIR __REG16(CPLD1A_PHYS) + +#endif /* Timer registers */ @@ -190,4 +223,3 @@ #endif /* _ASM_ARCH_REGISTERS_H */ - diff --git a/include/asm-arm/arch-lh7a40x/ssp.h b/include/asm-arm/arch-lh7a40x/ssp.h new file mode 100644 index 00000000000..132b1c4d5ce --- /dev/null +++ b/include/asm-arm/arch-lh7a40x/ssp.h @@ -0,0 +1,71 @@ +/* ssp.h + $Id$ + + written by Marc Singer + 6 Dec 2004 + + Copyright (C) 2004 Marc Singer + + ----------- + DESCRIPTION + ----------- + + This SSP header is available throughout the kernel, for this + machine/architecture, because drivers that use it may be dispersed. + + This file was cloned from the 7952x implementation. It would be + better to share them, but we're taking an easier approach for the + time being. + +*/ + +#if !defined (__SSP_H__) +# define __SSP_H__ + +/* ----- Includes */ + +/* ----- Types */ + +struct ssp_driver { + int (*init) (void); + void (*exit) (void); + void (*acquire) (void); + void (*release) (void); + int (*configure) (int device, int mode, int speed, + int frame_size_write, int frame_size_read); + void (*chip_select) (int enable); + void (*set_callbacks) (void* handle, + irqreturn_t (*callback_tx)(void*), + irqreturn_t (*callback_rx)(void*)); + void (*enable) (void); + void (*disable) (void); +// int (*save_state) (void*); +// void (*restore_state) (void*); + int (*read) (void); + int (*write) (u16 data); + int (*write_read) (u16 data); + void (*flush) (void); + void (*write_async) (void* pv, size_t cb); + size_t (*write_pos) (void); +}; + + /* These modes are only available on the LH79524 */ +#define SSP_MODE_SPI (1) +#define SSP_MODE_SSI (2) +#define SSP_MODE_MICROWIRE (3) +#define SSP_MODE_I2S (4) + + /* CPLD SPI devices */ +#define DEVICE_EEPROM 0 /* Configuration eeprom */ +#define DEVICE_MAC 1 /* MAC eeprom (LPD79524) */ +#define DEVICE_CODEC 2 /* Audio codec */ +#define DEVICE_TOUCH 3 /* Touch screen (LPD79520) */ + +/* ----- Globals */ + +/* ----- Prototypes */ + +//extern struct ssp_driver lh79520_i2s_driver; +extern struct ssp_driver lh7a400_cpld_ssp_driver; + +#endif /* __SSP_H__ */ diff --git a/include/asm-arm/arch-lh7a40x/uncompress.h b/include/asm-arm/arch-lh7a40x/uncompress.h index f8053346f60..3d1ce0426a3 100644 --- a/include/asm-arm/arch-lh7a40x/uncompress.h +++ b/include/asm-arm/arch-lh7a40x/uncompress.h @@ -16,7 +16,7 @@ #ifndef UART_R_STATUS # define UART_R_STATUS (0x10) #endif -#define nTxRdy (0x20) /* Not TxReady (literally Tx FIFO full) */ +#define nTxRdy (0x20) /* Not TxReady (literally Tx FIFO full) */ /* Access UART with physical addresses before MMU is setup */ #define UART_STATUS (*(volatile unsigned long*) (UART2_PHYS + UART_R_STATUS)) diff --git a/include/asm-arm/arch-pnx4008/clock.h b/include/asm-arm/arch-pnx4008/clock.h new file mode 100644 index 00000000000..91ae0030fdf --- /dev/null +++ b/include/asm-arm/arch-pnx4008/clock.h @@ -0,0 +1,61 @@ +/* + * include/asm-arm/arch-pnx4008/clock.h + * + * Clock control driver for PNX4008 - header file + * + * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com> + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#ifndef __PNX4008_CLOCK_H__ +#define __PNX4008_CLOCK_H__ + +struct module; +struct clk; + +#define PWRMAN_VA_BASE IO_ADDRESS(PNX4008_PWRMAN_BASE) +#define HCLKDIVCTRL_REG (PWRMAN_VA_BASE + 0x40) +#define PWRCTRL_REG (PWRMAN_VA_BASE + 0x44) +#define PLLCTRL_REG (PWRMAN_VA_BASE + 0x48) +#define OSC13CTRL_REG (PWRMAN_VA_BASE + 0x4c) +#define SYSCLKCTRL_REG (PWRMAN_VA_BASE + 0x50) +#define HCLKPLLCTRL_REG (PWRMAN_VA_BASE + 0x58) +#define USBCTRL_REG (PWRMAN_VA_BASE + 0x64) +#define SDRAMCLKCTRL_REG (PWRMAN_VA_BASE + 0x68) +#define MSCTRL_REG (PWRMAN_VA_BASE + 0x80) +#define BTCLKCTRL (PWRMAN_VA_BASE + 0x84) +#define DUMCLKCTRL_REG (PWRMAN_VA_BASE + 0x90) +#define I2CCLKCTRL_REG (PWRMAN_VA_BASE + 0xac) +#define KEYCLKCTRL_REG (PWRMAN_VA_BASE + 0xb0) +#define TSCLKCTRL_REG (PWRMAN_VA_BASE + 0xb4) +#define PWMCLKCTRL_REG (PWRMAN_VA_BASE + 0xb8) +#define SPICTRL_REG (PWRMAN_VA_BASE + 0xc4) +#define FLASHCLKCTRL_REG (PWRMAN_VA_BASE + 0xc8) +#define UART3CLK_REG (PWRMAN_VA_BASE + 0xd0) +#define UARTCLKCTRL_REG (PWRMAN_VA_BASE + 0xe4) +#define DMACLKCTRL_REG (PWRMAN_VA_BASE + 0xe8) +#define AUTOCLK_CTRL (PWRMAN_VA_BASE + 0xec) +#define JPEGCLKCTRL_REG (PWRMAN_VA_BASE + 0xfc) + +#define AUDIOCONFIG_VA_BASE IO_ADDRESS(PNX4008_AUDIOCONFIG_BASE) +#define DSPPLLCTRL_REG (AUDIOCONFIG_VA_BASE + 0x60) +#define DSPCLKCTRL_REG (AUDIOCONFIG_VA_BASE + 0x64) +#define AUDIOCLKCTRL_REG (AUDIOCONFIG_VA_BASE + 0x68) +#define AUDIOPLLCTRL_REG (AUDIOCONFIG_VA_BASE + 0x6C) + +#define USB_OTG_CLKCTRL_REG IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0xff4) + +#define VFP9CLKCTRL_REG IO_ADDRESS(PNX4008_DEBUG_BASE) + +#define CLK_RATE_13MHZ 13000 +#define CLK_RATE_1MHZ 1000 +#define CLK_RATE_208MHZ 208000 +#define CLK_RATE_48MHZ 48000 +#define CLK_RATE_32KHZ 32 + +#define PNX4008_UART_CLK CLK_RATE_13MHZ * 1000 /* in MHz */ + +#endif diff --git a/include/asm-arm/arch-pnx4008/debug-macro.S b/include/asm-arm/arch-pnx4008/debug-macro.S new file mode 100644 index 00000000000..eb3839de389 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/debug-macro.S @@ -0,0 +1,27 @@ +/* linux/include/asm-arm/arch-pnx4008/debug-macro.S + * + * Debugging macro include header + * + * Copyright (C) 1994-1999 Russell King + * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + mov \rx, #0x00090000 + addeq \rx, \rx, #0x40000000 + addne \rx, \rx, #0xf4000000 + .endm + + .macro senduart,rd,rx + strb \rd, [\rx, #0x0] + .endm + +#define UART_SHIFT 2 +#include <asm/hardware/debug-8250.S> diff --git a/include/asm-arm/arch-pnx4008/dma.h b/include/asm-arm/arch-pnx4008/dma.h new file mode 100644 index 00000000000..3aee1204795 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/dma.h @@ -0,0 +1,162 @@ +/* + * linux/include/asm-arm/arch-pnx4008/dma.h + * + * PNX4008 DMA header file + * + * Author: Vitaly Wool + * Copyright: MontaVista Software Inc. (c) 2005 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_DMA_H +#define __ASM_ARCH_DMA_H + +#include "platform.h" + +#define MAX_DMA_ADDRESS 0xffffffff + +#define MAX_DMA_CHANNELS 8 + +#define DMAC_BASE IO_ADDRESS(PNX4008_DMA_CONFIG_BASE) +#define DMAC_INT_STAT (DMAC_BASE + 0x0000) +#define DMAC_INT_TC_STAT (DMAC_BASE + 0x0004) +#define DMAC_INT_TC_CLEAR (DMAC_BASE + 0x0008) +#define DMAC_INT_ERR_STAT (DMAC_BASE + 0x000c) +#define DMAC_INT_ERR_CLEAR (DMAC_BASE + 0x0010) +#define DMAC_SOFT_SREQ (DMAC_BASE + 0x0024) +#define DMAC_CONFIG (DMAC_BASE + 0x0030) +#define DMAC_Cx_SRC_ADDR(c) (DMAC_BASE + 0x0100 + (c) * 0x20) +#define DMAC_Cx_DEST_ADDR(c) (DMAC_BASE + 0x0104 + (c) * 0x20) +#define DMAC_Cx_LLI(c) (DMAC_BASE + 0x0108 + (c) * 0x20) +#define DMAC_Cx_CONTROL(c) (DMAC_BASE + 0x010c + (c) * 0x20) +#define DMAC_Cx_CONFIG(c) (DMAC_BASE + 0x0110 + (c) * 0x20) + +enum { + WIDTH_BYTE = 0, + WIDTH_HWORD, + WIDTH_WORD +}; + +enum { + FC_MEM2MEM_DMA, + FC_MEM2PER_DMA, + FC_PER2MEM_DMA, + FC_PER2PER_DMA, + FC_PER2PER_DPER, + FC_MEM2PER_PER, + FC_PER2MEM_PER, + FC_PER2PER_SPER +}; + +enum { + DMA_INT_UNKNOWN = 0, + DMA_ERR_INT = 1, + DMA_TC_INT = 2, +}; + +enum { + DMA_BUFFER_ALLOCATED = 1, + DMA_HAS_LL = 2, +}; + +enum { + PER_CAM_DMA_1 = 0, + PER_NDF_FLASH = 1, + PER_MBX_SLAVE_FIFO = 2, + PER_SPI2_REC_XMIT = 3, + PER_MS_SD_RX_XMIT = 4, + PER_HS_UART_1_XMIT = 5, + PER_HS_UART_1_RX = 6, + PER_HS_UART_2_XMIT = 7, + PER_HS_UART_2_RX = 8, + PER_HS_UART_7_XMIT = 9, + PER_HS_UART_7_RX = 10, + PER_SPI1_REC_XMIT = 11, + PER_MLC_NDF_SREC = 12, + PER_CAM_DMA_2 = 13, + PER_PRNG_INFIFO = 14, + PER_PRNG_OUTFIFO = 15, +}; + +struct pnx4008_dma_ch_ctrl { + int tc_mask; + int cacheable; + int bufferable; + int priv_mode; + int di; + int si; + int dest_ahb1; + int src_ahb1; + int dwidth; + int swidth; + int dbsize; + int sbsize; + int tr_size; +}; + +struct pnx4008_dma_ch_config { + int halt; + int active; + int lock; + int itc; + int ie; + int flow_cntrl; + int dest_per; + int src_per; +}; + +struct pnx4008_dma_ll { + unsigned long src_addr; + unsigned long dest_addr; + u32 next_dma; + unsigned long ch_ctrl; + struct pnx4008_dma_ll *next; + int flags; + void *alloc_data; + int (*free) (void *); +}; + +struct pnx4008_dma_config { + int is_ll; + unsigned long src_addr; + unsigned long dest_addr; + unsigned long ch_ctrl; + unsigned long ch_cfg; + struct pnx4008_dma_ll *ll; + u32 ll_dma; + int flags; + void *alloc_data; + int (*free) (void *); +}; + +extern struct pnx4008_dma_ll *pnx4008_alloc_ll_entry(dma_addr_t *); +extern void pnx4008_free_ll_entry(struct pnx4008_dma_ll *, dma_addr_t); +extern void pnx4008_free_ll(u32 ll_dma, struct pnx4008_dma_ll *); + +extern int pnx4008_request_channel(char *, int, + void (*)(int, int, void *, struct pt_regs *), + void *); +extern void pnx4008_free_channel(int); +extern int pnx4008_config_dma(int, int, int); +extern int pnx4008_dma_pack_control(const struct pnx4008_dma_ch_ctrl *, + unsigned long *); +extern int pnx4008_dma_parse_control(unsigned long, + struct pnx4008_dma_ch_ctrl *); +extern int pnx4008_dma_pack_config(const struct pnx4008_dma_ch_config *, + unsigned long *); +extern int pnx4008_dma_parse_config(unsigned long, + struct pnx4008_dma_ch_config *); +extern int pnx4008_config_channel(int, struct pnx4008_dma_config *); +extern int pnx4008_channel_get_config(int, struct pnx4008_dma_config *); +extern int pnx4008_dma_ch_enable(int); +extern int pnx4008_dma_ch_disable(int); +extern int pnx4008_dma_ch_enabled(int); +extern void pnx4008_dma_split_head_entry(struct pnx4008_dma_config *, + struct pnx4008_dma_ch_ctrl *); +extern void pnx4008_dma_split_ll_entry(struct pnx4008_dma_ll *, + struct pnx4008_dma_ch_ctrl *); + +#endif /* _ASM_ARCH_DMA_H */ diff --git a/include/asm-arm/arch-pnx4008/entry-macro.S b/include/asm-arm/arch-pnx4008/entry-macro.S new file mode 100644 index 00000000000..c1c198e3680 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/entry-macro.S @@ -0,0 +1,121 @@ +/* + * include/asm-arm/arch-pnx4008/entry-macro.S + * + * Low-level IRQ helper macros for PNX4008-based platforms + * + * 2005-2006 (c) MontaVista Software, Inc. + * Author: Vitaly Wool <vwool@ru.mvista.com> + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include "platform.h" + +#define IO_BASE 0xF0000000 +#define IO_ADDRESS(x) (((((x) & 0xff000000) >> 4) | ((x) & 0xfffff)) | IO_BASE) + +#define INTRC_MASK 0x00 +#define INTRC_RAW_STAT 0x04 +#define INTRC_STAT 0x08 +#define INTRC_POLAR 0x0C +#define INTRC_ACT_TYPE 0x10 +#define INTRC_TYPE 