diff options
Diffstat (limited to 'arch/arm')
166 files changed, 10054 insertions, 5470 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index a930e5c5672..c52f6909f65 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -299,6 +299,7 @@ config ARCH_MXC select ARCH_MTD_XIP select GENERIC_GPIO select ARCH_REQUIRE_GPIOLIB + select HAVE_CLK help Support for Freescale MXC/iMX-based family of processors @@ -318,15 +319,6 @@ config ARCH_H720X help This enables support for systems based on the Hynix HMS720x -config ARCH_IMX - bool "IMX" - select CPU_ARM920T - select GENERIC_GPIO - select GENERIC_TIME - select GENERIC_CLOCKEVENTS - help - Support for Motorola's i.MX family of processors (MX1, MXL). - config ARCH_IOP13XX bool "IOP13xx-based" depends on MMU @@ -507,8 +499,6 @@ config ARCH_PXA select HAVE_CLK select COMMON_CLKDEV select ARCH_REQUIRE_GPIOLIB - select HAVE_CLK - select COMMON_CLKDEV select GENERIC_TIME select GENERIC_CLOCKEVENTS select TICK_ONESHOT @@ -603,6 +593,8 @@ config ARCH_DAVINCI select ARCH_REQUIRE_GPIOLIB select HAVE_CLK select ZONE_DMA + select HAVE_IDE + select COMMON_CLKDEV help Support for TI's DaVinci platform. @@ -681,8 +673,6 @@ endif source "arch/arm/mach-lh7a40x/Kconfig" -source "arch/arm/mach-imx/Kconfig" - source "arch/arm/mach-h720x/Kconfig" source "arch/arm/mach-versatile/Kconfig" @@ -740,6 +730,56 @@ if !MMU source "arch/arm/Kconfig-nommu" endif +config ARM_ERRATA_411920 + bool "ARM errata: Invalidation of the Instruction Cache operation can fail" + depends on CPU_V6 && !SMP + help + Invalidation of the Instruction Cache operation can + fail. This erratum is present in 1136 (before r1p4), 1156 and 1176. + It does not affect the MPCore. This option enables the ARM Ltd. + recommended workaround. + +config ARM_ERRATA_430973 + bool "ARM errata: Stale prediction on replaced interworking branch" + depends on CPU_V7 + help + This option enables the workaround for the 430973 Cortex-A8 + (r1p0..r1p2) erratum. If a code sequence containing an ARM/Thumb + interworking branch is replaced with another code sequence at the + same virtual address, whether due to self-modifying code or virtual + to physical address re-mapping, Cortex-A8 does not recover from the + stale interworking branch prediction. This results in Cortex-A8 + executing the new code sequence in the incorrect ARM or Thumb state. + The workaround enables the BTB/BTAC operations by setting ACTLR.IBE + and also flushes the branch target cache at every context switch. + Note that setting specific bits in the ACTLR register may not be + available in non-secure mode. + +config ARM_ERRATA_458693 + bool "ARM errata: Processor deadlock when a false hazard is created" + depends on CPU_V7 + help + This option enables the workaround for the 458693 Cortex-A8 (r2p0) + erratum. For very specific sequences of memory operations, it is + possible for a hazard condition intended for a cache line to instead + be incorrectly associated with a different cache line. This false + hazard might then cause a processor deadlock. The workaround enables + the L1 caching of the NEON accesses and disables the PLD instruction + in the ACTLR register. Note that setting specific bits in the ACTLR + register may not be available in non-secure mode. + +config ARM_ERRATA_460075 + bool "ARM errata: Data written to the L2 cache can be overwritten with stale data" + depends on CPU_V7 + help + This option enables the workaround for the 460075 Cortex-A8 (r2p0) + erratum. Any asynchronous access to the L2 cache may encounter a + situation in which recent store transactions to the L2 cache are lost + and overwritten with stale memory contents from external memory. The + workaround disables the write-allocate mode for the L2 cache via the + ACTLR register. Note that setting specific bits in the ACTLR register + may not be available in non-secure mode. + endmenu source "arch/arm/common/Kconfig" @@ -971,7 +1011,7 @@ source "mm/Kconfig" config LEDS bool "Timer and CPU usage LEDs" depends on ARCH_CDB89712 || ARCH_EBSA110 || \ - ARCH_EBSA285 || ARCH_IMX || ARCH_INTEGRATOR || \ + ARCH_EBSA285 || ARCH_INTEGRATOR || \ ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \ ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \ ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE || \ @@ -1137,7 +1177,7 @@ endmenu menu "CPU Power Management" -if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_IMX || ARCH_PXA) +if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA) source "drivers/cpufreq/Kconfig" @@ -1162,15 +1202,6 @@ config CPU_FREQ_INTEGRATOR If in doubt, say Y. -config CPU_FREQ_IMX - tristate "CPUfreq driver for i.MX CPUs" - depends on ARCH_IMX && CPU_FREQ - default n - help - This enables the CPUfreq driver for i.MX CPUs. - - If in doubt, say N. - config CPU_FREQ_PXA bool depends on CPU_FREQ && ARCH_PXA && PXA25x diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 885a83724b9..b6b9f6ee467 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -115,7 +115,6 @@ machine-$(CONFIG_ARCH_EBSA110) := ebsa110 machine-$(CONFIG_ARCH_EP93XX) := ep93xx machine-$(CONFIG_ARCH_GEMINI) := gemini machine-$(CONFIG_ARCH_H720X) := h720x -machine-$(CONFIG_ARCH_IMX) := imx machine-$(CONFIG_ARCH_INTEGRATOR) := integrator machine-$(CONFIG_ARCH_IOP13XX) := iop13xx machine-$(CONFIG_ARCH_IOP32X) := iop32x diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig new file mode 100644 index 00000000000..eb2738b5be5 --- /dev/null +++ b/arch/arm/configs/davinci_all_defconfig @@ -0,0 +1,1784 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.30-rc2 +# Wed Apr 15 08:16:53 2009 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +CONFIG_POSIX_MQUEUE_SYSCTL=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_CLASSIC_RCU=y +# CONFIG_TREE_RCU is not set +# CONFIG_PREEMPT_RCU is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_PREEMPT_RCU_TRACE is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +# CONFIG_CGROUPS is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_RD_GZIP=y +# CONFIG_RD_BZIP2 is not set +# CONFIG_RD_LZMA is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +# CONFIG_STRIP_ASM_SYMS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLUB_DEBUG=y +CONFIG_COMPAT_BRK=y +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y +# CONFIG_SLOW_WORK is not set +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MODVERSIONS=y +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +# CONFIG_FREEZER is not set + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_GEMINI is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +CONFIG_ARCH_DAVINCI=y +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_W90X900 is not set + +# +# TI DaVinci Implementations +# + +# +# DaVinci Core Type +# +CONFIG_ARCH_DAVINCI_DM644x=y + +# +# DaVinci Board Type +# +CONFIG_MACH_DAVINCI_EVM=y +CONFIG_DAVINCI_MUX=y +CONFIG_DAVINCI_MUX_DEBUG=y +CONFIG_DAVINCI_MUX_WARNINGS=y +CONFIG_DAVINCI_RESET_CLOCKS=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_PABRT_NOIFAR=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set +# CONFIG_OUTER_CACHE is not set +CONFIG_COMMON_CLKDEV=y + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PREEMPT=y +CONFIG_HZ=100 +CONFIG_AEABI=y +# CONFIG_OABI_COMPAT is not set +CONFIG_ARCH_FLATMEM_HAS_HOLES=y +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_LEDS=y +# CONFIG_LEDS_CPU is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Power Management +# +# CONFIG_CPU_IDLE is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +# CONFIG_PM is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +CONFIG_INET_TUNNEL=m +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +CONFIG_IPV6=m +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +# CONFIG_INET6_AH is not set +# CONFIG_INET6_ESP is not set +# CONFIG_INET6_IPCOMP is not set +# CONFIG_IPV6_MIP6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +CONFIG_INET6_XFRM_MODE_TRANSPORT=m +CONFIG_INET6_XFRM_MODE_TUNNEL=m +CONFIG_INET6_XFRM_MODE_BEET=m +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y +# CONFIG_IPV6_TUNNEL is not set +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set +# CONFIG_NETWORK_SECMARK is not set +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y + +# +# Core Netfilter Configuration +# +# CONFIG_NETFILTER_NETLINK_QUEUE is not set +# CONFIG_NETFILTER_NETLINK_LOG is not set +# CONFIG_NF_CONNTRACK is not set +# CONFIG_NETFILTER_XTABLES is not set +# CONFIG_IP_VS is not set + +# +# IP: Netfilter Configuration +# +# CONFIG_NF_DEFRAG_IPV4 is not set +# CONFIG_IP_NF_QUEUE is not set +# CONFIG_IP_NF_IPTABLES is not set +# CONFIG_IP_NF_ARPTABLES is not set + +# +# IPv6: Netfilter Configuration +# +# CONFIG_IP6_NF_QUEUE is not set +# CONFIG_IP6_NF_IPTABLES is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set +# CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +# CONFIG_WIRELESS is not set +# CONFIG_WIMAX is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=m +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_TESTS is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=m +CONFIG_MTD_BLKDEVS=m +CONFIG_MTD_BLOCK=m +# CONFIG_MTD_BLOCK_RO is not set +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=m +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=m +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=m +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=m +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_PHYSMAP=m +# CONFIG_MTD_PHYSMAP_COMPAT is not set +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=m +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_GPIO is not set +CONFIG_MTD_NAND_IDS=m +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ALAUDA is not set +CONFIG_MTD_NAND_DAVINCI=m +# CONFIG_MTD_ONENAND is not set + +# +# LPDDR flash memory drivers +# +# CONFIG_MTD_LPDDR is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=m +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=1 +CONFIG_BLK_DEV_RAM_SIZE=32768 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +CONFIG_EEPROM_AT24=y +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_93CX6 is not set +CONFIG_HAVE_IDE=y +CONFIG_IDE=m + +# +# Please see Documentation/ide/ide.txt for help/info on IDE drives +# +CONFIG_IDE_XFER_MODE=y +CONFIG_IDE_TIMINGS=y +# CONFIG_BLK_DEV_IDE_SATA is not set +CONFIG_IDE_GD=m +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set +# CONFIG_BLK_DEV_IDECD is not set +# CONFIG_BLK_DEV_IDETAPE is not set +# CONFIG_IDE_TASK_IOCTL is not set +CONFIG_IDE_PROC_FS=y + +# +# IDE chipset support/bugfixes +# +# CONFIG_BLK_DEV_PLATFORM is not set +CONFIG_BLK_DEV_IDEDMA_SFF=y +CONFIG_BLK_DEV_PALMCHIP_BK3710=m +CONFIG_BLK_DEV_IDEDMA=y + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=m +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=m +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_LIBFC is not set +# CONFIG_LIBFCOE is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +CONFIG_COMPAT_NET_DEV_OPS=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +CONFIG_TUN=m +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +CONFIG_LXT_PHY=y +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_NATIONAL_PHY is not set +# CONFIG_STE10XP is not set +CONFIG_LSI_ET1011C_PHY=y +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_ETHOC is not set +# CONFIG_SMC911X is not set +# CONFIG_SMSC911X is not set +# CONFIG_DNET is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +CONFIG_PPP=m +# CONFIG_PPP_MULTILINK is not set +# CONFIG_PPP_FILTER is not set +CONFIG_PPP_ASYNC=m +CONFIG_PPP_SYNC_TTY=m +CONFIG_PPP_DEFLATE=m +# CONFIG_PPP_BSDCOMP is not set +# CONFIG_PPP_MPPE is not set +# CONFIG_PPPOE is not set +# CONFIG_PPPOL2TP is not set +# CONFIG_SLIP is not set +CONFIG_SLHC=m +CONFIG_NETCONSOLE=y +# CONFIG_NETCONSOLE_DYNAMIC is not set +CONFIG_NETPOLL=y +CONFIG_NETPOLL_TRAP=y +CONFIG_NET_POLL_CONTROLLER=y +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=m +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=m +CONFIG_INPUT_EVBUG=m + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +CONFIG_KEYBOARD_ATKBD=m +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +CONFIG_KEYBOARD_XTKBD=m +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_KEYBOARD_GPIO=y +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_FUJITSU is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set +# CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_SERPORT=y +CONFIG_SERIO_LIBPS2=y +# CONFIG_SERIO_RAW is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +# CONFIG_VT_CONSOLE is not set +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=3 +CONFIG_SERIAL_8250_RUNTIME_UARTS=3 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=m +# CONFIG_HW_RANDOM_TIMERIOMEM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_DAVINCI=y +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +# CONFIG_GPIO_SYSFS is not set + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +CONFIG_GPIO_PCF857X=m + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7414 is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7462 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set +# CONFIG_SENSORS_ADT7475 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set +# CONFIG_SENSORS_G760A is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_LM93 is not set +# CONFIG_SENSORS_LTC4215 is not set +# CONFIG_SENSORS_LTC4245 is not set +# CONFIG_SENSORS_LM95241 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_SHT15 is not set +# CONFIG_SENSORS_DME1737 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_DAVINCI_WATCHDOG=m + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set +# CONFIG_TWL4030_CORE is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +CONFIG_VIDEO_DEV=y +CONFIG_VIDEO_V4L2_COMMON=y +CONFIG_VIDEO_ALLOW_V4L1=y +CONFIG_VIDEO_V4L1_COMPAT=y +# CONFIG_DVB_CORE is not set +CONFIG_VIDEO_MEDIA=y + +# +# Multimedia drivers +# +# CONFIG_MEDIA_ATTACH is not set +CONFIG_MEDIA_TUNER=y +# CONFIG_MEDIA_TUNER_CUSTOMISE is not set +CONFIG_MEDIA_TUNER_SIMPLE=y +CONFIG_MEDIA_TUNER_TDA8290=y +CONFIG_MEDIA_TUNER_TDA9887=y +CONFIG_MEDIA_TUNER_TEA5761=y +CONFIG_MEDIA_TUNER_TEA5767=y +CONFIG_MEDIA_TUNER_MT20XX=y +CONFIG_MEDIA_TUNER_XC2028=y +CONFIG_MEDIA_TUNER_XC5000=y +CONFIG_MEDIA_TUNER_MC44S803=y +CONFIG_VIDEO_V4L2=y +CONFIG_VIDEO_V4L1=y +CONFIG_VIDEO_CAPTURE_DRIVERS=y +# CONFIG_VIDEO_ADV_DEBUG is not set +# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set +CONFIG_VIDEO_HELPER_CHIPS_AUTO=y +# CONFIG_VIDEO_VIVI is not set +# CONFIG_VIDEO_CPIA is not set +# CONFIG_VIDEO_CPIA2 is not set +# CONFIG_VIDEO_SAA5246A is not set +# CONFIG_VIDEO_SAA5249 is not set +# CONFIG_SOC_CAMERA is not set +# CONFIG_V4L_USB_DRIVERS is not set +# CONFIG_RADIO_ADAPTERS is not set +CONFIG_DAB=y +# CONFIG_USB_DABUSB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +CONFIG_FB=y +CONFIG_FIRMWARE_EDID=y +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +# CONFIG_FB_CFB_FILLRECT is not set +# CONFIG_FB_CFB_COPYAREA is not set +# CONFIG_FB_CFB_IMAGEBLIT is not set +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +# CONFIG_FB_BROADSHEET is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +# CONFIG_FONTS is not set +CONFIG_FONT_8x8=y +CONFIG_FONT_8x16=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_MONO=y +CONFIG_LOGO_LINUX_VGA16=y +CONFIG_LOGO_LINUX_CLUT224=y +CONFIG_SOUND=m +# CONFIG_SOUND_OSS_CORE is not set +CONFIG_SND=m +CONFIG_SND_TIMER=m +CONFIG_SND_PCM=m +CONFIG_SND_JACK=y +# CONFIG_SND_SEQUENCER is not set +# CONFIG_SND_MIXER_OSS is not set +# CONFIG_SND_PCM_OSS is not set +# CONFIG_SND_HRTIMER is not set +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_ARM=y +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_CAIAQ is not set +CONFIG_SND_SOC=m +# CONFIG_SND_DAVINCI_SOC is not set +CONFIG_SND_SOC_I2C_AND_SPI=m +# CONFIG_SND_SOC_ALL_CODECS is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=m +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=m +# CONFIG_HID_PID is not set +# CONFIG_USB_HIDDEV is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set + +# +# Special HID drivers +# +CONFIG_HID_A4TECH=m +CONFIG_HID_APPLE=m +CONFIG_HID_BELKIN=m +CONFIG_HID_CHERRY=m +CONFIG_HID_CHICONY=m +CONFIG_HID_CYPRESS=m +# CONFIG_DRAGONRISE_FF is not set +CONFIG_HID_EZKEY=m +# CONFIG_HID_KYE is not set +CONFIG_HID_GYRATION=m +# CONFIG_HID_KENSINGTON is not set +CONFIG_HID_LOGITECH=m +# CONFIG_LOGITECH_FF is not set +# CONFIG_LOGIRUMBLEPAD2_FF is not set +CONFIG_HID_MICROSOFT=m +CONFIG_HID_MONTEREY=m +# CONFIG_HID_NTRIG is not set +CONFIG_HID_PANTHERLORD=m +# CONFIG_PANTHERLORD_FF is not set +CONFIG_HID_PETALYNX=m +CONFIG_HID_SAMSUNG=m +CONFIG_HID_SONY=m +CONFIG_HID_SUNPLUS=m +# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_TOPSEED is not set +# CONFIG_THRUSTMASTER_FF is not set +# CONFIG_ZEROPLUS_FF is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=m +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=m +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +CONFIG_USB_MUSB_HDRC=m +CONFIG_USB_MUSB_SOC=y + +# +# DaVinci 35x and 644x USB support +# +# CONFIG_USB_MUSB_HOST is not set +CONFIG_USB_MUSB_PERIPHERAL=y +# CONFIG_USB_MUSB_OTG is not set +CONFIG_USB_GADGET_MUSB_HDRC=y +CONFIG_MUSB_PIO_ONLY=y +# CONFIG_USB_MUSB_DEBUG is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=m +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +CONFIG_USB_TEST=m +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +CONFIG_USB_GADGET=m +# CONFIG_USB_GADGET_DEBUG is not set +CONFIG_USB_GADGET_DEBUG_FILES=y +CONFIG_USB_GADGET_DEBUG_FS=y +CONFIG_USB_GADGET_VBUS_DRAW=2 +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_PXA27X is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_FSL_QE is not set +# CONFIG_USB_GADGET_CI13XXX is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +CONFIG_USB_GADGET_DUALSPEED=y +CONFIG_USB_ZERO=m +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m +# CONFIG_USB_MIDI_GADGET is not set +CONFIG_USB_G_PRINTER=m +CONFIG_USB_CDC_COMPOSITE=m + +# +# OTG and related infrastructure +# +CONFIG_USB_OTG_UTILS=y +# CONFIG_USB_GPIO_VBUS is not set +# CONFIG_NOP_USB_XCEIV is not set +CONFIG_MMC=m +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=m +# CONFIG_MMC_BLOCK_BOUNCE is not set +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set +# CONFIG_MEMSTICK is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=m + +# +# LED drivers +# +# CONFIG_LEDS_PCA9532 is not set +CONFIG_LEDS_GPIO=m +CONFIG_LEDS_GPIO_PLATFORM=y +# CONFIG_LEDS_LP5521 is not set +# CONFIG_LEDS_PCA955X is not set +# CONFIG_LEDS_BD2802 is not set + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=m +# CONFIG_LEDS_TRIGGER_IDE_DISK is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=m +# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set +# CONFIG_LEDS_TRIGGER_GPIO is not set +# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set + +# +# iptables trigger is under Netfilter config (LED target) +# +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=m + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_DMADEVICES is not set +# CONFIG_AUXDISPLAY is not set +# CONFIG_REGULATOR is not set +# CONFIG_UIO is not set +# CONFIG_STAGING is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4_FS is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y +CONFIG_XFS_FS=m +# CONFIG_XFS_QUOTA is not set +# CONFIG_XFS_POSIX_ACL is not set +# CONFIG_XFS_RT is not set +# CONFIG_XFS_DEBUG is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +CONFIG_AUTOFS4_FS=m +# CONFIG_FUSE_FS is not set + +# +# Caches +# +# CONFIG_FSCACHE is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set +CONFIG_MISC_FILESYSTEMS=y +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=m +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_SQUASHFS is not set +# CONFIG_VXFS_FS is not set +CONFIG_MINIX_FS=m +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +CONFIG_ROOT_NFS=y +CONFIG_NFSD=m +CONFIG_NFSD_V3=y +# CONFIG_NFSD_V3_ACL is not set +# CONFIG_NFSD_V4 is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=m +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +CONFIG_SMB_FS=m +# CONFIG_SMB_NLS_DEFAULT is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +CONFIG_NLS_ASCII=m +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_DETECT_HUNG_TASK=y +# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set +CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +CONFIG_TIMER_STATS=y +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set +CONFIG_DEBUG_PREEMPT=y +CONFIG_DEBUG_RT_MUTEXES=y +CONFIG_DEBUG_PI_LIST=y +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +# CONFIG_SYSCTL_SYSCALL_CHECK is not set +# CONFIG_PAGE_POISONING is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_TRACING_SUPPORT=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_PREEMPT_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_EVENT_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_TRACE_BRANCH_PROFILING is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_KMEMTRACE is not set +# CONFIG_WORKQUEUE_TRACER is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_DYNAMIC_DEBUG is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +CONFIG_ARM_UNWIND=y +CONFIG_DEBUG_USER=y +CONFIG_DEBUG_ERRORS=y +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_LL is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_FIPS is not set +# CONFIG_CRYPTO_MANAGER is not set +# CONFIG_CRYPTO_MANAGER2 is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_ZLIB is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +# CONFIG_CRYPTO_HW is not set +# CONFIG_BINARY_PRINTF is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_CRC_CCITT=m +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=m +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=m +CONFIG_DECOMPRESS_GZIP=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_NLATTR=y diff --git a/arch/arm/configs/mx31moboard_defconfig b/arch/arm/configs/mx21_defconfig index e90f86d6dee..4b04290d8e8 100644 --- a/arch/arm/configs/mx31moboard_defconfig +++ b/arch/arm/configs/mx21_defconfig @@ -1,9 +1,10 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc5 -# Fri Oct 24 11:41:22 2008 +# Linux kernel version: 2.6.30-rc1 +# Tue Apr 14 16:58:09 2009 # CONFIG_ARM=y +CONFIG_HAVE_PWM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y CONFIG_GENERIC_TIME=y @@ -22,8 +23,6 @@ CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_ARCH_SUPPORTS_AOUT=y -CONFIG_ZONE_DMA=y CONFIG_ARCH_MTD_XIP=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_VECTORS_BASE=0xffff0000 @@ -38,48 +37,53 @@ CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 CONFIG_LOCALVERSION="" CONFIG_LOCALVERSION_AUTO=y -CONFIG_SWAP=y +# CONFIG_SWAP is not set CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_AUDIT is not set -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y + +# +# RCU Subsystem +# +CONFIG_CLASSIC_RCU=y +# CONFIG_TREE_RCU is not set +# CONFIG_PREEMPT_RCU is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_PREEMPT_RCU_TRACE is not set +# CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_GROUP_SCHED is not set # CONFIG_CGROUPS is not set -CONFIG_GROUP_SCHED=y -CONFIG_FAIR_GROUP_SCHED=y -# CONFIG_RT_GROUP_SCHED is not set -CONFIG_USER_SCHED=y -# CONFIG_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set # CONFIG_NAMESPACES is not set # CONFIG_BLK_DEV_INITRD is not set -CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_KALLSYMS_EXTRA_PASS=y CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y -CONFIG_COMPAT_BRK=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y -CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set @@ -87,31 +91,21 @@ CONFIG_SLAB=y # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y # CONFIG_KPROBES is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_SLOW_WORK is not set CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y -# CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y # CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y -CONFIG_MODULE_FORCE_UNLOAD=y -CONFIG_MODVERSIONS=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y CONFIG_BLOCK=y # CONFIG_LBD is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -119,15 +113,15 @@ CONFIG_BLOCK=y # IO Schedulers # CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y +# CONFIG_IOSCHED_AS is not set +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set # CONFIG_DEFAULT_AS is not set # CONFIG_DEFAULT_DEADLINE is not set -CONFIG_DEFAULT_CFQ=y -# CONFIG_DEFAULT_NOOP is not set -CONFIG_DEFAULT_IOSCHED="cfq" -CONFIG_CLASSIC_RCU=y +# CONFIG_DEFAULT_CFQ is not set +CONFIG_DEFAULT_NOOP=y +CONFIG_DEFAULT_IOSCHED="noop" +# CONFIG_FREEZER is not set # # System Type @@ -137,14 +131,13 @@ CONFIG_CLASSIC_RCU=y # CONFIG_ARCH_REALVIEW is not set # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_AT91 is not set -# CONFIG_ARCH_CLPS7500 is not set # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_IMX is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set @@ -161,52 +154,45 @@ CONFIG_ARCH_MXC=y # CONFIG_ARCH_ORION5X is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_MMP is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_S3C64XX is not set # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_MSM7X00A is not set - -# -# Boot options -# - -# -# Power management -# +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_W90X900 is not set # # Freescale MXC Implementations # -# CONFIG_ARCH_MX2 is not set -CONFIG_ARCH_MX3=y +# CONFIG_ARCH_MX1 is not set +CONFIG_ARCH_MX2=y +# CONFIG_ARCH_MX3 is not set +CONFIG_MACH_MX21=y +# CONFIG_MACH_MX27 is not set # -# MX3 Options +# MX2 platforms: # -# CONFIG_MACH_MX31ADS is not set -# CONFIG_MACH_PCM037 is not set -# CONFIG_MACH_MX31LITE is not set -CONFIG_MACH_MX31MOBOARD=y +CONFIG_MACH_MX21ADS=y # CONFIG_MXC_IRQ_PRIOR is not set +CONFIG_MXC_PWM=y # # Processor Type # CONFIG_CPU_32=y -CONFIG_CPU_V6=y -# CONFIG_CPU_32v6K is not set -CONFIG_CPU_32v6=y -CONFIG_CPU_ABRT_EV6=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y CONFIG_CPU_PABRT_NOIFAR=y -CONFIG_CPU_CACHE_V6=y -CONFIG_CPU_CACHE_VIPT=y -CONFIG_CPU_COPY_V6=y -CONFIG_CPU_TLB_V6=y -CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y CONFIG_CPU_CP15=y CONFIG_CPU_CP15_MMU=y @@ -216,8 +202,10 @@ CONFIG_CPU_CP15_MMU=y CONFIG_ARM_THUMB=y # CONFIG_CPU_ICACHE_DISABLE is not set # CONFIG_CPU_DCACHE_DISABLE is not set -# CONFIG_CPU_BPREDICT_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set # CONFIG_OUTER_CACHE is not set +CONFIG_COMMON_CLKDEV=y # # Bus support @@ -233,26 +221,32 @@ CONFIG_TICK_ONESHOT=y CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 CONFIG_PREEMPT=y CONFIG_HZ=100 CONFIG_AEABI=y -# CONFIG_OABI_COMPAT is not set +CONFIG_OABI_COMPAT=y CONFIG_ARCH_FLATMEM_HAS_HOLES=y -# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_SPLIT_PTLOCK_CPUS=4 -# CONFIG_RESOURCES_64BIT is not set -CONFIG_ZONE_DMA_FLAG=1 -CONFIG_BOUNCE=y +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y CONFIG_ALIGNMENT_TRAP=y # @@ -260,23 +254,32 @@ CONFIG_ALIGNMENT_TRAP=y # CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="noinitrd console=ttymxc0,115200 root=/dev/mtdblock2 rw ip=off" +CONFIG_CMDLINE="" # CONFIG_XIP_KERNEL is not set # CONFIG_KEXEC is not set # +# CPU Power Management +# +# CONFIG_CPU_IDLE is not set + +# # Floating point emulation # # # At least one emulation must be selected # -CONFIG_VFP=y +# CONFIG_FPE_NWFPE is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set # # Userspace binary formats # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y # CONFIG_BINFMT_AOUT is not set # CONFIG_BINFMT_MISC is not set @@ -290,9 +293,13 @@ CONFIG_NET=y # # Networking options # -CONFIG_PACKET=y -# CONFIG_PACKET_MMAP is not set -CONFIG_UNIX=y +# CONFIG_PACKET is not set +# CONFIG_UNIX is not set +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set # CONFIG_NET_KEY is not set CONFIG_INET=y # CONFIG_IP_MULTICAST is not set @@ -300,7 +307,7 @@ CONFIG_INET=y CONFIG_IP_FIB_HASH=y CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y -# CONFIG_IP_PNP_BOOTP is not set +CONFIG_IP_PNP_BOOTP=y # CONFIG_IP_PNP_RARP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set @@ -311,7 +318,7 @@ CONFIG_IP_PNP_DHCP=y # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set # CONFIG_INET_LRO is not set @@ -328,6 +335,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -337,7 +345,9 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set # CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set # # Network testing @@ -348,14 +358,13 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# +CONFIG_WIRELESS=y # CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_OLD_REGULATORY is not set # CONFIG_WIRELESS_EXT is not set +# CONFIG_LIB80211 is not set # CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +# CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -369,20 +378,20 @@ CONFIG_DEFAULT_TCP_CONG="cubic" CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y -CONFIG_FW_LOADER=m -CONFIG_FIRMWARE_IN_KERNEL=y -CONFIG_EXTRA_FIRMWARE="" +# CONFIG_FW_LOADER is not set # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set CONFIG_MTD=y -# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_DEBUG=y +CONFIG_MTD_DEBUG_VERBOSE=3 # CONFIG_MTD_CONCAT is not set CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_TESTS is not set CONFIG_MTD_REDBOOT_PARTS=y CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1 # CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set -CONFIG_MTD_REDBOOT_PARTS_READONLY=y -# CONFIG_MTD_CMDLINE_PARTS is not set +# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set +CONFIG_MTD_CMDLINE_PARTS=y # CONFIG_MTD_AFS_PARTS is not set # CONFIG_MTD_AR7_PARTS is not set @@ -412,12 +421,12 @@ CONFIG_MTD_CFI_NOSWAP=y CONFIG_MTD_CFI_GEOMETRY=y # CONFIG_MTD_MAP_BANK_WIDTH_1 is not set CONFIG_MTD_MAP_BANK_WIDTH_2=y -# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set CONFIG_MTD_CFI_I1=y -# CONFIG_MTD_CFI_I2 is not set +CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_OTP is not set @@ -435,15 +444,15 @@ CONFIG_MTD_CFI_UTIL=y # # CONFIG_MTD_COMPLEX_MAPPINGS is not set CONFIG_MTD_PHYSMAP=y -CONFIG_MTD_PHYSMAP_START=0x0 -CONFIG_MTD_PHYSMAP_LEN=0x0 -CONFIG_MTD_PHYSMAP_BANKWIDTH=2 +# CONFIG_MTD_PHYSMAP_COMPAT is not set # CONFIG_MTD_ARM_INTEGRATOR is not set # CONFIG_MTD_PLATRAM is not set # # Self-contained MTD device drivers # +# CONFIG_MTD_DATAFLASH is not set +# CONFIG_MTD_M25P80 is not set # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set @@ -455,16 +464,48 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2 # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_GPIO is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +CONFIG_MTD_NAND_MXC=y # CONFIG_MTD_ONENAND is not set # +# LPDDR flash memory drivers +# +# CONFIG_MTD_LPDDR is not set + +# # UBI - Unsorted block images # # CONFIG_MTD_UBI is not set # CONFIG_PARPORT is not set -# CONFIG_BLK_DEV is not set -# CONFIG_MISC_DEVICES is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +# CONFIG_EEPROM_AT24 is not set +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_93CX6 is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -478,6 +519,7 @@ CONFIG_HAVE_IDE=y # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y +CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -488,13 +530,23 @@ CONFIG_NETDEVICES=y CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_AX88796 is not set -CONFIG_SMC91X=y +# CONFIG_SMC91X is not set # CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_ETHOC is not set +# CONFIG_SMC911X is not set +# CONFIG_SMSC911X is not set +# CONFIG_DNET is not set # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +CONFIG_CS89x0=y +CONFIG_CS89x0_NONISA_IRQ=y # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -503,7 +555,10 @@ CONFIG_SMC91X=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI_LEDS is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# # CONFIG_WAN is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set @@ -515,7 +570,40 @@ CONFIG_SMC91X=y # # Input device support # -# CONFIG_INPUT is not set +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +# CONFIG_TOUCHSCREEN_ADS7846 is not set +# CONFIG_TOUCHSCREEN_FUJITSU is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set +# CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_INPUT_MISC is not set # # Hardware I/O ports @@ -526,39 +614,109 @@ CONFIG_SMC91X=y # # Character devices # -# CONFIG_VT is not set +CONFIG_VT=y +# CONFIG_CONSOLE_TRANSLATIONS is not set +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # # Serial drivers # -# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=1 +CONFIG_SERIAL_8250_RUNTIME_UARTS=1 +# CONFIG_SERIAL_8250_EXTENDED is not set # # Non-8250 serial port support # +# CONFIG_SERIAL_MAX3100 is not set CONFIG_SERIAL_IMX=y CONFIG_SERIAL_IMX_CONSOLE=y CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set # CONFIG_LEGACY_PTYS is not set # CONFIG_IPMI_HANDLER is not set # CONFIG_HW_RANDOM is not set -# CONFIG_NVRAM is not set # CONFIG_R3964 is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set -# CONFIG_I2C is not set -# CONFIG_SPI is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_GPIO is not set +CONFIG_I2C_IMX=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set +# CONFIG_SPI_GPIO is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y # CONFIG_GPIO_SYSFS is not set # +# Memory mapped GPIO expanders: +# + +# # I2C GPIO expanders: # +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set # # PCI GPIO expanders: @@ -567,15 +725,19 @@ CONFIG_GPIOLIB=y # # SPI GPIO expanders: # +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -583,12 +745,17 @@ CONFIG_SSB_POSSIBLE=y # # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set # CONFIG_HTC_EGPIO is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set +# CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set -# CONFIG_MFD_T7L66XB is not set -# CONFIG_MFD_TC6387XB is not set # CONFIG_MFD_TC6393XB is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set # # Multimedia devices @@ -611,50 +778,122 @@ CONFIG_SSB_POSSIBLE=y # # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +CONFIG_FB_IMX=y +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +# CONFIG_FB_BROADSHEET is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +CONFIG_FONTS=y +CONFIG_FONT_8x8=y +# CONFIG_FONT_8x16 is not set +# CONFIG_FONT_6x11 is not set +# CONFIG_FONT_7x14 is not set +# CONFIG_FONT_PEARL_8x8 is not set +# CONFIG_FONT_ACORN_8x8 is not set +# CONFIG_FONT_MINI_4x6 is not set +# CONFIG_FONT_SUN8x16 is not set +# CONFIG_FONT_SUN12x22 is not set +# CONFIG_FONT_10x18 is not set +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_MONO=y +CONFIG_LOGO_LINUX_VGA16=y +CONFIG_LOGO_LINUX_CLUT224=y # CONFIG_SOUND is not set +# CONFIG_HID_SUPPORT is not set # CONFIG_USB_SUPPORT is not set -# CONFIG_MMC is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set +CONFIG_MMC_MXC=y +# CONFIG_MMC_SPI is not set +# CONFIG_MEMSTICK is not set +# CONFIG_ACCESSIBILITY is not set # CONFIG_NEW_LEDS is not set CONFIG_RTC_LIB=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set - -# -# Voltage and Current regulators -# +# CONFIG_AUXDISPLAY is not set # CONFIG_REGULATOR is not set -# CONFIG_REGULATOR_FIXED_VOLTAGE is not set -# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set -# CONFIG_REGULATOR_BQ24022 is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set # # File systems # # CONFIG_EXT2_FS is not set # CONFIG_EXT3_FS is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set # CONFIG_DNOTIFY is not set -CONFIG_INOTIFY=y -CONFIG_INOTIFY_USER=y +# CONFIG_INOTIFY is not set # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set # +# Caches +# +# CONFIG_FSCACHE is not set + +# # CD-ROM/DVD Filesystems # # CONFIG_ISO9660_FS is not set @@ -663,8 +902,10 @@ CONFIG_INOTIFY_USER=y # # DOS/FAT/NT Filesystems # -# CONFIG_MSDOS_FS is not set +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y # CONFIG_VFAT_FS is not set +CONFIG_FAT_DEFAULT_CODEPAGE=437 # CONFIG_NTFS_FS is not set # @@ -672,15 +913,13 @@ CONFIG_INOTIFY_USER=y # CONFIG_PROC_FS=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set # CONFIG_CONFIGFS_FS is not set - -# -# Miscellaneous filesystems -# +CONFIG_MISC_FILESYSTEMS=y # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_HFS_FS is not set @@ -700,6 +939,7 @@ CONFIG_JFFS2_ZLIB=y CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set # CONFIG_CRAMFS is not set +# CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_OMFS_FS is not set @@ -708,13 +948,16 @@ CONFIG_JFFS2_RTIME=y # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set +# CONFIG_NILFS2_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y -# CONFIG_NFS_V3 is not set +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y # CONFIG_RPCSEC_GSS_KRB5 is not set @@ -730,15 +973,54 @@ CONFIG_SUNRPC=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set -# CONFIG_ENABLE_WARN_DEPRECATED is not set -# CONFIG_ENABLE_MUST_CHECK is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -747,18 +1029,30 @@ CONFIG_FRAME_WARN=1024 # CONFIG_DEBUG_KERNEL is not set # CONFIG_DEBUG_BUGVERBOSE is not set # CONFIG_DEBUG_MEMORY_INIT is not set -CONFIG_FRAME_POINTER=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_LATENCYTOP is not set CONFIG_SYSCTL_SYSCALL_CHECK=y -CONFIG_HAVE_FTRACE=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -# CONFIG_FTRACE is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_TRACING_SUPPORT=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set # CONFIG_IRQSOFF_TRACER is not set # CONFIG_PREEMPT_TRACER is not set # CONFIG_SCHED_TRACER is not set # CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_EVENT_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_TRACE_BRANCH_PROFILING is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_KMEMTRACE is not set +# CONFIG_WORKQUEUE_TRACER is not set +# CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +CONFIG_ARM_UNWIND=y # CONFIG_DEBUG_USER is not set # @@ -766,15 +1060,101 @@ CONFIG_HAVE_ARCH_KGDB=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set -# CONFIG_CRYPTO is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_FIPS is not set +# CONFIG_CRYPTO_MANAGER is not set +# CONFIG_CRYPTO_MANAGER2 is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_ZLIB is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y +# CONFIG_BINARY_PRINTF is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set +CONFIG_GENERIC_FIND_LAST_BIT=y # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set # CONFIG_CRC_T10DIF is not set @@ -784,7 +1164,7 @@ CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y -CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y +CONFIG_NLATTR=y diff --git a/arch/arm/configs/mx3_defconfig b/arch/arm/configs/mx3_defconfig index 72a8201a537..20ada526f6d 100644 --- a/arch/arm/configs/mx3_defconfig +++ b/arch/arm/configs/mx3_defconfig @@ -197,7 +197,7 @@ CONFIG_MXC_PWM=y # CONFIG_CPU_32=y CONFIG_CPU_V6=y -CONFIG_CPU_32v6K=y +# CONFIG_CPU_32v6K is not set CONFIG_CPU_32v6=y CONFIG_CPU_ABRT_EV6=y CONFIG_CPU_PABRT_NOIFAR=y diff --git a/arch/arm/configs/viper_defconfig b/arch/arm/configs/viper_defconfig index 30f463d2fa8..6ab5dd5868d 100644 --- a/arch/arm/configs/viper_defconfig +++ b/arch/arm/configs/viper_defconfig @@ -298,7 +298,6 @@ CONFIG_CPU_FREQ_GOV_POWERSAVE=m CONFIG_CPU_FREQ_GOV_USERSPACE=m CONFIG_CPU_FREQ_GOV_ONDEMAND=m CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m -CONFIG_CPU_FREQ_PXA=y # # Floating point emulation diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index bac988e7a4c..a9c78bc72b8 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -4,19 +4,56 @@ menu "TI DaVinci Implementations" comment "DaVinci Core Type" -config ARCH_DAVINCI644x - default y +config ARCH_DAVINCI_DM644x bool "DaVinci 644x based system" comment "DaVinci Board Type" config MACH_DAVINCI_EVM - bool "TI DaVinci EVM" + bool "TI DM644x EVM" default y - depends on ARCH_DAVINCI644x + depends on ARCH_DAVINCI_DM644x help Configure this option to specify the whether the board used - for development is a DaVinci EVM + for development is a DM644x EVM + + +config DAVINCI_MUX + bool "DAVINCI multiplexing support" + depends on ARCH_DAVINCI + default y + help + Pin multiplexing support for DAVINCI boards. If your bootloader + sets the multiplexing correctly, say N. Otherwise, or if unsure, + say Y. + +config DAVINCI_MUX_DEBUG + bool "Multiplexing debug output" + depends on DAVINCI_MUX + help + Makes the multiplexing functions print out a lot of debug info. + This is useful if you want to find out the correct values of the + multiplexing registers. + +config DAVINCI_MUX_WARNINGS + bool "Warn about pins the bootloader didn't set up" + depends on DAVINCI_MUX + help + Choose Y here to warn whenever driver initialization logic needs + to change the pin multiplexing setup. When there are no warnings + printed, it's safe to deselect DAVINCI_MUX for your product. + +config DAVINCI_RESET_CLOCKS + bool "Reset unused clocks during boot" + depends on ARCH_DAVINCI + help + Say Y if you want to reset unused clocks during boot. + This option saves power, but assumes all drivers are + using the clock framework. Broken drivers that do not + yet use clock framework may not work with this option. + If you are booting from another operating system, you + probably do not want this option enabled until your + device drivers work properly. endmenu diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index 4dc458597f4..1674661942f 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -5,7 +5,12 @@ # Common objects obj-y := time.o irq.o clock.o serial.o io.o id.o psc.o \ - gpio.o mux.o devices.o usb.o + gpio.o devices.o dma.o usb.o + +obj-$(CONFIG_DAVINCI_MUX) += mux.o + +# Chip specific +obj-$(CONFIG_ARCH_DAVINCI_DM644x) += dm644x.o # Board specific -obj-$(CONFIG_MACH_DAVINCI_EVM) += board-evm.o +obj-$(CONFIG_MACH_DAVINCI_EVM) += board-dm644x-evm.o diff --git a/arch/arm/mach-davinci/board-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index 0b97a528902..c039674fe99 100644 --- a/arch/arm/mach-davinci/board-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -15,15 +15,20 @@ #include <linux/platform_device.h> #include <linux/gpio.h> #include <linux/leds.h> +#include <linux/memory.h> +#include <linux/etherdevice.h> #include <linux/i2c.h> #include <linux/i2c/pcf857x.h> #include <linux/i2c/at24.h> #include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> #include <linux/mtd/partitions.h> #include <linux/mtd/physmap.h> #include <linux/io.h> +#include <linux/phy.h> +#include <linux/clk.h> #include <asm/setup.h> #include <asm/mach-types.h> @@ -32,25 +37,34 @@ #include <asm/mach/map.h> #include <asm/mach/flash.h> -#include <mach/hardware.h> +#include <mach/dm644x.h> #include <mach/common.h> #include <mach/i2c.h> +#include <mach/serial.h> +#include <mach/mux.h> +#include <mach/psc.h> +#include <mach/nand.h> -/* other misc. init functions */ -void __init davinci_psc_init(void); -void __init davinci_irq_init(void); -void __init davinci_map_common_io(void); -void __init davinci_init_common_hw(void); +#define DM644X_EVM_PHY_MASK (0x2) +#define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ -#if defined(CONFIG_MTD_PHYSMAP) || \ - defined(CONFIG_MTD_PHYSMAP_MODULE) +#define DAVINCI_CFC_ATA_BASE 0x01C66000 + +#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e00000 +#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000 +#define DAVINCI_ASYNC_EMIF_DATA_CE1_BASE 0x04000000 +#define DAVINCI_ASYNC_EMIF_DATA_CE2_BASE 0x06000000 +#define DAVINCI_ASYNC_EMIF_DATA_CE3_BASE 0x08000000 + +#define LXT971_PHY_ID (0x001378e2) +#define LXT971_PHY_MASK (0xfffffff0) static struct mtd_partition davinci_evm_norflash_partitions[] = { - /* bootloader (U-Boot, etc) in first 4 sectors */ + /* bootloader (UBL, U-Boot, etc) in first 5 sectors */ { .name = "bootloader", .offset = 0, - .size = 4 * SZ_64K, + .size = 5 * SZ_64K, .mask_flags = MTD_WRITEABLE, /* force read-only */ }, /* bootloader params in the next 1 sectors */ @@ -100,10 +114,89 @@ static struct platform_device davinci_evm_norflash_device = { .resource = &davinci_evm_norflash_resource, }; -#endif +/* DM644x EVM includes a 64 MByte small-page NAND flash (16K blocks). + * It may used instead of the (default) NOR chip to boot, using TI's + * tools to install the secondary boot loader (UBL) and U-Boot. + */ +struct mtd_partition davinci_evm_nandflash_partition[] = { + /* Bootloader layout depends on whose u-boot is installed, but we + * can hide all the details. + * - block 0 for u-boot environment ... in mainline u-boot + * - block 1 for UBL (plus up to four backup copies in blocks 2..5) + * - blocks 6...? for u-boot + * - blocks 16..23 for u-boot environment ... in TI's u-boot + */ + { + .name = "bootloader", + .offset = 0, + .size = SZ_256K + SZ_128K, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + /* Kernel */ + { + .name = "kernel", + .offset = MTDPART_OFS_APPEND, + .size = SZ_4M, + .mask_flags = 0, + }, + /* File system (older GIT kernels started this on the 5MB mark) */ + { + .name = "filesystem", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + .mask_flags = 0, + } + /* A few blocks at end hold a flash BBT ... created by TI's CCS + * using flashwriter_nand.out, but ignored by TI's versions of + * Linux and u-boot. We boot faster by using them. + */ +}; -#if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \ - defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE) +static struct davinci_nand_pdata davinci_evm_nandflash_data = { + .parts = davinci_evm_nandflash_partition, + .nr_parts = ARRAY_SIZE(davinci_evm_nandflash_partition), + .ecc_mode = NAND_ECC_HW, + .options = NAND_USE_FLASH_BBT, +}; + +static struct resource davinci_evm_nandflash_resource[] = { + { + .start = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE, + .end = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1, + .flags = IORESOURCE_MEM, + }, { + .start = DAVINCI_ASYNC_EMIF_CONTROL_BASE, + .end = DAVINCI_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device davinci_evm_nandflash_device = { + .name = "davinci_nand", + .id = 0, + .dev = { + .platform_data = &davinci_evm_nandflash_data, + }, + .num_resources = ARRAY_SIZE(davinci_evm_nandflash_resource), + .resource = davinci_evm_nandflash_resource, +}; + +static u64 davinci_fb_dma_mask = DMA_BIT_MASK(32); + +static struct platform_device davinci_fb_device = { + .name = "davincifb", + .id = -1, + .dev = { + .dma_mask = &davinci_fb_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, + .num_resources = 0, +}; + +static struct platform_device rtc_dev = { + .name = "rtc_davinci_evm", + .id = -1, +}; static struct resource ide_resources[] = { { @@ -118,7 +211,7 @@ static struct resource ide_resources[] = { }, }; -static u64 ide_dma_mask = DMA_BIT_MASK(32); +static u64 ide_dma_mask = DMA_32BIT_MASK; static struct platform_device ide_dev = { .name = "palm_bk3710", @@ -127,12 +220,10 @@ static struct platform_device ide_dev = { .num_resources = ARRAY_SIZE(ide_resources), .dev = { .dma_mask = &ide_dma_mask, - .coherent_dma_mask = DMA_BIT_MASK(32), + .coherent_dma_mask = DMA_32BIT_MASK, }, }; -#endif - /*----------------------------------------------------------------------*/ /* @@ -311,7 +402,9 @@ evm_u35_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c) gpio_request(gpio + 7, "nCF_SEL"); gpio_direction_output(gpio + 7, 1); - /* irlml6401 sustains over 3A, switches 5V in under 8 msec */ + /* irlml6401 switches over 1A, in under 8 msec; + * now it can be managed by nDRV_VBUS ... + */ setup_usb(500, 8); return 0; @@ -343,14 +436,120 @@ static struct pcf857x_platform_data pcf_data_u35 = { * - 0x0039, 1 byte NTSC vs PAL (bit 0x80 == PAL) * - ... newer boards may have more */ +static struct memory_accessor *at24_mem_acc; + +static void at24_setup(struct memory_accessor *mem_acc, void *context) +{ + DECLARE_MAC_BUF(mac_str); + char mac_addr[6]; + + at24_mem_acc = mem_acc; + + /* Read MAC addr from EEPROM */ + if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x7f00, 6) == 6) { + printk(KERN_INFO "Read MAC addr from EEPROM: %s\n", + print_mac(mac_str, mac_addr)); + } +} + static struct at24_platform_data eeprom_info = { .byte_len = (256*1024) / 8, .page_size = 64, .flags = AT24_FLAG_ADDR16, + .setup = at24_setup, }; +int dm6446evm_eeprom_read(void *buf, off_t off, size_t count) +{ + if (at24_mem_acc) + return at24_mem_acc->read(at24_mem_acc, buf, off, count); + return -ENODEV; +} +EXPORT_SYMBOL(dm6446evm_eeprom_read); + +int dm6446evm_eeprom_write(void *buf, off_t off, size_t count) +{ + if (at24_mem_acc) + return at24_mem_acc->write(at24_mem_acc, buf, off, count); + return -ENODEV; +} +EXPORT_SYMBOL(dm6446evm_eeprom_write); + +/* + * MSP430 supports RTC, card detection, input from IR remote, and + * a bit more. It triggers interrupts on GPIO(7) from pressing + * buttons on the IR remote, and for card detect switches. + */ +static struct i2c_client *dm6446evm_msp; + +static int dm6446evm_msp_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + dm6446evm_msp = client; + return 0; +} + +static int dm6446evm_msp_remove(struct i2c_client *client) +{ + dm6446evm_msp = NULL; + return 0; +} + +static const struct i2c_device_id dm6446evm_msp_ids[] = { + { "dm6446evm_msp", 0, }, + { /* end of list */ }, +}; + +static struct i2c_driver dm6446evm_msp_driver = { + .driver.name = "dm6446evm_msp", + .id_table = dm6446evm_msp_ids, + .probe = dm6446evm_msp_probe, + .remove = dm6446evm_msp_remove, +}; + +static int dm6444evm_msp430_get_pins(void) +{ + static const char txbuf[2] = { 2, 4, }; + char buf[4]; + struct i2c_msg msg[2] = { + { + .addr = dm6446evm_msp->addr, + .flags = 0, + .len = 2, + .buf = (void __force *)txbuf, + }, + { + .addr = dm6446evm_msp->addr, + .flags = I2C_M_RD, + .len = 4, + .buf = buf, + }, + }; + int status; + + if (!dm6446evm_msp) + return -ENXIO; + + /* Command 4 == get input state, returns port 2 and port3 data + * S Addr W [A] len=2 [A] cmd=4 [A] + * RS Addr R [A] [len=4] A [cmd=4] A [port2] A [port3] N P + */ + status = i2c_transfer(dm6446evm_msp->adapter, msg, 2); + if (status < 0) + return status; + + dev_dbg(&dm6446evm_msp->dev, + "PINS: %02x %02x %02x %02x\n", + buf[0], buf[1], buf[2], buf[3]); + + return (buf[3] << 8) | buf[2]; +} + static struct i2c_board_info __initdata i2c_info[] = { { + I2C_BOARD_INFO("dm6446evm_msp", 0x23), + }, + { I2C_BOARD_INFO("pcf8574", 0x38), .platform_data = &pcf_data_u2, }, @@ -368,7 +567,6 @@ static struct i2c_board_info __initdata i2c_info[] = { }, /* ALSO: * - tvl320aic33 audio codec (0x1b) - * - msp430 microcontroller (0x23) * - tvp5146 video decoder (0x5d) */ }; @@ -384,51 +582,109 @@ static struct davinci_i2c_platform_data i2c_pdata = { static void __init evm_init_i2c(void) { davinci_init_i2c(&i2c_pdata); + i2c_add_driver(&dm6446evm_msp_driver); i2c_register_board_info(1, i2c_info, ARRAY_SIZE(i2c_info)); } static struct platform_device *davinci_evm_devices[] __initdata = { -#if defined(CONFIG_MTD_PHYSMAP) || \ - defined(CONFIG_MTD_PHYSMAP_MODULE) - &davinci_evm_norflash_device, -#endif -#if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \ - defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE) - &ide_dev, -#endif + &davinci_fb_device, + &rtc_dev, +}; + +static struct davinci_uart_config uart_config __initdata = { + .enabled_uarts = (1 << 0), }; static void __init davinci_evm_map_io(void) { davinci_map_common_io(); + dm644x_init(); } -static __init void davinci_evm_init(void) +static int davinci_phy_fixup(struct phy_device *phydev) { - davinci_psc_init(); + unsigned int control; + /* CRITICAL: Fix for increasing PHY signal drive strength for + * TX lockup issue. On DaVinci EVM, the Intel LXT971 PHY + * signal strength was low causing TX to fail randomly. The + * fix is to Set bit 11 (Increased MII drive strength) of PHY + * register 26 (Digital Config register) on this phy. */ + control = phy_read(phydev, 26); + phy_write(phydev, 26, (control | 0x800)); + return 0; +} #if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \ defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE) +#define HAS_ATA 1 +#else +#define HAS_ATA 0 +#endif + #if defined(CONFIG_MTD_PHYSMAP) || \ defined(CONFIG_MTD_PHYSMAP_MODULE) - printk(KERN_WARNING "WARNING: both IDE and NOR flash are enabled, " - "but share pins.\n\t Disable IDE for NOR support.\n"); +#define HAS_NOR 1 +#else +#define HAS_NOR 0 #endif + +#if defined(CONFIG_MTD_NAND_DAVINCI) || \ + defined(CONFIG_MTD_NAND_DAVINCI_MODULE) +#define HAS_NAND 1 +#else +#define HAS_NAND 0 #endif +static __init void davinci_evm_init(void) +{ + struct clk *aemif_clk; + + aemif_clk = clk_get(NULL, "aemif"); + clk_enable(aemif_clk); + + if (HAS_ATA) { + if (HAS_NAND || HAS_NOR) + pr_warning("WARNING: both IDE and Flash are " + "enabled, but they share AEMIF pins.\n" + "\tDisable IDE for NAND/NOR support.\n"); + davinci_cfg_reg(DM644X_HPIEN_DISABLE); + davinci_cfg_reg(DM644X_ATAEN); + davinci_cfg_reg(DM644X_HDIREN); + platform_device_register(&ide_dev); + } else if (HAS_NAND || HAS_NOR) { + davinci_cfg_reg(DM644X_HPIEN_DISABLE); + davinci_cfg_reg(DM644X_ATAEN_DISABLE); + + /* only one device will be jumpered and detected */ + if (HAS_NAND) { + platform_device_register(&davinci_evm_nandflash_device); + evm_leds[7].default_trigger = "nand-disk"; + if (HAS_NOR) + pr_warning("WARNING: both NAND and NOR flash " + "are enabled; disable one of them.\n"); + } else if (HAS_NOR) + platform_device_register(&davinci_evm_norflash_device); + } + platform_add_devices(davinci_evm_devices, ARRAY_SIZE(davinci_evm_devices)); evm_init_i2c(); + + davinci_serial_init(&uart_config); + + /* Register the fixup for PHY on DaVinci */ + phy_register_fixup_for_uid(LXT971_PHY_ID, LXT971_PHY_MASK, + davinci_phy_fixup); + } static __init void davinci_evm_irq_init(void) { - davinci_init_common_hw(); davinci_irq_init(); } -MACHINE_START(DAVINCI_EVM, "DaVinci EVM") +MACHINE_START(DAVINCI_EVM, "DaVinci DM644x EVM") /* Maintainer: MontaVista Software <source@mvista.com> */ .phys_io = IO_PHYS, .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, diff --git a/arch/arm/mach-davinci/clock.c b/arch/arm/mach-davinci/clock.c index abb92b7eca0..f0baaa15a57 100644 --- a/arch/arm/mach-davinci/clock.c +++ b/arch/arm/mach-davinci/clock.c @@ -1,7 +1,8 @@ /* - * TI DaVinci clock config file + * Clock and PLL control for DaVinci devices * - * Copyright (C) 2006 Texas Instruments. + * Copyright (C) 2006-2007 Texas Instruments. + * Copyright (C) 2008-2009 Deep Root Systems, LLC * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -13,6 +14,7 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/errno.h> +#include <linux/clk.h> #include <linux/err.h> #include <linux/mutex.h> #include <linux/platform_device.h> @@ -21,98 +23,50 @@ #include <mach/hardware.h> #include <mach/psc.h> +#include <mach/cputype.h> #include "clock.h" -/* PLL/Reset register offsets */ -#define PLLM 0x110 - static LIST_HEAD(clocks); static DEFINE_MUTEX(clocks_mutex); static DEFINE_SPINLOCK(clockfw_lock); -static unsigned int commonrate; -static unsigned int armrate; -static unsigned int fixedrate = 27000000; /* 27 MHZ */ - -extern void davinci_psc_config(unsigned int domain, unsigned int id, char enable); - -/* - * Returns a clock. Note that we first try to use device id on the bus - * and clock name. If this fails, we try to use clock name only. - */ -struct clk *clk_get(struct device *dev, const char *id) +static unsigned psc_domain(struct clk *clk) { - struct clk *p, *clk = ERR_PTR(-ENOENT); - int idno; - - if (dev == NULL || dev->bus != &platform_bus_type) - idno = -1; - else - idno = to_platform_device(dev)->id; - - mutex_lock(&clocks_mutex); - - list_for_each_entry(p, &clocks, node) { - if (p->id == idno && - strcmp(id, p->name) == 0 && try_module_get(p->owner)) { - clk = p; - goto found; - } - } - - list_for_each_entry(p, &clocks, node) { - if (strcmp(id, p->name) == 0 && try_module_get(p->owner)) { - clk = p; - break; - } - } - -found: - mutex_unlock(&clocks_mutex); - - return clk; + return (clk->flags & PSC_DSP) + ? DAVINCI_GPSC_DSPDOMAIN + : DAVINCI_GPSC_ARMDOMAIN; } -EXPORT_SYMBOL(clk_get); -void clk_put(struct clk *clk) +static void __clk_enable(struct clk *clk) { - if (clk && !IS_ERR(clk)) - module_put(clk->owner); -} -EXPORT_SYMBOL(clk_put); - -static int __clk_enable(struct clk *clk) -{ - if (clk->flags & ALWAYS_ENABLED) - return 0; - - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, clk->lpsc, 1); - return 0; + if (clk->parent) + __clk_enable(clk->parent); + if (clk->usecount++ == 0 && (clk->flags & CLK_PSC)) + davinci_psc_config(psc_domain(clk), clk->lpsc, 1); } static void __clk_disable(struct clk *clk) { - if (clk->usecount) + if (WARN_ON(clk->usecount == 0)) return; - - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, clk->lpsc, 0); + if (--clk->usecount == 0 && !(clk->flags & CLK_PLL)) + davinci_psc_config(psc_domain(clk), clk->lpsc, 0); + if (clk->parent) + __clk_disable(clk->parent); } int clk_enable(struct clk *clk) { unsigned long flags; - int ret = 0; if (clk == NULL || IS_ERR(clk)) return -EINVAL; - if (clk->usecount++ == 0) { - spin_lock_irqsave(&clockfw_lock, flags); - ret = __clk_enable(clk); - spin_unlock_irqrestore(&clockfw_lock, flags); - } + spin_lock_irqsave(&clockfw_lock, flags); + __clk_enable(clk); + spin_unlock_irqrestore(&clockfw_lock, flags); - return ret; + return 0; } EXPORT_SYMBOL(clk_enable); @@ -123,11 +77,9 @@ void clk_disable(struct clk *clk) if (clk == NULL || IS_ERR(clk)) return; - if (clk->usecount > 0 && !(--clk->usecount)) { - spin_lock_irqsave(&clockfw_lock, flags); - __clk_disable(clk); - spin_unlock_irqrestore(&clockfw_lock, flags); - } + spin_lock_irqsave(&clockfw_lock, flags); + __clk_disable(clk); + spin_unlock_irqrestore(&clockfw_lock, flags); } EXPORT_SYMBOL(clk_disable); @@ -136,7 +88,7 @@ unsigned long clk_get_rate(struct clk *clk) if (clk == NULL || IS_ERR(clk)) return -EINVAL; - return *(clk->rate); + return clk->rate; } EXPORT_SYMBOL(clk_get_rate); @@ -145,7 +97,7 @@ long clk_round_rate(struct clk *clk, unsigned long rate) if (clk == NULL || IS_ERR(clk)) return -EINVAL; - return *(clk->rate); + return clk->rate; } EXPORT_SYMBOL(clk_round_rate); @@ -164,10 +116,23 @@ int clk_register(struct clk *clk) if (clk == NULL || IS_ERR(clk)) return -EINVAL; + if (WARN(clk->parent && !clk->parent->rate, + "CLK: %s parent %s has no rate!\n", + clk->name, clk->parent->name)) + return -EINVAL; + mutex_lock(&clocks_mutex); - list_add(&clk->node, &clocks); + list_add_tail(&clk->node, &clocks); mutex_unlock(&clocks_mutex); + /* If rate is already set, use it */ + if (clk->rate) + return 0; + + /* Otherwise, default to parent rate */ + if (clk->parent) + clk->rate = clk->parent->rate; + return 0; } EXPORT_SYMBOL(clk_register); @@ -183,84 +148,150 @@ void clk_unregister(struct clk *clk) } EXPORT_SYMBOL(clk_unregister); -static struct clk davinci_clks[] = { - { - .name = "ARMCLK", - .rate = &armrate, - .lpsc = -1, - .flags = ALWAYS_ENABLED, - }, - { - .name = "UART", - .rate = &fixedrate, - .lpsc = DAVINCI_LPSC_UART0, - }, - { - .name = "EMACCLK", - .rate = &commonrate, - .lpsc = DAVINCI_LPSC_EMAC_WRAPPER, - }, - { - .name = "I2CCLK", - .rate = &fixedrate, - .lpsc = DAVINCI_LPSC_I2C, - }, - { - .name = "IDECLK", - .rate = &commonrate, - .lpsc = DAVINCI_LPSC_ATA, - }, - { - .name = "McBSPCLK", - .rate = &commonrate, - .lpsc = DAVINCI_LPSC_McBSP, - }, - { - .name = "MMCSDCLK", - .rate = &commonrate, - .lpsc = DAVINCI_LPSC_MMC_SD, - }, - { - .name = "SPICLK", - .rate = &commonrate, - .lpsc = DAVINCI_LPSC_SPI, - }, - { - .name = "gpio", - .rate = &commonrate, - .lpsc = DAVINCI_LPSC_GPIO, - }, - { - .name = "usb", - .rate = &commonrate, - .lpsc = DAVINCI_LPSC_USB, - }, - { - .name = "AEMIFCLK", - .rate = &commonrate, - .lpsc = DAVINCI_LPSC_AEMIF, - .usecount = 1, +#ifdef CONFIG_DAVINCI_RESET_CLOCKS +/* + * Disable any unused clocks left on by the bootloader + */ +static int __init clk_disable_unused(void) +{ + struct clk *ck; + + spin_lock_irq(&clockfw_lock); + list_for_each_entry(ck, &clocks, node) { + if (ck->usecount > 0) + continue; + if (!(ck->flags & CLK_PSC)) + continue; + + /* ignore if in Disabled or SwRstDisable states */ + if (!davinci_psc_is_clk_active(ck->lpsc)) + continue; + + pr_info("Clocks: disable unused %s\n", ck->name); + davinci_psc_config(psc_domain(ck), ck->lpsc, 0); } -}; + spin_unlock_irq(&clockfw_lock); + + return 0; +} +late_initcall(clk_disable_unused); +#endif -int __init davinci_clk_init(void) +static void clk_sysclk_recalc(struct clk *clk) { - struct clk *clkp; - int count = 0; - u32 pll_mult; - - pll_mult = davinci_readl(DAVINCI_PLL_CNTRL0_BASE + PLLM); - commonrate = ((pll_mult + 1) * 27000000) / 6; - armrate = ((pll_mult + 1) * 27000000) / 2; - - for (clkp = davinci_clks; count < ARRAY_SIZE(davinci_clks); - count++, clkp++) { - clk_register(clkp); - - /* Turn on clocks that have been enabled in the - * table above */ - if (clkp->usecount) - clk_enable(clkp); + u32 v, plldiv; + struct pll_data *pll; + + /* If this is the PLL base clock, no more calculations needed */ + if (clk->pll_data) + return; + + if (WARN_ON(!clk->parent)) + return; + + clk->rate = clk->parent->rate; + + /* Otherwise, the parent must be a PLL */ + if (WARN_ON(!clk->parent->pll_data)) + return; + + pll = clk->parent->pll_data; + + /* If pre-PLL, source clock is before the multiplier and divider(s) */ + if (clk->flags & PRE_PLL) + clk->rate = pll->input_rate; + + if (!clk->div_reg) + return; + + v = __raw_readl(pll->base + clk->div_reg); + if (v & PLLDIV_EN) { + plldiv = (v & PLLDIV_RATIO_MASK) + 1; + if (plldiv) + clk->rate /= plldiv; + } +} + +static void __init clk_pll_init(struct clk *clk) +{ + u32 ctrl, mult = 1, prediv = 1, postdiv = 1; + u8 bypass; + struct pll_data *pll = clk->pll_data; + + pll->base = IO_ADDRESS(pll->phys_base); + ctrl = __raw_readl(pll->base + PLLCTL); + clk->rate = pll->input_rate = clk->parent->rate; + + if (ctrl & PLLCTL_PLLEN) { + bypass = 0; + mult = __raw_readl(pll->base + PLLM); + mult = (mult & PLLM_PLLM_MASK) + 1; + } else + bypass = 1; + + if (pll->flags & PLL_HAS_PREDIV) { + prediv = __raw_readl(pll->base + PREDIV); + if (prediv & PLLDIV_EN) + prediv = (prediv & PLLDIV_RATIO_MASK) + 1; + else + prediv = 1; + } + + /* pre-divider is fixed, but (some?) chips won't report that */ + if (cpu_is_davinci_dm355() && pll->num == 1) + prediv = 8; + + if (pll->flags & PLL_HAS_POSTDIV) { + postdiv = __raw_readl(pll->base + POSTDIV); + if (postdiv & PLLDIV_EN) + postdiv = (postdiv & PLLDIV_RATIO_MASK) + 1; + else + postdiv = 1; + } + + if (!bypass) { + clk->rate /= prediv; + clk->rate *= mult; + clk->rate /= postdiv; + } + + pr_debug("PLL%d: input = %lu MHz [ ", + pll->num, clk->parent->rate / 1000000); + if (bypass) + pr_debug("bypass "); + if (prediv > 1) + pr_debug("/ %d ", prediv); + if (mult > 1) + pr_debug("* %d ", mult); + if (postdiv > 1) + pr_debug("/ %d ", postdiv); + pr_debug("] --> %lu MHz output.\n", clk->rate / 1000000); +} + +int __init davinci_clk_init(struct davinci_clk *clocks) + { + struct davinci_clk *c; + struct clk *clk; + + for (c = clocks; c->lk.clk; c++) { + clk = c->lk.clk; + + if (clk->pll_data) + clk_pll_init(clk); + + /* Calculate rates for PLL-derived clocks */ + else if (clk->flags & CLK_PLL) + clk_sysclk_recalc(clk); + + if (clk->lpsc) + clk->flags |= CLK_PSC; + + clkdev_add(&c->lk); + clk_register(clk); + + /* Turn on clocks that Linux doesn't otherwise manage */ + if (clk->flags & ALWAYS_ENABLED) + clk_enable(clk); } return 0; @@ -285,12 +316,52 @@ static void davinci_ck_stop(struct seq_file *m, void *v) { } -static int davinci_ck_show(struct seq_file *m, void *v) +#define CLKNAME_MAX 10 /* longest clock name */ +#define NEST_DELTA 2 +#define NEST_MAX 4 + +static void +dump_clock(struct seq_file *s, unsigned nest, struct clk *parent) { - struct clk *cp; + char *state; + char buf[CLKNAME_MAX + NEST_DELTA * NEST_MAX]; + struct clk *clk; + unsigned i; + + if (parent->flags & CLK_PLL) + state = "pll"; + else if (parent->flags & CLK_PSC) + state = "psc"; + else + state = ""; + + /* <nest spaces> name <pad to end> */ + memset(buf, ' ', sizeof(buf) - 1); + buf[sizeof(buf) - 1] = 0; + i = strlen(parent->name); + memcpy(buf + nest, parent->name, + min(i, (unsigned)(sizeof(buf) - 1 - nest))); + + seq_printf(s, "%s users=%2d %-3s %9ld Hz\n", + buf, parent->usecount, state, clk_get_rate(parent)); + /* REVISIT show device associations too */ + + /* cost is now small, but not linear... */ + list_for_each_entry(clk, &clocks, node) { + if (clk->parent == parent) + dump_clock(s, nest + NEST_DELTA, clk); + } +} - list_for_each_entry(cp, &clocks, node) - seq_printf(m,"%s %d %d\n", cp->name, *(cp->rate), cp->usecount); +static int davinci_ck_show(struct seq_file *m, void *v) +{ + /* Show clock tree; we know the main oscillator is first. + * We trust nonzero usecounts equate to PSC enables... + */ + mutex_lock(&clocks_mutex); + if (!list_empty(&clocks)) + dump_clock(m, 0, list_first_entry(&clocks, struct clk, node)); + mutex_unlock(&clocks_mutex); return 0; } @@ -321,4 +392,4 @@ static int __init davinci_ck_proc_init(void) } __initcall(davinci_ck_proc_init); -#endif /* CONFIG_DEBUG_PROC_FS */ +#endif /* CONFIG_DEBUG_PROC_FS */ diff --git a/arch/arm/mach-davinci/clock.h b/arch/arm/mach-davinci/clock.h index ed47079a52e..35736ec202f 100644 --- a/arch/arm/mach-davinci/clock.h +++ b/arch/arm/mach-davinci/clock.h @@ -1,7 +1,8 @@ /* * TI DaVinci clock definitions * - * Copyright (C) 2006 Texas Instruments. + * Copyright (C) 2006-2007 Texas Instruments. + * Copyright (C) 2008-2009 Deep Root Systems, LLC * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -11,23 +12,85 @@ #ifndef __ARCH_ARM_DAVINCI_CLOCK_H #define __ARCH_ARM_DAVINCI_CLOCK_H +#include <linux/list.h> +#include <asm/clkdev.h> + +#define DAVINCI_PLL1_BASE 0x01c40800 +#define DAVINCI_PLL2_BASE 0x01c40c00 +#define MAX_PLL 2 + +/* PLL/Reset register offsets */ +#define PLLCTL 0x100 +#define PLLCTL_PLLEN BIT(0) +#define PLLCTL_CLKMODE BIT(8) + +#define PLLM 0x110 +#define PLLM_PLLM_MASK 0xff + +#define PREDIV 0x114 +#define PLLDIV1 0x118 +#define PLLDIV2 0x11c +#define PLLDIV3 0x120 +#define POSTDIV 0x128 +#define BPDIV 0x12c +#define PLLCMD 0x138 +#define PLLSTAT 0x13c +#define PLLALNCTL 0x140 +#define PLLDCHANGE 0x144 +#define PLLCKEN 0x148 +#define PLLCKSTAT 0x14c +#define PLLSYSTAT 0x150 +#define PLLDIV4 0x160 +#define PLLDIV5 0x164 +#define PLLDIV6 0x168 +#define PLLDIV7 0x16c +#define PLLDIV8 0x170 +#define PLLDIV9 0x174 +#define PLLDIV_EN BIT(15) +#define PLLDIV_RATIO_MASK 0x1f + +struct pll_data { + u32 phys_base; + void __iomem *base; + u32 num; + u32 flags; + u32 input_rate; +}; +#define PLL_HAS_PREDIV 0x01 +#define PLL_HAS_POSTDIV 0x02 + struct clk { struct list_head node; struct module *owner; const char *name; - unsigned int *rate; - int id; - __s8 usecount; - __u8 flags; - __u8 lpsc; + unsigned long rate; + u8 usecount; + u8 flags; + u8 lpsc; + struct clk *parent; + struct pll_data *pll_data; + u32 div_reg; }; /* Clock flags */ -#define RATE_CKCTL 1 -#define RATE_FIXED 2 -#define RATE_PROPAGATES 4 -#define VIRTUAL_CLOCK 8 -#define ALWAYS_ENABLED 16 -#define ENABLE_REG_32BIT 32 +#define ALWAYS_ENABLED BIT(1) +#define CLK_PSC BIT(2) +#define PSC_DSP BIT(3) /* PSC uses DSP domain, not ARM */ +#define CLK_PLL BIT(4) /* PLL-derived clock */ +#define PRE_PLL BIT(5) /* source is before PLL mult/div */ + +struct davinci_clk { + struct clk_lookup lk; +}; + +#define CLK(dev, con, ck) \ + { \ + .lk = { \ + .dev_id = dev, \ + .con_id = con, \ + .clk = ck, \ + }, \ + } +int davinci_clk_init(struct davinci_clk *clocks); #endif diff --git a/arch/arm/mach-davinci/devices.c b/arch/arm/mach-davinci/devices.c index 808633f9f03..a31370b93dd 100644 --- a/arch/arm/mach-davinci/devices.c +++ b/arch/arm/mach-davinci/devices.c @@ -21,6 +21,10 @@ #include <mach/hardware.h> #include <mach/i2c.h> #include <mach/irqs.h> +#include <mach/cputype.h> +#include <mach/mux.h> + +#define DAVINCI_I2C_BASE 0x01C21000 static struct resource i2c_resources[] = { { @@ -43,6 +47,9 @@ static struct platform_device davinci_i2c_device = { void __init davinci_init_i2c(struct davinci_i2c_platform_data *pdata) { + if (cpu_is_davinci_dm644x()) + davinci_cfg_reg(DM644X_I2C); + davinci_i2c_device.dev.platform_data = pdata; (void) platform_device_register(&davinci_i2c_device); } diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c new file mode 100644 index 00000000000..d428ef192ea --- /dev/null +++ b/arch/arm/mach-davinci/dm644x.c @@ -0,0 +1,461 @@ +/* + * TI DaVinci DM644x chip specific setup + * + * Author: Kevin Hilman, Deep Root Systems, LLC + * + * 2007 (c) Deep Root Systems, LLC. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/clk.h> +#include <linux/platform_device.h> + +#include <mach/dm644x.h> +#include <mach/clock.h> +#include <mach/cputype.h> +#include <mach/edma.h> +#include <mach/irqs.h> +#include <mach/psc.h> +#include <mach/mux.h> + +#include "clock.h" +#include "mux.h" + +/* + * Device specific clocks + */ +#define DM644X_REF_FREQ 27000000 + +static struct pll_data pll1_data = { + .num = 1, + .phys_base = DAVINCI_PLL1_BASE, +}; + +static struct pll_data pll2_data = { + .num = 2, + .phys_base = DAVINCI_PLL2_BASE, +}; + +static struct clk ref_clk = { + .name = "ref_clk", + .rate = DM644X_REF_FREQ, +}; + +static struct clk pll1_clk = { + .name = "pll1", + .parent = &ref_clk, + .pll_data = &pll1_data, + .flags = CLK_PLL, +}; + +static struct clk pll1_sysclk1 = { + .name = "pll1_sysclk1", + .parent = &pll1_clk, + .flags = CLK_PLL, + .div_reg = PLLDIV1, +}; + +static struct clk pll1_sysclk2 = { + .name = "pll1_sysclk2", + .parent = &pll1_clk, + .flags = CLK_PLL, + .div_reg = PLLDIV2, +}; + +static struct clk pll1_sysclk3 = { + .name = "pll1_sysclk3", + .parent = &pll1_clk, + .flags = CLK_PLL, + .div_reg = PLLDIV3, +}; + +static struct clk pll1_sysclk5 = { + .name = "pll1_sysclk5", + .parent = &pll1_clk, + .flags = CLK_PLL, + .div_reg = PLLDIV5, +}; + +static struct clk pll1_aux_clk = { + .name = "pll1_aux_clk", + .parent = &pll1_clk, + .flags = CLK_PLL | PRE_PLL, +}; + +static struct clk pll1_sysclkbp = { + .name = "pll1_sysclkbp", + .parent = &pll1_clk, + .flags = CLK_PLL | PRE_PLL, + .div_reg = BPDIV +}; + +static struct clk pll2_clk = { + .name = "pll2", + .parent = &ref_clk, + .pll_data = &pll2_data, + .flags = CLK_PLL, +}; + +static struct clk pll2_sysclk1 = { + .name = "pll2_sysclk1", + .parent = &pll2_clk, + .flags = CLK_PLL, + .div_reg = PLLDIV1, +}; + +static struct clk pll2_sysclk2 = { + .name = "pll2_sysclk2", + .parent = &pll2_clk, + .flags = CLK_PLL, + .div_reg = PLLDIV2, +}; + +static struct clk pll2_sysclkbp = { + .name = "pll2_sysclkbp", + .parent = &pll2_clk, + .flags = CLK_PLL | PRE_PLL, + .div_reg = BPDIV +}; + +static struct clk dsp_clk = { + .name = "dsp", + .parent = &pll1_sysclk1, + .lpsc = DAVINCI_LPSC_GEM, + .flags = PSC_DSP, + .usecount = 1, /* REVISIT how to disable? */ +}; + +static struct clk arm_clk = { + .name = "arm", + .parent = &pll1_sysclk2, + .lpsc = DAVINCI_LPSC_ARM, + .flags = ALWAYS_ENABLED, +}; + +static struct clk vicp_clk = { + .name = "vicp", + .parent = &pll1_sysclk2, + .lpsc = DAVINCI_LPSC_IMCOP, + .flags = PSC_DSP, + .usecount = 1, /* REVISIT how to disable? */ +}; + +static struct clk vpss_master_clk = { + .name = "vpss_master", + .parent = &pll1_sysclk3, + .lpsc = DAVINCI_LPSC_VPSSMSTR, + .flags = CLK_PSC, +}; + +static struct clk vpss_slave_clk = { + .name = "vpss_slave", + .parent = &pll1_sysclk3, + .lpsc = DAVINCI_LPSC_VPSSSLV, +}; + +static struct clk uart0_clk = { + .name = "uart0", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_UART0, +}; + +static struct clk uart1_clk = { + .name = "uart1", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_UART1, +}; + +static struct clk uart2_clk = { + .name = "uart2", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_UART2, +}; + +static struct clk emac_clk = { + .name = "emac", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_EMAC_WRAPPER, +}; + +static struct clk i2c_clk = { + .name = "i2c", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_I2C, +}; + +static struct clk ide_clk = { + .name = "ide", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_ATA, +}; + +static struct clk asp_clk = { + .name = "asp0", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_McBSP, +}; + +static struct clk mmcsd_clk = { + .name = "mmcsd", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_MMC_SD, +}; + +static struct clk spi_clk = { + .name = "spi", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_SPI, +}; + +static struct clk gpio_clk = { + .name = "gpio", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_GPIO, +}; + +static struct clk usb_clk = { + .name = "usb", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_USB, +}; + +static struct clk vlynq_clk = { + .name = "vlynq", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_VLYNQ, +}; + +static struct clk aemif_clk = { + .name = "aemif", + .parent = &pll1_sysclk5, + .lpsc = DAVINCI_LPSC_AEMIF, +}; + +static struct clk pwm0_clk = { + .name = "pwm0", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_PWM0, +}; + +static struct clk pwm1_clk = { + .name = "pwm1", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_PWM1, +}; + +static struct clk pwm2_clk = { + .name = "pwm2", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_PWM2, +}; + +static struct clk timer0_clk = { + .name = "timer0", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_TIMER0, +}; + +static struct clk timer1_clk = { + .name = "timer1", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_TIMER1, +}; + +static struct clk timer2_clk = { + .name = "timer2", + .parent = &pll1_aux_clk, + .lpsc = DAVINCI_LPSC_TIMER2, + .usecount = 1, /* REVISIT: why cant' this be disabled? */ +}; + +struct davinci_clk dm644x_clks[] = { + CLK(NULL, "ref", &ref_clk), + CLK(NULL, "pll1", &pll1_clk), + CLK(NULL, "pll1_sysclk1", &pll1_sysclk1), + CLK(NULL, "pll1_sysclk2", &pll1_sysclk2), + CLK(NULL, "pll1_sysclk3", &pll1_sysclk3), + CLK(NULL, "pll1_sysclk5", &pll1_sysclk5), + CLK(NULL, "pll1_aux", &pll1_aux_clk), + CLK(NULL, "pll1_sysclkbp", &pll1_sysclkbp), + CLK(NULL, "pll2", &pll2_clk), + CLK(NULL, "pll2_sysclk1", &pll2_sysclk1), + CLK(NULL, "pll2_sysclk2", &pll2_sysclk2), + CLK(NULL, "pll2_sysclkbp", &pll2_sysclkbp), + CLK(NULL, "dsp", &dsp_clk), + CLK(NULL, "arm", &arm_clk), + CLK(NULL, "vicp", &vicp_clk), + CLK(NULL, "vpss_master", &vpss_master_clk), + CLK(NULL, "vpss_slave", &vpss_slave_clk), + CLK(NULL, "arm", &arm_clk), + CLK(NULL, "uart0", &uart0_clk), + CLK(NULL, "uart1", &uart1_clk), + CLK(NULL, "uart2", &uart2_clk), + CLK("davinci_emac.1", NULL, &emac_clk), + CLK("i2c_davinci.1", NULL, &i2c_clk), + CLK("palm_bk3710", NULL, &ide_clk), + CLK("soc-audio.0", NULL, &asp_clk), + CLK("davinci_mmc.0", NULL, &mmcsd_clk), + CLK(NULL, "spi", &spi_clk), + CLK(NULL, "gpio", &gpio_clk), + CLK(NULL, "usb", &usb_clk), + CLK(NULL, "vlynq", &vlynq_clk), + CLK(NULL, "aemif", &aemif_clk), + CLK(NULL, "pwm0", &pwm0_clk), + CLK(NULL, "pwm1", &pwm1_clk), + CLK(NULL, "pwm2", &pwm2_clk), + CLK(NULL, "timer0", &timer0_clk), + CLK(NULL, "timer1", &timer1_clk), + CLK("watchdog", NULL, &timer2_clk), + CLK(NULL, NULL, NULL), +}; + +#if defined(CONFIG_TI_DAVINCI_EMAC) || defined(CONFIG_TI_DAVINCI_EMAC_MODULE) + +static struct resource dm644x_emac_resources[] = { + { + .start = DM644X_EMAC_BASE, + .end = DM644X_EMAC_BASE + 0x47ff, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_EMACINT, + .end = IRQ_EMACINT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device dm644x_emac_device = { + .name = "davinci_emac", + .id = 1, + .num_resources = ARRAY_SIZE(dm644x_emac_resources), + .resource = dm644x_emac_resources, +}; + +#endif + +/* + * Device specific mux setup + * + * soc description mux mode mode mux dbg + * reg offset mask mode + */ +static const struct mux_config dm644x_pins[] = { +MUX_CFG(DM644X, HDIREN, 0, 16, 1, 1, true) +MUX_CFG(DM644X, ATAEN, 0, 17, 1, 1, true) +MUX_CFG(DM644X, ATAEN_DISABLE, 0, 17, 1, 0, true) + +MUX_CFG(DM644X, HPIEN_DISABLE, 0, 29, 1, 0, true) + +MUX_CFG(DM644X, AEAW, 0, 0, 31, 31, true) + +MUX_CFG(DM644X, MSTK, 1, 9, 1, 0, false) + +MUX_CFG(DM644X, I2C, 1, 7, 1, 1, false) + +MUX_CFG(DM644X, MCBSP, 1, 10, 1, 1, false) + +MUX_CFG(DM644X, UART1, 1, 1, 1, 1, true) +MUX_CFG(DM644X, UART2, 1, 2, 1, 1, true) + +MUX_CFG(DM644X, PWM0, 1, 4, 1, 1, false) + +MUX_CFG(DM644X, PWM1, 1, 5, 1, 1, false) + +MUX_CFG(DM644X, PWM2, 1, 6, 1, 1, false) + +MUX_CFG(DM644X, VLYNQEN, 0, 15, 1, 1, false) +MUX_CFG(DM644X, VLSCREN, 0, 14, 1, 1, false) +MUX_CFG(DM644X, VLYNQWD, 0, 12, 3, 3, false) + +MUX_CFG(DM644X, EMACEN, 0, 31, 1, 1, true) + +MUX_CFG(DM644X, GPIO3V, 0, 31, 1, 0, true) + +MUX_CFG(DM644X, GPIO0, 0, 24, 1, 0, true) +MUX_CFG(DM644X, GPIO3, 0, 25, 1, 0, false) +MUX_CFG(DM644X, GPIO43_44, 1, 7, 1, 0, false) +MUX_CFG(DM644X, GPIO46_47, 0, 22, 1, 0, true) + +MUX_CFG(DM644X, RGB666, 0, 22, 1, 1, true) + +MUX_CFG(DM644X, LOEEN, 0, 24, 1, 1, true) +MUX_CFG(DM644X, LFLDEN, 0, 25, 1, 1, false) +}; + + +/*----------------------------------------------------------------------*/ + +static const s8 dma_chan_dm644x_no_event[] = { + 0, 1, 12, 13, 14, + 15, 25, 30, 31, 45, + 46, 47, 55, 56, 57, + 58, 59, 60, 61, 62, + 63, + -1 +}; + +static struct edma_soc_info dm644x_edma_info = { + .n_channel = 64, + .n_region = 4, + .n_slot = 128, + .n_tc = 2, + .noevent = dma_chan_dm644x_no_event, +}; + +static struct resource edma_resources[] = { + { + .name = "edma_cc", + .start = 0x01c00000, + .end = 0x01c00000 + SZ_64K - 1, + .flags = IORESOURCE_MEM, + }, + { + .name = "edma_tc0", + .start = 0x01c10000, + .end = 0x01c10000 + SZ_1K - 1, + .flags = IORESOURCE_MEM, + }, + { + .name = "edma_tc1", + .start = 0x01c10400, + .end = 0x01c10400 + SZ_1K - 1, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_CCINT0, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_CCERRINT, + .flags = IORESOURCE_IRQ, + }, + /* not using TC*_ERR */ +}; + +static struct platform_device dm644x_edma_device = { + .name = "edma", + .id = -1, + .dev.platform_data = &dm644x_edma_info, + .num_resources = ARRAY_SIZE(edma_resources), + .resource = edma_resources, +}; + +/*----------------------------------------------------------------------*/ +void __init dm644x_init(void) +{ + davinci_clk_init(dm644x_clks); + davinci_mux_register(dm644x_pins, ARRAY_SIZE(dm644x_pins)); +} + +static int __init dm644x_init_devices(void) +{ + if (!cpu_is_davinci_dm644x()) + return 0; + + platform_device_register(&dm644x_edma_device); + return 0; +} +postcore_initcall(dm644x_init_devices); diff --git a/arch/arm/mach-davinci/dma.c b/arch/arm/mach-davinci/dma.c new file mode 100644 index 00000000000..15e9eb158bb --- /dev/null +++ b/arch/arm/mach-davinci/dma.c @@ -0,0 +1,1135 @@ +/* + * EDMA3 support for DaVinci + * + * Copyright (C) 2006-2009 Texas Instruments. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include <linux/kernel.h> +#include <linux/sched.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/spinlock.h> +#include <linux/compiler.h> +#include <linux/io.h> + +#include <mach/cputype.h> +#include <mach/memory.h> +#include <mach/hardware.h> +#include <mach/irqs.h> +#include <mach/edma.h> +#include <mach/mux.h> + + +/* Offsets matching "struct edmacc_param" */ +#define PARM_OPT 0x00 +#define PARM_SRC 0x04 +#define PARM_A_B_CNT 0x08 +#define PARM_DST 0x0c +#define PARM_SRC_DST_BIDX 0x10 +#define PARM_LINK_BCNTRLD 0x14 +#define PARM_SRC_DST_CIDX 0x18 +#define PARM_CCNT 0x1c + +#define PARM_SIZE 0x20 + +/* Offsets for EDMA CC global channel registers and their shadows */ +#define SH_ER 0x00 /* 64 bits */ +#define SH_ECR 0x08 /* 64 bits */ +#define SH_ESR 0x10 /* 64 bits */ +#define SH_CER 0x18 /* 64 bits */ +#define SH_EER 0x20 /* 64 bits */ +#define SH_EECR 0x28 /* 64 bits */ +#define SH_EESR 0x30 /* 64 bits */ +#define SH_SER 0x38 /* 64 bits */ +#define SH_SECR 0x40 /* 64 bits */ +#define SH_IER 0x50 /* 64 bits */ +#define SH_IECR 0x58 /* 64 bits */ +#define SH_IESR 0x60 /* 64 bits */ +#define SH_IPR 0x68 /* 64 bits */ +#define SH_ICR 0x70 /* 64 bits */ +#define SH_IEVAL 0x78 +#define SH_QER 0x80 +#define SH_QEER 0x84 +#define SH_QEECR 0x88 +#define SH_QEESR 0x8c +#define SH_QSER 0x90 +#define SH_QSECR 0x94 +#define SH_SIZE 0x200 + +/* Offsets for EDMA CC global registers */ +#define EDMA_REV 0x0000 +#define EDMA_CCCFG 0x0004 +#define EDMA_QCHMAP 0x0200 /* 8 registers */ +#define EDMA_DMAQNUM 0x0240 /* 8 registers (4 on OMAP-L1xx) */ +#define EDMA_QDMAQNUM 0x0260 +#define EDMA_QUETCMAP 0x0280 +#define EDMA_QUEPRI 0x0284 +#define EDMA_EMR 0x0300 /* 64 bits */ +#define EDMA_EMCR 0x0308 /* 64 bits */ +#define EDMA_QEMR 0x0310 +#define EDMA_QEMCR 0x0314 +#define EDMA_CCERR 0x0318 +#define EDMA_CCERRCLR 0x031c +#define EDMA_EEVAL 0x0320 +#define EDMA_DRAE 0x0340 /* 4 x 64 bits*/ +#define EDMA_QRAE 0x0380 /* 4 registers */ +#define EDMA_QUEEVTENTRY 0x0400 /* 2 x 16 registers */ +#define EDMA_QSTAT 0x0600 /* 2 registers */ +#define EDMA_QWMTHRA 0x0620 +#define EDMA_QWMTHRB 0x0624 +#define EDMA_CCSTAT 0x0640 + +#define EDMA_M 0x1000 /* global channel registers */ +#define EDMA_ECR 0x1008 +#define EDMA_ECRH 0x100C +#define EDMA_SHADOW0 0x2000 /* 4 regions shadowing global channels */ +#define EDMA_PARM 0x4000 /* 128 param entries */ + +#define DAVINCI_DMA_3PCC_BASE 0x01C00000 + +#define PARM_OFFSET(param_no) (EDMA_PARM + ((param_no) << 5)) + +#define EDMA_MAX_DMACH 64 +#define EDMA_MAX_PARAMENTRY 512 +#define EDMA_MAX_EVQUE 2 /* FIXME too small */ + + +/*****************************************************************************/ + +static void __iomem *edmacc_regs_base; + +static inline unsigned int edma_read(int offset) +{ + return (unsigned int)__raw_readl(edmacc_regs_base + offset); +} + +static inline void edma_write(int offset, int val) +{ + __raw_writel(val, edmacc_regs_base + offset); +} +static inline void edma_modify(int offset, unsigned and, unsigned or) +{ + unsigned val = edma_read(offset); + val &= and; + val |= or; + edma_write(offset, val); +} +static inline void edma_and(int offset, unsigned and) +{ + unsigned val = edma_read(offset); + val &= and; + edma_write(offset, val); +} +static inline void edma_or(int offset, unsigned or) +{ + unsigned val = edma_read(offset); + val |= or; + edma_write(offset, val); +} +static inline unsigned int edma_read_array(int offset, int i) +{ + return edma_read(offset + (i << 2)); +} +static inline void edma_write_array(int offset, int i, unsigned val) +{ + edma_write(offset + (i << 2), val); +} +static inline void edma_modify_array(int offset, int i, + unsigned and, unsigned or) +{ + edma_modify(offset + (i << 2), and, or); +} +static inline void edma_or_array(int offset, int i, unsigned or) +{ + edma_or(offset + (i << 2), or); +} +static inline void edma_or_array2(int offset, int i, int j, unsigned or) +{ + edma_or(offset + ((i*2 + j) << 2), or); +} +static inline void edma_write_array2(int offset, int i, int j, unsigned val) +{ + edma_write(offset + ((i*2 + j) << 2), val); +} +static inline unsigned int edma_shadow0_read(int offset) +{ + return edma_read(EDMA_SHADOW0 + offset); +} +static inline unsigned int edma_shadow0_read_array(int offset, int i) +{ + return edma_read(EDMA_SHADOW0 + offset + (i << 2)); +} +static inline void edma_shadow0_write(int offset, unsigned val) +{ + edma_write(EDMA_SHADOW0 + offset, val); +} +static inline void edma_shadow0_write_array(int offset, int i, unsigned val) +{ + edma_write(EDMA_SHADOW0 + offset + (i << 2), val); +} +static inline unsigned int edma_parm_read(int offset, int param_no) +{ + return edma_read(EDMA_PARM + offset + (param_no << 5)); +} +static inline void edma_parm_write(int offset, int param_no, unsigned val) +{ + edma_write(EDMA_PARM + offset + (param_no << 5), val); +} +static inline void edma_parm_modify(int offset, int param_no, + unsigned and, unsigned or) +{ + edma_modify(EDMA_PARM + offset + (param_no << 5), and, or); +} +static inline void edma_parm_and(int offset, int param_no, unsigned and) +{ + edma_and(EDMA_PARM + offset + (param_no << 5), and); +} +static inline void edma_parm_or(int offset, int param_no, unsigned or) +{ + edma_or(EDMA_PARM + offset + (param_no << 5), or); +} + +/*****************************************************************************/ + +/* actual number of DMA channels and slots on this silicon */ +static unsigned num_channels; +static unsigned num_slots; + +static struct dma_interrupt_data { + void (*callback)(unsigned channel, unsigned short ch_status, + void *data); + void *data; +} intr_data[EDMA_MAX_DMACH]; + +/* The edma_inuse bit for each PaRAM slot is clear unless the + * channel is in use ... by ARM or DSP, for QDMA, or whatever. + */ +static DECLARE_BITMAP(edma_inuse, EDMA_MAX_PARAMENTRY); + +/* The edma_noevent bit for each channel is clear unless + * it doesn't trigger DMA events on this platform. It uses a + * bit of SOC-specific initialization code. + */ +static DECLARE_BITMAP(edma_noevent, EDMA_MAX_DMACH); + +/* dummy param set used to (re)initialize parameter RAM slots */ +static const struct edmacc_param dummy_paramset = { + .link_bcntrld = 0xffff, + .ccnt = 1, +}; + +static const int __initconst +queue_tc_mapping[EDMA_MAX_EVQUE + 1][2] = { +/* {event queue no, TC no} */ + {0, 0}, + {1, 1}, + {-1, -1} +}; + +static const int __initconst +queue_priority_mapping[EDMA_MAX_EVQUE + 1][2] = { + /* {event queue no, Priority} */ + {0, 3}, + {1, 7}, + {-1, -1} +}; + +/*****************************************************************************/ + +static void map_dmach_queue(unsigned ch_no, enum dma_event_q queue_no) +{ + int bit = (ch_no & 0x7) * 4; + + /* default to low priority queue */ + if (queue_no == EVENTQ_DEFAULT) + queue_no = EVENTQ_1; + + queue_no &= 7; + edma_modify_array(EDMA_DMAQNUM, (ch_no >> 3), + ~(0x7 << bit), queue_no << bit); +} + +static void __init map_queue_tc(int queue_no, int tc_no) +{ + int bit = queue_no * 4; + edma_modify(EDMA_QUETCMAP, ~(0x7 << bit), ((tc_no & 0x7) << bit)); +} + +static void __init assign_priority_to_queue(int queue_no, int priority) +{ + int bit = queue_no * 4; + edma_modify(EDMA_QUEPRI, ~(0x7 << bit), ((priority & 0x7) << bit)); +} + +static inline void +setup_dma_interrupt(unsigned lch, + void (*callback)(unsigned channel, u16 ch_status, void *data), + void *data) +{ + if (!callback) { + edma_shadow0_write_array(SH_IECR, lch >> 5, + (1 << (lch & 0x1f))); + } + + intr_data[lch].callback = callback; + intr_data[lch].data = data; + + if (callback) { + edma_shadow0_write_array(SH_ICR, lch >> 5, + (1 << (lch & 0x1f))); + edma_shadow0_write_array(SH_IESR, lch >> 5, + (1 << (lch & 0x1f))); + } +} + +/****************************************************************************** + * + * DMA interrupt handler + * + *****************************************************************************/ +static irqreturn_t dma_irq_handler(int irq, void *data) +{ + int i; + unsigned int cnt = 0; + + dev_dbg(data, "dma_irq_handler\n"); + + if ((edma_shadow0_read_array(SH_IPR, 0) == 0) + && (edma_shadow0_read_array(SH_IPR, 1) == 0)) + return IRQ_NONE; + + while (1) { + int j; + if (edma_shadow0_read_array(SH_IPR, 0)) + j = 0; + else if (edma_shadow0_read_array(SH_IPR, 1)) + j = 1; + else + break; + dev_dbg(data, "IPR%d %08x\n", j, + edma_shadow0_read_array(SH_IPR, j)); + for (i = 0; i < 32; i++) { + int k = (j << 5) + i; + if (edma_shadow0_read_array(SH_IPR, j) & (1 << i)) { + /* Clear the corresponding IPR bits */ + edma_shadow0_write_array(SH_ICR, j, (1 << i)); + if (intr_data[k].callback) { + intr_data[k].callback(k, DMA_COMPLETE, + intr_data[k].data); + } + } + } + cnt++; + if (cnt > 10) + break; + } + edma_shadow0_write(SH_IEVAL, 1); + return IRQ_HANDLED; +} + +/****************************************************************************** + * + * DMA error interrupt handler + * + *****************************************************************************/ +static irqreturn_t dma_ccerr_handler(int irq, void *data) +{ + int i; + unsigned int cnt = 0; + + dev_dbg(data, "dma_ccerr_handler\n"); + + if ((edma_read_array(EDMA_EMR, 0) == 0) && + (edma_read_array(EDMA_EMR, 1) == 0) && + (edma_read(EDMA_QEMR) == 0) && (edma_read(EDMA_CCERR) == 0)) + return IRQ_NONE; + + while (1) { + int j = -1; + if (edma_read_array(EDMA_EMR, 0)) + j = 0; + else if (edma_read_array(EDMA_EMR, 1)) + j = 1; + if (j >= 0) { + dev_dbg(data, "EMR%d %08x\n", j, + edma_read_array(EDMA_EMR, j)); + for (i = 0; i < 32; i++) { + int k = (j << 5) + i; + if (edma_read_array(EDMA_EMR, j) & (1 << i)) { + /* Clear the corresponding EMR bits */ + edma_write_array(EDMA_EMCR, j, 1 << i); + /* Clear any SER */ + edma_shadow0_write_array(SH_SECR, j, + (1 << i)); + if (intr_data[k].callback) { + intr_data[k].callback(k, + DMA_CC_ERROR, + intr_data + [k].data); + } + } + } + } else if (edma_read(EDMA_QEMR)) { + dev_dbg(data, "QEMR %02x\n", + edma_read(EDMA_QEMR)); + for (i = 0; i < 8; i++) { + if (edma_read(EDMA_QEMR) & (1 << i)) { + /* Clear the corresponding IPR bits */ + edma_write(EDMA_QEMCR, 1 << i); + edma_shadow0_write(SH_QSECR, (1 << i)); + + /* NOTE: not reported!! */ + } + } + } else if (edma_read(EDMA_CCERR)) { + dev_dbg(data, "CCERR %08x\n", + edma_read(EDMA_CCERR)); + /* FIXME: CCERR.BIT(16) ignored! much better + * to just write CCERRCLR with CCERR value... + */ + for (i = 0; i < 8; i++) { + if (edma_read(EDMA_CCERR) & (1 << i)) { + /* Clear the corresponding IPR bits */ + edma_write(EDMA_CCERRCLR, 1 << i); + + /* NOTE: not reported!! */ + } + } + } + if ((edma_read_array(EDMA_EMR, 0) == 0) + && (edma_read_array(EDMA_EMR, 1) == 0) + && (edma_read(EDMA_QEMR) == 0) + && (edma_read(EDMA_CCERR) == 0)) { + break; + } + cnt++; + if (cnt > 10) + break; + } + edma_write(EDMA_EEVAL, 1); + return IRQ_HANDLED; +} + +/****************************************************************************** + * + * Transfer controller error interrupt handlers + * + *****************************************************************************/ + +#define tc_errs_handled false /* disabled as long as they're NOPs */ + +static irqreturn_t dma_tc0err_handler(int irq, void *data) +{ + dev_dbg(data, "dma_tc0err_handler\n"); + return IRQ_HANDLED; +} + +static irqreturn_t dma_tc1err_handler(int irq, void *data) +{ + dev_dbg(data, "dma_tc1err_handler\n"); + return IRQ_HANDLED; +} + +/*-----------------------------------------------------------------------*/ + +/* Resource alloc/free: dma channels, parameter RAM slots */ + +/** + * edma_alloc_channel - allocate DMA channel and paired parameter RAM + * @channel: specific channel to allocate; negative for "any unmapped channel" + * @callback: optional; to be issued on DMA completion or errors + * @data: passed to callback + * @eventq_no: an EVENTQ_* constant, used to choose which Transfer + * Controller (TC) executes requests using this channel. Use + * EVENTQ_DEFAULT unless you really need a high priority queue. + * + * This allocates a DMA channel and its associated parameter RAM slot. + * The parameter RAM is initialized to hold a dummy transfer. + * + * Normal use is to pass a specific channel number as @channel, to make + * use of hardware events mapped to that channel. When the channel will + * be used only for software triggering or event chaining, channels not + * mapped to hardware events (or mapped to unused events) are preferable. + * + * DMA transfers start from a channel using edma_start(), or by + * chaining. When the transfer described in that channel's parameter RAM + * slot completes, that slot's data may be reloaded through a link. + * + * DMA errors are only reported to the @callback associated with the + * channel driving that transfer, but transfer completion callbacks can + * be sent to another channel under control of the TCC field in + * the option word of the transfer's parameter RAM set. Drivers must not + * use DMA transfer completion callbacks for channels they did not allocate. + * (The same applies to TCC codes used in transfer chaining.) + * + * Returns the number of the channel, else negative errno. + */ +int edma_alloc_channel(int channel, + void (*callback)(unsigned channel, u16 ch_status, void *data), + void *data, + enum dma_event_q eventq_no) +{ + if (channel < 0) { + channel = 0; + for (;;) { + channel = find_next_bit(edma_noevent, + num_channels, channel); + if (channel == num_channels) + return -ENOMEM; + if (!test_and_set_bit(channel, edma_inuse)) + break; + channel++; + } + } else if (channel >= num_channels) { + return -EINVAL; + } else if (test_and_set_bit(channel, edma_inuse)) { + return -EBUSY; + } + + /* ensure access through shadow region 0 */ + edma_or_array2(EDMA_DRAE, 0, channel >> 5, 1 << (channel & 0x1f)); + + /* ensure no events are pending */ + edma_stop(channel); + memcpy_toio(edmacc_regs_base + PARM_OFFSET(channel), + &dummy_paramset, PARM_SIZE); + + if (callback) + setup_dma_interrupt(channel, callback, data); + + map_dmach_queue(channel, eventq_no); + + return channel; +} +EXPORT_SYMBOL(edma_alloc_channel); + + +/** + * edma_free_channel - deallocate DMA channel + * @channel: dma channel returned from edma_alloc_channel() + * + * This deallocates the DMA channel and associated parameter RAM slot + * allocated by edma_alloc_channel(). + * + * Callers are responsible for ensuring the channel is inactive, and + * will not be reactivated by linking, chaining, or software calls to + * edma_start(). + */ +void edma_free_channel(unsigned channel) +{ + if (channel >= num_channels) + return; + + setup_dma_interrupt(channel, NULL, NULL); + /* REVISIT should probably take out of shadow region 0 */ + + memcpy_toio(edmacc_regs_base + PARM_OFFSET(channel), + &dummy_paramset, PARM_SIZE); + clear_bit(channel, edma_inuse); +} +EXPORT_SYMBOL(edma_free_channel); + +/** + * edma_alloc_slot - allocate DMA parameter RAM + * @slot: specific slot to allocate; negative for "any unused slot" + * + * This allocates a parameter RAM slot, initializing it to hold a + * dummy transfer. Slots allocated using this routine have not been + * mapped to a hardware DMA channel, and will normally be used by + * linking to them from a slot associated with a DMA channel. + * + * Normal use is to pass EDMA_SLOT_ANY as the @slot, but specific + * slots may be allocated on behalf of DSP firmware. + * + * Returns the number of the slot, else negative errno. + */ +int edma_alloc_slot(int slot) +{ + if (slot < 0) { + slot = num_channels; + for (;;) { + slot = find_next_zero_bit(edma_inuse, + num_slots, slot); + if (slot == num_slots) + return -ENOMEM; + if (!test_and_set_bit(slot, edma_inuse)) + break; + } + } else if (slot < num_channels || slot >= num_slots) { + return -EINVAL; + } else if (test_and_set_bit(slot, edma_inuse)) { + return -EBUSY; + } + + memcpy_toio(edmacc_regs_base + PARM_OFFSET(slot), + &dummy_paramset, PARM_SIZE); + + return slot; +} +EXPORT_SYMBOL(edma_alloc_slot); + +/** + * edma_free_slot - deallocate DMA parameter RAM + * @slot: parameter RAM slot returned from edma_alloc_slot() + * + * This deallocates the parameter RAM slot allocated by edma_alloc_slot(). + * Callers are responsible for ensuring the slot is inactive, and will + * not be activated. + */ +void edma_free_slot(unsigned slot) +{ + if (slot < num_channels || slot >= num_slots) + return; + + memcpy_toio(edmacc_regs_base + PARM_OFFSET(slot), + &dummy_paramset, PARM_SIZE); + clear_bit(slot, edma_inuse); +} +EXPORT_SYMBOL(edma_free_slot); + +/*-----------------------------------------------------------------------*/ + +/* Parameter RAM operations (i) -- read/write partial slots */ + +/** + * edma_set_src - set initial DMA source address in parameter RAM slot + * @slot: parameter RAM slot being configured + * @src_port: physical address of source (memory, controller FIFO, etc) + * @addressMode: INCR, except in very rare cases + * @fifoWidth: ignored unless @addressMode is FIFO, else specifies the + * width to use when addressing the fifo (e.g. W8BIT, W32BIT) + * + * Note that the source address is modified during the DMA transfer + * according to edma_set_src_index(). + */ +void edma_set_src(unsigned slot, dma_addr_t src_port, + enum address_mode mode, enum fifo_width width) +{ + if (slot < num_slots) { + unsigned int i = edma_parm_read(PARM_OPT, slot); + + if (mode) { + /* set SAM and program FWID */ + i = (i & ~(EDMA_FWID)) | (SAM | ((width & 0x7) << 8)); + } else { + /* clear SAM */ + i &= ~SAM; + } + edma_parm_write(PARM_OPT, slot, i); + + /* set the source port address + in source register of param structure */ + edma_parm_write(PARM_SRC, slot, src_port); + } +} +EXPORT_SYMBOL(edma_set_src); + +/** + * edma_set_dest - set initial DMA destination address in parameter RAM slot + * @slot: parameter RAM slot being configured + * @dest_port: physical address of destination (memory, controller FIFO, etc) + * @addressMode: INCR, except in very rare cases + * @fifoWidth: ignored unless @addressMode is FIFO, else specifies the + * width to use when addressing the fifo (e.g. W8BIT, W32BIT) + * + * Note that the destination address is modified during the DMA transfer + * according to edma_set_dest_index(). + */ +void edma_set_dest(unsigned slot, dma_addr_t dest_port, + enum address_mode mode, enum fifo_width width) +{ + if (slot < num_slots) { + unsigned int i = edma_parm_read(PARM_OPT, slot); + + if (mode) { + /* set DAM and program FWID */ + i = (i & ~(EDMA_FWID)) | (DAM | ((width & 0x7) << 8)); + } else { + /* clear DAM */ + i &= ~DAM; + } + edma_parm_write(PARM_OPT, slot, i); + /* set the destination port address + in dest register of param structure */ + edma_parm_write(PARM_DST, slot, dest_port); + } +} +EXPORT_SYMBOL(edma_set_dest); + +/** + * edma_get_position - returns the current transfer points + * @slot: parameter RAM slot being examined + * @src: pointer to source port position + * @dst: pointer to destination port position + * + * Returns current source and destination addresses for a particular + * parameter RAM slot. Its channel should not be active when this is called. + */ +void edma_get_position(unsigned slot, dma_addr_t *src, dma_addr_t *dst) +{ + struct edmacc_param temp; + + edma_read_slot(slot, &temp); + if (src != NULL) + *src = temp.src; + if (dst != NULL) + *dst = temp.dst; +} +EXPORT_SYMBOL(edma_get_position); + +/** + * edma_set_src_index - configure DMA source address indexing + * @slot: parameter RAM slot being configured + * @src_bidx: byte offset between source arrays in a frame + * @src_cidx: byte offset between source frames in a block + * + * Offsets are specified to support either contiguous or discontiguous + * memory transfers, or repeated access to a hardware register, as needed. + * When accessing hardware registers, both offsets are normally zero. + */ +void edma_set_src_index(unsigned slot, s16 src_bidx, s16 src_cidx) +{ + if (slot < num_slots) { + edma_parm_modify(PARM_SRC_DST_BIDX, slot, + 0xffff0000, src_bidx); + edma_parm_modify(PARM_SRC_DST_CIDX, slot, + 0xffff0000, src_cidx); + } +} +EXPORT_SYMBOL(edma_set_src_index); + +/** + * edma_set_dest_index - configure DMA destination address indexing + * @slot: parameter RAM slot being configured + * @dest_bidx: byte offset between destination arrays in a frame + * @dest_cidx: byte offset between destination frames in a block + * + * Offsets are specified to support either contiguous or discontiguous + * memory transfers, or repeated access to a hardware register, as needed. + * When accessing hardware registers, both offsets are normally zero. + */ +void edma_set_dest_index(unsigned slot, s16 dest_bidx, s16 dest_cidx) +{ + if (slot < num_slots) { + edma_parm_modify(PARM_SRC_DST_BIDX, slot, + 0x0000ffff, dest_bidx << 16); + edma_parm_modify(PARM_SRC_DST_CIDX, slot, + 0x0000ffff, dest_cidx << 16); + } +} +EXPORT_SYMBOL(edma_set_dest_index); + +/** + * edma_set_transfer_params - configure DMA transfer parameters + * @slot: parameter RAM slot being configured + * @acnt: how many bytes per array (at least one) + * @bcnt: how many arrays per frame (at least one) + * @ccnt: how many frames per block (at least one) + * @bcnt_rld: used only for A-Synchronized transfers; this specifies + * the value to reload into bcnt when it decrements to zero + * @sync_mode: ASYNC or ABSYNC + * + * See the EDMA3 documentation to understand how to configure and link + * transfers using the fields in PaRAM slots. If you are not doing it + * all at once with edma_write_slot(), you will use this routine + * plus two calls each for source and destination, setting the initial + * address and saying how to index that address. + * + * An example of an A-Synchronized transfer is a serial link using a + * single word shift register. In that case, @acnt would be equal to + * that word size; the serial controller issues a DMA synchronization + * event to transfer each word, and memory access by the DMA transfer + * controller will be word-at-a-time. + * + * An example of an AB-Synchronized transfer is a device using a FIFO. + * In that case, @acnt equals the FIFO width and @bcnt equals its depth. + * The controller with the FIFO issues DMA synchronization events when + * the FIFO threshold is reached, and the DMA transfer controller will + * transfer one frame to (or from) the FIFO. It will probably use + * efficient burst modes to access memory. + */ +void edma_set_transfer_params(unsigned slot, + u16 acnt, u16 bcnt, u16 ccnt, + u16 bcnt_rld, enum sync_dimension sync_mode) +{ + if (slot < num_slots) { + edma_parm_modify(PARM_LINK_BCNTRLD, slot, + 0x0000ffff, bcnt_rld << 16); + if (sync_mode == ASYNC) + edma_parm_and(PARM_OPT, slot, ~SYNCDIM); + else + edma_parm_or(PARM_OPT, slot, SYNCDIM); + /* Set the acount, bcount, ccount registers */ + edma_parm_write(PARM_A_B_CNT, slot, (bcnt << 16) | acnt); + edma_parm_write(PARM_CCNT, slot, ccnt); + } +} +EXPORT_SYMBOL(edma_set_transfer_params); + +/** + * edma_link - link one parameter RAM slot to another + * @from: parameter RAM slot originating the link + * @to: parameter RAM slot which is the link target + * + * The originating slot should not be part of any active DMA transfer. + */ +void edma_link(unsigned from, unsigned to) +{ + if (from >= num_slots) + return; + if (to >= num_slots) + return; + edma_parm_modify(PARM_LINK_BCNTRLD, from, 0xffff0000, PARM_OFFSET(to)); +} +EXPORT_SYMBOL(edma_link); + +/** + * edma_unlink - cut link from one parameter RAM slot + * @from: parameter RAM slot originating the link + * + * The originating slot should not be part of any active DMA transfer. + * Its link is set to 0xffff. + */ +void edma_unlink(unsigned from) +{ + if (from >= num_slots) + return; + edma_parm_or(PARM_LINK_BCNTRLD, from, 0xffff); +} +EXPORT_SYMBOL(edma_unlink); + +/*-----------------------------------------------------------------------*/ + +/* Parameter RAM operations (ii) -- read/write whole parameter sets */ + +/** + * edma_write_slot - write parameter RAM data for slot + * @slot: number of parameter RAM slot being modified + * @param: data to be written into parameter RAM slot + * + * Use this to assign all parameters of a transfer at once. This + * allows more efficient setup of transfers than issuing multiple + * calls to set up those parameters in small pieces, and provides + * complete control over all transfer options. + */ +void edma_write_slot(unsigned slot, const struct edmacc_param *param) +{ + if (slot >= num_slots) + return; + memcpy_toio(edmacc_regs_base + PARM_OFFSET(slot), param, PARM_SIZE); +} +EXPORT_SYMBOL(edma_write_slot); + +/** + * edma_read_slot - read parameter RAM data from slot + * @slot: number of parameter RAM slot being copied + * @param: where to store copy of parameter RAM data + * + * Use this to read data from a parameter RAM slot, perhaps to + * save them as a template for later reuse. + */ +void edma_read_slot(unsigned slot, struct edmacc_param *param) +{ + if (slot >= num_slots) + return; + memcpy_fromio(param, edmacc_regs_base + PARM_OFFSET(slot), PARM_SIZE); +} +EXPORT_SYMBOL(edma_read_slot); + +/*-----------------------------------------------------------------------*/ + +/* Various EDMA channel control operations */ + +/** + * edma_pause - pause dma on a channel + * @channel: on which edma_start() has been called + * + * This temporarily disables EDMA hardware events on the specified channel, + * preventing them from triggering new transfers on its behalf + */ +void edma_pause(unsigned channel) +{ + if (channel < num_channels) { + unsigned int mask = (1 << (channel & 0x1f)); + + edma_shadow0_write_array(SH_EECR, channel >> 5, mask); + } +} +EXPORT_SYMBOL(edma_pause); + +/** + * edma_resume - resumes dma on a paused channel + * @channel: on which edma_pause() has been called + * + * This re-enables EDMA hardware events on the specified channel. + */ +void edma_resume(unsigned channel) +{ + if (channel < num_channels) { + unsigned int mask = (1 << (channel & 0x1f)); + + edma_shadow0_write_array(SH_EESR, channel >> 5, mask); + } +} +EXPORT_SYMBOL(edma_resume); + +/** + * edma_start - start dma on a channel + * @channel: channel being activated + * + * Channels with event associations will be triggered by their hardware + * events, and channels without such associations will be triggered by + * software. (At this writing there is no interface for using software + * triggers except with channels that don't support hardware triggers.) + * + * Returns zero on success, else negative errno. + */ +int edma_start(unsigned channel) +{ + if (channel < num_channels) { + int j = channel >> 5; + unsigned int mask = (1 << (channel & 0x1f)); + + /* EDMA channels without event association */ + if (test_bit(channel, edma_noevent)) { + pr_debug("EDMA: ESR%d %08x\n", j, + edma_shadow0_read_array(SH_ESR, j)); + edma_shadow0_write_array(SH_ESR, j, mask); + return 0; + } + + /* EDMA channel with event association */ + pr_debug("EDMA: ER%d %08x\n", j, + edma_shadow0_read_array(SH_ER, j)); + /* Clear any pending error */ + edma_write_array(EDMA_EMCR, j, mask); + /* Clear any SER */ + edma_shadow0_write_array(SH_SECR, j, mask); + edma_shadow0_write_array(SH_EESR, j, mask); + pr_debug("EDMA: EER%d %08x\n", j, + edma_shadow0_read_array(SH_EER, j)); + return 0; + } + + return -EINVAL; +} +EXPORT_SYMBOL(edma_start); + +/** + * edma_stop - stops dma on the channel passed + * @channel: channel being deactivated + * + * When @lch is a channel, any active transfer is paused and + * all pending hardware events are cleared. The current transfer + * may not be resumed, and the channel's Parameter RAM should be + * reinitialized before being reused. + */ +void edma_stop(unsigned channel) +{ + if (channel < num_channels) { + int j = channel >> 5; + unsigned int mask = (1 << (channel & 0x1f)); + + edma_shadow0_write_array(SH_EECR, j, mask); + edma_shadow0_write_array(SH_ECR, j, mask); + edma_shadow0_write_array(SH_SECR, j, mask); + edma_write_array(EDMA_EMCR, j, mask); + + pr_debug("EDMA: EER%d %08x\n", j, + edma_shadow0_read_array(SH_EER, j)); + + /* REVISIT: consider guarding against inappropriate event + * chaining by overwriting with dummy_paramset. + */ + } +} +EXPORT_SYMBOL(edma_stop); + +/****************************************************************************** + * + * It cleans ParamEntry qand bring back EDMA to initial state if media has + * been removed before EDMA has finished.It is usedful for removable media. + * Arguments: + * ch_no - channel no + * + * Return: zero on success, or corresponding error no on failure + * + * FIXME this should not be needed ... edma_stop() should suffice. + * + *****************************************************************************/ + +void edma_clean_channel(unsigned channel) +{ + if (channel < num_channels) { + int j = (channel >> 5); + unsigned int mask = 1 << (channel & 0x1f); + + pr_debug("EDMA: EMR%d %08x\n", j, + edma_read_array(EDMA_EMR, j)); + edma_shadow0_write_array(SH_ECR, j, mask); + /* Clear the corresponding EMR bits */ + edma_write_array(EDMA_EMCR, j, mask); + /* Clear any SER */ + edma_shadow0_write_array(SH_SECR, j, mask); + edma_write(EDMA_CCERRCLR, (1 << 16) | 0x3); + } +} +EXPORT_SYMBOL(edma_clean_channel); + +/* + * edma_clear_event - clear an outstanding event on the DMA channel + * Arguments: + * channel - channel number + */ +void edma_clear_event(unsigned channel) +{ + if (channel >= num_channels) + return; + if (channel < 32) + edma_write(EDMA_ECR, 1 << channel); + else + edma_write(EDMA_ECRH, 1 << (channel - 32)); +} +EXPORT_SYMBOL(edma_clear_event); + +/*-----------------------------------------------------------------------*/ + +static int __init edma_probe(struct platform_device *pdev) +{ + struct edma_soc_info *info = pdev->dev.platform_data; + int i; + int status; + const s8 *noevent; + int irq = 0, err_irq = 0; + struct resource *r; + resource_size_t len; + + if (!info) + return -ENODEV; + + r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "edma_cc"); + if (!r) + return -ENODEV; + + len = r->end - r->start + 1; + + r = request_mem_region(r->start, len, r->name); + if (!r) + return -EBUSY; + + edmacc_regs_base = ioremap(r->start, len); + if (!edmacc_regs_base) { + status = -EBUSY; + goto fail1; + } + + num_channels = min_t(unsigned, info->n_channel, EDMA_MAX_DMACH); + num_slots = min_t(unsigned, info->n_slot, EDMA_MAX_PARAMENTRY); + + dev_dbg(&pdev->dev, "DMA REG BASE ADDR=%p\n", edmacc_regs_base); + + for (i = 0; i < num_slots; i++) + memcpy_toio(edmacc_regs_base + PARM_OFFSET(i), + &dummy_paramset, PARM_SIZE); + + noevent = info->noevent; + if (noevent) { + while (*noevent != -1) + set_bit(*noevent++, edma_noevent); + } + + irq = platform_get_irq(pdev, 0); + status = request_irq(irq, dma_irq_handler, 0, "edma", &pdev->dev); + if (status < 0) { + dev_dbg(&pdev->dev, "request_irq %d failed --> %d\n", + irq, status); + goto fail; + } + + err_irq = platform_get_irq(pdev, 1); + status = request_irq(err_irq, dma_ccerr_handler, 0, + "edma_error", &pdev->dev); + if (status < 0) { + dev_dbg(&pdev->dev, "request_irq %d failed --> %d\n", + err_irq, status); + goto fail; + } + + if (tc_errs_handled) { + status = request_irq(IRQ_TCERRINT0, dma_tc0err_handler, 0, + "edma_tc0", &pdev->dev); + if (status < 0) { + dev_dbg(&pdev->dev, "request_irq %d failed --> %d\n", + IRQ_TCERRINT0, status); + return status; + } + status = request_irq(IRQ_TCERRINT, dma_tc1err_handler, 0, + "edma_tc1", &pdev->dev); + if (status < 0) { + dev_dbg(&pdev->dev, "request_irq %d --> %d\n", + IRQ_TCERRINT, status); + return status; + } + } + + /* Everything lives on transfer controller 1 until otherwise specified. + * This way, long transfers on the low priority queue + * started by the codec engine will not cause audio defects. + */ + for (i = 0; i < num_channels; i++) + map_dmach_queue(i, EVENTQ_1); + + /* Event queue to TC mapping */ + for (i = 0; queue_tc_mapping[i][0] != -1; i++) + map_queue_tc(queue_tc_mapping[i][0], queue_tc_mapping[i][1]); + + /* Event queue priority mapping */ + for (i = 0; queue_priority_mapping[i][0] != -1; i++) + assign_priority_to_queue(queue_priority_mapping[i][0], + queue_priority_mapping[i][1]); + + for (i = 0; i < info->n_region; i++) { + edma_write_array2(EDMA_DRAE, i, 0, 0x0); + edma_write_array2(EDMA_DRAE, i, 1, 0x0); + edma_write_array(EDMA_QRAE, i, 0x0); + } + + return 0; + +fail: + if (err_irq) + free_irq(err_irq, NULL); + if (irq) + free_irq(irq, NULL); + iounmap(edmacc_regs_base); +fail1: + release_mem_region(r->start, len); + return status; +} + + +static struct platform_driver edma_driver = { + .driver.name = "edma", +}; + +static int __init edma_init(void) +{ + return platform_driver_probe(&edma_driver, edma_probe); +} +arch_initcall(edma_init); + diff --git a/arch/arm/mach-davinci/gpio.c b/arch/arm/mach-davinci/gpio.c index b49e9d092aa..1aba41c6351 100644 --- a/arch/arm/mach-davinci/gpio.c +++ b/arch/arm/mach-davinci/gpio.c @@ -20,6 +20,7 @@ #include <linux/irq.h> #include <linux/bitops.h> +#include <mach/cputype.h> #include <mach/irqs.h> #include <mach/hardware.h> #include <mach/gpio.h> @@ -36,9 +37,10 @@ struct davinci_gpio { static struct davinci_gpio chips[DIV_ROUND_UP(DAVINCI_N_GPIO, 32)]; +static unsigned __initdata ngpio; /* create a non-inlined version */ -static struct gpio_controller *__iomem __init gpio2controller(unsigned gpio) +static struct gpio_controller __iomem * __init gpio2controller(unsigned gpio) { return __gpio_to_controller(gpio); } @@ -114,9 +116,30 @@ static int __init davinci_gpio_setup(void) { int i, base; - for (i = 0, base = 0; - i < ARRAY_SIZE(chips); - i++, base += 32) { + /* The gpio banks conceptually expose a segmented bitmap, + * and "ngpio" is one more than the largest zero-based + * bit index that's valid. + */ + if (cpu_is_davinci_dm355()) { /* or dm335() */ + ngpio = 104; + } else if (cpu_is_davinci_dm644x()) { /* or dm337() */ + ngpio = 71; + } else if (cpu_is_davinci_dm646x()) { + /* NOTE: each bank has several "reserved" bits, + * unusable as GPIOs. Only 33 of the GPIO numbers + * are usable, and we're not rejecting the others. + */ + ngpio = 43; + } else { + /* if cpu_is_davinci_dm643x() ngpio = 111 */ + pr_err("GPIO setup: how many GPIOs?\n"); + return -EINVAL; + } + + if (WARN_ON(DAVINCI_N_GPIO < ngpio)) + ngpio = DAVINCI_N_GPIO; + + for (i = 0, base = 0; base < ngpio; i++, base += 32) { chips[i].chip.label = "DaVinci"; chips[i].chip.direction_input = davinci_direction_in; @@ -125,7 +148,7 @@ static int __init davinci_gpio_setup(void) chips[i].chip.set = davinci_gpio_set; chips[i].chip.base = base; - chips[i].chip.ngpio = DAVINCI_N_GPIO - base; + chips[i].chip.ngpio = ngpio - base; if (chips[i].chip.ngpio > 32) chips[i].chip.ngpio = 32; @@ -143,11 +166,11 @@ pure_initcall(davinci_gpio_setup); * We expect irqs will normally be set up as input pins, but they can also be * used as output pins ... which is convenient for testing. * - * NOTE: GPIO0..GPIO7 also have direct INTC hookups, which work in addition - * to their GPIOBNK0 irq (but with a bit less overhead). But we don't have - * a good way to hook those up ... + * NOTE: The first few GPIOs also have direct INTC hookups in addition + * to their GPIOBNK0 irq, with a bit less overhead but less flexibility + * on triggering (e.g. no edge options). We don't try to use those. * - * All those INTC hookups (GPIO0..GPIO7 plus five IRQ banks) can also + * All those INTC hookups (direct, plus several IRQ banks) can also * serve as EDMA event triggers. */ @@ -235,29 +258,42 @@ gpio_irq_handler(unsigned irq, struct irq_desc *desc) } /* - * NOTE: for suspend/resume, probably best to make a sysdev (and class) - * with its suspend/resume calls hooking into the results of the set_wake() + * NOTE: for suspend/resume, probably best to make a platform_device with + * suspend_late/resume_resume calls hooking into results of the set_wake() * calls ... so if no gpios are wakeup events the clock can be disabled, * with outputs left at previously set levels, and so that VDD3P3V.IOPWDN0 - * can be set appropriately for GPIOV33 pins. + * (dm6446) can be set appropriately for GPIOV33 pins. */ static int __init davinci_gpio_irq_setup(void) { unsigned gpio, irq, bank; + unsigned bank_irq; struct clk *clk; + u32 binten = 0; + + if (cpu_is_davinci_dm355()) { /* or dm335() */ + bank_irq = IRQ_DM355_GPIOBNK0; + } else if (cpu_is_davinci_dm644x()) { + bank_irq = IRQ_GPIOBNK0; + } else if (cpu_is_davinci_dm646x()) { + bank_irq = IRQ_DM646X_GPIOBNK0; + } else { + printk(KERN_ERR "Don't know first GPIO bank IRQ.\n"); + return -EINVAL; + } clk = clk_get(NULL, "gpio"); if (IS_ERR(clk)) { printk(KERN_ERR "Error %ld getting gpio clock?\n", PTR_ERR(clk)); - return 0; + return PTR_ERR(clk); } - clk_enable(clk); - for (gpio = 0, irq = gpio_to_irq(0), bank = IRQ_GPIOBNK0; - gpio < DAVINCI_N_GPIO; bank++) { + for (gpio = 0, irq = gpio_to_irq(0), bank = 0; + gpio < ngpio; + bank++, bank_irq++) { struct gpio_controller *__iomem g = gpio2controller(gpio); unsigned i; @@ -265,28 +301,28 @@ static int __init davinci_gpio_irq_setup(void) __raw_writel(~0, &g->clr_rising); /* set up all irqs in this bank */ - set_irq_chained_handler(bank, gpio_irq_handler); - set_irq_chip_data(bank, g); - set_irq_data(bank, (void *)irq); + set_irq_chained_handler(bank_irq, gpio_irq_handler); + set_irq_chip_data(bank_irq, g); + set_irq_data(bank_irq, (void *)irq); - for (i = 0; i < 16 && gpio < DAVINCI_N_GPIO; - i++, irq++, gpio++) { + for (i = 0; i < 16 && gpio < ngpio; i++, irq++, gpio++) { set_irq_chip(irq, &gpio_irqchip); set_irq_chip_data(irq, g); set_irq_handler(irq, handle_simple_irq); set_irq_flags(irq, IRQF_VALID); } + + binten |= BIT(bank); } /* BINTEN -- per-bank interrupt enable. genirq would also let these * bits be set/cleared dynamically. */ - __raw_writel(0x1f, (void *__iomem) + __raw_writel(binten, (void *__iomem) IO_ADDRESS(DAVINCI_GPIO_BASE + 0x08)); printk(KERN_INFO "DaVinci: %d gpio irqs\n", irq - gpio_to_irq(0)); return 0; } - arch_initcall(davinci_gpio_irq_setup); diff --git a/arch/arm/mach-davinci/id.c b/arch/arm/mach-davinci/id.c index bf067d60491..018b994cd79 100644 --- a/arch/arm/mach-davinci/id.c +++ b/arch/arm/mach-davinci/id.c @@ -15,7 +15,9 @@ #include <linux/init.h> #include <linux/io.h> -#define JTAG_ID_BASE 0x01c40028 +#define JTAG_ID_BASE IO_ADDRESS(0x01c40028) + +static unsigned int davinci_revision; struct davinci_id { u8 variant; /* JTAG ID bits 31:28 */ @@ -33,6 +35,20 @@ static struct davinci_id davinci_ids[] __initdata = { .manufacturer = 0x017, .type = 0x64460000, }, + { + /* DM646X */ + .part_no = 0xb770, + .variant = 0x0, + .manufacturer = 0x017, + .type = 0x64670000, + }, + { + /* DM355 */ + .part_no = 0xb73b, + .variant = 0x0, + .manufacturer = 0x00f, + .type = 0x03550000, + }, }; /* @@ -42,7 +58,7 @@ static u16 __init davinci_get_part_no(void) { u32 dev_id, part_no; - dev_id = davinci_readl(JTAG_ID_BASE); + dev_id = __raw_readl(JTAG_ID_BASE); part_no = ((dev_id >> 12) & 0xffff); @@ -56,13 +72,19 @@ static u8 __init davinci_get_variant(void) { u32 variant; - variant = davinci_readl(JTAG_ID_BASE); + variant = __raw_readl(JTAG_ID_BASE); variant = (variant >> 28) & 0xf; return variant; } +unsigned int davinci_rev(void) +{ + return davinci_revision >> 16; +} +EXPORT_SYMBOL(davinci_rev); + void __init davinci_check_revision(void) { int i; @@ -75,7 +97,7 @@ void __init davinci_check_revision(void) /* First check only the major version in a safe way */ for (i = 0; i < ARRAY_SIZE(davinci_ids); i++) { if (part_no == (davinci_ids[i].part_no)) { - system_rev = davinci_ids[i].type; + davinci_revision = davinci_ids[i].type; break; } } @@ -84,10 +106,11 @@ void __init davinci_check_revision(void) for (i = 0; i < ARRAY_SIZE(davinci_ids); i++) { if (part_no == davinci_ids[i].part_no && variant == davinci_ids[i].variant) { - system_rev = davinci_ids[i].type; + davinci_revision = davinci_ids[i].type; break; } } - printk("DaVinci DM%04x variant 0x%x\n", system_rev >> 16, variant); + printk(KERN_INFO "DaVinci DM%04x variant 0x%x\n", + davinci_rev(), variant); } diff --git a/arch/arm/mach-davinci/include/mach/board-dm6446evm.h b/arch/arm/mach-davinci/include/mach/board-dm6446evm.h new file mode 100644 index 00000000000..3216f21c123 --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/board-dm6446evm.h @@ -0,0 +1,20 @@ +/* + * DaVinci DM6446 EVM board specific headers + * + * Author: Kevin Hilman, Deep Root Systems, LLC + * + * 2007 (c) Deep Root Systems, LLC. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or ifndef. + */ + +#ifndef _MACH_DAVINCI_DM6446EVM_H +#define _MACH_DAVINCI_DM6446EVM_H + +#include <linux/types.h> + +int dm6446evm_eeprom_read(char *buf, off_t off, size_t count); +int dm6446evm_eeprom_write(char *buf, off_t off, size_t count); + +#endif diff --git a/arch/arm/mach-davinci/include/mach/clkdev.h b/arch/arm/mach-davinci/include/mach/clkdev.h new file mode 100644 index 00000000000..730c49d1ebd --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/clkdev.h @@ -0,0 +1,13 @@ +#ifndef __MACH_CLKDEV_H +#define __MACH_CLKDEV_H + +static inline int __clk_get(struct clk *clk) +{ + return 1; +} + +static inline void __clk_put(struct clk *clk) +{ +} + +#endif diff --git a/arch/arm/mach-davinci/include/mach/clock.h b/arch/arm/mach-davinci/include/mach/clock.h index 38bdd49bc18..a3b04021987 100644 --- a/arch/arm/mach-davinci/include/mach/clock.h +++ b/arch/arm/mach-davinci/include/mach/clock.h @@ -17,6 +17,5 @@ struct clk; extern int clk_register(struct clk *clk); extern void clk_unregister(struct clk *clk); -extern int davinci_clk_init(void); #endif diff --git a/arch/arm/mach-davinci/include/mach/common.h b/arch/arm/mach-davinci/include/mach/common.h index 4b522e5c70e..19177097625 100644 --- a/arch/arm/mach-davinci/include/mach/common.h +++ b/arch/arm/mach-davinci/include/mach/common.h @@ -16,6 +16,12 @@ struct sys_timer; extern struct sys_timer davinci_timer; +extern void davinci_irq_init(void); +extern void davinci_map_common_io(void); + +/* parameters describe VBUS sourcing for host mode */ +extern void setup_usb(unsigned mA, unsigned potpgt_msec); + /* parameters describe VBUS sourcing for host mode */ extern void setup_usb(unsigned mA, unsigned potpgt_msec); diff --git a/arch/arm/mach-davinci/include/mach/cputype.h b/arch/arm/mach-davinci/include/mach/cputype.h new file mode 100644 index 00000000000..27cfb1b3a66 --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/cputype.h @@ -0,0 +1,49 @@ +/* + * DaVinci CPU type detection + * + * Author: Kevin Hilman, Deep Root Systems, LLC + * + * Defines the cpu_is_*() macros for runtime detection of DaVinci + * device type. In addtion, if support for a given device is not + * compiled in to the kernel, the macros return 0 so that + * resulting code can be optimized out. + * + * 2009 (c) Deep Root Systems, LLC. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#ifndef _ASM_ARCH_CPU_H +#define _ASM_ARCH_CPU_H + +extern unsigned int davinci_rev(void); + +#define IS_DAVINCI_CPU(type, id) \ +static inline int is_davinci_dm ##type(void) \ +{ \ + return (davinci_rev() == (id)) ? 1 : 0; \ +} + +IS_DAVINCI_CPU(644x, 0x6446) +IS_DAVINCI_CPU(646x, 0x6467) +IS_DAVINCI_CPU(355, 0x355) + +#ifdef CONFIG_ARCH_DAVINCI_DM644x +#define cpu_is_davinci_dm644x() is_davinci_dm644x() +#else +#define cpu_is_davinci_dm644x() 0 +#endif + +#ifdef CONFIG_ARCH_DAVINCI_DM646x +#define cpu_is_davinci_dm646x() is_davinci_dm646x() +#else +#define cpu_is_davinci_dm646x() 0 +#endif + +#ifdef CONFIG_ARCH_DAVINCI_DM355 +#define cpu_is_davinci_dm355() is_davinci_dm355() +#else +#define cpu_is_davinci_dm355() 0 +#endif + +#endif diff --git a/arch/arm/mach-imx/include/mach/mx1ads.h b/arch/arm/mach-davinci/include/mach/dm644x.h index def05d510eb..3dcb9f4e58b 100644 --- a/arch/arm/mach-imx/include/mach/mx1ads.h +++ b/arch/arm/mach-davinci/include/mach/dm644x.h @@ -1,7 +1,8 @@ /* - * arch/arm/mach-imx/include/mach/mx1ads.h + * This file contains the processor specific definitions + * of the TI DM644x. * - * Copyright (C) 2004 Robert Schwebel, Pengutronix + * Copyright (C) 2008 Texas Instruments. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -18,19 +19,19 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * */ +#ifndef __ASM_ARCH_DM644X_H +#define __ASM_ARCH_DM644X_H -#ifndef __ASM_ARCH_MX1ADS_H -#define __ASM_ARCH_MX1ADS_H +#include <linux/platform_device.h> +#include <mach/hardware.h> -/* ------------------------------------------------------------------------ */ -/* Memory Map for the M9328MX1ADS (MX1ADS) Board */ -/* ------------------------------------------------------------------------ */ +#define DM644X_EMAC_BASE (0x01C80000) +#define DM644X_EMAC_CNTRL_OFFSET (0x0000) +#define DM644X_EMAC_CNTRL_MOD_OFFSET (0x1000) +#define DM644X_EMAC_CNTRL_RAM_OFFSET (0x2000) +#define DM644X_EMAC_MDIO_OFFSET (0x4000) +#define DM644X_EMAC_CNTRL_RAM_SIZE (0x2000) -#define MX1ADS_FLASH_PHYS 0x10000000 -#define MX1ADS_FLASH_SIZE (16*1024*1024) +void __init dm644x_init(void); -#define IMX_FB_PHYS (0x0C000000 - 0x40000) - -#define CLK32 32000 - -#endif /* __ASM_ARCH_MX1ADS_H */ +#endif /* __ASM_ARCH_DM644X_H */ diff --git a/arch/arm/mach-davinci/include/mach/edma.h b/arch/arm/mach-davinci/include/mach/edma.h new file mode 100644 index 00000000000..f6fc5396daf --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/edma.h @@ -0,0 +1,228 @@ +/* + * TI DAVINCI dma definitions + * + * Copyright (C) 2006-2009 Texas Instruments. