diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/hwmon/w83627hf | 4 | ||||
| -rw-r--r-- | Documentation/hwmon/w83781d | 24 | ||||
| -rw-r--r-- | Documentation/i2c/busses/i2c-piix4 | 2 | ||||
| -rw-r--r-- | Documentation/i2c/busses/scx200_acb | 5 |
4 files changed, 32 insertions, 3 deletions
diff --git a/Documentation/hwmon/w83627hf b/Documentation/hwmon/w83627hf index bbeaba68044..79223192124 100644 --- a/Documentation/hwmon/w83627hf +++ b/Documentation/hwmon/w83627hf @@ -18,6 +18,10 @@ Supported chips: Prefix: 'w83637hf' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: http://www.winbond.com/PDF/sheet/w83637hf.pdf + * Winbond W83687THF + Prefix: 'w83687thf' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Provided by Winbond on request Authors: Frodo Looijaard <frodol@dds.nl>, diff --git a/Documentation/hwmon/w83781d b/Documentation/hwmon/w83781d index e5459333ba6..b1e9f80098e 100644 --- a/Documentation/hwmon/w83781d +++ b/Documentation/hwmon/w83781d @@ -36,6 +36,11 @@ Module parameters Use 'init=0' to bypass initializing the chip. Try this if your computer crashes when you load the module. +* reset int + (default 0) + The driver used to reset the chip on load, but does no more. Use + 'reset=1' to restore the old behavior. Report if you need to do this. + force_subclients=bus,caddr,saddr,saddr This is used to force the i2c addresses for subclients of a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b' @@ -123,6 +128,25 @@ When an alarm goes off, you can be warned by a beeping signal through your computer speaker. It is possible to enable all beeping globally, or only the beeping for some alarms. +Individual alarm and beep bits: + +0x000001: in0 +0x000002: in1 +0x000004: in2 +0x000008: in3 +0x000010: temp1 +0x000020: temp2 (+temp3 on W83781D) +0x000040: fan1 +0x000080: fan2 +0x000100: in4 +0x000200: in5 +0x000400: in6 +0x000800: fan3 +0x001000: chassis +0x002000: temp3 (W83782D and W83627HF only) +0x010000: in7 (W83782D and W83627HF only) +0x020000: in8 (W83782D and W83627HF only) + If an alarm triggers, it will remain triggered until the hardware register is read at least once. This means that the cause for the alarm may already have disappeared! Note that in the current implementation, all diff --git a/Documentation/i2c/busses/i2c-piix4 b/Documentation/i2c/busses/i2c-piix4 index 856b4b8b962..a1c8f581afe 100644 --- a/Documentation/i2c/busses/i2c-piix4 +++ b/Documentation/i2c/busses/i2c-piix4 @@ -4,7 +4,7 @@ Supported adapters: * Intel 82371AB PIIX4 and PIIX4E * Intel 82443MX (440MX) Datasheet: Publicly available at the Intel website - * ServerWorks OSB4, CSB5 and CSB6 southbridges + * ServerWorks OSB4, CSB5, CSB6 and HT-1000 southbridges Datasheet: Only available via NDA from ServerWorks * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge Datasheet: Publicly available at the SMSC website http://www.smsc.com diff --git a/Documentation/i2c/busses/scx200_acb b/Documentation/i2c/busses/scx200_acb index 08c8cd1df60..f50e69981ec 100644 --- a/Documentation/i2c/busses/scx200_acb +++ b/Documentation/i2c/busses/scx200_acb @@ -6,9 +6,10 @@ Module Parameters ----------------- * base: int - Base addresses for the ACCESS.bus controllers + Base addresses for the ACCESS.bus controllers on SCx200 and SC1100 devices Description ----------- -Enable the use of the ACCESS.bus controllers of a SCx200 processor. +Enable the use of the ACCESS.bus controller on the Geode SCx200 and +SC1100 processors and the CS5535 and CS5536 Geode companion devices. |