aboutsummaryrefslogtreecommitdiff
path: root/drivers/block
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/block')
-rw-r--r--drivers/block/aoe/aoe.h1
-rw-r--r--drivers/block/aoe/aoenet.c2
-rw-r--r--drivers/block/cciss.c215
-rw-r--r--drivers/block/floppy.c79
-rw-r--r--drivers/block/paride/pg.c2
5 files changed, 271 insertions, 28 deletions
diff --git a/drivers/block/aoe/aoe.h b/drivers/block/aoe/aoe.h
index c237527b1aa..5e41e6dd657 100644
--- a/drivers/block/aoe/aoe.h
+++ b/drivers/block/aoe/aoe.h
@@ -18,6 +18,7 @@
enum {
AOECMD_ATA,
AOECMD_CFG,
+ AOECMD_VEND_MIN = 0xf0,
AOEFL_RSP = (1<<3),
AOEFL_ERR = (1<<2),
diff --git a/drivers/block/aoe/aoenet.c b/drivers/block/aoe/aoenet.c
index 30de5b1c647..c6099ba9a4b 100644
--- a/drivers/block/aoe/aoenet.c
+++ b/drivers/block/aoe/aoenet.c
@@ -142,6 +142,8 @@ aoenet_rcv(struct sk_buff *skb, struct net_device *ifp, struct packet_type *pt,
aoecmd_cfg_rsp(skb);
break;
default:
+ if (h->cmd >= AOECMD_VEND_MIN)
+ break; /* don't complain about vendor commands */
printk(KERN_INFO "aoe: unknown cmd %d\n", h->cmd);
}
exit:
diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c
index 01e69383d9c..d2cb67b6117 100644
--- a/drivers/block/cciss.c
+++ b/drivers/block/cciss.c
@@ -3390,6 +3390,203 @@ static void free_hba(int i)
kfree(p);
}
+/* Send a message CDB to the firmware. */
+static __devinit int cciss_message(struct pci_dev *pdev, unsigned char opcode, unsigned char type)
+{
+ typedef struct {
+ CommandListHeader_struct CommandHeader;
+ RequestBlock_struct Request;
+ ErrDescriptor_struct ErrorDescriptor;
+ } Command;
+ static const size_t cmd_sz = sizeof(Command) + sizeof(ErrorInfo_struct);
+ Command *cmd;
+ dma_addr_t paddr64;
+ uint32_t paddr32, tag;
+ void __iomem *vaddr;
+ int i, err;
+
+ vaddr = ioremap_nocache(pci_resource_start(pdev, 0), pci_resource_len(pdev, 0));
+ if (vaddr == NULL)
+ return -ENOMEM;
+
+ /* The Inbound Post Queue only accepts 32-bit physical addresses for the
+ CCISS commands, so they must be allocated from the lower 4GiB of
+ memory. */
+ err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+ if (err) {
+ iounmap(vaddr);
+ return -ENOMEM;
+ }
+
+ cmd = pci_alloc_consistent(pdev, cmd_sz, &paddr64);
+ if (cmd == NULL) {
+ iounmap(vaddr);
+ return -ENOMEM;
+ }
+
+ /* This must fit, because of the 32-bit consistent DMA mask. Also,
+ although there's no guarantee, we assume that the address is at
+ least 4-byte aligned (most likely, it's page-aligned). */
+ paddr32 = paddr64;
+
+ cmd->CommandHeader.ReplyQueue = 0;
+ cmd->CommandHeader.SGList = 0;
+ cmd->CommandHeader.SGTotal = 0;
+ cmd->CommandHeader.Tag.lower = paddr32;
+ cmd->CommandHeader.Tag.upper = 0;
+ memset(&cmd->CommandHeader.LUN.LunAddrBytes, 0, 8);
+
+ cmd->Request.CDBLen = 16;
+ cmd->Request.Type.Type = TYPE_MSG;
+ cmd->Request.Type.Attribute = ATTR_HEADOFQUEUE;
+ cmd->Request.Type.Direction = XFER_NONE;
+ cmd->Request.Timeout = 0; /* Don't time out */
+ cmd->Request.CDB[0] = opcode;
+ cmd->Request.CDB[1] = type;
+ memset(&cmd->Request.CDB[2], 0, 14); /* the rest of the CDB is reserved */
+
+ cmd->ErrorDescriptor.Addr.lower = paddr32 + sizeof(Command);
+ cmd->ErrorDescriptor.Addr.upper = 0;
+ cmd->ErrorDescriptor.Len = sizeof(ErrorInfo_struct);
+
+ writel(paddr32, vaddr + SA5_REQUEST_PORT_OFFSET);