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +/* + * This EDMA3 programming framework exposes two basic kinds of resource: + * + * Channel Triggers transfers, usually from a hardware event but + * also manually or by "chaining" from DMA completions. + * Each channel is coupled to a Parameter RAM (PaRAM) slot. + * + * Slot Each PaRAM slot holds a DMA transfer descriptor (PaRAM + * "set"), source and destination addresses, a link to a + * next PaRAM slot (if any), options for the transfer, and + * instructions for updating those addresses. There are + * more than twice as many slots as event channels. + * + * Each PaRAM set describes a sequence of transfers, either for one large + * buffer or for several discontiguous smaller buffers. An EDMA transfer + * is driven only from a channel, which performs the transfers specified + * in its PaRAM slot until there are no more transfers. When that last + * transfer completes, the "link" field may be used to reload the channel's + * PaRAM slot with a new transfer descriptor. + * + * The EDMA Channel Controller (CC) maps requests from channels into physical + * Transfer Controller (TC) requests when the channel triggers (by hardware + * or software events, or by chaining). The two physical DMA channels provided + * by the TCs are thus shared by many logical channels. + * + * DaVinci hardware also has a "QDMA" mechanism which is not currently + * supported through this interface. (DSP firmware uses it though.) + */ + +#ifndef EDMA_H_ +#define EDMA_H_ + +/* PaRAM slots are laid out like this */ +struct edmacc_param { + unsigned int opt; + unsigned int src; + unsigned int a_b_cnt; + unsigned int dst; + unsigned int src_dst_bidx; + unsigned int link_bcntrld; + unsigned int src_dst_cidx; + unsigned int ccnt; +}; + +#define CCINT0_INTERRUPT 16 +#define CCERRINT_INTERRUPT 17 +#define TCERRINT0_INTERRUPT 18 +#define TCERRINT1_INTERRUPT 19 + +/* fields in edmacc_param.opt */ +#define SAM BIT(0) +#define DAM BIT(1) +#define SYNCDIM BIT(2) +#define STATIC BIT(3) +#define EDMA_FWID (0x07 << 8) +#define TCCMODE BIT(11) +#define EDMA_TCC(t) ((t) << 12) +#define TCINTEN BIT(20) +#define ITCINTEN BIT(21) +#define TCCHEN BIT(22) +#define ITCCHEN BIT(23) + +#define TRWORD (0x7<<2) +#define PAENTRY (0x1ff<<5) + +/* Drivers should avoid using these symbolic names for dm644x + * channels, and use platform_device IORESOURCE_DMA resources + * instead. (Other DaVinci chips have different peripherals + * and thus have different DMA channel mappings.) + */ +#define DAVINCI_DMA_MCBSP_TX 2 +#define DAVINCI_DMA_MCBSP_RX 3 +#define DAVINCI_DMA_VPSS_HIST 4 +#define DAVINCI_DMA_VPSS_H3A 5 +#define DAVINCI_DMA_VPSS_PRVU 6 +#define DAVINCI_DMA_VPSS_RSZ 7 +#define DAVINCI_DMA_IMCOP_IMXINT 8 +#define DAVINCI_DMA_IMCOP_VLCDINT 9 +#define DAVINCI_DMA_IMCO_PASQINT 10 +#define DAVINCI_DMA_IMCOP_DSQINT 11 +#define DAVINCI_DMA_SPI_SPIX 16 +#define DAVINCI_DMA_SPI_SPIR 17 +#define DAVINCI_DMA_UART0_URXEVT0 18 +#define DAVINCI_DMA_UART0_UTXEVT0 19 +#define DAVINCI_DMA_UART1_URXEVT1 20 +#define DAVINCI_DMA_UART1_UTXEVT1 21 +#define DAVINCI_DMA_UART2_URXEVT2 22 +#define DAVINCI_DMA_UART2_UTXEVT2 23 +#define DAVINCI_DMA_MEMSTK_MSEVT 24 +#define DAVINCI_DMA_MMCRXEVT 26 +#define DAVINCI_DMA_MMCTXEVT 27 +#define DAVINCI_DMA_I2C_ICREVT 28 +#define DAVINCI_DMA_I2C_ICXEVT 29 +#define DAVINCI_DMA_GPIO_GPINT0 32 +#define DAVINCI_DMA_GPIO_GPINT1 33 +#define DAVINCI_DMA_GPIO_GPINT2 34 +#define DAVINCI_DMA_GPIO_GPINT3 35 +#define DAVINCI_DMA_GPIO_GPINT4 36 +#define DAVINCI_DMA_GPIO_GPINT5 37 +#define DAVINCI_DMA_GPIO_GPINT6 38 +#define DAVINCI_DMA_GPIO_GPINT7 39 +#define DAVINCI_DMA_GPIO_GPBNKINT0 40 +#define DAVINCI_DMA_GPIO_GPBNKINT1 41 +#define DAVINCI_DMA_GPIO_GPBNKINT2 42 +#define DAVINCI_DMA_GPIO_GPBNKINT3 43 +#define DAVINCI_DMA_GPIO_GPBNKINT4 44 +#define DAVINCI_DMA_TIMER0_TINT0 48 +#define DAVINCI_DMA_TIMER1_TINT1 49 +#define DAVINCI_DMA_TIMER2_TINT2 50 +#define DAVINCI_DMA_TIMER3_TINT3 51 +#define DAVINCI_DMA_PWM0 52 +#define DAVINCI_DMA_PWM1 53 +#define DAVINCI_DMA_PWM2 54 + +/*ch_status paramater of callback function possible values*/ +#define DMA_COMPLETE 1 +#define DMA_CC_ERROR 2 +#define DMA_TC1_ERROR 3 +#define DMA_TC2_ERROR 4 + +enum address_mode { + INCR = 0, + FIFO = 1 +}; + +enum fifo_width { + W8BIT = 0, + W16BIT = 1, + W32BIT = 2, + W64BIT = 3, + W128BIT = 4, + W256BIT = 5 +}; + +enum dma_event_q { + EVENTQ_0 = 0, + EVENTQ_1 = 1, + EVENTQ_DEFAULT = -1 +}; + +enum sync_dimension { + ASYNC = 0, + ABSYNC = 1 +}; + +#define EDMA_CHANNEL_ANY -1 /* for edma_alloc_channel() */ +#define EDMA_SLOT_ANY -1 /* for edma_alloc_slot() */ + +/* alloc/free DMA channels and their dedicated parameter RAM slots */ +int edma_alloc_channel(int channel, + void (*callback)(unsigned channel, u16 ch_status, void *data), + void *data, enum dma_event_q); +void edma_free_channel(unsigned channel); + +/* alloc/free parameter RAM slots */ +int edma_alloc_slot(int slot); +void edma_free_slot(unsigned slot); + +/* calls that operate on part of a parameter RAM slot */ +void edma_set_src(unsigned slot, dma_addr_t src_port, + enum address_mode mode, enum fifo_width); +void edma_set_dest(unsigned slot, dma_addr_t dest_port, + enum address_mode mode, enum fifo_width); +void edma_get_position(unsigned slot, dma_addr_t *src, dma_addr_t *dst); +void edma_set_src_index(unsigned slot, s16 src_bidx, s16 src_cidx); +void edma_set_dest_index(unsigned slot, s16 dest_bidx, s16 dest_cidx); +void edma_set_transfer_params(unsigned slot, u16 acnt, u16 bcnt, u16 ccnt, + u16 bcnt_rld, enum sync_dimension sync_mode); +void edma_link(unsigned from, unsigned to); +void edma_unlink(unsigned from); + +/* calls that operate on an entire parameter RAM slot */ +void edma_write_slot(unsigned slot, const struct edmacc_param *params); +void edma_read_slot(unsigned slot, struct edmacc_param *params); + +/* channel control operations */ +int edma_start(unsigned channel); +void edma_stop(unsigned channel); +void edma_clean_channel(unsigned channel); +void edma_clear_event(unsigned channel); +void edma_pause(unsigned channel); +void edma_resume(unsigned channel); + +/* UNRELATED TO DMA */ +int davinci_alloc_iram(unsigned size); +void davinci_free_iram(unsigned addr, unsigned size); + +/* platform_data for EDMA driver */ +struct edma_soc_info { + + /* how many dma resources of each type */ + unsigned n_channel; + unsigned n_region; + unsigned n_slot; + unsigned n_tc; + + /* list of channels with no even trigger; terminated by "-1" */ + const s8 *noevent; +}; + +#endif diff --git a/arch/arm/mach-davinci/include/mach/gpio.h b/arch/arm/mach-davinci/include/mach/gpio.h index b456f079f43..efe3281364e 100644 --- a/arch/arm/mach-davinci/include/mach/gpio.h +++ b/arch/arm/mach-davinci/include/mach/gpio.h @@ -15,9 +15,11 @@ #include <linux/io.h> #include <asm-generic/gpio.h> -#include <mach/hardware.h> + #include <mach/irqs.h> +#define DAVINCI_GPIO_BASE 0x01C67000 + /* * basic gpio routines * @@ -26,23 +28,18 @@ * go through boot loaders. * * the gpio clock will be turned on when gpios are used, and you may also - * need to pay attention to PINMUX0 and PINMUX1 to be sure those pins are + * need to pay attention to PINMUX registers to be sure those pins are * used as gpios, not with other peripherals. * * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1). For documentation, - * and maybe for later updates, code should write GPIO(N) or: - * - GPIOV18(N) for 1.8V pins, N in 0..53; same as GPIO(0)..GPIO(53) - * - GPIOV33(N) for 3.3V pins, N in 0..17; same as GPIO(54)..GPIO(70) - * - * For GPIO IRQs use gpio_to_irq(GPIO(N)) or gpio_to_irq(GPIOV33(N)) etc - * for now, that's != GPIO(N) + * and maybe for later updates, code may write GPIO(N). These may be + * all 1.8V signals, all 3.3V ones, or a mix of the two. A given chip + * may not support all the GPIOs in that range. * * GPIOs can also be on external chips, numbered after the ones built-in * to the DaVinci chip. For now, they won't be usable as IRQ sources. */ -#define GPIO(X) (X) /* 0 <= X <= 70 */ -#define GPIOV18(X) (X) /* 1.8V i/o; 0 <= X <= 53 */ -#define GPIOV33(X) ((X)+54) /* 3.3V i/o; 0 <= X <= 17 */ +#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */ struct gpio_controller { u32 dir; @@ -71,12 +68,14 @@ __gpio_to_controller(unsigned gpio) { void *__iomem ptr; - if (gpio < 32) + if (gpio < 32 * 1) ptr = IO_ADDRESS(DAVINCI_GPIO_BASE + 0x10); - else if (gpio < 64) + else if (gpio < 32 * 2) ptr = IO_ADDRESS(DAVINCI_GPIO_BASE + 0x38); - else if (gpio < DAVINCI_N_GPIO) + else if (gpio < 32 * 3) ptr = IO_ADDRESS(DAVINCI_GPIO_BASE + 0x60); + else if (gpio < 32 * 4) + ptr = IO_ADDRESS(DAVINCI_GPIO_BASE + 0x88); else ptr = NULL; return ptr; diff --git a/arch/arm/mach-davinci/include/mach/hardware.h b/arch/arm/mach-davinci/include/mach/hardware.h index a2e8969afac..48c77934d51 100644 --- a/arch/arm/mach-davinci/include/mach/hardware.h +++ b/arch/arm/mach-davinci/include/mach/hardware.h @@ -1,9 +1,9 @@ /* - * Common hardware definitions + * Hardware definitions common to all DaVinci family processors * - * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com> + * Author: Kevin Hilman, Deep Root Systems, LLC * - * 2007 (c) MontaVista Software, Inc. This file is licensed under + * 2007 (c) Deep Root Systems, LLC. This file is licensed under * the terms of the GNU General Public License version 2. This program * is licensed "as is" without any warranty of any kind, whether express * or implied. @@ -12,41 +12,16 @@ #define __ASM_ARCH_HARDWARE_H /* - * Base register addresses + * Before you add anything to ths file: + * + * This header is for defines common to ALL DaVinci family chips. + * Anything that is chip specific should go in <chipname>.h, + * and the chip/board init code should then explicitly include + * <chipname>.h */ -#define DAVINCI_DMA_3PCC_BASE (0x01C00000) -#define DAVINCI_DMA_3PTC0_BASE (0x01C10000) -#define DAVINCI_DMA_3PTC1_BASE (0x01C10400) -#define DAVINCI_I2C_BASE (0x01C21000) -#define DAVINCI_PWM0_BASE (0x01C22000) -#define DAVINCI_PWM1_BASE (0x01C22400) -#define DAVINCI_PWM2_BASE (0x01C22800) -#define DAVINCI_SYSTEM_MODULE_BASE (0x01C40000) -#define DAVINCI_PLL_CNTRL0_BASE (0x01C40800) -#define DAVINCI_PLL_CNTRL1_BASE (0x01C40C00) -#define DAVINCI_PWR_SLEEP_CNTRL_BASE (0x01C41000) -#define DAVINCI_SYSTEM_DFT_BASE (0x01C42000) -#define DAVINCI_IEEE1394_BASE (0x01C60000) -#define DAVINCI_USB_OTG_BASE (0x01C64000) -#define DAVINCI_CFC_ATA_BASE (0x01C66000) -#define DAVINCI_SPI_BASE (0x01C66800) -#define DAVINCI_GPIO_BASE (0x01C67000) -#define DAVINCI_UHPI_BASE (0x01C67800) -#define DAVINCI_VPSS_REGS_BASE (0x01C70000) -#define DAVINCI_EMAC_CNTRL_REGS_BASE (0x01C80000) -#define DAVINCI_EMAC_WRAPPER_CNTRL_REGS_BASE (0x01C81000) -#define DAVINCI_EMAC_WRAPPER_RAM_BASE (0x01C82000) -#define DAVINCI_MDIO_CNTRL_REGS_BASE (0x01C84000) -#define DAVINCI_IMCOP_BASE (0x01CC0000) -#define DAVINCI_ASYNC_EMIF_CNTRL_BASE (0x01E00000) -#define DAVINCI_VLYNQ_BASE (0x01E01000) -#define DAVINCI_MCBSP_BASE (0x01E02000) -#define DAVINCI_MMC_SD_BASE (0x01E10000) -#define DAVINCI_MS_BASE (0x01E20000) -#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE (0x02000000) -#define DAVINCI_ASYNC_EMIF_DATA_CE1_BASE (0x04000000) -#define DAVINCI_ASYNC_EMIF_DATA_CE2_BASE (0x06000000) -#define DAVINCI_ASYNC_EMIF_DATA_CE3_BASE (0x08000000) -#define DAVINCI_VLYNQ_REMOTE_BASE (0x0C000000) +#define DAVINCI_SYSTEM_MODULE_BASE 0x01C40000 + +/* System control register offsets */ +#define DM64XX_VDD3P3V_PWDN 0x48 #endif /* __ASM_ARCH_HARDWARE_H */ diff --git a/arch/arm/mach-davinci/include/mach/io.h b/arch/arm/mach-davinci/include/mach/io.h index a48795fd241..2479785405a 100644 --- a/arch/arm/mach-davinci/include/mach/io.h +++ b/arch/arm/mach-davinci/include/mach/io.h @@ -40,22 +40,12 @@ #else #define IOMEM(x) ((void __force __iomem *)(x)) -/* - * Functions to access the DaVinci IO region - * - * NOTE: - Use davinci_read/write[bwl] for physical register addresses - * - Use __raw_read/write[bwl]() for virtual register addresses - * - Use IO_ADDRESS(phys_addr) to convert registers to virtual addresses - * - DO NOT use hardcoded virtual addresses to allow changing the - * IO address space again if needed - */ -#define davinci_readb(a) __raw_readb(IO_ADDRESS(a)) -#define davinci_readw(a) __raw_readw(IO_ADDRESS(a)) -#define davinci_readl(a) __raw_readl(IO_ADDRESS(a)) +#define __arch_ioremap(p, s, t) davinci_ioremap(p, s, t) +#define __arch_iounmap(v) davinci_iounmap(v) -#define davinci_writeb(v, a) __raw_writeb(v, IO_ADDRESS(a)) -#define davinci_writew(v, a) __raw_writew(v, IO_ADDRESS(a)) -#define davinci_writel(v, a) __raw_writel(v, IO_ADDRESS(a)) +void __iomem *davinci_ioremap(unsigned long phys, size_t size, + unsigned int type); +void davinci_iounmap(volatile void __iomem *addr); #endif /* __ASSEMBLER__ */ #endif /* __ASM_ARCH_IO_H */ diff --git a/arch/arm/mach-davinci/include/mach/irqs.h b/arch/arm/mach-davinci/include/mach/irqs.h index f4c5ca6da9f..18066074c99 100644 --- a/arch/arm/mach-davinci/include/mach/irqs.h +++ b/arch/arm/mach-davinci/include/mach/irqs.h @@ -96,10 +96,111 @@ #define IRQ_EMUINT 63 #define DAVINCI_N_AINTC_IRQ 64 -#define DAVINCI_N_GPIO 71 +#define DAVINCI_N_GPIO 104 #define NR_IRQS (DAVINCI_N_AINTC_IRQ + DAVINCI_N_GPIO) #define ARCH_TIMER_IRQ IRQ_TINT1_TINT34 +/* DaVinci DM6467-specific Interrupts */ +#define IRQ_DM646X_VP_VERTINT0 0 +#define IRQ_DM646X_VP_VERTINT1 1 +#define IRQ_DM646X_VP_VERTINT2 2 +#define IRQ_DM646X_VP_VERTINT3 3 +#define IRQ_DM646X_VP_ERRINT 4 +#define IRQ_DM646X_RESERVED_1 5 +#define IRQ_DM646X_RESERVED_2 6 +#define IRQ_DM646X_WDINT 7 +#define IRQ_DM646X_CRGENINT0 8 +#define IRQ_DM646X_CRGENINT1 9 +#define IRQ_DM646X_TSIFINT0 10 +#define IRQ_DM646X_TSIFINT1 11 +#define IRQ_DM646X_VDCEINT 12 +#define IRQ_DM646X_USBINT 13 +#define IRQ_DM646X_USBDMAINT 14 +#define IRQ_DM646X_PCIINT 15 +#define IRQ_DM646X_TCERRINT2 20 +#define IRQ_DM646X_TCERRINT3 21 +#define IRQ_DM646X_IDE 22 +#define IRQ_DM646X_HPIINT 23 +#define IRQ_DM646X_EMACRXTHINT 24 +#define IRQ_DM646X_EMACRXINT 25 +#define IRQ_DM646X_EMACTXINT 26 +#define IRQ_DM646X_EMACMISCINT 27 +#define IRQ_DM646X_MCASP0TXINT 28 +#define IRQ_DM646X_MCASP0RXINT 29 +#define IRQ_DM646X_RESERVED_3 31 +#define IRQ_DM646X_MCASP1TXINT 32 +#define IRQ_DM646X_VLQINT 38 +#define IRQ_DM646X_UARTINT2 42 +#define IRQ_DM646X_SPINT0 43 +#define IRQ_DM646X_SPINT1 44 +#define IRQ_DM646X_DSP2ARMINT 45 +#define IRQ_DM646X_RESERVED_4 46 +#define IRQ_DM646X_PSCINT 47 +#define IRQ_DM646X_GPIO0 48 +#define IRQ_DM646X_GPIO1 49 +#define IRQ_DM646X_GPIO2 50 +#define IRQ_DM646X_GPIO3 51 +#define IRQ_DM646X_GPIO4 52 +#define IRQ_DM646X_GPIO5 53 +#define IRQ_DM646X_GPIO6 54 +#define IRQ_DM646X_GPIO7 55 +#define IRQ_DM646X_GPIOBNK0 56 +#define IRQ_DM646X_GPIOBNK1 57 +#define IRQ_DM646X_GPIOBNK2 58 +#define IRQ_DM646X_DDRINT 59 +#define IRQ_DM646X_AEMIFINT 60 + +/* DaVinci DM355-specific Interrupts */ +#define IRQ_DM355_CCDC_VDINT0 0 +#define IRQ_DM355_CCDC_VDINT1 1 +#define IRQ_DM355_CCDC_VDINT2 2 +#define IRQ_DM355_IPIPE_HST 3 +#define IRQ_DM355_H3AINT 4 +#define IRQ_DM355_IPIPE_SDR 5 +#define IRQ_DM355_IPIPEIFINT 6 +#define IRQ_DM355_OSDINT 7 +#define IRQ_DM355_VENCINT 8 +#define IRQ_DM355_IMCOPINT 11 +#define IRQ_DM355_RTOINT 13 +#define IRQ_DM355_TINT4 13 +#define IRQ_DM355_TINT2_TINT12 13 +#define IRQ_DM355_UARTINT2 14 +#define IRQ_DM355_TINT5 14 +#define IRQ_DM355_TINT2_TINT34 14 +#define IRQ_DM355_TINT6 15 +#define IRQ_DM355_TINT3_TINT12 15 +#define IRQ_DM355_SPINT1_0 17 +#define IRQ_DM355_SPINT1_1 18 +#define IRQ_DM355_SPINT2_0 19 +#define IRQ_DM355_SPINT2_1 21 +#define IRQ_DM355_TINT7 22 +#define IRQ_DM355_TINT3_TINT34 22 +#define IRQ_DM355_SDIOINT0 23 +#define IRQ_DM355_MMCINT0 26 +#define IRQ_DM355_MSINT 26 +#define IRQ_DM355_MMCINT1 27 +#define IRQ_DM355_PWMINT3 28 +#define IRQ_DM355_SDIOINT1 31 +#define IRQ_DM355_SPINT0_0 42 +#define IRQ_DM355_SPINT0_1 43 +#define IRQ_DM355_GPIO0 44 +#define IRQ_DM355_GPIO1 45 +#define IRQ_DM355_GPIO2 46 +#define IRQ_DM355_GPIO3 47 +#define IRQ_DM355_GPIO4 48 +#define IRQ_DM355_GPIO5 49 +#define IRQ_DM355_GPIO6 50 +#define IRQ_DM355_GPIO7 51 +#define IRQ_DM355_GPIO8 52 +#define IRQ_DM355_GPIO9 53 +#define IRQ_DM355_GPIOBNK0 54 +#define IRQ_DM355_GPIOBNK1 55 +#define IRQ_DM355_GPIOBNK2 56 +#define IRQ_DM355_GPIOBNK3 57 +#define IRQ_DM355_GPIOBNK4 58 +#define IRQ_DM355_GPIOBNK5 59 +#define IRQ_DM355_GPIOBNK6 60 + #endif /* __ASM_ARCH_IRQS_H */ diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h index c24b6782804..bae22cb3e27 100644 --- a/arch/arm/mach-davinci/include/mach/mux.h +++ b/arch/arm/mach-davinci/include/mach/mux.h @@ -1,55 +1,183 @@ /* - * DaVinci pin multiplexing defines + * Table of the DAVINCI register configurations for the PINMUX combinations * * Author: Vladimir Barinov, MontaVista Software, Inc. <source@mvista.com> * + * Based on linux/include/asm-arm/arch-omap/mux.h: + * Copyright (C) 2003 - 2005 Nokia Corporation + * + * Written by Tony Lindgren + * * 2007 (c) MontaVista Software, Inc. This file is licensed under * the terms of the GNU General Public License version 2. This program * is licensed "as is" without any warranty of any kind, whether express * or implied. + * + * Copyright (C) 2008 Texas Instruments. */ -#ifndef __ASM_ARCH_MUX_H -#define __ASM_ARCH_MUX_H - -#define DAVINCI_MUX_AEAW0 0 -#define DAVINCI_MUX_AEAW1 1 -#define DAVINCI_MUX_AEAW2 2 -#define DAVINCI_MUX_AEAW3 3 -#define DAVINCI_MUX_AEAW4 4 -#define DAVINCI_MUX_AECS4 10 -#define DAVINCI_MUX_AECS5 11 -#define DAVINCI_MUX_VLYNQWD0 12 -#define DAVINCI_MUX_VLYNQWD1 13 -#define DAVINCI_MUX_VLSCREN 14 -#define DAVINCI_MUX_VLYNQEN 15 -#define DAVINCI_MUX_HDIREN 16 -#define DAVINCI_MUX_ATAEN 17 -#define DAVINCI_MUX_RGB666 22 -#define DAVINCI_MUX_RGB888 23 -#define DAVINCI_MUX_LOEEN 24 -#define DAVINCI_MUX_LFLDEN 25 -#define DAVINCI_MUX_CWEN 26 -#define DAVINCI_MUX_CFLDEN 27 -#define DAVINCI_MUX_HPIEN 29 -#define DAVINCI_MUX_1394EN 30 -#define DAVINCI_MUX_EMACEN 31 - -#define DAVINCI_MUX_LEVEL2 32 -#define DAVINCI_MUX_UART0 (DAVINCI_MUX_LEVEL2 + 0) -#define DAVINCI_MUX_UART1 (DAVINCI_MUX_LEVEL2 + 1) -#define DAVINCI_MUX_UART2 (DAVINCI_MUX_LEVEL2 + 2) -#define DAVINCI_MUX_U2FLO (DAVINCI_MUX_LEVEL2 + 3) -#define DAVINCI_MUX_PWM0 (DAVINCI_MUX_LEVEL2 + 4) -#define DAVINCI_MUX_PWM1 (DAVINCI_MUX_LEVEL2 + 5) -#define DAVINCI_MUX_PWM2 (DAVINCI_MUX_LEVEL2 + 6) -#define DAVINCI_MUX_I2C (DAVINCI_MUX_LEVEL2 + 7) -#define DAVINCI_MUX_SPI (DAVINCI_MUX_LEVEL2 + 8) -#define DAVINCI_MUX_MSTK (DAVINCI_MUX_LEVEL2 + 9) -#define DAVINCI_MUX_ASP (DAVINCI_MUX_LEVEL2 + 10) -#define DAVINCI_MUX_CLK0 (DAVINCI_MUX_LEVEL2 + 16) -#define DAVINCI_MUX_CLK1 (DAVINCI_MUX_LEVEL2 + 17) -#define DAVINCI_MUX_TIMIN (DAVINCI_MUX_LEVEL2 + 18) - -extern void davinci_mux_peripheral(unsigned int mux, unsigned int enable); - -#endif /* __ASM_ARCH_MUX_H */ + +#ifndef __INC_MACH_MUX_H +#define __INC_MACH_MUX_H + +/* System module registers */ +#define PINMUX0 0x00 +#define PINMUX1 0x04 +/* dm355 only */ +#define PINMUX2 0x08 +#define PINMUX3 0x0c +#define PINMUX4 0x10 +#define INTMUX 0x18 +#define EVTMUX 0x1c + +struct mux_config { + const char *name; + const char *mux_reg_name; + const unsigned char mux_reg; + const unsigned char mask_offset; + const unsigned char mask; + const unsigned char mode; + bool debug; +}; + +enum davinci_dm644x_index { + /* ATA and HDDIR functions */ + DM644X_HDIREN, + DM644X_ATAEN, + DM644X_ATAEN_DISABLE, + + /* HPI functions */ + DM644X_HPIEN_DISABLE, + + /* AEAW functions */ + DM644X_AEAW, + + /* Memory Stick */ + DM644X_MSTK, + + /* I2C */ + DM644X_I2C, + + /* ASP function */ + DM644X_MCBSP, + + /* UART1 */ + DM644X_UART1, + + /* UART2 */ + DM644X_UART2, + + /* PWM0 */ + DM644X_PWM0, + + /* PWM1 */ + DM644X_PWM1, + + /* PWM2 */ + DM644X_PWM2, + + /* VLYNQ function */ + DM644X_VLYNQEN, + DM644X_VLSCREN, + DM644X_VLYNQWD, + + /* EMAC and MDIO function */ + DM644X_EMACEN, + + /* GPIO3V[0:16] pins */ + DM644X_GPIO3V, + + /* GPIO pins */ + DM644X_GPIO0, + DM644X_GPIO3, + DM644X_GPIO43_44, + DM644X_GPIO46_47, + + /* VPBE */ + DM644X_RGB666, + + /* LCD */ + DM644X_LOEEN, + DM644X_LFLDEN, +}; + +enum davinci_dm646x_index { + /* ATA function */ + DM646X_ATAEN, + + /* AUDIO Clock */ + DM646X_AUDCK1, + DM646X_AUDCK0, + + /* CRGEN Control */ + DM646X_CRGMUX, + + /* VPIF Control */ + DM646X_STSOMUX_DISABLE, + DM646X_STSIMUX_DISABLE, + DM646X_PTSOMUX_DISABLE, + DM646X_PTSIMUX_DISABLE, + + /* TSIF Control */ + DM646X_STSOMUX, + DM646X_STSIMUX, + DM646X_PTSOMUX_PARALLEL, + DM646X_PTSIMUX_PARALLEL, + DM646X_PTSOMUX_SERIAL, + DM646X_PTSIMUX_SERIAL, +}; + +enum davinci_dm355_index { + /* MMC/SD 0 */ + DM355_MMCSD0, + + /* MMC/SD 1 */ + DM355_SD1_CLK, + DM355_SD1_CMD, + DM355_SD1_DATA3, + DM355_SD1_DATA2, + DM355_SD1_DATA1, + DM355_SD1_DATA0, + + /* I2C */ + DM355_I2C_SDA, + DM355_I2C_SCL, + + /* ASP0 function */ + DM355_MCBSP0_BDX, + DM355_MCBSP0_X, + DM355_MCBSP0_BFSX, + DM355_MCBSP0_BDR, + DM355_MCBSP0_R, + DM355_MCBSP0_BFSR, + + /* SPI0 */ + DM355_SPI0_SDI, + DM355_SPI0_SDENA0, + DM355_SPI0_SDENA1, + + /* IRQ muxing */ + DM355_INT_EDMA_CC, + DM355_INT_EDMA_TC0_ERR, + DM355_INT_EDMA_TC1_ERR, + + /* EDMA event muxing */ + DM355_EVT8_ASP1_TX, + DM355_EVT9_ASP1_RX, + DM355_EVT26_MMC0_RX, +}; + +#ifdef CONFIG_DAVINCI_MUX +/* setup pin muxing */ +extern void davinci_mux_init(void); +extern int davinci_mux_register(const struct mux_config *pins, + unsigned long size); +extern int davinci_cfg_reg(unsigned long reg_cfg); +#else +/* boot loader does it all (no warnings from CONFIG_DAVINCI_MUX_WARNINGS) */ +static inline void davinci_mux_init(void) {} +static inline int davinci_mux_register(const struct mux_config *pins, + unsigned long size) { return 0; } +static inline int davinci_cfg_reg(unsigned long reg_cfg) { return 0; } +#endif + +#endif /* __INC_MACH_MUX_H */ diff --git a/arch/arm/mach-davinci/include/mach/psc.h b/arch/arm/mach-davinci/include/mach/psc.h index 4977aa071e1..55a90d419fa 100644 --- a/arch/arm/mach-davinci/include/mach/psc.h +++ b/arch/arm/mach-davinci/include/mach/psc.h @@ -38,8 +38,6 @@ #define DAVINCI_LPSC_TPTC1 4 #define DAVINCI_LPSC_EMAC 5 #define DAVINCI_LPSC_EMAC_WRAPPER 6 -#define DAVINCI_LPSC_MDIO 7 -#define DAVINCI_LPSC_IEEE1394 8 #define DAVINCI_LPSC_USB 9 #define DAVINCI_LPSC_ATA 10 #define DAVINCI_LPSC_VLYNQ 11 @@ -47,7 +45,6 @@ #define DAVINCI_LPSC_DDR_EMIF 13 #define DAVINCI_LPSC_AEMIF 14 #define DAVINCI_LPSC_MMC_SD 15 -#define DAVINCI_LPSC_MEMSTICK 16 #define DAVINCI_LPSC_McBSP 17 #define DAVINCI_LPSC_I2C 18 #define DAVINCI_LPSC_UART0 19 @@ -73,4 +70,54 @@ #define DAVINCI_LPSC_GEM 39 #define DAVINCI_LPSC_IMCOP 40 +#define DM355_LPSC_TIMER3 5 +#define DM355_LPSC_SPI1 6 +#define DM355_LPSC_MMC_SD1 7 +#define DM355_LPSC_McBSP1 8 +#define DM355_LPSC_PWM3 10 +#define DM355_LPSC_SPI2 11 +#define DM355_LPSC_RTO 12 +#define DM355_LPSC_VPSS_DAC 41 + +/* + * LPSC Assignments + */ +#define DM646X_LPSC_ARM 0 +#define DM646X_LPSC_C64X_CPU 1 +#define DM646X_LPSC_HDVICP0 2 +#define DM646X_LPSC_HDVICP1 3 +#define DM646X_LPSC_TPCC 4 +#define DM646X_LPSC_TPTC0 5 +#define DM646X_LPSC_TPTC1 6 +#define DM646X_LPSC_TPTC2 7 +#define DM646X_LPSC_TPTC3 8 +#define DM646X_LPSC_PCI 13 +#define DM646X_LPSC_EMAC 14 +#define DM646X_LPSC_VDCE 15 +#define DM646X_LPSC_VPSSMSTR 16 +#define DM646X_LPSC_VPSSSLV 17 +#define DM646X_LPSC_TSIF0 18 +#define DM646X_LPSC_TSIF1 19 +#define DM646X_LPSC_DDR_EMIF 20 +#define DM646X_LPSC_AEMIF 21 +#define DM646X_LPSC_McASP0 22 +#define DM646X_LPSC_McASP1 23 +#define DM646X_LPSC_CRGEN0 24 +#define DM646X_LPSC_CRGEN1 25 +#define DM646X_LPSC_UART0 26 +#define DM646X_LPSC_UART1 27 +#define DM646X_LPSC_UART2 28 +#define DM646X_LPSC_PWM0 29 +#define DM646X_LPSC_PWM1 30 +#define DM646X_LPSC_I2C 31 +#define DM646X_LPSC_SPI 32 +#define DM646X_LPSC_GPIO 33 +#define DM646X_LPSC_TIMER0 34 +#define DM646X_LPSC_TIMER1 35 +#define DM646X_LPSC_ARM_INTC 45 + +extern int davinci_psc_is_clk_active(unsigned int id); +extern void davinci_psc_config(unsigned int domain, unsigned int id, + char enable); + #endif /* __ASM_ARCH_PSC_H */ diff --git a/arch/arm/mach-davinci/include/mach/serial.h b/arch/arm/mach-davinci/include/mach/serial.h index fb8cb229bfd..632847d74a1 100644 --- a/arch/arm/mach-davinci/include/mach/serial.h +++ b/arch/arm/mach-davinci/include/mach/serial.h @@ -13,8 +13,23 @@ #include <mach/io.h> -#define DAVINCI_UART0_BASE (IO_PHYS + 0x20000) -#define DAVINCI_UART1_BASE (IO_PHYS + 0x20400) -#define DAVINCI_UART2_BASE (IO_PHYS + 0x20800) +#define DAVINCI_MAX_NR_UARTS 3 +#define DAVINCI_UART0_BASE (IO_PHYS + 0x20000) +#define DAVINCI_UART1_BASE (IO_PHYS + 0x20400) +#define DAVINCI_UART2_BASE (IO_PHYS + 0x20800) + +#define DM355_UART2_BASE (IO_PHYS + 0x206000) + +/* DaVinci UART register offsets */ +#define UART_DAVINCI_PWREMU 0x0c +#define UART_DM646X_SCR 0x10 +#define UART_DM646X_SCR_TX_WATERMARK 0x08 + +struct davinci_uart_config { + /* Bit field of UARTs present; bit 0 --> UART1 */ + unsigned int enabled_uarts; +}; + +extern void davinci_serial_init(struct davinci_uart_config *); #endif /* __ASM_ARCH_SERIAL_H */ diff --git a/arch/arm/mach-davinci/io.c b/arch/arm/mach-davinci/io.c index 299515f70b8..a548abb513e 100644 --- a/arch/arm/mach-davinci/io.c +++ b/arch/arm/mach-davinci/io.c @@ -51,7 +51,26 @@ void __init davinci_map_common_io(void) davinci_check_revision(); } -void __init davinci_init_common_hw(void) +#define BETWEEN(p, st, sz) ((p) >= (st) && (p) < ((st) + (sz))) +#define XLATE(p, pst, vst) ((void __iomem *)((p) - (pst) + (vst))) + +/* + * Intercept ioremap() requests for addresses in our fixed mapping regions. + */ +void __iomem *davinci_ioremap(unsigned long p, size_t size, unsigned int type) +{ + if (BETWEEN(p, IO_PHYS, IO_SIZE)) + return XLATE(p, IO_PHYS, IO_VIRT); + + return __arm_ioremap(p, size, type); +} +EXPORT_SYMBOL(davinci_ioremap); + +void davinci_iounmap(volatile void __iomem *addr) { - davinci_clk_init(); + unsigned long virt = (unsigned long)addr; + + if (virt >= VMALLOC_START && virt < VMALLOC_END) + __iounmap(addr); } +EXPORT_SYMBOL(davinci_iounmap); diff --git a/arch/arm/mach-davinci/irq.c b/arch/arm/mach-davinci/irq.c index 38021af8359..5a324c90e29 100644 --- a/arch/arm/mach-davinci/irq.c +++ b/arch/arm/mach-davinci/irq.c @@ -25,6 +25,7 @@ #include <linux/io.h> #include <mach/hardware.h> +#include <mach/cputype.h> #include <asm/mach/irq.h> #define IRQ_BIT(irq) ((irq) & 0x1f) @@ -40,14 +41,18 @@ #define IRQ_INTPRI0_REG_OFFSET 0x0030 #define IRQ_INTPRI7_REG_OFFSET 0x004C +const u8 *davinci_def_priorities; + +#define INTC_BASE IO_ADDRESS(DAVINCI_ARM_INTC_BASE) + static inline unsigned int davinci_irq_readl(int offset) { - return davinci_readl(DAVINCI_ARM_INTC_BASE + offset); + return __raw_readl(INTC_BASE + offset); } static inline void davinci_irq_writel(unsigned long value, int offset) { - davinci_writel(value, DAVINCI_ARM_INTC_BASE + offset); + __raw_writel(value, INTC_BASE + offset); } /* Disable interrupt */ @@ -108,9 +113,8 @@ static struct irq_chip davinci_irq_chip_0 = { .unmask = davinci_unmask_irq, }; - /* FIQ are pri 0-1; otherwise 2-7, with 7 lowest priority */ -static const u8 default_priorities[DAVINCI_N_AINTC_IRQ] __initdata = { +static const u8 dm644x_default_priorities[DAVINCI_N_AINTC_IRQ] __initdata = { [IRQ_VDINT0] = 2, [IRQ_VDINT1] = 6, [IRQ_VDINT2] = 6, @@ -177,11 +181,149 @@ static const u8 default_priorities[DAVINCI_N_AINTC_IRQ] __initdata = { [IRQ_EMUINT] = 7, }; +static const u8 dm646x_default_priorities[DAVINCI_N_AINTC_IRQ] = { + [IRQ_DM646X_VP_VERTINT0] = 7, + [IRQ_DM646X_VP_VERTINT1] = 7, + [IRQ_DM646X_VP_VERTINT2] = 7, + [IRQ_DM646X_VP_VERTINT3] = 7, + [IRQ_DM646X_VP_ERRINT] = 7, + [IRQ_DM646X_RESERVED_1] = 7, + [IRQ_DM646X_RESERVED_2] = 7, + [IRQ_DM646X_WDINT] = 7, + [IRQ_DM646X_CRGENINT0] = 7, + [IRQ_DM646X_CRGENINT1] = 7, + [IRQ_DM646X_TSIFINT0] = 7, + [IRQ_DM646X_TSIFINT1] = 7, + [IRQ_DM646X_VDCEINT] = 7, + [IRQ_DM646X_USBINT] = 7, + [IRQ_DM646X_USBDMAINT] = 7, + [IRQ_DM646X_PCIINT] = 7, + [IRQ_CCINT0] = 7, /* dma */ + [IRQ_CCERRINT] = 7, /* dma */ + [IRQ_TCERRINT0] = 7, /* dma */ + [IRQ_TCERRINT] = 7, /* dma */ + [IRQ_DM646X_TCERRINT2] = 7, + [IRQ_DM646X_TCERRINT3] = 7, + [IRQ_DM646X_IDE] = 7, + [IRQ_DM646X_HPIINT] = 7, + [IRQ_DM646X_EMACRXTHINT] = 7, + [IRQ_DM646X_EMACRXINT] = 7, + [IRQ_DM646X_EMACTXINT] = 7, + [IRQ_DM646X_EMACMISCINT] = 7, + [IRQ_DM646X_MCASP0TXINT] = 7, + [IRQ_DM646X_MCASP0RXINT] = 7, + [IRQ_AEMIFINT] = 7, + [IRQ_DM646X_RESERVED_3] = 7, + [IRQ_DM646X_MCASP1TXINT] = 7, /* clockevent */ + [IRQ_TINT0_TINT34] = 7, /* clocksource */ + [IRQ_TINT1_TINT12] = 7, /* DSP timer */ + [IRQ_TINT1_TINT34] = 7, /* system tick */ + [IRQ_PWMINT0] = 7, + [IRQ_PWMINT1] = 7, + [IRQ_DM646X_VLQINT] = 7, + [IRQ_I2C] = 7, + [IRQ_UARTINT0] = 7, + [IRQ_UARTINT1] = 7, + [IRQ_DM646X_UARTINT2] = 7, + [IRQ_DM646X_SPINT0] = 7, + [IRQ_DM646X_SPINT1] = 7, + [IRQ_DM646X_DSP2ARMINT] = 7, + [IRQ_DM646X_RESERVED_4] = 7, + [IRQ_DM646X_PSCINT] = 7, + [IRQ_DM646X_GPIO0] = 7, + [IRQ_DM646X_GPIO1] = 7, + [IRQ_DM646X_GPIO2] = 7, + [IRQ_DM646X_GPIO3] = 7, + [IRQ_DM646X_GPIO4] = 7, + [IRQ_DM646X_GPIO5] = 7, + [IRQ_DM646X_GPIO6] = 7, + [IRQ_DM646X_GPIO7] = 7, + [IRQ_DM646X_GPIOBNK0] = 7, + [IRQ_DM646X_GPIOBNK1] = 7, + [IRQ_DM646X_GPIOBNK2] = 7, + [IRQ_DM646X_DDRINT] = 7, + [IRQ_DM646X_AEMIFINT] = 7, + [IRQ_COMMTX] = 7, + [IRQ_COMMRX] = 7, + [IRQ_EMUINT] = 7, +}; + +static const u8 dm355_default_priorities[DAVINCI_N_AINTC_IRQ] = { + [IRQ_DM355_CCDC_VDINT0] = 2, + [IRQ_DM355_CCDC_VDINT1] = 6, + [IRQ_DM355_CCDC_VDINT2] = 6, + [IRQ_DM355_IPIPE_HST] = 6, + [IRQ_DM355_H3AINT] = 6, + [IRQ_DM355_IPIPE_SDR] = 6, + [IRQ_DM355_IPIPEIFINT] = 6, + [IRQ_DM355_OSDINT] = 7, + [IRQ_DM355_VENCINT] = 6, + [IRQ_ASQINT] = 6, + [IRQ_IMXINT] = 6, + [IRQ_USBINT] = 4, + [IRQ_DM355_RTOINT] = 4, + [IRQ_DM355_UARTINT2] = 7, + [IRQ_DM355_TINT6] = 7, + [IRQ_CCINT0] = 5, /* dma */ + [IRQ_CCERRINT] = 5, /* dma */ + [IRQ_TCERRINT0] = 5, /* dma */ + [IRQ_TCERRINT] = 5, /* dma */ + [IRQ_DM355_SPINT2_1] = 7, + [IRQ_DM355_TINT7] = 4, + [IRQ_DM355_SDIOINT0] = 7, + [IRQ_MBXINT] = 7, + [IRQ_MBRINT] = 7, + [IRQ_MMCINT] = 7, + [IRQ_DM355_MMCINT1] = 7, + [IRQ_DM355_PWMINT3] = 7, + [IRQ_DDRINT] = 7, + [IRQ_AEMIFINT] = 7, + [IRQ_DM355_SDIOINT1] = 4, + [IRQ_TINT0_TINT12] = 2, /* clockevent */ + [IRQ_TINT0_TINT34] = 2, /* clocksource */ + [IRQ_TINT1_TINT12] = 7, /* DSP timer */ + [IRQ_TINT1_TINT34] = 7, /* system tick */ + [IRQ_PWMINT0] = 7, + [IRQ_PWMINT1] = 7, + [IRQ_PWMINT2] = 7, + [IRQ_I2C] = 3, + [IRQ_UARTINT0] = 3, + [IRQ_UARTINT1] = 3, + [IRQ_DM355_SPINT0_0] = 3, + [IRQ_DM355_SPINT0_1] = 3, + [IRQ_DM355_GPIO0] = 3, + [IRQ_DM355_GPIO1] = 7, + [IRQ_DM355_GPIO2] = 4, + [IRQ_DM355_GPIO3] = 4, + [IRQ_DM355_GPIO4] = 7, + [IRQ_DM355_GPIO5] = 7, + [IRQ_DM355_GPIO6] = 7, + [IRQ_DM355_GPIO7] = 7, + [IRQ_DM355_GPIO8] = 7, + [IRQ_DM355_GPIO9] = 7, + [IRQ_DM355_GPIOBNK0] = 7, + [IRQ_DM355_GPIOBNK1] = 7, + [IRQ_DM355_GPIOBNK2] = 7, + [IRQ_DM355_GPIOBNK3] = 7, + [IRQ_DM355_GPIOBNK4] = 7, + [IRQ_DM355_GPIOBNK5] = 7, + [IRQ_DM355_GPIOBNK6] = 7, + [IRQ_COMMTX] = 7, + [IRQ_COMMRX] = 7, + [IRQ_EMUINT] = 7, +}; + /* ARM Interrupt Controller Initialization */ void __init davinci_irq_init(void) { unsigned i; - const u8 *priority = default_priorities; + + if (cpu_is_davinci_dm644x()) + davinci_def_priorities = dm644x_default_priorities; + else if (cpu_is_davinci_dm646x()) + davinci_def_priorities = dm646x_default_priorities; + else if (cpu_is_davinci_dm355()) + davinci_def_priorities = dm355_default_priorities; /* Clear all interrupt requests */ davinci_irq_writel(~0x0, FIQ_REG0_OFFSET); @@ -209,8 +351,8 @@ void __init davinci_irq_init(void) unsigned j; u32 pri; - for (j = 0, pri = 0; j < 32; j += 4, priority++) - pri |= (*priority & 0x07) << j; + for (j = 0, pri = 0; j < 32; j += 4, davinci_def_priorities++) + pri |= (*davinci_def_priorities & 0x07) << j; davinci_irq_writel(pri, i); } diff --git a/arch/arm/mach-davinci/mux.c b/arch/arm/mach-davinci/mux.c index 8ff9d8aca60..bbba0b247a4 100644 --- a/arch/arm/mach-davinci/mux.c +++ b/arch/arm/mach-davinci/mux.c @@ -1,41 +1,103 @@ /* - * DaVinci pin multiplexing configurations + * Utility to set the DAVINCI MUX register from a table in mux.h * * Author: Vladimir Barinov, MontaVista Software, Inc. <source@mvista.com> * + * Based on linux/arch/arm/plat-omap/mux.c: + * Copyright (C) 2003 - 2005 Nokia Corporation + * + * Written by Tony Lindgren + * * 2007 (c) MontaVista Software, Inc. This file is licensed under * the terms of the GNU General Public License version 2. This program * is licensed "as is" without any warranty of any kind, whether express * or implied. + * + * Copyright (C) 2008 Texas Instruments. */ #include <linux/io.h> +#include <linux/module.h> #include <linux/spinlock.h> #include <mach/hardware.h> - #include <mach/mux.h> -/* System control register offsets */ -#define PINMUX0 0x00 -#define PINMUX1 0x04 +static const struct mux_config *mux_table; +static unsigned long pin_table_sz; + +int __init davinci_mux_register(const struct mux_config *pins, + unsigned long size) +{ + mux_table = pins; + pin_table_sz = size; -static DEFINE_SPINLOCK(mux_lock); + return 0; +} -void davinci_mux_peripheral(unsigned int mux, unsigned int enable) +/* + * Sets the DAVINCI MUX register based on the table + */ +int __init_or_module davinci_cfg_reg(const unsigned long index) { - u32 pinmux, muxreg = PINMUX0; + static DEFINE_SPINLOCK(mux_spin_lock); + void __iomem *base = IO_ADDRESS(DAVINCI_SYSTEM_MODULE_BASE); + unsigned long flags; + const struct mux_config *cfg; + unsigned int reg_orig = 0, reg = 0; + unsigned int mask, warn = 0; + + if (!mux_table) + BUG(); + + if (index >= pin_table_sz) { + printk(KERN_ERR "Invalid pin mux index: %lu (%lu)\n", + index, pin_table_sz); + dump_stack(); + return -ENODEV; + } + + cfg = &mux_table[index]; + + if (cfg->name == NULL) { + printk(KERN_ERR "No entry for the specified index\n"); + return -ENODEV; + } + + /* Update the mux register in question */ + if (cfg->mask) { + unsigned tmp1, tmp2; + + spin_lock_irqsave(&mux_spin_lock, flags); + reg_orig = __raw_readl(base + cfg->mux_reg); + + mask = (cfg->mask << cfg->mask_offset); + tmp1 = reg_orig & mask; + reg = reg_orig & ~mask; + + tmp2 = (cfg->mode << cfg->mask_offset); + reg |= tmp2; + + if (tmp1 != tmp2) + warn = 1; + + __raw_writel(reg, base + cfg->mux_reg); + spin_unlock_irqrestore(&mux_spin_lock, flags); + } + + if (warn) { +#ifdef CONFIG_DAVINCI_MUX_WARNINGS + printk(KERN_WARNING "MUX: initialized %s\n", cfg->name); +#endif + } - if (mux >= DAVINCI_MUX_LEVEL2) { - muxreg = PINMUX1; - mux -= DAVINCI_MUX_LEVEL2; +#ifdef CONFIG_DAVINCI_MUX_DEBUG + if (cfg->debug || warn) { + printk(KERN_WARNING "MUX: Setting register %s\n", cfg->name); + printk(KERN_WARNING " %s (0x%08x) = 0x%08x -> 0x%08x\n", + cfg->mux_reg_name, cfg->mux_reg, reg_orig, reg); } +#endif - spin_lock(&mux_lock); - pinmux = davinci_readl(DAVINCI_SYSTEM_MODULE_BASE + muxreg); - if (enable) - pinmux |= (1 << mux); - else - pinmux &= ~(1 << mux); - davinci_writel(pinmux, DAVINCI_SYSTEM_MODULE_BASE + muxreg); - spin_unlock(&mux_lock); + return 0; } +EXPORT_SYMBOL(davinci_cfg_reg); diff --git a/arch/arm/mach-davinci/mux.h b/arch/arm/mach-davinci/mux.h new file mode 100644 index 00000000000..adc86941337 --- /dev/null +++ b/arch/arm/mach-davinci/mux.h @@ -0,0 +1,51 @@ +/* + * Pin-multiplex helper macros for TI DaVinci family devices + * + * Author: Vladimir Barinov, MontaVista Software, Inc. <source@mvista.com> + * + * 2007 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + * Copyright (C) 2008 Texas Instruments. + */ +#ifndef _MACH_DAVINCI_MUX_H_ +#define _MACH_DAVINCI_MUX_H_ + +#include <mach/mux.h> + +#define MUX_CFG(soc, desc, muxreg, mode_offset, mode_mask, mux_mode, dbg)\ +[soc##_##desc] = { \ + .name = #desc, \ + .debug = dbg, \ + .mux_reg_name = "PINMUX"#muxreg, \ + .mux_reg = PINMUX##muxreg, \ + .mask_offset = mode_offset, \ + .mask = mode_mask, \ + .mode = mux_mode, \ + }, + +#define INT_CFG(soc, desc, mode_offset, mode_mask, mux_mode, dbg) \ +[soc##_##desc] = { \ + .name = #desc, \ + .debug = dbg, \ + .mux_reg_name = "INTMUX", \ + .mux_reg = INTMUX, \ + .mask_offset = mode_offset, \ + .mask = mode_mask, \ + .mode = mux_mode, \ + }, + +#define EVT_CFG(soc, desc, mode_offset, mode_mask, mux_mode, dbg) \ +[soc##_##desc] = { \ + .name = #desc, \ + .debug = dbg, \ + .mux_reg_name = "EVTMUX", \ + .mux_reg = EVTMUX, \ + .mask_offset = mode_offset, \ + .mask = mode_mask, \ + .mode = mux_mode, \ + }, + +#endif /* _MACH_DAVINCI_MUX_H */ diff --git a/arch/arm/mach-davinci/psc.c b/arch/arm/mach-davinci/psc.c index 58754f066d5..84171abf5f7 100644 --- a/arch/arm/mach-davinci/psc.c +++ b/arch/arm/mach-davinci/psc.c @@ -23,10 +23,13 @@ #include <linux/init.h> #include <linux/io.h> +#include <mach/cputype.h> #include <mach/hardware.h> #include <mach/psc.h> #include <mach/mux.h> +#define DAVINCI_PWR_SLEEP_CNTRL_BASE 0x01C41000 + /* PSC register offsets */ #define EPCPR 0x070 #define PTCMD 0x120 @@ -36,102 +39,61 @@ #define MDSTAT 0x800 #define MDCTL 0xA00 -/* System control register offsets */ -#define VDD3P3V_PWDN 0x48 +#define MDSTAT_STATE_MASK 0x1f -static void davinci_psc_mux(unsigned int id) +/* Return nonzero iff the domain's clock is active */ +int __init davinci_psc_is_clk_active(unsigned int id) { - switch (id) { - case DAVINCI_LPSC_ATA: - davinci_mux_peripheral(DAVINCI_MUX_HDIREN, 1); - davinci_mux_peripheral(DAVINCI_MUX_ATAEN, 1); - break; - case DAVINCI_LPSC_MMC_SD: - /* VDD power manupulations are done in U-Boot for CPMAC - * so applies to MMC as well - */ - /*Set up the pull regiter for MMC */ - davinci_writel(0, DAVINCI_SYSTEM_MODULE_BASE + VDD3P3V_PWDN); - davinci_mux_peripheral(DAVINCI_MUX_MSTK, 0); - break; - case DAVINCI_LPSC_I2C: - davinci_mux_peripheral(DAVINCI_MUX_I2C, 1); - break; - case DAVINCI_LPSC_McBSP: - davinci_mux_peripheral(DAVINCI_MUX_ASP, 1); - break; - default: - break; - } + void __iomem *psc_base = IO_ADDRESS(DAVINCI_PWR_SLEEP_CNTRL_BASE); + u32 mdstat = __raw_readl(psc_base + MDSTAT + 4 * id); + + /* if clocked, state can be "Enable" or "SyncReset" */ + return mdstat & BIT(12); } /* Enable or disable a PSC domain */ void davinci_psc_config(unsigned int domain, unsigned int id, char enable) { - u32 epcpr, ptcmd, ptstat, pdstat, pdctl1, mdstat, mdctl, mdstat_mask; + u32 epcpr, ptcmd, ptstat, pdstat, pdctl1, mdstat, mdctl; + void __iomem *psc_base = IO_ADDRESS(DAVINCI_PWR_SLEEP_CNTRL_BASE); + u32 next_state = enable ? 0x3 : 0x2; /* 0x3 enables, 0x2 disables */ - mdctl = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + MDCTL + 4 * id); - if (enable) - mdctl |= 0x00000003; /* Enable Module */ - else - mdctl &= 0xFFFFFFF2; /* Disable Module */ - davinci_writel(mdctl, DAVINCI_PWR_SLEEP_CNTRL_BASE + MDCTL + 4 * id); + mdctl = __raw_readl(psc_base + MDCTL + 4 * id); + mdctl &= ~MDSTAT_STATE_MASK; + mdctl |= next_state; + __raw_writel(mdctl, psc_base + MDCTL + 4 * id); - pdstat = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + PDSTAT); + pdstat = __raw_readl(psc_base + PDSTAT); if ((pdstat & 0x00000001) == 0) { - pdctl1 = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + PDCTL1); + pdctl1 = __raw_readl(psc_base + PDCTL1); pdctl1 |= 0x1; - davinci_writel(pdctl1, DAVINCI_PWR_SLEEP_CNTRL_BASE + PDCTL1); + __raw_writel(pdctl1, psc_base + PDCTL1); ptcmd = 1 << domain; - davinci_writel(ptcmd, DAVINCI_PWR_SLEEP_CNTRL_BASE + PTCMD); + __raw_writel(ptcmd, psc_base + PTCMD); do { - epcpr = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + - EPCPR); + epcpr = __raw_readl(psc_base + EPCPR); } while ((((epcpr >> domain) & 1) == 0)); - pdctl1 = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + PDCTL1); + pdctl1 = __raw_readl(psc_base + PDCTL1); pdctl1 |= 0x100; - davinci_writel(pdctl1, DAVINCI_PWR_SLEEP_CNTRL_BASE + PDCTL1); + __raw_writel(pdctl1, psc_base + PDCTL1); do { - ptstat = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + + ptstat = __raw_readl(psc_base + PTSTAT); } while (!(((ptstat >> domain) & 1) == 0)); } else { ptcmd = 1 << domain; - davinci_writel(ptcmd, DAVINCI_PWR_SLEEP_CNTRL_BASE + PTCMD); + __raw_writel(ptcmd, psc_base + PTCMD); do { - ptstat = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + - PTSTAT); + ptstat = __raw_readl(psc_base + PTSTAT); } while (!(((ptstat >> domain) & 1) == 0)); } - if (enable) - mdstat_mask = 0x3; - else - mdstat_mask = 0x2; - do { - mdstat = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + - MDSTAT + 4 * id); - } while (!((mdstat & 0x0000001F) == mdstat_mask)); - - if (enable) - davinci_psc_mux(id); -} - -void __init davinci_psc_init(void) -{ - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_VPSSMSTR, 1); - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_VPSSSLV, 1); - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_TPCC, 1); - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_TPTC0, 1); - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_TPTC1, 1); - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_GPIO, 1); - - /* Turn on WatchDog timer LPSC. Needed for RESET to work */ - davinci_psc_config(DAVINCI_GPSC_ARMDOMAIN, DAVINCI_LPSC_TIMER2, 1); + mdstat = __raw_readl(psc_base + MDSTAT + 4 * id); + } while (!((mdstat & MDSTAT_STATE_MASK) == next_state)); } diff --git a/arch/arm/mach-davinci/serial.c b/arch/arm/mach-davinci/serial.c index 3010f997125..69507579652 100644 --- a/arch/arm/mach-davinci/serial.c +++ b/arch/arm/mach-davinci/serial.c @@ -32,32 +32,47 @@ #include <mach/hardware.h> #include <mach/serial.h> #include <mach/irqs.h> +#include <mach/cputype.h> +#include "clock.h" -#define UART_DAVINCI_PWREMU 0x0c - -static inline unsigned int davinci_serial_in(struct plat_serial8250_port *up, - int offset) +static inline unsigned int serial_read_reg(struct plat_serial8250_port *up, + int offset) { offset <<= up->regshift; - return (unsigned int)__raw_readb(up->membase + offset); + return (unsigned int)__raw_readl(IO_ADDRESS(up->mapbase) + offset); } -static inline void davinci_serial_outp(struct plat_serial8250_port *p, - int offset, int value) +static inline void serial_write_reg(struct plat_serial8250_port *p, int offset, + int value) { offset <<= p->regshift; - __raw_writeb(value, p->membase + offset); + __raw_writel(value, IO_ADDRESS(p->mapbase) + offset); } static struct plat_serial8250_port serial_platform_data[] = { { - .membase = (char *)IO_ADDRESS(DAVINCI_UART0_BASE), - .mapbase = (unsigned long)DAVINCI_UART0_BASE, + .mapbase = DAVINCI_UART0_BASE, .irq = IRQ_UARTINT0, - .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | + UPF_IOREMAP, + .iotype = UPIO_MEM, + .regshift = 2, + }, + { + .mapbase = DAVINCI_UART1_BASE, + .irq = IRQ_UARTINT1, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | + UPF_IOREMAP, + .iotype = UPIO_MEM, + .regshift = 2, + }, + { + .mapbase = DAVINCI_UART2_BASE, + .irq = IRQ_UARTINT2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | + UPF_IOREMAP, .iotype = UPIO_MEM, .regshift = 2, - .uartclk = 27000000, }, { .flags = 0 @@ -74,22 +89,68 @@ static struct platform_device serial_device = { static void __init davinci_serial_reset(struct plat_serial8250_port *p) { - /* reset both transmitter and receiver: bits 14,13 = UTRST, URRST */ unsigned int pwremu = 0; - davinci_serial_outp(p, UART_IER, 0); /* disable all interrupts */ + serial_write_reg(p, UART_IER, 0); /* disable all interrupts */ - davinci_serial_outp(p, UART_DAVINCI_PWREMU, pwremu); + /* reset both transmitter and receiver: bits 14,13 = UTRST, URRST */ + serial_write_reg(p, UART_DAVINCI_PWREMU, pwremu); mdelay(10); pwremu |= (0x3 << 13); pwremu |= 0x1; - davinci_serial_outp(p, UART_DAVINCI_PWREMU, pwremu); + serial_write_reg(p, UART_DAVINCI_PWREMU, pwremu); + + if (cpu_is_davinci_dm646x()) + serial_write_reg(p, UART_DM646X_SCR, + UART_DM646X_SCR_TX_WATERMARK); +} + +void __init davinci_serial_init(struct davinci_uart_config *info) +{ + int i; + char name[16]; + struct clk *uart_clk; + struct device *dev = &serial_device.dev; + + /* + * Make sure the serial ports are muxed on at this point. + * You have to mux them off in device drivers later on + * if not needed. + */ + for (i = 0; i < DAVINCI_MAX_NR_UARTS; i++) { + struct plat_serial8250_port *p = serial_platform_data + i; + + if (!(info->enabled_uarts & (1 << i))) { + p->flags = 0; + continue; + } + + if (cpu_is_davinci_dm646x()) + p->iotype = UPIO_MEM32; + + if (cpu_is_davinci_dm355()) { + if (i == 2) { + p->mapbase = (unsigned long)DM355_UART2_BASE; + p->irq = IRQ_DM355_UARTINT2; + } + } + + sprintf(name, "uart%d", i); + uart_clk = clk_get(dev, name); + if (IS_ERR(uart_clk)) + printk(KERN_ERR "%s:%d: failed to get UART%d clock\n", + __func__, __LINE__, i); + else { + clk_enable(uart_clk); + p->uartclk = clk_get_rate(uart_clk); + davinci_serial_reset(p); + } + } } static int __init davinci_init(void) { - davinci_serial_reset(&serial_platform_data[0]); return platform_device_register(&serial_device); } diff --git a/arch/arm/mach-davinci/time.c b/arch/arm/mach-davinci/time.c index 6c227d4ba99..494e01bff5c 100644 --- a/arch/arm/mach-davinci/time.c +++ b/arch/arm/mach-davinci/time.c @@ -16,6 +16,9 @@ #include <linux/clockchips.h> #include <linux/spinlock.h> #include <linux/io.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/device.h> #include <mach/hardware.h> #include <asm/system.h> @@ -24,8 +27,11 @@ #include <asm/mach/time.h> #include <asm/errno.h> #include <mach/io.h> +#include <mach/cputype.h> +#include "clock.h" static struct clock_event_device clockevent_davinci; +static unsigned int davinci_clock_tick_rate; #define DAVINCI_TIMER0_BASE (IO_PHYS + 0x21400) #define DAVINCI_TIMER1_BASE (IO_PHYS + 0x21800) @@ -99,9 +105,9 @@ struct timer_s { unsigned int id; unsigned long period; unsigned long opts; - unsigned long reg_base; - unsigned long tim_reg; - unsigned long prd_reg; + void __iomem *base; + unsigned long tim_off; + unsigned long prd_off; unsigned long enamode_shift; struct irqaction irqaction; }; @@ -114,15 +120,15 @@ static struct timer_s timers[]; static int timer32_config(struct timer_s *t) { - u32 tcr = davinci_readl(t->reg_base + TCR); + u32 tcr = __raw_readl(t->base + TCR); /* disable timer */ tcr &= ~(TCR_ENAMODE_MASK << t->enamode_shift); - davinci_writel(tcr, t->reg_base + TCR); + __raw_writel(tcr, t->base + TCR); /* reset counter to zero, set new period */ - davinci_writel(0, t->tim_reg); - davinci_writel(t->period, t->prd_reg); + __raw_writel(0, t->base + t->tim_off); + __raw_writel(t->period, t->base + t->prd_off); /* Set enable mode */ if (t->opts & TIMER_OPTS_ONESHOT) { @@ -131,13 +137,13 @@ static int timer32_config(struct timer_s *t) tcr |= TCR_ENAMODE_PERIODIC << t->enamode_shift; } - davinci_writel(tcr, t->reg_base + TCR); + __raw_writel(tcr, t->base + TCR); return 0; } static inline u32 timer32_read(struct timer_s *t) { - return davinci_readl(t->tim_reg); + return __raw_readl(t->base + t->tim_off); } static irqreturn_t timer_interrupt(int irq, void *dev_id) @@ -176,51 +182,54 @@ static struct timer_s timers[] = { static void __init timer_init(void) { - u32 bases[] = {DAVINCI_TIMER0_BASE, DAVINCI_TIMER1_BASE}; + u32 phys_bases[] = {DAVINCI_TIMER0_BASE, DAVINCI_TIMER1_BASE}; int i; /* Global init of each 64-bit timer as a whole */ for(i=0; i<2; i++) { - u32 tgcr, base = bases[i]; + u32 tgcr; + void __iomem *base = IO_ADDRESS(phys_bases[i]); /* Disabled, Internal clock source */ - davinci_writel(0, base + TCR); + __raw_writel(0, base + TCR); /* reset both timers, no pre-scaler for timer34 */ tgcr = 0; - davinci_writel(tgcr, base + TGCR); + __raw_writel(tgcr, base + TGCR); /* Set both timers to unchained 32-bit */ tgcr = TGCR_TIMMODE_32BIT_UNCHAINED << TGCR_TIMMODE_SHIFT; - davinci_writel(tgcr, base + TGCR); + __raw_writel(tgcr, base + TGCR); /* Unreset timers */ tgcr |= (TGCR_UNRESET << TGCR_TIM12RS_SHIFT) | (TGCR_UNRESET << TGCR_TIM34RS_SHIFT); - davinci_writel(tgcr, base + TGCR); + __raw_writel(tgcr, base + TGCR); /* Init both counters to zero */ - davinci_writel(0, base + TIM12); - davinci_writel(0, base + TIM34); + __raw_writel(0, base + TIM12); + __raw_writel(0, base + TIM34); } /* Init of each timer as a 32-bit timer */ for (i=0; i< ARRAY_SIZE(timers); i++) { struct timer_s *t = &timers[i]; + u32 phys_base; if (t->name) { t->id = i; - t->reg_base = (IS_TIMER1(t->id) ? + phys_base = (IS_TIMER1(t->id) ? DAVINCI_TIMER1_BASE : DAVINCI_TIMER0_BASE); + t->base = IO_ADDRESS(phys_base); if (IS_TIMER_BOT(t->id)) { t->enamode_shift = 6; - t->tim_reg = t->reg_base + TIM12; - t->prd_reg = t->reg_base + PRD12; + t->tim_off = TIM12; + t->prd_off = PRD12; } else { t->enamode_shift = 22; - t->tim_reg = t->reg_base + TIM34; - t->prd_reg = t->reg_base + PRD34; + t->tim_off = TIM34; + t->prd_off = PRD34; } /* Register interrupt */ @@ -274,7 +283,7 @@ static void davinci_set_mode(enum clock_event_mode mode, switch (mode) { case CLOCK_EVT_MODE_PERIODIC: - t->period = CLOCK_TICK_RATE / (HZ); + t->period = davinci_clock_tick_rate / (HZ); t->opts = TIMER_OPTS_PERIODIC; timer32_config(t); break; @@ -301,21 +310,29 @@ static struct clock_event_device clockevent_davinci = { static void __init davinci_timer_init(void) { + struct clk *timer_clk; + static char err[] __initdata = KERN_ERR "%s: can't register clocksource!\n"; /* init timer hw */ timer_init(); + timer_clk = clk_get(NULL, "timer0"); + BUG_ON(IS_ERR(timer_clk)); + clk_enable(timer_clk); + + davinci_clock_tick_rate = clk_get_rate(timer_clk); + /* setup clocksource */ clocksource_davinci.mult = - clocksource_khz2mult(CLOCK_TICK_RATE/1000, + clocksource_khz2mult(davinci_clock_tick_rate/1000, clocksource_davinci.shift); if (clocksource_register(&clocksource_davinci)) printk(err, clocksource_davinci.name); /* setup clockevent */ - clockevent_davinci.mult = div_sc(CLOCK_TICK_RATE, NSEC_PER_SEC, + clockevent_davinci.mult = div_sc(davinci_clock_tick_rate, NSEC_PER_SEC, clockevent_davinci.shift); clockevent_davinci.max_delta_ns = clockevent_delta2ns(0xfffffffe, &clockevent_davinci); @@ -333,42 +350,52 @@ struct sys_timer davinci_timer = { /* reset board using watchdog timer */ void davinci_watchdog_reset(void) { - u32 tgcr, wdtcr, base = DAVINCI_WDOG_BASE; + u32 tgcr, wdtcr; + void __iomem *base = IO_ADDRESS(DAVINCI_WDOG_BASE); + struct device dev; + struct clk *wd_clk; + char *name = "watchdog"; + + dev_set_name(&dev, name); + wd_clk = clk_get(&dev, NULL); + if (WARN_ON(IS_ERR(wd_clk))) + return; + clk_enable(wd_clk); /* disable, internal clock source */ - davinci_writel(0, base + TCR); + __raw_writel(0, base + TCR); /* reset timer, set mode to 64-bit watchdog, and unreset */ tgcr = 0; - davinci_writel(tgcr, base + TCR); + __raw_writel(tgcr, base + TCR); tgcr = TGCR_TIMMODE_64BIT_WDOG << TGCR_TIMMODE_SHIFT; tgcr |= (TGCR_UNRESET << TGCR_TIM12RS_SHIFT) | (TGCR_UNRESET << TGCR_TIM34RS_SHIFT); - davinci_writel(tgcr, base + TCR); + __raw_writel(tgcr, base + TCR); /* clear counter and period regs */ - davinci_writel(0, base + TIM12); - davinci_writel(0, base + TIM34); - davinci_writel(0, base + PRD12); - davinci_writel(0, base + PRD34); + __raw_writel(0, base + TIM12); + __raw_writel(0, base + TIM34); + __raw_writel(0, base + PRD12); + __raw_writel(0, base + PRD34); /* enable */ - wdtcr = davinci_readl(base + WDTCR); + wdtcr = __raw_readl(base + WDTCR); wdtcr |= WDTCR_WDEN_ENABLE << WDTCR_WDEN_SHIFT; - davinci_writel(wdtcr, base + WDTCR); + __raw_writel(wdtcr, base + WDTCR); /* put watchdog in pre-active state */ wdtcr = (WDTCR_WDKEY_SEQ0 << WDTCR_WDKEY_SHIFT) | (WDTCR_WDEN_ENABLE << WDTCR_WDEN_SHIFT); - davinci_writel(wdtcr, base + WDTCR); + __raw_writel(wdtcr, base + WDTCR); /* put watchdog in active state */ wdtcr = (WDTCR_WDKEY_SEQ1 << WDTCR_WDKEY_SHIFT) | (WDTCR_WDEN_ENABLE << WDTCR_WDEN_SHIFT); - davinci_writel(wdtcr, base + WDTCR); + __raw_writel(wdtcr, base + WDTCR); /* write an invalid value to the WDKEY field to trigger * a watchdog reset */ wdtcr = 0x00004000; - davinci_writel(wdtcr, base + WDTCR); + __raw_writel(wdtcr, base + WDTCR); } diff --git a/arch/arm/mach-davinci/usb.c b/arch/arm/mach-davinci/usb.c index 2429b79f6da..abedb633718 100644 --- a/arch/arm/mach-davinci/usb.c +++ b/arch/arm/mach-davinci/usb.c @@ -14,6 +14,8 @@ #include <mach/hardware.h> #include <mach/irqs.h> +#define DAVINCI_USB_OTG_BASE 0x01C64000 + #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE) static struct musb_hdrc_eps_bits musb_eps[] = { { "ep1_tx", 8, }, diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig deleted file mode 100644 index cddd194ac6e..00000000000 --- a/arch/arm/mach-imx/Kconfig +++ /dev/null @@ -1,11 +0,0 @@ -menu "IMX Implementations" - depends on ARCH_IMX - -config ARCH_MX1ADS - bool "mx1ads" - depends on ARCH_IMX - select ISA - help - Say Y here if you are using the Motorola MX1ADS board - -endmenu diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile deleted file mode 100644 index b047c7e795a..00000000000 --- a/arch/arm/mach-imx/Makefile +++ /dev/null @@ -1,18 +0,0 @@ -# -# Makefile for the linux kernel. -# - -# Object file lists. - -obj-y += irq.o time.o dma.o generic.o clock.o - -obj-$(CONFIG_CPU_FREQ_IMX) += cpufreq.o - -# Specific board support -obj-$(CONFIG_ARCH_MX1ADS) += mx1ads.o - -# Support for blinky lights -led-y := leds.o - -obj-$(CONFIG_LEDS) += $(led-y) -led-$(CONFIG_ARCH_MX1ADS) += leds-mx1ads.o diff --git a/arch/arm/mach-imx/Makefile.boot b/arch/arm/mach-imx/Makefile.boot deleted file mode 100644 index fd72ce5b808..00000000000 --- a/arch/arm/mach-imx/Makefile.boot +++ /dev/null @@ -1,2 +0,0 @@ - zreladdr-$(CONFIG_ARCH_MX1ADS) := 0x08008000 - diff --git a/arch/arm/mach-imx/clock.c b/arch/arm/mach-imx/clock.c deleted file mode 100644 index cf332aeb942..00000000000 --- a/arch/arm/mach-imx/clock.c +++ /dev/null @@ -1,210 +0,0 @@ -/* - * Copyright (C) 2008 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include <linux/kernel.h> -#include <linux/device.h> -#include <linux/list.h> -#include <linux/math64.h> -#include <linux/err.h> -#include <linux/io.h> - -#include <mach/hardware.h> - -/* - * Very simple approach: We can't disable clocks, so we do - * not need refcounting - */ - -struct clk { - struct list_head node; - const char *name; - unsigned long (*get_rate)(void); -}; - -/* - * get the system pll clock in Hz - * - * mfi + mfn / (mfd +1) - * f = 2 * f_ref * -------------------- - * pd + 1 - */ -static unsigned long imx_decode_pll(unsigned int pll, u32 f_ref) -{ - unsigned long long ll; - unsigned long quot; - - u32 mfi = (pll >> 10) & 0xf; - u32 mfn = pll & 0x3ff; - u32 mfd = (pll >> 16) & 0x3ff; - u32 pd = (pll >> 26) & 0xf; - - mfi = mfi <= 5 ? 5 : mfi; - - ll = 2 * (unsigned long long)f_ref * - ((mfi << 16) + (mfn << 16) / (mfd + 1)); - quot = (pd + 1) * (1 << 16); - ll += quot / 2; - do_div(ll, quot); - return (unsigned long)ll; -} - -static unsigned long imx_get_system_clk(void) -{ - u32 f_ref = (CSCR & CSCR_SYSTEM_SEL) ? 16000000 : (CLK32 * 512); - - return imx_decode_pll(SPCTL0, f_ref); -} - -static unsigned long imx_get_mcu_clk(void) -{ - return imx_decode_pll(MPCTL0, CLK32 * 512); -} - -/* - * get peripheral clock 1 ( UART[12], Timer[12], PWM ) - */ -static unsigned long imx_get_perclk1(void) -{ - return imx_get_system_clk() / (((PCDR) & 0xf)+1); -} - -/* - * get peripheral clock 2 ( LCD, SD, SPI[12] ) - */ -static unsigned long imx_get_perclk2(void) -{ - return imx_get_system_clk() / (((PCDR>>4) & 0xf)+1); -} - -/* - * get peripheral clock 3 ( SSI ) - */ -static unsigned long imx_get_perclk3(void) -{ - return imx_get_system_clk() / (((PCDR>>16) & 0x7f)+1); -} - -/* - * get hclk ( SDRAM, CSI, Memory Stick, I2C, DMA ) - */ -static unsigned long imx_get_hclk(void) -{ - return imx_get_system_clk() / (((CSCR>>10) & 0xf)+1); -} - -static struct clk clk_system_clk = { - .name = "system_clk", - .get_rate = imx_get_system_clk, -}; - -static struct clk clk_hclk = { - .name = "hclk", - .get_rate = imx_get_hclk, -}; - -static struct clk clk_mcu_clk = { - .name = "mcu_clk", - .get_rate = imx_get_mcu_clk, -}; - -static struct clk clk_perclk1 = { - .name = "perclk1", - .get_rate = imx_get_perclk1, -}; - -static struct clk clk_uart_clk = { - .name = "uart_clk", - .get_rate = imx_get_perclk1, -}; - -static struct clk clk_perclk2 = { - .name = "perclk2", - .get_rate = imx_get_perclk2, -}; - -static struct clk clk_perclk3 = { - .name = "perclk3", - .get_rate = imx_get_perclk3, -}; - -static struct clk *clks[] = { - &clk_perclk1, - &clk_perclk2, - &clk_perclk3, - &clk_system_clk, - &clk_hclk, - &clk_mcu_clk, - &clk_uart_clk, -}; - -static LIST_HEAD(clocks); -static DEFINE_MUTEX(clocks_mutex); - -struct clk *clk_get(struct device *dev, const char *id) -{ - struct clk *p, *clk = ERR_PTR(-ENOENT); - - mutex_lock(&clocks_mutex); - list_for_each_entry(p, &clocks, node) { - if (!strcmp(p->name, id)) { - clk = p; - goto found; - } - } - -found: - mutex_unlock(&clocks_mutex); - - return clk; -} -EXPORT_SYMBOL(clk_get); - -void clk_put(struct clk *clk) -{ -} -EXPORT_SYMBOL(clk_put); - -int clk_enable(struct clk *clk) -{ - return 0; -} -EXPORT_SYMBOL(clk_enable); - -void clk_disable(struct clk *clk) -{ -} -EXPORT_SYMBOL(clk_disable); - -unsigned long clk_get_rate(struct clk *clk) -{ - return clk->get_rate(); -} -EXPORT_SYMBOL(clk_get_rate); - -int imx_clocks_init(void) -{ - int i; - - mutex_lock(&clocks_mutex); - for (i = 0; i < ARRAY_SIZE(clks); i++) - list_add(&clks[i]->node, &clocks); - mutex_unlock(&clocks_mutex); - - return 0; -} - diff --git a/arch/arm/mach-imx/cpufreq.c b/arch/arm/mach-imx/cpufreq.c deleted file mode 100644 index 434b4ca0af6..00000000000 --- a/arch/arm/mach-imx/cpufreq.c +++ /dev/null @@ -1,315 +0,0 @@ -/* - * cpu.c: clock scaling for the iMX - * - * Copyright (C) 2000 2001, The Delft University of Technology - * Copyright (c) 2004 Sascha Hauer <sascha@saschahauer.de> - * Copyright (C) 2006 Inky Lung <ilung@cwlinux.com> - * Copyright (C) 2006 Pavel Pisa, PiKRON <ppisa@pikron.com> - * - * Based on SA1100 version written by: - * - Johan Pouwelse (J.A.Pouwelse@its.tudelft.nl): initial version - * - Erik Mouw (J.A.K.Mouw@its.tudelft.nl): - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -/*#define DEBUG*/ - -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/cpufreq.h> -#include <linux/clk.h> -#include <linux/err.h> -#include <asm/system.h> - -#include <mach/hardware.h> - -#include "generic.h" - -#ifndef __val2mfld -#define __val2mfld(mask,val) (((mask)&~((mask)<<1))*(val)&(mask)) -#endif -#ifndef __mfld2val -#define __mfld2val(mask,val) (((val)&(mask))/((mask)&~((mask)<<1))) -#endif - -#define CR_920T_CLOCK_MODE 0xC0000000 -#define CR_920T_FASTBUS_MODE 0x00000000 -#define CR_920T_ASYNC_MODE 0xC0000000 - -static u32 mpctl0_at_boot; -static u32 bclk_div_at_boot; - -static struct clk *system_clk, *mcu_clk; - -static void imx_set_async_mode(void) -{ - adjust_cr(CR_920T_CLOCK_MODE, CR_920T_ASYNC_MODE); -} - -static void imx_set_fastbus_mode(void) -{ - adjust_cr(CR_920T_CLOCK_MODE, CR_920T_FASTBUS_MODE); -} - -static void imx_set_mpctl0(u32 mpctl0) -{ - unsigned long flags; - - if (mpctl0 == 0) { - local_irq_save(flags); - CSCR &= ~CSCR_MPEN; - local_irq_restore(flags); - return; - } - - local_irq_save(flags); - MPCTL0 = mpctl0; - CSCR |= CSCR_MPEN; - local_irq_restore(flags); -} - -/** - * imx_compute_mpctl - compute new PLL parameters - * @new_mpctl: pointer to location assigned by new PLL control register value - * @cur_mpctl: current PLL control register parameters - * @f_ref: reference source frequency Hz - * @freq: required frequency in Hz - * @relation: is one of %CPUFREQ_RELATION_L (supremum) - * and %CPUFREQ_RELATION_H (infimum) - */ -long imx_compute_mpctl(u32 *new_mpctl, u32 cur_mpctl, u32 f_ref, unsigned long freq, int relation) -{ - u32 mfi; - u32 mfn; - u32 mfd; - u32 pd; - unsigned long long ll; - long l; - long quot; - - /* Fdppl=2*Fref*(MFI+MFN/(MFD+1))/(PD+1) */ - /* PD=<0,15>, MFD=<1,1023>, MFI=<5,15> MFN=<0,1022> */ - - if (cur_mpctl) { - mfd = ((cur_mpctl >> 16) & 0x3ff) + 1; - pd = ((cur_mpctl >> 26) & 0xf) + 1; - } else { - pd=2; mfd=313; - } - - /* pd=2; mfd=313; mfi=8; mfn=183; */ - /* (MFI+MFN/(MFD)) = Fdppl / (2*Fref) * (PD); */ - - quot = (f_ref + (1 << 9)) >> 10; - l = (freq * pd + quot) / (2 * quot); - mfi = l >> 10; - mfn = ((l & ((1 << 10) - 1)) * mfd + (1 << 9)) >> 10; - - mfd -= 1; - pd -= 1; - - *new_mpctl = ((mfi & 0xf) << 10) | (mfn & 0x3ff) | ((mfd & 0x3ff) << 16) - | ((pd & 0xf) << 26); - - ll = 2 * (unsigned long long)f_ref * ( (mfi<<16) + (mfn<<16) / (mfd+1) ); - quot = (pd+1) * (1<<16); - ll += quot / 2; - do_div(ll, quot); - freq = ll; - - pr_debug(KERN_DEBUG "imx: new PLL parameters pd=%d mfd=%d mfi=%d mfn=%d, freq=%ld\n", - pd, mfd, mfi, mfn, freq); - - return freq; -} - - -static int imx_verify_speed(struct cpufreq_policy *policy) -{ - if (policy->cpu != 0) - return -EINVAL; - - cpufreq_verify_within_limits(policy, policy->cpuinfo.min_freq, policy->cpuinfo.max_freq); - - return 0; -} - -static unsigned int imx_get_speed(unsigned int cpu) -{ - unsigned int freq; - unsigned int cr; - unsigned int cscr; - unsigned int bclk_div; - - if (cpu) - return 0; - - cscr = CSCR; - bclk_div = __mfld2val(CSCR_BCLK_DIV, cscr) + 1; - cr = get_cr(); - - if((cr & CR_920T_CLOCK_MODE) == CR_920T_FASTBUS_MODE) { - freq = clk_get_rate(system_clk); - freq = (freq + bclk_div/2) / bclk_div; - } else { - freq = clk_get_rate(mcu_clk); - if (cscr & CSCR_MPU_PRESC) - freq /= 2; - } - - freq = (freq + 500) / 1000; - - return freq; -} - -static int imx_set_target(struct cpufreq_policy *policy, - unsigned int target_freq, - unsigned int relation) -{ - struct cpufreq_freqs freqs; - u32 mpctl0 = 0; - u32 cscr; - unsigned long flags; - long freq; - long sysclk; - unsigned int bclk_div = bclk_div_at_boot; - - /* - * Some governors do not respects CPU and policy lower limits - * which leads to bad things (division by zero etc), ensure - * that such things do not happen. - */ - if(target_freq < policy->cpuinfo.min_freq) - target_freq = policy->cpuinfo.min_freq; - - if(target_freq < policy->min) - target_freq = policy->min; - - freq = target_freq * 1000; - - pr_debug(KERN_DEBUG "imx: requested frequency %ld Hz, mpctl0 at boot 0x%08x\n", - freq, mpctl0_at_boot); - - sysclk = clk_get_rate(system_clk); - - if (freq > sysclk / bclk_div_at_boot + 1000000) { - freq = imx_compute_mpctl(&mpctl0, mpctl0_at_boot, CLK32 * 512, freq, relation); - if (freq < 0) { - printk(KERN_WARNING "imx: target frequency %ld Hz cannot be set\n", freq); - return -EINVAL; - } - } else { - if(freq + 1000 < sysclk) { - if (relation == CPUFREQ_RELATION_L) - bclk_div = (sysclk - 1000) / freq; - else - bclk_div = (sysclk + freq + 1000) / freq; - - if(bclk_div > 16) - bclk_div = 16; - if(bclk_div < bclk_div_at_boot) - bclk_div = bclk_div_at_boot; - } - freq = (sysclk + bclk_div / 2) / bclk_div; - } - - freqs.old = imx_get_speed(0); - freqs.new = (freq + 500) / 1000; - freqs.cpu = 0; - freqs.flags = 0; - - cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); - - local_irq_save(flags); - - imx_set_fastbus_mode(); - - imx_set_mpctl0(mpctl0); - - cscr = CSCR; - cscr &= ~CSCR_BCLK_DIV; - cscr |= __val2mfld(CSCR_BCLK_DIV, bclk_div - 1); - CSCR = cscr; - - if(mpctl0) { - CSCR |= CSCR_MPLL_RESTART; - - /* Wait until MPLL is stabilized */ - while( CSCR & CSCR_MPLL_RESTART ); - - imx_set_async_mode(); - } - - local_irq_restore(flags); - - cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); - - pr_debug(KERN_INFO "imx: set frequency %ld Hz, running from %s\n", - freq, mpctl0? "MPLL": "SPLL"); - - return 0; -} - -static int __init imx_cpufreq_driver_init(struct cpufreq_policy *policy) -{ - printk(KERN_INFO "i.MX cpu freq change driver v1.0\n"); - - if (policy->cpu != 0) - return -EINVAL; - - policy->cur = policy->min = policy->max = imx_get_speed(0); - policy->cpuinfo.min_freq = 8000; - policy->cpuinfo.max_freq = 200000; - /* Manual states, that PLL stabilizes in two CLK32 periods */ - policy->cpuinfo.transition_latency = 4 * 1000000000LL / CLK32; - return 0; -} - -static struct cpufreq_driver imx_driver = { - .flags = CPUFREQ_STICKY, - .verify = imx_verify_speed, - .target = imx_set_target, - .get = imx_get_speed, - .init = imx_cpufreq_driver_init, - .name = "imx", -}; - -static int __init imx_cpufreq_init(void) -{ - bclk_div_at_boot = __mfld2val(CSCR_BCLK_DIV, CSCR) + 1; - mpctl0_at_boot = 0; - - system_clk = clk_get(NULL, "system_clk"); - if (IS_ERR(system_clk)) - return PTR_ERR(system_clk); - - mcu_clk = clk_get(NULL, "mcu_clk"); - if (IS_ERR(mcu_clk)) { - clk_put(system_clk); - return PTR_ERR(mcu_clk); - } - - if((CSCR & CSCR_MPEN) && - ((get_cr() & CR_920T_CLOCK_MODE) != CR_920T_FASTBUS_MODE)) - mpctl0_at_boot = MPCTL0; - - return cpufreq_register_driver(&imx_driver); -} - -arch_initcall(imx_cpufreq_init); - diff --git a/arch/arm/mach-imx/dma.c b/arch/arm/mach-imx/dma.c deleted file mode 100644 index 1536583eece..00000000000 --- a/arch/arm/mach-imx/dma.c +++ /dev/null @@ -1,597 +0,0 @@ -/* - * linux/arch/arm/mach-imx/dma.c - * - * imx DMA registration and IRQ dispatching - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * 2004-03-03 Sascha Hauer <sascha@saschahauer.de> - * initial version heavily inspired by - * linux/arch/arm/mach-pxa/dma.c - * - * 2005-04-17 Pavel Pisa <pisa@cmp.felk.cvut.cz> - * Changed to support scatter gather DMA - * by taking Russell's code from RiscPC - * - * 2006-05-31 Pavel Pisa <pisa@cmp.felk.cvut.cz> - * Corrected error handling code. - * - */ - -#undef DEBUG - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/interrupt.h> -#include <linux/errno.h> - -#include <asm/scatterlist.h> -#include <asm/system.h> -#include <asm/irq.h> -#include <mach/hardware.h> -#include <mach/dma.h> -#include <mach/imx-dma.h> - -struct imx_dma_channel imx_dma_channels[IMX_DMA_CHANNELS]; - -/* - * imx_dma_sg_next - prepare next chunk for scatter-gather DMA emulation - * @dma_ch: i.MX DMA channel number - * @lastcount: number of bytes transferred during last transfer - * - * Functions prepares DMA controller for next sg data chunk transfer. - * The @lastcount argument informs function about number of bytes transferred - * during last block. Zero value can be used for @lastcount to setup DMA - * for the first chunk. - */ -static inline int imx_dma_sg_next(imx_dmach_t dma_ch, unsigned int lastcount) -{ - struct imx_dma_channel *imxdma = &imx_dma_channels[dma_ch]; - unsigned int nextcount; - unsigned int nextaddr; - - if (!imxdma->name) { - printk(KERN_CRIT "%s: called for not allocated channel %d\n", - __func__, dma_ch); - return 0; - } - - imxdma->resbytes -= lastcount; - - if (!imxdma->sg) { - pr_debug("imxdma%d: no sg data\n", dma_ch); - return 0; - } - - imxdma->sgbc += lastcount; - if ((imxdma->sgbc >= imxdma->sg->length) || !imxdma->resbytes) { - if ((imxdma->sgcount <= 1) || !imxdma->resbytes) { - pr_debug("imxdma%d: sg transfer limit reached\n", - dma_ch); - imxdma->sgcount=0; - imxdma->sg = NULL; - return 0; - } else { - imxdma->sgcount--; - imxdma->sg++; - imxdma->sgbc = 0; - } - } - nextcount = imxdma->sg->length - imxdma->sgbc; - nextaddr = imxdma->sg->dma_address + imxdma->sgbc; - - if(imxdma->resbytes < nextcount) - nextcount = imxdma->resbytes; - - if ((imxdma->dma_mode & DMA_MODE_MASK) == DMA_MODE_READ) - DAR(dma_ch) = nextaddr; - else - SAR(dma_ch) = nextaddr; - - CNTR(dma_ch) = nextcount; - pr_debug("imxdma%d: next sg chunk dst 0x%08x, src 0x%08x, size 0x%08x\n", - dma_ch, DAR(dma_ch), SAR(dma_ch), CNTR(dma_ch)); - - return nextcount; -} - -/* - * imx_dma_setup_sg_base - scatter-gather DMA emulation - * @dma_ch: i.MX DMA channel number - * @sg: pointer to the scatter-gather list/vector - * @sgcount: scatter-gather list hungs count - * - * Functions sets up i.MX DMA state for emulated scatter-gather transfer - * and sets up channel registers to be ready for the first chunk - */ -static int -imx_dma_setup_sg_base(imx_dmach_t dma_ch, - struct scatterlist *sg, unsigned int sgcount) -{ - struct imx_dma_channel *imxdma = &imx_dma_channels[dma_ch]; - - imxdma->sg = sg; - imxdma->sgcount = sgcount; - imxdma->sgbc = 0; - return imx_dma_sg_next(dma_ch, 0); -} - -/** - * imx_dma_setup_single - setup i.MX DMA channel for linear memory to/from device transfer - * @dma_ch: i.MX DMA channel number - * @dma_address: the DMA/physical memory address of the linear data block - * to transfer - * @dma_length: length of the data block in bytes - * @dev_addr: physical device port address - * @dmamode: DMA transfer mode, %DMA_MODE_READ from the device to the memory - * or %DMA_MODE_WRITE from memory to the device - * - * The function setups DMA channel source and destination addresses for transfer - * specified by provided parameters. The scatter-gather emulation is disabled, - * because linear data block - * form the physical address range is transferred. - * Return value: if incorrect parameters are provided -%EINVAL. - * Zero indicates success. - */ -int -imx_dma_setup_single(imx_dmach_t dma_ch, dma_addr_t dma_address, - unsigned int dma_length, unsigned int dev_addr, - unsigned int dmamode) -{ - struct imx_dma_channel *imxdma = &imx_dma_channels[dma_ch]; - - imxdma->sg = NULL; - imxdma->sgcount = 0; - imxdma->dma_mode = dmamode; - imxdma->resbytes = dma_length; - - if (!dma_address) { - printk(KERN_ERR "imxdma%d: imx_dma_setup_single null address\n", - dma_ch); - return -EINVAL; - } - - if (!dma_length) { - printk(KERN_ERR "imxdma%d: imx_dma_setup_single zero length\n", - dma_ch); - return -EINVAL; - } - - if ((dmamode & DMA_MODE_MASK) == DMA_MODE_READ) { - pr_debug("imxdma%d: mx_dma_setup_single2dev dma_addressg=0x%08x dma_length=%d dev_addr=0x%08x for read\n", - dma_ch, (unsigned int)dma_address, dma_length, - dev_addr); - SAR(dma_ch) = dev_addr; - DAR(dma_ch) = (unsigned int)dma_address; - } else if ((dmamode & DMA_MODE_MASK) == DMA_MODE_WRITE) { - pr_debug("imxdma%d: mx_dma_setup_single2dev dma_addressg=0x%08x dma_length=%d dev_addr=0x%08x for write\n", - dma_ch, (unsigned int)dma_address, dma_length, - dev_addr); - SAR(dma_ch) = (unsigned int)dma_address; - DAR(dma_ch) = dev_addr; - } else { - printk(KERN_ERR "imxdma%d: imx_dma_setup_single bad dmamode\n", - dma_ch); - return -EINVAL; - } - - CNTR(dma_ch) = dma_length; - - return 0; -} - -/** - * imx_dma_setup_sg - setup i.MX DMA channel SG list to/from device transfer - * @dma_ch: i.MX DMA channel number - * @sg: pointer to the scatter-gather list/vector - * @sgcount: scatter-gather list hungs count - * @dma_length: total length of the transfer request in bytes - * @dev_addr: physical device port address - * @dmamode: DMA transfer mode, %DMA_MODE_READ from the device to the memory - * or %DMA_MODE_WRITE from memory to the device - * - * The function sets up DMA channel state and registers to be ready for transfer - * specified by provided parameters. The scatter-gather emulation is set up - * according to the parameters. - * - * The full preparation of the transfer requires setup of more register - * by the caller before imx_dma_enable() can be called. - * - * %BLR(dma_ch) holds transfer burst length in bytes, 0 means 64 bytes - * - * %RSSR(dma_ch) has to be set to the DMA request line source %DMA_REQ_xxx - * - * %CCR(dma_ch) has to specify transfer parameters, the next settings is typical - * for linear or simple scatter-gather transfers if %DMA_MODE_READ is specified - * - * %CCR_DMOD_LINEAR | %CCR_DSIZ_32 | %CCR_SMOD_FIFO | %CCR_SSIZ_x - * - * The typical setup for %DMA_MODE_WRITE is specified by next options combination - * - * %CCR_SMOD_LINEAR | %CCR_SSIZ_32 | %CCR_DMOD_FIFO | %CCR_DSIZ_x - * - * Be careful here and do not mistakenly mix source and target device - * port sizes constants, they are really different: - * %CCR_SSIZ_8, %CCR_SSIZ_16, %CCR_SSIZ_32, - * %CCR_DSIZ_8, %CCR_DSIZ_16, %CCR_DSIZ_32 - * - * Return value: if incorrect parameters are provided -%EINVAL. - * Zero indicates success. - */ -int -imx_dma_setup_sg(imx_dmach_t dma_ch, - struct scatterlist *sg, unsigned int sgcount, unsigned int dma_length, - unsigned int dev_addr, unsigned int dmamode) -{ - int res; - struct imx_dma_channel *imxdma = &imx_dma_channels[dma_ch]; - - imxdma->sg = NULL; - imxdma->sgcount = 0; - imxdma->dma_mode = dmamode; - imxdma->resbytes = dma_length; - - if (!sg || !sgcount) { - printk(KERN_ERR "imxdma%d: imx_dma_setup_sg epty sg list\n", - dma_ch); - return -EINVAL; - } - - if (!sg->length) { - printk(KERN_ERR "imxdma%d: imx_dma_setup_sg zero length\n", - dma_ch); - return -EINVAL; - } - - if ((dmamode & DMA_MODE_MASK) == DMA_MODE_READ) { - pr_debug("imxdma%d: mx_dma_setup_sg2dev sg=%p sgcount=%d total length=%d dev_addr=0x%08x for read\n", - dma_ch, sg, sgcount, dma_length, dev_addr); - SAR(dma_ch) = dev_addr; - } else if ((dmamode & DMA_MODE_MASK) == DMA_MODE_WRITE) { - pr_debug("imxdma%d: mx_dma_setup_sg2dev sg=%p sgcount=%d total length=%d dev_addr=0x%08x for write\n", - dma_ch, sg, sgcount, dma_length, dev_addr); - DAR(dma_ch) = dev_addr; - } else { - printk(KERN_ERR "imxdma%d: imx_dma_setup_sg bad dmamode\n", - dma_ch); - return -EINVAL; - } - - res = imx_dma_setup_sg_base(dma_ch, sg, sgcount); - if (res <= 0) { - printk(KERN_ERR "imxdma%d: no sg chunk ready\n", dma_ch); - return -EINVAL; - } - - return 0; -} - -/** - * imx_dma_setup_handlers - setup i.MX DMA channel end and error notification handlers - * @dma_ch: i.MX DMA channel number - * @irq_handler: the pointer to the function called if the transfer - * ends successfully - * @err_handler: the pointer to the function called if the premature - * end caused by error occurs - * @data: user specified value to be passed to the handlers - */ -int -imx_dma_setup_handlers(imx_dmach_t dma_ch, - void (*irq_handler) (int, void *), - void (*err_handler) (int, void *, int), - void *data) -{ - struct imx_dma_channel *imxdma = &imx_dma_channels[dma_ch]; - unsigned long flags; - - if (!imxdma->name) { - printk(KERN_CRIT "%s: called for not allocated channel %d\n", - __func__, dma_ch); - return -ENODEV; - } - - local_irq_save(flags); - DISR = (1 << dma_ch); - imxdma->irq_handler = irq_handler; - imxdma->err_handler = err_handler; - imxdma->data = data; - local_irq_restore(flags); - return 0; -} - -/** - * imx_dma_enable - function to start i.MX DMA channel operation - * @dma_ch: i.MX DMA channel number - * - * The channel has to be allocated by driver through imx_dma_request() - * or imx_dma_request_by_prio() function. - * The transfer parameters has to be set to the channel registers through - * call of the imx_dma_setup_single() or imx_dma_setup_sg() function - * and registers %BLR(dma_ch), %RSSR(dma_ch) and %CCR(dma_ch) has to - * be set prior this function call by the channel user. - */ -void imx_dma_enable(imx_dmach_t dma_ch) -{ - struct imx_dma_channel *imxdma = &imx_dma_channels[dma_ch]; - unsigned long flags; - - pr_debug("imxdma%d: imx_dma_enable\n", dma_ch); - - if (!imxdma->name) { - printk(KERN_CRIT "%s: called for not allocated channel %d\n", - __func__, dma_ch); - return; - } - - local_irq_save(flags); - DISR = (1 << dma_ch); - DIMR &= ~(1 << dma_ch); - CCR(dma_ch) |= CCR_CEN; - local_irq_restore(flags); -} - -/** - * imx_dma_disable - stop, finish i.MX DMA channel operatin - * @dma_ch: i.MX DMA channel number - */ -void imx_dma_disable(imx_dmach_t dma_ch) -{ - unsigned long flags; - - pr_debug("imxdma%d: imx_dma_disable\n", dma_ch); - - local_irq_save(flags); - DIMR |= (1 << dma_ch); - CCR(dma_ch) &= ~CCR_CEN; - DISR = (1 << dma_ch); - local_irq_restore(flags); -} - -/** - * imx_dma_request - request/allocate specified channel number - * @dma_ch: i.MX DMA channel number - * @name: the driver/caller own non-%NULL identification - */ -int imx_dma_request(imx_dmach_t dma_ch, const char *name) -{ - struct imx_dma_channel *imxdma = &imx_dma_channels[dma_ch]; - unsigned long flags; - - /* basic sanity checks */ - if (!name) - return -EINVAL; - - if (dma_ch >= IMX_DMA_CHANNELS) { - printk(KERN_CRIT "%s: called for non-existed channel %d\n", - __func__, dma_ch); - return -EINVAL; - } - - local_irq_save(flags); - if (imxdma->name) { - local_irq_restore(flags); - return -ENODEV; - } - - imxdma->name = name; - imxdma->irq_handler = NULL; - imxdma->err_handler = NULL; - imxdma->data = NULL; - imxdma->sg = NULL; - local_irq_restore(flags); - return 0; -} - -/** - * imx_dma_free - release previously acquired channel - * @dma_ch: i.MX DMA channel number - */ -void imx_dma_free(imx_dmach_t dma_ch) -{ - unsigned long flags; - struct imx_dma_channel *imxdma = &imx_dma_channels[dma_ch]; - - if (!imxdma->name) { - printk(KERN_CRIT - "%s: trying to free channel %d which is already freed\n", - __func__, dma_ch); - return; - } - - local_irq_save(flags); - /* Disable interrupts */ - DIMR |= (1 << dma_ch); - CCR(dma_ch) &= ~CCR_CEN; - imxdma->name = NULL; - local_irq_restore(flags); -} - -/** - * imx_dma_request_by_prio - find and request some of free channels best suiting requested priority - * @name: the driver/caller own non-%NULL identification - * @prio: one of the hardware distinguished priority level: - * %DMA_PRIO_HIGH, %DMA_PRIO_MEDIUM, %DMA_PRIO_LOW - * - * This function tries to find free channel in the specified priority group - * if the priority cannot be achieved it tries to look for free channel - * in the higher and then even lower priority groups. - * - * Return value: If there is no free channel to allocate, -%ENODEV is returned. - * On successful allocation channel is returned. - */ -imx_dmach_t imx_dma_request_by_prio(const char *name, imx_dma_prio prio) -{ - int i; - int best; - - switch (prio) { - case (DMA_PRIO_HIGH): - best = 8; - break; - case (DMA_PRIO_MEDIUM): - best = 4; - break; - case (DMA_PRIO_LOW): - default: - best = 0; - break; - } - - for (i = best; i < IMX_DMA_CHANNELS; i++) { - if (!imx_dma_request(i, name)) { - return i; - } - } - - for (i = best - 1; i >= 0; i--) { - if (!imx_dma_request(i, name)) { - return i; - } - } - - printk(KERN_ERR "%s: no free DMA channel found\n", __func__); - - return -ENODEV; -} - -static irqreturn_t dma_err_handler(int irq, void *dev_id) -{ - int i, disr = DISR; - struct imx_dma_channel *channel; - unsigned int err_mask = DBTOSR | DRTOSR | DSESR | DBOSR; - int errcode; - - DISR = disr & err_mask; - for (i = 0; i < IMX_DMA_CHANNELS; i++) { - if(!