diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/dontdiff | 1 | ||||
-rw-r--r-- | Documentation/hwmon/k10temp | 60 | ||||
-rw-r--r-- | Documentation/kbuild/kbuild.txt | 14 | ||||
-rw-r--r-- | Documentation/kbuild/kconfig.txt | 8 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/nintendo/gamecube.txt | 109 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/nintendo/wii.txt | 184 |
6 files changed, 375 insertions, 1 deletions
diff --git a/Documentation/dontdiff b/Documentation/dontdiff index e151b2a3626..3ad6acead94 100644 --- a/Documentation/dontdiff +++ b/Documentation/dontdiff @@ -103,6 +103,7 @@ gconf gen-devlist gen_crc32table gen_init_cpio +generated genheaders genksyms *_gray256.c diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp new file mode 100644 index 00000000000..a7a18d453a5 --- /dev/null +++ b/Documentation/hwmon/k10temp @@ -0,0 +1,60 @@ +Kernel driver k10temp +===================== + +Supported chips: +* AMD Family 10h processors: + Socket F: Quad-Core/Six-Core/Embedded Opteron + Socket AM2+: Opteron, Phenom (II) X3/X4 + Socket AM3: Quad-Core Opteron, Athlon/Phenom II X2/X3/X4, Sempron II + Socket S1G3: Athlon II, Sempron, Turion II +* AMD Family 11h processors: + Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra) + + Prefix: 'k10temp' + Addresses scanned: PCI space + Datasheets: + BIOS and Kernel Developer's Guide (BKDG) For AMD Family 10h Processors: + http://support.amd.com/us/Processor_TechDocs/31116.pdf + BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors: + http://support.amd.com/us/Processor_TechDocs/41256.pdf + Revision Guide for AMD Family 10h Processors: + http://support.amd.com/us/Processor_TechDocs/41322.pdf + Revision Guide for AMD Family 11h Processors: + http://support.amd.com/us/Processor_TechDocs/41788.pdf + AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks: + http://support.amd.com/us/Processor_TechDocs/43373.pdf + AMD Family 10h Server and Workstation Processor Power and Thermal Data Sheet: + http://support.amd.com/us/Processor_TechDocs/43374.pdf + AMD Family 10h Desktop Processor Power and Thermal Data Sheet: + http://support.amd.com/us/Processor_TechDocs/43375.pdf + +Author: Clemens Ladisch <clemens@ladisch.de> + +Description +----------- + +This driver permits reading of the internal temperature sensor of AMD +Family 10h and 11h processors. + +All these processors have a sensor, but on older revisions of Family 10h +processors, the sensor may return inconsistent values (erratum 319). The +driver will refuse to load on these revisions unless you specify the +"force=1" module parameter. + +There is one temperature measurement value, available as temp1_input in +sysfs. It is measured in degrees Celsius with a resolution of 1/8th degree. +Please note that it is defined as a relative value; to quote the AMD manual: + + Tctl is the processor temperature control value, used by the platform to + control cooling systems. Tctl is a non-physical temperature on an + arbitrary scale measured in degrees. It does _not_ represent an actual + physical temperature like die or case temperature. Instead, it specifies + the processor temperature relative to the point at which the system must + supply the maximum cooling for the processor's specified maximum case + temperature and maximum thermal power dissipation. + +The maximum value for Tctl is available in the file temp1_max. + +If the BIOS has enabled hardware temperature control, the threshold at +which the processor will throttle itself to avoid damage is available in +temp1_crit and temp1_crit_hyst. diff --git a/Documentation/kbuild/kbuild.txt b/Documentation/kbuild/kbuild.txt index bb3bf38f03d..6f8c1cabbc5 100644 --- a/Documentation/kbuild/kbuild.txt +++ b/Documentation/kbuild/kbuild.txt @@ -1,3 +1,17 @@ +Output files + +modules.order +-------------------------------------------------- +This file records the order in which modules appear in Makefiles. This +is used by modprobe to deterministically resolve aliases that match +multiple modules. + +modules.builtin +-------------------------------------------------- +This file lists all modules that are built into the kernel. This is used +by modprobe to not fail when trying to load something builtin. + + Environment variables KCPPFLAGS diff --git a/Documentation/kbuild/kconfig.txt b/Documentation/kbuild/kconfig.txt index 849b5e56d06..49efae70397 100644 --- a/Documentation/kbuild/kconfig.txt +++ b/Documentation/kbuild/kconfig.txt @@ -103,10 +103,16 @@ KCONFIG_AUTOCONFIG This environment variable can be set to specify the path & name of the "auto.conf" file. Its default value is "include/config/auto.conf". +KCONFIG_TRISTATE +-------------------------------------------------- +This environment variable can be set to specify the path & name of the +"tristate.conf" file. Its default value is "include/config/tristate.conf". + KCONFIG_AUTOHEADER -------------------------------------------------- This environment variable can be set to specify the path & name of the -"autoconf.h" (header) file. Its default value is "include/linux/autoconf.h". +"autoconf.h" (header) file. +Its default value is "include/generated/autoconf.h". ====================================================================== diff --git a/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt new file mode 100644 index 00000000000..b558585b1aa --- /dev/null +++ b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt @@ -0,0 +1,109 @@ + +Nintendo GameCube device tree +============================= + +1) The "flipper" node + + This node represents the multi-function "Flipper" chip, which packages + many of the devices found in the Nintendo GameCube. + + Required properties: + + - compatible : Should be "nintendo,flipper" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the interrupt controller within the "Flipper" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - compatible : should be "nintendo,flipper-pic" + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.c.i) The Auxiliary RAM (ARAM) node + + Represents the non cpu-addressable ram designed mainly to store audio + related information. + The ARAM node must be placed under the DSP node. + + Required properties: + + - compatible : should be "nintendo,flipper-aram" + - reg : should contain the ARAM start (zero-based) and length + +1.d) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,flipper-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.g) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + diff --git a/Documentation/powerpc/dts-bindings/nintendo/wii.txt b/Documentation/powerpc/dts-bindings/nintendo/wii.txt new file mode 100644 index 00000000000..a7e155a023b --- /dev/null +++ b/Documentation/powerpc/dts-bindings/nintendo/wii.txt @@ -0,0 +1,184 @@ + +Nintendo Wii device tree +======================== + +0) The root node + + This node represents the Nintendo Wii video game console. + + Required properties: + + - model : Should be "nintendo,wii" + - compatible : Should be "nintendo,wii" + +1) The "hollywood" node + + This node represents the multi-function "Hollywood" chip, which packages + many of the devices found in the Nintendo Wii. + + Required properties: + + - compatible : Should be "nintendo,hollywood" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,hollywood-vi","nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,hollywood-pi","nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the "Flipper" interrupt controller within the "Hollywood" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,flipper-pic" + - interrupt-controller + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,hollywood-dsp","nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.d) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-si","nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,hollywood-ai","nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-exi","nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + +1.g) The Open Host Controller Interface (OHCI) nodes + + Represent the USB 1.x Open Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ohci","usb-ohci" + - reg : should contain the OHCI registers location and length + - interrupts : should contain the OHCI interrupt + +1.h) The Enhanced Host Controller Interface (EHCI) node + + Represents the USB 2.0 Enhanced Host Controller Interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ehci","usb-ehci" + - reg : should contain the EHCI registers location and length + - interrupts : should contain the EHCI interrupt + +1.i) The Secure Digital Host Controller Interface (SDHCI) nodes + + Represent the Secure Digital Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-sdhci","sdhci" + - reg : should contain the SDHCI registers location and length + - interrupts : should contain the SDHCI interrupt + +1.j) The Inter-Processsor Communication (IPC) node + + Represent the Inter-Processor Communication interface. This interface + enables communications between the Broadway and the Starlet processors. + + - compatible : should be "nintendo,hollywood-ipc" + - reg : should contain the IPC registers location and length + - interrupts : should contain the IPC interrupt + +1.k) The "Hollywood" interrupt controller node + + Represents the "Hollywood" interrupt controller within the + "Hollywood" chip. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,hollywood-pic" + - reg : should contain the controller registers location and length + - interrupt-controller + - interrupts : should contain the cascade interrupt of the "flipper" pic + - interrupt-parent: should contain the phandle of the "flipper" pic + +1.l) The General Purpose I/O (GPIO) controller node + + Represents the dual access 32 GPIO controller interface. + + Required properties: + + - #gpio-cells : <2> + - compatible : should be "nintendo,hollywood-gpio" + - reg : should contain the IPC registers location and length + - gpio-controller + +1.m) The control node + + Represents the control interface used to setup several miscellaneous + settings of the "Hollywood" chip like boot memory mappings, resets, + disk interface mode, etc. + + Required properties: + + - compatible : should be "nintendo,hollywood-control" + - reg : should contain the control registers location and length + +1.n) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,hollywood-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + |