diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/feature-removal-schedule.txt | 10 | ||||
| -rw-r--r-- | Documentation/gpio.txt | 23 |
2 files changed, 19 insertions, 14 deletions
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index d0f35467064..a23361e80c6 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -255,6 +255,16 @@ Who: Jan Engelhardt <jengelh@computergmbh.de> --------------------------- +What: GPIO autorequest on gpio_direction_{input,output}() in gpiolib +When: February 2010 +Why: All callers should use explicit gpio_request()/gpio_free(). + The autorequest mechanism in gpiolib was provided mostly as a + migration aid for legacy GPIO interfaces (for SOC based GPIOs). + Those users have now largely migrated. Platforms implementing + the GPIO interfaces without using gpiolib will see no changes. +Who: David Brownell <dbrownell@users.sourceforge.net> +--------------------------- + What: b43 support for firmware revision < 410 When: The schedule was July 2008, but it was decided that we are going to keep the code as long as there are no major maintanance headaches. diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt index b1b98870124..145c25a170c 100644 --- a/Documentation/gpio.txt +++ b/Documentation/gpio.txt @@ -123,7 +123,10 @@ platform-specific implementation issue. Using GPIOs ----------- -One of the first things to do with a GPIO, often in board setup code when +The first thing a system should do with a GPIO is allocate it, using +the gpio_request() call; see later. + +One of the next things to do with a GPIO, often in board setup code when setting up a platform_device using the GPIO, is mark its direction: /* set as input or output, returning 0 or negative errno */ @@ -141,8 +144,8 @@ This helps avoid signal glitching during system startup. For compatibility with legacy interfaces to GPIOs, setting the direction of a GPIO implicitly requests that GPIO (see below) if it has not been -requested already. That compatibility may be removed in the future; -explicitly requesting GPIOs is strongly preferred. +requested already. That compatibility is being removed from the optional +gpiolib framework. Setting the direction can fail if the GPIO number is invalid, or when that particular GPIO can't be used in that mode. It's generally a bad @@ -195,7 +198,7 @@ This requires sleeping, which can't be done from inside IRQ handlers. Platforms that support this type of GPIO distinguish them from other GPIOs by returning nonzero from this call (which requires a valid GPIO number, -either explicitly or implicitly requested): +which should have been previously allocated with gpio_request): int gpio_cansleep(unsigned gpio); @@ -212,10 +215,9 @@ for GPIOs that can't be accessed from IRQ handlers, these calls act the same as the spinlock-safe calls. -Claiming and Releasing GPIOs (OPTIONAL) ---------------------------------------- +Claiming and Releasing GPIOs +---------------------------- To help catch system configuration errors, two calls are defined. -However, many platforms don't currently support this mechanism. /* request GPIO, returning 0 or negative errno. * non-null labels may be useful for diagnostics. @@ -244,13 +246,6 @@ Some platforms may also use knowledge about what GPIOs are active for power management, such as by powering down unused chip sectors and, more easily, gating off unused clocks. -These two calls are optional because not not all current Linux platforms -offer such functionality in their GPIO support; a valid implementation -could return success for all gpio_request() calls. Unlike the other calls, -the state they represent doesn't normally match anything from a hardware -register; it's just a software bitmap which clearly is not necessary for -correct operation of hardware or (bug free) drivers. - Note that requesting a GPIO does NOT cause it to be configured in any way; it just marks that GPIO as in use. Separate code must handle any pin setup (e.g. controlling which pin the GPIO uses, pullup/pulldown). |