(err_mask & (1 << i))) - continue; - channel = &imx_dma_channels[i]; - errcode = 0; - - if (DBTOSR & (1 << i)) { - DBTOSR = (1 << i); - errcode |= IMX_DMA_ERR_BURST; - } - if (DRTOSR & (1 << i)) { - DRTOSR = (1 << i); - errcode |= IMX_DMA_ERR_REQUEST; - } - if (DSESR & (1 << i)) { - DSESR = (1 << i); - errcode |= IMX_DMA_ERR_TRANSFER; - } - if (DBOSR & (1 << i)) { - DBOSR = (1 << i); - errcode |= IMX_DMA_ERR_BUFFER; - } - - /* - * The cleaning of @sg field would be questionable - * there, because its value can help to compute - * remaining/transferred bytes count in the handler - */ - /*imx_dma_channels[i].sg = NULL;*/ - - if (channel->name && channel->err_handler) { - channel->err_handler(i, channel->data, errcode); - continue; - } - - imx_dma_channels[i].sg = NULL; - - printk(KERN_WARNING - "DMA timeout on channel %d (%s) -%s%s%s%s\n", - i, channel->name, - errcode&IMX_DMA_ERR_BURST? " burst":"", - errcode&IMX_DMA_ERR_REQUEST? " request":"", - errcode&IMX_DMA_ERR_TRANSFER? " transfer":"", - errcode&IMX_DMA_ERR_BUFFER? " buffer":""); - } - return IRQ_HANDLED; -} - -static irqreturn_t dma_irq_handler(int irq, void *dev_id) -{ - int i, disr = DISR; - - pr_debug("imxdma: dma_irq_handler called, disr=0x%08x\n", - disr); - - DISR = disr; - for (i = 0; i < IMX_DMA_CHANNELS; i++) { - if (disr & (1 << i)) { - struct imx_dma_channel *channel = &imx_dma_channels[i]; - if (channel->name) { - if (imx_dma_sg_next(i, CNTR(i))) { - CCR(i) &= ~CCR_CEN; - mb(); - CCR(i) |= CCR_CEN; - } else { - if (channel->irq_handler) - channel->irq_handler(i, - channel->data); - } - } else { - /* - * IRQ for an unregistered DMA channel: - * let's clear the interrupts and disable it. - */ - printk(KERN_WARNING - "spurious IRQ for DMA channel %d\n", i); - } - } - } - return IRQ_HANDLED; -} - -static int __init imx_dma_init(void) -{ - int ret; - int i; - - /* reset DMA module */ - DCR = DCR_DRST; - - ret = request_irq(DMA_INT, dma_irq_handler, 0, "DMA", NULL); - if (ret) { - printk(KERN_CRIT "Wow! Can't register IRQ for DMA\n"); - return ret; - } - - ret = request_irq(DMA_ERR, dma_err_handler, 0, "DMA", NULL); - if (ret) { - printk(KERN_CRIT "Wow! Can't register ERRIRQ for DMA\n"); - free_irq(DMA_INT, NULL); - } - - /* enable DMA module */ - DCR = DCR_DEN; - - /* clear all interrupts */ - DISR = (1 << IMX_DMA_CHANNELS) - 1; - - /* enable interrupts */ - DIMR = (1 << IMX_DMA_CHANNELS) - 1; - - for (i = 0; i < IMX_DMA_CHANNELS; i++) { - imx_dma_channels[i].sg = NULL; - imx_dma_channels[i].dma_num = i; - } - - return ret; -} - -arch_initcall(imx_dma_init); - -EXPORT_SYMBOL(imx_dma_setup_single); -EXPORT_SYMBOL(imx_dma_setup_sg); -EXPORT_SYMBOL(imx_dma_setup_handlers); -EXPORT_SYMBOL(imx_dma_enable); -EXPORT_SYMBOL(imx_dma_disable); -EXPORT_SYMBOL(imx_dma_request); -EXPORT_SYMBOL(imx_dma_free); -EXPORT_SYMBOL(imx_dma_request_by_prio); -EXPORT_SYMBOL(imx_dma_channels); diff --git a/arch/arm/mach-imx/generic.c b/arch/arm/mach-imx/generic.c deleted file mode 100644 index 05f1739ee12..00000000000 --- a/arch/arm/mach-imx/generic.c +++ /dev/null @@ -1,271 +0,0 @@ -/* - * arch/arm/mach-imx/generic.c - * - * author: Sascha Hauer - * Created: april 20th, 2004 - * Copyright: Synertronixx GmbH - * - * Common code for i.MX machines - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ -#include <linux/platform_device.h> -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/string.h> - -#include <asm/errno.h> -#include <mach/hardware.h> -#include <mach/imx-regs.h> - -#include <asm/mach/map.h> -#include <mach/mmc.h> -#include <mach/gpio.h> - -unsigned long imx_gpio_alloc_map[(GPIO_PORT_MAX + 1) * 32 / BITS_PER_LONG]; - -void imx_gpio_mode(int gpio_mode) -{ - unsigned int pin = gpio_mode & GPIO_PIN_MASK; - unsigned int port = (gpio_mode & GPIO_PORT_MASK) >> GPIO_PORT_SHIFT; - unsigned int ocr = (gpio_mode & GPIO_OCR_MASK) >> GPIO_OCR_SHIFT; - unsigned int tmp; - - /* Pullup enable */ - if(gpio_mode & GPIO_PUEN) - PUEN(port) |= (1<<pin); - else - PUEN(port) &= ~(1<<pin); - - /* Data direction */ - if(gpio_mode & GPIO_OUT) - DDIR(port) |= 1<<pin; - else - DDIR(port) &= ~(1<<pin); - - /* Primary / alternate function */ - if(gpio_mode & GPIO_AF) - GPR(port) |= (1<<pin); - else - GPR(port) &= ~(1<<pin); - - /* use as gpio? */ - if(gpio_mode & GPIO_GIUS) - GIUS(port) |= (1<<pin); - else - GIUS(port) &= ~(1<<pin); - - /* Output / input configuration */ - /* FIXME: I'm not very sure about OCR and ICONF, someone - * should have a look over it - */ - if(pin<16) { - tmp = OCR1(port); - tmp &= ~( 3<<(pin*2)); - tmp |= (ocr << (pin*2)); - OCR1(port) = tmp; - - ICONFA1(port) &= ~( 3<<(pin*2)); - ICONFA1(port) |= ((gpio_mode >> GPIO_AOUT_SHIFT) & 3) << (pin * 2); - ICONFB1(port) &= ~( 3<<(pin*2)); - ICONFB1(port) |= ((gpio_mode >> GPIO_BOUT_SHIFT) & 3) << (pin * 2); - } else { - tmp = OCR2(port); - tmp &= ~( 3<<((pin-16)*2)); - tmp |= (ocr << ((pin-16)*2)); - OCR2(port) = tmp; - - ICONFA2(port) &= ~( 3<<((pin-16)*2)); - ICONFA2(port) |= ((gpio_mode >> GPIO_AOUT_SHIFT) & 3) << ((pin-16) * 2); - ICONFB2(port) &= ~( 3<<((pin-16)*2)); - ICONFB2(port) |= ((gpio_mode >> GPIO_BOUT_SHIFT) & 3) << ((pin-16) * 2); - } -} - -EXPORT_SYMBOL(imx_gpio_mode); - -int imx_gpio_request(unsigned gpio, const char *label) -{ - if(gpio >= (GPIO_PORT_MAX + 1) * 32) { - printk(KERN_ERR "imx_gpio: Attempt to request nonexistent GPIO %d for \"%s\"\n", - gpio, label ? label : "?"); - return -EINVAL; - } - - if(test_and_set_bit(gpio, imx_gpio_alloc_map)) { - printk(KERN_ERR "imx_gpio: GPIO %d already used. Allocation for \"%s\" failed\n", - gpio, label ? label : "?"); - return -EBUSY; - } - - return 0; -} - -EXPORT_SYMBOL(imx_gpio_request); - -void imx_gpio_free(unsigned gpio) -{ - if(gpio >= (GPIO_PORT_MAX + 1) * 32) - return; - - clear_bit(gpio, imx_gpio_alloc_map); -} - -EXPORT_SYMBOL(imx_gpio_free); - -int imx_gpio_direction_input(unsigned gpio) -{ - imx_gpio_mode(gpio | GPIO_IN | GPIO_GIUS | GPIO_DR); - return 0; -} - -EXPORT_SYMBOL(imx_gpio_direction_input); - -int imx_gpio_direction_output(unsigned gpio, int value) -{ - imx_gpio_set_value(gpio, value); - imx_gpio_mode(gpio | GPIO_OUT | GPIO_GIUS | GPIO_DR); - return 0; -} - -EXPORT_SYMBOL(imx_gpio_direction_output); - -int imx_gpio_setup_multiple_pins(const int *pin_list, unsigned count, - int alloc_mode, const char *label) -{ - const int *p = pin_list; - int i; - unsigned gpio; - unsigned mode; - - for (i = 0; i < count; i++) { - gpio = *p & (GPIO_PIN_MASK | GPIO_PORT_MASK); - mode = *p & ~(GPIO_PIN_MASK | GPIO_PORT_MASK); - - if (gpio >= (GPIO_PORT_MAX + 1) * 32) - goto setup_error; - - if (alloc_mode & IMX_GPIO_ALLOC_MODE_RELEASE) - imx_gpio_free(gpio); - else if (!(alloc_mode & IMX_GPIO_ALLOC_MODE_NO_ALLOC)) - if (imx_gpio_request(gpio, label)) - if (!(alloc_mode & IMX_GPIO_ALLOC_MODE_TRY_ALLOC)) - goto setup_error; - - if (!(alloc_mode & (IMX_GPIO_ALLOC_MODE_ALLOC_ONLY | - IMX_GPIO_ALLOC_MODE_RELEASE))) - imx_gpio_mode(gpio | mode); - - p++; - } - return 0; - -setup_error: - if(alloc_mode & (IMX_GPIO_ALLOC_MODE_NO_ALLOC | - IMX_GPIO_ALLOC_MODE_TRY_ALLOC)) - return -EINVAL; - - while (p != pin_list) { - p--; - gpio = *p & (GPIO_PIN_MASK | GPIO_PORT_MASK); - imx_gpio_free(gpio); - } - - return -EINVAL; -} - -EXPORT_SYMBOL(imx_gpio_setup_multiple_pins); - -void __imx_gpio_set_value(unsigned gpio, int value) -{ - imx_gpio_set_value_inline(gpio, value); -} - -EXPORT_SYMBOL(__imx_gpio_set_value); - -int imx_gpio_to_irq(unsigned gpio) -{ - return IRQ_GPIOA(0) + gpio; -} - -EXPORT_SYMBOL(imx_gpio_to_irq); - -int imx_irq_to_gpio(unsigned irq) -{ - if (irq < IRQ_GPIOA(0)) - return -EINVAL; - return irq - IRQ_GPIOA(0); -} - -EXPORT_SYMBOL(imx_irq_to_gpio); - -static struct resource imx_mmc_resources[] = { - [0] = { - .start = 0x00214000, - .end = 0x002140FF, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = (SDHC_INT), - .end = (SDHC_INT), - .flags = IORESOURCE_IRQ, - }, -}; - -static u64 imxmmmc_dmamask = 0xffffffffUL; - -static struct platform_device imx_mmc_device = { - .name = "imx-mmc", - .id = 0, - .dev = { - .dma_mask = &imxmmmc_dmamask, - .coherent_dma_mask = 0xffffffff, - }, - .num_resources = ARRAY_SIZE(imx_mmc_resources), - .resource = imx_mmc_resources, -}; - -void __init imx_set_mmc_info(struct imxmmc_platform_data *info) -{ - imx_mmc_device.dev.platform_data = info; -} - -static struct platform_device *devices[] __initdata = { - &imx_mmc_device, -}; - -static struct map_desc imx_io_desc[] __initdata = { - { - .virtual = IMX_IO_BASE, - .pfn = __phys_to_pfn(IMX_IO_PHYS), - .length = IMX_IO_SIZE, - .type = MT_DEVICE - } -}; - -void __init -imx_map_io(void) -{ - iotable_init(imx_io_desc, ARRAY_SIZE(imx_io_desc)); -} - -static int __init imx_init(void) -{ - return platform_add_devices(devices, ARRAY_SIZE(devices)); -} - -subsys_initcall(imx_init); diff --git a/arch/arm/mach-imx/generic.h b/arch/arm/mach-imx/generic.h deleted file mode 100644 index e91003e4bef..00000000000 --- a/arch/arm/mach-imx/generic.h +++ /dev/null @@ -1,16 +0,0 @@ -/* - * linux/arch/arm/mach-imx/generic.h - * - * Author: Sascha Hauer <sascha@saschahauer.de> - * Copyright: Synertronixx GmbH - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -extern void __init imx_map_io(void); -extern void __init imx_init_irq(void); - -struct sys_timer; -extern struct sys_timer imx_timer; diff --git a/arch/arm/mach-imx/include/mach/debug-macro.S b/arch/arm/mach-imx/include/mach/debug-macro.S deleted file mode 100644 index 87802bbfe63..00000000000 --- a/arch/arm/mach-imx/include/mach/debug-macro.S +++ /dev/null @@ -1,34 +0,0 @@ -/* arch/arm/mach-imx/include/mach/debug-macro.S - * - * Debugging macro include header - * - * Copyright (C) 1994-1999 Russell King - * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * -*/ - - .macro addruart,rx - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #0x00000000 @ physical - movne \rx, #0xe0000000 @ virtual - orreq \rx, \rx, #0x00200000 @ physical - orr \rx, \rx, #0x00006000 @ UART1 offset - .endm - - .macro senduart,rd,rx - str \rd, [\rx, #0x40] @ TXDATA - .endm - - .macro waituart,rd,rx - .endm - - .macro busyuart,rd,rx -1002: ldr \rd, [\rx, #0x98] @ SR2 - tst \rd, #1 << 3 @ TXDC - beq 1002b @ wait until transmit done - .endm diff --git a/arch/arm/mach-imx/include/mach/dma.h b/arch/arm/mach-imx/include/mach/dma.h deleted file mode 100644 index 621ff2c730f..00000000000 --- a/arch/arm/mach-imx/include/mach/dma.h +++ /dev/null @@ -1,56 +0,0 @@ -/* - * linux/include/asm-arm/imxads/dma.h - * - * Copyright (C) 1997,1998 Russell King - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_DMA_H -#define __ASM_ARCH_DMA_H - -typedef enum { - DMA_PRIO_HIGH = 0, - DMA_PRIO_MEDIUM = 1, - DMA_PRIO_LOW = 2 -} imx_dma_prio; - -#define DMA_REQ_UART3_T 2 -#define DMA_REQ_UART3_R 3 -#define DMA_REQ_SSI2_T 4 -#define DMA_REQ_SSI2_R 5 -#define DMA_REQ_CSI_STAT 6 -#define DMA_REQ_CSI_R 7 -#define DMA_REQ_MSHC 8 -#define DMA_REQ_DSPA_DCT_DOUT 9 -#define DMA_REQ_DSPA_DCT_DIN 10 -#define DMA_REQ_DSPA_MAC 11 -#define DMA_REQ_EXT 12 -#define DMA_REQ_SDHC 13 -#define DMA_REQ_SPI1_R 14 -#define DMA_REQ_SPI1_T 15 -#define DMA_REQ_SSI_T 16 -#define DMA_REQ_SSI_R 17 -#define DMA_REQ_ASP_DAC 18 -#define DMA_REQ_ASP_ADC 19 -#define DMA_REQ_USP_EP(x) (20+(x)) -#define DMA_REQ_SPI2_R 26 -#define DMA_REQ_SPI2_T 27 -#define DMA_REQ_UART2_T 28 -#define DMA_REQ_UART2_R 29 -#define DMA_REQ_UART1_T 30 -#define DMA_REQ_UART1_R 31 - -#endif /* _ASM_ARCH_DMA_H */ diff --git a/arch/arm/mach-imx/include/mach/entry-macro.S b/arch/arm/mach-imx/include/mach/entry-macro.S deleted file mode 100644 index e4db679f776..00000000000 --- a/arch/arm/mach-imx/include/mach/entry-macro.S +++ /dev/null @@ -1,32 +0,0 @@ -/* - * arch/arm/mach-imx/include/mach/entry-macro.S - * - * Low-level IRQ helper macros for iMX-based platforms - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - */ -#include <mach/hardware.h> - - .macro disable_fiq - .endm - - .macro get_irqnr_preamble, base, tmp - .endm - - .macro arch_ret_to_user, tmp1, tmp2 - .endm - -#define AITC_NIVECSR 0x40 - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \base, =IO_ADDRESS(IMX_AITC_BASE) - @ Load offset & priority of the highest priority - @ interrupt pending. - ldr \irqstat, [\base, #AITC_NIVECSR] - @ Shift off the priority leaving the offset or - @ "interrupt number", use arithmetic shift to - @ transform illegal source (0xffff) as -1 - mov \irqnr, \irqstat, asr #16 - adds \tmp, \irqnr, #1 - .endm diff --git a/arch/arm/mach-imx/include/mach/gpio.h b/arch/arm/mach-imx/include/mach/gpio.h deleted file mode 100644 index 6c2942f8292..00000000000 --- a/arch/arm/mach-imx/include/mach/gpio.h +++ /dev/null @@ -1,106 +0,0 @@ -#ifndef _IMX_GPIO_H - -#include <linux/kernel.h> -#include <mach/hardware.h> -#include <mach/imx-regs.h> - -#define IMX_GPIO_ALLOC_MODE_NORMAL 0 -#define IMX_GPIO_ALLOC_MODE_NO_ALLOC 1 -#define IMX_GPIO_ALLOC_MODE_TRY_ALLOC 2 -#define IMX_GPIO_ALLOC_MODE_ALLOC_ONLY 4 -#define IMX_GPIO_ALLOC_MODE_RELEASE 8 - -extern int imx_gpio_request(unsigned gpio, const char *label); - -extern void imx_gpio_free(unsigned gpio); - -extern int imx_gpio_setup_multiple_pins(const int *pin_list, unsigned count, - int alloc_mode, const char *label); - -extern int imx_gpio_direction_input(unsigned gpio); - -extern int imx_gpio_direction_output(unsigned gpio, int value); - -extern void __imx_gpio_set_value(unsigned gpio, int value); - -static inline int imx_gpio_get_value(unsigned gpio) -{ - return SSR(gpio >> GPIO_PORT_SHIFT) & (1 << (gpio & GPIO_PIN_MASK)); -} - -static inline void imx_gpio_set_value_inline(unsigned gpio, int value) -{ - unsigned long flags; - - raw_local_irq_save(flags); - if(value) - DR(gpio >> GPIO_PORT_SHIFT) |= (1 << (gpio & GPIO_PIN_MASK)); - else - DR(gpio >> GPIO_PORT_SHIFT) &= ~(1 << (gpio & GPIO_PIN_MASK)); - raw_local_irq_restore(flags); -} - -static inline void imx_gpio_set_value(unsigned gpio, int value) -{ - if(__builtin_constant_p(gpio)) - imx_gpio_set_value_inline(gpio, value); - else - __imx_gpio_set_value(gpio, value); -} - -extern int imx_gpio_to_irq(unsigned gpio); - -extern int imx_irq_to_gpio(unsigned irq); - -/*-------------------------------------------------------------------------*/ - -/* Wrappers for "new style" GPIO calls. These calls i.MX specific versions - * to allow future extension of GPIO logic. - */ - -static inline int gpio_request(unsigned gpio, const char *label) -{ - return imx_gpio_request(gpio, label); -} - -static inline void gpio_free(unsigned gpio) -{ - might_sleep(); - - imx_gpio_free(gpio); -} - -static inline int gpio_direction_input(unsigned gpio) -{ - return imx_gpio_direction_input(gpio); -} - -static inline int gpio_direction_output(unsigned gpio, int value) -{ - return imx_gpio_direction_output(gpio, value); -} - -static inline int gpio_get_value(unsigned gpio) -{ - return imx_gpio_get_value(gpio); -} - -static inline void gpio_set_value(unsigned gpio, int value) -{ - imx_gpio_set_value(gpio, value); -} - -#include <asm-generic/gpio.h> /* cansleep wrappers */ - -static inline int gpio_to_irq(unsigned gpio) -{ - return imx_gpio_to_irq(gpio); -} - -static inline int irq_to_gpio(unsigned irq) -{ - return imx_irq_to_gpio(irq); -} - - -#endif diff --git a/arch/arm/mach-imx/include/mach/hardware.h b/arch/arm/mach-imx/include/mach/hardware.h deleted file mode 100644 index c73e9e724c7..00000000000 --- a/arch/arm/mach-imx/include/mach/hardware.h +++ /dev/null @@ -1,91 +0,0 @@ -/* - * arch/arm/mach-imx/include/mach/hardware.h - * - * Copyright (C) 1999 ARM Limited. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#ifndef __ASM_ARCH_HARDWARE_H -#define __ASM_ARCH_HARDWARE_H - -#include <asm/sizes.h> -#include "imx-regs.h" - -#ifndef __ASSEMBLY__ -# define __REG(x) (*((volatile u32 *)IO_ADDRESS(x))) - -# define __REG2(x,y) (*(volatile u32 *)((u32)&__REG(x) + (y))) -#endif - -/* - * Memory map - */ - -#define IMX_IO_PHYS 0x00200000 -#define IMX_IO_SIZE 0x00100000 -#define IMX_IO_BASE 0xe0000000 - -#define IMX_CS0_PHYS 0x10000000 -#define IMX_CS0_SIZE 0x02000000 -#define IMX_CS0_VIRT 0xe8000000 - -#define IMX_CS1_PHYS 0x12000000 -#define IMX_CS1_SIZE 0x01000000 -#define IMX_CS1_VIRT 0xea000000 - -#define IMX_CS2_PHYS 0x13000000 -#define IMX_CS2_SIZE 0x01000000 -#define IMX_CS2_VIRT 0xeb000000 - -#define IMX_CS3_PHYS 0x14000000 -#define IMX_CS3_SIZE 0x01000000 -#define IMX_CS3_VIRT 0xec000000 - -#define IMX_CS4_PHYS 0x15000000 -#define IMX_CS4_SIZE 0x01000000 -#define IMX_CS4_VIRT 0xed000000 - -#define IMX_CS5_PHYS 0x16000000 -#define IMX_CS5_SIZE 0x01000000 -#define IMX_CS5_VIRT 0xee000000 - -#define IMX_FB_VIRT 0xF1000000 -#define IMX_FB_SIZE (256*1024) - -/* macro to get at IO space when running virtually */ -#define IO_ADDRESS(x) ((x) | IMX_IO_BASE) - -#ifndef __ASSEMBLY__ -/* - * Handy routine to set GPIO functions - */ -extern void imx_gpio_mode( int gpio_mode ); - -#endif - -#define MAXIRQNUM 62 -#define MAXFIQNUM 62 -#define MAXSWINUM 62 - -/* - * Use SDRAM for memory - */ -#define MEM_SIZE 0x01000000 - -#ifdef CONFIG_ARCH_MX1ADS -#include "mx1ads.h" -#endif - -#endif diff --git a/arch/arm/mach-imx/include/mach/imx-dma.h b/arch/arm/mach-imx/include/mach/imx-dma.h deleted file mode 100644 index bbe54df7f0d..00000000000 --- a/arch/arm/mach-imx/include/mach/imx-dma.h +++ /dev/null @@ -1,98 +0,0 @@ -/* - * linux/include/asm-arm/imxads/dma.h - * - * Copyright (C) 1997,1998 Russell King - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include <mach/dma.h> - -#ifndef __ASM_ARCH_IMX_DMA_H -#define __ASM_ARCH_IMX_DMA_H - -#define IMX_DMA_CHANNELS 11 - -/* - * struct imx_dma_channel - i.MX specific DMA extension - * @name: name specified by DMA client - * @irq_handler: client callback for end of transfer - * @err_handler: client callback for error condition - * @data: clients context data for callbacks - * @dma_mode: direction of the transfer %DMA_MODE_READ or %DMA_MODE_WRITE - * @sg: pointer to the actual read/written chunk for scatter-gather emulation - * @sgbc: counter of processed bytes in the actual read/written chunk - * @resbytes: total residual number of bytes to transfer - * (it can be lower or same as sum of SG mapped chunk sizes) - * @sgcount: number of chunks to be read/written - * - * Structure is used for IMX DMA processing. It would be probably good - * @struct dma_struct in the future for external interfacing and use - * @struct imx_dma_channel only as extension to it. - */ - -struct imx_dma_channel { - const char *name; - void (*irq_handler) (int, void *); - void (*err_handler) (int, void *, int errcode); - void *data; - unsigned int dma_mode; - struct scatterlist *sg; - unsigned int sgbc; - unsigned int sgcount; - unsigned int resbytes; - int dma_num; -}; - -extern struct imx_dma_channel imx_dma_channels[IMX_DMA_CHANNELS]; - -#define IMX_DMA_ERR_BURST 1 -#define IMX_DMA_ERR_REQUEST 2 -#define IMX_DMA_ERR_TRANSFER 4 -#define IMX_DMA_ERR_BUFFER 8 - -/* The type to distinguish channel numbers parameter from ordinal int type */ -typedef int imx_dmach_t; - -#define DMA_MODE_READ 0 -#define DMA_MODE_WRITE 1 -#define DMA_MODE_MASK 1 - -int -imx_dma_setup_single(imx_dmach_t dma_ch, dma_addr_t dma_address, - unsigned int dma_length, unsigned int dev_addr, unsigned int dmamode); - -int -imx_dma_setup_sg(imx_dmach_t dma_ch, - struct scatterlist *sg, unsigned int sgcount, unsigned int dma_length, - unsigned int dev_addr, unsigned int dmamode); - -int -imx_dma_setup_handlers(imx_dmach_t dma_ch, - void (*irq_handler) (int, void *), - void (*err_handler) (int, void *, int), void *data); - -void imx_dma_enable(imx_dmach_t dma_ch); - -void imx_dma_disable(imx_dmach_t dma_ch); - -int imx_dma_request(imx_dmach_t dma_ch, const char *name); - -void imx_dma_free(imx_dmach_t dma_ch); - -imx_dmach_t imx_dma_request_by_prio(const char *name, imx_dma_prio prio); - - -#endif /* _ASM_ARCH_IMX_DMA_H */ diff --git a/arch/arm/mach-imx/include/mach/imx-regs.h b/arch/arm/mach-imx/include/mach/imx-regs.h deleted file mode 100644 index 490297fc0e3..00000000000 --- a/arch/arm/mach-imx/include/mach/imx-regs.h +++ /dev/null @@ -1,376 +0,0 @@ -#ifndef _IMX_REGS_H -#define _IMX_REGS_H -/* ------------------------------------------------------------------------ - * Motorola IMX system registers - * ------------------------------------------------------------------------ - * - */ - -/* - * Register BASEs, based on OFFSETs - * - */ -#define IMX_AIPI1_BASE (0x00000 + IMX_IO_BASE) -#define IMX_WDT_BASE (0x01000 + IMX_IO_BASE) -#define IMX_TIM1_BASE (0x02000 + IMX_IO_BASE) -#define IMX_TIM2_BASE (0x03000 + IMX_IO_BASE) -#define IMX_RTC_BASE (0x04000 + IMX_IO_BASE) -#define IMX_LCDC_BASE (0x05000 + IMX_IO_BASE) -#define IMX_UART1_BASE (0x06000 + IMX_IO_BASE) -#define IMX_UART2_BASE (0x07000 + IMX_IO_BASE) -#define IMX_PWM_BASE (0x08000 + IMX_IO_BASE) -#define IMX_DMAC_BASE (0x09000 + IMX_IO_BASE) -#define IMX_AIPI2_BASE (0x10000 + IMX_IO_BASE) -#define IMX_SIM_BASE (0x11000 + IMX_IO_BASE) -#define IMX_USBD_BASE (0x12000 + IMX_IO_BASE) -#define IMX_SPI1_BASE (0x13000 + IMX_IO_BASE) -#define IMX_MMC_BASE (0x14000 + IMX_IO_BASE) -#define IMX_ASP_BASE (0x15000 + IMX_IO_BASE) -#define IMX_BTA_BASE (0x16000 + IMX_IO_BASE) -#define IMX_I2C_BASE (0x17000 + IMX_IO_BASE) -#define IMX_SSI_BASE (0x18000 + IMX_IO_BASE) -#define IMX_SPI2_BASE (0x19000 + IMX_IO_BASE) -#define IMX_MSHC_BASE (0x1A000 + IMX_IO_BASE) -#define IMX_PLL_BASE (0x1B000 + IMX_IO_BASE) -#define IMX_GPIO_BASE (0x1C000 + IMX_IO_BASE) -#define IMX_EIM_BASE (0x20000 + IMX_IO_BASE) -#define IMX_SDRAMC_BASE (0x21000 + IMX_IO_BASE) -#define IMX_MMA_BASE (0x22000 + IMX_IO_BASE) -#define IMX_AITC_BASE (0x23000 + IMX_IO_BASE) -#define IMX_CSI_BASE (0x24000 + IMX_IO_BASE) - -/* PLL registers */ -#define CSCR __REG(IMX_PLL_BASE) /* Clock Source Control Register */ -#define CSCR_SPLL_RESTART (1<<22) -#define CSCR_MPLL_RESTART (1<<21) -#define CSCR_SYSTEM_SEL (1<<16) -#define CSCR_BCLK_DIV (0xf<<10) -#define CSCR_MPU_PRESC (1<<15) -#define CSCR_SPEN (1<<1) -#define CSCR_MPEN (1<<0) - -#define MPCTL0 __REG(IMX_PLL_BASE + 0x4) /* MCU PLL Control Register 0 */ -#define MPCTL1 __REG(IMX_PLL_BASE + 0x8) /* MCU PLL and System Clock Register 1 */ -#define SPCTL0 __REG(IMX_PLL_BASE + 0xc) /* System PLL Control Register 0 */ -#define SPCTL1 __REG(IMX_PLL_BASE + 0x10) /* System PLL Control Register 1 */ -#define PCDR __REG(IMX_PLL_BASE + 0x20) /* Peripheral Clock Divider Register */ - -/* - * GPIO Module and I/O Multiplexer - * x = 0..3 for reg_A, reg_B, reg_C, reg_D - */ -#define DDIR(x) __REG2(IMX_GPIO_BASE + 0x00, ((x) & 3) << 8) -#define OCR1(x) __REG2(IMX_GPIO_BASE + 0x04, ((x) & 3) << 8) -#define OCR2(x) __REG2(IMX_GPIO_BASE + 0x08, ((x) & 3) << 8) -#define ICONFA1(x) __REG2(IMX_GPIO_BASE + 0x0c, ((x) & 3) << 8) -#define ICONFA2(x) __REG2(IMX_GPIO_BASE + 0x10, ((x) & 3) << 8) -#define ICONFB1(x) __REG2(IMX_GPIO_BASE + 0x14, ((x) & 3) << 8) -#define ICONFB2(x) __REG2(IMX_GPIO_BASE + 0x18, ((x) & 3) << 8) -#define DR(x) __REG2(IMX_GPIO_BASE + 0x1c, ((x) & 3) << 8) -#define GIUS(x) __REG2(IMX_GPIO_BASE + 0x20, ((x) & 3) << 8) -#define SSR(x) __REG2(IMX_GPIO_BASE + 0x24, ((x) & 3) << 8) -#define ICR1(x) __REG2(IMX_GPIO_BASE + 0x28, ((x) & 3) << 8) -#define ICR2(x) __REG2(IMX_GPIO_BASE + 0x2c, ((x) & 3) << 8) -#define IMR(x) __REG2(IMX_GPIO_BASE + 0x30, ((x) & 3) << 8) -#define ISR(x) __REG2(IMX_GPIO_BASE + 0x34, ((x) & 3) << 8) -#define GPR(x) __REG2(IMX_GPIO_BASE + 0x38, ((x) & 3) << 8) -#define SWR(x) __REG2(IMX_GPIO_BASE + 0x3c, ((x) & 3) << 8) -#define PUEN(x) __REG2(IMX_GPIO_BASE + 0x40, ((x) & 3) << 8) - -#define GPIO_PORT_MAX 3 - -#define GPIO_PIN_MASK 0x1f -#define GPIO_PORT_MASK (0x3 << 5) - -#define GPIO_PORT_SHIFT 5 -#define GPIO_PORTA (0<<5) -#define GPIO_PORTB (1<<5) -#define GPIO_PORTC (2<<5) -#define GPIO_PORTD (3<<5) - -#define GPIO_OUT (1<<7) -#define GPIO_IN (0<<7) -#define GPIO_PUEN (1<<8) - -#define GPIO_PF (0<<9) -#define GPIO_AF (1<<9) - -#define GPIO_OCR_SHIFT 10 -#define GPIO_OCR_MASK (3<<10) -#define GPIO_AIN (0<<10) -#define GPIO_BIN (1<<10) -#define GPIO_CIN (2<<10) -#define GPIO_DR (3<<10) - -#define GPIO_AOUT_SHIFT 12 -#define GPIO_AOUT_MASK (3<<12) -#define GPIO_AOUT (0<<12) -#define GPIO_AOUT_ISR (1<<12) -#define GPIO_AOUT_0 (2<<12) -#define GPIO_AOUT_1 (3<<12) - -#define GPIO_BOUT_SHIFT 14 -#define GPIO_BOUT_MASK (3<<14) -#define GPIO_BOUT (0<<14) -#define GPIO_BOUT_ISR (1<<14) -#define GPIO_BOUT_0 (2<<14) -#define GPIO_BOUT_1 (3<<14) - -#define GPIO_GIUS (1<<16) - -/* assignements for GPIO alternate/primary functions */ - -/* FIXME: This list is not completed. The correct directions are - * missing on some (many) pins - */ -#define PA0_AIN_SPI2_CLK ( GPIO_GIUS | GPIO_PORTA | GPIO_OUT | 0 ) -#define PA0_AF_ETMTRACESYNC ( GPIO_PORTA | GPIO_AF | 0 ) -#define PA1_AOUT_SPI2_RXD ( GPIO_GIUS | GPIO_PORTA | GPIO_IN | 1 ) -#define PA1_PF_TIN ( GPIO_PORTA | GPIO_PF | 1 ) -#define PA2_PF_PWM0 ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 2 ) -#define PA3_PF_CSI_MCLK ( GPIO_PORTA | GPIO_PF | 3 ) -#define PA4_PF_CSI_D0 ( GPIO_PORTA | GPIO_PF | 4 ) -#define PA5_PF_CSI_D1 ( GPIO_PORTA | GPIO_PF | 5 ) -#define PA6_PF_CSI_D2 ( GPIO_PORTA | GPIO_PF | 6 ) -#define PA7_PF_CSI_D3 ( GPIO_PORTA | GPIO_PF | 7 ) -#define PA8_PF_CSI_D4 ( GPIO_PORTA | GPIO_PF | 8 ) -#define PA9_PF_CSI_D5 ( GPIO_PORTA | GPIO_PF | 9 ) -#define PA10_PF_CSI_D6 ( GPIO_PORTA | GPIO_PF | 10 ) -#define PA11_PF_CSI_D7 ( GPIO_PORTA | GPIO_PF | 11 ) -#define PA12_PF_CSI_VSYNC ( GPIO_PORTA | GPIO_PF | 12 ) -#define PA13_PF_CSI_HSYNC ( GPIO_PORTA | GPIO_PF | 13 ) -#define PA14_PF_CSI_PIXCLK ( GPIO_PORTA | GPIO_PF | 14 ) -#define PA15_PF_I2C_SDA ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 15 ) -#define PA16_PF_I2C_SCL ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 16 ) -#define PA17_AF_ETMTRACEPKT4 ( GPIO_PORTA | GPIO_AF | 17 ) -#define PA17_AIN_SPI2_SS ( GPIO_GIUS | GPIO_PORTA | GPIO_OUT | 17 ) -#define PA18_AF_ETMTRACEPKT5 ( GPIO_PORTA | GPIO_AF | 18 ) -#define PA19_AF_ETMTRACEPKT6 ( GPIO_PORTA | GPIO_AF | 19 ) -#define PA20_AF_ETMTRACEPKT7 ( GPIO_PORTA | GPIO_AF | 20 ) -#define PA21_PF_A0 ( GPIO_PORTA | GPIO_PF | 21 ) -#define PA22_PF_CS4 ( GPIO_PORTA | GPIO_PF | 22 ) -#define PA23_PF_CS5 ( GPIO_PORTA | GPIO_PF | 23 ) -#define PA24_PF_A16 ( GPIO_PORTA | GPIO_PF | 24 ) -#define PA24_AF_ETMTRACEPKT0 ( GPIO_PORTA | GPIO_AF | 24 ) -#define PA25_PF_A17 ( GPIO_PORTA | GPIO_PF | 25 ) -#define PA25_AF_ETMTRACEPKT1 ( GPIO_PORTA | GPIO_AF | 25 ) -#define PA26_PF_A18 ( GPIO_PORTA | GPIO_PF | 26 ) -#define PA26_AF_ETMTRACEPKT2 ( GPIO_PORTA | GPIO_AF | 26 ) -#define PA27_PF_A19 ( GPIO_PORTA | GPIO_PF | 27 ) -#define PA27_AF_ETMTRACEPKT3 ( GPIO_PORTA | GPIO_AF | 27 ) -#define PA28_PF_A20 ( GPIO_PORTA | GPIO_PF | 28 ) -#define PA28_AF_ETMPIPESTAT0 ( GPIO_PORTA | GPIO_AF | 28 ) -#define PA29_PF_A21 ( GPIO_PORTA | GPIO_PF | 29 ) -#define PA29_AF_ETMPIPESTAT1 ( GPIO_PORTA | GPIO_AF | 29 ) -#define PA30_PF_A22 ( GPIO_PORTA | GPIO_PF | 30 ) -#define PA30_AF_ETMPIPESTAT2 ( GPIO_PORTA | GPIO_AF | 30 ) -#define PA31_PF_A23 ( GPIO_PORTA | GPIO_PF | 31 ) -#define PA31_AF_ETMTRACECLK ( GPIO_PORTA | GPIO_AF | 31 ) -#define PB8_PF_SD_DAT0 ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 8 ) -#define PB8_AF_MS_PIO ( GPIO_PORTB | GPIO_AF | 8 ) -#define PB9_PF_SD_DAT1 ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 9 ) -#define PB9_AF_MS_PI1 ( GPIO_PORTB | GPIO_AF | 9 ) -#define PB10_PF_SD_DAT2 ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 10 ) -#define PB10_AF_MS_SCLKI ( GPIO_PORTB | GPIO_AF | 10 ) -#define PB11_PF_SD_DAT3 ( GPIO_PORTB | GPIO_PF | 11 ) -#define PB11_AF_MS_SDIO ( GPIO_PORTB | GPIO_AF | 11 ) -#define PB12_PF_SD_CLK ( GPIO_PORTB | GPIO_PF | 12 ) -#define PB12_AF_MS_SCLK0 ( GPIO_PORTB | GPIO_AF | 12 ) -#define PB13_PF_SD_CMD ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 13 ) -#define PB13_AF_MS_BS ( GPIO_PORTB | GPIO_AF | 13 ) -#define PB14_AF_SSI_RXFS ( GPIO_PORTB | GPIO_AF | 14 ) -#define PB15_AF_SSI_RXCLK ( GPIO_PORTB | GPIO_AF | 15 ) -#define PB16_AF_SSI_RXDAT ( GPIO_PORTB | GPIO_IN | GPIO_AF | 16 ) -#define PB17_AF_SSI_TXDAT ( GPIO_PORTB | GPIO_OUT | GPIO_AF | 17 ) -#define PB18_AF_SSI_TXFS ( GPIO_PORTB | GPIO_AF | 18 ) -#define PB19_AF_SSI_TXCLK ( GPIO_PORTB | GPIO_AF | 19 ) -#define PB20_PF_USBD_AFE ( GPIO_PORTB | GPIO_PF | 20 ) -#define PB21_PF_USBD_OE ( GPIO_PORTB | GPIO_PF | 21 ) -#define PB22_PFUSBD_RCV ( GPIO_PORTB | GPIO_PF | 22 ) -#define PB23_PF_USBD_SUSPND ( GPIO_PORTB | GPIO_PF | 23 ) -#define PB24_PF_USBD_VP ( GPIO_PORTB | GPIO_PF | 24 ) -#define PB25_PF_USBD_VM ( GPIO_PORTB | GPIO_PF | 25 ) -#define PB26_PF_USBD_VPO ( GPIO_PORTB | GPIO_PF | 26 ) -#define PB27_PF_USBD_VMO ( GPIO_PORTB | GPIO_PF | 27 ) -#define PB28_PF_UART2_CTS ( GPIO_PORTB | GPIO_OUT | GPIO_PF | 28 ) -#define PB29_PF_UART2_RTS ( GPIO_PORTB | GPIO_IN | GPIO_PF | 29 ) -#define PB30_PF_UART2_TXD ( GPIO_PORTB | GPIO_OUT | GPIO_PF | 30 ) -#define PB31_PF_UART2_RXD ( GPIO_PORTB | GPIO_IN | GPIO_PF | 31 ) -#define PC3_PF_SSI_RXFS ( GPIO_PORTC | GPIO_PF | 3 ) -#define PC4_PF_SSI_RXCLK ( GPIO_PORTC | GPIO_PF | 4 ) -#define PC5_PF_SSI_RXDAT ( GPIO_PORTC | GPIO_IN | GPIO_PF | 5 ) -#define PC6_PF_SSI_TXDAT ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 6 ) -#define PC7_PF_SSI_TXFS ( GPIO_PORTC | GPIO_PF | 7 ) -#define PC8_PF_SSI_TXCLK ( GPIO_PORTC | GPIO_PF | 8 ) -#define PC9_PF_UART1_CTS ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 9 ) -#define PC10_PF_UART1_RTS ( GPIO_PORTC | GPIO_IN | GPIO_PF | 10 ) -#define PC11_PF_UART1_TXD ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 11 ) -#define PC12_PF_UART1_RXD ( GPIO_PORTC | GPIO_IN | GPIO_PF | 12 ) -#define PC13_PF_SPI1_SPI_RDY ( GPIO_PORTC | GPIO_PF | 13 ) -#define PC14_PF_SPI1_SCLK ( GPIO_PORTC | GPIO_PF | 14 ) -#define PC15_PF_SPI1_SS ( GPIO_PORTC | GPIO_PF | 15 ) -#define PC16_PF_SPI1_MISO ( GPIO_PORTC | GPIO_PF | 16 ) -#define PC17_PF_SPI1_MOSI ( GPIO_PORTC | GPIO_PF | 17 ) -#define PC24_BIN_UART3_RI ( GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 24 ) -#define PC25_BIN_UART3_DSR ( GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 25 ) -#define PC26_AOUT_UART3_DTR ( GPIO_GIUS | GPIO_PORTC | GPIO_IN | 26 ) -#define PC27_BIN_UART3_DCD ( GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 27 ) -#define PC28_BIN_UART3_CTS ( GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 28 ) -#define PC29_AOUT_UART3_RTS ( GPIO_GIUS | GPIO_PORTC | GPIO_IN | 29 ) -#define PC30_BIN_UART3_TX ( GPIO_GIUS | GPIO_PORTC | GPIO_BIN | 30 ) -#define PC31_AOUT_UART3_RX ( GPIO_GIUS | GPIO_PORTC | GPIO_IN | 31) -#define PD6_PF_LSCLK ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 6 ) -#define PD7_PF_REV ( GPIO_PORTD | GPIO_PF | 7 ) -#define PD7_AF_UART2_DTR ( GPIO_GIUS | GPIO_PORTD | GPIO_IN | GPIO_AF | 7 ) -#define PD7_AIN_SPI2_SCLK ( GPIO_GIUS | GPIO_PORTD | GPIO_AIN | 7 ) -#define PD8_PF_CLS ( GPIO_PORTD | GPIO_PF | 8 ) -#define PD8_AF_UART2_DCD ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 8 ) -#define PD8_AIN_SPI2_SS ( GPIO_GIUS | GPIO_PORTD | GPIO_AIN | 8 ) -#define PD9_PF_PS ( GPIO_PORTD | GPIO_PF | 9 ) -#define PD9_AF_UART2_RI ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 9 ) -#define PD9_AOUT_SPI2_RXD ( GPIO_GIUS | GPIO_PORTD | GPIO_IN | 9 ) -#define PD10_PF_SPL_SPR ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 10 ) -#define PD10_AF_UART2_DSR ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 10 ) -#define PD10_AIN_SPI2_TXD ( GPIO_GIUS | GPIO_PORTD | GPIO_OUT | 10 ) -#define PD11_PF_CONTRAST ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 11 ) -#define PD12_PF_ACD_OE ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 12 ) -#define PD13_PF_LP_HSYNC ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 13 ) -#define PD14_PF_FLM_VSYNC ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 14 ) -#define PD15_PF_LD0 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 15 ) -#define PD16_PF_LD1 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 16 ) -#define PD17_PF_LD2 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 17 ) -#define PD18_PF_LD3 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 18 ) -#define PD19_PF_LD4 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 19 ) -#define PD20_PF_LD5 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 20 ) -#define PD21_PF_LD6 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 21 ) -#define PD22_PF_LD7 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 22 ) -#define PD23_PF_LD8 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 23 ) -#define PD24_PF_LD9 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 24 ) -#define PD25_PF_LD10 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 25 ) -#define PD26_PF_LD11 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 26 ) -#define PD27_PF_LD12 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 27 ) -#define PD28_PF_LD13 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 28 ) -#define PD29_PF_LD14 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 29 ) -#define PD30_PF_LD15 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 30 ) -#define PD31_PF_TMR2OUT ( GPIO_PORTD | GPIO_PF | 31 ) -#define PD31_BIN_SPI2_TXD ( GPIO_GIUS | GPIO_PORTD | GPIO_BIN | 31 ) - -/* - * PWM controller - */ -#define PWMC __REG(IMX_PWM_BASE + 0x00) /* PWM Control Register */ -#define PWMS __REG(IMX_PWM_BASE + 0x04) /* PWM Sample Register */ -#define PWMP __REG(IMX_PWM_BASE + 0x08) /* PWM Period Register */ -#define PWMCNT __REG(IMX_PWM_BASE + 0x0C) /* PWM Counter Register */ - -#define PWMC_HCTR (0x01<<18) /* Halfword FIFO Data Swapping */ -#define PWMC_BCTR (0x01<<17) /* Byte FIFO Data Swapping */ -#define PWMC_SWR (0x01<<16) /* Software Reset */ -#define PWMC_CLKSRC (0x01<<15) /* Clock Source */ -#define PWMC_PRESCALER(x) (((x-1) & 0x7F) << 8) /* PRESCALER */ -#define PWMC_IRQ (0x01<< 7) /* Interrupt Request */ -#define PWMC_IRQEN (0x01<< 6) /* Interrupt Request Enable */ -#define PWMC_FIFOAV (0x01<< 5) /* FIFO Available */ -#define PWMC_EN (0x01<< 4) /* Enables/Disables the PWM */ -#define PWMC_REPEAT(x) (((x) & 0x03) << 2) /* Sample Repeats */ -#define PWMC_CLKSEL(x) (((x) & 0x03) << 0) /* Clock Selection */ - -#define PWMS_SAMPLE(x) ((x) & 0xFFFF) /* Contains a two-sample word */ -#define PWMP_PERIOD(x) ((x) & 0xFFFF) /* Represents the PWM's period */ -#define PWMC_COUNTER(x) ((x) & 0xFFFF) /* Represents the current count value */ - -/* - * DMA Controller - */ -#define DCR __REG(IMX_DMAC_BASE +0x00) /* DMA Control Register */ -#define DISR __REG(IMX_DMAC_BASE +0x04) /* DMA Interrupt status Register */ -#define DIMR __REG(IMX_DMAC_BASE +0x08) /* DMA Interrupt mask Register */ -#define DBTOSR __REG(IMX_DMAC_BASE +0x0c) /* DMA Burst timeout status Register */ -#define DRTOSR __REG(IMX_DMAC_BASE +0x10) /* DMA Request timeout Register */ -#define DSESR __REG(IMX_DMAC_BASE +0x14) /* DMA Transfer Error Status Register */ -#define DBOSR __REG(IMX_DMAC_BASE +0x18) /* DMA Buffer overflow status Register */ -#define DBTOCR __REG(IMX_DMAC_BASE +0x1c) /* DMA Burst timeout control Register */ -#define WSRA __REG(IMX_DMAC_BASE +0x40) /* W-Size Register A */ -#define XSRA __REG(IMX_DMAC_BASE +0x44) /* X-Size Register A */ -#define YSRA __REG(IMX_DMAC_BASE +0x48) /* Y-Size Register A */ -#define WSRB __REG(IMX_DMAC_BASE +0x4c) /* W-Size Register B */ -#define XSRB __REG(IMX_DMAC_BASE +0x50) /* X-Size Register B */ -#define YSRB __REG(IMX_DMAC_BASE +0x54) /* Y-Size Register B */ -#define SAR(x) __REG2( IMX_DMAC_BASE + 0x80, (x) << 6) /* Source Address Registers */ -#define DAR(x) __REG2( IMX_DMAC_BASE + 0x84, (x) << 6) /* Destination Address Registers */ -#define CNTR(x) __REG2( IMX_DMAC_BASE + 0x88, (x) << 6) /* Count Registers */ -#define CCR(x) __REG2( IMX_DMAC_BASE + 0x8c, (x) << 6) /* Control Registers */ -#define RSSR(x) __REG2( IMX_DMAC_BASE + 0x90, (x) << 6) /* Request source select Registers */ -#define BLR(x) __REG2( IMX_DMAC_BASE + 0x94, (x) << 6) /* Burst length Registers */ -#define RTOR(x) __REG2( IMX_DMAC_BASE + 0x98, (x) << 6) /* Request timeout Registers */ -#define BUCR(x) __REG2( IMX_DMAC_BASE + 0x98, (x) << 6) /* Bus Utilization Registers */ - -#define DCR_DRST (1<<1) -#define DCR_DEN (1<<0) -#define DBTOCR_EN (1<<15) -#define DBTOCR_CNT(x) ((x) & 0x7fff ) -#define CNTR_CNT(x) ((x) & 0xffffff ) -#define CCR_DMOD_LINEAR ( 0x0 << 12 ) -#define CCR_DMOD_2D ( 0x1 << 12 ) -#define CCR_DMOD_FIFO ( 0x2 << 12 ) -#define CCR_DMOD_EOBFIFO ( 0x3 << 12 ) -#define CCR_SMOD_LINEAR ( 0x0 << 10 ) -#define CCR_SMOD_2D ( 0x1 << 10 ) -#define CCR_SMOD_FIFO ( 0x2 << 10 ) -#define CCR_SMOD_EOBFIFO ( 0x3 << 10 ) -#define CCR_MDIR_DEC (1<<9) -#define CCR_MSEL_B (1<<8) -#define CCR_DSIZ_32 ( 0x0 << 6 ) -#define CCR_DSIZ_8 ( 0x1 << 6 ) -#define CCR_DSIZ_16 ( 0x2 << 6 ) -#define CCR_SSIZ_32 ( 0x0 << 4 ) -#define CCR_SSIZ_8 ( 0x1 << 4 ) -#define CCR_SSIZ_16 ( 0x2 << 4 ) -#define CCR_REN (1<<3) -#define CCR_RPT (1<<2) -#define CCR_FRC (1<<1) -#define CCR_CEN (1<<0) -#define RTOR_EN (1<<15) -#define RTOR_CLK (1<<14) -#define RTOR_PSC (1<<13) - -/* - * Interrupt controller - */ - -#define IMX_INTCNTL __REG(IMX_AITC_BASE+0x00) -#define INTCNTL_FIAD (1<<19) -#define INTCNTL_NIAD (1<<20) - -#define IMX_NIMASK __REG(IMX_AITC_BASE+0x04) -#define IMX_INTENNUM __REG(IMX_AITC_BASE+0x08) -#define IMX_INTDISNUM __REG(IMX_AITC_BASE+0x0c) -#define IMX_INTENABLEH __REG(IMX_AITC_BASE+0x10) -#define IMX_INTENABLEL __REG(IMX_AITC_BASE+0x14) - -/* - * General purpose timers - */ -#define IMX_TCTL(x) __REG( 0x00 + (x)) -#define TCTL_SWR (1<<15) -#define TCTL_FRR (1<<8) -#define TCTL_CAP_RIS (1<<6) -#define TCTL_CAP_FAL (2<<6) -#define TCTL_CAP_RIS_FAL (3<<6) -#define TCTL_OM (1<<5) -#define TCTL_IRQEN (1<<4) -#define TCTL_CLK_PCLK1 (1<<1) -#define TCTL_CLK_PCLK1_16 (2<<1) -#define TCTL_CLK_TIN (3<<1) -#define TCTL_CLK_32 (4<<1) -#define TCTL_TEN (1<<0) - -#define IMX_TPRER(x) __REG( 0x04 + (x)) -#define IMX_TCMP(x) __REG( 0x08 + (x)) -#define IMX_TCR(x) __REG( 0x0C + (x)) -#define IMX_TCN(x) __REG( 0x10 + (x)) -#define IMX_TSTAT(x) __REG( 0x14 + (x)) -#define TSTAT_CAPT (1<<1) -#define TSTAT_COMP (1<<0) - -#endif // _IMX_REGS_H diff --git a/arch/arm/mach-imx/include/mach/imx-uart.h b/arch/arm/mach-imx/include/mach/imx-uart.h deleted file mode 100644 index d54eb1d4802..00000000000 --- a/arch/arm/mach-imx/include/mach/imx-uart.h +++ /dev/null @@ -1,12 +0,0 @@ -#ifndef ASMARM_ARCH_UART_H -#define ASMARM_ARCH_UART_H - -#define IMXUART_HAVE_RTSCTS (1<<0) - -struct imxuart_platform_data { - int (*init)(struct platform_device *pdev); - void (*exit)(struct platform_device *pdev); - unsigned int flags; -}; - -#endif diff --git a/arch/arm/mach-imx/include/mach/io.h b/arch/arm/mach-imx/include/mach/io.h deleted file mode 100644 index 9e197ae4590..00000000000 --- a/arch/arm/mach-imx/include/mach/io.h +++ /dev/null @@ -1,28 +0,0 @@ -/* - * arch/arm/mach-imxads/include/mach/io.h - * - * Copyright (C) 1999 ARM Limited - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#ifndef __ASM_ARM_ARCH_IO_H -#define __ASM_ARM_ARCH_IO_H - -#define IO_SPACE_LIMIT 0xffffffff - -#define __io(a) __typesafe_io(a) -#define __mem_pci(a) (a) - -#endif diff --git a/arch/arm/mach-imx/include/mach/irqs.h b/arch/arm/mach-imx/include/mach/irqs.h deleted file mode 100644 index 67812c5ac1f..00000000000 --- a/arch/arm/mach-imx/include/mach/irqs.h +++ /dev/null @@ -1,121 +0,0 @@ -/* - * arch/arm/mach-imxads/include/mach/irqs.h - * - * Copyright (C) 1999 ARM Limited - * Copyright (C) 2000 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ARM_IRQS_H__ -#define __ARM_IRQS_H__ - -/* Use the imx definitions */ -#include <mach/hardware.h> - -/* - * IMX Interrupt numbers - * - */ -#define INT_SOFTINT 0 -#define CSI_INT 6 -#define DSPA_MAC_INT 7 -#define DSPA_INT 8 -#define COMP_INT 9 -#define MSHC_XINT 10 -#define GPIO_INT_PORTA 11 -#define GPIO_INT_PORTB 12 -#define GPIO_INT_PORTC 13 -#define LCDC_INT 14 -#define SIM_INT 15 -#define SIM_DATA_INT 16 -#define RTC_INT 17 -#define RTC_SAMINT 18 -#define UART2_MINT_PFERR 19 -#define UART2_MINT_RTS 20 -#define UART2_MINT_DTR 21 -#define UART2_MINT_UARTC 22 -#define UART2_MINT_TX 23 -#define UART2_MINT_RX 24 -#define UART1_MINT_PFERR 25 -#define UART1_MINT_RTS 26 -#define UART1_MINT_DTR 27 -#define UART1_MINT_UARTC 28 -#define UART1_MINT_TX 29 -#define UART1_MINT_RX 30 -#define VOICE_DAC_INT 31 -#define VOICE_ADC_INT 32 -#define PEN_DATA_INT 33 -#define PWM_INT 34 -#define SDHC_INT 35 -#define I2C_INT 39 -#define CSPI_INT 41 -#define SSI_TX_INT 42 -#define SSI_TX_ERR_INT 43 -#define SSI_RX_INT 44 -#define SSI_RX_ERR_INT 45 -#define TOUCH_INT 46 -#define USBD_INT0 47 -#define USBD_INT1 48 -#define USBD_INT2 49 -#define USBD_INT3 50 -#define USBD_INT4 51 -#define USBD_INT5 52 -#define USBD_INT6 53 -#define BTSYS_INT 55 -#define BTTIM_INT 56 -#define BTWUI_INT 57 -#define TIM2_INT 58 -#define TIM1_INT 59 -#define DMA_ERR 60 -#define DMA_INT 61 -#define GPIO_INT_PORTD 62 - -#define IMX_IRQS (64) - -/* note: the IMX has four gpio ports (A-D), but only - * the following pins are connected to the outside - * world: - * - * PORT A: bits 0-31 - * PORT B: bits 8-31 - * PORT C: bits 3-17 - * PORT D: bits 6-31 - * - * We map these interrupts straight on. As a result we have - * several holes in the interrupt mapping. We do this for two - * reasons: - * - mapping the interrupts without holes would get - * far more complicated - * - Motorola could well decide to bring some processor - * with more pins connected - */ - -#define IRQ_GPIOA(x) (IMX_IRQS + x) -#define IRQ_GPIOB(x) (IRQ_GPIOA(32) + x) -#define IRQ_GPIOC(x) (IRQ_GPIOB(32) + x) -#define IRQ_GPIOD(x) (IRQ_GPIOC(32) + x) - -/* decode irq number to use with IMR(x), ISR(x) and friends */ -#define IRQ_TO_REG(irq) ((irq - IMX_IRQS) >> 5) - -/* all normal IRQs can be FIQs */ -#define FIQ_START 0 -/* switch betwean IRQ and FIQ */ -extern int imx_set_irq_fiq(unsigned int irq, unsigned int type); - -#define NR_IRQS (IRQ_GPIOD(32) + 1) -#define IRQ_GPIO(x) -#endif diff --git a/arch/arm/mach-imx/include/mach/memory.h b/arch/arm/mach-imx/include/mach/memory.h deleted file mode 100644 index a93df7cba69..00000000000 --- a/arch/arm/mach-imx/include/mach/memory.h +++ /dev/null @@ -1,26 +0,0 @@ -/* - * arch/arm/mach-imx/include/mach/memory.h - * - * Copyright (C) 1999 ARM Limited - * Copyright (C) 2002 Shane Nay (shane@minirl.com) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#ifndef __ASM_ARCH_MMU_H -#define __ASM_ARCH_MMU_H - -#define PHYS_OFFSET UL(0x08000000) - -#endif diff --git a/arch/arm/mach-imx/include/mach/mmc.h b/arch/arm/mach-imx/include/mach/mmc.h deleted file mode 100644 index 4712f354dcc..00000000000 --- a/arch/arm/mach-imx/include/mach/mmc.h +++ /dev/null @@ -1,15 +0,0 @@ -#ifndef ASMARM_ARCH_MMC_H -#define ASMARM_ARCH_MMC_H - -#include <linux/mmc/host.h> - -struct device; - -struct imxmmc_platform_data { - int (*card_present)(struct device *); - int (*get_ro)(struct device *); -}; - -extern void imx_set_mmc_info(struct imxmmc_platform_data *info); - -#endif diff --git a/arch/arm/mach-imx/include/mach/spi_imx.h b/arch/arm/mach-imx/include/mach/spi_imx.h deleted file mode 100644 index 4186430feec..00000000000 --- a/arch/arm/mach-imx/include/mach/spi_imx.h +++ /dev/null @@ -1,72 +0,0 @@ -/* - * arch/arm/mach-imx/include/mach/spi_imx.h - * - * Copyright (C) 2006 SWAPP - * Andrea Paterniani <a.paterniani@swapp-eng.it> - * - * Initial version inspired by: - * linux-2.6.17-rc3-mm1/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#ifndef SPI_IMX_H_ -#define SPI_IMX_H_ - - -/*-------------------------------------------------------------------------*/ -/** - * struct spi_imx_master - device.platform_data for SPI controller devices. - * @num_chipselect: chipselects are used to distinguish individual - * SPI slaves, and are numbered from zero to num_chipselects - 1. - * each slave has a chipselect signal, but it's common that not - * every chipselect is connected to a slave. - * @enable_dma: if true enables DMA driven transfers. -*/ -struct spi_imx_master { - u8 num_chipselect; - u8 enable_dma:1; -}; -/*-------------------------------------------------------------------------*/ - - -/*-------------------------------------------------------------------------*/ -/** - * struct spi_imx_chip - spi_board_info.controller_data for SPI - * slave devices, copied to spi_device.controller_data. - * @enable_loopback : used for test purpouse to internally connect RX and TX - * sections. - * @enable_dma : enables dma transfer (provided that controller driver has - * dma enabled too). - * @ins_ss_pulse : enable /SS pulse insertion between SPI burst. - * @bclk_wait : number of bclk waits between each bits_per_word SPI burst. - * @cs_control : function pointer to board-specific function to assert/deassert - * I/O port to control HW generation of devices chip-select. -*/ -struct spi_imx_chip { - u8 enable_loopback:1; - u8 enable_dma:1; - u8 ins_ss_pulse:1; - u16 bclk_wait:15; - void (*cs_control)(u32 control); -}; - -/* Chip-select state */ -#define SPI_CS_ASSERT (1 << 0) -#define SPI_CS_DEASSERT (1 << 1) -/*-------------------------------------------------------------------------*/ - - -#endif /* SPI_IMX_H_*/ diff --git a/arch/arm/mach-imx/include/mach/system.h b/arch/arm/mach-imx/include/mach/system.h deleted file mode 100644 index 46d4ca91af7..00000000000 --- a/arch/arm/mach-imx/include/mach/system.h +++ /dev/null @@ -1,40 +0,0 @@ -/* - * arch/arm/mach-imxads/include/mach/system.h - * - * Copyright (C) 1999 ARM Limited - * Copyright (C) 2000 Deep Blue Solutions Ltd - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#ifndef __ASM_ARCH_SYSTEM_H -#define __ASM_ARCH_SYSTEM_H - -static void -arch_idle(void) -{ - /* - * This should do all the clock switching - * and wait for interrupt tricks - */ - cpu_do_idle(); -} - -static inline void -arch_reset(char mode, const char *cmd) -{ - cpu_reset(0); -} - -#endif diff --git a/arch/arm/mach-imx/include/mach/uncompress.h b/arch/arm/mach-imx/include/mach/uncompress.h deleted file mode 100644 index 70523e67a8f..00000000000 --- a/arch/arm/mach-imx/include/mach/uncompress.h +++ /dev/null @@ -1,71 +0,0 @@ -/* - * arch/arm/mach-imxads/include/mach/uncompress.h - * - * - * - * Copyright (C) 1999 ARM Limited - * Copyright (C) Shane Nay (shane@minirl.com) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#define UART(x) (*(volatile unsigned long *)(serial_port + (x))) - -#define UART1_BASE 0x206000 -#define UART2_BASE 0x207000 -#define USR2 0x98 -#define USR2_TXFE (1<<14) -#define TXR 0x40 -#define UCR1 0x80 -#define UCR1_UARTEN 1 - -/* - * The following code assumes the serial port has already been - * initialized by the bootloader. We search for the first enabled - * port in the most probable order. If you didn't setup a port in - * your bootloader then nothing will appear (which might be desired). - * - * This does not append a newline - */ -static void putc(int c) -{ - unsigned long serial_port; - - do { - serial_port = UART1_BASE; - if ( UART(UCR1) & UCR1_UARTEN ) - break; - serial_port = UART2_BASE; - if ( UART(UCR1) & UCR1_UARTEN ) - break; - return; - } while(0); - - while (!(UART(USR2) & USR2_TXFE)) - barrier(); - - UART(TXR) = c; -} - -static inline void flush(void) -{ -} - -/* - * nothing to do - */ -#define arch_decomp_setup() - -#define arch_decomp_wdog() diff --git a/arch/arm/mach-imx/include/mach/vmalloc.h b/arch/arm/mach-imx/include/mach/vmalloc.h deleted file mode 100644 index 7d7cb0bde3e..00000000000 --- a/arch/arm/mach-imx/include/mach/vmalloc.h +++ /dev/null @@ -1,20 +0,0 @@ -/* - * arch/arm/mach-imx/include/mach/vmalloc.h - * - * Copyright (C) 2000 Russell King. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#define VMALLOC_END (PAGE_OFFSET + 0x10000000) diff --git a/arch/arm/mach-imx/irq.c b/arch/arm/mach-imx/irq.c deleted file mode 100644 index 531b95deadc..00000000000 --- a/arch/arm/mach-imx/irq.c +++ /dev/null @@ -1,311 +0,0 @@ -/* - * linux/arch/arm/mach-imx/irq.c - * - * Copyright (C) 1999 ARM Limited - * Copyright (C) 2002 Shane Nay (shane@minirl.com) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - * 03/03/2004 Sascha Hauer <sascha@saschahauer.de> - * Copied from the motorola bsp package and added gpio demux - * interrupt handler - */ - -#include <linux/init.h> -#include <linux/list.h> -#include <linux/timer.h> -#include <linux/io.h> - -#include <mach/hardware.h> -#include <asm/irq.h> - -#include <asm/mach/irq.h> - -/* - * - * We simply use the ENABLE DISABLE registers inside of the IMX - * to turn on/off specific interrupts. - * - */ - -#define INTCNTL_OFF 0x00 -#define NIMASK_OFF 0x04 -#define INTENNUM_OFF 0x08 -#define INTDISNUM_OFF 0x0C -#define INTENABLEH_OFF 0x10 -#define INTENABLEL_OFF 0x14 -#define INTTYPEH_OFF 0x18 -#define INTTYPEL_OFF 0x1C -#define NIPRIORITY_OFF(x) (0x20+4*(7-(x))) -#define NIVECSR_OFF 0x40 -#define FIVECSR_OFF 0x44 -#define INTSRCH_OFF 0x48 -#define INTSRCL_OFF 0x4C -#define INTFRCH_OFF 0x50 -#define INTFRCL_OFF 0x54 -#define NIPNDH_OFF 0x58 -#define NIPNDL_OFF 0x5C -#define FIPNDH_OFF 0x60 -#define FIPNDL_OFF 0x64 - -#define VA_AITC_BASE IO_ADDRESS(IMX_AITC_BASE) -#define IMX_AITC_INTCNTL (VA_AITC_BASE + INTCNTL_OFF) -#define IMX_AITC_NIMASK (VA_AITC_BASE + NIMASK_OFF) -#define IMX_AITC_INTENNUM (VA_AITC_BASE + INTENNUM_OFF) -#define IMX_AITC_INTDISNUM (VA_AITC_BASE + INTDISNUM_OFF) -#define IMX_AITC_INTENABLEH (VA_AITC_BASE + INTENABLEH_OFF) -#define IMX_AITC_INTENABLEL (VA_AITC_BASE + INTENABLEL_OFF) -#define IMX_AITC_INTTYPEH (VA_AITC_BASE + INTTYPEH_OFF) -#define IMX_AITC_INTTYPEL (VA_AITC_BASE + INTTYPEL_OFF) -#define IMX_AITC_NIPRIORITY(x) (VA_AITC_BASE + NIPRIORITY_OFF(x)) -#define IMX_AITC_NIVECSR (VA_AITC_BASE + NIVECSR_OFF) -#define IMX_AITC_FIVECSR (VA_AITC_BASE + FIVECSR_OFF) -#define IMX_AITC_INTSRCH (VA_AITC_BASE + INTSRCH_OFF) -#define IMX_AITC_INTSRCL (VA_AITC_BASE + INTSRCL_OFF) -#define IMX_AITC_INTFRCH (VA_AITC_BASE + INTFRCH_OFF) -#define IMX_AITC_INTFRCL (VA_AITC_BASE + INTFRCL_OFF) -#define IMX_AITC_NIPNDH (VA_AITC_BASE + NIPNDH_OFF) -#define IMX_AITC_NIPNDL (VA_AITC_BASE + NIPNDL_OFF) -#define IMX_AITC_FIPNDH (VA_AITC_BASE + FIPNDH_OFF) -#define IMX_AITC_FIPNDL (VA_AITC_BASE + FIPNDL_OFF) - -#if 0 -#define DEBUG_IRQ(fmt...) printk(fmt) -#else -#define DEBUG_IRQ(fmt...) do { } while (0) -#endif - -static void -imx_mask_irq(unsigned int irq) -{ - __raw_writel(irq, IMX_AITC_INTDISNUM); -} - -static void -imx_unmask_irq(unsigned int irq) -{ - __raw_writel(irq, IMX_AITC_INTENNUM); -} - -#ifdef CONFIG_FIQ -int imx_set_irq_fiq(unsigned int irq, unsigned int type) -{ - unsigned int irqt; - - if (irq >= IMX_IRQS) - return -EINVAL; - - if (irq < IMX_IRQS / 2) { - irqt = __raw_readl(IMX_AITC_INTTYPEL) & ~(1 << irq); - __raw_writel(irqt | (!!type << irq), IMX_AITC_INTTYPEL); - } else { - irq -= IMX_IRQS / 2; - irqt = __raw_readl(IMX_AITC_INTTYPEH) & ~(1 << irq); - __raw_writel(irqt | (!!type << irq), IMX_AITC_INTTYPEH); - } - - return 0; -} -EXPORT_SYMBOL(imx_set_irq_fiq); -#endif /* CONFIG_FIQ */ - -static int -imx_gpio_irq_type(unsigned int _irq, unsigned int type) -{ - unsigned int irq_type = 0, irq, reg, bit; - - irq = _irq - IRQ_GPIOA(0); - reg = irq >> 5; - bit = 1 << (irq % 32); - - if (type == IRQ_TYPE_PROBE) { - /* Don't mess with enabled GPIOs using preconfigured edges or - GPIOs set to alternate function during probe */ - /* TODO: support probe */ -// if ((GPIO_IRQ_rising_edge[idx] | GPIO_IRQ_falling_edge[idx]) & -// GPIO_bit(gpio)) -// return 0; -// if (GAFR(gpio) & (0x3 << (((gpio) & 0xf)*2))) -// return 0; -// type = IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING; - } - - GIUS(reg) |= bit; - DDIR(reg) &= ~(bit); - - DEBUG_IRQ("setting type of irq %d to ", _irq); - - if (type & IRQ_TYPE_EDGE_RISING) { - DEBUG_IRQ("rising edges\n"); - irq_type = 0x0; - } - if (type & IRQ_TYPE_EDGE_FALLING) { - DEBUG_IRQ("falling edges\n"); - irq_type = 0x1; - } - if (type & IRQ_TYPE_LEVEL_LOW) { - DEBUG_IRQ("low level\n"); - irq_type = 0x3; - } - if (type & IRQ_TYPE_LEVEL_HIGH) { - DEBUG_IRQ("high level\n"); - irq_type = 0x2; - } - - if (irq % 32 < 16) { - ICR1(reg) = (ICR1(reg) & ~(0x3 << ((irq % 16) * 2))) | - (irq_type << ((irq % 16) * 2)); - } else { - ICR2(reg) = (ICR2(reg) & ~(0x3 << ((irq % 16) * 2))) | - (irq_type << ((irq % 16) * 2)); - } - - return 0; - -} - -static void -imx_gpio_ack_irq(unsigned int irq) -{ - DEBUG_IRQ("%s: irq %d\n", __func__, irq); - ISR(IRQ_TO_REG(irq)) = 1 << ((irq - IRQ_GPIOA(0)) % 32); -} - -static void -imx_gpio_mask_irq(unsigned int irq) -{ - DEBUG_IRQ("%s: irq %d\n", __func__, irq); - IMR(IRQ_TO_REG(irq)) &= ~( 1 << ((irq - IRQ_GPIOA(0)) % 32)); -} - -static void -imx_gpio_unmask_irq(unsigned int irq) -{ - DEBUG_IRQ("%s: irq %d\n", __func__, irq); - IMR(IRQ_TO_REG(irq)) |= 1 << ((irq - IRQ_GPIOA(0)) % 32); -} - -static void -imx_gpio_handler(unsigned int mask, unsigned int irq, - struct irq_desc *desc) -{ - while (mask) { - if (mask & 1) { - DEBUG_IRQ("handling irq %d\n", irq); - generic_handle_irq(irq); - } - irq++; - mask >>= 1; - } -} - -static void -imx_gpioa_demux_handler(unsigned int irq_unused, struct irq_desc *desc) -{ - unsigned int mask, irq; - - mask = ISR(0); - irq = IRQ_GPIOA(0); - imx_gpio_handler(mask, irq, desc); -} - -static void -imx_gpiob_demux_handler(unsigned int irq_unused, struct irq_desc *desc) -{ - unsigned int mask, irq; - - mask = ISR(1); - irq = IRQ_GPIOB(0); - imx_gpio_handler(mask, irq, desc); -} - -static void -imx_gpioc_demux_handler(unsigned int irq_unused, struct irq_desc *desc) -{ - unsigned int mask, irq; - - mask = ISR(2); - irq = IRQ_GPIOC(0); - imx_gpio_handler(mask, irq, desc); -} - -static void -imx_gpiod_demux_handler(unsigned int irq_unused, struct irq_desc *desc) -{ - unsigned int mask, irq; - - mask = ISR(3); - irq = IRQ_GPIOD(0); - imx_gpio_handler(mask, irq, desc); -} - -static struct irq_chip imx_internal_chip = { - .name = "MPU", - .ack = imx_mask_irq, - .mask = imx_mask_irq, - .unmask = imx_unmask_irq, -}; - -static struct irq_chip imx_gpio_chip = { - .name = "GPIO", - .ack = imx_gpio_ack_irq, - .mask = imx_gpio_mask_irq, - .unmask = imx_gpio_unmask_irq, - .set_type = imx_gpio_irq_type, -}; - -void __init -imx_init_irq(void) -{ - unsigned int irq; - - DEBUG_IRQ("Initializing imx interrupts\n"); - - /* Disable all interrupts initially. */ - /* Do not rely on the bootloader. */ - __raw_writel(0, IMX_AITC_INTENABLEH); - __raw_writel(0, IMX_AITC_INTENABLEL); - - /* Mask all GPIO interrupts as well */ - IMR(0) = 0; - IMR(1) = 0; - IMR(2) = 0; - IMR(3) = 0; - - for (irq = 0; irq < IMX_IRQS; irq++) { - set_irq_chip(irq, &imx_internal_chip); - set_irq_handler(irq, handle_level_irq); - set_irq_flags(irq, IRQF_VALID); - } - - for (irq = IRQ_GPIOA(0); irq < IRQ_GPIOD(32); irq++) { - set_irq_chip(irq, &imx_gpio_chip); - set_irq_handler(irq, handle_edge_irq); - set_irq_flags(irq, IRQF_VALID); - } - - set_irq_chained_handler(GPIO_INT_PORTA, imx_gpioa_demux_handler); - set_irq_chained_handler(GPIO_INT_PORTB, imx_gpiob_demux_handler); - set_irq_chained_handler(GPIO_INT_PORTC, imx_gpioc_demux_handler); - set_irq_chained_handler(GPIO_INT_PORTD, imx_gpiod_demux_handler); - - /* Release masking of interrupts according to priority */ - __raw_writel(-1, IMX_AITC_NIMASK); - -#ifdef CONFIG_FIQ - /* Initialize FIQ */ - init_FIQ(); -#endif -} diff --git a/arch/arm/mach-imx/leds-mx1ads.c b/arch/arm/mach-imx/leds-mx1ads.c deleted file mode 100644 index 1d48f2762cb..00000000000 --- a/arch/arm/mach-imx/leds-mx1ads.c +++ /dev/null @@ -1,53 +0,0 @@ -/* - * linux/arch/arm/mach-imx/leds-mx1ads.c - * - * Copyright (c) 2004 Sascha Hauer <sascha@saschahauer.de> - * - * Original (leds-footbridge.c) by Russell King - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/io.h> -#include <mach/hardware.h> -#include <asm/system.h> -#include <asm/leds.h> -#include "leds.h" - -/* - * The MX1ADS Board has only one usable LED, - * so select only the timer led or the - * cpu usage led - */ -void -mx1ads_leds_event(led_event_t ledevt) -{ - unsigned long flags; - - local_irq_save(flags); - - switch (ledevt) { -#ifdef CONFIG_LEDS_CPU - case led_idle_start: - DR(0) &= ~(1<<2); - break; - - case led_idle_end: - DR(0) |= 1<<2; - break; -#endif - -#ifdef CONFIG_LEDS_TIMER - case led_timer: - DR(0) ^= 1<<2; -#endif - default: - break; - } - local_irq_restore(flags); -} diff --git a/arch/arm/mach-imx/leds.c b/arch/arm/mach-imx/leds.c deleted file mode 100644 index cf30803e019..00000000000 --- a/arch/arm/mach-imx/leds.c +++ /dev/null @@ -1,31 +0,0 @@ -/* - * linux/arch/arm/mach-imx/leds.c - * - * Copyright (C) 2004 Sascha Hauer <sascha@saschahauer.de> - * - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ - -#include <linux/kernel.h> -#include <linux/init.h> - -#include <asm/leds.h> -#include <asm/mach-types.h> - -#include "leds.h" - -static int __init -leds_init(void) -{ - if (machine_is_mx1ads()) { - leds_event = mx1ads_leds_event; - } - - return 0; -} - -__initcall(leds_init); diff --git a/arch/arm/mach-imx/leds.h b/arch/arm/mach-imx/leds.h deleted file mode 100644 index 49dc1c1da33..00000000000 --- a/arch/arm/mach-imx/leds.h +++ /dev/null @@ -1,9 +0,0 @@ -/* - * arch/arm/mach-imx/leds.h - * - * Copyright (c) 2004 Sascha Hauer <sascha@saschahauer.de> - * - * blinky lights for IMX-based systems - * - */ -extern void mx1ads_leds_event(led_event_t evt); diff --git a/arch/arm/mach-imx/mx1ads.c b/arch/arm/mach-imx/mx1ads.c deleted file mode 100644 index 87fa1ff43b0..00000000000 --- a/arch/arm/mach-imx/mx1ads.c +++ /dev/null @@ -1,180 +0,0 @@ -/* - * arch/arm/mach-imx/mx1ads.c - * - * Initially based on: - * linux-2.6.7-imx/arch/arm/mach-imx/scb9328.c - * Copyright (c) 2004 Sascha Hauer <sascha@saschahauer.de> - * - * 2004 (c) MontaVista Software, Inc. - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - */ - -#include <linux/device.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <asm/system.h> -#include <mach/hardware.h> -#include <asm/irq.h> -#include <asm/pgtable.h> -#include <asm/page.h> - -#include <asm/mach/map.h> -#include <asm/mach-types.h> - -#include <asm/mach/arch.h> -#include <mach/mmc.h> -#include <mach/imx-uart.h> -#include <linux/interrupt.h> -#include "generic.h" - -static struct resource cs89x0_resources[] = { - [0] = { - .start = IMX_CS4_PHYS + 0x300, - .end = IMX_CS4_PHYS + 0x300 + 16, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_GPIOC(17), - .end = IRQ_GPIOC(17), - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device cs89x0_device = { - .name = "cirrus-cs89x0", - .num_resources = ARRAY_SIZE(cs89x0_resources), - .resource = cs89x0_resources, -}; - -static struct imxuart_platform_data uart_pdata = { - .flags = IMXUART_HAVE_RTSCTS, -}; - -static struct resource imx_uart1_resources[] = { - [0] = { - .start = 0x00206000, - .end = 0x002060FF, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = (UART1_MINT_RX), - .end = (UART1_MINT_RX), - .flags = IORESOURCE_IRQ, - }, - [2] = { - .start = (UART1_MINT_TX), - .end = (UART1_MINT_TX), - .flags = IORESOURCE_IRQ, - }, - [3] = { - .start = UART1_MINT_RTS, - .end = UART1_MINT_RTS, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device imx_uart1_device = { - .name = "imx-uart", - .id = 0, - .num_resources = ARRAY_SIZE(imx_uart1_resources), - .resource = imx_uart1_resources, - .dev = { - .platform_data = &uart_pdata, - } -}; - -static struct resource imx_uart2_resources[] = { - [0] = { - .start = 0x00207000, - .end = 0x002070FF, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = (UART2_MINT_RX), - .end = (UART2_MINT_RX), - .flags = IORESOURCE_IRQ, - }, - [2] = { - .start = (UART2_MINT_TX), - .end = (UART2_MINT_TX), - .flags = IORESOURCE_IRQ, - }, - [3] = { - .start = UART2_MINT_RTS, - .end = UART2_MINT_RTS, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device imx_uart2_device = { - .name = "imx-uart", - .id = 1, - .num_resources = ARRAY_SIZE(imx_uart2_resources), - .resource = imx_uart2_resources, - .dev = { - .platform_data = &uart_pdata, - } -}; - -static struct platform_device *devices[] __initdata = { - &cs89x0_device, - &imx_uart1_device, - &imx_uart2_device, -}; - -#if defined(CONFIG_MMC_IMX) || defined(CONFIG_MMC_IMX_MODULE) -static int mx1ads_mmc_card_present(struct device *dev) -{ - /* MMC/SD Card Detect is PB 20 on MX1ADS V1.0.7 */ - return (SSR(1) & (1 << 20) ? 0 : 1); -} - -static struct imxmmc_platform_data mx1ads_mmc_info = { - .card_present = mx1ads_mmc_card_present, -}; -#endif - -static void __init -mx1ads_init(void) -{ -#ifdef CONFIG_LEDS - imx_gpio_mode(GPIO_PORTA | GPIO_OUT | 2); -#endif -#if defined(CONFIG_MMC_IMX) || defined(CONFIG_MMC_IMX_MODULE) - /* SD/MMC card detect */ - imx_gpio_mode(GPIO_PORTB | GPIO_GIUS | GPIO_IN | 20); - imx_set_mmc_info(&mx1ads_mmc_info); -#endif - - imx_gpio_mode(PC9_PF_UART1_CTS); - imx_gpio_mode(PC10_PF_UART1_RTS); - imx_gpio_mode(PC11_PF_UART1_TXD); - imx_gpio_mode(PC12_PF_UART1_RXD); - - imx_gpio_mode(PB28_PF_UART2_CTS); - imx_gpio_mode(PB29_PF_UART2_RTS); - imx_gpio_mode(PB30_PF_UART2_TXD); - imx_gpio_mode(PB31_PF_UART2_RXD); - - platform_add_devices(devices, ARRAY_SIZE(devices)); -} - -static void __init -mx1ads_map_io(void) -{ - imx_map_io(); -} - -MACHINE_START(MX1ADS, "Motorola MX1ADS") - /* Maintainer: Sascha Hauer, Pengutronix */ - .phys_io = 0x00200000, - .io_pg_offst = ((0xe0000000) >> 18) & 0xfffc, - .boot_params = 0x08000100, - .map_io = mx1ads_map_io, - .init_irq = imx_init_irq, - .timer = &imx_timer, - .init_machine = mx1ads_init, -MACHINE_END diff --git a/arch/arm/mach-imx/time.c b/arch/arm/mach-imx/time.c deleted file mode 100644 index 5aef18b599e..00000000000 --- a/arch/arm/mach-imx/time.c +++ /dev/null @@ -1,220 +0,0 @@ -/* - * linux/arch/arm/mach-imx/time.c - * - * Copyright (C) 2000-2001 Deep Blue Solutions - * Copyright (C) 2002 Shane Nay (shane@minirl.com) - * Copyright (C) 2006-2007 Pavel Pisa (ppisa@pikron.com) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/time.h> -#include <linux/clocksource.h> -#include <linux/clockchips.h> -#include <linux/clk.h> -#include <linux/io.h> - -#include <mach/hardware.h> -#include <asm/leds.h> -#include <asm/irq.h> -#include <asm/mach/time.h> - -/* Use timer 1 as system timer */ -#define TIMER_BASE IMX_TIM1_BASE - -static struct clock_event_device clockevent_imx; -static enum clock_event_mode clockevent_mode = CLOCK_EVT_MODE_UNUSED; - -/* - * IRQ handler for the timer - */ -static irqreturn_t -imx_timer_interrupt(int irq, void *dev_id) -{ - struct clock_event_device *evt = &clockevent_imx; - uint32_t tstat; - irqreturn_t ret = IRQ_NONE; - - /* clear the interrupt */ - tstat = IMX_TSTAT(TIMER_BASE); - IMX_TSTAT(TIMER_BASE) = 0; - - if (tstat & TSTAT_COMP) { - evt->event_handler(evt); - ret = IRQ_HANDLED; - } - - return ret; -} - -static struct irqaction imx_timer_irq = { - .name = "i.MX Timer Tick", - .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL, - .handler = imx_timer_interrupt, -}; - -/* - * Set up timer hardware into expected mode and state. - */ -static void __init imx_timer_hardware_init(void) -{ - /* - * Initialise to a known state (all timers off, and timing reset) - */ - IMX_TCTL(TIMER_BASE) = 0; - IMX_TPRER(TIMER_BASE) = 0; - - IMX_TCTL(TIMER_BASE) = TCTL_FRR | TCTL_CLK_PCLK1 | TCTL_TEN; -} - -cycle_t imx_get_cycles(struct clocksource *cs) -{ - return IMX_TCN(TIMER_BASE); -} - -static struct clocksource clocksource_imx = { - .name = "imx_timer1", - .rating = 200, - .read = imx_get_cycles, - .mask = 0xFFFFFFFF, - .shift = 20, - .flags = CLOCK_SOURCE_IS_CONTINUOUS, -}; - -static int __init imx_clocksource_init(unsigned long rate) -{ - clocksource_imx.mult = - clocksource_hz2mult(rate, clocksource_imx.shift); - clocksource_register(&clocksource_imx); - - return 0; -} - -static int imx_set_next_event(unsigned long evt, - struct clock_event_device *unused) -{ - unsigned long tcmp; - - tcmp = IMX_TCN(TIMER_BASE) + evt; - IMX_TCMP(TIMER_BASE) = tcmp; - - return (int32_t)(tcmp - IMX_TCN(TIMER_BASE)) < 0 ? -ETIME : 0; -} - -#ifdef DEBUG -static const char *clock_event_mode_label[]={ - [CLOCK_EVT_MODE_PERIODIC] = "CLOCK_EVT_MODE_PERIODIC", - [CLOCK_EVT_MODE_ONESHOT] = "CLOCK_EVT_MODE_ONESHOT", - [CLOCK_EVT_MODE_SHUTDOWN] = "CLOCK_EVT_MODE_SHUTDOWN", - [CLOCK_EVT_MODE_UNUSED] = "CLOCK_EVT_MODE_UNUSED" -}; -#endif /*DEBUG*/ - -static void imx_set_mode(enum clock_event_mode mode, struct clock_event_device *evt) -{ - unsigned long flags; - - /* - * The timer interrupt generation is disabled at least - * for enough time to call imx_set_next_event() - */ - local_irq_save(flags); - /* Disable interrupt in GPT module */ - IMX_TCTL(TIMER_BASE) &= ~TCTL_IRQEN; - if (mode != clockevent_mode) { - /* Set event time into far-far future */ - IMX_TCMP(TIMER_BASE) = IMX_TCN(TIMER_BASE) - 3; - /* Clear pending interrupt */ - IMX_TSTAT(TIMER_BASE) &= ~TSTAT_COMP; - } - -#ifdef DEBUG - printk(KERN_INFO "imx_set_mode: changing mode from %s to %s\n", - clock_event_mode_label[clockevent_mode], clock_event_mode_label[mode]); -#endif /*DEBUG*/ - - /* Remember timer mode */ - clockevent_mode = mode; - local_irq_restore(flags); - - switch (mode) { - case CLOCK_EVT_MODE_PERIODIC: - printk(KERN_ERR "imx_set_mode: Periodic mode is not supported for i.MX\n"); - break; - case CLOCK_EVT_MODE_ONESHOT: - /* - * Do not put overhead of interrupt enable/disable into - * imx_set_next_event(), the core has about 4 minutes - * to call imx_set_next_event() or shutdown clock after - * mode switching - */ - local_irq_save(flags); - IMX_TCTL(TIMER_BASE) |= TCTL_IRQEN; - local_irq_restore(flags); - break; - case CLOCK_EVT_MODE_SHUTDOWN: - case CLOCK_EVT_MODE_UNUSED: - case CLOCK_EVT_MODE_RESUME: - /* Left event sources disabled, no more interrupts appears */ - break; - } -} - -static struct clock_event_device clockevent_imx = { - .name = "imx_timer1", - .features = CLOCK_EVT_FEAT_ONESHOT, - .shift = 32, - .set_mode = imx_set_mode, - .set_next_event = imx_set_next_event, - .rating = 200, -}; - -static int __init imx_clockevent_init(unsigned long rate) -{ - clockevent_imx.mult = div_sc(rate, NSEC_PER_SEC, - clockevent_imx.shift); - clockevent_imx.max_delta_ns = - clockevent_delta2ns(0xfffffffe, &clockevent_imx); - clockevent_imx.min_delta_ns = - clockevent_delta2ns(0xf, &clockevent_imx); - - clockevent_imx.cpumask = cpumask_of(0); - - clockevents_register_device(&clockevent_imx); - - return 0; -} - -extern int imx_clocks_init(void); - -static void __init imx_timer_init(void) -{ - struct clk *clk; - unsigned long rate; - - imx_clocks_init(); - - clk = clk_get(NULL, "perclk1"); - clk_enable(clk); - rate = clk_get_rate(clk); - - imx_timer_hardware_init(); - imx_clocksource_init(rate); - - imx_clockevent_init(rate); - - /* - * Make irqs happen for the system timer - */ - setup_irq(TIM1_INT, &imx_timer_irq); -} - -struct sys_timer imx_timer = { - .init = imx_timer_init, -}; diff --git a/arch/arm/mach-mx1/generic.c b/arch/arm/mach-mx1/generic.c index 0dec6f300ff..7622c9b38c9 100644 --- a/arch/arm/mach-mx1/generic.c +++ b/arch/arm/mach-mx1/generic.c @@ -26,6 +26,7 @@ #include <asm/mach/map.h> +#include <mach/common.h> #include <mach/hardware.h> static struct map_desc imx_io_desc[] __initdata = { @@ -37,7 +38,9 @@ static struct map_desc imx_io_desc[] __initdata = { } }; -void __init mxc_map_io(void) +void __init mx1_map_io(void) { + mxc_set_cpu_type(MXC_CPU_MX1); + iotable_init(imx_io_desc, ARRAY_SIZE(imx_io_desc)); } diff --git a/arch/arm/mach-mx1/mx1ads.c b/arch/arm/mach-mx1/mx1ads.c index e54057fb855..e5b0c0a83c3 100644 --- a/arch/arm/mach-mx1/mx1ads.c +++ b/arch/arm/mach-mx1/mx1ads.c @@ -12,77 +12,56 @@ * warranty of any kind, whether express or implied. */ -#include <linux/kernel.h> +#include <linux/i2c.h> +#include <linux/i2c/pcf857x.h> #include <linux/init.h> +#include <linux/kernel.h> #include <linux/platform_device.h> #include <linux/mtd/physmap.h> -#include <linux/i2c.h> -#include <linux/i2c/pcf857x.