0x14 + +#define SIC1_BASE_INT 32 +#define SIC2_BASE_INT 64 + + .macro disable_fiq + .endm + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp +/* decode the MIC interrupt numbers */ + ldr \base, =IO_ADDRESS(PNX4008_INTCTRLMIC_BASE) + ldr \irqstat, [\base, #INTRC_STAT] + + cmp \irqstat,#1<<16 + movhs \irqnr,#16 + movlo \irqnr,#0 + movhs \irqstat,\irqstat,lsr#16 + cmp \irqstat,#1<<8 + addhs \irqnr,\irqnr,#8 + movhs \irqstat,\irqstat,lsr#8 + cmp \irqstat,#1<<4 + addhs \irqnr,\irqnr,#4 + movhs \irqstat,\irqstat,lsr#4 + cmp \irqstat,#1<<2 + addhs \irqnr,\irqnr,#2 + movhs \irqstat,\irqstat,lsr#2 + cmp \irqstat,#1<<1 + addhs \irqnr,\irqnr,#1 + +/* was there an interrupt ? if not then drop out with EQ status */ + teq \irqstat,#0 + beq 1003f + +/* and now check for extended IRQ reasons */ + cmp \irqnr,#1 + bls 1003f + cmp \irqnr,#30 + blo 1002f + +/* IRQ 31,30 : High priority cascade IRQ handle */ +/* read the correct SIC */ +/* decoding status after compare : eq is 30 (SIC1) , ne is 31 (SIC2) */ +/* set the base IRQ number */ + ldreq \base, =IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE) + moveq \irqnr,#SIC1_BASE_INT + ldrne \base, =IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE) + movne \irqnr,#SIC2_BASE_INT + ldr \irqstat, [\base, #INTRC_STAT] + ldr \tmp, [\base, #INTRC_TYPE] +/* and with inverted mask : low priority interrupts */ + and \irqstat,\irqstat,\tmp + b 1004f + +1003: +/* IRQ 1,0 : Low priority cascade IRQ handle */ +/* read the correct SIC */ +/* decoding status after compare : eq is 1 (SIC2) , ne is 0 (SIC1)*/ +/* read the correct SIC */ +/* set the base IRQ number */ + ldrne \base, =IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE) + movne \irqnr,#SIC1_BASE_INT + ldreq \base, =IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE) + moveq \irqnr,#SIC2_BASE_INT + ldr \irqstat, [\base, #INTRC_STAT] + ldr \tmp, [\base, #INTRC_TYPE] +/* and with inverted mask : low priority interrupts */ + bic \irqstat,\irqstat,\tmp + +1004: + + cmp \irqstat,#1<<16 + addhs \irqnr,\irqnr,#16 + movhs \irqstat,\irqstat,lsr#16 + cmp \irqstat,#1<<8 + addhs \irqnr,\irqnr,#8 + movhs \irqstat,\irqstat,lsr#8 + cmp \irqstat,#1<<4 + addhs \irqnr,\irqnr,#4 + movhs \irqstat,\irqstat,lsr#4 + cmp \irqstat,#1<<2 + addhs \irqnr,\irqnr,#2 + movhs \irqstat,\irqstat,lsr#2 + cmp \irqstat,#1<<1 + addhs \irqnr,\irqnr,#1 + + +/* is irqstat not zero */ + +1002: +/* we assert that irqstat is not equal to zero and return ne status if true*/ + teq \irqstat,#0 +1003: + .endm + + + .macro irq_prio_table + .endm + + diff --git a/include/asm-arm/arch-pnx4008/gpio.h b/include/asm-arm/arch-pnx4008/gpio.h new file mode 100644 index 00000000000..1fa5a77c301 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/gpio.h @@ -0,0 +1,139 @@ +/* + * include/asm-arm/arch-pnx4008/gpio.h + * + * PNX4008 GPIO driver - header file + * + * Author: Dmitry Chigirev <source@mvista.com> + * + * Based on reference code by Iwo Mergler and Z.Tabaaloute from Philips: + * Copyright (c) 2005 Koninklijke Philips Electronics N.V. + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#ifndef _PNX4008_GPIO_H_ +#define _PNX4008_GPIO_H_ + + +/* Block numbers */ +#define GPIO_IN (0) +#define GPIO_OUT (0x100) +#define GPIO_BID (0x200) +#define GPIO_RAM (0x300) +#define GPIO_MUX (0x400) + +#define GPIO_TYPE_MASK(K) ((K) & 0x700) + +/* INPUT GPIOs */ +/* GPI */ +#define GPI_00 (GPIO_IN | 0) +#define GPI_01 (GPIO_IN | 1) +#define GPI_02 (GPIO_IN | 2) +#define GPI_03 (GPIO_IN | 3) +#define GPI_04 (GPIO_IN | 4) +#define GPI_05 (GPIO_IN | 5) +#define GPI_06 (GPIO_IN | 6) +#define GPI_07 (GPIO_IN | 7) +#define GPI_08 (GPIO_IN | 8) +#define GPI_09 (GPIO_IN | 9) +#define U1_RX (GPIO_IN | 15) +#define U2_HTCS (GPIO_IN | 16) +#define U2_RX (GPIO_IN | 17) +#define U3_RX (GPIO_IN | 18) +#define U4_RX (GPIO_IN | 19) +#define U5_RX (GPIO_IN | 20) +#define U6_IRRX (GPIO_IN | 21) +#define U7_HCTS (GPIO_IN | 22) +#define U7_RX (GPIO_IN | 23) +/* MISC IN */ +#define SPI1_DATIN (GPIO_IN | 25) +#define DISP_SYNC (GPIO_IN | 26) +#define SPI2_DATIN (GPIO_IN | 27) +#define GPI_11 (GPIO_IN | 28) + +#define GPIO_IN_MASK 0x1eff83ff + +/* OUTPUT GPIOs */ +/* GPO */ +#define GPO_00 (GPIO_OUT | 0) +#define GPO_01 (GPIO_OUT | 1) +#define GPO_02 (GPIO_OUT | 2) +#define GPO_03 (GPIO_OUT | 3) +#define GPO_04 (GPIO_OUT | 4) +#define GPO_05 (GPIO_OUT | 5) +#define GPO_06 (GPIO_OUT | 6) +#define GPO_07 (GPIO_OUT | 7) +#define GPO_08 (GPIO_OUT | 8) +#define GPO_09 (GPIO_OUT | 9) +#define GPO_10 (GPIO_OUT | 10) +#define GPO_11 (GPIO_OUT | 11) +#define GPO_12 (GPIO_OUT | 12) +#define GPO_13 (GPIO_OUT | 13) +#define GPO_14 (GPIO_OUT | 14) +#define GPO_15 (GPIO_OUT | 15) +#define GPO_16 (GPIO_OUT | 16) +#define GPO_17 (GPIO_OUT | 17) +#define GPO_18 (GPIO_OUT | 18) +#define GPO_19 (GPIO_OUT | 19) +#define GPO_20 (GPIO_OUT | 20) +#define GPO_21 (GPIO_OUT | 21) +#define GPO_22 (GPIO_OUT | 22) +#define GPO_23 (GPIO_OUT | 23) + +#define GPIO_OUT_MASK 0xffffff + +/* BIDIRECTIONAL GPIOs */ +/* RAM pins */ +#define RAM_D19 (GPIO_RAM | 0) +#define RAM_D20 (GPIO_RAM | 1) +#define RAM_D21 (GPIO_RAM | 2) +#define RAM_D22 (GPIO_RAM | 3) +#define RAM_D23 (GPIO_RAM | 4) +#define RAM_D24 (GPIO_RAM | 5) +#define RAM_D25 (GPIO_RAM | 6) +#define