aboutsummaryrefslogtreecommitdiff
path: root/drivers/char/ftape/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/char/ftape/Kconfig')
-rw-r--r--drivers/char/ftape/Kconfig340
1 files changed, 340 insertions, 0 deletions
diff --git a/drivers/char/ftape/Kconfig b/drivers/char/ftape/Kconfig
new file mode 100644
index 00000000000..7d3ecb56a1b
--- /dev/null
+++ b/drivers/char/ftape/Kconfig
@@ -0,0 +1,340 @@
+#
+# Ftape configuration
+#
+config ZFTAPE
+ tristate "Zftape, the VFS interface"
+ depends on FTAPE
+ ---help---
+ Normally, you want to say Y or M. DON'T say N here or you
+ WON'T BE ABLE TO USE YOUR FLOPPY TAPE DRIVE.
+
+ The ftape module itself no longer contains the routines necessary
+ to interface with the kernel VFS layer (i.e. to actually write data
+ to and read data from the tape drive). Instead the file system
+ interface (i.e. the hardware independent part of the driver) has
+ been moved to a separate module.
+
+ To compile this driver as a module, choose M here: the
+ module will be called zftape.
+
+ Regardless of whether you say Y or M here, an additional runtime
+ loadable module called `zft-compressor' which contains code to
+ support user transparent on-the-fly compression based on Ross
+ William's lzrw3 algorithm will be produced. If you have enabled the
+ kernel module loader (i.e. have said Y to "Kernel module loader
+ support", above) then `zft-compressor' will be loaded
+ automatically by zftape when needed.
+
+ Despite its name, zftape does NOT use compression by default. The
+ file <file:Documentation/ftape.txt> contains a short description of
+ the most important changes in the file system interface compared to
+ previous versions of ftape. The ftape home page
+ <http://www.instmath.rwth-aachen.de/~heine/ftape/> contains
+ further information.
+
+ IMPORTANT NOTE: zftape can read archives created by previous
+ versions of ftape and provide file mark support (i.e. fast skipping
+ between tape archives) but previous version of ftape will lack file
+ mark support when reading archives produced by zftape.
+
+config ZFT_DFLT_BLK_SZ
+ int "Default block size"
+ depends on ZFTAPE
+ default "10240"
+ ---help---
+ If unsure leave this at its default value, i.e. 10240. Note that
+ you specify only the default block size here. The block size can be
+ changed at run time using the MTSETBLK tape operation with the
+ MTIOCTOP ioctl (i.e. with "mt -f /dev/qft0 setblk #BLKSZ" from the
+ shell command line).
+
+ The probably most striking difference between zftape and previous
+ versions of ftape is the fact that all data must be written or read
+ in multiples of a fixed block size. The block size defaults to
+ 10240 which is what GNU tar uses. The values for the block size
+ should be either 1 or multiples of 1024 up to a maximum value of
+ 63488 (i.e. 62 K). If you specify `1' then zftape's builtin
+ compression will be disabled.
+
+ Reasonable values are `10240' (GNU tar's default block size),
+ `5120' (afio's default block size), `32768' (default block size some
+ backup programs assume for SCSI tape drives) or `1' (no restriction
+ on block size, but disables builtin compression).
+
+comment "The compressor will be built as a module only!"
+ depends on FTAPE && ZFTAPE
+
+config ZFT_COMPRESSOR
+ tristate
+ depends on FTAPE!=n && ZFTAPE!=n
+ default m
+
+config FT_NR_BUFFERS
+ int "Number of ftape buffers (EXPERIMENTAL)"
+ depends on FTAPE && EXPERIMENTAL
+ default "3"
+ help
+ Please leave this at `3' unless you REALLY know what you are doing.
+ It is not necessary to change this value. Values below 3 make the
+ proper use of ftape impossible, values greater than 3 are a waste of
+ memory. You can change the amount of DMA memory used by ftape at
+ runtime with "mt -f /dev/qft0 setdrvbuffer #NUMBUFFERS". Each buffer
+ wastes 32 KB of memory. Please note that this memory cannot be
+ swapped out.
+
+config FT_PROC_FS
+ bool "Enable procfs status report (+2kb)"
+ depends on FTAPE && PROC_FS
+ ---help---
+ Optional. Saying Y will result in creation of a directory
+ `/proc/ftape' under the /proc file system. The files can be viewed
+ with your favorite pager (i.e. use "more /proc/ftape/history" or
+ "less /proc/ftape/history" or simply "cat /proc/ftape/history"). The
+ file will contain some status information about the inserted
+ cartridge, the kernel driver, your tape drive, the floppy disk
+ controller and the error history for the most recent use of the
+ kernel driver. Saying Y will enlarge the size of the ftape driver
+ by approximately 2 KB.
+
+ WARNING: When compiling ftape as a module (i.e. saying M to "Floppy
+ tape drive") it is dangerous to use ftape's /proc file system
+ interface. Accessing `/proc/ftape' while the module is unloaded will
+ result in a kernel Oops. This cannot be fixed from inside ftape.