+
+ for (i = 0; i < 10; i++) {
+ tag = readl(vaddr + SA5_REPLY_PORT_OFFSET);
+ if ((tag & ~3) == paddr32)
+ break;
+ schedule_timeout_uninterruptible(HZ);
+ }
+
+ iounmap(vaddr);
+
+ /* we leak the DMA buffer here ... no choice since the controller could
+ still complete the command. */
+ if (i == 10) {
+ printk(KERN_ERR "cciss: controller message %02x:%02x timed out\n",
+ opcode, type);
+ return -ETIMEDOUT;
+ }
+
+ pci_free_consistent(pdev, cmd_sz, cmd, paddr64);
+
+ if (tag & 2) {
+ printk(KERN_ERR "cciss: controller message %02x:%02x failed\n",
+ opcode, type);
+ return -EIO;
+ }
+
+ printk(KERN_INFO "cciss: controller message %02x:%02x succeeded\n",
+ opcode, type);
+ return 0;
+}
+
+#define cciss_soft_reset_controller(p) cciss_message(p, 1, 0)
+#define cciss_noop(p) cciss_message(p, 3, 0)
+
+static __devinit int cciss_reset_msi(struct pci_dev *pdev)
+{
+/* the #defines are stolen from drivers/pci/msi.h. */
+#define msi_control_reg(base) (base + PCI_MSI_FLAGS)
+#define PCI_MSIX_FLAGS_ENABLE (1 << 15)
+
+ int pos;
+ u16 control = 0;
+
+ pos = pci_find_capability(pdev, PCI_CAP_ID_MSI);
+ if (pos) {
+ pci_read_config_word(pdev, msi_control_reg(pos), &control);
+ if (control & PCI_MSI_FLAGS_ENABLE) {
+ printk(KERN_INFO "cciss: resetting MSI\n");
+ pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSI_FLAGS_ENABLE);
+ }
+ }
+
+ pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX);
+ if (pos) {
+ pci_read_config_word(pdev, msi_control_reg(pos), &control);
+ if (control & PCI_MSIX_FLAGS_ENABLE) {
+ printk(KERN_INFO "cciss: resetting MSI-X\n");
+ pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSIX_FLAGS_ENABLE);
+ }
+ }
+
+ return 0;
+}
+
+/* This does a hard reset of the controller using PCI power management
+ * states. */
+static __devinit int cciss_hard_reset_controller(struct pci_dev *pdev)
+{
+ u16 pmcsr, saved_config_space[32];
+ int i, pos;
+
+ printk(KERN_INFO "cciss: using PCI PM to reset controller\n");
+
+ /* This is very nearly the same thing as
+
+ pci_save_state(pci_dev);
+ pci_set_power_state(pci_dev, PCI_D3hot);
+ pci_set_power_state(pci_dev, PCI_D0);
+ pci_restore_state(pci_dev);
+
+ but we can't use these nice canned kernel routines on
+ kexec, because they also check the MSI/MSI-X state in PCI
+ configuration space and do the wrong thing when it is
+ set/cleared. Also, the pci_save/restore_state functions
+ violate the ordering requirements for restoring the
+ configuration space from the CCISS document (see the
+ comment below). So we roll our own .... */
+
+ for (i = 0; i < 32; i++)
+ pci_read_config_word(pdev, 2*i, &saved_config_space[i]);
+
+ pos = pci_find_capability(pdev, PCI_CAP_ID_PM);
+ if (pos == 0) {
+ printk(KERN_ERR "cciss_reset_controller: PCI PM not supported\n");
+ return -ENODEV;
+ }
+
+ /* Quoting from the Open CISS Specification: "The Power
+ * Management Control/Status Register (CSR) controls the power
+ * state of the device. The normal operating state is D0,
+ * CSR=00h. The software off state is D3, CSR=03h. To reset
+ * the controller, place the interface device in D3 then to
+ * D0, this causes a secondary PCI reset which will reset the
+ * controller." */
+
+ /* enter the D3hot power management state */