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <asm/mach/time.h> -#include <mach/irqs.h> -#include <mach/hardware.h> #include <mach/common.h> -#include <mach/imx-uart.h> -#include <mach/irqs.h> +#include <mach/hardware.h> #include <mach/i2c.h> +#include <mach/imx-uart.h> #include <mach/iomux.h> +#include <mach/irqs.h> + #include "devices.h" -/* - * UARTs platform data - */ -static int mxc_uart1_pins[] = { +static int mx1ads_pins[] = { + /* UART1 */ PC9_PF_UART1_CTS, PC10_PF_UART1_RTS, PC11_PF_UART1_TXD, PC12_PF_UART1_RXD, -}; - -static int uart1_mxc_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_uart1_pins, - ARRAY_SIZE(mxc_uart1_pins), "UART1"); -} - -static int uart1_mxc_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart1_pins, - ARRAY_SIZE(mxc_uart1_pins)); - return 0; -} - -static int mxc_uart2_pins[] = { + /* UART2 */ PB28_PF_UART2_CTS, PB29_PF_UART2_RTS, PB30_PF_UART2_TXD, PB31_PF_UART2_RXD, + /* I2C */ + PA15_PF_I2C_SDA, + PA16_PF_I2C_SCL, + /* SPI */ + PC13_PF_SPI1_SPI_RDY, + PC14_PF_SPI1_SCLK, + PC15_PF_SPI1_SS, + PC16_PF_SPI1_MISO, + PC17_PF_SPI1_MOSI, }; -static int uart2_mxc_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_uart2_pins, - ARRAY_SIZE(mxc_uart2_pins), "UART2"); -} - -static int uart2_mxc_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart2_pins, - ARRAY_SIZE(mxc_uart2_pins)); - return 0; -} +/* + * UARTs platform data + */ static struct imxuart_platform_data uart_pdata[] = { { - .init = uart1_mxc_init, - .exit = uart1_mxc_exit, .flags = IMXUART_HAVE_RTSCTS, }, { - .init = uart2_mxc_init, - .exit = uart2_mxc_exit, .flags = IMXUART_HAVE_RTSCTS, }, }; @@ -111,24 +90,6 @@ static struct platform_device flash_device = { /* * I2C */ - -static int i2c_pins[] = { - PA15_PF_I2C_SDA, - PA16_PF_I2C_SCL, -}; - -static int i2c_init(struct device *dev) -{ - return mxc_gpio_setup_multiple_pins(i2c_pins, - ARRAY_SIZE(i2c_pins), "I2C"); -} - -static void i2c_exit(struct device *dev) -{ - mxc_gpio_release_multiple_pins(i2c_pins, - ARRAY_SIZE(i2c_pins)); -} - static struct pcf857x_platform_data pcf857x_data[] = { { .gpio_base = 4 * 32, @@ -139,8 +100,6 @@ static struct pcf857x_platform_data pcf857x_data[] = { static struct imxi2c_platform_data mx1ads_i2c_data = { .bitrate = 100000, - .init = i2c_init, - .exit = i2c_exit, }; static struct i2c_board_info mx1ads_i2c_devices[] = { @@ -160,6 +119,9 @@ static struct i2c_board_info mx1ads_i2c_devices[] = { */ static void __init mx1ads_init(void) { + mxc_gpio_setup_multiple_pins(mx1ads_pins, + ARRAY_SIZE(mx1ads_pins), "mx1ads"); + /* UART */ mxc_register_device(&imx_uart1_device, &uart_pdata[0]); mxc_register_device(&imx_uart2_device, &uart_pdata[1]); @@ -188,7 +150,7 @@ MACHINE_START(MX1ADS, "Freescale MX1ADS") .phys_io = IMX_IO_PHYS, .io_pg_offst = (IMX_IO_BASE >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x100, - .map_io = mxc_map_io, + .map_io = mx1_map_io, .init_irq = mxc_init_irq, .timer = &mx1ads_timer, .init_machine = mx1ads_init, @@ -198,7 +160,7 @@ MACHINE_START(MXLADS, "Freescale MXLADS") .phys_io = IMX_IO_PHYS, .io_pg_offst = (IMX_IO_BASE >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x100, - .map_io = mxc_map_io, + .map_io = mx1_map_io, .init_irq = mxc_init_irq, .timer = &mx1ads_timer, .init_machine = mx1ads_init, diff --git a/arch/arm/mach-mx1/scb9328.c b/arch/arm/mach-mx1/scb9328.c index 0e71f3fa28b..20e0b5bcdff 100644 --- a/arch/arm/mach-mx1/scb9328.c +++ b/arch/arm/mach-mx1/scb9328.c @@ -153,7 +153,7 @@ MACHINE_START(SCB9328, "Synertronixx scb9328") .phys_io = 0x00200000, .io_pg_offst = ((0xe0200000) >> 18) & 0xfffc, .boot_params = 0x08000100, - .map_io = mxc_map_io, + .map_io = mx1_map_io, .init_irq = mxc_init_irq, .timer = &scb9328_timer, .init_machine = scb9328_init, diff --git a/arch/arm/mach-mx2/Kconfig b/arch/arm/mach-mx2/Kconfig index 42a788842f4..61550443a23 100644 --- a/arch/arm/mach-mx2/Kconfig +++ b/arch/arm/mach-mx2/Kconfig @@ -18,6 +18,13 @@ endchoice comment "MX2 platforms:" +config MACH_MX21ADS + bool "MX21ADS platform" + depends on MACH_MX21 + help + Include support for MX21ADS platform. This includes specific + configurations for the board and its peripherals. + config MACH_MX27ADS bool "MX27ADS platform" depends on MACH_MX27 @@ -46,4 +53,10 @@ config MACH_PCM970_BASEBOARD endchoice +config MACH_MX27_3DS + bool "MX27PDK platform" + depends on MACH_MX27 + help + Include support for MX27PDK platform. This includes specific + configurations for the board and its peripherals. endif diff --git a/arch/arm/mach-mx2/Makefile b/arch/arm/mach-mx2/Makefile index 950649a9154..d140e2dcf94 100644 --- a/arch/arm/mach-mx2/Makefile +++ b/arch/arm/mach-mx2/Makefile @@ -11,6 +11,8 @@ obj-$(CONFIG_MACH_MX21) += clock_imx21.o obj-$(CONFIG_MACH_MX27) += cpu_imx27.o obj-$(CONFIG_MACH_MX27) += clock_imx27.o +obj-$(CONFIG_MACH_MX21ADS) += mx21ads.o obj-$(CONFIG_MACH_MX27ADS) += mx27ads.o obj-$(CONFIG_MACH_PCM038) += pcm038.o obj-$(CONFIG_MACH_PCM970_BASEBOARD) += pcm970-baseboard.o +obj-$(CONFIG_MACH_MX27_3DS) += mx27pdk.o diff --git a/arch/arm/mach-mx2/generic.c b/arch/arm/mach-mx2/generic.c index bd51dd04948..169372f69d8 100644 --- a/arch/arm/mach-mx2/generic.c +++ b/arch/arm/mach-mx2/generic.c @@ -69,7 +69,17 @@ static struct map_desc mxc_io_desc[] __initdata = { * system startup to create static physical to virtual * memory map for the IO modules. */ -void __init mxc_map_io(void) +void __init mx21_map_io(void) { + mxc_set_cpu_type(MXC_CPU_MX21); + iotable_init(mxc_io_desc, ARRAY_SIZE(mxc_io_desc)); } + +void __init mx27_map_io(void) +{ + mxc_set_cpu_type(MXC_CPU_MX27); + + iotable_init(mxc_io_desc, ARRAY_SIZE(mxc_io_desc)); +} + diff --git a/arch/arm/mach-mx2/mx21ads.c b/arch/arm/mach-mx2/mx21ads.c new file mode 100644 index 00000000000..a5ee461cb40 --- /dev/null +++ b/arch/arm/mach-mx2/mx21ads.c @@ -0,0 +1,286 @@ +/* + * Copyright (C) 2000 Deep Blue Solutions Ltd + * Copyright (C) 2002 Shane Nay (shane@minirl.com) + * Copyright 2006-2007 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/physmap.h> +#include <linux/gpio.h> +#include <mach/common.h> +#include <mach/hardware.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <asm/mach/map.h> +#include <mach/imx-uart.h> +#include <mach/imxfb.h> +#include <mach/iomux.h> +#include <mach/mxc_nand.h> +#include <mach/mmc.h> +#include <mach/board-mx21ads.h> + +#include "devices.h" + +static unsigned int mx21ads_pins[] = { + + /* CS8900A */ + (GPIO_PORTE | GPIO_GPIO | GPIO_IN | 11), + + /* UART1 */ + PE12_PF_UART1_TXD, + PE13_PF_UART1_RXD, + PE14_PF_UART1_CTS, + PE15_PF_UART1_RTS, + + /* UART3 (IrDA) - only TXD and RXD */ + PE8_PF_UART3_TXD, + PE9_PF_UART3_RXD, + + /* UART4 */ + PB26_AF_UART4_RTS, + PB28_AF_UART4_TXD, + PB29_AF_UART4_CTS, + PB31_AF_UART4_RXD, + + /* LCDC */ + PA5_PF_LSCLK, + PA6_PF_LD0, + PA7_PF_LD1, + PA8_PF_LD2, + PA9_PF_LD3, + PA10_PF_LD4, + PA11_PF_LD5, + PA12_PF_LD6, + PA13_PF_LD7, + PA14_PF_LD8, + PA15_PF_LD9, + PA16_PF_LD10, + PA17_PF_LD11, + PA18_PF_LD12, + PA19_PF_LD13, + PA20_PF_LD14, + PA21_PF_LD15, + PA22_PF_LD16, + PA24_PF_REV, /* Sharp panel dedicated signal */ + PA25_PF_CLS, /* Sharp panel dedicated signal */ + PA26_PF_PS, /* Sharp panel dedicated signal */ + PA27_PF_SPL_SPR, /* Sharp panel dedicated signal */ + PA28_PF_HSYNC, + PA29_PF_VSYNC, + PA30_PF_CONTRAST, + PA31_PF_OE_ACD, + + /* MMC/SDHC */ + PE18_PF_SD1_D0, + PE19_PF_SD1_D1, + PE20_PF_SD1_D2, + PE21_PF_SD1_D3, + PE22_PF_SD1_CMD, + PE23_PF_SD1_CLK, + + /* NFC */ + PF0_PF_NRFB, + PF1_PF_NFCE, + PF2_PF_NFWP, + PF3_PF_NFCLE, + PF4_PF_NFALE, + PF5_PF_NFRE, + PF6_PF_NFWE, + PF7_PF_NFIO0, + PF8_PF_NFIO1, + PF9_PF_NFIO2, + PF10_PF_NFIO3, + PF11_PF_NFIO4, + PF12_PF_NFIO5, + PF13_PF_NFIO6, + PF14_PF_NFIO7, +}; + +/* ADS's NOR flash: 2x AM29BDS128HE9VKI on 32-bit bus */ +static struct physmap_flash_data mx21ads_flash_data = { + .width = 4, +}; + +static struct resource mx21ads_flash_resource = { + .start = CS0_BASE_ADDR, + .end = CS0_BASE_ADDR + 0x02000000 - 1, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device mx21ads_nor_mtd_device = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &mx21ads_flash_data, + }, + .num_resources = 1, + .resource = &mx21ads_flash_resource, +}; + +static struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +static struct imxuart_platform_data uart_norts_pdata = { +}; + + +static int mx21ads_fb_init(struct platform_device *pdev) +{ + u16 tmp; + + tmp = __raw_readw(MX21ADS_IO_REG); + tmp |= MX21ADS_IO_LCDON; + __raw_writew(tmp, MX21ADS_IO_REG); + return 0; +} + +static void mx21ads_fb_exit(struct platform_device *pdev) +{ + u16 tmp; + + tmp = __raw_readw(MX21ADS_IO_REG); + tmp &= ~MX21ADS_IO_LCDON; + __raw_writew(tmp, MX21ADS_IO_REG); +} + +/* + * Connected is a portrait Sharp-QVGA display + * of type: LQ035Q7DB02 + */ +static struct imx_fb_platform_data mx21ads_fb_data = { + .pixclock = 188679, /* in ps */ + .xres = 240, + .yres = 320, + + .bpp = 16, + .hsync_len = 2, + .left_margin = 6, + .right_margin = 16, + + .vsync_len = 1, + .upper_margin = 8, + .lower_margin = 10, + .fixed_screen_cpu = 0, + + .pcr = 0xFB108BC7, + .pwmr = 0x00A901ff, + .lscr1 = 0x00120300, + .dmacr = 0x00020008, + + .init = mx21ads_fb_init, + .exit = mx21ads_fb_exit, +}; + +static int mx21ads_sdhc_get_ro(struct device *dev) +{ + return (__raw_readw(MX21ADS_IO_REG) & MX21ADS_IO_SD_WP) ? 1 : 0; +} + +static int mx21ads_sdhc_init(struct device *dev, irq_handler_t detect_irq, + void *data) +{ + int ret; + + ret = request_irq(IRQ_GPIOD(25), detect_irq, + IRQF_TRIGGER_FALLING, "mmc-detect", data); + if (ret) + goto out; + return 0; +out: + return ret; +} + +static void mx21ads_sdhc_exit(struct device *dev, void *data) +{ + free_irq(IRQ_GPIOD(25), data); +} + +static struct imxmmc_platform_data mx21ads_sdhc_pdata = { + .ocr_avail = MMC_VDD_29_30 | MMC_VDD_30_31, /* 3.0V */ + .get_ro = mx21ads_sdhc_get_ro, + .init = mx21ads_sdhc_init, + .exit = mx21ads_sdhc_exit, +}; + +static struct mxc_nand_platform_data mx21ads_nand_board_info = { + .width = 1, + .hw_ecc = 1, +}; + +static struct map_desc mx21ads_io_desc[] __initdata = { + /* + * Memory-mapped I/O on MX21ADS Base board: + * - CS8900A Ethernet controller + * - ST16C2552CJ UART + * - CPU and Base board version + * - Base board I/O register + */ + { + .virtual = MX21ADS_MMIO_BASE_ADDR, + .pfn = __phys_to_pfn(CS1_BASE_ADDR), + .length = MX21ADS_MMIO_SIZE, + .type = MT_DEVICE, + }, +}; + +static void __init mx21ads_map_io(void) +{ + mx21_map_io(); + iotable_init(mx21ads_io_desc, ARRAY_SIZE(mx21ads_io_desc)); +} + +static struct platform_device *platform_devices[] __initdata = { + &mx21ads_nor_mtd_device, +}; + +static void __init mx21ads_board_init(void) +{ + mxc_gpio_setup_multiple_pins(mx21ads_pins, ARRAY_SIZE(mx21ads_pins), + "mx21ads"); + + mxc_register_device(&mxc_uart_device0, &uart_pdata); + mxc_register_device(&mxc_uart_device2, &uart_norts_pdata); + mxc_register_device(&mxc_uart_device3, &uart_pdata); + mxc_register_device(&mxc_fb_device, &mx21ads_fb_data); + mxc_register_device(&mxc_sdhc_device0, &mx21ads_sdhc_pdata); + mxc_register_device(&mxc_nand_device, &mx21ads_nand_board_info); + + platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); +} + +static void __init mx21ads_timer_init(void) +{ + mx21_clocks_init(32768, 26000000); +} + +static struct sys_timer mx21ads_timer = { + .init = mx21ads_timer_init, +}; + +MACHINE_START(MX21ADS, "Freescale i.MX21ADS") + /* maintainer: Freescale Semiconductor, Inc. */ + .phys_io = AIPI_BASE_ADDR, + .io_pg_offst = ((AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, + .boot_params = PHYS_OFFSET + 0x100, + .map_io = mx21ads_map_io, + .init_irq = mxc_init_irq, + .init_machine = mx21ads_board_init, + .timer = &mx21ads_timer, +MACHINE_END diff --git a/arch/arm/mach-mx2/mx27ads.c b/arch/arm/mach-mx2/mx27ads.c index 4a3b097adc1..02daddac699 100644 --- a/arch/arm/mach-mx2/mx27ads.c +++ b/arch/arm/mach-mx2/mx27ads.c @@ -23,6 +23,8 @@ #include <linux/mtd/map.h> #include <linux/mtd/partitions.h> #include <linux/mtd/physmap.h> +#include <linux/i2c.h> +#include <linux/irq.h> #include <mach/common.h> #include <mach/hardware.h> #include <asm/mach-types.h> @@ -33,9 +35,117 @@ #include <mach/imx-uart.h> #include <mach/iomux.h> #include <mach/board-mx27ads.h> +#include <mach/mxc_nand.h> +#include <mach/i2c.h> +#include <mach/imxfb.h> +#include <mach/mmc.h> #include "devices.h" +static unsigned int mx27ads_pins[] = { + /* UART0 */ + PE12_PF_UART1_TXD, + PE13_PF_UART1_RXD, + PE14_PF_UART1_CTS, + PE15_PF_UART1_RTS, + /* UART1 */ + PE3_PF_UART2_CTS, + PE4_PF_UART2_RTS, + PE6_PF_UART2_TXD, + PE7_PF_UART2_RXD, + /* UART2 */ + PE8_PF_UART3_TXD, + PE9_PF_UART3_RXD, + PE10_PF_UART3_CTS, + PE11_PF_UART3_RTS, + /* UART3 */ + PB26_AF_UART4_RTS, + PB28_AF_UART4_TXD, + PB29_AF_UART4_CTS, + PB31_AF_UART4_RXD, + /* UART4 */ + PB18_AF_UART5_TXD, + PB19_AF_UART5_RXD, + PB20_AF_UART5_CTS, + PB21_AF_UART5_RTS, + /* UART5 */ + PB10_AF_UART6_TXD, + PB12_AF_UART6_CTS, + PB11_AF_UART6_RXD, + PB13_AF_UART6_RTS, + /* FEC */ + PD0_AIN_FEC_TXD0, + PD1_AIN_FEC_TXD1, + PD2_AIN_FEC_TXD2, + PD3_AIN_FEC_TXD3, + PD4_AOUT_FEC_RX_ER, + PD5_AOUT_FEC_RXD1, + PD6_AOUT_FEC_RXD2, + PD7_AOUT_FEC_RXD3, + PD8_AF_FEC_MDIO, + PD9_AIN_FEC_MDC, + PD10_AOUT_FEC_CRS, + PD11_AOUT_FEC_TX_CLK, + PD12_AOUT_FEC_RXD0, + PD13_AOUT_FEC_RX_DV, + PD14_AOUT_FEC_RX_CLK, + PD15_AOUT_FEC_COL, + PD16_AIN_FEC_TX_ER, + PF23_AIN_FEC_TX_EN, + /* I2C2 */ + PC5_PF_I2C2_SDA, + PC6_PF_I2C2_SCL, + /* FB */ + PA5_PF_LSCLK, + PA6_PF_LD0, + PA7_PF_LD1, + PA8_PF_LD2, + PA9_PF_LD3, + PA10_PF_LD4, + PA11_PF_LD5, + PA12_PF_LD6, + PA13_PF_LD7, + PA14_PF_LD8, + PA15_PF_LD9, + PA16_PF_LD10, + PA17_PF_LD11, + PA18_PF_LD12, + PA19_PF_LD13, + PA20_PF_LD14, + PA21_PF_LD15, + PA22_PF_LD16, + PA23_PF_LD17, + PA24_PF_REV, + PA25_PF_CLS, + PA26_PF_PS, + PA27_PF_SPL_SPR, + PA28_PF_HSYNC, + PA29_PF_VSYNC, + PA30_PF_CONTRAST, + PA31_PF_OE_ACD, + /* OWIRE */ + PE16_AF_OWIRE, + /* SDHC1*/ + PE18_PF_SD1_D0, + PE19_PF_SD1_D1, + PE20_PF_SD1_D2, + PE21_PF_SD1_D3, + PE22_PF_SD1_CMD, + PE23_PF_SD1_CLK, + /* SDHC2*/ + PB4_PF_SD2_D0, + PB5_PF_SD2_D1, + PB6_PF_SD2_D2, + PB7_PF_SD2_D3, + PB8_PF_SD2_CMD, + PB9_PF_SD2_CLK, +}; + +static struct mxc_nand_platform_data mx27ads_nand_board_info = { + .width = 1, + .hw_ecc = 1, +}; + /* ADS's NOR flash */ static struct physmap_flash_data mx27ads_flash_data = { .width = 2, @@ -58,189 +168,113 @@ static struct platform_device mx27ads_nor_mtd_device = { .resource = &mx27ads_flash_resource, }; -static int mxc_uart0_pins[] = { - PE12_PF_UART1_TXD, - PE13_PF_UART1_RXD, - PE14_PF_UART1_CTS, - PE15_PF_UART1_RTS +static struct imxi2c_platform_data mx27ads_i2c_data = { + .bitrate = 100000, }; -static int uart_mxc_port0_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_uart0_pins, - ARRAY_SIZE(mxc_uart0_pins), "UART0"); -} - -static int uart_mxc_port0_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart0_pins, - ARRAY_SIZE(mxc_uart0_pins)); - return 0; -} - -static int mxc_uart1_pins[] = { - PE3_PF_UART2_CTS, - PE4_PF_UART2_RTS, - PE6_PF_UART2_TXD, - PE7_PF_UART2_RXD +static struct i2c_board_info mx27ads_i2c_devices[] = { }; -static int uart_mxc_port1_init(struct platform_device *pdev) +void lcd_power(int on) { - return mxc_gpio_setup_multiple_pins(mxc_uart1_pins, - ARRAY_SIZE(mxc_uart1_pins), "UART1"); + if (on) + __raw_writew(PBC_BCTRL1_LCDON, PBC_BCTRL1_SET_REG); + else + __raw_writew(PBC_BCTRL1_LCDON, PBC_BCTRL1_CLEAR_REG); } -static int uart_mxc_port1_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart1_pins, - ARRAY_SIZE(mxc_uart1_pins)); - return 0; -} - -static int mxc_uart2_pins[] = { - PE8_PF_UART3_TXD, - PE9_PF_UART3_RXD, - PE10_PF_UART3_CTS, - PE11_PF_UART3_RTS +static struct imx_fb_platform_data mx27ads_fb_data = { + .pixclock = 188679, + .xres = 240, + .yres = 320, + + .bpp = 16, + .hsync_len = 1, + .left_margin = 9, + .right_margin = 16, + + .vsync_len = 1, + .upper_margin = 7, + .lower_margin = 9, + .fixed_screen_cpu = 0, + + /* + * - HSYNC active high + * - VSYNC active high + * - clk notenabled while idle + * - clock inverted + * - data not inverted + * - data enable low active + * - enable sharp mode + */ + .pcr = 0xFB008BC0, + .pwmr = 0x00A903FF, + .lscr1 = 0x00120300, + .dmacr = 0x00020010, + + .lcd_power = lcd_power, }; -static int uart_mxc_port2_init(struct platform_device *pdev) +static int mx27ads_sdhc1_init(struct device *dev, irq_handler_t detect_irq, + void *data) { - return mxc_gpio_setup_multiple_pins(mxc_uart2_pins, - ARRAY_SIZE(mxc_uart2_pins), "UART2"); + return request_irq(IRQ_GPIOE(21), detect_irq, IRQF_TRIGGER_RISING, + "sdhc1-card-detect", data); } -static int uart_mxc_port2_exit(struct platform_device *pdev) +static int mx27ads_sdhc2_init(struct device *dev, irq_handler_t detect_irq, + void *data) { - mxc_gpio_release_multiple_pins(mxc_uart2_pins, - ARRAY_SIZE(mxc_uart2_pins)); - return 0; + return request_irq(IRQ_GPIOB(7), detect_irq, IRQF_TRIGGER_RISING, + "sdhc2-card-detect", data); } -static int mxc_uart3_pins[] = { - PB26_AF_UART4_RTS, - PB28_AF_UART4_TXD, - PB29_AF_UART4_CTS, - PB31_AF_UART4_RXD -}; - -static int uart_mxc_port3_init(struct platform_device *pdev) +static void mx27ads_sdhc1_exit(struct device *dev, void *data) { - return mxc_gpio_setup_multiple_pins(mxc_uart3_pins, - ARRAY_SIZE(mxc_uart3_pins), "UART3"); + free_irq(IRQ_GPIOE(21), data); } -static int uart_mxc_port3_exit(struct platform_device *pdev) +static void mx27ads_sdhc2_exit(struct device *dev, void *data) { - mxc_gpio_release_multiple_pins(mxc_uart3_pins, - ARRAY_SIZE(mxc_uart3_pins)); - return 0; + free_irq(IRQ_GPIOB(7), data); } -static int mxc_uart4_pins[] = { - PB18_AF_UART5_TXD, - PB19_AF_UART5_RXD, - PB20_AF_UART5_CTS, - PB21_AF_UART5_RTS +static struct imxmmc_platform_data sdhc1_pdata = { + .init = mx27ads_sdhc1_init, + .exit = mx27ads_sdhc1_exit, }; -static int uart_mxc_port4_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_uart4_pins, - ARRAY_SIZE(mxc_uart4_pins), "UART4"); -} - -static int uart_mxc_port4_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart4_pins, - ARRAY_SIZE(mxc_uart4_pins)); - return 0; -} - -static int mxc_uart5_pins[] = { - PB10_AF_UART6_TXD, - PB12_AF_UART6_CTS, - PB11_AF_UART6_RXD, - PB13_AF_UART6_RTS +static struct imxmmc_platform_data sdhc2_pdata = { + .init = mx27ads_sdhc2_init, + .exit = mx27ads_sdhc2_exit, }; -static int uart_mxc_port5_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_uart5_pins, - ARRAY_SIZE(mxc_uart5_pins), "UART5"); -} - -static int uart_mxc_port5_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart5_pins, - ARRAY_SIZE(mxc_uart5_pins)); - return 0; -} - static struct platform_device *platform_devices[] __initdata = { &mx27ads_nor_mtd_device, &mxc_fec_device, + &mxc_w1_master_device, }; -static int mxc_fec_pins[] = { - PD0_AIN_FEC_TXD0, - PD1_AIN_FEC_TXD1, - PD2_AIN_FEC_TXD2, - PD3_AIN_FEC_TXD3, - PD4_AOUT_FEC_RX_ER, - PD5_AOUT_FEC_RXD1, - PD6_AOUT_FEC_RXD2, - PD7_AOUT_FEC_RXD3, - PD8_AF_FEC_MDIO, - PD9_AIN_FEC_MDC, - PD10_AOUT_FEC_CRS, - PD11_AOUT_FEC_TX_CLK, - PD12_AOUT_FEC_RXD0, - PD13_AOUT_FEC_RX_DV, - PD14_AOUT_FEC_RX_CLK, - PD15_AOUT_FEC_COL, - PD16_AIN_FEC_TX_ER, - PF23_AIN_FEC_TX_EN -}; - -static void gpio_fec_active(void) -{ - mxc_gpio_setup_multiple_pins(mxc_fec_pins, - ARRAY_SIZE(mxc_fec_pins), "FEC"); -} - static struct imxuart_platform_data uart_pdata[] = { { - .init = uart_mxc_port0_init, - .exit = uart_mxc_port0_exit, .flags = IMXUART_HAVE_RTSCTS, }, { - .init = uart_mxc_port1_init, - .exit = uart_mxc_port1_exit, .flags = IMXUART_HAVE_RTSCTS, }, { - .init = uart_mxc_port2_init, - .exit = uart_mxc_port2_exit, .flags = IMXUART_HAVE_RTSCTS, }, { - .init = uart_mxc_port3_init, - .exit = uart_mxc_port3_exit, .flags = IMXUART_HAVE_RTSCTS, }, { - .init = uart_mxc_port4_init, - .exit = uart_mxc_port4_exit, .flags = IMXUART_HAVE_RTSCTS, }, { - .init = uart_mxc_port5_init, - .exit = uart_mxc_port5_exit, .flags = IMXUART_HAVE_RTSCTS, }, }; static void __init mx27ads_board_init(void) { - gpio_fec_active(); + mxc_gpio_setup_multiple_pins(mx27ads_pins, ARRAY_SIZE(mx27ads_pins), + "mx27ads"); mxc_register_device(&mxc_uart_device0, &uart_pdata[0]); mxc_register_device(&mxc_uart_device1, &uart_pdata[1]); @@ -248,6 +282,15 @@ static void __init mx27ads_board_init(void) mxc_register_device(&mxc_uart_device3, &uart_pdata[3]); mxc_register_device(&mxc_uart_device4, &uart_pdata[4]); mxc_register_device(&mxc_uart_device5, &uart_pdata[5]); + mxc_register_device(&mxc_nand_device, &mx27ads_nand_board_info); + + /* only the i2c master 1 is used on this CPU card */ + i2c_register_board_info(1, mx27ads_i2c_devices, + ARRAY_SIZE(mx27ads_i2c_devices)); + mxc_register_device(&mxc_i2c_device1, &mx27ads_i2c_data); + mxc_register_device(&mxc_fb_device, &mx27ads_fb_data); + mxc_register_device(&mxc_sdhc_device0, &sdhc1_pdata); + mxc_register_device(&mxc_sdhc_device1, &sdhc2_pdata); platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); } @@ -277,7 +320,7 @@ static struct map_desc mx27ads_io_desc[] __initdata = { static void __init mx27ads_map_io(void) { - mxc_map_io(); + mx27_map_io(); iotable_init(mx27ads_io_desc, ARRAY_SIZE(mx27ads_io_desc)); } diff --git a/arch/arm/mach-mx2/mx27pdk.c b/arch/arm/mach-mx2/mx27pdk.c new file mode 100644 index 00000000000..90b1fa5d184 --- /dev/null +++ b/arch/arm/mach-mx2/mx27pdk.c @@ -0,0 +1,95 @@ +/* + * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved. + * + * Author: Fabio Estevam <fabio.estevam@freescale.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <mach/hardware.h> +#include <mach/common.h> +#include <mach/imx-uart.h> +#include <mach/iomux.h> +#include <mach/board-mx27pdk.h> + +#include "devices.h" + +static unsigned int mx27pdk_pins[] = { + /* UART1 */ + PE12_PF_UART1_TXD, + PE13_PF_UART1_RXD, + PE14_PF_UART1_CTS, + PE15_PF_UART1_RTS, + /* FEC */ + PD0_AIN_FEC_TXD0, + PD1_AIN_FEC_TXD1, + PD2_AIN_FEC_TXD2, + PD3_AIN_FEC_TXD3, + PD4_AOUT_FEC_RX_ER, + PD5_AOUT_FEC_RXD1, + PD6_AOUT_FEC_RXD2, + PD7_AOUT_FEC_RXD3, + PD8_AF_FEC_MDIO, + PD9_AIN_FEC_MDC, + PD10_AOUT_FEC_CRS, + PD11_AOUT_FEC_TX_CLK, + PD12_AOUT_FEC_RXD0, + PD13_AOUT_FEC_RX_DV, + PD14_AOUT_FEC_RX_CLK, + PD15_AOUT_FEC_COL, + PD16_AIN_FEC_TX_ER, + PF23_AIN_FEC_TX_EN, +}; + +static struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +static struct platform_device *platform_devices[] __initdata = { + &mxc_fec_device, +}; + +static void __init mx27pdk_init(void) +{ + mxc_gpio_setup_multiple_pins(mx27pdk_pins, ARRAY_SIZE(mx27pdk_pins), + "mx27pdk"); + mxc_register_device(&mxc_uart_device0, &uart_pdata); + platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); +} + +static void __init mx27pdk_timer_init(void) +{ + mx27_clocks_init(26000000); +} + +static struct sys_timer mx27pdk_timer = { + .init = mx27pdk_timer_init, +}; + +MACHINE_START(MX27_3DS, "Freescale MX27PDK") + /* maintainer: Freescale Semiconductor, Inc. */ + .phys_io = AIPI_BASE_ADDR, + .io_pg_offst = ((AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, + .boot_params = PHYS_OFFSET + 0x100, + .map_io = mxc_map_io, + .init_irq = mxc_init_irq, + .init_machine = mx27pdk_init, + .timer = &mx27pdk_timer, +MACHINE_END diff --git a/arch/arm/mach-mx2/pcm038.c b/arch/arm/mach-mx2/pcm038.c index aa4eaa61d1b..a4628d00434 100644 --- a/arch/arm/mach-mx2/pcm038.c +++ b/arch/arm/mach-mx2/pcm038.c @@ -17,28 +17,84 @@ * MA 02110-1301, USA. */ -#include <linux/platform_device.h> -#include <linux/mtd/physmap.h> -#include <linux/mtd/plat-ram.h> -#include <linux/io.h> #include <linux/i2c.h> #include <linux/i2c/at24.h> +#include <linux/io.h> +#include <linux/mtd/plat-ram.h> +#include <linux/mtd/physmap.h> +#include <linux/platform_device.h> -#include <asm/mach/arch.h> #include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> + +#include <mach/board-pcm038.h> #include <mach/common.h> #include <mach/hardware.h> -#include <mach/iomux.h> -#ifdef CONFIG_I2C_IMX #include <mach/i2c.h> -#endif -#include <asm/mach/time.h> +#include <mach/iomux.h> #include <mach/imx-uart.h> -#include <mach/board-pcm038.h> #include <mach/mxc_nand.h> #include "devices.h" +static int pcm038_pins[] = { + /* UART1 */ + PE12_PF_UART1_TXD, + PE13_PF_UART1_RXD, + PE14_PF_UART1_CTS, + PE15_PF_UART1_RTS, + /* UART2 */ + PE3_PF_UART2_CTS, + PE4_PF_UART2_RTS, + PE6_PF_UART2_TXD, + PE7_PF_UART2_RXD, + /* UART3 */ + PE8_PF_UART3_TXD, + PE9_PF_UART3_RXD, + PE10_PF_UART3_CTS, + PE11_PF_UART3_RTS, + /* FEC */ + PD0_AIN_FEC_TXD0, + PD1_AIN_FEC_TXD1, + PD2_AIN_FEC_TXD2, + PD3_AIN_FEC_TXD3, + PD4_AOUT_FEC_RX_ER, + PD5_AOUT_FEC_RXD1, + PD6_AOUT_FEC_RXD2, + PD7_AOUT_FEC_RXD3, + PD8_AF_FEC_MDIO, + PD9_AIN_FEC_MDC, + PD10_AOUT_FEC_CRS, + PD11_AOUT_FEC_TX_CLK, + PD12_AOUT_FEC_RXD0, + PD13_AOUT_FEC_RX_DV, + PD14_AOUT_FEC_RX_CLK, + PD15_AOUT_FEC_COL, + PD16_AIN_FEC_TX_ER, + PF23_AIN_FEC_TX_EN, + /* I2C2 */ + PC5_PF_I2C2_SDA, + PC6_PF_I2C2_SCL, + /* SPI1 */ + PD25_PF_CSPI1_RDY, + PD27_PF_CSPI1_SS1, + PD28_PF_CSPI1_SS0, + PD29_PF_CSPI1_SCLK, + PD30_PF_CSPI1_MISO, + PD31_PF_CSPI1_MOSI, + /* SSI1 */ + PC20_PF_SSI1_FS, + PC21_PF_SSI1_RXD, + PC22_PF_SSI1_TXD, + PC23_PF_SSI1_CLK, + /* SSI4 */ + PC16_PF_SSI4_FS, + PC17_PF_SSI4_RXD, + PC18_PF_SSI4_TXD, + PC19_PF_SSI4_CLK, +}; + /* * Phytec's PCM038 comes with 2MiB battery buffered SRAM, * 16 bit width @@ -88,107 +144,16 @@ static struct platform_device pcm038_nor_mtd_device = { .resource = &pcm038_flash_resource, }; -static int mxc_uart0_pins[] = { - PE12_PF_UART1_TXD, - PE13_PF_UART1_RXD, - PE14_PF_UART1_CTS, - PE15_PF_UART1_RTS -}; - -static int uart_mxc_port0_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_uart0_pins, - ARRAY_SIZE(mxc_uart0_pins), "UART0"); -} - -static int uart_mxc_port0_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart0_pins, - ARRAY_SIZE(mxc_uart0_pins)); - return 0; -} - -static int mxc_uart1_pins[] = { - PE3_PF_UART2_CTS, - PE4_PF_UART2_RTS, - PE6_PF_UART2_TXD, - PE7_PF_UART2_RXD -}; - -static int uart_mxc_port1_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_uart1_pins, - ARRAY_SIZE(mxc_uart1_pins), "UART1"); -} - -static int uart_mxc_port1_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart1_pins, - ARRAY_SIZE(mxc_uart1_pins)); - return 0; -} - -static int mxc_uart2_pins[] = { PE8_PF_UART3_TXD, - PE9_PF_UART3_RXD, - PE10_PF_UART3_CTS, - PE11_PF_UART3_RTS }; - -static int uart_mxc_port2_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_uart2_pins, - ARRAY_SIZE(mxc_uart2_pins), "UART2"); -} - -static int uart_mxc_port2_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_uart2_pins, - ARRAY_SIZE(mxc_uart2_pins)); - return 0; -} - static struct imxuart_platform_data uart_pdata[] = { { - .init = uart_mxc_port0_init, - .exit = uart_mxc_port0_exit, .flags = IMXUART_HAVE_RTSCTS, }, { - .init = uart_mxc_port1_init, - .exit = uart_mxc_port1_exit, .flags = IMXUART_HAVE_RTSCTS, }, { - .init = uart_mxc_port2_init, - .exit = uart_mxc_port2_exit, .flags = IMXUART_HAVE_RTSCTS, }, }; -static int mxc_fec_pins[] = { - PD0_AIN_FEC_TXD0, - PD1_AIN_FEC_TXD1, - PD2_AIN_FEC_TXD2, - PD3_AIN_FEC_TXD3, - PD4_AOUT_FEC_RX_ER, - PD5_AOUT_FEC_RXD1, - PD6_AOUT_FEC_RXD2, - PD7_AOUT_FEC_RXD3, - PD8_AF_FEC_MDIO, - PD9_AIN_FEC_MDC, - PD10_AOUT_FEC_CRS, - PD11_AOUT_FEC_TX_CLK, - PD12_AOUT_FEC_RXD0, - PD13_AOUT_FEC_RX_DV, - PD14_AOUT_FEC_RX_CLK, - PD15_AOUT_FEC_COL, - PD16_AIN_FEC_TX_ER, - PF23_AIN_FEC_TX_EN -}; - -static void gpio_fec_active(void) -{ - mxc_gpio_setup_multiple_pins(mxc_fec_pins, - ARRAY_SIZE(mxc_fec_pins), "FEC"); -} - static struct mxc_nand_platform_data pcm038_nand_board_info = { .width = 1, .hw_ecc = 1, @@ -210,27 +175,8 @@ static void __init pcm038_init_sram(void) __raw_writel(0x22220a00, CSCR_A(1)); } -#ifdef CONFIG_I2C_IMX -static int mxc_i2c1_pins[] = { - PC5_PF_I2C2_SDA, - PC6_PF_I2C2_SCL -}; - -static int pcm038_i2c_1_init(struct device *dev) -{ - return mxc_gpio_setup_multiple_pins(mxc_i2c1_pins, ARRAY_SIZE(mxc_i2c1_pins), - "I2C1"); -} - -static void pcm038_i2c_1_exit(struct device *dev) -{ - mxc_gpio_release_multiple_pins(mxc_i2c1_pins, ARRAY_SIZE(mxc_i2c1_pins)); -} - static struct imxi2c_platform_data pcm038_i2c_1_data = { .bitrate = 100000, - .init = pcm038_i2c_1_init, - .exit = pcm038_i2c_1_exit, }; static struct at24_platform_data board_eeprom = { @@ -253,11 +199,12 @@ static struct i2c_board_info pcm038_i2c_devices[] = { .type = "lm75" } }; -#endif static void __init pcm038_init(void) { - gpio_fec_active(); + mxc_gpio_setup_multiple_pins(pcm038_pins, ARRAY_SIZE(pcm038_pins), + "PCM038"); + pcm038_init_sram(); mxc_register_device(&mxc_uart_device0, &uart_pdata[0]); @@ -267,13 +214,11 @@ static void __init pcm038_init(void) mxc_gpio_mode(PE16_AF_OWIRE); mxc_register_device(&mxc_nand_device, &pcm038_nand_board_info); -#ifdef CONFIG_I2C_IMX /* only the i2c master 1 is used on this CPU card */ i2c_register_board_info(1, pcm038_i2c_devices, ARRAY_SIZE(pcm038_i2c_devices)); mxc_register_device(&mxc_i2c_device1, &pcm038_i2c_1_data); -#endif platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); @@ -295,7 +240,7 @@ MACHINE_START(PCM038, "phyCORE-i.MX27") .phys_io = AIPI_BASE_ADDR, .io_pg_offst = ((AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x100, - .map_io = mxc_map_io, + .map_io = mx27_map_io, .init_irq = mxc_init_irq, .init_machine = pcm038_init, .timer = &pcm038_timer, diff --git a/arch/arm/mach-mx2/pcm970-baseboard.c b/arch/arm/mach-mx2/pcm970-baseboard.c index bf4e520bc1b..6a3acaf57dd 100644 --- a/arch/arm/mach-mx2/pcm970-baseboard.c +++ b/arch/arm/mach-mx2/pcm970-baseboard.c @@ -16,71 +16,107 @@ * MA 02110-1301, USA. */ -#include <linux/platform_device.h> #include <linux/gpio.h> #include <linux/irq.h> +#include <linux/platform_device.h> #include <asm/mach/arch.h> -#include <mach/hardware.h> #include <mach/common.h> -#include <mach/mmc.h> -#include <mach/imxfb.h> #include <mach/iomux.h> +#include <mach/imxfb.h> +#include <mach/hardware.h> +#include <mach/mmc.h> #include "devices.h" -static int pcm970_sdhc2_get_ro(struct device *dev) -{ - return gpio_get_value(GPIO_PORTC + 28); -} - -static int pcm970_sdhc2_pins[] = { +static int pcm970_pins[] = { + /* SDHC */ PB4_PF_SD2_D0, PB5_PF_SD2_D1, PB6_PF_SD2_D2, PB7_PF_SD2_D3, PB8_PF_SD2_CMD, PB9_PF_SD2_CLK, + GPIO_PORTC | 28 | GPIO_GPIO | GPIO_IN, /* card detect */ + /* display */ + PA5_PF_LSCLK, + PA6_PF_LD0, + PA7_PF_LD1, + PA8_PF_LD2, + PA9_PF_LD3, + PA10_PF_LD4, + PA11_PF_LD5, + PA12_PF_LD6, + PA13_PF_LD7, + PA14_PF_LD8, + PA15_PF_LD9, + PA16_PF_LD10, + PA17_PF_LD11, + PA18_PF_LD12, + PA19_PF_LD13, + PA20_PF_LD14, + PA21_PF_LD15, + PA22_PF_LD16, + PA23_PF_LD17, + PA24_PF_REV, + PA25_PF_CLS, + PA26_PF_PS, + PA27_PF_SPL_SPR, + PA28_PF_HSYNC, + PA29_PF_VSYNC, + PA30_PF_CONTRAST, + PA31_PF_OE_ACD, + /* + * it seems the data line misses a pullup, so we must enable + * the internal pullup as a local workaround + */ + PD17_PF_I2C_DATA | GPIO_PUEN, + PD18_PF_I2C_CLK, + /* Camera */ + PB10_PF_CSI_D0, + PB11_PF_CSI_D1, + PB12_PF_CSI_D2, + PB13_PF_CSI_D3, + PB14_PF_CSI_D4, + PB15_PF_CSI_MCLK, + PB16_PF_CSI_PIXCLK, + PB17_PF_CSI_D5, + PB18_PF_CSI_D6, + PB19_PF_CSI_D7, + PB20_PF_CSI_VSYNC, + PB21_PF_CSI_HSYNC, }; +static int pcm970_sdhc2_get_ro(struct device *dev) +{ + return gpio_get_value(GPIO_PORTC + 28); +} + static int pcm970_sdhc2_init(struct device *dev, irq_handler_t detect_irq, void *data) { int ret; - ret = mxc_gpio_setup_multiple_pins(pcm970_sdhc2_pins, - ARRAY_SIZE(pcm970_sdhc2_pins), "sdhc2"); - if(ret) - return ret; - - ret = request_irq(IRQ_GPIOC(29), detect_irq, 0, + ret = request_irq(IRQ_GPIOC(29), detect_irq, IRQF_TRIGGER_FALLING, "imx-mmc-detect", data); if (ret) - goto out_release_gpio; - - set_irq_type(IRQ_GPIOC(29), IRQF_TRIGGER_FALLING); + return ret; ret = gpio_request(GPIO_PORTC + 28, "imx-mmc-ro"); - if (ret) - goto out_release_gpio; + if (ret) { + free_irq(IRQ_GPIOC(29), data); + return ret; + } - mxc_gpio_mode((GPIO_PORTC | 28) | GPIO_GPIO | GPIO_IN); gpio_direction_input(GPIO_PORTC + 28); return 0; - -out_release_gpio: - mxc_gpio_release_multiple_pins(pcm970_sdhc2_pins, - ARRAY_SIZE(pcm970_sdhc2_pins)); - return ret; } static void pcm970_sdhc2_exit(struct device *dev, void *data) { free_irq(IRQ_GPIOC(29), data); gpio_free(GPIO_PORTC + 28); - mxc_gpio_release_multiple_pins(pcm970_sdhc2_pins, - ARRAY_SIZE(pcm970_sdhc2_pins)); } static struct imxmmc_platform_data sdhc_pdata = { @@ -89,29 +125,6 @@ static struct imxmmc_platform_data sdhc_pdata = { .exit = pcm970_sdhc2_exit, }; -static int mxc_fb_pins[] = { - PA5_PF_LSCLK, PA6_PF_LD0, PA7_PF_LD1, PA8_PF_LD2, - PA9_PF_LD3, PA10_PF_LD4, PA11_PF_LD5, PA12_PF_LD6, - PA13_PF_LD7, PA14_PF_LD8, PA15_PF_LD9, PA16_PF_LD10, - PA17_PF_LD11, PA18_PF_LD12, PA19_PF_LD13, PA20_PF_LD14, - PA21_PF_LD15, PA22_PF_LD16, PA23_PF_LD17, PA24_PF_REV, - PA25_PF_CLS, PA26_PF_PS, PA27_PF_SPL_SPR, PA28_PF_HSYNC, - PA29_PF_VSYNC, PA30_PF_CONTRAST, PA31_PF_OE_ACD -}; - -static int pcm038_fb_init(struct platform_device *pdev) -{ - return mxc_gpio_setup_multiple_pins(mxc_fb_pins, - ARRAY_SIZE(mxc_fb_pins), "FB"); -} - -static int pcm038_fb_exit(struct platform_device *pdev) -{ - mxc_gpio_release_multiple_pins(mxc_fb_pins, ARRAY_SIZE(mxc_fb_pins)); - - return 0; -} - /* * Connected is a portrait Sharp-QVGA display * of type: LQ035Q7DH06 @@ -144,9 +157,6 @@ static struct imx_fb_platform_data pcm038_fb_data = { .pwmr = 0x00A903FF, .lscr1 = 0x00120300, .dmacr = 0x00020010, - - .init = pcm038_fb_init, - .exit = pcm038_fb_exit, }; /* @@ -157,6 +167,9 @@ static struct imx_fb_platform_data pcm038_fb_data = { */ void __init pcm970_baseboard_init(void) { + mxc_gpio_setup_multiple_pins(pcm970_pins, ARRAY_SIZE(pcm970_pins), + "PCM970"); + mxc_register_device(&mxc_fb_device, &pcm038_fb_data); mxc_register_device(&mxc_sdhc_device1, &sdhc_pdata); } diff --git a/arch/arm/mach-mx3/Kconfig b/arch/arm/mach-mx3/Kconfig index 194b8428bba..32e45155089 100644 --- a/arch/arm/mach-mx3/Kconfig +++ b/arch/arm/mach-mx3/Kconfig @@ -1,10 +1,12 @@ if ARCH_MX3 config ARCH_MX31 + select ARCH_HAS_RNGA bool config ARCH_MX35 bool + select ARCH_MXC_IOMUX_V3 comment "MX3 platforms:" @@ -66,4 +68,11 @@ config MACH_QONG Include support for Dave/DENX QongEVB-LITE platform. This includes specific configurations for the board and its peripherals. +config MACH_PCM043 + bool "Support Phytec pcm043 (i.MX35) platforms" + select ARCH_MX35 + help + Include support for Phytec pcm043 platform. This includes + specific configurations for the board and its peripherals. + endif diff --git a/arch/arm/mach-mx3/Makefile b/arch/arm/mach-mx3/Makefile index 272c8a953b3..cd6547b61b1 100644 --- a/arch/arm/mach-mx3/Makefile +++ b/arch/arm/mach-mx3/Makefile @@ -14,3 +14,4 @@ obj-$(CONFIG_MACH_MX31_3DS) += mx31pdk.o obj-$(CONFIG_MACH_MX31MOBOARD) += mx31moboard.o mx31moboard-devboard.o \ mx31moboard-marxbot.o obj-$(CONFIG_MACH_QONG) += qong.o +obj-$(CONFIG_MACH_PCM043) += pcm043.o diff --git a/arch/arm/mach-mx3/clock-imx35.c b/arch/arm/mach-mx3/clock-imx35.c index 53a112d4e04..0d76521cb49 100644 --- a/arch/arm/mach-mx3/clock-imx35.c +++ b/arch/arm/mach-mx3/clock-imx35.c @@ -147,34 +147,16 @@ static struct arm_ahb_div clk_consumer[] = { { .arm = 0, .ahb = 0, .sel = 0}, }; -static struct arm_ahb_div clk_automotive[] = { - { .arm = 1, .ahb = 3, .sel = 0}, - { .arm = 1, .ahb = 2, .sel = 1}, - { .arm = 2, .ahb = 1, .sel = 1}, - { .arm = 0, .ahb = 0, .sel = 0}, - { .arm = 1, .ahb = 6, .sel = 0}, - { .arm = 1, .ahb = 4, .sel = 1}, - { .arm = 2, .ahb = 2, .sel = 1}, - { .arm = 0, .ahb = 0, .sel = 0}, -}; - static unsigned long get_rate_arm(void) { unsigned long pdr0 = __raw_readl(CCM_BASE + CCM_PDR0); struct arm_ahb_div *aad; unsigned long fref = get_rate_mpll(); - if (pdr0 & 1) { - /* consumer path */ - aad = &clk_consumer[(pdr0 >> 16) & 0xf]; - if (aad->sel) - fref = fref * 2 / 3; - } else { - /* auto path */ - aad = &clk_automotive[(pdr0 >> 9) & 0x7]; - if (aad->sel) - fref = fref * 3 / 4; - } + aad = &clk_consumer[(pdr0 >> 16) & 0xf]; + if (aad->sel) + fref = fref * 2 / 3; + return fref / aad->arm; } @@ -184,12 +166,7 @@ static unsigned long get_rate_ahb(struct clk *clk) struct arm_ahb_div *aad; unsigned long fref = get_rate_mpll(); - if (pdr0 & 1) - /* consumer path */ - aad = &clk_consumer[(pdr0 >> 16) & 0xf]; - else - /* auto path */ - aad = &clk_automotive[(pdr0 >> 9) & 0x7]; + aad = &clk_consumer[(pdr0 >> 16) & 0xf]; return fref / aad->ahb; } @@ -430,7 +407,8 @@ static struct clk_lookup lookups[] __initdata = { _REGISTER_CLOCK("imx-i2c.1", NULL, i2c2_clk) _REGISTER_CLOCK("imx-i2c.2", NULL, i2c3_clk) _REGISTER_CLOCK(NULL, "iomuxc", iomuxc_clk) - _REGISTER_CLOCK(NULL, "ipu", ipu_clk) + _REGISTER_CLOCK("ipu-core", NULL, ipu_clk) + _REGISTER_CLOCK("mx3_sdc_fb", NULL, ipu_clk) _REGISTER_CLOCK(NULL, "kpp", kpp_clk) _REGISTER_CLOCK(NULL, "mlb", mlb_clk) _REGISTER_CLOCK(NULL, "mshc", mshc_clk) @@ -462,8 +440,6 @@ int __init mx35_clocks_init() int i; unsigned int ll = 0; - mxc_set_cpu_type(MXC_CPU_MX35); - #ifdef CONFIG_DEBUG_LL_CONSOLE ll = (3 << 16); #endif diff --git a/arch/arm/mach-mx3/clock.c b/arch/arm/mach-mx3/clock.c index 9957a11533a..28bd11dc89b 100644 --- a/arch/arm/mach-mx3/clock.c +++ b/arch/arm/mach-mx3/clock.c @@ -566,8 +566,6 @@ int __init mx31_clocks_init(unsigned long fref) u32 reg; int i; - mxc_set_cpu_type(MXC_CPU_MX31); - ckih_rate = fref; for (i = 0; i < ARRAY_SIZE(lookups); i++) @@ -581,6 +579,12 @@ int __init mx31_clocks_init(unsigned long fref) MX32, but still required to be set */ MXC_CCM_CGR2); + /* + * Before turning off usb_pll make sure ipg_per_clk is generated + * by ipg_clk and not usb_pll. + */ + __raw_writel(__raw_readl(MXC_CCM_CCMR) | (1 << 24), MXC_CCM_CCMR); + usb_pll_disable(&usb_pll_clk); pr_info("Clock input source is %ld\n", clk_get_rate(&ckih_clk)); diff --git a/arch/arm/mach-mx3/devices.c b/arch/arm/mach-mx3/devices.c index 380be0c9b21..d927eddcad4 100644 --- a/arch/arm/mach-mx3/devices.c +++ b/arch/arm/mach-mx3/devices.c @@ -17,13 +17,17 @@ * Boston, MA 02110-1301, USA. */ +#include <linux/dma-mapping.h> #include <linux/module.h> #include <linux/platform_device.h> #include <linux/serial.h> #include <linux/gpio.h> +#include <linux/dma-mapping.h> #include <mach/hardware.h> #include <mach/irqs.h> +#include <mach/common.h> #include <mach/imx-uart.h> +#include <mach/mx3_camera.h> #include "devices.h" @@ -283,6 +287,21 @@ struct platform_device mxcsdhc_device1 = { .num_resources = ARRAY_SIZE(mxcsdhc1_resources), .resource = mxcsdhc1_resources, }; + +static struct resource rnga_resources[] = { + { + .start = RNGA_BASE_ADDR, + .end = RNGA_BASE_ADDR + 0x28, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device mxc_rnga_device = { + .name = "mxc_rnga", + .id = -1, + .num_resources = 1, + .resource = rnga_resources, +}; #endif /* CONFIG_ARCH_MX31 */ /* i.MX31 Image Processing Unit */ @@ -329,10 +348,54 @@ struct platform_device mx3_fb = { .num_resources = ARRAY_SIZE(fb_resources), .resource = fb_resources, .dev = { - .coherent_dma_mask = 0xffffffff, + .coherent_dma_mask = DMA_BIT_MASK(32), }, }; +static struct resource camera_resources[] = { + { + .start = IPU_CTRL_BASE_ADDR + 0x60, + .end = IPU_CTRL_BASE_ADDR + 0x87, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device mx3_camera = { + .name = "mx3-camera", + .id = 0, + .num_resources = ARRAY_SIZE(camera_resources), + .resource = camera_resources, + .dev = { + .coherent_dma_mask = DMA_BIT_MASK(32), + }, +}; + +static struct resource otg_resources[] = { + { + .start = OTG_BASE_ADDR, + .end = OTG_BASE_ADDR + 0x1ff, + .flags = IORESOURCE_MEM, + }, { + .start = MXC_INT_USB3, + .end = MXC_INT_USB3, + .flags = IORESOURCE_IRQ, + }, +}; + +static u64 otg_dmamask = DMA_BIT_MASK(32); + +/* OTG gadget device */ +struct platform_device mxc_otg_udc_device = { + .name = "fsl-usb2-udc", + .id = -1, + .dev = { + .dma_mask = &otg_dmamask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, + .resource = otg_resources, + .num_resources = ARRAY_SIZE(otg_resources), +}; + #ifdef CONFIG_ARCH_MX35 static struct resource mxc_fec_resources[] = { { @@ -359,6 +422,7 @@ static int mx3_devices_init(void) if (cpu_is_mx31()) { mxc_nand_resources[0].start = MX31_NFC_BASE_ADDR; mxc_nand_resources[0].end = MX31_NFC_BASE_ADDR + 0xfff; + mxc_register_device(&mxc_rnga_device, NULL); } if (cpu_is_mx35()) { mxc_nand_resources[0].start = MX35_NFC_BASE_ADDR; diff --git a/arch/arm/mach-mx3/devices.h b/arch/arm/mach-mx3/devices.h index 88c04b296fa..475410ada60 100644 --- a/arch/arm/mach-mx3/devices.h +++ b/arch/arm/mach-mx3/devices.h @@ -11,6 +11,8 @@ extern struct platform_device mxc_i2c_device1; extern struct platform_device mxc_i2c_device2; extern struct platform_device mx3_ipu; extern struct platform_device mx3_fb; +extern struct platform_device mx3_camera; extern struct platform_device mxc_fec_device; extern struct platform_device mxcsdhc_device0; extern struct platform_device mxcsdhc_device1; +extern struct platform_device mxc_otg_udc_device; diff --git a/arch/arm/mach-mx3/iomux.c b/arch/arm/mach-mx3/iomux.c index 40ffc5a664d..c66ccbcdc11 100644 --- a/arch/arm/mach-mx3/iomux.c +++ b/arch/arm/mach-mx3/iomux.c @@ -21,7 +21,6 @@ #include <linux/module.h> #include <linux/spinlock.h> #include <linux/io.h> -#include <linux/gpio.h> #include <linux/kernel.h> #include <mach/hardware.h> #include <mach/gpio.h> @@ -94,15 +93,13 @@ void mxc_iomux_set_pad(enum iomux_pins pin, u32 config) EXPORT_SYMBOL(mxc_iomux_set_pad); /* - * setups a single pin: + * allocs a single pin: * - reserves the pin so that it is not claimed by another driver * - setups the iomux according to the configuration - * - if the pin is configured as a GPIO, we claim it through kernel gpiolib */ -int mxc_iomux_setup_pin(const unsigned int pin, const char *label) +int mxc_iomux_alloc_pin(const unsigned int pin, const char *label) { unsigned pad = pin & IOMUX_PADNUM_MASK; - unsigned gpio; if (pad >= (PIN_MAX + 1)) { printk(KERN_ERR "mxc_iomux: Attempt to request nonexistant pin %u for \"%s\"\n", @@ -113,19 +110,13 @@ int mxc_iomux_setup_pin(const unsigned int pin, const char *label) if (test_and_set_bit(pad, mxc_pin_alloc_map)) { printk(KERN_ERR "mxc_iomux: pin %u already used. Allocation for \"%s\" failed\n", pad, label ? label : "?"); - return -EINVAL; + return -EBUSY; } mxc_iomux_mode(pin); - /* if we have a gpio, we can allocate it */ - gpio = (pin & IOMUX_GPIONUM_MASK) >> IOMUX_GPIONUM_SHIFT; - if (gpio < (GPIO_PORT_MAX + 1) * 32) - if (gpio_request(gpio, label)) - return -EINVAL; - return 0; } -EXPORT_SYMBOL(mxc_iomux_setup_pin); +EXPORT_SYMBOL(mxc_iomux_alloc_pin); int mxc_iomux_setup_multiple_pins(unsigned int *pin_list, unsigned count, const char *label) @@ -135,7 +126,8 @@ int mxc_iomux_setup_multiple_pins(unsigned int *pin_list, unsigned count, int ret = -EINVAL; for (i = 0; i < count; i++) { - if (mxc_iomux_setup_pin(*p, label)) + ret = mxc_iomux_alloc_pin(*p, label); + if (ret) goto setup_error; p++; } @@ -150,14 +142,9 @@ EXPORT_SYMBOL(mxc_iomux_setup_multiple_pins); void mxc_iomux_release_pin(const unsigned int pin) { unsigned pad = pin & IOMUX_PADNUM_MASK; - unsigned gpio; if (pad < (PIN_MAX + 1)) clear_bit(pad, mxc_pin_alloc_map); - - gpio = (pin & IOMUX_GPIONUM_MASK) >> IOMUX_GPIONUM_SHIFT; - if (gpio < (GPIO_PORT_MAX + 1) * 32) - gpio_free(gpio); } EXPORT_SYMBOL(mxc_iomux_release_pin); diff --git a/arch/arm/mach-mx3/mm.c b/arch/arm/mach-mx3/mm.c index 9e1459cb4b7..1f5fdd456cb 100644 --- a/arch/arm/mach-mx3/mm.c +++ b/arch/arm/mach-mx3/mm.c @@ -72,8 +72,17 @@ static struct map_desc mxc_io_desc[] __initdata = { * system startup to create static physical to virtual memory mappings * for the IO modules. */ -void __init mxc_map_io(void) +void __init mx31_map_io(void) { + mxc_set_cpu_type(MXC_CPU_MX31); + + iotable_init(mxc_io_desc, ARRAY_SIZE(mxc_io_desc)); +} + +void __init mx35_map_io(void) +{ + mxc_set_cpu_type(MXC_CPU_MX35); + iotable_init(mxc_io_desc, ARRAY_SIZE(mxc_io_desc)); } diff --git a/arch/arm/mach-mx3/mx31ads.c b/arch/arm/mach-mx3/mx31ads.c index a6d6efefa6a..30e2767a78a 100644 --- a/arch/arm/mach-mx3/mx31ads.c +++ b/arch/arm/mach-mx3/mx31ads.c @@ -187,7 +187,7 @@ static void __init mx31ads_init_expio(void) /* * Configure INT line as GPIO input */ - mxc_iomux_setup_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio"); + mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio"); /* disable the interrupt and clear the status */ __raw_writew(0xFFFF, PBC_INTMASK_CLEAR_REG); @@ -511,7 +511,7 @@ static struct map_desc mx31ads_io_desc[] __initdata = { */ static void __init mx31ads_map_io(void) { - mxc_map_io(); + mx31_map_io(); iotable_init(mx31ads_io_desc, ARRAY_SIZE(mx31ads_io_desc)); } diff --git a/arch/arm/mach-mx3/mx31lite.c b/arch/arm/mach-mx3/mx31lite.c index 894d98cd994..86fe70fa3e1 100644 --- a/arch/arm/mach-mx3/mx31lite.c +++ b/arch/arm/mach-mx3/mx31lite.c @@ -22,6 +22,9 @@ #include <linux/init.h> #include <linux/kernel.h> #include <linux/memory.h> +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <linux/smsc911x.h> #include <mach/hardware.h> #include <asm/mach-types.h> @@ -32,11 +35,64 @@ #include <asm/page.h> #include <asm/setup.h> #include <mach/board-mx31lite.h> +#include <mach/imx-uart.h> +#include <mach/iomux-mx3.h> +#include <mach/irqs.h> +#include <mach/mxc_nand.h> +#include "devices.h" /* * This file contains the board-specific initialization routines. */ +static unsigned int mx31lite_pins[] = { + /* UART1 */ + MX31_PIN_CTS1__CTS1, + MX31_PIN_RTS1__RTS1, + MX31_PIN_TXD1__TXD1, + MX31_PIN_RXD1__RXD1, + /* LAN9117 IRQ pin */ + IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO), +}; + +static struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +static struct mxc_nand_platform_data mx31lite_nand_board_info = { + .width = 1, + .hw_ecc = 1, +}; + +static struct smsc911x_platform_config smsc911x_config = { + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL, + .flags = SMSC911X_USE_16BIT, +}; + +static struct resource smsc911x_resources[] = { + [0] = { + .start = CS4_BASE_ADDR, + .end = CS4_BASE_ADDR + 0x100, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IOMUX_TO_IRQ(MX31_PIN_SFS6), + .end = IOMUX_TO_IRQ(MX31_PIN_SFS6), + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device smsc911x_device = { + .name = "smsc911x", + .id = -1, + .num_resources = ARRAY_SIZE(smsc911x_resources), + .resource = smsc911x_resources, + .dev = { + .platform_data = &smsc911x_config, + }, +}; + /* * This structure defines the MX31 memory map. */ @@ -59,7 +115,7 @@ static struct map_desc mx31lite_io_desc[] __initdata = { */ void __init mx31lite_map_io(void) { - mxc_map_io(); + mx31_map_io(); iotable_init(mx31lite_io_desc, ARRAY_SIZE(mx31lite_io_desc)); } @@ -68,6 +124,22 @@ void __init mx31lite_map_io(void) */ static void __init mxc_board_init(void) { + int ret; + + mxc_iomux_setup_multiple_pins(mx31lite_pins, ARRAY_SIZE(mx31lite_pins), + "mx31lite"); + + mxc_register_device(&mxc_uart_device0, &uart_pdata); + mxc_register_device(&mxc_nand_device, &mx31lite_nand_board_info); + + /* SMSC9117 IRQ pin */ + ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_SFS6), "sms9117-irq"); + if (ret) + pr_warning("could not get LAN irq gpio\n"); + else { + gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_SFS6)); + platform_device_register(&smsc911x_device); + } } static void __init mx31lite_timer_init(void) diff --git a/arch/arm/mach-mx3/mx31moboard-devboard.c b/arch/arm/mach-mx3/mx31moboard-devboard.c index d080b4add79..4704405165a 100644 --- a/arch/arm/mach-mx3/mx31moboard-devboard.c +++ b/arch/arm/mach-mx3/mx31moboard-devboard.c @@ -16,33 +16,142 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#include <linux/types.h> +#include <linux/fsl_devices.h> +#include <linux/gpio.h> #include <linux/init.h> - +#include <linux/interrupt.h> #include <linux/platform_device.h> +#include <linux/types.h> -#include <mach/hardware.h> #include <mach/common.h> #include <mach/imx-uart.h> #include <mach/iomux-mx3.h> +#include <mach/hardware.h> +#include <mach/mmc.h> #include "devices.h" +static unsigned int devboard_pins[] = { + /* UART1 */ + MX31_PIN_CTS2__CTS2, MX31_PIN_RTS2__RTS2, + MX31_PIN_TXD2__TXD2, MX31_PIN_RXD2__RXD2, + /* SDHC2 */ + MX31_PIN_PC_PWRON__SD2_DATA3, MX31_PIN_PC_VS1__SD2_DATA2, + MX31_PIN_PC_READY__SD2_DATA1, MX31_PIN_PC_WAIT_B__SD2_DATA0, + MX31_PIN_PC_CD2_B__SD2_CLK, MX31_PIN_PC_CD1_B__SD2_CMD, + MX31_PIN_ATA_DIOR__GPIO3_28, MX31_PIN_ATA_DIOW__GPIO3_29, + /* USB OTG */ + MX31_PIN_USBOTG_DATA0__USBOTG_DATA0, + MX31_PIN_USBOTG_DATA1__USBOTG_DATA1, + MX31_PIN_USBOTG_DATA2__USBOTG_DATA2, + MX31_PIN_USBOTG_DATA3__USBOTG_DATA3, + MX31_PIN_USBOTG_DATA4__USBOTG_DATA4, + MX31_PIN_USBOTG_DATA5__USBOTG_DATA5, + MX31_PIN_USBOTG_DATA6__USBOTG_DATA6, + MX31_PIN_USBOTG_DATA7__USBOTG_DATA7, + MX31_PIN_USBOTG_CLK__USBOTG_CLK, MX31_PIN_USBOTG_DIR__USBOTG_DIR, + MX31_PIN_USBOTG_NXT__USBOTG_NXT, MX31_PIN_USBOTG_STP__USBOTG_STP, + MX31_PIN_USB_OC__GPIO1_30, +}; + static struct imxuart_platform_data uart_pdata = { .flags = IMXUART_HAVE_RTSCTS, }; -static int mxc_uart1_pins[] = { - MX31_PIN_CTS2__CTS2, MX31_PIN_RTS2__RTS2, - MX31_PIN_TXD2__TXD2, MX31_PIN_RXD2__RXD2, +#define SDHC2_CD IOMUX_TO_GPIO(MX31_PIN_ATA_DIOR) +#define SDHC2_WP IOMUX_TO_GPIO(MX31_PIN_ATA_DIOW) + +static int devboard_sdhc2_get_ro(struct device *dev) +{ + return gpio_get_value(SDHC2_WP); +} + +static int devboard_sdhc2_init(struct device *dev, irq_handler_t detect_irq, + void *data) +{ + int ret; + + ret = gpio_request(SDHC2_CD, "sdhc-detect"); + if (ret) + return ret; + + gpio_direction_input(SDHC2_CD); + + ret = gpio_request(SDHC2_WP, "sdhc-wp"); + if (ret) + goto err_gpio_free; + gpio_direction_input(SDHC2_WP); + + ret = request_irq(gpio_to_irq(SDHC2_CD), detect_irq, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + "sdhc2-card-detect", data); + if (ret) + goto err_gpio_free_2; + + return 0; + +err_gpio_free_2: + gpio_free(SDHC2_WP); +err_gpio_free: + gpio_free(SDHC2_CD); + + return ret; +} + +static void devboard_sdhc2_exit(struct device *dev, void *data) +{ + free_irq(gpio_to_irq(SDHC2_CD), data); + gpio_free(SDHC2_WP); + gpio_free(SDHC2_CD); +} + +static struct imxmmc_platform_data sdhc2_pdata = { + .get_ro = devboard_sdhc2_get_ro, + .init = devboard_sdhc2_init, + .exit = devboard_sdhc2_exit, +}; + +static struct fsl_usb2_platform_data usb_pdata = { + .operating_mode = FSL_USB2_DR_DEVICE, + .phy_mode = FSL_USB2_PHY_ULPI, }; +#define OTG_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST) +#define OTG_EN_B IOMUX_TO_GPIO(MX31_PIN_USB_OC) + +static void devboard_usbotg_init(void) +{ + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, OTG_PAD_CFG); + + gpio_request(OTG_EN_B, "usb-udc-en"); + gpio_direction_output(OTG_EN_B, 0); +} + /* * system init for baseboard usage. Will be called by mx31moboard init. */ void __init mx31moboard_devboard_init(void) { printk(KERN_INFO "Initializing mx31devboard peripherals\n"); - mxc_iomux_setup_multiple_pins(mxc_uart1_pins, ARRAY_SIZE(mxc_uart1_pins), "uart1"); + + mxc_iomux_setup_multiple_pins(devboard_pins, ARRAY_SIZE(devboard_pins), + "devboard"); + mxc_register_device(&mxc_uart_device1, &uart_pdata); + + mxc_register_device(&mxcsdhc_device1, &sdhc2_pdata); + + devboard_usbotg_init(); + mxc_register_device(&mxc_otg_udc_device, &usb_pdata); } diff --git a/arch/arm/mach-mx3/mx31moboard-marxbot.c b/arch/arm/mach-mx3/mx31moboard-marxbot.c index 9ef9566823f..641c3d6153a 100644 --- a/arch/arm/mach-mx3/mx31moboard-marxbot.c +++ b/arch/arm/mach-mx3/mx31moboard-marxbot.c @@ -16,22 +16,144 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#include <linux/types.h> +#include <linux/fsl_devices.h> +#include <linux/gpio.h> #include <linux/init.h> - +#include <linux/interrupt.h> #include <linux/platform_device.h> +#include <linux/types.h> -#include <mach/hardware.h> #include <mach/common.h> +#include <mach/hardware.h> #include <mach/imx-uart.h> #include <mach/iomux-mx3.h> +#include <mach/mmc.h> #include "devices.h" +static unsigned int marxbot_pins[] = { + /* SDHC2 */ + MX31_PIN_PC_PWRON__SD2_DATA3, MX31_PIN_PC_VS1__SD2_DATA2, + MX31_PIN_PC_READY__SD2_DATA1, MX31_PIN_PC_WAIT_B__SD2_DATA0, + MX31_PIN_PC_CD2_B__SD2_CLK, MX31_PIN_PC_CD1_B__SD2_CMD, + MX31_PIN_ATA_DIOR__GPIO3_28, MX31_PIN_ATA_DIOW__GPIO3_29, + /* CSI */ + MX31_PIN_CSI_D4__CSI_D4, MX31_PIN_CSI_D5__CSI_D5, + MX31_PIN_CSI_D6__CSI_D6, MX31_PIN_CSI_D7__CSI_D7, + MX31_PIN_CSI_D8__CSI_D8, MX31_PIN_CSI_D9__CSI_D9, + MX31_PIN_CSI_D10__CSI_D10, MX31_PIN_CSI_D11__CSI_D11, + MX31_PIN_CSI_D12__CSI_D12, MX31_PIN_CSI_D13__CSI_D13, + MX31_PIN_CSI_D14__CSI_D14, MX31_PIN_CSI_D15__CSI_D15, + MX31_PIN_CSI_HSYNC__CSI_HSYNC, MX31_PIN_CSI_MCLK__CSI_MCLK, + MX31_PIN_CSI_PIXCLK__CSI_PIXCLK, MX31_PIN_CSI_VSYNC__CSI_VSYNC, + MX31_PIN_GPIO3_0__GPIO3_0, MX31_PIN_GPIO3_1__GPIO3_1, + MX31_PIN_TXD2__GPIO1_28, + /* USB OTG */ + MX31_PIN_USBOTG_DATA0__USBOTG_DATA0, + MX31_PIN_USBOTG_DATA1__USBOTG_DATA1, + MX31_PIN_USBOTG_DATA2__USBOTG_DATA2, + MX31_PIN_USBOTG_DATA3__USBOTG_DATA3, + MX31_PIN_USBOTG_DATA4__USBOTG_DATA4, + MX31_PIN_USBOTG_DATA5__USBOTG_DATA5, + MX31_PIN_USBOTG_DATA6__USBOTG_DATA6, + MX31_PIN_USBOTG_DATA7__USBOTG_DATA7, + MX31_PIN_USBOTG_CLK__USBOTG_CLK, MX31_PIN_USBOTG_DIR__USBOTG_DIR, + MX31_PIN_USBOTG_NXT__USBOTG_NXT, MX31_PIN_USBOTG_STP__USBOTG_STP, + MX31_PIN_USB_OC__GPIO1_30, +}; + +#define SDHC2_CD IOMUX_TO_GPIO(MX31_PIN_ATA_DIOR) +#define SDHC2_WP IOMUX_TO_GPIO(MX31_PIN_ATA_DIOW) + +static int marxbot_sdhc2_get_ro(struct device *dev) +{ + return gpio_get_value(SDHC2_WP); +} + +static int marxbot_sdhc2_init(struct device *dev, irq_handler_t detect_irq, + void *data) +{ + int ret; + + ret = gpio_request(SDHC2_CD, "sdhc-detect"); + if (ret) + return ret; + + gpio_direction_input(SDHC2_CD); + + ret = gpio_request(SDHC2_WP, "sdhc-wp"); + if (ret) + goto err_gpio_free; + gpio_direction_input(SDHC2_WP); + + ret = request_irq(gpio_to_irq(SDHC2_CD), detect_irq, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + "sdhc2-card-detect", data); + if (ret) + goto err_gpio_free_2; + + return 0; + +err_gpio_free_2: + gpio_free(SDHC2_WP); +err_gpio_free: + gpio_free(SDHC2_CD); + + return ret; +} + +static void marxbot_sdhc2_exit(struct device *dev, void *data) +{ + free_irq(gpio_to_irq(SDHC2_CD), data); + gpio_free(SDHC2_WP); + gpio_free(SDHC2_CD); +} + +static struct imxmmc_platform_data sdhc2_pdata = { + .get_ro = marxbot_sdhc2_get_ro, + .init = marxbot_sdhc2_init, + .exit = marxbot_sdhc2_exit, +}; + +static struct fsl_usb2_platform_data usb_pdata = { + .operating_mode = FSL_USB2_DR_DEVICE, + .phy_mode = FSL_USB2_PHY_ULPI, +}; + +#define OTG_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST) +#define OTG_EN_B IOMUX_TO_GPIO(MX31_PIN_USB_OC) + +static void marxbot_usbotg_init(void) +{ + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, OTG_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, OTG_PAD_CFG); + + gpio_request(OTG_EN_B, "usb-udc-en"); + gpio_direction_output(OTG_EN_B, 0); +} + /* * system init for baseboard usage. Will be called by mx31moboard init. */ void __init mx31moboard_marxbot_init(void) { printk(KERN_INFO "Initializing mx31marxbot peripherals\n"); + + mxc_iomux_setup_multiple_pins(marxbot_pins, ARRAY_SIZE(marxbot_pins), + "marxbot"); + + mxc_register_device(&mxcsdhc_device1, &sdhc2_pdata); + + marxbot_usbotg_init(); + mxc_register_device(&mxc_otg_udc_device, &usb_pdata); } diff --git a/arch/arm/mach-mx3/mx31moboard.c b/arch/arm/mach-mx3/mx31moboard.c index 34c2a1b99d4..a17f2e41160 100644 --- a/arch/arm/mach-mx3/mx31moboard.c +++ b/arch/arm/mach-mx3/mx31moboard.c @@ -16,26 +16,47 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> - -#include <linux/platform_device.h> +#include <linux/interrupt.h> +#include <linux/memory.h> #include <linux/mtd/physmap.h> #include <linux/mtd/partitions.h> -#include <linux/memory.h> +#include <linux/platform_device.h> +#include <linux/types.h> -#include <mach/hardware.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <asm/mach/time.h> #include <asm/mach/map.h> +#include <mach/board-mx31moboard.h> #include <mach/common.h> +#include <mach/hardware.h> #include <mach/imx-uart.h> #include <mach/iomux-mx3.h> -#include <mach/board-mx31moboard.h> +#include <mach/i2c.h> +#include <mach/mmc.h> #include "devices.h" +static unsigned int moboard_pins[] = { + /* UART0 */ + MX31_PIN_CTS1__CTS1, MX31_PIN_RTS1__RTS1, + MX31_PIN_TXD1__TXD1, MX31_PIN_RXD1__RXD1, + /* UART4 */ + MX31_PIN_PC_RST__CTS5, MX31_PIN_PC_VS2__RTS5, + MX31_PIN_PC_BVD2__TXD5, MX31_PIN_PC_BVD1__RXD5, + /* I2C0 */ + MX31_PIN_I2C_DAT__I2C1_SDA, MX31_PIN_I2C_CLK__I2C1_SCL, + /* I2C1 */ + MX31_PIN_DCD_DTE1__I2C2_SDA, MX31_PIN_RI_DTE1__I2C2_SCL, + /* SDHC1 */ + MX31_PIN_SD1_DATA3__SD1_DATA3, MX31_PIN_SD1_DATA2__SD1_DATA2, + MX31_PIN_SD1_DATA1__SD1_DATA1, MX31_PIN_SD1_DATA0__SD1_DATA0, + MX31_PIN_SD1_CLK__SD1_CLK, MX31_PIN_SD1_CMD__SD1_CMD, + MX31_PIN_ATA_CS0__GPIO3_26, MX31_PIN_ATA_CS1__GPIO3_27, +}; + static struct physmap_flash_data mx31moboard_flash_data = { .width = 2, }; @@ -60,17 +81,69 @@ static struct imxuart_platform_data uart_pdata = { .flags = IMXUART_HAVE_RTSCTS, }; -static struct platform_device *devices[] __initdata = { - &mx31moboard_flash, +static struct imxi2c_platform_data moboard_i2c0_pdata = { + .bitrate = 400000, }; -static int mxc_uart0_pins[] = { - MX31_PIN_CTS1__CTS1, MX31_PIN_RTS1__RTS1, - MX31_PIN_TXD1__TXD1, MX31_PIN_RXD1__RXD1, +static struct imxi2c_platform_data moboard_i2c1_pdata = { + .bitrate = 100000, }; -static int mxc_uart4_pins[] = { - MX31_PIN_PC_RST__CTS5, MX31_PIN_PC_VS2__RTS5, - MX31_PIN_PC_BVD2__TXD5, MX31_PIN_PC_BVD1__RXD5, + +#define SDHC1_CD IOMUX_TO_GPIO(MX31_PIN_ATA_CS0) +#define SDHC1_WP IOMUX_TO_GPIO(MX31_PIN_ATA_CS1) + +static int moboard_sdhc1_get_ro(struct device *dev) +{ + return gpio_get_value(SDHC1_WP); +} + +static int moboard_sdhc1_init(struct device *dev, irq_handler_t detect_irq, + void *data) +{ + int ret; + + ret = gpio_request(SDHC1_CD, "sdhc-detect"); + if (ret) + return ret; + + gpio_direction_input(SDHC1_CD); + + ret = gpio_request(SDHC1_WP, "sdhc-wp"); + if (ret) + goto err_gpio_free; + gpio_direction_input(SDHC1_WP); + + ret = request_irq(gpio_to_irq(SDHC1_CD), detect_irq, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + "sdhc1-card-detect", data); + if (ret) + goto err_gpio_free_2; + + return 0; + +err_gpio_free_2: + gpio_free(SDHC1_WP); +err_gpio_free: + gpio_free(SDHC1_CD); + + return ret; +} + +static void moboard_sdhc1_exit(struct device *dev, void *data) +{ + free_irq(gpio_to_irq(SDHC1_CD), data); + gpio_free(SDHC1_WP); + gpio_free(SDHC1_CD); +} + +static struct imxmmc_platform_data sdhc1_pdata = { + .get_ro = moboard_sdhc1_get_ro, + .init = moboard_sdhc1_init, + .exit = moboard_sdhc1_exit, +}; + +static struct platform_device *devices[] __initdata = { + &mx31moboard_flash, }; static int mx31moboard_baseboard; @@ -81,14 +154,19 @@ core_param(mx31moboard_baseboard, mx31moboard_baseboard, int, 0444); */ static void __init mxc_board_init(void) { + mxc_iomux_setup_multiple_pins(moboard_pins, ARRAY_SIZE(moboard_pins), + "moboard"); + platform_add_devices(devices, ARRAY_SIZE(devices)); - mxc_iomux_setup_multiple_pins(mxc_uart0_pins, ARRAY_SIZE(mxc_uart0_pins), "uart0"); mxc_register_device(&mxc_uart_device0, &uart_pdata); - - mxc_iomux_setup_multiple_pins(mxc_uart4_pins, ARRAY_SIZE(mxc_uart4_pins), "uart4"); mxc_register_device(&mxc_uart_device4, &uart_pdata); + mxc_register_device(&mxc_i2c_device0, &moboard_i2c0_pdata); + mxc_register_device(&mxc_i2c_device1, &moboard_i2c1_pdata); + + mxc_register_device(&mxcsdhc_device0, &sdhc1_pdata); + switch (mx31moboard_baseboard) { case MX31NOBOARD: break; @@ -99,7 +177,8 @@ static void __init mxc_board_init(void) mx31moboard_marxbot_init(); break; default: - printk(KERN_ERR "Illegal mx31moboard_baseboard type %d\n", mx31moboard_baseboard); + printk(KERN_ERR "Illegal mx31moboard_baseboard type %d\n", + mx31moboard_baseboard); } } @@ -117,7 +196,7 @@ MACHINE_START(MX31MOBOARD, "EPFL Mobots mx31moboard") .phys_io = AIPS1_BASE_ADDR, .io_pg_offst = ((AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x100, - .map_io = mxc_map_io, + .map_io = mx31_map_io, .init_irq = mxc_init_irq, .init_machine = mxc_board_init, .timer = &mx31moboard_timer, diff --git a/arch/arm/mach-mx3/mx31pdk.c b/arch/arm/mach-mx3/mx31pdk.c index bc63f178569..32599e50753 100644 --- a/arch/arm/mach-mx3/mx31pdk.c +++ b/arch/arm/mach-mx3/mx31pdk.c @@ -20,6 +20,7 @@ #include <linux/init.h> #include <linux/clk.h> #include <linux/irq.h> +#include <linux/gpio.h> #include <mach/hardware.h> #include <asm/mach-types.h> @@ -41,21 +42,159 @@ * @ingroup System */ +static int mx31pdk_pins[] = { + /* UART1 */ + MX31_PIN_CTS1__CTS1, + MX31_PIN_RTS1__RTS1, + MX31_PIN_TXD1__TXD1, + MX31_PIN_RXD1__RXD1, + IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO), +}; + static struct imxuart_platform_data uart_pdata = { .flags = IMXUART_HAVE_RTSCTS, }; -static int uart_pins[] = { - MX31_PIN_CTS1__CTS1, - MX31_PIN_RTS1__RTS1, - MX31_PIN_TXD1__TXD1, - MX31_PIN_RXD1__RXD1 +/* + * Routines for the CPLD on the debug board. It contains a CPLD handling + * LEDs, switches, interrupts for Ethernet. + */ + +static void mx31pdk_expio_irq_handler(uint32_t irq, struct irq_desc *desc) +{ + uint32_t imr_val; + uint32_t int_valid; + uint32_t expio_irq; + + imr_val = __raw_readw(CPLD_INT_MASK_REG); + int_valid = __raw_readw(CPLD_INT_STATUS_REG) & ~imr_val; + + expio_irq = MXC_EXP_IO_BASE; + for (; int_valid != 0; int_valid >>= 1, expio_irq++) { + if ((int_valid & 1) == 0) + continue; + generic_handle_irq(expio_irq); + } +} + +/* + * Disable an expio pin's interrupt by setting the bit in the imr. + * @param irq an expio virtual irq number + */ +static void expio_mask_irq(uint32_t irq) +{ + uint16_t reg; + uint32_t expio = MXC_IRQ_TO_EXPIO(irq); + + /* mask the interrupt */ + reg = __raw_readw(CPLD_INT_MASK_REG); + reg |= 1 << expio; + __raw_writew(reg, CPLD_INT_MASK_REG); +} + +/* + * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr. + * @param irq an expanded io virtual irq number + */ +static void expio_ack_irq(uint32_t irq) +{ + uint32_t expio = MXC_IRQ_TO_EXPIO(irq); + + /* clear the interrupt status */ + __raw_writew(1 << expio, CPLD_INT_RESET_REG); + __raw_writew(0, CPLD_INT_RESET_REG); + /* mask the interrupt */ + expio_mask_irq(irq); +} + +/* + * Enable a expio pin's interrupt by clearing the bit in the imr. + * @param irq a expio virtual irq number + */ +static void expio_unmask_irq(uint32_t irq) +{ + uint16_t reg; + uint32_t expio = MXC_IRQ_TO_EXPIO(irq); + + /* unmask the interrupt */ + reg = __raw_readw(CPLD_INT_MASK_REG); + reg &= ~(1 << expio); + __raw_writew(reg, CPLD_INT_MASK_REG); +} + +static struct irq_chip expio_irq_chip = { + .ack = expio_ack_irq, + .mask = expio_mask_irq, + .unmask = expio_unmask_irq, }; -static inline void mxc_init_imx_uart(void) +static int __init mx31pdk_init_expio(void) { - mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins), "uart-0"); - mxc_register_device(&mxc_uart_device0, &uart_pdata); + int i; + int ret; + + /* Check if there's a debug board connected */ + if ((__raw_readw(CPLD_MAGIC_NUMBER1_REG) != 0xAAAA) || + (__raw_readw(CPLD_MAGIC_NUMBER2_REG) != 0x5555) || + (__raw_readw(CPLD_MAGIC_NUMBER3_REG) != 0xCAFE)) { + /* No Debug board found */ + return -ENODEV; + } + + pr_info("i.MX31PDK Debug board detected, rev = 0x%04X\n", + __raw_readw(CPLD_CODE_VER_REG)); + + /* + * Configure INT line as GPIO input + */ + ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "sms9217-irq"); + if (ret) + pr_warning("could not get LAN irq gpio\n"); + else + gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)); + + /* Disable the interrupts and clear the status */ + __raw_writew(0, CPLD_INT_MASK_REG); + __raw_writew(0xFFFF, CPLD_INT_RESET_REG); + __raw_writew(0, CPLD_INT_RESET_REG); + __raw_writew(0x1F, CPLD_INT_MASK_REG); + for (i = MXC_EXP_IO_BASE; + i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES); + i++) { + set_irq_chip(i, &expio_irq_chip); + set_irq_handler(i, handle_level_irq); + set_irq_flags(i, IRQF_VALID); + } + set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_LOW); + set_irq_chained_handler(EXPIO_PARENT_INT, mx31pdk_expio_irq_handler); + + return 0; +} + +/* + * This structure defines the MX31 memory map. + */ +static struct map_desc mx31pdk_io_desc[] __initdata = { + { + .virtual = SPBA0_BASE_ADDR_VIRT, + .pfn = __phys_to_pfn(SPBA0_BASE_ADDR), + .length = SPBA0_SIZE, + .type = MT_DEVICE_NONSHARED, + }, { + .virtual = CS5_BASE_ADDR_VIRT, + .pfn = __phys_to_pfn(CS5_BASE_ADDR), + .length = CS5_SIZE, + .type = MT_DEVICE, + }, +}; + +/* + * Set up static virtual mappings. + */ +static void __init mx31pdk_map_io(void) +{ + mx31_map_io(); + iotable_init(mx31pdk_io_desc, ARRAY_SIZE(mx31pdk_io_desc)); } /*! @@ -63,7 +202,12 @@ static inline void mxc_init_imx_uart(void) */ static void __init mxc_board_init(void) { - mxc_init_imx_uart(); + mxc_iomux_setup_multiple_pins(mx31pdk_pins, ARRAY_SIZE(mx31pdk_pins), + "mx31pdk"); + + mxc_register_device(&mxc_uart_device0, &uart_pdata); + + mx31pdk_init_expio(); } static void __init mx31pdk_timer_init(void) @@ -84,7 +228,7 @@ MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)") .phys_io = AIPS1_BASE_ADDR, .io_pg_offst = ((AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x100, - .map_io = mxc_map_io, + .map_io = mx31pdk_map_io, .init_irq = mxc_init_irq, .init_machine = mxc_board_init, .timer = &mx31pdk_timer, diff --git a/arch/arm/mach-mx3/pcm037.c b/arch/arm/mach-mx3/pcm037.c index b5227d837b2..c6f61a1f06c 100644 --- a/arch/arm/mach-mx3/pcm037.c +++ b/arch/arm/mach-mx3/pcm037.c @@ -28,6 +28,10 @@ #include <linux/interrupt.h> #include <linux/i2c.h> #include <linux/i2c/at24.h> +#include <linux/delay.h> +#include <linux/spi/spi.h> +#include <linux/irq.h> +#include <linux/fsl_devices.h> #include <mach/hardware.h> #include <asm/mach-types.h> @@ -37,7 +41,9 @@ #include <mach/common.h> #include <mach/imx-uart.h> #include <mach/iomux-mx3.h> +#include <mach/ipu.h> #include <mach/board-pcm037.h> +#include <mach/mx3fb.h> #include <mach/mxc_nand.h> #include <mach/mmc.h> #ifdef CONFIG_I2C_IMX @@ -46,6 +52,76 @@ #include "devices.h" +static unsigned int pcm037_pins[] = { + /* I2C */ + MX31_PIN_CSPI2_MOSI__SCL, + MX31_PIN_CSPI2_MISO__SDA, + /* SDHC1 */ + MX31_PIN_SD1_DATA3__SD1_DATA3, + MX31_PIN_SD1_DATA2__SD1_DATA2, + MX31_PIN_SD1_DATA1__SD1_DATA1, + MX31_PIN_SD1_DATA0__SD1_DATA0, + MX31_PIN_SD1_CLK__SD1_CLK, + MX31_PIN_SD1_CMD__SD1_CMD, + IOMUX_MODE(MX31_PIN_SCK6, IOMUX_CONFIG_GPIO), /* card detect */ + IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO), /* write protect */ + /* SPI1 */ + MX31_PIN_CSPI1_MOSI__MOSI, + MX31_PIN_CSPI1_MISO__MISO, + MX31_PIN_CSPI1_SCLK__SCLK, + MX31_PIN_CSPI1_SPI_RDY__SPI_RDY, + MX31_PIN_CSPI1_SS0__SS0, + MX31_PIN_CSPI1_SS1__SS1, + MX31_PIN_CSPI1_SS2__SS2, + /* UART1 */ + MX31_PIN_CTS1__CTS1, + MX31_PIN_RTS1__RTS1, + MX31_PIN_TXD1__TXD1, + MX31_PIN_RXD1__RXD1, + /* UART2 */ + MX31_PIN_TXD2__TXD2, + MX31_PIN_RXD2__RXD2, + MX31_PIN_CTS2__CTS2, + MX31_PIN_RTS2__RTS2, + /* UART3 */ + MX31_PIN_CSPI3_MOSI__RXD3, + MX31_PIN_CSPI3_MISO__TXD3, + MX31_PIN_CSPI3_SCLK__RTS3, + MX31_PIN_CSPI3_SPI_RDY__CTS3, + /* LAN9217 irq pin */ + IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO), + /* Onewire */ + MX31_PIN_BATT_LINE__OWIRE, + /* Framebuffer */ + MX31_PIN_LD0__LD0, + MX31_PIN_LD1__LD1, + MX31_PIN_LD2__LD2, + MX31_PIN_LD3__LD3, + MX31_PIN_LD4__LD4, + MX31_PIN_LD5__LD5, + MX31_PIN_LD6__LD6, + MX31_PIN_LD7__LD7, + MX31_PIN_LD8__LD8, + MX31_PIN_LD9__LD9, + MX31_PIN_LD10__LD10, + MX31_PIN_LD11__LD11, + MX31_PIN_LD12__LD12, + MX31_PIN_LD13__LD13, + MX31_PIN_LD14__LD14, + MX31_PIN_LD15__LD15, + MX31_PIN_LD16__LD16, + MX31_PIN_LD17__LD17, + MX31_PIN_VSYNC3__VSYNC3, + MX31_PIN_HSYNC__HSYNC, + MX31_PIN_FPSHIFT__FPSHIFT, + MX31_PIN_DRDY0__DRDY0, + MX31_PIN_D3_REV__D3_REV, + MX31_PIN_CONTRAST__CONTRAST, + MX31_PIN_D3_SPL__D3_SPL, + MX31_PIN_D3_CLS__D3_CLS, + MX31_PIN_LCS0__GPI03_23, +}; + static struct physmap_flash_data pcm037_flash_data = { .width = 2, }; @@ -56,6 +132,54 @@ static struct resource pcm037_flash_resource = { .flags = IORESOURCE_MEM, }; +static int usbotg_pins[] = { + MX31_PIN_USBOTG_DATA0__USBOTG_DATA0, + MX31_PIN_USBOTG_DATA1__USBOTG_DATA1, + MX31_PIN_USBOTG_DATA2__USBOTG_DATA2, + MX31_PIN_USBOTG_DATA3__USBOTG_DATA3, + MX31_PIN_USBOTG_DATA4__USBOTG_DATA4, + MX31_PIN_USBOTG_DATA5__USBOTG_DATA5, + MX31_PIN_USBOTG_DATA6__USBOTG_DATA6, + MX31_PIN_USBOTG_DATA7__USBOTG_DATA7, + MX31_PIN_USBOTG_CLK__USBOTG_CLK, + MX31_PIN_USBOTG_DIR__USBOTG_DIR, + MX31_PIN_USBOTG_NXT__USBOTG_NXT, + MX31_PIN_USBOTG_STP__USBOTG_STP, +}; + +/* USB OTG HS port */ +static int __init gpio_usbotg_hs_activate(void) +{ + int ret = mxc_iomux_setup_multiple_pins(usbotg_pins, + ARRAY_SIZE(usbotg_pins), "usbotg"); + + if (ret < 0) { + printk(KERN_ERR "Cannot set up OTG pins\n"); + return ret; + } + + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + + return 0; +} + +/* OTG config */ +static struct fsl_usb2_platform_data usb_pdata = { + .operating_mode = FSL_USB2_DR_DEVICE, + .phy_mode = FSL_USB2_PHY_ULPI, +}; + static struct platform_device pcm037_flash = { .name = "physmap-flash", .id = 0, @@ -127,26 +251,8 @@ static struct mxc_nand_platform_data pcm037_nand_board_info = { }; #ifdef CONFIG_I2C_IMX -static int i2c_1_pins[] = { - MX31_PIN_CSPI2_MOSI__SCL, - MX31_PIN_CSPI2_MISO__SDA, -}; - -static int pcm037_i2c_1_init(struct device *dev) -{ - return mxc_iomux_setup_multiple_pins(i2c_1_pins, ARRAY_SIZE(i2c_1_pins), - "i2c-1"); -} - -static void pcm037_i2c_1_exit(struct device *dev) -{ - mxc_iomux_release_multiple_pins(i2c_1_pins, ARRAY_SIZE(i2c_1_pins)); -} - static struct imxi2c_platform_data pcm037_i2c_1_data = { .bitrate = 100000, - .init = pcm037_i2c_1_init, - .exit = pcm037_i2c_1_exit, }; static struct at24_platform_data board_eeprom = { @@ -166,48 +272,119 @@ static struct i2c_board_info pcm037_i2c_devices[] = { }; #endif -static int sdhc1_pins[] = { - MX31_PIN_SD1_DATA3__SD1_DATA3, - MX31_PIN_SD1_DATA2__SD1_DATA2, - MX31_PIN_SD1_DATA1__SD1_DATA1, - MX31_PIN_SD1_DATA0__SD1_DATA0, - MX31_PIN_SD1_CLK__SD1_CLK, - MX31_PIN_SD1_CMD__SD1_CMD, -}; +/* Not connected by default */ +#ifdef PCM970_SDHC_RW_SWITCH +static int pcm970_sdhc1_get_ro(struct device *dev) +{ + return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_SFS6)); +} +#endif + +#define SDHC1_GPIO_WP IOMUX_TO_GPIO(MX31_PIN_SFS6) +#define SDHC1_GPIO_DET IOMUX_TO_GPIO(MX31_PIN_SCK6) -static int pcm970_sdhc1_init(struct device *dev, irq_handler_t h, void *data) +static int pcm970_sdhc1_init(struct device *dev, irq_handler_t detect_irq, + void *data) { - return mxc_iomux_setup_multiple_pins(sdhc1_pins, ARRAY_SIZE(sdhc1_pins), - "sdhc-1"); + int ret; + + ret = gpio_request(SDHC1_GPIO_DET, "sdhc-detect"); + if (ret) + return ret; + + gpio_direction_input(SDHC1_GPIO_DET); + +#ifdef PCM970_SDHC_RW_SWITCH + ret = gpio_request(SDHC1_GPIO_WP, "sdhc-wp"); + if (ret) + goto err_gpio_free; + gpio_direction_input(SDHC1_GPIO_WP); +#endif + + ret = request_irq(IOMUX_TO_IRQ(MX31_PIN_SCK6), detect_irq, + IRQF_DISABLED | IRQF_TRIGGER_FALLING, + "sdhc-detect", data); + if (ret) + goto err_gpio_free_2; + + return 0; + +err_gpio_free_2: +#ifdef PCM970_SDHC_RW_SWITCH + gpio_free(SDHC1_GPIO_WP); +err_gpio_free: +#endif + gpio_free(SDHC1_GPIO_DET); + + return ret; } static void pcm970_sdhc1_exit(struct device *dev, void *data) { - mxc_iomux_release_multiple_pins(sdhc1_pins, ARRAY_SIZE(sdhc1_pins)); + free_irq(IOMUX_TO_IRQ(MX31_PIN_SCK6), data); + gpio_free(SDHC1_GPIO_DET); + gpio_free(SDHC1_GPIO_WP); } -/* No card and rw detection at the moment */ static struct imxmmc_platform_data sdhc_pdata = { +#ifdef PCM970_SDHC_RW_SWITCH + .get_ro = pcm970_sdhc1_get_ro, +#endif .init = pcm970_sdhc1_init, .exit = pcm970_sdhc1_exit, }; static struct platform_device *devices[] __initdata = { &pcm037_flash, - &pcm037_eth, &pcm037_sram_device, }; -static int uart0_pins[] = { - MX31_PIN_CTS1__CTS1, - MX31_PIN_RTS1__RTS1, - MX31_PIN_TXD1__TXD1, - MX31_PIN_RXD1__RXD1 +static struct ipu_platform_data mx3_ipu_data = { + .irq_base = MXC_IPU_IRQ_START, }; -static int uart2_pins[] = { - MX31_PIN_CSPI3_MOSI__RXD3, - MX31_PIN_CSPI3_MISO__TXD3 +static const struct fb_videomode fb_modedb[] = { + { + /* 240x320 @ 60 Hz Sharp */ + .name = "Sharp-LQ035Q7DH06-QVGA", + .refresh = 60, + .xres = 240, + .yres = 320, + .pixclock = 185925, + .left_margin = 9, + .right_margin = 16, + .upper_margin = 7, + .lower_margin = 9, + .hsync_len = 1, + .vsync_len = 1, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE | + FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN, + .vmode = FB_VMODE_NONINTERLACED, + .flag = 0, + }, { + /* 240x320 @ 60 Hz */ + .name = "TX090", + .refresh = 60, + .xres = 240, + .yres = 320, + .pixclock = 38255, + .left_margin = 144, + .right_margin = 0, + .upper_margin = 7, + .lower_margin = 40, + .hsync_len = 96, + .vsync_len = 1, + .