RAM_D26 (GPIO_RAM | 7) +#define RAM_D27 (GPIO_RAM | 8) +#define RAM_D28 (GPIO_RAM | 9) +#define RAM_D29 (GPIO_RAM | 10) +#define RAM_D30 (GPIO_RAM | 11) +#define RAM_D31 (GPIO_RAM | 12) + +#define GPIO_RAM_MASK 0x1fff + +/* I/O pins */ +#define GPIO_00 (GPIO_BID | 25) +#define GPIO_01 (GPIO_BID | 26) +#define GPIO_02 (GPIO_BID | 27) +#define GPIO_03 (GPIO_BID | 28) +#define GPIO_04 (GPIO_BID | 29) +#define GPIO_05 (GPIO_BID | 30) + +#define GPIO_BID_MASK 0x7e000000 + +/* Non-GPIO multiplexed PIOs. For multiplexing with GPIO, please use GPIO macros */ +#define GPIO_SDRAM_SEL (GPIO_MUX | 3) + +#define GPIO_MUX_MASK 0x8 + +/* Extraction/assembly macros */ +#define GPIO_BIT_MASK(K) ((K) & 0x1F) +#define GPIO_BIT(K) (1 << GPIO_BIT_MASK(K)) +#define GPIO_ISMUX(K) ((GPIO_TYPE_MASK(K) == GPIO_MUX) && (GPIO_BIT(K) & GPIO_MUX_MASK)) +#define GPIO_ISRAM(K) ((GPIO_TYPE_MASK(K) == GPIO_RAM) && (GPIO_BIT(K) & GPIO_RAM_MASK)) +#define GPIO_ISBID(K) ((GPIO_TYPE_MASK(K) == GPIO_BID) && (GPIO_BIT(K) & GPIO_BID_MASK)) +#define GPIO_ISOUT(K) ((GPIO_TYPE_MASK(K) == GPIO_OUT) && (GPIO_BIT(K) & GPIO_OUT_MASK)) +#define GPIO_ISIN(K) ((GPIO_TYPE_MASK(K) == GPIO_IN) && (GPIO_BIT(K) & GPIO_IN_MASK)) + +extern int pnx4008_gpio_register_pin(unsigned short pin); +extern int pnx4008_gpio_unregister_pin(unsigned short pin); +extern unsigned long pnx4008_gpio_read_pin(unsigned short pin); +extern int pnx4008_gpio_write_pin(unsigned short pin, int output); +extern int pnx4008_gpio_set_pin_direction(unsigned short pin, int output); +extern int pnx4008_gpio_read_pin_direction(unsigned short pin); +extern int pnx4008_gpio_set_pin_mux(unsigned short pin, int output); +extern int pnx4008_gpio_read_pin_mux(unsigned short pin); + +#endif /* _PNX4008_GPIO_H_ */ diff --git a/include/asm-arm/arch-pnx4008/hardware.h b/include/asm-arm/arch-pnx4008/hardware.h new file mode 100644 index 00000000000..a4410397a92 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/hardware.h @@ -0,0 +1,32 @@ +/* + * linux/include/asm-arm/arch-pnx4008/hardware.h + * + * Copyright (c) 2005 MontaVista Software, Inc. <source@mvista.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include <asm/sizes.h> +#include <asm/arch/platform.h> + +/* Start of virtual addresses for IO devices */ +#define IO_BASE 0xF0000000 + +/* This macro relies on fact that for all HW i/o addresses bits 20-23 are 0 */ +#define IO_ADDRESS(x) (((((x) & 0xff000000) >> 4) | ((x) & 0xfffff)) | IO_BASE) + +#endif diff --git a/include/asm-arm/arch-pnx4008/io.h b/include/asm-arm/arch-pnx4008/io.h new file mode 100644 index 00000000000..29ee43955c5 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/io.h @@ -0,0 +1,21 @@ + +/* + * include/asm-arm/arch-pnx4008/io.h + * + * Author: Dmitry Chigirev <chigirev@ru.mvista.com> + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#ifndef __ASM_ARM_ARCH_IO_H +#define __ASM_ARM_ARCH_IO_H + +#define IO_SPACE_LIMIT 0xffffffff + +#define __io(a) ((void __iomem *)(a)) +#define __mem_pci(a) (a) + +#endif diff --git a/include/asm-arm/arch-pnx4008/irq.h b/include/asm-arm/arch-pnx4008/irq.h new file mode 100644 index 00000000000..fabff5dc337 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/irq.h @@ -0,0 +1,42 @@ +/* + * include/asm-arm/arch-pnx4008/irq.h + * + * PNX4008 IRQ controller driver - header file + * this one is used in entry-arnv.S as well so it cannot contain C code + * + * Copyright (c) 2005 Philips Semiconductors + * Copyright (c) 2005 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef __PNX4008_IRQ_H__ +#define __PNX4008_IRQ_H__ + +#define MIC_VA_BASE IO_ADDRESS(PNX4008_INTCTRLMIC_BASE) +#define SIC1_VA_BASE IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE) +#define SIC2_VA_BASE IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE) + +/* Manual: Chapter 20, page 195 */ + +#define INTC_BIT(irq) (1<< ((irq) & 0x1F)) + +#define INTC_ER(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x0 + (((irq)&(0x3<<5))<<9))) +#define INTC_RSR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x4 + (((irq)&(0x3<<5))<<9))) +#define INTC_SR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x8 + (((irq)&(0x3<<5))<<9))) +#define INTC_APR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0xC + (((irq)&(0x3<<5))<<9))) +#define INTC_ATR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x10 + (((irq)&(0x3<<5))<<9))) +#define INTC_ITR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x14 + (((irq)&(0x3<<5))<<9))) + +#define START_INT_REG_BIT(irq) (1<<((irq)&0x1F)) + +#define START_INT_ER_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x20 + (((irq)&(0x1<<5))>>1))) +#define START_INT_RSR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x24 + (((irq)&(0x1<<5))>>1))) +#define START_INT_SR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x28 + (((irq)&(0x1<<5))>>1))) +#define START_INT_APR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x2C + (((irq)&(0x1<<5))>>1))) + +extern void __init pnx4008_init_irq(void); + +#endif /* __PNX4008_IRQ_H__ */ diff --git a/include/asm-arm/arch-pnx4008/irqs.h b/include/asm-arm/arch-pnx4008/irqs.h new file mode 100644 index 00000000000..13ec7ed0f50 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/irqs.h @@ -0,0 +1,215 @@ +/* + * include/asm-arm/arch-pnx4008/irqs.h + * + * PNX4008 IRQ controller driver - header file + * + * Author: Dmitry Chigirev <source@mvista.com> + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#ifndef __PNX4008_IRQS_h__ +#define __PNX4008_IRQS_h__ + +#define NR_IRQS 96 + +/*Manual: table 259, page 199*/ + +/*SUB2 Interrupt Routing (SIC2)*/ + +#define SIC2_BASE_INT 64 + +#define CLK_SWITCH_ARM_INT 95 /*manual: Clkswitch ARM */ +#define CLK_SWITCH_DSP_INT 94 /*manual: ClkSwitch DSP */ +#define CLK_SWITCH_AUD_INT 93 /*manual: Clkswitch AUD */ +#define GPI_06_INT 92 +#define GPI_05_INT 91 +#define GPI_04_INT 90 +#define GPI_03_INT 89 +#define GPI_02_INT 88 +#define GPI_01_INT 87 +#define GPI_00_INT 86 +#define BT_CLKREQ_INT 85 +#define SPI1_DATIN_INT 84 +#define U5_RX_INT 83 +#define SDIO_INT_N 82 +#define CAM_HS_INT 81 +#define CAM_VS_INT 80 +#define GPI_07_INT 79 +#define DISP_SYNC_INT 78 +#define DSP_INT8 77 +#define U7_HCTS_INT 76 +#define GPI_10_INT 75 +#define GPI_09_INT 74 +#define GPI_08_INT 73 +#define DSP_INT7 72 +#define U2_HCTS_INT 71 +#define SPI2_DATIN_INT 70 +#define GPIO_05_INT 69 +#define GPIO_04_INT 68 +#define GPIO_03_INT 67 +#define GPIO_02_INT 66 +#define GPIO_01_INT 65 +#define GPIO_00_INT 64 + +/*Manual: table 258, page 198*/ + +/*SUB1 Interrupt Routing (SIC1)*/ + +#define SIC1_BASE_INT 32 + +#define USB_I2C_INT 63 +#define USB_DEV_HP_INT 62 +#define USB_DEV_LP_INT 61 +#define USB_DEV_DMA_INT 60 +#define USB_HOST_INT 59 +#define USB_OTG_ATX_INT_N 58 +#define USB_OTG_TIMER_INT 57 +#define SW_INT 56 +#define SPI1_INT 55 +#define KEY_IRQ 54 +#define DSP_M_INT 53 +#define RTC_INT 52 +#define I2C_1_INT 51 +#define I2C_2_INT 50 +#define PLL1_LOCK_INT 49 +#define PLL2_LOCK_INT 48 +#define PLL3_LOCK_INT 47 +#define PLL4_LOCK_INT 46 +#define PLL5_LOCK_INT 45 +#define SPI2_INT 44 +#define DSP_INT1 43 +#define DSP_INT2 42 +#define DSP_TDM_INT2 41 +#define TS_AUX_INT 40 +#define TS_IRQ 39 +#define TS_P_INT 38 +#define UOUT1_TO_PAD_INT 37 +#define GPI_11_INT 36 +#define DSP_INT4 35 +#define JTAG_COMM_RX_INT 34 +#define JTAG_COMM_TX_INT 33 +#define DSP_INT3 32 + +/*Manual: table 257, page 197*/ + +/*MAIN Interrupt Routing*/ + +#define MAIN_BASE_INT 0 + +#define SUB2_FIQ_N 31 /*active low */ +#define SUB1_FIQ_N 30 /*active low */ +#define JPEG_INT 29 +#define DMA_INT 28 +#define MSTIMER_INT 27 +#define IIR1_INT 26 +#define IIR2_INT 25 +#define IIR7_INT 24 +#define DSP_TDM_INT0 23 +#define DSP_TDM_INT1 22 +#define DSP_P_INT 21 +#define DSP_INT0 20 +#define DUM_INT 19 +#define UOUT0_TO_PAD_INT 18 +#define MP4_ENC_INT 17 +#define MP4_DEC_INT 16 +#define SD0_INT 15 +#define MBX_INT 14 +#define SD1_INT 13 +#define MS_INT_N 12 +#define FLASH_INT 11 /*NAND*/ +#define IIR6_INT 10 +#define IIR5_INT 9 +#define IIR4_INT 8 +#define IIR3_INT 7 +#define WATCH_INT 6 +#define HSTIMER_INT 5 +#define ARCH_TIMER_IRQ HSTIMER_INT +#define CAM_INT 4 +#define PRNG_INT 3 +#define CRYPTO_INT 2 +#define SUB2_IRQ_N 1 /*active low */ +#define SUB1_IRQ_N 0 /*active low */ + +#define PNX4008_IRQ_TYPES \ +{ /*IRQ #'s: */ \ +IRQT_LOW, IRQT_LOW, IRQT_LOW, IRQT_HIGH, /* 0, 1, 2, 3 */ \ +IRQT_LOW, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 4, 5, 6, 7 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 8, 9,10,11 */ \ +IRQT_LOW, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 12,13,14,15 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 16,17,18,19 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 20,21,22,23 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 24,25,26,27 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_LOW, IRQT_LOW, /* 28,29,30,31 */ \ +IRQT_HIGH, IRQT_LOW, IRQT_HIGH, IRQT_HIGH, /* 32,33,34,35 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_FALLING, IRQT_HIGH, /* 36,37,38,39 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 40,41,42,43 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 44,45,46,47 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_LOW, IRQT_LOW, /* 48,49,50,51 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 52,53,54,55 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_LOW, IRQT_HIGH, /* 56,57,58,59 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 60,61,62,63 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 64,65,66,67 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 68,69,70,71 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 72,73,74,75 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 76,77,78,79 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 80,81,82,83 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 84,85,86,87 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 88,89,90,91 */ \ +IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, IRQT_HIGH, /* 92,93,94,95 */ \ +} + +/* Start Enable Pin Interrupts - table 58 page 66 */ + +#define SE_PIN_BASE_INT 32 + +#define SE_U7_RX_INT 63 +#define SE_U7_HCTS_INT 62 +#define SE_BT_CLKREQ_INT 61 +#define SE_U6_IRRX_INT 60 +/*59 unused*/ +#define SE_U5_RX_INT 58 +#define SE_GPI_11_INT 57 +#define SE_U3_RX_INT 56 +#define SE_U2_HCTS_INT 55 +#define SE_U2_RX_INT 54 +#define SE_U1_RX_INT 53 +#define SE_DISP_SYNC_INT 52 +/*51 unused*/ +#define SE_SDIO_INT_N 50 +#define SE_MSDIO_START_INT 49 +#define