+
+choice
+ prompt "Debugging output"
+ depends on FTAPE
+ default FT_NORMAL_DEBUG
+
+config FT_NORMAL_DEBUG
+ bool "Normal"
+ ---help---
+ This option controls the amount of debugging output the ftape driver
+ is ABLE to produce; it does not increase or diminish the debugging
+ level itself. If unsure, leave this at its default setting,
+ i.e. choose "Normal".
+
+ Ftape can print lots of debugging messages to the system console
+ resp. kernel log files. Reducing the amount of possible debugging
+ output reduces the size of the kernel module by some KB, so it might
+ be a good idea to use "None" for emergency boot floppies.
+
+ If you want to save memory then the following strategy is
+ recommended: leave this option at its default setting "Normal" until
+ you know that the driver works as expected, afterwards reconfigure
+ the kernel, this time specifying "Reduced" or "None" and recompile
+ and install the kernel as usual. Note that choosing "Excessive"
+ debugging output does not increase the amount of debugging output
+ printed to the console but only makes it possible to produce
+ "Excessive" debugging output.
+
+ Please read <file:Documentation/ftape.txt> for a short description
+ how to control the amount of debugging output.
+
+config FT_FULL_DEBUG
+ bool "Excessive"
+ help
+ Extremely verbose output for driver debugging purposes.
+
+config FT_NO_TRACE
+ bool "Reduced"
+ help
+ Reduced tape driver debugging output.
+
+config FT_NO_TRACE_AT_ALL
+ bool "None"
+ help
+ Suppress all debugging output from the tape drive.
+
+endchoice
+
+comment "Hardware configuration"
+ depends on FTAPE
+
+choice
+ prompt "Floppy tape controllers"
+ depends on FTAPE
+ default FT_STD_FDC
+
+config FT_STD_FDC
+ bool "Standard"
+ ---help---
+ Only change this setting if you have a special controller. If you
+ didn't plug any add-on card into your computer system but just
+ plugged the floppy tape cable into the already existing floppy drive
+ controller then you don't want to change the default setting,
+ i.e. choose "Standard".
+
+ Choose "MACH-2" if you have a Mountain Mach-2 controller.
+ Choose "FC-10/FC-20" if you have a Colorado FC-10 or FC-20
+ controller.
+ Choose "Alt/82078" if you have another controller that is located at
+ an IO base address different from the standard floppy drive
+ controller's base address of `0x3f0', or uses an IRQ (interrupt)
+ channel different from `6', or a DMA channel different from
+ `2'. This is necessary for any controller card that is based on
+ Intel's 82078 FDC such as Seagate's, Exabyte's and Iomega's "high
+ speed" controllers.
+
+ If you choose something other than "Standard" then please make
+ sure that the settings for the IO base address and the IRQ and DMA
+ channel in the configuration menus below are correct. Use the manual
+ of your tape drive to determine the correct settings!
+
+ If you are already successfully using your tape drive with another
+ operating system then you definitely should use the same settings
+ for the IO base, the IRQ and DMA channel that have proven to work
+ with that other OS.
+
+ Note that this menu lets you specify only the default setting for
+ the hardware setup. The hardware configuration can be changed at
+ boot time (when ftape is compiled into the kernel, i.e. if you
+ have said Y to "Floppy tape drive") or module load time (i.e. if you
+ have said M to "Floppy tape drive").
+
+ Please read also the file <file:Documentation/ftape.txt> which
+ contains a short description of the parameters that can be set at
+ boot or load time. If you want to use your floppy tape drive on a
+ PCI-bus based system, please read the file
+ <file:drivers/char/ftape/README.PCI>.
+
+config FT_MACH2
+ bool "MACH-2"
+
+config FT_PROBE_FC10
+ bool "FC-10/FC-20"
+
+config FT_ALT_FDC
+ bool "Alt/82078"
+
+endchoice
+
+comment "Consult the manuals of your tape drive for the correct settings!"
+ depends on FTAPE && !FT_STD_FDC
+
+config FT_FDC_BASE
+ hex "IO base of the floppy disk controller"
+ depends on FTAPE && !FT_STD_FDC
+ default "0"
+ ---help---
+ You don't need to specify a value if the following default
+ settings for the base IO address are correct:
+ <<< MACH-2 : 0x1E0 >>>
+ <<< FC-10/FC-20: 0x180 >>>
+ <<< Secondary : 0x370 >>>
+ Secondary refers to a secondary FDC controller like the "high speed"
+ controllers delivered by Seagate or Exabyte or Iomega's Ditto Dash.
+ Please make sure that the setting for the IO base address
+ specified here is correct. USE THE MANUAL OF YOUR TAPE DRIVE OR
+ CONTROLLER CARD TO DETERMINE THE CORRECT SETTING. If you are already
+ successfully using the tape drive with another operating system then
+ you definitely should use the same settings for the IO base that has
+ proven to work with that other OS.