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH, + .vmode = FB_VMODE_NONINTERLACED, + .flag = 0, + }, +}; + +static struct mx3fb_platform_data mx3fb_pdata = { + .dma_dev = &mx3_ipu.dev, + .name = "Sharp-LQ035Q7DH06-QVGA", + .mode = fb_modedb, + .num_modes = ARRAY_SIZE(fb_modedb), }; /* @@ -215,21 +392,28 @@ static int uart2_pins[] = { */ static void __init mxc_board_init(void) { + int ret; + + mxc_iomux_setup_multiple_pins(pcm037_pins, ARRAY_SIZE(pcm037_pins), + "pcm037"); + platform_add_devices(devices, ARRAY_SIZE(devices)); - mxc_iomux_setup_multiple_pins(uart0_pins, ARRAY_SIZE(uart0_pins), "uart-0"); mxc_register_device(&mxc_uart_device0, &uart_pdata); - - mxc_iomux_setup_multiple_pins(uart2_pins, ARRAY_SIZE(uart2_pins), "uart-2"); + mxc_register_device(&mxc_uart_device1, &uart_pdata); mxc_register_device(&mxc_uart_device2, &uart_pdata); - mxc_iomux_setup_pin(MX31_PIN_BATT_LINE__OWIRE, "batt-0wire"); mxc_register_device(&mxc_w1_master_device, NULL); /* LAN9217 IRQ pin */ - if (!mxc_iomux_setup_pin(IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO), - "pcm037-eth")) + ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1), "lan9217-irq"); + if (ret) + pr_warning("could not get LAN irq gpio\n"); + else { gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)); + platform_device_register(&pcm037_eth); + } + #ifdef CONFIG_I2C_IMX i2c_register_board_info(1, pcm037_i2c_devices, @@ -239,6 +423,10 @@ static void __init mxc_board_init(void) #endif mxc_register_device(&mxc_nand_device, &pcm037_nand_board_info); mxc_register_device(&mxcsdhc_device0, &sdhc_pdata); + mxc_register_device(&mx3_ipu, &mx3_ipu_data); + mxc_register_device(&mx3_fb, &mx3fb_pdata); + if (!gpio_usbotg_hs_activate()) + mxc_register_device(&mxc_otg_udc_device, &usb_pdata); } static void __init pcm037_timer_init(void) @@ -255,7 +443,7 @@ MACHINE_START(PCM037, "Phytec Phycore pcm037") .phys_io = AIPS1_BASE_ADDR, .io_pg_offst = ((AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x100, - .map_io = mxc_map_io, + .map_io = mx31_map_io, .init_irq = mxc_init_irq, .init_machine = mxc_board_init, .timer = &pcm037_timer, diff --git a/arch/arm/mach-mx3/pcm043.c b/arch/arm/mach-mx3/pcm043.c new file mode 100644 index 00000000000..8d27c324abf --- /dev/null +++ b/arch/arm/mach-mx3/pcm043.c @@ -0,0 +1,252 @@ +/* + * Copyright (C) 2009 Sascha Hauer, Pengutronix + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> + +#include <linux/platform_device.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/plat-ram.h> +#include <linux/memory.h> +#include <linux/gpio.h> +#include <linux/smc911x.h> +#include <linux/interrupt.h> +#include <linux/i2c.h> +#include <linux/i2c/at24.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <asm/mach/map.h> + +#include <mach/hardware.h> +#include <mach/common.h> +#include <mach/imx-uart.h> +#if defined CONFIG_I2C_IMX || defined CONFIG_I2C_IMX_MODULE +#include <mach/i2c.h> +#endif +#include <mach/iomux-mx35.h> +#include <mach/ipu.h> +#include <mach/mx3fb.h> + +#include "devices.h" + +static const struct fb_videomode fb_modedb[] = { + { + /* 240x320 @ 60 Hz */ + .name = "Sharp-LQ035Q7", + .refresh = 60, + .xres = 240, + .yres = 320, + .pixclock = 185925, + .left_margin = 9, + .right_margin = 16, + .upper_margin = 7, + .lower_margin = 9, + .hsync_len = 1, + .vsync_len = 1, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE | FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN, + .vmode = FB_VMODE_NONINTERLACED, + .flag = 0, + }, { + /* 240x320 @ 60 Hz */ + .name = "TX090", + .refresh = 60, + .xres = 240, + .yres = 320, + .pixclock = 38255, + .left_margin = 144, + .right_margin = 0, + .upper_margin = 7, + .lower_margin = 40, + .hsync_len = 96, + .vsync_len = 1, + .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH, + .vmode = FB_VMODE_NONINTERLACED, + .flag = 0, + }, +}; + +static struct ipu_platform_data mx3_ipu_data = { + .irq_base = MXC_IPU_IRQ_START, +}; + +static struct mx3fb_platform_data mx3fb_pdata = { + .dma_dev = &mx3_ipu.dev, + .name = "Sharp-LQ035Q7", + .mode = fb_modedb, + .num_modes = ARRAY_SIZE(fb_modedb), +}; + +static struct physmap_flash_data pcm043_flash_data = { + .width = 2, +}; + +static struct resource pcm043_flash_resource = { + .start = 0xa0000000, + .end = 0xa1ffffff, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device pcm043_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &pcm043_flash_data, + }, + .resource = &pcm043_flash_resource, + .num_resources = 1, +}; + +static struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +#if defined CONFIG_I2C_IMX || defined CONFIG_I2C_IMX_MODULE +static struct imxi2c_platform_data pcm043_i2c_1_data = { + .bitrate = 50000, +}; + +static struct at24_platform_data board_eeprom = { + .byte_len = 4096, + .page_size = 32, + .flags = AT24_FLAG_ADDR16, +}; + +static struct i2c_board_info pcm043_i2c_devices[] = { + { + I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */ + .platform_data = &board_eeprom, + }, { + I2C_BOARD_INFO("rtc-pcf8563", 0x51), + .type = "pcf8563", + } +}; +#endif + +static struct platform_device *devices[] __initdata = { + &pcm043_flash, + &mxc_fec_device, +}; + +static struct pad_desc pcm043_pads[] = { + /* UART1 */ + MX35_PAD_CTS1__UART1_CTS, + MX35_PAD_RTS1__UART1_RTS, + MX35_PAD_TXD1__UART1_TXD_MUX, + MX35_PAD_RXD1__UART1_RXD_MUX, + /* UART2 */ + MX35_PAD_CTS2__UART2_CTS, + MX35_PAD_RTS2__UART2_RTS, + MX35_PAD_TXD2__UART2_TXD_MUX, + MX35_PAD_RXD2__UART2_RXD_MUX, + /* FEC */ + MX35_PAD_FEC_TX_CLK__FEC_TX_CLK, + MX35_PAD_FEC_RX_CLK__FEC_RX_CLK, + MX35_PAD_FEC_RX_DV__FEC_RX_DV, + MX35_PAD_FEC_COL__FEC_COL, + MX35_PAD_FEC_RDATA0__FEC_RDATA_0, + MX35_PAD_FEC_TDATA0__FEC_TDATA_0, + MX35_PAD_FEC_TX_EN__FEC_TX_EN, + MX35_PAD_FEC_MDC__FEC_MDC, + MX35_PAD_FEC_MDIO__FEC_MDIO, + MX35_PAD_FEC_TX_ERR__FEC_TX_ERR, + MX35_PAD_FEC_RX_ERR__FEC_RX_ERR, + MX35_PAD_FEC_CRS__FEC_CRS, + MX35_PAD_FEC_RDATA1__FEC_RDATA_1, + MX35_PAD_FEC_TDATA1__FEC_TDATA_1, + MX35_PAD_FEC_RDATA2__FEC_RDATA_2, + MX35_PAD_FEC_TDATA2__FEC_TDATA_2, + MX35_PAD_FEC_RDATA3__FEC_RDATA_3, + MX35_PAD_FEC_TDATA3__FEC_TDATA_3, + /* I2C1 */ + MX35_PAD_I2C1_CLK__I2C1_SCL, + MX35_PAD_I2C1_DAT__I2C1_SDA, + /* Display */ + MX35_PAD_LD0__IPU_DISPB_DAT_0, + MX35_PAD_LD1__IPU_DISPB_DAT_1, + MX35_PAD_LD2__IPU_DISPB_DAT_2, + MX35_PAD_LD3__IPU_DISPB_DAT_3, + MX35_PAD_LD4__IPU_DISPB_DAT_4, + MX35_PAD_LD5__IPU_DISPB_DAT_5, + MX35_PAD_LD6__IPU_DISPB_DAT_6, + MX35_PAD_LD7__IPU_DISPB_DAT_7, + MX35_PAD_LD8__IPU_DISPB_DAT_8, + MX35_PAD_LD9__IPU_DISPB_DAT_9, + MX35_PAD_LD10__IPU_DISPB_DAT_10, + MX35_PAD_LD11__IPU_DISPB_DAT_11, + MX35_PAD_LD12__IPU_DISPB_DAT_12, + MX35_PAD_LD13__IPU_DISPB_DAT_13, + MX35_PAD_LD14__IPU_DISPB_DAT_14, + MX35_PAD_LD15__IPU_DISPB_DAT_15, + MX35_PAD_LD16__IPU_DISPB_DAT_16, + MX35_PAD_LD17__IPU_DISPB_DAT_17, + MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC, + MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK, + MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY, + MX35_PAD_CONTRAST__IPU_DISPB_CONTR, + MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC, + MX35_PAD_D3_REV__IPU_DISPB_D3_REV, + MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS, + MX35_PAD_D3_SPL__IPU_DISPB_D3_SPL +}; + +/* + * Board specific initialization. + */ +static void __init mxc_board_init(void) +{ + mxc_iomux_v3_setup_multiple_pads(pcm043_pads, ARRAY_SIZE(pcm043_pads)); + + platform_add_devices(devices, ARRAY_SIZE(devices)); + + mxc_register_device(&mxc_uart_device0, &uart_pdata); + + mxc_register_device(&mxc_uart_device1, &uart_pdata); + +#if defined CONFIG_I2C_IMX || defined CONFIG_I2C_IMX_MODULE + i2c_register_board_info(0, pcm043_i2c_devices, + ARRAY_SIZE(pcm043_i2c_devices)); + + mxc_register_device(&mxc_i2c_device0, &pcm043_i2c_1_data); +#endif + + mxc_register_device(&mx3_ipu, &mx3_ipu_data); + mxc_register_device(&mx3_fb, &mx3fb_pdata); +} + +static void __init pcm043_timer_init(void) +{ + mx35_clocks_init(); +} + +struct sys_timer pcm043_timer = { + .init = pcm043_timer_init, +}; + +MACHINE_START(PCM043, "Phytec Phycore pcm043") + /* Maintainer: Pengutronix */ + .phys_io = AIPS1_BASE_ADDR, + .io_pg_offst = ((AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc, + .boot_params = PHYS_OFFSET + 0x100, + .map_io = mx35_map_io, + .init_irq = mxc_init_irq, + .init_machine = mxc_board_init, + .timer = &pcm043_timer, +MACHINE_END + diff --git a/arch/arm/mach-mx3/qong.c b/arch/arm/mach-mx3/qong.c index 5a01e48fd8f..82b31c4ab11 100644 --- a/arch/arm/mach-mx3/qong.c +++ b/arch/arm/mach-mx3/qong.c @@ -279,7 +279,7 @@ MACHINE_START(QONG, "Dave/DENX QongEVB-LITE") .phys_io = AIPS1_BASE_ADDR, .io_pg_offst = ((AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x100, - .map_io = mxc_map_io, + .map_io = mx31_map_io, .init_irq = mxc_init_irq, .init_machine = mxc_board_init, .timer = &qong_timer, diff --git a/arch/arm/mach-omap1/board-h2-mmc.c b/arch/arm/mach-omap1/board-h2-mmc.c index 44d4a966bed..46098f54682 100644 --- a/arch/arm/mach-omap1/board-h2-mmc.c +++ b/arch/arm/mach-omap1/board-h2-mmc.c @@ -26,19 +26,13 @@ static int mmc_set_power(struct device *dev, int slot, int power_on, int vdd) { - if (power_on) - gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 1); - else - gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 0); - + gpio_set_value(H2_TPS_GPIO_MMC_PWR_EN, power_on); return 0; } static int mmc_late_init(struct device *dev) { - int ret; - - ret = gpio_request(H2_TPS_GPIO_MMC_PWR_EN, "MMC power"); + int ret = gpio_request(H2_TPS_GPIO_MMC_PWR_EN, "MMC power"); if (ret < 0) return ret; @@ -47,7 +41,7 @@ static int mmc_late_init(struct device *dev) return ret; } -static void mmc_shutdown(struct device *dev) +static void mmc_cleanup(struct device *dev) { gpio_free(H2_TPS_GPIO_MMC_PWR_EN); } @@ -60,7 +54,7 @@ static void mmc_shutdown(struct device *dev) static struct omap_mmc_platform_data mmc1_data = { .nr_slots = 1, .init = mmc_late_init, - .shutdown = mmc_shutdown, + .cleanup = mmc_cleanup, .dma_mask = 0xffffffff, .slots[0] = { .set_power = mmc_set_power, diff --git a/arch/arm/mach-omap1/board-h3-mmc.c b/arch/arm/mach-omap1/board-h3-mmc.c index 0d8a3c195e2..5e8877ce35e 100644 --- a/arch/arm/mach-omap1/board-h3-mmc.c +++ b/arch/arm/mach-omap1/board-h3-mmc.c @@ -26,11 +26,7 @@ static int mmc_set_power(struct device *dev, int slot, int power_on, int vdd) { - if (power_on) - gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 1); - else - gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 0); - + gpio_set_value(H3_TPS_GPIO_MMC_PWR_EN, power_on); return 0; } diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c index 4695965114c..f597968733b 100644 --- a/arch/arm/mach-omap1/board-h3.c +++ b/arch/arm/mach-omap1/board-h3.c @@ -39,12 +39,10 @@ #include <asm/mach/flash.h> #include <asm/mach/map.h> -#include <mach/gpioexpander.h> #include <mach/irqs.h> #include <mach/mux.h> #include <mach/tc.h> #include <mach/nand.h> -#include <mach/irda.h> #include <mach/usb.h> #include <mach/keypad.h> #include <mach/dma.h> @@ -276,104 +274,6 @@ static struct platform_device h3_kp_device = { .resource = h3_kp_resources, }; - -/* Select between the IrDA and aGPS module - */ -static int h3_select_irda(struct device *dev, int state) -{ - unsigned char expa; - int err = 0; - - if ((err = read_gpio_expa(&expa, 0x26))) { - printk(KERN_ERR "Error reading from I/O EXPANDER \n"); - return err; - } - - /* 'P6' enable/disable IRDA_TX and IRDA_RX */ - if (state & IR_SEL) { /* IrDA */ - if ((err = write_gpio_expa(expa | 0x40, 0x26))) { - printk(KERN_ERR "Error writing to I/O EXPANDER \n"); - return err; - } - } else { - if ((err = write_gpio_expa(expa & ~0x40, 0x26))) { - printk(KERN_ERR "Error writing to I/O EXPANDER \n"); - return err; - } - } - return err; -} - -static void set_trans_mode(struct work_struct *work) -{ - struct omap_irda_config *irda_config = - container_of(work, struct omap_irda_config, gpio_expa.work); - int mode = irda_config->mode; - unsigned char expa; - int err = 0; - - if ((err = read_gpio_expa(&expa, 0x27)) != 0) { - printk(KERN_ERR "Error reading from I/O expander\n"); - } - - expa &= ~0x03; - - if (mode & IR_SIRMODE) { - expa |= 0x01; - } else { /* MIR/FIR */ - expa |= 0x03; - } - - if ((err = write_gpio_expa(expa, 0x27)) != 0) { - printk(KERN_ERR "Error writing to I/O expander\n"); - } -} - -static int h3_transceiver_mode(struct device *dev, int mode) -{ - struct omap_irda_config *irda_config = dev->platform_data; - - irda_config->mode = mode; - cancel_delayed_work(&irda_config->gpio_expa); - PREPARE_DELAYED_WORK(&irda_config->gpio_expa, set_trans_mode); - schedule_delayed_work(&irda_config->gpio_expa, 0); - - return 0; -} - -static struct omap_irda_config h3_irda_data = { - .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE, - .transceiver_mode = h3_transceiver_mode, - .select_irda = h3_select_irda, - .rx_channel = OMAP_DMA_UART3_RX, - .tx_channel = OMAP_DMA_UART3_TX, - .dest_start = UART3_THR, - .src_start = UART3_RHR, - .tx_trigger = 0, - .rx_trigger = 0, -}; - -static struct resource h3_irda_resources[] = { - [0] = { - .start = INT_UART3, - .end = INT_UART3, - .flags = IORESOURCE_IRQ, - }, -}; - -static u64 irda_dmamask = 0xffffffff; - -static struct platform_device h3_irda_device = { - .name = "omapirda", - .id = 0, - .dev = { - .platform_data = &h3_irda_data, - .dma_mask = &irda_dmamask, - }, - .num_resources = ARRAY_SIZE(h3_irda_resources), - .resource = h3_irda_resources, -}; - static struct platform_device h3_lcd_device = { .name = "lcd_h3", .id = -1, @@ -395,7 +295,6 @@ static struct platform_device *devices[] __initdata = { &nand_device, &smc91x_device, &intlat_device, - &h3_irda_device, &h3_kp_device, &h3_lcd_device, }; diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c index 7bc7a3cb9c5..d1ed1365319 100644 --- a/arch/arm/mach-omap1/board-nokia770.c +++ b/arch/arm/mach-omap1/board-nokia770.c @@ -181,11 +181,7 @@ static struct omap_usb_config nokia770_usb_config __initdata = { static int nokia770_mmc_set_power(struct device *dev, int slot, int power_on, int vdd) { - if (power_on) - gpio_set_value(NOKIA770_GPIO_MMC_POWER, 1); - else - gpio_set_value(NOKIA770_GPIO_MMC_POWER, 0); - + gpio_set_value(NOKIA770_GPIO_MMC_POWER, power_on); return 0; } diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c index d040c3f1027..a2d7814896b 100644 --- a/arch/arm/mach-omap1/mcbsp.c +++ b/arch/arm/mach-omap1/mcbsp.c @@ -40,8 +40,8 @@ static void omap1_mcbsp_request(unsigned int id) */ if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3) { if (dsp_use++ == 0) { - api_clk = clk_get(NULL, "api_clk"); - dsp_clk = clk_get(NULL, "dsp_clk"); + api_clk = clk_get(NULL, "api_ck"); + dsp_clk = clk_get(NULL, "dsp_ck"); if (!IS_ERR(api_clk) && !IS_ERR(dsp_clk)) { clk_enable(api_clk); clk_enable(dsp_clk); diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index a0267a9ab46..e7d017cdc43 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -33,10 +33,8 @@ #include <mach/control.h> #include <mach/gpio.h> -#include <mach/gpioexpander.h> #include <mach/mux.h> #include <mach/usb.h> -#include <mach/irda.h> #include <mach/board.h> #include <mach/common.h> #include <mach/keypad.h> @@ -138,98 +136,6 @@ static struct platform_device h4_flash_device = { .resource = &h4_flash_resource, }; -/* Select between the IrDA and aGPS module - */ -static int h4_select_irda(struct device *dev, int state) -{ - unsigned char expa; - int err = 0; - - if ((err = read_gpio_expa(&expa, 0x21))) { - printk(KERN_ERR "Error reading from I/O expander\n"); - return err; - } - - /* 'P6' enable/disable IRDA_TX and IRDA_RX */ - if (state & IR_SEL) { /* IrDa */ - if ((err = write_gpio_expa(expa | 0x01, 0x21))) { - printk(KERN_ERR "Error writing to I/O expander\n"); - return err; - } - } else { - if ((err = write_gpio_expa(expa & ~0x01, 0x21))) { - printk(KERN_ERR "Error writing to I/O expander\n"); - return err; - } - } - return err; -} - -static void set_trans_mode(struct work_struct *work) -{ - struct omap_irda_config *irda_config = - container_of(work, struct omap_irda_config, gpio_expa.work); - int mode = irda_config->mode; - unsigned char expa; - int err = 0; - - if ((err = read_gpio_expa(&expa, 0x20)) != 0) { - printk(KERN_ERR "Error reading from I/O expander\n"); - } - - expa &= ~0x01; - - if (!(mode & IR_SIRMODE)) { /* MIR/FIR */ - expa |= 0x01; - } - - if ((err = write_gpio_expa(expa, 0x20)) != 0) { - printk(KERN_ERR "Error writing to I/O expander\n"); - } -} - -static int h4_transceiver_mode(struct device *dev, int mode) -{ - struct omap_irda_config *irda_config = dev->platform_data; - - irda_config->mode = mode; - cancel_delayed_work(&irda_config->gpio_expa); - PREPARE_DELAYED_WORK(&irda_config->gpio_expa, set_trans_mode); - schedule_delayed_work(&irda_config->gpio_expa, 0); - - return 0; -} - -static struct omap_irda_config h4_irda_data = { - .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE, - .transceiver_mode = h4_transceiver_mode, - .select_irda = h4_select_irda, - .rx_channel = OMAP24XX_DMA_UART3_RX, - .tx_channel = OMAP24XX_DMA_UART3_TX, - .dest_start = OMAP_UART3_BASE, - .src_start = OMAP_UART3_BASE, - .tx_trigger = OMAP24XX_DMA_UART3_TX, - .rx_trigger = OMAP24XX_DMA_UART3_RX, -}; - -static struct resource h4_irda_resources[] = { - [0] = { - .start = INT_24XX_UART3_IRQ, - .end = INT_24XX_UART3_IRQ, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device h4_irda_device = { - .name = "omapirda", - .id = -1, - .dev = { - .platform_data = &h4_irda_data, - }, - .num_resources = 1, - .resource = h4_irda_resources, -}; - static struct omap_kp_platform_data h4_kp_data = { .rows = 6, .cols = 7, @@ -255,7 +161,6 @@ static struct platform_device h4_lcd_device = { static struct platform_device *h4_devices[] __initdata = { &h4_flash_device, - &h4_irda_device, &h4_kp_device, &h4_lcd_device, }; diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 744740ae1b9..3a7a29d1f9a 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -42,6 +42,7 @@ #include <mach/nand.h> #include <mach/mux.h> #include <mach/usb.h> +#include <mach/timer-gp.h> #include "mmc-twl4030.h" @@ -186,6 +187,9 @@ static void __init omap3_beagle_init_irq(void) { omap2_init_common_hw(NULL); omap_init_irq(); +#ifdef CONFIG_OMAP_32K_TIMER + omap2_gp_clockevent_set_gptimer(12); +#endif omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index 3a0daac6c83..374ff63c3eb 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -15,7 +15,6 @@ #include <linux/err.h> #include <linux/clk.h> #include <linux/io.h> -#include <linux/delay.h> #include <linux/gpio.h> #include <mach/hardware.h> diff --git a/arch/arm/mach-omap2/clock24xx.c b/arch/arm/mach-omap2/clock24xx.c index 1e839c5a28c..efc59c49341 100644 --- a/arch/arm/mach-omap2/clock24xx.c +++ b/arch/arm/mach-omap2/clock24xx.c @@ -60,12 +60,13 @@ struct omap_clk { }, \ } -#define CK_243X (1 << 0) -#define CK_242X (1 << 1) +#define CK_243X RATE_IN_243X +#define CK_242X RATE_IN_242X static struct omap_clk omap24xx_clks[] = { /* external root sources */ CLK(NULL, "func_32k_ck", &func_32k_ck, CK_243X | CK_242X), + CLK(NULL, "secure_32k_ck", &secure_32k_ck, CK_243X | CK_242X), CLK(NULL, "osc_ck", &osc_ck, CK_243X | CK_242X), CLK(NULL, "sys_ck", &sys_ck, CK_243X | CK_242X), CLK(NULL, "alt_ck", &alt_ck, CK_243X | CK_242X), @@ -711,7 +712,7 @@ int __init omap2_clk_init(void) { struct prcm_config *prcm; struct omap_clk *c; - u32 clkrate, cpu_mask; + u32 clkrate; if (cpu_is_omap242x()) cpu_mask = RATE_IN_242X; @@ -720,21 +721,15 @@ int __init omap2_clk_init(void) clk_init(&omap2_clk_functions); + for (c = omap24xx_clks; c < omap24xx_clks + ARRAY_SIZE(omap24xx_clks); c++) + clk_init_one(c->lk.clk); + osc_ck.rate = omap2_osc_clk_recalc(&osc_ck); propagate_rate(&osc_ck); sys_ck.rate = omap2_sys_clk_recalc(&sys_ck); propagate_rate(&sys_ck); for (c = omap24xx_clks; c < omap24xx_clks + ARRAY_SIZE(omap24xx_clks); c++) - clk_init_one(c->lk.clk); - - cpu_mask = 0; - if (cpu_is_omap2420()) - cpu_mask |= CK_242X; - if (cpu_is_omap2430()) - cpu_mask |= CK_243X; - - for (c = omap24xx_clks; c < omap24xx_clks + ARRAY_SIZE(omap24xx_clks); c++) if (c->cpu & cpu_mask) { clkdev_add(&c->lk); clk_register(c->lk.clk); diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h index 33c3e5b1432..88c5acb40fc 100644 --- a/arch/arm/mach-omap2/clock24xx.h +++ b/arch/arm/mach-omap2/clock24xx.h @@ -625,6 +625,14 @@ static struct clk func_32k_ck = { .clkdm_name = "wkup_clkdm", }; +static struct clk secure_32k_ck = { + .name = "secure_32k_ck", + .ops = &clkops_null, + .rate = 32768, + .flags = RATE_FIXED, + .clkdm_name = "wkup_clkdm", +}; + /* Typical 12/13MHz in standalone mode, will be 26Mhz in chassis mode */ static struct clk osc_ck = { /* (*12, *13, 19.2, *26, 38.4)MHz */ .name = "osc_ck", @@ -1790,7 +1798,7 @@ static struct clk gpt12_ick = { static struct clk gpt12_fck = { .name = "gpt12_fck", .ops = &clkops_omap2_dflt_wait, - .parent = &func_32k_ck, + .parent = &secure_32k_ck, .clkdm_name = "core_l4_clkdm", .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), .enable_bit = OMAP24XX_EN_GPT12_SHIFT, diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h index 70ec10deb65..6763b8f7302 100644 --- a/arch/arm/mach-omap2/clock34xx.h +++ b/arch/arm/mach-omap2/clock34xx.h @@ -2052,7 +2052,7 @@ static struct clk dss_ick = { static struct clk cam_mclk = { .name = "cam_mclk", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, .parent = &dpll4_m5x2_ck, .enable_reg = OMAP_CM_REGADDR(OMAP3430_CAM_MOD, CM_FCLKEN), .enable_bit = OMAP3430_EN_CAM_SHIFT, @@ -2063,7 +2063,7 @@ static struct clk cam_mclk = { static struct clk cam_ick = { /* Handles both L3 and L4 clocks */ .name = "cam_ick", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, .parent = &l4_ick, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430_CAM_MOD, CM_ICLKEN), @@ -2074,7 +2074,7 @@ static struct clk cam_ick = { static struct clk csi2_96m_fck = { .name = "csi2_96m_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, .parent = &core_96m_fck, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430_CAM_MOD, CM_FCLKEN), @@ -2901,7 +2901,6 @@ static struct clk sr_l4_ick = { /* SECURE_32K_FCK clocks */ -/* XXX This clock no longer exists in 3430 TRM rev F */ static struct clk gpt12_fck = { .name = "gpt12_fck", .ops = &clkops_null, diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index d6b4b2f8722..496983ade97 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -25,7 +25,6 @@ #include <mach/board.h> #include <mach/mux.h> #include <mach/gpio.h> -#include <mach/eac.h> #include <mach/mmc.h> #if defined(CONFIG_VIDEO_OMAP2) || defined(CONFIG_VIDEO_OMAP2_MODULE) @@ -366,38 +365,6 @@ static void omap_init_mcspi(void) static inline void omap_init_mcspi(void) {} #endif -#ifdef CONFIG_SND_OMAP24XX_EAC - -#define OMAP2_EAC_BASE 0x48090000 - -static struct resource omap2_eac_resources[] = { - { - .start = OMAP2_EAC_BASE, - .end = OMAP2_EAC_BASE + 0x109, - .flags = IORESOURCE_MEM, - }, -}; - -static struct platform_device omap2_eac_device = { - .name = "omap24xx-eac", - .id = -1, - .num_resources = ARRAY_SIZE(omap2_eac_resources), - .resource = omap2_eac_resources, - .dev = { - .platform_data = NULL, - }, -}; - -void omap_init_eac(struct eac_platform_data *pdata) -{ - omap2_eac_device.dev.platform_data = pdata; - platform_device_register(&omap2_eac_device); -} - -#else -void omap_init_eac(struct eac_platform_data *pdata) {} -#endif - #ifdef CONFIG_OMAP_SHA1_MD5 static struct resource sha1_md5_resources[] = { { diff --git a/arch/arm/mach-omap2/irq.c b/arch/arm/mach-omap2/irq.c index 9ba20d985dd..998c5c45587 100644 --- a/arch/arm/mach-omap2/irq.c +++ b/arch/arm/mach-omap2/irq.c @@ -73,9 +73,9 @@ static int omap_check_spurious(unsigned int irq) u32 sir, spurious; sir = intc_bank_read_reg(&irq_banks[0], INTC_SIR); - spurious = sir >> 6; + spurious = sir >> 7; - if (spurious > 1) { + if (spurious) { printk(KERN_WARNING "Spurious irq %i: 0x%08x, please flush " "posted write for irq %i\n", irq, sir, previous_irq); diff --git a/arch/arm/mach-omap2/timer-gp.c b/arch/arm/mach-omap2/timer-gp.c index 1cb2c0909c2..f36aba12090 100644 --- a/arch/arm/mach-omap2/timer-gp.c +++ b/arch/arm/mach-omap2/timer-gp.c @@ -3,6 +3,8 @@ * * OMAP2 GP timer support. * + * Copyright (C) 2009 Nokia Corporation + * * Update to use new clocksource/clockevent layers * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com> * Copyright (C) 2007 MontaVista Software, Inc. @@ -36,8 +38,13 @@ #include <asm/mach/time.h> #include <mach/dmtimer.h> +/* MAX_GPTIMER_ID: number of GPTIMERs on the chip */ +#define MAX_GPTIMER_ID 12 + static struct omap_dm_timer *gptimer; static struct clock_event_device clockevent_gpt; +static u8 __initdata gptimer_id = 1; +static u8 __initdata inited; static irqreturn_t omap2_gp_timer_interrupt(int irq, void *dev_id) { @@ -95,20 +102,53 @@ static struct clock_event_device clockevent_gpt = { .set_mode = omap2_gp_timer_set_mode, }; +/** + * omap2_gp_clockevent_set_gptimer - set which GPTIMER is used for clockevents + * @id: GPTIMER to use (1..MAX_GPTIMER_ID) + * + * Define the GPTIMER that the system should use for the tick timer. + * Meant to be called from board-*.c files in the event that GPTIMER1, the + * default, is unsuitable. Returns -EINVAL on error or 0 on success. + */ +int __init omap2_gp_clockevent_set_gptimer(u8 id) +{ + if (id < 1 || id > MAX_GPTIMER_ID) + return -EINVAL; + + BUG_ON(inited); + + gptimer_id = id; + + return 0; +} + static void __init omap2_gp_clockevent_init(void) { u32 tick_rate; + int src; + + inited = 1; - gptimer = omap_dm_timer_request_specific(1); + gptimer = omap_dm_timer_request_specific(gptimer_id); BUG_ON(gptimer == NULL); #if defined(CONFIG_OMAP_32K_TIMER) - omap_dm_timer_set_source(gptimer, OMAP_TIMER_SRC_32_KHZ); + src = OMAP_TIMER_SRC_32_KHZ; #else - omap_dm_timer_set_source(gptimer, OMAP_TIMER_SRC_SYS_CLK); + src = OMAP_TIMER_SRC_SYS_CLK; + WARN(gptimer_id == 12, "WARNING: GPTIMER12 can only use the " + "secure 32KiHz clock source\n"); #endif + + if (gptimer_id != 12) + WARN(IS_ERR_VALUE(omap_dm_timer_set_source(gptimer, src)), + "timer-gp: omap_dm_timer_set_source() failed\n"); + tick_rate = clk_get_rate(omap_dm_timer_get_fclk(gptimer)); + pr_info("OMAP clockevent source: GPTIMER%d at %u Hz\n", + gptimer_id, tick_rate); + omap2_gp_timer_irq.dev_id = (void *)gptimer; setup_irq(omap_dm_timer_get_irq(gptimer), &omap2_gp_timer_irq); omap_dm_timer_set_int_enable(gptimer, OMAP_TIMER_INT_OVERFLOW); @@ -125,6 +165,8 @@ static void __init omap2_gp_clockevent_init(void) clockevents_register_device(&clockevent_gpt); } +/* Clocksource code */ + #ifdef CONFIG_OMAP_32K_TIMER /* * When 32k-timer is enabled, don't use GPTimer for clocksource diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c index 15e509013de..8df55f40f4c 100644 --- a/arch/arm/mach-omap2/usb-tusb6010.c +++ b/arch/arm/mach-omap2/usb-tusb6010.c @@ -187,7 +187,7 @@ int tusb6010_platform_retime(unsigned is_refclk) unsigned sysclk_ps; int status; - if (!refclk_psec) + if (!refclk_psec || sysclk_ps == 0) return -ENODEV; sysclk_ps = is_refclk ? refclk_psec : TUSB6010_OSCCLK_60; diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c index cdf21dd135b..930e364ccde 100644 --- a/arch/arm/mach-pxa/corgi.c +++ b/arch/arm/mach-pxa/corgi.c @@ -427,12 +427,22 @@ static struct pxa2xx_spi_master corgi_spi_info = { .num_chipselect = 3, }; +static void corgi_wait_for_hsync(void) +{ + while (gpio_get_value(CORGI_GPIO_HSYNC)) + cpu_relax(); + + while (!gpio_get_value(CORGI_GPIO_HSYNC)) + cpu_relax(); +} + static struct ads7846_platform_data corgi_ads7846_info = { .model = 7846, .vref_delay_usecs = 100, .x_plate_ohms = 419, .y_plate_ohms = 486, .gpio_pendown = CORGI_GPIO_TP_INT, + .wait_for_sync = corgi_wait_for_hsync, }; static void corgi_ads7846_cs(u32 command) diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c index e13f6a81c22..c872b9feb4d 100644 --- a/arch/arm/mach-pxa/littleton.c +++ b/arch/arm/mach-pxa/littleton.c @@ -334,6 +334,11 @@ static struct led_info littleton_da9034_leds[] = { }, }; +static struct da9034_touch_pdata littleton_da9034_touch = { + .x_inverted = 1, + .interval_ms = 20, +}; + static struct da903x_subdev_info littleton_da9034_subdevs[] = { { .name = "da903x-led", @@ -350,6 +355,10 @@ static struct da903x_subdev_info littleton_da9034_subdevs[] = { }, { .name = "da903x-backlight", .id = DA9034_ID_WLED, + }, { + .name = "da9034-touch", + .id = DA9034_ID_TOUCH, + .platform_data = &littleton_da9034_touch, }, }; diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index 8c61ddac119..c18e34acafc 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -299,12 +299,22 @@ static struct pxa2xx_spi_master spitz_spi_info = { .num_chipselect = 3, }; +static void spitz_wait_for_hsync(void) +{ + while (gpio_get_value(SPITZ_GPIO_HSYNC)) + cpu_relax(); + + while (!gpio_get_value(SPITZ_GPIO_HSYNC)) + cpu_relax(); +} + static struct ads7846_platform_data spitz_ads7846_info = { .model = 7846, .vref_delay_usecs = 100, .x_plate_ohms = 419, .y_plate_ohms = 486, .gpio_pendown = SPITZ_GPIO_TP_INT, + .wait_for_sync = spitz_wait_for_hsync, }; static void spitz_ads7846_cs(u32 command) diff --git a/arch/arm/mach-pxa/zylonite_pxa300.c b/arch/arm/mach-pxa/zylonite_pxa300.c index c1f73205d07..c256c57642c 100644 --- a/arch/arm/mach-pxa/zylonite_pxa300.c +++ b/arch/arm/mach-pxa/zylonite_pxa300.c @@ -72,6 +72,7 @@ static mfp_cfg_t common_mfp_cfg[] __initdata = { GPIO25_AC97_SDATA_IN_0, GPIO27_AC97_SDATA_OUT, GPIO28_AC97_SYNC, + GPIO17_GPIO, /* SDATA_IN_1 but unused - configure to GPIO */ /* SSP3 */ GPIO91_SSP3_SCLK, @@ -126,6 +127,10 @@ static mfp_cfg_t common_mfp_cfg[] __initdata = { /* Standard I2C */ GPIO21_I2C_SCL, GPIO22_I2C_SDA, + + /* GPIO */ + GPIO18_GPIO, /* GPIO Expander #0 INT_N */ + GPIO19_GPIO, /* GPIO Expander #1 INT_N */ }; static mfp_cfg_t pxa300_mfp_cfg[] __initdata = { diff --git a/arch/arm/mach-pxa/zylonite_pxa320.c b/arch/arm/mach-pxa/zylonite_pxa320.c index 4e1c488c690..cc5a2283360 100644 --- a/arch/arm/mach-pxa/zylonite_pxa320.c +++ b/arch/arm/mach-pxa/zylonite_pxa320.c @@ -68,6 +68,7 @@ static mfp_cfg_t mfp_cfg[] __initdata = { GPIO38_AC97_SYNC, GPIO39_AC97_BITCLK, GPIO40_AC97_nACRESET, + GPIO36_GPIO, /* SDATA_IN_1 but unused - configure to GPIO */ /* SSP3 */ GPIO89_SSP3_SCLK, diff --git a/arch/arm/mach-sa1100/lart.c b/arch/arm/mach-sa1100/lart.c index 0cd52692d2f..1f940df0e5a 100644 --- a/arch/arm/mach-sa1100/lart.c +++ b/arch/arm/mach-sa1100/lart.c @@ -9,6 +9,7 @@ #include <mach/hardware.h> #include <asm/setup.h> #include <asm/mach-types.h> +#include <asm/page.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> diff --git a/arch/arm/mm/cache-v6.S b/arch/arm/mm/cache-v6.S index 2c6c2a7c05a..8f5c13f4c93 100644 --- a/arch/arm/mm/cache-v6.S +++ b/arch/arm/mm/cache-v6.S @@ -20,6 +20,31 @@ #define D_CACHE_LINE_SIZE 32 #define BTB_FLUSH_SIZE 8 +#ifdef CONFIG_ARM_ERRATA_411920 +/* + * Invalidate the entire I cache (this code is a workaround for the ARM1136 + * erratum 411920 - Invalidate Instruction Cache operation can fail. This + * erratum is present in 1136, 1156 and 1176. It does not affect the MPCore. + * + * Registers: + * r0 - set to 0 + * r1 - corrupted + */ +ENTRY(v6_icache_inval_all) + mov r0, #0 + mrs r1, cpsr + cpsid ifa @ disable interrupts + mcr p15, 0, r0, c7, c5, 0 @ invalidate entire I-cache + mcr p15, 0, r0, c7, c5, 0 @ invalidate entire I-cache + mcr p15, 0, r0, c7, c5, 0 @ invalidate entire I-cache + mcr p15, 0, r0, c7, c5, 0 @ invalidate entire I-cache + msr cpsr_cx, r1 @ restore interrupts + .rept 11 @ ARM Ltd recommends at least + nop @ 11 NOPs + .endr + mov pc, lr +#endif + /* * v6_flush_cache_all() * @@ -31,8 +56,12 @@ ENTRY(v6_flush_kern_cache_all) mov r0, #0 #ifdef HARVARD_CACHE mcr p15, 0, r0, c7, c14, 0 @ D cache clean+invalidate +#ifndef CONFIG_ARM_ERRATA_411920 mcr p15, 0, r0, c7, c5, 0 @ I+BTB cache invalidate #else + b v6_icache_inval_all +#endif +#else mcr p15, 0, r0, c7, c15, 0 @ Cache clean+invalidate #endif mov pc, lr @@ -103,8 +132,12 @@ ENTRY(v6_coherent_user_range) mov r0, #0 #ifdef HARVARD_CACHE mcr p15, 0, r0, c7, c10, 4 @ drain write buffer +#ifndef CONFIG_ARM_ERRATA_411920 mcr p15, 0, r0, c7, c5, 0 @ I+BTB cache invalidate #else + b v6_icache_inval_all +#endif +#else mcr p15, 0, r0, c7, c5, 6 @ invalidate BTB #endif mov pc, lr diff --git a/arch/arm/mm/flush.c b/arch/arm/mm/flush.c index 4e283481cee..c07222eb5ce 100644 --- a/arch/arm/mm/flush.c +++ b/arch/arm/mm/flush.c @@ -18,6 +18,10 @@ #include "mm.h" +#ifdef CONFIG_ARM_ERRATA_411920 +extern void v6_icache_inval_all(void); +#endif + #ifdef CONFIG_CPU_CACHE_VIPT #define ALIAS_FLUSH_START 0xffff4000 @@ -32,10 +36,15 @@ static void flush_pfn_alias(unsigned long pfn, unsigned long vaddr) asm( "mcrr p15, 0, %1, %0, c14\n" " mcr p15, 0, %2, c7, c10, 4\n" +#ifndef CONFIG_ARM_ERRATA_411920 " mcr p15, 0, %2, c7, c5, 0\n" +#endif : : "r" (to), "r" (to + PAGE_SIZE - L1_CACHE_BYTES), "r" (zero) : "cc"); +#ifdef CONFIG_ARM_ERRATA_411920 + v6_icache_inval_all(); +#endif } void flush_cache_mm(struct mm_struct *mm) @@ -48,11 +57,16 @@ void flush_cache_mm(struct mm_struct *mm) if (cache_is_vipt_aliasing()) { asm( "mcr p15, 0, %0, c7, c14, 0\n" + " mcr p15, 0, %0, c7, c10, 4\n" +#ifndef CONFIG_ARM_ERRATA_411920 " mcr p15, 0, %0, c7, c5, 0\n" - " mcr p15, 0, %0, c7, c10, 4" +#endif : : "r" (0) : "cc"); +#ifdef CONFIG_ARM_ERRATA_411920 + v6_icache_inval_all(); +#endif } } @@ -67,11 +81,16 @@ void flush_cache_range(struct vm_area_struct *vma, unsigned long start, unsigned if (cache_is_vipt_aliasing()) { asm( "mcr p15, 0, %0, c7, c14, 0\n" + " mcr p15, 0, %0, c7, c10, 4\n" +#ifndef CONFIG_ARM_ERRATA_411920 " mcr p15, 0, %0, c7, c5, 0\n" - " mcr p15, 0, %0, c7, c10, 4" +#endif : : "r" (0) : "cc"); +#ifdef CONFIG_ARM_ERRATA_411920 + v6_icache_inval_all(); +#endif } } diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S index f0cc599facb..087e239704d 100644 --- a/arch/arm/mm/proc-v6.S +++ b/arch/arm/mm/proc-v6.S @@ -10,6 +10,7 @@ * * This is the "shell" of the ARMv6 processor support. */ +#include <linux/init.h> #include <linux/linkage.h> #include <asm/assembler.h> #include <asm/asm-offsets.h> @@ -132,7 +133,7 @@ cpu_v6_name: .asciz "ARMv6-compatible processor" .align - .section ".text.init", #alloc, #execinstr + __INIT /* * __v6_setup diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S index d1ebec42521..3397f1e64d7 100644 --- a/arch/arm/mm/proc-v7.S +++ b/arch/arm/mm/proc-v7.S @@ -9,6 +9,7 @@ * * This is the "shell" of the ARMv7 processor support. */ +#include <linux/init.h> #include <linux/linkage.h> #include <asm/assembler.h> #include <asm/asm-offsets.h> @@ -95,6 +96,9 @@ ENTRY(cpu_v7_switch_mm) mov r2, #0 ldr r1, [r1, #MM_CONTEXT_ID] @ get mm->context.id orr r0, r0, #TTB_FLAGS +#ifdef CONFIG_ARM_ERRATA_430973 + mcr p15, 0, r2, c7, c5, 6 @ flush BTAC/BTB +#endif mcr p15, 0, r2, c13, c0, 1 @ set reserved context ID isb 1: mcr p15, 0, r0, c2, c0, 0 @ set TTB 0 @@ -153,7 +157,7 @@ cpu_v7_name: .ascii "ARMv7 Processor" .align - .section ".text.init", #alloc, #execinstr + __INIT /* * __v7_setup @@ -180,6 +184,22 @@ __v7_setup: stmia r12, {r0-r5, r7, r9, r11, lr} bl v7_flush_dcache_all ldmia r12, {r0-r5, r7, r9, r11, lr} +#ifdef CONFIG_ARM_ERRATA_430973 + mrc p15, 0, r10, c1, c0, 1 @ read aux control register + orr r10, r10, #(1 << 6) @ set IBE to 1 + mcr p15, 0, r10, c1, c0, 1 @ write aux control register +#endif +#ifdef CONFIG_ARM_ERRATA_458693 + mrc p15, 0, r10, c1, c0, 1 @ read aux control register + orr r10, r10, #(1 << 5) @ set L1NEON to 1 + orr r10, r10, #(1 << 9) @ set PLDNOP to 1 + mcr p15, 0, r10, c1, c0, 1 @ write aux control register +#endif +#ifdef CONFIG_ARM_ERRATA_460075 + mrc p15, 1, r10, c9, c0, 2 @ read L2 cache aux ctrl register + orr r10, r10, #(1 << 22) @ set the Write Allocate disable bit + mcr p15, 1, r10, c9, c0, 2 @ write the L2 cache aux ctrl register +#endif mov r10, #0 #ifdef HARVARD_CACHE mcr p15, 0, r10, c7, c5, 0 @ I+BTB cache invalidate diff --git a/arch/arm/mm/tlb-v6.S b/arch/arm/mm/tlb-v6.S index 20f84bbaa9b..73d7d89b04c 100644 --- a/arch/arm/mm/tlb-v6.S +++ b/arch/arm/mm/tlb-v6.S @@ -10,6 +10,7 @@ * ARM architecture version 6 TLB handling functions. * These assume a split I/D TLB. */ +#include <linux/init.h> #include <linux/linkage.h> #include <asm/asm-offsets.h> #include <asm/page.h> @@ -87,7 +88,7 @@ ENTRY(v6wbi_flush_kern_tlb_range) mcr p15, 0, r2, c7, c5, 4 @ prefetch flush mov pc, lr - .section ".text.init", #alloc, #execinstr + __INIT .type v6wbi_tlb_fns, #object ENTRY(v6wbi_tlb_fns) diff --git a/arch/arm/mm/tlb-v7.S b/arch/arm/mm/tlb-v7.S index 24ba5109f2e..b637e7380ab 100644 --- a/arch/arm/mm/tlb-v7.S +++ b/arch/arm/mm/tlb-v7.S @@ -11,6 +11,7 @@ * ARM architecture version 6 TLB handling functions. * These assume a split I/D TLB. */ +#include <linux/init.h> #include <linux/linkage.h> #include <asm/asm-offsets.h> #include <asm/page.h> @@ -80,7 +81,7 @@ ENTRY(v7wbi_flush_kern_tlb_range) mov pc, lr ENDPROC(v7wbi_flush_kern_tlb_range) - .section ".text.init", #alloc, #execinstr + __INIT .type v7wbi_tlb_fns, #object ENTRY(v7wbi_tlb_fns) diff --git a/arch/arm/plat-mxc/Kconfig b/arch/arm/plat-mxc/Kconfig index 17d0e9906d5..8986b741223 100644 --- a/arch/arm/plat-mxc/Kconfig +++ b/arch/arm/plat-mxc/Kconfig @@ -48,7 +48,14 @@ config MXC_IRQ_PRIOR config MXC_PWM tristate "Enable PWM driver" depends on ARCH_MXC + select HAVE_PWM help Enable support for the i.MX PWM controller(s). +config ARCH_HAS_RNGA + bool + depends on ARCH_MXC + +config ARCH_MXC_IOMUX_V3 + bool endif diff --git a/arch/arm/plat-mxc/Makefile b/arch/arm/plat-mxc/Makefile index 055406312b6..e3212c8ff42 100644 --- a/arch/arm/plat-mxc/Makefile +++ b/arch/arm/plat-mxc/Makefile @@ -7,4 +7,5 @@ obj-y := irq.o clock.o gpio.o time.o devices.o cpu.o system.o obj-$(CONFIG_ARCH_MX1) += iomux-mx1-mx2.o dma-mx1-mx2.o obj-$(CONFIG_ARCH_MX2) += iomux-mx1-mx2.o dma-mx1-mx2.o +obj-$(CONFIG_ARCH_MXC_IOMUX_V3) += iomux-v3.o obj-$(CONFIG_MXC_PWM) += pwm.o diff --git a/arch/arm/plat-mxc/dma-mx1-mx2.c b/arch/arm/plat-mxc/dma-mx1-mx2.c index e364a5ed10f..77646436c00 100644 --- a/arch/arm/plat-mxc/dma-mx1-mx2.c +++ b/arch/arm/plat-mxc/dma-mx1-mx2.c @@ -693,12 +693,15 @@ int imx_dma_request(int channel, const char *name) local_irq_restore(flags); return -EBUSY; } + memset(imxdma, 0, sizeof(imxdma)); + imxdma->name = name; + local_irq_restore(flags); /* request_irq() can block */ #ifdef CONFIG_ARCH_MX2 ret = request_irq(MXC_INT_DMACH0 + channel, dma_irq_handler, 0, "DMA", NULL); if (ret) { - local_irq_restore(flags); + imxdma->name = NULL; printk(KERN_CRIT "Can't register IRQ %d for DMA channel %d\n", MXC_INT_DMACH0 + channel, channel); return ret; @@ -708,13 +711,6 @@ int imx_dma_request(int channel, const char *name) imxdma->watchdog.data = channel; #endif - imxdma->name = name; - imxdma->irq_handler = NULL; - imxdma->err_handler = NULL; - imxdma->data = NULL; - imxdma->sg = NULL; - - local_irq_restore(flags); return ret; } EXPORT_SYMBOL(imx_dma_request); @@ -737,10 +733,7 @@ void imx_dma_free(int channel) local_irq_save(flags); /* Disable interrupts */ - __raw_writel(__raw_readl(DMA_BASE + DMA_DIMR) | (1 << channel), - DMA_BASE + DMA_DIMR); - __raw_writel(__raw_readl(DMA_BASE + DMA_CCR(channel)) & ~CCR_CEN, - DMA_BASE + DMA_CCR(channel)); + imx_dma_disable(channel); imxdma->name = NULL; #ifdef CONFIG_ARCH_MX2 diff --git a/arch/arm/plat-mxc/gpio.c b/arch/arm/plat-mxc/gpio.c index c6483bad8a2..7506d963be4 100644 --- a/arch/arm/plat-mxc/gpio.c +++ b/arch/arm/plat-mxc/gpio.c @@ -64,6 +64,8 @@ static void gpio_unmask_irq(u32 irq) _set_gpio_irqenable(&mxc_gpio_ports[gpio / 32], gpio & 0x1f, 1); } +static int mxc_gpio_get(struct gpio_chip *chip, unsigned offset); + static int gpio_set_irq_type(u32 irq, u32 type) { u32 gpio = irq_to_gpio(irq); @@ -72,6 +74,7 @@ static int gpio_set_irq_type(u32 irq, u32 type) int edge; void __iomem *reg = port->base; + port->both_edges &= ~(1 << (gpio & 31)); switch (type) { case IRQ_TYPE_EDGE_RISING: edge = GPIO_INT_RISE_EDGE; @@ -79,13 +82,24 @@ static int gpio_set_irq_type(u32 irq, u32 type) case IRQ_TYPE_EDGE_FALLING: edge = GPIO_INT_FALL_EDGE; break; + case IRQ_TYPE_EDGE_BOTH: + val = mxc_gpio_get(&port->chip, gpio & 31); + if (val) { + edge = GPIO_INT_LOW_LEV; + pr_debug("mxc: set GPIO %d to low trigger\n", gpio); + } else { + edge = GPIO_INT_HIGH_LEV; + pr_debug("mxc: set GPIO %d to high trigger\n", gpio); + } + port->both_edges |= 1 << (gpio & 31); + break; case IRQ_TYPE_LEVEL_LOW: edge = GPIO_INT_LOW_LEV; break; case IRQ_TYPE_LEVEL_HIGH: edge = GPIO_INT_HIGH_LEV; break; - default: /* this includes IRQ_TYPE_EDGE_BOTH */ + default: return -EINVAL; } @@ -98,6 +112,34 @@ static int gpio_set_irq_type(u32 irq, u32 type) return 0; } +static void mxc_flip_edge(struct mxc_gpio_port *port, u32 gpio) +{ + void __iomem *reg = port->base; + u32 bit, val; + int edge; + + reg += GPIO_ICR1 + ((gpio & 0x10) >> 2); /* lower or upper register */ + bit = gpio & 0xf; + val = __raw_readl(reg); + edge = (val >> (bit << 1)) & 3; + val &= ~(0x3 << (bit << 1)); + switch (edge) { + case GPIO_INT_HIGH_LEV: + edge = GPIO_INT_LOW_LEV; + pr_debug("mxc: switch GPIO %d to low trigger\n", gpio); + break; + case GPIO_INT_LOW_LEV: + edge = GPIO_INT_HIGH_LEV; + pr_debug("mxc: switch GPIO %d to high trigger\n", gpio); + break; + default: + pr_err("mxc: invalid configuration for GPIO %d: %x\n", + gpio, edge); + return; + } + __raw_writel(val | (edge << (bit << 1)), reg); +} + /* handle n interrupts in one status register */ static void mxc_gpio_irq_handler(struct mxc_gpio_port *port, u32 irq_stat) { @@ -105,11 +147,16 @@ static void mxc_gpio_irq_handler(struct mxc_gpio_port *port, u32 irq_stat) gpio_irq_no = port->virtual_irq_start; for (; irq_stat != 0; irq_stat >>= 1, gpio_irq_no++) { + u32 gpio = irq_to_gpio(gpio_irq_no); if ((irq_stat & 1) == 0) continue; BUG_ON(!(irq_desc[gpio_irq_no].handle_irq)); + + if (port->both_edges & (1 << (gpio & 31))) + mxc_flip_edge(port, gpio); + irq_desc[gpio_irq_no].handle_irq(gpio_irq_no, &irq_desc[gpio_irq_no]); } @@ -124,7 +171,7 @@ static void mx3_gpio_irq_handler(u32 irq, struct irq_desc *desc) irq_stat = __raw_readl(port->base + GPIO_ISR) & __raw_readl(port->base + GPIO_IMR); - BUG_ON(!irq_stat); + mxc_gpio_irq_handler(port, irq_stat); } #endif diff --git a/arch/arm/plat-mxc/include/mach/board-mx21ads.h b/arch/arm/plat-mxc/include/mach/board-mx21ads.h new file mode 100644 index 00000000000..06701df74c4 --- /dev/null +++ b/arch/arm/plat-mxc/include/mach/board-mx21ads.h @@ -0,0 +1,58 @@ +/* + * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved. + */ + +/* + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __ASM_ARCH_MXC_BOARD_MX21ADS_H__ +#define __ASM_ARCH_MXC_BOARD_MX21ADS_H__ + +/* + * MXC UART EVB board level configurations + */ +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR AIPI_IO_ADDRESS(UART1_BASE_ADDR) + +/* + * Memory-mapped I/O on MX21ADS base board + */ +#define MX21ADS_MMIO_BASE_ADDR 0xF5000000 +#define MX21ADS_MMIO_SIZE SZ_16M + +#define MX21ADS_REG_ADDR(offset) (void __force __iomem *) \ + (MX21ADS_MMIO_BASE_ADDR + (offset)) + +#define MX21ADS_CS8900A_IRQ IRQ_GPIOE(11) +#define MX21ADS_CS8900A_IOBASE_REG MX21ADS_REG_ADDR(0x000000) +#define MX21ADS_ST16C255_IOBASE_REG MX21ADS_REG_ADDR(0x200000) +#define MX21ADS_VERSION_REG MX21ADS_REG_ADDR(0x400000) +#define MX21ADS_IO_REG MX21ADS_REG_ADDR(0x800000) + +/* MX21ADS_IO_REG bit definitions */ +#define MX21ADS_IO_SD_WP 0x0001 /* read */ +#define MX21ADS_IO_TP6 0x0001 /* write */ +#define MX21ADS_IO_SW_SEL 0x0002 /* read */ +#define MX21ADS_IO_TP7 0x0002 /* write */ +#define MX21ADS_IO_RESET_E_UART 0x0004 +#define MX21ADS_IO_RESET_BASE 0x0008 +#define MX21ADS_IO_CSI_CTL2 0x0010 +#define MX21ADS_IO_CSI_CTL1 0x0020 +#define MX21ADS_IO_CSI_CTL0 0x0040 +#define MX21ADS_IO_UART1_EN 0x0080 +#define MX21ADS_IO_UART4_EN 0x0100 +#define MX21ADS_IO_LCDON 0x0200 +#define MX21ADS_IO_IRDA_EN 0x0400 +#define MX21ADS_IO_IRDA_FIR_SEL 0x0800 +#define MX21ADS_IO_IRDA_MD0_B 0x1000 +#define MX21ADS_IO_IRDA_MD1 0x2000 +#define MX21ADS_IO_LED4_ON 0x4000 +#define MX21ADS_IO_LED3_ON 0x8000 + +#endif /* __ASM_ARCH_MXC_BOARD_MX21ADS_H__ */ diff --git a/arch/arm/plat-mxc/include/mach/board-mx27ads.h b/arch/arm/plat-mxc/include/mach/board-mx27ads.h index 1cac9d1135c..d42f4e6116f 100644 --- a/arch/arm/plat-mxc/include/mach/board-mx27ads.h +++ b/arch/arm/plat-mxc/include/mach/board-mx27ads.h @@ -47,7 +47,7 @@ /* * Base address of PBC controller, CS4 */ -#define PBC_BASE_ADDRESS 0xEB000000 +#define PBC_BASE_ADDRESS 0xf4300000 #define PBC_REG_ADDR(offset) (void __force __iomem *) \ (PBC_BASE_ADDRESS + (offset)) diff --git a/arch/arm/plat-mxc/include/mach/board-mx27pdk.h b/arch/arm/plat-mxc/include/mach/board-mx27pdk.h new file mode 100644 index 00000000000..552b55d714d --- /dev/null +++ b/arch/arm/plat-mxc/include/mach/board-mx27pdk.h @@ -0,0 +1,19 @@ +/* + * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved. + */ + +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_MXC_BOARD_MX27PDK_H__ +#define __ASM_ARCH_MXC_BOARD_MX27PDK_H__ + +/* mandatory for CONFIG_DEBUG_LL */ + +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) + +#endif /* __ASM_ARCH_MXC_BOARD_MX27PDK_H__ */ diff --git a/arch/arm/plat-mxc/include/mach/board-mx31ads.h b/arch/arm/plat-mxc/include/mach/board-mx31ads.h index 318c72ada13..06e6895f7f6 100644 --- a/arch/arm/plat-mxc/include/mach/board-mx31ads.h +++ b/arch/arm/plat-mxc/include/mach/board-mx31ads.h @@ -114,7 +114,7 @@ #define MXC_MAX_EXP_IO_LINES 16 -/* mandatory for CONFIG_LL_DEBUG */ +/* mandatory for CONFIG_DEBUG_LL */ #define MXC_LL_UART_PADDR UART1_BASE_ADDR #define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) diff --git a/arch/arm/plat-mxc/include/mach/board-mx31lite.h b/arch/arm/plat-mxc/include/mach/board-mx31lite.h index e4e5cf5ad7d..52fbdf2d6f2 100644 --- a/arch/arm/plat-mxc/include/mach/board-mx31lite.h +++ b/arch/arm/plat-mxc/include/mach/board-mx31lite.h @@ -11,28 +11,8 @@ #ifndef __ASM_ARCH_MXC_BOARD_MX31LITE_H__ #define __ASM_ARCH_MXC_BOARD_MX31LITE_H__ -#define MXC_MAX_EXP_IO_LINES 16 - - -/* - * Memory Size parameters - */ - -/* - * Size of SDRAM memory - */ -#define SDRAM_MEM_SIZE SZ_128M -/* - * Size of MBX buffer memory - */ -#define MXC_MBX_MEM_SIZE SZ_16M -/* - * Size of memory available to kernel - */ -#define MEM_SIZE (SDRAM_MEM_SIZE - MXC_MBX_MEM_SIZE) - #define MXC_LL_UART_PADDR UART1_BASE_ADDR #define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) -#endif /* __ASM_ARCH_MXC_BOARD_MX31ADS_H__ */ +#endif /* __ASM_ARCH_MXC_BOARD_MX31LITE_H__ */ diff --git a/arch/arm/plat-mxc/include/mach/board-mx31moboard.h b/arch/arm/plat-mxc/include/mach/board-mx31moboard.h index f8aef1babb7..303fd2434a2 100644 --- a/arch/arm/plat-mxc/include/mach/board-mx31moboard.h +++ b/arch/arm/plat-mxc/include/mach/board-mx31moboard.h @@ -19,7 +19,7 @@ #ifndef __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__ #define __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__ -/* mandatory for CONFIG_LL_DEBUG */ +/* mandatory for CONFIG_DEBUG_LL */ #define MXC_LL_UART_PADDR UART1_BASE_ADDR #define MXC_LL_UART_VADDR (AIPI_BASE_ADDR_VIRT + 0x0A000) diff --git a/arch/arm/plat-mxc/include/mach/board-mx31pdk.h b/arch/arm/plat-mxc/include/mach/board-mx31pdk.h index 2b6b316d0f5..519bab3eb28 100644 --- a/arch/arm/plat-mxc/include/mach/board-mx31pdk.h +++ b/arch/arm/plat-mxc/include/mach/board-mx31pdk.h @@ -11,9 +11,54 @@ #ifndef __ASM_ARCH_MXC_BOARD_MX31PDK_H__ #define __ASM_ARCH_MXC_BOARD_MX31PDK_H__ -/* mandatory for CONFIG_LL_DEBUG */ +/* mandatory for CONFIG_DEBUG_LL */ #define MXC_LL_UART_PADDR UART1_BASE_ADDR #define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) +/* Definitions for components on the Debug board */ + +/* Base address of CPLD controller on the Debug board */ +#define DEBUG_BASE_ADDRESS CS5_IO_ADDRESS(CS5_BASE_ADDR) + +/* LAN9217 ethernet base address */ +#define LAN9217_BASE_ADDR CS5_BASE_ADDR + +/* CPLD config and interrupt base address */ +#define CPLD_ADDR (DEBUG_BASE_ADDRESS + 0x20000) + +/* LED switchs */ +#define CPLD_LED_REG (CPLD_ADDR + 0x00) +/* buttons */ +#define CPLD_SWITCH_BUTTONS_REG (EXPIO_ADDR + 0x08) +/* status, interrupt */ +#define CPLD_INT_STATUS_REG (CPLD_ADDR + 0x10) +#define CPLD_INT_MASK_REG (CPLD_ADDR + 0x38) +#define CPLD_INT_RESET_REG (CPLD_ADDR + 0x20) +/* magic word for debug CPLD */ +#define CPLD_MAGIC_NUMBER1_REG (CPLD_ADDR + 0x40) +#define CPLD_MAGIC_NUMBER2_REG (CPLD_ADDR + 0x48) +/* CPLD code version */ +#define CPLD_CODE_VER_REG (CPLD_ADDR + 0x50) +/* magic word for debug CPLD */ +#define CPLD_MAGIC_NUMBER3_REG (CPLD_ADDR + 0x58) +/* module reset register */ +#define CPLD_MODULE_RESET_REG (CPLD_ADDR + 0x60) +/* CPU ID and Personality ID */ +#define CPLD_MCU_BOARD_ID_REG (CPLD_ADDR + 0x68) + +/* CPLD IRQ line for external uart, external ethernet etc */ +#define EXPIO_PARENT_INT IOMUX_TO_IRQ(MX31_PIN_GPIO1_1) + +#define MXC_EXP_IO_BASE (MXC_BOARD_IRQ_START) +#define MXC_IRQ_TO_EXPIO(irq) ((irq) - MXC_EXP_IO_BASE) + +#define EXPIO_INT_ENET (MXC_EXP_IO_BASE + 0) +#define EXPIO_INT_XUART_A (MXC_EXP_IO_BASE + 1) +#define EXPIO_INT_XUART_B (MXC_EXP_IO_BASE + 2) +#define EXPIO_INT_BUTTON_A (MXC_EXP_IO_BASE + 3) +#define EXPIO_INT_BUTTON_B (MXC_EXP_IO_BASE + 4) + +#define MXC_MAX_EXP_IO_LINES 16 + #endif /* __ASM_ARCH_MXC_BOARD_MX31PDK_H__ */ diff --git a/arch/arm/plat-mxc/include/mach/board-pcm037.h b/arch/arm/plat-mxc/include/mach/board-pcm037.h index 82232ba3c8f..f0a1fa1938a 100644 --- a/arch/arm/plat-mxc/include/mach/board-pcm037.h +++ b/arch/arm/plat-mxc/include/mach/board-pcm037.h @@ -19,7 +19,7 @@ #ifndef __ASM_ARCH_MXC_BOARD_PCM037_H__ #define __ASM_ARCH_MXC_BOARD_PCM037_H__ -/* mandatory for CONFIG_LL_DEBUG */ +/* mandatory for CONFIG_DEBUG_LL */ #define MXC_LL_UART_PADDR UART1_BASE_ADDR #define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) diff --git a/arch/arm/plat-mxc/include/mach/board-pcm038.h b/arch/arm/plat-mxc/include/mach/board-pcm038.h index 750c62afd90..4fcd7499e09 100644 --- a/arch/arm/plat-mxc/include/mach/board-pcm038.h +++ b/arch/arm/plat-mxc/include/mach/board-pcm038.h @@ -19,7 +19,7 @@ #ifndef __ASM_ARCH_MXC_BOARD_PCM038_H__ #define __ASM_ARCH_MXC_BOARD_PCM038_H__ -/* mandatory for CONFIG_LL_DEBUG */ +/* mandatory for CONFIG_DEBUG_LL */ #define MXC_LL_UART_PADDR UART1_BASE_ADDR #define MXC_LL_UART_VADDR (AIPI_BASE_ADDR_VIRT + 0x0A000) diff --git a/arch/arm/mach-imx/include/mach/timex.h b/arch/arm/plat-mxc/include/mach/board-pcm043.h index e22ba789546..15fbdf16abc 100644 --- a/arch/arm/mach-imx/include/mach/timex.h +++ b/arch/arm/plat-mxc/include/mach/board-pcm043.h @@ -1,7 +1,5 @@ /* - * linux/include/asm-arm/imx/timex.h - * - * Copyright (C) 1999 ARM Limited + * Copyright (C) 2008 Sascha Hauer, Pengutronix * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -18,9 +16,12 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#ifndef __ASM_ARCH_TIMEX_H -#define __ASM_ARCH_TIMEX_H +#ifndef __ASM_ARCH_MXC_BOARD_PCM043_H__ +#define __ASM_ARCH_MXC_BOARD_PCM043_H__ + +/* mandatory for CONFIG_LL_DEBUG */ -#define CLOCK_TICK_RATE (16000000) +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) -#endif +#endif /* __ASM_ARCH_MXC_BOARD_PCM043_H__ */ diff --git a/arch/arm/plat-mxc/include/mach/board-qong.h b/arch/arm/plat-mxc/include/mach/board-qong.h index 4ff762dd45c..04033ec637d 100644 --- a/arch/arm/plat-mxc/include/mach/board-qong.h +++ b/arch/arm/plat-mxc/include/mach/board-qong.h @@ -11,7 +11,7 @@ #ifndef __ASM_ARCH_MXC_BOARD_QONG_H__ #define __ASM_ARCH_MXC_BOARD_QONG_H__ -/* mandatory for CONFIG_LL_DEBUG */ +/* mandatory for CONFIG_DEBUG_LL */ #define MXC_LL_UART_PADDR UART1_BASE_ADDR #define MXC_LL_UART_VADDR AIPS1_IO_ADDRESS(UART1_BASE_ADDR) diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h index b2f9b72644d..02c3cd004db 100644 --- a/arch/arm/plat-mxc/include/mach/common.h +++ b/arch/arm/plat-mxc/include/mach/common.h @@ -14,7 +14,11 @@ struct platform_device; struct clk; -extern void mxc_map_io(void); +extern void mx1_map_io(void); +extern void mx21_map_io(void); +extern void mx27_map_io(void); +extern void mx31_map_io(void); +extern void mx35_map_io(void); extern void mxc_init_irq(void); extern void mxc_timer_init(struct clk *timer_clk); extern int mx1_clocks_init(unsigned long fref); diff --git a/arch/arm/plat-mxc/include/mach/debug-macro.S b/arch/arm/plat-mxc/include/mach/debug-macro.S index 4f773148bc2..e6b841b15e3 100644 --- a/arch/arm/plat-mxc/include/mach/debug-macro.S +++ b/arch/arm/plat-mxc/include/mach/debug-macro.S @@ -25,6 +25,9 @@ #ifdef CONFIG_MACH_MX27ADS #include <mach/board-mx27ads.h> #endif +#ifdef CONFIG_MACH_MX21ADS +#include <mach/board-mx21ads.h> +#endif #ifdef CONFIG_MACH_PCM038 #include <mach/board-pcm038.h> #endif @@ -34,6 +37,12 @@ #ifdef CONFIG_MACH_QONG #include <mach/board-qong.h> #endif +#ifdef CONFIG_MACH_PCM043 +#include <mach/board-pcm043.h> +#endif +#ifdef CONFIG_MACH_MX27_3DS +#include <mach/board-mx27pdk.h> +#endif .macro addruart,rx mrc p15, 0, \rx, c1, c0 tst \rx, #1 @ MMU enabled? diff --git a/arch/arm/plat-mxc/include/mach/gpio.h b/arch/arm/plat-mxc/include/mach/gpio.h index ea509f1090f..894d2f87c85 100644 --- a/arch/arm/plat-mxc/include/mach/gpio.h +++ b/arch/arm/plat-mxc/include/mach/gpio.h @@ -35,6 +35,7 @@ struct mxc_gpio_port { int irq; int virtual_irq_start; struct gpio_chip chip; + u32 both_edges; }; int mxc_gpio_init(struct mxc_gpio_port*, int); diff --git a/arch/arm/plat-mxc/include/mach/imx-uart.h b/arch/arm/plat-mxc/include/mach/imx-uart.h index 599217b2e13..90af4d9bc19 100644 --- a/arch/arm/plat-mxc/include/mach/imx-uart.h +++ b/arch/arm/plat-mxc/include/mach/imx-uart.h @@ -23,7 +23,7 @@ struct imxuart_platform_data { int (*init)(struct platform_device *pdev); - int (*exit)(struct platform_device *pdev); + void (*exit)(struct platform_device *pdev); unsigned int flags; }; diff --git a/arch/arm/plat-mxc/include/mach/imxfb.h b/arch/arm/plat-mxc/include/mach/imxfb.h index 762a7b0430e..9f0101157ec 100644 --- a/arch/arm/plat-mxc/include/mach/imxfb.h +++ b/arch/arm/plat-mxc/include/mach/imxfb.h @@ -76,8 +76,8 @@ struct imx_fb_platform_data { u_char * fixed_screen_cpu; dma_addr_t fixed_screen_dma; - int (*init)(struct platform_device*); - int (*exit)(struct platform_device*); + int (*init)(struct platform_device *); + void (*exit)(struct platform_device *); void (*lcd_power)(int); void (*backlight_power)(int); diff --git a/arch/arm/plat-mxc/include/mach/iomux-mx3.h b/arch/arm/plat-mxc/include/mach/iomux-mx3.h index 57e927a1fd3..27f8d1b2bc6 100644 --- a/arch/arm/plat-mxc/include/mach/iomux-mx3.h +++ b/arch/arm/plat-mxc/include/mach/iomux-mx3.h @@ -114,7 +114,7 @@ enum iomux_gp_func { * - setups the iomux according to the configuration * - if the pin is configured as a GPIO, we claim it throug kernel gpiolib */ -int mxc_iomux_setup_pin(const unsigned int pin, const char *label); +int mxc_iomux_alloc_pin(const unsigned int pin, const char *label); /* * setups mutliple pins * convenient way to call the above function with tables @@ -633,6 +633,40 @@ enum iomux_pins { #define MX31_PIN_USBOTG_DIR__USBOTG_DIR IOMUX_MODE(MX31_PIN_USBOTG_DIR, IOMUX_CONFIG_FUNC) #define MX31_PIN_USBOTG_NXT__USBOTG_NXT IOMUX_MODE(MX31_PIN_USBOTG_NXT, IOMUX_CONFIG_FUNC) #define MX31_PIN_USBOTG_STP__USBOTG_STP IOMUX_MODE(MX31_PIN_USBOTG_STP, IOMUX_CONFIG_FUNC) +#define MX31_PIN_USB_OC__GPIO1_30 IOMUX_MODE(MX31_PIN_USB_OC, IOMUX_CONFIG_GPIO) +#define MX31_PIN_I2C_DAT__I2C1_SDA IOMUX_MODE(MX31_PIN_I2C_DAT, IOMUX_CONFIG_FUNC) +#define MX31_PIN_I2C_CLK__I2C1_SCL IOMUX_MODE(MX31_PIN_I2C_CLK, IOMUX_CONFIG_FUNC) +#define MX31_PIN_DCD_DTE1__I2C2_SDA IOMUX_MODE(MX31_PIN_DCD_DTE1, IOMUX_CONFIG_ALT2) +#define MX31_PIN_RI_DTE1__I2C2_SCL IOMUX_MODE(MX31_PIN_RI_DTE1, IOMUX_CONFIG_ALT2) +#define MX31_PIN_ATA_CS0__GPIO3_26 IOMUX_MODE(MX31_PIN_ATA_CS0, IOMUX_CONFIG_GPIO) +#define MX31_PIN_ATA_CS1__GPIO3_27 IOMUX_MODE(MX31_PIN_ATA_CS1, IOMUX_CONFIG_GPIO) +#define MX31_PIN_PC_PWRON__SD2_DATA3 IOMUX_MODE(MX31_PIN_PC_PWRON, IOMUX_CONFIG_ALT1) +#define MX31_PIN_PC_VS1__SD2_DATA2 IOMUX_MODE(MX31_PIN_PC_VS1, IOMUX_CONFIG_ALT1) +#define MX31_PIN_PC_READY__SD2_DATA1 IOMUX_MODE(MX31_PIN_PC_READY, IOMUX_CONFIG_ALT1) +#define MX31_PIN_PC_WAIT_B__SD2_DATA0 IOMUX_MODE(MX31_PIN_PC_WAIT_B, IOMUX_CONFIG_ALT1) +#define MX31_PIN_PC_CD2_B__SD2_CLK IOMUX_MODE(MX31_PIN_PC_CD2_B, IOMUX_CONFIG_ALT1) +#define MX31_PIN_PC_CD1_B__SD2_CMD IOMUX_MODE(MX31_PIN_PC_CD1_B, IOMUX_CONFIG_ALT1) +#define MX31_PIN_ATA_DIOR__GPIO3_28 IOMUX_MODE(MX31_PIN_ATA_DIOR, IOMUX_CONFIG_GPIO) +#define MX31_PIN_ATA_DIOW__GPIO3_29 IOMUX_MODE(MX31_PIN_ATA_DIOW, IOMUX_CONFIG_GPIO) +#define MX31_PIN_CSI_D4__CSI_D4 IOMUX_MODE(MX31_PIN_CSI_D4, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D5__CSI_D5 IOMUX_MODE(MX31_PIN_CSI_D5, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D6__CSI_D6 IOMUX_MODE(MX31_PIN_CSI_D6, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D7__CSI_D7 IOMUX_MODE(MX31_PIN_CSI_D7, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D8__CSI_D8 IOMUX_MODE(MX31_PIN_CSI_D8, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D9__CSI_D9 IOMUX_MODE(MX31_PIN_CSI_D9, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D10__CSI_D10 IOMUX_MODE(MX31_PIN_CSI_D10, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D11__CSI_D11 IOMUX_MODE(MX31_PIN_CSI_D11, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D12__CSI_D12 IOMUX_MODE(MX31_PIN_CSI_D12, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D13__CSI_D13 IOMUX_MODE(MX31_PIN_CSI_D13, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D14__CSI_D14 IOMUX_MODE(MX31_PIN_CSI_D14, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_D15__CSI_D15 IOMUX_MODE(MX31_PIN_CSI_D15, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_HSYNC__CSI_HSYNC IOMUX_MODE(MX31_PIN_CSI_HSYNC, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_MCLK__CSI_MCLK IOMUX_MODE(MX31_PIN_CSI_MCLK, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_PIXCLK__CSI_PIXCLK IOMUX_MODE(MX31_PIN_CSI_PIXCLK, IOMUX_CONFIG_FUNC) +#define MX31_PIN_CSI_VSYNC__CSI_VSYNC IOMUX_MODE(MX31_PIN_CSI_VSYNC, IOMUX_CONFIG_FUNC) +#define MX31_PIN_GPIO3_0__GPIO3_0 IOMUX_MODE(MX31_PIN_GPIO3_0, IOMUX_CONFIG_GPIO) +#define MX31_PIN_GPIO3_1__GPIO3_1 IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO) +#define MX31_PIN_TXD2__GPIO1_28 IOMUX_MODE(MX31_PIN_TXD2, IOMUX_CONFIG_GPIO) /*XXX: The SS0, SS1, SS2, SS3 lines of spi3 are multiplexed by cspi2_ss0, cspi2_ss1, cspi1_ss0 * cspi1_ss1*/ diff --git a/arch/arm/plat-mxc/include/mach/iomux-mx35.h b/arch/arm/plat-mxc/include/mach/iomux-mx35.h new file mode 100644 index 00000000000..00b0ac1db22 --- /dev/null +++ b/arch/arm/plat-mxc/include/mach/iomux-mx35.h @@ -0,0 +1,1267 @@ +/* + * Copyright (C, NO_PAD_CTRL) 2009 by Jan Weitzel Phytec Messtechnik GmbH <armlinux@phytec.