+ pci_read_config_word(pdev, pos + PCI_PM_CTRL, &pmcsr);
+ pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
+ pmcsr |= PCI_D3hot;
+ pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+
+ schedule_timeout_uninterruptible(HZ >> 1);
+
+ /* enter the D0 power management state */
+ pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
+ pmcsr |= PCI_D0;
+ pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+
+ schedule_timeout_uninterruptible(HZ >> 1);
+
+ /* Restore the PCI configuration space. The Open CISS
+ * Specification says, "Restore the PCI Configuration
+ * Registers, offsets 00h through 60h. It is important to
+ * restore the command register, 16-bits at offset 04h,
+ * last. Do not restore the configuration status register,
+ * 16-bits at offset 06h." Note that the offset is 2*i. */
+ for (i = 0; i < 32; i++) {
+ if (i == 2 || i == 3)
+ continue;
+ pci_write_config_word(pdev, 2*i, saved_config_space[i]);
+ }
+ wmb();
+ pci_write_config_word(pdev, 4, saved_config_space[2]);
+
+ return 0;
+}
+
/*
* This is it. Find all the controllers and register them. I really hate
* stealing all these major device numbers.
@@ -3404,6 +3601,24 @@ static int __devinit cciss_init_one(struct pci_dev *pdev,
int dac, return_code;
InquiryData_struct *inq_buff = NULL;
+ if (reset_devices) {
+ /* Reset the controller with a PCI power-cycle */
+ if (cciss_hard_reset_controller(pdev) || cciss_reset_msi(pdev))
+ return -ENODEV;
+
+ /* Some devices (notably the HP Smart Array 5i Controller)
+ need a little pause here */
+ schedule_timeout_uninterruptible(30*HZ);
+
+ /* Now try to get the controller to respond to a no-op */
+ for (i=0; i<12; i++) {
+ if (cciss_noop(pdev) == 0)
+ break;
+ else
+ printk("cciss: no-op failed%s\n", (i < 11 ? "; re-trying" : ""));
+ }
+ }
+
i = alloc_cciss_hba();
if (i < 0)
return -1;
diff --git a/drivers/block/floppy.c b/drivers/block/floppy.c
index cf29cc4e6ab..83d8ed39433 100644
--- a/drivers/block/floppy.c
+++ b/drivers/block/floppy.c
@@ -558,6 +558,8 @@ static void process_fd_request(void);
static void recalibrate_floppy(void);
static void floppy_shutdown(unsigned long);
+static int floppy_request_regions(int);
+static void floppy_release_regions(int);
static int floppy_grab_irq_and_dma(void);
static void floppy_release_irq_and_dma(void);
@@ -4274,8 +4276,7 @@ static int __init floppy_init(void)
FDCS->rawcmd = 2;
if (user_reset_fdc(-1, FD_RESET_ALWAYS, 0)) {
/* free ioports reserved by floppy_grab_irq_and_dma() */
- release_region(FDCS->address + 2, 4);
- release_region(FDCS->address + 7, 1);
+ floppy_release_regions(fdc);
FDCS->address = -1;
FDCS->version = FDC_NONE;
continue;
@@ -4284,8 +4285,7 @@ static int __init floppy_init(void)
FDCS->version = get_fdc_version();
if (FDCS->version == FDC_NONE) {
/* free ioports reserved by floppy_grab_irq_and_dma() */
- release_region(FDCS->address + 2, 4);
- release_region(FDCS->address + 7, 1);
+ floppy_release_regions(fdc);
FDCS->address = -1;
continue;
}
@@ -4358,6 +4358,47 @@ out_put_disk:
static DEFINE_SPINLOCK(floppy_usage_lock);
+static const struct io_region {
+ int offset;
+ int size;
+} io_regions[] = {
+ { 2, 1 },
+ /* address + 3 is sometimes reserved by pnp bios for motherboard */
+ { 4, 2 },
+ /* address + 6 is reserved, and may be taken by IDE.
