diff options
Diffstat (limited to 'arch/blackfin/mach-bf537/head.S')
| -rw-r--r-- | arch/blackfin/mach-bf537/head.S | 103 |
1 files changed, 30 insertions, 73 deletions
diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S index d104e1d8e07..2c2652bee7e 100644 --- a/arch/blackfin/mach-bf537/head.S +++ b/arch/blackfin/mach-bf537/head.S @@ -181,7 +181,8 @@ ENTRY(__stext) SSYNC; #endif - /*Initialise UART*/ + /* Initialise UART - when booting from u-boot, the UART is not disabled + * so if we dont initalize here, our serial console gets hosed */ p0.h = hi(UART_LCR); p0.l = lo(UART_LCR); r0 = 0x0(Z); @@ -469,47 +470,41 @@ ENTRY(_bfin_reset) SSYNC; #if defined(CONFIG_MTD_M25P80) -/* - * The following code fix the SPI flash reboot issue, - * /CS signal of the chip which is using PF10 return to GPIO mode - */ + /* + * The following code fix the SPI flash reboot issue, + * /CS signal of the chip which is using PF10 return to GPIO mode + */ p0.h = hi(PORTF_FER); p0.l = lo(PORTF_FER); r0.l = 0x0000; w[p0] = r0.l; SSYNC; -/* /CS return to high */ + /* /CS return to high */ p0.h = hi(PORTFIO); p0.l = lo(PORTFIO); r0.l = 0xFFFF; w[p0] = r0.l; SSYNC; -/* Delay some time, This is necessary */ + /* Delay some time, This is necessary */ r1.h = 0; r1.l = 0x400; p1 = r1; - lsetup (_delay_lab1,_delay_lab1_end ) lc1 = p1; -_delay_lab1: + lsetup (.L_delay_lab1, .L_delay_lab1_end) lc1 = p1; +.L_delay_lab1: r0.h = 0; r0.l = 0x8000; p0 = r0; - lsetup (_delay_lab0,_delay_lab0_end ) lc0 = p0; -_delay_lab0: + lsetup (.L_delay_lab0, .L_delay_lab0_end) lc0 = p0; +.L_delay_lab0: nop; -_delay_lab0_end: +.L_delay_lab0_end: nop; -_delay_lab1_end: +.L_delay_lab1_end: nop; #endif - /* Clear the bits 13-15 in SWRST if they werent cleared */ - p0.h = hi(SWRST); - p0.l = lo(SWRST); - csync; - r0.l = w[p0]; - /* Clear the IMASK register */ p0.h = hi(IMASK); p0.l = lo(IMASK); @@ -523,68 +518,30 @@ _delay_lab1_end: [p0] = r0; SSYNC; - /* Disable the WDOG TIMER */ - p0.h = hi(WDOG_CTL); - p0.l = lo(WDOG_CTL); - r0.l = 0xAD6; - w[p0] = r0.l; - SSYNC; - - /* Clear the sticky bit incase it is already set */ - p0.h = hi(WDOG_CTL); - p0.l = lo(WDOG_CTL); - r0.l = 0x8AD6; - w[p0] = r0.l; - SSYNC; - - /* Program the count value */ - R0.l = 0x100; - R0.h = 0x0; - P0.h = hi(WDOG_CNT); - P0.l = lo(WDOG_CNT); - [P0] = R0; - SSYNC; - - /* Program WDOG_STAT if necessary */ - P0.h = hi(WDOG_CTL); - P0.l = lo(WDOG_CTL); - R0 = W[P0](Z); - CC = BITTST(R0,1); - if !CC JUMP .LWRITESTAT; - CC = BITTST(R0,2); - if !CC JUMP .LWRITESTAT; - JUMP .LSKIP_WRITE; - -.LWRITESTAT: - /* When watch dog timer is enabled, - * a write to STAT will load the contents of CNT to STAT - */ - R0 = 0x0000(z); - P0.h = hi(WDOG_STAT); - P0.l = lo(WDOG_STAT) - [P0] = R0; + /* make sure SYSCR is set to use BMODE */ + P0.h = hi(SYSCR); + P0.l = lo(SYSCR); + R0.l = 0x0; + W[P0] = R0.l; SSYNC; -.LSKIP_WRITE: - /* Enable the reset event */ - P0.h = hi(WDOG_CTL); - P0.l = lo(WDOG_CTL); - R0 = W[P0](Z); - BITCLR(R0,1); - BITCLR(R0,2); - W[P0] = R0.L; + /* issue a system soft reset */ + P1.h = hi(SWRST); + P1.l = lo(SWRST); + R1.l = 0x0007; + W[P1] = R1; SSYNC; - NOP; - /* Enable the wdog counter */ - R0 = W[P0](Z); - BITCLR(R0,4); - W[P0] = R0.L; + /* clear system soft reset */ + R0.l = 0x0000; + W[P0] = R0; SSYNC; - IDLE; + /* issue core reset */ + raise 1; RTS; +ENDPROC(_bfin_reset) .data |