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option, NO_PAD_CTRL) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef __MACH_IOMUX_MX35_H__ +#define __MACH_IOMUX_MX35_H__ + +#include <mach/iomux-v3.h> + +/* + * The naming convention for the pad modes is MX35_PAD_<padname>__<padmode> + * If <padname> or <padmode> refers to a GPIO, it is named + * GPIO_<unit>_<num> see also iomux-v3.h + */ + +/* PAD MUX ALT INPSE PATH */ +#define MX35_PAD_CAPTURE__GPT_CAPIN1 IOMUX_PAD(0x328, 0x004, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CAPTURE__GPT_CMPOUT2 IOMUX_PAD(0x328, 0x004, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CAPTURE__CSPI2_SS1 IOMUX_PAD(0x328, 0x004, 2, 0x7f4, 0, NO_PAD_CTRL) +#define MX35_PAD_CAPTURE__EPIT1_EPITO IOMUX_PAD(0x328, 0x004, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CAPTURE__CCM_CLK32K IOMUX_PAD(0x328, 0x004, 4, 0x7d0, 0, NO_PAD_CTRL) +#define MX35_PAD_CAPTURE__GPIO1_4 IOMUX_PAD(0x328, 0x004, 5, 0x850, 0, NO_PAD_CTRL) + +#define MX35_PAD_COMPARE__GPT_CMPOUT1 IOMUX_PAD(0x32c, 0x008, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_COMPARE__GPT_CAPIN2 IOMUX_PAD(0x32c, 0x008, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_COMPARE__GPT_CMPOUT3 IOMUX_PAD(0x32c, 0x008, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_COMPARE__EPIT2_EPITO IOMUX_PAD(0x32c, 0x008, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_COMPARE__GPIO1_5 IOMUX_PAD(0x32c, 0x008, 5, 0x854, 0, NO_PAD_CTRL) +#define MX35_PAD_COMPARE__SDMA_EXTDMA_2 IOMUX_PAD(0x32c, 0x008, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_WDOG_RST__WDOG_WDOG_B IOMUX_PAD(0x330, 0x00c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_WDOG_RST__IPU_FLASH_STROBE IOMUX_PAD(0x330, 0x00c, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_WDOG_RST__GPIO1_6 IOMUX_PAD(0x330, 0x00c, 5, 0x858, 0, NO_PAD_CTRL) + +#define MX35_PAD_GPIO1_0__GPIO1_0 IOMUX_PAD(0x334, 0x010, 0, 0x82c, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO1_0__CCM_PMIC_RDY IOMUX_PAD(0x334, 0x010, 1, 0x7d4, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO1_0__OWIRE_LINE IOMUX_PAD(0x334, 0x010, 2, 0x990, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO1_0__SDMA_EXTDMA_0 IOMUX_PAD(0x334, 0x010, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_GPIO1_1__GPIO1_1 IOMUX_PAD(0x338, 0x014, 0, 0x838, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO1_1__PWM_PWMO IOMUX_PAD(0x338, 0x014, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO1_1__CSPI1_SS2 IOMUX_PAD(0x338, 0x014, 3, 0x7d8, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO1_1__SCC_TAMPER_DETECT IOMUX_PAD(0x338, 0x014, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO1_1__SDMA_EXTDMA_1 IOMUX_PAD(0x338, 0x014, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_GPIO2_0__GPIO2_0 IOMUX_PAD(0x33c, 0x018, 0, 0x868, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO2_0__USB_TOP_USBOTG_CLK IOMUX_PAD(0x33c, 0x018, 1, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_GPIO3_0__GPIO3_0 IOMUX_PAD(0x340, 0x01c, 0, 0x8e8, 0, NO_PAD_CTRL) +#define MX35_PAD_GPIO3_0__USB_TOP_USBH2_CLK IOMUX_PAD(0x340, 0x01c, 1, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_RESET_IN_B__CCM_RESET_IN_B IOMUX_PAD(0x344, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_POR_B__CCM_POR_B IOMUX_PAD(0x348, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CLKO__CCM_CLKO IOMUX_PAD(0x34c, 0x020, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CLKO__GPIO1_8 IOMUX_PAD(0x34c, 0x020, 5, 0x860, 0, NO_PAD_CTRL) + +#define MX35_PAD_BOOT_MODE0__CCM_BOOT_MODE_0 IOMUX_PAD(0x350, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_BOOT_MODE1__CCM_BOOT_MODE_1 IOMUX_PAD(0x354, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CLK_MODE0__CCM_CLK_MODE_0 IOMUX_PAD(0x358, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CLK_MODE1__CCM_CLK_MODE_1 IOMUX_PAD(0x35c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_POWER_FAIL__CCM_DSM_WAKEUP_INT_26 IOMUX_PAD(0x360, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_VSTBY__CCM_VSTBY IOMUX_PAD(0x364, 0x024, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_VSTBY__GPIO1_7 IOMUX_PAD(0x364, 0x024, 5, 0x85c, 0, NO_PAD_CTRL) + +#define MX35_PAD_A0__EMI_EIM_DA_L_0 IOMUX_PAD(0x368, 0x028, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A1__EMI_EIM_DA_L_1 IOMUX_PAD(0x36c, 0x02c, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A2__EMI_EIM_DA_L_2 IOMUX_PAD(0x370, 0x030, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A3__EMI_EIM_DA_L_3 IOMUX_PAD(0x374, 0x034, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A4__EMI_EIM_DA_L_4 IOMUX_PAD(0x378, 0x038, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A5__EMI_EIM_DA_L_5 IOMUX_PAD(0x37c, 0x03c, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A6__EMI_EIM_DA_L_6 IOMUX_PAD(0x380, 0x040, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A7__EMI_EIM_DA_L_7 IOMUX_PAD(0x384, 0x044, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A8__EMI_EIM_DA_H_8 IOMUX_PAD(0x388, 0x048, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A9__EMI_EIM_DA_H_9 IOMUX_PAD(0x38c, 0x04c, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A10__EMI_EIM_DA_H_10 IOMUX_PAD(0x390, 0x050, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_MA10__EMI_MA10 IOMUX_PAD(0x394, 0x054, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A11__EMI_EIM_DA_H_11 IOMUX_PAD(0x398, 0x058, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A12__EMI_EIM_DA_H_12 IOMUX_PAD(0x39c, 0x05c, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A13__EMI_EIM_DA_H_13 IOMUX_PAD(0x3a0, 0x060, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A14__EMI_EIM_DA_H2_14 IOMUX_PAD(0x3a4, 0x064, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A15__EMI_EIM_DA_H2_15 IOMUX_PAD(0x3a8, 0x068, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A16__EMI_EIM_A_16 IOMUX_PAD(0x3ac, 0x06c, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A17__EMI_EIM_A_17 IOMUX_PAD(0x3b0, 0x070, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A18__EMI_EIM_A_18 IOMUX_PAD(0x3b4, 0x074, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A19__EMI_EIM_A_19 IOMUX_PAD(0x3b8, 0x078, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A20__EMI_EIM_A_20 IOMUX_PAD(0x3bc, 0x07c, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A21__EMI_EIM_A_21 IOMUX_PAD(0x3c0, 0x080, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A22__EMI_EIM_A_22 IOMUX_PAD(0x3c4, 0x084, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A23__EMI_EIM_A_23 IOMUX_PAD(0x3c8, 0x088, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A24__EMI_EIM_A_24 IOMUX_PAD(0x3cc, 0x08c, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_A25__EMI_EIM_A_25 IOMUX_PAD(0x3d0, 0x090, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDBA1__EMI_EIM_SDBA1 IOMUX_PAD(0x3d4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDBA0__EMI_EIM_SDBA0 IOMUX_PAD(0x3d8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD0__EMI_DRAM_D_0 IOMUX_PAD(0x3dc, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD1__EMI_DRAM_D_1 IOMUX_PAD(0x3e0, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD2__EMI_DRAM_D_2 IOMUX_PAD(0x3e4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD3__EMI_DRAM_D_3 IOMUX_PAD(0x3e8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD4__EMI_DRAM_D_4 IOMUX_PAD(0x3ec, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD5__EMI_DRAM_D_5 IOMUX_PAD(0x3f0, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD6__EMI_DRAM_D_6 IOMUX_PAD(0x3f4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD7__EMI_DRAM_D_7 IOMUX_PAD(0x3f8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD8__EMI_DRAM_D_8 IOMUX_PAD(0x3fc, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD9__EMI_DRAM_D_9 IOMUX_PAD(0x400, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD10__EMI_DRAM_D_10 IOMUX_PAD(0x404, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD11__EMI_DRAM_D_11 IOMUX_PAD(0x408, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD12__EMI_DRAM_D_12 IOMUX_PAD(0x40c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD13__EMI_DRAM_D_13 IOMUX_PAD(0x410, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD14__EMI_DRAM_D_14 IOMUX_PAD(0x414, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD15__EMI_DRAM_D_15 IOMUX_PAD(0x418, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD16__EMI_DRAM_D_16 IOMUX_PAD(0x41c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD17__EMI_DRAM_D_17 IOMUX_PAD(0x420, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD18__EMI_DRAM_D_18 IOMUX_PAD(0x424, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD19__EMI_DRAM_D_19 IOMUX_PAD(0x428, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD20__EMI_DRAM_D_20 IOMUX_PAD(0x42c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD21__EMI_DRAM_D_21 IOMUX_PAD(0x430, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD22__EMI_DRAM_D_22 IOMUX_PAD(0x434, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD23__EMI_DRAM_D_23 IOMUX_PAD(0x438, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD24__EMI_DRAM_D_24 IOMUX_PAD(0x43c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD25__EMI_DRAM_D_25 IOMUX_PAD(0x440, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD26__EMI_DRAM_D_26 IOMUX_PAD(0x444, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD27__EMI_DRAM_D_27 IOMUX_PAD(0x448, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD28__EMI_DRAM_D_28 IOMUX_PAD(0x44c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD29__EMI_DRAM_D_29 IOMUX_PAD(0x450, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD30__EMI_DRAM_D_30 IOMUX_PAD(0x454, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD31__EMI_DRAM_D_31 IOMUX_PAD(0x458, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_DQM0__EMI_DRAM_DQM_0 IOMUX_PAD(0x45c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_DQM1__EMI_DRAM_DQM_1 IOMUX_PAD(0x460, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_DQM2__EMI_DRAM_DQM_2 IOMUX_PAD(0x464, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_DQM3__EMI_DRAM_DQM_3 IOMUX_PAD(0x468, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_EB0__EMI_EIM_EB0_B IOMUX_PAD(0x46c, 0x094, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_EB1__EMI_EIM_EB1_B IOMUX_PAD(0x470, 0x098, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_OE__EMI_EIM_OE IOMUX_PAD(0x474, 0x09c, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CS0__EMI_EIM_CS0 IOMUX_PAD(0x478, 0x0a0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CS1__EMI_EIM_CS1 IOMUX_PAD(0x47c, 0x0a4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CS1__EMI_NANDF_CE3 IOMUX_PAD(0x47c, 0x0a4, 3, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CS2__EMI_EIM_CS2 IOMUX_PAD(0x480, 0x0a8, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CS3__EMI_EIM_CS3 IOMUX_PAD(0x484, 0x0ac, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CS4__EMI_EIM_CS4 IOMUX_PAD(0x488, 0x0b0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CS4__EMI_DTACK_B IOMUX_PAD(0x488, 0x0b0, 1, 0x800, 0, NO_PAD_CTRL) +#define MX35_PAD_CS4__EMI_NANDF_CE1 IOMUX_PAD(0x488, 0x0b0, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CS4__GPIO1_20 IOMUX_PAD(0x488, 0x0b0, 5, 0x83c, 0, NO_PAD_CTRL) + +#define MX35_PAD_CS5__EMI_EIM_CS5 IOMUX_PAD(0x48c, 0x0b4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CS5__CSPI2_SS2 IOMUX_PAD(0x48c, 0x0b4, 1, 0x7f8, 0, NO_PAD_CTRL) +#define MX35_PAD_CS5__CSPI1_SS2 IOMUX_PAD(0x48c, 0x0b4, 2, 0x7d8, 1, NO_PAD_CTRL) +#define MX35_PAD_CS5__EMI_NANDF_CE2 IOMUX_PAD(0x48c, 0x0b4, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CS5__GPIO1_21 IOMUX_PAD(0x48c, 0x0b4, 5, 0x840, 0, NO_PAD_CTRL) + +#define MX35_PAD_NF_CE0__EMI_NANDF_CE0 IOMUX_PAD(0x490, 0x0b8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NF_CE0__GPIO1_22 IOMUX_PAD(0x490, 0x0b8, 5, 0x844, 0, NO_PAD_CTRL) + +#define MX35_PAD_ECB__EMI_EIM_ECB IOMUX_PAD(0x494, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LBA__EMI_EIM_LBA IOMUX_PAD(0x498, 0x0bc, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_BCLK__EMI_EIM_BCLK IOMUX_PAD(0x49c, 0x0c0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_RW__EMI_EIM_RW IOMUX_PAD(0x4a0, 0x0c4, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_RAS__EMI_DRAM_RAS IOMUX_PAD(0x4a4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CAS__EMI_DRAM_CAS IOMUX_PAD(0x4a8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDWE__EMI_DRAM_SDWE IOMUX_PAD(0x4ac, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDCKE0__EMI_DRAM_SDCKE_0 IOMUX_PAD(0x4b0, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDCKE1__EMI_DRAM_SDCKE_1 IOMUX_PAD(0x4b4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDCLK__EMI_DRAM_SDCLK IOMUX_PAD(0x4b8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDQS0__EMI_DRAM_SDQS_0 IOMUX_PAD(0x4bc, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDQS1__EMI_DRAM_SDQS_1 IOMUX_PAD(0x4c0, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDQS2__EMI_DRAM_SDQS_2 IOMUX_PAD(0x4c4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SDQS3__EMI_DRAM_SDQS_3 IOMUX_PAD(0x4c8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_NFWE_B__EMI_NANDF_WE_B IOMUX_PAD(0x4cc, 0x0c8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFWE_B__USB_TOP_USBH2_DATA_3 IOMUX_PAD(0x4cc, 0x0c8, 1, 0x9d8, 0, NO_PAD_CTRL) +#define MX35_PAD_NFWE_B__IPU_DISPB_D0_VSYNC IOMUX_PAD(0x4cc, 0x0c8, 2, 0x924, 0, NO_PAD_CTRL) +#define MX35_PAD_NFWE_B__GPIO2_18 IOMUX_PAD(0x4cc, 0x0c8, 5, 0x88c, 0, NO_PAD_CTRL) +#define MX35_PAD_NFWE_B__ARM11P_TOP_TRACE_0 IOMUX_PAD(0x4cc, 0x0c8, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_NFRE_B__EMI_NANDF_RE_B IOMUX_PAD(0x4d0, 0x0cc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFRE_B__USB_TOP_USBH2_DIR IOMUX_PAD(0x4d0, 0x0cc, 1, 0x9ec, 0, NO_PAD_CTRL) +#define MX35_PAD_NFRE_B__IPU_DISPB_BCLK IOMUX_PAD(0x4d0, 0x0cc, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFRE_B__GPIO2_19 IOMUX_PAD(0x4d0, 0x0cc, 5, 0x890, 0, NO_PAD_CTRL) +#define MX35_PAD_NFRE_B__ARM11P_TOP_TRACE_1 IOMUX_PAD(0x4d0, 0x0cc, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_NFALE__EMI_NANDF_ALE IOMUX_PAD(0x4d4, 0x0d0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFALE__USB_TOP_USBH2_STP IOMUX_PAD(0x4d4, 0x0d0, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFALE__IPU_DISPB_CS0 IOMUX_PAD(0x4d4, 0x0d0, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFALE__GPIO2_20 IOMUX_PAD(0x4d4, 0x0d0, 5, 0x898, 0, NO_PAD_CTRL) +#define MX35_PAD_NFALE__ARM11P_TOP_TRACE_2 IOMUX_PAD(0x4d4, 0x0d0, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_NFCLE__EMI_NANDF_CLE IOMUX_PAD(0x4d8, 0x0d4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFCLE__USB_TOP_USBH2_NXT IOMUX_PAD(0x4d8, 0x0d4, 1, 0x9f0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFCLE__IPU_DISPB_PAR_RS IOMUX_PAD(0x4d8, 0x0d4, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFCLE__GPIO2_21 IOMUX_PAD(0x4d8, 0x0d4, 5, 0x89c, 0, NO_PAD_CTRL) +#define MX35_PAD_NFCLE__ARM11P_TOP_TRACE_3 IOMUX_PAD(0x4d8, 0x0d4, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_NFWP_B__EMI_NANDF_WP_B IOMUX_PAD(0x4dc, 0x0d8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFWP_B__USB_TOP_USBH2_DATA_7 IOMUX_PAD(0x4dc, 0x0d8, 1, 0x9e8, 0, NO_PAD_CTRL) +#define MX35_PAD_NFWP_B__IPU_DISPB_WR IOMUX_PAD(0x4dc, 0x0d8, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFWP_B__GPIO2_22 IOMUX_PAD(0x4dc, 0x0d8, 5, 0x8a0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFWP_B__ARM11P_TOP_TRCTL IOMUX_PAD(0x4dc, 0x0d8, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_NFRB__EMI_NANDF_RB IOMUX_PAD(0x4e0, 0x0dc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFRB__IPU_DISPB_RD IOMUX_PAD(0x4e0, 0x0dc, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_NFRB__GPIO2_23 IOMUX_PAD(0x4e0, 0x0dc, 5, 0x8a4, 0, NO_PAD_CTRL) +#define MX35_PAD_NFRB__ARM11P_TOP_TRCLK IOMUX_PAD(0x4e0, 0x0dc, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D15__EMI_EIM_D_15 IOMUX_PAD(0x4e4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D14__EMI_EIM_D_14 IOMUX_PAD(0x4e8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D13__EMI_EIM_D_13 IOMUX_PAD(0x4ec, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D12__EMI_EIM_D_12 IOMUX_PAD(0x4f0, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D11__EMI_EIM_D_11 IOMUX_PAD(0x4f4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D10__EMI_EIM_D_10 IOMUX_PAD(0x4f8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D9__EMI_EIM_D_9 IOMUX_PAD(0x4fc, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D8__EMI_EIM_D_8 IOMUX_PAD(0x500, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D7__EMI_EIM_D_7 IOMUX_PAD(0x504, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D6__EMI_EIM_D_6 IOMUX_PAD(0x508, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D5__EMI_EIM_D_5 IOMUX_PAD(0x50c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D4__EMI_EIM_D_4 IOMUX_PAD(0x510, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D3__EMI_EIM_D_3 IOMUX_PAD(0x514, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D2__EMI_EIM_D_2 IOMUX_PAD(0x518, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D1__EMI_EIM_D_1 IOMUX_PAD(0x51c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D0__EMI_EIM_D_0 IOMUX_PAD(0x520, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_D8__IPU_CSI_D_8 IOMUX_PAD(0x524, 0x0e0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D8__KPP_COL_0 IOMUX_PAD(0x524, 0x0e0, 1, 0x950, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D8__GPIO1_20 IOMUX_PAD(0x524, 0x0e0, 5, 0x83c, 1, NO_PAD_CTRL) +#define MX35_PAD_CSI_D8__ARM11P_TOP_EVNTBUS_13 IOMUX_PAD(0x524, 0x0e0, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_D9__IPU_CSI_D_9 IOMUX_PAD(0x528, 0x0e4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D9__KPP_COL_1 IOMUX_PAD(0x528, 0x0e4, 1, 0x954, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D9__GPIO1_21 IOMUX_PAD(0x528, 0x0e4, 5, 0x840, 1, NO_PAD_CTRL) +#define MX35_PAD_CSI_D9__ARM11P_TOP_EVNTBUS_14 IOMUX_PAD(0x528, 0x0e4, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_D10__IPU_CSI_D_10 IOMUX_PAD(0x52c, 0x0e8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D10__KPP_COL_2 IOMUX_PAD(0x52c, 0x0e8, 1, 0x958, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D10__GPIO1_22 IOMUX_PAD(0x52c, 0x0e8, 5, 0x844, 1, NO_PAD_CTRL) +#define MX35_PAD_CSI_D10__ARM11P_TOP_EVNTBUS_15 IOMUX_PAD(0x52c, 0x0e8, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_D11__IPU_CSI_D_11 IOMUX_PAD(0x530, 0x0ec, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D11__KPP_COL_3 IOMUX_PAD(0x530, 0x0ec, 1, 0x95c, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D11__GPIO1_23 IOMUX_PAD(0x530, 0x0ec, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_D12__IPU_CSI_D_12 IOMUX_PAD(0x534, 0x0f0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D12__KPP_ROW_0 IOMUX_PAD(0x534, 0x0f0, 1, 0x970, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D12__GPIO1_24 IOMUX_PAD(0x534, 0x0f0, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_D13__IPU_CSI_D_13 IOMUX_PAD(0x538, 0x0f4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D13__KPP_ROW_1 IOMUX_PAD(0x538, 0x0f4, 1, 0x974, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D13__GPIO1_25 IOMUX_PAD(0x538, 0x0f4, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_D14__IPU_CSI_D_14 IOMUX_PAD(0x53c, 0x0f8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D14__KPP_ROW_2 IOMUX_PAD(0x53c, 0x0f8, 1, 0x978, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D14__GPIO1_26 IOMUX_PAD(0x53c, 0x0f8, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_D15__IPU_CSI_D_15 IOMUX_PAD(0x540, 0x0fc, 0, 0x97c, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D15__KPP_ROW_3 IOMUX_PAD(0x540, 0x0fc, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_D15__GPIO1_27 IOMUX_PAD(0x540, 0x0fc, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_MCLK__IPU_CSI_MCLK IOMUX_PAD(0x544, 0x100, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_MCLK__GPIO1_28 IOMUX_PAD(0x544, 0x100, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_VSYNC__IPU_CSI_VSYNC IOMUX_PAD(0x548, 0x104, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_VSYNC__GPIO1_29 IOMUX_PAD(0x548, 0x104, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_HSYNC__IPU_CSI_HSYNC IOMUX_PAD(0x54c, 0x108, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_HSYNC__GPIO1_30 IOMUX_PAD(0x54c, 0x108, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSI_PIXCLK__IPU_CSI_PIXCLK IOMUX_PAD(0x550, 0x10c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSI_PIXCLK__GPIO1_31 IOMUX_PAD(0x550, 0x10c, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_I2C1_CLK__I2C1_SCL IOMUX_PAD(0x554, 0x110, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C1_CLK__GPIO2_24 IOMUX_PAD(0x554, 0x110, 5, 0x8a8, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C1_CLK__CCM_USB_BYP_CLK IOMUX_PAD(0x554, 0x110, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_I2C1_DAT__I2C1_SDA IOMUX_PAD(0x558, 0x114, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C1_DAT__GPIO2_25 IOMUX_PAD(0x558, 0x114, 5, 0x8ac, 0, NO_PAD_CTRL) + +#define MX35_PAD_I2C2_CLK__I2C2_SCL IOMUX_PAD(0x55c, 0x118, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C2_CLK__CAN1_TXCAN IOMUX_PAD(0x55c, 0x118, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C2_CLK__USB_TOP_USBH2_PWR IOMUX_PAD(0x55c, 0x118, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C2_CLK__GPIO2_26 IOMUX_PAD(0x55c, 0x118, 5, 0x8b0, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C2_CLK__SDMA_DEBUG_BUS_DEVICE_2 IOMUX_PAD(0x55c, 0x118, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_I2C2_DAT__I2C2_SDA IOMUX_PAD(0x560, 0x11c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C2_DAT__CAN1_RXCAN IOMUX_PAD(0x560, 0x11c, 1, 0x7c8, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C2_DAT__USB_TOP_USBH2_OC IOMUX_PAD(0x560, 0x11c, 2, 0x9f4, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C2_DAT__GPIO2_27 IOMUX_PAD(0x560, 0x11c, 5, 0x8b4, 0, NO_PAD_CTRL) +#define MX35_PAD_I2C2_DAT__SDMA_DEBUG_BUS_DEVICE_3 IOMUX_PAD(0x560, 0x11c, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_STXD4__AUDMUX_AUD4_TXD IOMUX_PAD(0x564, 0x120, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_STXD4__GPIO2_28 IOMUX_PAD(0x564, 0x120, 5, 0x8b8, 0, NO_PAD_CTRL) +#define MX35_PAD_STXD4__ARM11P_TOP_ARM_COREASID0 IOMUX_PAD(0x564, 0x120, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SRXD4__AUDMUX_AUD4_RXD IOMUX_PAD(0x568, 0x124, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SRXD4__GPIO2_29 IOMUX_PAD(0x568, 0x124, 5, 0x8bc, 0, NO_PAD_CTRL) +#define MX35_PAD_SRXD4__ARM11P_TOP_ARM_COREASID1 IOMUX_PAD(0x568, 0x124, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SCK4__AUDMUX_AUD4_TXC IOMUX_PAD(0x56c, 0x128, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SCK4__GPIO2_30 IOMUX_PAD(0x56c, 0x128, 5, 0x8c4, 0, NO_PAD_CTRL) +#define MX35_PAD_SCK4__ARM11P_TOP_ARM_COREASID2 IOMUX_PAD(0x56c, 0x128, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS IOMUX_PAD(0x570, 0x12c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_STXFS4__GPIO2_31 IOMUX_PAD(0x570, 0x12c, 5, 0x8c8, 0, NO_PAD_CTRL) +#define MX35_PAD_STXFS4__ARM11P_TOP_ARM_COREASID3 IOMUX_PAD(0x570, 0x12c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_STXD5__AUDMUX_AUD5_TXD IOMUX_PAD(0x574, 0x130, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_STXD5__SPDIF_SPDIF_OUT1 IOMUX_PAD(0x574, 0x130, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_STXD5__CSPI2_MOSI IOMUX_PAD(0x574, 0x130, 2, 0x7ec, 0, NO_PAD_CTRL) +#define MX35_PAD_STXD5__GPIO1_0 IOMUX_PAD(0x574, 0x130, 5, 0x82c, 1, NO_PAD_CTRL) +#define MX35_PAD_STXD5__ARM11P_TOP_ARM_COREASID4 IOMUX_PAD(0x574, 0x130, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SRXD5__AUDMUX_AUD5_RXD IOMUX_PAD(0x578, 0x134, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SRXD5__SPDIF_SPDIF_IN1 IOMUX_PAD(0x578, 0x134, 1, 0x998, 0, NO_PAD_CTRL) +#define MX35_PAD_SRXD5__CSPI2_MISO IOMUX_PAD(0x578, 0x134, 2, 0x7e8, 0, NO_PAD_CTRL) +#define MX35_PAD_SRXD5__GPIO1_1 IOMUX_PAD(0x578, 0x134, 5, 0x838, 1, NO_PAD_CTRL) +#define MX35_PAD_SRXD5__ARM11P_TOP_ARM_COREASID5 IOMUX_PAD(0x578, 0x134, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SCK5__AUDMUX_AUD5_TXC IOMUX_PAD(0x57c, 0x138, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SCK5__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x57c, 0x138, 1, 0x994, 0, NO_PAD_CTRL) +#define MX35_PAD_SCK5__CSPI2_SCLK IOMUX_PAD(0x57c, 0x138, 2, 0x7e0, 0, NO_PAD_CTRL) +#define MX35_PAD_SCK5__GPIO1_2 IOMUX_PAD(0x57c, 0x138, 5, 0x848, 0, NO_PAD_CTRL) +#define MX35_PAD_SCK5__ARM11P_TOP_ARM_COREASID6 IOMUX_PAD(0x57c, 0x138, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_STXFS5__AUDMUX_AUD5_TXFS IOMUX_PAD(0x580, 0x13c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_STXFS5__CSPI2_RDY IOMUX_PAD(0x580, 0x13c, 2, 0x7e4, 0, NO_PAD_CTRL) +#define MX35_PAD_STXFS5__GPIO1_3 IOMUX_PAD(0x580, 0x13c, 5, 0x84c, 0, NO_PAD_CTRL) +#define MX35_PAD_STXFS5__ARM11P_TOP_ARM_COREASID7 IOMUX_PAD(0x580, 0x13c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SCKR__ESAI_SCKR IOMUX_PAD(0x584, 0x140, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SCKR__GPIO1_4 IOMUX_PAD(0x584, 0x140, 5, 0x850, 1, NO_PAD_CTRL) +#define MX35_PAD_SCKR__ARM11P_TOP_EVNTBUS_10 IOMUX_PAD(0x584, 0x140, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FSR__ESAI_FSR IOMUX_PAD(0x588, 0x144, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FSR__GPIO1_5 IOMUX_PAD(0x588, 0x144, 5, 0x854, 1, NO_PAD_CTRL) +#define MX35_PAD_FSR__ARM11P_TOP_EVNTBUS_11 IOMUX_PAD(0x588, 0x144, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_HCKR__ESAI_HCKR IOMUX_PAD(0x58c, 0x148, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_HCKR__AUDMUX_AUD5_RXFS IOMUX_PAD(0x58c, 0x148, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_HCKR__CSPI2_SS0 IOMUX_PAD(0x58c, 0x148, 2, 0x7f0, 0, NO_PAD_CTRL) +#define MX35_PAD_HCKR__IPU_FLASH_STROBE IOMUX_PAD(0x58c, 0x148, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_HCKR__GPIO1_6 IOMUX_PAD(0x58c, 0x148, 5, 0x858, 1, NO_PAD_CTRL) +#define MX35_PAD_HCKR__ARM11P_TOP_EVNTBUS_12 IOMUX_PAD(0x58c, 0x148, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SCKT__ESAI_SCKT IOMUX_PAD(0x590, 0x14c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SCKT__GPIO1_7 IOMUX_PAD(0x590, 0x14c, 5, 0x85c, 1, NO_PAD_CTRL) +#define MX35_PAD_SCKT__IPU_CSI_D_0 IOMUX_PAD(0x590, 0x14c, 6, 0x930, 0, NO_PAD_CTRL) +#define MX35_PAD_SCKT__KPP_ROW_2 IOMUX_PAD(0x590, 0x14c, 7, 0x978, 1, NO_PAD_CTRL) + +#define MX35_PAD_FST__ESAI_FST IOMUX_PAD(0x594, 0x150, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FST__GPIO1_8 IOMUX_PAD(0x594, 0x150, 5, 0x860, 1, NO_PAD_CTRL) +#define MX35_PAD_FST__IPU_CSI_D_1 IOMUX_PAD(0x594, 0x150, 6, 0x934, 0, NO_PAD_CTRL) +#define MX35_PAD_FST__KPP_ROW_3 IOMUX_PAD(0x594, 0x150, 7, 0x97c, 1, NO_PAD_CTRL) + +#define MX35_PAD_HCKT__ESAI_HCKT IOMUX_PAD(0x598, 0x154, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_HCKT__AUDMUX_AUD5_RXC IOMUX_PAD(0x598, 0x154, 1, 0x7a8, 0, NO_PAD_CTRL) +#define MX35_PAD_HCKT__GPIO1_9 IOMUX_PAD(0x598, 0x154, 5, 0x864, 0, NO_PAD_CTRL) +#define MX35_PAD_HCKT__IPU_CSI_D_2 IOMUX_PAD(0x598, 0x154, 6, 0x938, 0, NO_PAD_CTRL) +#define MX35_PAD_HCKT__KPP_COL_3 IOMUX_PAD(0x598, 0x154, 7, 0x95c, 1, NO_PAD_CTRL) + +#define MX35_PAD_TX5_RX0__ESAI_TX5_RX0 IOMUX_PAD(0x59c, 0x158, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX5_RX0__AUDMUX_AUD4_RXC IOMUX_PAD(0x59c, 0x158, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX5_RX0__CSPI2_SS2 IOMUX_PAD(0x59c, 0x158, 2, 0x7f8, 1, NO_PAD_CTRL) +#define MX35_PAD_TX5_RX0__CAN2_TXCAN IOMUX_PAD(0x59c, 0x158, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX5_RX0__UART2_DTR IOMUX_PAD(0x59c, 0x158, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX5_RX0__GPIO1_10 IOMUX_PAD(0x59c, 0x158, 5, 0x830, 0, NO_PAD_CTRL) +#define MX35_PAD_TX5_RX0__EMI_M3IF_CHOSEN_MASTER_0 IOMUX_PAD(0x59c, 0x158, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_TX4_RX1__ESAI_TX4_RX1 IOMUX_PAD(0x5a0, 0x15c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX4_RX1__AUDMUX_AUD4_RXFS IOMUX_PAD(0x5a0, 0x15c, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX4_RX1__CSPI2_SS3 IOMUX_PAD(0x5a0, 0x15c, 2, 0x7fc, 0, NO_PAD_CTRL) +#define MX35_PAD_TX4_RX1__CAN2_RXCAN IOMUX_PAD(0x5a0, 0x15c, 3, 0x7cc, 0, NO_PAD_CTRL) +#define MX35_PAD_TX4_RX1__UART2_DSR IOMUX_PAD(0x5a0, 0x15c, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX4_RX1__GPIO1_11 IOMUX_PAD(0x5a0, 0x15c, 5, 0x834, 0, NO_PAD_CTRL) +#define MX35_PAD_TX4_RX1__IPU_CSI_D_3 IOMUX_PAD(0x5a0, 0x15c, 6, 0x93c, 0, NO_PAD_CTRL) +#define MX35_PAD_TX4_RX1__KPP_ROW_0 IOMUX_PAD(0x5a0, 0x15c, 7, 0x970, 1, NO_PAD_CTRL) + +#define MX35_PAD_TX3_RX2__ESAI_TX3_RX2 IOMUX_PAD(0x5a4, 0x160, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX3_RX2__I2C3_SCL IOMUX_PAD(0x5a4, 0x160, 1, 0x91c, 0, NO_PAD_CTRL) +#define MX35_PAD_TX3_RX2__EMI_NANDF_CE1 IOMUX_PAD(0x5a4, 0x160, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX3_RX2__GPIO1_12 IOMUX_PAD(0x5a4, 0x160, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX3_RX2__IPU_CSI_D_4 IOMUX_PAD(0x5a4, 0x160, 6, 0x940, 0, NO_PAD_CTRL) +#define MX35_PAD_TX3_RX2__KPP_ROW_1 IOMUX_PAD(0x5a4, 0x160, 7, 0x974, 1, NO_PAD_CTRL) + +#define MX35_PAD_TX2_RX3__ESAI_TX2_RX3 IOMUX_PAD(0x5a8, 0x164, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX2_RX3__I2C3_SDA IOMUX_PAD(0x5a8, 0x164, 1, 0x920, 0, NO_PAD_CTRL) +#define MX35_PAD_TX2_RX3__EMI_NANDF_CE2 IOMUX_PAD(0x5a8, 0x164, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX2_RX3__GPIO1_13 IOMUX_PAD(0x5a8, 0x164, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX2_RX3__IPU_CSI_D_5 IOMUX_PAD(0x5a8, 0x164, 6, 0x944, 0, NO_PAD_CTRL) +#define MX35_PAD_TX2_RX3__KPP_COL_0 IOMUX_PAD(0x5a8, 0x164, 7, 0x950, 1, NO_PAD_CTRL) + +#define MX35_PAD_TX1__ESAI_TX1 IOMUX_PAD(0x5ac, 0x168, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX1__CCM_PMIC_RDY IOMUX_PAD(0x5ac, 0x168, 1, 0x7d4, 1, NO_PAD_CTRL) +#define MX35_PAD_TX1__CSPI1_SS2 IOMUX_PAD(0x5ac, 0x168, 2, 0x7d8, 2, NO_PAD_CTRL) +#define MX35_PAD_TX1__EMI_NANDF_CE3 IOMUX_PAD(0x5ac, 0x168, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX1__UART2_RI IOMUX_PAD(0x5ac, 0x168, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX1__GPIO1_14 IOMUX_PAD(0x5ac, 0x168, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX1__IPU_CSI_D_6 IOMUX_PAD(0x5ac, 0x168, 6, 0x948, 0, NO_PAD_CTRL) +#define MX35_PAD_TX1__KPP_COL_1 IOMUX_PAD(0x5ac, 0x168, 7, 0x954, 1, NO_PAD_CTRL) + +#define MX35_PAD_TX0__ESAI_TX0 IOMUX_PAD(0x5b0, 0x16c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX0__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x5b0, 0x16c, 1, 0x994, 1, NO_PAD_CTRL) +#define MX35_PAD_TX0__CSPI1_SS3 IOMUX_PAD(0x5b0, 0x16c, 2, 0x7dc, 0, NO_PAD_CTRL) +#define MX35_PAD_TX0__EMI_DTACK_B IOMUX_PAD(0x5b0, 0x16c, 3, 0x800, 1, NO_PAD_CTRL) +#define MX35_PAD_TX0__UART2_DCD IOMUX_PAD(0x5b0, 0x16c, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX0__GPIO1_15 IOMUX_PAD(0x5b0, 0x16c, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TX0__IPU_CSI_D_7 IOMUX_PAD(0x5b0, 0x16c, 6, 0x94c, 0, NO_PAD_CTRL) +#define MX35_PAD_TX0__KPP_COL_2 IOMUX_PAD(0x5b0, 0x16c, 7, 0x958, 1, NO_PAD_CTRL) + +#define MX35_PAD_CSPI1_MOSI__CSPI1_MOSI IOMUX_PAD(0x5b4, 0x170, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_MOSI__GPIO1_16 IOMUX_PAD(0x5b4, 0x170, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_MOSI__ECT_CTI_TRIG_OUT1_2 IOMUX_PAD(0x5b4, 0x170, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSPI1_MISO__CSPI1_MISO IOMUX_PAD(0x5b8, 0x174, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_MISO__GPIO1_17 IOMUX_PAD(0x5b8, 0x174, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_MISO__ECT_CTI_TRIG_OUT1_3 IOMUX_PAD(0x5b8, 0x174, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSPI1_SS0__CSPI1_SS0 IOMUX_PAD(0x5bc, 0x178, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS0__OWIRE_LINE IOMUX_PAD(0x5bc, 0x178, 1, 0x990, 1, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS0__CSPI2_SS3 IOMUX_PAD(0x5bc, 0x178, 2, 0x7fc, 1, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS0__GPIO1_18 IOMUX_PAD(0x5bc, 0x178, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS0__ECT_CTI_TRIG_OUT1_4 IOMUX_PAD(0x5bc, 0x178, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSPI1_SS1__CSPI1_SS1 IOMUX_PAD(0x5c0, 0x17c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS1__PWM_PWMO IOMUX_PAD(0x5c0, 0x17c, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS1__CCM_CLK32K IOMUX_PAD(0x5c0, 0x17c, 2, 0x7d0, 1, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS1__GPIO1_19 IOMUX_PAD(0x5c0, 0x17c, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS1__IPU_DIAGB_29 IOMUX_PAD(0x5c0, 0x17c, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SS1__ECT_CTI_TRIG_OUT1_5 IOMUX_PAD(0x5c0, 0x17c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSPI1_SCLK__CSPI1_SCLK IOMUX_PAD(0x5c4, 0x180, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SCLK__GPIO3_4 IOMUX_PAD(0x5c4, 0x180, 5, 0x904, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SCLK__IPU_DIAGB_30 IOMUX_PAD(0x5c4, 0x180, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SCLK__EMI_M3IF_CHOSEN_MASTER_1 IOMUX_PAD(0x5c4, 0x180, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CSPI1_SPI_RDY__CSPI1_RDY IOMUX_PAD(0x5c8, 0x184, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SPI_RDY__GPIO3_5 IOMUX_PAD(0x5c8, 0x184, 5, 0x908, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SPI_RDY__IPU_DIAGB_31 IOMUX_PAD(0x5c8, 0x184, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CSPI1_SPI_RDY__EMI_M3IF_CHOSEN_MASTER_2 IOMUX_PAD(0x5c8, 0x184, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_RXD1__UART1_RXD_MUX IOMUX_PAD(0x5cc, 0x188, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_RXD1__CSPI2_MOSI IOMUX_PAD(0x5cc, 0x188, 1, 0x7ec, 1, NO_PAD_CTRL) +#define MX35_PAD_RXD1__KPP_COL_4 IOMUX_PAD(0x5cc, 0x188, 4, 0x960, 0, NO_PAD_CTRL) +#define MX35_PAD_RXD1__GPIO3_6 IOMUX_PAD(0x5cc, 0x188, 5, 0x90c, 0, NO_PAD_CTRL) +#define MX35_PAD_RXD1__ARM11P_TOP_EVNTBUS_16 IOMUX_PAD(0x5cc, 0x188, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_TXD1__UART1_TXD_MUX IOMUX_PAD(0x5d0, 0x18c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TXD1__CSPI2_MISO IOMUX_PAD(0x5d0, 0x18c, 1, 0x7e8, 1, NO_PAD_CTRL) +#define MX35_PAD_TXD1__KPP_COL_5 IOMUX_PAD(0x5d0, 0x18c, 4, 0x964, 0, NO_PAD_CTRL) +#define MX35_PAD_TXD1__GPIO3_7 IOMUX_PAD(0x5d0, 0x18c, 5, 0x910, 0, NO_PAD_CTRL) +#define MX35_PAD_TXD1__ARM11P_TOP_EVNTBUS_17 IOMUX_PAD(0x5d0, 0x18c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_RTS1__UART1_RTS IOMUX_PAD(0x5d4, 0x190, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_RTS1__CSPI2_SCLK IOMUX_PAD(0x5d4, 0x190, 1, 0x7e0, 1, NO_PAD_CTRL) +#define MX35_PAD_RTS1__I2C3_SCL IOMUX_PAD(0x5d4, 0x190, 2, 0x91c, 1, NO_PAD_CTRL) +#define MX35_PAD_RTS1__IPU_CSI_D_0 IOMUX_PAD(0x5d4, 0x190, 3, 0x930, 1, NO_PAD_CTRL) +#define MX35_PAD_RTS1__KPP_COL_6 IOMUX_PAD(0x5d4, 0x190, 4, 0x968, 0, NO_PAD_CTRL) +#define MX35_PAD_RTS1__GPIO3_8 IOMUX_PAD(0x5d4, 0x190, 5, 0x914, 0, NO_PAD_CTRL) +#define MX35_PAD_RTS1__EMI_NANDF_CE1 IOMUX_PAD(0x5d4, 0x190, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_RTS1__ARM11P_TOP_EVNTBUS_18 IOMUX_PAD(0x5d4, 0x190, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CTS1__UART1_CTS IOMUX_PAD(0x5d8, 0x194, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS1__CSPI2_RDY IOMUX_PAD(0x5d8, 0x194, 1, 0x7e4, 1, NO_PAD_CTRL) +#define MX35_PAD_CTS1__I2C3_SDA IOMUX_PAD(0x5d8, 0x194, 2, 0x920, 1, NO_PAD_CTRL) +#define MX35_PAD_CTS1__IPU_CSI_D_1 IOMUX_PAD(0x5d8, 0x194, 3, 0x934, 1, NO_PAD_CTRL) +#define MX35_PAD_CTS1__KPP_COL_7 IOMUX_PAD(0x5d8, 0x194, 4, 0x96c, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS1__GPIO3_9 IOMUX_PAD(0x5d8, 0x194, 5, 0x918, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS1__EMI_NANDF_CE2 IOMUX_PAD(0x5d8, 0x194, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS1__ARM11P_TOP_EVNTBUS_19 IOMUX_PAD(0x5d8, 0x194, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_RXD2__UART2_RXD_MUX IOMUX_PAD(0x5dc, 0x198, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_RXD2__KPP_ROW_4 IOMUX_PAD(0x5dc, 0x198, 4, 0x980, 0, NO_PAD_CTRL) +#define MX35_PAD_RXD2__GPIO3_10 IOMUX_PAD(0x5dc, 0x198, 5, 0x8ec, 0, NO_PAD_CTRL) + +#define MX35_PAD_TXD2__UART2_TXD_MUX IOMUX_PAD(0x5e0, 0x19c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_TXD2__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x5e0, 0x19c, 1, 0x994, 2, NO_PAD_CTRL) +#define MX35_PAD_TXD2__KPP_ROW_5 IOMUX_PAD(0x5e0, 0x19c, 4, 0x984, 0, NO_PAD_CTRL) +#define MX35_PAD_TXD2__GPIO3_11 IOMUX_PAD(0x5e0, 0x19c, 5, 0x8f0, 0, NO_PAD_CTRL) + +#define MX35_PAD_RTS2__UART2_RTS IOMUX_PAD(0x5e4, 0x1a0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_RTS2__SPDIF_SPDIF_IN1 IOMUX_PAD(0x5e4, 0x1a0, 1, 0x998, 1, NO_PAD_CTRL) +#define MX35_PAD_RTS2__CAN2_RXCAN IOMUX_PAD(0x5e4, 0x1a0, 2, 0x7cc, 1, NO_PAD_CTRL) +#define MX35_PAD_RTS2__IPU_CSI_D_2 IOMUX_PAD(0x5e4, 0x1a0, 3, 0x938, 1, NO_PAD_CTRL) +#define MX35_PAD_RTS2__KPP_ROW_6 IOMUX_PAD(0x5e4, 0x1a0, 4, 0x988, 0, NO_PAD_CTRL) +#define MX35_PAD_RTS2__GPIO3_12 IOMUX_PAD(0x5e4, 0x1a0, 5, 0x8f4, 0, NO_PAD_CTRL) +#define MX35_PAD_RTS2__AUDMUX_AUD5_RXC IOMUX_PAD(0x5e4, 0x1a0, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_RTS2__UART3_RXD_MUX IOMUX_PAD(0x5e4, 0x1a0, 7, 0x9a0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CTS2__UART2_CTS IOMUX_PAD(0x5e8, 0x1a4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS2__SPDIF_SPDIF_OUT1 IOMUX_PAD(0x5e8, 0x1a4, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS2__CAN2_TXCAN IOMUX_PAD(0x5e8, 0x1a4, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS2__IPU_CSI_D_3 IOMUX_PAD(0x5e8, 0x1a4, 3, 0x93c, 1, NO_PAD_CTRL) +#define MX35_PAD_CTS2__KPP_ROW_7 IOMUX_PAD(0x5e8, 0x1a4, 4, 0x98c, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS2__GPIO3_13 IOMUX_PAD(0x5e8, 0x1a4, 5, 0x8f8, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS2__AUDMUX_AUD5_RXFS IOMUX_PAD(0x5e8, 0x1a4, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CTS2__UART3_TXD_MUX IOMUX_PAD(0x5e8, 0x1a4, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_RTCK__ARM11P_TOP_RTCK IOMUX_PAD(0x5ec, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_TCK__SJC_TCK IOMUX_PAD(0x5f0, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_TMS__SJC_TMS IOMUX_PAD(0x5f4, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_TDI__SJC_TDI IOMUX_PAD(0x5f8, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_TDO__SJC_TDO IOMUX_PAD(0x5fc, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_TRSTB__SJC_TRSTB IOMUX_PAD(0x600, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_DE_B__SJC_DE_B IOMUX_PAD(0x604, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SJC_MOD__SJC_MOD IOMUX_PAD(0x608, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR IOMUX_PAD(0x60c, 0x1a8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_USBOTG_PWR__USB_TOP_USBH2_PWR IOMUX_PAD(0x60c, 0x1a8, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_USBOTG_PWR__GPIO3_14 IOMUX_PAD(0x60c, 0x1a8, 5, 0x8fc, 0, NO_PAD_CTRL) + +#define MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC IOMUX_PAD(0x610, 0x1ac, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_USBOTG_OC__USB_TOP_USBH2_OC IOMUX_PAD(0x610, 0x1ac, 1, 0x9f4, 1, NO_PAD_CTRL) +#define MX35_PAD_USBOTG_OC__GPIO3_15 IOMUX_PAD(0x610, 0x1ac, 5, 0x900, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD0__IPU_DISPB_DAT_0 IOMUX_PAD(0x614, 0x1b0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD0__GPIO2_0 IOMUX_PAD(0x614, 0x1b0, 5, 0x868, 1, NO_PAD_CTRL) +#define MX35_PAD_LD0__SDMA_SDMA_DEBUG_PC_0 IOMUX_PAD(0x614, 0x1b0, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD1__IPU_DISPB_DAT_1 IOMUX_PAD(0x618, 0x1b4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD1__GPIO2_1 IOMUX_PAD(0x618, 0x1b4, 5, 0x894, 0, NO_PAD_CTRL) +#define MX35_PAD_LD1__SDMA_SDMA_DEBUG_PC_1 IOMUX_PAD(0x618, 0x1b4, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD2__IPU_DISPB_DAT_2 IOMUX_PAD(0x61c, 0x1b8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD2__GPIO2_2 IOMUX_PAD(0x61c, 0x1b8, 5, 0x8c0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD2__SDMA_SDMA_DEBUG_PC_2 IOMUX_PAD(0x61c, 0x1b8, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD3__IPU_DISPB_DAT_3 IOMUX_PAD(0x620, 0x1bc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD3__GPIO2_3 IOMUX_PAD(0x620, 0x1bc, 5, 0x8cc, 0, NO_PAD_CTRL) +#define MX35_PAD_LD3__SDMA_SDMA_DEBUG_PC_3 IOMUX_PAD(0x620, 0x1bc, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD4__IPU_DISPB_DAT_4 IOMUX_PAD(0x624, 0x1c0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD4__GPIO2_4 IOMUX_PAD(0x624, 0x1c0, 5, 0x8d0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD4__SDMA_SDMA_DEBUG_PC_4 IOMUX_PAD(0x624, 0x1c0, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD5__IPU_DISPB_DAT_5 IOMUX_PAD(0x628, 0x1c4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD5__GPIO2_5 IOMUX_PAD(0x628, 0x1c4, 5, 0x8d4, 0, NO_PAD_CTRL) +#define MX35_PAD_LD5__SDMA_SDMA_DEBUG_PC_5 IOMUX_PAD(0x628, 0x1c4, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD6__IPU_DISPB_DAT_6 IOMUX_PAD(0x62c, 0x1c8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD6__GPIO2_6 IOMUX_PAD(0x62c, 0x1c8, 5, 0x8d8, 0, NO_PAD_CTRL) +#define MX35_PAD_LD6__SDMA_SDMA_DEBUG_PC_6 IOMUX_PAD(0x62c, 0x1c8, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD7__IPU_DISPB_DAT_7 IOMUX_PAD(0x630, 0x1cc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD7__GPIO2_7 IOMUX_PAD(0x630, 0x1cc, 5, 0x8dc, 0, NO_PAD_CTRL) +#define MX35_PAD_LD7__SDMA_SDMA_DEBUG_PC_7 IOMUX_PAD(0x630, 0x1cc, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD8__IPU_DISPB_DAT_8 IOMUX_PAD(0x634, 0x1d0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD8__GPIO2_8 IOMUX_PAD(0x634, 0x1d0, 5, 0x8e0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD8__SDMA_SDMA_DEBUG_PC_8 IOMUX_PAD(0x634, 0x1d0, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD9__IPU_DISPB_DAT_9 IOMUX_PAD(0x638, 0x1d4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD9__GPIO2_9 IOMUX_PAD(0x638, 0x1d4, 5, 0x8e4 0, NO_PAD_CTRL) +#define MX35_PAD_LD9__SDMA_SDMA_DEBUG_PC_9 IOMUX_PAD(0x638, 0x1d4, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD10__IPU_DISPB_DAT_10 IOMUX_PAD(0x63c, 0x1d8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD10__GPIO2_10 IOMUX_PAD(0x63c, 0x1d8, 5, 0x86c, 0, NO_PAD_CTRL) +#define MX35_PAD_LD10__SDMA_SDMA_DEBUG_PC_10 IOMUX_PAD(0x63c, 0x1d8, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD11__IPU_DISPB_DAT_11 IOMUX_PAD(0x640, 0x1dc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD11__GPIO2_11 IOMUX_PAD(0x640, 0x1dc, 5, 0x870, 0, NO_PAD_CTRL) +#define MX35_PAD_LD11__SDMA_SDMA_DEBUG_PC_11 IOMUX_PAD(0x640, 0x1dc, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD11__ARM11P_TOP_TRACE_4 IOMUX_PAD(0x640, 0x1dc, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD12__IPU_DISPB_DAT_12 IOMUX_PAD(0x644, 0x1e0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD12__GPIO2_12 IOMUX_PAD(0x644, 0x1e0, 5, 0x874, 0, NO_PAD_CTRL) +#define MX35_PAD_LD12__SDMA_SDMA_DEBUG_PC_12 IOMUX_PAD(0x644, 0x1e0, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD12__ARM11P_TOP_TRACE_5 IOMUX_PAD(0x644, 0x1e0, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD13__IPU_DISPB_DAT_13 IOMUX_PAD(0x648, 0x1e4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD13__GPIO2_13 IOMUX_PAD(0x648, 0x1e4, 5, 0x878, 0, NO_PAD_CTRL) +#define MX35_PAD_LD13__SDMA_SDMA_DEBUG_PC_13 IOMUX_PAD(0x648, 0x1e4, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD13__ARM11P_TOP_TRACE_6 IOMUX_PAD(0x648, 0x1e4, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD14__IPU_DISPB_DAT_14 IOMUX_PAD(0x64c, 0x1e8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD14__GPIO2_14 IOMUX_PAD(0x64c, 0x1e8, 5, 0x87c, 0, NO_PAD_CTRL) +#define MX35_PAD_LD14__SDMA_SDMA_DEBUG_EVENT_CHANNEL_0 IOMUX_PAD(0x64c, 0x1e8, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD14__ARM11P_TOP_TRACE_7 IOMUX_PAD(0x64c, 0x1e8, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD15__IPU_DISPB_DAT_15 IOMUX_PAD(0x650, 0x1ec, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD15__GPIO2_15 IOMUX_PAD(0x650, 0x1ec, 5, 0x880, 0, NO_PAD_CTRL) +#define MX35_PAD_LD15__SDMA_SDMA_DEBUG_EVENT_CHANNEL_1 IOMUX_PAD(0x650, 0x1ec, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD15__ARM11P_TOP_TRACE_8 IOMUX_PAD(0x650, 0x1ec, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD16__IPU_DISPB_DAT_16 IOMUX_PAD(0x654, 0x1f0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD16__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x654, 0x1f0, 2, 0x928, 0, NO_PAD_CTRL) +#define MX35_PAD_LD16__GPIO2_16 IOMUX_PAD(0x654, 0x1f0, 5, 0x884, 0, NO_PAD_CTRL) +#define MX35_PAD_LD16__SDMA_SDMA_DEBUG_EVENT_CHANNEL_2 IOMUX_PAD(0x654, 0x1f0, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD16__ARM11P_TOP_TRACE_9 IOMUX_PAD(0x654, 0x1f0, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD17__IPU_DISPB_DAT_17 IOMUX_PAD(0x658, 0x1f4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD17__IPU_DISPB_CS2 IOMUX_PAD(0x658, 0x1f4, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD17__GPIO2_17 IOMUX_PAD(0x658, 0x1f4, 5, 0x888, 0, NO_PAD_CTRL) +#define MX35_PAD_LD17__SDMA_SDMA_DEBUG_EVENT_CHANNEL_3 IOMUX_PAD(0x658, 0x1f4, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD17__ARM11P_TOP_TRACE_10 IOMUX_PAD(0x658, 0x1f4, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD18__IPU_DISPB_DAT_18 IOMUX_PAD(0x65c, 0x1f8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD18__IPU_DISPB_D0_VSYNC IOMUX_PAD(0x65c, 0x1f8, 1, 0x924, 1, NO_PAD_CTRL) +#define MX35_PAD_LD18__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x65c, 0x1f8, 2, 0x928, 1, NO_PAD_CTRL) +#define MX35_PAD_LD18__ESDHC3_CMD IOMUX_PAD(0x65c, 0x1f8, 3, 0x818, 0, NO_PAD_CTRL) +#define MX35_PAD_LD18__USB_TOP_USBOTG_DATA_3 IOMUX_PAD(0x65c, 0x1f8, 4, 0x9b0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD18__GPIO3_24 IOMUX_PAD(0x65c, 0x1f8, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD18__SDMA_SDMA_DEBUG_EVENT_CHANNEL_4 IOMUX_PAD(0x65c, 0x1f8, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD18__ARM11P_TOP_TRACE_11 IOMUX_PAD(0x65c, 0x1f8, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD19__IPU_DISPB_DAT_19 IOMUX_PAD(0x660, 0x1fc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD19__IPU_DISPB_BCLK IOMUX_PAD(0x660, 0x1fc, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD19__IPU_DISPB_CS1 IOMUX_PAD(0x660, 0x1fc, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD19__ESDHC3_CLK IOMUX_PAD(0x660, 0x1fc, 3, 0x814, 0, NO_PAD_CTRL) +#define MX35_PAD_LD19__USB_TOP_USBOTG_DIR IOMUX_PAD(0x660, 0x1fc, 4, 0x9c4, 0, NO_PAD_CTRL) +#define MX35_PAD_LD19__GPIO3_25 IOMUX_PAD(0x660, 0x1fc, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD19__SDMA_SDMA_DEBUG_EVENT_CHANNEL_5 IOMUX_PAD(0x660, 0x1fc, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD19__ARM11P_TOP_TRACE_12 IOMUX_PAD(0x660, 0x1fc, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD20__IPU_DISPB_DAT_20 IOMUX_PAD(0x664, 0x200, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD20__IPU_DISPB_CS0 IOMUX_PAD(0x664, 0x200, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD20__IPU_DISPB_SD_CLK IOMUX_PAD(0x664, 0x200, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD20__ESDHC3_DAT0 IOMUX_PAD(0x664, 0x200, 3, 0x81c, 0, NO_PAD_CTRL) +#define MX35_PAD_LD20__GPIO3_26 IOMUX_PAD(0x664, 0x200, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD20__SDMA_SDMA_DEBUG_CORE_STATUS_3 IOMUX_PAD(0x664, 0x200, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD20__ARM11P_TOP_TRACE_13 IOMUX_PAD(0x664, 0x200, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD21__IPU_DISPB_DAT_21 IOMUX_PAD(0x668, 0x204, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD21__IPU_DISPB_PAR_RS IOMUX_PAD(0x668, 0x204, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD21__IPU_DISPB_SER_RS IOMUX_PAD(0x668, 0x204, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD21__ESDHC3_DAT1 IOMUX_PAD(0x668, 0x204, 3, 0x820, 0, NO_PAD_CTRL) +#define MX35_PAD_LD21__USB_TOP_USBOTG_STP IOMUX_PAD(0x668, 0x204, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD21__GPIO3_27 IOMUX_PAD(0x668, 0x204, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD21__SDMA_DEBUG_EVENT_CHANNEL_SEL IOMUX_PAD(0x668, 0x204, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD21__ARM11P_TOP_TRACE_14 IOMUX_PAD(0x668, 0x204, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD22__IPU_DISPB_DAT_22 IOMUX_PAD(0x66c, 0x208, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD22__IPU_DISPB_WR IOMUX_PAD(0x66c, 0x208, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD22__IPU_DISPB_SD_D_I IOMUX_PAD(0x66c, 0x208, 2, 0x92c, 0, NO_PAD_CTRL) +#define MX35_PAD_LD22__ESDHC3_DAT2 IOMUX_PAD(0x66c, 0x208, 3, 0x824, 0, NO_PAD_CTRL) +#define MX35_PAD_LD22__USB_TOP_USBOTG_NXT IOMUX_PAD(0x66c, 0x208, 4, 0x9c8, 0, NO_PAD_CTRL) +#define MX35_PAD_LD22__GPIO3_28 IOMUX_PAD(0x66c, 0x208, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD22__SDMA_DEBUG_BUS_ERROR IOMUX_PAD(0x66c, 0x208, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD22__ARM11P_TOP_TRCTL IOMUX_PAD(0x66c, 0x208, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_LD23__IPU_DISPB_DAT_23 IOMUX_PAD(0x670, 0x20c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD23__IPU_DISPB_RD IOMUX_PAD(0x670, 0x20c, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD23__IPU_DISPB_SD_D_IO IOMUX_PAD(0x670, 0x20c, 2, 0x92c, 1, NO_PAD_CTRL) +#define MX35_PAD_LD23__ESDHC3_DAT3 IOMUX_PAD(0x670, 0x20c, 3, 0x828, 0, NO_PAD_CTRL) +#define MX35_PAD_LD23__USB_TOP_USBOTG_DATA_7 IOMUX_PAD(0x670, 0x20c, 4, 0x9c0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD23__GPIO3_29 IOMUX_PAD(0x670, 0x20c, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD23__SDMA_DEBUG_MATCHED_DMBUS IOMUX_PAD(0x670, 0x20c, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_LD23__ARM11P_TOP_TRCLK IOMUX_PAD(0x670, 0x20c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC IOMUX_PAD(0x674, 0x210, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_HSYNC__IPU_DISPB_SD_D_IO IOMUX_PAD(0x674, 0x210, 2, 0x92c, 2, NO_PAD_CTRL) +#define MX35_PAD_D3_HSYNC__GPIO3_30 IOMUX_PAD(0x674, 0x210, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_HSYNC__SDMA_DEBUG_RTBUFFER_WRITE IOMUX_PAD(0x674, 0x210, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_HSYNC__ARM11P_TOP_TRACE_15 IOMUX_PAD(0x674, 0x210, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK IOMUX_PAD(0x678, 0x214, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_FPSHIFT__IPU_DISPB_SD_CLK IOMUX_PAD(0x678, 0x214, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_FPSHIFT__GPIO3_31 IOMUX_PAD(0x678, 0x214, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_FPSHIFT__SDMA_SDMA_DEBUG_CORE_STATUS_0 IOMUX_PAD(0x678, 0x214, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_FPSHIFT__ARM11P_TOP_TRACE_16 IOMUX_PAD(0x678, 0x214, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY IOMUX_PAD(0x67c, 0x218, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_DRDY__IPU_DISPB_SD_D_O IOMUX_PAD(0x67c, 0x218, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_DRDY__GPIO1_0 IOMUX_PAD(0x67c, 0x218, 5, 0x82c, 2, NO_PAD_CTRL) +#define MX35_PAD_D3_DRDY__SDMA_SDMA_DEBUG_CORE_STATUS_1 IOMUX_PAD(0x67c, 0x218, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_DRDY__ARM11P_TOP_TRACE_17 IOMUX_PAD(0x67c, 0x218, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_CONTRAST__IPU_DISPB_CONTR IOMUX_PAD(0x680, 0x21c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CONTRAST__GPIO1_1 IOMUX_PAD(0x680, 0x21c, 5, 0x838, 2, NO_PAD_CTRL) +#define MX35_PAD_CONTRAST__SDMA_SDMA_DEBUG_CORE_STATUS_2 IOMUX_PAD(0x680, 0x21c, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_CONTRAST__ARM11P_TOP_TRACE_18 IOMUX_PAD(0x680, 0x21c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC IOMUX_PAD(0x684, 0x220, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_VSYNC__IPU_DISPB_CS1 IOMUX_PAD(0x684, 0x220, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_VSYNC__GPIO1_2 IOMUX_PAD(0x684, 0x220, 5, 0x848, 1, NO_PAD_CTRL) +#define MX35_PAD_D3_VSYNC__SDMA_DEBUG_YIELD IOMUX_PAD(0x684, 0x220, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_VSYNC__ARM11P_TOP_TRACE_19 IOMUX_PAD(0x684, 0x220, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D3_REV__IPU_DISPB_D3_REV IOMUX_PAD(0x688, 0x224, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_REV__IPU_DISPB_SER_RS IOMUX_PAD(0x688, 0x224, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_REV__GPIO1_3 IOMUX_PAD(0x688, 0x224, 5, 0x84c, 1, NO_PAD_CTRL) +#define MX35_PAD_D3_REV__SDMA_DEBUG_BUS_RWB IOMUX_PAD(0x688, 0x224, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_REV__ARM11P_TOP_TRACE_20 IOMUX_PAD(0x688, 0x224, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS IOMUX_PAD(0x68c, 0x228, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_CLS__IPU_DISPB_CS2 IOMUX_PAD(0x68c, 0x228, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_CLS__GPIO1_4 IOMUX_PAD(0x68c, 0x228, 5, 0x850, 2, NO_PAD_CTRL) +#define MX35_PAD_D3_CLS__SDMA_DEBUG_BUS_DEVICE_0 IOMUX_PAD(0x68c, 0x228, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_CLS__ARM11P_TOP_TRACE_21 IOMUX_PAD(0x68c, 0x228, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_D3_SPL__IPU_DISPB_D3_SPL IOMUX_PAD(0x690, 0x22c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_SPL__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x690, 0x22c, 2, 0x928, 2, NO_PAD_CTRL) +#define MX35_PAD_D3_SPL__GPIO1_5 IOMUX_PAD(0x690, 0x22c, 5, 0x854, 2, NO_PAD_CTRL) +#define MX35_PAD_D3_SPL__SDMA_DEBUG_BUS_DEVICE_1 IOMUX_PAD(0x690, 0x22c, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_D3_SPL__ARM11P_TOP_TRACE_22 IOMUX_PAD(0x690, 0x22c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD1_CMD__ESDHC1_CMD IOMUX_PAD(0x694, 0x230, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_CMD__MSHC_SCLK IOMUX_PAD(0x694, 0x230, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_CMD__IPU_DISPB_D0_VSYNC IOMUX_PAD(0x694, 0x230, 3, 0x924, 2, NO_PAD_CTRL) +#define MX35_PAD_SD1_CMD__USB_TOP_USBOTG_DATA_4 IOMUX_PAD(0x694, 0x230, 4, 0x9b4, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_CMD__GPIO1_6 IOMUX_PAD(0x694, 0x230, 5, 0x858, 2, NO_PAD_CTRL) +#define MX35_PAD_SD1_CMD__ARM11P_TOP_TRCTL IOMUX_PAD(0x694, 0x230, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD1_CLK__ESDHC1_CLK IOMUX_PAD(0x698, 0x234, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_CLK__MSHC_BS IOMUX_PAD(0x698, 0x234, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_CLK__IPU_DISPB_BCLK IOMUX_PAD(0x698, 0x234, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_CLK__USB_TOP_USBOTG_DATA_5 IOMUX_PAD(0x698, 0x234, 4, 0x9b8, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_CLK__GPIO1_7 IOMUX_PAD(0x698, 0x234, 5, 0x85c, 2, NO_PAD_CTRL) +#define MX35_PAD_SD1_CLK__ARM11P_TOP_TRCLK IOMUX_PAD(0x698, 0x234, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD1_DATA0__ESDHC1_DAT0 IOMUX_PAD(0x69c, 0x238, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA0__MSHC_DATA_0 IOMUX_PAD(0x69c, 0x238, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA0__IPU_DISPB_CS0 IOMUX_PAD(0x69c, 0x238, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA0__USB_TOP_USBOTG_DATA_6 IOMUX_PAD(0x69c, 0x238, 4, 0x9bc, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA0__GPIO1_8 IOMUX_PAD(0x69c, 0x238, 5, 0x860, 2, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA0__ARM11P_TOP_TRACE_23 IOMUX_PAD(0x69c, 0x238, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD1_DATA1__ESDHC1_DAT1 IOMUX_PAD(0x6a0, 0x23c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA1__MSHC_DATA_1 IOMUX_PAD(0x6a0, 0x23c, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA1__IPU_DISPB_PAR_RS IOMUX_PAD(0x6a0, 0x23c, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA1__USB_TOP_USBOTG_DATA_0 IOMUX_PAD(0x6a0, 0x23c, 4, 0x9a4, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA1__GPIO1_9 IOMUX_PAD(0x6a0, 0x23c, 5, 0x864, 1, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA1__ARM11P_TOP_TRACE_24 IOMUX_PAD(0x6a0, 0x23c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD1_DATA2__ESDHC1_DAT2 IOMUX_PAD(0x6a4, 0x240, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA2__MSHC_DATA_2 IOMUX_PAD(0x6a4, 0x240, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA2__IPU_DISPB_WR IOMUX_PAD(0x6a4, 0x240, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA2__USB_TOP_USBOTG_DATA_1 IOMUX_PAD(0x6a4, 0x240, 4, 0x9a8, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA2__GPIO1_10 IOMUX_PAD(0x6a4, 0x240, 5, 0x830, 1, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA2__ARM11P_TOP_TRACE_25 IOMUX_PAD(0x6a4, 0x240, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD1_DATA3__ESDHC1_DAT3 IOMUX_PAD(0x6a8, 0x244, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA3__MSHC_DATA_3 IOMUX_PAD(0x6a8, 0x244, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA3__IPU_DISPB_RD IOMUX_PAD(0x6a8, 0x244, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA3__USB_TOP_USBOTG_DATA_2 IOMUX_PAD(0x6a8, 0x244, 4, 0x9ac, 0, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA3__GPIO1_11 IOMUX_PAD(0x6a8, 0x244, 5, 0x834, 1, NO_PAD_CTRL) +#define MX35_PAD_SD1_DATA3__ARM11P_TOP_TRACE_26 IOMUX_PAD(0x6a8, 0x244, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD2_CMD__ESDHC2_CMD IOMUX_PAD(0x6ac, 0x248, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_CMD__I2C3_SCL IOMUX_PAD(0x6ac, 0x248, 1, 0x91c, 2, NO_PAD_CTRL) +#define MX35_PAD_SD2_CMD__ESDHC1_DAT4 IOMUX_PAD(0x6ac, 0x248, 2, 0x804, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_CMD__IPU_CSI_D_2 IOMUX_PAD(0x6ac, 0x248, 3, 0x938, 2, NO_PAD_CTRL) +#define MX35_PAD_SD2_CMD__USB_TOP_USBH2_DATA_4 IOMUX_PAD(0x6ac, 0x248, 4, 0x9dc, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_CMD__GPIO2_0 IOMUX_PAD(0x6ac, 0x248, 5, 0x868, 2, NO_PAD_CTRL) +#define MX35_PAD_SD2_CMD__SPDIF_SPDIF_OUT1 IOMUX_PAD(0x6ac, 0x248, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_CMD__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x6ac, 0x248, 7, 0x928, 3, NO_PAD_CTRL) + +#define MX35_PAD_SD2_CLK__ESDHC2_CLK IOMUX_PAD(0x6b0, 0x24c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_CLK__I2C3_SDA IOMUX_PAD(0x6b0, 0x24c, 1, 0x920, 2, NO_PAD_CTRL) +#define MX35_PAD_SD2_CLK__ESDHC1_DAT5 IOMUX_PAD(0x6b0, 0x24c, 2, 0x808, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_CLK__IPU_CSI_D_3 IOMUX_PAD(0x6b0, 0x24c, 3, 0x93c, 2, NO_PAD_CTRL) +#define MX35_PAD_SD2_CLK__USB_TOP_USBH2_DATA_5 IOMUX_PAD(0x6b0, 0x24c, 4, 0x9e0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_CLK__GPIO2_1 IOMUX_PAD(0x6b0, 0x24c, 5, 0x894, 1, NO_PAD_CTRL) +#define MX35_PAD_SD2_CLK__SPDIF_SPDIF_IN1 IOMUX_PAD(0x6b0, 0x24c, 6, 0x998, 2, NO_PAD_CTRL) +#define MX35_PAD_SD2_CLK__IPU_DISPB_CS2 IOMUX_PAD(0x6b0, 0x24c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_SD2_DATA0__ESDHC2_DAT0 IOMUX_PAD(0x6b4, 0x250, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA0__UART3_RXD_MUX IOMUX_PAD(0x6b4, 0x250, 1, 0x9a0, 1, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA0__ESDHC1_DAT6 IOMUX_PAD(0x6b4, 0x250, 2, 0x80c, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA0__IPU_CSI_D_4 IOMUX_PAD(0x6b4, 0x250, 3, 0x940, 1, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA0__USB_TOP_USBH2_DATA_6 IOMUX_PAD(0x6b4, 0x250, 4, 0x9e4, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA0__GPIO2_2 IOMUX_PAD(0x6b4, 0x250, 5, 0x8c0, 1, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA0__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x6b4, 0x250, 6, 0x994, 3, NO_PAD_CTRL) + +#define MX35_PAD_SD2_DATA1__ESDHC2_DAT1 IOMUX_PAD(0x6b8, 0x254, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA1__UART3_TXD_MUX IOMUX_PAD(0x6b8, 0x254, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA1__ESDHC1_DAT7 IOMUX_PAD(0x6b8, 0x254, 2, 0x810, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA1__IPU_CSI_D_5 IOMUX_PAD(0x6b8, 0x254, 3, 0x944, 1, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA1__USB_TOP_USBH2_DATA_0 IOMUX_PAD(0x6b8, 0x254, 4, 0x9cc, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA1__GPIO2_3 IOMUX_PAD(0x6b8, 0x254, 5, 0x8cc, 1, NO_PAD_CTRL) + +#define MX35_PAD_SD2_DATA2__ESDHC2_DAT2 IOMUX_PAD(0x6bc, 0x258, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA2__UART3_RTS IOMUX_PAD(0x6bc, 0x258, 1, 0x99c, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA2__CAN1_RXCAN IOMUX_PAD(0x6bc, 0x258, 2, 0x7c8, 1, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA2__IPU_CSI_D_6 IOMUX_PAD(0x6bc, 0x258, 3, 0x948, 1, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA2__USB_TOP_USBH2_DATA_1 IOMUX_PAD(0x6bc, 0x258, 4, 0x9d0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA2__GPIO2_4 IOMUX_PAD(0x6bc, 0x258, 5, 0x8d0, 1, NO_PAD_CTRL) + +#define MX35_PAD_SD2_DATA3__ESDHC2_DAT3 IOMUX_PAD(0x6c0, 0x25c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA3__UART3_CTS IOMUX_PAD(0x6c0, 0x25c, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA3__CAN1_TXCAN IOMUX_PAD(0x6c0, 0x25c, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA3__IPU_CSI_D_7 IOMUX_PAD(0x6c0, 0x25c, 3, 0x94c, 1, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA3__USB_TOP_USBH2_DATA_2 IOMUX_PAD(0x6c0, 0x25c, 4, 0x9d4, 0, NO_PAD_CTRL) +#define MX35_PAD_SD2_DATA3__GPIO2_5 IOMUX_PAD(0x6c0, 0x25c, 5, 0x8d4, 1, NO_PAD_CTRL) + +#define MX35_PAD_ATA_CS0__ATA_CS0 IOMUX_PAD(0x6c4, 0x260, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS0__CSPI1_SS3 IOMUX_PAD(0x6c4, 0x260, 1, 0x7dc, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS0__IPU_DISPB_CS1 IOMUX_PAD(0x6c4, 0x260, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS0__GPIO2_6 IOMUX_PAD(0x6c4, 0x260, 5, 0x8d8, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS0__IPU_DIAGB_0 IOMUX_PAD(0x6c4, 0x260, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS0__ARM11P_TOP_MAX1_HMASTER_0 IOMUX_PAD(0x6c4, 0x260, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_CS1__ATA_CS1 IOMUX_PAD(0x6c8, 0x264, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS1__IPU_DISPB_CS2 IOMUX_PAD(0x6c8, 0x264, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS1__CSPI2_SS0 IOMUX_PAD(0x6c8, 0x264, 4, 0x7f0, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS1__GPIO2_7 IOMUX_PAD(0x6c8, 0x264, 5, 0x8dc, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS1__IPU_DIAGB_1 IOMUX_PAD(0x6c8, 0x264, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_CS1__ARM11P_TOP_MAX1_HMASTER_1 IOMUX_PAD(0x6c8, 0x264, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DIOR__ATA_DIOR IOMUX_PAD(0x6cc, 0x268, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOR__ESDHC3_DAT0 IOMUX_PAD(0x6cc, 0x268, 1, 0x81c, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOR__USB_TOP_USBOTG_DIR IOMUX_PAD(0x6cc, 0x268, 2, 0x9c4, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOR__IPU_DISPB_BE0 IOMUX_PAD(0x6cc, 0x268, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOR__CSPI2_SS1 IOMUX_PAD(0x6cc, 0x268, 4, 0x7f4, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOR__GPIO2_8 IOMUX_PAD(0x6cc, 0x268, 5, 0x8e0, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOR__IPU_DIAGB_2 IOMUX_PAD(0x6cc, 0x268, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOR__ARM11P_TOP_MAX1_HMASTER_2 IOMUX_PAD(0x6cc, 0x268, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DIOW__ATA_DIOW IOMUX_PAD(0x6d0, 0x26c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOW__ESDHC3_DAT1 IOMUX_PAD(0x6d0, 0x26c, 1, 0x820, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOW__USB_TOP_USBOTG_STP IOMUX_PAD(0x6d0, 0x26c, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOW__IPU_DISPB_BE1 IOMUX_PAD(0x6d0, 0x26c, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOW__CSPI2_MOSI IOMUX_PAD(0x6d0, 0x26c, 4, 0x7ec, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOW__GPIO2_9 IOMUX_PAD(0x6d0, 0x26c, 5, 0x8e4, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOW__IPU_DIAGB_3 IOMUX_PAD(0x6d0, 0x26c, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DIOW__ARM11P_TOP_MAX1_HMASTER_3 IOMUX_PAD(0x6d0, 0x26c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DMACK__ATA_DMACK IOMUX_PAD(0x6d4, 0x270, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMACK__ESDHC3_DAT2 IOMUX_PAD(0x6d4, 0x270, 1, 0x824, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMACK__USB_TOP_USBOTG_NXT IOMUX_PAD(0x6d4, 0x270, 2, 0x9c8, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMACK__CSPI2_MISO IOMUX_PAD(0x6d4, 0x270, 4, 0x7e8, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMACK__GPIO2_10 IOMUX_PAD(0x6d4, 0x270, 5, 0x86c, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMACK__IPU_DIAGB_4 IOMUX_PAD(0x6d4, 0x270, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMACK__ARM11P_TOP_MAX0_HMASTER_0 IOMUX_PAD(0x6d4, 0x270, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_RESET_B__ATA_RESET_B IOMUX_PAD(0x6d8, 0x274, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_RESET_B__ESDHC3_DAT3 IOMUX_PAD(0x6d8, 0x274, 1, 0x828, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_RESET_B__USB_TOP_USBOTG_DATA_0 IOMUX_PAD(0x6d8, 0x274, 2, 0x9a4, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_RESET_B__IPU_DISPB_SD_D_O IOMUX_PAD(0x6d8, 0x274, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_RESET_B__CSPI2_RDY IOMUX_PAD(0x6d8, 0x274, 4, 0x7e4, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_RESET_B__GPIO2_11 IOMUX_PAD(0x6d8, 0x274, 5, 0x870, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_RESET_B__IPU_DIAGB_5 IOMUX_PAD(0x6d8, 0x274, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_RESET_B__ARM11P_TOP_MAX0_HMASTER_1 IOMUX_PAD(0x6d8, 0x274, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_IORDY__ATA_IORDY IOMUX_PAD(0x6dc, 0x278, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_IORDY__ESDHC3_DAT4 IOMUX_PAD(0x6dc, 0x278, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_IORDY__USB_TOP_USBOTG_DATA_1 IOMUX_PAD(0x6dc, 0x278, 2, 0x9a8, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_IORDY__IPU_DISPB_SD_D_IO IOMUX_PAD(0x6dc, 0x278, 3, 0x92c, 3, NO_PAD_CTRL) +#define MX35_PAD_ATA_IORDY__ESDHC2_DAT4 IOMUX_PAD(0x6dc, 0x278, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_IORDY__GPIO2_12 IOMUX_PAD(0x6dc, 0x278, 5, 0x874, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_IORDY__IPU_DIAGB_6 IOMUX_PAD(0x6dc, 0x278, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_IORDY__ARM11P_TOP_MAX0_HMASTER_2 IOMUX_PAD(0x6dc, 0x278, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA0__ATA_DATA_0 IOMUX_PAD(0x6e0, 0x27c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA0__ESDHC3_DAT5 IOMUX_PAD(0x6e0, 0x27c, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA0__USB_TOP_USBOTG_DATA_2 IOMUX_PAD(0x6e0, 0x27c, 2, 0x9ac, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA0__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x6e0, 0x27c, 3, 0x928, 4, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA0__ESDHC2_DAT5 IOMUX_PAD(0x6e0, 0x27c, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA0__GPIO2_13 IOMUX_PAD(0x6e0, 0x27c, 5, 0x878, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA0__IPU_DIAGB_7 IOMUX_PAD(0x6e0, 0x27c, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA0__ARM11P_TOP_MAX0_HMASTER_3 IOMUX_PAD(0x6e0, 0x27c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA1__ATA_DATA_1 IOMUX_PAD(0x6e4, 0x280, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA1__ESDHC3_DAT6 