aboutsummaryrefslogtreecommitdiff
path: root/drivers/macintosh/macserial.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/macintosh/macserial.h')
-rw-r--r--drivers/macintosh/macserial.h461
1 files changed, 461 insertions, 0 deletions
diff --git a/drivers/macintosh/macserial.h b/drivers/macintosh/macserial.h
new file mode 100644
index 00000000000..bade11a7a5c
--- /dev/null
+++ b/drivers/macintosh/macserial.h
@@ -0,0 +1,461 @@
+/*
+ * macserial.h: Definitions for the Macintosh Z8530 serial driver.
+ *
+ * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
+ *
+ * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ */
+#ifndef _MACSERIAL_H
+#define _MACSERIAL_H
+
+#include <linux/spinlock.h>
+
+#define NUM_ZSREGS 16
+
+struct serial_struct {
+ int type;
+ int line;
+ int port;
+ int irq;
+ int flags;
+ int xmit_fifo_size;
+ int custom_divisor;
+ int baud_base;
+ unsigned short close_delay;
+ char reserved_char[2];
+ int hub6;
+ unsigned short closing_wait; /* time to wait before closing */
+ unsigned short closing_wait2; /* no longer used... */
+ int reserved[4];
+};
+
+/*
+ * For the close wait times, 0 means wait forever for serial port to
+ * flush its output. 65535 means don't wait at all.
+ */
+#define ZILOG_CLOSING_WAIT_INF 0
+#define ZILOG_CLOSING_WAIT_NONE 65535
+
+/*
+ * Definitions for ZILOG_struct (and serial_struct) flags field
+ */
+#define ZILOG_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes
+ * on the callout port */
+#define ZILOG_FOURPORT 0x0002 /* Set OU1, OUT2 per AST Fourport settings */
+#define ZILOG_SAK 0x0004 /* Secure Attention Key (Orange book) */
+#define ZILOG_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */
+
+#define ZILOG_SPD_MASK 0x0030
+#define ZILOG_SPD_HI 0x0010 /* Use 56000 instead of 38400 bps */
+
+#define ZILOG_SPD_VHI 0x0020 /* Use 115200 instead of 38400 bps */
+#define ZILOG_SPD_CUST 0x0030 /* Use user-specified divisor */
+
+#define ZILOG_SKIP_TEST 0x0040 /* Skip UART test during autoconfiguration */
+#define ZILOG_AUTO_IRQ 0x0080 /* Do automatic IRQ during autoconfiguration */
+#define ZILOG_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
+#define ZILOG_PGRP_LOCKOUT 0x0200 /* Lock out cua opens based on pgrp */
+#define ZILOG_CALLOUT_NOHUP 0x0400 /* Don't do hangups for cua device */
+
+#define ZILOG_FLAGS 0x0FFF /* Possible legal ZILOG flags */
+#define ZILOG_USR_MASK 0x0430 /* Legal flags that non-privileged
+ * users can set or reset */
+
+/* Internal flags used only by kernel/chr_drv/serial.c */
+#define ZILOG_INITIALIZED 0x80000000 /* Serial port was initialized */
+#define ZILOG_CALLOUT_ACTIVE 0x40000000 /* Call out device is active */
+#define ZILOG_NORMAL_ACTIVE 0x20000000 /* Normal device is active */
+#define ZILOG_BOOT_AUTOCONF 0x10000000 /* Autoconfigure port on bootup */
+#define ZILOG_CLOSING 0x08000000 /* Serial port is closing */
+#define ZILOG_CTS_FLOW 0x04000000 /* Do CTS flow control */
+#define ZILOG_CHECK_CD 0x02000000 /* i.e., CLOCAL */
+#define ZILOG_SLEEPING 0x01000000 /* have shut it down for sleep */
+
+/* Software state per channel */
+
+#ifdef __KERNEL__
+/*
+ * This is our internal structure for each serial port's state.
+ *
+ * Many fields are paralleled by the structure used by the serial_struct
+ * structure.