+
+ Note that this menu lets you specify only the default setting for
+ the IO base. The hardware configuration can be changed at boot time
+ (when ftape is compiled into the kernel, i.e. if you specified Y to
+ "Floppy tape drive") or module load time (i.e. if you have said M to
+ "Floppy tape drive").
+
+ Please read also the file <file:Documentation/ftape.txt> which
+ contains a short description of the parameters that can be set at
+ boot or load time.
+
+config FT_FDC_IRQ
+ int "IRQ channel of the floppy disk controller"
+ depends on FTAPE && !FT_STD_FDC
+ default "0"
+ ---help---
+ You don't need to specify a value if the following default
+ settings for the interrupt channel are correct:
+ <<< MACH-2 : 6 >>>
+ <<< FC-10/FC-20: 9 >>>
+ <<< Secondary : 6 >>>
+ Secondary refers to secondary a FDC controller like the "high speed"
+ controllers delivered by Seagate or Exabyte or Iomega's Ditto Dash.
+ Please make sure that the setting for the IO base address
+ specified here is correct. USE THE MANUAL OF YOUR TAPE DRIVE OR
+ CONTROLLER CARD TO DETERMINE THE CORRECT SETTING. If you are already
+ successfully using the tape drive with another operating system then
+ you definitely should use the same settings for the IO base that has
+ proven to work with that other OS.
+
+ Note that this menu lets you specify only the default setting for
+ the IRQ channel. The hardware configuration can be changed at boot
+ time (when ftape is compiled into the kernel, i.e. if you said Y to
+ "Floppy tape drive") or module load time (i.e. if you said M to
+ "Floppy tape drive").
+
+ Please read also the file <file:Documentation/ftape.txt> which
+ contains a short description of the parameters that can be set at
+ boot or load time.
+
+config FT_FDC_DMA
+ int "DMA channel of the floppy disk controller"
+ depends on FTAPE && !FT_STD_FDC
+ default "0"
+ ---help---
+ You don't need to specify a value if the following default
+ settings for the DMA channel are correct:
+ <<< MACH-2 : 2 >>>
+ <<< FC-10/FC-20: 3 >>>
+ <<< Secondary : 2 >>>
+ Secondary refers to a secondary FDC controller like the "high speed"
+ controllers delivered by Seagate or Exabyte or Iomega's Ditto Dash.
+ Please make sure that the setting for the IO base address
+ specified here is correct. USE THE MANUAL OF YOUR TAPE DRIVE OR
+ CONTROLLER CARD TO DETERMINE THE CORRECT SETTING. If you are already
+ successfully using the tape drive with another operating system then
+ you definitely should use the same settings for the IO base that has
+ proven to work with that other OS.
+
+ Note that this menu lets you specify only the default setting for
+ the DMA channel. The hardware configuration can be changed at boot
+ time (when ftape is compiled into the kernel, i.e. if you said Y to
+ "Floppy tape drive") or module load time (i.e. if you said M to
+ "Floppy tape drive").
+
+ Please read also the file <file:Documentation/ftape.txt> which
+ contains a short description of the parameters that can be set at
+ boot or load time.
+
+config FT_FDC_THR
+ int "Default FIFO threshold (EXPERIMENTAL)"
+ depends on FTAPE && EXPERIMENTAL
+ default "8"
+ help
+ Set the FIFO threshold of the FDC. If this is higher the DMA
+ controller may serve the FDC after a higher latency time. If this is
+ lower, fewer DMA transfers occur leading to less bus contention.
+ You may try to tune this if ftape annoys you with "reduced data
+ rate because of excessive overrun errors" messages. However, this
+ doesn't seem to have too much effect.
+
+ If unsure, don't touch the initial value, i.e. leave it at "8".
+
+config FT_FDC_MAX_RATE
+ int "Maximal data rate to use (EXPERIMENTAL)"
+ depends on FTAPE && EXPERIMENTAL
+ default "2000"
+ ---help---
+ With some motherboard/FDC combinations ftape will not be able to
+ run your FDC/tape drive combination at the highest available
+ speed. If this is the case you'll encounter "reduced data rate
+ because of excessive overrun errors" messages and lots of retries
+ before ftape finally decides to reduce the data rate.
+
+ In this case it might be desirable to tell ftape beforehand that
+ it need not try to run the tape drive at the highest available
+ speed. If unsure, leave this disabled, i.e. leave it at 2000
+ bits/sec.
+
+config FT_ALPHA_CLOCK
+ int "CPU clock frequency of your DEC Alpha" if ALPHA
+ depends on FTAPE
+ default "0"
+ help
+ On some DEC Alpha machines the CPU clock frequency cannot be
+ determined automatically, so you need to specify it here ONLY if
+ running a DEC Alpha, otherwise this setting has no effect.
+