diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/hwmon/ds1621 | 51 | ||||
| -rw-r--r-- | Documentation/hwmon/pcf8591 (renamed from Documentation/i2c/chips/pcf8591) | 0 | ||||
| -rw-r--r-- | Documentation/hwmon/sysfs-interface | 22 | ||||
| -rw-r--r-- | Documentation/hwmon/w83627ehf | 29 |
4 files changed, 45 insertions, 57 deletions
diff --git a/Documentation/hwmon/ds1621 b/Documentation/hwmon/ds1621 index 1fee6f1e6bc..5e97f333c4d 100644 --- a/Documentation/hwmon/ds1621 +++ b/Documentation/hwmon/ds1621 @@ -49,12 +49,9 @@ of up to +/- 0.5 degrees even when compared against precise temperature readings. Be sure to have a high vs. low temperature limit gap of al least 1.0 degree Celsius to avoid Tout "bouncing", though! -As for alarms, you can read the alarm status of the DS1621 via the 'alarms' -/sys file interface. The result consists mainly of bit 6 and 5 of the -configuration register of the chip; bit 6 (0x40 or 64) is the high alarm -bit and bit 5 (0x20 or 32) the low one. These bits are set when the high or -low limits are met or exceeded and are reset by the module as soon as the -respective temperature ranges are left. +The alarm bits are set when the high or low limits are met or exceeded and +are reset by the module as soon as the respective temperature ranges are +left. The alarm registers are in no way suitable to find out about the actual status of Tout. They will only tell you about its history, whether or not @@ -64,45 +61,3 @@ with neither of the alarms set. Temperature conversion of the DS1621 takes up to 1000ms; internal access to non-volatile registers may last for 10ms or below. - -High Accuracy Temperature Reading ---------------------------------- - -As said before, the temperature issued via the 9-bit i2c-bus data is -somewhat arbitrary. Internally, the temperature conversion is of a -different kind that is explained (not so...) well in the DS1621 data sheet. -To cut the long story short: Inside the DS1621 there are two oscillators, -both of them biassed by a temperature coefficient. - -Higher resolution of the temperature reading can be achieved using the -internal projection, which means taking account of REG_COUNT and REG_SLOPE -(the driver manages them): - -Taken from Dallas Semiconductors App Note 068: 'Increasing Temperature -Resolution on the DS1620' and App Note 105: 'High Resolution Temperature -Measurement with Dallas Direct-to-Digital Temperature Sensors' - -- Read the 9-bit temperature and strip the LSB (Truncate the .5 degs) -- The resulting value is TEMP_READ. -- Then, read REG_COUNT. -- And then, REG_SLOPE. - - TEMP = TEMP_READ - 0.25 + ((REG_SLOPE - REG_COUNT) / REG_SLOPE) - -Note that this is what the DONE bit in the DS1621 configuration register is -good for: Internally, one temperature conversion takes up to 1000ms. Before -that conversion is complete you will not be able to read valid things out -of REG_COUNT and REG_SLOPE. The DONE bit, as you may have guessed by now, -tells you whether the conversion is complete ("done", in plain English) and -thus, whether the values you read are good or not. - -The DS1621 has two modes of operation: "Continuous" conversion, which can -be understood as the default stand-alone mode where the chip gets the -temperature and controls external devices via its Tout pin or tells other -i2c's about it if they care. The other mode is called "1SHOT", that means -that it only figures out about the temperature when it is explicitly told -to do so; this can be seen as power saving mode. - -Now if you want to read REG_COUNT and REG_SLOPE, you have to either stop -the continuous conversions until the contents of these registers are valid, -or, in 1SHOT mode, you have to have one conversion made. diff --git a/Documentation/i2c/chips/pcf8591 b/Documentation/hwmon/pcf8591 index 5628fcf4207..5628fcf4207 100644 --- a/Documentation/i2c/chips/pcf8591 +++ b/Documentation/hwmon/pcf8591 diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index 6dbfd5efd99..2f10ce6a879 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -365,6 +365,7 @@ energy[1-*]_input Cumulative energy use Unit: microJoule RO + ********** * Alarms * ********** @@ -453,6 +454,27 @@ beep_mask Bitmask for beep. RW +*********************** +* Intrusion detection * +*********************** + +intrusion[0-*]_alarm + Chassis intrusion detection + 0: OK + 1: intrusion detected + RW + Contrary to regular alarm flags which clear themselves + automatically when read, this one sticks until cleared by + the user. This is done by writing 0 to the file. Writing + other values is unsupported. + +intrusion[0-*]_beep + Chassis intrusion beep + 0: disable + 1: enable + RW + + sysfs attribute writes interpretation ------------------------------------- diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf index d6e1ae30fa6..b6eb59384bb 100644 --- a/Documentation/hwmon/w83627ehf +++ b/Documentation/hwmon/w83627ehf @@ -2,30 +2,40 @@ Kernel driver w83627ehf ======================= Supported chips: - * Winbond W83627EHF/EHG/DHG (ISA access ONLY) + * Winbond W83627EHF/EHG (ISA access ONLY) Prefix: 'w83627ehf' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: - http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83627EHF_%20W83627EHGb.pdf - DHG datasheet confidential. + http://www.nuvoton.com.tw/NR/rdonlyres/A6A258F0-F0C9-4F97-81C0-C4D29E7E943E/0/W83627EHF.pdf + * Winbond W83627DHG + Prefix: 'w83627dhg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: + http://www.nuvoton.com.tw/NR/rdonlyres/7885623D-A487-4CF9-A47F-30C5F73D6FE6/0/W83627DHG.pdf + * Winbond W83667HG + Prefix: 'w83667hg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: not available Authors: Jean Delvare <khali@linux-fr.org> Yuan Mu (Winbond) Rudolf Marek <r.marek@assembler.cz> David Hubbard <david.c.hubbard@gmail.com> + Gong Jun <JGong@nuvoton.com> Description ----------- -This driver implements support for the Winbond W83627EHF, W83627EHG, and -W83627DHG super I/O chips. We will refer to them collectively as Winbond chips. +This driver implements support for the Winbond W83627EHF, W83627EHG, +W83627DHG and W83667HG super I/O chips. We will refer to them collectively +as Winbond chips. The chips implement three temperature sensors, five fan rotation speed sensors, ten analog voltage sensors (only nine for the 627DHG), one -VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG), alarms with beep -warnings (control unimplemented), and some automatic fan regulation -strategies (plus manual fan control mode). +VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG and 667HG), alarms +with beep warnings (control unimplemented), and some automatic fan +regulation strategies (plus manual fan control mode). Temperatures are measured in degrees Celsius and measurement resolution is 1 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when @@ -54,7 +64,8 @@ follows: temp1 -> pwm1 temp2 -> pwm2 temp3 -> pwm3 -prog -> pwm4 (the programmable setting is not supported by the driver) +prog -> pwm4 (not on 667HG; the programmable setting is not supported by + the driver) /sys files ---------- |