SE_GPI_06_INT 48 +#define SE_GPI_05_INT 47 +#define SE_GPI_04_INT 46 +#define SE_GPI_03_INT 45 +#define SE_GPI_02_INT 44 +#define SE_GPI_01_INT 43 +#define SE_GPI_00_INT 42 +#define SE_SYSCLKEN_PIN_INT 41 +#define SE_SPI1_DATAIN_INT 40 +#define SE_GPI_07_INT 39 +#define SE_SPI2_DATAIN_INT 38 +#define SE_GPI_10_INT 37 +#define SE_GPI_09_INT 36 +#define SE_GPI_08_INT 35 +/*34-32 unused*/ + +/* Start Enable Internal Interrupts - table 57 page 65 */ + +#define SE_INT_BASE_INT 0 + +#define SE_TS_IRQ 31 +#define SE_TS_P_INT 30 +#define SE_TS_AUX_INT 29 +/*27-28 unused*/ +#define SE_USB_AHB_NEED_CLK_INT 26 +#define SE_MSTIMER_INT 25 +#define SE_RTC_INT 24 +#define SE_USB_NEED_CLK_INT 23 +#define SE_USB_INT 22 +#define SE_USB_I2C_INT 21 +#define SE_USB_OTG_TIMER_INT 20 + +#endif /* __PNX4008_IRQS_h__ */ diff --git a/include/asm-arm/arch-pnx4008/memory.h b/include/asm-arm/arch-pnx4008/memory.h new file mode 100644 index 00000000000..0d8268a9526 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/memory.h @@ -0,0 +1,24 @@ +/* + * linux/include/asm-arm/arch-pnx4008/memory.h + * + * Copyright (c) 2005 Philips Semiconductors + * Copyright (c) 2005 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef __ASM_ARCH_MEMORY_H +#define __ASM_ARCH_MEMORY_H + +/* + * Physical DRAM offset. + */ +#define PHYS_OFFSET (0x80000000) + +#define __virt_to_bus(x) ((x) - PAGE_OFFSET + PHYS_OFFSET) +#define __bus_to_virt(x) ((x) + PAGE_OFFSET - PHYS_OFFSET) + +#endif diff --git a/include/asm-arm/arch-pnx4008/param.h b/include/asm-arm/arch-pnx4008/param.h new file mode 100644 index 00000000000..95d5f547b41 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/param.h @@ -0,0 +1,21 @@ +/* + * linux/include/asm-arm/arch-pnx4008/param.h + * + * Copyright (C) 1999 ARM Limited + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#define HZ 100 diff --git a/include/asm-arm/arch-pnx4008/platform.h b/include/asm-arm/arch-pnx4008/platform.h new file mode 100644 index 00000000000..485a3651b4d --- /dev/null +++ b/include/asm-arm/arch-pnx4008/platform.h @@ -0,0 +1,69 @@ +/* + * include/asm-arm/arch-pnx4008/platfrom.h + * + * PNX4008 Base addresses - header file + * + * Author: Dmitry Chigirev <source@mvista.com> + * + * Based on reference code received from Philips: + * Copyright (C) 2003 Philips Semiconductors + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + + +#ifndef __ASM_ARCH_PLATFORM_H__ +#define __ASM_ARCH_PLATFORM_H__ + +#define PNX4008_IRAM_BASE 0x08000000 +#define PNX4008_IRAM_SIZE 0x00010000 +#define PNX4008_YUV_SLAVE_BASE 0x10000000 +#define PNX4008_DUM_SLAVE_BASE 0x18000000 +#define PNX4008_NDF_FLASH_BASE 0x20020000 +#define PNX4008_SPI1_BASE 0x20088000 +#define PNX4008_SPI2_BASE 0x20090000 +#define PNX4008_SD_CONFIG_BASE 0x20098000 +#define PNX4008_FLASH_DATA 0x200B0000 +#define PNX4008_MLC_FLASH_BASE 0x200B8000 +#define PNX4008_JPEG_CONFIG_BASE 0x300A0000 +#define PNX4008_DMA_CONFIG_BASE 0x31000000 +#define PNX4008_USB_CONFIG_BASE 0x31020000 +#define PNX4008_SDRAM_CFG_BASE 0x31080000 +#define PNX4008_AHB2FAB_BASE 0x40000000 +#define PNX4008_PWRMAN_BASE 0x40004000 +#define PNX4008_INTCTRLMIC_BASE 0x40008000 +#define PNX4008_INTCTRLSIC1_BASE 0x4000C000 +#define PNX4008_INTCTRLSIC2_BASE 0x40010000 +#define PNX4008_HSUART1_BASE 0x40014000 +#define PNX4008_HSUART2_BASE 0x40018000 +#define PNX4008_HSUART7_BASE 0x4001C000 +#define PNX4008_RTC_BASE 0x40024000 +#define PNX4008_PIO_BASE 0x40028000 +#define PNX4008_MSTIMER_BASE 0x40034000 +#define PNX4008_HSTIMER_BASE 0x40038000 +#define PNX4008_WDOG_BASE 0x4003C000 +#define PNX4008_DEBUG_BASE 0x40040000 +#define PNX4008_TOUCH1_BASE 0x40048000 +#define PNX4008_KEYSCAN_BASE 0x40050000 +#define PNX4008_UARTCTRL_BASE 0x40054000 +#define PNX4008_PWM_BASE 0x4005C000 +#define PNX4008_UART3_BASE 0x40080000 +#define PNX4008_UART4_BASE 0x40088000 +#define PNX4008_UART5_BASE 0x40090000 +#define PNX4008_UART6_BASE 0x40098000 +#define PNX4008_I2C1_BASE 0x400A0000 +#define PNX4008_I2C2_BASE 0x400A8000 +#define PNX4008_MAGICGATE_BASE 0x400B0000 +#define PNX4008_DUMCONF_BASE 0x400B8000 +#define PNX4008_DUM_MAINCFG_BASE 0x400BC000 +#define PNX4008_DSP_BASE 0x400C0000 +#define PNX4008_PROFCOUNTER_BASE 0x400C8000 +#define PNX4008_CRYPTO_BASE 0x400D0000 +#define PNX4008_CAMIFCONF_BASE 0x400D8000 +#define PNX4008_YUV2RGB_BASE 0x400E0000 +#define PNX4008_AUDIOCONFIG_BASE 0x400E8000 + +#endif diff --git a/include/asm-arm/arch-pnx4008/pm.h b/include/asm-arm/arch-pnx4008/pm.h new file mode 100644 index 00000000000..c660486670f --- /dev/null +++ b/include/asm-arm/arch-pnx4008/pm.h @@ -0,0 +1,62 @@ +/* + * include/asm-arm/arch-pnx4008/pm.h + * + * PNX4008 Power Management Routiness - header file + * + * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com> + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#ifndef __ASM_ARCH_PNX4008_PM_H +#define __ASM_ARCH_PNX4008_PM_H + +#ifndef __ASSEMBLER__ +#include "irq.h" +#include "irqs.h" +#include "clock.h" + +extern void pnx4008_pm_idle(void); +extern void pnx4008_pm_suspend(void); +extern unsigned int pnx4008_cpu_suspend_sz; +extern void pnx4008_cpu_suspend(void); +extern unsigned int pnx4008_cpu_standby_sz; +extern void pnx4008_cpu_standby(void); + +extern int pnx4008_startup_pll(struct