aboutsummaryrefslogtreecommitdiff
path: root/drivers/macintosh/macserial.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/macintosh/macserial.h')
-rw-r--r--drivers/macintosh/macserial.h461
1 files changed, 0 insertions, 461 deletions
diff --git a/drivers/macintosh/macserial.h b/drivers/macintosh/macserial.h
deleted file mode 100644
index bade11a7a5c..00000000000
--- a/drivers/macintosh/macserial.h
+++ /dev/null
@@ -1,461 +0,0 @@
-/*
- * macserial.h: Definitions for the Macintosh Z8530 serial driver.
- *
- * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
- *
- * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- */
-#ifndef _MACSERIAL_H
-#define _MACSERIAL_H
-
-#include <linux/spinlock.h>
-
-#define NUM_ZSREGS 16
-
-struct serial_struct {
- int type;
- int line;
- int port;
- int irq;
- int flags;
- int xmit_fifo_size;
- int custom_divisor;
- int baud_base;
- unsigned short close_delay;
- char reserved_char[2];
- int hub6;
- unsigned short closing_wait; /* time to wait before closing */
- unsigned short closing_wait2; /* no longer used... */
- int reserved[4];
-};
-
-/*
- * For the close wait times, 0 means wait forever for serial port to
- * flush its output. 65535 means don't wait at all.
- */
-#define ZILOG_CLOSING_WAIT_INF 0
-#define ZILOG_CLOSING_WAIT_NONE 65535
-
-/*
- * Definitions for ZILOG_struct (and serial_struct) flags field
- */
-#define ZILOG_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes
- * on the callout port */
-#define ZILOG_FOURPORT 0x0002 /* Set OU1, OUT2 per AST Fourport settings */
-#define ZILOG_SAK 0x0004 /* Secure Attention Key (Orange book) */
-#define ZILOG_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */
-
-#define ZILOG_SPD_MASK 0x0030
-#define ZILOG_SPD_HI 0x0010 /* Use 56000 instead of 38400 bps */
-
-#define ZILOG_SPD_VHI 0x0020 /* Use 115200 instead of 38400 bps */
-#define ZILOG_SPD_CUST 0x0030 /* Use user-specified divisor */
-
-#define ZILOG_SKIP_TEST 0x0040 /* Skip UART test during autoconfiguration */
-#define ZILOG_AUTO_IRQ 0x0080 /* Do automatic IRQ during autoconfiguration */
-#define ZILOG_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
-#define ZILOG_PGRP_LOCKOUT 0x0200 /* Lock out cua opens based on pgrp */
-#define ZILOG_CALLOUT_NOHUP 0x0400 /* Don't do hangups for cua device */
-
-#define ZILOG_FLAGS 0x0FFF /* Possible legal ZILOG flags */
-#define ZILOG_USR_MASK 0x0430 /* Legal flags that non-privileged
- * users can set or reset */
-
-/* Internal flags used only by kernel/chr_drv/serial.c */
-#define ZILOG_INITIALIZED 0x80000000 /* Serial port was initialized */
-#define ZILOG_CALLOUT_ACTIVE 0x40000000 /* Call out device is active */
-#define ZILOG_NORMAL_ACTIVE 0x20000000 /* Normal device is active */
-#define ZILOG_BOOT_AUTOCONF 0x10000000 /* Autoconfigure port on bootup */
-#define ZILOG_CLOSING 0x08000000 /* Serial port is closing */
-#define ZILOG_CTS_FLOW 0x04000000 /* Do CTS flow control */
-#define ZILOG_CHECK_CD 0x02000000 /* i.e., CLOCAL */
-#define ZILOG_SLEEPING 0x01000000 /* have shut it down for sleep */
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-struct mac_serial;
-
-struct mac_zschannel {
- volatile unsigned char* control;
- volatile unsigned char* data;
- spinlock_t lock;
- /* Used for debugging */
- struct mac_serial* parent;
-};
-
-struct mac_dma {
- volatile struct dbdma_regs dma;
- volatile unsigned short res_count;
- volatile unsigned short command;
- volatile unsigned int buf_addr;
-};
-
-struct mac_serial {
- struct mac_serial *zs_next; /* For IRQ servicing chain */
- struct mac_zschannel *zs_channel; /* Channel registers */
- struct mac_zschannel *zs_chan_a; /* A side registers */
- unsigned char read_reg_zero;
- struct device_node* dev_node;
- spinlock_t lock;
-
- char soft_carrier; /* Use soft carrier on this channel */
- char break_abort; /* Is serial console in, so process brk/abrt */
- char kgdb_channel; /* Kgdb is running on this channel */
- char is_cons; /* Is this our console. */
- char is_internal_modem; /* is connected to an internal modem */
- char is_irda; /* is connected to an IrDA codec */
- int port_type; /* Port type for pmac_feature */
- unsigned char tx_active; /* character is being xmitted */
- unsigned char tx_stopped; /* output is suspended */
- unsigned char power_wait; /* waiting for power-up delay to expire */
-
- /* We need to know the current clock divisor
- * to read the bps rate the chip has currently
- * loaded.