+ * Unfortunately, Adaptec doesn't know this :-(, */
+ { 7, 1 },
+};
+
+static void floppy_release_allocated_regions(int fdc, const struct io_region *p)
+{
+ while (p != io_regions) {
+ p--;
+ release_region(FDCS->address + p->offset, p->size);
+ }
+}
+
+#define ARRAY_END(X) (&((X)[ARRAY_SIZE(X)]))
+
+static int floppy_request_regions(int fdc)
+{
+ const struct io_region *p;
+
+ for (p = io_regions; p < ARRAY_END(io_regions); p++) {
+ if (!request_region(FDCS->address + p->offset, p->size, "floppy")) {
+ DPRINT("Floppy io-port 0x%04lx in use\n", FDCS->address + p->offset);
+ floppy_release_allocated_regions(fdc, p);
+ return -EBUSY;
+ }
+ }
+ return 0;
+}
+
+static void floppy_release_regions(int fdc)
+{
+ floppy_release_allocated_regions(fdc, ARRAY_END(io_regions));
+}
+
static int floppy_grab_irq_and_dma(void)
{
unsigned long flags;
@@ -4399,18 +4440,8 @@ static int floppy_grab_irq_and_dma(void)
for (fdc = 0; fdc < N_FDC; fdc++) {
if (FDCS->address != -1) {
- if (!request_region(FDCS->address + 2, 4, "floppy")) {
- DPRINT("Floppy io-port 0x%04lx in use\n",
- FDCS->address + 2);
- goto cleanup1;
- }
- if (!request_region(FDCS->address + 7, 1, "floppy DIR")) {
- DPRINT("Floppy io-port 0x%04lx in use\n",
- FDCS->address + 7);
- goto cleanup2;
- }
- /* address + 6 is reserved, and may be taken by IDE.
- * Unfortunately, Adaptec doesn't know this :-(, */
+ if (floppy_request_regions(fdc))
+ goto cleanup;
}
}
for (fdc = 0; fdc < N_FDC; fdc++) {
@@ -4432,15 +4463,11 @@ static int floppy_grab_irq_and_dma(void)
fdc = 0;
irqdma_allocated = 1;
return 0;
-cleanup2:
- release_region(FDCS->address + 2, 4);
-cleanup1:
+cleanup:
fd_free_irq();
fd_free_dma();
- while (--fdc >= 0) {
- release_region(FDCS->address + 2, 4);
- release_region(FDCS->address + 7, 1);
- }
+ while (--fdc >= 0)
+ floppy_release_regions(fdc);
spin_lock_irqsave(&floppy_usage_lock, flags);
usage_count--;
spin_unlock_irqrestore(&floppy_usage_lock, flags);
@@ -4501,10 +4528,8 @@ static void floppy_release_irq_and_dma(void)
#endif
old_fdc = fdc;
for (fdc = 0; fdc < N_FDC; fdc++)
- if (FDCS->address != -1) {
- release_region(FDCS->address + 2, 4);
- release_region(FDCS->address + 7, 1);
- }
+ if (FDCS->address != -1)
+ floppy_release_regions(fdc);
fdc = old_fdc;
}
diff --git a/drivers/block/paride/pg.c b/drivers/block/paride/pg.c
index 9dfa2716300..c397b3ddba9 100644
--- a/drivers/block/paride/pg.c
+++ b/drivers/block/paride/pg.c
@@ -422,7 +422,7 @@ static void xs(char *buf, char *targ, int len)
for (k = 0; k < len; k++) {
char c = *buf++;
- if (c != ' ' || c != l)
+ if (c != ' ' && c != l)
l = *targ++ = c;
}
if (l == ' ')
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-02 23:56:11 +0000