+ *
+ * For definitions of the flags field, see tty.h
+ */
+
+struct mac_serial;
+
+struct mac_zschannel {
+ volatile unsigned char* control;
+ volatile unsigned char* data;
+ spinlock_t lock;
+ /* Used for debugging */
+ struct mac_serial* parent;
+};
+
+struct mac_dma {
+ volatile struct dbdma_regs dma;
+ volatile unsigned short res_count;
+ volatile unsigned short command;
+ volatile unsigned int buf_addr;
+};
+
+struct mac_serial {
+ struct mac_serial *zs_next; /* For IRQ servicing chain */
+ struct mac_zschannel *zs_channel; /* Channel registers */
+ struct mac_zschannel *zs_chan_a; /* A side registers */
+ unsigned char read_reg_zero;
+ struct device_node* dev_node;
+ spinlock_t lock;
+
+ char soft_carrier; /* Use soft carrier on this channel */
+ char break_abort; /* Is serial console in, so process brk/abrt */
+ char kgdb_channel; /* Kgdb is running on this channel */
+ char is_cons; /* Is this our console. */
+ char is_internal_modem; /* is connected to an internal modem */
+ char is_irda; /* is connected to an IrDA codec */
+ int port_type; /* Port type for pmac_feature */
+ unsigned char tx_active; /* character is being xmitted */
+ unsigned char tx_stopped; /* output is suspended */
+ unsigned char power_wait; /* waiting for power-up delay to expire */
+
+ /* We need to know the current clock divisor
+ * to read the bps rate the chip has currently
+ * loaded.
+ */
+ unsigned char clk_divisor; /* May be 1, 16, 32, or 64 */
+ int zs_baud;
+
+ /* Current write register values */
+ unsigned char curregs[NUM_ZSREGS];
+
+ /* Values we need to set next opportunity */
+ unsigned char pendregs[NUM_ZSREGS];
+
+ char change_needed;
+
+ int magic;
+ int baud_base;
+ int port;
+ int irq;
+ int flags; /* defined in tty.h */
+ int type; /* UART type */
+ struct tty_struct *tty;
+ int read_status_mask;
+ int ignore_status_mask;
+ int timeout;
+ int xmit_fifo_size;
+ int custom_divisor;
+ int x_char; /* xon/xoff character */
+ int close_delay;
+ unsigned short closing_wait;
+ unsigned short closing_wait2;
+ unsigned long event;
+ unsigned long last_active;
+ int line;
+ int count; /* # of fd on device */
+ int blocked_open; /* # of blocked opens */
+ unsigned char *xmit_buf;
+ int xmit_head;
+ int xmit_tail;
+ int xmit_cnt;
+ struct work_struct tqueue;
+ wait_queue_head_t open_wait;
+ wait_queue_head_t close_wait;
+
+ volatile struct dbdma_regs *tx_dma;
+ int tx_dma_irq;
+ volatile struct dbdma_cmd *tx_cmds;
+ volatile struct mac_dma *rx;
+ int rx_dma_irq;
+ volatile struct dbdma_cmd **rx_cmds;
+ unsigned char **rx_char_buf;
+ unsigned char **rx_flag_buf;
+#define RX_BUF_SIZE 256
+ int rx_nbuf;
+ int rx_done_bytes;
+ int rx_ubuf;
+ int rx_fbuf;
+#define RX_NO_FBUF (-1)
+ int rx_cbuf;
+ spinlock_t rx_dma_lock;
+ int has_dma;
+ int dma_initted;
+ void *dma_priv;
+ struct timer_list poll_dma_timer;
+#define RX_DMA_TIMER (jiffies + 10*HZ/1000)
+
+ struct timer_list powerup_timer;
+};
+
+
+#define SERIAL_MAGIC 0x5301
+
+/*
+ * The size of the serial xmit buffer is 1 page, or 4096 bytes
+ */
+#define SERIAL_XMIT_SIZE 4096
+
+/*
+ * Events are used to schedule things to happen at timer-interrupt
+ * time, instead of at rs interrupt time.
+ */
+#define RS_EVENT_WRITE_WAKEUP 0
+
+#endif /* __KERNEL__ */
+
+/* Conversion routines to/from brg time constants from/to bits
+ * per second.