- */
- unsigned char clk_divisor; /* May be 1, 16, 32, or 64 */
- int zs_baud;
-
- /* Current write register values */
- unsigned char curregs[NUM_ZSREGS];
-
- /* Values we need to set next opportunity */
- unsigned char pendregs[NUM_ZSREGS];
-
- char change_needed;
-
- int magic;
- int baud_base;
- int port;
- int irq;
- int flags; /* defined in tty.h */
- int type; /* UART type */
- struct tty_struct *tty;
- int read_status_mask;
- int ignore_status_mask;
- int timeout;
- int xmit_fifo_size;
- int custom_divisor;
- int x_char; /* xon/xoff character */
- int close_delay;
- unsigned short closing_wait;
- unsigned short closing_wait2;
- unsigned long event;
- unsigned long last_active;
- int line;
- int count; /* # of fd on device */
- int blocked_open; /* # of blocked opens */
- unsigned char *xmit_buf;
- int xmit_head;
- int xmit_tail;
- int xmit_cnt;
- struct work_struct tqueue;
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
-
- volatile struct dbdma_regs *tx_dma;
- int tx_dma_irq;
- volatile struct dbdma_cmd *tx_cmds;
- volatile struct mac_dma *rx;
- int rx_dma_irq;
- volatile struct dbdma_cmd **rx_cmds;
- unsigned char **rx_char_buf;
- unsigned char **rx_flag_buf;
-#define RX_BUF_SIZE 256
- int rx_nbuf;
- int rx_done_bytes;
- int rx_ubuf;
- int rx_fbuf;
-#define RX_NO_FBUF (-1)
- int rx_cbuf;
- spinlock_t rx_dma_lock;
- int has_dma;
- int dma_initted;
- void *dma_priv;
- struct timer_list poll_dma_timer;
-#define RX_DMA_TIMER (jiffies + 10*HZ/1000)
-
- struct timer_list powerup_timer;
-};
-
-
-#define SERIAL_MAGIC 0x5301
-
-/*
- * The size of the serial xmit buffer is 1 page, or 4096 bytes
- */
-#define SERIAL_XMIT_SIZE 4096
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP 0
-
-#endif /* __KERNEL__ */
-
-/* Conversion routines to/from brg time constants from/to bits
- * per second.
- */
-#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
-#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
-
-/* The Zilog register set */
-
-#define FLAG 0x7e
-
-/* Write Register 0 */
-#define R0 0 /* Register selects */
-#define R1 1
-#define R2 2
-#define R3 3
-#define R4 4
-#define R5 5
-#define R6 6
-#define R7 7
-#define R8 8
-#define R9 9
-#define R10 10
-#define R11 11
-#define R12 12
-#define R13 13
-#define R14 14
-#define R15 15
-
-#define NULLCODE 0 /* Null Code */
-#define POINT_HIGH 0x8 /* Select upper half of registers */
-#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
-#define SEND_ABORT 0x18 /* HDLC Abort */
-#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
-#define RES_Tx_P 0x28 /* Reset TxINT Pending */
-#define ERR_RES 0x30 /* Error Reset */
-#define RES_H_IUS 0x38 /* Reset highest IUS */
-
-#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
-#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
-#define RES_EOM_L 0xC0 /* Reset EOM latch */
-
-/* Write Register 1 */
-
-#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
-#define TxINT_ENAB 0x2 /* Tx Int Enable */
-#define PAR_SPEC 0x4 /* Parity is special condition */
-
-#define RxINT_DISAB 0 /* Rx Int Disable */
-#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
-#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
-#define INT_ERR_Rx 0x18 /* Int on error only */
-
-#define WT_RDY_RT 0x20 /* W/Req reflects recv if 1, xmit if 0 */
-#define WT_FN_RDYFN 0x40 /* W/Req pin is DMA request if 1, wait if 0 */
-#define WT_RDY_ENAB 0x80 /* Enable W/Req pin */
-
-/* Write Register #2 (Interrupt Vector) */
-
-/* Write Register 3 */
-
-#define RxENABLE 0x1 /* Rx Enable */
