1 files changed, 62 insertions, 38 deletions

diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index b1b111bb2f3..017defaa525 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -71,6 +71,7 @@ config GENERIC_CALIBRATE_DELAY
 
 config IRQCHIP_DEMUX_GPIO
 	bool
+	depends on (BF53x || BF561 || BF54x)
 	default y
 
 source "init/Kconfig"
@@ -114,6 +115,26 @@ config BF537
 	help
 	  BF537 Processor Support.
 
+config BF542
+	bool "BF542"
+	help
+	  BF542 Processor Support.
+
+config BF544
+	bool "BF544"
+	help
+	  BF544 Processor Support.
+
+config BF548
+	bool "BF548"
+	help
+	  BF548 Processor Support.
+
+config BF549
+	bool "BF549"
+	help
+	  BF549 Processor Support.
+
 config BF561
 	bool "BF561"
 	help
@@ -125,6 +146,11 @@ choice
 	prompt "Silicon Rev"
 	default BF_REV_0_2 if BF537
 	default BF_REV_0_3 if BF533
+	default BF_REV_0_0 if BF549
+
+config BF_REV_0_0
+	bool "0.0"
+	depends on (BF549)
 
 config BF_REV_0_2
 	bool "0.2"
@@ -142,8 +168,24 @@ config BF_REV_0_5
 	bool "0.5"
 	depends on (BF561 || BF533 || BF532 || BF531)
 
+config BF_REV_ANY
+	bool "any"
+
+config BF_REV_NONE
+	bool "none"
+
 endchoice
 
+config BF53x
+	bool
+	depends on (BF531 || BF532 || BF533 || BF534 || BF536 || BF537)
+	default y
+
+config BF54x
+	bool
+	depends on (BF542 || BF544 || BF548 || BF549)
+	default y
+
 config BFIN_DUAL_CORE
 	bool
 	depends on (BF561)
@@ -192,6 +234,12 @@ config BFIN537_BLUETECHNIX_CM
 	help
 	  CM-BF537 support for EVAL- and DEV-Board.
 
+config BFIN548_EZKIT
+	bool "BF548-EZKIT"
+	depends on (BF548 || BF549)
+	  help
+	  BFIN548-EZKIT board Support.
+
 config BFIN561_BLUETECHNIX_CM
 	bool "Bluetechnix CM-BF561"
 	depends on (BF561)
@@ -259,6 +307,7 @@ config BFIN_SHARED_FLASH_ENET
 source "arch/blackfin/mach-bf533/Kconfig"
 source "arch/blackfin/mach-bf561/Kconfig"
 source "arch/blackfin/mach-bf537/Kconfig"
+source "arch/blackfin/mach-bf548/Kconfig"
 
 menu "Board customizations"
 
@@ -394,41 +443,6 @@ config BFIN_IDLE_LED_PIN
 	default 0x08 if (BFIN533_STAMP && BFIN_IDLE_LED_NUM = 2)
 	default 0x10 if (BFIN533_STAMP && BFIN_IDLE_LED_NUM = 3)
 
-comment "Console UART Setup"
-
-choice
-	prompt "Baud Rate"
-	default BAUD_57600
-config BAUD_9600
-	bool "9600"
-config BAUD_19200
-	bool "19200"
-config BAUD_38400
-	bool "38400"
-config BAUD_57600
-	bool "57600"
-config BAUD_115200
-	bool "115200"
-endchoice
-
-choice
-	prompt "Parity"
-	default BAUD_NO_PARITY
-config  BAUD_NO_PARITY
-	bool "No Parity"
-config  BAUD_PARITY
-	bool "Parity"
-endchoice
-
-choice
-	prompt "Stop Bits"
-	default BAUD_1_STOPBIT
-config  BAUD_1_STOPBIT
-	bool "1"
-config  BAUD_2_STOPBIT
-	bool "2"
-endchoice
-
 endmenu
 
 
@@ -526,7 +540,8 @@ config IP_CHECKSUM_L1
 
 config CACHELINE_ALIGNED_L1
 	bool "Locate cacheline_aligned data to L1 Data Memory"
-	default y
+	default y if !BF54x
+	default n if BF54x
 	depends on !BF531
 	help
 	  If enabled cacheline_anligned data is linked
@@ -570,9 +585,17 @@ endchoice
 
 source "mm/Kconfig"
 
+config LARGE_ALLOCS
+	bool "Allow allocating large blocks (> 1MB) of memory"
+	help
+	  Allow the slab memory allocator to keep chains for very large
+	  memory sizes - upto 32MB. You may need this if your system has
+	  a lot of RAM, and you need to able to allocate very large
+	  contiguous chunks. If unsure, say N.
+
 config BFIN_DMA_5XX
 	bool "Enable DMA Support"
-	depends on (BF533 || BF532 || BF531 || BF537 || BF536 || BF534 || BF561)
+	depends on (BF533 || BF532 || BF531 || BF537 || BF536 || BF534 || BF561 || BF54x)
 	default y
 	help
 	  DMA driver for BF5xx.
@@ -715,6 +738,7 @@ config C_AMCKEN
 
 config C_CDPRIO
 	bool "DMA has priority over core for ext. accesses"
+	depends on !BF54x
 	default n
 
 config C_B0PEN
@@ -868,7 +892,7 @@ endchoice
 
 endmenu
 
-if (BF537 || BF533)
+if (BF537 || BF533 || BF54x)
 
 menu "CPU Frequency scaling"