+ */
+#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
+#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
+
+/* The Zilog register set */
+
+#define FLAG 0x7e
+
+/* Write Register 0 */
+#define R0 0 /* Register selects */
+#define R1 1
+#define R2 2
+#define R3 3
+#define R4 4
+#define R5 5
+#define R6 6
+#define R7 7
+#define R8 8
+#define R9 9
+#define R10 10
+#define R11 11
+#define R12 12
+#define R13 13
+#define R14 14
+#define R15 15
+
+#define NULLCODE 0 /* Null Code */
+#define POINT_HIGH 0x8 /* Select upper half of registers */
+#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
+#define SEND_ABORT 0x18 /* HDLC Abort */
+#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
+#define RES_Tx_P 0x28 /* Reset TxINT Pending */
+#define ERR_RES 0x30 /* Error Reset */
+#define RES_H_IUS 0x38 /* Reset highest IUS */
+
+#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
+#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
+#define RES_EOM_L 0xC0 /* Reset EOM latch */
+
+/* Write Register 1 */
+
+#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
+#define TxINT_ENAB 0x2 /* Tx Int Enable */
+#define PAR_SPEC 0x4 /* Parity is special condition */
+
+#define RxINT_DISAB 0 /* Rx Int Disable */
+#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
+#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
+#define INT_ERR_Rx 0x18 /* Int on error only */
+
+#define WT_RDY_RT 0x20 /* W/Req reflects recv if 1, xmit if 0 */
+#define WT_FN_RDYFN 0x40 /* W/Req pin is DMA request if 1, wait if 0 */
+#define WT_RDY_ENAB 0x80 /* Enable W/Req pin */
+
+/* Write Register #2 (Interrupt Vector) */
+
+/* Write Register 3 */
+
+#define RxENABLE 0x1 /* Rx Enable */
+#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
+#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
+#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
+#define ENT_HM 0x10 /* Enter Hunt Mode */
+#define AUTO_ENAB 0x20 /* Auto Enables */
+#define Rx5 0x0 /* Rx 5 Bits/Character */
+#define Rx7 0x40 /* Rx 7 Bits/Character */
+#define Rx6 0x80 /* Rx 6 Bits/Character */
+#define Rx8 0xc0 /* Rx 8 Bits/Character */
+#define RxNBITS_MASK 0xc0
+
+/* Write Register 4 */
+
+#define PAR_ENA 0x1 /* Parity Enable */
+#define PAR_EVEN 0x2 /* Parity Even/Odd* */
+
+#define SYNC_ENAB 0 /* Sync Modes Enable */
+#define SB1 0x4 /* 1 stop bit/char */
+#define SB15 0x8 /* 1.5 stop bits/char */
+#define SB2 0xc /* 2 stop bits/char */
+#define SB_MASK 0xc
+
+#define MONSYNC 0 /* 8 Bit Sync character */
+#define BISYNC 0x10 /* 16 bit sync character */
+#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
+#define EXTSYNC 0x30 /* External Sync Mode */
+
+#define X1CLK 0x0 /* x1 clock mode */
+#define X16CLK 0x40 /* x16 clock mode */
+#define X32CLK 0x80 /* x32 clock mode */
+#define X64CLK 0xC0 /* x64 clock mode */
+#define XCLK_MASK 0xC0
+
+/* Write Register 5 */
+
+#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
+#define RTS 0x2 /* RTS */
+#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
+#define TxENAB 0x8 /* Tx Enable */
+#define SND_BRK 0x10 /* Send Break */
+#define Tx5 0x0 /* Tx 5 bits (or less)/character */
+#define Tx7 0x20 /* Tx 7 bits/character */
+#define Tx6 0x40 /* Tx 6 bits/character */
+#define Tx8 0x60 /* Tx 8 bits/character */
+#define TxNBITS_MASK 0x60
+#define DTR 0x80 /* DTR */
+
+/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
+
+/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
+
+/* Write Register 7' (Some enhanced feature control) */
+#define ENEXREAD 0x40 /* Enable read of some write registers */
+
+/* Write Register 8 (transmit buffer) */
+
+/* Write Register 9 (Master interrupt control) */
+#define VIS 1 /* Vector Includes Status */
+#define NV 2 /* No Vector */
+#define DLC 4 /* Disable Lower Chain */
+#define MIE 8 /* Master Interrupt Enable */
+#define STATHI 0x10 /* Status high */
+#define NORESET 0 /* No reset on write to R9 */
+#define CHRB 0x40 /* Reset channel B */
+#define CHRA 0x80 /* Reset channel A */
+#define FHWRES 0xc0 /* Force hardware reset */
+
+/* Write Register 10 (misc control bits) */
+#define BIT6 1 /* 6 bit/8bit sync */
+#define LOOPMODE 2 /* SDLC Loop mode */
+#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
+#define MARKIDLE 8 /* Mark/flag on idle */
+#define GAOP 0x10 /* Go active on poll */
+#define NRZ 0 /* NRZ mode */