-#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
-#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
-#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
-#define ENT_HM 0x10 /* Enter Hunt Mode */
-#define AUTO_ENAB 0x20 /* Auto Enables */
-#define Rx5 0x0 /* Rx 5 Bits/Character */
-#define Rx7 0x40 /* Rx 7 Bits/Character */
-#define Rx6 0x80 /* Rx 6 Bits/Character */
-#define Rx8 0xc0 /* Rx 8 Bits/Character */
-#define RxNBITS_MASK 0xc0
-
-/* Write Register 4 */
-
-#define PAR_ENA 0x1 /* Parity Enable */
-#define PAR_EVEN 0x2 /* Parity Even/Odd* */
-
-#define SYNC_ENAB 0 /* Sync Modes Enable */
-#define SB1 0x4 /* 1 stop bit/char */
-#define SB15 0x8 /* 1.5 stop bits/char */
-#define SB2 0xc /* 2 stop bits/char */
-#define SB_MASK 0xc
-
-#define MONSYNC 0 /* 8 Bit Sync character */
-#define BISYNC 0x10 /* 16 bit sync character */
-#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
-#define EXTSYNC 0x30 /* External Sync Mode */
-
-#define X1CLK 0x0 /* x1 clock mode */
-#define X16CLK 0x40 /* x16 clock mode */
-#define X32CLK 0x80 /* x32 clock mode */
-#define X64CLK 0xC0 /* x64 clock mode */
-#define XCLK_MASK 0xC0
-
-/* Write Register 5 */
-
-#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
-#define RTS 0x2 /* RTS */
-#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
-#define TxENAB 0x8 /* Tx Enable */
-#define SND_BRK 0x10 /* Send Break */
-#define Tx5 0x0 /* Tx 5 bits (or less)/character */
-#define Tx7 0x20 /* Tx 7 bits/character */
-#define Tx6 0x40 /* Tx 6 bits/character */
-#define Tx8 0x60 /* Tx 8 bits/character */
-#define TxNBITS_MASK 0x60
-#define DTR 0x80 /* DTR */
-
-/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
-
-/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
-
-/* Write Register 7' (Some enhanced feature control) */
-#define ENEXREAD 0x40 /* Enable read of some write registers */
-
-/* Write Register 8 (transmit buffer) */
-
-/* Write Register 9 (Master interrupt control) */
-#define VIS 1 /* Vector Includes Status */
-#define NV 2 /* No Vector */
-#define DLC 4 /* Disable Lower Chain */
-#define MIE 8 /* Master Interrupt Enable */
-#define STATHI 0x10 /* Status high */
-#define NORESET 0 /* No reset on write to R9 */
-#define CHRB 0x40 /* Reset channel B */
-#define CHRA 0x80 /* Reset channel A */
-#define FHWRES 0xc0 /* Force hardware reset */
-
-/* Write Register 10 (misc control bits) */
-#define BIT6 1 /* 6 bit/8bit sync */
-#define LOOPMODE 2 /* SDLC Loop mode */
-#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
-#define MARKIDLE 8 /* Mark/flag on idle */
-#define GAOP 0x10 /* Go active on poll */
-#define NRZ 0 /* NRZ mode */
-#define NRZI 0x20 /* NRZI mode */
-#define FM1 0x40 /* FM1 (transition = 1) */
-#define FM0 0x60 /* FM0 (transition = 0) */
-#define CRCPS 0x80 /* CRC Preset I/O */
-
-/* Write Register 11 (Clock Mode control) */
-#define TRxCXT 0 /* TRxC = Xtal output */
-#define TRxCTC 1 /* TRxC = Transmit clock */
-#define TRxCBR 2 /* TRxC = BR Generator Output */
-#define TRxCDP 3 /* TRxC = DPLL output */
-#define TRxCOI 4 /* TRxC O/I */
-#define TCRTxCP 0 /* Transmit clock = RTxC pin */
-#define TCTRxCP 8 /* Transmit clock = TRxC pin */
-#define TCBR 0x10 /* Transmit clock = BR Generator output */
-#define TCDPLL 0x18 /* Transmit clock = DPLL output */
-#define RCRTxCP 0 /* Receive clock = RTxC pin */
-#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
-#define RCBR 0x40 /* Receive clock = BR Generator output */
-#define RCDPLL 0x60 /* Receive clock = DPLL output */
