diff options
Diffstat (limited to 'arch/arm')
| -rw-r--r-- | arch/arm/mach-pxa/lubbock.c | 84 |
1 files changed, 84 insertions, 0 deletions
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c index 3e26d7ce5bb..1ab26c6914f 100644 --- a/arch/arm/mach-pxa/lubbock.c +++ b/arch/arm/mach-pxa/lubbock.c @@ -22,6 +22,10 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> +#include <linux/spi/spi.h> +#include <linux/spi/ads7846.h> +#include <asm/arch/pxa2xx_spi.h> + #include <asm/setup.h> #include <asm/memory.h> #include <asm/mach-types.h> @@ -196,6 +200,78 @@ static struct resource smc91x_resources[] = { }, }; +/* ADS7846 is connected through SSP ... and if your board has J5 populated, + * you can select it to replace the ucb1400 by switching the touchscreen cable + * (to J5) and poking board registers (as done below). Else it's only useful + * for the temperature sensors. + */ +static struct resource pxa_ssp_resources[] = { + [0] = { + .start = __PREG(SSCR0_P(1)), + .end = __PREG(SSCR0_P(1)) + 0x14, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_SSP, + .end = IRQ_SSP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct pxa2xx_spi_master pxa_ssp_master_info = { + .ssp_type = PXA25x_SSP, + .clock_enable = CKEN3_SSP, + .num_chipselect = 0, +}; + +static struct platform_device pxa_ssp = { + .name = "pxa2xx-spi", + .id = 1, + .resource = pxa_ssp_resources, + .num_resources = ARRAY_SIZE(pxa_ssp_resources), + .dev = { + .platform_data = &pxa_ssp_master_info, + }, +}; + +static int lubbock_ads7846_pendown_state(void) +{ + /* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */ + return 0; +} + +static struct ads7846_platform_data ads_info = { + .model = 7846, + .vref_delay_usecs = 100, /* internal, no cap */ + .get_pendown_state = lubbock_ads7846_pendown_state, + // .x_plate_ohms = 500, /* GUESS! */ + // .y_plate_ohms = 500, /* GUESS! */ +}; + +static void ads7846_cs(u32 command) +{ + static const unsigned TS_nCS = 1 << 11; + lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS); +} + +static struct pxa2xx_spi_chip ads_hw = { + .tx_threshold = 1, + .rx_threshold = 2, + .cs_control = ads7846_cs, +}; + +static struct spi_board_info spi_board_info[] __initdata = { { + .modalias = "ads7846", + .platform_data = &ads_info, + .controller_data = &ads_hw, + .irq = LUBBOCK_BB_IRQ, + .max_speed_hz = 120000 /* max sample rate at 3V */ + * 26 /* command + data + overhead */, + .bus_num = 1, + .chip_select = 0, +}, +}; + static struct platform_device smc91x_device = { .name = "smc91x", .id = -1, @@ -272,6 +348,7 @@ static struct platform_device *devices[] __initdata = { &smc91x_device, &lubbock_flash_device[0], &lubbock_flash_device[1], + &pxa_ssp, }; static struct pxafb_mach_info sharp_lm8v31 __initdata = { @@ -400,6 +477,8 @@ static void __init lubbock_init(void) lubbock_flash_data[flashboot^1].name = "application-flash"; lubbock_flash_data[flashboot].name = "boot-rom"; (void) platform_add_devices(devices, ARRAY_SIZE(devices)); + + spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info)); } static struct map_desc lubbock_io_desc[] __initdata = { @@ -416,6 +495,11 @@ static void __init lubbock_map_io(void) pxa_map_io(); iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc)); + /* SSP data pins */ + pxa_gpio_mode(GPIO23_SCLK_MD); + pxa_gpio_mode(GPIO25_STXD_MD); + pxa_gpio_mode(GPIO26_SRXD_MD); + /* This enables the BTUART */ pxa_gpio_mode(GPIO42_BTRXD_MD); pxa_gpio_mode(GPIO43_BTTXD_MD); |