IOMUX_PAD(0x6e4, 0x280, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA1__USB_TOP_USBOTG_DATA_3 IOMUX_PAD(0x6e4, 0x280, 2, 0x9b0, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA1__IPU_DISPB_SD_CLK IOMUX_PAD(0x6e4, 0x280, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA1__ESDHC2_DAT6 IOMUX_PAD(0x6e4, 0x280, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA1__GPIO2_14 IOMUX_PAD(0x6e4, 0x280, 5, 0x87c, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA1__IPU_DIAGB_8 IOMUX_PAD(0x6e4, 0x280, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA1__ARM11P_TOP_TRACE_27 IOMUX_PAD(0x6e4, 0x280, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA2__ATA_DATA_2 IOMUX_PAD(0x6e8, 0x284, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA2__ESDHC3_DAT7 IOMUX_PAD(0x6e8, 0x284, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA2__USB_TOP_USBOTG_DATA_4 IOMUX_PAD(0x6e8, 0x284, 2, 0x9b4, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA2__IPU_DISPB_SER_RS IOMUX_PAD(0x6e8, 0x284, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA2__ESDHC2_DAT7 IOMUX_PAD(0x6e8, 0x284, 4, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA2__GPIO2_15 IOMUX_PAD(0x6e8, 0x284, 5, 0x880, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA2__IPU_DIAGB_9 IOMUX_PAD(0x6e8, 0x284, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA2__ARM11P_TOP_TRACE_28 IOMUX_PAD(0x6e8, 0x284, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA3__ATA_DATA_3 IOMUX_PAD(0x6e8, 0x288, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA3__ESDHC3_CLK IOMUX_PAD(0x6e8, 0x288, 1, 0x814, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA3__USB_TOP_USBOTG_DATA_5 IOMUX_PAD(0x6e8, 0x288, 2, 0x9b8, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA3__CSPI2_SCLK IOMUX_PAD(0x6e8, 0x288, 4, 0x7e0, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA3__GPIO2_16 IOMUX_PAD(0x6e8, 0x288, 5, 0x884, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA3__IPU_DIAGB_10 IOMUX_PAD(0x6e8, 0x288, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA3__ARM11P_TOP_TRACE_29 IOMUX_PAD(0x6e8, 0x288, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA4__ATA_DATA_4 IOMUX_PAD(0x6f0, 0x28c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA4__ESDHC3_CMD IOMUX_PAD(0x6f0, 0x28c, 1, 0x818, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA4__USB_TOP_USBOTG_DATA_6 IOMUX_PAD(0x6f0, 0x28c, 2, 0x9bc, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA4__GPIO2_17 IOMUX_PAD(0x6f0, 0x28c, 5, 0x888, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA4__IPU_DIAGB_11 IOMUX_PAD(0x6f0, 0x28c, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA4__ARM11P_TOP_TRACE_30 IOMUX_PAD(0x6f0, 0x28c, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA5__ATA_DATA_5 IOMUX_PAD(0x6f4, 0x290, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA5__USB_TOP_USBOTG_DATA_7 IOMUX_PAD(0x6f4, 0x290, 2, 0x9c0, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA5__GPIO2_18 IOMUX_PAD(0x6f4, 0x290, 5, 0x88c, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA5__IPU_DIAGB_12 IOMUX_PAD(0x6f4, 0x290, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA5__ARM11P_TOP_TRACE_31 IOMUX_PAD(0x6f4, 0x290, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA6__ATA_DATA_6 IOMUX_PAD(0x6f8, 0x294, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA6__CAN1_TXCAN IOMUX_PAD(0x6f8, 0x294, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA6__UART1_DTR IOMUX_PAD(0x6f8, 0x294, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA6__AUDMUX_AUD6_TXD IOMUX_PAD(0x6f8, 0x294, 3, 0x7b4, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA6__GPIO2_19 IOMUX_PAD(0x6f8, 0x294, 5, 0x890, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA6__IPU_DIAGB_13 IOMUX_PAD(0x6f8, 0x294, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA7__ATA_DATA_7 IOMUX_PAD(0x6fc, 0x298, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA7__CAN1_RXCAN IOMUX_PAD(0x6fc, 0x298, 1, 0x7c8, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA7__UART1_DSR IOMUX_PAD(0x6fc, 0x298, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA7__AUDMUX_AUD6_RXD IOMUX_PAD(0x6fc, 0x298, 3, 0x7b0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA7__GPIO2_20 IOMUX_PAD(0x6fc, 0x298, 5, 0x898, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA7__IPU_DIAGB_14 IOMUX_PAD(0x6fc, 0x298, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA8__ATA_DATA_8 IOMUX_PAD(0x700, 0x29c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA8__UART3_RTS IOMUX_PAD(0x700, 0x29c, 1, 0x99c, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA8__UART1_RI IOMUX_PAD(0x700, 0x29c, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA8__AUDMUX_AUD6_TXC IOMUX_PAD(0x700, 0x29c, 3, 0x7c0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA8__GPIO2_21 IOMUX_PAD(0x700, 0x29c, 5, 0x89c, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA8__IPU_DIAGB_15 IOMUX_PAD(0x700, 0x29c, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA9__ATA_DATA_9 IOMUX_PAD(0x704, 0x2a0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA9__UART3_CTS IOMUX_PAD(0x704, 0x2a0, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA9__UART1_DCD IOMUX_PAD(0x704, 0x2a0, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA9__AUDMUX_AUD6_TXFS IOMUX_PAD(0x704, 0x2a0, 3, 0x7c4, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA9__GPIO2_22 IOMUX_PAD(0x704, 0x2a0, 5, 0x8a0, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA9__IPU_DIAGB_16 IOMUX_PAD(0x704, 0x2a0, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA10__ATA_DATA_10 IOMUX_PAD(0x708, 0x2a4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA10__UART3_RXD_MUX IOMUX_PAD(0x708, 0x2a4, 1, 0x9a0, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA10__AUDMUX_AUD6_RXC IOMUX_PAD(0x708, 0x2a4, 3, 0x7b8, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA10__GPIO2_23 IOMUX_PAD(0x708, 0x2a4, 5, 0x8a4, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA10__IPU_DIAGB_17 IOMUX_PAD(0x708, 0x2a4, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA11__ATA_DATA_11 IOMUX_PAD(0x70c, 0x2a8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA11__UART3_TXD_MUX IOMUX_PAD(0x70c, 0x2a8, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA11__AUDMUX_AUD6_RXFS IOMUX_PAD(0x70c, 0x2a8, 3, 0x7bc, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA11__GPIO2_24 IOMUX_PAD(0x70c, 0x2a8, 5, 0x8a8, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA11__IPU_DIAGB_18 IOMUX_PAD(0x70c, 0x2a8, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA12__ATA_DATA_12 IOMUX_PAD(0x710, 0x2ac, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA12__I2C3_SCL IOMUX_PAD(0x710, 0x2ac, 1, 0x91c, 3, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA12__GPIO2_25 IOMUX_PAD(0x710, 0x2ac, 5, 0x8ac, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA12__IPU_DIAGB_19 IOMUX_PAD(0x710, 0x2ac, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA13__ATA_DATA_13 IOMUX_PAD(0x714, 0x2b0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA13__I2C3_SDA IOMUX_PAD(0x714, 0x2b0, 1, 0x920, 3, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA13__GPIO2_26 IOMUX_PAD(0x714, 0x2b0, 5, 0x8b0, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA13__IPU_DIAGB_20 IOMUX_PAD(0x714, 0x2b0, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA14__ATA_DATA_14 IOMUX_PAD(0x718, 0x2b4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA14__IPU_CSI_D_0 IOMUX_PAD(0x718, 0x2b4, 1, 0x930, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA14__KPP_ROW_0 IOMUX_PAD(0x718, 0x2b4, 3, 0x970, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA14__GPIO2_27 IOMUX_PAD(0x718, 0x2b4, 5, 0x8b4, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA14__IPU_DIAGB_21 IOMUX_PAD(0x718, 0x2b4, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DATA15__ATA_DATA_15 IOMUX_PAD(0x71c, 0x2b8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA15__IPU_CSI_D_1 IOMUX_PAD(0x71c, 0x2b8, 1, 0x934, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA15__KPP_ROW_1 IOMUX_PAD(0x71c, 0x2b8, 3, 0x974, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA15__GPIO2_28 IOMUX_PAD(0x71c, 0x2b8, 5, 0x8b8, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DATA15__IPU_DIAGB_22 IOMUX_PAD(0x71c, 0x2b8, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_INTRQ__ATA_INTRQ IOMUX_PAD(0x720, 0x2bc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_INTRQ__IPU_CSI_D_2 IOMUX_PAD(0x720, 0x2bc, 1, 0x938, 3, NO_PAD_CTRL) +#define MX35_PAD_ATA_INTRQ__KPP_ROW_2 IOMUX_PAD(0x720, 0x2bc, 3, 0x978, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_INTRQ__GPIO2_29 IOMUX_PAD(0x720, 0x2bc, 5, 0x8bc, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_INTRQ__IPU_DIAGB_23 IOMUX_PAD(0x720, 0x2bc, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_BUFF_EN__ATA_BUFFER_EN IOMUX_PAD(0x724, 0x2c0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_BUFF_EN__IPU_CSI_D_3 IOMUX_PAD(0x724, 0x2c0, 1, 0x93c, 3, NO_PAD_CTRL) +#define MX35_PAD_ATA_BUFF_EN__KPP_ROW_3 IOMUX_PAD(0x724, 0x2c0, 3, 0x97c, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_BUFF_EN__GPIO2_30 IOMUX_PAD(0x724, 0x2c0, 5, 0x8c4, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_BUFF_EN__IPU_DIAGB_24 IOMUX_PAD(0x724, 0x2c0, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DMARQ__ATA_DMARQ IOMUX_PAD(0x728, 0x2c4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMARQ__IPU_CSI_D_4 IOMUX_PAD(0x728, 0x2c4, 1, 0x940, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMARQ__KPP_COL_0 IOMUX_PAD(0x728, 0x2c4, 3, 0x950, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMARQ__GPIO2_31 IOMUX_PAD(0x728, 0x2c4, 5, 0x8c8, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMARQ__IPU_DIAGB_25 IOMUX_PAD(0x728, 0x2c4, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DMARQ__ECT_CTI_TRIG_IN1_4 IOMUX_PAD(0x728, 0x2c4, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DA0__ATA_DA_0 IOMUX_PAD(0x72c, 0x2c8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA0__IPU_CSI_D_5 IOMUX_PAD(0x72c, 0x2c8, 1, 0x944, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA0__KPP_COL_1 IOMUX_PAD(0x72c, 0x2c8, 3, 0x954, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA0__GPIO3_0 IOMUX_PAD(0x72c, 0x2c8, 5, 0x8e8, 1, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA0__IPU_DIAGB_26 IOMUX_PAD(0x72c, 0x2c8, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA0__ECT_CTI_TRIG_IN1_5 IOMUX_PAD(0x72c, 0x2c8, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DA1__ATA_DA_1 IOMUX_PAD(0x730, 0x2cc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA1__IPU_CSI_D_6 IOMUX_PAD(0x730, 0x2cc, 1, 0x948, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA1__KPP_COL_2 IOMUX_PAD(0x730, 0x2cc, 3, 0x958, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA1__GPIO3_1 IOMUX_PAD(0x730, 0x2cc, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA1__IPU_DIAGB_27 IOMUX_PAD(0x730, 0x2cc, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA1__ECT_CTI_TRIG_IN1_6 IOMUX_PAD(0x730, 0x2cc, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_ATA_DA2__ATA_DA_2 IOMUX_PAD(0x734, 0x2d0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA2__IPU_CSI_D_7 IOMUX_PAD(0x734, 0x2d0, 1, 0x94c, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA2__KPP_COL_3 IOMUX_PAD(0x734, 0x2d0, 3, 0x95c, 2, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA2__GPIO3_2 IOMUX_PAD(0x734, 0x2d0, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA2__IPU_DIAGB_28 IOMUX_PAD(0x734, 0x2d0, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_ATA_DA2__ECT_CTI_TRIG_IN1_7 IOMUX_PAD(0x734, 0x2d0, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_MLB_CLK__MLB_MLBCLK IOMUX_PAD(0x738, 0x2d4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_MLB_CLK__GPIO3_3 IOMUX_PAD(0x738, 0x2d4, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_MLB_DAT__MLB_MLBDAT IOMUX_PAD(0x73c, 0x2d8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_MLB_DAT__GPIO3_4 IOMUX_PAD(0x73c, 0x2d8, 5, 0x904, 1, NO_PAD_CTRL) + +#define MX35_PAD_MLB_SIG__MLB_MLBSIG IOMUX_PAD(0x740, 0x2dc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_MLB_SIG__GPIO3_5 IOMUX_PAD(0x740, 0x2dc, 5, 0x908, 1, NO_PAD_CTRL) + +#define MX35_PAD_FEC_TX_CLK__FEC_TX_CLK IOMUX_PAD(0x744, 0x2e0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_CLK__ESDHC1_DAT4 IOMUX_PAD(0x744, 0x2e0, 1, 0x804, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_CLK__UART3_RXD_MUX IOMUX_PAD(0x744, 0x2e0, 2, 0x9a0, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_CLK__USB_TOP_USBH2_DIR IOMUX_PAD(0x744, 0x2e0, 3, 0x9ec, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_CLK__CSPI2_MOSI IOMUX_PAD(0x744, 0x2e0, 4, 0x7ec, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_CLK__GPIO3_6 IOMUX_PAD(0x744, 0x2e0, 5, 0x90c, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_CLK__IPU_DISPB_D12_VSYNC IOMUX_PAD(0x744, 0x2e0, 6, 0x928, 5, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_CLK__ARM11P_TOP_EVNTBUS_0 IOMUX_PAD(0x744, 0x2e0, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_RX_CLK__FEC_RX_CLK IOMUX_PAD(0x748, 0x2e4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_CLK__ESDHC1_DAT5 IOMUX_PAD(0x748, 0x2e4, 1, 0x808, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_CLK__UART3_TXD_MUX IOMUX_PAD(0x748, 0x2e4, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_CLK__USB_TOP_USBH2_STP IOMUX_PAD(0x748, 0x2e4, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_CLK__CSPI2_MISO IOMUX_PAD(0x748, 0x2e4, 4, 0x7e8, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_CLK__GPIO3_7 IOMUX_PAD(0x748, 0x2e4, 5, 0x910, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_CLK__IPU_DISPB_SD_D_I IOMUX_PAD(0x748, 0x2e4, 6, 0x92c, 4, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_CLK__ARM11P_TOP_EVNTBUS_1 IOMUX_PAD(0x748, 0x2e4, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_RX_DV__FEC_RX_DV IOMUX_PAD(0x74c, 0x2e8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_DV__ESDHC1_DAT6 IOMUX_PAD(0x74c, 0x2e8, 1, 0x80c, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_DV__UART3_RTS IOMUX_PAD(0x74c, 0x2e8, 2, 0x99c, 2, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_DV__USB_TOP_USBH2_NXT IOMUX_PAD(0x74c, 0x2e8, 3, 0x9f0, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_DV__CSPI2_SCLK IOMUX_PAD(0x74c, 0x2e8, 4, 0x7e0, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_DV__GPIO3_8 IOMUX_PAD(0x74c, 0x2e8, 5, 0x914, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_DV__IPU_DISPB_SD_CLK IOMUX_PAD(0x74c, 0x2e8, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_DV__ARM11P_TOP_EVNTBUS_2 IOMUX_PAD(0x74c, 0x2e8, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_COL__FEC_COL IOMUX_PAD(0x750, 0x2ec, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_COL__ESDHC1_DAT7 IOMUX_PAD(0x750, 0x2ec, 1, 0x810, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_COL__UART3_CTS IOMUX_PAD(0x750, 0x2ec, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_COL__USB_TOP_USBH2_DATA_0 IOMUX_PAD(0x750, 0x2ec, 3, 0x9cc, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_COL__CSPI2_RDY IOMUX_PAD(0x750, 0x2ec, 4, 0x7e4, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_COL__GPIO3_9 IOMUX_PAD(0x750, 0x2ec, 5, 0x918, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_COL__IPU_DISPB_SER_RS IOMUX_PAD(0x750, 0x2ec, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_COL__ARM11P_TOP_EVNTBUS_3 IOMUX_PAD(0x750, 0x2ec, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_RDATA0__FEC_RDATA_0 IOMUX_PAD(0x754, 0x2f0, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA0__PWM_PWMO IOMUX_PAD(0x754, 0x2f0, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA0__UART3_DTR IOMUX_PAD(0x754, 0x2f0, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA0__USB_TOP_USBH2_DATA_1 IOMUX_PAD(0x754, 0x2f0, 3, 0x9d0, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA0__CSPI2_SS0 IOMUX_PAD(0x754, 0x2f0, 4, 0x7f0, 2, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA0__GPIO3_10 IOMUX_PAD(0x754, 0x2f0, 5, 0x8ec, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA0__IPU_DISPB_CS1 IOMUX_PAD(0x754, 0x2f0, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA0__ARM11P_TOP_EVNTBUS_4 IOMUX_PAD(0x754, 0x2f0, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_TDATA0__FEC_TDATA_0 IOMUX_PAD(0x758, 0x2f4, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA0__SPDIF_SPDIF_OUT1 IOMUX_PAD(0x758, 0x2f4, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA0__UART3_DSR IOMUX_PAD(0x758, 0x2f4, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA0__USB_TOP_USBH2_DATA_2 IOMUX_PAD(0x758, 0x2f4, 3, 0x9d4, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA0__CSPI2_SS1 IOMUX_PAD(0x758, 0x2f4, 4, 0x7f4, 2, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA0__GPIO3_11 IOMUX_PAD(0x758, 0x2f4, 5, 0x8f0, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA0__IPU_DISPB_CS0 IOMUX_PAD(0x758, 0x2f4, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA0__ARM11P_TOP_EVNTBUS_5 IOMUX_PAD(0x758, 0x2f4, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_TX_EN__FEC_TX_EN IOMUX_PAD(0x75c, 0x2f8, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_EN__SPDIF_SPDIF_IN1 IOMUX_PAD(0x75c, 0x2f8, 1, 0x998, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_EN__UART3_RI IOMUX_PAD(0x75c, 0x2f8, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_EN__USB_TOP_USBH2_DATA_3 IOMUX_PAD(0x75c, 0x2f8, 3, 0x9d8, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_EN__GPIO3_12 IOMUX_PAD(0x75c, 0x2f8, 5, 0x8f4, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_EN__IPU_DISPB_PAR_RS IOMUX_PAD(0x75c, 0x2f8, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_EN__ARM11P_TOP_EVNTBUS_6 IOMUX_PAD(0x75c, 0x2f8, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_MDC__FEC_MDC IOMUX_PAD(0x760, 0x2fc, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDC__CAN2_TXCAN IOMUX_PAD(0x760, 0x2fc, 1, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDC__UART3_DCD IOMUX_PAD(0x760, 0x2fc, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDC__USB_TOP_USBH2_DATA_4 IOMUX_PAD(0x760, 0x2fc, 3, 0x9dc, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDC__GPIO3_13 IOMUX_PAD(0x760, 0x2fc, 5, 0x8f8, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDC__IPU_DISPB_WR IOMUX_PAD(0x760, 0x2fc, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDC__ARM11P_TOP_EVNTBUS_7 IOMUX_PAD(0x760, 0x2fc, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x764, 0x300, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDIO__CAN2_RXCAN IOMUX_PAD(0x764, 0x300, 1, 0x7cc, 2, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDIO__USB_TOP_USBH2_DATA_5 IOMUX_PAD(0x764, 0x300, 3, 0x9e0, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDIO__GPIO3_14 IOMUX_PAD(0x764, 0x300, 5, 0x8fc, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDIO__IPU_DISPB_RD IOMUX_PAD(0x764, 0x300, 6, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_MDIO__ARM11P_TOP_EVNTBUS_8 IOMUX_PAD(0x764, 0x300, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_TX_ERR__FEC_TX_ERR IOMUX_PAD(0x768, 0x304, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_ERR__OWIRE_LINE IOMUX_PAD(0x768, 0x304, 1, 0x990, 2, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_ERR__SPDIF_SPDIF_EXTCLK IOMUX_PAD(0x768, 0x304, 2, 0x994, 4, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_ERR__USB_TOP_USBH2_DATA_6 IOMUX_PAD(0x768, 0x304, 3, 0x9e4, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_ERR__GPIO3_15 IOMUX_PAD(0x768, 0x304, 5, 0x900, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_ERR__IPU_DISPB_D0_VSYNC IOMUX_PAD(0x768, 0x304, 6, 0x924, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_TX_ERR__ARM11P_TOP_EVNTBUS_9 IOMUX_PAD(0x768, 0x304, 7, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_RX_ERR__FEC_RX_ERR IOMUX_PAD(0x76c, 0x308, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_ERR__IPU_CSI_D_0 IOMUX_PAD(0x76c, 0x308, 1, 0x930, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_ERR__USB_TOP_USBH2_DATA_7 IOMUX_PAD(0x76c, 0x308, 3, 0x9e8, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_ERR__KPP_COL_4 IOMUX_PAD(0x76c, 0x308, 4, 0x960, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_ERR__GPIO3_16 IOMUX_PAD(0x76c, 0x308, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RX_ERR__IPU_DISPB_SD_D_IO IOMUX_PAD(0x76c, 0x308, 6, 0x92c, 5, NO_PAD_CTRL) + +#define MX35_PAD_FEC_CRS__FEC_CRS IOMUX_PAD(0x770, 0x30c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_CRS__IPU_CSI_D_1 IOMUX_PAD(0x770, 0x30c, 1, 0x934, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_CRS__USB_TOP_USBH2_PWR IOMUX_PAD(0x770, 0x30c, 3, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_CRS__KPP_COL_5 IOMUX_PAD(0x770, 0x30c, 4, 0x964, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_CRS__GPIO3_17 IOMUX_PAD(0x770, 0x30c, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_CRS__IPU_FLASH_STROBE IOMUX_PAD(0x770, 0x30c, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_RDATA1__FEC_RDATA_1 IOMUX_PAD(0x774, 0x310, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA1__IPU_CSI_D_2 IOMUX_PAD(0x774, 0x310, 1, 0x938, 4, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA1__AUDMUX_AUD6_RXC IOMUX_PAD(0x774, 0x310, 2, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA1__USB_TOP_USBH2_OC IOMUX_PAD(0x774, 0x310, 3, 0x9f4, 2, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA1__KPP_COL_6 IOMUX_PAD(0x774, 0x310, 4, 0x968, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA1__GPIO3_18 IOMUX_PAD(0x774, 0x310, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA1__IPU_DISPB_BE0 IOMUX_PAD(0x774, 0x310, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_TDATA1__FEC_TDATA_1 IOMUX_PAD(0x778, 0x314, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA1__IPU_CSI_D_3 IOMUX_PAD(0x778, 0x314, 1, 0x93c, 4, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA1__AUDMUX_AUD6_RXFS IOMUX_PAD(0x778, 0x314, 2, 0x7bc, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA1__KPP_COL_7 IOMUX_PAD(0x778, 0x314, 4, 0x96c, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA1__GPIO3_19 IOMUX_PAD(0x778, 0x314, 5, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA1__IPU_DISPB_BE1 IOMUX_PAD(0x778, 0x314, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_RDATA2__FEC_RDATA_2 IOMUX_PAD(0x77c, 0x318, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA2__IPU_CSI_D_4 IOMUX_PAD(0x77c, 0x318, 1, 0x940, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA2__AUDMUX_AUD6_TXD IOMUX_PAD(0x77c, 0x318, 2, 0x7b4, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA2__KPP_ROW_4 IOMUX_PAD(0x77c, 0x318, 4, 0x980, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA2__GPIO3_20 IOMUX_PAD(0x77c, 0x318, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_TDATA2__FEC_TDATA_2 IOMUX_PAD(0x780, 0x31c, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA2__IPU_CSI_D_5 IOMUX_PAD(0x780, 0x31c, 1, 0x944, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA2__AUDMUX_AUD6_RXD IOMUX_PAD(0x780, 0x31c, 2, 0x7b0, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA2__KPP_ROW_5 IOMUX_PAD(0x780, 0x31c, 4, 0x984, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA2__GPIO3_21 IOMUX_PAD(0x780, 0x31c, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_RDATA3__FEC_RDATA_3 IOMUX_PAD(0x784, 0x320, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA3__IPU_CSI_D_6 IOMUX_PAD(0x784, 0x320, 1, 0x948, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA3__AUDMUX_AUD6_TXC IOMUX_PAD(0x784, 0x320, 2, 0x7c0, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA3__KPP_ROW_6 IOMUX_PAD(0x784, 0x320, 4, 0x988, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_RDATA3__GPIO3_22 IOMUX_PAD(0x784, 0x320, 6, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_FEC_TDATA3__FEC_TDATA_3 IOMUX_PAD(0x788, 0x324, 0, 0x0, 0, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA3__IPU_CSI_D_7 IOMUX_PAD(0x788, 0x324, 1, 0x94c, 3, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA3__AUDMUX_AUD6_TXFS IOMUX_PAD(0x788, 0x324, 2, 0x7c4, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA3__KPP_ROW_7 IOMUX_PAD(0x788, 0x324, 4, 0x98c, 1, NO_PAD_CTRL) +#define MX35_PAD_FEC_TDATA3__GPIO3_23 IOMUX_PAD(0x788, 0x324, 5, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_EXT_ARMCLK__CCM_EXT_ARMCLK IOMUX_PAD(0x78c, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + +#define MX35_PAD_TEST_MODE__TCU_TEST_MODE IOMUX_PAD(0x790, 0x0, 0, 0x0, 0, NO_PAD_CTRL) + + +#endif /* __MACH_IOMUX_MX35_H__ */ diff --git a/arch/arm/plat-mxc/include/mach/iomux-v3.h b/arch/arm/plat-mxc/include/mach/iomux-v3.h new file mode 100644 index 00000000000..7cd84547658 --- /dev/null +++ b/arch/arm/plat-mxc/include/mach/iomux-v3.h @@ -0,0 +1,121 @@ +/* + * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH, + * <armlinux@phytec.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#ifndef __MACH_IOMUX_V3_H__ +#define __MACH_IOMUX_V3_H__ + +/* + * build IOMUX_PAD structure + * + * This iomux scheme is based around pads, which are the physical balls + * on the processor. + * + * - Each pad has a pad control register (IOMUXC_SW_PAD_CTRL_x) which controls + * things like driving strength and pullup/pulldown. + * - Each pad can have but not necessarily does have an output routing register + * (IOMUXC_SW_MUX_CTL_PAD_x). + * - Each pad can have but not necessarily does have an input routing register + * (IOMUXC_x_SELECT_INPUT) + * + * The three register sets do not have a fixed offset to each other, + * hence we order this table by pad control registers (which all pads + * have) and put the optional i/o routing registers into additional + * fields. + * + * The naming convention for the pad modes is MX35_PAD_<padname>__<padmode> + * If <padname> or <padmode> refers to a GPIO, it is named + * GPIO_<unit>_<num> + * + */ + +struct pad_desc { + unsigned mux_ctrl_ofs:12; /* IOMUXC_SW_MUX_CTL_PAD offset */ + unsigned mux_mode:8; + unsigned pad_ctrl_ofs:12; /* IOMUXC_SW_PAD_CTRL offset */ +#define NO_PAD_CTRL (1 << 16) + unsigned pad_ctrl:17; + unsigned select_input_ofs:12; /* IOMUXC_SELECT_INPUT offset */ + unsigned select_input:3; +}; + +#define IOMUX_PAD(_pad_ctrl_ofs, _mux_ctrl_ofs, _mux_mode, _select_input_ofs, \ + _select_input, _pad_ctrl) \ + { \ + .mux_ctrl_ofs = _mux_ctrl_ofs, \ + .mux_mode = _mux_mode, \ + .pad_ctrl_ofs = _pad_ctrl_ofs, \ + .pad_ctrl = _pad_ctrl, \ + .select_input_ofs = _select_input_ofs, \ + .select_input = _select_input, \ + } + +/* + * Use to set PAD control + */ +#define PAD_CTL_DRIVE_VOLTAGE_3_3_V 0 +#define PAD_CTL_DRIVE_VOLTAGE_1_8_V 1 + +#define PAD_CTL_NO_HYSTERESIS 0 +#define PAD_CTL_HYSTERESIS 1 + +#define PAD_CTL_PULL_DISABLED 0x0 +#define PAD_CTL_PULL_KEEPER 0xa +#define PAD_CTL_PULL_DOWN_100K 0xc +#define PAD_CTL_PULL_UP_47K 0xd +#define PAD_CTL_PULL_UP_100K 0xe +#define PAD_CTL_PULL_UP_22K 0xf + +#define PAD_CTL_OUTPUT_CMOS 0 +#define PAD_CTL_OUTPUT_OPEN_DRAIN 1 + +#define PAD_CTL_DRIVE_STRENGTH_NORM 0 +#define PAD_CTL_DRIVE_STRENGTH_HIGH 1 +#define PAD_CTL_DRIVE_STRENGTH_MAX 2 + +#define PAD_CTL_SLEW_RATE_SLOW 0 +#define PAD_CTL_SLEW_RATE_FAST 1 + +/* + * setups a single pad: + * - reserves the pad so that it is not claimed by another driver + * - setups the iomux according to the configuration + */ +int mxc_iomux_v3_setup_pad(struct pad_desc *pad); + +/* + * setups mutliple pads + * convenient way to call the above function with tables + */ +int mxc_iomux_v3_setup_multiple_pads(struct pad_desc *pad_list, unsigned count); + +/* + * releases a single pad: + * - make it available for a future use by another driver + * - DOES NOT reconfigure the IOMUX in its reset state + */ +void mxc_iomux_v3_release_pad(struct pad_desc *pad); + +/* + * releases multiple pads + * convenvient way to call the above function with tables + */ +void mxc_iomux_v3_release_multiple_pads(struct pad_desc *pad_list, int count); + +#endif /* __MACH_IOMUX_V3_H__*/ + diff --git a/arch/arm/plat-mxc/include/mach/memory.h b/arch/arm/plat-mxc/include/mach/memory.h index eca37d09f3f..6065e00176e 100644 --- a/arch/arm/plat-mxc/include/mach/memory.h +++ b/arch/arm/plat-mxc/include/mach/memory.h @@ -32,4 +32,12 @@ #define CONSISTENT_DMA_SIZE SZ_4M #endif /* CONFIG_MX1_VIDEO */ +#if defined(CONFIG_MX3_VIDEO) +/* + * Increase size of DMA-consistent memory region. + * This is required for mx3 camera driver to capture at least two QXGA frames. + */ +#define CONSISTENT_DMA_SIZE SZ_8M +#endif /* CONFIG_MX3_VIDEO */ + #endif /* __ASM_ARCH_MXC_MEMORY_H__ */ diff --git a/arch/arm/plat-mxc/include/mach/mx1.h b/arch/arm/plat-mxc/include/mach/mx1.h index b92e02324d8..1000bf330bc 100644 --- a/arch/arm/plat-mxc/include/mach/mx1.h +++ b/arch/arm/plat-mxc/include/mach/mx1.h @@ -179,7 +179,7 @@ #define DMA_REQ_UART1_T 30 #define DMA_REQ_UART1_R 31 -/* mandatory for CONFIG_LL_DEBUG */ +/* mandatory for CONFIG_DEBUG_LL */ #define MXC_LL_UART_PADDR UART1_BASE_ADDR #define MXC_LL_UART_VADDR IO_ADDRESS(UART1_BASE_ADDR) diff --git a/arch/arm/plat-mxc/include/mach/mx3x.h b/arch/arm/plat-mxc/include/mach/mx3x.h index 3878c6085d5..b559a4bb576 100644 --- a/arch/arm/plat-mxc/include/mach/mx3x.h +++ b/arch/arm/plat-mxc/include/mach/mx3x.h @@ -48,6 +48,9 @@ #define CS4_SIZE SZ_32M #define CS5_BASE_ADDR 0xB6000000 +#define CS5_BASE_ADDR_VIRT 0xF6000000 +#define CS5_SIZE SZ_32M + #define PCMCIA_MEM_BASE_ADDR 0xBC000000 /* @@ -191,6 +194,9 @@ #define CS4_IO_ADDRESS(x) \ (((x) - CS4_BASE_ADDR) + CS4_BASE_ADDR_VIRT) +#define CS5_IO_ADDRESS(x) \ + (((x) - CS5_BASE_ADDR) + CS5_BASE_ADDR_VIRT) + #define X_MEMC_IO_ADDRESS(x) \ (((x) - X_MEMC_BASE_ADDR) + X_MEMC_BASE_ADDR_VIRT) diff --git a/arch/arm/plat-mxc/include/mach/mxc_timer.h b/arch/arm/plat-mxc/include/mach/mxc_timer.h deleted file mode 100644 index 6c19a134744..00000000000 --- a/arch/arm/plat-mxc/include/mach/mxc_timer.h +++ /dev/null @@ -1,158 +0,0 @@ -/* - * mxc_timer.h - * - * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) - * - * Platform independent (i.MX1, i.MX2, i.MX3) definition for timer handling. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, - * Boston, MA 02110-1301, USA. - */ - -#ifndef __PLAT_MXC_TIMER_H -#define __PLAT_MXC_TIMER_H - -#include <linux/clk.h> -#include <mach/hardware.h> - -#ifdef CONFIG_ARCH_MX1 -#define TIMER_BASE IO_ADDRESS(TIM1_BASE_ADDR) -#define TIMER_INTERRUPT TIM1_INT - -#define TCTL_VAL TCTL_CLK_PCLK1 -#define TCTL_IRQEN (1<<4) -#define TCTL_FRR (1<<8) -#define TCTL_CLK_PCLK1 (1<<1) -#define TCTL_CLK_PCLK1_4 (2<<1) -#define TCTL_CLK_TIN (3<<1) -#define TCTL_CLK_32 (4<<1) - -#define MXC_TCTL 0x00 -#define MXC_TPRER 0x04 -#define MXC_TCMP 0x08 -#define MXC_TCR 0x0c -#define MXC_TCN 0x10 -#define MXC_TSTAT 0x14 -#define TSTAT_CAPT (1<<1) -#define TSTAT_COMP (1<<0) - -static inline void gpt_irq_disable(void) -{ - unsigned int tmp; - - tmp = __raw_readl(TIMER_BASE + MXC_TCTL); - __raw_writel(tmp & ~TCTL_IRQEN, TIMER_BASE + MXC_TCTL); -} - -static inline void gpt_irq_enable(void) -{ - __raw_writel(__raw_readl(TIMER_BASE + MXC_TCTL) | TCTL_IRQEN, - TIMER_BASE + MXC_TCTL); -} - -static void gpt_irq_acknowledge(void) -{ - __raw_writel(0, TIMER_BASE + MXC_TSTAT); -} -#endif /* CONFIG_ARCH_MX1 */ - -#ifdef CONFIG_ARCH_MX2 -#define TIMER_BASE IO_ADDRESS(GPT1_BASE_ADDR) -#define TIMER_INTERRUPT MXC_INT_GPT1 - -#define MXC_TCTL 0x00 -#define TCTL_VAL TCTL_CLK_PCLK1 -#define TCTL_CLK_PCLK1 (1<<1) -#define TCTL_CLK_PCLK1_4 (2<<1) -#define TCTL_IRQEN (1<<4) -#define TCTL_FRR (1<<8) -#define MXC_TPRER 0x04 -#define MXC_TCMP 0x08 -#define MXC_TCR 0x0c -#define MXC_TCN 0x10 -#define MXC_TSTAT 0x14 -#define TSTAT_CAPT (1<<1) -#define TSTAT_COMP (1<<0) - -static inline void gpt_irq_disable(void) -{ - unsigned int tmp; - - tmp = __raw_readl(TIMER_BASE + MXC_TCTL); - __raw_writel(tmp & ~TCTL_IRQEN, TIMER_BASE + MXC_TCTL); -} - -static inline void gpt_irq_enable(void) -{ - __raw_writel(__raw_readl(TIMER_BASE + MXC_TCTL) | TCTL_IRQEN, - TIMER_BASE + MXC_TCTL); -} - -static void gpt_irq_acknowledge(void) -{ - __raw_writel(TSTAT_CAPT | TSTAT_COMP, TIMER_BASE + MXC_TSTAT); -} -#endif /* CONFIG_ARCH_MX2 */ - -#ifdef CONFIG_ARCH_MX3 -#define TIMER_BASE IO_ADDRESS(GPT1_BASE_ADDR) -#define TIMER_INTERRUPT MXC_INT_GPT - -#define MXC_TCTL 0x00 -#define TCTL_VAL (TCTL_CLK_IPG | TCTL_WAITEN) -#define TCTL_CLK_IPG (1<<6) -#define TCTL_FRR (1<<9) -#define TCTL_WAITEN (1<<3) - -#define MXC_TPRER 0x04 -#define MXC_TSTAT 0x08 -#define TSTAT_OF1 (1<<0) -#define TSTAT_OF2 (1<<1) -#define TSTAT_OF3 (1<<2) -#define TSTAT_IF1 (1<<3) -#define TSTAT_IF2 (1<<4) -#define TSTAT_ROV (1<<5) -#define MXC_IR 0x0c -#define MXC_TCMP 0x10 -#define MXC_TCMP2 0x14 -#define MXC_TCMP3 0x18 -#define MXC_TCR 0x1c -#define MXC_TCN 0x24 - -static inline void gpt_irq_disable(void) -{ - __raw_writel(0, TIMER_BASE + MXC_IR); -} - -static inline void gpt_irq_enable(void) -{ - __raw_writel(1<<0, TIMER_BASE + MXC_IR); -} - -static inline void gpt_irq_acknowledge(void) -{ - __raw_writel(TSTAT_OF1, TIMER_BASE + MXC_TSTAT); -} -#endif /* CONFIG_ARCH_MX3 */ - -#define TCTL_SWR (1<<15) -#define TCTL_CC (1<<10) -#define TCTL_OM (1<<9) -#define TCTL_CAP_RIS (1<<6) -#define TCTL_CAP_FAL (2<<6) -#define TCTL_CAP_RIS_FAL (3<<6) -#define TCTL_CAP_ENA (1<<5) -#define TCTL_TEN (1<<0) - -#endif diff --git a/arch/arm/plat-mxc/include/mach/usb.h b/arch/arm/plat-mxc/include/mach/usb.h index 2dacb3086f1..be273371f34 100644 --- a/arch/arm/plat-mxc/include/mach/usb.h +++ b/arch/arm/plat-mxc/include/mach/usb.h @@ -17,7 +17,7 @@ struct imxusb_platform_data { int (*init)(struct device *); - int (*exit)(struct device *); + void (*exit)(struct device *); }; #endif /* __ASM_ARCH_MXC_USB */ diff --git a/arch/arm/plat-mxc/iomux-v3.c b/arch/arm/plat-mxc/iomux-v3.c new file mode 100644 index 00000000000..77a078f9513 --- /dev/null +++ b/arch/arm/plat-mxc/iomux-v3.c @@ -0,0 +1,98 @@ +/* + * Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de> + * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH, + * <armlinux@phytec.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ +#include <linux/errno.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/string.h> +#include <linux/gpio.h> + +#include <mach/hardware.h> +#include <asm/mach/map.h> +#include <mach/iomux-v3.h> + +#define IOMUX_BASE IO_ADDRESS(IOMUXC_BASE_ADDR) + +static unsigned long iomux_v3_pad_alloc_map[0x200 / BITS_PER_LONG]; + +/* + * setups a single pin: + * - reserves the pin so that it is not claimed by another driver + * - setups the iomux according to the configuration + */ +int mxc_iomux_v3_setup_pad(struct pad_desc *pad) +{ + unsigned int pad_ofs = pad->pad_ctrl_ofs; + + if (test_and_set_bit(pad_ofs >> 2, iomux_v3_pad_alloc_map)) + return -EBUSY; + if (pad->mux_ctrl_ofs) + __raw_writel(pad->mux_mode, IOMUX_BASE + pad->mux_ctrl_ofs); + + if (pad->select_input_ofs) + __raw_writel(pad->select_input, + IOMUX_BASE + pad->select_input_ofs); + + if (!(pad->pad_ctrl & NO_PAD_CTRL)) + __raw_writel(pad->pad_ctrl, IOMUX_BASE + pad->pad_ctrl_ofs); + return 0; +} +EXPORT_SYMBOL(mxc_iomux_v3_setup_pad); + +int mxc_iomux_v3_setup_multiple_pads(struct pad_desc *pad_list, unsigned count) +{ + struct pad_desc *p = pad_list; + int i; + int ret; + + for (i = 0; i < count; i++) { + ret = mxc_iomux_v3_setup_pad(p); + if (ret) + goto setup_error; + p++; + } + return 0; + +setup_error: + mxc_iomux_v3_release_multiple_pads(pad_list, i); + return ret; +} +EXPORT_SYMBOL(mxc_iomux_v3_setup_multiple_pads); + +void mxc_iomux_v3_release_pad(struct pad_desc *pad) +{ + unsigned int pad_ofs = pad->pad_ctrl_ofs; + + clear_bit(pad_ofs >> 2, iomux_v3_pad_alloc_map); +} +EXPORT_SYMBOL(mxc_iomux_v3_release_pad); + +void mxc_iomux_v3_release_multiple_pads(struct pad_desc *pad_list, int count) +{ + struct pad_desc *p = pad_list; + int i; + + for (i = 0; i < count; i++) { + mxc_iomux_v3_release_pad(p); + p++; + } +} +EXPORT_SYMBOL(mxc_iomux_v3_release_multiple_pads); diff --git a/arch/arm/plat-mxc/irq.c b/arch/arm/plat-mxc/irq.c index 0fb68a531f5..8aee76304f8 100644 --- a/arch/arm/plat-mxc/irq.c +++ b/arch/arm/plat-mxc/irq.c @@ -24,31 +24,27 @@ #include <asm/mach/irq.h> #include <mach/hardware.h> -#define AVIC_BASE IO_ADDRESS(AVIC_BASE_ADDR) -#define AVIC_INTCNTL (AVIC_BASE + 0x00) /* int control reg */ -#define AVIC_NIMASK (AVIC_BASE + 0x04) /* int mask reg */ -#define AVIC_INTENNUM (AVIC_BASE + 0x08) /* int enable number reg */ -#define AVIC_INTDISNUM (AVIC_BASE + 0x0C) /* int disable number reg */ -#define AVIC_INTENABLEH (AVIC_BASE + 0x10) /* int enable reg high */ -#define AVIC_INTENABLEL (AVIC_BASE + 0x14) /* int enable reg low */ -#define AVIC_INTTYPEH (AVIC_BASE + 0x18) /* int type reg high */ -#define AVIC_INTTYPEL (AVIC_BASE + 0x1C) /* int type reg low */ -#define AVIC_NIPRIORITY(x) (AVIC_BASE + (0x20 + 4 * (7 - (x)))) /* int priority */ -#define AVIC_NIVECSR (AVIC_BASE + 0x40) /* norm int vector/status */ -#define AVIC_FIVECSR (AVIC_BASE + 0x44) /* fast int vector/status */ -#define AVIC_INTSRCH (AVIC_BASE + 0x48) /* int source reg high */ -#define AVIC_INTSRCL (AVIC_BASE + 0x4C) /* int source reg low */ -#define AVIC_INTFRCH (AVIC_BASE + 0x50) /* int force reg high */ -#define AVIC_INTFRCL (AVIC_BASE + 0x54) /* int force reg low */ -#define AVIC_NIPNDH (AVIC_BASE + 0x58) /* norm int pending high */ -#define AVIC_NIPNDL (AVIC_BASE + 0x5C) /* norm int pending low */ -#define AVIC_FIPNDH (AVIC_BASE + 0x60) /* fast int pending high */ -#define AVIC_FIPNDL (AVIC_BASE + 0x64) /* fast int pending low */ - -#define SYSTEM_PREV_REG IO_ADDRESS(IIM_BASE_ADDR + 0x20) -#define SYSTEM_SREV_REG IO_ADDRESS(IIM_BASE_ADDR + 0x24) -#define IIM_PROD_REV_SH 3 -#define IIM_PROD_REV_LEN 5 +#define AVIC_INTCNTL 0x00 /* int control reg */ +#define AVIC_NIMASK 0x04 /* int mask reg */ +#define AVIC_INTENNUM 0x08 /* int enable number reg */ +#define AVIC_INTDISNUM 0x0C /* int disable number reg */ +#define AVIC_INTENABLEH 0x10 /* int enable reg high */ +#define AVIC_INTENABLEL 0x14 /* int enable reg low */ +#define AVIC_INTTYPEH 0x18 /* int type reg high */ +#define AVIC_INTTYPEL 0x1C /* int type reg low */ +#define AVIC_NIPRIORITY(x) (0x20 + 4 * (7 - (x))) /* int priority */ +#define AVIC_NIVECSR 0x40 /* norm int vector/status */ +#define AVIC_FIVECSR 0x44 /* fast int vector/status */ +#define AVIC_INTSRCH 0x48 /* int source reg high */ +#define AVIC_INTSRCL 0x4C /* int source reg low */ +#define AVIC_INTFRCH 0x50 /* int force reg high */ +#define AVIC_INTFRCL 0x54 /* int force reg low */ +#define AVIC_NIPNDH 0x58 /* norm int pending high */ +#define AVIC_NIPNDL 0x5C /* norm int pending low */ +#define AVIC_FIPNDH 0x60 /* fast int pending high */ +#define AVIC_FIPNDL 0x64 /* fast int pending low */ + +static void __iomem *avic_base; int imx_irq_set_priority(unsigned char irq, unsigned char prio) { @@ -59,11 +55,11 @@ int imx_irq_set_priority(unsigned char irq, unsigned char prio) if (irq >= MXC_INTERNAL_IRQS) return -EINVAL;; - temp = __raw_readl(AVIC_NIPRIORITY(irq / 8)); + temp = __raw_readl(avic_base + AVIC_NIPRIORITY(irq / 8)); temp &= ~mask; temp |= prio & mask; - __raw_writel(temp, AVIC_NIPRIORITY(irq / 8)); + __raw_writel(temp, avic_base + AVIC_NIPRIORITY(irq / 8)); return 0; #else @@ -81,12 +77,12 @@ int mxc_set_irq_fiq(unsigned int irq, unsigned int type) return -EINVAL; if (irq < MXC_INTERNAL_IRQS / 2) { - irqt = __raw_readl(AVIC_INTTYPEL) & ~(1 << irq); - __raw_writel(irqt | (!!type << irq), AVIC_INTTYPEL); + irqt = __raw_readl(avic_base + AVIC_INTTYPEL) & ~(1 << irq); + __raw_writel(irqt | (!!type << irq), avic_base + AVIC_INTTYPEL); } else { irq -= MXC_INTERNAL_IRQS / 2; - irqt = __raw_readl(AVIC_INTTYPEH) & ~(1 << irq); - __raw_writel(irqt | (!!type << irq), AVIC_INTTYPEH); + irqt = __raw_readl(avic_base + AVIC_INTTYPEH) & ~(1 << irq); + __raw_writel(irqt | (!!type << irq), avic_base + AVIC_INTTYPEH); } return 0; @@ -97,13 +93,13 @@ EXPORT_SYMBOL(mxc_set_irq_fiq); /* Disable interrupt number "irq" in the AVIC */ static void mxc_mask_irq(unsigned int irq) { - __raw_writel(irq, AVIC_INTDISNUM); + __raw_writel(irq, avic_base + AVIC_INTDISNUM); } /* Enable interrupt number "irq" in the AVIC */ static void mxc_unmask_irq(unsigned int irq) { - __raw_writel(irq, AVIC_INTENNUM); + __raw_writel(irq, avic_base + AVIC_INTENNUM); } static struct irq_chip mxc_avic_chip = { @@ -121,19 +117,21 @@ void __init mxc_init_irq(void) { int i; + avic_base = IO_ADDRESS(AVIC_BASE_ADDR); + /* put the AVIC into the reset value with * all interrupts disabled */ - __raw_writel(0, AVIC_INTCNTL); - __raw_writel(0x1f, AVIC_NIMASK); + __raw_writel(0, avic_base + AVIC_INTCNTL); + __raw_writel(0x1f, avic_base + AVIC_NIMASK); /* disable all interrupts */ - __raw_writel(0, AVIC_INTENABLEH); - __raw_writel(0, AVIC_INTENABLEL); + __raw_writel(0, avic_base + AVIC_INTENABLEH); + __raw_writel(0, avic_base + AVIC_INTENABLEL); /* all IRQ no FIQ */ - __raw_writel(0, AVIC_INTTYPEH); - __raw_writel(0, AVIC_INTTYPEL); + __raw_writel(0, avic_base + AVIC_INTTYPEH); + __raw_writel(0, avic_base + AVIC_INTTYPEL); for (i = 0; i < MXC_INTERNAL_IRQS; i++) { set_irq_chip(i, &mxc_avic_chip); set_irq_handler(i, handle_level_irq); @@ -142,7 +140,7 @@ void __init mxc_init_irq(void) /* Set default priority value (0) for all IRQ's */ for (i = 0; i < 8; i++) - __raw_writel(0, AVIC_NIPRIORITY(i)); + __raw_writel(0, avic_base + AVIC_NIPRIORITY(i)); /* init architectures chained interrupt handler */ mxc_register_gpios(); @@ -154,3 +152,4 @@ void __init mxc_init_irq(void) printk(KERN_INFO "MXC IRQ initialized\n"); } + diff --git a/arch/arm/plat-mxc/pwm.c b/arch/arm/plat-mxc/pwm.c index 9bffbc507cc..ae34198a79d 100644 --- a/arch/arm/plat-mxc/pwm.c +++ b/arch/arm/plat-mxc/pwm.c @@ -15,65 +15,26 @@ #include <linux/clk.h> #include <linux/io.h> #include <linux/pwm.h> +#include <mach/hardware.h> + + +/* i.MX1 and i.MX21 share the same PWM function block: */ + +#define MX1_PWMC 0x00 /* PWM Control Register */ +#define MX1_PWMS 0x04 /* PWM Sample Register */ +#define MX1_PWMP 0x08 /* PWM Period Register */ + + +/* i.MX27, i.MX31, i.MX35 share the same PWM function block: */ + +#define MX3_PWMCR 0x00 /* PWM Control Register */ +#define MX3_PWMSAR 0x0C /* PWM Sample Register */ +#define MX3_PWMPR 0x10 /* PWM Period Register */ +#define MX3_PWMCR_PRESCALER(x) (((x - 1) & 0xFFF) << 4) +#define MX3_PWMCR_CLKSRC_IPG_HIGH (2 << 16) +#define MX3_PWMCR_EN (1 << 0) + -#if defined CONFIG_ARCH_MX1 || defined CONFIG_ARCH_MX21 -#define PWM_VER_1 - -#define PWMCR 0x00 /* PWM Control Register */ -#define PWMSR 0x04 /* PWM Sample Register */ -#define PWMPR 0x08 /* PWM Period Register */ -#define PWMCNR 0x0C /* PWM Counter Register */ - -#define PWMCR_HCTR (1 << 18) /* Halfword FIFO Data Swapping */ -#define PWMCR_BCTR (1 << 17) /* Byte FIFO Data Swapping */ -#define PWMCR_SWR (1 << 16) /* Software Reset */ -#define PWMCR_CLKSRC_PERCLK (0 << 15) /* PERCLK Clock Source */ -#define PWMCR_CLKSRC_CLK32 (1 << 15) /* 32KHz Clock Source */ -#define PWMCR_PRESCALER(x) (((x - 1) & 0x7F) << 8) /* PRESCALER */ -#define PWMCR_IRQ (1 << 7) /* Interrupt Request */ -#define PWMCR_IRQEN (1 << 6) /* Interrupt Request Enable */ -#define PWMCR_FIFOAV (1 << 5) /* FIFO Available */ -#define PWMCR_EN (1 << 4) /* Enables/Disables the PWM */ -#define PWMCR_REPEAT(x) (((x) & 0x03) << 2) /* Sample Repeats */ -#define PWMCR_DIV(x) (((x) & 0x03) << 0) /* Clock divider 2/4/8/16 */ - -#define MAX_DIV (128 * 16) -#endif - -#if defined CONFIG_MACH_MX27 || defined CONFIG_ARCH_MX31 -#define PWM_VER_2 - -#define PWMCR 0x00 /* PWM Control Register */ -#define PWMSR 0x04 /* PWM Status Register */ -#define PWMIR 0x08 /* PWM Interrupt Register */ -#define PWMSAR 0x0C /* PWM Sample Register */ -#define PWMPR 0x10 /* PWM Period Register */ -#define PWMCNR 0x14 /* PWM Counter Register */ - -#define PWMCR_EN (1 << 0) /* Enables/Disables the PWM */ -#define PWMCR_REPEAT(x) (((x) & 0x03) << 1) /* Sample Repeats */ -#define PWMCR_SWR (1 << 3) /* Software Reset */ -#define PWMCR_PRESCALER(x) (((x - 1) & 0xFFF) << 4)/* PRESCALER */ -#define PWMCR_CLKSRC(x) (((x) & 0x3) << 16) -#define PWMCR_CLKSRC_OFF (0 << 16) -#define PWMCR_CLKSRC_IPG (1 << 16) -#define PWMCR_CLKSRC_IPG_HIGH (2 << 16) -#define PWMCR_CLKSRC_CLK32 (3 << 16) -#define PWMCR_POUTC -#define PWMCR_HCTR (1 << 20) /* Halfword FIFO Data Swapping */ -#define PWMCR_BCTR (1 << 21) /* Byte FIFO Data Swapping */ -#define PWMCR_DBGEN (1 << 22) /* Debug Mode */ -#define PWMCR_WAITEN (1 << 23) /* Wait Mode */ -#define PWMCR_DOZEN (1 << 24) /* Doze Mode */ -#define PWMCR_STOPEN (1 << 25) /* Stop Mode */ -#define PWMCR_FWM(x) (((x) & 0x3) << 26) /* FIFO Water Mark */ - -#define MAX_DIV 4096 -#endif - -#define PWMS_SAMPLE(x) ((x) & 0xFFFF) /* Contains a two-sample word */ -#define PWMP_PERIOD(x) ((x) & 0xFFFF) /* Represents the PWM's period */ -#define PWMC_COUNTER(x) ((x) & 0xFFFF) /* Represents the current count value */ struct pwm_device { struct list_head node; @@ -91,32 +52,52 @@ struct pwm_device { int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns) { - unsigned long long c; - unsigned long period_cycles, duty_cycles, prescale; - if (pwm == NULL || period_ns == 0 || duty_ns > period_ns) return -EINVAL; - c = clk_get_rate(pwm->clk); - c = c * period_ns; - do_div(c, 1000000000); - period_cycles = c; - - prescale = period_cycles / 0x10000 + 1; - - period_cycles /= prescale; - c = (unsigned long long)period_cycles * duty_ns; - do_div(c, period_ns); - duty_cycles = c; - -#ifdef PWM_VER_2 - writel(duty_cycles, pwm->mmio_base + PWMSAR); - writel(period_cycles, pwm->mmio_base + PWMPR); - writel(PWMCR_PRESCALER(prescale - 1) | PWMCR_CLKSRC_IPG_HIGH | PWMCR_EN, - pwm->mmio_base + PWMCR); -#elif defined PWM_VER_1 -#error PWM not yet working on MX1 / MX21 -#endif + if (cpu_is_mx27() || cpu_is_mx3()) { + unsigned long long c; + unsigned long period_cycles, duty_cycles, prescale; + c = clk_get_rate(pwm->clk); + c = c * period_ns; + do_div(c, 1000000000); + period_cycles = c; + + prescale = period_cycles / 0x10000 + 1; + + period_cycles /= prescale; + c = (unsigned long long)period_cycles * duty_ns; + do_div(c, period_ns); + duty_cycles = c; + + writel(duty_cycles, pwm->mmio_base + MX3_PWMSAR); + writel(period_cycles, pwm->mmio_base + MX3_PWMPR); + writel(MX3_PWMCR_PRESCALER(prescale - 1) | + MX3_PWMCR_CLKSRC_IPG_HIGH | MX3_PWMCR_EN, + pwm->mmio_base + MX3_PWMCR); + } else if (cpu_is_mx1() || cpu_is_mx21()) { + /* The PWM subsystem allows for exact frequencies. However, + * I cannot connect a scope on my device to the PWM line and + * thus cannot provide the program the PWM controller + * exactly. Instead, I'm relying on the fact that the + * Bootloader (u-boot or WinCE+haret) has programmed the PWM + * function group already. So I'll just modify the PWM sample + * register to follow the ratio of duty_ns vs. period_ns + * accordingly. + * + * This is good enought for programming the brightness of + * the LCD backlight. + * + * The real implementation would divide PERCLK[0] first by + * both the prescaler (/1 .. /128) and then by CLKSEL + * (/2 .. /16). + */ + u32 max = readl(pwm->mmio_base + MX1_PWMP); + u32 p = max * duty_ns / period_ns; + writel(max - p, pwm->mmio_base + MX1_PWMS); + } else { + BUG(); + } return 0; } @@ -297,4 +278,3 @@ module_exit(mxc_pwm_exit); MODULE_LICENSE("GPL v2"); MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de>"); - diff --git a/arch/arm/plat-mxc/time.c b/arch/arm/plat-mxc/time.c index dab3357196f..88fb3a57e02 100644 --- a/arch/arm/plat-mxc/time.c +++ b/arch/arm/plat-mxc/time.c @@ -29,22 +29,85 @@ #include <mach/hardware.h> #include <asm/mach/time.h> #include <mach/common.h> -#include <mach/mxc_timer.h> + +/* defines common for all i.MX */ +#define MXC_TCTL 0x00 +#define MXC_TCTL_TEN (1 << 0) +#define MXC_TPRER 0x04 + +/* MX1, MX21, MX27 */ +#define MX1_2_TCTL_CLK_PCLK1 (1 << 1) +#define MX1_2_TCTL_IRQEN (1 << 4) +#define MX1_2_TCTL_FRR (1 << 8) +#define MX1_2_TCMP 0x08 +#define MX1_2_TCN 0x10 +#define MX1_2_TSTAT 0x14 + +/* MX21, MX27 */ +#define MX2_TSTAT_CAPT (1 << 1) +#define MX2_TSTAT_COMP (1 << 0) + +/* MX31, MX35 */ +#define MX3_TCTL_WAITEN (1 << 3) +#define MX3_TCTL_CLK_IPG (1 << 6) +#define MX3_TCTL_FRR (1 << 9) +#define MX3_IR 0x0c +#define MX3_TSTAT 0x08 +#define MX3_TSTAT_OF1 (1 << 0) +#define MX3_TCN 0x24 +#define MX3_TCMP 0x10 static struct clock_event_device clockevent_mxc; static enum clock_event_mode clockevent_mode = CLOCK_EVT_MODE_UNUSED; -/* clock source */ +static void __iomem *timer_base; -static cycle_t mxc_get_cycles(struct clocksource *cs) +static inline void gpt_irq_disable(void) { - return __raw_readl(TIMER_BASE + MXC_TCN); + unsigned int tmp; + + if (cpu_is_mx3()) + __raw_writel(0, timer_base + MX3_IR); + else { + tmp = __raw_readl(timer_base + MXC_TCTL); + __raw_writel(tmp & ~MX1_2_TCTL_IRQEN, timer_base + MXC_TCTL); + } +} + +static inline void gpt_irq_enable(void) +{ + if (cpu_is_mx3()) + __raw_writel(1<<0, timer_base + MX3_IR); + else { + __raw_writel(__raw_readl(timer_base + MXC_TCTL) | MX1_2_TCTL_IRQEN, + timer_base + MXC_TCTL); + } +} + +static void gpt_irq_acknowledge(void) +{ + if (cpu_is_mx1()) + __raw_writel(0, timer_base + MX1_2_TSTAT); + if (cpu_is_mx2()) + __raw_writel(MX2_TSTAT_CAPT | MX2_TSTAT_COMP, timer_base + MX1_2_TSTAT); + if (cpu_is_mx3()) + __raw_writel(MX3_TSTAT_OF1, timer_base + MX3_TSTAT); +} + +static cycle_t mx1_2_get_cycles(struct clocksource *cs) +{ + return __raw_readl(timer_base + MX1_2_TCN); +} + +static cycle_t mx3_get_cycles(struct clocksource *cs) +{ + return __raw_readl(timer_base + MX3_TCN); } static struct clocksource clocksource_mxc = { .name = "mxc_timer1", .rating = 200, - .read = mxc_get_cycles, + .read = mx1_2_get_cycles, .mask = CLOCKSOURCE_MASK(32), .shift = 20, .flags = CLOCK_SOURCE_IS_CONTINUOUS, @@ -54,6 +117,9 @@ static int __init mxc_clocksource_init(struct clk *timer_clk) { unsigned int c = clk_get_rate(timer_clk); + if (cpu_is_mx3()) + clocksource_mxc.read = mx3_get_cycles; + clocksource_mxc.mult = clocksource_hz2mult(c, clocksource_mxc.shift); clocksource_register(&clocksource_mxc); @@ -63,15 +129,29 @@ static int __init mxc_clocksource_init(struct clk *timer_clk) /* clock event */ -static int mxc_set_next_event(unsigned long evt, +static int mx1_2_set_next_event(unsigned long evt, struct clock_event_device *unused) { unsigned long tcmp; - tcmp = __raw_readl(TIMER_BASE + MXC_TCN) + evt; - __raw_writel(tcmp, TIMER_BASE + MXC_TCMP); + tcmp = __raw_readl(timer_base + MX1_2_TCN) + evt; - return (int)(tcmp - __raw_readl(TIMER_BASE + MXC_TCN)) < 0 ? + __raw_writel(tcmp, timer_base + MX1_2_TCMP); + + return (int)(tcmp - __raw_readl(timer_base + MX1_2_TCN)) < 0 ? + -ETIME : 0; +} + +static int mx3_set_next_event(unsigned long evt, + struct clock_event_device *unused) +{ + unsigned long tcmp; + + tcmp = __raw_readl(timer_base + MX3_TCN) + evt; + + __raw_writel(tcmp, timer_base + MX3_TCMP); + + return (int)(tcmp - __raw_readl(timer_base + MX3_TCN)) < 0 ? -ETIME : 0; } @@ -100,8 +180,13 @@ static void mxc_set_mode(enum clock_event_mode mode, if (mode != clockevent_mode) { /* Set event time into far-far future */ - __raw_writel(__raw_readl(TIMER_BASE + MXC_TCN) - 3, - TIMER_BASE + MXC_TCMP); + if (cpu_is_mx3()) + __raw_writel(__raw_readl(timer_base + MX3_TCN) - 3, + timer_base + MX3_TCMP); + else + __raw_writel(__raw_readl(timer_base + MX1_2_TCN) - 3, + timer_base + MX1_2_TCMP); + /* Clear pending interrupt */ gpt_irq_acknowledge(); } @@ -148,7 +233,10 @@ static irqreturn_t mxc_timer_interrupt(int irq, void *dev_id) struct clock_event_device *evt = &clockevent_mxc; uint32_t tstat; - tstat = __raw_readl(TIMER_BASE + MXC_TSTAT); + if (cpu_is_mx3()) + tstat = __raw_readl(timer_base + MX3_TSTAT); + else + tstat = __raw_readl(timer_base + MX1_2_TSTAT); gpt_irq_acknowledge(); @@ -168,7 +256,7 @@ static struct clock_event_device clockevent_mxc = { .features = CLOCK_EVT_FEAT_ONESHOT, .shift = 32, .set_mode = mxc_set_mode, - .set_next_event = mxc_set_next_event, + .set_next_event = mx1_2_set_next_event, .rating = 200, }; @@ -176,6 +264,9 @@ static int __init mxc_clockevent_init(struct clk *timer_clk) { unsigned int c = clk_get_rate(timer_clk); + if (cpu_is_mx3()) + clockevent_mxc.set_next_event = mx3_set_next_event; + clockevent_mxc.mult = div_sc(c, NSEC_PER_SEC, clockevent_mxc.shift); clockevent_mxc.max_delta_ns = @@ -192,23 +283,47 @@ static int __init mxc_clockevent_init(struct clk *timer_clk) void __init mxc_timer_init(struct clk *timer_clk) { + uint32_t tctl_val; + int irq; + clk_enable(timer_clk); + if (cpu_is_mx1()) { +#ifdef CONFIG_ARCH_MX1 + timer_base = IO_ADDRESS(TIM1_BASE_ADDR); + irq = TIM1_INT; +#endif + } else if (cpu_is_mx2()) { +#ifdef CONFIG_ARCH_MX2 + timer_base = IO_ADDRESS(GPT1_BASE_ADDR); + irq = MXC_INT_GPT1; +#endif + } else if (cpu_is_mx3()) { +#ifdef CONFIG_ARCH_MX3 + timer_base = IO_ADDRESS(GPT1_BASE_ADDR); + irq = MXC_INT_GPT; +#endif + } else + BUG(); + /* * Initialise to a known state (all timers off, and timing reset) */ - __raw_writel(0, TIMER_BASE + MXC_TCTL); - __raw_writel(0, TIMER_BASE + MXC_TPRER); /* see datasheet note */ - __raw_writel(TCTL_FRR | /* free running */ - TCTL_VAL | /* set clocksource and arch specific bits */ - TCTL_TEN, /* start the timer */ - TIMER_BASE + MXC_TCTL); + __raw_writel(0, timer_base + MXC_TCTL); + __raw_writel(0, timer_base + MXC_TPRER); /* see datasheet note */ + + if (cpu_is_mx3()) + tctl_val = MX3_TCTL_CLK_IPG | MX3_TCTL_FRR | MX3_TCTL_WAITEN | MXC_TCTL_TEN; + else + tctl_val = MX1_2_TCTL_FRR | MX1_2_TCTL_CLK_PCLK1 | MXC_TCTL_TEN; + + __raw_writel(tctl_val, timer_base + MXC_TCTL); /* init and register the timer to the framework */ mxc_clocksource_init(timer_clk); mxc_clockevent_init(timer_clk); /* Make irqs happen */ - setup_irq(TIMER_INTERRUPT, &mxc_timer_irq); + setup_irq(irq, &mxc_timer_irq); } diff --git a/arch/arm/plat-omap/clock.c b/arch/arm/plat-omap/clock.c index 2e0614552ac..29efc279287 100644 --- a/arch/arm/plat-omap/clock.c +++ b/arch/arm/plat-omap/clock.c @@ -239,6 +239,13 @@ void recalculate_root_clocks(void) } } +/** + * clk_init_one - initialize any fields in the struct clk before clk init + * @clk: struct clk * to initialize + * + * Initialize any struct clk fields needed before normal clk initialization + * can run. No return value. + */ void clk_init_one(struct clk *clk) { INIT_LIST_HEAD(&clk->children); diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index 21cc0142b97..7fc8c045ad5 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -760,19 +760,12 @@ void omap_free_dma(int lch) { unsigned long flags; - spin_lock_irqsave(&dma_chan_lock, flags); if (dma_chan[lch].dev_id == -1) { pr_err("omap_dma: trying to free unallocated DMA channel %d\n", lch); - spin_unlock_irqrestore(&dma_chan_lock, flags); return; } - dma_chan[lch].dev_id = -1; - dma_chan[lch].next_lch = -1; - dma_chan[lch].callback = NULL; - spin_unlock_irqrestore(&dma_chan_lock, flags); - if (cpu_class_is_omap1()) { /* Disable all DMA interrupts for the channel. */ dma_write(0, CICR(lch)); @@ -798,6 +791,12 @@ void omap_free_dma(int lch) dma_write(0, CCR(lch)); omap_clear_dma(lch); } + + spin_lock_irqsave(&dma_chan_lock, flags); + dma_chan[lch].dev_id = -1; + dma_chan[lch].next_lch = -1; + dma_chan[lch].callback = NULL; + spin_unlock_irqrestore(&dma_chan_lock, flags); } EXPORT_SYMBOL(omap_free_dma); diff --git a/arch/arm/plat-omap/dmtimer.c b/arch/arm/plat-omap/dmtimer.c index bfd47570cc9..55bb9963129 100644 --- a/arch/arm/plat-omap/dmtimer.c +++ b/arch/arm/plat-omap/dmtimer.c @@ -238,7 +238,7 @@ static struct omap_dm_timer omap3_dm_timers[] = { { .phys_base = 0x49040000, .irq = INT_24XX_GPTIMER9 }, { .phys_base = 0x48086000, .irq = INT_24XX_GPTIMER10 }, { .phys_base = 0x48088000, .irq = INT_24XX_GPTIMER11 }, - { .phys_base = 0x48304000, .irq = INT_24XX_GPTIMER12 }, + { .phys_base = 0x48304000, .irq = INT_34XX_GPT12_IRQ }, }; static const char *omap3_dm_source_names[] __initdata = { @@ -321,11 +321,9 @@ static void omap_dm_timer_reset(struct omap_dm_timer *timer) l |= 0x2 << 8; /* Set clock activity to perserve f-clock on idle */ /* - * Enable wake-up only for GPT1 on OMAP2 CPUs. - * FIXME: All timers should have wake-up enabled and clear - * PRCM status. + * Enable wake-up on OMAP2 CPUs. */ - if (cpu_class_is_omap2() && (timer == &dm_timers[0])) + if (cpu_class_is_omap2()) l |= 1 << 2; omap_dm_timer_write_reg(timer, OMAP_TIMER_OCP_CFG_REG, l); @@ -511,7 +509,7 @@ EXPORT_SYMBOL_GPL(omap_dm_timer_stop); #ifdef CONFIG_ARCH_OMAP1 -void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source) +int omap_dm_timer_set_source(struct omap_dm_timer *timer, int source) { int n = (timer - dm_timers) << 1; u32 l; @@ -519,23 +517,31 @@ void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source) l = omap_readl(MOD_CONF_CTRL_1) & ~(0x03 << n); l |= source << n; omap_writel(l, MOD_CONF_CTRL_1); + + return 0; } EXPORT_SYMBOL_GPL(omap_dm_timer_set_source); #else -void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source) +int omap_dm_timer_set_source(struct omap_dm_timer *timer, int source) { + int ret = -EINVAL; + if (source < 0 || source >= 3) - return; + return -EINVAL; clk_disable(timer->fclk); - clk_set_parent(timer->fclk, dm_source_clocks[source]); + ret = clk_set_parent(timer->fclk, dm_source_clocks[source]); clk_enable(timer->fclk); - /* When the functional clock disappears, too quick writes seem to - * cause an abort. */ + /* + * When the functional clock disappears, too quick writes seem + * to cause an abort. XXX Is this still necessary? + */ __delay(150000); + + return ret; } EXPORT_SYMBOL_GPL(omap_dm_timer_set_source); diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index d3fa41e3d8c..17d7afe42b8 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -758,8 +758,12 @@ static void _clear_gpio_irqbank(struct gpio_bank *bank, int gpio_mask) /* Workaround for clearing DSP GPIO interrupts to allow retention */ #if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) + reg = bank->base + OMAP24XX_GPIO_IRQSTATUS2; if (cpu_is_omap24xx() || cpu_is_omap34xx()) - __raw_writel(gpio_mask, bank->base + OMAP24XX_GPIO_IRQSTATUS2); + __raw_writel(gpio_mask, reg); + + /* Flush posted write for the irq status to avoid spurious interrupts */ + __raw_readl(reg); #endif } @@ -921,13 +925,10 @@ static int _set_gpio_wakeup(struct gpio_bank *bank, int gpio, int enable) case METHOD_MPUIO: case METHOD_GPIO_1610: spin_lock_irqsave(&bank->lock, flags); - if (enable) { + if (enable) bank->suspend_wakeup |= (1 << gpio); - enable_irq_wake(bank->irq); - } else { - disable_irq_wake(bank->irq); + else bank->suspend_wakeup &= ~(1 << gpio); - } spin_unlock_irqrestore(&bank->lock, flags); return 0; #endif @@ -940,13 +941,10 @@ static int _set_gpio_wakeup(struct gpio_bank *bank, int gpio, int enable) return -EINVAL; } spin_lock_irqsave(&bank->lock, flags); - if (enable) { + if (enable) bank->suspend_wakeup |= (1 << gpio); - enable_irq_wake(bank->irq); - } else { - disable_irq_wake(bank->irq); + else bank->suspend_wakeup &= ~(1 << gpio); - } spin_unlock_irqrestore(&bank->lock, flags); return 0; #endif diff --git a/arch/arm/plat-omap/include/mach/dmtimer.h b/arch/arm/plat-omap/include/mach/dmtimer.h index 6dc70313821..20f1054c0a8 100644 --- a/arch/arm/plat-omap/include/mach/dmtimer.h +++ b/arch/arm/plat-omap/include/mach/dmtimer.h @@ -64,7 +64,7 @@ void omap_dm_timer_trigger(struct omap_dm_timer *timer); void omap_dm_timer_start(struct omap_dm_timer *timer); void omap_dm_timer_stop(struct omap_dm_timer *timer); -void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source); +int omap_dm_timer_set_source(struct omap_dm_timer *timer, int source); void omap_dm_timer_set_load(struct omap_dm_timer *timer, int autoreload, unsigned int value); void omap_dm_timer_set_load_start(struct omap_dm_timer *timer, int autoreload, unsigned int value); void omap_dm_timer_set_match(struct omap_dm_timer *timer, int enable, unsigned int match); diff --git a/arch/arm/plat-omap/include/mach/eac.h b/arch/arm/plat-omap/include/mach/eac.h deleted file mode 100644 index 9e62cf03027..00000000000 --- a/arch/arm/plat-omap/include/mach/eac.h +++ /dev/null @@ -1,100 +0,0 @@ -/* - * arch/arm/plat-omap/include/mach2/eac.h - * - * Defines for Enhanced Audio Controller - * - * Contact: Jarkko Nikula <jarkko.nikula@nokia.com> - * - * Copyright (C) 2006 Nokia Corporation - * Copyright (C) 2004 Texas Instruments, Inc. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, but - * WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - * General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA - * 02110-1301 USA - * - */ - -#ifndef __ASM_ARM_ARCH_OMAP2_EAC_H -#define __ASM_ARM_ARCH_OMAP2_EAC_H - -#include <mach/io.h> -#include <mach/hardware.h> -#include <asm/irq.h> - -#include <sound/core.h> - -/* master codec clock source */ -#define EAC_MCLK_EXT_MASK 0x100 -enum eac_mclk_src { - EAC_MCLK_INT_11290000, /* internal 96 MHz / 8.5 = 11.29 Mhz */ - EAC_MCLK_EXT_11289600 = EAC_MCLK_EXT_MASK, - EAC_MCLK_EXT_12288000, - EAC_MCLK_EXT_2x11289600, - EAC_MCLK_EXT_2x12288000, -}; - -/* codec port interface mode */ -enum eac_codec_mode { - EAC_CODEC_PCM, - EAC_CODEC_AC97, - EAC_CODEC_I2S_MASTER, /* codec port, I.e. EAC is the master */ - EAC_CODEC_I2S_SLAVE, -}; - -/* configuration structure for I2S mode */ -struct eac_i2s_conf { - /* if enabled, then first data slot (left channel) is signaled as - * positive level of frame sync EAC.AC_FS */ - unsigned polarity_changed_mode:1; - /* if enabled, then serial data starts one clock cycle after the - * of EAC.AC_FS for first audio slot */ - unsigned sync_delay_enable:1; -}; - -/* configuration structure for EAC codec port */ -struct eac_codec { - enum eac_mclk_src mclk_src; - - enum eac_codec_mode codec_mode; - union { - struct eac_i2s_conf i2s; - } codec_conf; - - int default_rate; /* audio sampling rate */ - - int (* set_power)(void *private_data, int dac, int adc); - int (* register_controls)(void *private_data, - struct snd_card *card); - const char *short_name; - - void *private_data; -}; - -/* structure for passing platform dependent data to the EAC driver */ -struct eac_platform_data { - int (* init)(struct device *eac_dev); - void (* cleanup)(struct device *eac_dev); - /* these callbacks are used to configure & control external MCLK - * source. NULL if not used */ - int (* enable_ext_clocks)(struct device *eac_dev); - void (* disable_ext_clocks)(struct device *eac_dev); -}; - -extern void omap_init_eac(struct eac_platform_data *pdata); - -extern int eac_register_codec(struct device *eac_dev, struct eac_codec *codec); -extern void eac_unregister_codec(struct device *eac_dev); - -extern int eac_set_mode(struct device *eac_dev, int play, int rec); - -#endif /* __ASM_ARM_ARCH_OMAP2_EAC_H */ diff --git a/arch/arm/plat-omap/include/mach/gpioexpander.h b/arch/arm/plat-omap/include/mach/gpioexpander.h deleted file mode 100644 index 90444a0d6b1..00000000000 --- a/arch/arm/plat-omap/include/mach/gpioexpander.h +++ /dev/null @@ -1,35 +0,0 @@ -/* - * arch/arm/plat-omap/include/mach/gpioexpander.h - * - * - * Copyright (C) 2004 Texas Instruments, Inc. - * - * This package is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR - * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED - * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. - */ - -#ifndef __ASM_ARCH_OMAP_GPIOEXPANDER_H -#define __ASM_ARCH_OMAP_GPIOEXPANDER_H - -/* Function Prototypes for GPIO Expander functions */ - -#ifdef CONFIG_GPIOEXPANDER_OMAP -int read_gpio_expa(u8 *, int); -int write_gpio_expa(u8 , int); -#else -static inline int read_gpio_expa(u8 *val, int addr) -{ - return 0; -} -static inline int write_gpio_expa(u8 val, int addr) -{ - return 0; -} -#endif - -#endif /* __ASM_ARCH_OMAP_GPIOEXPANDER_H */ diff --git a/arch/arm/plat-omap/include/mach/irda.h b/arch/arm/plat-omap/include/mach/irda.h index 8372a00d8e0..40f60339d1c 100644 --- a/arch/arm/plat-omap/include/mach/irda.h +++ b/arch/arm/plat-omap/include/mach/irda.h @@ -21,10 +21,6 @@ struct omap_irda_config { int transceiver_cap; int (*transceiver_mode)(struct device *dev, int mode); int (*select_irda)(struct device *dev, int state); - /* Very specific to the needs of some platforms (h3,h4) - * having calls which can sleep in irda_set_speed. - */ - struct delayed_work gpio_expa; int rx_channel; int tx_channel; unsigned long dest_start; diff --git a/arch/arm/plat-omap/include/mach/mmc.h b/arch/arm/plat-omap/include/mach/mmc.h index 4435bd434e1..81d5b36534b 100644 --- a/arch/arm/plat-omap/include/mach/mmc.h +++ b/arch/arm/plat-omap/include/mach/mmc.h @@ -79,7 +79,6 @@ struct omap_mmc_platform_data { /* use the internal clock */ unsigned internal_clock:1; - s16 power_pin; int switch_pin; /* gpio (card detect) */ int gpio_wp; /* gpio (write protect) */ diff --git a/arch/arm/plat-omap/include/mach/timer-gp.h b/arch/arm/plat-omap/include/mach/timer-gp.h new file mode 100644 index 00000000000..c88d346b59d --- /dev/null +++ b/arch/arm/plat-omap/include/mach/timer-gp.h @@ -0,0 +1,17 @@ +/* + * OMAP2/3 GPTIMER support.headers + * + * Copyright (C) 2009 Nokia Corporation + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + */ + +#ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_TIMER_GP_H +#define __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_TIMER_GP_H + +int __init omap2_gp_clockevent_set_gptimer(u8 id); + +#endif + diff --git a/arch/arm/plat-pxa/gpio.c b/arch/arm/plat-pxa/gpio.c index af819bf21b6..abc79d44aca 100644 --- a/arch/arm/plat-pxa/gpio.c +++ b/arch/arm/plat-pxa/gpio.c @@ -121,6 +121,8 @@ static int __init pxa_init_gpio_chip(int gpio_end) return -ENOMEM; } + memset(chips, 0, nbanks * sizeof(struct pxa_gpio_chip)); + for (i = 0, gpio = 0; i < nbanks; i++, gpio += 32) { struct gpio_chip *c = &chips[i].chip; @@ -143,6 +145,21 @@ static int __init pxa_init_gpio_chip(int gpio_end) return 0; } +/* Update only those GRERx and GFERx edge detection register bits if those + * bits are set in c->irq_mask + */ +static inline void update_edge_detect(struct pxa_gpio_chip *c) +{ + uint32_t grer, gfer; + + grer = __raw_readl(c->regbase + GRER_OFFSET) & ~c->irq_mask; + gfer = __raw_readl(c->regbase + GFER_OFFSET) & ~c->irq_mask; + grer |= c->irq_edge_rise & c->irq_mask; + gfer |= c->irq_edge_fall & c->irq_mask; + __raw_writel(grer, c->regbase + GRER_OFFSET); + __raw_writel(gfer, c->regbase + GFER_OFFSET); +} + static int pxa_gpio_irq_type(unsigned int irq, unsigned int type) { struct pxa_gpio_chip *c; @@ -181,8 +198,7 @@ static int pxa_gpio_irq_type(unsigned int irq, unsigned int type) else c->irq_edge_fall &= ~mask; - __raw_writel(c->irq_edge_rise & c->irq_mask, c->regbase + GRER_OFFSET); - __raw_writel(c->irq_edge_fall & c->irq_mask, c->regbase + GFER_OFFSET); + update_edge_detect(c); pr_debug("%s: IRQ%d (GPIO%d) - edge%s%s\n", __func__, irq, gpio, ((type & IRQ_TYPE_EDGE_RISING) ? " rising" : ""), @@ -244,8 +260,7 @@ static void pxa_unmask_muxed_gpio(unsigned int irq) struct pxa_gpio_chip *c = gpio_to_chip(gpio); c->irq_mask |= GPIO_bit(gpio); - __raw_writel(c->irq_edge_rise & c->irq_mask, c->regbase + GRER_OFFSET); - __raw_writel(c->irq_edge_fall & c->irq_mask, c->regbase + GFER_OFFSET); + update_edge_detect(c); } static struct irq_chip pxa_muxed_gpio_chip = { |