-#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
-
-/* Write Register 12 (lower byte of baud rate generator time constant) */
-
-/* Write Register 13 (upper byte of baud rate generator time constant) */
-
-/* Write Register 14 (Misc control bits) */
-#define BRENABL 1 /* Baud rate generator enable */
-#define BRSRC 2 /* Baud rate generator source */
-#define DTRREQ 4 /* DTR/Request function */
-#define AUTOECHO 8 /* Auto Echo */
-#define LOOPBAK 0x10 /* Local loopback */
-#define SEARCH 0x20 /* Enter search mode */
-#define RMC 0x40 /* Reset missing clock */
-#define DISDPLL 0x60 /* Disable DPLL */
-#define SSBR 0x80 /* Set DPLL source = BR generator */
-#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
-#define SFMM 0xc0 /* Set FM mode */
-#define SNRZI 0xe0 /* Set NRZI mode */
-
-/* Write Register 15 (external/status interrupt control) */
-#define EN85C30 1 /* Enable some 85c30-enhanced registers */
-#define ZCIE 2 /* Zero count IE */
-#define ENSTFIFO 4 /* Enable status FIFO (SDLC) */
-#define DCDIE 8 /* DCD IE */
-#define SYNCIE 0x10 /* Sync/hunt IE */
-#define CTSIE 0x20 /* CTS IE */
-#define TxUIE 0x40 /* Tx Underrun/EOM IE */
-#define BRKIE 0x80 /* Break/Abort IE */
-
-
-/* Read Register 0 */
-#define Rx_CH_AV 0x1 /* Rx Character Available */
-#define ZCOUNT 0x2 /* Zero count */
-#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
-#define DCD 0x8 /* DCD */
-#define SYNC_HUNT 0x10 /* Sync/hunt */
-#define CTS 0x20 /* CTS */
-#define TxEOM 0x40 /* Tx underrun */
-#define BRK_ABRT 0x80 /* Break/Abort */
-
-/* Read Register 1 */
-#define ALL_SNT 0x1 /* All sent */
-/* Residue Data for 8 Rx bits/char programmed */
-#define RES3 0x8 /* 0/3 */
-#define RES4 0x4 /* 0/4 */
-#define RES5 0xc /* 0/5 */
-#define RES6 0x2 /* 0/6 */
-#define RES7 0xa /* 0/7 */
-#define RES8 0x6 /* 0/8 */
-#define RES18 0xe /* 1/8 */
-#define RES28 0x0 /* 2/8 */
-/* Special Rx Condition Interrupts */
-#define PAR_ERR 0x10 /* Parity error */
-#define Rx_OVR 0x20 /* Rx Overrun Error */
-#define FRM_ERR 0x40 /* CRC/Framing Error */
-#define END_FR 0x80 /* End of Frame (SDLC) */
-
-/* Read Register 2 (channel b only) - Interrupt vector */
-#define CHB_Tx_EMPTY 0x00
-#define CHB_EXT_STAT 0x02
-#define CHB_Rx_AVAIL 0x04
-#define CHB_SPECIAL 0x06
-#define CHA_Tx_EMPTY 0x08
-#define CHA_EXT_STAT 0x0a
-#define CHA_Rx_AVAIL 0x0c
-#define CHA_SPECIAL 0x0e
-#define STATUS_MASK 0x06
-
-/* Read Register 3 (interrupt pending register) ch a only */
-#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
-#define CHBTxIP 0x2 /* Channel B Tx IP */
-#define CHBRxIP 0x4 /* Channel B Rx IP */
-#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
-#define CHATxIP 0x10 /* Channel A Tx IP */
-#define CHARxIP 0x20 /* Channel A Rx IP */
-
-/* Read Register 8 (receive data register) */
-
-/* Read Register 10 (misc status bits) */
-#define ONLOOP 2 /* On loop */
-#define LOOPSEND 0x10 /* Loop sending */
-#define CLK2MIS 0x40 /* Two clocks missing */
-#define CLK1MIS 0x80 /* One clock missing */
-
-/* Read Register 12 (lower byte of baud rate generator constant) */
-
-/* Read Register 13 (upper byte of baud rate generator constant) */
-
-/* Read Register 15 (value of WR 15) */
-
-/* Misc macros */
-#define ZS_CLEARERR(channel) (write_zsreg(channel, 0, ERR_RES))
-#define ZS_CLEARFIFO(channel) do { volatile unsigned char garbage; \
- garbage = read_zsdata(channel); \
- garbage = read_zsdata(channel); \
- garbage = read_zsdata(channel); \
- } while(0)
-
-#endif /* !(_MACSERIAL_H) */