+#define NRZI 0x20 /* NRZI mode */
+#define FM1 0x40 /* FM1 (transition = 1) */
+#define FM0 0x60 /* FM0 (transition = 0) */
+#define CRCPS 0x80 /* CRC Preset I/O */
+
+/* Write Register 11 (Clock Mode control) */
+#define TRxCXT 0 /* TRxC = Xtal output */
+#define TRxCTC 1 /* TRxC = Transmit clock */
+#define TRxCBR 2 /* TRxC = BR Generator Output */
+#define TRxCDP 3 /* TRxC = DPLL output */
+#define TRxCOI 4 /* TRxC O/I */
+#define TCRTxCP 0 /* Transmit clock = RTxC pin */
+#define TCTRxCP 8 /* Transmit clock = TRxC pin */
+#define TCBR 0x10 /* Transmit clock = BR Generator output */
+#define TCDPLL 0x18 /* Transmit clock = DPLL output */
+#define RCRTxCP 0 /* Receive clock = RTxC pin */
+#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
+#define RCBR 0x40 /* Receive clock = BR Generator output */
+#define RCDPLL 0x60 /* Receive clock = DPLL output */
+#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
+
+/* Write Register 12 (lower byte of baud rate generator time constant) */
+
+/* Write Register 13 (upper byte of baud rate generator time constant) */
+
+/* Write Register 14 (Misc control bits) */
+#define BRENABL 1 /* Baud rate generator enable */
+#define BRSRC 2 /* Baud rate generator source */
+#define DTRREQ 4 /* DTR/Request function */
+#define AUTOECHO 8 /* Auto Echo */
+#define LOOPBAK 0x10 /* Local loopback */
+#define SEARCH 0x20 /* Enter search mode */
+#define RMC 0x40 /* Reset missing clock */
+#define DISDPLL 0x60 /* Disable DPLL */
+#define SSBR 0x80 /* Set DPLL source = BR generator */
+#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
+#define SFMM 0xc0 /* Set FM mode */
+#define SNRZI 0xe0 /* Set NRZI mode */
+
+/* Write Register 15 (external/status interrupt control) */
+#define EN85C30 1 /* Enable some 85c30-enhanced registers */
+#define ZCIE 2 /* Zero count IE */
+#define ENSTFIFO 4 /* Enable status FIFO (SDLC) */
+#define DCDIE 8 /* DCD IE */
+#define SYNCIE 0x10 /* Sync/hunt IE */
+#define CTSIE 0x20 /* CTS IE */
+#define TxUIE 0x40 /* Tx Underrun/EOM IE */
+#define BRKIE 0x80 /* Break/Abort IE */
+
+
+/* Read Register 0 */
+#define Rx_CH_AV 0x1 /* Rx Character Available */
+#define ZCOUNT 0x2 /* Zero count */
+#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
+#define DCD 0x8 /* DCD */
+#define SYNC_HUNT 0x10 /* Sync/hunt */
+#define CTS 0x20 /* CTS */
+#define TxEOM 0x40 /* Tx underrun */
+#define BRK_ABRT 0x80 /* Break/Abort */
+
+/* Read Register 1 */
+#define ALL_SNT 0x1 /* All sent */
+/* Residue Data for 8 Rx bits/char programmed */
+#define RES3 0x8 /* 0/3 */
+#define RES4 0x4 /* 0/4 */
+#define RES5 0xc /* 0/5 */
+#define RES6 0x2 /* 0/6 */
+#define RES7 0xa /* 0/7 */
+#define RES8 0x6 /* 0/8 */
+#define RES18 0xe /* 1/8 */
+#define RES28 0x0 /* 2/8 */
+/* Special Rx Condition Interrupts */
+#define PAR_ERR 0x10 /* Parity error */
+#define Rx_OVR 0x20 /* Rx Overrun Error */
+#define FRM_ERR 0x40 /* CRC/Framing Error */
+#define END_FR 0x80 /* End of Frame (SDLC) */
+
+/* Read Register 2 (channel b only) - Interrupt vector */
+#define CHB_Tx_EMPTY 0x00
+#define CHB_EXT_STAT 0x02
+#define CHB_Rx_AVAIL 0x04
+#define CHB_SPECIAL 0x06
+#define CHA_Tx_EMPTY 0x08
+#define CHA_EXT_STAT 0x0a
+#define CHA_Rx_AVAIL 0x0c
+#define CHA_SPECIAL 0x0e
+#define STATUS_MASK 0x06
+
+/* Read Register 3 (interrupt pending register) ch a only */
+#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
+#define CHBTxIP 0x2 /* Channel B Tx IP */
+#define CHBRxIP 0x4 /* Channel B Rx IP */
+#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
+#define CHATxIP 0x10 /* Channel A Tx IP */
+#define CHARxIP 0x20 /* Channel A Rx IP */
+
+/* Read Register 8 (receive data register) */
+
+/* Read Register 10 (misc status bits) */
+#define ONLOOP 2 /* On loop */
+#define LOOPSEND 0x10 /* Loop sending */
+#define CLK2MIS 0x40 /* Two clocks missing */
+#define CLK1MIS 0x80 /* One clock missing */
+
+/* Read Register 12 (lower byte of baud rate generator constant) */
+
+/* Read Register 13 (upper byte of baud rate generator constant) */
+
+/* Read Register 15 (value of WR 15) */
+
+/* Misc macros */
+#define ZS_CLEARERR(channel) (write_zsreg(channel, 0, ERR_RES))
+#define ZS_CLEARFIFO(channel) do { volatile unsigned char garbage; \
+ garbage = read_zsdata(channel); \
+ garbage = read_zsdata(channel); \
+ garbage = read_zsdata(channel); \
+ } while(0)
+
+#endif /* !(_MACSERIAL_H) */