clk *); +extern int pnx4008_shutdown_pll(struct clk *); + +static inline void start_int_umask(u8 irq) +{ + __raw_writel(__raw_readl(START_INT_ER_REG(irq)) | + START_INT_REG_BIT(irq), START_INT_ER_REG(irq)); +} + +static inline void start_int_mask(u8 irq) +{ + __raw_writel(__raw_readl(START_INT_ER_REG(irq)) & + ~START_INT_REG_BIT(irq), START_INT_ER_REG(irq)); +} + +static inline void start_int_ack(u8 irq) +{ + __raw_writel(START_INT_REG_BIT(irq), START_INT_RSR_REG(irq)); +} + +static inline void start_int_set_falling_edge(u8 irq) +{ + __raw_writel(__raw_readl(START_INT_APR_REG(irq)) & + ~START_INT_REG_BIT(irq), START_INT_APR_REG(irq)); +} + +static inline void start_int_set_rising_edge(u8 irq) +{ + __raw_writel(__raw_readl(START_INT_APR_REG(irq)) | + START_INT_REG_BIT(irq), START_INT_APR_REG(irq)); +} + +#endif /* ASSEMBLER */ +#endif /* __ASM_ARCH_PNX4008_PM_H */ diff --git a/include/asm-arm/arch-pnx4008/system.h b/include/asm-arm/arch-pnx4008/system.h new file mode 100644 index 00000000000..6e3da70ab10 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/system.h @@ -0,0 +1,38 @@ +/* + * linux/include/asm-arm/arch-pnx4008/system.h + * + * Copyright (C) 2003 Philips Semiconductors + * Copyright (C) 2005 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#ifndef __ASM_ARCH_SYSTEM_H +#define __ASM_ARCH_SYSTEM_H + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/arch/platform.h> + +static void arch_idle(void) +{ + cpu_do_idle(); +} + +static inline void arch_reset(char mode) +{ + cpu_reset(0); +} + +#endif diff --git a/include/asm-arm/arch-pnx4008/timex.h b/include/asm-arm/arch-pnx4008/timex.h new file mode 100644 index 00000000000..ee470a39089 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/timex.h @@ -0,0 +1,73 @@ +/* + * include/asm-arm/arch-pnx4008/timex.h + * + * PNX4008 timers header file + * + * Author: Dmitry Chigirev <source@mvista.com> + * + * 2005 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#ifndef __PNX4008_TIMEX_H +#define __PNX4008_TIMEX_H + +#include <asm/hardware.h> +#include <asm/io.h> + +#define CLOCK_TICK_RATE 1000000 + +#define TICKS2USECS(x) (x) + +/* MilliSecond Timer - Chapter 21 Page 202 */ + +#define MSTIM_INT IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x0)) +#define MSTIM_CTRL IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x4)) +#define MSTIM_COUNTER IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x8)) +#define MSTIM_MCTRL IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x14)) +#define MSTIM_MATCH0 IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x18)) +#define MSTIM_MATCH1 IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x1c)) + +/* High Speed Timer - Chpater 22, Page 205 */ + +#define HSTIM_INT IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x0)) +#define HSTIM_CTRL IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x4)) +#define HSTIM_COUNTER IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x8)) +#define HSTIM_PMATCH IO_ADDRESS((PNX4008_HSTIMER_BASE + 0xC)) +#define HSTIM_PCOUNT IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x10)) +#define HSTIM_MCTRL IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x14)) +#define HSTIM_MATCH0 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x18)) +#define HSTIM_MATCH1 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x1c)) +#define HSTIM_MATCH2 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x20)) +#define HSTIM_CCR IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x28)) +#define HSTIM_CR0 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x2C)) +#define HSTIM_CR1 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x30)) + +/* IMPORTANT: both timers are UPCOUNTING */ + +/* xSTIM_MCTRL bit definitions */ +#define MR0_INT 1 +#define RESET_COUNT0 (1<<1) +#define STOP_COUNT0 (1<<2) +#define MR1_INT (1<<3) +#define RESET_COUNT1 (1<<4) +#define STOP_COUNT1 (1<<5) +#define MR2_INT (1<<6) +#define RESET_COUNT2 (1<<7) +#define STOP_COUNT2 (1<<8) + +/* xSTIM_CTRL bit definitions */ +#define COUNT_ENAB 1 +#define RESET_COUNT (1<<1) +#define DEBUG_EN (1<<2) + +/* xSTIM_INT bit definitions */ +#define MATCH0_INT 1 +#define MATCH1_INT (1<<1) +#define MATCH2_INT (1<<2) +#define RTC_TICK0 (1<<4) +#define RTC_TICK1 (1<<5) + +#endif diff --git a/include/asm-arm/arch-pnx4008/uncompress.h b/include/asm-arm/arch-pnx4008/uncompress.h new file mode 100644 index 00000000000..8fa4d24b72b --- /dev/null +++ b/include/asm-arm/arch-pnx4008/uncompress.h @@ -0,0 +1,46 @@ +/* + * linux/include/asm-arm/arch-pnx4008/uncompress.h + * + * Copyright (C) 1999 ARM Limited + * Copyright (C) 2006 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#define UART5_BASE 0x40090000 + +#define UART5_DR (*(volatile unsigned char *) (UART5_BASE)) +#define UART5_FR (*(volatile unsigned char *) (UART5_BASE + 18)) + +static __inline__ void putc(char c) +{ + while (UART5_FR & (1 << 5)) + barrier(); + + UART5_DR = c; +} + +/* + * This does not append a newline + */ +static inline void flush(void) +{ +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/include/asm-arm/arch-pnx4008/vmalloc.h b/include/asm-arm/arch-pnx4008/vmalloc.h new file mode 100644 index 00000000000..140d925f6f3 --- /dev/null +++ b/include/asm-arm/arch-pnx4008/vmalloc.h @@ -0,0 +1,20 @@ +/* + * include/asm-arm/arch-pnx4008/vmalloc.h + * + * Author: Vitaly Wool <source@mvista.com> + * + * 2006 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +/* + * Just any arbitrary offset to the start of the vmalloc VM area: the + * current 8MB value just means that there will be a 8MB "hole" after the + * physical memory until the kernel virtual memory starts. That means that + * any out-of-bounds memory accesses will hopefully be caught. + * The vmalloc() routines leaves a hole of 4kB between each vmalloced + * area for the same reason. ;) + */ +#define VMALLOC_END (PAGE_OFFSET + 0x10000000) diff --git a/include/asm-arm/arch-s3c2410/map.h b/include/asm-arm/arch-s3c2410/map.h index c380d264a84..5e4c8c37bc6 100644 --- a/include/asm-arm/arch-s3c2410/map.h +++ b/include/asm-arm/arch-s3c2410/map.h @@ -126,9 +126,18 @@ #define S3C24XX_SZ_IIS SZ_1M /* GPIO ports */ -#define S3C24XX_VA_GPIO S3C2410_ADDR(0x00E00000) + +/* the calculation for the VA of this must ensure that + * it is the same distance apart from the UART in the + * phsyical address space, as the initial mapping for the IO + * is done as a 1:1 maping. This puts it (currently) at + * 0xF6800000, which is not in the way of any current mapping + * by the base system. +*/ + #define S3C2400_PA_GPIO (0x15600000) #define S3C2410_PA_GPIO (0x56000000) +#define S3C24XX_VA_GPIO ((S3C2410_PA_GPIO - S3C24XX_PA_UART) + S3C24XX_VA_UART) #define S3C24XX_SZ_GPIO SZ_1M /* RTC */ diff --git a/include/asm-arm/arch-s3c2410/regs-clock.h b/include/asm-arm/arch-s3c2410/regs-clock.h index 34360706e01..6c92faffe98 100644 --- a/include/asm-arm/arch-s3c2410/regs-clock.h +++ b/include/asm-arm/arch-s3c2410/regs-clock.h @@ -114,7 +114,7 @@ s3c2410_get_pll(unsigned int pllval, unsigned int baseclk) #endif /* __ASSEMBLY__ */ -#ifdef CONFIG_CPU_S3C2440 +#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) /* extra registers */ #define S3C2440_CAMDIVN S3C2410_CLKREG(0x18) @@ -136,7 +136,9 @@ s3c2410_get_pll(unsigned int pllval, unsigned int baseclk) #define S3C2440_CAMDIVN_HCLK4_HALF (1<<9) #define S3C2440_CAMDIVN_DVSEN (1<<12) -#endif /* CONFIG_CPU_S3C2440 */ +#define S3C2442_CAMDIVN_CAMCLK_DIV3 (1<<5) + +#endif /* CONFIG_CPU_S3C2440 or CONFIG_CPU_S3C2442 */ #endif /* __ASM_ARM_REGS_CLOCK */ diff --git a/include/asm-arm/arch-s3c2410/regs-gpio.h b/include/asm-arm/arch-s3c2410/regs-gpio.h index d2574084697..5f10334f06b 100644 --- a/include/asm-arm/arch-s3c2410/regs-gpio.h +++ b/include/asm-arm/arch-s3c2410/regs-gpio.h @@ -450,12 +450,14 @@ #define S3C2410_GPD0_OUTP (0x01 << 0) #define S3C2410_GPD0_VD8 (0x02 << 0) #define S3C2400_GPD0_VFRAME (0x02 << 0) +#define S3C2442_GPD0_nSPICS1 (0x03 << 0) #define S3C2410_GPD1 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 1) #define S3C2410_GPD1_INP (0x00 << 2) #define S3C2410_GPD1_OUTP (0x01 << 2) #define S3C2410_GPD1_VD9 (0x02 << 2) #define S3C2400_GPD1_VM (0x02 << 2) +#define S3C2442_GPD1_SPICLK1 (0x03 << 2) #define S3C2410_GPD2 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 2) #define S3C2410_GPD2_INP (0x00 << 4) @@ -858,6 +860,7 @@ #define S3C2410_GPG12_OUTP (0x01 << 24) #define S3C2410_GPG12_EINT20 (0x02 << 24) #define S3C2410_GPG12_XMON (0x03 << 24) +#define S3C2442_GPG12_nSPICS0 (0x03 << 24) #define S3C2410_GPG13 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 13) #define S3C2410_GPG13_INP (0x00 << 26) @@ -943,6 +946,7 @@ #define S3C2410_GPH9_INP (0x00 << 18) #define S3C2410_GPH9_OUTP (0x01 << 18) #define S3C2410_GPH9_CLKOUT0 (0x02 << 18) +#define S3C2442_GPH9_nSPICS0 (0x03 << 18) #define S3C2410_GPH10 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 10) #define S3C2410_GPH10_INP (0x00 << 20) @@ -1051,6 +1055,7 @@ #define S3C2410_GSTATUS1_IDMASK (0xffff0000) #define S3C2410_GSTATUS1_2410 (0x32410000) #define S3C2410_GSTATUS1_2440 (0x32440000) +#define S3C2410_GSTATUS1_2442 (0x32440aaa) #define S3C2410_GSTATUS2_WTRESET (1<<2) #define S3C2410_GSTATUS2_OFFRESET (1<<1) diff --git a/include/asm-arm/arch-s3c2410/uncompress.h b/include/asm-arm/arch-s3c2410/uncompress.h index a6f6a0e44af..bbd9ee1ff75 100644 --- a/include/asm-arm/arch-s3c2410/uncompress.h +++ b/include/asm-arm/arch-s3c2410/uncompress.h @@ -82,7 +82,8 @@ static void putc(int ch) while (1) { level = uart_rd(S3C2410_UFSTAT); - if (cpuid == S3C2410_GSTATUS1_2440) { + if (cpuid == S3C2410_GSTATUS1_2440 || + cpuid == S3C2410_GSTATUS1_2442) { level &= S3C2440_UFSTAT_TXMASK; level >>= S3C2440_UFSTAT_TXSHIFT; } else { @@ -130,7 +131,7 @@ static void arch_decomp_wdog_start(void) { __raw_writel(WDOG_COUNT, S3C2410_WTDAT); __raw_writel(WDOG_COUNT, S3C2410_WTCNT); - __raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x40), S3C2410_WTCON); + __raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x80), S3C2410_WTCON); } #else diff --git a/include/asm-arm/mach/time.h b/include/asm-arm/mach/time.h index 96c6db7dd0e..9f28073559e 100644 --- a/include/asm-arm/mach/time.h +++ b/include/asm-arm/mach/time.h @@ -50,6 +50,7 @@ struct sys_timer { #define DYN_TICK_ENABLED (1 << 1) struct dyn_tick_timer { + spinlock_t lock; unsigned int state; /* Current state */ int (*enable)(void); /* Enables dynamic tick */ int (*disable)(void); /* Disables dynamic tick */ |