diff options
Diffstat (limited to 'drivers/media/dvb')
| -rw-r--r-- | drivers/media/dvb/frontends/tda1004x.c | 30 |
1 files changed, 24 insertions, 6 deletions
diff --git a/drivers/media/dvb/frontends/tda1004x.c b/drivers/media/dvb/frontends/tda1004x.c index 1465ff77b0c..4981cef8b44 100644 --- a/drivers/media/dvb/frontends/tda1004x.c +++ b/drivers/media/dvb/frontends/tda1004x.c @@ -162,7 +162,7 @@ static int tda1004x_read_byte(struct tda1004x_state *state, int reg) if (ret != 2) { dprintk("%s: error reg=0x%x, ret=%i\n", __func__, reg, ret); - return -1; + return -EINVAL; } dprintk("%s: success reg=0x%x, data=0x%x, ret=%i\n", __func__, @@ -481,16 +481,18 @@ static void tda10046_init_plls(struct dvb_frontend* fe) static int tda10046_fwupload(struct dvb_frontend* fe) { struct tda1004x_state* state = fe->demodulator_priv; - int ret; + int ret, confc4; const struct firmware *fw; /* reset + wake up chip */ if (state->config->xtal_freq == TDA10046_XTAL_4M) { - tda1004x_write_byteI(state, TDA1004X_CONFC4, 0); + confc4 = 0; } else { dprintk("%s: 16MHz Xtal, reducing I2C speed\n", __func__); - tda1004x_write_byteI(state, TDA1004X_CONFC4, 0x80); + confc4 = 0x80; } + tda1004x_write_byteI(state, TDA1004X_CONFC4, confc4); + tda1004x_write_mask(state, TDA10046H_CONF_TRISTATE1, 1, 0); /* set GPIO 1 and 3 */ if (state->config->gpio_config != TDA10046_GPTRI) { @@ -508,13 +510,29 @@ static int tda10046_fwupload(struct dvb_frontend* fe) if (tda1004x_check_upload_ok(state) == 0) return 0; + /* + For i2c normal work, we need to slow down the bus speed. + However, the slow down breaks the eeprom firmware load. + So, use normal speed for eeprom booting and then restore the + i2c speed after that. Tested with MSI TV @nyware A/D board, + that comes with firmware version 29 inside their eeprom. + + It should also be noticed that no other I2C transfer should + be in course while booting from eeprom, otherwise, tda10046 + goes into an instable state. So, proper locking are needed + at the i2c bus master. + */ printk(KERN_INFO "tda1004x: trying to boot from eeprom\n"); - tda1004x_write_mask(state, TDA1004X_CONFC4, 4, 4); + tda1004x_write_byteI(state, TDA1004X_CONFC4, 4); msleep(300); - /* don't re-upload unless necessary */ + tda1004x_write_byteI(state, TDA1004X_CONFC4, confc4); + + /* Checks if eeprom firmware went without troubles */ if (tda1004x_check_upload_ok(state) == 0) return 0; + /* eeprom firmware didn't work. Load one manually. */ + if (state->config->request_firmware != NULL) { /* request the firmware, this will block until someone uploads it */ printk(KERN_INFO "tda1004x: waiting for firmware upload...\n"); |