diff options
Diffstat (limited to 'arch/avr32/boards/atstk1000/atstk1002.c')
| -rw-r--r-- | arch/avr32/boards/atstk1000/atstk1002.c | 129 |
1 files changed, 120 insertions, 9 deletions
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index cced73c5811..d47e39f0e97 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -7,38 +7,149 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/etherdevice.h> #include <linux/init.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/string.h> +#include <linux/types.h> +#include <linux/spi/spi.h> +#include <asm/io.h> +#include <asm/setup.h> +#include <asm/arch/at32ap7000.h> #include <asm/arch/board.h> #include <asm/arch/init.h> +#include <asm/arch/portmux.h> -struct eth_platform_data __initdata eth0_data = { - .valid = 1, - .mii_phy_addr = 0x10, - .is_rmii = 0, - .hw_addr = { 0x6a, 0x87, 0x71, 0x14, 0xcd, 0xcb }, + +#define SW2_DEFAULT /* MMCI and UART_A available */ + +struct eth_addr { + u8 addr[6]; }; +static struct eth_addr __initdata hw_addr[2]; + +static struct eth_platform_data __initdata eth_data[2]; extern struct lcdc_platform_data atstk1000_fb0_data; +static struct spi_board_info spi_board_info[] __initdata = { + { + .modalias = "ltv350qv", + .controller_data = (void *)GPIO_PIN_PA(4), + .max_speed_hz = 16000000, + .bus_num = 0, + .chip_select = 1, + }, +}; + +/* + * The next two functions should go away as the boot loader is + * supposed to initialize the macb address registers with a valid + * ethernet address. But we need to keep it around for a while until + * we can be reasonably sure the boot loader does this. + * + * The phy_id is ignored as the driver will probe for it. + */ +static int __init parse_tag_ethernet(struct tag *tag) +{ + int i; + + i = tag->u.ethernet.mac_index; + if (i < ARRAY_SIZE(hw_addr)) + memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address, + sizeof(hw_addr[i].addr)); + + return 0; +} +__tagtable(ATAG_ETHERNET, parse_tag_ethernet); + +static void __init set_hw_addr(struct platform_device *pdev) +{ + struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + const u8 *addr; + void __iomem *regs; + struct clk *pclk; + + if (!res) + return; + if (pdev->id >= ARRAY_SIZE(hw_addr)) + return; + + addr = hw_addr[pdev->id].addr; + if (!is_valid_ether_addr(addr)) + return; + + /* + * Since this is board-specific code, we'll cheat and use the + * physical address directly as we happen to know that it's + * the same as the virtual address. + */ + regs = (void __iomem __force *)res->start; + pclk = clk_get(&pdev->dev, "pclk"); + if (!pclk) + return; + + clk_enable(pclk); + __raw_writel((addr[3] << 24) | (addr[2] << 16) + | (addr[1] << 8) | addr[0], regs + 0x98); + __raw_writel((addr[5] << 8) | addr[4], regs + 0x9c); + clk_disable(pclk); + clk_put(pclk); +} + void __init setup_board(void) { - at32_map_usart(1, 0); /* /dev/ttyS0 */ - at32_map_usart(2, 1); /* /dev/ttyS1 */ - at32_map_usart(3, 2); /* /dev/ttyS2 */ +#ifdef SW2_DEFAULT + at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */ +#else + at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */ +#endif + /* USART 2/unused: expansion connector */ + at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */ at32_setup_serial_console(0); } static int __init atstk1002_init(void) { + /* + * ATSTK1000 uses 32-bit SDRAM interface. Reserve the + * SDRAM-specific pins so that nobody messes with them. + */ + at32_reserve_pin(GPIO_PIN_PE(0)); /* DATA[16] */ + at32_reserve_pin(GPIO_PIN_PE(1)); /* DATA[17] */ + at32_reserve_pin(GPIO_PIN_PE(2)); /* DATA[18] */ + at32_reserve_pin(GPIO_PIN_PE(3)); /* DATA[19] */ + at32_reserve_pin(GPIO_PIN_PE(4)); /* DATA[20] */ + at32_reserve_pin(GPIO_PIN_PE(5)); /* DATA[21] */ + at32_reserve_pin(GPIO_PIN_PE(6)); /* DATA[22] */ + at32_reserve_pin(GPIO_PIN_PE(7)); /* DATA[23] */ + at32_reserve_pin(GPIO_PIN_PE(8)); /* DATA[24] */ + at32_reserve_pin(GPIO_PIN_PE(9)); /* DATA[25] */ + at32_reserve_pin(GPIO_PIN_PE(10)); /* DATA[26] */ + at32_reserve_pin(GPIO_PIN_PE(11)); /* DATA[27] */ + at32_reserve_pin(GPIO_PIN_PE(12)); /* DATA[28] */ + at32_reserve_pin(GPIO_PIN_PE(13)); /* DATA[29] */ + at32_reserve_pin(GPIO_PIN_PE(14)); /* DATA[30] */ + at32_reserve_pin(GPIO_PIN_PE(15)); /* DATA[31] */ + at32_reserve_pin(GPIO_PIN_PE(26)); /* SDCS */ + at32_add_system_devices(); +#ifdef SW2_DEFAULT at32_add_device_usart(0); +#else at32_add_device_usart(1); +#endif at32_add_device_usart(2); - at32_add_device_eth(0, ð0_data); + set_hw_addr(at32_add_device_eth(0, ð_data[0])); + + spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info)); at32_add_device_spi(0); at32_add_device_lcdc(0, &atstk1000_fb0_data); |